WangYe WY50QT-58 User`s manual

User’s manual :WY50QT-58
PREFACE
Thanks for your purchasing the motorcycle WY50QT-58, and sincerely welcome
you to be our motorcycle user. To enjoy a more safe and pleasurable driving, firstly
please familiarity with the manual must carry on before driving. Your personal
safety depends not only on the vigilance and familiar operation skills, but also
relates to whether you are familiar with the mechanical performance. Before driving,
check-up and periodical maintenance are basic requirement. If maintenance and
repair needed, go to our service center for help. If you know the mechanic
knowledge and have the tools, the dealer can offer you help with the maintenance
and repair, like providing the parts catalogue and the spare parts.
This manual explains in detail the correct operation and maintenance, together
with the expectation for your long-time use. Modifications in specification could
cause the discrepancy with some figures and content in the manual, we feel sorry
for that and hold the final right of interpretation. Have a good enjoyment and thanks
again for your purchasing.
The important points to attention
l
The driver and passenger
This motorcycle is limited to one driver. Never exceed the max load capacity of motorcycle.
l
For the safety, avoid driving the motorcycle in atrocious weather or cold weather (under -12℃).
l
For the road condition
Only drive on the highroad.
The caution banners about the safety or environment protection stick to the sundries box cover, the
rear carrier, and fuel tank cap. (Being visible before or during driving)
l
Modifications in specification could cause the discrepancy with some figures and content in the
manual, we feel sorry for that and hold the final right of interpretation.
l
Please read the user’s manual carefully
You must pay attention to the warning sentence or paragraph.
WARNING
Not following the operation instruction in this manual may cause great damage to you.
ATTENTION
Not following the operation instruction in this manual may cause injury to both you and vehicle.
Regard this manual as a permanent part, even when transfering the vehicle to a new owner, transfer
the manual at the same time.
Contents
Ⅰ. Notice for safe driving
Rules for safe driving …………………………1
Payload…………………………………………2
Ⅱ. Various parts name and instruction
Parts & subassemblies…………………………3
Meter and indicator……………………………5
Ignition switch………………………………5
Fuel meter……………………………………6
Lighting switchs ……………………………6
Starting switch ………………………………6
The front light change switch………………7
Turning signal light switch …………………7
Horn switch …………………………………7
Steering lock…………………………………7
Cushion lock ………………………………8
Ⅲ、Operation instruction
Check up before driving………………………9
Start engine………………………………… 13
Drive motorcycle ……………………………14
Driving operation ……………………………15
Brake operation………………………………15
Power off the engine…………………………16
Parking operation ……………………………17
Ⅳ、Maintenance and service
Maintenance periodic form ……………………19
Solution for troubles …………………………21
Clean the air filter …………………………23
Battery maintenance …………………………23
Idle speed adjustment ………………………24
Change oil and clean the filter net………………25
Change the gear oil …………………………26
Spark plug……………………………………27
Fuse replacement ……………………………27
Ⅴ、Vehicle storage…………………………28
Ⅵ、Vehicle identification……………………29
Ⅶ、Tool set………………………………30
Ⅷ、Main technique Parameter………………31
Ⅸ. Circuit diagram…………………………33
Ⅹ.Emission Control System Warranty
Statement …………………………………34
Ⅰ.Notice for safe driving
Rules for safe driving
1. Many traffic accidents are caused by the inability of car driver to notice the motorcyclist, so the
motorcyclist should try his best to be noticed by other drivers. For example:
l
2.
Put on the coat in bright color.
l Drive with great caution in the place with dazzling light or in blind spot. .
Particular care should be exercised at the level crossing of roads, entrance and exit of parking lot
or on the automobile lane.
3.
Never overspeed , otherwise accidents may occur.
4.
You must get the driving license and be familiar with the vehicle. Never lend the vehicle to the
man without driving license or who is unfamiliar with motorcycle.
5.
Avoid driving on the rough road. This can easily result in the operation failure and structural
damage to the vehicle frame
6.
Check up before driving. (Look at page9)
7.
When driving, hold the handlebars and put feet on the footrest.
8. Don’t drive too close to the other vehicles. Never contend for lane, and strictly observe the local
traffic.
-1-
Payload
l
Admonition:
Only put light goods in sundry boxes or other deposited place.
The deposited shouldn’t be overweighted according to the following blank 1:
Blank 1
Deposited
Weight (kg)
Carrier
5kg
Rear Box
5kg
l
The max payload of this motorcycle is 75kg, including the weight of the driver and
goods.
l
If the motorcycle is over loaded, it will affect the stability and operation of the
motorcycle.
l
Tie all the goods needed to be carried on the motorcycle.
l
On the rear shelf seats no child
-2-
Ⅱ. Various parts name and instruction
Parts & subassemblies(Fig1、Fig2)
Fig1
-3-
Fig2
The broken line(……)indicate the parts unseen in the picture
-4-
Meter and indicator(Fig3)
⑴Fuel meter: Indicate the fuel volume in the fuel tank
⑵Right turning signal : Sparkling when the button turns right
⑶odometer: Record the mileage
⑷Speedometer: show the speed when the vehicle running.
⑸High beam indicator : When the button is on position“
”,the high
beam indicator works
Fig3
⑹Left turning signal : Sparkling when the button turns left
Ignition switch(Fig4)
⑴Open(
)—when the switch turns to this position,
engine is started and do not pull out the key.
⑵Close(
)—when the switch turns to this position,
engine is stopped and take out the key.
⑶Lock(
)—when the switch turns to lock(
Fig4
)position, take out the key, don’t turn the
handlebar, and don’t start the engine or turn on any light.
-5-
Fuel meter(Fig5)
•
Fuel meter (1) indicate the fuel volume in the fuel tank. When the needle
points to (F), it indicates that the effective residue fuel is 5L.
When the needle points at red section, it indicates the remainder of fuel is 1.2L
Fig5
Lighting switches (1)
(Fig6)
Lights, a total of three position switch ,is “ ” 、“
”and “•”
“ ” In this position, Headlight, position lamps, rear lamps and instrument
lights
“ ” In this position, the position lamps, rear lamps and instrument lights.
“•” In this position, the headlight, rear lamps, position lights and instrument
lights will be shut down.
Starting switch(2)
(Fig6)
Press this button, the engine is started.(See P13)
Fig6
-6-
The front light change switch 1(Fig7)
Press“
”button,to get high beam;Press“
”button,to get low beam
Turn signal light switch 2(Fig7)
When the switch is on“ ”turn left,When the switch is on“ ”button, turn
right. Press it down the light turn off.
Horn switch 3(Fig7)
Press switch, the horn make sound.
Fig 7
Steering lock(Fig 8、Fig 9)
Turn handle left to end, press down ignition key to ( ),the steering setting are locked. Do the
above opposite, it is unlocked.
-7-
Fig8
Fig9
Cushion lock(Fig 10)
•
Insert the key 1 into the key hole 2, then turn the key clockwise to
open the cushion.
•
Press down the cushion until a closedown voice is heard. Pull up the
cushion’s rear side to make sure the cushion is locked well, then take
out the key.
-8-
Fig10
Ⅲ. Operation instruction
Check up before driving
For safety and preventing trouble or accident, pre-check up is necessary.
Gasoline
When the pointer or fuel meter is close to red section, replenish oil. And check
whether the tank and the carburetor are in good condition.
•
Gasoline tank container:5L
•
Turn the tank cover anti-clockwise to open the fuel tank (Fig11)
•
Proposal gasoline, octane number is 90 above.
•
Do not replenish oil together with water, dust or other things
Fig 11
NOTICE:
•
Gasoline is inflammable, it possibly causes fire even exploding on certain condition,
replenish oil only in an airiness place after stopping the engine, no fire in the place of oil
replenishment or oil storage.
•
Don’t make the top level of fuel above the inlet tube of fuel tank when replenishing, lock
the tank well after replenishment.
•
Gasoline is poisonous, keep your skin or eyes away from it, put it out of touch of
children. If swallow any gasoline unconsciously, see a doctor at once.
-9-
Inspection of Engine Oil
Inspect the engine oil level(Fig12、Fig13)
1.
Keep the motor steady on the ground, screw up the oil dip rod
and clean it, then reinsert and inspect oil.
2.
If the oil level reach to down limit sign (2), replenish the standard
oil to the level below upper limit sign(3), then
insert and screw down
the lid back.Check if it’s in good situation
Fig 12
Suggested engine oil number:
SAE-15W/40
3
2
Fig13
- 10 -
The free path of rear brake handle(Fig 14、Fig 15)
Measure the distance of rear brake pedal before detent function,
The free path should between 10-20mm, take the tail of brake handle as standard.
•
Adjust nut:
(A)increase the distance of free path.
(B)reduce the distance of free path
After adjust, the axle pin (2) should touch closely with nut (1) groove after adjust.
Fig14
Fig15
WARNING:
When the front disc gets worn to the limit (see the notice on the disc: MIN.TH.3mm),the
old disc must be changed in order not to influence the brake performance.
- 11 -
Abrasion mark of the brake(Fig 16)
(1)
Reference marks
(2)
Indicate marks.
If fully brake. Change the brake block when reference marks and indicate marks are
situated in a straight line.
Notice : Once maintenance for brake system is needed, find the nearest professional
repair department . Make sure the parts for replacement were made by our company.
Fig16
TYRE
check the tyre pressure regularly and adjust if necessary.
•
Check when the tyre cooled
•
Check if there is any metal trash or gravel in the groove of tyres
•
Check if any metal trash or gravel in the groove of tires.
•
Replace the tyre when it wears out to the abrasion mark.
ADMONITION:
•
If the tyre pressure dose not accord with the standard, it will possibly cause traffic
accidents.
•
It is dangerous to use a worn tire because the friction between tyre and road will be
affected which will possibly bring trouble to driving or even cause an accident.
- 12 -
Start engine (Fig 17)
•
Put the key into the key hole and turn to “ ”.
•
Electric starter: press start button (1) to start engine, don’t keep the start
button presssed more than 5 seconds each time.
NOTICE:
•
Electric starting is based on grasping the brake handle.
•
If electric starting doesn’t work, there must be a break for 30
seconds before you start the engine with it again
•
When start the engine in cold condition,
please warm
up engine for 3 minutes before running
•
The engine will be over heated if it works for a long
time at idle speed in an extremely hot day, you need to
power off the engine immediately.
- 13 -
Fig17
Drive motorcycle:
WARNING:
•
The temperature of exhaust pipe is much high during driving, you will be injured if
touching with it carelessly,
evn within little time after stopping, the tempreture can
also cause injury, so wear trousers to protect your legs against injury.
•
Wear helmet, glasses , and gloves when driving.
•
Loose or unsuitable clothes may cause an accident during driving
•
All the device must be installed according to requirement of the traffic rule.
•
Take the license with you when driving , each equipment of the motorcycle should
accord with the local traffic law.
NOTICE:
Control the speed and payload during the first 1000km.Payload lower than 75kg is
appropriate (including the weight of driver), overspeed or over loading will shorten the life
of engine, and change the crankcase oil after 300 km.
Control the speed according to blank 2
Log(km)
Speed (km/h)
0~200
200~500
≤20
≤30
Blank 2
500~1000
≤35
- 14 -
Driving operation
•
Release Main-Stand and sit on the saddle ,step on the ground by left foot to make
motorcycle plumb with floor.
•
Turn the throttle when Veh start, put your left leg back to footrest and control the throttle
to make the motorcycle reach good speed. close the accelerograph to slow down.
NOTICE:
•
Do not make a sudden speedup or speed-down with the throttle grip to prevent that
motorcycle rush out unexpectedly.
•
Driver must release the side stand before driving and try to know the status of
running road.
Brake operation:
1. Control the throttle grip
You must control the throttle grip and use both of the brake systems to slow down.
NOTICE:Drive with care when driving in bad situation like on moist or runny road, in a
rainy day. Do brake operation, speedup operation or turning operation carefully.
- 15 -
2. Front brake and rear brake work at the same time
Notice:When driving down on a cliffy brae, close the accelerograph entirely and use both of the brake
system to make the speed lower. Don’t do brake operation continuously to make it too hot, which will
affect the performance of brake.
Warning : When driving on a smooth or curving road at a high speed, don’t use only one
brake system, you must use both rear and front brake system at the same time to avoid an
accident.
Power off the engine(Fig 18、Fig 19)
• Close accelerograph: revolve to the end as the direction of the picture showing (commonly, the
engine will become in idle situation at the moment when you release the throttle grip)
• Turn the ignition switch to (
)
Fig19
Fig18
- 16 -
Parking operation:
When parking, tun the key to(
)position, put down the support and lock the handle well.
(See P7)
Admonition:Park the motor on a smooth ground, or it may fall down and cause injury.
Notice for anti-theft.
•
Lock the steering and do not leave key in the key hole before you leave.
•
Park the motor in a carbarn if possible.
•
Mount a alarm system for your motor.
- 17 -
Ⅳ、Maintenance and service
Maintenance periodic form
This maintenance is based on the odometer , See the Maintenance periodic form as an important
guide for your motor’s maintenance on schedule. You should increase the frequency of
maintenance if you use the motor at a high speed in a bad situation for a long time.Some main
parts of your motor should be inspected by a careerman after a repair for most parts or collision,
like Frame, hanger, or turning parts , Repare or replace broken parts to secure your safety.
Notice:For the safety and dependability , Never refit. Use the parts of us or parts of same
quality as ours for replacement. Otherwise, the performance and operation function will be
affected.
Warning: For the safety of personnel, no matter whaterve maintenance work carries on, fisrt
power off the engine , park the motor on a good ground and support the motor with stands
well.
Notice: the motor without use in winter or having been parking for longer than one month
needs maintenance before driving to check if the fuel , tyre or battery were bad or
corrupted.
- 18 -
Maintenance periodic form(blank 3)
Check before maintenance(See P9)
I:Check and adjust it when need.
C:Clean
R:Change
Blank3
Cyc
speedometer(×1000km)
Every month
Item
1
4
8
12
﹡
﹡
Fuel pipe
I
I
I
I
Throttle operation
I
I
I
I
﹡
﹡
﹡
﹡
﹡
﹡
Core of the air cleaner
*
cold system
Spark plug
Valve
Engine oil
Engine oil filter
The carburetor idling
(Note1)
(300km)R
I
R
I
C/1000km, if need:R
C/2000km, if need:R
I
I
- 19 -
I
15
23
27
I
(3000 km)R
When change oil:C If need R
I
I
I
I
Ref
page
25
25
24
Blank3 continue
Cyc
speedometer(×1000km)
Every month
Item
Rotate the belt
﹡
Gearbox
engine oil
﹡
Brake system
Brake cock
Head light
﹡
Hanging
system
﹡
The nuts\bolts
﹡
Wheel, tyre
*﹡
Turning
bearing
*﹡
(Note3)
(300km)R
(Note2)
1
4
8
12
C/1000km I, if need:R
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Ref
page
26
11
12
* Unless you are an expert on machine and hold a full set of tools and maintenance data, or leave
your motor to a mechanic person.to maintain or repair
** For safety, we claim all of items done by mechanic person.
Note:1、You’ d better shorten the period of maintenance if use the motor in a particularly moist or
dusty area, and when the fuel consumption becomes more and more, and accelerated effect is
bad, you should change some parts.
2、If you usually drive the motor in accidented roads, please go for a maintenance to protect the
performance of the vehicle .
3、change as the season changes in a cold area.
- 20 -
Solution for troubles(blank 4)
Blank4
Trouble
phenomenon
Spark
plug no
spark
The spark
is weak
Cann’t
start the
engine
No mixed
air in
cylinder
The cylinder
compresses
strength low
reason
Spark plug wear out
Ignition wire wear out
CDI wear out
Ignition switch wear out
Ignition come off or become
Spark plug gap too small or big
Spark plug pole burn
The spark plug accumulates
No spark to consult the spark
No fuel
Oil mouth stop up
solution
Change
Change
Change
Change
Connect well or firm and tight
Adjust
Change
Clear out
The oil passage stops up
Air cleaner stop up
Replenish
Dredge
Change
Dredge
Clean
Take in system leak
Check and clear out
Spark plug seat leak
Cylinder cover leak
Valve seat washer worn out
The piston-ring or the cylinder
The piston-ring is broken or stored
Screw up spark
Change spacer
Polish
Change them
Change piston-ring or clear
Fuel tank pressed the switch to
- 21 -
Trouble
phenomenon
The vehicle
has bad
accelerative
performance
The electric
start
does
not work
Riding
unsteady
the brake
does not
work
Trouble reason
The octane value of the fuel is too low
Oil path blocked
Ignition in wrong time
Spark too weak or flameout
Mixed air too dense or too thin
Air leak from the engine
Muffler blocked
Belt wear wear and tear
The automatic clutch roller wear and tear
See “ cann’t start the engine” as reference
The clutch is broken
the relay is broken
Battery electricity not enough
gap between turning bearings is too big
tyre pressure not enough
Front and rear axle released
The brake block wear and tear superlatively
brake cam wear and tear
Brake cable is broken
Free path too big
Blank 4 continue
solution
Change flue
Clean oil path
Check wire and change CDI
Check ignition and clear out
Clean adjust carburetor
Check and clear out
Dredge
Change
Change
Change
Change
Charge
Adjust
pump
Screw up nut
Change
Change
Change
Adjust
- 22 -
Clean the air filter(Fig20)
•
Take down the fixing bolt of air cleaner cover .
•
Take out the core from the air cleaner box.
•
Clean the filter element using compress air or dry brush
or put a new filter in the air clean box.
•
Do the above oppositely to reinstall the air filter.
NOTICE:
•
Never use gasoline or low burning point solvent to clean.
Fig20
Battery maintenance(Fig21)
It is adopted the airtight battery (don’t add water)
NOTICE:Never take apart upper cover of the electrolyte.
•
If you don’t use the motor for a long time. please take off the
battery and keep it in a ventilated and dry place
•
If the peg of battery is corroded. Please take it off and
clean.(use boiled water)
Fig21
NOTICE: Turn off the ignition switch before taking apart the battery. Taking negative terminal first
and positive terminal next, when installing, just opposite to above procedure.
- 23 -
Idle speed adjustment(Fig22、Fig23)
The carburetor has been adjusted to the best situation before selling out.
If it is not well adjusted, ask a professional person to adjust it as the following
instruction.
•
Warm up several minutes after engine starts
•
Screw the bolt 1 in slightly to increase the idle speed,
Fig22
then screw in the mix ratio screw first and next out from the idle
speed adjustment, screw to gain the minimum torque.
•
After adjusting the idle speed, adjust free path of the throttle to
2-4mm.
•
After adjusting, the engine speed can transit steadily when suddenly
apply the throttle instead of turning off.
Fig23
- 24 -
Change oil(Fig24)
l
Change oil only when the engine is not cooled yet and the vehicle is
supported by jiffy Stand, to pour out all the oil completely and quickly.
Clean the oil filter net
l Screw out the the cover of oil hole /oil dip rod and the cover of oil filter
screen,Take out oil hole cover and oil filter 1 then take strainer 2 and spring 3.
•
Clean the oil filter net using liquor
•
Fill in the oil filter net,spring and the cover of oil filter screen.
•
Inpour standard oil into the engine, not exceeding the upper mark,
•
When measuring the oil level, do not screw down the cover of oil hole / oil dip rod.
•
Fill in the cover of oil hole / oil dip rod.
•
Start engine and keep it working at idle speed for few
minutes, then turn it off.
•
Measure the oil volume of engine again to make sure it
does not leak.
- 25 -
Fig24
Change gear oil(Fig 25)
We suggest oil octane number:
SAE
80W/90(you can use antifreezing oil in very cold area)
Oil capacity
Changing capacity: 0.1L
•
Place the vehicle by the main stand.
•
Screw out the immersion bolt 1 and oil-drain bolt 2.
•
NOTICE : When draining the oil, the engine needs a certain
Fig25
temperature,
use the main stand to support the motor, make sure all the oil is drained.
•
Clean the drain bolt and then re-install it.
•
Inject oil into the hole of the immersion bolt slowly till the oil spill over.
•
Fix the immersion bolt and screw it tight.
- 26 -
Spark plug(Fig26)
1
Spark plug specification
Standard: C7HSA(NGK) or A7T、A7RT
•
(0.6~0.7)mm
2
Disconnect the joint of the spark plug cover and
take apart the spark plug with special spanner.
•
Check if there is any burnning ash or accumulated dirt on electrode or
porcelain head, if it singed badly, replace the spark plug, Clean the ash or
dirt with plug cleanser or a brush.
•
Normally the gap between side electrode (1) and
Fig26
Center electrode (2) is 0.6-0.7 mm.
•
Don’t use other kind of spark plug with different specification.
Fuse replacement
The rated electric current of the fuse is 15 A. If the fuse often burns down, it indicates the
short circuit or overload in the electric system. Ask the serviceman to repair it, and never
use the brass wires to replace the fuse.
- 27 -
V .Vehicle
Storage
STORAGE
If the vehicle hasn’t been used for a long time, some steps should be taken to prevent malfunction
and damage to the parts. Besides, before the long-time storage, proper repairs should also be done.
•
Change the engine oil.
•
Drain out the fuel in the fuel tank and oil in the carburetor.
Warning: Gasoline is inflammable and may cause fire and even explosion on certain conditions.
Therefore, no fire when draining.
u Take apart the spark plug, inject about 15~20ml oil into the cylinder, step down the kick
pedal several times and then fix the spark back on.
u
Take apart the battery and place it in a place without strong light or frozen ice, charge it every
month.
u
Clean the vehicle and wipe it dry, coat the wax on the surface of the paint, and anti-rust oil on
other metal parts.
u
Cover the vehicle and put it in a cool place.
Use the vehicle after long-time storage
•
•
Take off the cover and clean the vehicle. You should change the oil after 4 months above storage.
Charge the battery if necessary, and fix it on.Check all the parts before driving.(see p9), ride
motorcycle in a low speed in non-busy area, make sure the safety.
- 28 -
Ⅵ.
Vehicle identification.
Position of the model code, vehicle identification number and label(Fig 27)
Provide the numbers above when register to get the license ,do yearly inspection, and enjoy
the after-service .
the rivet for fixing name plate is on the right side of main stand.
Fig27
- 29 -
Ⅶ. Tool set
Toolbox(Fig28)is placed in the luggage box under the saddle, and toolbox
contains the following tools:
Wrench 8x10mm
Wrench 12×14mm
Screwdriver
Hexagonal wrench
Handle of screwdriver
Sleeve wrench 18.5×17mm
Fig28
- 30 -
Ⅷ. Main technique Parameter
Item
L×W×H (mm)
Wheel Base (mm)
Parameter
1860×705×1160
1340
Ground Clearance (mm)
140
Dry Weight
kg
94
Max Payload
kg
75
Turning Angle of Steering
Handle
º
V=40km/h
Max Speed km/h
Economic
Consumption
Climbing
Performance
Inclination
Start Model
Pressure Of Front Tire
kPa
Pressure Of Rear Tire
(kpa)
Transmission Type
m
≤21.78
≤50
Oil
Speed-down
2
average m/s
≥3.4
Rr Brake Distance
≤26.86
Engine type
Bore/stroke(mm)
≤2.3L/100km
≥4.5
-1.3%
Electric/Kick
Displacement(ml)
Battery
Oil capacity L
- 31 -
180
200
CVT
Speed
Ratio
Transmission
≤48
Fr Brake
Distance
Table5
Parameter
120/70-12
120/70-12
Item
Front Tire
Rear Tire
of
m
10.83~33.85
2
Speed-down average m/s
≥2.7
139QMB
Single/4stroke/air-cool
39.0×41.3
49.3
12V 7Ah
5
Add table5
Item
Lubricating Way
Rated Power r/min
Max Torque r/min
Parameter
Press and splash
2.2/7500
3.0/7500
Capacity of Crankcase
oil, L
Crankcase oil
Ignition way
Parameter
15 A
12V 18W/18W×2
12V 5W/21W
0.8
Fuse
Headlight
Tail Light/stop light
License Plate Light
Turning light
Fuel
Capacity
of
Gearbox oil, L
Gearbox Oil
SF SAE 15W/40
CDI
Clutch
Valve gap
Automatically centrifugal
0.03~0.05(cool)
Compression Ratio
10.5:1
Specification of Spark C7HSA(NGK)or A7TC、A7RTC
Plug
Spark Plug Gap mm
0.6~0.7
Idling Speed r/min
Item
(1500±150)
- 32 -
Ⅸ. Circuit Diagram
- 33 -
mm
12V 5W
12V 10W×4
RQ93 above
0.11
SAE 80W/90
Ⅹ.Emission
Control System Warranty Statement
Wangye USA Co., LLC is pleased to explain the emission control system warranty on
Highway Motorcycle. New Highway Motorcycle must be designed, built and equipped to
regulations and standards of the United States Environmental Protection Agency and the
California Air Resource Board and free from defects in material and workmanship that may
keep it from these requirements in the all applicable regulations.
Wangye USA Co., LLC must warrant the emission control system on the highway motorcycle
for 5 years or 6,000 km, whichever comes first, provided that there has been no abuse, neglect
or improper maintenance of highway motorcycle.
1. Period of Warranty
The period of warranty shall be one year on delivery, during this period of warranty:
(i). Any part defective by reason of the manufacturer’s faulty workmanship or material will
be replaced or repaired free of charge;
(ii). Any repairs or adjustments made necessary by reason of the manufacturer’s faulty
workmanship or material will be performed free of charge.
Emission control system may include parts such as the carburetor or fuel injection system,
the ignition system, catalytic converter and engine computer, if it is equipped. Also
included may be hoses, belts, connectors and other emission-related assemblies.
2. Responsibilities of Customer
To obtain repairs under warranty, the customer must:
(i). Ensure that the motorcycle is properly operated, maintained and stored as specified in the
- 34 -
Owner’s Manual;
(ii). Give notice to dealer approved by Wangye USA Co., LLC or other qualified service
facility of any and all apparent defects immediately upon discovery, and make the entire
motorcycle available at the time for inspection and repair at the dealer’s place of
business;
(iii). Provide proof of warranty coverage to dealer;
(iv). Authorize the dealer to tear down the motorcycle for diagnostic evaluation should it be
required.
All warranty repairs must be done by the dealer and final approval of any repairs rests with
Wangye USA Co., LLC. All parts replaced become the property of Wangye USA Co.,
LLC.
3. Exclusion
This warranty does not cover the repair or damage resulting from abuse or neglect of the
motorcycle. Examples of abuse and neglect include, but are not limited to:
(i). Racing and competition;
(ii). Use of lubricants, oils and fuel/oil mixture other than those recommender in the Owner’s
Manual, improperly installed accessories and use of parts or accessories that are not
equivalent in design and quality to genuine Wangye parts;
(iii). Damage as a result of accidents, collisions, contact with foreign materials, impact,
submersion or use of the motorcycle after discovery of a defect;
(iv). Appearance-related damages of body parts. Examples of such damages include but are
not limited to: scratches, dents, fading, flaking and peeling;
(v). Motorcycle which has been modified in any way from the standard specifications shown
in the Owner’s Manual, for example, the odometer has been altered;
(vi). Normal wear and tear, corrosion and routine maintenance, such as the recommended
- 35 -
service inspections;
(vii). Pre-delivery inspection and assembly;
(viii). Damage from theft, fire, vandalism, explosion, water or acts of God.
4. Restriction
This warranty is in addition to, and not a modification of, any legal warranty required by the
laws of any state of US.
Subject to any applicable sales or consumer legislation, the above warranty is in lieu of any
warranty or representation, express or implied, including any warranty of performance,
merchantability or fitness for a particular purpose on the part of Wangye USA, and any other
obligation or liability on behalf of Wangye USA, and the above warranty constitutes your
sole remedy and the full liability of Wangye USA. In no event shall Wangye USA be liable
for special, incidental or consequential damages howsoever caused, whether by negligence or
otherwise resulting directly or indirectly from the use of the Motorcycle, or the Motorcycle’s
having replacement parts or the unavailability of replacement parts. Wangye USA does not
assume or authorize any person to create or assume for Wangye USA any obligation or
liability in connection with the Motorcycle or any part thereof distributed by Wwangye USA.
5. Contact
For any questions regarding emission control system warranty, please contact as following:
Company Name: Wangye USA Co., LLC
Address: 1170 Corporate Dr. West Ste. 204, Arlington, TX 76006
Tel: 817-640-1108 ext 219
Fax: 817-649-5006
- 36 -