Samsung SmartCam SNH-1010N User manual

1. Requirements for mobile devices
Hardware / Operating System
SmartCam
iOS
English
3. Tap <Start>.
Requirements
OS
- iOS 5.0/6.0/6.1/7.0/7.1
CPU
- 1GHz or higher
RAM
- 128MB or more (recommended),
RAM : 50MB (Minimum)
Network
Video Codec
Create new account
Back
Welcome to
- Must support Wi-Fi or 3G/LTE mobile
communication
Setup using 3 simple steps below.
Step 1. Sign up for an account
Step 2. Register your camera
- H.264
Step 3. Configure your camera
Recommended mobile devices - iPhone 4/5
Recommended Tablet PC
J

Start
- iPad 3/4
If you use 3G or 4G(LTE) data communication, excessive amount of
fees can be billed and may cause data delays or loss. Wi-Fi is
recommended.
4. Enter requested information.
M

Create new account
Back
ID
Email address is used to search for
account ID or password.
Create user ID between 8-14 characters using
letters and/or with numbers
User ID
Password
5. Read the terms and conditions,
and tap <Register>.
Now you can monitor critical events with your mobile
devices through the SmartCam application.
Download the application from App Store and install on
your mobile devices.
Create password between 10-14 characters using
both letters and numbers. Example: samsung135
Password
Confirm Password
2. Subscription
Name
Enter your name.
e-Mail
1. Run the downloaded application.
Example: xxxx@samsung.com
™ Search keywords for the application: “Samsung SmartCam”,
“Smartcam”, “Samsung techwin”, “Techwin”.
I agree to the Samsung Techwin's terms
and conditions.
Terms of Services
Register
2. Tap <Create new account>.
6. Tap <Next> when the menu on
the completion of a new member
registration pops up.
Login
ID
Enter User ID.
Password
Enter Password.
Remember me
Auto Login
M

●●●●●●
Name
e-Mail
Tap <Add Camera> after logging
in if you are already a member.
Account created. Tap <Next> to
setup the camera.
test
Logout
Cancel
Camera List
Login
Add Camera
Forgot your ID?
Forgot your password?
Create new account
Next
Refresh
M


You can only use it in a camera that has a Wi-Fi Direct sticker
attached to it.
M
Press the button, "Tap here to add registered camera" when you
register a camera being used in another account, in order to register
it immediately without setting it.
7. Tap <Wireless Setup>.


Select a camera that has the last
four digits of the serial number on
the back of the product.
.
10. After selecting a camera to
connect, tap <Next>.
Wi-Fi Direct connection
Settings
DIRECT-037N

Apple Network 8dfdc7
Enter 'smartcam' if a password is
required.
design
Cisco_WPS_57090
Is there a WiFi DIRECT
cker on the camera le
sticker
lens?
KT12580
Registration
00 : 02
Camera's LED will blink in blue
while searching for a WiFi router.
If a connection is made to the WiFi
router, the LED will be blue
consistently. After a short while,
while the camera is connecting to
the server, the LED will turn green.
Please wait until the status
LED on the camera changed
from blue to green.
It takes about 3 minutes.
Other...
Fi DIRE
CT
Wi
M
CHOOSE A NETWORK...
Registration
Back
12. The LED of the camera will
turn into green if a camera is
connected to Wi-Fi.
Wi-Fi
Wi-Fi
Ask to Join Networks
yes select Wireless Setup.
Se
If yes,
If not, select Optional Setup.
11. Select a WiFi router connected to
your camera.
Optional
Setup
•
Tap here to add registered camera
8. Tap <Next> after connecting
a camera according to the
instructions displayed on the
screen.
Back
Registration
Next
1
Plug in the power adapter
and connect it to the
camera. Camera can take
up to 2 minutes to boot
up.
When the camera LED
flashes in red, press the
WiFi button on the back
of the camera for 5
seconds.
3
The status LED on the
camera will change to light
green/yellow. Tap <Next>
9. On the next page, select WiFi
Setting on the mobile device.
Back
: Without the password, you
will not be connected to a WiFi
router.
• Other WiFi Networks : Enter the
SSID name, security type and
password.
If selected, it shows guide
on SSID and networking
procedures.
2
Registration
Go to Settings on your iPhone and select WiFi.
Select a camera that has the last four digits
of the serial number displayed on the back of
the camera.
Apple Network 8dfdc7
M
design
Click <Show Password> to check
your password.
Next
Create camera name and camera
password.
Camera Name
Example: Living Room
• Network password :
If you select a WiFi router with
the password, then the pop up
window will prompt you to enter
the password.
Camera password
KT12580
Use 1 - 8 numbers and/or letters
NETGEAR27
Confirm password
Show Password
If you don't want to save camera
password, please go to settings to disable
"Save camera password".
Other WiFi Networks
Cancel
Registration
Connect
Enter WiFi network password
Network password
Enter password
14. The camera registration is
completed.
Select <Yes> for a camera
setting.
Select <No> to view a live
screen.
M
Q W E R T Y U
I
O P
(If password is requested, enter 'smartcam'.)
A S D F G H J K L
Z X C V B N M
123
When you return to smartcam app, it will list the
available WiFi networks for the camera to connect to.

Registration
Cancel
Cisco_WPS_57090
•
DCIN 5V
: After entering the
password, connect to a WiFi
router.
13. Enter <Camera Name> and
<Camera password> and then
click <Next>.
Registration
Back
Select the WiFi network you
want the camera to connect to.
.
Wireless
Setup
space
Next


If you failed to register wirelessly,
please try again over a wireline.
Cameras may not be registered
depending on the settings of the
mobile device.
In this case, contact the service
center.
Registration
Camera registered successfully.
The camera settings can be set to
your preference. Continue with the
camera setup?
No
Yes
3. Camera List
10. If the camera is not detected,
please enter the camera serial
number manually.
Cable connection
7. Tap <Optional Setup>.
Registration
Back
M
Is there a WiFi DIRECT
sticker on the camera lens?

Next
Camera Move
No camera(s) found.
1. Move to the <Camera> item.
From the listed active cameras,
] on
tap the desired camera’s [
the right.
Check the serial number on the back of the
camera and enter it below.
For camera’s serial number
location, refer to [ ].
Fi DIRE
M
Serial number
CT
Wi
Registration
Cancel
Enter the 15-digit serial number.
Q W E R T Y U
I


O P
A S D F G H J K L
If yes, select Wireless Setup.
If not, select Optional Setup.
Wireless
Setup
Z X C V B N M
Optional
Setup
Tap here to add registered camera
8. Tap <Next> after connecting
a camera according to the
instructions displayed on the
screen.
Registration
Back
Next
11. Enter <Camera Name> and
<Camera password> and then
click <Next>.
M
1

Plug in the power adapter
and connect it to the
camera. Camera can take
up to 2 minutes to boot
up.
DCIN 5V
Click <Show Password> to check
your password.
Registration
Cancel
Refresh
Add Camera
test
test2
You cannot monitor an inactive
camera.
For a Wi-Fi Direct camera, you can
set the wireless network by
selecting an inactive camera.
Camera
Setup
List
test
About
return
space
123
Camera List
Logout
Next
2. Live, Event, Playback and Setup
icons will be displayed.
J
Create camera name and camera
password.

The supported functions may be
different depending on the model.
Camera Name
Example: Living Room
Camera password
Use 1 - 8 numbers and/or letters
Confirm password
test
2
Connect the camera to
the WiFi router using
network cable.
Show Password
Live
3
Tap <Next> when the
camera LED changes to
green.
(For *SNH-1010N, the
power LED turns to white)
9. Select the camera found and tap
<Next>.
M


Once the mobile device is
connected with the Wi-Fi network
like camera, it searches the camera
automatically.
Cameras already registered are not
searched.
Registration
Cancel
Found camera(s).
Select the camera listed below and tap <Next>. If
the cameras are not listed, enter the camera serial
number manually.
C8BG6V2C801011T
Next
12. The camera registration is
completed.
Select <Yes> for a camera
setting.
Select <No> to view a live
screen.
C8AT6V2C400079A
KHNL6V2D70002KN
KHNL6V2D70002KN
SMART6411ADT003
Playback
Setup
Delete Camera
Registration
1. If you want to delete a registered
camera, slide it from right to left in
the camera list.
M

Cameras may not be registered
depending on the settings of the
mobile device.
In this case, contact the service
center.
Camera List
Logout
Refresh
Add Camera
test
Delete
2. Tap <Delete>.
C8BG6V2C801011T
C8AT6V2C400079A
Event
If you don't want to save camera
password, please go to settings to disable
"Save camera password".
Camera registered successfully.
The camera settings can be set to
your preference. Continue with the
camera setup?
No
3. Tap <OK>.
Are you sure you want to remove this
camera?
Cancel
OK
Yes
Serial number
Enter the 15-digit serial number.
Camera
Setup
About
4. Live Video
1. Tap the desired camera’s [
tap the <Live> icon.
M

] or
Camera List
Logout
If there is the latest version of
firmware, when you make a live
video connection, a pop up will
appear so that you can update your
camera’s firmware.
test
Back
Back
test
test
Event
Playback
Camera List
Logout
Description
A user can record audio and play the recorded audio
Audio playing through the camera speaker.
 You can record a max of 10 audio files.
Information
Current audio/video information is displayed.
IR Lighting
If you select <Night Vision> in general settings, IR lighting
will operate for two minutes.
Setup
J
Refresh
Add Camera
Camera password
b
c

The supported functions may be different depending on the model.
Two-way Audio
test
|Enter the camera password.
No.
test2
Cancel
OK
I
Z X C V B N M
123
Camera
space
Setup
Description
Manual
Recording
A user can manually save the video in the SD card.
 If there is storage space of 10% while the SD card
overwrite function is not activated, you cannot perform
manual recording.
b
Capture
You can capture and save a still image from the video.
c
Two-way
Audio
The microphone for two-way audio between cameras
and mobile devices is activated.
 Refer to the bidirectional audio function.
Back
test
O P
A S D F G H J K L

No.
c
test2
Q W E R T Y U
M
Live Video
test
Live
2. Enter the <Camera password>
for the camera selected. This is
the same camera password you
created at the time you registered
the camera.
Within 20 seconds, it will start
streaming.
Refresh
Add Camera
return
About
According to the network service provider’s policy, or the network
connection status, it may take a while to load.
In general network environments, high quality video is
provided.
HQ

Depending on the network status or service provider's
policy, HQ video may not be provided. In this case,
video is displayed for seven minutes.

In relay mode, no HQ video is provided. For more
details, refer to "Relay Mode".
1. Tap on the Two-way Audio icon.
2. The Mic icon will appear.
3. Talk while pressing down the mic icon. The voice can be
heard from the speaker on the camera. After finishing
talking, press down the icon for two seconds so that the
audio information will be transmitted through the network.
4. Even if you did not activate the two-way audio function,
you can receive the audio sound of the video. In addition,
the microphone setting should be at least 1 or higher if you
want to use the two-way audio function.
Melody
The selected melody will be heard through the camera
speaker.
Brightness
control
Adjusts the screen brightness.

Flip control
Flips the video image.

Motion zone
It detects motion within the area set by the user.

Refer to the motion zone functions.
J

When there are multiple users logged on to the camera, first person
who tap the Talk icon will have the control.
While the bidirectional audio is on, you need to tap the bidirectional
audio icon again to cancel the function.
In relay mode, there is no audio. For more details, refer to "Relay
Mode".
Cancel
Clear
OK
1. Tap the motion zone icon.
2. Connect to the motion zone mode.
3. After touching the video, drag it to set the area.

You can set a max of three motion zones.
4. If you want to run the motion zone in the area set, tap
<OK>.

Relay mode
General setting
If the network condition is not good and a connection is
unstable, then you can use the relay mode to view video for
seven minutes.
] mark is
When the relay mode connection is made, the [
displayed on the video, and to maintain stable connections,
there will be no audio or HQ video.
1. Tap <General>.



If the router UPnP setting is not set, then a relay mode connection
can be made. Depending on the model of router used, a different
setting method is used. Refer to the user manual.
If a camera is connected to the multiple router, or the wired/wireless
network environments for camera and mobile device are unstable, a
relay mode connection can be made.
If you have trouble connection to the camera, visit "http://www.
samsungsmartcam.com", go to support page, and refer to
"Troubleshooting" on it.
Motion is detected only in the set area.

test
Speaker
• Camera Name : Camera name is
used to easily identify the camera
when you have more than one.
• Speaker/Mic : Adjust the
volume for the camera’s built-in
mic or speaker.
M

Mic
Audio REC
Night Vision
WDR
Display date
If you set the mic to zero, there will be no
live sound and no audio event and also
there is no recording in the SD card.
• Audio REC : The voice can be
recorded or deleted by users.
• Night Vision : Set the IR lighting.
Check <Night Vision> to set
the camera to switch to the
night vision mode automatically.
Motion zone function only operates if motion detection is activated. In
<Setup> - <Event>, set motion detection.
Camera Name
Apply
.
J
2. Configure the basic camera
settings.
General
Back
Save camera password
.
Motion zone
Change camera password
Audio List
Back
01. Add personalized audio clip
02. Add personalized audio clip
03. Add personalized audio clip
04. Add personalized audio clip
5. To delete the set area, press <Clear> and <OK>.
If you want to exit the motion zone setting mode, tap
<Cancel>.
5. Camera Setup
To control digital zooming
Tap the <Setup> icon to configure a camera to be monitored.
M
test
List
Back

Setup
In the case of SNH-1010N, you can
check <Night Vision> for a
camera to automatically operate the
IR lighting for two minutes
depending on the brightness of the
neighboring areas.
• WDR : You can compensate for
the backlight by making a dark
area brighter, and a bright area
darker.
You can also zoom in by pinch open using two
fingers on the screen. To zoom out, pinch close
on the screen.
Touch and hold to drag the screen in any
direction to reveal the hidden part of the image
if enlarged bigger than the screen.
test

05. Add personalized audio clip
06. Add personalized audio clip
07. Add personalized audio clip
08. Add personalized audio clip
09. Add personalized audio clip
10. Add personalized audio clip
Password
Back
Apply
Current Password
SNH-P6410BN supported
New Password
General
Network
test
• Display date : Displays the date/
time on the live video.
Use 1 - 8 numbers and/or letters
Confirm password
Show Password
M

Time
Current digital zooming level is noted next to the digital zoom box,
and digital zooming supports zooming up to x4.
Event
Live
Event
Playback
Setup
SD Card
• Save camera password : You
will be connected to your
camera without having to enter
the password.
• Change camera password :
Change the current camera
password.
If you don't want to save camera password,
please go to settings to disable "Save
camera password".
• Firmware Version : You can check the current version and
the latest distributed version and even make updates.
If there is the latest version of firmware, when you make a live
video connection, a pop up will appear so that you can update
your camera’s firmware.
3. Tap <Apply>.
J

The supported functions may be different depending on the model.
2. Configure the wireless network.
• WiFi : Display the list of WiFi
router that you can use.
M

Back
Network
WiFi
From the list below. Please select the
WiFi network you wish to use.
2. Set your event items.
• Event alert : Detection of
motion/audio or saving of video
in the Picasa or Google drive is
notified to the user.
• Google account setup : You
can upload pictures on Picasa
through the Google account.
Apple Network 8dfdc7
design
If the Wi-Fi receiving sensitivity is
poor, receiving a video may not
work properly. Move the location of
the camera to adjust receiving
sensitivity.
1. Tap the <Event>.
• Motion/Audio Detection :
Specify whether to trigger the
alarm or not, and specify the
sensitivity.
The higher the sensitivity is, the
subtler motion/audio events will
be detected.
Network setting
1. Tap the <Network>.
Event setting
Cisco_WPS_57090
M
KT12580

NETGEAR27
If you wish to send an event alarm
to the Picasa/Google drive, you
must register the Google account
first.
Setting Google Drive
Event
Back
Apply
You can set the Google Drive through request for authentication.
1. Log onto the Google account.
Event alert
2. Tap <Accept>.
An authentication code is
created.
Motion Detection
Sensitivity
Audio Detection
Sensitivity
.
• status LED : You can turn on or off the LED on your camera.
Google account setup
3. Tap <Send authentication
code>.
Google Drive setting is
completed.
Back
Google Drive
Login to your Google account to receive the
authentication code.
This app would like to:
View and manage Google Drive files
that you have opened or created with
this app
View metadata for files and documents
in your Google Drive
Google Drive for Samsung SmartCam and Google will use
this information in accordance with their respective terms of
service and privacy policies.
Cancel
Picasa
Accept
Authentication code
You can use your Google account to store
tore
ore
event detected images to Google+
Send authentication code
Google
Cancel
OK
When an event is detected, camera will
automatically upload images to your
Google+ account as a private photo.
Back
Google Drive
Login to your Google account to receive the
authentication code.
Google e-Mail
xxxxxxx
Google password
Please copy this code, switch to your application
and paste it there:
.
4/RF6he608emlcKYoh************************
Other WiFi Networks
• Google Drive : A 30-second
video clip is uploaded
automatically to the user's
Google Drive account.
Time setting
1. Tap <Time>.
2. Set the camera’s clock.
• Time zone : Select your region.
Back
Time
Time
Show Password
Need to create a Google
account.
Move
If you cannot access a Google account,
then log into the following Google page
to permit access and try again.
Permit Google access
Move
Apply
2014-04-20 09:20:05
J

Time zone
(GMT) Greenwich Mean Time
• Daylight Saving Time : Check
this option if you live in a country
or region where DST(Daylight
Saving Time) is applied.
• Picasa : Sends event images to
the user’s Picasa account.
4/RF6he608emlcKYoh************************
If your model supports an SD card
slot, then video is saved in the SD card, not Google Drive.
3. Tap <Apply>.
Daylight Saving Time
J

Authentication code
The supported functions may be different depending on the model.
Send authentication code
6. Event List
1. Tap the <Event> icon, and the
Google Drive and the Picasa
event link are displayed.
SD card setting
J




Only applicable to those models that provide SD card slots.
You need to purchase an SD card if you want to use it.
M
Note that inserting an SD card which has been used for other
purposes into the camera may delete the data.

2. Detected events will be saved in the server and displayed in
the event list.
test
List
Google Drive icon: Tap
the Google Drive icon to
play video.
Events are listed only when you
have registered the Google account
and set the Google Drive/Picasa.
Audio
Detection icon
test
1. Tap <SD Card>.
Event
Back
Before removing the SD card, deactivate the Use SD card setting.
If not, the SD card can get damaged.
Apr-20-2014
14:26:23
Apr-20-2014
14:25:30
Apr-20-2014
Setup
Back
Edit
Picasa icon:
Tap on the Picasa icon
to see picture.
14:24:20
Live
Event
Playback
Setup
Motion Detection
Icon
Apr-20-2014
14:22:18
Apr-20-2014
14:21:18
Apr-20-2014
14:19:24
M
test

General

Network
Time
Event

SD Card
2. Set the SD card item.
• Use SD card : When you set
motion/audio, the video will be
automatically saved in the SD
card.
• Continuous Recording : Video
is saved regardless of the event
that occurs.
• SD card Overwrite : If the SD
card capacity is insufficient,
then it will automatically start
overwriting the oldest data.
SD Card
Back
Apr-20-2014
14:17:35
Apr-20-2014
14:16:16
Apr-20-2014
While uploading files in Google
Drive or Picasa, no event is
detected.
14:15:56
Motion Detection
- test Apr-20-2014 09:21:18
test
When an event is detected, an
alarm is received and when image
or video uploading is finished, then
one more alarm is received.
Live
General
Network
Time
Event
Continuous Recording
SD Card
If continuous recording is not selected,
ed,
d, only
o
Motion and Audio detected video clips
ips will
be saved.
SD card Overwrite
Status
Format
Size (Free/Total) : 3.18 / 3.66 GB
• Format : Delete all the data in the SD card.
14:18:17
Setup
Back
Use SD card
• Status : Check the remaining
capacity of the SD card.
3. Tap <Apply>.
Apply
Apr-20-2014
You will get a notification prompt
when event is detected by the
camera.
Event
Cancel
M




If your model supports an SD card slot, then video is saved in the SD
card, not Google Drive and you can view video in SD player.
If you select the Google Drive icon/Picasa icon, the linked web page
is displayed.
You can watch the video only when the Google Drive account is the
same with the one used in the camera.
If you download a file, you can play the video on a video player. But, if
the video player has no codec installed to support the video, the
video won't be played smoothly so please install the codec that
supports H.264 and G.711 first.
7. Playback
Deleting All Events
SD Save
1. After tapping <Edit>, tap
<Delete>.
Event
Delete
Finish
J

Apr-20-2014

14:26:23
2. Tap on the <Delete All> to clear
the event list.
Apr-20-2014
14:25:30
Apr-20-2014
14:24:20
Apr-20-2014

14:22:18
Apr-20-2014
14:21:18
Apr-20-2014
14:19:24

Apr-20-2014
14:18:17
Apr-20-2014
14:17:35
Delete All
Apr-20-2014
Continuous recording automatically saves video to SD memory every
five minutes.
Manual recording runs if you press the manual recording button in
live screen. If you switch to another screen without turning it off,
video will be saved for additional 30 seconds before stopping.
Event recording saves motion or audio for thirty seconds and if
motion or audio is detected again in the meantime, the amount of
saving time is extended.
In case of manual/event recording during continuous recording, the
manual/event recording video playing time can be separated by five
minutes.
5. On the screen, a circular shaped
timeline (24 hours) will be
displayed. The time zone with
the search data is classified by
colors.
Back
►
Playback
09:04:57
2014.04.01
6. Check the timeline and drag it to
the desired playing time [
] to
set the video playing start time or
enter the time on your own.
• Previous/Next video : Move to
the previous/next video to the
selected video.
Previous video
Next video
14:16:16
Cancel
Apr-20-2014
14:15:56
1. Tap the <Playback> icon.
J
Deleting Each Event
1. After tapping <Edit> tap [
].
Event
Delete

7. Tap the < ► > button.
Play the video data.
test
List
Only applicable to those models
that provide SD card slots.
•
Finish
•
Apr-20-2014
14:26:23
14:25:30
Apr-20-2014
14:24:20
Apr-20-2014
test
14:22:18
Apr-20-2014
14:21:18
Apr-20-2014
14:19:24
Live
Event
Playback
Setup
Apr-20-2014
14:18:17
Apr-20-2014
14:17:35
Apr-20-2014
14:16:16
Apr-20-2014
14:15:56
Event
Delete
Apr-20-2014
14:26:23
Apr-20-2014
14:25:30
Finish
Delete
2. Searchable dates are displayed
on the calendar.
Tap the left/right < ,
>
button to select between year/
month in the top of the calendar
to move to the previous or next
month.
Playback
Back
◄
Sun
Apr 2014
Mon
►
Tue
Wed
Thu
Fri
Sat
30 31
1
2
3
4
5
6
8
9
10 11 12
7
13 14 15 16 17 18 19
20 21 22 23 24 25 26
Apr-20-2014
27 28 29 30
14:24:20
Apr-20-2014
14:22:18
Apr-20-2014
14:21:18
Apr-20-2014
14:19:24
Apr-20-2014
14:18:17
Apr-20-2014
14:17:35
Apr-20-2014
14:16:16
Apr-20-2014
14:15:56
3. Select the desired date of search.
4. Select an event type that you
want to search.

You can select a saved video type in
the playing list.
Type
Motion Detection
1
2
3
00:39:58
test
00:44:57
: Drag the time bar and play the video at the desired
time.
Apr-20-2014
2. Tap on <Delete> to delete the
event.
/
: You can play or pause
the video.
Back
8. Auto Login Setup
2. If you activate <Auto Login>,
then when the app is terminated,
you can set the app to
automatically log in.
Logout
10. Info.
1. Move to the <Setup> item.
Setup
Auto Login
Logout
Checking the S/W info
Setup
Auto Login
1. Move to the <About> item.
Setting Alert
ON
Logout
About
ON
Setting Alert
You can change Push Alert settings in iPhone
Settings>Notifications.
2. You can check the information of
the currently installed software.
You can change Push Alert settings in iPhone
Settings>Notifications.
Version
v2.36
Created Date
2014. 06. 25
Copyright
Samsung Techwin
This software uses FFmpeg under LGPL v2.1
Help Guide
Camera
Setup
About
Camera
About
Camera
.
2. From pop-up and push notice,
you can select the SmartCam
notice on the Setting menu of the
mobile device.
Setup
Back
Setup
About
SmartCam
ALERT STYLE
Help guides
None
Banners
1. Move to the <About> item.
Alerts
Alerts require an action before proceeding.
Banners appear at the top of the screen and
go away automatically.
2. Tap the <Help Guide> menu to see help.
Badge App Icon
M
Sounds
ALERTS
Show in Notification Center
Include
5 Recent Items
ms
.
1. Move to the <Setup> item.
9. Alarm setting

The language set in the mobile device is automatically recognized,
and the app is provided in that language. Help is available in seven
different languages.