Sharp XG-E3500U Instruction manual

Dear SHARP Customer
Welcome to the SHARP Family. We are pleased that you are now the owner of a SHARP Color
LCD Projector built for outstanding quality, reliability and performance.
Every SHARP Color LCD Projector is adjusted for a proper picture and has passed through the
most stringent quality control tests at the factory. We have prepared this OPERATION MANUAL
so that you have the ability to adjust the picture and color to your personal viewing preference.
We sincerely hope that you will be satisfied with the quality and performance of your Color LCD
Projector for many years to come.
Please read the instructions carefully, and keep them handy for future reference.
IMPORTANT
For your assistance in reporting the loss or
theft of your Color LCD Projector, please
record the Serial Number located on the rear
of the projector and retain this information.
Model No.: XG-E3500U
Serial No.:
Important Information
There are two important reasons for prompt warranty registration of your new SHARP LCD
Projector, using the REGISTRATION CARD packed with the projector.
1) WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2) CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act,
PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE. U.S.A. ONLY
WARNING: High brightness light source, do not stare into the beam of light, or view directly.
Be especially careful that children do not stare directly into the beam of light.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk or electric
shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
CAUTION
E-1
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the interference at his own expense.
U.S.A. ONLY
The enclosed RGB signal cable and Macintosh adaptor must be used with the device. The cable and adaptor are
provided to ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
Important Safeguards
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to ensure
your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to defeat the safeguards incorporated into this LCD Projector, observe the following basic rules for
its installation, use and servicing. For your own protection and reliable usage of your LCD Projector, please be sure
to read these “Important Safeguards” carefully before use.
1) Read Instructions – All the safety and operating instructions should be read before the product is operated.
2) Retain Instructions – The safety and operating instructions should be retained for future reference.
3) Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.
4) Follow Instructions – All operating and use instructions should be followed.
5) Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6) Attachments – Do not use attachments not recommended by the product manufacturer as they may cause
hazards.
7) Water and Moisture – Do not use this product near water – for example, near a bathtub, wash bowl, kitchen sink,
or laundry tub; in a wet basement; or near a swimming pool; and the like.
8) Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the
product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by
the manufacturer.
9) A product and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product and cart combination to overturn.
10) Ventilation – Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the
product and to protect it from overheating, and these openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11) Power Sources – This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your home, consult your product dealer or local power
company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12) Grounding or Polarization – This product is equipped with a three-wire grounding-type plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.
13) Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
E-2
14) Lightning – For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent
damage to the product due to lightning and power-line surges.
15) Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
16) Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any
kind on the product.
17) Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
18) Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the product to normal
operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service.
19) Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or with the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
20) Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine that the product is in proper operating condition.
21) Wall or Ceiling Mounting – The product should be mounted to a wall or ceiling only as recommended by the
manufacturer.
22) Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Cautions Concerning the Laser Pointer
CAUTION
LASER RADIATIONDO NOT STARE INTO BEAM
WAVE LENGTH : 670nm
MAX. OUTPUT : 1mW
CLASS II LASER PRODUCT
"COMPLIES WITH 21 CFR SUBCHAPTER J"
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
U.S.A. ONLY
TEL : 1-800-BE-SHARP
REMOTE CONTROL
MODEL NO. : RRMCG1392CESA
DC6V (1.5VX4PCS.)
MADE IN JAPAN
FABRIQUÉ AU JAPON
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE.
The laser pointer on the remote control
emits a laser beam from the laser light
window shown in the figure to the left. The
laser emitted is a class II laser; therefore,
do not look into the laser window or shine
the laser beam on yourself or other people.
The three marks to the left are the caution
labels for the laser beam.
Always use the laser pointer at temperatures between 41°F and 104°F (+5°C and
+40°C).
Caution: Use of controls or adjustments or
performance of procedures other than
those specified herein may result in hazardous radiation exposure.
LASER LIGHT WINDOW
E-3
Notes on Operation
About the Temperature Monitor Function:
• If the projector starts to overheat due to set-up problems or a dirty air filter, “TEMP.” will flash in
the upper-left corner of the picture. If the temperature continues to rise, then the lamp will turn
off, the TEMPERATURE WARNING indicator will flash, and after a 90-second cooling-off
period the power will shut off. Refer to page 32, “Maintenance Indicators,” when the “TEMP.”
warning appears in the picture.
About the Lamp Monitor Function:
• When the projector is turned on after the lamp has been in use for more than 1,400 hours, the
yellow “LAMP” display will flash on the screen for 60 seconds, as shown on the right. This is to
alert you that it is time to replace the lamp. At this point, take your projector to the nearest
Authorized Sharp Industrial LCD Products Dealer or Service Center to have the lamp replaced.
• If the lamp is used for more than 1,500 hours, the projector power will automatically turn off,
and the projector will be in STANDBY mode.
• Refer to page 32, “Maintenance Indicators,” when the “LAMP” display warning appears.
TEMP.
LAMP
Caution: If “LAMP” begins to flash on the screen, be sure to take your projector to the nearest Authorized Sharp
Industrial LCD Products Dealer or Service Center to have the lamp replaced.
Outstanding Features
Allows easy projection of large screen, full-color computer
and video images.
• Can be projected directly onto a video screen or white
wall.
• Lightweight, convergence-free system for easy
installation.
DIRECT COMPUTER COMPATIBILITY
A multi-scan RGB Input accepts signals from SXGA
(1,280 dots × 1,024 lines compressed), XGA (1,024 dots
× 768 lines), SVGA (800 dots × 600 lines), VGA and Mac
(1,024 dots × 768 lines maximum) compatible computers
without the need for any additional hardware.
FLEXIBLE USE
In addition to the standard front projection mode, the
menu driven functions can be used to instantly reverse
the image for rear projection, and invert the image for
ceiling mounting.
POWER ZOOM AND FOCUS
• Provides simple screen-size adjustments from either the
projector or the remote control.
• Screen projection size adjusts from 40 to 500 inches.
LENS SHIFT
The lens can be easily raised and lowered to minimize or
eliminate “Keystone” type effects.
HIGH PICTURE QUALITY
The three LCD panels contain 786,432 × RGB pixels to
achieve exceptionally bright, high quality video images
with up to 520 scan doubled TV lines of resolution (700
lines for S-video).
VERSATILE REMOTE CONTROL
• Built-in wireless mouse allows simultaneous operation
of projector and computer.
• Built-in Laser Pointer for professional presentations.
BUILT-IN STEREO SPEAKERS
Built in 3 W + 3 W stereo amplifiers and speakers eliminate the need for external audio components.
USE WITH “PLUG AND PLAY”
“Plug and play” compatible with VESA DDC 1 and DDC
2B standards.
E-4
Location of Controls
FRONT VIEW
ON/OFF
Speakers
POWER ON/OFF button
Remote sensor
POWER indicator
POWER
LAMP REPLACEMENT
indicator
LAMP
Cooling fan
(Exhaust vent)
TEMPERATURE WARNING
indicator
TEMP.
Carrying handle
Cautions:
Lamp cage cover
• The exhaust vent, the lamp cage cover and adjacent areas may be extremely hot during
(Natural ventilation)
projector operation. To prevent injury, do not touch these areas until they have sufficiently
cooled.
• Allow at least 4⬙ (10 cm) of space between the cooling fan (exhaust vent) and the other
nearest wall or obstruction.
• If the cooling fan becomes obstructed, a protection device will automatically turn off the
projector lamp. This does not indicate a malfunction. Remove the projector plug from the
wall outlet and wait 10 minutes. Then turn on the power by plugging the cord back in. This
will return the projector to its normal mode.
Cooling fan
(Intake vent)
OPERATION PANEL ON SIDE OF PROJECTOR
MENU
ENTER
MN
EN
ADJ.
LENS
BLACK
SCREEN
LN
B
MUTE
VOLUME
INPUT
SELECT
IN
BLACK
MENU
ADJUSTMENT
VOLUME UPSCREEN
button
DOWN buttons
button
( / , / ) buttons
ENTER button
LENS button MUTE button
INPUT SELECT
button
SIDE AND REAR VIEW
Cooling fan (Intake vent)
COMPOSITE
VIDEO INPUT 1
Video: BNC
Audio: RCA
S-VIDEO INPUT
(4-pin mini DIN)
COMPOSITE
VIDEO INPUT 2
Video: BNC
Audio: RCA
MAIN POWER
switch
RS-232C (D-sub 9-pin)
Use when controlling the projector
from your personal computer.
MOUSE TERMINAL
Use when operating your personal computer with the
wireless mouse remote control.
Left Terminal: D-sub 9-pin (for IBM/Mac)
Right Terminal: 9-pin mini DIN (for NEC in JAPAN)
WIRED REMOTE
CONTROL INPUT
(3.5 mm Mono Minijack)
COMPUTER AUDIO INPUT
(3.5 mm Stereo Minijack)
AUDIO OUTPUT: RCA
DC 5 V 0.5 A OUTPUT
AC INLET
COMPUTER RGB Filter ON/OFF COMPUTER RGB INPUT 2: BNC
(R, G/G-SYNC, B, H/C-SYNC, V-SYNC)
INPUT 1 connector (HD-15) switch
COMPOSITE VIDEO OUTPUT: BNC
COMPUTER RGB OUTPUT connector (HD-15)
Notes:
• The DC 5 V OUTPUT jack cannot supply a current of more than 0.5 A.
• When connecting a Macintosh Series computer that outputs C-SYNC, connect the cable to the COMPUTER RGB 2 INPUT
H-SYNC input terminal.
E-5
Operating the Wireless Mouse Remote Control
The functions of your personal computer’s mouse have been built into the remote control
enabling you to operate your projector and personal computer with only the remote control.
1. Slide the MAIN POWER switch on the side of the unit on.
2. Press the POWER ON button on the front panel of the remote control to turn the projector power on.
3. When using the remote control as a wireless mouse, move the MOUSE/ADJUSTMENT sliding switch to the
MOUSE position. When using the remote control to operate the projector, move the MOUSE/ADJUSTMENT
sliding switch to the ADJ. position. To activate the remote control key back-light feature, press the LIGHT button
on the remote control. The colors of the buttons will change as shown in the table at the bottom of this page.
Wireless Mouse Remote Control
FRONT VIEW
SIDE VIEW
TRANSMIT indicator
MAIN POWER switch
of remote control
OFF
R/C
ON
MUTE button
Note:
When transporting the
remote control, turn off
the MAIN POWER
switch to avoid draining
the batteries.
VOL
ON
MUTE
POWER ON/OFF
buttons
VOLUME UP-DOWN
buttons
OFF
BLACK SCREEN/
LENS
BLACK SCREEN/
LENS button
LASER/
MENU
B
LN
MN
LASER POINTER/MENU
button
LEFT-CLICK button
MOUSE/ADJUSTMENT
( / ),( / ) buttons
RIGHT-CLICK/ENTER
button
R-CLICK/ENTER
Remote control handling precautions
INPUT SELECT
INPUT SELECT
buttons
INPUT CHECK button
MOUSE label
MOUSE/ADJUSTMENT
switch
DATA1
DATA2
VIDEO1
VIDEO2
CHECK
MOUSE
ADJ.
LIGHT
LIGHT button
Using the remote control
in a dark room
• The laser beam used in this product is harmless when
directed onto the skin, however please be careful not to
project the beam directly into the eyes. Do not stare into
the beam using an optical instrument.
• Do not expose the remote control to shocks, liquids or
high humidity.
The remote control may not operate normally if exposed
to direct sunlight or other intense light sources. Should
this happen, reposition the light source or the LCD
ADJ. label Projector.
LCD PROJECTOR
• Press the LIGHT button to turn
on the back-lights for the
operation buttons for about 5
seconds. The back-light colors
are explained in the table to the
right.
Note:
• If the MAIN POWER switch on the remote control is left on
for more than 10 minutes without operation, the power will
automatically turn off. To turn the power back on, press any
button on the remote control for at least one second.
When you change the setting of the MOUSE/ADJUSTMENT switch, the
functions of certain buttons on the remote control change. You can tell
which function the button currently possesses by the color of its backlight display.
Button name
LASER POINTER/MENU
RIGHT-CLICK/ENTER
MOUSE/ADJUSTMENT
LEFT-CLICK
BLACK SCREEN/LENS
POWER ON/OFF
VOLUME UP-DOWN
MUTE
VIDEO 1
VIDEO 2
DATA 1
DATA 2
INPUT CHECK
Position of MOUSE/ADJUSTMENT switch
MOUSE
ADJ.
LASER POINTER (GREEN)
MENU (RED)
RIGHT-CLICK (GREEN)
ENTER (RED)
MOUSE (NOT LIT)
ADJ. / , / (NOT LIT)
ON (NOT LIT)
–––
BLACK SCREEN (GREEN)
LENS (RED)
ON (RED)
E-6
TOP VIEW
Using the optional cable with the remote control
• When the remote control cannot be used due to the
range or positioning of the projector (rear projection,
etc.), connect the optional cable from the Wired
Remote Control Input jack on the remote control to
the Wired Remote Input on the side of the projector.
REMOTE CONTROL
SIGNAL TRANSMITTER
Note:
• The signal transmitter does not function when the optional
cable is connected to the remote control.
WIRED REMOTE CONTROL INPUT
(3.5 mm Mono Minijack)
LASER LIGHT WINDOW
Laser light shines out of
this window.
"COMPLIES WITH 21 CFR SUBCHAPTER J"
CAUTION
LASER RADIATIONDO NOT STARE INTO BEAM
WAVE LENGTH : 670nm
MAX. OUTPUT : 1mW
CLASS II LASER PRODUCT
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
U.S.A. ONLY
TEL : 1-800-BE-SHARP
REMOTE CONTROL
MODEL NO. : RRMCG1392CESA
DC6V (1.5VX4PCS.)
MADE IN JAPAN
FABRIQUÉ AU JAPON
The laser pointer on the remote control emits
a laser beam from the laser light window
shown in the figure to the left. The laser
emitted is a class II laser; therefore, do not
look into the laser window or shine the laser
beam on yourself or other people. The two
marks to the left are the caution labels for the
laser beam.
Always use the laser pointer at temperatures
between 41°F and 104°F (+5°C and +40°C).
Inserting the Batteries
REAR VIEW
Remove the battery cover as shown and insert four AA
size batteries making sure their polarities match the (+)
and (–) marks inside the battery compartment.
Press in and
downward on
the arrow
mark and
remove.
Insert the side
tabs into their
slots and press
in the cover
until properly
seated.
Notes:
Incorrect use of batteries may cause them to leak or burst.
• Insert the batteries with the (+) and (–) polarities as indicated.
• Remove the batteries if the remote control will not be operated
for an extended period of time.
• Maintain the batteries in a clean condition.
• Do not mix different brands of batteries. The life expectancy of
the new batteries will be shortened and the old batteries may
leak.
• When the batteries have been used up, remove them
immediately to prevent leakage and damage. Leaked battery
fluid may irritate the skin. Remove any battery fluid by wiping
with a cloth.
• Due to storage conditions and the shelf life of the supplied
batteries, they may run out after a short time. If so, replace
them with new batteries as soon as possible.
Remote control positioning
Reception range
Transmission range
30°
30°
Max. distance: 23⬘ (7 m)
30°
E-7
45°
Use the remote control as shown in the figures on the left.
Note:
• The signal from the remote control can be reflected off the
screen for easy operation. However, the effective distance of
the signal may differ due to the screen material.
Wireless Mouse Functions
m The wireless mouse functions and laser pointer on the remote control can help you create a more
professional presentation.
• By attaching the provided mouse cable to both the mouse terminal on your projector and the mouse
terminal on your personal computer, you can use the wireless mouse built into the remote control,
instead of the mouse equipped with your personal computer, to operate your personal computer. The
wireless mouse functions will work with personal computers compatible with IBM PS/2, serial (RS232C) or Apple ADB type mouse systems.
Projector
Connection Example
Personal computer
To mouse terminal
Supplied mouse cable (for IBM PS/2, serial and Apple ADB type mouse)
ON
Functions and Operations
R/C
VOL
ON
OFF
MUTE
POWER ON/OFF
buttons
OFF
BLACK SCREEN/
LENS
LASER/
MENU
B
LN
LASER POINTER button
LEFT-CLICK button
MN
R-CLICK/ENTER
MAIN POWER switch of
remote control
MOUSE buttons
RIGHT-CLICK button
INPUT SELECT
MOUSE/ADJUSTMENT
sliding switch
DATA1
DATA2
VIDEO1
VIDEO2
CHECK
MOUSE
ADJ.
LIGHT
LCD PROJECTOR
•
•
•
•
First, connect the units as shown above, and turn the projector power on.
Second, turn the computer power on.
Next, slide the MAIN POWER switch on the side of the remote control.
When using the remote control as a wireless mouse, move the MOUSE/ADJUSTMENT sliding switch to the MOUSE position.
Notes:
• In some situations the wireless mouse may be inoperable if your computer port is not correctly set-up. Please refer to your computer owners
manual for details on setting-up/installing the correct Mouse Driver.
• Do not connect or remove the mouse control cable to/from your computer while it is on. This may damage your computer.
• Do not connect the mouse input terminal for IBM/Mac and the mouse input terminal for PC98 simultaneously.
MOUSE buttons
By lightly pressing the up/down and right/left arrow buttons located on the front
of the remote control, you can move the mouse cursor on your monitor screen.
Note: The amount of pressure applied to the MOUSE button determines the speed the
mouse cursor travels. Pressing lightly on the periphery of the MOUSE button
makes the mouse cursor move slowly. Pressing hard makes it move quickly.
LEFT-CLICK button
Mouse cursor
The LEFT-CLICK button on the back of the remote control corresponds to the left button of
the mouse on two-button mouse systems.
The RIGHT-CLICK button on the front of the remote control corresponds to the right button
on two-button mouse systems.
RIGHT-CLICK button
Note: For one-button mouse systems use either the LEFT-CLICK or RIGHT-CLICK button.
LASER POINTER button
CAUTION
LASER RADIATIONDO NOT STARE INTO BEAM
WAVE LENGTH : 670nm
MAX. OUTPUT : 1mW
CLASS II LASER PRODUCT
Press the LASER POINTER button to activate the laser pointer.
When the button is pressed, the light stays on; when the button is released, the light goes off.
However, even when the button is pressed continuously, the light automatically goes off 1
minute after it goes on. To turn it on again press the laser pointer button one more time.
"COMPLIES WITH 21 CFR SUBCHAPTER J"
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
U.S.A. ONLY
TEL : 1-800-BE-SHARP
REMOTE CONTROL
MODEL NO. : RRMCG1392CESA
DC6V (1.5VX4PCS.)
MADE IN JAPAN
FABRIQUÉ AU JAPON
The laser pointer on the remote control emits
a laser beam from the laser light window. The
laser emitted is a class II laser; therefore, do
not look into the laser window or shine the
laser beam on yourself or other people. The
two marks to the left are the caution labels for
the laser beam.
Always use the laser pointer at temperatures
between 41°F and 104°F (+5°C and +40°C).
E-8
Setting Up the Projector
Using the Focus, Zoom and Lens Shift
• Lens Shift, Zoom, Focus and Reversed/Inverted Image mode functions broaden your options
for projector placement.
• See pages 10, 12 and 13 for details on projector setup.
Zoom
SIDE VIEW
Ceiling setting
Lens Shift
Invert Image
Table setting
Zoom
1. Turn on the MAIN POWER.
Turn on the MAIN POWER switch on the side of the
projector.
2
2. Turn on the POWER.
ON/OFF
POWER
LAMP
POWER
indicator
Press the POWER ON/OFF button on the projector or the
POWER ON button on the remote control to turn on the
power.
TEMP.
FOCUS
3
3. Press the LENS button.
• When using the remote control to adjust the picture,
FOCUS
↔
←
SHIFT
←
SHIFT
•
ZOOM
•
←
ZOOM
SHIFT
move the MOUSE/ADJUSTMENT sliding switch to the
ADJUSTMENT position. When the LENS button on the
remote control or on the projector is pressed, the LENS
adjustment mode is indicated for about 8 seconds.
If the LENS button is pressed while the mode is indicated on the screen, the picture adjustment mode
changes as shown on the left.
You can adjust the picture as shown on the left by
pressing the ADJUSTMENT ( ) or ( ) buttons for
FOCUS and ZOOM or the ADJUSTMENT ( ) or ( )
buttons for SHIFT while in ADJUST mode.
Note:
• Do not attempt to adjust the lens by hand as it may damage the lens
mechanism.
• Adjust the focus until the picture on the screen is sharp.
• The focus pattern appears on the screen.
• The picture can be adjusted to the desired size within
the zoom lens range.
• The picture can be adjusted within the shift range of the
lens.
E-9
Projector Distance and Picture Size Relationship
m The motorized zoom lens allows adjustment to the image size within the projector’s range.
m The picture can be focused from a minimum of approximately 4.5 ft (1.4 m) to a maximum of 96.3 ft (29.4 m)
from the screen. Please set up the projector within this range.
Projection distance (L)
Picture size
Maximum projection distance Minimum projection distance
(diag.)
96.3 ft (29.4 m)
60.5 ft (18.4 m)
500 in. (400⬙ W ⳯ 300⬙ H)
77.0 ft (23.5 m)
48.3 ft (14.7 m)
400 in. (320⬙ W ⳯ 240⬙ H)
300 in. (240⬙ W ⳯ 180⬙ H)
57.7 ft (17.6 m)
36.1 ft (11.0 m)
38.3 ft (11.7 m)
23.9 ft (7.3 m)
200 in. (160⬙ W ⳯ 120⬙ H)
150 in. (120⬙ W ⳯ 90⬙ H)
28.6 ft (8.7 m)
17.9 ft (5.5 m)
100 in. (80⬙ W ⳯ 60⬙ H)
19.0 ft (5.8 m)
11.8 ft (3.6 m)
80 in. (64⬙ W ⳯ 48⬙ H)
15.1 ft (4.6 m)
9.3 ft (2.9 m)
60 in. (48⬙ W ⳯ 36⬙ H)
11.2 ft (3.4 m)
6.9 ft (2.1 m)
40 in. (32⬙ W ⳯ 24⬙ H)
7.3 ft (2.2 m)
4.5 ft (1.4 m)
Distance from screen
Picture size: 100 inches (254 cm)
Zoom adjustment range: 19.0 ft–11.8 ft
90°
The formula for picture size and projection distance
y1 = (0.059x – 0.1175) ⳯ 3.28
y2 = (0.0371x – 0.1211) ⳯ 3.28
x : Picture size (diag.) (inches)
y1 : Maximum projection distance (ft)
y2 : Minimum projection distance (ft)
90°
Minimum L: 11.8 ft (3.6 m)
Note: There is an error of Ⳳ4 inches (Ⳳ10 cm) in the
formula above.
Maximum L: 19.0 ft (5.8 m)
Distance between lens and screen: L
Diagram shows the lens shift position set at the factory.
• Above is an illustration of maximum and minimum projection distances for the XG-E3500U with a picture size of 100 inches
(254 cm). Move the projector forward or back if the edges of the image are distorted.
Height of Projector
m This projector is equipped with a lens shift function that lets you adjust the projection height without moving the
projector.
Distance from lens center to lower edge of screen (H)
Picture size
m Adjust to match the setup configu(diag.)
Lower lens shift position
Upper lens shift position
ration.
500 in. (400⬙ W ⳯ 300⬙ H)
400 in. (320⬙ W ⳯ 240⬙ H)
300 in. (240⬙ W ⳯ 180⬙ H)
200 in. (160⬙ W ⳯ 120⬙ H)
150 in. (120⬙ W ⳯ 90⬙ H)
100 in. (80⬙ W ⳯ 60⬙ H)
80 in. (64⬙ W ⳯ 48⬙ H)
60 in. (48⬙ W ⳯ 36⬙ H)
40 in. (32⬙ W ⳯ 24⬙ H)
Picture size: 100 inches (254 cm)
ⳮ25.4 in. (ⳮ64.6 cm)
ⳮ20.4 in. (ⳮ51.7 cm)
ⳮ15.3 in. (ⳮ38.8 cm)
ⳮ10.2 in. (ⳮ25.8 cm)
ⳮ7.6 in. (ⳮ19.4 cm)
ⳮ5.1 in. (ⳮ12.9 cm)
ⳮ4.1 in. (ⳮ10.3 cm)
ⳮ3.1 in. (ⳮ7.8 cm)
ⳮ2.0 in. (ⳮ5.2 cm)
242.2 in. (615.1 cm)
193.7 in. (492.1 cm)
145.4 in. (369.2 cm)
96.9 in. (246.1 cm)
72.7 in. (184.6 cm)
48.5 in. (123.1 cm)
38.8 in. (98.5 cm)
29.1 in. (73.9 cm)
19.4 in. (49.3 cm)
Screen
Lens center
Upper lens
shift portion
H: 48.5 inches
(123.1 cm)
Upper lens shift position
(High mount setup)
Lens center
Lower edge of screen
(white portion) = Standard (0) point
Lower lens shift position
(Desktop setup)
Lower lens shift portion H: ⳮ5.1 inches (ⳮ12.9 cm)
• Ceiling Mount
When the projector is in the inverted position, use the
upper edge of the screen as the base line, and exchange the lower and upper lens shift values.
–H
High edge of screen
90˚
Note:
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level. Tilting or angling the
projector will reduce the effectiveness of the lens shift function.
E-10
Using the Image Invert/Reverse Function
■ This projector is equipped with an image invert/reverse function. The projected image can be
inverted or reversed by using the MENU button and the ADJUSTMENT / and / buttons.
1
1. Press the MENU button.
IMAGE
ADJ.
BLK SCRN DISP
INPUT DISPLAY
REVERSE
INVERT
:SEL.
:ADJ.
[OFF]
[OFF]
[OFF]
[OFF]
MENU : E N D
2
2. Reversed Image Mode
.JDA
]FFO[
]FFO[
]NO[
EGAMI
PSID NRCS KLB
YALPSID TUPNI
ESREVER
TREVNI
]FFO[
D N E : UNEM
In the IMAGE ADJ. menu, press the ADJUSTMENT /
buttons to select “REVERSE”. Then press the ADJUSTMENT / buttons to select ON. The reversed image will
appear.
.LES:
.JDA:
3
3. Inverted Image Mode
MENU : E N D
BLK SCRN DISP
INPUT DISPLAY
REVERSE
INVERT
4. Reversed Inverted Image Mode
[OFF]
[OFF]
[OFF]
ADJ.
MENU : E N D
In the IMAGE ADJ. menu, set the REVERSE and INVERT
functions to ON. The reversed inverted image will appear.
INVERT
REVERSE
INPUT DISPLAY
BLK SCRN DISP
IMAGE
In the IMAGE ADJ. menu, press the ADJUSTMENT /
buttons to select “INVERT”. Then press the ADJUSTMENT / buttons to select ON. The inverted image will
appear.
IMAGE
[ON]
:ADJ.
:SEL.
:SEL.
:ADJ.
4
With the MENU screen displayed, press the ADJUSTMENT / buttons to select “IMAGE ADJ”. Then press the
ENTER button to display the IMAGE ADJ. screen.
• The last MENU screen selected is indicated for about
30 seconds.
[ON]
[ON]
[OFF]
[OFF]
ADJ.
5. Press the MENU button anytime to exit
IMAGE ADJ.
E-11
How to set up the projector and screen
Cautions: When setting up the projector
• For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in
an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments,
the lens and filter must be cleaned more often. Periodically the filter should be replaced and the projector should
be cleaned internally. As long as the projector is properly maintained in this manner, use in these environments
will not reduce the overall operation life. Please note that all internal cleaning must be performed by an Authorized Sharp Industrial LCD Products Dealer or Service Center.
• Do not expose to extreme heat or cold.
Operating temperature: 41°F to 104°F (+5°C to +40°C)
Storage temperature: ⳮ4°F to 140°F (ⳮ20°C to +60°C)
• Do not tilt the projector more than 5°.
■ Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out
colors, making viewing difficult. Close the curtains and dim the lights when using the screen in a bright or sunny
room.
■ The best picture will be obtained when the projector is at a 90 degree angle to the screen. Position the projector
and screen as shown.
Example of a standard setup
TOP VIEW
SIDE VIEW
Lens center
Lens center
If the projector and screen are not
centered properly, the picture will be
distorted, making viewing difficult.
The projector lens should be centered
in the middle of the screen.
■Using the horizontal reverse function makes the following setups possible.
Example of a reversed image setup
• By placing a mirror (normal flat type) in front of the lens and using the horizontal reverse function, the image
reflected from the mirror can be projected onto the screen.
• Rear projection with a rear projection screen is also possible when using the horizontal reverse function.
Rear Projection
▼
▼
AUDIENCE SIDE
Mirror
The projector lens should be centered
in the middle of the screen.
If the projector and screen are not
centered properly, the picture will be
distorted, making viewing difficult.
E-12
Example of a high-mount setup
• A high-mount setup makes projection from an elevated location possible, without ceiling modifications.
TOP VIEW
SIDE VIEW
Lens center
Lens center
Example of a ceiling-mount setup
Before mounting the projector, be sure to contact your nearest Authorized Sharp Industrial LCD Products Dealer to
obtain the manufacturer recommended ceiling mount bracket (sold separately). (AN-XGCM20 Ceiling Mount
Bracket, AN-EP101AP Extension Tube).
TOP VIEW
SIDE VIEW
90˚
Lens center
Lens center
• If the relative positions of the projector and the screen are not properly adjusted, the picture will be distorted.
Note:
• A polarizing screen cannot be used with this projector.
Inverted Labeling for Ceiling Mount
• When ceiling mounting the projector, attach the supplied inverted label as shown.
Front
OFF
LAMP
ON
TEMP.
➡
TEMP.
➡
LAMP
POWER
OFF
ON
TEMP.
POWER
LAMP
POWER
ON/OFF
ON/OFF
ON/OFF
Terminal Cover
• When the projector is ceiling mounted, attach the terminal cover
(supplied) to hide the connecting cables.
• Use the terminal cover to hide the connecting cables when the
projector is used on a desktop or high mounted.
E-13
Adjusting the Height of the Picture
■ When adjustments for the projector position cannot be made using the Lens Shift alone, or when the projector
stand is on an angle, use the adjuster release to adjust the vertical angle of the projector. Minor adjustments can
be made with the adjusters.
Adjuster release
Adjusters
1. Press the adjuster release and lift the
projector to the desired angle with both
hands.
1
• The adjuster legs will extend to the surface of the table.
2. Remove your hand from the adjuster
release.
2
• The adjuster legs will lock in position. Release the
projector once you are sure the adjuster legs have
locked in position.
3. Make any minor adjustments necessary.
3
• Turn the adjusters to further adjust the angle of the
projector.
Returning the projector to its original position
• While holding the projector with both hands, press the
adjuster release and slowly lower the projector to its
original position.
Notes:
• Adjustable up to approximately 5° from the horizontal.
• When adjustments are made with the adjusters, the picture may
become distorted, depending on the relative positions of the projector
and the screen.
• After adjusting, in some cases, all of the adjuster legs may not be
resting on the table.
To prevent the projector from wobbling, adjust the adjuster legs so that
they firmly contact the table.
Cautions:
• Do not press the adjuster release when the adjuster legs are extended
without firmly holding the projector.
• When lowering the projector, be careful not to get your fingers caught
in the area between the adjusters and the projector.
• Do not hold the lens when lifting or lowering the projector.
Transporting the Projector
Use the carrying handle when carrying the projector.
When transporting the projector, carry it by the handle located on the side
of the unit.
Note:
• Always put on the lens cap to prevent damage to the lens when transporting the projector.
Carrying handle
Caution:
• Do not lift or carry the projector by the lens or the lens cap as this may
damage the lens.
E-14
Connecting the Projector (VIDEO 1, VIDEO 2)
■ To watch video playback with the projector connected to audio/video output equipment, such
as a VCR, or Laser Disc Player or DVD Player or to view on a separate monitor, make the
following connections.
• Always turn off the LCD Projector while connecting to video equipment, in order to protect both the projector and
the equipment being connected.
➔
Used when the AV equipment
to be connected has an SVIDEO output terminal.
Playback
To
audio
output
terminals
To
S-video
output
terminal
VCR
To
video
output
terminal
To
video
output
terminal
To
audio
output
terminals
To
video
input
terminal
To
audio
input
terminals
Video equipment
Monitor
■ Select either VIDEO 1 or VIDEO 2 to output the images to the monitor.
■ Note the following when using the S-VIDEO INPUT terminal:
• The S-VIDEO INPUT terminal uses a video signal system in which the picture is separated into a color and a
luminance signal to realize a higher-quality picture.
• The S-VIDEO INPUT terminal has priority over the VIDEO INPUT 1 terminal. Make the audio connection via the
AUDIO INPUT terminals (left/right).
E-15
Connecting the Projector (RGB 1, 2: Computer)
• Please carefully read the manual of the computer you will be connecting.
• Before connecting, be sure to turn both the projector and the computer off. After making
all connections, turn the projector on first. The computer should always be turned on last.
To display input terminal
To RS-232C terminal
15-pin
D-Sub
9-pin D-Sub
6-pin DIN
Mouse Control Cable for IBM
PS/2 (Supplied)
4-pin DIN
Mouse Control Cable
for Macintosh Series
(Supplied)
RGB
Switcher
(Sold
separately)
Macintosh
Adaptor
(Supplied)
9-pin D-Sub
9-pin D-Sub
Mouse Control
Cable (Supplied)
15-pin
D-Sub
RGB Signal Cable (Supplied)
BNC 5 Cable (Sold separately)
Audio Cable for Personal Computer (Sold separately)
• You can connect your projector to a computer for easy projection of full color computer images and an external
monitor for simultaneous viewing. See pages 17 and 18 for details of the connections.
• Refer to page 20 for a list of personal computers connectable to the projector. Use with computers other than
those listed may cause some of the functions not to work.
• When the RS-232C terminal on this unit is connected to a personal computer via an RS-232C cable (cross type),
the personal computer can control the projector and the status of the projector can be checked. See pages 34 and
35 for details.
• By connecting the projector mouse terminal to your personal computer’s mouse terminal, using the supplied
mouse control cables, you can use the remote control in place of the computer’s mouse. Refer to page 8 for
details.
Notes:
• The wireless mouse or RS-232C function may not operate if your computer port is not correctly set-up. Please refer to your
computer owners manual for details on setting-up/installing the correct Mouse Driver.
• Do not connect or remove the mouse control cable or RS-232C cable to/from your computer while it is on. This may damage
your computer.
• Do not connect to the mouse input terminal for IBM/Mac and mouse input terminal for PC98 simultaneously.
“Plug And Play” Function
This projector is compatible with VESA DDC 1 and DDC 2B standards. This projector and a VESA DDC compatible
computer will communicate their setting requirements, allowing for quick and easy set-up.
Notes:
• The “plug and play” function cannot be used with RGB 2 input.
• The DDC, “plug and play” function of this projector is only functional when used in conjunction with a VESA DDC compatible
computer.
E-16
Connecting to the Computer RGB Input (RGB 1)/Output (RGB 1, 2) Terminals
■ You can connect your projector to a computer for easy projection of full-color computer images, and an external
monitor for simultaneous viewing.
■ Use the RGB 1 input connector and the supplied RGB cable for Plug & Play.
1
Side view of the projector
INPUT1
COMPUTER
OUTPUT
RGB
RGB Signal
Input Socket
1. Connecting to an IBM-PC (VGA, SVGA,
XGA, SXGA) Series computer – 1,280 ×
1,024 maximum resolution
Plug the RGB signal cable correctly into the RGB INPUT
terminal on the projector and into the RGB signal output
terminal on the computer, and secure the plugs by
tightening the thumb screws.
ANALOG RGB OUT
RGB Signal
Cable
(Supplied)
21
IBM-PC (VGA,
Note:
SVGA, XGA,
• This connection is possible only when using a computer with a VGA/
SXGA)
SVGA/XGA/SXGA or Mac display output port.
Series (computer)
RGB Signal
Output Socket
Macintosh Adaptor (Supplied)
ON
↑
↓
OFF
2
Macintosh Adaptor (Supplied)
Macintosh
OG
AL
AN
B
RG
T
OU
2. Connecting to a Macintosh Series
Computer
• 640 × 480, 832 × 624 or 1,024 × 768 resolution
1 Set the proper switches on the supplied adaptor.
• For 640 × 480 resolution, set switches 1 and 2 to
“ON” and 3, 4, 5 and 6 to “OFF”.
• For 832 × 624 resolution, set switches 2 and 4 to
“ON” and 1, 3, 5 and 6 to “OFF”.
• For 1,024 × 768 resolution, set switches 2 and 3 to
“ON” and 1, 4, 5 and 6 to “OFF”.
2 Connect the supplied Macintosh adaptor to the RGB
signal output terminal on your Macintosh Series
computer, as shown on the left, and secure the plugs
by tightening the thumb screws.
RGB Signal
Output Socket
3
3 Firmly plug the supplied RGB signal cable into both
the RGB input terminal on the projector and the
Macintosh adaptor on the computer, and secure the
plugs by tightening the thumb screws.
Side view of the projector
INPUT1
RGB Signal
Input Socket
COMPUTER
RGB
OUTPUT
Macintosh
RGB Signal
Output Socket
ANALOG
RGB OUT
RGB Signal
Cable
(Supplied)
E-17
Notes:
• Be sure to use the supplied Macintosh adaptor.
• Be sure the switches on the adaptor are properly set.
• Once the adaptor is connected to a computer and the computer is
turned on, the display mode cannot be changed even if the switches
on the adaptor are reset.
• The supplied adaptor is only for use with H-SYNC and
V-SYNC output. When connecting a Macintosh Series computer that
only outputs C-SYNC, use a special C-SYNC output adaptor (sold
separately).
3. Connecting to other compatible
computers
When connecting the projector to a compatible computer
other than an IBM-PC (VGA/SVGA/XGA/SXGA) or
Macintosh series, a separate cable is needed. Please
contact your dealer for ordering information.
Notes:
• Connecting computers other than the recommended types may result
in damage to the projector, the computer, or both.
• Connect the audio from the computer to the COMPUTER AUDIO
INPUT terminal.
4. Connecting to the COMPUTER AUDIO
INPUT
4
• The COMPUTER AUDIO INPUT accepts COMPUTER RGB
input.
• Connect a 3.5 mm Stereo Minijack-RCA L/R cable (not
included) from the audio output terminal on the computer to
the COMPUTER AUDIO IN terminal on the projector.
5
5. Connecting an external monitor
INPUT1
COMPUTER
RGB
OUTPUT
Optional Macintosh
adaptor cable
Direct
connection
U.S.A. ONLY
or
External IBM-PC
monitor
External Macintosh
monitor
Connect your computer monitor to the projector’s COMPUTER RGB OUTPUT terminal to view images simultaneously on the external monitor and the projection
screen. Select either RGB 1 or RGB 2 to output the
images to the monitor.
Caution (Apple Macintosh):
Do not connect the COMPUTER RGB OUTPUT to any
monitor except the following:
Apple Color RGB Monitor 13⬙/14⬙ (640 × 480),
16⬙/17⬙ (832 × 624) or 19⬙ (1,024 × 768)
The output signal from the projector to the monitor should be
the same as the input signal from the computer to the
projector.
Example: Input 13⬙/14⬙ (640 × 480) → Output (640 × 480)
Input 16⬙/17⬙ (832 × 624) → Output (832 × 624)
Input 19⬙ (1,024 × 768) → Output (1,024 × 768)
Note:
• The supplied adaptor is only for use with H-SYNC and V-SYNC output. No
picture will appear when connected to monitors that only use C-SYNC.
Notes:
• When using the projector with an external IBM-PC monitor, connect
the monitor using the supplied cable. When using the projector with a
Macintosh monitor, an optional adaptor cable is required. Before using
any other type of monitor, carefully check the monitor’s interface
specifications and make sure that they match the specifications of the
projector’s interface.
• The external monitor output will only display an analog computer input
signal. It will not display a digital or video input signal. To split the
composite video signal, use a video distribution amplifier. This is
available from your local dealer. The computer RGB output will only
loop through the same signal connected to the computer RGB input.
(VGA IN → VGA OUT, Mac IN → Mac OUT)
E-18
Connecting the Projector (RGB 2)
Connecting to the Computer RGB 2 Input Terminals
■ Prevents a deterioration of picture quality to enable 5 BNC computer input.
• Before connecting, be sure to turn both the projector and the equipment off.
• Connect the R, G/G-SYNC, B, H/C-SYNC and V-SYNC cables to the correct input terminals on the projector and
an RGB switcher (sold separately) connected to the computer, or connect a 5 BNC-VGA cable (sold separately)
directly from the input terminals on the projector to the computer.
Side terminals
➞
• COMPUTER AUDIO
INPUT accepts
COMPUTER RGB 1
and 2 input.
• Use INPUT SELECT
to choose the
correct setting.
Playback
3.5 mm Stereo Minijack
to RCA L/R cable (Sold
separately)
To R, G/G-SYNC, B,
H/C-SYNC and V-SYNC
output terminals
To RGB Switcher
(Sold separately)
To audio output terminal
RGB
Switcher
Note:
• When connecting a Macintosh Series computer that outputs C-SYNC, connect the cable to the COMPUTER RGB 2 INPUT
H-SYNC input terminal.
E-19
Input Signals (Recommended Timing)
For IBM and compatibles
For Apple Macintosh Series
Input signals: The video output signal timing of different
types of video signals are shown below
for reference.
VIDEO SIGNAL
HORIZONTAL
SYNC SIGNAL
a
a
b
c
e = 2 dot
d
d
C-SYNC (V)
VERTICAL
SYNC SIGNAL
w
w
y
x
x
y
z
V-SYNC
z
IB M
IB M
I BM
IB M
IB M
IB M
IB M
IB M
IB M
IB M
IB M
VG A
VESA
S V GA
SVGA
S VG A
SV G A
XGA
XGA
XGA
SXGA
SXGA
V ES A
S ta n d a r d
V ES A
S ta n d a r d
V ES A
S ta n d a r d
V ES A
S ta n d a r d
Text
G r a p h ic
G raphic
Graphic
V ES A
G u id e lin e
VE S A
S ta n d a r d
VESA
St andard
V ES A
G u id e lin e
720 dots
640 dots
640 dots
800 dots
800 dots
800 dots
800 dots
1,024 dots 1,024 dots 1,024 dots 1,280 dots 1,280 dots
350 lines 400 lines 350 lines 400 lines 480 lines 480 lines
600 lines
600 lines
600 lines
600 lines
MOD E
768 lines
768 lines
768 lines 1,024 lines 1,024 lines
A p p le
A p p le
A p p le
A p p le
MacintoshTM MacintoshTM
MacintoshTM MacintoshTM
IIsi
LC
1 3 " M o n ito r
1 3 " M o n it o r
640 dots
640 dots
1 6 " M o n i to r 1 9 " M o n i to r
832 dots
1,024 dots
480 lines
480 lines
624 lines
768 lines
LE V E L
0 .7 V p - p
75 Ω load
0 .7 V p - p
0 .7 V p - p
0.7Vp-p
0 .7 V p - p
0 .7 V p - p
0 .7 V p - p
0 .7 V p - p
0 .7 V p - p
0.7Vp-p 1Vp-p max. 0.7Vp-p max. 0.7Vp-p max. 0.7Vp-p max.
0 .7 V p - p
75Ω load
75Ω load
75Ω load
7 5 Ω lo a d 7 5 Ω lo a d 7 5 Ω lo a d 7 5 Ω l o a d 7 5 Ω lo a d 7 5 Ω lo a d 7 5 Ω lo a d 7 5 Ω lo a d 7 5 Ω lo a d 7 5 Ω lo a d 7 5 Ω lo a d
TYPE
R•G•B
R•G•B
V ID E O
R•G•B
R•G•B
R•G•B
R•G•B
R•G•B
R•G•B
R•G•B
R•G•B
R•G•B
R•G•B
C .S Y N C
R•G•B
C.SYNC
R•G•B
C .S Y N C
R•G•B
C .S Y N C
35
F R O N T P O R CH
a
do t
17
14
24
24
40
56
16
24
24
16
48
16
64
78
31
S Y NC
b
do t
10 8
96
40
72
128
120
80
136
13 6
96
112
144
64
62
65
96
B AC K P O R CH
c
do t
55
50
128
1 28
88
64
160
160
14 4
17 6
248
248
96
11 6
2 24
173
V ID E O P E R IO D
d
do t
72 0
640
64 0
8 00
800
800
800
1 ,0 2 4
1 ,0 2 4
1 ,0 2 4
1,280
1,280
64 0
64 0
8 32
1,024
do t
90 0
800
83 2
1 ,0 2 4
1 ,0 5 6
1, 040
1 ,0 5 6
1 ,3 4 4
1 ,3 2 8
1 ,3 1 2
1,688
1,688
86 4
89 6
1 ,1 5 2
1,328
µs
3 1 .7 7 7 4
31. 777 6
2 6 .4 1 3
2 8 .4 4 4
2 6 .4 0 0
2 0 .8 0 0
2 1 .3 3 3
2 0 .6 7 7
1 7 .7 0 7
1 6 .6 6 0
15.6
12.5
2 8 .5 7 1 4
2 8 .5 9 5
2 0 .1 2 4
16.650
1 dot
ns
3 5 .3 0 8 2
39. 721 9
3 1 .7 4 6
2 7 .7 7 7
2 5 .0 0 0
2 0 .0 0 0
2 0 .2 0 2
1 5 ,3 8 5
1 3 .3
1 2 .7
9.3
7.4
3 3 .0 6 8 8
3 1 .9 1 4 0 6 3
1 7 .4 6 8
12.538
1/ H
kH z
3 1 .4 6 8 9
31. 468 8
3 7 .8 6 0
3 5 .1 5 6
3 7 .8 7 9
4 8 .0 7 7
4 6 .8 7 5
4 8 ,3 6 3
5 6 .4 7 6
6 0 .0 2 3
63.981
79.976
3 5 .0 0 0 0
3 4 .9 7 1 1 4 9
4 9 .6 9 3
60.0
1/ dot
M Hz
2 8 .3 2 2
2 5 .1 7 5
3 1 .5 0 0
3 6 .0 0 0
4 0 .0 0 0
5 0 .0 0 0
4 9 .5 0 0
6 5 .0 0 0
7 5 .0
7 8 .7 5
108.000
135.000
3 0 .2 4 0 0
3 1 .3 3 4 1 4 9
5 7 .2 4 6
79.76
1H (a+ b+ c + d)
TTL
TTL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
+/–
+
–
+
–
–
–
+ /–
+
+
+
–
–
+
+
+
–
–
–
–
3
LE VE L
S Y N C P O L A R IT Y
V
S
Y
N
C
b c
VIDEO SIGNAL
VIDEO SIGNAL
H
S
Y
N
C
e
C-SYNC (H)
VIDEO SIGNAL
TTL
F R O N T P O R CH
w
H
38
13
38
13
11
9
1
1
37
1
3
3
1
1
1
3
3
1
S Y NC
x
H
2
2
2
2
2
3
2
4
6
3
6
6
3
3
3
3
3
3
3
B AC K P O R CH
y
H
59
34
59
34
32
28
22
23
23
21
29
29
28
38
38
39
39
39
30
V ID E O P E R IO D
z
H
3 50
400
350
400
480
480
6 00
600
600
600
768
76 8
76 8
1,024
1,024
48 0
48 0
6 24
768
H
4 49
449
449
449
525
520
6 25
628
666
625
806
80 6
80 0
1,066
1,066
52 5
52 5
6 67
804
ms
1 4 .2 6 8 1
1 4 .2 6 8 1
1 4 .2 6 8 1
14. 268 1
1 6 .6 8 3 2
1 3 .7 3 5
1 7 .7 7 8
1 6 .5 7 9
1 3 .8 5 3
1 3 .3 3 3
1 6 .6 6 6
1 4 .2 7 2
1 3 .3 2 8
16.7
16.7
1 5 .0 0
1 5 .0 0
1 3 .4 2 3
13.387
Hz
7 0 .0 8 6 6
7 0 .0 8 6 6
7 0 .0 8 6 3
70. 086 3
5 9 .9 4 0 5
7 2 .8 0 9
5 6 .2 5 0
6 0 .3 1 7
7 2 .1 8 8
7 5 .0 0 0
6 0 .0 0 6
7 0 .0 6 9
7 5 .0 2 9
60.020
75.025
6 6 .6 7
6 6 .6 7
7 4 .5 0 2
74.70
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
T TL
–
+
–
+
–
–
+/–
+
+
+
–
–
+
+
+
–
–
–
–
1V (w + x+ y + z)
1/ v
LE VE L
S Y N C P O L A R IT Y
+/–
Notes:
• When connecting a notebook computer to the data-projector for display on an (800 × 600) LCD screen, the screen may not
show a full picture image. See page 22, “Computer Mode Memory Adjustments” for details.
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. If this occurs,
turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change
display modes can be found in your notebook computer’s operation manual.
E-20
RGB Adjustment Controls
■ When displaying computer patterns which repeat every other dot (tiling, vertical stripes, etc.),
interference may occur between the LCD pixels, causing flickering, vertical stripes, or contrast
irregularities in portions of the screen. Should this occur, use the ADJUSTMENT / buttons
for HORIZONTAL (LEFT/RIGHT) and VERTICAL (UP/DOWN) position adjustments to adjust
for the optimum picture.
RGB Input Adjustments (CLOCK, PHASE, V-POS and
H-POS)
1. Select RGB 1 or 2 with the INPUT SELECT button and press
the MENU button to select the RGB INPUT ADJ. mode.
With the MENU screen displayed, press the ADJUSTMENT / buttons to select
“RGB1 INPUT ADJ.” Then press the ENTER button to display the RGB1 INPUT
ADJ. screen.
2
RGB1
INPUT
ADJ.
CLOCK
PHASE
H-POS
V-POS
MODE
RESET
MEMORY SELECT
:SEL.
:ADJ.
0
0
0
0
-
+
+
+
+
2. Select the item you wish to adjust with the ADJUSTMENT
/ buttons. Adjust the item with the ADJUSTMENT /
buttons.
[OFF]
ENTER : N E X T
MENU : E N D
Note:
• To display only the item that you want to adjust, press the ENTER button after selecting the item
with the ADJUSTMENT / buttons. Then adjust the item with the ADJUSTMENT / buttons.
3. Press the MENU button anytime to exit RGB INPUT ADJ.
Description of Adjustment Items
CLOCK SPEED ADJUSTMENT (FAST/SLOW)
• Adjust the input signal horizontal frequency and the dot clock so that the screen display is normal.
PHASE ADJUSTMENT (UP/DOWN)
• Used to reduce image distortion or improve contrast.
HORIZONTAL POSITION ADJUSTMENT (LEFT/RIGHT)
• Used to center the on-screen image by moving it to the left or right.
VERTICAL POSITION ADJUSTMENT (UP/DOWN)
• Used to center the on-screen image by moving it up or down.
MODE ADJUSTMENT
Connecting to IBM-PC Computers
• Ordinarily, the type of input signal is detected and the correct resolution mode (Text or
Graphics) is automatically selected. However, for the following signals, set MODE to ON or
OFF to select the projector’s resolution mode to match the computer display mode properly.
720 dots × 400 lines, 720 dots × 350 lines (Text Mode)
640 dots × 400 lines, 640 dots × 350 lines (Graphic Mode)
• For graphic mode, select MODE and set the MODE to ON.
• For text mode, select MODE again at this time, and set MODE to OFF.
Connecting to Macintosh LC/II Series Computers
• When connecting to a Macintosh II with 35 kHz Dot Frequency, select MODE and set MODE
to ON.
• When connecting to a Macintosh LC Series computer with 34.97 kHz Dot Frequency, set
MODE to OFF.
• When connecting to third party video cards and other Macintosh computers, set MODE to
ON or OFF to select the correct display mode.
• When the input signal is automatically detected or when there is no input signal, MODE (---)
appears on the screen and the display mode cannot be changed.
INITIAL RESET
• To return the H-POS, V-POS, PHASE and CLOCK adjustments to their initial settings, select
RESET and then press the ENTER button.
MEMORY SELECT
• Used to store up to seven computer mode adjustments.
INPUT ADJUSTMENT
FILTER
ON
1
OFF
E-21
1 Filter switch
In the case of very detailed computer patterns which repeat every other dot (tiling, vertical
stripes, etc.), noise may appear on the screen. Should this occur, set the FILTER switch to ON.
The pattern area will balance, and the noise will be reduced.
Note:
• Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering
may occur, making the picture hard to see.)
Computer Mode Memory Adjustments
• The projector has been preset with different modes for
use with SVGA and other compatible computers.
However, 7 memory positions are provided to store
mode adjustments.
• Each memory position can be used to store mode
adjustments to match the computer.
1. Press the ENTER button to select the
Memory Adjustment mode.
1 When RGB 1 or 2 is selected.
RGB1
:SEL.
INPUT ADJ.
CLOCK
PHASE
H-POS
V-POS
MODE
RESET
MEMORY SELECT
RGB1 ADJ.
RGB1 INPUT ADJ.
IMAGE ADJ.
AUDIO
SYSTEM SETUP
LANGUAGE
:SEL.
ENTER : N E X T
MENU : E N D
0
0
0
0
-
+
+
+
+
[OFF]
ENTER : N E X T
MENU : E N D
• Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT / buttons to
select “RGB1 INPUT ADJ.” Press the ENTER button.
The MENU mode changes as shown.
• While the RGB INPUT adjustment menu is displayed,
press the ADJUSTMENT / buttons to select
“MEMORY SELECT”. Then press the ENTER button to
change the image.
2. Press the ADJUSTMENT
2
MEMORY SELECT
MEMORY SELECT
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
/
buttons.
• The screen shown on the left will appear. There are 7
memory positions.
STANDARD SETTING
SETTING
SETTING
:SEL.
:ADJ.
:SEL.
ENTER : E N T E R
MENU : E N D
MEMORY SELECT
MEMORY SELECT
0
1
2
3
RESOLUTION
HOR FREQ
VERT FREQ
SETTING
:SEL.
:ADJ.
4
ENTER : B A C K
MENU : E N D
5
6
7
1024×768
6 0 . 0 KHz
7 5Hz
ENTER : E N T E R
MENU : E N D
0
1
2
3
4
5
NON
SETTING
:SEL.
:ADJ.
ENTER : E N T E R
MENU : E N D
6
7
• Press the ADJUSTMENT button once to move to the
following screen. Press the ADJUSTMENT / buttons
to select the number of the memory you want to adjust.
If that memory position has not been set, the screen on
the right will be displayed. If it has been set, the screen
on the left will be displayed. MEMORY No.0 cannot be
set. It contains the fixed factory preset settings.
• To make or change a setting, press the ADJUSTMENT
/ buttons to move the cursor to “SETTING.” Then
press the ENTER button to go to the RGB INPUT
adjustment menu screen. (If you do not want to make
any adjustments, press the MENU button.)
• Select the item you want to adjust by pressing the
ADJUSTMENT / buttons, then use the
ADJUSTMENT / buttons to make the adjustments.
When adjustments are completed, press the MENU
button. The display disappears and the adjustments are
stored in memory as a user mode. See page 21 for
details on the adjustment items.
3. Press the MENU button anytime to exit
RGB INPUT ADJ.
E-22
Basic Operation of the Projector
1
1. Connect the AC cord.
A.C.120V
C.A.120V
Connect the supplied AC cord to the AC inlet on the side
of the projector .
ON
OFF
1
2
AC cord
MAIN
POWER
switch
2. Turn on the MAIN POWER.
2
ON/OFF
ON
POWER
OFF
LAMP
When the MAIN
POWER is on, the
POWER indicator
lights red.
Press the MAIN POWER switch on the side of the projector. The POWER indicator lights red and the projector
enters STANDBY mode.
TEMP.
3
Projector
ON/OFF
ON/OFF
Remote control
ON/OFF
ON
OFF
ON/OFF
POWER
LAMP
TEMP.
When the power is on, the LAMP
REPLACEMENT indicator flashes
to show the operating condition of
the lamp.
Green:
Lamp is ready
Flashing green: Warming up
Red:
Change bulb
3. Turn on the POWER.
Press the POWER ON/OFF button on the projector or the
POWER ON button on the remote control.
• When the power is turned off by pressing the POWER
ON/OFF button, the POWER indicator will not turn off
until the fan has stopped running.
• See page 32, “Lamp/Maintenance Indicators” for
details.
Notes:
• When the POWER indicator is not lit, the remote control cannot be
used to operate the projector.
• If the power is turned on immediately after it has been turned off, it
may take a short while before the lamp turns on. (During this period
the LAMP REPLACEMENT indicator flashes.)
• After the projector is unpacked and turned on for the first time, a slight
odor may be emitted from the exhaust fan. This odor will soon
disappear with use.
Caution:
• Be sure to take off the lens cap before operation of the projector. Do
not place the lens cap on the lens during operation. The lens cap may
become extremely hot.
E-23
4
4. Select one of eight ON-SCREEN DISPLAY
languages.
On-Screen Display
LANGUAGE
You can return to the previous screen by selecting the
uppermost item (turquoise) with the ADJUSTMENT /
buttons (in this case, LANGUAGE) and then pressing
the ENTER button.
ENGLISH
DEUTSCH
ESPAÑOL
NEDERLANDS
FRANÇAIS
ITALIANO
SVENSKA
:SEL.
The on-screen display is set to English at the factory. The
language for the unit’s ON-SCREEN DISPLAY can be set
to English, German, Spanish, Dutch, French, Italian,
Swedish or Japanese.
ENTER : E N T E R
MENU : E N D
Setting the ON-SCREEN DISPLAY language
1) Press the MENU button. The menu will appear on the
screen.
2) Press the ADJUSTMENT / buttons to highlight the
LANGUAGE item yellow. Then press the ENTER button to
display the language menu.
3) Press the ADJUSTMENT / buttons to highlight the
desired language yellow. Then press the ENTER button to
set the language. The ON-SCREEN DISPLAY is now
programmed to display in the language chosen.
5
5. Change the system mode.
On-Screen Display
IMAGE
BLUE SCREEN
BLK SCRN DISP
INPUT DISPLAY
SYSTEM
REVERSE
INVERT
:SEL.
ENTER : N E X T
MENU : E N D
The video input system mode is set to AUTO at the
factory, but it can be changed to a different mode if the
selected system mode is not compatible with the connected audiovisual equipment (when a color image
appears in black and white, etc.).
SYSTEM
ADJ.
[ON]
[OFF]
[OFF]
[OFF]
[OFF]
➞
AUTO
PAL
SECAM
NTSC 4.43
NTSC 3.58
:SEL.
ENTER : E N T E R
MENU : E N D
1)
2)
3)
4)
Press the MENU button. The menu will appear on the
screen.
Press the ADJUSTMENT / buttons to highlight the
“IMAGE ADJ.” yellow. Then press the ENTER button to
display the IMAGE ADJ.
Press the ADJUSTMENT / buttons to highlight SYSTEM
yellow. Then press the ENTER button to display the
SYSTEM.
Press the ADJUSTMENT / buttons to highlight yellow the
video system desired yellow. Then press the ENTER button
to set the system.
Notes:
• In AUTO mode, “PAL,” “SECAM”, “NTSC 4.43” or “NTSC 3.58” is
displayed on the screen for a few seconds when the mode is changed
with the INPUT SELECT button.
• When the system mode is set to AUTO, you may not receive a clear
picture due to signal differences. If this happens, switch to the color
system you are viewing.
E-24
6
On-Screen Display
For viewing the picture from a
video source connected to: VIDEO
INPUT 1 or S-VIDEO INPUT
VIDEO INPUT 2
6. Select input.
Press the INPUT SELECT button on the projector to
switch the picture input. When you press the button, the
current input mode is displayed for about 4 seconds. If
you press the button again while the input mode is
displayed, the mode changes as shown on the left.
Confirm the selected input terminal and press the INPUT
SELECT button.
COMPUTER
RGB1
Notes:
• This can be selected directly using the VIDEO 1, VIDEO 2, DATA 1
and DATA 2 buttons on the remote control.
• In VIDEO mode, the system being received will be indicated below the
“VIDEO” display.
• When selecting RGB mode, the resolution being displayed will be
indicated under “RGB,” as shown on the left. (Refer to the second
example when connecting to Mac display.)
• When no signals are being received, “NO SIGNAL” will be displayed.
When receiving a signal the projector is not preset to receive, “NOT
REG.” will be displayed. (This display function does not operate in
Video mode.)
• The picture size differs in RGB, NTSC, PAL and SECAM INPUT
modes.
COMPUTER
RGB2
Mac
7. Press INPUT CHECK.
7
When the INPUT CHECK button on the remote control is
pressed, the current input mode is displayed for about 4
seconds.
Note:
• The INPUT CHECK button will not function if the INPUT DISPLAY is
turned off, as described on page 30.
Mac
8. Adjust the volume.
8
The number of displayed
segments (0~60) increases
or decreases as the volume
is raised or lowered.
Press the VOLUME UP-DOWN buttons on the projector
or on the remote control to adjust the volume.
MUTE
• Press the MUTE button to temporarily turn off the
sound.
• Press the MUTE button once again to turn the sound
back on.
VOLUME
38
9
9. To turn off the power from the projector
or remote control
TURN
POWER
• Press the POWER ON/OFF button on either the projector or
the remote control. The screen on the left will appear.
• If you want to turn off the power, press the POWER ON/OFF
button on either the projector or the remote control again
within 4 seconds. The power is now temporarily turned off.
• If you accidentally pressed the POWER ON/OFF button and
do not want to turn off the power, wait until the On-Screen
Display disappears before turning the power on again.
O F F ?
YE S : P R E S S
AGA IN
NO : P L E A S E
WA I T
ON/OFF
POWER
LAMP
TEMP.
E-25
The POWER indicator will turn red and the cooling fan will
run for 90 seconds, then the power will turn off, and the
projector will return to STANDBY mode.
The power can be turned on again either from the projector
or remote control. When the power is turned on, the
POWER indicator and LAMP REPLACEMENT indicator
light green.
Note:
• When the MAIN POWER is off on the projector set, the power cannot
be turned on from the remote control.
Adjusting the Picture
• This projector’s picture is factory preset to standard
settings. However, you can adjust it to suit your own
preferences with the ADJUSTMENT buttons on the
projector and the remote control.
• The adjustments can be memorized in RGB 1, RGB 2
or VIDEO separately.
• Four picture modes can be adjusted: “PICTURE,”
“BRIGHT,” “RED,” and “BLUE.”
1
Adjusting the Picture
On-Screen Display
1. Use the MENU button to select the mode
to be adjusted.
RGB1 ADJ.
RGB1 INPUT ADJ.
IMAGE ADJ.
AUDIO
SYSTEM SETUP
LANGUAGE
:SEL.
• When the MENU button is pressed, the MENU mode is
indicated for about 30 seconds. Press the ADJUSTMENT / buttons to select RGB1 ADJ., then press the
ENTER button.
ENTER : N E X T
MENU : E N D
2. Adjust the Picture
2
RGB1
ADJ.
PICTURE
BRIGHT
RED
BLUE
RESET
0
0
0
0
-
+
+
+
+
• Press the ADJUSTMENT / buttons to highlight yellow
the picture adjustment item you want to adjust.
• Press the ADJUSTMENT / buttons to move the “ ”
mark of the selected adjustment item to the desired
setting.
• The adjustment mode is displayed for about 30
seconds.
Description of Adjustment Items
:SEL.
:ADJ.
ENTER : N E X T
MENU : E N D
3
Selected item
ADJUSTMENT
button
ADJUSTMENT
button
PICTURE
For less contrast
For more contrast
BRIGHT
For less brightness
For more brightness
RED
For weaker red
For stronger red
BLUE
For weaker blue
For stronger blue
COLOR
For less color intensity
For more color intensity
TINT
Skin tones become purplish
Skin tones become greenish
SHARPNESS
For less sharpness
For more sharpness
RESET
All RGB Video Adjustment items are returned to the factory preset settings.
Note: To reset all adjustment items, select RESET in
“RGB1 ADJ. ” mode and press the ENTER button.
3. Display only the item to adjust.
PICTURE
:SEL.
:ADJ.
0 -
ENTER : E N T E R
MENU : E N D
+
• Press the ADJUSTMENT / buttons to highlight yellow
the picture adjustment item you want to adjust. If you
press the ENTER button at this time, only the selected
item will be displayed.
• Press the ADJUSTMENT / buttons to move the “ ”
mark of the selected adjustment item to the desired
setting.
• The adjustment mode is displayed for about 30
seconds.
Notes:
• When a VIDEO signal input has been selected, only “PICTURE,”
“BRIGHT,” “COLOR,” “TINT” and “SHARPNESS” can be adjusted.
• TINT only appears in NTSC mode.
4. Press the MENU button anytime to exit
RGB ADJ.
E-26
Adjusting the Audio
• The projector’s audio is factory preset to the standard
setting. However, you can adjust it to suit your own
preference with the ADJUSTMENT buttons on the
projector or the remote control.
• You can adjust the BALANCE, TREBLE and BASS.
• To return to the factory preset mode, press the ADJUSTMENT / buttons to select “RESET”, then press
the ENTER button.
• Press the MENU button to select the normal screen
mode.
Adjusting the Audio
On-Screen Display
AUDIO
BALANCE
TREBLE
BASS
RESET
:SEL.
:ADJ.
0 L
0 0 -
MENU : E N D
R
+
+
• Press the MENU button.
Select “AUDIO” with the ADJUSTMENT / buttons.
Then press the ENTER button to change to the picture
indicated on the left.
• Select “BALANCE,” “TREBLE” or “BASS” with the
ADJUSTMENT / buttons. Adjust the mode you want
with the ADJUSTMENT / buttons.
• To return to the factory preset mode, press the ADJUSTMENT / buttons to select RESET, then press
the ENTER button.
Description of Adjustment Items
E-27
Selected items
ADJUSTMENT
BALANCE
Increased audio from the
left speaker
Increased audio from the
right speaker
TREBLE
Weaker treble
Stronger treble
BASS
Weaker bass
Stronger bass
button
ADJUSTMENT
button
Functions on the Projector
Setting Up the System
■ Using this function, you can check the input signal and
lamp usage time, and select the remote mouse and DC
5V output.
On-Screen Display
SYSTEM
Checking the system and lamp usage time
SETUP
800@600
3 7 . 9 KHz
6 0 Hz
1234H
RESOLUTION
HOR FREQ
VERT FREQ
LAMP USAGE
REMOTE MOUSE
DC 5V OUTPUT
:SEL.
:ADJ.
[AT]
M. PWR
MENU : E N D
• Press the MENU button. Select “SYSTEM SETUP” with the
ADJUSTMENT / buttons. Then press the ENTER button to
change to the picture indicated on the left.
• The current system conditions, including the lamp usage time,
will be displayed on the screen.
• Press the MENU button to select the normal screen mode.
Note:
• In the video screen, the resolution and frequency settings will not be
displayed.
Selecting the Remote Mouse
SYSTEM
SETUP
800@600
3 7 . 9 KHz
6 0 Hz
1234H
RESOLUTION
HOR FREQ
VERT FREQ
LAMP USAGE
REMOTE MOUSE
DC 5V OUTPUT
:SEL.
:ADJ.
[AT]
M. PWR
MENU : E N D
• Press the MENU button.
• Select SYSTEM SETUP with the ADJUSTMENT / buttons.
Then press the ENTER button.
• Select “REMOTE MOUSE” and then select either “[AT]” or
“[98] ”with the ADJUSTMENT / buttons.
• Select [AT] when using IBM compatibles and Apple Macintosh
series.
• Select [98] when using NEC PC98 series (for Japan).
• Press the MENU button to select the normal screen mode.
Selecting DC 5V output
SYSTEM
SETUP
800@600
3 7 . 9 KHz
6 0 Hz
1234H
RESOLUTION
HOR FREQ
VERT FREQ
LAMP USAGE
REMOTE MOUSE
DC 5V OUTPUT
:SEL.
:ADJ.
[AT]
M. PWR
MENU : E N D
• Press the MENU button.
• Select “SYSTEM SETUP” with the ADJUSTMENT /
buttons. Then press the ENTER button.
• Select “DC 5V OUTPUT” and then select either “M.PWR” or
“LAMP” with the ADJUSTMENT / buttons.
• Select “M.PWR” when you want a continuous current supply
from the DC 5V OUTPUT with the main power on.
• Select “LAMP” when you want a current supply from the DC
5V OUTPUT only when LAMP is set to “ON”.
• Press the MENU button to select the normal screen mode.
Background level
• The Background Level adjustment can be used to adjust the
picture white balance for the selected Video Input Source.
• Optimal image quality can be achieved by adjusting the white
portion of the picture to obtain the best color for the selected
source.
VIDEO1 ADJ.
BACKGRND LVL
IMAGE ADJ.
AUDIO
SYSTEM SETUP
LANGUAGE
:SEL.
ENTER : N E X T
MENU : E N D
Adjusting the BACKGROUND LEVEL
BACKGRND LVL
RED
BLUE
RESET
:SEL.
:ADJ.
0 0 -
ENTER : N E X T
MENU : E N D
+
+
• Press the MENU button.
Select “BACKGRND LVL” with the / buttons. Then press the
ENTER button to change the picture as indicated on the left.
• Select “RED” or “BLUE” with the / buttons.
Adjust the mode you want with the / buttons.
• To return to the factory preset mode, press the / buttons to
select “RESET” then press the ENTER button.
• Press the MENU button to select the normal screen mode.
Note:
• To display only the item that you want to adjust, press the ENTER
button after selecting the item with the ADJUSTMENT / buttons.
Then adjust the item with the ADJUSTMENT / buttons.
E-28
LCD Projector
Using the Black Screen Function
■ This projector is equipped with a Black Screen Function. This function can be used to black out the presentation image.
• Press the BLACK SCREEN button on the projector or
the remote control to display the black screen. Press
the BLACK SCREEN button again to return to the
presentation image.
Note:
• When BLK SCRN DISP is set to OFF, the On-Screen Display (“BLACK
SCREEN”) will not appear during black screen. See below.
BLACK SCREEN
On-Screen Display
IMAGE
ADJ.
BLK SCRN DISP
INPUT DISPLAY
REVERSE
INVERT
[ON]
[OFF]
BLACK SCREEN
:SEL.
:ADJ.
E-29
MENU : E N D
[OFF]
[OFF]
Black Screen On-Screen Display
override
■ The On-Screen Display (“BLACK SCREEN”) that
appears during black screen can be turned off. When
BLK SCRN DISP is set to OFF, the On-Screen Display
will not appear during black screen.
• Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT / buttons to
select “IMAGE ADJ.” Then press the ENTER button to
display the IMAGE ADJ. screen as shown. Press the
ADJUSTMENT / buttons to select “BLK SCRN DISP”
and press the ADJUSTMENT / buttons to select ON
or OFF.
On-Screen Display
IMAGE
ADJ.
BLUE SCREEN
BLK SCRN DISP
INPUT DISPLAY
SYSTEM
REVERSE
INVERT
:SEL.
:ADJ.
[ON]
[OFF]
[OFF]
[OFF]
[OFF]
MENU : E N D
On-Screen Display
REMAIN 5M
Notes:
• The Blue Screen Function does not operate in RGB mode.
• When the power is turned off, the POWER indicator will light red.
• To turn the power on again, press the POWER button to set it to OFF,
then press it again to set it to ON.
REMAIN 1M
On-Screen Display
ADJ.
BLK SCRN DISP
INPUT DISPLAY
REVERSE
INVERT
:SEL.
:ADJ.
■ This projector is equipped with a Blue Screen function
that will turn the screen blue when the video input
terminal is not connected to anything, or the video
component is turned off.
• Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT / buttons to
select “IMAGE ADJ.” Then press the ENTER button to
display the IMAGE ADJ. screen as shown. Press the
ADJUSTMENT / buttons to select “BLUE SCREEN,”
and press the ADJUSTMENT / buttons to select ON
or OFF. Press the MENU button to return to the normal
screen.
• When the Blue Screen function is on, the screen will
turn blue when no video signal is being input through
the video input terminal.
• When the Blue Screen function is on, and no video
signal is input via the input terminal for more than 15
minutes, the power is automatically turned off.
• The indicators appear as shown each minute before the
power is turned off, from five minutes before until one
minute before.
REMAIN 4M
IMAGE
Using the Blue Screen Function
MENU : E N D
[OFF]
[OFF]
[OFF]
[OFF]
Using the Input Mode On-Screen
Display Override Function
The On-Screen Displays that appear during input select
(“RGB 1,024 @ 768, 75 Hz,” etc.) can be turned off.
Once INPUT DISPLAY is turned off, the On-Screen
Displays will not appear even if the INPUT CHECK button
on the remote control is pressed.
• Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT / buttons to
select “IMAGE ADJ.” Then press the ENTER button to
display the IMAGE ADJ. screen as shown. Press the
ADJUSTMENT / buttons to select “INPUT DISPLAY,”
and press ADJUSTMENT / buttons to select ON or
OFF.
• When OFF is selected, the On-Screen Display (“RGB
1,024 @ 768, 75 Hz,” etc.) will not be displayed during
input select.
E-30
Air Filter Maintenance
■ The air filter should be cleaned every 100 hours of use. Clean the
filter more often when the projector is used in a dusty or smoky
location.
■ Have your nearest Authorized Sharp Industrial LCD Products Dealer
or Service Center exchange the filter (PFILD0082CEZZ) when it is
no longer possible to clean it.
1. Bottom Air Filter
AIR FILTER cover
Cleaning and Replacing the Filter
1
Turn OFF
the MAIN POWER.
2 Remove
the FILTER COVER.
Press the tab in the
direction of the arrow and
lift open the filter cover.
3 Remove
the AIR FILTER.
Grasp the air filter between
your fingers and lift it out of
the filter cover.
ON
OFF
Turn off the MAIN POWER
switch.
POWER indicator goes off.
Unplug the power cord.
4
Press
Tab
Open
Clean the AIR FILTER.
Clean the dust off the air filter
and cover with a vacuum
cleaner extension hose.
5 Replace the AIR FILTER. 6 Replace
the FILTER COVER.
Place the filter underneath the
tabs on the filter frame.
Return the air filter to its
original position in the filter
cover opening.
Insert the tab on the end of
the filter cover into the filter
cover opening and press the
filter cover into position.
Note:
• Be sure the AIR FILTER COVER is securely installed. The power cannot be turned on unless it is correctly
installed.
2. Side Air Filter
• The side air filter cannot be removed.
• If dust or dirt has collected inside the filter, clean the
filter with a vacuum cleaner extension hose.
AIR FILTER (Not removable)
E-31
Lamp/Maintenance Indicators
Lamp
■ The Lamp has a finite operating life of 1,500 hours. The lamp life may differ, however, depending on the usage environment.
• When the lamp is nearing the end of its operating life, the picture and color quality will deteriorate. When the projector is
turned on after the lamp has been in use for more than 1,400 hours, the LAMP REPLACEMENT indicator will light red and
“LAMP” will flash in yellow on the screen to alert you that it is time to replace the lamp. At this point, take your projector to the
nearest Authorized Sharp Industrial LCD Products Dealer or Service Center to have the lamp replaced.
Note:
The lamp usage time can be checked with the On-Screen display. (See page 28.)
Caution: Once you are alerted that the lamp requires replacement, take your projector to the nearest Authorized Sharp
Industrial LCD Products Dealer or Service Center to have the lamp replaced.
• When the number of hours the lamp has been used reaches 1,500, the power automatically turns off and the projector enters
the standby condition. If you turn on the power after the lamp has been used for 1,500 hours, “LAMP” will flash on screen in
red letters for five minutes and then the power will turn off.
• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.
Maintenance Indicators
ON/OFF
LAMP REPLACEMENT
indicator
POWER
LAMP
TEMPERATURE
indicator
TEMP.
Warning Indicator
TEMPERATURE
indicator
LAMP REPLACEMENT indicator
■ The warning lights on the projector indicate problems inside the projector.
■ There are two warning lights–a TEMPERATURE indicator which warns that
the projector is too hot, and a LAMP REPLACEMENT indicator which lets
you know when to change the lamp.
■ If a problem occurs, either the TEMPERATURE indicator or the LAMP
REPLACEMENT indicator will light up red, and the power will shut off. After
turning off the power, follow the procedures given below.
Symptom
The internal
temperature is
abnormally high.
The lamp does not
light up.
The lamp requires
replacement.
Problem
Possible Solution
• Blocked air intake.
• Relocate projector to a proper location.
• Clogged air filter.
• Clean the filter.
(See page 31.)
• Cooling fan breakdown.
• Clogged air filter.
• Internal circuit failure.
• Take the projector to your nearest Authorized Sharp Industrial LCD Products Dealer
or Service Center for repair.
• Burnt-out lamp.
• Take the projector to your nearest Authorized Sharp Industrial LCD Products Dealer
or Service Center for repair.
• Lamp circuit failure.
• The lamp has been used
for over 1,400 hours.
Notes:
• If the TEMPERATURE indicator comes on, follow the above possible solutions and then wait until the projector has cooled down completely
before turning the power back on. (At least 5 minutes.)
• When the power is turned off and then turned on again, as during a brief rest, the LAMP replacement indicator may be triggered, preventing the
power from going on. When this happens, take the power plug out of the AC outlet and put it back in again.
Before Calling for Service
Problem
No picture and no sound.
Sound is heard but no picture
appears.
Color is faded or poor.
Picture is blurred.
Picture appears but no sound is
heard.
An unusual sound is occasionally heard from the cabinet.
Maintenance indicator lights up.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Check
The projector AC cord is not plugged into the AC wall outlet.
The main power switch is not pressed.
The input is wrong. (See pages 24 and 25.)
Cables improperly connected to side panel of the projector. (See pages 15, 16, 17, 18 and 19.)
Remote control batteries have run down. (See page 7.)
The optional cable for the remote control is improperly inserted.
The main power of the remote control is not turned on.
The remote control’s MOUSE/ADJUSTMENT switch is set to MOUSE.
The lamp has reached the end of its operating life. (See page 32.)
Cables improperly connected to side panel of the projector. (See pages 15, 16, 17, 18 and 19.)
The BRIGHTNESS and PICTURE adjustments are set to minimum position. (See page 26.)
On-Screen Display (“BLACK SCREEN”) is turned off and Black Screen function is turned on, creating
a black image. (See page 29.)
The COLOR and TINT adjustments are not correct. (See page 26.)
Adjust the focus. (See page 9.)
The projection distance is too long or too short to allow for proper focus. (See page 10.)
Cables improperly connected to side panel of the projector. (See pages 15, 16, 17, 18 and 19.)
Volume is set to minimum. (See page 25.)
If the picture is normal, the sound is due to cabinet shrinkage caused by temperature changes. This
will not affect operation or performance.
Refer to “Lamp/Maintenance Indicators” on page 32.
E-32
Connection Pin Assignments
Analog RGB 1 Signal Input and Analog RGB 1 and 2 Output Terminal : 15-pin mini D-sub female connector
5
10
15
1
6
11
Computer Input
Analog
1. Video input (red)
2. Video input (green/sync on
green)
3. Video input (blue)
4. Reserve input 1
5. Composite sync
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. GND
12. Reserve input 2
13. Horizontal sync signal
14. Vertical sync signal
15. Reserve input 3
Analog RGB 2 Signal Input : 5 BNC
Computer Input
Analog
R
Video input (red)
G/G sync Video input (green/sync on green)
B
Video input (blue)
H/C sync Horizontal sync signal, Mac C-sync signal
V
Vertical sync signal
Mouse Input Terminal (for IBM/Mac) : 9-pin D-sub female connector
Pin No.
1
2
3
4
5
6
7
8
9
1
5
6
9
Signal
CD
RD
SD
ER
SG
DR
RS
CS
CI
Name
Carrier Detect
Receive Data
Send Data
Equipment Ready
Signal Ground
Data Set Ready
Request to Send
Clear to Send
Ring Indicator
I/O
Input
Input
Output
Output
Output
Output
Input
Input
Reference
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Mouse Input Terminal (for NEC PC98 series for Japan) : 9-pin mini DIN connector
8
7
9
3
6
5
4
2
Pin No.
1
2
3
4
5
6
7
8
9
Signal
+5V
XA
XB
YA
YB
LEFT
NC
RIGHT
GND
I/O
Input
Input
Input
Input
Input
Input
Input
Input
Reference
Computer output
Computer output
Computer output
Computer output
Computer output
Computer output
Not connected
Computer output
Computer output
1
RS-232C terminal : 9-pin D-sub male connector
1
6
E-33
5
9
Pin No.
1
2
3
4
5
6
7
8
9
Signal
CD
RD
SD
ER
SG
DR
RS
CS
CI
Name
I/O
Receive Data
Send Data
Input
Output
Signal Ground
Data Set Ready
Request to Send
Output
Output
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Not connected
RS-232C Terminal Specifications
1. PC control
The personal computer can be used to control the projector by connecting the two via an RS-232C cable (cross
type) (not supplied).
2. Communication conditions
Set the serial port settings of the computer to match that of the table below.
Signal format:
Baud rate:
Data length:
Parity bit:
Stop bit:
Flow control:
Conforms to RS-232C standard.
9,600 bps
8 bits
NON
1 bit
None
3. Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the
unit processes the command from the computer, it sends a response code to the computer.
Command format
C1
C2
C3 C4
P1
P2
P3
Command 4-digits
Return code (0DH)
P4
Parameter 4-digits
Response code format
Normal response
O
Return code (0DH)
K
Problem response (communication error or incorrect command)
E
R
Return code (0DH)
R
When more than one code is being sent, send each command only after the OK response code for the previous
command from the unit is verified.
Note:
• Using the computer control function of the unit, the liquid crystal projector conditions cannot be read to the computer.
Therefore, confirm the conditions by transmitting the display commands for each adjustment menu and checking the
conditions with the On-Screen Display. If the unit receives a command other than a menu display command, it will execute
the command without displaying the On-Screen Display.
4. Commands
CONTROL ITEM
POWER SETTING
INPUT SWITCHING
INPUT CHECK
LANGUAGE
SELECTION
VIDEO
SYSTEM
SELECTION
VIDEO 1
IMAGE
ADJUSTMENT
VIDEO 2
IMAGE
ADJUSTMENT
VIDEO
BACKGROUND
LEVEL
COMMAND
PARAMETER
CONTROL CONTENTS
C1
C2
C3
C4
P1
P2
P3
P4
P
O
W
R
_
_
_
0
POWER OFF
P
O
W
R
_
_
_
1
POWER ON
I
V
E
D
_
_
_
1
VIDEO 1
I
V
E
D
_
_
_
2
VIDEO 2
I
R
G
B
_
_
_
1
RGB 1
I
R
G
B
_
_
_
2
RGB 2
I
C
H
K
_
_
_
0
INPUT CHECK
M
E
L
A
_
_
_
1
ENGLISH
M
E
L
A
_
_
_
2
DEUTSCH
M
E
L
A
_
_
_
3
ESPANOL
A
_
_
_
4
NEDERLANDS
_
_
5
FRANCAIS
M
E
L
M
E
L
A
_
M
E
L
A
_
_
_
6
ITALIANO
M
E
L
A
_
_
_
7
SVENSKA
M
E
L
A
_
_
_
8
JAPANESE
M
E
S
Y
_
_
_
1
AUTO
M
E
S
Y
_
_
_
2
PAL
M
E
S
Y
_
_
_
3
SECAM
M
E
S
Y
_
_
_
4
NTSC 4.43
M
E
S
Y
_
_
_
5
NTSC 3.58
V
A
P
I
_
*
*
*
PICTURE (-30 ~ +30)
V
A
B
R
_
*
*
*
BRIGHT (-30 ~ +30)
V
A
C
O
_
*
*
*
COLOR (-30 ~ +30)
V
A
T
I
_
*
*
*
TINT (-30 ~ +30)
V
A
S
H
_
_
_
*
SHARPNESS (-30 ~ +30)
V
A
R
E
_
_
_
0
VIDEO 1 DISPLAY
V
A
R
E
_
_
_
1
RESET
V
B
P
I
_
*
*
*
PICTURE (-30 ~ +30)
V
B
B
R
_
*
*
*
BRIGHT (-30 ~ +30)
V
B
C
O
_
*
*
*
COLOR (-30 ~ +30)
V
B
T
I
_
*
*
*
TINT (-30 ~ +30)
V
B
S
H
_
_
_
*
SHARPNESS (-30 ~ +30)
V
B
R
E
_
_
_
0
VIDEO 2 DISPLAY
V
B
R
E
_
_
_
1
RESET
W
B
R
D
_
*
*
*
RED (-30 ~ +30)
W
B
B
E
_
*
*
*
BLUE (-30 ~ +30)
W
B
R
E
_
_
_
1
RESET
Note:
• If a dash appears in the
parameter column enter a
space. If an asterisk appears
enter a value in the range
indicated in brackets under
CONTROL CONTENTS. See
the examples on the next page.
E-34
COMMAND
CONTROL ITEM
VOLUME
ADJUSTMENT
AUDIO
ADJUSTMENT
C1
C2
PARAMETER
C3
C4
P1
P2
P3
CONTROL CONTENTS
P4
V
O
L
A
_
_
*
*
VOLUME (0 ~ 60)
M
U
T
E
_
_
_
0
MUTE OFF
M
U
T
E
_
_
_
1
MUTE ON
A
A
B
L
_
*
*
*
BALANCE (-30 ~ +30)
A
A
T
E
_
*
*
*
TREBLE (-30 ~ +30)
A
A
B
A
_
*
*
*
BASS (-30 ~ +30)
A
A
R
E
_
_
_
0
AUDIO DISPLAY
A
A
R
E
_
_
_
1
RESET
R
A
P
I
_
*
*
*
PICTURE (-30 ~ +30)
R
A
B
R
*
*
BRIGHT (-30 ~ +30)
A
R
D
_
_
*
R
*
*
*
RED (-30 ~ +30)
R
A
B
E
_
*
*
*
BLUE (-30 ~ +30)
R
A
R
E
_
_
_
0
RGB DISPLAY
R
A
R
E
_
_
_
1
RESET
R
B
P
I
_
*
*
*
PICTURE (-30 ~ +30)
R
B
B
R
*
*
*
BRIGHT (-30 ~ +30)
R
B
R
D
_
_
*
*
*
RED (-30 ~ +30)
R
B
B
E
_
*
*
*
BLUE (-30 ~ +30)
R
B
R
E
_
_
_
0
RGB DISPLAY
R
B
R
E
_
_
_
1
RESET
I
N
C
L
_
*
*
*
CLOCK (-60 ~ +60)
I
N
P
H
_
*
*
*
PHASE (-60 ~ +60)
I
A
H
P
_
*
*
*
H-POS (-60 ~ +60)
I
A
V
P
_
*
*
*
V-POS (-30 ~ +30)
I
A
R
E
_
_
_
0
RGB INPUT DISPLAY
I
L
A
N
R
F
E
O
_
_
_
1
RESET
_
*
*
*
LENS FOCUS (-30 ~ +30)
L
N
Z
O
_
*
*
*
LENS ZOOM (-30 ~ +30)
L
N
S
H
_
*
*
*
LENS SHIFT (-30 ~ +30)
I
M
B
E
_
_
_
0
BLUE SCREEN OFF
I
M
B
E
_
_
_
1
BLUE SCREEN ON
I
M
B
K
_
_
_
0
BLACK SCREEN OFF
I
M
B
K
_
_
_
1
BLACK SCREEN ON
I
M
D
I
_
_
_
0
INPUT DISPLAY OFF
I
M
D
I
_
_
_
1
INPUT DISPLAY ON
I
M
R
E
_
_
_
0
REVERSE OFF
I
M
R
E
_
_
_
1
REVERSE ON
I
M
I
N
_
_
_
0
INVERT OFF
I
M
I
N
_
_
_
1
INVERT ON
S
Y
S
E
_
_
_
0
DISPLAY
ON-SCREEN
DISPLAY SETTING
I
M
B
O
_
_
_
0
BLACK SCREEN DISPLAY OFF
I
M
B
O
_
_
_
1
BLACK SCREEN DISPLAY ON
MOUSE
ADJUSTMENT
R
E
M
O
_
_
_
1
REMOTE MOUSE AT
R
D
E
C
M
5
O
V
_
_
_
2
REMOTE MOUSE 98
_
_
_
0
WHEN LAMP IS ON
D
C
5
V
_
_
_
1
WHEN MAIN POWER IS ON
M
E
M
A
_
_
_
0
MEMORY RELEASE
M
E
M
A
_
_
_
*
MEMORY SELECTION (1 ~ 7)
RGB 1 ADJUSTMENT
RGB 2 ADJUSTMENT
RGB INPUT
ADJUSTMENT
SCREEN SETTING
VIDEO
CONFIRMATION
DC 5V OUTPUT
SCREEN MODE
MEMORY
Notes:
• RGB INPUT ADJUSTMENT can only be set in the displayed computer mode.
• The “ⳮ30 ⬃ Ⳮ30” values for Lens Focus, Lens Zoom and Lens Shift indicate the time required to set these functions to their
minimum and maximum adjustment settings.
Examples:
For the RGB/VIDEO setting, select video and set the PAL mode.
Computer
I
V
E
D
—
Unit
—
—
1
→
←
Switch to video screen
O
M
E
S
Y
—
—
—
2
K
→
←
Set to PAL mode
O
K
When BRIGHT of VIDEO IMAGE ADJUSTMENT is set to ⳮ10.
→
V A B
R — — 1
0
←
O
E-35
K
Wired Remote Control Terminal Specifications
1. Specifications of wired remote control input
• 4.4ø minijack
• External: +5V (1A)
• Internal: GND
2. Function and transmission codes
No.
Control Item
System Code
(Function)
Data Code
C1
C2
C3
C4
C5
C6
C7
C8
External Code
C9 C10 C11 C12 C13 C14 C15
Note:
• To operate the MOUSE, L-CLICK and R-CLICK functions
through the wired remote control input, connect the cable from
the wired remote control (supplied) terminal on the projector to
the remote control. The codes for these functions are complex
and are, therefore, not listed here.
1
VOLUME UP
1
0
1
1
0
0
0
1
0
1
0
0
0
1
0
2
VOLUME DOWN
1
0
1
1
0
1
0
1
0
1
0
0
0
1
0
3
POWER ON
1
0
1
1
0
0
1
1
0
1
0
1
0
1
0
4
POWER OFF
1
0
1
1
0
0
1
1
0
1
0
0
1
1
0
5
CURSOR UP
1
0
1
1
0
0
0
1
1
1
0
0
1
1
0
6
CURSOR DOWN
1
0
1
1
0
1
0
1
1
1
0
0
1
1
0
7
ADJUST UP
1
0
1
1
0
1
1
1
1
0
0
1
0
1
0
8
ADJUST DOWN
1
0
1
1
0
0
0
0
0
1
0
1
0
1
0
9
MUTE
1
0
1
1
0
1
1
1
0
1
0
0
0
1
0
10 MENU
1
0
1
1
0
0
0
1
0
0
0
1
1
1
0
11 VIDEO 1
1
0
1
1
0
0
1
0
0
1
1
0
0
1
0
12 VIDEO 2
1
0
1
1
0
1
1
0
0
1
1
0
0
1
0
13 RGB1
1
0
1
1
0
1
0
1
0
1
1
0
0
1
0
C1
14 RGB 2
1
0
1
1
0
0
1
1
0
1
1
0
0
1
0
1
15 ENTER
1
0
1
1
0
1
1
1
0
1
0
1
0
1
0
16 LENS SELECT
1
0
1
1
0
1
1
0
1
0
0
0
1
1
0
17 CHANNEL CALL
1
0
1
1
0
1
1
0
1
1
0
0
0
1
0
18 BLACK SCREEN
1
0
1
1
0
1
0
0
1
0
1
1
0
1
0
Wired remote control function code
LSB
System Code
C5
C6
1
0
*
0
1
MSB
Data Code
*
*
*
*
*
C13
C14
C15
*
1
0
*
* System codes C1 to C5 are fixed at “10110”.
* Codes C14 and C15 are reverse confirmation bits, with
“10” indicating “Front” and “01” indicating “Rear”.
3. Sharp remote control signal format
1) Transmission format
a) 15-bit format
D
D
D
D
D
D
67.5 ms
D
D
D
D
D
D
D
67.5 ms
2) Wave form of output signal
• Output using Pulse Position Modulation
t
T1
T0
“1”
“0”
“0”
“0”
“0”
“1”
“0”
D
26.4 µs
t
•
•
•
•
•
t = 264 µs
To = 1.05 ms
T1 = 2.10 ms
Pulse carrier frequency = 455/12 kHz
Duty ratio = 1:1
3) Transmission control code
a) 15 bit
C1
C2
C3
C4
System Address
D to D Common Data Bit
C5
C6
C7
C8
b) Example of Reverse D to D
C9
C10
Function Key Data Bit
C11
C12
C13
Data
Expansion
C14
Mask
C15
Data
Determination
D
D
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
1
0
1
1
0
1
0
0
0
0
0
0
0
1
0
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
1
0
1
1
0
0
1
1
1
1
1
1
1
0
1
Reverse in D
E-36
Specifications
Product Type
Model
Video system
Display method
LCD panel
Lens
Projection lamp
Contrast ratio
Video input signal
S-video input signal
Video (monitor) output signal
Horizontal resolution
Audio output
Computer RGB input signal
RS-232C input terminal
Mouse input terminal (for IBM/Mac)
Mouse input terminal (for PC98)
Speaker system
Rated voltage
Rated frequency
Power consumption
Operating temperature
Storage temperature
Cabinet
I/R Carrier frequency
Laser Pointer of Remote Control
Dimensions (W × D × H)
Weight
Supplied accessories
Replacement parts
LCD Projector
XG-E3500U
PAL/SECAM/NTSC 3.58/NTSC 4.43
LCD panel × 3, RGB optical shutter method
Panel size:
1.8 ⬙ (27.6 [H] × 36.9 [W] mm)
Display method: Translucent TN liquid crystal panel
Drive method:
TFT (Thin Film Transistor) Active Matrix panel
No. of dots:
786,432 dots (1,024 [H] × 768 [V])
1–1.6 zoom lens, F2.5 to 3.5, f = 66 to 106 mm
370 W Metal halide
100:1
BNC Connector: VIDEO, composite video, 1 Vp-p, sync negative, 75 Ω
terminated
RCA Connector: AUDIO, 0.5 Vrms more than 22 kΩ (stereo)
4-pin mini DIN connector
Y (luminance signal):
1 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
BNC Connector:
VIDEO, composite video, 1Vp-p, sync negative, 75 Ω
terminated
RCA Connector:
AUDIO, 0.5 Vrms less than 2.2 kΩ (stereo)
520 TV lines (video input), 700 TV lines (S-video input)
3 W Ⳮ 3 W (stereo)
Video Signal:
15-pin mini D-sub connector (RGB 1),
BNC connector (RGB 2):
RGB separate/composite sync/sync on
green type analog input: 0-0.7 Vp-p, positive,
75 Ω terminated
Stereo Minijack:
AUDIO, 0.5 Vrms, more than 22 kΩ (stereo)
Horizontal sync. signal: TTL level (positive/negative) or composite sync
(Apple only)
Vertical sync. signal:
Same as above
9-pin D-sub male connector for controlling personal computer
9-pin D-sub female connector for wireless mouse
9-pin mini DIN connector for wireless mouse
3 ⬙ (8 cm) round × 2
AC 120 V
50/60 Hz
535 W
41°F to 104°F (Ⳮ5°C to Ⳮ40°C)
ⳮ4°F to 140°F (ⳮ20°C to Ⳮ60°C)
Plastic
40 kHz
Wave length : 670 nm
Max. output : 1 mW
Class II Laser Product
14.1⬙ × 23.0 ⬙ × 8.2 ⬙ (359 × 585 × 208 mm) projector only
17.5 ⬙ × 23.0 ⬙ × 8.2⬙ (444 × 585 × 208 mm) incl. terminal cover
36.3 lbs. (16.5 kg)
Remote control unit, Four AA batteries, Extra air filter, RGB signal cable
(9.8⬘, 3 m), Macintosh adaptor, Two BNC/RCA adaptors, Mouse control cable for
IBM PS/2 (5.9 ⬙, 15 cm), Mouse control cable for Mac (5.9 ⬙, 15 cm), Mouse control
cable (9.8⬘, 3 m), AC cord, Terminal cover, Inverting labels, Lens cap (installed)
Lamp unit (Lamp/cage module) (BQC-XGE3500U1), Remote control (RRMCG
1392CESA), Air filter (PFILD0082CEZZ), RGB signal cable (QCNW-4910CEZZ),
Macintosh adaptor (QPLGJ1512CEZZ), Mouse control cable for IBM PS/2 (QCNW4754CEZZ), Mouse control cable for Mac (QCNW-4755CEZZ), Mouse control
cable (QCNW-4620CEZZ), AC cord (QACCU5013CEZZ)
Our projector uses LCD (Liquid Crystal Display) panels. These very
sophisticated panels contain 786,432 pixels ( × RGB) TFTs (Thin Film
Transistors).
As with any high technology electronic equipment such as large screen TVs,
video systems and/or video cameras, there are certain acceptable tolerances
that the equipment must conform to. This unit has some inactive TFTs within
acceptable tolerances, which may result in illuminated or inactive dots on the
picture screen.
This will not affect the picture quality or the life expectancy of the unit.
If you have any questions about this matter, please call toll free 1-800BE-SHARP (1-800-237-4277).
U.S.A. ONLY
Specifications are subject to change without notice.
E-37
Dimensions
Rear View
14.8⬙(377)
23.0⬙(585)
13.2⬙(335)
Top View
6.5⬙(165.5)
(Lens housed)
0.2⬙(4)
7.0⬙(176.8)
(Lens extended)
Side View
14.0⬙(355)
4.8⬙(121.1)
(Lens at upper shift)
8.2⬙(208)
1.8⬙(46) 3.7⬙(95)
0.2⬙(6) ø4.7⬙(ø120)
Front View
3.8⬙(96.9)
(Lens at lower shift)
3.5⬙(89)
ø1.8⬙(ø45)
11.7⬙(296)
Bottom View
[Units: inches (mm)]
E-38