Product information | European Touch ALTERA Product specifications

European Touch - Limited Conditional Warranty

European Touch Holdings, Inc. ("European Touch") conditionally warrants your whirlpool pedicure spa (the

"Pedicure Spa") in accordance with the terms and conditions set forth below for a period of one (1) year commencing on the original date of shipment of the Pedicure Spa to you. The warranty only applies to the

Pedicure Spa's original end-user owner or customer (the "Customer"). This Conditional Warranty is non-

transferable and replaces any warranties previously published by European Touch.

If examination of the Pedicure Spa by European Touch during the applicable warranty period shows it to have a defect in material or workmanship, European Touch will, at its option, repair or replace the defective component or part thereof. Further, European Touch may, at its discretion, replace a defective component or part with a refurbished component or part, or may replace the Pedicure Spa with a refurbished pedicure spa. If

European Touch elects to replace the Pedicure Spa, the replacement pedicure spa must be comparable in style and size to the Pedicure Spa. The customer shall bear all charges incurred for the shipment to it of a replacement spa or components or parts. This limited warranty also covers the cost of all labor incurred in repairing defects in the Pedicure Spa or repairing or replacing any of its defective components or parts, when the work is done by a pre-authorized European Touch preferred service provider; provided, however, that labor is not covered for those parts listed on attached Exhibit A as provided below. Cost of repair by any nonauthorized service provider is not reimbursable and may void this warranty.

The foregoing limited warranty does not apply:

• To the Pedicure Spa, or any components or parts thereof, if subjected to misuse or neglect or if accidentally or intentionally damaged.

• To the Pedicure Spa, or any components or part, if altered or modified in any way.

• To any expenses incurred by the Customer or any third party, including labor or material, during investigation, removal or reinstallation of the Pedicure Spa or any defective components or parts.

• To any damage to or impairment of the Pedicure Spa, or any components or parts thereof, caused by any casualty, including without limitation, accident, fire, wind, floods, acts of nature or attempted theft.

• To any workmanship of a fabricator (other than European Touch) or installer of the Pedicure Spa.

• If damage to pump parts and/or motor parts is due to obstructed plumbing.

• If the Pedicure Spa is removed from its place of initial installation.

• To staining, fading, or discoloration of any portion of the Pedicure Spa caused by water additives or improper water treatment.

• To staining, fading or discoloration of the Pedicure Spa's upholstered seat, armrests or footrests.

• To malfunctions or damage caused by improper installation of the Pedicure Spa, including, but not limited to, failure to meet state or local plumbing, electrical and building codes and other applicable laws and regulations.

• To damage resulting from a person standing in the Pedicure Spa's basin or other similar stress to that basin.

• To freight damage.

• To damage incurred to the Pedicure Spa while in possession of any party other than European Touch.

• To any special costs imposed by any landlord or other party controlling the building in which the

Pedicure Spa is located such as the cost of fidelity bonding or unique licensing requirements, all of which costs shall be borne by the Customer.

Doc ID: 12080006 Rev: A Page 1 Technical Support: 800-626-6912 Date: 2/19/10

• To any labor costs to install those parts listed on attached Exhibit A which consist of items which do not require the skills of a trained technician to install.

• This forgoing conditional limited warranty is also conditional upon:

• The Pedicure Spa being installed by a licensed professional in accordance with European Touch's installation instructions and applicable state and local plumbing, electrical and building codes and other applicable laws and regulations.

• Use of the Pedicure Spa in compliance with all regulatory and industry guidelines (including without limitation, UL and NSF guidelines and applicable state and local plumbing, electrical and building codes and other applicable laws and regulations)

• Use of parts and components which are either genuine European Touch parts and components or are parts and components approved for use by European Touch. Failure to comply with this requirement may also lead to voiding of the Pedicure Spa's UL and NSF approvals and applicable state and local plumbing and other certifications which could impact compliance with state and local codes and regulations as well as insurance coverage requirements.

• The proper use of cleaning and sanitizing solutions in accordance with the instruction labels provided by

European Touch or the requirements of applicable law. Repeated use of concentrated chlorine or other chemicals will void this limited warranty, except to the extent such use is required by the provisions applicable law.

• Avoidance of the use of ionic detox machines that submit any metallic part to reverse electroplating; this use will destroy plated parts and void the warranty.

• Shipment, if requested, to European Touch of Pedicure Spa parts or components thought to be defective.

Parts or components may only be returned if authorized in advance by European Touch. All returns must be freight prepaid.

• Determination by European Touch, in its reasonable discretion, that there exists a defect in material or workmanship.

Repair or replacement of any part or component under this Limited Warranty, or furnishing a replacement pedicure spa, shall not extend the duration of the warranty with respect to such repaired or replaced part beyond the stated warranty period. When a part or component is replaced, it will be under warranty for 90 days, or for the remaining life of original warranty, whichever period is greater.

Customer agrees by using the Pedicure Spa that

• THE OBLIGATION OF EUROPEAN TOUCH SHALL NOT EXTEND TO INDIRECT OR

CONSEQUENTIAL DAMAGES OR INJURY WHICH MAY RESULT FROM SUCH USE

• That the obligations of European Touch are limited to those set forth herein.

• This warranty is limited to the original owner/end-user and is non-transferable.

• European Touch shall not be liable for any other obligations or liabilities, including, but not limited to: obligations or liabilities arising out of breach of contract or warranty, negligence, or other tort or any theory of strict liability with respect to the Pedicure Spa or parts or components thereof or any acts or omissions of European Touch

• Any assistance European Touch provides to the Customer outside of terms, limitations, or exclusions of this limited warranty will not constitute a waiver of any of the foregoing terms, limitations, or exclusions, nor will such assistance extend or revive the warranty.

Doc ID: 12080006 Rev: A Page 2 Technical Support: 800-626-6912 Date: 2/19/10

THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EITHER EXPRESS OR

IMPLIED, AND ALL SUCH OTHER WARRANTIES, INCLUDING WITHOUT LIMITATION,

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, ARE HEREBY DISCLAIMED AND EXCLUDED FROM THIS LIMITED WARRANTY.

NO DEALER OR OTHER PERSON HAS ANY AUTHORITY TO BIND EUROPEAN TOUCH TO

CHANGES OR ADDITIONS TO THIS WARRANTY. ACCORDINGLY, EUROPEAN TOUCH IS

NOT RESPONSIBLE FOR ANY SUCH CHANGES OR ADDITIONS.

IN NO EVENT SHALL EUROPEAN TOUCH BE LIABLE IN ANY WAY FOR ANY

CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OF ANY NATURE WHATSOEVER,

OR FOR ANY AMOUNTS IN EXCESS OF THE SELLING PRICE OF THE PEDICURE SPA OR ANY

COMPONENTS OR PARTS THEREOF FOUND TO BE DEFECTIVE. THIS LIMITED WARRANTY

GIVES THE CUSTOMER SPECIFIC LEGAL RIGHTS. THE CUSTOMER MAY ALSO HAVE

OTHER RIGHTS WHICH MAY VARY BY EACH JURISDICTION.

Should your Pedicure Spa require service due to a defect or malfunction, please contact:

European Touch – Technical Support

800.626.6912 | 414.357.7016 | f: 414.357.6360 email: [email protected]

website: europeantouch.com

Exhibit A for 25th Anniversary Murano Spa Extended Service Contract And Limited

Warranty Document

Parts for which Labor/Service is NOT COVERED.

The following spa components are simple to replace and do not require a service technician. Therefore, though the part is covered under the guidelines of the warranty agreement, payment to a service technician for labor is not.

25th Anniversary Murano Spa

Body Panels

Clean Touch Impeller

Clean Touch Impeller Cover

Clean Touch Impeller Housing

Clean Touch Sensors

Cushion Replacement

Faucet Cartridge

Footpads

Leveling feet

On/Off / Drain button

PDP pump

Doc ID: 12080006 Rev: A Page 3 Technical Support: 800-626-6912 Date: 2/19/10

Inspection of the 25th Anniversary Murano Spa

Inspect the 25th Anniversary Murano Spa™ and packaging. If any damage to the 25th Anniversary Murano

Spa™ or its packaging is visible, please contact your local 25th Anniversary Murano Spa™ reseller or call

European Touch Customer Support at 800-626-6912.

Important Information

Serial Number: ____________________________

Installed By: ______________________________

Installation Date: __________________________

Serial Number Location

The serial number of your 25th Anniversary Murano Spa™ is needed when calling European Touch for any parts requests or warranty claims. It is located inside the left armrest door.

Doc ID: 12080006 Rev: A Page 4 Technical Support: 800-626-6912 Date: 2/19/10

TABLE OF CONTENTS

EUROPEAN TOUCH - LIMITED CONDITIONAL WARRANTY............................................................................... 1

INSPECTION OF THE 25TH ANNIVERSARY MURANO SPA................................................................................... 4

S ERIAL N UMBER L OCATION .................................................................................................................................................................. 4

INTRODUCTION................................................................................................................................................................. 6

P RECAUTIONS ........................................................................................................................................................................................ 6

IMPORTANT SAFETY INSTRUCTIONS........................................................................................................................ 7

DANGER ............................................................................................................................................................................... 8

WARNINGS .......................................................................................................................................................................... 8

PRODUCT SPECIFICATIONS.......................................................................................................................................... 9

25 TH A NNIVERSARY M URANO S PA S PECIFICATIONS ............................................................................................................................. 9

I MPORTANT R EQUIREMENTS .................................................................................................................................................................. 9

P LUMBING & C ERTIFICATIONS .............................................................................................................................................................. 9

C OMMONWEALTH OF M ASSACHUSETTS P LUMBING & C ERTIFICATIONS ................................................................................................ 9

INSTALLATION INSTRUCTIONS................................................................................................................................. 11

E LECTRICAL S ERVICE .......................................................................................................................................................................... 11

W ATER S UPPLY ................................................................................................................................................................................... 11

D RAIN F ACILITIES ................................................................................................................................................................................ 11

L OCATION /P OSITIONING ...................................................................................................................................................................... 11

FEATURES OF THE 25TH ANNIVERSARY MURANO SPA .................................................................................... 12

B ASIN M ATERIAL ................................................................................................................................................................................. 12

C USHIONED L EG S UPPORTS ................................................................................................................................................................. 12

TECHNICIAN OPERATION GUIDE ............................................................................................................................. 12

F ILLING S PA ......................................................................................................................................................................................... 12

W ATER MOVEMENT ON / OFF ................................................................................................................................................................. 12

B ASIN U P AND B ASIN D OWN ............................................................................................................................................................... 12

D RAIN W ATER ..................................................................................................................................................................................... 12

AIR CARESS RELAXATION & REMOTE CONTROL FOR 25 TH ANNIVERSARY MURANO .......................... 13

R EMOTE C ONTROL F EATURES ............................................................................................................................................................. 13

A IR R ELAXATION S YSTEM ................................................................................................................................................................... 14

ROLLER MASSAGE & REMOTE CONTROL FOR 25TH ANNIVERSARY MURANO....................................... 15

R EMOTE C ONTROL F EATURES ............................................................................................................................................................. 15

R OLLER / V IBRATION M ASSAGE S YSTEM ............................................................................................................................................ 16

REMOVING THE CLEAN TOUCH ASSEMBLY FROM THE BASIN FLOOR...................................................... 17

PEDICURE PRODUCT GUIDELINES........................................................................................................................... 17

CLEANING AND DISINFECTING PEDICURE EQUIPMENT.................................................................................. 18

A FTER EVERY CLIENT .......................................................................................................................................................................... 18

A T THE END OF EVERY DAY ................................................................................................................................................................. 18

A T LEAST ONCE EACH WEEK ................................................................................................................................................................ 18

A DDITIONAL I NFORMATION ABOUT D ISINFECTANTS AND D ETERGENT C LEANERS .............................................................................. 19

EXPLODED PART VIEWS .............................................................................................................................................. 20

S EAT A SSEMBLY .................................................................................................................................................................................. 20

R IGHT S IDE M ANICURE T RAY A SSEMBLY ........................................................................................................................................... 20

L EFT S IDE M ANICURE T RAY A SSEMBLY ............................................................................................................................................. 21

S EAT T RACK A SSEMBLY ...................................................................................................................................................................... 21

B ASIN A SSEMBLY ................................................................................................................................................................................ 22

B ELLY P AN A SSEMBLY ........................................................................................................................................................................ 23

P OWER D RAIN P UMP (PDP) A SSEMBLY ............................................................................................................................................... 23

TROUBLE SHOOTING GUIDE ...................................................................................................................................... 24

Doc ID: 12080006

1-414-357-6360 [email protected] [email protected] www.europeantouch.com

Rev: A Page 5 Technical Support: 800-626-6912 Date: 2/19/10

Introduction

European Touch would like to thank you for your purchase of the 25th Anniversary Murano Spa, the world’s finest pedicure spa. From its beautifully crafted glass vestibule and sleek European styling, the 25th

Anniversary Murano Spa system surpasses every industry standard for performance and comfort.

With the 25th Anniversary Murano Spa, you can also be assured of uncompromised cleaning standards with our patented Clean Touch Pipe-Free technology, which replaces traditional-style jets and pipes that can harbor bacteria. The Clean Touch Pipe-Free technology features a convenient, removable housing to allow easy cleaning. To learn more about cleaning and maintaining your 25th Anniversary Murano Spa, please refer to the cleaning instructions on page 18.

If you do experience any problems or have any questions regarding your 25th Anniversary Murano Spa, please refer to the troubleshooting guide in the appendix or call 800-626-6912 to reach the Technical Support

Department.

Precautions

• Do not stand in the basin of the pedicure spa!

• Excessive water temperature is dangerous and should be checked before use. Optimum operating water temperature should not exceed 105

° exceed 120° F (49° C).

F (41

°

C) and the maximum supply water temperature should not

• In the Commonwealth of Massachusetts; water temperature is not to exceed 130

°

F (54

• Never bring or operate any electrical devices into or near the pedicure spa.

°

C) max.

• Always enter and exit the pedicure spa slowly and carefully, with basin in down position.

• This pedicure spa has a weight capacity of 350 pounds (158.8kg).

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Doc ID: 12080006 Rev: A Page 6 Technical Support: 800-626-6912 Date: 2/19/10

Thank you for selecting E UROPEAN T OUCH , the leading designer, manufacturer, and marketer of pedicure spas in North America. The 25th Anniversary Murano Spa (herein referred to as pedicure spa) is an innovative whirlpool pedicure spa that has been designed to serve you dependably for many years. Please take time to thoroughly read this entire manual before installation and use. If you have any problems or have questions regarding your pedicure spa, please contact E

UROPEAN

T

OUCH

’s Technical Support Department at 1-800-626-

6912, Monday through Friday 8 AM to 5 PM CST. After hours calls are recorded and attended to the next business day.

Important Safety Instructions

When using an electrical appliance, basic precautions should always be followed, including the following:

Read all instructions before using the Pedicure Spa.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1) Use the Pedicure Spa only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

2) Never operate the Pedicure Spa if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.

3) Never drop or insert any object into any opening.

4) Do not use outdoors.

5) Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

P

LEASE

, S

AVE

T

HIS

M

ANUAL

!

Doc ID: 12080006 Rev: A Page 7 Technical Support: 800-626-6912 Date: 2/19/10

Danger

Please Read Carefully.

1) Never use pins or other metallic fasteners with this appliance.

2) Carefully examine the covering before each use.

3) Discard the appliance if the covering shows any sign of deterioration, such as checking, blistering, or cracking.

4) Keep Dry – Do not operate in a wet or moist condition.

Warnings

1) WARNING: RISK OF ELECTRIC SHOCK; do not permit electric appliances (such as a hair dryer, lamp, telephone, radio, or television) within 1.5M of this hydro massage bathtub.

2) CAUTION: Test the ground fault circuit interrupter protecting this appliance periodically in accordance with the manufacturer’s instructions.

3) Temperatures sufficiently high to cause burns may occur regardless of the control setting. a. Do not use on…

• Infants

• Invalids

• Sleeping or unconscious person. b. Do not use on…

• Insensitive skin

• Person with poor blood circulation.

Note: Check the skin in contact with the heated area of the appliance frequently to reduce the risk of blistering.

4) Excessive water temperature is dangerous and should be checked before use. Maximum operating water temperature should not exceed 105

°

F (41

°

C) and the maximum supply water temperature should not exceed 120°F (49° C).

5) Always enter and exit the pedicure spa slowly and carefully.

6) Never bring or operate any electrical devices into or near the pedicure spa.

7) This pedicure spa has a weight capacity of 350 pounds.

8) Do Not Crush – Avoid sharp folds

9) Do not stand on or in appliance.

10) Use only while seated.

11) Keep children away from extended foot support

12) Connect this appliance to a properly grounded outlet only. See Grounding Instructions within the install manual.

Note: Always verify maximum temperatures with your local & state codes.

Doc ID: 12080006 Rev: A Page 8 Technical Support: 800-626-6912 Date: 2/19/10

Product Specifications

25th Anniversary Murano Spa Specifications

• Overall dimensions with seat back, glass basin raised and seat in full recline:

With out manicure trays 74"L (188cm) x 32"W (82cm) x 55”H Max (140cm)

With manicure trays 74”L (188cm) x 55”W (130cm) x 55”H Max (140cm)

• Empty Weight: 350lbs. (159kg)

• Shipping Weight: 400lbs (182 kg) Ships fully assembled except for the outer cover.

• Capacity of Tub: 5 U.S. Gallons

• Power Source: 120V AC/15Amp, 60HZ (dedicated circuit, GFCI Protected)

• Construction: Glass Reinforced Polyester (GRP) frame covers, steel frame

• Glass Basin: Borosilicate glass; Impact resistant, thermal shock resistant, scratch resistant, chemical and stain resistant.

• Glass Basin Dimensions: 25.5" L X 24.5"W X 9"H.

• Clean Touch Pipe-Free System: No closed loop circulating pipes, 100% fully drained and cleanable.

• Regulatory compliance: Electrical: UL 1951,

Plumbing: ASME 112.18.3

EMC: EN55041-1:2006 & EN55014-2: 1997

Important Requirements

European Touch requires that you contact a local, licensed plumber and licensed electrician to install your new pedicure spa. Installation must be in compliance with all your local and state building codes. Your pedicure spa cannot operate efficiently or safely unless it is provided with adequate electrical power, sufficient water pressure, proper water temperature, and required drainage capabilities. Contact your local building inspector for information regarding local code compliance procedures that need to be followed when having these spas installed. Subsequent inspections and approvals that may be required are the responsibility of the purchaser.

(See limited warranty regarding incidental or consequential exclusions – page 2).

Plumbing & Certifications

• Hot & Cold water supply lines required. The 25th Anniversary Murano Spa “tail” contains the hot & cold water supply hoses and the drain hose. The hoses are ½” ID hoses that are 6" long from the back of the 25th

Anniversary Murano Spa. The connection is ½” female hose fitting. The maximum supply water temperature must not exceed 120° F (49° C). See Commonwealth of Massachusetts for local specifics below.

• Compliant with IAPMO plumbing standards.

• Compliant with ASME standards A112.18.3 for backflow protection and A112.9 for water retention.

• The 25th Anniversary Murano Spa has been designed with the latest technology plumbing components, which are approved to ASSE, and IAPMO standards.

Commonwealth of Massachusetts Plumbing & Certifications

• All plumbing must be installed by a plumber licensed by the commonwealth of Massachusetts.

• All plumbing products shall be in compliance with the Commonwealth of Massachusetts State Fuel & Gas plumbing codes CMR 248; 1.00-7.00 as amended.

• All plumbing installations shall include back flow protection devices in compliance with CMR 248,

Massachusetts State Plumbing Code. o Water temperature not to exceed 130°F (54°C) max.

NOTE

NOTE

1

2

: All specifications are subject to change without notice.

: All dimensions are approximate.

Doc ID: 12080006 Rev: A Page 9 Technical Support: 800-626-6912 Date: 2/19/10

Doc ID: 12080006 Rev: A Page 10 Technical Support: 800-626-6912 Date: 2/19/10

Installation Instructions

The 25th Anniversary Murano Spa installation must comply with all plumbing and electrical codes. A licensed plumber and licensed electrician must complete the applicable connections of the pedicure spa.

Electrical Service

110V: 110V, 60 Hz, 5.0 Amp GFCI protected grounded circuit must be used to supply power to the pedicure spa. (220V if ordered in 220V configuration)

220V: 220V, 50/60 Hz, 5.0 Amp GFCI protected grounded circuit must be used to supply power to the pedicure spa.

Water Supply

• All plumbing connections must conform to local codes.

• Water pressure must be 30 to 80 PSI for the sprayer to operate correctly.

• Maximum operating water temperature should not exceed 105 °

F (41

°

C) and the maximum supply water temperature should not exceed 120° F (49° C). (In Massachusetts, the maximum supply water temperature should not exceed 130

°

F (54

°

C)). Adjust the hot water heater accordingly.

• For hot and cold water supply fittings and power drain fittings location, see figure 1 below.

• Carefully connect the incoming water supply lines to the appropriate fittings located on the back of the pedicure spa. Shut-off valves are recommended.

Drain Facilities

The 25th Anniversary Murano Spa comes equipped with a power drain pump. The discharge hose is located at the back of the 25th Anniversary Murano Spa. The drain hook-up must meet local plumbing codes.

Location/Positioning

Check your Local & State plumbing codes for additional backflow requirements. Any additional requirements are the responsibility of the owner of the unit.

Backflow Protection Devices for Faucets with Side Spray: Check valves comply with ANSI/ASME

A112.18.3M, A112.18.1M, and CSA B12.

Doc ID: 12080006 Rev: A Page 11 Technical Support: 800-626-6912 Date: 2/19/10

Features of the 25th Anniversary Murano Spa

Basin Material

The basin has been designed to enhance the beauty of your salon. The smooth textured finish is durable, bacteria resistant, and easy to clean. The basin is designed for easy cleaning using the sprayer and an EPA approved disinfecting cleaner. Please read the recommendations on the cleaning product before using it in the spa to make sure that it is safe on glass products. Call European Touch Technical Support at 800-626-6912 with any questions regarding the cleaning of your Spa.

Cushioned Leg Supports

The cushions are contoured for added comfort. The leg supports are designed for easy cleaning using an EPA approved disinfecting cleaner.

Technician Operation Guide

Filling Spa

a. Lift the faucet handle located on the front of the spa. b. Adjust water temperature by moving the handle left for cold and right for hot water. c. Fill the spa to the height of the client’s ankles. Caution there is no overflow protection.

Water movement on/off

a. To start the water movement, press the “On/Off” button located on the front panel of the spa.

Note: Clean Touch cover must be in place for the water movement to operate.

Basin Up and Basin Down

a. “Arrow Up symbol” ▲ controls the upward travel of the glass basin. The basin will move only when the button is pressed or until the maximum height is reached. b. “Arrow Down symbol” ▼ controls the downward travel of the glass basin. The basin movement will automatically stop once it reaches the full down position.

Drain Water

a. To drain the water from the 25th Anniversary Murano Spa, turn the drain handle located on the right side of the front panel. b. Press the drain portion of the button on the front panel.

Note: Drain will time out and automatically shut off in approximately 3.5 minutes.

Doc ID: 12080006 Rev: A Page 12 Technical Support: 800-626-6912 Date: 2/19/10

Air Caress Relaxation & Remote Control for 25

th

Anniversary Murano

Remote Control Features

Turning On/Off

1. Press “Power” button to turn on

2. Repeat step 1 to turn off

Inflate/Deflate Air Pillows for a Customized Massage

1. Press “Select” button

2. Choose any combination of Zones (1 – 3) by pressing corresponding button(s).

3. INFLATE or DEFLATE air pillows as desired by pressing and holding corresponding button.

Select Massage Type

1. Target three areas of the back by pressing any one, or a combination of, Zones (1 – 3). Zone 1 – Upper portion, Zone 2 – Middle Portion, Zone 3 – Lower Portion.

2. Choose between PULSE or WAVE by pressing corresponding button. PULSE cycles through the Zones and length of time spent on each zone is adjusted by pressing the “Cycle” button.

P OWER

Turns Air Caress

Relaxation Massage

System On and Off

C YCLE

While in PULSE, select the length of time (short, medium, long) to cycle through Zones 1 - 3

R

ECLINE

S

EAT

B

ACK

Client tilts seat forward or back according to preference

Doc ID: 12080006 Rev: A Page 13 Technical Support: 800-626-6912 Date: 2/19/10

Air Relaxation System

Turning On\Off

1. Press POWER button to turn ON.

2. Repeat Step #1 to turn OFF.

Inflate\Deflate Pillows for a Customized Massage

1. Press SELECT button.

2. Choose any combination of ZONES 1-3 by pressing button(s).

3. INFLATE\DEFLATE massage pillow(s) by pressing and holding corresponding button.

Selecting Massage Type

1. First, choose area of back (lower, middle, upper) desiring massage by pressing any one, or combination of, ZONES 1-3.

2. Choose between PULSE or WAVE by pressing button.

Selecting Massage Mode Cycle Time

1. Choose between SHORT, MEDIUM or LONG cycles by pressing CYCLE button.

“CYCLE”

“POWER”

Turns air relaxation system on and off

“MODE” / “SELECT”

Selecting of the zones

“ZONE” / “1”

Upper Zone

“MODE” / “PULSE”

Pulse massage

“ZONE” / “2”

Middle Zone

“MODE” / “WAVE”

Wave massage

“INFLATE”

Raise the air; inflate, in the cushions

Choose short, medium, or long time cycles

“ZONE” / “3”

Lower Zone

“DEFLATE”

Lower the air; deflate, in the cushions

Doc ID: 12080006

*Note: The Air Relaxation System is pre-programmed to run for 15 minutes and cannot be adjusted. To turn the system back on after it turns off, press the

“Power” button and select the desired operating mode.

Rev: A Page 14 Technical Support: 800-626-6912 Date: 2/19/10

Roller Massage & Remote Control for 25th Anniversary Murano

Remote Control Features

Turning On/Off

1. Press “Power” button to turn on

2. Repeat step 1 to turn off

Select Massage Type

1. Target three areas of the back by pressing any one, or a combination of, Zones (1 – 3). Zone 1 – Upper portion,

Zone 2 – Middle Portion, Zone 3 – Lower Portion.

2. Choose between PULSE or WAVE by pressing corresponding button. PULSE cycles through the Zones and length of time spent on each zone is adjusted by pressing the “Cycle” button.

P OWER

Turns massage controller on and off

R OLLER

Starts roller massage system in seat back.

V IBRATION

Turns vibration on in the seat along with different program selections.

R ECLINE S EAT B ACK

Client tilts seat forward or back according to preference

S LIDE

Moves the entire chair in the horizontal plane only.

Doc ID: 12080006 Rev: A Page 15 Technical Support: 800-626-6912 Date: 2/19/10

Roller / Vibration Massage System

Turning On\Off

1. Press POWER button to turn ON.

2. Repeat Step #1 to turn OFF.

Initiate roller massage in seat back

1. Press the membrane switch under “ROLLER”.

2. Massage will automatically turn off in 20 minutes.

Initiate seat vibration massage.

1. Select vibration zone Waist, Thighs or both.

2. Choose appropriate strength, speed vibration, along with function

A = Wave

B = Pulse

C = Continuous

Selecting Massage Mode Cycle Time

1. Massage system is preprogrammed for 20 minutes.

“Roller”

Turns rolling mechanism on

“Power Button”

Turns massage system on

“Seat Vibration”

Waist

“Seat Vibration”

Thighs

“Vibration Strength”

High, Medium, Low

“Vibration Speed”

High, Medium, Low

“Vibration Function”

A = Wave

B = Pulse

C = Continuous

Doc ID: 12080006 Rev: A Page 16 Technical Support: 800-626-6912 Date: 2/19/10

Removing the Clean Touch Assembly from the Basin Floor

Removing the Clean

Touch

Assembly from the

Basin

Floor

To remove the Clean Touch

Assembly, move the longer nose in the direction as shown.

Separate the clean touch inlet cover from the base twisting counter-clockwise.

Remove the impeller by lifting from the basin.

Pedicure Product Guidelines

Because there are so many different products on the market, it is difficult to list all of the pedicure products that are safe to use in our pedicure spas. However, the following guidelines can be used:

• It is your responsibility to understand and follow your state’s regulations regarding product cleaning and disinfecting requirements.

• Do not use any products containing a foaming agent; this will cause excessive foam.

• It has been determined that products containing non-dissolving abrasives (such as sand and sea salts) will not harm the internal component structure of your pedicure spa as long as the entire EUROPEAN TOUCH cleaning requirements are followed without deviation.

• Oil based products may be used in your pedicure spa as long as the cleaning requirements are met.

• Please use pedicure products and cleaning solutions in accordance with each manufacturer's directions.

• It is your responsibility to understand and follow your state’s regulations regarding product cleaning and disinfecting requirements.

EUROPEAN TOUCH pedicure spas will give you many years of service as long as proper precautions, precise cleaning, and operating instructions are followed. It is the responsibility of the pedicure spa user to properly clean and maintain the pedicure spa.

Doc ID: 12080006 Rev: A Page 17 Technical Support: 800-626-6912 Date: 2/19/10

Cleaning and Disinfecting Pedicure Equipment

These are recommended procedures for cleaning and disinfecting all types of pedicure equipment, including whirlpool units, air-jetted basins, pipe-less and all non-whirlpool basins, sinks, bowls and tubs. In all cases described below, we recommend using an EPA registered hospital liquid disinfectant that the label claims is a bactericide, virucide and fungicide. Always record the time each cleaning procedure is performed in a salon pedicure cleaning log, for your convenience, a sample Cleaning and Disinfecting log sheet is located on page

18. A patron or state board representative may request to see your pedicure spa cleaning log.

“Pipe-less” foot spas - For units with footplates, impellers, impeller assemblies and propellers

After every client

1. Drain all water from the basin.

2. Remove impeller, footplate and any other removable components according to the manufacturer’s instructions.

3. Thoroughly scrub impeller, footplate and/or other components and the areas behind each with a liquid soap and a clean, disinfected brush to remove all visible residue, then reinsert impeller, footplate and/or other components.

4. Refill the basin with water and circulate the correct amount (read the label for mixing instructions) of the EPA registered hospital disinfectant through the basin for ten minutes.

5. Drain, rinse and wipe dry with a clean paper towel.

At the end of every day

1. Fill the basin with warm water and chelating detergent (cleansers designed for use in hard water) and circulate the chelating detergent through the spa system for five to ten minutes (follow manufacturer’s instructions). If excessive foaming occurs, discontinue circulation and let soak for the remainder of the ten minutes.

2. Drain the soapy solution and rinse the basin.

3. Refill the basin with clean water and circulate the correct amount (read the label for mixing instructions) of the EPA registered hospital disinfectant through the basin for ten minutes.

4. Drain, rinse and wipe dry with a clean paper towel.

At least once each week

1. Do not drain the disinfectant solution - Turn off the unit and leave the disinfecting solution in the unit overnight.

2. In the morning drain, rinse and wipe dry with a clean paper towel.

Doc ID: 12080006 Rev: A Page 18 Technical Support: 800-626-6912 Date: 2/19/10

Additional Information about Disinfectants and Detergent Cleaners

A. EPA registered liquid disinfectants used in the salon: i. Must have the words ‘bactericidal, fungicidal and virucidal’ and ‘hospital’ on the label. ii. Must be mixed, used, stored and disposed of according to manufacturer’s label instructions.

*It is against Federal Law to use an EPA registered disinfectant contrary to its label. iii. Must be prepared fresh every day and replaced immediately when the solution becomes visibly contaminated. iv. Are ineffective when proper cleaning is not performed before use. v. Requires complete immersion in the correct amount of disinfectant for ten minutes after cleaning of all visible residue. Complete immersion means enough liquid to cover all surfaces of the item. Note: if the disinfectant manufacturer’s label requires a different immersion time for soaking, you should always follow the label’s instructions. vi. Spray disinfectants are for cleaning surfaces only and are not adequate for disinfecting tools and pedicure equipment in the salon.

B. EPA Registered hospital “one-step” cleaner/ disinfectants may be used for disinfecting pedicure equipment if: i. They are EPA registered, hospital, bactericidal, fungicidal and virucidal and have the words ‘one-step’ on the label. ii. Tools and equipment are first cleaned of large amounts of residue. iii. Are used exactly as described by the manufacturer’s instructions.

C. All bottles and containers (other than the original manufacturers’ container) containing any disinfectant must be properly labeled listing the contents, percentage solution (concentration) and date of mixing.

D. Surfactant chelating detergents break down residue from pedicure products and are effective in hard water.

Hard water contains calcium and magnesium ions, which can inactivate disinfectants and create residue films that are difficult for ordinary detergents to remove.

E. All brushes used to remove visible debris from the foot spa, tub or basin must be properly cleaned and disinfected between each use.

F. You must record the time of each cleaning procedure in the salon pedicure cleaning log. Keep a log available to show clients. It demonstrates that you regularly clean and disinfect your pedicure equipment, to ensure the customer is protected.

G. Read and follow the instructions provided with the pedicure equipment to ensure proper use.

Doc ID: 12080006 Rev: A Page 19 Technical Support: 800-626-6912 Date: 2/19/10

Seat Assembly

Exploded Part Views

Right Side Manicure Tray Assembly

Doc ID: 12080006 Rev: A Page 20 Technical Support: 800-626-6912 Date: 2/19/10

Left Side Manicure Tray Assembly

Seat Track Assembly

Doc ID: 12080006 Rev: A Page 21 Technical Support: 800-626-6912 Date: 2/19/10

Basin Assembly

Front Plate – Foot Rest Assembly

Doc ID: 12080006 Rev: A Page 22 Technical Support: 800-626-6912 Date: 2/19/10

Belly Pan Assembly

Power Drain Pump (PDP) Assembly

Doc ID: 12080006 Rev: A Page 23 Technical Support: 800-626-6912 Date: 2/19/10

Trouble Shooting Guide

Problem Resolution

No Water

Movement

Water Not

Draining

Basin is not rising

/ lowering

Chair tilt and slide not working

Chair Massage is not working

Basin Losing

Water

Water not working or pressure is low

Breaker / Fuse

• Verify unit is plugged in to live wall outlet.

• Verify motor is plugged into black control box.

• Verify cable between button and jets control box is plugged in.

• Verify the wires to the button are not damaged.

• Verify the impeller is in place (remove clean touch assembly).

• Verify clean touch assembly is properly attached to the basin.

• Verify black sensor underneath the basin is plugged in.

• Verify pop-it / plunger is opening (or opening enough)

• Verify unit is plugged in to live wall outlet.

• Verify that the power plug is connected to the PDP control box.

• Verify cable between button and PDP control box is plugged in.

• Verify unit is plugged in to a live wall outlet.

• Verify cable from button to actuator control box is plugged in.

• Verify basin lift actuator is plugged into the actuator control box.

• Verify control box is plugged into the power strip on the spa.

• Verify unit is plugged in to a live wall outlet.

• Verify remote control is plugged into the actuator control box.

• Verify actuators are plugged into the actuator control box.

• Verify control box is plugged into the power strip on the spa.

• Verify remote control is plugged in.

• Verify wires are connected on the back or inside the back of the chair.

• Inspect drain plunger for tears in rubber gasket.

• Verify drain plunger height is correct.

• Verify drain strainer is inserted properly over the hex bolt.

• Verify bolt below plunger is tight (do not over tighten).

• Multiple spas or other salon equipment on at the same time may reduce water temperature or pressure.

• Verify external water supply valves are on.

• Unscrew the sprayer head from its hose and verify screen is clear.

Contact service department at European Touch

CONTACT EUROPEAN TOUCH TECHNICAL SUPPORT AT 1-800-626-6912 WITH ANY

ISSUES THAT CANNOT BE RESOLVED USING THIS TROUBLESHOOTING GUIDE.

Doc ID: 12080006 Rev: A Page 24 Technical Support: 800-626-6912 Date: 2/19/10

European Touch

8301 W Parkland Court

Milwaukee, WI 53223

1-800-626-6912

Fax: 1-414-357-6360 [email protected] [email protected] www.europeantouch.com