Craftsman 113.177778 Owner`s manual

r
Save This Manual
For Future Reference
SF=ARS
owner's
manual
MODEL NO.
113.177778
CRRFTSMRN®
Serial
Number
Model and serial
numbers may be found
on the handle. You
should record both
model and serial
numbers in a safe place
for future use.
FOR YOUR
SAFETY
16 GALLON
FULL BLOWING
WET/DRY VAC
• assembly
• operating
• repair parts
READ ALL
INSTRUCTIONS
CAREFULLY
J
Sears, Roebuck and Co., Hoffman
Part' No. SP6465
Estates, IL. 60179 U.S.A.
Printed in U.S.A.
•
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
WET/DRY
_I
VACS
f within one year from the date of purchase, this Craftsman Wet/Dry Vac fails
due to a defect in material or workmanship, Sears will repair it, free of charge.
If this Craftsman Wet/Dry Vac is used for commercial or rental purposes,
this warranty coverage applies for only 90 days from date of purchase.
Warranty Service Is Available By Simply Contacting The Nearest Sears Service Center/department
Throughout The United States.
This warranty applies only while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
b,_
Sears, Roebuck and Co., D817 WA, Hoffman
Estates, IL. 60179
.,
IMPORTANT SAFETY INSTRUCTIONS
Safety is a combination of common
sense, staying alert and knowing how
your vac works. Read this manual to
understand the vac.
Safety Signal Words
DANGER: means if the safety information
is not followed someone will be seriously
injured or killed.
WARNING: means if the safety information is not followed someone could be
seriously
injured or killed.
CAUTION: means if the safety information is not followed someone may be
injured.
When using your WeVDry Vac, follow basic
safety precautions including the following.
WARNING-Toreduce
the risk of fire, electric shock, or
injury:
Read and understand this owner's manual
and all labels on the Wet/Dry Vac before
operating. Use only as described in this
manual. To reduce the risk of personal
injury or damage to Wet/Dry Vac, use only
Sears Craftsman recommended accessories.
Sparks inside the motor can ignite flammable vapors or dust. To reduce the risk
of fire or explosion:
• Do not vacuum, or use this Wet/Dry
Vac, near flammable or combustible
liquids, gases, or explosive dusts, such
as gasoline or other fuels, lighter fluid,
cleaners, oil- based paints, natural
gas, hydrogen, coal dust, magnesium
dust, grain dust, or gun powder.
• Do not use Wet/Dry Vac as a sprayer.
Do not vacuum anything that is burning or
smoking, such as cigarettes, matches, or
hot ashes.
Do not vacuum fireplace soot or ash. This
is a very fine dust which will not be captured by the filter and may cause damage.
To reduce the risk of health hazards from
vapors or dusts, do not vacuum toxic
materials.
Do not use or store near hazardous materials.
To reduce the risk of electric shock, do
not expose to rain. Store indoors.
Do not allow Wet/Dry Vac to be used as a
toy. Close attention is necessary when
used by or near children.
Do not use this Wet/Dry Vac with a tom filter or without the filter installed except
when vacuuming liquids as described in
the operation section of this manual.
Do not leave Wet/Dry Vac when plugged
in. Unplug from outlet when not in use and
before servicing. Turn off WeVDry Vac
before unplugging.
WARNING:
To reduce the risk of fire
or electric shock, do not run vac
unattended.
To reduce the risk of falls, use extra care
when cleaning on stairs.
To reduce the risk of injury from accidental starting, unplug power cord before
changing or cleaning filter.
This Wet/Dry Vac is double-insulated,
eliminating the need for a separate
grounding system. Use only identical
replacement parts. Read the instructions
for Servicing Double-Insulated Wet/Dry
Vacs before servicing.
Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
Do not use with damaged cord, plug or
other parts. If your Wet/Dry Vac is not
working as it should, has missing parts,
has been dropped, damaged, left outdoors, or dropped into water, return it to a
Sears Service Center.
Observe the following warnings that
appear on the motor housing of your Wet/
Dry Vac.
Do not pull or carry by cord, use cord as
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not
run Wet/Dry Vac over cord. Keep cord
away from heated surfaces.
_-_
DOUBLE INSULATED
GROUNDING NOT REQUIRED
WHEN SERVICING USEONLY
IDENTICAL REPLACEMENT PARTS
WARNING: To reduce the risk of
Do not handle plug or the Wet/Dry Vac
with wet hands.
electric shock - do not expose to
rain - store indoors.
Do not put any object into ventilation
openings. Do not vacuum with any ventilation openings blocked; keep free of dust,
lint, hair or anything that may reduce air
flow.
WARNING: For your own safety, read
and understand owner's manual. Do
not pick up hot ashes, coals, toxic,
flammable or other hazardous materials. Do not use around explosive
liquids or vapors.
Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
SAVE THESE INSTRUCTIONS
The operation of any utility vac or blower
can result in foreign objects being blown
into the eyes, which can result in severe
eye damage. Always wear safety goggles
complying with ANSI Z87.1 (shown on
package) before commencing operation.
Safety Goggles are available at Sears
retail stores.
Use only extension cords that are rated
for outdoor use. Extension cords in poor
condition or that are too small in wire size
can pose fire and shock hazards. When
using an extension cord, be sure it is in
good condition. Using any extension cord
will cause some loss of power. To keep
the loss to a minimum, use the following
table to choose the minimum wire size
extension cord.
To reduce the risk of hearing damage,
wear ear protectors when using the vac
for extended hours or when using it in a
noisy area.
For dusty operations, wear dust mask.
Extension
Cord Length
0-50 Ft.
50-100 Ft.
3
Gauge
A.W.G.
14
12
Introduction
This Wet/Dry Vac is intended
hold use only.
Owner's
for house-
Item
Page
Warranty Information ............................. 2
Safety Instructions .................................
2
introduction ............................................
4
Unpacking and Checking
Carton Contents ............................. 4
Assembly ...............................................
5
Operation ...............................................
8
Maintenance ........................................
10
Repair Parts ........................................
12
IMPORTANT NOTE
Please Read Carefully
Static Shocks Are Common - In dry
areas or when the relative humidity of the
air is low. To reduce the frequency of
static shocks in your home the best remedy is to add moisture to the air with a
console humidifier.
Unpacking
and Checking Carton Contents
Remove entire contents of carton. Check,
A
G_
each item against the Carton Contents
List. Notify your Sears Store immediately
if any parts are damaged or missing.
Carton Contents
. Key
A
B
C
D
E
F
G*
H*
j*
K*
L*
M
N
P
Q
R
Manual Contents
List
Description ...........................
Qty.
Vac Assembly .............................
1
Pos-I-Lock Hose Assembly ......... 1
Utility Nozzle ...............................
1
Wet Nozzle ..................................
1
Car Nozzle ..................................
1
Hose Lock ...................................
1
Filter Nut .....................................
1
Filter Plate ...................................
1
Filter (Red Stripe) ........................ 1
Filter Cage ..................................
1
Float ............................................
1
Extension Wands ........................ 2
Male/Male Connector .................. 1
Caster Foot For Storage ............. 4
Caster .........................................
4
Owners Manual ........................... 1
B
*These items may come preassembled.
If they are not present in the carton
check the vac power head to see if they
are preassembled.
4
Float/Cage
WARNING:
For your own safety,
never connect
outlet
Assembly
plug to power
until all assembly
complete
instructions.
the safety
source
steps
and you have
understood
NOTE:
because
are
read and
with any parts damaged
filter cage and the center
vac
in the wrong
ring of the lid. Pry
the tab out of the slot. Tilt the cage and lift
away from the lid. To replace, follow float/
or missing.
cage assembly instructions.
1. Place the power assembly of vac
upside down into the drum.
Filter
Cage "-I"
2. Locate the float. Place the float over the
opening in the center of the lid with the
words "This Side Towards Lid" laying
face down over the hole.
WARNING:
the float is placed
way, use a flat blade screwdriver
and insert
the blade near one of the tabs between the
and operation
Do not operate
If filter cage needs to be removed,
Float_
Power
Assembly
/
To reduce the risk of
personal injury or damage to vac be
sure to keep hands, fingers, or any
other foreign objects out of the center opening when assembling the
float.
3. Line up filter cage tabs with the slots in
the center ring of the lid.
4. Push on the filter cage until the tabs
snap into the slots for a secure fit.
Slots (3)
Filter Assembly
1. Carefully slide the filter over the filter
cage, sliding it over the center ring covering the 3 slots until the filter stops
against the lid.
I_;;;_'_----Filter
_"*---Filter
Nut
Plate
2. Place the hole in the filter plate over
threaded screw of the filter cage.
3. Gently push on the filter plate to seat
the rubber ring of the filter inside the circular channel of the filter plate.
4. Place filter nut onto threaded screw and
ge
tighten it down. Finger tighten only.
NOTE: Lever of filter nut should be away
from plate as shown.
IMPORTANT: Do not overtighten as this
may deform or crack the filter plate or filter
cage.
NOTE: Your filter has a red stripe that
matches an in-store displayer. When you
visit your local Sears store, just remember the
color of your stripe for the correct size filter.
5
Caster/Caster
Foot Assembly
1. Remove the power assembly
dust drum and set aside,
from the
7. Turn the drum upright.
2. Tum the dust drum upside down on the
floor.
3. Insert the caster feet into the bottom of
Caster_
drum, as shown (4 places).
4. Push on the caster foot until the foot is
flush with bottom of the dust drum.
Caster-,.Foot
5. Insert the caster stem into the socket of
Pin
the caster foot, as shown (4 places).
6. Push on the caster until the ball on the
caster stem is inserted all the way into
the socket. You will hear the ball snap
into the socket and the caster will swivel
Hole
Dust Drum
easily when positioning is correct.
Vac Assembly
1. Line up vacuum port in power assembly
with drain cap located on the front of
the drum.
onto the drum lip of the channel.
5. Make sure that the locking tabs are
snapped in place to prevent the power
assembly from coming off. (See inset
below.)
2. Place power assembly on top of drum
with the handles snug against the drum
channel.
Cord Storage
3. Be sure power assembly completely
covers the top of the drum so leakage
does not occur.
Simply wrap the power cord around the lid
assembly and snap the connector on the
plug to a wrap of the cord.
4. Push down on top of the handles to
cause the flexible locking tabs to hook
Power Assembly
Push
Down
4
Pull
Out
Flexible
Locking
Tab
Drum
Channel
Lid
Handle
\
• Drain
Do Not Force Flexible
Tab Beyond Stop Tab
Drum
Tab
Locking Tabs
6
6. Insert the push button end of the "Pos-ILock" hose into the inlet of the vac. The
into the swivel
forcing
hose should snap into place. To remove
the hose from the vac, press the release
button in the hose assembly and pull the
hose out of the vac inlet, as shown.
end of the original
the sections
tightly.
Purchase
together
a 9-16917
- OR hose-hose
tor. Install the hose-hose
7. Place the utility nozzle securely on the
opposite end of the hose and the vac is
ready for use.
NOTE" The opposite end of the hose is
removable if more hoses need to be
the other
connec-
connector
end of the hose connected
connect
hose by
until they fit
on the
to the vac and
hose to the hose con-
nector.
Release
Button
\
Press and
Pull
c:3>
attached for more length from the vac. To
remove the swivel portion of the hose,
grasp the hose swivel and firmly pull it out
of the flexible hose. Connect the soft end
of a second hose (accessory
Cord Wrap
#9-17820)
, On-Off
Switch
Blowing
Port _
Lid !
Handle
Vacuum
Port
Release
Button
Swivel
End
Drum
Utility
Larger
Opening
Power
Assembly
Hose
Drain
Of Hose
Hose
Lock
To Store Your Accessories
1. Slide extension handles and accessories into the slotted areas of the
caster feet for storage.
2. To remove the accessories, rotate and
pull upward.
7
Operation
WARNING
To reduce the risk of fire or explosion, do not operate this vac In areas with
flammable gases, vapors or explosive dust In the air. Flammable gases or
vapors Include but are not limited to; lighter fluid, solvent type cleaners, oilbase paints, gasoline, alcohol or aerosol sprays. Explosive dusts Include but
are not limited to; coal, magnesium, grain or gun powder. Do not vacuum
explosive dust, flammable or combustible liquids or hot ashes. Do not use
this vac as a sprayer. To reduce the risk of health hazards from vapors or
dusts, do not vacuum toxic materials.
CAUTION: To reduce risk of hearing
damage wear ear protectors when
using the vac for extended hours or
when using It In e noisy area. The
operation of any utility vac can
result in foreign objects being
blown into the eyes, which can
result In severe eye damage. Always
wear safety goggles complying with
ANSI Z87.1 (shown on Package)
before commencing operation.
Safety Goggles are available at
Sears retail stores.
To reduce the risk of electric shock, this
appliance has a polarized plug (one blade
is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way.
After you plug the power cord into the outlet, turn the unit on by pushing the switch
from position "O" to position "1".The symbols used on the motor cover are international "On & Off" symbols. "O" is the
symbol for "OFF" and "1" is the symbol for
"ON",
0 =OFF I:ON
Vacuuming
Dry Materials
1. The filter must always be in correct
position to reduce the risk of leaks and
possible damage to vac.
2. When using your vac to pick up very
fine dust, it will be necessary for you to
empty the drum and clean the filter at
more frequent intervals to maintain
peak vac performance.
NOTE: A dry filter is necessary to pick up
dry material. If you use your vac to pick up
dust when the filter is wet, the filter will
clog quickly and be very difficult to clean.
3. If your filter is wet but you need to use
the vac to pick up dry material, you can
quickly dry the filter by running the vac
without hose attached for about 10 minutes. The clean air rushing through the
vac will help dry the filter.
The optional Craftsman High Efficiency
Filter, stock number 9-17918 will do a better job stopping the very fine particles
than the 9-17816 filter.
Vacuuming Liquids
1. When picking up small amounts of liquid the filter may be left in place.
2. When picking up large amounts of liquid we recommend that the filter be
removed. If the filter is not removed, it
will become saturated and misting may
appear in the exhaust.
3. After using the vac to pick up liquids,
the filter must be dried to reduce the
risk of possible mildew and damage to
the filter.
4. When the liquid in the drum reaches a
predetermined level, the float mechanism will rise automatically to cut off airflow. When this happens, turn off the
vac, unplug the power cord, and empty
the drum. You will know that the float
has risen because vac airflow ceases
and the motor noise will become higher
in pitch, due to increased motor speed.
IMPORTANT: To reduce the risk of damage to the vac do not run motor with float
in raised positign_
Emptying
the Drum
Moving the Vac
1. Should it become necessary to pick the
vac up to move it, DO NOT pick the vac
up by the lid handles unless dust drum
WARNING: To reduce the risk of
Injury from accidental starting,
unplug power cord before emptying
the drum.
1. The vac
for easy
unscrew
site side
is empty. To reduce the risk of dropping
the vac due to latches releasing or possible part breakage, pick the vac up by
the lip of the dust drum.
comes equipped with a drain
emptying of liquids. Simply
the drain cap and lift the opposlightly to empty the drum.
Blowing Feature
Your vac features "Full Blowing". It can
blow sawdust and other debris. Follow the
2. Another option is to remove the power
assembly. Pull the flexible latches outward on each side of the lid to release
from the drum.
steps below to use your vac as a blower.
3. While holding the latches out, lift the
power assembly up and away from the
drum.
4. Lay power assembly upside down on a
clean area while emptying drum.
5. Dump the drum contents into the proper
waste disposal container.
WARNING:
I
WARNING: To reduce the risk of
Injury to bystanders, keep them
clear of blowing debris.
J
1
1. Locate blowing port of your vac.
2. Insert the male/male adapter into the
locking tab adapter end of the hose.
Insert the opposite end of the male/
male adapter into the blowing port of
the vac.
To reduce the risk of
back Injury or falls, do not lift a vac
heavy with liquid or debris. Scoop
or drain enough contents out to
make the vac light enough to lift
comfortably.
Cord Wrap/Carry
WARNING: Always wear safety goggles complying with ANSI Z87.1
before using as a blower.
3. (Optional) Attach extension wand to
opposite end of hose, then place a
blower nozzle on the wand.
Handle
4. Turn vac on and you are ready to use
your vac as a blower.
The wet/dry vac has a convenient cord
wrap area/carry handle designed on the
rear of the vac. Simply, wrap the power
cord around the handle and snap the connector on the plug to a wrap of the cord
and the cord is wrapped for storage.
Sears recommended accessories are
available at Sears retail stores. The Sears
Blower Nozzle Stock No. 9-16933 and
extension handles Stock No. 9-16964 are
recommended for blowing debris.
Male/Male
Locking Hose End
Swivel End
Extension
Wand
(Optional)
(Optional)
9
I
Maintenance
IMPORTANT:
Filter
WARNING:
To reduce the risk of
injury from accidental starting,
unplug power cord before changing
or cleaning filter.
NOTE: This filter is made of high quality
paper designed to stop very small particles of dust. The filter can be used for wet
or dry pick up.
when removing
Creases in the
installation but
performance
Handle the filter carefully
to clean or installing it.
filter pleats may occur from
creases will not affect the
of the filter.
Cleaning
Your filter should be cleaned often to
maintain
peak vac performance.
Be sure to dry the filter before storing or
picking up dry debris.
IMPORTANT: After cleaning, check
filter for tears or small holes. Do not
filter with holes or tears in it. Even a
hole can cause a lot of dust to come
the
use a
small
out of
your vac. Replace it immediately.
Removal
To remove the filter for cleaning or
replacement, unscrew the filter nut from
the filter cage, remove filter plate and lift
)ff filter.
WARNING:
Do not remove the filter
cage. It Is there to help prevent your
fingers from getting into the blower
wheel.
To reduce the risk of dam-
age to the blower wheel and motor,
always reinstall the filter before using the
vac for dry material pickup.
Dry Filter
1. Some removal of dry debris can be
accomplished without removing the filter from the vac. Slap your hand on top
of the power assembly while the vac is
turned off.
2. For best cleaning results due to accumulated dust, clean the filter in an open
area. Cleaning SHOULD be done outdoors and not in the living quarters.
3. After filter removal from vac, remove the
dry debris by gently tapping the filter
against the inside wall of your dust
drum. The debris will loosen and fall.
4. For thorough cleaning of dry filter with
fine dust (no debris), run water through
it as described under "Wet Filter".
Wet Filter
After filter is removed, run water through
the filter from a hose or spigot. Take care
that water pressure from the hose is not
strong enough to damage filter. Remember: To dry a filter quickly, reinstall the filter on the vac and allow the unit to run for
approximately 10 minutes. The clean air
rushing through the filter will dry it.
Installation
Refer to page 5, "Filter Assembly".
Allow the filter to dry before storing the
vac.
Wet/Dry
Vac
To keep your Wet/Dry Vac looking its best,
clean the outside with a cloth dampened
with warm water and mild soap.
To clean the drum:
WARNING: To assure product
SAFETY and RELIABILITY, repairs
and adjustment should be performed by Sears Service Centers,
always using Sears replacement
parts.
1. Dump debris out.
2. Wash drum thoroughly with warm water
and mild soap.
3. Wipe out with dry cloth.
NOTE: If your casters are noisy, you may
put a drop of oil on the roller shaft to make
them quieter.
10
Wet Nozzle
2. Using both hands, lower the nozzle
body onto the insert and squeegee with
the round opening of the nozzle closest
to you. With fingers on the far side and
thumbs holding the latches of the
removable insert, flip the nozzle over so
the latches are on the top and the round
inlet opening is facing away from you.
Make sure the squeegee stays on the
insert pins.
To pick up liquids off a smooth surface,
use the 2-1/2" wet nozzle accessory supplied with your wet/dry vac. To use this
nozzle, simply attach the nozzle to the
end of an extension wand.
Connect a second extension wand to the
first, and connect the 2-1/2" x 7' hose to
the extension wand.
Liquids may be picked up by dragging the
nozzle across the surface. The squeegee
will dry the surface as you vacuum.
Replacement rubber for the squeegee
nozzle may be obtained through Sears
Parts. If the rubber becomes worn, it may
be flipped over for use on the opposite
side or replaced. (Replacement service
part #822256). To reverse or replace the
squeegee:
3. Press down with each thumb below the
latching tabs until you see and hear the
removable insert snap into the nozzle
body. Snap the latches over the locking
tabs into their original position.
1. Lay the wet nozzle on a flat surface with
the round inlet opening facing up and
the two latches close to you as shown.
Latches
Nozzle
Body
4. Inspect the pins of the insert to make
sure they fit through the holes of the
squeegee and fit into the matching slots
in the nozzle body.
Insert
2. Using both hands, position each thumb
on the removable insert, (below the
latches) and two fingers of each hand
on each latch, lift and disengage the
two latches from the tabs on the nozzle
NOTE: If the pins are out of position,
hold the nozzle assembly with both
hands and gently twist in opposite
directions. The insert pins should snap
into proper position.
Twist
Twist
Backward
Forward
body.
3. Gently pull the latches toward yourself
to remove the insert.
To reinstall the removable insert correctly,
follow these steps:
1. Place the removable insert on a flat surface with the pins positioned upward
and the latches close to you as shown.
Place the rubber squeegee on the
insert, with the pins fitting through the
matching holes in the squeegee. (Make
sure the new working edge is located
farthest from you.)
[,,:
_-
_-
-:
_-
_,
•
_
_"
-
-_
._
The wet nozzle assembly is ready for wet
pickup use.
_-
I
11
Repair Parts
16 Gallon Wet/Dry Vac
Model Number 113.177778
Always order by Part Number - Not by Key Number
WARNING
SERVICING
OF DOUBLE-INSULATED
WET/DRY
VAC
In a double-insulated
Wet/Dry Vac, two systems of insulation are provided
instead of grounding. No grounding means is provided on a double-insulated
appliance, nor should a means for grounding be added. Servicing a doubleinsulated Wet/Dry Vac requires extreme care and knowledge of the system, and
should be done only by qualified service personnel. Replacement parts for a
double-insulated
Wet/Dry Vac must be identical to the parts they replace. Your
double-insulated
Wet/Dry Vac is marked with the words "DOUBLE INSULATED"
and the symbol
ance.
I-_-I(square
Key
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
within a square) may also be marked on the appli-
Part No.
73180
824941
822467-5
824967
STD611007
818793
818961
818413-2
15534-1
73352
823690-4
509238
9-17816
9-16937
9-16938
809544-3
73185
9-16990
73102
826356-1
827596
821421-10
815096
826355-1
826354
822256
SP6465
Description
Toggle Switch
Motor Cover
Cord w/plug
Motor (Includes Key No's 7,thru 10)
* Screw, Pan Hd. Ty "AB" 10x3/4
Lid Gasket
Spacer
Blower Wheel
Washer
Nut, Hex Flange 1/4-20
Lid
Float/Filter Cage
t Filter (Red Stripe)
t Filter Plate
1 Filter Nut
Dust Drum
Drain Cap
t Caster Foot w/Storage
Casters
t Hose 2-1/2" x 7'
1"Adapter Hoselock
Ring "O"
Adapter Hose
Spring Tab
End Hose Interlock
Squeegee (Not Illustrated)
Owners Manual (Not illustrated)
t Stock Item - May Be Secured Through The Hardware
Stores
* Standard Hardware
Item - May Be Purchased
12
Locally.
Department Of Most Sears Retail
Repair Parts
16 Gallon Wet/Dry Vac
Model Number 113.177778
J
2
J
13-_
10
22
21
19 -''"
_
24
2O
J
25
13
£RRFTSMRN®
Accessories
and Attachments
Get more versatility from your Craftsman wet/dry vacuum by adding these accessories.
Additional wet/dry vac accessories may be purchased
or Sears/Craftsman
Power and Hand Tool Catalog.
at your local Sears retail store
@
17820 2-1/2" x7' Hose
16922 Utility Nozzle
16978 Car Nozzle
16926 14" Floor
Brush
17822
Pos-I-Lock
Hose
17817 Wet Nozzle
16933 Blower Nozzle
16947, 16948
Inflator Nozzle
16964 Extension
Wands
16925 Dry Nozzle
16902 Crevice Tool
16901 Dusting
Brush
i
i
16931/16990
Caster
Feet for Storage
NOTE: Most Accessories
17816 Paper Pleated
Filter
Are Available
14
16939 & 16940
Drum Llners
In 2-1/2 Inch And 1o1/4 Inch Sizes
16934
Hose Grip
16917
Hose Joiner
16930
Hose
Lock
16935
Gutter
Sawdust Collection Series
Whole-shop
Sawdust
Manifold-Type
Collection
System
29964
Radial Arm Saw
Dust Collection Kit
29963
Table Saw Dust
Collection Kit
29962
15
Nozzle
For in-home
major brand repair service:
Call 24 hours a day, 7 days a week
1-800-4-MY-HOME
Para pedir servicio
(1-800-469-4663)
de reparaci6n
a domicilio
- 1-800-676-5811
For the repair or replacement parts you need:
Call 6 am - 11 pm CST, 7 days a week
PartsDirect
1-800-366-PART
Para ordenar
(1-800-366-7278)
piezas con entrega a domicilio
- 1-800-659-7084
For the location of a Sears Parts and Repair Center
in your area:
Call 24 hours a day, 7 days a week
1-800-488-1222
For information
on purchasing
a Sears Maintenance
Agreement
or to inquire about an existing Agreement:
Call 9 am - 5 pro, Monday - Saturday
1-800-827-6655
SEARS
HomeCentrai
TI_, r_)d_l
and serial numbers
When requesting
service
following information:
•
•
Product Type
Part Number
© 2002
will be found
or ordering
•
•
5M
on the handle.
parts,
always
provide
the
Model Number
Part Description
Emerson
Sears,
Part No. SP6465
Roebuck
and Co., Chicago,
Form No. SP6465
IL. 60179
U.S.A.
Printed in U.S.A.
3/02