Dell 1609WX - WXGA DLP Projector User`s guide

Dell™ 1609WX Projector
User’s Guide
Downloaded From projector-manual.com DELL Manuals
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you
make better use of your projector.
NOTICE: A NOTICE indicates either potential damage to
hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property
damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2008 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell
Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell
Inc.; DLP, DLP® logo and DarkChip™2 are either trademarks for Texas
Instruments; Microsoft and Windows are registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either
the entities claiming the marks and names or their products. Dell Inc. disclaims
any proprietary interest in trademarks and trade names other than its own.
Model 1609WX
February 2008 Rev. A00
Downloaded From projector-manual.com DELL Manuals
Contents
1
About Your Projector
About Your Projector
2
. . . . . . . . . . . . . . . . .
Connecting Your Projector .
Connecting a Computer
5
. . . . . . . . . . . . . . . .
7
. . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
Connecting a Computer Using a VGA Cable
. . . . .
Connecting a Computer Using a DVI-D Cable
. . . .
Connecting a Computer Using an RS232 Cable .
. .
6
8
8
9
10
Monitor Loop-Through Connection Using VGA Cables 11
Connecting a DVD Player
. . . . . . . . . . . . . . . .
Connecting a DVD Player Using an S-video Cable
.
12
12
Connecting a DVD Player Using a Composite Cable 13
Connecting a DVD Player Using a Component Cable 14
Connecting a DVD Player Using a Component Cable 15
Connecting a DVD Player Using a HDMI Cable
3
. .
16
Using Your Projector
. . . . . . . . . . . . . . . .
17
Turning Your Projector On
. . . . . . . . . . . . . . . .
17
Turning Your Projector Off
. . . . . . . . . . . . . . . .
17
Adjusting the Projected Image
. . . . . . . . . . . . .
Raising the Projector Height
. . . . . . . . . . . .
Lowering the Projector Height
. . . . . . . . . . .
Contents
Downloaded From projector-manual.com DELL Manuals
18
18
18
3
Adjusting the Projector Zoom and Focus
. . . . . . . .
19
. . . . . . . . . . . .
20
. . . . . . . . . . . . . . . . .
21
Adjusting Projection Image Size
Using the Control Panel
Using the Remote Control
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . .
25
. . . . . . . . . . . . . . . . . . . . .
26
Using the On-Screen Display
Main Menu
INPUT SELECT
. . . . . . . . . . . . . . . . . . .
26
AUTO-ADJUST
. . . . . . . . . . . . . . . . . . .
27
. . . . . . . . . . . . . . . . . . . . . . .
27
SET UP
PICTURE (in PC Mode)
. . . . . . . . . . . . . . .
PICTURE (in Video Mode)
DISPLAY (in PC Mode)
LAMP
28
. . . . . . . . . . . . .
29
. . . . . . . . . . . . . . .
30
DISPLAY (in Video Mode)
. . . . . . . . . . . . .
31
. . . . . . . . . . . . . . . . . . . . . . . .
32
LANGUAGE
OTHERS .
4
24
. . . . . . . . . . . . . . . . . . . . .
33
. . . . . . . . . . . . . . . . . . . . . .
34
Troubleshooting Your Projector
. . . . . . .
37
. . . . . . . . . . . . . . . . . . .
41
. . . . . . . . . . . . . . . . . . . . .
43
Changing the Lamp
5
Specifications
6
Contacting Dell
7
Appendix: Glossary
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
4
Contents
Downloaded From projector-manual.com DELL Manuals
47
48
1
About Your Projector
Before connecting your projector ensure that all the necessary components are
available. Your projector ships with the components shown below. Contact Dell
(see Contacting Dell on page 47) if any of the components are missing.
Your Dell™ 1609WX projector ships with the following components:
Package Contents
Power cable
1.8m VGA cable (VGA to VGA)
CR2032 Battery
Remote control
CR2032
3V
CD Owner’s manual &
Documentation
Carrying case
DELL
About Your Projector
Downloaded From projector-manual.com DELL Manuals
5
About Your Projector
1
6
2
3
5
4
1
Control panel
2
Zoom tab
3
Focus ring
4
Lens
5
Elevator button
6
IR receivers
CAUTION: Safety Instructions
1 Do not use the projector near appliances that generate a lot of heat.
2 Do not use the projector in areas where there is an excessive amount of dust. The
dust may cause the system to fail and projector will automatically shutdown.
3 Ensure that the projector is mounted in a well-ventilated area.
4 Do not block the ventilation slots and openings on the projector.
5 Ensure the projector operates between ambient temperatures (5ºC to 35ºC).
NOTE: For more information, see the safety information that shipped with your
projector.
6
About Your Projector
Downloaded From projector-manual.com DELL Manuals
2
Connecting Your Projector
1
2
DVI-D In
VGA - A
Out
3
4
5
6
7
8
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
9
USB
Remote
10
RS-232
Dell 1609WX
11
12
1
DVI-D input connector
2
VGA-A output (monitor loop-through)
3
VGA-A input (D-sub) connector
4
VGA-B input (D-sub) connector
5
S-video connector
6
Composite video connector
7
Audio input connector
8
Audio output connector
9
USB remote connector
10
RS232 connector
11
Security cable slot
12
Power cable connector
CAUTION: Before you begin any of the procedures in this section, follow the
Safety Instructions as described on page 6.
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
7
Connecting a Computer
Connecting a Computer Using a VGA Cable
1
DVI-D In
VGA - A
Out
VGA - A
In
VGA - B
In
2
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
XELOM
3
1
Power cable
2
VGA to VGA cable
3
USB to USB cable
NOTE: The USB cable is not provided by Dell.
NOTE: The USB cable must be connected if you want to use the Next Page and
Previous Page features on the remote control.
8
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
Connecting a Computer Using a DVI-D Cable
1
DVI-D In
VGA - A
Out
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
TV OUT
SDIF-OUT
PDIF-OUT
XELOM
2
1
Power cable
2
DVI-D cable
3
USB to USB cable
3
NOTE: The USB cable and DVI-D cable are not provided by Dell.
NOTE: The USB cable must be connected if you want to use the Next Page and
Previous Page features on the remote control.
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
9
Connecting a Computer Using an RS232 Cable
1
DVI-D In
VGA - A
Out
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
2
1
Power cable
2
RS232 cable
NOTE: The RS232 cable is not provided by Dell. You can buy the RS232 cable
(6ft) from the Dell website.
10
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
Monitor Loop-Through Connection Using VGA Cables
1
DVI-D In
VGA - A
Out
2
1
Power cable
2
VGA to VGA cable
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
2
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
11
Connecting a DVD Player
Connecting a DVD Player Using an S-video Cable
1
DVI-D In
VGA - A
Out
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
2
1
Power cable
2
S-video cable
NOTE: The S-video cable is not provided by Dell. You can buy the S-Video
Extension (50ft/100ft) cable from the Dell website.
12
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
Connecting a DVD Player Using a Composite Cable
1
DVI-D In
VGA - A
Out
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
2
1
Power cable
2
Composite video cable
NOTE: The Composite cable is not provided by Dell. You can buy the Composite
Video Extension (50ft/100ft) cable from the Dell website.
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
13
Connecting a DVD Player Using a Component Cable
Using a YPbPr to VGA Cable
1
DVI-D In
VGA - A
Out
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
2
1
Power cable
2
VGA to YPbPr cable
NOTE: The VGA to YPbPr cable is not provided by Dell. You can buy the VGA to
YPbPr Extension (50ft/100ft) cable from the Dell website.
Input.
NOTE: You can connect the component cable to either VGA-A Input or VGA-B
14
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
Connecting a DVD Player Using a Component Cable
Using a YPbPr to YPbPr Cable and a YPbPr to VGA Adapter
1
DVI-D In
VGA - A
Out
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
3
2
1
Power cable
2
YPbPr to YPbPr cable
3
YPbPr to VGA adapter
NOTE: The YPbPr to YPbPr cable and the VGA to YPbPr adapter are not
provided by Dell.
Input
NOTE: You can connect the component cable to either VGA-A Input or VGA-B
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
15
Connecting a DVD Player Using a HDMI Cable
1
DVI-D In
VGA - A
Out
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
3
2
1
Power cable
2
HDMI cable
3
DVI-D adapter
NOTE: The HDMI cable and DVI-D adapter are not provided by Dell.
16
Connecting Your Projector
Downloaded From projector-manual.com DELL Manuals
3
Using Your Projector
Turning Your Projector On
NOTE: Turn on the projector before you turn on the source. The Power light
blinks blue until the Power button is pressed.
1 Remove the lens cap.
2 Connect the Power cable and appropriate signal cables. For information about
connecting the projector, see Connecting Your Projector on page 7.
3 Press the projector Power button (see Using the Control Panel on page 21 to
locate the Power button).
4 Turn on your source (computer, DVD player, etc.). The projector automatically
detects your source.
If you have multiple sources connected to the projector, press the Source
button on the remote control or control panel to select the desired source.
5 The Dell Logo will continue for 30 seconds while power on.
If the "Searching for signal..." message appears on the screen, ensure that the
appropriate cables are securely connected.
Turning Your Projector Off
NOTICE: You must turn off the projector before you disconnect the power
cable from the projector.
1 Press the Power button.
2 Press the Power button again. The cooling fans continue to operate for 90 seconds.
3 Disconnect the Power cable from the electrical outlet and the projector.
NOTE: Wait for 60 seconds before you turn the projector on again.
NOTE: If you press the Power button while the projector is running, the "Press
Power Button to Turn off Projector" message appears on the screen. To clear the
message, press the Menu button on the control panel or ignore the message; the
message disappears after 5 seconds.
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
17
Adjusting the Projected Image
Raising the Projector Height
1 Press the Elevator button.
2 Raise the projector to the desired display angle, and then release the button to
lock the elevator foot into position.
3 Use the tilt adjustment wheel to fine-tune the display angle.
Lowering the Projector Height
1 Press the Elevator button.
2 Lower the projector, and then release the button to lock the elevator foot into
position.
1
2
3
1
Elevator button
2
Elevator foot
3
Tilt adjustment wheel
3
18
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
Adjusting the Projector Zoom and Focus
CAUTION: To avoid damaging the projector, ensure that the zoom lens and
elevator foot are fully retracted before moving the projector or placing the
projector in its carrying case.
1 Rotate the zoom tab to zoom in and out.
2 Rotate the focus ring until the image is clear. The projector focuses at distances
ranging between 3.3 ft to 39.4 ft(1.0 m to 12 m).
1
2
1
Zoom tab
2
Focus ring
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
19
Adjusting Projection Image Size
359.4"(913.0cm)
"
7.7 m)
32 .4c
32
8
(
269.6"(684.7cm)
209.7"(532.6cm)
"
1.2 m)
19 .6c
5
8
(4
149.8"(380.4cm)
"
6.6 m)
13 .8c
46
3
(
89.9"(228.2cm)
3.3'(1.0m)
DVI-D In
VGA - A
Out
Dell 1609WX
20
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
30.0 "(76.1cm)
27.3"
(69.4cm)
9.8'(3.0m)
16.4'(5.0m)
23.0'(7.0m)
.9" )
81 .1cm
8
0
(2
29.5'(9.0m)
39.4'(12.0m)
Projector to screen distance
"
5.8 m)
24 .3c
24
6
(
VGA - A
In
VGA - B
In
S-Video In
Video In
Audio In
Audio Out
USB
Remote
RS-232
Screen
(Diagonal)
Max.
30.0"
(76.1cm)
89.9"
(228.2cm)
149.8"
(380.4cm)
209.7"
(532.6cm)
269.6"
(684.7cm)
359.4"
(913.0cm)
Min.
27.3"
(69.4cm)
81.9"
(208.1cm)
136.6"
(346.8cm)
191.2"
(485.6cm)
245.8"
(624.3cm)
327.7"
(832.4cm)
25.4" X 15.9"
76.2" X 47.6"
127" X 79.4"
(64.5cm X
40.3cm)
(193.5cm X
121.0cm)
(322.6cm X
201.6cm)
23.2" X 14.5"
69.5" X 43.4"
115.8" X 72.4"
(58.8cm X
36.8cm)
(176.5cm X
110.3cm)
(294.1cm X
183.8cm)
(411.8cm X
257.4cm)
(529.4cm X
330.9cm)
(705.9cm X
441.2cm)
Max.
1.97"
(5.0cm)
5.91"
(15.0cm)
9.84"
(25.0cm)
13.78"
(35.0cm)
17.72"
(45.0cm)
23.62"
(60.0cm)
Min.
1.79"
(4.56cm)
5.38"
(13.68cm)
8.97"
(22.79cm)
12.56"
(31.91cm)
16.15"
(41.03cm)
21.54"
(54.71cm)
3.3' (1.0m)
9.8' (3.0m)
16.4' (5.0m)
23.0' (7.0m)
29.5' (9.0m)
39.4' (12.0m)
Max.
(WxH)
Screen
Size
Min.
(WxH)
Hd
Distance
177.8" X 111.1" 228.8" X 142.9" 304.8" X 190.5"
(451.6cm X
282.3cm)
(580.6cm X
362.9cm)
(774.2cm X
483.9cm)
162.1" X 101.3" 208.4" X 130.3" 277.9" X 173.7"
* This graph is for user reference only.
Using the Control Panel
1
2
3
4
10
5
9
6
8
7
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
21
1
LAMP warning light
• If the LAMP light is solid amber, replace the
lamp (see Changing the Lamp on page 41). If
this problem persists, contact Dell (see
Contacting Dell on page 47).
• If the LAMP light is blinking amber, the
projector automatically shuts down indicating a
system failure. If this problem persists, contact
Dell (see Contacting Dell on page 47).
2
TEMP warning light
• A solid amber TEMP light indicates that the
projector, lamp, or lamp driver are overheated.
The display automatically shuts down. Turn the
display on again after the projector cools down.
If the problem persists, contact Dell (see
Contacting Dell on page 47).
• A blinking amber TEMP light indicates that a
projector fan or color wheel have failed and the
projector automatically shuts down. If the
problem persists, contact Dell (see Contacting
Dell on page 47).
3
Power
Allows you to turn the projector on and off. For
more information, see Turning Your Projector On
on page 17 and Turning Your Projector Off on
page 17.
4
Up
/ Keystone
adjustment
Allows you to select options from the On Screen
Display (OSD) menu. You can also use the Up
button to adjust he image distortion caused
by tilting the projector.
5
Right
Allows you to adjust the OSD setting.
/ Auto Adjust
You can also use the Right
button to
synchronize the projector to the input source.
Auto adjust does not operate if the OSD is
displayed.
6
IR Receiver
Point the remote control towards the IR receiver
and press a button.
22
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
7
Down
/ Keystone
adjustment
Allows you to select options from the On Screen
Display (OSD) menu.
You can also use the Down
button to adjust
the image distortion caused by tilting the
projector.
8
Menu
9
Left
Allows you to activate the OSD. Use
and the Menu button to navigate through the
OSD.
/ Source
Allows you to adjust the OSD setting.
You can also use the
button to toggle through
Digital RGB, Analog RGB, Composite,
Component (YPbPr via VGA), and S-video
sources when multiple sources are connected to
the projector.
10
Enter
Allows you to confirm a selected OSD option.
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
23
Using the Remote Control
1
11
2
12
3
13
4
5
14
15
6
7
16
17
8
18
9
19
10
20
1
LED light
LED indicator.
2
Source
Press to switch between Digital RGB, Analog
RGB, Composite, S-video, Component (YPbPr
via VGA).
3
Auto adjust
Press to synchronize the projector to the input
source. Auto adjust does not operate if the OSD
(On-Screen Display) is displayed.
4
Up button
Press to select an item on the OSD.
5
Left button
Press to adjust the OSD setting.
6
Enter
Press to confirm the selection.
7
Menu
Press to activate the OSD.
8
Down button
Press to select an item on the OSD.
9
Mute
Press to mute or un-mute the projector speaker.
24
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
10 Aspect ratio
Press to change the aspect ratio of a displayed
image.
11 Power
Turns the projector on and off. For more
information, see Turning Your Projector On on
page 17 and Turning Your Projector Off on
page 17.
12 Video mode
The Dell 1609WX Micro-projector has preset
configurations that are optimized for displaying
data (PC Graphics) or video (movies, games,
etc.). Press the Video Mode button to toggle
between PC mode, Movie mode, Game Mode,
sRGB, or CUSTOM mode (for user to setup and
save preferred settings). Pressing the Video Mode
button once will show the current display mode.
Pressing the Video Mode button again will switch
between display modes.
13 Page up
Press to move to the previous page.
14 Blank screen
Press to hide/un-hide the image.
15 Page down
Press to move to the next page.
16 Right button
Press to adjust the OSD setting.
17 Volume up
Press to increase the volume.
18 Keystone adjustment Press to adjust image distortion caused by tilting
the projector. (+40/-35 degrees)
19 Volume down
Press to decrease the volume.
20 Keystone adjustment Press to adjust image distortion caused by tilting
the projector. (+40/-35 degrees)
Using the On-Screen Display
The projector has a multi-language On-Screen Display (OSD) that can be
displayed with or without an input source present.
To navigate through the tabs in the Main menu, press the
or
buttons on
your projectors control panel or remote control. To select a submenu, press the
Enter button on your projectors control panel or remote control.
To select an option, press the
or
on your projectors control panel or remote
control. The color changes to dark blue. When an item is selected, the color
changes to dark blue. Use
or
on the control panel or remote control to
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
25
adjust the settings.
To go back to Main menu, go to Back tab and press the Enter button on the
control panel or the remote control.
To exit the OSD, go to EXIT tab and press the Enter button or press the Menu
button directly on the control panel or the remote control.
Main Menu
INPUT SELECT
The Input Select menu allows you to select your projectors input source.
manually select the input signal.
AUTO SOURCE—Select On (the
default) to autodetect the
available input signals. If you
press the Source button when
the projector is on, it
automatically finds the next
available input signal. Select
Off to lock the current input
signal. If you press the Source
button when the Auto Source
mode is set to Off, you can
VGA-A—Press Enter to detect VGA-A signal.
VGA-B—Press Enter to detect VGA-B signal.
DVI-D—Press Enter to detect DVI-D signal.
S-VIDEO—Press Enter to detect S-Video signal.
COMPOSITE VIDEO—Press Enter to detect Composite Video signal.
26
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
AUTO-ADJUST
Auto Adjust automatically adjusts the
projector's FREQUENCY and
TRACKING in PC mode. While
Auto Adjustment is in progress, the following message appears on the screen,
"Auto Adjustment in Progress...".
SET UP
It includes V. Keystone, Auto Keystone, Projector Mode, Aspect Ratio and
Projector Info settings.
V. KEYSTONE—Adjusts the image distortion caused by tilting the projector.
AUTO KEYSTONE—Auto adjusts the image distortion by tilting the projector.
PROJECTOR MODE—Allows you to select the projector mode, depending upon how
the projector is mounted.
•
Front Projection-Desktop — This is the default option.
•
Front Projection-Ceiling Mount — The projector turns the image upside
down for ceiling-mounted projection.
•
Rear Projection-Desktop — The projector reverses the image so that you can
project from behind a translucent screen.
•
Rear Projection-Ceiling Mount — The projector reverses and turns the
image upside down. You can project from behind a translucent screen with a
ceiling-mounted projection.
ASPECT RATIO—Allows you to set the aspect ratio.
•
Original — The input source scales to fit the screen while keeping the aspect
ratio of the input source.
•
4:3 — The input source scales to fit the height of the screen.
•
Wide — The input source scales to fit the screen.
Use Wide or 4:3 if you are using one of the following:
– Computer resolution greater than WXGA
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
27
– Component cable (720p/1080i/1080p)
PROJECTOR INFO—Displays the projector model name, the present input source and
projector series number (PPID#).
PICTURE (in PC Mode)
Using the Picture menu, you can adjust the display settings of your projectors. The
Picture menu, provides the following options:
BRIGHTNESS—Use
CONTRAST—Use
and
and
to adjust the brightness of the image.
to adjust the display contrast.
COLOR TEMP—Allows you to adjust the color temperature. The screen appears
cooler at higher color temperatures and warmer at lower color temperatures.
COLOR ADJUST—Allows you to manually adjust the colours red, green, and blue.
When you adjust the values in the Color Adjust menu, the Custom mode is
activated. The values are saved in the Custom mode.
28
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
PICTURE (in Video Mode)
Using the Picture menu, you can adjust the display settings of your projectors. The
Picture menu, provides the following options:
BRIGHTNESS—Use
CONTRAST—Use
and
and
to adjust the brightness of the image.
to adjust the display contrast.
COLOR TEMP—Allows you to adjust the color temperature. The screen appears
cooler at higher color temperatures and warmer at lower color temperatures.
COLOR ADJUST—Allows you to manually adjust the colours red, green, and blue.
When you adjust the values in the Color Adjust menu, the Custom mode is
activated. The values are saved in the Custom mode.
SATURATION—Allows you to adjust the video source from black and white to fully
saturated color. Press
to decrease the amount of color in the image and
to
increase the amount of color in the image.
SHARPNESS—Allows you to adjust the image sharpness. Press
sharpness and
to increase the sharpness.
to decrease the
to increase the amount of green in the image and
to
increase the amount of red in the image (Selectable for NTSC only).
TINT—Press
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
29
DISPLAY (in PC Mode)
Using the Display menu, you can adjust the display settings of your projectors.
The Picture menu, provides the following options:
VIDEO MODE—Allows you to optimize the projectors display mode:
PC, Movie, sRGB (provides more accurate color representation), Game, and
Custom (set your preferred settings). If you adjust the settings for White Intensity
or Degamma, the projector automatically switches to Custom.
NOTE: If you adjust the settings for White Intensity or Degamma, the projector
automatically switches to Custom.
SIGNAL TYPE—Allows you to manually select signal type RGB, YCbCr, or YPbPr.
to digitally magnify an image up to 4 times on the projection
ZOOM—Press
screen and press
to reduce the zoomed image.
ZOOM NAVIGATION—Press
to navigate projection screen.
WHITE INTENSITY—Set 0 to maximize the color reproduction and 10 to maximize
the brightness.
DEGAMMA—Allows you to adjust among the 4 preset values (1, 2, 3, 4) to change
the color performance of the display.
HORIZONTAL POSITION—Press
image to the right.
VERTICAL POSITION—Press
to move the image to the left and
to move the image down and
30
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
to move the
to move the image up.
FREQUENCY—Allows you to change the display data clock frequency to match the
frequency of your computer graphics card. If you see a vertical flickering wave, use
Frequency control to minimize the bars. This is a coarse adjustment.
TRACKING—Allows you to sybchronize the phase of the display signal with the
graphic card. If you experience an unstable or flickering image, use Tracking to
correct it. This is a fine adjustment.
DISPLAY (in Video Mode)
Using the Display menu, you can adjust the display settings of your projectors.
The Picture menu, provides the following options:
VIDEO MODE—Allows you to optimize the projectors display mode:
PC, Movie, sRGB (provides more accurate color representation), Game, and
Custom (set your preferred settings). If you adjust the settings for White Intensity
or Degamma, the projector automatically switches to Custom.
NOTE: If you adjust the settings for White Intensity or Degamma, the projector
automatically switches to Custom.
SIGNAL TYPE—Manually select signal type RGB, YCbCr, or YPbPr.
to digitally magnify an image up to 4 times on the projection
ZOOM—Press
screen and press
to reduce the zoomed image.
ZOOM NAVIGATION—Press
to navigate projection screen.
WHITE INTENSITY—Set 0 to maximize the color reproduction and 10 to maximize
the brightness.
DEGAMMA—Adjust among the 4 preset values (1, 2, 3, 4) to change the color
performance of the display.
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
31
LAMP
Using the Lamp menu, you can adjust the display settings of your projectors. The
Picture menu, provides the following options:
LAMP HOUR—Displays the operating hours since the last lamp timer reset.
POWER SAVING—Select Yes to set the Power Saving delay period. The delay period is
the time you want the projector to wait without an input signal. By default, the
delay period is set to 120 minutes. However, you can set this to 5, 15, 30, 45, 60, or
120 minutes.
If an input signal is not detected during the delay period, the projector turns off
the lamp and goes into power saving mode. If an input signal is detected when
projector is in power saving mode, the projector automatically turns on. If an input
signal is not detected within two hours, the projector switches from Power Saving
mode to Power Off mode. To turn on the projector press the Power button.
ECO MODE—Select On to use the projector at a lower power level (216 Watts),
which may provide longer lamp life, quieter operation, and dimmer luminance
output on the screen. Select Off to operate at normal power level (256 Watts).
LAMP RESET—After you install a new lamp, select Yes to reset the lamp timer.
QUICK SHUTDOWN—Select Yes to turn off the projector with a single press of the
Power button. This function allows the projector to quick power off with an
accelerated fan speed.
NOTE: If Quick Shutdown is enabled, expect a slightly higher acoustic noise
during power off.
32
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
LANGUAGE
The Language menu allows you to set the language for the OSD.
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
33
OTHERS
VOLUME—Press
and
to decrease/increase the volume.
MUTE—Allows you to enable/disable sound.
CUSTOMIZED SCREEN—Press Enter the Customized Screen menu appears.
Select YES to capture the screen image as a My Customized logo. This
screen replaces all the original screens with the Dell logo. You can recover the
default screen by selecting Dell Logo on the pop-up screen.
NOTE: To capture a full image, ensure the input signal that is connected to
projector is 1280x800 resolution.
MENU LOCK—Select On to enable Menu Lock and hide the OSD menu.
Select OFF to disable the Menu Lock and display the OSD menu.
NOTE: If the OSD disappears while you disable Menu Lock, press the Menu
button on the projectors control panel for 15 seconds, then disable the function.
MENU TIMEOUT—Allows you to adjust the time for an OSD Timeout. By
default, the OSD disappears after 30 seconds of non-activity.
MENU POSITION—Allows you to select the position of the OSD menu on the
screen.
MENU TRANSPARENCY—Select to change the transparency level of the OSD
background.
34
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
PASSWORD—Allows you to password protect the projector. This security
utility enables you to impose a variety of access restrictions to protect your
privacy and stop others from tampering with your projector. This means that
the projector cannot be used if it is taken without authorization, and thus
serves as a theftprevention feature. Select On to enable password protection.
A Please Key In the Password screen appears requesting you to enter a
password when the projector is powered on the next time. Select Off to
disable password protection.
NOTE: Password protection is disabled by default. If you enable this feature,
you will be asked to enter the projector's password after you turn on the
projector.
First time password input request:
a
Go to Others menu, press Enter and then select Password to
Enable the password setting.
b
Enable the Password function will pop up a character screen, key in
a 4-digit number from the screen and press the Enter button.
c
To confirm, enter the password again.
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
35
d
If the password verification is successful, you may resume with
accessing the projector's functions and its utilities.
If you have entered incorrect password, you will be given another two
chances. After the three invalid attempts, the projector will
automatically turn off.
NOTE: If you forget your password, contact DELL™ or qualified service
personnel.
To cancel the password function, select Off and enter the password to
disable the function.
CHANGE PASSWORD—Key in the original password, then enter the new password
and confirm the new password again.
TEST PATTERN—Select On to activate the built-in Test Pattern for self-testing
on focus and resolution. Select Off to disable the function.
FACTORY RESET —Select On to reset the projector to its factory default settings.
Reset items include both computer sources and video source settings.
36
Using Your Projector
Downloaded From projector-manual.com DELL Manuals
Troubleshooting Your Projector
4
If you experience problems with your projector, see the following troubleshooting
tips. If the problem persists, contact Dell. See Contacting Dell on page 47.
Problem
Possible Solution
No image appears on the
screen
• Ensure that the lens cap is removed and the
projector is turned on.
• Ensure the external graphics port is enabled. If
you are using a Dell™ portable computer, press
(Fn+F8). For other computers, see
your respective documentation.
• Ensure that all the cables are securely
connected. See Connecting Your Projector on
page 7.
• Ensure that the pins of the connectors are not
bent or broken.
• Ensure that the lamp is securely installed (see
Changing the Lamp on page 41).
• Use Test Pattern in the Others menu (see
Others on page 47). Ensure that the colors of
the test pattern are correct.
Troubleshooting Your Projector
Downloaded From projector-manual.com DELL Manuals
37
Problem (continued)
Partial, scrolling, or
incorrectly displayed image
Possible Solution (continued)
1 Press the Auto Adjust button on the remote
control or the control panel.
2 If you are using a Dell™ portable computer, set
the resolution of the computer to WXGA
(1280x800) or XGA (1024 x 768):
a Right-click the unused portion of your
Windows desktop, click Properties and then
select Settings tab.
b Verify the setting is 1280x800 or 1024 x 768
pixels for the external monitor port.
c Press
(Fn+F8).
If you experience difficulty in changing
resolutions or your monitor freezes, restart all the
equipment and the projector.
If you are not using a Dell™ portable computer,
see your documentation.
The screen does not display
your presentation
If you are using a Dell™ portable computer, press
(Fn+F8).
Image is unstable or
flickering
Adjust the tracking in the OSD Display submenu (in PC Mode only, see Tracking on
page 31).
Image has vertical flickering
bar
Adjust the frequency in the OSD Display submenu (in PC Mode only, see Frequency on
page 31).
Image color is incorrect
• If the display receives the wrong signal output
from the graphics card, please set the signal type
to RGB in the OSD Display tab.
• Use Test Pattern in the Others menu. Ensure
that the colors of the test pattern are correct.
Image is out of focus
1 Adjust the focus ring on the projector lens.
2 Ensure that the projection screen is within the
required distance from the projector
(3.3 ft [1.0 m] to 39.4 ft [12 m]).
38
Troubleshooting Your Projector
Downloaded From projector-manual.com DELL Manuals
Problem (continued)
Possible Solution (continued)
The image is stretched
The projector automatically detects the input
when displaying a 16:9 DVD signal format. It will maintain the aspect ratio of
the projected image according to input signal
format with an Original setting.
If the image is still stretched, adjust the aspect
ratio in the Set Up menu in the OSD.
Image is reversed
Select Set Up from the OSD and adjust the
projector mode.
Lamp is burned out or
makes a popping sound
When the lamp reaches its end of life, it may burn
out and may make a loud popping sound. If this
occurs, the projector does not turn back on. To
replace the lamp, see Changing the Lamp on
page 41.
LAMP light is solid amber
If the LAMP light is solid amber, replace the
lamp.
LAMP light is blinking
amber
If the LAMP light and the Power light are
blinking amber, the lamp driver has failed and the
projector will automatically shut down.
If the LAMP light is blinking amber and Power
light is solid blue, the color wheel has failed and
the projector will automatically shut down.
Unplug the Power cable after 3minutes then turn
the display on again. If this problem persists,
contact Dell™ (see Contacting Dell on page 47).
TEMP light is solid amber
The projector has overheated. The display
automatically shuts down. Turn the display on
again after the projector cools down. If the
problem persists, contact Dell™ (see Contacting
Dell on page 47).
TEMP light is blinking
amber
A projector fan has failed and the projector will
automatically shut down. If the problem persists,
contact Dell™ (see Contacting Dell on page 47).
The OSD does not appear
on the screen
Try to press the Menu button on the panel for 15
seconds to unlock the OSD. Check the Menu
Lock on page 34.
Troubleshooting Your Projector
Downloaded From projector-manual.com DELL Manuals
39
Problem (continued)
Possible Solution (continued)
The remote control is not
operating smoothly or works
only within a limited range
The battery may be low. Check if the LED
indicator from the remote is too dim. If so, replace
with a new CR2032 battery.
40
Troubleshooting Your Projector
Downloaded From projector-manual.com DELL Manuals
Changing the Lamp
The following message appears on the screen when your projector lamp is
approaching end of life and requires to be changed:
Lamp is approaching the end of its useful life in full power operation.
Replacement suggested! www.dell.com/lamps
CAUTION: Before you begin any of the procedures in this section, follow the
Safety Instructions as described on page 6.
To replace the lamp:
1 Turn off the projector and disconnect the Power cable.
CAUTION: The lamp becomes very hot when in use. Do not attempt to replace
the lamp until the projector has been allowed to cool down for at least 30
minutes.
2 Let the projector cool for at least 30 minutes.
3 Loosen the two screws that secure the lamp cover, and remove the cover.
CAUTION: Do not touch the projector lamp or the lamp glass at any time.
Projector lamps are very fragile and may shatter if touched.
CAUTION: If the lamp shatters, remove all broken pieces from the projector
and dispose or recycle according to state, local, or federal law. For more
information see - www.dell.com/hg.
4 Loosen the two screws that secure the lamp.
5 Pull the lamp up by its metal handle.
Troubleshooting Your Projector
Downloaded From projector-manual.com DELL Manuals
41
6 Replace with the new lamp.
NOTE: Dell™ may require lamps replaced under warranty to be returned to
Dell™. Otherwise, dispose or recycle the lamp. For more information, see Lamp
Disposal on page 42.
7 Tighten the two screws that secure the lamp.
8 Replace the lamp cover and tighten the two screws.
9 Reset the lamp usage time (See Lamp menu on page 32).
CAUTION: Lamp Disposal (for the US only)
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL
LAWS. FOR MORE INFORMATION, GO TO WWW.DELL.COM/HG OR CONTACT
THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. FOR LAMP
SPECIFIC DISPOSAL INFORMATION CHECK WWW.LAMPRECYCLE.ORG.
42
Troubleshooting Your Projector
Downloaded From projector-manual.com DELL Manuals
5
Specifications
Light Valve
0.65" WXGA DMD Type A,
DarkChip™2
Brightness
2500 ANSI Lumens (Max.)
Contrast Ratio
1900:1 Typical (Full On/Full Off)
Uniformity
85% Typical (Japan Standard - JBMA)
Lamp
200-watt user-replaceable 3000-hour
lamp (up to 4000 hours in eco mode)
Number of Pixels
1280x800 (WXGA)
Displayable Color
16.7M colors
Color Wheel Speed
2X
Projection Lens
F-Stop: F/ 2.44~2.58
Focal length, f=21.8~23.8 mm
1.1X manual Zoom Lens
Projection Screen Size
27.3~359.4 inches (diagonal)
Projection Distance
3.3~39.4 ft (1.0 m~12 m)
Video Compatibility
Composite Video / S-Video: NTSC (M,
J, N, 4.43MHz, 3.58MHz), PAL (B, G,
D, K, I, M, N, Nc, 60), SECAM (B, G,
D, K, K1, L)
Component Video (via VGA) / DVI:
1080i/p, 720p, 576i/p, 480i/p
Power Supply
Universal AC90-264 50/60 Hz with
PFC input
Power Consumption
256 watts in full mode, 216 watts in eco
mode
Audio
1 speaker, 8 watt RMS
Noise Level
34 dB(A) Full-on mode, 31 dB(A) Eco
mode
Specifications
Downloaded From projector-manual.com DELL Manuals
43
Weight
4.95 lbs (2.25 kg)
Dimensions (W x H x D)
External 11.68 x 7.96 x 3.17 ± 0.04
inches (296.5 x 202 x 80.5 ± 1 mm)
Environmental
Operating temperature: 5oC - 35oC
(41oF- 95oF)
Humidity: 80% maximum
Storage temperature: 0oC to 60oC
(32oF to 140oF)
Humidity: 90% maximum
Regulatory
FCC, CE, VCCI, UL, cUL, NemkoGS, ICES-003, MIC, C-Tick, GOST,
CCC, PSB, NOM, IRAM, SABS,
CECP, SASO, PSE, eK
I/O Connectors
Power: AC power input socket
Computer input: two D-sub for
analog/component, HDTV input
signals
Computer output: one 15-pin D-sub
Video input: one composite video RCA
and one S-video
Audio input: one phone jack (diameter
3.5 mm)
Audio output: one phone jack
(diameter 3.5 mm)
USB port: one USB slave for remote
mouse support
One mini-DIN RS232 for wired remote
control from PC
DVI-D input: one DVI-D connector for
DVI-D signal (HDCP compliant).
44
Specifications
Downloaded From projector-manual.com DELL Manuals
RS232 Pin Assignment
RS232 Protocol
•
Communication Settings
Connection settings
•
Value
Baud Rate:
19200
Data Bits:
8
Parity
None
Stop Bits
1
Command types
To pop up the OSD menu and adjust the settings.
•
Control command Syntax (From PC to Projector)
[H][AC][SoP][CRC][ID][SoM][COMMAND]
[H][AC][SoP][CRC][ID][SoM][COMMAND] [Value]
•
Example: Power ON Command (Send low byte firstly)
Enter the following code:
0xbe, 0xef, 0x10, 0x05, 0x00, 0xc6, 0xff, 0x11, 0x11, 0x01, 0x00, 0x01
•
Control Commands List
To view the latest RS232 code, go to the Dell Support site at: support.dell.com.
Specifications
Downloaded From projector-manual.com DELL Manuals
45
Compatibility Modes (Analog/Digital)
Resolution
V. Frequency (Hz)
H. Frequency (KHz)
640X480
59.9
31.5
640X480
75
37.5
640X480
85
43.3
720X400
70.1
31.5
720X400
85
37.9
800X600
60.3
37.9
800X600
75
46.9
800X600
85.1
53.7
848X480
60
31
1024X768
60
48.4
1024X768
75
60
1024X768
85
68.7
1280X720
59.9
44.8
1280X768
59.9
47.8
1280X800
59.8
49.7
1280X1024
60
64
1280X1024
75
80
1280X1024
85
91.1
1360X768
60
47.7
1400X1050
60
65.3
1440X900
59.9
55.9
1680X1050
60
65.3
1600X1200
60
75
46
Specifications
Downloaded From projector-manual.com DELL Manuals
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-9993355).
NOTE: If you do not have an active Internet connection, you can find contact
information on your purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service
options. Availability varies by country and product, and some services may
not be available in your area. To contact Dell for sales, technical support,
or customer service issues:
1
Visit support.dell.com.
2
Verify your country or region in the Choose A Country/Region dropdown menu at the bottom of the page.
3
Click Contact Us on the left side of the page.
4
Select the appropriate service or support link based on your need.
5
Choose the method of contacting Dell that is convenient for you.
Contacting Dell
Downloaded From projector-manual.com DELL Manuals
47
Appendix: Glossary
ANSI LUMENS —A standard for measuring the brightness. It is calculated by
dividing a square meter image into nine equal rectangles, measuring the lux (or
brightness) reading at the center of each rectangle, and averaging these nine
points.
ASPECT RATIO —The most popular aspect ratio is 4:3 (4 by 3). Early television and
computer video formats are in a 4:3 aspect ratio, which means that the width of
the image is 4/3 times the height.
Brightness— The amount of light emitting from a display or projection display or
projection device. The brightness of projector is measured by ANSI lumens.
Color Temperature— The color appearance of white light. Low color
temperature implies warmer (more yellow/red) light while high color temperature
implies a colder (more blue) light. The standard unit for color temperature is
Kelvin (K).
Component Video—A method of delivering quality video in a format that
consists of the luminance signal and two separate chrominance signals and are
defined as Y'Pb'Pr' for analog component and Y'Cb'Cr' for digital component.
Component video is available on DVD players.
Composite Video — A video signal that combines the luma (brightness), chroma
(color), burst (color reference), and sync (horizontal and vertical synchronizing
signals) into a signal waveform carried on a single wire pair. There are three kind of
formats, namely, NTSC, PAL and SECAM.
Compressed Resolution— If the input images are of higher resolution than the
native resolution of the projector, the resulting image will be scaled to fit the
native resolution of the projector. The nature of compression in a digital device
means that some image content is lost.
Contrast Ratio— Range of light and dark values in a picture, or the ratio between
their maximum and minimum values. There are two methods used by the
projection industry to measure the ratio:
1 Full On/Off — measures the ratio of the light output of an all white image (full
on) and the light output of an all black (full off) image.
2 ANSI — measures a pattern of 16 alternating black and white rectangles. The
average light output from the white rectangles is divided by the average light
output of the black rectangles to determine the ANSI contrast ratio.
Full On/Off contrast is always a larger number than ANSI contrast for the same
projector.
48
Glossary
Downloaded From projector-manual.com DELL Manuals
dB— decibel—A unit used to express relative difference in power or intensity,
usually between two acoustic or electric signals, equal to ten times the common
logarithm of the ratio of the two levels.
Diagonal Screen— A method of measuring the size of a screen or a projected
image. It measures from one corner to the opposite corner. A 9FT high, 12FT
wide, screen has a diagonal of 15FT. This document assumes that the diagonal
dimensions are for the traditional 4:3 ratio of a computer image as per the example
above.
DLP®— Digital Light Processing™—Reflective display technology developed by
Texas Instruments, using small manipulated mirrors. Light passes through a color
filter is sent to the DLP mirrors which arrange the RGB colors into a picture
projected onto screen, also known as DMD.
DMD— digital Micro- Mirror Device— Each DMD consists of thousands of
tilting, microscopic aluminum alloy mirrors mounted on a hidden yoke.
DVI-D— Digital Visual Interface-Digital connector.
Focal Length— The distance from the surface of a lens to its focal point.
Frequency— It is the rate of repetition in cycles per seconds of electrical signals.
Measured in Hz (Hertz).
HDCP— High-Bandwidth Digital Content Protection, is a specification developed
by Intel Corporation to protect digital audio/video from copy while acrossing the
DVI/HDMI interface.
HDMI— High Definition Multimedia Interface, delivering uncompressed, alldigital audio/vedio stream.
Hz (Hertz)— Unit of frequency.
Keystone Correction— Device that will correct an image of the distortion
(usually a wide-top narrow-bottom effect) of a projected image caused by
improper projector to screen angle.
Maximum Distance— The distance from a screen the projector can be to cast an
image that is usable (bright enough) in a fully darkened room.
Maximum Image Size— The largest image a projector can throw in a darkened
room. This is usually limited by focal range of the optics.
Minimum Distance— The closest position that a projector can focus an image
onto a screen.
NTSC— National Television Standards Committee. North American standard for
video and broadcasting, with a video format of 525 lines at 30 frames per second.
PAL— Phase Alternating Line. A European broadcast standard for video and
broadcasting, with a video format of 625 lines at 25 frames per second.
Glossary
Downloaded From projector-manual.com DELL Manuals
49
Reverse Image— Feature that allows you to flip the image horizontally. When
used in a normal forward projection environment text, graphics, etc, are
backwards. Reverse image is used for rear projection.
RGB— Red, Green, Blue— typically used to describe a monitor that requires
separate signals for each of the three colors.
S-Video—A video transmission standard that uses a 4-pin mini-DIN connector to
send video information on two signal wires called luminance (brightness, Y) and
chrominance (color, C). S-Video is also referred to as Y/C.
SECAM— A French and international broadcast standard for video and
broadcasting, closely related to PAL but with a different method of sending color
information.
SVGA— Super Video Graphics Array— 800 x 600 pixels count.
SXGA— Super Extended Graphics Array,—1280 x 1024 pixels count.
UXGA— Ultra Extended Graphics Array—1600 x 1200 pixels count.
VGA— Video Graphics Array—640 x 480 pixels count.
WXGA— Wide Extended Graphics Array— 1280x800 pixels count.
XGA— Extended Graphics Array— 1024 x 768 pixels count.
Zoom Lens— Lens with a variable focal length that allows operator to move the
view in or out making the image smaller or larger.
Zoom Lens Ratio— Is the ratio between the smallest and largest image a lens can
projector from a fixed distance. For example, a 1.4:1 zoom lens ratio means that a
10 foot image without zoom would be a 14 foot image with full zoom.
50
Glossary
Downloaded From projector-manual.com DELL Manuals
Index
14, 15, 16
RS232 cable 10, 11
S-video cable 12
To Computer 8, 9
USB to USB cable 8, 9
VGA to VGA cable 8, 9
VGA to YPbPr cable 14
YPbPr to VGA cable 15
YPbPr to YPbPr cable 15
A
Adjusting the Projected Image 18
Adjusting the Projector Height
18
lower the projector
Elevator button 18
Elevator foot 18
Tilt adjustment wheel 18
Adjusting the Projector Zoom and
Focus 19
Focus ring 19
Zoom tab 19
C
Changing the Lamp 41
Connecting the Projector
Composite video cable 13
Connecting a Computer with a
RS232 cable 10, 11
Connecting with a Component
Cable 14, 15
Connecting with a Composite
Cable 13
Connecting with an HDMI
Cable 16
Connecting with an S-video
Cable 12
DVI-D adapter 16
HDMI cable 16
Power cord 8, 9, 10, 11, 12, 13,
Connection Ports
Audio input connector 7
Audio output connector 7
Composite video connector 7
DVI-D input connector 7
Power cord connector 7
RS232 connector 7
Security cable slot 7
S-video connector 7
USB remote connector 7
VGA-A input (D-sub) connector
7
VGA-A output (monitor
loop-through) 7
VGA-B input (D-sub) connector
7
Contact Dell 5, 22, 39
Control Panel 21
D
Dell
Index
Downloaded From projector-manual.com DELL Manuals
51
contacting 47
M
Main Unit 6
Control panel 6
Elevator button 6
Focus ring 6
IR receiver 6
Lens 6
Zoom tab 6
O
On-Screen Display 25
Auto-Adjust 27
Display (in PC Mode) 30
Display (in Video Mode) 31
Input Select 26
Lamp 32
Language 33
Main Menu 26
Others 34
Picture (in PC Mode) 28
Picture (in Video Mode) 29
Set Up 27
P
phone numbers 47
Powering On/Off the Projector
Powering Off the Projector 17
Powering On the Projector 17
R
Remote Control 24
IR receiver 22
S
Specifications
Audio 43
Brightness 43
Color Wheel Speed 43
Contrast Ratio 43
Dimensions 44
Displayable Color 43
Environmental 44
I/O Connectors 44
Lamp 43
Light Valve 43
Noise Level 43
Number of Pixels 43
Power Consumption 43
Power Supply 43
Projection Distance 43
Projection Lens 43
Projection Screen Size 43
Regulatory 44
RS232 Protocol 45
Uniformity 43
Video Compatibility 43
Weight 44
support
contacting Dell 47
T
telephone numbers 47
52
Index
Downloaded From projector-manual.com DELL Manuals
Troubleshooting 37
Contact Dell 37
Index
Downloaded From projector-manual.com DELL Manuals
53