Mitsubishi Electric FR-F800 Instruction manual

INVERTER
FR-A800/F800
Safety Stop Function Instruction Manual
CONTENTS
1. GENERAL DESCRIPTION ............................................ 2
2. INSTALLATION AND WIRING...................................... 3
3. EXAMPLE OF SAFETY SYSTEM CONFIGURATION .... 7
4. TEST AND CHECKING FAILURE ............................... 10
5. SAFETY PARAMETERS OF FR-A800/F800 ................ 11
Compliance with the EU Machinery Directive – Functional Safety
WARNING
 Any misuse of safety function could lead to personal injury or death, property damage, or economic
loss. To ensure that the system complies fully with requirement of safety, make a system-level risk
assessment. Mitsubishi Electric Co. cannot assume responsibility for any system to comply with
safety directive.
CAUTION
 The information of this manual is merely a guide for proper installation.
 Mitsubishi Electric Co. cannot assume responsibility for the compliance or the noncompliance to
any code, national, local or otherwise for the proper installation of this equipment.
 A hazard of personal injury and/or equipment damage exists if codes are ignored during installation.
WARNING
 To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged
before performing any work on the drive. Measure the DC bus voltage at the P(+) and N(-) terminals
or test points (refer to your drive’s User Manual for locations and discharging time). The voltage
must be zero.
WARNING
 The safety stop function do not isolate electrically between drive and motor. To avoid an electric
shock hazard, disconnect/isolate power to the drive and verify to ensure that the voltage is zero
before performing any work on the motor (refer to your drive’s User Manual for discharging time).
1
1
GENERAL DESCRIPTION
Features
Mitsubishi FR-A800/F800 safety stop function prevents a drive from supplying rotational energy to motors. Dual
safety channels ‘S1’ and ‘S2’ cut off the gate-drive power for IGBT to turn off.
FR-A800/F800
SO
R/L1 S/L2 T/L3
Logic
SOC
IGBTs
+24V
PC
Fuse
CPU
RESET
ASIC
Gate
Driver
Gate
Driver
24VDC
S2
G
G
S1
Emergency
stop button
SIC
SD
Safety relay module
/ Safety programmable controller
U V W
M
Fig.1 FR-A800/F800 safety stop function diagram
WARNING
 Disconnecting the power to the gate driver by the safety stop function does not isolate electrically
between drive and motor. To avoid an electric shock hazard, disconnect power to the drive and verify
that the main circuit capacitor voltage is zero (across P and N terminals) before performing any work
on the motor (refer to your drive’s User Manual for discharging time).
Standards
Mitsubishi FR-A800/F800 safety stop function meets the following directives and categories.
ISO13849-1:2008 Category 3/PLd
IEC62061:2005 / IEC61800-5-2:2007 / IEC61508 SIL2
IEC60204-1:2010 / IEC61800-5-2:2007 Stop category 0
WARNING
 The misuse of safety function leads to personal injury or death, property damage, or economic loss.
To ensure that the system complies fully with requirement of safety, make a system-level risk
assessment. Mitsubishi Electric Co. cannot assume responsibility for any system to comply with
safety directive.
2
GENERAL DESCRIPTION
2
INSTALLATION AND WIRING
CAUTION
 The following information is merely a guide for proper installation.
 Mitsubishi Electric Co. cannot assume responsibility for the compliance or the noncompliance to
any code, national, local or otherwise for the proper installation of this equipment.
 A hazard of personal injury and/or equipment damage exists if codes are ignored during installation.
CAUTION
 Ensure the safety relay unit and the FR-A800/F800 unit is mounted closely in enclosure meeting IP54
and all interconnection wiring is short and protected against open and short circuit faults. Refer ISO/
IEC13849-2.
Installation
Mitsubishi FR-A800/F800 safety stop function should be used under following condition and environment.
Table.1 The condition and environment for using safety stop function
Item
Surrounding air
temperature
Condition
LD, ND, HD 
-10ºC to +50ºC (non-freezing)
SLD
-10ºC to +40ºC (non-freezing)
Storage temperature
-20ºC to +65ºC 
Ambient humidity
With circuit board coating (conforming to IEC60721-3-3 3C2/3S2): 95% RH or
less (non-condensing),
Without circuit board coating: 90% RH or less (non-condensing)
Vibration
5.9m/s2 or less at 10 to 55Hz (directions of X, Y, Z axes)
Altitude
Maximum 2500 above sea level 
Atmosphere
Indoors (free from corrosive gas, flammable gas, oil mist, dust and dirt)
Over voltage category
III or less
Pollution degree
II or less
Mounting
Wall mounting / vertical orientation
 The ND and HD ratings can be selected only for the FR-A800.
 Temperature applicable for a short time, e.g. in transit.
 For the installation at an altitude above 1,000 m (3280.80 feet) up to 2,500 m (8202 feet), derate the rated current 3% per 500
m (1640.40 feet).
INSTALLATION AND WIRING
3
CAUTION
 In order to meet safety stop, an approved safety relay unit to ISO13849-1 safety category 3 or better
shall be used in conjunction with FR-A800/F800 as shown in example. In addition, all other
components with in the safety stop loop shall be ‘safety approved’ types.
WARNING
 To avoid an electric shock hazard, insert the magnetic contactor (MC) between power source and
drive.
 Open the contact of MC and keep away from drive for discharging time (refer to your drive’s User
Manual for information) before performing any work on the drive. And verify that the voltage on the
bus capacitors has discharged before Measuring the DC bus voltage at the P(+) and N(-) terminals or
test points (refer to your drive’s User Manual for locations). The voltage must be zero.
CAUTION
 To avoid systematic faults, a test even for faulty demands of the safety function has to be performed
in order to check the correct function of the monitor signal. This test shall be carried out at system
installation, any software changes, parameterization changes, and/or at least once per year. Refer to
‘4. Test and checking failure’.
●Wiring
The safety related terminals are described in Table.2 and Table.3
Table.2 The safety related terminals
Terminal
symbol
S1
Description 
For input of safety stop channel 1.
S1-SIC is
OFF: In safety stop mode.
ON: Non safety stop mode.
S2
For input of safety stop channel 2.
S2-SIC is
OFF: In safety stop mode.
ON: Non safety stop mode.
SIC
Common terminal for S1 terminal and S2 terminal.
SO
As output for failure detection and alarm. SO terminal type is
‘Open collector output’.
SO-SOC is
OFF: Detect failure or alarm.
ON: No failure detected.
Note: This terminal cannot be used to output safety outputs in a
safety system. This terminal can be used for alarm or to
prevent restart only, no other safety function.
SOC
Common terminal for SO terminal.
 Specifications for conforming safety standards.
 ON: The transistor is conducted. OFF: The transistor is not conducted.
4
INSTALLATION AND WIRING
Rating 
Input resistance: 4.7kΩ
Input current : 4 to 6 mADC
(In case of 24VDC input)
Load: 24VDC/0.1A max.
Voltage drop: 3.4V max.
(In case of ‘ON’ state)
Table.3 Truth table of safety related signals
Internal
safety
circuit
status
Input
power
OFF
ON
Input terminal , 
S1
S2
Output
terminal
Inverter running status
SO
Operation panel
indication
E.SAF 
Not
displayed
Not
displayed
Displayed
Displayed
Not
displayed



OFF
Output shutoff (Safe state)
Normal
ON
ON
ON 
Drive enabled
Normal
Normal
ON
OFF
OFF
ON
OFF 
OFF 
Output shutoff (Safe state)
Output shutoff (Safe state)
Normal
OFF
OFF
ON 
Output shutoff (Safe state)
Fault
ON
ON
OFF
Output shutoff (Safe state)
Displayed
Fault
Fault
Fault
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
Output shutoff (Safe state)
Output shutoff (Safe state)
Output shutoff (Safe state)
Displayed
Displayed
Displayed
SA 
Not
displayed
Not
displayed
Displayed
Displayed
Displayed
Not
displayed 
Displayed
Displayed
Displayed
 ON: The transistor is conducted. OFF: The transistor is not conducted.
 When not using the safety stop function, short across terminals S1 and PC, S2 and PC, and SIC and SD to use the inverter.
(In the initial status, terminals S1 and PC, S2 and PC, and SIC and SD are respectively shorted with shorting wires.)
 If any of the protective functions shown in the following table is activated, the terminal SO turns OFF.
Error definition
Option fault.
Operation panel indication
Error definition
Operation panel indication
E.OPT
24 VDC power fault
E.P24
Communication option fault
E.OP1
Safety circuit fault
E.SAF
Parameter storage device fault
E.PE
Overspeed occurrence
Retry count excess
E.RET
Parameter storage device fault
E.PE2
Operation panel power supply short circuit/
RS-485 terminals power supply short
circuit
CPU fault
Internal circuit fault
E.OS
E.CPU
E.5 to E.7
E.13
E.CTE
 If the internal safety circuit is operated normally, the terminal SO remains ON until E.SAF is displayed, and the terminal SO
turns OFF when E.SAF is displayed.
 SA is displayed when the terminals S1 and S2 are identified as OFF due to the internal safety circuit failure.
 If another fault occurs at the same time as E.SAF, the other fault can be displayed.
 If another warning occurs at the same time as SA, the other warning can be displayed.
NOTE
• The response time from safety stop signal input to drive shutoff (safe state) is faster than 8ms.
• Hold the ON or OFF status for 2ms or longer to input signal to terminal S1 or S2.
Signal input shorter than 2ms is not recognized.
INSTALLATION AND WIRING
5
●Wire and ferrule specification
Table.4 Wire and ferrule specification
Wire size (mm2)
Ferrule with insulation collar 
0.3 / 0.5
AI 0,5-10WH
0.75
AI 0,75-10GY
1
AI 1-10RD
1.25 / 1.5
AI1,5-10BK
0.75 (combined 2 wire)
AI TWIN 2 X 0,75-10GY
Crimping tool name 
CRIMPFOX 6
 Ferrules and tools are distributed by Phoenix Contact.
●Jumper cable
The jumper cable between S1,S2 and PC terminal between SIC and SD terminal has been installed in the factory
as shown in Fig.2.
2
5
4
1 F/C +24 SD So SOC SD SIC S1 S2 PC
AM 5 10E 10 SE SE RUN SU IPF OL FU
A1
B1
C1
A2
B2
C2
PC RL RM RH RT AU STP MRS RES SD SD STF STR JOG CS
Terminal block of FR-A800/F800
Fig.2. Short wire
Before connecting safety input wire to S1,S2 and SIC terminal, remove this jumper cable.
6
INSTALLATION AND WIRING
3
EXAMPLE OF SAFETY SYSTEM
CONFIGURATION
●FR-A800/F800 configuration example
R/L1 S/L2 T/L3
SO
Logic
SOC
RESET
START
STF
STOP
STOP
S2
Emergency
stop button
CPU
ASIC
Gate
Driver
Gate
Driver
24V
DC
+24V
X0 COM0 X1 COM1 XS0 XS1
IGBTs
Z00 Z10 Z20
S1
Internal
Safety
Circuit
24V
DC
K1
G
K2
24G
G
SIC
SD
Z01 Z11 Z21
+24V
Safety relay module
MELSEC QS90SR2SN-Q
Fuse
PC*1
FR-A800/F800
U
V
W
M
 If the control logic is SINK logic, the common terminal is terminal SD.
Fig.3 Safety system example with FR-A800/F800
NOTE
• When starting up the system’s operation, press the RESET switch to reset the safety stop function first,
then turn ON the START switch to run the motor.
• In the above configuration, after reset of emergency stop button, drive will be in safe-state until RESET
switch is pressed.
CAUTION
 To prevent restart in case of recovering from input power loss of drive, 3-wired connection for
START/STOP control is recommended. In case of 2-wire connection and using latching type switch
to short between STF and SD/PC for starting, ensure the compliance with safety requirement for the
restarting when the drive recover from input power loss.
EXAMPLE OF SAFETY SYSTEM CONFIGURATION
7
●Multiple inverter configuration example
R/L1 S/L2 T/L3
SO
Logic
SOC
RESET
S2
Emergency
stop button
CPU
ASIC
24V
DC
+24V
X0 COM0 X1 COM1 XS0 XS1
Gate
Driver
Gate
Driver
IGBTs
Z00 Z10 Z20
S1
Internal
Safety
Circuit
24V
DC
K1
G
G
SIC
K2
SD
+24V
Fuse
24G
Z01 Z11 Z21
PC
Safety relay module
MELSEC QS90SR2SN-Q
FR-A800/F800
U
V
W
M
R/L1 S/L2 T/L3
SO
Logic
SOC
S2
CPU
ASIC
Gate
Driver
Gate
Driver
IGBTs
S1
G
G
SIC
SD
+24V
Fuse
PC
FR-A800/F800
U
V
W
M
Fig.4 When using multiple safety stop function inverters (FR-A800/F800)
NOTE
• Some models cannot be used together because their control logics are different. Refer to the SAFETY
STOP FUNCTION MANUAL of each model.
8
EXAMPLE OF SAFETY SYSTEM CONFIGURATION
●Safety controller configuration example
WS0
-CPU0
WS0-CPU0
WS0
-XTIO
WS0-XTIO
FLEXBUS+
FLEXBUS+
24V
24V
I1
I1
I2
I2
I3
I3
I4
I4
X1
Application
Emergency
stop button
I5
I5
I6
I6
RESET
0V
0V
I7
I7
I8
I8
FR-A800/F800
X2
SO
R/L1 S/L2 T/L3
Logic
SOC
A1(24V)
FLEXBUS+
FLEXBUS+
A1(24V)
Q1
A2(0V)
Application
Q2
Q3
IGBTs
+24V
24VDC
PC
Fuse
CPU
S2
ASIC
Gate
Driver
G
Gate
Driver
G
S1
SIC
Q4
SD
A2(0V)
U V W
M
MITSUBISHI safety controller MELSEC-WS series
CPU module
WS0-CPU0
Safety I/O combined module
WS0-XTIO
Fig.5 Safety system example with FR-A800/F800
NOTE
• When starting up the system’s operation, press the RESET switch to reset the safety stop function first.
• In the above configuration, after reset of emergency stop button, drive will be in safe-state until RESET
switch is pressed.
EXAMPLE OF SAFETY SYSTEM CONFIGURATION
9
4
TEST AND CHECKING FAILURE
CAUTION
 To avoid systematic faults, a test even for faulty demands of the safety function has to be performed
in order to check the correct function of the monitor signal. This test shall be carried out at system
installation, any software changes, parameterization changes, and/or at least once per year.
I/O status and failure
FR-A800/F800 safety related I/O status obeys the following truth table.
Table.5 Truth table of safety related signals
Internal
safety
circuit
status
Input
power
OFF
ON
Input terminal , 
S1
S2
Output
terminal
Inverter running status
SO
Operation panel
indication
E.SAF 
Not
displayed
Not
displayed
Displayed
Displayed
Not
displayed



OFF
Output shutoff (Safe state)
Normal
ON
ON
ON 
Drive enabled
Normal
Normal
ON
OFF
OFF
ON
OFF 
OFF 
Output shutoff (Safe state)
Output shutoff (Safe state)
Normal
OFF
OFF
ON 
Output shutoff (Safe state)
Fault
ON
ON
OFF
Output shutoff (Safe state)
Displayed
Fault
Fault
Fault
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
Output shutoff (Safe state)
Output shutoff (Safe state)
Output shutoff (Safe state)
Displayed
Displayed
Displayed
SA 
Not
displayed
Not
displayed
Displayed
Displayed
Displayed
Not
displayed 
Displayed
Displayed
Displayed
 ON: The transistor is conducted. OFF: The transistor is not conducted.
 When not using the safety stop function, short across terminals S1 and PC, S2 and PC, and SIC and SD to use the inverter.
(In the initial status, terminals S1 and PC, S2 and PC, and SIC and SD are respectively shorted with shorting wires.)
 If any of the protective functions shown in the following table is activated, the terminal SO turns OFF.
Error definition
Option fault.
Operation panel indication
Error definition
Operation panel indication
E.OPT
24 VDC power fault
E.P24
Communication option fault
E.OP1
Safety circuit fault
E.SAF
Parameter storage device fault
E.PE
Overspeed occurrence
Retry count excess
E.RET
Parameter storage device fault
E.PE2
Operation panel power supply short circuit/
RS-485 terminals power supply short
circuit
CPU fault
Internal circuit fault
E.OS
E.CPU
E.5 to E.7
E.13
E.CTE
 If the internal safety circuit is operated normally, the terminal SO remains ON until E.SAF is displayed, and the terminal SO
turns OFF when E.SAF is displayed.
 SA is displayed when the terminals S1 and S2 are identified as OFF due to the internal safety circuit failure.
 If another fault occurs at the same time as E.SAF, the other fault can be displayed.
 If another warning occurs at the same time as SA, the other warning can be displayed.
NOTE
• The response time from safety stop signal input to drive shutoff (safe state) is faster than 8ms.
• Hold the ON or OFF status for 2ms or longer to input signal to terminal S1 or S2.
Signal input shorter than 2ms is not recognized.
10
TEST AND CHECKING FAILURE
Diagnostic
If the failure detected, FR-A800/F800 output alarm signal and indicate ‘E.SAF’ at the display.
In case of FR-A800/F800 output the alarm, please take following action.
1) Check the S1-SIC and S2-SIC input signal logic is the same. If these are different logic, collect the input signal
and reset the FR-A800/F800.
2) Disconnect the wire from S1, S2, SIC terminal, then reset or power-off and on. If the ‘SA’ letter is flashed up at
display, there is failure in system except FR-A800/F800. But, still ‘E.SAF’ is displayed and alarm output, there
is malfunction on FR-A800/F800.
Self diagnostic test
FR-A800/F800 does the self-diagnostic test on the power-ON.
If FR-A800/F800 output alarm (SA, E.SAF) at power-up, please take the action described in ‘Diagnostic’ at
above.
Test procedure for functionality
As depicted ‘CAUTION’ in above, the test for the functionality is important.
Please do the test following procedure.
1) Please make each state of S1-SIC and S2-SIC depicted at Table.5.
2) If there is any different state from Table.5, FR-A800/F800 has some malfunction.
3) If there is no different state from Table.5, check the systematic performance, such as, press the emergency
switch, press the start/restart button at the failure detected (SO-SOC opened), and so on.
4) Finally clear the error record of the FR-A800/F800 (see the user manual how to clear the error record).
5
SAFETY PARAMETERS OF FR-A800/F800
The safety parameters of FR-A800/F800 are depicted as follows.
Table.6 Safety parameters of FR-A800/F800
Parameter
Value
PFDAVG
5.16x10-4
PFHD
5.89x10-9
PL
d
MTTFD
670 years
DCAVG
60%
SAFETY PARAMETERS OF FR-A800/F800
11
REVISIONS
Print Date
Manual Number
Apr. 2013
BCN-A23228-001(E)
Jun. 2013
BCN-A23228-001-A(E)
Jul. 2014
BCN-A23228-001-B(E)
12
BCN-A23228-001-B(E)
Revision
First edition
Modification
● Multiple inverter configuration example
Compatibility with the FR-F800 series
HEADQUARTERS
EUROPEAN REPRESENTATIVES
EUROPEAN REPRESENTATIVES
EUROPEAN REPRESENTATIVES
MITSUBISHI ELECTRIC
EUROPE
EUROPE B.V.
German Branch
Gothaer Straße 8
D-40880 Ratingen
Phone: +49 (0) 21 02 / 486-0
Hotline: +49 2102 1805 000-765 /-766
Fax: +49 (0) 21 02 / 4 86-1 12 0
e mail: megfa-mail@meg.mee.com
www.mitsubishi-automation.com
GEVA
AUSTRIA
Wiener Straße 89
A-2500 Baden
Phone: +43 (0) 2252 / 85 55 20
Fax: +43 (0) 2252 / 488 60
e mail: office@geva.co.at
MITSUBISHI ELECTRIC
IRELAND
EUROPE B.V.-Irish Branch
Westgate Business Park
Ballymount
IRL-Dublin 24
Phone: +353 (0) 1 / 419 88 00
Fax: +353 (0) 1 / 419 88 90
e mail: sales.info@meuk.mee.com
Beijer Electronics AB
SWEDEN
Box 426
S-20123 Malmö
Phone: +46 (0) 40 / 35 86 00
Fax: +46 (0) 40 / 93 23 02
e mall: ——
MITSUBISHI ELECTRIC
FRANCE
FRANCE
25, Boulevard des Bouvets
F-92741 Nanterre Cedex
Phone: +33 1 55 68 55 68
Fax: +33 1 49 01 07 25
e mail: factory.automation@fra.mee.com
MITSUBISHI ELECTRIC
ITALY
EUROPE B.V.
Italian Branch
C.D. Colleoni-P. Perseo lng. 2
Via Paracelso 12
I-20041 Agrate Brianza (Ml)
Phone: +39 (0) 39 / 60 53 1
Fax: +39 (0) 39 / 60 53 312
e mail: factory.automation@it.mee.com
MITSUBISHI ELECTRIC
SPAIN
EUROPE B.V.
Pol. lnd. Can Magi-C.
Calle Joan Buscallá, 2-4 AC 420
E-08190 Sant Cugat del Vallés
Phone: +34 (9) 3 / 565 31 31
Fax: +34 (9) 3 / 589 29 48
MITSUBISHI ELECTRIC
UK
EUROPE B.V.
UK Branch
Travellers Lane
Hatfield, Hertfordshire, AL10 8 XB
Phone: +44 (0) 1707 / 27 61 00
Fax: +44 (0) 1707 / 27 86 95
MITSUBISHI ELECTRIC
JAPAN
CORPORATION
Tokyo Bldg.
2-7-3 Marunouchi Chiyoda-Ku
Tokyo 100-8310
Phone: +81 (0) 3 / 32 18 31 76
Fax: +81 (0) 3 / 32 18 24 22
MITSUBISHI ELECTRIC
AUTOMATION
500 Corporate Woods Parkway
Vernon Hills, Illinois 60061
Phone: +1 (0) 847 / 478 21 00
Fax: +1 (0) 847 / 478 03 27
USA
Getronics b.v.
BELGIUM
Control Systems
Pontbeeklaan 43
B-1731 Asse-Zellik
Phone: +32 (0) 2 / 4 67 17 51
Fax: +32 (0) 2 / 4 67 17 45
e mail: infoautomation@getronics.com
TELECON CO.
BULGARlA
4, A. Ljapchev Blvd.
BG-1756 Sofia
Phone: +359 92 / 97 44 05 8
Fax: +359 92 / 97 44 06 1
e mail: ——
AutoCont
CZECHIA
Control Systems s.r.o.
Nemocnicni 12
CZ-70200 Ostrava 2
Phone: +420 (0) 69 / 615 21 11
Fax: +420 (0) 69 / 615 21 12
e mail: ——
louis poulsen
DENMARK
industri & automation
Geminivej 32
DK-2670 Greve
Phone: +45 (0) 43 / 95 95 95
Fax: +45 (0) 43 / 95 95 91
e mail: lpia@lpmail.com
UTU Elektrotehnika AS
Pärnu mnt. 160i
EE-10621 Tallinn
Phone: +372 6 / 51 72 80
Fax: +372 6 / 51 72 88
e mail: utu@utu.ee
ESTONIA
ALFATRADE LTD.
MALTA
99 Paola Hill
Paola PLA 08
Phone: +356 / 697816
Fax: +356 / 697817
e mail: paul.licari@alfatrx.com
Getronics bv
NETHERLANDS
Control Systems
Donauweg 10
NL-1043 AJ-Amsterdam
Phone: +31 (0) 20 / 586 15 92
Fax: +31 (0) 20 / 586 19 27
e mail: infoautomation@getronics.com
Beijer Electronics AS
NORWAY
Teglverksveien 1
N-3002 Drammen
Phone: +47 (0) 32 / 24 30 00
Fax: +47 (0) 32 / 84 85 77
e mall: ——
MPL Technology SP.Z.o.o
POLAND
ul.Wroclawska 53
PL-30-011 Kraków
Phone: +48 (0) 12 / 632 28 85
Fax: +48 (0) 12 / 632 47 82
e mail: krakow@mpl.com.pl
Sirius Trading&Services srl ROMANIA
Bd. Ghica nr. 112, BI. 41
RO-72335 Bucaresti 2
Phone: +40 (0) 1 / 210 55 11
Fax: +40 (0) 1 / 210 55 11
e mail: sirius_t_s@fx.ro
URHO TUOMINEN OY
FINLAND
Hevoshaankatu 3
FIN-28600 Pori
Phone: +358 (0) 2 / 55 08 00
Fax: +358 (0) 2 / 55 088 41
e mall: ——
ACP AUTOCOMP a.s.
SLOVAKIA
Chalupkova 7
SK-81109 Bratislava
Phone: +421 (0) 7 592 22 54
Fax: +421 (0) 7 592 22 48
e mall: ——
UTECO A.B.E.E.
GREECE
5, Mavrogenous Str.
GR-18542 Piraeus
Phone: +30 (0) 1 / 42 10 050
Fax: +30 (0) 1 / 42 12 033
e mall: uteco@uteco.gr
lNEA d.o.o.
SLOVENlA
Ljubljanska 80
SI-1230 Dom z ale
Phone: +386 (0) 17 21 80 00
Fax: +386 (0) 17 24 16 72
e mail: inea@inea.si
ECONOTEC AG
SWITZERLAND
Postfach 282
CH-8309 Nürensdorf
Phone: +41 (0) 1 / 838 48 11
Fax: +41 (0) 1 / 838 48 12
e mall: ——
GTS
TURKEY
Darülaceze Cad. No. 43A KAT: 2
TR-80270 Okmeydani-Istanbul
Phone: +90 (0) 212 / 320 1640
Fax: +90 (0) 212 / 320 1649
e mall: ——
EURASIAN REPRESENTATIVES
MITSUBISHI ELECTRIC
RUSSIA
EUROPE B.V.
12/1 Goncharnaya St, suite 3C
RUS-109240 Moskow
Phone: +7 (0) 95 / 915-8624/02
Fax: +7 (0) 95 / 915-8603
e mall: ——
STC Drive Technique
RUSSIA
Poslannikov per., 9, str. 1
RUS-107005 Moskow
Phone: +7 (0) 95 / 786 21 00
Fax: +7 (0) 95 / 786 21 01
e mall: ——
JV-CSC Automation
UKRAINE
15, M. Raskovoyi St., Floor 10,
Office 1010
U-02002 Kiev
Phone: +380 (4) 4 / 238 83 16
Fax: +380 (4) 4 / 238 83 17
e-Mail: mkl@csc-a.kiev.ua
MIDDLE EAST REPRESENTATIVE
SHERF Motion Techn. LTD
ISRAEL
Rehov Hamerkava 19
IL-58851 Holon
Phone: +972 (0) 3 / 559 54 62
Fax: +972 (0) 3 / 556 01 82
e mall: ——
HEAD OFFICE: TOKYO BUILDING 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
BCN-A23228-001-B(E)(1407)MEE Printed in Japan
Specifications subject to change without notice.