Maytag MEW6630DDS - 30 Inch Electric Double Wall Oven User`s guide

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
ELECTRIC CONVECTION WALL OVEN
TABLE OF CONTENTS
○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Welcome ................................................................. 1
Safety Instructions ............................................... 2-3
Controls at a Glance ............................................ 4-6
Function Pads ................................................ 4-5
Setting the Clock .............................................. 5
Setting the Timers ............................................ 5
Oven Light ....................................................... 5○
Oven Control Lockout ..................................... 6
Oven Operation ................................................. 7-11
Baking, Roasting and Convection Cooking ..... 7
Oven Vent and Oven Fans ................................ 7
Oven Racks and Positions ................................ 8
Broiling ............................................................ 9
Clock Controlled Oven Operations ........... 10-11
Care and Cleaning ........................................... 12-15
Self-Clean Oven ........................................ 12-13
Cleaning Chart .......................................... 14-15
Maintenance ......................................................... 15
Before You Call for Service ............................. 16-17
If You Need Service .............................................. 18
Warranty ............................................................... 19
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
®
Models: MEW6627 • MEW6630
Welcome
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
IMPORTANT: Keep this guide and the sales receipt in
a safe place for future reference. Proof of original
purchase date is needed for warranty service.
Congratulations on your choice of a Maytag double electric
wall oven. Your complete satisfaction is very important to us.
Read this user’s guide carefully. It is intended to help you
operate and maintain your new wall oven.
If you have questions, write us (include your model
number and phone number) or call:
Maytag Appliances Sales Company
Attn: CAIR® Center
P.O. Box 2370
Cleveland, TN 37320-2370
1-800-688-9900 (USA)
1-800-688-2002 (CANADA)
1-800-688-2080 ( U.S. TTY for deaf, hearing
impaired or speech impaired)
(Mon. - Fri., 8 am-8 pm Eastern Time)
Internet: http://www.maytag.com
In addition, you will find a booklet entitled “Cooking Made
Simple.” It contains information on selecting bakeware and
provides baking, roasting and broiling tips.
Save time and money. Check the “Before You Call” section
of this guide. It lists causes of minor operating problems that
you can correct yourself.
However, should you need service, it is helpful to have the
model and serial numbers available. This information can be
found on the data plate located on the oven front frame.
These numbers are also on the Product Registration card that
came with your appliance. Before sending in this card, record
these numbers along with the purchase date below.
For service information, see page 18.
Note:
Model Number
• In our continuing effort to improve the quality
and performance of our cooking products, it may
be necessary to make changes to the appliance
without revising this guide.
–– –– –– –– –– –– –– –– –– ––
Serial Number
–– –– –– –– –– –– –– –– –– ––
Date of Purchase
_______________________________
1
IMPORTANT SAFETY INSTRUCTIONS
The following instructions are based on safety considerations
and must be strictly followed to eliminate the potential risks
of fire, electric shock, or personal injury.
Installation and Repair
•
Have your appliance installed and properly grounded by
a qualified installer according to the installation instructions.
•
To ensure proper operation and avoid possible injury or
damage to unit do not attempt to adjust repair, service, or
replace any part of your appliance unless it is specifically
recommended in this book. All of the servicing should be
referred to a qualified installer or servicer.
To Prevent Fire or Smoke Damage
•
Be sure all packing materials are removed from the appliance before operating it.
•
Keep area around appliance clear and free from combustible materials. Flammable materials should not be stored
in an oven.
•
Many plastics are vulnerable to heat. Keep plastics away
from parts of the appliance that may become warm or
hot.
•
To prevent grease fires, do not let cooking grease or other
flammable materials accumulate in or near the appliance.
•
Do not use the oven as a storage area for food or cooking
utensils.
•
Many aerosol-type spray cans are EXPLOSIVE when
exposed to heat and may be flammable. Avoid their use
or storage near the oven.
In Case of Fire
•
Use dry chemical or foam-type extinguisher or baking
soda to smother fire or flame. Never use water on a grease
fire.
1. Turn off appliance to avoid spreading the flame.
•
Children must be taught that the appliance and utensils
in it can be hot. Let hot utensils cool in a safe place, out
of reach of small children. Children should be taught
that an appliance is not a toy. Children should not be
allowed to play with controls or other parts of the unit.
•
CAUTION: NEVER store items of interest to children
in cabinets above an appliance. Children climbing on
the appliance or on the appliance door to reach items
could be seriously injured.
About Your Appliance
•
To prevent potential hazard to the
user and damage to the appliance, do
not use appliance to heat or warm a
room.
•
Do not obstruct the flow of air by
blocking the oven vent.
•
DO NOT TOUCH HEATING ELEMENTS OR INTERIOR SURFACES OF OVEN. Heating elements may
be hot even though they are dark in color. Interior surfaces of any oven become hot enough to cause burns.
During and after use, do not touch, or let clothing or
other flammable materials contact heating elements or
interior surfaces of oven until they have had sufficient
time to cool. Other surfaces of the appliance may become hot enough to cause burns – among these surfaces are: oven vent openings and surfaces near these
openings, oven doors, windows of oven doors.
•
CAUTION: NEVER use an appliance as a step to reach
cabinets above. Misuse of appliance doors, such as stepping, leaning or sitting on the door, may result in possible tipping of the appliance, breakage of door, and
serious injuries.
•
Do not touch a hot oven light bulb with a damp cloth as
the bulb could break. Should the bulb break, disconnect power to the appliance before removing bulb to
avoid electrical shock.
•
A fan should be heard during some bake, convect bake,
and all broil and cleaning operations. If you do not hear
the fan, call an authorized servicer.
•
NEVER use aluminum foil to cover an oven rack or
oven bottom. Misuse could result in risk of electric
shock, fire, or damage to the appliance. Use foil only as
directed in this guide. Do not allow aluminum foil to
contact heating element.
2. NEVER pick up or move a flaming pan.
3. Smother fire or flame by closing the oven door.
Child Safety
•
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
NEVER leave children alone or unsupervised near the
appliance when it is in use or is still hot. Children should
never be allowed to sit or stand on any part of the appliance as they could be injured or burned.
2
IMPORTANT SAFETY INSTRUCTIONS (continued)
○ ○ ○
Cooking Safety
Cleaning Safety
•
NEVER heat an unopened food container in the oven. Pressure build-up may cause container to burst resulting in serious personal injury or damage to the appliance.
•
•
Use dry, sturdy potholders. Damp potholders may cause
burns from steam. Dish towels or other substitutes should
never be used as potholders because they can trail across
hot elements and ignite or get caught on appliance parts.
Turn off all controls and wait for appliance parts to cool
before touching or cleaning. Clean with caution. Use
care to avoid steam burns if a wet sponge or cloth is
used to wipe spills on a hot surface. Some cleaners can
produce noxious fumes if applied to a hot surface.
•
Clean only parts listed in this guide.
•
•
NEVER wear loose fitting or long hanging-sleeved apparel
while cooking. Clothing may ignite and cause burns if garment comes in contact with heating elements.
Self-Clean Oven
•
Do not clean door gasket. The door gasket is essential
for a good seal. Care should be taken not to rub, damage, or move the gasket.
Always place oven racks in the desired
positions while oven is cool. If a rack
must be moved while hot, use a dry
potholder. Do not let potholder contact
hot element in oven.
•
Do not use oven cleaners or oven liners of any kind in
or around any part of the self-clean oven.
•
Before self-cleaning the oven, remove broiler pan, oven
racks and other utensils, and wipe off excessive
spillovers to prevent excessive smoke or flare ups.
•
CAUTION: NEVER leave food or cooking utensils,
etc. in the oven during the self-clean cycle.
•
Use care when opening the oven door. Let hot air or steam
escape before removing or replacing food.
•
PREPARED FOOD WARNING: Follow food manufacturer’s instructions. If a plastic frozen food container and/
or its cover distorts, warps, or is otherwise damaged during
cooking, immediately discard the food and its container.
The food could be contaminated.
•
Important Safety Notice
and Warning
The California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65) requires the Governor
of California to publish a list of substances known to the
State of California to cause cancer or reproductive harm,
and requires businesses to warn customers of potential exposures to such substances.
Always turn off all controls when cooking is completed.
Utensil Safety
•
Follow the manufacturer’s directions when using oven cooking bags.
•
This appliance has been tested for safe performance using
conventional cookware. Do not use any devices or accessories that are not specifically recommended in this manual.
Do not use add-on oven convection systems. The use of
devices or accessories that are not expressly recommended
in this guide can create serious safety hazards, result in performance problems, and reduce the life of the components
of the appliance.
•
Users of this appliance are hereby warned that when the
oven is engaged in the self-clean cycle, there may be some
low-level exposure to some of the listed substances, including carbon monoxide. Exposure to these substances
can be minimized by properly venting the oven to the outdoors by opening the windows and/or door in the room
where the appliance is located during the self-clean cycle.
IMPORTANT NOTICE REGARDING PET BIRDS:
Never keep pet birds in the kitchen or in rooms where the
fumes from the kitchen could reach. Birds have a very sensitive respiratory system. Fumes released during an oven
self-cleaning cycle may be harmful or fatal to birds. Fumes
released due to overheated cooking oil, fat, margarine and
overheated non-stick cookware may be equally harmful.
Only certain types of glass, glass/ceramic, ceramic, earthenware, or other glazed utensils are suitable for oven service without breaking due to the sudden change in temperature. Follow utensil manufacturer’s instructions when
using glass.
Save These Instructions for Future Reference
3
Controls at a Glance
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
The control panel is designed for ease in programming. The display window shows time of day, timer and oven functions.
Indicator words flash to prompt your programming steps. “U” indicates upper oven is ON and “L” indicates lower oven is
ON.
UPPER OVEN
CANCEL
BAKE
BROIL
1
2
3
4
5
6
7
8
9
CLEAN
CONVECT
LOWER OVEN
CANCEL
BAKE
BROIL
CLEAN
TIMER ONE
TIMER TWO
CLOCK
COOK TIME
STOP TIME
0
Function Pads
•
•
Press the desired pad.
BROIL Pad
Touch the appropriate number pad(s) to enter time or
temperature.
Use for top browning and broiling.
•
A beep will sound when any pad is touched.
1. Press BROIL pad.
2. The first number pad pressed will enter “HI” broil.
Press the appropriate number pads to set an alternative broil temperature.
NOTE: Five seconds after entering the number, the time or
temperature will automatically be entered. If more than five
seconds elapse between touching a function pad and the
number pads, the function will be cancelled and the display
will return to the previous display.
See page 9 for additional information.
CLEAN Pad
Use to set self-clean cycle.
Number Pads
Use to set time or temperature.
1. Press CLEAN pad.
2. Press any number pad for “3:00” hours of cleaning, 2,
0, 0 for “2:00” hours or 4, 0, 0 for “4:00” hours.
CANCEL Pad
See pages 12-13 for additional information.
Use to cancel all programming except Clock and Timer
functions.
CONVECT Pad
BAKE Pad
Use for convection baking.
Use for conventional baking or roasting.
1. Press CONVECT pad. Press the appropriate number
pads for desired temperature.
1. Press BAKE pad.
2. Press the appropriate number pads for desired
temperature.
See page 7 for additional information.
See page 7 for additional information.
4
Controls at a Glance
(continued)
COOK TIME/STOP TIME Pads
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Example: To set Timer Two for 1 hour and 30 minutes,
press the TIMER TWO pad and the numbers 1,3,0
pads. After five seconds the display will show:
Use to program the oven to start and stop automatically.
1. Press BAKE or CONVECT pad. Press the appropriate
number pads for desired temperature.
2. Press COOK TIME pad. Press the appropriate number
pads to enter cooking time in hours and minutes.
NOTE: If both timers are set, the timer with the least
amount of time remaining will have display precedence.
3. To delay the start of cooking, press STOP TIME pad.
Press the appropriate number pads to enter the time you
want the oven to stop.
3. The timer will chime once when there is one minute
remaining. The final minute will count down in seconds.
See page 10-11 for additional information.
Setting the CLOCK
4. At the end of the time set, the timer will chime four times
and “End” will appear in the display. If the timer is not
cancelled (see “To cancel” below), “End” will remain
in the display and there will be two chimes every 30
seconds for five minutes.
1. Press CLOCK pad.
• The indicator word TIME will flash in the display.
2. Press the appropriate number pads until the correct time of
day appears in the display.
When electrical power is supplied or after a power interruption, the last clock time, before power was interrupted, will
flash.
To cancel:
1. Press and hold the appropriate TIMER pad. After a
slight delay the time of day will reappear.
To recall the time of day when another time function is
showing, press the CLOCK pad.
OR
2. Press the appropriate TIMER pad and the “0” number
pad. After a slight delay the time of day will reappear.
Clock time cannot be changed when the oven has been
programmed for clock controlled oven operations or selfclean.
Notes. . .
• Pressing CANCEL pad to cancel the timer will cancel
Setting the TIMER ONE/TWO
ALL selected oven functions except the timer.
Use to set and then signal the completion of a time period up
to 12 hours (12:00).
• If
you would like to eliminate all the “reminder”
chimes, press and hold the CANCEL pad for 12
seconds until a beep sounds. (This will not eliminate
the initial four chimes.) To restore the reminder chimes,
press and hold the CANCEL pad for 12 seconds.
The timers can be used independently of any other oven
activity and can be set while another oven function is operating. The timers do not control the oven.
1. Press the TIMER ONE or TIMER TWO pad.
• The indicator word TIMER will flash along with # 1 or
#2 plus “0HR:00” appears in the display.
OVEN LIGHT Pad
2. Press the appropriate number pads until the desired number of minutes or hours and minutes appear in the display.
The oven light automatically comes on whenever the oven
door is opened. When the door is closed, press the OVEN
LIGHT pad to turn the oven light on or off. A beep will
sound every time the OVEN LIGHT pad is touched.
Example: To set Timer One for 5 minutes, press the
TIMER ONE pad and the number 5 pad. After five
seconds, the display will show:
5
Control Options
Oven Control Lockout
To adjust the thermostat:
The oven operation controls - Bake, Convect, Broil, and Clean
- can be locked in the “OFF” position. The Timer and Clock
controls can always be used regardless of the lockout.
1. Press the BAKE pad.
2. Enter 500° by pressing the number pads “5, 0, 0”.
3. Press and hold the BAKE pad for several seconds
until 00° appears in the display.
If an oven function is currently being used, the controls cannot
be locked off.
•
If the oven temperature was previously adjusted,
the
change will be displayed. For example, if the oven temperature was reduced by 15°, the display will show 15°.
To Set Controls
1. Press and hold the COOK TIME pad and the STOP TIME
pad at the same time for several seconds.
• The indicator word “OFF” will appear and remain in
4. Press the appropriate number pads to select the temperature change desired.
the display for 15 seconds.
• If an oven function pad is pressed while controls are
locked off, the indicator word “OFF” will reappear
in the display for 15 seconds.
To cancel: Press and hold the COOK TIME pad and the
STOP TIME pad at the same time for several seconds. The
indicator word “OFF” will appear briefly and then disappear.
•
The oven temperature can be increased up to
35° (+35°) or reduced by as much as 35° (-35°)
in 5° increments.
•
Pressing the BROIL pad will change the - sign
to a positive number or back to a negative number.
5. When you have made the adjustment, press the
CANCEL pad and the time of day will reappear in the
display. The oven will now bake at the adjusted
temperature.
Adjusting Oven Temperature
If you think the oven should be hotter or cooler, you can adjust
it yourself. To decide how much to change the thermostat, set
the oven temperature 25°F higher or lower than the temperature
in your recipe, then bake. The results of the “test” should give
you an idea of how much to adjust the thermostat.
It is not necessary to readjust the oven temperature if
there is a power interruption. This adjustment will not
affect broil or clean temperatures.
NOTE: Do not change the temperature setting more than
10° at a time before testing the oven.
6
Oven Operation
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Baking, Roasting and
Convection Cooking
• When the oven is preheated, the oven will chime and
Every oven has its own characteristics. You may find that the
cooking times and temperatures vary slightly from your old
oven. This is normal.
the ON and PREHEAT indicator words will go off.
Allow 7-11 minutes for the oven to preheat.
4. At the end of cooking, turn the oven off by pressing the
CANCEL pad. Remove food from oven. The oven
will continue operating until the CANCEL pad is
pressed.
Oven Vent
When the oven is in use, the area near the oven vent may feel
warm to the touch. Do not block the vent opening for best
baking results.
Notes . . .
The oven vent is located below the control panel on your wall
oven.
• If more than five seconds elapse between pressing a pad and pressing a number pad, the display
will return to the previous display.
Oven Fans
A cooling fan will automatically turn on during cleaning,
broiling and some baking operations. It is used to help keep
internal parts on the control panel cool. The fan will automatically turn off when parts have cooled. The fan may continue to
operate after the oven has been turned off. This is normal.
• Whenever the ON indicator word appears in the
display, the oven is heating.
• To recall the set temperature during preheat,
press the appropriate BAKE or CONVECT pad.
The set temperature will be displayed briefly and
then return to the on-going program.
A convection fan is used to circulate hot air in the oven when the
convection feature is selected. It automatically turns on whenever the CONVECT pad is pressed and will turn off when
CONVECT is canceled.
• To change the oven temperature during cooking,
press the appropriate BAKE or CONVECT pad
and the appropriate number pads for the desired
oven temperature. If you are lowering the temperature below the current oven temperature, the
indicator words PREHEAT and ON will appear
briefly and the preheat chime will sound.
NOTE: The convection fan will automatically stop whenever
the oven door is opened.
Setting the Controls for Baking,
Roasting and Convection Baking
• As a general rule when convection baking, set
the oven temperature 25°F lower than the conventional recipe or prepared mix directions.
Times will be similar to a few minutes less than
directions.
1. Place oven racks on proper rack positions (see page 8).
2. Press BAKE or CONVECT pad.
• The indicator words BAKE or CONV BAKE will flash
and three dashes will appear.
• When convection is used to roast meats, roasting
times are generally 25-30% less. (Maintain conventional roasting temperature.)
3. Press the appropriate number pads for the desired oven
temperature.
• The temperature can be set from 100° to 550° F in
• For additional baking, roasting and convection
cooking tips plus a roasting chart with recommended roasting temperatures and times, see
“Cooking Made Simple” booklet.
5° increments.
• After five seconds the oven will begin to preheat.
The
indicator words ON and PREHEAT will appear in the
display and 100° or the actual oven temperature, whichever is higher.
• The temperature in the display will increase in 5°
increments until the oven reaches the preset
temperature.
7
Oven Racks
Double Oven - two flat racks and one offset rack plus an
additional offset and flat rack for the lower oven are packaged
in your oven.
Rack Position #2:
Roasting small cuts of meat, cakes in tube or bundt
pans, casseroles.
To remove: Pull forward to
the “stop” position; lift up on
the front of the rack and pull
out.
Rack Position #2o (offset on #2):
Roasting, loaves of bread, angel food cake.
Rack Position #1:
Large cuts of meat and turkey, custard pie,
dessert souffle.
To replace: Place rack on
the rack support in the oven;
tilt the front end up slightly;
slide rack back until it clears
the lock-stop position; lower
front and slide into the oven.
Multiple Rack Cooking:
Two racks (Convection or conventional cooking):
Cookies use #1 and #4o. Cakes use #2 and #4o.
Three racks (convection cooking only):
Use #1, #3o, #4. (See illustration at left.)
Rack Positions
Notes . . .
Three rack convection cooking.
Rack Position #4o (offset rack on #4):
Most broiling.
Rack Position #3:
Some baked goods.
Rack Position #3o (offset rack on #3):
Most baked goods, pies, cakes and cookies.
8
•
The use of the offset rack is denoted in the list above
as an “o” after the rack position number.
•
Do not cover an entire rack with aluminum foil or
place foil on the oven bottom. Baking results will be
affected and damage may occur to the oven bottom.
Oven Operation
(continued)
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Broiling
For best results, use a pan designed for broiling. For additional broiling tips, see “Cooking Made Simple” booklet.
Broiling Chart
Chart time based on a preheated broil element using the “HI” setting
Setting the Controls for Broiling
Foods
1. Place the oven rack on the proper rack positon.
(See following chart.)
Beef
Steak (1"):
Medium
Well
Hamburgers (3/4"):
Medium
Well
2. Press the BROIL pad.
• Indicator word BROIL will flash and three dashes will
appear.
Rack
Position*
Minutes/Side (Approx.)
1st Side
2nd Side
4o
4o
9
11
7
8
4o
4o
5
6
3-4
4-5
Pork
Chops (1/2")
Chops (1")
Ham Slice
4o
3
4o
7
10-11
4
5-6
9-10
2-3
Poultry
Breast Halves
(Bone-in)
3
11-12
9-11
Seafood
Fish Steaks,
Buttered (1")
4o
8-10
(no turning)
3. The first number pad pressed will enter “HI” broil.
• The oven has a variable broil feature which means that
a lower broil temperature can be selected. To select a
lower temperature, press the appropriate number pads
for the temperature desired after “HI” appears in the
display.
• Five seconds after entering “HI” or a temperature, the
broil element and fan will come on and the indicator
words BROIL and ON will remain in the display. (If a
lower temperature is selected, the ON indicator word
will cycle on and off with the element.)
4. Preheat five minutes until broil element is red. Cook food
according to the following broiling chart. Oven door
MUST be left open at the broil stop position during
cooking.
*An "o" after the rack number implies that the offset rack
should be used.
Note: This chart is a suggested guide. The times may vary
with food being cooked.
5. Press the CANCEL pad to turn off oven when food is
cooked.
Notes . . .
•
If more than five seconds elapse between pressing the
BROIL pad and number pad, the oven is not set and
the display will return to the previous display.
•
A cooling fan will automatically turn on during
broiling. If it does not operate, contact an authorized servicer.
•
“HI” is used for most broiling. Use a lower broil
temperature when broiling longer cooking foods or
thin pieces of food. The lower temperature allows
food to cook to the well done stage without excessive
browning.
•
Expect broil times to increase and browning to be
slightly lighter if appliance is installed on a 208 volt
circuit.
9
Clock Controlled
Oven Operations
The clock controlled oven cooking feature is used to turn the
oven off at a preset time of day or delay the start and then turn
off the oven.
After five seconds, the time of day returns to the
display.
• The temperature in the display will increase in 5°
increments until the oven reaches the preset
temperature.
The clock must be functioning and set at the correct time of
day for this feature to operate correctly.
• When the oven is preheated, the oven will chime and
the ON and PREHEAT indicator words will go off.
The feature can be used with either oven cooking or selfcleaning. See page 13 for instructions on delaying the start of
a clean cycle.
5. At the end of the programmed Cook Time, the oven will
shut off automatically and a “chime” will be heard four
times and “End” will appear in the display. Press the
CANCEL pad.
Setting the Controls
To Start Immediately and Turn Off Automatically:
If oven is not cancelled, “End” will remain in the
display and there will be one chime every minute for
10 minutes.
1. Press the BAKE or CONVECT pad.
• The indicator words BAKE or CONV BAKE will flash
and three dashes will appear.
To Delay the Start and Turn Off Automatically:
2. Press the appropriate number pads for the desired oven
temperature.
1-4. Follow preceding steps 1-4.
5. Press the STOP TIME pad. Indicator words STOP and
TIME will flash. (Display will show the calculated stop
time based on the current time of day and the cook time
that you entered previously.)
• The temperature can be set from 100° to 550° in 5°
increments.
• After five seconds the oven will begin to preheat. The
indicator words ON and PREHEAT will appear in the
display and 100° or the actual oven temperature, whichever is higher.
6. Press the appropriate number pads to enter the time you
wish the oven to stop. A stop time can only be accepted
for later in the day.
3. Press the COOK TIME pad. The indicator words COOK
TIME will flash and the display will show “0HR:00”.
Example: If at 10:00 you set the oven for 350° F and 2
hours and 30 minutes of cooking time, the calculated stop
time would be “12:30”. The display would show:
4. Press the appropriate number pads to enter cooking hours
and minutes. (Allowable range is 5 minutes to 11 hours
and 55 minutes.)
Example: If cooking time selected for convection baking
is 2 hours and 30 minutes, the display will show:
U L
U L
more . . .
10
Oven Operation
(continued)
If you want the stop time to be 1:00, press the number pads
“1,0,0”. Five seconds later, the display will briefly show
the start time of 10:30 along with the indicator words
DELAY, START TIME.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Notes . . .
•
If more than five seconds elapse between pressing a
function pad and pressing the appropriate number
pads, the oven is NOT set and display will return to
the previous display.
•
The clock controlled feature can be used with only
one oven at a time.
•
If one oven is set for clock controlled baking, the
other oven cannot be set to self-clean.
•
To recall the time programmed, press the appropriate
time pad.
At the end of the delayed period, the DELAY indicator
word will go off and the oven will begin to heat.
•
7. At the end of the programmed Cook Time, the oven will
shut off automatically and a “chime” will be heard four
times, “End” will appear in the display. Press the
CANCEL pad to turn off oven.
To cancel a timed function, hold the COOK TIME
pad for four seconds. This will only cancel the cook
time and stop time, not the set bake temperature.
•
Clock controlled cooking is not recommended for
baked items that require a preheated oven, such as
cakes, cookies, pies and breads. For these foods,
place food in preheated oven and set the timer to
signal the end of baking time.
•
Highly perishable foods such as dairy foods, pork,
poultry or seafood are not recommended for clock
controlled cooking with a delayed start.
U L
After five seconds, the display will return to the current
time of day along with the indicator words DELAY,
TIMED, and “U” or “L” indicating upper or lower oven.
U L
If the oven is not cancelled, “End” will remain in the
display and there will be one chime every minute for 10
minutes.
11
Care and Cleaning
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Self-Clean Oven
The self-clean cycle uses above normal cooking temperatures
to automatically clean the entire oven interior. While this
occurs, a device in the oven vent helps consume normal
amounts of smoke. The oven is vented through an opening
under the control panel.
Setting the Controls for Self-Clean
1. Close oven door.
2. Press CLEAN pad.
• The indicator words CLEAN TIME will flash,
the display will show “- - HR - -”, and a “U”
or “L” indicating upper or lower oven.
:
NOTE: Both ovens cannot be self-cleaned at the same time.
It is normal for flare-ups, smoking or flaming to occur during
cleaning if the oven is heavily soiled.
It is better to clean the oven regularly rather than to wait until
there is a heavy build-up of soil in the oven.
3. Press any number pad and “3:00” hours will appear in
the display for an average soiled oven.
• The cleaning time can be varied depending on the
amount of soil. Press the number pads 2, 0, 0 to
enter “2:00” hours of cleaning for light soil. The
number pads 4, 0, 0 will enter “4:00” hours for
heavy soil.
During the cleaning process, the kitchen should be well
ventilated to help eliminate normal odors associated with
cleaning.
Do not use commercial oven cleaners on the self-clean oven
finish or around any part of the oven as they will damage the
finish or parts.
• Five seconds after entering the cleaning time, the
oven door will automatically latch and the cooling
fan will come on.
Before Self-Cleaning
• The indicator words LOCK and ON will come on
when the door is latched.
Remove broiler pan, all pans and the oven racks from the
oven. The oven racks will discolor and may not slide easily
after a self-clean cycle.
• The indicator word ON will cycle with the
elements as the cleaning temperature is
maintained.
Clean oven frame, door frame (area outside the door gasket)
and around the opening in the door gasket with a nonabrasive cleaning agent such as Bon Ami or detergent and
water. These areas are not exposed to cleaning temperatures
and should be cleaned to prevent soil from baking on during
the clean cycle.
To prevent damage, do not clean
or rub the gasket around the
oven door. The gasket is designed
to seal in heat during the clean
cycle.
Wipe up excess grease or
spillovers from the oven bottom
to prevent excessive smoking, flare-ups or flaming during
the clean cycle. For ease of cleaning, the heating element
can be lifted slightly (1 to 1-1/2 inches).
Wipe up sugary spillovers and acid spillovers such as lemon
juice, tomato sauce or milk-based sauces. Porcelain enamel
is acid resistant, not acid proof. The porcelain finish may
discolor if acid spills are not wiped up prior to a self-clean
cycle.
4. When the cleaning time has been completed, the
indicator words CLEAN and ON will go off. The
indicator word LOCK and the cooling fan will remain
on until the oven has cooled and the door has unlocked.
After Self-Cleaning
About one hour after the end of the clean cycle, the
lock will disengage and the LOCK indicator word will
turn off. At this point, the door can be unlocked and
opened.
Some soil may leave a light gray, powdery ash which
can be removed with a damp cloth. If soil remains, it
indicates that the clean cycle was not long enough. The
soil will be removed during the next clean cycle.
If the oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and embossed
rack supports with a small amount of vegetable oil to
restore ease of movement.
A white discoloration may appear after cleaning if acid
or sugary foods were not wiped up before the clean cycle.
This is normal and will NOT affect performance.
12
Care & Cleaning
(continued)
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
To Delay the Start of a Clean Cycle
To Cancel Self-Clean
1-3. Follow steps 1-3 on page 12.
1. Press the CANCEL pad. The door will be locked while
the LOCK indicator word remains in the display.
4. Press the STOP TIME pad. Indicator words STOP TIME
will flash in the display and CLEAN, “U” or “L” oven, and
the calculated stop time will also appear in the display.
Depending on the length of time the oven had been
cleaning, it may take up to an hour for the oven to cool
down. When the oven is cool, the door will unlock and
the cooling fan will turn off.
5. Press the appropriate number pads to enter the stop time.
A stop time can only be accepted for later in the day.
Example: If at 9:00 you set the oven to clean for three
hours, the calculated stop time would be “12:00”. The
display will show:
Notes. . .
• CAUTION: It is normal for parts of the wall
oven to become hot during a clean cycle. Therefore, during a clean cycle, avoid touching the
oven vent area, oven door and window.
U L
•
If the oven door is left open, “door” will flash in
the display and a signal will beep until the door is
closed, or for 5 seconds and the CLEAN pad is
pressed again.
•
A fan will automatically turn on during the selfclean cycle and will automatically turn off after the clean cycle when the oven has cooled. If
it does not operate, contact an authorized
servicer.
•
If more than five seconds elapse between pressing
the CLEAN pad and pressing a number pad, the
program will automatically return to the previous
display.
•
The oven door will be damaged if the oven door is
forced to open when the LOCK indicator word is
still displayed.
•
The first few times the oven is cleaned, some
smoke and odor may be detected. This is normal
and will lessen or disappear with use. If the oven
is heavily soiled, or if the broiler pan was accidently left in the oven, excessive smoke and odor
may occur.
•
As the oven heats and cools, you may hear sounds
of metal parts expanding and contracting. This is
normal and will not damage your appliance.
If you want the stop time to be 1:00, press the number pads
“1,0,0”. Five seconds later the display will briefly show
the start time and the indicator word DELAY.
U L
After a brief time, the display will return to the current time
of day with the indicator words DELAY TIMED CLEAN
remaining in the display.
U L
When the oven begins to clean, the indicator word ON and
the cooling fan will come on. The indicator word DELAY
will go off.
When the clean time has been completed, the indicator
words CLEAN and ON will go off. The indicator word
LOCK and the cooling fan will remain on until the oven has
cooled down and the door has been unlocked.
13
Cleaning CAUTIONS:
• Be sure appliance is off and all parts are cool before
• To prevent staining or discoloration, clean appliance
handling or cleaning. This is to avoid damage and
possible burns.
• If a part is removed, be sure it is correctly replaced.
after each use.
Cleaning Chart
○
Parts
Cleaning Procedure
Broiler Pan
and Insert
Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.
• Place soapy cloth over insert and pan; let soak to loosen soil.
• Wash in warm soapy water. Use soap filled scouring pad to remove stubborn soil.
• Broiler pan and insert can be cleaned in dishwasher.
○
○
○
○
○
○
○
○
○
○
○
○
Clock and
Control Panel
○
○
○
○
○
○
○
○
○
○
○
○
○
Glass
- Oven window
- Oven door
(select models)
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Oven Racks
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
•
•
•
•
To activate “Control Lock” for cleaning see page 6.
Wipe with a damp cloth. Dry thoroughly.
Glass cleaners may be used if sprayed on a cloth first. Do Not Spray Directly on the Panel.
Do not use other cleaning sprays, abrasive cleaners or large amounts of water on the panel.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
• Wash with soap and water, glass cleaners, or mild liquid sprays. Avoid using excessive amounts
of water.
• Remove stubborn soils with nonabrasive cleaners such as Bon Ami* or a baking soda and
water paste; rinse and dry. Do not use abrasive cleaners.
○
○
○
○
Oven Interior
○
○
• Wash with soap and water or glass cleaner. Avoid using excessive amounts of water which
may seep under or behind glass.
• Do not use abrasive cleaners.
Metal Finishes
- Oven Trim
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
• See pages 12 and 13 for information on the self-clean oven.
• To remove occasional spillovers between cleanings, use a plastic, soap-filled scouring pad;
rinse well.
• Wipe up sugary and acid spillovers such as lemon juice, tomato sauce or milk-based
sauces. Porcelain enamel is acid resistant, not acid proof. The porcelain finish may
discolor if acid spills are not wiped up prior to a self-clean cycle.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
• Rub with a sponge or cloth using one of the following cleaners: Bon Ami, Soft Scrub or
Comet*. Rinse and dry.
• For hard to remove soils, use a dampened soap-filled scouring pad. Rinse and dry.
• Racks will permanently discolor and may not slide smoothly if left in the oven during a
self-clean operation. If this occurs, wipe the rack and embossed rack supports with a small
amount of vegetable oil to restore ease of movement, then wipe off excess oil.
14
○
Cleaning Chart (continued)
○
Parts
Cleaning Procedure
Plastic Finishes
- Door Handle Area
• Wash with soap and water or mild liquid sprays and a soft cloth. Do not use abrasive cleaners
or oven cleaners on plastic finishes.
• To prevent staining or discoloration, wipe up fat, grease or acid (tomato, lemon, vinegar, milk,
fruit juice, marinade) immediately with a dry paper towel or cloth.
○
○
○
○
○
○
○
○
○
○
○
○
Brushed Chrome
(select models)
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
• When cool, wash with soapy water, rinse and buff the surface.
• For heavier soil, use a mild abrasive cleaner, rubbing with the grain to avoid streaking the
surface. Rinse and buff.
• To prevent scratching, do not use abrasive or caustic agents.
• To restore luster and remove streaks, follow with Stainless Steel Magic Spray*
(Part #20000008)**.
Chrome will permanently discolor if soil is allowed to bake on.
* Brand names are trademarks of the respective manufacturers.
** To order direct, call 1-800-688-8408.
Maintenance
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Oven Light
Before replacing light bulb, DISCONNECT POWER TO
OVEN. Be sure bulb is cool. Do not touch a hot bulb with a
damp cloth as the bulb may break.
To replace oven light:
Use a dry potholder and very carefully unscrew bulb cover
and bulb. Replace with a 40 watt, oven-rated appliance bulb.
Bulb with a brass base is recommended to prevent fusing of
bulb into socket.
Replace bulb cover and reconnect power to oven. Reset
clock.
Oven Window
To protect the oven door window:
1. Do not use abrasive cleaning agents such as steel wool
scouring pads or powdered cleansers as they may
scratch the glass.
2. Do not hit the glass with pots, pans, furniture, toys, or
other objects.
3. Do not close the oven door until the oven racks are in
place.
Scratching, hitting, jarring or stressing the glass may
weaken its structure causing an increased risk of breakage
at a later date.
15
Before You Call For Service
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Check these points if . . .
•check for a blown fuse or a tripped circuit breaker.
•check if oven is properly connected to electric outlet.
The oven fails
to operate.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Oven door will
not unlock.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
•food may be positioned incorrectly in oven. (See “Cooking Made Simple” booklet.)
•oven not preheated properly.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
•the oven may be installed improperly.
•check the oven rack with a level.
•stagger pans, do not allow pans to touch each other or oven wall.
•check instructions for suggested placement of pans on oven rack. (See“Cooking
Made Simple” booklet.)
Foods bake unevenly.
○
○
•control may be improperly set.
•check rack position. (See page 9.)
•voltage into house may be low.
•broil element was not preheated.
•oven door was closed during broiling. Leave door open to first stop position.
Baked food is
burned or too
brown on top.
○
○
•oven may need longer cleaning time.
•excessive spills were not removed prior to self-cleaning process.
Foods do not
broil properly.
○
○
•controls may be improperly set.
•check if set for delayed start.
Oven did not
clean properly.
○
○
clean cycle will “burn off” the smells more quickly. Turning on a ventilation fan will
help remove the smoke and/or odor.
•excessive food soils on the oven bottom. Use a self-clean cycle.
Oven will not activate
the self-cleaning process.
○
○
•this is normal for a new wall oven and will disappear after a few uses. Initiating a
There is a strong odor
or light smoke when
oven is turned on.
○
○
•the light bulb is loose or defective.
•check power supply, circuit breaker or fuse.
•the oven light does not work during self-cleaning process.
The oven light
and/or clock does
not function.
○
○
•the controls may have been set incorrectly.
•clock controls may be set for a delayed bake function.
•the Oven Control Lockout may have been set. (See page 6.)
Clock, indicator words,
and/or lights operate
but oven does not heat.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
•oven may not have cooled to safe temperature after self-cleaning process.
16
○
○
○
○
Before You Call for Service (continued)
•the pans being used may not be of the size or material recommended for best results.
(See “Cooking Made Simple” booklet).
•there may not be sufficient room around sides of the pans for proper air circulation
in the oven.
•check instructions for preheating, rack position and oven temperature.
•check oven temperature when convection baking. Decrease conventional baking
temperatures by 25° F.
Oven baking results
are less than expected.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
The cooling fan continues
to operate after the oven
has been turned off.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Fault Codes
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
• this is normal. The fan will automatically shut off when the oven is cooled.
○
○
A fan sound
can be heard.
○
○
• oven thermostat calibration may differ between old and new ovens. Follow recipe
and use the directions in this guide before calling for service since the calibration
on the previous oven may have drifted to a too high or too low setting. (See p. 6 Adjusting Oven Temperature.)
Baking results differ
from previous oven.
○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
• this is the cooling fan and is normal. The fan will continue to run after use until
the oven cools.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
• fault codes are shown in the display as “F” and a number. If a fault code appears in
the display and beeps sound, press the CANCEL pad. If the fault code and beeps
continue after pressing cancel, disconnect power to the wall oven. Wait a few minutes, then reconnect power to the oven. If the fault code and beeps still continue,
disconnect power to the wall oven and call an authorized servicer.
• if the oven is heavily soiled, excessive flare-ups may result in a fault code during a
clean cycle. Press CANCEL pad and allow the oven to cool for one hour, then reset
the clean cycle. If the fault code and beeps still continue, disconnect power to the
appliance and call an authorized servicer.
17
If You Need Service
• Call the dealer from whom your appliance was purchased or call Maytag Appliances Sales Company, Maytag
Customer Assistance at 1-800-688-9900, USA or 1-800-688-2002, CANADA to locate an authorized servicer.
• Be sure to retain proof of purchase to verify warranty status. Refer to WARRANTY (last page) for further
information on owner’s responsibilities for warranty service.
• If the dealer or service company cannot resolve the problem, write to Maytag Appliances Sales Company, Attn:
CAIR® Center, P.O. Box 2370, Cleveland, TN 37320-2370, or call 1-800-688-9900, USA or 1-800-688-2002,
CANADA.
U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.
NOTE: When writing or calling about a service problem, please include the following information:
a. Your name, address and telephone number;
b. Model number and serial number;
c. Name and address of your dealer or servicer;
d. A clear description of the problem you are having;
e. Proof of purchase (sales receipt).
• User’s guides, service manuals and parts information are available from Maytag Appliances Sales Company,
Maytag Customer Assistance.
18
W
Y
T
RRAN
A
Maytag Wall Oven Warranty
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Full One Year Warranty - Parts and Labor
For one (1) year from the original retail purchase date, any part which fails in normal home use will be repaired or replaced
free of charge.
Limited Warranties - Parts Only
Second Year - After the first year from the original purchase date, parts which fail in normal home use will be repaired or
replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage and transportation.
Third Through Fifth Year - From the original purchase date, parts listed below which fail in normal home use will be
repaired or replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage and
transportation.
• Electronic Controls
• Electric Heating Elements: broil and bake elements on electric cooking appliances.
Canadian Residents
The above warranties only cover an appliance installed in Canada that has been certified or listed by appropriate test agencies for compliance to a National Standard of Canada unless the appliance was brought into Canada due to transfer of
residence from the United States to Canada.
Limited Warranty Outside the United States and Canada - Parts Only
For two (2) years from the date of original retail purchase, any part which fails in normal home use will be repaired or
replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage and transportation.
The specific warranties expressed above are the ONLY warranties provided by the manufacturer. These warranties give you
specific legal rights, and you may also have other rights which vary from state to state.
What is Not Covered By
These Warranties:
1. Conditions and damages resulting from any of the
following:
a. Improper installation, delivery, or maintenance.
b. Any repair, modification, alteration, or adjustment
not authorized by the manufacturer or an
authorized servicer.
c. Misuse, abuse, accidents, or unreasonable use.
d. Incorrect electric current, voltage, or supply.
e. Improper setting of any control.
2. Warranties are void if the original serial numbers have
been removed, altered, or cannot be readily
determined.
4. Products purchased for commercial or industrial use.
5. The cost of service or service call to:
a. Correct installation errors.
b. Instruct the user on the proper use of the product.
c. Transport the appliance to the servicer.
6. Consequential or incidental damages sustained by any
person as a result of any breach of these warranties.
Some states do not allow the exclusion or limitation of
consequential or incidental damages, so the above
exclusion may not apply.
3. Light bulbs.
MAYTAG •
Form No. A/03/00
403 West Fourth Street North • P.O. Box 39 • Newton, Iowa 50208
Part No. 8112P165-60
http://www.maytag.com
Litho U.S.A .