Craftsman 390.262553 Owner`s manual

SEARS
OWNER'S
MANUAL
MODEL NOS.
390.262454
390.262553
MODELNO.
390.262454
390.262553
390.262653
MODEL
NO. 390.262653
I:RI:IF'rSMg N°
CAUTION:
Read and Follow
All Safely Rulesand
Operating Instructions
Before First Useof
ThisProduct.
Save ThisManual For
Future Reference.
HYDROGLASS ®
HIGH PRESSURE
SPRINKLER PUMP
• Safety Instructions
• Installation
• Electrical
•Maintenance
• Repair Pa_s
Sears, Roebuck and Co., Hoffman Estates, IL 60179
PRINTED
IN
U.S.A.
U.S.A.
Form No.
F642-9908
(Rev. 8/18/03)
CONTENTS
INTRODUCTION
INTRODUCTION/XVARRANTY ..........................................
2
SAFETY ...............................................................................
2
PREPARATION ....................................................................
3
INSTALLATION ................................................................
3-4
ELECTRICAL.....................................................................
54
OPERATION ........................................................................
7
MAINTENANCE ...............................................................
TROUBLESHOOTING .......................................................
REPAIR PARTS ..................................................................
FULL ONE
Please take a few minutes to read our instructions
before you
install and use ynur pump. Tbis will help you obtain the full
benefits from this pump. It will also help you avoid any needless service costs that result from causes we cannot control
alld
cannot
cover
ill ottr
vvarranty.
8-9
10
11
YEAR WARRANTY
ON CRAFTSMAN*
SPRINKLER
PUMPS
For one year from the date of purchase. Sears will repair or replace this pump, free of charge, if defective in materials or workmanship.
LIMITED
WARRANTY
ON CRAFTSMAN
® HYDROGLASS
®SPRINKLER
PUMP
After one year and through
two years from the date of purchase.
part for any defective part. You pay for labor.
This warranty
ure to install,
Sears will furnish,
free of charge,
a replacement
does not cover repairs on replacemellt
parts necessary because of abuse or negligence
adiust and operate this pump according
to the instructions
in the owner's manual.
LIHITATION
OF LIABILITY
including
fail-
SEARS WILL NOT BE LIABLE FOR LOSS OR DAMAGE
TO PROPERTY OR ANY INCIDENTAL
OR CONSEQUENTIAL
LOSS OR. EXIa_._ SE_ROM PROPERTY
DAMAGE DUE DIRECTLY
OR INDIRECTLY
FROM THE USE OF THIS
Some states
or exclusi0rr
do_ot allow the exclusion
may not apply to you,
WARRAIWJ'Y SERVICE IS AVAILABLE
MENT IN THE UNITED STATES.
or limitation
BY SIMPLY
only wlaiie the product
of incidental
CONTACTING
is in the United
or consequential
THE NEAREST
damages,
so the above
SEARS SERVICE
limitation
CENTER/DEPART-
This warranty
applies
This warranty
gives you Specific legal fights, and you may also have other rights which vary fIom state to state.
Sdaa"s, Roebuck
and Co., Dept. 817 WA, Hoffman
Estates,
IL 60179
States.
RULES FOR SAFE INSTALLATION
Carefully
read and follow
manual
or on pump.
all safety
instructions
in this
This is the safety alert symbol.
When you see this
symbol on your pump or in this manual, look for one of the
following signal words and be alert to the potential
for personal injury!
_
DANGER
serious personal
ignored.
warns
about
death
or major
injury,
{_'WARNIN_wARNING
warns
cause serious personal
age ff ignored.
injury, death
_ .....
CAUTION
IONj CAUTION
can cause
noted.
minor
personal
warns
injury
hazards
about
that will cause
property
hazards
or major
about
that
property
hazards
or property
damage
that
damage
Tim word NOTICE indicates special instructions
important but not related to hazards.
if
can
damwill or
if ig_
which are
l.To avoid risk of serious bodily injury and property damage, read safety instructions carefully before installing
pump.
AND
OPERATION!
2.Follow local and/or national plumbing and electrical
codes when installing pump.
3. Keep the well covered while installing pump to prevent
leaves and other debris from falling into well, contaminating well and possibly damaging pump.
4. Protect pump and piping system from freezing. Allowing
pump or water system to freeze could severely damage
pump and voids warranty.
!_WAFINING]Hazardous
Voltage. Can shock, burn,
cause death, or start fires.
5. Disconnect electrical power source before installing or
working
on pump.
6. Ground pump with a ground
wire run from grounding
lug
on motor to a grounded lead in the service panel.
7. Line winagc
and frequency
of electrical power supply
nlust agree with motor nanmplate.
8 Ilse of fuses or wire smaller than size recommended in
owner's manual can cause overheating, possible fires, and
will void warranty.
9. Pump water only with this pump.
10. Do not run pump dry. To do so will damage seals and can
cause leaking and property damage.
PREPARATION
BASIC
TOOLS
AND
INSTALLATION
MATERIALS
NEEDED
Pipe Wrenches
Hacksaw
Screwdriver
Check Valve
Adjustable
Knife
Teflon
NOTICE:
Wrench
Depth
to water
(Continued)
Suction Pipe
iTee
and Plug
Tape
must not be more
than 20'.
Sanitary
Well Seal
1. Long runs and many fittings increase friction and reduce
flow. Locate pump as close to water source as possible:
use as few elbows and fittings as possible.
2. Be sure water is clear of sand. Sand will plug the pump
and void the warranty.
3.
4.
/
Protect pump and all piping from freezing. Freezing will
split pipe, damage puthp and void the warranty.
Check
locally for frost protection
requirements
(usually pipe
must be 12" below frost line and pump must be insulated).
Be sure
shape.
all pipes
and foot valve
are clean
No air pockets in suction
No leaks in suction pipe.
Stik' to seal pipe joints.
7.
Unions installed near pump and water
servicing. Leave room to use wrenches.
8.
IAWARNING]Pump
body
may explode
booster
pump.
DO NOT use in a booster
Chemical
and in good
Strainer
5.
6.
' Lake
Foot
Valve
Co., Chicago,
pipe.
Use Teflon tape or Plasto-Joint
source
v/ill aid in
if used as a
application.
2590 0996
Figure
I - Cased/Dug
DRIVEN
POINT
Well Installation
INSTALLATION
1. Connect the suction pipe to the drive point as illustrated in
Figure 2. Keep horizontal pipe run as short as possible. Use
Teflon tape on male pipe threads. Multiple well points may
be necessary to provide suf_cient water to pump.
Illinois.
2.
INSTALLATION
Install a check valve in piping as shown in Figure
arrow on check valve must point toward pump.
NOTICE: Use the installation method below which matches
your well type.
CASED
1. Inspect
strainer
2.
3.
WELL
Suction Pipe
to Pump
INSTALLATION
foot valve to be sure
to be sure it is dean.
it works
freely.
Inspect
Check_
Valve
Connect foot valve and strainer to the first length of suction pipe and lower pipe into well. Add sections of pipe
as needed, using Teflon tape on male threads. Be sure that
all suction pipe is leakproof or pump will lose prime and
fail to pump. install foot valve 10 to 20 feet below the lowest level to which water v/ill drop while pump is operating (pumping
water level). Your well driller can furnish
this information.
Drive point 1_
below waterT
level
__
Drive
Coupling
Drive
Point
To prevent sand and sediment
from entering the pumping system, the foot valve/strainer
should be at least 5 feet
above the bottom of the well.
4. When the proper depth is reached, install a sanitary well
seal over the pipe and in the well ca_mg. Tighten the bolts
to seal the casing.
5. When using a foot valve, a priming
in Figure 1 are recommended.
tee and plug as shown
Follow cased
well installation,
steps
2589 0996
Figure
2 - Driven
HORIZONTAL
DUG WELL OR OPEN WATER
INSTALLATION
1.
2. Flow
1, 2, 3 and 5.
Point
Installation
PIPING
FROM
WELL
TO
PUMP
1. Never install a suction pipe
tion tapping of the pump.
that is smaller
than
the suc-
INSTALLATION
2. To aid priming on driven point installations,
install a line
check valve as shown in Figure 2. Be sure check valve
flow arrow points toward pump.
DISCHARGE
PIPE
SIZES
(Continued)
sprinkler
is shown
Do not use
application.
When the pump is set away from the points of water use,
the discharge
pipe size should be increased
to reduce
pressure
losses caused by friction.
• Up to 100' run: Same size as pump
discharge
• 100' to 300' run: Increase
one pipe size.
• 300' to 600' run: Increase
two pipe sizes.
LAWN
SPRINKLING
tapping.
This pump is designed for lawn sprinkling.
It is designed to
deliver plenty of water at full sprinkler pressure. It can pump
from a pond, cistern or well points.
Pump
discharge
can be divided
to supply
PUMP
two (2) or more
a pressure
tank
discharge
or
to service
booster
pump
Installation
INSTALLATION
NOTICE: Use Teflon tape supplied with the pump for making all threaded connections
to the pump itself. Do not use
pipe joint compounds
on the pump:
they can react with
the plastic in the pump components.
1. Bolt pump
APPLICATION
in
multiple
Pump/Piping
1. If increasing
discharge pipe size, install reducer in pump
discharge
tapping. Do not increase pipe size by stages.
2.
systems. A suggested
in Figure 3.
to solid, level foundation.
2.
Support
3.
Wrap 1-1/2 to two layers of Teflon tape clockwise
(as you
face end of pipe) on all male threads being attached
to
pump.
Tighten joints hand tight plus 1-1/2 turns. Do not over-
4.
all piping
connected
to the pump.
tighten.
NOTICE: Install pump as close to water source as possible.
Long piping runs and many fittings create friction and reduce flow.
To
Service
Priming
Plug
Use schedule 80 or iron pipe. See "Well Pipe Installation"
more information.
Valve
846 O494
Figure
3 - Multiple
DISCHARGE
PRESSURE
PSI
10
15
20
25
30
35
40
45
5O
DISCHARGE
PIPE TAPPING
SUCTION
PIPE TAPPING
Discharge
TABLE II - PERFORMANCE
390.262454
1 H.P,
5'
55
51
45
38
31
23
17
10'
49
46
42
35
28
19
13
15'
48
45
39
32
24
16
6
20'
45
44
37
29
20
11
-
CHART
Figure 4 - Bolt Pump
Figure 5 - Independently
Down
Support All Piping
Attached To Pump
(IN GALLONS
390.262553
1-1/2 H,P.
PER MINUTE)
DISTANCE ABOVE TO WATER
5'
10'
15'
20'
67
61
56
46
66
58
55
45
61
56
54
44
55
52
51
43
48
45
44
37
39
37
34
28
33
27
20
11
18
14
8
-
390.262653
2 H.P.
5'
69
65
59
52
47
42
34
25
14
10'
67
63
56
50
45
38
30
18
7
1-1/2" NPT
1-1/2" NPT
2" NPT
1-1/2" NPT
1-1/2" NPT
2" NPT
15'
65
60
54
48
42
35
27
13
20'
62
58
52
45
40
32
23
10
for
ELECTRICAL
Connection
diagram for dual voltage, single-phase
motors.
Your dual-voltage
motor's terminal board (under the motor
end cover) will match one of the diagrams below. Follow
that diagram if necessary
to convert
motor to 115 Volt
power.
Connect power supply wires to L1 and L2. For 3-phase motors, or if motor does not match these pictures, follow the
connection
diagram on the motor nameplate.
230 Volt to 115 Volt Conversion, Plug-in Type:
Move plug to change voltage.
230 Volt to 115 Volt Conversion, Plug-in Type:
1. Pull plug
straight
out from
terminal
board;
2.
Plug in again
with arrow
on plug
pointing to
'115 Volts'.
V
,gPoinl
Power Supply Wires
Clamp the power cable to prevent
strain on the spade connectors.
Clamp the power cable to prevent
strain on the terminal screws.
Connect the green (or bare copper) ground
wire to the green ground screw.
Connect the green (or bare copper) ground
wire to the green ground screw.
Figure 6 - I 15/230V Dual Voltage Single Phase Wiring
[AWARNIN_Hazardous
cause death. Disconnect
pump or motor. Ground
supply.
Diagram.
A
Use wire size specified
in Wiring
Chart
If possible,
connect
pump
to a separate
circuit
with no other
appliances
on it.
voltage.
Can shock,
burn, or
power to motor before working on
motor before connecting
to power
3782tooo
WIRING
Wire
motor
according
to diagram
on
nameplate.
If nameplate
diagram
differs
diagrams
above, follow
nameplate
diagram.
AGround
motor
before
connecting
to electrical
power
supply.
Failure to ground
motor can cause
severe or fatal electrical
shock
hazard.
1. Install, ground, wire and maintain
this pump in accordance with electrical
code requirements.
Consult your
local building inspector
for information
about codes.
ADo
not ground
A
(Page 6).
branch
to a gas supply
motor
from
2. Provide a correctly fused disconnect
switch for protection while working on motor. Consult local or national
electrical codes for switch requirements.
line.
A
To avoid dangerous
or fatal electrical shock, turn
OFF power to motor before working on electrical connections.
A
Supply voltage must be within +10% of nameplate voltage. Incorrect
voltage can cause fire or
damage motor and voids warranty. If in doubt consult
a licensed electrician.
5
ELECTRICAL
(Continued)
wiring diagram on motor nameplate against Figure 6. If the
motor wiring diagram does not match the diagrams in
Figure 6, follow the diagram on the motor.
3. Disconnect
power before servicing motor or pump. If the
disconnect
switch is out of sight of pump, lock it open
and tag it to prevent unexpected
power application.
4. Ground the pump permanently
using a wire of the same
size as that specified
in wiring
chart (below).
Make
ground connection
to green grounding
terminal under
motor canopy marked GRD. or @.
5.
IMPORTANT:
shipped
from
power supply
connect motor
as received on
Connect
ground wire to a grounded
lead in the service
panel or to a metal underground
water pipe or well casing at least 10 feet long. Do not connect to plastic pipe or
insulated fittings.
6.
Protect current carrying and grounding
cuts, grease, heat, oil, and chemicals.
7.
Connect current
L2 under motor
carrying
canopy.
conductors
8.
Motor has automatic
internal thermal overload
protection. If motor has stopped for unknown
reasons, thermal
overload may restart it unexpectedly,
which could cause
injury or property damage. Disconnect
power before servicing motor.
9.
If this procedure
consult a licensed
from
conductors
to terminals L1 and
When replacing
motor, check
WIRING
Recommended
115/230
Volt single
phase
models
are
factory with motor wired for 230 volts. If
is 115 volts, remove
motor canopy and reas shown in Figure 6. Do not try to run motor
115 volt current.
or the wiring
electrician.
diagrams
are confusing,
CHART
Wire
and Fuse Sizes
DISTANCE IN FEET FROM MOTOR TO METER
0 I
Branch
Fuse*
Rating*
Amps
Min.
Wire
Size
TO
50'
51'
TO
100'
101'
201'
TO
TO
200'
300'
WIRE SIZE
301'
TO
400'
401'
TO
500'
Pump
Model
HP
Volt
Max.
Load
Amps
390.262454
1
115
230
14.2
7.5
20
15
12
14
12
14
12
14
8
14
6
14
6
12
4
10
390,262553
1-1/2
115
230
10.2
9.6
25
15
10
14
10
14
10
14
8
14
6
12
4
10
4
10
390.262653
2
230
12.0
15
14
14
14
14
12
10
10
*Dual element or Fusetmn time delay fuses recommended for all motor circuits.
6
OPERATION
PRIMING
THE
PUMP
NOTICE: 'Priming' refers to the pump expelling all air in the
system and beginning
to move water from its source out into
the system. It does not refer only to pouring water into the
pump (although
pouring water in is usually the first step).
NOTICE: NEVER run pump
dry. Running pump
water in it will damage seals and can melt impeller
fuser. To prevent
damage, fill pump
with water
starting.
1. Remove
priming
plug (Figure
without
and difbefore
7).
Figure 9 - Run Ten Minutes Or Less
If no water is produced within 10 minutes, stop pump,
release all pressure, remove priming plug, refill and try
again.
[AWARNING] Hazardous pressure
and risk of explosion and scalding. If pump is run continuously
at no
flow (that is, with discharge shut off or without priming), water may boil in pump and piping system.
Under steam pressure,
pipes may rupture, blow off of
fittings or blow out of pump ports and scald anyone
near.
Figure
7 - Remove
Priming
Plug
2.
Make sure suction and discharge valves and any hoses
discharge
side of pump are open.
3.
Fill pump
and suction
pipe
on
with water.
Figure
10 - Do Not
Shut Off
To prevent
Figure
4.
8 - Fill Pump
Replace
priming
tighten plug.
using
Teflon
With
Discharge
do the following:
A. Be sure discharge
(valve, pistol grip hose nozzle,
open whenever
pump is running.
Before Starting
plug,
explosion,
Run Pump
tape
on
etc.) is
B. If pump fails to produce water when attempting to prime,
release all pressure, drain pump and refill with cold water
after every two attempts.
thread;
C. When priming, monitor pump and piping temperature. If
pump or piping begin to feel warm to the touch, shut off
pump and allow .system to cool off. Release all pressure
in system and refill pump and piping with cold water.
NOTICE: If a priming tee and plug have been provided
for a long horizontal
rnn, be sure to fill suction pipe
through this tee and replace plug. (Don't forget to Teflon
tape the plug.)
5. Start pump: water shonid be produced
in 10 minutes or
less, the time depending
on depth to water (not more
than 20') and length of horizontal
run (10' of horizontal
suction pipe = 1' of vertical lift due to friction losses in
the pipe).
7
MAINTENANCE
Pump and piping need not be disconnected
to repair or replace motor or seal (see Figure 12). If motor is replaced,
replace the shaft seal (Key No. 6, Page 11). Keep one on hand
for future use.
2.
If impeller must be replaced, loosen two machine
and remove motor canopy (see Figure 14).
Be sure to prime pump before starting.
NOTICE:
Check motor label for lubrication
instructions.
The mechanical
shaft seal in the pump is water lubricated
and serf-adjusting.
NOTICE: Drain pump
when it might freeze.
PUMP
when
disconnecting
from service
_WARNING
To avoidelectrical
shockhazard,use
insulated-handle
screwdriverto short
capacitorterminals
as shown.
or
DISASSEMBLY
1. Disconnect
NOTICE:
power
to motor.
Figure
Mark wires for correct
I I - Disconnect
clamp
14 - Hold
Remove
3.
Remove pump base mounting
bolts. Motor assembly and
back half of pump can now be pulled away from pump
front half (Figure 12). CAREFULLY remove O-Ring.
AWARNING]Capacitor
voltage
may be hazardous.
To discharge
capacitor,
hold insulated
handle screwdriver BY THE HANDLE and short capacitor
terminals
together (see Figure 14). Do not touch metal screwdriver
blade or capacitor terminals. If in doubt, consult a qualified electrician.
4.
Unscrew capacitor clamp and remove
disconnect
capacitor wires to motor.
5.
6.
Slide 7/16" open end wrench
in behind spring loaded
switch on motor end of shaft; hold motor shaft with
wrench
on shaft flats and unscrew
impeller by turning
counterclockwise
when looking into eye of impeller.
To reinstall, reverse steps 1 through 5.
7.
See directions
Power
2.
(see Figure 12).
REMOVING
Figure 12 - Slide Motor
Back
CLEANINGIREPLACING
NOTICE:
sembly".
First, follow
Shaft
assembly.
3,
Figure
screws
under
"Pump
capacitor.
Reassembly,"
Do not
Page 10.
OLD SEAL
1.
Follow instructions
2.
Follow steps
Impeller.
under
3.
Unscrew
four nuts holding pump back half to motor.
Remove rotating half of seal by placing two screwdrivers
under back half of pump body and carefully prying up
(Figure 15). Back half of pump body will slide off shaft,
bringing seal with it.
2 through
"Pump Disassembly
5 under
".
"Cleaning/Replacing
IMPELLER
instructions
under
"Pump
Disas-
1. Remove four screws fastening diffuser to seal plate; remove diffuser (see Figure 13). Exposed impeller can now
be cleaned.
Figure
15 - Remove Seal plate
NOTICE: Be sure you do not scratch or mar shaft; if shaft is
marred, it must be dressed smooth with fine emery or crocus cloth before installing new seal. DO NOT reduce shaft
diameter!
Figure
13 - Remove Diffuser
MAINTENANCE
4.
Place pump body half face down on flat surface
out stationary half of seal (see Figure 16).
(Continued)
9.
and tap
Hold motor shaft with 7/16" open end wrench on shaft
flats (Figure 14, Page 8) and screw impeller onto shaft. Be
sure you do not touch capacitor
terminals
with
body or any metal object. Tightening
impeller will automatically locate seal in correct position.
10. Remount
PUMP
diffuser
on pump
body haft with five screws.
REASSEMBLY
1. Clean O-Ring and O-Ring groove.
2.
Figure
Put O-Ring in groove on face of flange; put pump
together (see Figure 18).
halves
16 - Tap Out Seal
INSTALLING
NEW
SEAL
1. Wet outer edge of Rubber Cup on ceramic seat with liquid soap. Be sparing!
2. Put clean cardboard
washer on seal face. With thumb
pressure, press ceramic seal half firmly and squarely into
seal cavity in seal plate (see Figure 17). Polished face of
ceramic seat is up. If seal v_fll not seat correctly, remove,
placing seal face up on bench. Reclean cavity. Seal should
now seat correctly.
Figure
3.
Figure
3.
Pump
BE SURE inside of clamp is clean. Place clamp on pump
halves; snug up. Alternately
tighten screw and tap clamp
with mallet to seat O-Ring (see Figure 19).
17 - Press in New Seal
ffseal does not seat correctly after recleaning cavity, place
cardboard
washer over polished seal face and carefully
press into place using a piece of standard 3/4" pipe as a
press.
NOTICE:
4.
18 - Assemble
Be sure you do not scratch
seal face.
Dispose of cardboard
washer and recheck
sure it is free of dirt, foreign particles,
grease.
5. Inspect
seal face to be
scratches
and
shaft to be sure it is free of nicks and scratches.
6.
Reassemble
pump
is right side up.
body half to motor
flange.
7.
Apply liquid soap sparingly (one drop is sufficient)
side diameter
of rotating seal member.
Figure 19 - Tap Clamp While
BE SURE it
to in-
4. Replace
5. Replace
8.
Slide rotating seal member (carbon face first) onto shaft
until rubber drive ring hits shaf_ shoulder.
NOTICE: Be sure not to nick or scratch carbon face of seal
when passing it over threaded
shaft end or shaft shoulder.
The carbon surface must remain clean or short seal life will
result.
6.
7.
9
base mounting
motor wiring;
Prime pump according
Check for leaks.
Tightening
bolts.
close draincock.
to instructions.
See "Operation."
TROUBLESHOOTING
SYMPTOM
Motor will not run
POSSIBLE CAUSE(S)
1. Disconnectswitch is off
2. Fuse is blown
3. Startingswitchis defective
4. Wires at motorare loose,
disconnected,
CHART
CORRECTIVE ACTION
f. Be sure switchis on
Replace fuse
3. Replace startingswitch
4. Refer to instructions on wiring. Check and tighten all wiring.
2.
or wired incorrectly
['_WARNINGI Capacitor voltage may be hazardous. To discharge
capacitor, hold insulated handle screwdriver BY THE HANDLE
and short capacitor terminals together. Do not touch metal
screwdriver blade or capacitor terminals. If In doubt, consult a
qualified electrician.
Motor runshot and
overloadkicks off
Motor runs but no
water is delivered
*(Note: Check
prime before looking for other
causes. Unscrew
1. Motor is wired incorrectly
2. Voltage istoo low
"1. Pump in new installationdid
not pick up prime through:
a. Improper priming
b. Air leaks
c. Leaking foot valve
*2. Pump has lost prime through:
a. Air leaks
b. Water level below suction
of pump
1. Refer to instructionson wiring
2. Check with power company. Installheavier wiringif wire
size is too small (See Electrical,Pages 5 and 6)
1. In new installation:
a. Re-prime according to instructions
b. Check all connections on suction line
c. Replace foot valve
2,
In installation already in use:
a. Check all connections on suction line and shaft seal
b. Lower suction line into water and re-pdme. If receding water level
in well exceeds suction lift, a deep well pump is needed
3.
Clean impeller; see Maintenance
4. Replace check valve or foot valve
priming plug and
see if there is
3. Impeller is plugged
4. Check valve or foot valve is stuck
water in priming
hole.)
5
in closedposition
• Pipes are frozen
6. Foot valve and/or strainerare
buried in sand or mud
5. Thaw pipes. Bury pipes below frost line• Heat pit or pump house.
6. Raise foot valve and/or strainerabove well bottom
Pumpdoes not
deliver water to full
1. Water level in well is lower than
estimated
1. A deep well jet pump may be needed (over 20 ft. to water)
capacity (Also
check point 3
immediately above
2. Steel piping (if used) is corroded or
limed, causing excess friction
3. Offset piping is too small in size
2. Replace with plastic pipe where possible, otherwise with new
steel pipe
3. Use larger offset piping
Pump leaks
around clamp
1. Clamp loose
1. STOP PUMP, tighten clamp nut 1-2 turns. Alternately tighten nut and
and tap clamp with mallet to seat O-Ring. Do not overtighten
10
REPAIR
PARTS
8A
11A
3
10
y
20
3
4
I F>mr,'_
SearsProductService,1-800-366-7278
Key
No
1
1A
1B
IC
2
3
4
5
6
7
8
8A
9
10
11
11A
12
13
14
16
17
16
19
20
21
1.
12"
390.262454
115/230V
60 Cyll Ph
1 HP
part
Descriptzon
Motor
Overload Protector
Terminal Board
Contactor
Governor
J218-1029
Capacitor
Shnger
Priming Plug 1/2' NPT
Tank Body Back Half Complete
O-Rkng
Shaft Seal for 5/8" Sha6
Impeller
Impeller Screw
D_ffuser
Diffuser
Screw - #8 - 32 RH
(1 and 1-1/2HP
4Req'd
Lockwasher
, .....
390 262553
115/230V
60 Cy/1Ph
1-1/2 HP
17351-0009
WC78-39T
L176-47P1
U9-399
U109-6A
C105-92PVB
J218-956C
U18-1342
U18-1180
U18-1098
U18-128
U18-525
17351-0009
WC78-39T
L176-47P1
U9-399
U109-6A
CI05-92PBBB
C1-258PCA
C1-258PCA
U30-869SS
U30-869SS
C19-54SS
C176-53PA
C19-54SS
C176-53PA
U212-68T
U9-226
C4-42P
U43-61ZP
U36-37ZP
C35-11
U4311ZP
U212-68T
U9-226
C4-42P
U43 61ZP
U36-37ZP
C35-11
U43-11ZP
396.262653
230V
60 Cyll Ph
2 HP
A100GSL
U18-1406
U18-1180
U18-1095
U18-128
U18-525
17351 0009
WC78-39T
C3-189P1
U9-228A
U109-6A
C105-214PFA
C30-51SS
C1-274P
2HP
u30-642SS
2Req'd)
'V" Clamp
Tank Body Fron_ Half (Incl NO 12)
Tank Body Front Half Complete (Incl Nos 3 and 12)
[3ralncoek - 1/4 NPT
O-Ring
Base
Flat Washer 5/16 (2 Req'd )
Nut - 5/16 - 18 t4 Req d )
Rubber Pad
Lock Washer - 5/16 (2 Req d )
Capscrew, 3/8 - 16 x 1-3/4" (2 Req'd )
Flat Washer 5/16 (2 Req'd )
Capscrew, 3/8 - 16 x 1" (2 Req'd )
U43-21SS
C19-37A
C176-62PA
U212-68T
U9-393
C4-42P
C35-11
U30-77SS
U43-42SS
U30-748S
• NOt dluslrated
I1
10
S£ A[RS
CRgFTSMRN°
OWNER'S
MANUAL
HYDROGLASS ®
HIGH PRESSURE
SPRINKLER PUMP
Model No.
390.262454
390.262553
390.262653
Forthe repair or replacementpartsyou need
Call7 am - 7 pm, 7 daysa week
t -8OO-366-PART
(1-800-366-7278)
Forin-homemajorbrandrepairservice
Call24 hours a day,7 daysa week
1-8OO-4-REPAIR
(1-800-473-7247)
The model number of
your Sprinkler Pump will
be found on a plate
attached to the side of
the pump body.
When requesting service
or ordering parts, always
give the following
information:
• Product Type
• Model Number
• Part Number
• Part Description
Forthe locationof a
SearsRepairServiceCenterin yourarea
Call24 hours a day,7 daysa week
1-800-488-1222
Forinformationon purchasinga Sears
MaintenanceAgreementor to inquire
aboutan existingAgreement
call g am - 5 pro, Monday-Saturday
A
1-800-827-6655
SEARS
America_
Repair Speciahsts
Sears, Roebuck and Co., Hoffman Estates, IL 60179
U.S.A.