WangYe WY50QT-10 User manual

USER MANUAL
Motorcycle Operating Manual Model: WY50QT-7A
PREFACE
Thanks for your purchasing the motorcycle WY50QT-7A, and sincerely
welcome you to be our motorcycle user. To enjoy a more safe and
pleasurable driving, at first please familiarity with the manual must carry on
before driving. Your personal safety depends not only the vigilance and
familiar operation skills, but also relates to whether you are familiar with the
mechanical performance. Before driving, check-up and periodical
maintenance are basic requirement. If maintenance and repair needed, go to
our service center for help. If you know the mechanic knowledge and have
the tools, the dealer can offer you help with the maintenance and repair, like
providing the parts catalogue and the spare parts.
This manual explains in detail the correct operation and maintenance of
WY50QT-7A, together with the expectation for your long-time use.
Modifications in specification could cause the discrepancy with some figures
and content in the manual, we feel sorry for that and hold the final right of
interpretation.
Have a good enjoyment and thanks again for your purchasing!
IMPORTANT INFORMATION
Ÿ Driver and passenger
This motorcycle was only used to one driver. Never exceed to the Max load capacity of the motorcycle.
Ÿ For the safety, never drive to the motorcycle in the atrocious weather or the cold weather(under -12℃)
Ÿ For the road surface:
This kind of motorcycle is only drive in the highway.
Ÿ About the caution banner with the safety or environment, stick to the sundries box cover,
the rear shelf, and fuel tank cover. (Look at the clearly in the time for use or before use)
• Please carefully read the user manual
You must pay attention to the sentence or paragraph with caution banner.
Warning
No following the operation instruction in this manual may cause great damage to you.
Attention:
No following the operation instruction in this manual may cause injury to both you and vehicle.
Regard this manual as a permanent parts, even when transfer the vehicle to other
people; transfer the manual at the same time
LIST
Ⅰ. Motorcycle safety driving
Rules for safety driving ……………………1
Payload………………………………………2
Ⅱ.Parts & Subassemblies and use
instruction
Parts & subassemblies……………………3
Speedometer and indicator ………………5
Ignition switch………………………………5
Fuel meter …………………………………6
Starting button & stop switch ……………6
Starting switch………………………………6
Main beam switch…………………………7
Turning signal light switch…………………7
Horn switch…………………………………7
Steering handle lock………………………7
Seat lock……………………………………8
Ⅲ.Operation guide
Checking before driving……………………9
Engine Starting……………………………14
Driving motorcycle…………………………15
Driving operation…………………………16
Braking operation………………………16
Engine power off operation……………17
Stopping motorcycle …………………17
Ⅳ.Service and maintenance
Periodic maintenance schedule……………18
Simple trouble solution……………………21
Cleaning air filter ………………………23
Battery maintenance………………………23
Adjusting idling speed……………………24
Replacing gearbox oil………………………25
Spark plug…………………………………26
Replacing fuse ……………………………26
Ⅴ.Vehicle storage………………………27
Ⅵ.Vehicle identification ………………28
Ⅶ.Tool set ……………………………28
Ⅷ. Main techneque Parameter ……29
IX. Circuit diagram………………………31
Ⅹ.Emission Control System Warranty Statement…32
Ⅰ. Motorcycle safety driving
Rules for safety driving
Only Driver can insure the motorcycle driving safety
1.The motorcycle happen the many accidents, all reasons are that the car drivers didn’t
look at the motorcycle drivers. So the motorcycle drivers must:
l Put up the coat in bright color
l Avoid to the driving at night .you must drive on guard and carefully to the strong
light.
2.Particular care should be exercised at the level crossing of roads, entrance and exit of
parking lot or on the automobile lane.
3. Don’t speeding, because the speeding usually to happen an accident.
4. You must get to the driving license and familiar with motorcycle. Never lend motorcycle
to the man without driving license or unfamiliar with motorcycle.
5. Avoid driving the road with accidental, easily result the operation failure or the part was
broken.
6. Always do a pre-riding inspection before operating the vehicle.(Ref P9)
7. During drive, grasp the handle and feet on the footrest.
-1-
Payload
l Warning :
The light goods can only put in the rear shelf or other deposited place.
The goods payload not heavier than Chart 1:
Deposited
Weight (kg)
Rear shelf
Chart 1
5
※ The motorcycle max payload is 75kg,including the weight with the driver,
the passenger and the goods.
※ If the motorcycle is over loading, it can affect the motorcycle stability and
operation.
※ The goods on the motorcycle must fasten.
-2-
Ⅱ.Parts & Subassemblies
Parts & Subassemblies
(Fig1.Fig2)
Fig 1
-3-
Dashed(……)Indicate the not see parts directly
- 4 Fig
- 2
Speedometer and indicator (Fig3-1 or FIG3-2)
⑴Fuel Meter
⑵Turning signal light LH
⑶EngineTachometer
⑷Turning signal light RH
⑸Speedometer
⑹Odometer
⑺main beam indicator
⑻Oil indicator light
Note: Machine Meter is available(See fig3-1)
Fig 3-1
Fig 3-2
Ignition Switch(Fig4)
⑴On (
)—when the switch turn to this position,
Start engine and do not pull out the key.
⑵Off (
)—When the switch turn to this position,
Engine power off and take out the key.
⑶Lock (
)—When the switch turns to lock position ( ),
Take out the key .do not do any turning operation
And do not start engine and turn on light.。
Notice :If the engine is idling speed for a long time in the hot climate,
It will appear too hot Phenomenon Must close engine.
Fig 4
-5-
Fuel Meter(Fig 5)
1.Fuel Meter (Fig 5) shows the approx remainder of fuel.
When the finger to (F), it indicates Full tank of 6L.
2. When the finger at red section it indicates the remainder of
flue is 1.8L
Starting Button (2)and stop Switch(1)(Fig 6)
(1) Turn this button to
Fig 5
for starting engine.
(2)Press (2) this button,starting motor will start the engine.(Ref P11)
(3)Stop engine, turn the button to “
” .
Fig 6
-6-
Main beam switch (1)(Fig 7)
Press“
”button,is main beam;Press“
”button isdipped beam。
Turning signal light switch (2)(Fig 7)
When the switches on ( ) ,the left turning signal light turn on.
When the switch on ( ), the right turning signal light turn on,
Press it down the light turn off.
Horn Switch 3(Fig 7)
Fig 7
Press this button, the horn makes sound.
Steering handle lock(Fig8, Fig9)
Turn the steering handle left to end, presses down ignition key1 to ( ), the steering handle are
locked .Do the above opposite it opened.
Fig 8
-7-
Fig 9
Seat Lock(Fig 10)
• Put the key into seat lock hole and then clock-wise
open the lock.
• Press down the multi-purpose until it make sound of
locked, then push the back of multi-purpose to confirm
it has been locked and take out the key.
Fig 10
-8-
Ⅲ. Operation instruction
Checking before driving
For safety and prevent trouble or accident,
Pre-check up is necessary.
Fuel
When the pointer or fuel meter is close to red section, replenish oil;
meanwhile, check the Fuel Tank and Carburetor rack or not.
Fuel Tank:6L
•
•
•
Clock –wise to open the tank cover.(Fig 11)
Suggestion gasoline: octane number is 90
Do not replenish oil together with tidy or water
Fig 11
Fig 11
NOTICE:
If check gasoline orreplenish gasoline soon after stop, Beware of
burning.
Keep gasoline level under away from the height panel of flue tank while
replenishing.
If gasoline level is too high, it is easy to leak out.
If swallow the oil careless, see the doctor at once.
-9-
checking engine oil
checking engine oil level(Fig 12、Fig 13)
1.Keep the motor steady in the flat ground, and then use the
key to open the seat cover.
2.Open the cap of engine oil tank, Check the oil volume,oil
Fig 12
capacity: 1.2L
Suggestion the engine oil:
special 2T oil(FC level)
Fig 13
- 10 -
Free Path of Rear Brake( Drum Brake)(Fig 14,Fig15)
Measure the distance of rear brake pedal before detent function .the free path should
between 10-20mm, take the tail of brake handle as standard.
•
Adjust Nut:
(A)Reduce Free Path。
(B)Increase Free Path
When adjust, the Pin 2 and Adjust Nut1 should impinge on
Note: Rear Disk brake is available, but can’t adjust Free Path. When you can’t see Disk brake oil, please
immit the disk brake oil. (Fig16, Fig17)
Fig 14
Fig 15
Fig 16
Fig 17
- 11 -
Brake wear and tear indicator sign(Fig 18)
(1)
Reference Mark
(2)
Arrow indicator sign
If the brake brakes absolutely, Arrow indicator sign and Reference be in line, must change the brake
shoe.
Note: If need maintain the brake, should find the nearest service department to operate.
There is professional technician in the service department to maintain. When you replace the
parts, should use the real original parts.
1
2
Fig18
- 12 -
Tire
Check the tire pressure regularly and adjust.
•
Check before the tire cooled
•
Check if there any metal trash or gravel in the groove of tires
•
Inspect whether there is nick, embed nail or other tartness object on the tread or not. Inspect
whether there is impress, dent or distortion for rim or not. If find any damaged, should invite
service department to inspect for you.
•
When the tire pattern wear and tear to the wear sign, must change the new tire.
WARNING:
•
If the tire pressure dose not accord with the standard, it will properly cause the traffic
accident. If the tire pressure is too low, the tire will fetch away or take of rim.
Ÿ
It is dangerous that use the worn tire; It will have effect to friction between tire and rode.
Maybe difficult to drive or accident.
- 13 -
Starting engine (Fig 19)
•
Preparative before starting:Set up the Main Stand,
Put the key into ignition switch and turn to “ .
•
Electric starter:Press start button (1) to start engine, DO not
use the starter more than 5 seconds each time.
NOTICE:
Electric starting is only in the condition of grasping the brake handle.
Fig19
Electric starting not succeed, if starting again with it, we must stop for 30 seconds, If still
can’t start, Please use kick-start.
Engine kick-start :open ignition switch and add gasoline slowly, step kick-starter pedal
down quickly with strength to start engine.
Notice: After using kick-starter pedal, pull it back to original position. Otherwise
have effect to safety ride, and bad to engine.
Had better not open ignition switch when scooter has not use for a long time, and first
step kick starter for some times. Make flue into carburetor and then into cylinder, and
open ignition switch, Start engine, it is easy to start engine like this.
If cold start warm up engine for 3 minutes.
- 14 -
Driving motorcycle:
WARNING:
Wear the trousers to avoid touching with exhaust pipe and was burnt.
The entire device must be installed according to requirement of the traffic rule.
•
Take the license to riding.
NOTICE:
Control the speed and load during 1000km of running in period. Load should
be within 75kg(including driver) If take more weight and speed will reduce life
of engine.
Speed as per Chart 2:
Chart 2
Leg(km)
0~200
200~500
500~1000
Speed (km/h)
≤20
≤30
≤35
- 15 -
driving operation
•
Take back main stand and sit on the seat, Left foot step on the ground make the vehicle and
ground upright.
•
Release rear brake level, accelerate slowly with throttle grip, then motorcycle will move
forward smoothly. Decelerate gradually when you stop.
WARNING
• Don’t operate the throttle ON-OFF suddenly, Otherwise, the motorcycle will run out, Maybe
lose control.
• Before drive, must take the stand
Brake operation:
1.Control throttle grip
If want to reduce speed, Must control the throttle grip, at that time use the two-brake
system, this point is very important.
Notice: if the drive will be done in this situation, for example: damp or loosely roads,
raining .no matter brake, accelerate or turn must take care.
2. Operate front and rear brake
Notice: Must totally close the flue when drive in a descent, and use two-brake
system for reduce speed. Don’t use brake continuously, other wise it will reduce
the effect of brake because of too hot.
Warning: Don’t use single brake when drive with high speed, special crooked and
- 16 -
slippery road. Must use two-brake system for avoiding accident.
Engine power off operation (Fig 20, Fig 21)
Turn off Throttle:Revolve to the lowest place according to picture. (Normal situation is
loose the throttle grip, and the engine is idling speed)
• Put the key to “
”.
Fig 20
Stopping operation:
Fig 21
When the motorcycle stop, put the key to “ ” position .put down stand and lock handle.(Ref P7)
Warning:Motorcycle should be park on the Solidity and Flat ground, otherwise, it
maybe make some body injured or vehicle down .
Alarm points:
1 Locking the handle and do not left key in the switch
2 Put the motor into the garage
3 Use the excellent guard against theft device。
- 17 -
Ⅳ.Service and maintenance
Maintenance periodic Schedule
The maintenance is important to motorcycle, If drive with high speed in bad situation for
a long time, must add the times of maintenance, If motorcycle have a big repaired or a
accident, Must take it to check for mainly spare parts. For example: frame, indicator
parts and so on. Repair or change the worn parts. Make sure safety.
Notice: Don’t change motorcycle make sure it’s safety, Must use good quality spare
parts if replace spare parts .if use bad quality spare parts, it will influence the safety of
motorcycle.
Warning: Must close engine when make maintenance .it make sure the repairer’s
safety. And put down the stand on the smooth ground.
Notice: Must make a good maintenance if the motorcycle don’t use over a month, or
don’t use in all the winter. Make sure fuel, tire and battery avoiding corroding
- 18 -
Periodic Maintenance Chart(Chart 3)
When you will make the Periodic Maintenance, you should inspect before driving.(Ref P9)
I:Inspect and adjust when necessary
C:Clean
R:Replace
Chart 3
Cycle
1
Item
Every Month
﹡
﹡
﹡
﹡
﹡
Fuel Pipe
I
I
Throttle operation
Air filter element
(Note 1)
Spark Plug
Idling speed
I
Speedometer(×1000km)
4
8
12
6
12
18
I
I
I
I
I
I
C/1000km, if need: R
C/2000km,If need: R
I
I
I
Ref
Page
16
23
26
24
Chart 3
- 19 -
Cycle
1
Item
Every month
﹡
﹡
﹡
﹡
﹡
﹡
﹡
Transmission
Gearbox oil
Brake system
Brake Switch
Headlamp
Suspension
Bolts Nuts tighten
(Note 3) (300km)R
(Note2)
Wheel, Tyre
Turning bearing
Speedometer(×1000km)
4
8
12
Ref
Page
6
12
18
Per 1000km I, If need: R
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
25
11
13
*If you have all of tool and maintenance document, you are a mechanic person, or else
must let special person maintenance and repair.
*For safety, we claim all of items have done by mechanic person.
Note: 1.Iif this area is very damp or have a lot of dirty .you had better make a short time
for maintenance, when it take more oil quantity or not strength, it must change.
2. If it was used every day, must make maintenance.
3. According to season to change in a cold area.
- 20 -
Simple trouble solution
Complaint
Chart 4
Symptom and possible causes
Plug not
sparking
Engine
does not
start
Spark
plug is
weak
No mixed
air in
cylinder
Cylinder
compresses
strength low
solution
Damaged spark plug
Damaged Ignition Coil
Defective CDI
Defective ignition switch
Renegade or loosely Ignition system
Replace
Replace
Replace
Replace
Spark plug gap too small or big
Spark plug pole burn
Adjust
Replace
Spark plug accumulates carbons
Clear out
Fuel use out
Replenish
Oil mouth stop up
Dredge
Fuel tank switch wear
Change
Fuel path stop up
Dredge
Air filter stop up
Clean the air filter element
Intake system leak
Check and clear out
Spark plug seat leak
Cylinder cover leak
Tighten spark plug
Change washer
Piston ring & cylinder wear badly
Change piston or cylinder
Piston ring break/ unused Carbon block
Change piston ring / clear out carbons
Connect well or tighten
Chart 4
- 21 -
Complaint
The vehicle
is unable to
accelerate
performance
badly
Symptom and possible causes
Change fuel
Oil path stop up
Clean oil path
Ignition time is too early or too late
Check coil and change CDI
Spark too weak or flameout
Check ignition and clear out
Mixed air too dense or race
Clean& adjust carburetor
Engine leak
Check and clear out
Muffler stop up
Dredge
Belt wear
Replace
Replace
Replace
Replace
Automatic clutch roller wearing
Electric
start failure
Clutch worn
Starting relay worn
Turning bearing gap too wide
Charge
Adjust
Lack of tire pressure
Pump
Front& rear Axle flexible
Tighten nut
Replace
Replace
Replace
Electric quantity lack
Driving
unsteady
Brake
Failure
solution
Octane value of the fuel is too low
Brake pad fray to limit
Brake cam fray
Brake cable damaged
Free path overlong
Adjust
- 22 -
Cleaning Air Filter(Fig 22)
• Take apart the bolt of air filter cover.
• Take out filter element
• Compress air or use dry brush to clean filter
element.。
• Do the above opposite to reinstall the air filter.
NOTICE:
Fig 22
• Do not use gasoline or low burning point solvent to clean paper filter element.
Battery maintenance(Fig 23)
It is Adopted the airtight battery (don’t add water)
Notice: Do not take apart the airtight
• If the motorcycle have not been used for a long time.
Taking off the battery and putting it into a dry and place.
• The head of battery was corroded, please take it off and
clean. (Can use boil water)
Fig23
NOTICE: turn off the ignition switch, take apart negative pole ○
+ when you are installing.
first, but install positive pole ○
- 23 -
Adjusting idling speed(Fig 24, Fig 25)
The carburetor is in the best situation before sale, if the carburetor is still
influence riding. Please adjust it under the instruction of professional man.
• Warm up few minutes before start。
• adjust Idle screw (1) to improve idle speed slightly to enter to
fasten, Withdraw it than screw slowly after stocking to fasten
to mix and then rapidly, to stabilizing the position at most,
then withdraw slowly, get and stabilize the position the most
low.
• After adjust idle, then adjust accelerograph handle to
free path for 2-4mm,then use adjustor (2) to adjust, screw
down nuts, and then screw up it after adjust.
• Adjusting the idle speed, it should be able to suddenly
strengthen the throttle, the rotational speed of the engine
should be excessively steady, no temper and flameout, stop
working or arrange organ not to flameout at being last throttle.
Fig24
Fig25
- 24 -
Replacing gearbox oil(Fig 26)
Suggestion gearbox oil :
SAE 80W/90(North Cold Area use anti-freezing oil)
Oil container
Resolving capacity:0.11L
Replacing capacity :0.09L
1
•
Make the motorcycle on the Stand
•
Take apart the immiting bolt (2), and the spilling bolt (1).
NOTICE: The engine must be warmer when
2
spilling and the vehicle must be steady by main
1
Fig26
stand. Make sure the Engine is empty
•
Reinstall the spilling bolt after clean. And screw up.
•
Inject 100ml to engine through immit bolt
•
Install immit bolt and screw up.
- 25 -
SPARK PLUG(Fig 27)
Specification of Spark Plug: BPR7HS ,BP7HS (NGK), E7TC , E7RTC
• Disconnect the spark plug cap, and then use the special handle to remove Spark plug.
• Check if the spark plug electrodes and the center porcelain
1
head burned, accumulative carbon, etc. If the spark plug
(0.6~0.7)mm
2
is burned out, replace new spark plug
Use spark plug cleaner to clean the deposits, or use a wire brush.
Adjust the Spark Plug gap between(0.6~0.7)mm.
• Don’t use an unspecified spark plug.
Fig 27
Replacing fuse
The specified electric current of the total fuse is 15 A, which is in Battery.
If the connection is not good, the fuse will overheat and breakdown.
Do not use brass wires to replace the recommended.
- 26 -
Ⅴ.Vehicle storage
Storage
For store up the motorcycle for a long period of time, for example, in wintertime, some steps
should be taken to prevent malfunction of and damage to its components, which might be caused
by long storage. Besides, before the long storage, proper maintenance has to be carried out for
fear that it might be forgotten when vehicle is put back into use after storage.
1. Change engine oil.
2. Drain off fuel from the fuel tank and carburetor.
Warning: Gasoline is inflammable and may cause fire and even explosion under certain conditions.
Therefore, do not smoke, make fire or have any fire left behind on draining off fuel.
3. Take out the spark plug, pour about 15~20ml clean engine oil into the cylinder, step down the
kick lever repetitively for several times so as to have machine oil distributed all over the
engine and finally fit the spark back on.
4. Wash the motor, wipe it dry and apply an even coat of wax to the painted surface. Chromate
treatment can prevent the surfaces from rusting.
5. Inflate the tires as required and pad the vehicle up by wooden blocks with the two wheels
clearance of the ground.
6. Put the vehicle in a shady and cool place free from humidity and direct sunshine and cover it
properly (but not with plastic or other painted materials).
Reuse motorcycle.
Take down the motorcycle cover and clean the motorcycle, if the storage time exceeds 4 months,
Must change engine oil.
Must charging if need, and then install battery.
Must check all of terms before drive (Page 9), for the safety must try the motorcycle with lower
speed for some time in a not busy rode.
- 27 -
Ⅵ.Vehicle identification
Vehicle type, Code and trademark of the bikes(Fig28)
When the bikes are registered or getting the license from the transport department, the
owner should be send the VIN number and engine number。The maintain people
change the parts, need the numbers too.
The products brand should be added at the right side plate of the Main stand(see P3).
Fig 28
Ⅶ.Tool set
Tool bag(Fig 29)in the boot of seat, Using for the urgent accident
when driving, it including the something of the following:
8×10mm spanner
Screw drive
Wrench bar
12×14mm spanner
Hexagon spanner
18.5×17mm wrench spanner
4
- 28 -
1
Fig 29
Ⅷ.MAIN PARAMETER
Item
Parameter
Chart 5
Parameter
Item
L×W×H mm
Wheelbase mm
Ground Clearance mm
Dry weight kg
Max Load kg
1983×683×1110
1380
130
95
75
Front tyre
Rear tyre
Air Pressure, Fr tyre
Air Pressure, Rr tyre
Transmission system
120/70-12
120/70-12
150kPa
200kPa
Turning angle of steering
handle
≤48°
Ratio
10.83-33.85
Brake Distance m
≤4(20km/h)
Engine Type
1PE40QMB, Air-cooled,
stroke, Single Cylinder
Max Speed km/h
Consumption L/100km
Climb ability
º
Light vertical angle
Starting system
≤55km/h
≤2.0L/100km
≥4.5
-1.3%
Electric &Kick
Bore×stroke
Displacement
Clutch
Fuel tank
Battery
mm
ml
CVT
40.0×39.2
49.3
Automatically, centrifugal
L
6
12V 7Ah
- 29 -
Chart 5
Item
Lubricate System
Rated Power
Max Torque
Compression ratio
Parameter
Separate lubricative
3.0kW/7000(r/min)
3.9N.m/6500(r/min)
7:1
License light
15 A
12V 35W/35W×2
12V 21W/5W
12V 5W
Spark Plug Model
BPR7HS, BP7HS(NGK)、
E7T or E7RTC
Direction light
12V 10W×4
Spark plug gap mm
mm
Idling speed
r/min
Engine Oil
Capacity of engine oil
0.6~0.7
(1800±180)r/min
Special 2T (FC Lever)
1.2L
Fuel
Ignition System
Gearbox oil
Capacity of gearbox oil
RQ90 above
CDI
SAE 80W/90
0.1L
- 30 -
Item
Fuse
Headlamp
Tail/stop light
Parameter
2
IX. Circuit diagram
- 31 -
Ⅹ.Emission Control System Warranty Statement
Wangye USA Co., LLC is pleased to explain the emission control system warranty on
Highway Motorcycle. New Highway Motorcycle must be designed, built and equipped to
regulations and standards of the United States Environmental Protection Agency and the
California Air Resource Board and free from defects in material and workmanship that may
keep it from these requirements in the all applicable regulations.
Wangye USA Co., LLC must warrant the emission control system on the highway motorcycle
for 5 years or 6,000 km, whichever comes first, provided that there has been no abuse, neglect
or improper maintenance of highway motorcycle.
1. Period of Warranty
The period of warranty shall be one year on delivery, during this period of warranty:
(i). Any part defective by reason of the manufacturer’s faulty workmanship or material will be
replaced or repaired free of charge;
(ii). Any repairs or adjustments made necessary by reason of the manufacturer’s faulty
workmanship or material will be performed free of charge.
Emission control system may include parts such as the carburetor or fuel injection system, the
ignition system, catalytic converter and engine computer, if it is equipped. Also included may
be hoses, belts, connectors and other emission-related assemblies.
2. Responsibilities of Customer
To obtain repairs under warranty, the customer must:
(i). Ensure that the motorcycle is properly operated, maintained and stored as specified in the
- 32 -
Owner’s Manual;
(ii). Give notice to dealer approved by Wangye USA Co., LLC or other qualified service facility
of any and all apparent defects immediately upon discovery, and make the entire
motorcycle available at the time for inspection and repair at the dealer’s place of business;
(iii). Provide proof of warranty coverage to dealer;
(iv). Authorize the dealer to tear down the motorcycle for diagnostic evaluation should it be
required.
All warranty repairs must be done by the dealer and final approval of any repairs rests with
Wangye USA Co., LLC. All parts replaced become the property of Wangye USA Co., LLC.
3. Exclusion
This warranty does not cover the repair or damage resulting from abuse or neglect of the
motorcycle. Examples of abuse and neglect include, but are not limited to:
(i). Racing and competition;
(ii). Use of lubricants, oils and fuel/oil mixture other than those recommender in the Owner’s
Manual, improperly installed accessories and use of parts or accessories that are not
equivalent in design and quality to genuine Wangye parts;
(iii). Damage as a result of accidents, collisions, contact with foreign materials, impact,
submersion or use of the motorcycle after discovery of a defect;
(iv). Appearance-related damages of body parts. Examples of such damages include but are not
limited to: scratches, dents, fading, flaking and peeling;
(v). Motorcycle which has been modified in any way from the standard specifications shown in
the Owner’s Manual, for example, the odometer has been altered;
(vi). Normal wear and tear, corrosion and routine maintenance, such as the recommended
service inspections;
(vii). Pre-delivery inspection and assembly;
- 33 -
(viii). Damage from theft, fire, vandalism, explosion, water or acts of God.
4. Restriction
This warranty is in addition to, and not a modification of, any legal warranty required by the
laws of any state of US.
Subject to any applicable sales or consumer legislation, the above warranty is in lieu of any
warranty or representation, express or implied, including any warranty of performance,
merchantability or fitness for a particular purpose on the part of Wangye USA, and any other
obligation or liability on behalf of Wangye USA, and the above warranty constitutes your sole
remedy and the full liability of Wangye USA. In no event shall Wangye USA be liable for
special, incidental or consequential damages howsoever caused, whether by negligence or
otherwise resulting directly or indirectly from the use of the Motorcycle, or the Motorcycle’s
having replacement parts or the unavailability of replacement parts. Wangye USA does not
assume or authorize any person to create or assume for Wangye USA any obligation or liability
in connection with the Motorcycle or any part thereof distributed by Wangye USA.
5. Contact
For any questions regarding emission control system warranty, please contact as following:
Company Name: Wangye USA Co., LLC
Address: 1170 Corporate Dr. West Ste. 204, Arlington, TX 76006
Tel: 817-640-1108 ext 219
Fax: 817-649-5006
- 34 -