NEW DEALER SET-UP
MARINE NEW DEALER SET UP TOOL SURVEY
SPECIFIC TOOLS
TOOL DESCRIPTION
APPLICATION
68F-85300-01-00
YB-06052
YB-06265
YB-06440-A
YB-06757
YB-06766
YB-06767
YB-06768
YB-06769
YB-06770
YB-06775
YB-06787
YB-06788
YB-06790
YB-06791
YB-06792
YB-06793
YB-06795
YB-34432-D
YB-34446
YB-34468-A
YB-38831/YB-06771
YB-38832/YB-06772
YB-44241
YB-44478
YB-45544
YU-39991
YDIS Yamaha Diagnostic System . . . . . . . . . . . . . . . . . HPDI/F115/F200/F225
Shift Rod Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40hp ~ 3.1L
Backlash Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All
Forward Gear Shim Gauge . . . . . . . . . . . . . . . . . . . . . . LF200/225
TPS Test Harness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6L ~3.1L
Fuel Pressure Gauge. . . . . . . . . . . . . . . . . . . . . . . . . . . . OX66/HPDI/F115
Ignition Coil Test Lead. . . . . . . . . . . . . . . . . . . . . . . . . . OX66/HPDI
Air Temperature Sensor Test Lead . . . . . . . . . . . . . . . . OX66/HPDI
Air Pressure Sensor Test Lead . . . . . . . . . . . . . . . . . . . OX66/HPDI
Lighting Coil Test Lead . . . . . . . . . . . . . . . . . . . . . . . . . OX66
CDI Tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OX66
Lighting Coil Test Lead . . . . . . . . . . . . . . . . . . . . . . . . . HPDI
Isolator Wire Test Lead . . . . . . . . . . . . . . . . . . . . . . . . . HPDI
Regulator/Rectifier Test Harness . . . . . . . . . . . . . . . . . F115
Pulsar Coil Test Harness . . . . . . . . . . . . . . . . . . . . . . . . F115
CDI Tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F115
TPS Test Harness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F115
Indicator Light Test Lead (YB-06444 & YB-06794). . . All V6
Pinion Gear Shim Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . 3cyl ~ 3.1 L
Forward Gear Shim Kit . . . . . . . . . . . . . . . . . . . . . . . . . 3cyl ~ 3.1 L
Reverse Gear Shim Kit . . . . . . . . . . . . . . . . . . . . . . . . . . 3cyl ~ 3.1 L
Charge Coil Test Harness . . . . . . . . . . . . . . . . . . . . . . . V6
Pulsar Coil Test Harness . . . . . . . . . . . . . . . . . . . . . . . . V6
Valve Depressor Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . F80/100/115
O2 Sensor Wrench. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All OX66/HPDI
Cylinder Leakdown/Compression Tester . . . . . . . . . All 4-Stroke/2-Stroke
Peak Voltage Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . All
1
TABLE OF CONTENTS
General Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
1&2 Cylinder 2-Stroke
Power Head Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lower Unit Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
1&2 Cylinder 4-Stroke
Power Head Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Lower Unit Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
Power Trim & Tilt/Midsection Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3 Cylinder 2-Stroke
Power Head Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lower Unit Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-27
Power Trim & Tilt/Midsection Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3 Cylinder 4-Stroke
Power Head Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Lower Unit Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-32
Power Trim & Tilt/Midsection Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4 & 6 Cylinder 2-Stroke
Power Head Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-37
Lower Unit Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-45
Power Trim & Tilt/Midsection Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-46
4 & 6 Cylinder 4-Stroke
Power Head Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-51
Lower Unit Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-58
Power Trim & Tilt/Midsection Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-59
Watercraft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-66
Shop Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68-87
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88-89
Policies & Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90-91
Order Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
2
G
General Tools
GENERAL TOOLS
GENERAL TOOLS
Part#
Description/Use
Application
YB-06071
Driver Handle (Large)
All Engines
This heavy-duty handle is used with the appropriate
adapters to remove and install seals and bearings.
YB-06229
Driver Handle (Small)
All Engines
This tool is used in many applications with the appropriate
adaptors to remove and install seals and bearings.
YB-07003
Backlash Adjustment Plate
All Engines
This universal plate bolts to the lower unit and will accept
most magnetic dial indicator bases for accurate lower
unit backlash checks.
YM-01253
Valve Spring Compressor
All 4-Strokes
This compresses the valve springs for valve removal. There
are various adaptors for the different models. Use the
appropriate adaptor.
YB-06265
Backlash Indicator Rod
All Engines
This rod clamps onto the driveshaft to check backlash. Use it
with Backlash Plate YB-07003 which will accept a Magnetic
Dial Indicator Base YU-34481.
YB-06139
Flywheel Magneto Holder
All
This tool holds the flywheel magneto for tightening and
loosening of the flywheel nut.
YB-06181
Universal PTT Pressure Gauge
This gauge measures the operating fluid pressure of the
power trim and tilt system.
4
Most
Units
GENERAL TOOLS
Description/Use
Application
YB-34465
Transom Drill Fixture
40 ~ Up
This tool makes drilling of outboard transom mounting holes
quick, accurate and easy. Fixture consists of a steel plate with
drill bushings positioned in the correct location, centerline
location windows and built-in transom height stop.
YB-91044
Neway Valve Seat Kit
This valve seat reconditioning kit is specifically designed for
4-strokes outboards. Contains the necessary cutters and
guides. Photo not shown.
YB-45544
Cylinder Leakdown/Compression Gauge Kit
This multi-use kit was designed specifically for the Yamaha
outboard. The 4-strokes require an extender reach to
properly mount in the spark plug hole.
YB-34446
Forward Gear Shim Selecting Tool
All
4-Strokes
GENERAL TOOLS
Part#
All
2&4
Strokes
40 ~ Up
To determine the correct forward gear shim, it is necessary to
accurately measure the forward gear bearing height. This tool
gives the technician a means of loading the bearing to
manufacturer specifications to determine the shim size.
Includes: YB-34446-1 Base Plate, YB-34446-3 Compression
Spring, YB-34446-4 No. 1 Press Plate, YB-34446-5 No. 2
Press Plate, YB-34446-6 Gauge Pin, YB-34446-7 Gauge Pin,
YB-34446-8 Gauge Pin, YB-34446-11 Instruction Card, Hex
Nut 500-13 UNC-28 1.06 o.d. x .53 i.d. x .09 thick.
YB-34432-D
Pinion Shim Selecting Tool
40 ~ Up
This tool allows the technician to determine the exact pinion
gear shim size with a minimum of lower unit overhaul.
Includes:
YB-34432-6 Gauge Block, YB-34432-7 Gauge Block,
YB-34432-8 Gauge Block, YB-34432-9 Gauge Block,
YB-34432-10 Adapter Plate, YB-34432-11A Gauge Base,
YB-34432-19 Gauge Block, YB-34432-20 Gauge Block,
YB-34432-12 Instruction Sheet, Hex Head Cap Screw
M8 x 1.25-6g x 20mm Long (4).
YB-39952
PTT Main Valve Leak Tester
This tester checks for leaks with the power tilt and trim main
valve seat.
Most
Models
5
GENERAL TOOLS
GENERAL TOOLS
Part#
Description/Use
Application
YB37103
Terminal Kit
All
This kit is specifically designed for marine use with tin-plated
connectors and sealed insulators. This kit is invaluable
for rigging Yamaha components.
A
C
E
F
G
H
I
J
B
D
YB-37103-3
YB-37103-4
YB-37103-5
YB-37103-6
YB-37103-8
YB-37103-9
YB-37103-10
YB-37103-11
YB-37103-12
YB-37103-13
YU-05212
Replacement Connectors
Bullet Plug
Qty.50
Bullet Socket
Qty 50
Eye Connector
Qty.50
Eye Connector
Qty.50
Bullet Plug
Qty.50
Bullet Socket
Qty.50
Bullet Socket
Qty.50
W-socket
Qty.50
W-socket
Qty.50
Eye Connector
Qty.50
Crimper Photo not shown.
YU-34898
High Current Shunt
A
B
C
D
E
F
G
H
I
J
All
The High Current Shunt is a calibrated resistance wire which
is connected in series with the electrical accessory to be tested
and plugged into a digital multimeter. The multimeter
provides a direct readout of current draw from 0-99 amps
(100-199 amps momentary), in 0.1 amp increments.
Photo not shown.
YU-03097
Dial Indicator Gauge 0-5mm
All
The Dial Indicator Gauge is used for measuring lower unit
backlash. It is to be used with Adaptor Plate YB-07003 and
Magnetic Base YU-34481.
YB-06029-4
Pinion Gear Bushing Installer
All
This tool is used to install the pinion gear bushing up into
the driveshaft housing. It may require additional adaptors
depending on the model engine.
YU-39991
Peak Voltage Adapter
The Peak Voltage Adaptor is used with most multi-function
DVA motors. It is used with various adaptors to measure
voltage readings on an outboard electrical system.
6
All
1
1& 2 Cylinder 2-sTroke
POWER HEAD & LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06104
Connecting Rod Small End Bearing Installer
9, 9, 15
1&2 CYLINDER 2-STROKE
This tool installs the small end needle bearings into the
connecting rod.
LOWER UNIT TOOLS
YB-06014
Bearing Installer Forward Gear Bearing
2, 4, 5
It installs the forward gear bearing and the driveshaft oil
seals. It is used with Driver Handle YB-06229.
YB-06025
Driveshaft Bearing Installer
2, 4, 5
It installs the driveshaft needle bearing. Use it with Driver
Handle YB-06071.
YB-06027
Driveshaft Bushing Remover
2, 4, 5
This tool drives out the lower driveshaft bushing. Use it with
Driver Handle YB-06229.
YB-06029
Pinion Gear Bushing Installer
This tool installs the pinion gear bushing up into the
driveshaft housing
YB-06169
Needle Bearing Installer
This tool installs the reverse gear bearing housing oil seal and
is used as a guide to install the driveshaft needle bearing with
tools YB-06071 and YB-06168. It is also used with Bushing
Installer YB-06029 for driveshaft bushing installation.
8
2, 4, 5,
8
2, 4, 5,
8
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06016
Bearing Installer-Reverse Gear Bearing
4, 5
It installs the reverse gear ball bearing. Use it with Driver
Handle YB-06071.
Oil Seal Installer
4, 5
It installs the double oil seals in the reverse gear housing.
Use it with Driver Handle YB-06071.
YB-06178
Bushing Remover
4, 5
It removes the upper driveshaft bushing. Use it with Slide
Hammer YB-06096.
YB-06167
Bearing Cup Installer
1&2 CYLINDER 2-STROKE
YB-06023
4, 5, 8
It installs the forward gear bearing.
Use it with Driver Handle YB-06071.
YB-06021
Oil Seal Installer Reverse Gear Bearing
Housing
8
It installs the oil seals into the reverse gear bearing housing.
Use it with Driver Handle YB-06229.
YB-06015
Bearing Installer-Reverse Gear Bearing
It installs the reverse gear ball bearing.
Use it with Driver Handle YB-06071.
YB-06028
Driveshaft Bushing Remover and Installer
It properly removes and installs the driveshaft bushing.
Use it with Driver Handle YB-06229.
8, 9.9,
15
8, 9.9,
15
9
1&2 CYLINDER 2-STROKE
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06234
Bearing Housing Puller
8, 9.9,
15
When used with a universal puller (such as YB-06117), these
hooks will properly remove the reverse gear bearing housing
and propeller shaft. Includes: YB-06234-1 Hook Assembly,
YB-06234-2 Hook Assembly, Heavy Duty Washers (2), and
M6 x 1.0 Hex Nuts (2).
YB-06081
Needle Bearing Installer and Remover
9.9, 15
It installs and removes the driveshaft needle bearing. Use it
with Driver Handle YB-06071.
YB-06085
Outer Race Installer (Forward Gear)
9.9, 15
It drives in the forward bearing outer race. Use it with
Driver Handle YB-06071.
YB-01619
Test Propeller
9.9, 15
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. Intended for stationary
testing because they do not produce the thrust of a
standard propeller.
YB-06228
Driveshaft Holder Pinion Nut Torque Tool
9.9,15
It is used to loosen or torque the pinion nut.
It installs onto the driveshaft.
YB-06230
Driveshaft Needle Bearing Installer
and Remover
Removes and installs the driveshaft needle bearing. Use it
with Guide YB-06231 and Driver Handle YB-06229.
10
9.9,15
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06231
Driveshaft Needle Bearing Installer
9.9, 15
It properly installs the driveshaft needle bearing. Use it with
Pilot YB-06230 and Driver Handle YB-06229.
Oil Seal Installer
9.9, 15
It installs the double oil seals on the driveshaft.
Use it with Driver Handle YB-06071.
YB-06078
Pinion Nut Wrench
9.9, 15
It removes and installs the pinion nut for driveshaft removal.
YB-34232-C
Pinion Height Gauge Block
1&2 CYLINDER 2-STROKE
YB-06022
9.9, 15
It is required to select the proper pinion gear shims. It
eliminates the trial and error method of disassembly and
reassembly of the bearings and races repeatedly to determine
the correct shim. Includes: YB-34232-1 Bearing Plug Assembly,
YB-34232-2 Shim (Gauge Pinion Height), YB-34232-4 Bearing
Gauge, YB-34232-5 Instruction Sheet
11
1&2 CYLINDER 2-STROKE
NOTES
12
1
1& 2 Cylinder 4-sTroke
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-06308
Valve Guide Installer
F9.9
It installs the valve guides. It sets the proper depth for the
valve guide. Use it with Valve Guide Remover YM-01122.
1&2 CYLINDER 4-STROKE
YM-01122
Valve Guide Remover/Installer
F9.9
It properly removes the valve guides (5.5mm in diameter).
Also use it with Valve Guide Installer YB-06308 to install the
valve guides.
YM-01196
Valve Guide Reamer
F9.9
It is sized correctly for the 9.9 4-Stroke (5.5mm in diameter). It
is used to clean out the valve guide of any combustion
deposits.
YM-08035-A Valve Adjuster
F9.9
It includes 3 & 4mm hex. It is designed to help with critical
valve clearance adjustments.
YB-06868
Pulsar Coil Test Harness
F25/T25
It is used with a DVA meter and Peak Voltage Adaptor
YU-39991 to properly test pulser coil voltage output.
YM-04015
Valve Guide Installer
F25/T25
It installs the valve guides. It sets the proper depth for the
valve guide. Use it with Valve Guide Remover YM-01122.
YM-01122
Valve Guide Remover
F25/T25
It properly removes the valve guides (5.5mm in diameter). It
is also used with the Valve Guide Installer YM-04015.
YM-01196
Valve Guide Reamer
It is sized correctly for the 9.9 4-Stroke (5.5mm in diameter).
It is used to clean out the valve guide of any combustion
deposits.
14
F25/T25
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-01619
Test Propeller
F6, F8,
F9.9,
F15
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a
standard propeller.
Driveshaft Needle Bearing Installer/Remover
F9.9
The attachment is used for the removal and installation of
the driveshaft lower needle bearing. Use it with Driver
Handle YB-06229.
YB-06299
Pinion Bearing Shim Selector
F9.9
It is used to aid in shim selection for the pinion gear.
YB-06344
Forward Gear Shim Gauge
F25
This gauge is used to help get an accurate shim height for the
forward gear.
YB-39799
Reverse Gear Shim Gauge
1&2 CYLINDER 4-STROKE
YB-06298
F25
This gauge is used to help get an accurate shim height for the
reverse gear.
YB-06234
Bearing Housing Puller
F25/T25
The two puller legs are required to remove the bearing
housing. The Universal Puller YB-06117 is also required.
YB-06168
Oil Seal Installer
F25/T25
It is used to install the propeller shaft seals in the bearing
housing. It must be used with Driver Handle YB-06071.
YB-06079-A
Driveshaft Holder
The holder is specially designed to hold the driveshaft while
removing or reinstalling the pinion gear retaining nut.
F25/T25
15
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06022
Bearing Housing Oil Sealer Installer
F25
1&2 CYLINDER 4-STROKE
It is used to install the oil seals in the upper driveshaft
bearing housing. To be used with Driver Handle YB-06229.
YB-06082
Bearing Housing/Driveshaft Bearing
Remover/Installer
F25
It is used to remove and install propeller shaft bearing
housing inner bearing and driveshaft bearing. To be used
with Driver Handle YB-06229.
YB-06276-B
Reverse/Forward Gear Bearing Installer
F25/T25
The attachment is required to properly install the forward
and reverse gear ball bearing assembly. It also requires the
use of Driver Handle YB-06071.
YB-06231
Driveshaft Bearing Depth Plate
F25
Required for setting proper lower driveshaft bearing depth.
It also requires the use of Driver Handle YB-06029 and
Needle Bearing Attachment YB-06082.
YB-06085
Forward Gear Outer Race Installer
F25
It is used to install shims and outer bearing race for the
forward gear. It also requires the use of Driver Handle
YB-06071.
YB-06112
Bearing Housing Bearing/Oil Seal Remover
This adaptor is used to remove the propeller shaft bearing
housing seals and bearing. It also requires the use of the
Driver Handle YB-06071.
16
T25
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06111
Bearing Housing Bearing/Oil Seal Installer
T25
This adaptor is used to install the propeller shaft bearing
housing bearing assembly. It also requires the use of the
Driver Handle YB-06071.
Forward Gear Bearing Installer
T25
This adaptor is used to install the forward gear tapered roller
bearing.
YB-06063
Driveshaft Bearing Installer/Remover
T25
This adaptor is used to install or remove the driveshaft lower
bearing. For installation, Driver Handle YB-06071 and
Driveshaft Bearing Depth Plate YB-34473 are required.
For removal, Driver Handle YB-0671 is required.
YB-41446
Forward Gear Outer Race Installer
1&2 CYLINDER 4-STROKE
YB-06270-A
T25
It is used with Driver Handle YB-06071 to properly install
forward gear shims and outer bearing race.
YB-34473
Driveshaft Bearing Depth Plate
T25
The depth plate is used with Driveshaft Bearing
Installer/Remover YB-06063 and Driver Handle YB-06071 to
properly set the driveshaft lower bearing depth.
YB-06110
Driveshaft Outer Race Installer
T25
This adaptor is used to install the driveshaft upper bearing
outer race and shims. Use it with Driver Handle YB-06071.
17
POWER TRIM & TILT/MIDSECTION TOOLS
Part#
Description/Use
YB-06175-2B PTT Cylinder Wrench
1&2 CYLINDER 4-STROKE
It is used to remove or install trim and tilt cylinder end caps.
18
Application
3.3L
3
3 Cylinder 2-sTroke
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-06107
Connecting Rod Small End Bearing Installer
30
It installs the small end needle bearings into the
connecting rod.
YB-06346
Needle Bearing Remover and Installer
30
3 CYLINDER 2-STROKE
It is used to remove and install the driveshaft needle bearing.
Use it with Driver Handle YB-06229.
YB-06349
Crankshaft Seal Installer
30
It is used to install lower crankshaft seal. Use it with Driver
Handle YB-06071.
YB-06105
Connecting Rod Small End Bearing Installer
30
It installs the small end needle bearings into the
connecting rod.
YB-06106
Connecting Rod Small End Bearing Installer
40, 50
It installs the small end needle bearings into the
connecting rod.
YB-06287
Connecting Rod Small End Bearing Installer
It installs the small end needle bearings into the
connecting rod.
YB-06443
Peak Voltage Test Harness (3 Pin)
It is used along with YU-39991 Peak Voltage Adaptor and
YU-34899-A Digital Multimeter to check peak voltage output.
Photo not shown.
20
60, 70
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-01621
Test Propeller
25, 30
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a
standard propeller.
YB-06021
Oil Seal Installer Reverse Gear Bearing
Housing
25, 30
YB-06079-A
Driveshaft Holder Pinion Nut Torque Tool
30
It installs onto the driveshaft. Tighten it with Pinion Nut
Wrench YB-06078 to the proper specification.
YB-06081
Needle Bearing Installer and Remover
3 CYLINDER 2-STROKE
It installs the oil seals into the reverse gear bearing
housing. Use it with Driver Handle YB-06229.
25, 30
It installs and removes the driveshaft needle bearing.
Use it with Driver Handle YB-06071.
YB-06082
Needle Bearing Remover
25, 30
It installs and removes the needle bearing from the lower unit
bearing housing. Use it with Driver Handle YB-06299.
YB-06085
Outer Race Installer (Forward Gear)
25, 30
It drives in the forward bearing outer race.
Use it with Driver Handle YB-06071.
YB-06078
Pinion Nut Wrench
25, 30
It removes and installs the pinion nut for driveshaft removal.
21
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06075
Gland Nut Wrench
25, 30
It removes and installs the lower gland nuts. It is designed
specifically for Yamaha motors.
YB-06167
Bearing Cup Installer
25, 30
3 CYLINDER 2-STROKE
It installs the driveshaft bearing cup on 25 and 30 engines. It
installs the forward gear bearing on 4, 5, and 8 engines.
Use it with Driver Handle YB-06071.
YB-06168
Bearing Seal Installer
25, 30
It installs the reverse gear housing oil seals.
Use it with Driver Handle YB-06071.
YB-06169
Needle Bearing Installer
25, 30
It installs the reverse gear bearing housing oil seal and is used
as a guide to install the driveshaft needle bearing with tools
YB-06071 and YB-06168. It is also used with Bushing Installer
YB-06029 for driveshaft bushing installation.
YB-06234
Bearing Housing Puller
When used with a universal puller (such as YB-06117), these
hooks will properly remove the reverse gear bearing housing
and propeller shaft. Includes: YB-06234-1 Hook Assembly,
YB-06234-2 Hook Assembly, Heavy Duty Washers (2), and
M6 x 1.0 Hex Nuts (2).
YB-06368
Driveshaft Holder Pinion Nut Torque Tool
It is used to loosen or torque the pinion nut. It installs onto
the driveshaft.
22
25, 30
25
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06400
Reverse Gear Shim Gauge
It is used for selecting proper reverse gear shims.
25,
1988 ~ up
Pinion Height Gauge Block
25, 30
YB-34232-C
YB-39799
YB-06344
Reverse Gear Shim Gauge
It is used for selecting the proper reverse gear shims.
C30
1993 ~up
Shim Gauge
30
3 CYLINDER 2-STROKE
It is required to select the proper pinion, forward gear, and
reverse gear shims. It eliminates the trial and error method
of disassembly and reassembly of the bearings and races
repeatedly to determine the correct shim. Includes:
YB-34232-1 Bearing Plug Assembly, YB-34232-2 Shim
(Gauge Pinion Height), YB-34232-4 Bearing Gauge,
YB-34232-5 Instruction Sheet.
It is used for selecting proper forward and reverse
gear shims.
YB-34432-15 Adapter and Clamp
30
It is used with Pinion Shim Seal Selecting Tool YB-34432-D.
23
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06348
Driveshaft Seal Installer
30
It is used to install driveshaft seals. Use it with Driver Handle
YB-06229.
YB-06347
Bearing Inner Guide Plate
30
3 CYLINDER 2-STROKE
It is used with YB-06346 to adjust proper driveshaft bearing
depth. Use it with Driver Handle YB-06229.
YB-06345
Forward Gear Bearing Installer
30
It is used to install forward gear bearing. Also use Driver
Handle YB-06229.
YB-01611
Test Propeller
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a
standard propeller.
YB-06049
Driveshaft Holder-Pinion Nut Torque Tool
40, 50
40, 50
It is used to loosen or torque the pinion nut. It installs onto
the driveshaft.
YB-06110
Driveshaft Taper Roller Bearing Cup Installer
It installs the bearing cup for the driveshaft taper roller
bearing. Use it with Drive Handle YB-06071.
24
40, 50
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06111
Needle Bearing Installer
40, 50
It installs the reverse gear housing needle bearing.
YB-06112
Bearing Housing Needle Bearing Remover
40, 50
It is required to remove the needle bearing from the reverse
gear housing.
Reverse and Forward Gear Bearing Installer
40, 50
It installs the reverse gear ball bearing without damaging the
bearing. It also installs the forward gear into the forward gear
bearing.
YB-34474
Driveshaft Needle Bearing Depth Stop
40, 50
It insures the driveshaft needle bearing is installed to its
proper depth. Used with YB-06155 and Drive Handle
YB-06071.
YB-06277-A
Forward Gear Bearing Cup Installer
3 CYLINDER 2-STROKE
YB-06270-A
40, 50
It installs the forward gear bearing cup. Use with Drive
Handle YB-06071.
YB-34468-A
Reverse Gear Shim Gauge Set
40 ~ 90
It determines the proper reverse gear shim. Place on the
washer surface of the bearing housing, then measure the
clearance between the tool and top of the teeth on the gear.
Includes: YB-34468-1 (150, 200), YB-34468-2 (115, 130, 220,
225), YB-34468-3 (90, CV85), YB-34468-4 (40, 50, CV40, CV55),
YB-34468-5 (60, 70), YB-34468-6A (P150)
25
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06269
Water Pump Housing Bearing and Seal
Installer
40 ~ 90
It properly installs the water pump seal on 70 and 90 models.
It installs the rear bearing housing seal on 40, 50, 70, and
90 models.
YB-41446
Bearing Installer
3 CYLINDER 2-STROKE
It is used to install forward gear bearing outer cup. Use it with
Driver Handle YB-06071.
YB-01620
YB-06063
Test Propeller
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a standard
propeller.
60, 70,
75, 85,
90
Driveshaft Needle Bearing Remover and
Installer
70, 75,
80, 85,
90
It removes and installs the driveshaft needle bearing.
Use it with YB-34473.
YB-06151
Driveshaft Holder-Pinion Nut Torque Tool
It is used to loosen or torque the pinion nut. It installs onto
the driveshaft.
YB-06152
Bearing Housing Needle Bearing Installer
It installs the reverse gear housing needle bearing.
YB-06153
Bearing Housing Needle Bearing Remover
It is required to remove the needle bearing from the reverse
gear housing.
26
50 1995
75, 80,
85, 90
70, 75,
80, 85,
90
70, 75,
80, 85,
90
LOWER UNIT & POWER TRIM & TILT/MIDSECTION TOOLS
Part#
Description/Use
Application
YB-06155
Driveshaft Needle Bearing
Remover and Installer
70, 75,
80, 85,
90
It removes and installs the driveshaft needle bearing.
Use it with YB-34474.
YB-06156
Driveshaft Taper Roller Bearing Cup Installer
It installs the bearing cup for the driveshaft taper roller
bearing. Use it with Driver Handle YB-06071.
Gland Nut Wrench
70, 90
It removes and installs the lower gland nut.
YB-34473
Driveshaft Needle Bearing Depth Stop
It insures the driveshaft needle bearing is installed to its
proper depth. Use it with Driver Handle YB-06063.
YB-06276-B
Forward Gear Bearing Cup Installer
70, 90,
C55
3 CYLINDER 2-STROKE
YB-34447
70, 75,
80, 85,
90
70, 90
Installs the forward gear bearing cup. Use with
Driver Handle YB-06071.
POWER TRIM & TILT/MIDSECTION TOOLS
YB-34466
Power Tilt Cylinder Cap Wrench
C40, 50
It loosens and tightens the power tilt cylinder cap.
YB-06175-2B Power Tilt Cylinder Cap Wrench
40 - 90
It loosens and tightens the power tilt cylinder cap.
27
3 CYLINDER 2-STROKE
NOTES
28
3
3 Cylinder 4-sTroke
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-06868
Pulser Coil Test Harness
F30, F40
This test harness is used with a DVA meter and Peak Voltage
Adaptor YU-39991, to measure Pulser Coil Voltage Output.
YM-04019
Valve Spring Compressor
F30 ~ F40
3 CYLINDER 4-STROKE
It is used with the valve spring compressor with the correct
attachment to depress the valve spring retainer so the valve
cotters may be removed or installed.
YB-06320
Valve Attachment
F30 ~ F40
Use this attachment with the Valve Spring Compressor
YB-04019 to depress the valve spring retainer so the valve
cotters may be removed or installed.
YB-06801
Valve Guide Remover
It is used to remove the valve guides from the cylinder head.
YM-04015
Valve Guide Installer
F30 ~ F40
F30 ~ F40
It is used to properly install the valve guides into the cylinder
head.
YM-04066
Valve Guide Reamer
F30 ~ F40
It is used to properly remove any combustion deposits in the
valve guide.
YB-06867
Test Harness, CDI Output
Use it with a DVA meter and the Peak Voltage Adaptor
YU-39991, to measure the output voltage or the CDI unit.
30
F30, F40
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-01621
Test Propeller
F30, F40
It is correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a
standard propeller.
YB-06079
Driveshaft Holder
F30, F40
It is used to hold the driveshaft to allow for pinion nut
removal or installation.
Bearing Housing Bearing/Oil Seal Remover
F30, F40
When used with Driver Handle YB-06071, this adaptor is
designed to remove the propeller shaft bearing carrier
bearing and seals.
YB-06111
Bearing Housing Bearing/Installer
F30, F40
3 CYLINDER 4-STROKE
YB-06112
When used with Driver Handle YB-06071, this attachment
will properly install the propeller shaft bearing housing
bearing.
YB-06168
Oil Seal Installer
F30, F40
When used with Driver Handle YB-06071, this attachment
will properly install the propeller shaft bearing housing seals.
YB-06276-A
Reverse Gear Bearing Installer
F30, F40
When used with Driver Handle YB-06071, this attachment
will properly install the roller bearing on the reverse gear.
YB-06270-A
Forward Gear Bearing Installer
This installer is designed to properly install the forward gear
tapered roller bearing.
F30, F40
31
LOWER UNIT & POWER TRIM & TILT/MIDSECTION TOOLS
Part#
Description/Use
Application
YB-06063
Driveshaft Needle Bearing Remover/Installer
F30, F40
When used with Driver Handle YB-06071, this attachment
will remove the lower driveshaft bearing. For installation of
the bearing, Driveshaft Bearing Depth Plate YB-34473 is
required.
YB-41446
Forward Gear Outer Race Installer
F30, F40
3 CYLINDER 4-STROKE
When used with Driver Handle YB-06071, this is used to
install the forward gear shims and outer race in the gear
housing.
YB-34473
Driveshaft Bearing Depth Plate
F30, F40
It is used with Driveshaft Needle Bearing Remover/Installer
YB-06063 and Driver Handle YB-07071. This plate properly
sets the driveshaft lower bearing depth.
YB-06110
Bearing/Oil Seal Depth Plate
F30, F40
It is used with Driver Handle YB-06071. This adaptor
properly installs the pinion shims and upper bearing
outer race.
POWER TRIM & TILT/MIDSECTION TOOLS
YB-06175-2B Trim Cylinder Wrench
This wrench is specially designed to remove and install the
trim cylinder end cap.
32
F25
4
4& 6 Cylinder
2-sTroke
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-06240
Connecting Rod Small End
Bearing Installer
V4
1984 ~ 92,
V6
1984 ~ 91
It installs the small end needle bearings into the
connecting rod.
YB-06202
Engine Lifting Hook
V4, 2.6L
It allows easy lifting of the engine. It properly supports all
Yamaha V-4 and V-6 engines and attaches to the crankshaft.
4&6 CYLINDER 2-STROKE
YB-06205
Crankshaft Bearing Installer
YB-06244
Crankshaft Upper and Lower Seal Installer
It properly installs the upper and lower crankhaft oil seals.
Use it with Driver Handle YB-06071.
YB-37462
Standard 90mm Piston Ring Installer
This specially designed ring compressor allows easy piston
installation by just pushing the piston into the taper cup
while the cup is against the cylinder block.
YB-37463
Oversize 90mm Piston Ring Installer
This specially designed oversize ring compressor allows easy
piston installation by just pushing the piston into the taper
cup while the cup is against the cylinder block.
34
V4, 2.6L
It removes and installs the crankshaft upper roller bearing. It
it used with a press to remove the bearing and has a bearing
pilot to install the bearing to the proper depth.
V4, 2.6L
3.1L, 3.3L
V4, V6,
2.6L, 3.1L
V4, V6,
2.6L, 3.1L
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-06870
Lighting Coil Test Lead
V4 ~ V6
2.6L, OX66
It is used with a DVA meter to measure the lighting coil
output voltage.
YB-06283
Throttle Position Sensor Test Lead
Use it with a digital voltmeter (such as YU-34899-A) to
measure the voltage output for throttle position
sensor adjustment.
Note: Voltmeter must read output as low as 0.41 volts.
YB-06857
2.6L, 220,
225,
1994 ~ 89
Peak Voltage Test Harness (3 Pin)
YB-06771
Charge Coil Test Harness-OX66
It is used with DVA meter and Peak Voltage Adaptor
YB-39991 to measure charger coil output voltage.
YB-06772
Pulser Coil Test Harness
It is used with a DVA meter and Peak Voltage Adaptor
YB-39991 to measure pulser coil output voltage.
YB-06795
Diagnostic Test Lead Updated YB-06444
The indicator light is used to identify an engine
self-diagnostic warning code.
Consists of YB-06444 & YB-06794
V6,
1990 & up
OX66
V6,
1990 & up
OX66
4&6 CYLINDER 2-STROKE
It is used along with YU-39991 Peak Voltage Adaptor and
YU-34899-A Digital Multimeter to check peak voltage output.
2.6L,
3.1L,
3.3L
35
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-44478
O2 Sensor Wrench
OX66,
2.6L HPDI
This opened end wrench is specifically designed to remove or
tighten the O2 sensor.
YB-06766
Fuel Pressure Gauge
OX66, HPDI
This gauge is used to measure VST fuel pressure.
YB-06867
Crank Position Sensor Test Harness
4&6 CYLINDER 2-STROKE
It is used with a DVA meter. This harness allows for the
measurement of output voltage.
YB-06868
Air Temp Sensor Tester
OX66, HPDI
OX66, HPDI
It is used with a DVA meter. This harness allows for the
measurement of output voltage.
YB-06869
Air Pressure Sensor Tester
OX66, HPDI
It is used with a DVA meter. This harness allows for the
measurement of output voltage.
YB-06879
Pulsar Coil Test Harness
HPDI
It is used with a DVA meter and the Peak Voltage Adaptor
YB-39991. This test harness is used to measure output
voltage.
YB-06888
Lighting Coil Test Lead, Isolator Lead
It is used with a DVA meter. This test harness is used to
measure output voltage.
36
HPDI
POWER HEAD & LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06887
Lighting Coil, Rectifier/Regulator Test Lead
HPDI
It is used with a DVA meter for measurement of
output voltage.
YB-06861
Injector Test Lead
It is used with a DVA meter to measure output voltage.
photo not shown.
YS-01880-A
Primary Sheave Holder
F115 ~
F225
HPDI
It is used to hold the primary high pressure fuel pump pulley
for removal or installation of the pulley mounting nut.
Engine Lifting Hook
3.1L
It threads onto the crankshaft threads to allow for lifting.
YB-06016
Bearing Installer
It is used with Driver Handle YB-06071 to properly install the
lower crankshaft seal.
3.3L
4&6 CYLINDER 2-STROKE
YB-06442
LOWER UNIT TOOLS
YB-01624
Test Propeller
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a
standard propeller.
YB-01631
Test Propeller
V4
except
L130
L130
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a
standard propeller.
37
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06199-A
Bearing Cup Installer
V4
It installs the forward gear bearing outer race. Use it with
Driver Handle YB-06071.
YB-06200
Forward Gear Needle Bearing and
Tapered Roller Bearing Installer
V4
It installs the needle bearing into the forward gear and the
roller bearing onto the gear hub. Use it with Driver Handle
YB-06071.
4&6 CYLINDER 2-STROKE
YB-06194
Driveshaft Needle Bearing Installer
and Remover
V4, V6
It removes and installs the lower driveshaft needle bearing.
Use it with Driver Handle YB-06071 and Depth Plate
YB-06213.
YB-06195-A
Oil Seal Installer
V4, V6
It installs both oil seals properly into the reverse gear
bearing housing. Use it with Driver Handle YB-06071.
YB-06196
Driveshaft Needle Bearing Installer
and Remover
V4, V6
It removes and installs the needle bearing from the driveshaft
and propshaft bearing housing. Use it with Driver Handle
YB-06071.
YB-34447
Gland Nut Wrench
It removes and installs the bearing housing gland nut.
YB-06335
Propeller Shaft and Bearing Housing Remover
For use with Slide Hammer YB-06096, threads onto the
propeller shaft.
38
V4, V6
V4, V6
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06213
Needle Bearing Guide Plate
V4, V6
It properly installs the driveshaft needle bearing squarely into
the housing bore. Use it with Bearing Driver YB-06194 and
Driver Handle YB-06071.
YB-06376
Needle Bearing Installer
Use it with Driver Handle YB-06071 to install the reverse gear
bearing into spacer.
YB-06377
Space Installer
Use it with Driver Handle YB-06071 to properly install
reverse gear spacer.
Needle Bearing Installer
Use it with Driver Handle YB-06071 to properly install
forward gear bearing.
YB-06201
Driveshaft Holder-Pinion Nut Torque Tool
Use it to loosen or torque the pinion nut. It installs onto
the driveshaft.
YB-06207
Bearing Housing Puller
When used with a universal puller (such as YB-06117), these
hooks will properly remove the reverse gear bearing housing
and propeller shaft. Includes: YB-06207-1 Hook Assembly,
YB-06207-2 Hook Assembly, Heavy Duty Washers (2), and
M8 x 1.25 Hex Nuts (2).
Counter
Rotation
V4
Counter
Rotation
V4
V4, V6,
2.6L,
3.1L,
3.3L
4&6 CYLINDER 2-STROKE
YB-06378
Counter
Rotation
V4
V4, V6,
2.6L,
3.1L,
3.3L
39
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06052
Shift Rod Push Arm
It shifts the lower unit into forward, neutral or reverse when
the lower unit has been removed from the engine.
2.6L,
3.1L,
3.3L
Driveshaft Bearing Installer
V6
YB-06246
It drives the driveshaft needle bearing into its proper location.
Use it with Driver Handle YB-06071.
YB-06258
Forward Bearing Race Installer
V6
4&6 CYLINDER 2-STROKE
It installs the forward gear bearing outer race. Use it with
Driver Handle YB-06071.
YB-06261
Forward Gear Needle Bearing Installer
It installs the forward gear needle bearings. It is designed to
install both needle bearings to their proper depth. Use with
Driver Handle YB-06071.
YB-34449-A
Driveshaft Puller
V6
It slides over the driveshaft and locks against the driveshaft
key. Thread in Slide Hammer YB-06096 and remove the
driveshaft from the pinion gear.
YB-01626
Test Propeller
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a standard
propeller.
YB-34453
Forward Gear & Tapered Roller Bearing
Separator
It separates the forward gear from the forward gear bearing
without damaging the gear or bearing. It is used with a
suitable pilot and a press.
40
V6
V-6
except
L 2.6L
&
L 3.1L,
V-6 except
D150/
DX150
LOWER UNIT TOOLS
Part#
Description/Use
YB-34432-97 Driveshaft Shim Select Adapter
It is used to help properly select the correct shims for the
pinion gear.
YB-42223
Gland Nut Wrench
It is designed to properly remove and install the bearing
housing gland nut.
YB-42224
Pinion Nut Wrench
It is designed to properly hold the pinion nut for removal or
installation.
Propshaft Seal/Bearing Installer
It is specifically designed for outer propshaft seal and bearing
installation. Use it with Driver Handle YB-06071.
YB-42227
Prop End Seal Bearing Driver
It is used with Driver Handle YB-06071 for installing bearing
housing seals.
YB-42229
Bearing Driver
Use it with Driver Handle YB-06071 to install the forward
bearing in the bearing housing.
YB-06336
Bearing Race Installer
Use it with Driver Handle YB-06071 to install the reverse gear
outer bearing in the bearing race and shims.
D150,
DX150
D150,
DX150
D150,
DX150
D150,
DX150
D150,
DX150
4&6 CYLINDER 2-STROKE
YB-42225
Application
D150,
DX150
Counter
Rotation
2.6L
41
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06337
Needle Bearing Installer
Counter
Rotation
2.6L
It is used to install the forward gear bearing.
YB-06338
Shim Gauge
It is used to help properly select forward and reverse
gear shims.
YB-06339
Shim Gauge
4&6 CYLINDER 2-STROKE
It is used to help properly select forward and reverse
gear shims.
YB-06436
Bearing Separator
It is designed to help remove the bearing from the
forward gear.
YB-06437
Bushing Remover/Install
Counter
Rotation
2.6L
Counter
Rotation
2.6L
3.1L
3.1L
It is used with Driver Handle YB-06071 to remove/install the
forward gear bushing. photo not shown.
YB-06433
Stopper Ring
3.1L
It is used as a depth plate for proper forward gear needle
bearing installation.
YB-06439
Shim Gauge
It is used to help properly select the shim height or the
forward gear.
42
3.1L
(RH)
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06440
Shim Gauge
3.1L,
LZ250
3.3L,
(LH)
It is used to properly measure the forward gear to determine
the accurate shims.
YB-06048
Gland Nut Wrench
It removes and installs lower gland nuts. It is designed
specifically for Yamaha motors. It is manufactured from high
strength alloy steel and heat-treated for strength and
durability.
YB-06430
Forward Bearing Installer
Use it with Driver Handle YB-06071 to install the reverse gear
bearing in the bearing housing.
Taper Roller Bearing Installer
Use it with Driver Handle YB-06071 to properly install the
forward gear outer bearing race.
YB-06434
Needle Bearing Installer
Use it with Driver Handle YB-06071 to remove/install the
needle bearing into reverse gear retainer.
YB-06435
Needle Bearing Installer
Use it with the Needle Bearing Installer/Remover YB-06213
and Pinion Gear Bushing Installer YB-06029-4 to properly
install the outer race of the lower driveshaft bearing.
YB-06441
Pinion Gear Shim Gauge
It is used to determine shim measurement of the pinion gear.
3.1L,
3.3L
3.1L,
3.3L
3.1L,
3.3L
(LH)
4&6 CYLINDER 2-STROKE
YB-06431
Counter
Rotation
3.1L
3.1L,
3.3L
3.1L,
Z250
3.3L
43
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-41707
Reverse Gear Bearing Remover
Use it with Universal Puller YB-06117. It is used to remove
the reverse gear retainer.
Counter
Rotation
3.1L, 3.3L
Oil Seal Installer
3.3L
YB-06168
Use it with Driver Handle YB-06071 to remove propeller shaft
bearing housing bearing and seals.
YB-06085
Oil Seal Installer
4&6 CYLINDER 2-STROKE
It is used with Driver Handle YB-06071 to install seals for the
driveshaft housing and install propeller shaft bearing
housing seals.
YB-06109
Bearing Outer Race Attachment
3.1L,
3.3L
3.3L
It is used to properly install the reverse gear into the bearing
housing.
YB-06432
Roller Bearing Installer/Remover
3.3L
Use it with Driver Handle YB-06071 to remove and install
driveshaft lower bearing.
YB-06276-B
Forward Gear Bearing Cup Installer
3.3L
It is used to install the taper roller bearing onto the
forward gear.
YB-06439
Forward & Reverse Gear Shim Gauge
It is used for measuring proper shim height of the forward
and reverse gears.
44
Z250,
3.3L
LOWER UNIT & POWER TRIM & TILT/MIDSECTION TOOLS
Part#
Description/Use
Application
YB-06578
Gland Nut Wrench
Z250,
3.3L
It is used to remove the porpeller shaft bearing housing
gland nut.
YB-06440-A
Shim Gauge
It is used to properly measure the forward gear to determine
the accurate shims.
YB-06441-3
Pinion Gear Shim Tool
It is used to properly measure the pinion gear shim height.
Forward & Reverse Gear Shim Tool
The shim gauge is designed to help in the selection for the
forward and reverse gears.
VZ225/250
3.3L
VZ225/250
3.3L
POWER TRIM & TILT/MIDSECTION TOOLS
YB-06548
TNT Wrench, Showa System
It is specially designed to remove the end caps on the tilt
cylinders.
YB-06175-C
TNT Wrench
It is required to remove the nut on the trim and tilt cylinder.
Both tools incorporate a 3/8” square drive for use with a
torque wrench for proper installation. The trim Wrench fits all
trim and tilt cylinders. The tilt Wrench fits all trim and tilt
cylinders (except 64E pumps). Includes: Trim Wrench
YB-06175-1A, Tilt Wrench YB-06175-2B.
YB-06776
PTT Pressure Gauge
It is used to measure the PTT system pressure.
1997 &
Up, V4,
V6 2.6L,
VX200/
225 3.1L
4&6 CYLINDER 2-STROKE
YB-06439-2
3.1L,
LZ250
3.3L
(LH)
V4,
V6 2.6L,
Except
Showa
V4 ~ V6
2.6L
1997 &
Up, V4,
V6 2.6L,
VX200/
225
45
POWER TRIM & TILT/MIDSECTION TOOLS
Part#
Description/Use
Application
YB-06569
Tilt Rod Wrench
F200/225
Use it with the PTT Piston Vise Tool YB-06572 to the remove
top pin eyelet. Enables end cap servicability. Photo not shown
YB-06548
Tilt Wrench, Showa System
3.1L
It is specially designed to remove the end caps on the tilt
cylinders.
YB-06544
PTT Cylinder End Cap
4&6 CYLINDER 2-STROKE
It is used to remove or install the PTT cylinder end caps.
Photo not shown.
YB-06572
PTT Piston Vise Tool
Use it with Tilt Rod Wrench YB-06569 to remove the tilt
cylinder pin eye. This enables tilt cylinder end cap service.
YB-06581
PTT Pressure Gauge Adapter
It is used with the PTT Pressure Gauge YB-06580 to measure
operational pressure of the PTT system.
YB-06580
PTT Pressure Gauge
Use it with Adaptor YB-06581 to measure operational
peresure of the PTT system. Photo not shown.
YB-06175-2B PTT Cylinder Wrench
It is used to remove or install trim and tilt cylinder end caps.
46
F75 ~
F100
3.1L
2002 &
UP, 3.3L
3.1L,
3.3L
3.1L,
3.3L
3.3L
4
4& 6 Cylinder
4-sTroke
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-06770
Lighting Coil Test Lead
F40-4~
F225
Use it with a DVA meter and Peak Voltage Adapter YB-39991
to measure voltage output.
YB-06767
Test Lead, Crank Position Sensor,
ECU Output
Use it with a DVA meter and Peak Voltage Adapter YB-39991
to measure voltage output.
YM-01122
Valve Guide Remover
4&6 CYLINDER 4-STROKE
It is specifically designed to remove the valve guide from the
cylinder head.
YM-01196
Valve Guide Reamer
It is designed to clean out combustion deposits from inside
the valve guide.
YW-06355
Crankshaft Holder
It is used to hold or rotate the crankshaft when working on
the engine.
YB-06871
Rectifier/Regulator Test Harness
It is used with a DVA meter to test the voltage output.
YB-06801
Valve Guide Remover
It is specifically designed to remove the valve guide from the
cylinder head.
48
F40-4~
F/T60
F40-4 ~
F/T50
F40-4 ~
F/T50
F40-4 ~
F/T50
F/T50
2001 ~ up,
F60
F/T50
2001 ~ up,
F60
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-06562
Crankshaft Holder
F/T50
2001 ~ up,
F60
It is used to hold or rotate the crankshaft while performing
engine work.
YB-06554
Valve Spring Compressor Adapter
It is used with Valve Compressor YM-01253. This adapter
allows for spring retainer compressor to remove or install the
valve cotters.
YM-04066
Valve Guide Reamer
It is required to clean combustion deposits from the internal
bore of the valve guide.
Pulsar Coil Test Lead
It is used with a DVA meter and the Peak Voltage Adapter
YB-39991 to measure voltage output.
YB-06552
Crankshaft Holder
It is used to hold or rotate the crankshaft while performing
engine work.
YB-06857
F75 ~
F115
F75 ~
F100
F75 ~
F115
4&6 CYLINDER 4-STROKE
YB-06872
F40-4 ~
F115
Throttle Position Sensor Test Lead
It is used with a DVA meter to measure and adjust the
throttle position voltage.
Note: Meter must read 0.40 volts.
YB-45775
Timing Belt Driven Gear Socket
F75~ F115
Socket depth is specifically designed to remove and install the
timing belt driven spacer from the crankshaft.
49
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-06791
Pulser Coil Test Lead
F115
It is used with a DVA meter and the Peak Voltage Adapter
YB-39991 to measure voltage output.
YM-04064-A Valve Guide Remover/Installer
F115
It is specifically designed to remove and install the valve
guides from the cylinder head.
YB-06790
Lighting Coil Test Lead
F115
It is used with a DVA meter and the Peak Voltage Adapter
YB-39991 to measure voltage output.
4&6 CYLINDER 4-STROKE
YB-06795
Diagnostic Checking Lead
(Updated YB-06444)
The diagnostic indicator light flashes the ECU’s
self-diagnostic code.
Consists of YB-06444 & YB-06794
YB-06766
YB-06869
Fuel Pressure Gauge
It is used for checking VST fuel pressure.
F115 ~
F225
Test Lead, Intake Manifold Pressure,
Oil Pressure
F115,
F200/225
The test harness is to be used with a DVA meter to measure
output voltage.
YB-06792
ECU Output Test Lead
It is used with a DVA meter and the Peak Voltage Adapter
YB-39991 to measure voltage output.
50
F115 ~
F225
F115 ~F225
POWER HEAD TOOLS
Part#
Description/Use
Application
YB-06793
Throttle Position Sensor Test Lead
F115 ~
F225
It is used with a DVA meter to measure and adjust throttle
position sensor voltage.
NOTE: DVA meter must be able to read 0.40 volts.
YB-06861
YB-06810
Injector Test Lead
It is used with a DVA meter to measure output voltage.
F115 ~
F225
Valve Guide Installer
F200/225
It is to be used with the Valve Guide Remover YB-06801. It is
used to preset the valve guide depth in cylinder head.
Valve Spring Compressor Adaptor
F200/225
The adaptor, when used with the Valve Spring Compressor
YM-01253, compresses the valve for valve cotter removal or
installation.
YB-38831/YB-06871
Pulsar Test Lead
F200/225
It is used with a DVA meter and the Peak Voltage Adapter
YB-39991 to measure voltage output.
YB-06887
Lighting Coil, Rectifier/Regulator Test Lead
It is used with a DVA meter and the Peak Voltage Adapter
YB-39991 to measure voltage output.
4&6 CYLINDER 4-STROKE
YB-06320
F200/225
51
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-01611
Test Propeller
F40-4 ~ F60
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a
standard propeller.
YB-06079
YB-34468-5
Driveshaft Holder
It is used to hold the driveshaft while installing or removing
the pinion gear nut.
F40-4 ~ F60,
T50
2000 & Older
Reverse Gear Shim Gauge
T50
4&6 CYLINDER 4-STROKE
It is used to measure the reverse gear shim.
YB-34447
Gland Nut Wrench
It is designed to ease the removal or installation of the
propeller shaft bearing housing gland nut.
YB-06111
Propshaft Needle Bearing Attachment
F40-4 ~
F/L115
F40-4 ~ F50
Use it with Driver Handle YB-06071 to install the propeller
shaft bearing housing bearing.
YB-06071
Propeller Shaft Oil Seal Installer
F40-4 ~ F50
Use it with Driver Handle YB-06071 to install the propeller
shaft bearing housing seals.
YB-06063
Driveshaft Needle Bearing Attachment
Use it with Driver Handle YB-06071 to remove the driveshaft
lower bearing. Use it with Driver Handle YB-06071 and
Depth Plate YB-34473 to install the driveshaft lower bearing.
52
F40-4 ~
F/T50,
F60
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-41446
Forward Gear Bearing Installer
F40-4 ~ F50
Use it with Driver Handle YB-06071 to install the forward
gear shims and outer bearing race.
YB-06270-A
Forward Taper Roller Bearing Installer
It is designed for proper installation of the forward gear
tapered roller bearing.
YB-34473
Driveshaft Needle Bearing Depth Stop
Use it with Driver Handle YB-06071 and Drive Shaft Needle
Bearing Attachment YB-06063 to properly set the bearing
depth.
Driveshaft Bearing Installer
Use it with Driver Handle YB-06071 to install the upper drive
shaft shims and outer bearing race.
YB-06153
Propshaft Needle Bearing Attachment
Use it with Driver Handle YB-06071 to remove the oil seals
and the bearing from the propeller shaft bearing housing.
YB-06152
Propshaft Needle Bearing Attachment
F40-4 ~
F/T50,
F/T60
F40-4 ~
F50
T50 ~
F100
4&6 CYLINDER 4-STROKE
YB-06110
F40-4 ~
F/T50,
F60
T50
Use it with Driver Handle YB-06071 to install the propeller
shaft bearing housing bearing.
YB-06269
Propeller Shaft Oil Seal Installer
Use it with Driver Handle YB-06071 to install the propeller
shaft bearing housing prop shaft seals.
T50 ~
F100
53
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06276
Forward Gear Bearing Installer
T50
Use it with Driver Handle YB-06071 to install forward gear
shims and outer bearing race.
YB-06155
Driveshaft Bearing Installer
T50
Use it with Driver Handle YB-06071 and Depth Plate
YB-34473 to properly set the lower driveshaft bearing.
YB-06156
Driveshaft Outer Race Installer
4&6 CYLINDER 4-STROKE
Use it with Driver Handle YB-06071 to install the upper drive
shaft shims and outer bearing race.
YB-06109
Forward Bearing Cup Installer
T60
Use it with Driver Handle YB-06071 to install the reverse gear
into bearing housing.
YB-06155
Driveshaft Bearing Installer/Remover
Use it with Driver Handle YB-06071 and Depth Plate
YB-34473 to properly set the lower driveshaft bearing.
YB-06276-B
Forward Gear Bearing Cup Installer
Use it with Driver Handle YB-06071 to install forward gear
shim and outer bearing race.
YB-06112
Bearing Housing Bearing Remover
Use it with Driver Handle YB-06071 to install the forward
gear inner bushing.
54
T50 ~
F100
T60 ~
F100
T60 ~
F100
T60
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06200
Forward Gear Needle Bearing
T60
It is used to properly install the forward gear tapered needle
bearing.
YB-06244
Driveshaft Seal Installer
T60
Use it with Driver Handle YB-06071 to install upper
driveshaft seals.
YB-06049
Driveshaft Holder
It is used to hold the driveshaft while removing or installing
the pinion gear nut.
YB-34474
Test Propeller
It correctly loads Yamaha motors for diagnosing engine
performance at different RPM’s. It is intended for stationary
testing because they do not produce the thrust of a
standard propeller.
F75 ~
F115,
Except
LF115
Driveshaft Needle Bearing Depth Stop
F75 ~ F100
Use it with Driver Handle YB-06071 and Needle Bearing
Attachment YB-06155 to properly install the driveshaft lower
bearing.
YB-06151
Driveshaft Holder
It is used to hold the driveshaft while removing or installing
the pinion gear nut. (90890-06519)
YB-06200
Reverse/Forward Gear Bearing Installer
4&6 CYLINDER 4-STROKE
YB-01624
F/T50
2001 ~ up
F75 ~
F/L115
F115
It is used to install ball bearing onto reverse gear.
55
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06213
Driveshaft Bearing Depth Plate
F115
Use it with Driver Handle YB-06071 and Bearing/Oil Seal
Attachment YB-06194 to properly install lower driveshaft
bearing.
YB-34468-2
Reverse Gear Shim Tool
F115
It is used to properly measure the reverse gear for shim
height.
YB-06199
Forward Gear Outer Race Installer
F115
4&6 CYLINDER 4-STROKE
Use it with Driver Handle YB-06071 to properly install
forward gear shim and outer bearing race.
YB-06052
Shift Rod Push Arm
F115 ~F225
It shifts the lower unit into forward, neutral or reverse when
the lower unit has been removed from the engine.
YB-06378
Forward Gear Bearing Installer
LF115
Use it with Driver Handle YB-06071 to properly install
forward gear inner bearing.
YB-06376
Reverse Gear Bearing Remover/Installer
LF115
Use it with Driver Handle YB-06071 to remove/install the
reverse gear bearing from the retainer.
YB-06377
Reverse Gear Bearing Retainer/Installer
Use it with Driver Handle YB-06071 to install the reverse gear
bearing retainer.
56
LF115
LOWER UNIT TOOLS
Part#
Description/Use
Application
YB-06337
Bearing Housing Bearing Installer
LF115
Use it with Driver Handle YB-06071 to install the propeller
shaft inner bearing.
YB-34468-2
Forward Gear Shim Tool
LF115
It is used to determine the correct shims required for the
forward gear.
YB-06430
Rear Propeller Shaft Bearing Installer
LF115
Use it with Driver Handle YB-06071 to properly install the
propeller shaft bearing housing tapered roller bearing.
Test Propeller
LF115
It correctly load Yamaha motors for diagnosing engine
performance at different rpm’s. It is intended for stationary
testing because they do not produce the thrust of a standard
propeller.
YB-06520
Driveshaft Holder
F200/225
It is used to hold the driveshaft while removing or installing
the pinion gear nut. Photo not shown.
YB-06048
Gland Nut Wrench
It removes and installs the lower gland nut. It is designed
specifically for Yamaha motors. It is manufactured from high
strength alloy steel and heat-treated for strength and
durability.
YB-06194
Driveshaft Needle Bearing Installer
and Remover
It removes and installs the driveshaft needle bearing. Use it
with Driver Handle YB-06071 and Depth Plate YB-06213.
4&6 CYLINDER 4-STROKE
YB-01631
Counter
Rotation
F200/225
FL/115 ~
F225
57
LOWER UNIT & POWER TRIM & TILT/MIDSECTION TOOLS
Part#
Description/Use
Application
YB-06195-A
Oil Seal Installer
FL/115 ~
F225
it installs both oil seals properly into the reverse gear bearing
housing. Use it with Driver Handle YB-06071.
YB-06196
Driveshaft Needle Bearing Installer
and Remover
FL/115 ~
F225
It removes and installs the needle bearing from the driveshaft
and propshaft bearing housing. Use it with Driver Handle
YB-06071.
POWER TRIM & TILT/MIDSECTION TOOLS
YB-06175-2B Trim/Cylinder Wrench
4&6 CYLINDER 4-STROKE
It is used to remove most PTT cylinder end caps.
YB-06569
YB-06572
It is used with the Piston Vise Attachment YB-06572 to
remove the tilt pin eye to service, tilt cylinder end cap.
Photo not shown.
1997 &
Up, V4,
V6 2.6L,
VX200/
225
PTT Piston Vise Tool
F200/225
Tilt Rod Wrench
Use it with Tilt Rod Wrench YB-06569 to remove the top pin
eyelet. It enables tilt cylinder end cap servicability.
YB-06548
YB-06548
Tilt Cylinder End Cap Wrench
It is used to remove or install the cylinder end cap.
F40 ~ F60,
FL/115
TNT Wrench, Showa System
F75 ~ F115
It is used to remove or install the PTT cylinder end caps.
58
F40-4 ~
F/L115
POWER TRIM & TILT/MIDSECTION TOOLS
Part#
Description/Use
Application
YB-06544
PTT Cylinder End Cap
F75 ~ F100
It is used to remove or install the PTT cylinder end caps.
Photo not shown.
YB-06776
PTT Pressure Gauge
It is used to measure the PTT system pressure.
YB-06548
YB-06572
Tilt Wrench, Showa System
F115
F40 ~ F60,
F115
PTT Piston Vise Tool
F200/225
Use it with Tilt Rod Wrench YB-06569 to remove the top pin
eyelet. It enables tilt cylinder end cap servicability.
YB-06581
PTT Pressure Gauge
It is used to measue the PTT system pressure.
F200/225
4&6 CYLINDER 4-STROKE
It is used to remove or install the PTT cylinder end caps.
59
4&6 CYLINDER 4-STROKE
NOTES
60
W
WaTerCrafT
WATERCRAFT
Part#
Description/Use
Application
YM-04019
Valve Spring Compressor
RX-1,
RX-1ER,
FX140,
FX Cruiser,
SR230
It is used to remove valve spring retainers.
YM-04108
YM-04114
Optional Adapters for YM-04019
Compressor Adapter 20mm
Compressor Adapter 19.5mm
These are adapters for smaller/larger valve sizes.
YM-04111
YM-04116
Valve Guide Driver 4mm
Valve Guide Driver 4.5mm
They are used to remove intake (4mm) and exhaust (4.5mm)
valve guides on 5 valve heads.
YM-04112
YM-04117
Valve Guide Installer 4mm
Valve Guide Installer 4.5mm
They are used to install intake (4mm) and exhaust (4.5mm)
valve guides on 5 valve heads.
WATERCRAFT
YM-04113
YM-04118
Valve Guide Reamer 4mm
Valve Guide Reamer 4.5mm
They are used to establish correct valve to guide clearance.
Intake (4mm)/Exhaust (4.5mm).
YM-45469
Valve Keeper Remover & Installer Tool
This tool effectively removes the keepers quickly & easily. It
works great for changing valve springs without removing
the head (must fill cylinders with compressed air).
YM-34483
YU-01304
Narrow Feeler Gauge Set
FX140,
FX Cruiser,
SR230
FX140,
FX Cruiser,
SR230
FX140,
FX Cruiser,
SR230
FX140,
FX Cruiser,
SR230
This set includes 13 blades for use with 5-valve 4-stroke
engines. Standard range: .002” - .014”.
FX140,
FX Cruiser,
SR230
Piston Pin Removal Tool
Universal
It removes 12mm-25mm pins from 40mm-100mm pistons.
YB-06107
62
Connecting Rod Small End Bearing Installer
WR/WJ500
WATERCRAFT
Part#
Description/Use
YM-04044
Piston Ring Compressor
Range: 61-66mm diameter. Can be used on two or four stroke
engines to compress the rings for piston installation.
YM-08037
Piston Ring Compressor
Range: 54-127mm diameter. Alternate to YM-04044.
YB-06139
Flywheel Holder
It holds the flywheel securely in place for nut removal.
YW-06547
Flywheel Holder
Application
Universal
Universal
WR/WJ500
All 760
It bolts to the crankcase and secures the flywheel for bolt
removal/installation.
YW-06550
Flywheel Holder
It bolts to the crankcase and secures the flywheel for bolt
removal/installation.
Flywheel Holder
It bolts to the crankcase and secures the flywheel for bolt
removal/installation.
All 1100
YU-01235
Universal Magneto & Rotor Holder
Universal
YB-06117
YB-06117-8
Universal Heavy Duty Puller
Heavy Duty Puller Bolts 8mm
WR/WJ500
YW-06842
Fuel Pressure Gauge Adapter
FX140,
SR230
It attaches between the fuel pump and injector rail when used
with fuel pressure gauge.
WATERCRAFT
YW-41528
All 760,
All 800,
All 1200135 hp
All 1200155 hp
63
WATERCRAFT
Part#
Description/Use
Application
YW-42087
Carburetor Pop-off Pump
Universal,
All
Carburated
It is used to determine pop-off pressure of the needle
and seat.
YU-38407
Oil Temperature Probe
YW-45959
Oil Extractor
It is used for changing oil on four-stroke watercraft (two
gallon capacity, hand-pump action, and no electricity
needed). Easy to dispose of old oil.
YW-06365
Coupler Wrench
WATERCRAFT
It is used to remove the coupler from the engine or
intermediate shaft.
YW-06546
Coupler Wrench
It is used to remove the coupler from the engine or
intermediate shaft.
YW-06551
Coupler Wrench
It is used to remove the coupler from the engine or
intermediate shaft.
YW-38741
Coupler Wrench
It is used to remove the coupler from the engine or
intermediate shaft.
YW-06355
Coupler Shaft Holder
It holds the intermediate shaft for coupler removal.
64
FX140,
FX Cruiser,
SR230
Wave
Runner/
Wave
Jammer
1100
&1200,
All 760,
All 1200135 hp
All 800,
All 1200155hp,
FX140
SJ650 &
Wave Runner
III, All 700
Wave Runner/
Wave Jammer
WATERCRAFT
Part#
YB-06049
YW-38742
Description/Use
Impeller Shaft Holder
Coupler Shaft Holder
They hold the intermediate shaft for coupler or impeller
removal.
YB-06079-A
Impeller Shaft Holder
It holds the drive shaft for impeller removal.
YB-06151
Impeller Shaft Holder
It holds the drive shaft for impeller removal.
YB-06552
Coupler Shaft Holder
It holds the intermediate shaft for coupler removal.
Application
SJ650 &
Wave
Runner III,
All 700,
760, 800,
1200-135hp
Wave
Runner/
Wave
Jammer
III
FX140,
XRT1200,
All 1200155hp
YW-41212
Steering Cable Locknut Remover
YW-06356
Bearing & Seal Installer
Wave
Runner/
Wave
Jammer
YW-06364
Center Drive Shaft Bearing Remover
Wave
Runner/
Wave
Jammer
WRA650
WATERCRAFT
All 800,
All
1200,
FX140,
FX140
Cruiser
65
WATERCRAFT
WATERCRAFT
Part#
Description/Use
Application
YW-06777
Peak Volt Test Lead
All 1100,
All 1200135hp
YW-06778
Peak Volt Test Lead
All 1100,
All 1200135hp
YW-06779
Peak Volt Test Lead
All 760,
All 800
YW-06780
Peak Volt Test Lead
All
1200155hp
YW-06862
ECM Power Coupler
FX140,
SR230
It is used to supply power to the ECM for diagnostic testing.
When using this tool, the ECM is powered, but the fuel pump
is not.
YB-06792
ECM Test Harness
It is used to measure the ECM supply and output voltage.
YB-06791
Pulse Coil Test Harness
YB-06770
Lighting Coil Test Harness
It is used to measure the pulse coil peak voltage output.
It is used to measure the lighting coil peak voltage output.
YB-06790
Regulator/Rectifier Test Harness
YB-06585
Dial Gauge Stand Set
It is used to measure regulator voltage.
It is used to determine crankshaft top dead center for cam
timing or valve adjustement.
YB-01426
YB-04115
Oil Filter Wrench
Cam Wrench
It is used to make minor engine rotations for cam timing or
valve adjustment.
66
FX140,
SR230
s
shop equipmenT
SHOP EQUIPMENT
Part#
Description/Use
Application
YB-35956-A
Lower Unit Pressure/VacuumTester
All
The hand pump device provides both pressure and vacuum for
leak testing of the lower unit.
YB-06117
Universal Puller
All
Heavy duty puller for removing flywheels, balancers and
propeller shaft bearing housings.
YB-06219
YB-22912-1
YU-35557
Bearing Splitter Plates
Using these special splitter plates can solve many difficult
bearing pulling problems, especially where access to the inner
race is limited. “Knife-like” edges may be forced behind the
bearing for a firm grip.
Bearing Splitter Plates
SHOP EQUIPMENT
Using these special splitter plates can solve many difficult
bearing pulling problems, especially where access to the inner
race is limited. “Knife-like” edges may be forced behind the
bearing for a firm grip.
YM-08037
Piston Ring Compressor
Small
Up to 2-1/4”
All
Allows you to compress the rings while installing piston.
54 - 127mm diameter.
YB-06096
Slide Hammer
All
Contains most necessary attachments to remove seals,
bearings and bearing cups.
YB-06523
Bearing Puller Legs
Used with Slide Hammer YB-06096 to be used for removing
bearing cups and seals.
68
Large
Up to 4-1/4”
All
SHOP EQUIPMENT
Part#
Description/Use
Application
YU-01235
Universal Magnet & Rotor Holder
All
Used to loosen and tighten flywheel nuts.
YB-06334
Bearing Puller Legs
Has a wide grip area. Use with Slide Hammer YB-06096.
YU-33277-B
Panasonic Timing Light
This timing light has a bright strobe for outdoor use.
YE-62001-B
K&L Four Gas Analyzer
Used to check emissions output from the engine.
Bridge Two Gas Analyzer
All
Engines
4-Strokes
4-Strokes
Used to check emissions output from the engine.
YE-62001-D
Bridge Four Gas Analyzer
SHOP EQUIPMENT
YE-62001-C
All
Engines
Used to check emissions output from the engine.
YU-01256
Spark Plug Hole Stand
All
Used to set engine on TDC so that the timing position can be
adjusted properly.
69
SHOP EQUIPMENT
Part#
YU-44456
Description/Use
Vacuum Mate Carb Sync Gauge
Application
4-Strokes
A new tool for performing synchronization of carbs and
throttle plates.
YU-44456-10 Carb Sync Tool 6 Cylinder Adapter
F200/225
Used with YU-44456. Vacuum Mate carb sync gauge allows
the vacuum points of all 6 cylinders to be hooked up.
Also requires 2 point taps YU-44456-6.
YU-44456-5
YU-44456-6
5mm Port Taps, Vacuum Mate
6mm Port Taps, Vacuum Mate
4-Strokes
Replacement taps for Vacuum Mate carb sync gauge
YU-44456. Also requires two YU-44456-10.
YU-A5400
Digital Vernier Calipers
All
SHOP EQUIPMENT
LCD display makes for easy reading. Gives exact
measurements to .0005” (.01mm) and features Zero-set at any
point to make measurement of tolerances easier. Reads in
inches or millimeters and will convert. Includes a fitted case
and battery.
YU-03005
Vernier Calipers, 0-200mm
YU-03006
YU-03007
YU-03008
YU-03009
Micrometer 0 - 25mm
Micrometer 25 - 50mm
Micrometer 50 - 75mm
Micrometer 75 - 100mm
YU-03016
YU-03017
Cylinder Bore Gauge 18 - 35mm
Cylinder Bore Gauge 35 - 80mm
Cylinder bore gauges come complete with handle,
dial indicator and set of contact extensions in a handsome
wooden box.
70
All
For inside, outside and depth measurements. Read directly
from highly accurate scale (not from a dial). Includes storage
pouch.
All
All
SHOP EQUIPMENT
Part#
Description/Use
Application
YU-34481
Magnetic Flex Stand
All
Used to accomadate backlash measurements and runout.
YU-05000-B
Snap Ring Pliers
All
This set is used for internal and external snap rings with an
effective range of 10-50mm.
Time-Sert Thread Repair
All
Time-serts are a solid bushing insert. This guarantees easy
installation and allows for full load use of a tapped hole, ensuring
protection against stress and vibration. Time-serts are thin-walled
due to synchronized internal/external threads. A thin cross
sectional area allows for installation in areas of limited space
and clearance material. Time-serts are self-locking. On installation,
the bottom internal threads of the insert are cold rolled to expand
the mating external threads into the base material locking
the insert in place.
Kit 14 x 1.25 (do not contain inserts)
Replacement Serts 11mm Long 5pk.
Replacement Serts 13.5mm Long 5pk.
Kit 12 x 1.25 (do not contain inserts)
Replacement Serts 15mm Long 5pk.
Replacement Serts 9mm long
5pk.
Kit 10 x 1.25 (kit contains 5 inserts 16.2mm long)
Replacement Serts 14mm long
10pk.
Replacement Serts 16.2mm long 10pk.
Kit 8 x 1.25 (kit contains 5 inserts 11.7mm long)
Replacement Serts 11.7mm long 10pk.
Replacement Serts 16.2mm long 10pk.
Kit 6 x 1.0 (kit contains 5 inserts 9.4mm long)
Replacement Serts 9.4mm long 10pk.
Replacement Serts 12mm long
10pk.
Kit 5 x 0.8 (kit contains 5 inserts 7.6mm long)
Replacement Serts 7.6mm long 10pk.
Replacement Serts 10mm long
10pk.
SHOP EQUIPMENT
YU-08001
YU-08001-1
YU-08001-2
YU-08002
YU-08002-1
YU-08002-2
YU-08003
YU-08003-1
YU-08003-2
YU-08004
YU-08004-1
YU-08004-2
YU-08005
YU-08005-1
YU-08005-2
YU-08006
YU-08006-1
YU-08006-2
71
SHOP EQUIPMENT
Part#
Description/Use
Application
YU-A0490
Alden Drill Out Power Extractor Set:
3/4/5/6/8/10/12mm
All
Tough enough to extract grade 8 and 10.9 class stainless steel
bolts, Alden drill-outs feature a “self-centering” tip to
eliminate wandering, even on rough surfaces. Drill-out’s
exclusive two piece design makes removing broken bolts a
fast and simple one step procedure.
YU-A0480
Alden Drill Out Power Extractor Set:
6/8/10/12mm
All
YU-A0485
Alden Micro Drill Out Set:
3/4/5/6mm
All
As effective and fast as the standard size drill-out but with
the drill on one side and the extractor on the other side for
smaller bolts.
YU-A3353
Metric Thread Restorer File
All
Eight different pitches: 0.75mm, 1.00mm, 1.25mm, 1.50mm,
1.75mm, 2.00mm, 2.50mm, & 3.00mm.
YU-A4015
Small Tapered Reamer
All
SHOP EQUIPMENT
It reams holes from 1/8” to 1/2” in diameter.
YU-A4023
Large Tapered Reamer
YU-33211
Antiseize
Saves hardware from corrosion (8 oz. brush top bottle).
72
All
It reams holes from 7/16” to 1” in diameter.
All
SHOP EQUIPMENT
Part#
Description/Use
Application
YU-A9268
Bearing Race & Seal Driver
All
Six discs fit most bearing sizes. To install (drive) seals, turn
discs over. It eliminates damage to bearing races. The seven
piece kit includes a driver handle and the following disc
sizes: 40, 45, 50, 59, 63, and 65mm.
YU-A5399
YU-A9410
Oil Seal Puller with two tips
Oil Seal Puller with adjustable stem
All
Universal seal pullers aid the removal in certain applications.
YE-A9602
Wire and Terminal Center
All
The Wire & Terminal Center from K&L Supply has been
designed with today’s busy service department in mind.
All commonly used electrical connectors and tools can now
be kept in one mobile work station, allowing your technician
to take what is needed to complete a job in one trip. This
fixture rolls on locking casters and will accept rolls of wire
or hose from four to ten inches in diameter with the standard
spindles. One side of the unit holds 20 plastic parts bins, the
other side utilizes pegboard (included) for tool storage.
• 4” swivel casters
• Plastic parts boxes for storage
• Handles 4” and 10” wire spools.
Dimensions: 36” width x 60” height.
Wires and terminals not included.
Feeler Gauge (Standard & Metric)
All
26 tapered blades from .0015” thru .025”.
YU-26900-9
Feeler Gauge-Metric
All
SHOP EQUIPMENT
YU-26900-8
25 blades from 0.04mm thru 1.0mm.
73
SHOP EQUIPMENT
Part#
Description/Use
Application
YU-33223
Compression Gauge
2-Stroke
Includes 12” hose, spark plug hole adapter pressure gauge
and air release quick coupler. It works on all Yamaha
2-stroke outboard motors.
YU-33261-B
Coil Tester
All
Features adjustable spark gap. Allows bench testing of all
Yamaha ignition coils.
YU-34353
Alcohol Detection Kit
All
If an excessive amount of alcohol in the fuel is suspected, this
kit will measure the percentage of alcohol in the fuel in a few
minutes. Includes five liquid transfer pipettes in a plastic
storage case with complete instructions. Additional transfer
pipettes are available by ordering YU-34353-5 (pkg. of 5).
SHOP EQUIPMENT
YU-39951-B
Digital Tachometer
A hand held digital tachometer for monitoring 2-stoke
engines (one through four cylinders) and 4-stroke engines
(one through six and eight cylinders). Just bring the
tachometer near to engine and it will digitally show how fast
the engine is running by counting electric pulses from spark
plug/spark plug cable, and give instantaneous rpm readings.
YU-43700
Accuracy Battery Tester
Accurately tests 6 or 12 volt batteries discharged down to as
low as 1 volt. No time consuming recharging required. Tests
without need to disconnect cables from battery terminals.
Automatically performs two resistive load tests and measures
rate and time of recovery to determine battery condition and
percent of charge. Microprocessor controlled testing is
completed in less than 2 minutes. More accurate than heavy,
cumbersome fixed load carbon pile testers because data
interpretation is eliminated. 3-year warranty, weighs only
2 lbs. Easy to carry, simple to use, fast results. Self powered
with 9-volt battery. Includes molded carrying case and
instructions. Photo not shown.
74
All
All
SHOP EQUIPMENT
Part#
Description/Use
Application
YU-08036-C
#321 Digital Engine Test Tachometer
All
Includes inductive 10’ inductive clip and hanger handle.
SIZE: Approximately 3.375” wide x 4.625” high x 1.250” deep
POWER: (4) AAA 1.5 batteries.
REPLACEMENT PARTS & OPTIONAL ACCESSORIES
YU-08036-C1 Inductive Clip-10 ’
YU-08036-C2 Inductive Clip-20 ‘
YU-08036-C3 Capacitive Clip-2 ‘
YU-08036-C4 Vinyl Storage Case
YE-57000
YE-57001
YE-57002
YE-55102
YE-55101
K&L WC250 Runabout (Complete Unit)
Watercraft Cart only
Watercraft Hoist Arm
Replacement Winch Cable only
Winch & Cable
WC
YE-23400
20-Ton Hydraulic Press
• All Welded Steel Construction
• Reinforced Head Plates
• 20-ton Power Unit Included
• Made in the U.S.A.
All
SHOP EQUIPMENT
K&L WC250 Runabout combines the features of a
workstation and dolly in one upgradeable unit. The base of
the WC250 system is the cart, which can be converted to an
engine hoist by adding the boom and manual winch package.
With this option installed, your technician can lift up to 700
lbs. without assistance. The WC250 can remove a three
cylinder engine without difficulty, and will handle boats up
to 60 inches wide on its Teflon coated bunks. Two fixed and
two swivel-type casters with zerk fittings make transporting
a customer’s boat to your service department simple and
secure. The base model Runabout can serve as a display
fixture as well, with a blue powdercoat finish that looks good
in any showroom. The WC250 offers you a new way to handle the traditional problems of boat transport and service in
one easy to use system.
75
SHOP EQUIPMENT
Part#
Description/Use
Application
YE-23000
Sand Blast Cabinet
All
Side door opening. Thick 18 gauge steel wall construction
with steel legs. Cabinet is 37” wide x 25” diameter x 59”
height. 24”diameter x 24” height working area. Window
measures 7” x 18”. Uses 110V power. Trigger gun assembly,
14CFM @ 90-100psi. Dust collector-DC1500. Made in USA.
Shipping weight 175 lbs. Note: Foot pedal sold as an option.
YE-23010
Optional Accessories
Foot Control Pedal - Includes hose, 2 barbs,
2 clamps, valve and pedal.
Aluminum Oxide - Fast cutting, hard-13 lbs.
Glass Beads - Light, dust free-10 lbs.
Glass Bead Media - 100/170 grit-50 lbs.
Walnut Shells Media - 20/30 grit-50 lbs.
3 Piece Ceramic Nozzle Kit: 3/64”, includes
1 air jet, 1 air jet washer and 1 allen wrench.
3 Piece Steel Nozzle Kit: 1/4”, includes 1 air
jet, 1 air jet washer and 1 allen wrench.
Recoil Air Hose, 12’ length, yellow
Recoil Air Hose 25’ length,
yellow with swivels
Air Line Filter
YE-23100
Tear-Down Table with Drawer
YE-23001
YE-23002
YE-23003
YE-23004
YE-23005
YE-23006
YE-23007
SHOP EQUIPMENT
YE-23008
YE-23009
YE-23050
YE-23051
Hose Reel (size: 23’ x 5/16”)
Hose Reel (size: 46’ x 3/8”)
These 300 degree swivel hose reels are great for keeping shop
floors neat and lowers the risk of accidents. Can be locked
into position. Has adjustable spring tension. Hoses are
unkinkable and highly flexible. Reusable hose and fitting.
Sold each.
76
All
Use as a combination workbench, tear-down tableand tool
storage facility. Table is adjustable from a height of 37” to 41”
and comes with heavy duty 4” casters (2 rigid & 2 locking
swivel). Table top drains into catch pan located below table
top. Shipping weight: 170 lbs.
All
SHOP EQUIPMENT
Part#
Description/Use
Application
YE-23405
Steel “V” Block Set
All
For precision measuring and straightening operations. Made
from cold rolled steel. (not cast) V blocks measure approx.
1-1/4” x 1-3/4” x 5”. Sold in pairs
YU-22888
YU-25031
2 Jaw Puller
3 Jaw Puller
All
Universal bearing and pulley pullers.
YU-25287
Long 2 Jaw Puller
VALVE GUIDE FLEX-HONES (320 GRIT)
All
All
Flexable hones for use to clean out valve guides.
YM-A9243
YM-A9245
YM-A9244
YM-A9246
YM-A9247
YM-A9248
YU-88000
4.0mm
5.0mm
5.5mm
6.0mm
7.0mm
8.0mm
Flex Hone Oil 1/2 Pint
Carbide cutters are all 1/4” shank, 4” long, with standard
spiral cut for most general purposes.
YE-22305 (A)
YE-22306 (B)
YE-22307 (C)
YE-22308 (D)
YE-22309 (E)
YE-22310 (F)
Flame
Cyl. Ball Nose
Large Egg
Round Tree
Small Egg
Ball
All
SHOP EQUIPMENT
CARBIDE CUTTERS
77
SHOP EQUIPMENT
Part#
Description/Use
Application
YE-23011
YE-23012
YE-23013
4” Nozzle Blowgun
20” Nozzle Blowgun
3 pc. Rubber Tip Kit
All
Use with shop air supply.
YU-35759-A
Neway PU1800 Power Unit
The PU1800 Power Unit rolls along a bench-mounted track to
quickly position over the valve seat. No time is lost leveling
or locking down the head. The power unit’s double universal
joint transmission easily adjusts to any cylinder head shape.
The PU1800 Power Unit includes a motor, transmission,
trolley & track, and a foot switch. Note: Head stands not
included.
YM-A9376
Neway Cylinder Head Stand
4-Strokes
4-Strokes
Used to hold cylinder heads while reconditioning valve seats
and guides. Sold in pairs. Pictured with YU-35759-A
Photo not shown.
SHOP EQUIPMENT
YM-A9370
Neway Easy-Turn Wrench
YE-23450
Adjustable Cylinder Head Stand
4-Strokes
The Adjustable Cylinder Head Stand can be used to rotate the
head 360 degrees. Stays in any position using a simple
locking mechanism. Shipping weight: 14 lbs. Adjustable
Length-10 1/2” to 20 1/2” long x 14” width x 10 3/4” high.
YE-23460
Cylinder Head Stands
Cylinder head stands make the cylinder head easier to work
on. Sturdy stands will hold head safely and securely. The
stand is rigid on even surfaces. Tapered pins fit any size
cylinder head bolt hole. Sold in pairs.
78
4-Strokes
The Easy-Turn Wrench helps you get more out of your
Neway Valve Seat Cutters. This handy accessory enables you
to keep the cutter turning continuously so the seats are
finished faster. Comfortable to use, the Easy-Turn Wrench
allows you to feel the amount of material being removed.
4-Strokes
SHOP EQUIPMENT
Part#
Description/Use
Application
YM-A8998
Valve Lapping Tool
4-Strokes
The Valve Lapping Tool is the ultimate vacuum stick for
insuring perfect surfaces on valves and valve seats.
Interchangeable cups make the unit suitable for use with
virtually any size valve. The set includes vacuum stick and
3/4” and 1/4” diameter rubber cups.
YU-A9374
YU-A9375
Neway Cutting Fluid One Pint Spray Bottle
Neway Cutting Fluid One Gallon Bottle
4-Strokes
Must be used when reconditioning valve seats.
YM-A0309
Clover Valve Lapping Compound
4-Strokes
The world famous green can with the four leaf clover. This
compound kit is for seating valves, mating gears, and
sharpening. It is sold as a kit with coarse 120 grit (roughing)
and 280 fine grit (finishing).
YW-45959
Oil Extractor
Used for changing oil on four-stroke watercraft. Two gallon
capacity. Hand-pump action, and no electricity needed.
Easy to dispose of old oil.
All
SHOP EQUIPMENT
Dial Indicator Gauge with Magnetic Base Stand
2-1/4” Dial Indicator Gauge only, 0” - 2-1/4”
range in .001” increments
YU-26900-12 Metric Dial Indicator
YU-A8438
Magnetic Base Stand only
YU-34481
Flexible Magnetic Dial Indicator Stand
YU-A8421
YU-A8428
4-Strokes
79
SHOP EQUIPMENT
Part#
Description/Use
Application
YE-43937
Optimate III Battery Charger
All
The battery charger automatically tests flat batteries for
sulfated condition and, if necessary, applies a special high
voltage (max 22 volts) recovery action. It features a five stage
charging program with constant current, recharges batteries
discharged to as low as +/-2v even after a year of neglect, and
an interactive charging program reverts to bulk charge stage.
In addition, it has an unique 30 minute timer-controlled charge
verification stage and an unique 30 minute timercontrolled check for self-discharge tendency. There is a
comp-rehensive selection of accessories for every need. Lastly,
it has a complete automatic protection against every user error.
YE-63070
Christie Shop Battery Charger
All
This battery charger is specifically designed for personal
watercraft and motorcycle batteries. This Shop unit charges 6
volt and 12 volt batteries with a maximum output of 10 amps.
Enough leads are included to charge up to 10 batteries at
once. All 10 charging circuits are individually fuse protected
to prevent damage. AC input is 115v/60Hz.
YE-63071
Replacement Cables with Clamps
YE-63072
Receptacle Repair Kit
(Sold in pk/ 5)
(includes: 5 receptacle plugs [molex connectors] and
10 female pins for repair of receptacle)
SHOP EQUIPMENT
YE-43934
80
Battery Mate Charger
This battery charger is a combination load tester and
powerful constant current charger with automatic desulfating
action. It features six load test choices, 15A to 150 Amps, for
all batteries from 2.5Ah to 45Ah, and six constant current
settings from 1A to 9A for correct, most time-effective
charging. An optional wall mount is also available to save
bench space.
YE-43935
Optional Wall Mount Bracket
All
SHOP EQUIPMENT
Part#
Description/Use
Application
YU-45826
Optimate PRO 8
All
Dealers can recover, charge and test up to eight batteries
simultaneously with the Optimate PRO 8. The unit is
intended for all types of 12 Volt batteries, including lead-acid,
sealed and gel cell batteries. Battery status monitors are
included at all eight stations, with a special automatic
recovery mode for batteries as deeply-discharged as two
volts. The PRO 8 also has automatic protection against
short-circuits and reverse-polarity connections. Batteries are
charged at 1.2 Amp constant-current charge, with a float
charge when complete to keep the batteries at full capacity.
An optional wall mount is also available to save bench space.
YE-43935
Optional Wall Mount Bracket
YU-03036
Battery Hydrometer
All
Used to check the battery specific gravity.
YU-A1927
Fluke Model 88 Multimeter with Tachometer
All
YU-03112-C
Analog Multimeter
18 meter ranges performs these tests: D.C.V .0 - 5, 25, 125,
500V (20,000 Ohms/Y), A.C.V .0 - 10, 50, 250, 1,000V, D.C.A .
0 - 50A, 0- 250MA, 2.5A, Resistance: 0-2K-20K-2Meg (center
scale 24), Continuity: Test Electric Buzzer (1.5ohms) Includes:
All test leads.
All
SHOP EQUIPMENT
This multimeter’s features include volt, ohm, amp, continuity
and diode tests, rpm measurements with the provided
inductive pickup, minimum/maximum/average recording of
measurements, frequency and duty cycle measurements,
low-ohms function, millisecond pulse width measurements,
and smoothing (shows an averaged reading of measurements
which fluctuate such as rpm). Included accessories: holster,
inductive pickup, hard carrying case, test leads, test probes,
large alligator clips, users manual and quick reference guide.
81
SHOP EQUIPMENT
Part#
Description/Use
Application
YU-A1093
T-Handle Socket Kit
All
Includes: 8/10/12/13/14/17 and 19mm. T-Handle features
include chrome vanadium tool steel deep six point sockets
with a carbon steel T-style handle. It is finished in nickelpewter. The deep sockets allow for nuts to be driven over
long threaded bolts. Individual
Note: Individual T-Handle sizes available, sold each.
YU-A1067
YU-A1068
YU-A1069
YU-A1072
YU-A1073
YU-A1074
YU-A1087
YU-A1104
8mm
10mm
12mm
13mm
14mm
17mm
19mm
T-Handle Rack (10 slots)
YU-05021
YU-05023
YU-05024
YU-05025
T-Handle Screwdriver Medium
T-Handle Screwdriver Large (Regular)
T-Handle Screwdriver Medium (Regular)
T-Handle Screwdriver Small (Regular)
All
SHOP EQUIPMENT
Photos not shown.
82
YU-A0558
Hex T-Handle Set
Includes: 2/2.5/3/4/5/6/8 and 10mm This eight piece set is
in graduated lengths from 2-10mm. Plastic coated, tapered,
cushion grip handles make for easy and comfortable use.
YU-A0559
YU-A0560
YU-A0561
YU-A0562
YU-A0563
YU-A0564
YU-A0565
YU-A0566
2mm Handle sold each
2.5mm Handle sold each
3mm Handle sold each
4mm Handle sold each
5mm Handle sold each
6mm Handle sold each
8mm Handle sold each
10mm Handle sold each
All
SHOP EQUIPMENT
Part#
Description/Use
Application
YU-A0567
Metric Ball Hex Key Set
All
Nine sizes: 1.5, 2, 2.5, 3, 4, 5, 6, 8, and 10mm with plastic
holder. Keys are designed with a ball profile on the long arm.
This feature provides 360˚ of rotation at up to a 30˚ angle.
YU-A0568
Torx Key Set
All
This eight piece set consists of:
T9/T10/T15/T20/T25/T27/T30 & T40, high quality, black
coated “L” wrenches with torx on both ends.
YU-25359-A
Eight Piece Torx Bit Set
All
This set is used for the removal and installation of a
tamper-resistant torx fastener.
YE-31000
Electrical Connector Pin Removal Set
All
Four Piece Pin Set includes the following: 07JA2-002010A,
07JA2-002040A, 07JA2-002060A, 07JA2002070A, precision pin
tools for terminal repair on harness connectors. It safely
removes pins without damaging wires.
Pin Tool A 07JA2-002010A sold each
Pin Tool B 07JA2-002040A sold each
Pin Tool F 07JA2-002060A sold each
Pin Tool G 07JA2-002070A sold each
YE-32210
Terminal Removal Tool
SHOP EQUIPMENT
YE-31001
YE-31002
YE-31003
YE-31004
All
This tool is designed to remove wires from terminals without
damaging the end prongs. Includes six different shaped blades.
83
SHOP EQUIPMENT
Part#
Description/Use
Application
YE-A8535
25’ Automatic Hose Reel
All
Hose withdraws freely from reel and retrieves quickly and
positively. Ratchet holds hose at any desired length until
released. Easily installed on ceiling, wall or floor in any
central position.
YE-A8348
Portable Sand Blast Cabinet
All
Thick wall plastic construction. Cabinet is 30”wide x 20”
diameter x 26” height. Window measures 24” x 14”. Uses
110V power. Trigger gun assembly, 5CFM @ 80-90psi.
Dust collector-5 gallon dust vac. Made in U.S.A. Shipping
weight 38 lbs.
All
YE-23008
YE-23009
YE-23010
Optional Accessories
Foot Control Pedal - Includes hose, 2 barbs,
2 clamps, valve and pedal
Aluminum Oxide - Fast cutting, hard-13 lbs.
Glass Beads - Light, dust free-10 lbs.
Glass Bead Media - 100/170 grit-50 lbs.
Walnut Shells Media - 20/30 grit-50 lbs.
3 Piece Ceramic Nozzle Kit: 3/64”, includes
1 air jet, 1 air jet washer and 1 allen wrench
3 Piece Steel Nozzle Kit: 1/4”, includes 1 air
jet, 1 air jet washer and 1 allen wrench
Recoil Air Hose, 12’ length, yellow
Recoil Air Hose 25’ length, yellow with swivels
Air Line Filter
YE-A4327
Ultra Sonic Parts Cleaner with Heater
All
YE-23001
YE-23002
YE-23003
YE-23004
YE-23005
YE-23006
SHOP EQUIPMENT
YE-23007
Hands-free cleaning- saves time & money.
Safe for the environment, use with a non toxic, water based
cleaning solution. Meets all regulator compliance controls.
Effectively cleans hard to reach areas, blind holes. Unit
includes cover, 60 minute timer, 1 quart UL Super
Concentrate Solvent, drain and hose. Power: 110V, 1.2 amp.
Made in U.S.A.
Overall dimensions:
10.5” length x 7.5” width x 10”depth.
Tank dimensions, inside diameter 6” length x 9” width. Tank
Capacity: 1 qt. Use this for single and twin carbs, fuel injectors and other small components.
YE-A9124
84
Optional Basket for YE-A4327
SHOP EQUIPMENT
Part#
Description/Use
Application
YE-A9149
Ultra Sonic Cleaning Solution
All
One quart container. Makes 10-16 gallons of environmentally
safe, biodegradable, multi-purpose cleaning solution.
YE-A9194
Ultra Sonic Cleaning Solution
One gallon container. Makes 41 gallons of
environmentally safe, biodegradable, multi-purpose
cleaning solution.
YE-A9816
Manual Bearing Packer
All
Packs 50 to 60 bearings without refilling. Use it on all cage-type
roller or ball bearings up to 2” bore. No air line or grease gun
required. Use it to flush out old grease with new.
YE-A9806
Universal Bearing Packer
All
A fast simple way of applying grease to bearings. Just place
bearing between plastic cones, tighten and apply grease
through fitting on end of threaded shaft. Forces out old
grease and evenly injects fresh grease.
YE-A9042
Fluid Evacuator
All
YE-A4777
Deluxe Barrel Pump
All
SHOP EQUIPMENT
The Fluid Evacuator is a portable, hand operated transfer
system with a 6.5 liter (1.7 gallon) capacity. The reservoir is
made of polyethene and can safely hold oil, coolant, and
brake fluid.
• Adjusts to quarts or liters per single stroke
• No drip recovery
• Eliminates messy oil drums
• Includes Telescoping suction tube
• Smooth, easy pump action
• For oils, fuels and non-corrosive solvents
85
SHOP EQUIPMENT
Part#
Description/Use
Application
YE-A8362
Drum Funnel, Yellow (top of photo)
All
Eliminate overspills while pouring. Large surface area
permits drainage of multiple containers simultaneously.
Highly durable, it will resist rust, dents and other chemicals
and give many years of troublefree service. Fits all types of
55 gallon drums.
YE-A8366
Spill Pan, Black (bottom of photo)
All
8” height x 32-1/2” diameter Spill Pan is constructed of
heavy-duty polyethylene that will resist rust, dents and fluids
or chemicals. Catches small drips, leaks or spills that could
make your work area unsafe or hazardous. The Spill Pan is
octaganol in shape and will hold 5 gallons of spilled liquid.
YU-A8840
K&L Deluxe Shop Apron
Made of quality blue cloth with K&L logo imprinted in
yellow on front. Storage pockets included.
SHOP EQUIPMENT
YE-A3919
YE-A3920
YE-A3921
YE-A3968
All
Spout only, no cap. Fits the above Oil Filler Cans.
YU-A4061
YU-A4062
Ratio Rite Measuring Cup
Lid for Ratio Rite
All
Measures in ounces and cc’s. Use for filling forks, shocks,
engine oil, etc. Also has mixing ratio scale for accurate
oil/gas premix. Sold each. Note: Lid is an add-on, not
included with Ratio Rite.
YU-A3917
YU-A3918
86
Oil Filler Can, 1 liter
Oil Filler Can, 2 liter
Oil Filler Can, 5 liter
Replacement Oil Filler Can Spout.
All
Plastic Graduated Cylinder 500cc
Plastic Graduated Cylinder 250cc
All
SHOP EQUIPMENT
Part#
Description/Use
Application
All
CYLINDER FLEX-HONE
For fast and efficient deglazing and final finish honing of cylinder walls. Globules of
silicone carbide laminated to the ends of high density bristles provide a consistent
cross-hatch pattern for oil retention and instant ring seating. Available in the
following grit and sizes:
180 GRIT SIZE
(Recommend for chrome rings)
YU-A9131 36 ~ 38mm I.D
YU-A9132 39 ~ 45mm I.D
YU-A9133 46 ~ 51mm I.D
YU-A9136 52 ~ 57mm I.D
YU-A9145 58 ~ 64mm I.D
YU-A9138 65 ~ 70mm I.D
YU-A9140 71 ~ 76mm I.D
YU-A9141 77 ~ 83mm I.D
YU-A9142 84 ~ 89mm I.D
YU-A9229 90 ~ 95mm I.D
YU-A9230 96 ~ 105mm I.D
YU-A9156
240 GRIT SIZE
(Recommend for moly rings)
YU-A9231
36 ~ 38mm I.D.
YU-A9232
39 ~ 45mm I.D.
YU-A9233
46 ~ 51mm I.D.
YU-A9234
52 ~ 57mm I.D.
YU-A9235
58 ~ 64mm I.D.
YU-A9236
65 ~ 70mm I.D.
YU-A9237
71 ~ 76mm I.D.
YU-A9238
77 ~ 83mm I.D.
YU-A9239
84 ~ 89mm I.D.
YU-A9240
90 ~ 95mm I.D.
YU-A9241
96 ~ 105mm I.D.
Multi Deburring Tool
All
Comes with five blades that are stored in the lightweight
plastic handle. The blades are easily changed by depressing
the locking button. Also useful for chamfering of small holes
in metal.
10mm T-Handle Spark Plug Wrench
12mm T-Handle Spark Plug Wrench
14mm T-Handle Spark Plug Wrench
All
SHOP EQUIPMENT
YU-A6375
YU-A6411
YU-A6410
87
INDEX
YB-01426 . . . . . . . . . . 66
YB-01611. . . . . . . . . . . 24, 52
YB-01619 . . . . . . . . . . 10, 15
YB-01620 . . . . . . . . . . 26
YB-01621 . . . . . . . . . . 21, 31
YB-01624 . . . . . . . . . . 37, 55
YB-01626 . . . . . . . . . . 40
YB-01631 . . . . . . . . . . 37, 57
YB-04019 . . . . . . . . . . 30
YB-04115. . . . . . . . . . . 66
YB-06014 . . . . . . . . . . 8
YB-06015 . . . . . . . . . . 9
YB-06016 . . . . . . . . . . 9, 37
YB-06021 . . . . . . . . . . 9, 21
YB-06022 . . . . . . . . . . 11, 16
YB-06023 . . . . . . . . . . 9
YB-06025 . . . . . . . . . . 8
YB-06027 . . . . . . . . . . 8
YB-06028 . . . . . . . . . . 9
YB-06029 . . . . . . . . . . 8, 16, 22
YB-06029-4 . . . . . . . . . 6, 43
YB-06048 . . . . . . . . . . 43, 57
YB-06049 . . . . . . . . . . 24, 55, 65
YB-06052 . . . . . . . . . . 1, 40, 56
YB-06063 . . . . . . . . . . 17, 26-27,
32, 52-53
YB-06071 . . . . . . . . . . 4, 8-11,
15-17,
20-22,
24-27,
31-32, 34,
37-44,
52-58
YB-06075 . . . . . . . . . . 22
YB-06078 . . . . . . . . . . 11, 21
YB-06079 . . . . . . . . . . 31, 52
YB-06079-A . . . . . . . . 15, 21, 65
YB-06081 . . . . . . . . . . 10, 21
YB-06082 . . . . . . . . . . 16, 21
YB-06085 . . . . . . . . . . 10, 16,
21, 44
YB-06096 . . . . . . . . . . 9, 38, 40,
68-69
YB-06104 . . . . . . . . . . 8
YB-06105 . . . . . . . . . . 20
YB-06106 . . . . . . . . . . 20
YB-06107 . . . . . . . . . . 20, 62
YB-06109 . . . . . . . . . . 44, 54
YB-06110. . . . . . . . . . . 17, 24,
32, 53
YB-06111. . . . . . . . . . . 17, 25,
31, 52
YB-06112. . . . . . . . . . . 16, 25,
31, 54
YB-06117. . . . . . . . . . . 10, 15, 22,
39, 44,
63, 68
YB-06117-8 . . . . . . . . . 63
YB-06139 . . . . . . . . . . 4, 63
YB-06151 . . . . . . . . . . 26, 55, 65
YB-06152 . . . . . . . . . . 26, 53
YB-06153 . . . . . . . . . . 26, 53
88
YB-06155 . . . . . . . . . . 25, 27,
54-55
YB-06156 . . . . . . . . . . 27, 54
YB-06167 . . . . . . . . . . 9, 22
YB-06168 . . . . . . . . . . 8, 15, 22,
31, 44
YB-06169 . . . . . . . . . . 8, 22
YB-06175-2B. . . . . . . . 18, 27, 32,
45-46, 58
YB-06175-C . . . . . . . . 45
YB-06178 . . . . . . . . . . 9
YB-06181 . . . . . . . . . . 4
YB-06194 . . . . . . . . . . 38-39,
56-57
YB-06195-A . . . . . . . . 38, 58
YB-06196 . . . . . . . . . . 38, 58
YB-06199 . . . . . . . . . . 56
YB-06199-A . . . . . . . . 38
YB-06200 . . . . . . . . . . 38, 55
YB-06201 . . . . . . . . . . 39
YB-06202 . . . . . . . . . . 34
YB-06205 . . . . . . . . . . 34
YB-06207 . . . . . . . . . . 39
YB-06213 . . . . . . . . . . 38-39, 43,
56-57
YB-06219 . . . . . . . . . . 68
YB-06228 . . . . . . . . . . 10
YB-06229 . . . . . . . . . . 4, 8-11,
15-16,
20-21, 24
YB-06230 . . . . . . . . . . 10-11
YB-06231 . . . . . . . . . . 10-11, 16
YB-06234 . . . . . . . . . . 10, 15, 22
YB-06240 . . . . . . . . . . 34
YB-06244 . . . . . . . . . . 34, 55
YB-06246 . . . . . . . . . . 40
YB-06258 . . . . . . . . . . 40
YB-06261 . . . . . . . . . . 40
YB-06265 . . . . . . . . . . 1, 4
YB-06269 . . . . . . . . . . 26, 53
YB-06270-A . . . . . . . . 17, 25,
31, 53
YB-06276 . . . . . . . . . . 54
YB-06276-A . . . . . . . . 31
YB-06276-B. . . . . . . . . 16, 27,
44, 54
YB-06277-A . . . . . . . . 25
YB-06283 . . . . . . . . . . 35
YB-06287 . . . . . . . . . . 20
YB-06298 . . . . . . . . . . 15
YB-06299 . . . . . . . . . . 15, 21
YB-06308 . . . . . . . . . . 14
YB-06320 . . . . . . . . . . 30, 51
YB-06334 . . . . . . . . . . 69
YB-06335 . . . . . . . . . . 38
YB-06336 . . . . . . . . . . 41
YB-06337 . . . . . . . . . . 42, 57
YB-06338 . . . . . . . . . . 42
YB-06339 . . . . . . . . . . 42
YB-06344 . . . . . . . . . . 15, 23
YB-06345 . . . . . . . . . . 24
YB-06346 . . . . . . . . . . 20, 24
YB-06347 . . . . . . . . . . 24
YB-06348 . . . . . . . . . . 24
YB-06349 . . . . . . . . . . 20
YB-06368 . . . . . . . . . . 22
YB-06376 . . . . . . . . . . 39, 56
YB-06377 . . . . . . . . . . 39, 56
YB-06378 . . . . . . . . . . 39, 56
YB-06400 . . . . . . . . . . 23
YB-06430 . . . . . . . . . . 43, 57
YB-06431 . . . . . . . . . . 43
YB-06432 . . . . . . . . . . 44
YB-06433 . . . . . . . . . . 42
YB-06434 . . . . . . . . . . 43
YB-06435 . . . . . . . . . . 43
YB-06436 . . . . . . . . . . 42
YB-06437 . . . . . . . . . . 42
YB-06439 . . . . . . . . . . 42, 44
YB-06439-2 . . . . . . . . . 45
YB-06440 . . . . . . . . . . 43
YB-06440-A . . . . . . . . 1, 45
YB-06441 . . . . . . . . . . 43
YB-06441-3 . . . . . . . . . 45
YB-06442 . . . . . . . . . . 37
YB-06443 . . . . . . . . . . 20
YB-06520 . . . . . . . . . . 57
YB-06523 . . . . . . . . . . 68
YB-06544 . . . . . . . . . . 46, 59
YB-06548 . . . . . . . . . . 45-46,
58-59
YB-06552 . . . . . . . . . . 49, 65
YB-06554 . . . . . . . . . . 49
YB-06562 . . . . . . . . . . 49
YB-06569 . . . . . . . . . . 46, 58-59
YB-06572 . . . . . . . . . . 46, 58-59
YB-06578 . . . . . . . . . . 45
YB-06580 . . . . . . . . . . 46
YB-06581 . . . . . . . . . . 46, 59
YB-06585 . . . . . . . . . . 66
YB-06757 . . . . . . . . . . 1
YB-06766 . . . . . . . . . . 1, 36, 50
YB-06767 . . . . . . . . . . 1, 48
YB-06768 . . . . . . . . . . 1
YB-06769 . . . . . . . . . . 1
YB-06770 . . . . . . . . . . 1, 48, 66
YB-06771 . . . . . . . . . . 1
YB-06772 . . . . . . . . . . 1
YB-06776 . . . . . . . . . . 45, 59
YB-06787 . . . . . . . . . . 1
YB-06788 . . . . . . . . . . 1
YB-06790 . . . . . . . . . . 1, 50, 66
YB-06791 . . . . . . . . . . 1, 50, 66
YB-06792 . . . . . . . . . . 1, 50, 66
YB-06793 . . . . . . . . . . 1, 51
YB-06795 . . . . . . . . . . 1, 35, 50
YB-06801 . . . . . . . . . . 30, 48, 51
YB-06810 . . . . . . . . . . 51
YB-06857 . . . . . . . . . . 35, 49
YB-06861 . . . . . . . . . . 37, 51
YB-06867 . . . . . . . . . . 30, 36
YB-06868 . . . . . . . . . . 14, 30, 36
YB-06869 . . . . . . . . . . 36, 50
YB-06870 . . . . . . . . . . 35
YB-06871 . . . . . . . . . . 48, 51
YB-06872 . . . . . . . . . . 49
YB-06879 . . . . . . . . . . 36
YB-06887 . . . . . . . . . . 37, 51
YB-06888 . . . . . . . . . . 36
YB-07003 . . . . . . . . . . 4, 6
YB-22912-1 . . . . . . . . . 68
YB-34232-C . . . . . . . . 11, 23
YB-34432-15 . . . . . . . . 23
YB-34432-97 . . . . . . . . 41
YB-34432-C . . . . . . . . 23
YB-34432-D . . . . . . . . 1, 5
YB-34446 . . . . . . . . . . 1, 5
YB-34447 . . . . . . . . . . 27, 38, 52
YB-34449-A . . . . . . . . 40
YB-34453 . . . . . . . . . . 40
YB-34465 . . . . . . . . . . 5
YB-34466 . . . . . . . . . . 27
YB-34468-2 . . . . . . . . . 25, 56-57
YB-34468-5 . . . . . . . . . 25, 52
YB-34468-A . . . . . . . . 1, 25
YB-34473 . . . . . . . . . . 17, 26-27,
32, 52-54
YB-34474 . . . . . . . . . . 25, 27, 55
YB-35956-A . . . . . . . . 68
YB-37103-10 . . . . . . . . 6
YB-37103-11 . . . . . . . . 6
YB-37103-12 . . . . . . . . 6
YB-37103-13 . . . . . . . . 6
YB-37103-3 . . . . . . . . . 6
YB-37103-4 . . . . . . . . . 6
YB-37103-5 . . . . . . . . . 6
YB-37103-6 . . . . . . . . . 6
YB-37103-8 . . . . . . . . . 6
YB-37103-9 . . . . . . . . . 6
YB-37462 . . . . . . . . . . 34
YB-37463 . . . . . . . . . . 34
YB-38831 . . . . . . . . . . 1, 35,
49, 51
YB-38832 . . . . . . . . . . 1, 35
YB-39799 . . . . . . . . . . 15, 23
YB-39952 . . . . . . . . . . 5
YB-39991 . . . . . . . . . . 35-37,
48-51
YB-41446 . . . . . . . . . . 17, 26,
32, 53
YB-41707 . . . . . . . . . . 44
YB-42223 . . . . . . . . . . 41
YB-42224 . . . . . . . . . . 41
YB-42225 . . . . . . . . . . 41
YB-42227 . . . . . . . . . . 41
YB-42229 . . . . . . . . . . 41
YB-44478 . . . . . . . . . . 1, 36
YB-45544 . . . . . . . . . . 1, 5
YB-45775 . . . . . . . . . . 49
YB-91044 . . . . . . . . . . 5
YE-22305 . . . . . . . . . . 77
YE-22306 . . . . . . . . . . 77
YE-22307 . . . . . . . . . . 77
YE-22308 . . . . . . . . . . 77
YE-22309 . . . . . . . . . . 77
YE-22310 . . . . . . . . . . 77
YE-23000 . . . . . . . . . . 76
YE-23001 . . . . . . . . . . 76, 84
YE-23002 . . . . . . . . . . 76, 84
INDEX
YE-23003 . . . . . . . . . . 76, 84
YE-23004 . . . . . . . . . . 76, 84
YE-23005 . . . . . . . . . . 76, 84
YE-23006 . . . . . . . . . . 76, 84
YE-23007 . . . . . . . . . . 76, 84
YE-23008 . . . . . . . . . . 76, 84
YE-23009 . . . . . . . . . . 76, 84
YE-23010 . . . . . . . . . . 76, 84
YE-23011. . . . . . . . . . . 78
YE-23012 . . . . . . . . . . 78
YE-23013 . . . . . . . . . . 78
YE-23050 . . . . . . . . . . 76
YE-23051 . . . . . . . . . . 76
YE-23100 . . . . . . . . . . 76
YE-23400 . . . . . . . . . . 75
YE-23405 . . . . . . . . . . 77
YE-23450 . . . . . . . . . . 78
YE-23460 . . . . . . . . . . 78
YE-31000 . . . . . . . . . . 83
YE-31001 . . . . . . . . . . 83
YE-31002 . . . . . . . . . . 83
YE-31003 . . . . . . . . . . 83
YE-31004 . . . . . . . . . . 83
YE-32210 . . . . . . . . . . 83
YE-43934 . . . . . . . . . . 80
YE-43937 . . . . . . . . . . 80
YE-55101 . . . . . . . . . . 75
YE-55102 . . . . . . . . . . 75
YE-57000 . . . . . . . . . . 75
YE-57001 . . . . . . . . . . 75
YE-57002 . . . . . . . . . . 75
YE-62001-B. . . . . . . . . 69
YE-62001-C . . . . . . . . 69
YE-62001-D . . . . . . . . 69
YE-63070 . . . . . . . . . . 80
YE-63071 . . . . . . . . . . 80
YE-63072 . . . . . . . . . . 80
YE-A3919 . . . . . . . . . . 86
YE-A3920 . . . . . . . . . . 86
YE-A3921 . . . . . . . . . . 86
YE-A3968 . . . . . . . . . . 86
YE-A4327 . . . . . . . . . . 84
YE-A4777 . . . . . . . . . . 85
YE-A8362 . . . . . . . . . . 86
YE-A8366 . . . . . . . . . . 86
YE-A8535 . . . . . . . . . . 84
YE-A9042 . . . . . . . . . . 85
YE-A9124 . . . . . . . . . . 84
YE-A9149 . . . . . . . . . . 85
YE-A9194 . . . . . . . . . . 85
YE-A9602 . . . . . . . . . . 73
YE-A9806 . . . . . . . . . . 85
YE-A9816 . . . . . . . . . . 85
YM-01122 . . . . . . . . . . 14, 48
YM-01196 . . . . . . . . . . 14, 48
YM-01253 . . . . . . . . . . 4, 49, 51
YM-04015 . . . . . . . . . . 14, 30
YM-04019 . . . . . . . . . . 30, 62
YM-04044 . . . . . . . . . . 63
YM-04064-A. . . . . . . . 50
YM-04066 . . . . . . . . . . 30, 49
YM-04108 . . . . . . . . . . 62
YM-04111 . . . . . . . . . . 62
YM-04112 . . . . . . . . . . 62
YM-04113 . . . . . . . . . . 62
YM-04114 . . . . . . . . . . 62
YM-04116 . . . . . . . . . . 62
YM-04117 . . . . . . . . . . 62
YM-04118 . . . . . . . . . . 62
YM-08035-A. . . . . . . . 14
YM-08037 . . . . . . . . . . 63, 68
YM-34483 . . . . . . . . . . 62
YM-45469 . . . . . . . . . . 62
YM-A0309 . . . . . . . . . 79
YM-A8998 . . . . . . . . . 79
YM-A9243 . . . . . . . . . 77
YM-A9244 . . . . . . . . . 77
YM-A9245 . . . . . . . . . 77
YM-A9246 . . . . . . . . . 77
YM-A9247 . . . . . . . . . 77
YM-A9248 . . . . . . . . . 77
YM-A9370 . . . . . . . . . 78
YS-01880-A . . . . . . . . 37
YU-01235 . . . . . . . . . . 63, 69
YU-01256 . . . . . . . . . . 69
YU-01304 . . . . . . . . . . 62
YU-03005 . . . . . . . . . . 70
YU-03006 . . . . . . . . . . 70
YU-03007 . . . . . . . . . . 70
YU-03008 . . . . . . . . . . 70
YU-03009 . . . . . . . . . . 70
YU-03016 . . . . . . . . . . 70
YU-03017 . . . . . . . . . . 70
YU-03036 . . . . . . . . . . 81
YU-03097 . . . . . . . . . . 6
YU-03112-C . . . . . . . . 81
YU-05000-B . . . . . . . . 71
YU-05021 . . . . . . . . . . 82
YU-05023 . . . . . . . . . . 82
YU-05024 . . . . . . . . . . 82
YU-05025 . . . . . . . . . . 82
YU-05212 . . . . . . . . . . 6
YU-08001 . . . . . . . . . . 71
YU-08001-1 . . . . . . . . 71
YU-08001-2 . . . . . . . . 71
YU-08002 . . . . . . . . . . 71
YU-08002-1 . . . . . . . . 71
YU-08002-2 . . . . . . . . 71
YU-08003 . . . . . . . . . . 71
YU-08003-1 . . . . . . . . 71
YU-08003-2 . . . . . . . . 71
YU-08004 . . . . . . . . . . 71
YU-08004-1 . . . . . . . . 71
YU-08004-2 . . . . . . . . 71
YU-08005 . . . . . . . . . . 71
YU-08005-1 . . . . . . . . 71
YU-08005-2 . . . . . . . . 71
YU-08006 . . . . . . . . . . 71
YU-08006-1 . . . . . . . . 71
YU-08006-2 . . . . . . . . 71
YU-08036-C . . . . . . . . 75
YU-08036-C1 . . . . . . . 75
YU-08036-C2 . . . . . . . 75
YU-08036-C3 . . . . . . . 75
YU-08036-C4 . . . . . . . 75
YU-22888 . . . . . . . . . . 77
YU-25031 . . . . . . . . . . 77
YU-25287 . . . . . . . . . . 77
YU-25359-A . . . . . . . . 83
YU-26900-12 . . . . . . . 79
YU-26900-8 . . . . . . . . 73
YU-26900-9 . . . . . . . . 73
YU-33211 . . . . . . . . . . 72
YU-33223 . . . . . . . . . . 74
YU-33261-B . . . . . . . . 74
YU-33277-B . . . . . . . . 69
YU-34353 . . . . . . . . . . 74
YU-34481 . . . . . . . . . . 4, 6,
71, 79
YU-34898 . . . . . . . . . . 6
YU-35557 . . . . . . . . . . 68
YU-35759-A . . . . . . . . 78
YU-37103-A . . . . . . . . 6
YU-38407 . . . . . . . . . . 64
YU-39951-B . . . . . . . . 74
YU-39991 . . . . . . . . . . 1, 6, 14,
20, 30
YU-43700 . . . . . . . . . . 74
YU-44456 . . . . . . . . . . 70
YU-44456-10 . . . . . . . 70
YU-44456-5 . . . . . . . . 70
YU-44456-6 . . . . . . . . 70
YU-45826 . . . . . . . . . . 81
YU-88000 . . . . . . . . . . 77
YU-A0480. . . . . . . . . . 72
YU-A0485. . . . . . . . . . 72
YU-A0490. . . . . . . . . . 72
YU-A0558. . . . . . . . . . 82
YU-A0559. . . . . . . . . . 82
YU-A0560. . . . . . . . . . 82
YU-A0561. . . . . . . . . . 82
YU-A0562. . . . . . . . . . 82
YU-A0563. . . . . . . . . . 82
YU-A0564. . . . . . . . . . 82
YU-A0565. . . . . . . . . . 82
YU-A0566. . . . . . . . . . 82
YU-A0567. . . . . . . . . . 83
YU-A0568. . . . . . . . . . 83
YU-A1067. . . . . . . . . . 82
YU-A1068. . . . . . . . . . 82
YU-A1069. . . . . . . . . . 82
YU-A1072. . . . . . . . . . 82
YU-A1073. . . . . . . . . . 82
YU-A1074. . . . . . . . . . 82
YU-A1087. . . . . . . . . . 82
YU-A1093. . . . . . . . . . 82
YU-A1104. . . . . . . . . . 82
YU-A1927. . . . . . . . . . 81
YU-A3353. . . . . . . . . . 72
YU-A3917. . . . . . . . . . 86
YU-A3918. . . . . . . . . . 86
YU-A4015. . . . . . . . . . 72
YU-A4023. . . . . . . . . . 72
YU-A4061. . . . . . . . . . 86
YU-A4062. . . . . . . . . . 86
YU-A5399. . . . . . . . . . 73
YU-A5400. . . . . . . . . . 70
YU-A6375. . . . . . . . . . 87
YU-A6410. . . . . . . . . . 87
YU-A6411. . . . . . . . . . 87
YU-A8421. . . . . . . . . . 79
YU-A8428. . . . . . . . . . 79
YU-A8438. . . . . . . . . . 79
YU-A8840. . . . . . . . . . 86
YU-A9131. . . . . . . . . . 87
YU-A9132. . . . . . . . . . 87
YU-A9133. . . . . . . . . . 87
YU-A9136. . . . . . . . . . 87
YU-A9138. . . . . . . . . . 87
YU-A9140. . . . . . . . . . 87
YU-A9141. . . . . . . . . . 87
YU-A9142. . . . . . . . . . 87
YU-A9145. . . . . . . . . . 87
YU-A9156. . . . . . . . . . 87
YU-A9229. . . . . . . . . . 87
YU-A9230. . . . . . . . . . 87
YU-A9231. . . . . . . . . . 87
YU-A9232. . . . . . . . . . 87
YU-A9233. . . . . . . . . . 87
YU-A9234. . . . . . . . . . 87
YU-A9235. . . . . . . . . . 87
YU-A9236. . . . . . . . . . 87
YU-A9237. . . . . . . . . . 87
YU-A9238. . . . . . . . . . 87
YU-A9239. . . . . . . . . . 87
YU-A9240. . . . . . . . . . 87
YU-A9241. . . . . . . . . . 87
YU-A9268. . . . . . . . . . 73
YU-A9374. . . . . . . . . . 79
YU-A9375. . . . . . . . . . 79
YU-A9410. . . . . . . . . . 73
YW-06355 . . . . . . . . . . 48, 64
YW-06356 . . . . . . . . . . 65
YW-06364 . . . . . . . . . . 65
YW-06365 . . . . . . . . . . 64
YW-06546 . . . . . . . . . . 64
YW-06547 . . . . . . . . . . 63
YW-06550 . . . . . . . . . . 63
YW-06551 . . . . . . . . . . 64
YW-06777 . . . . . . . . . . 66
YW-06778 . . . . . . . . . . 66
YW-06779 . . . . . . . . . . 66
YW-06780 . . . . . . . . . . 66
YW-06842 . . . . . . . . . . 63
YW-06862 . . . . . . . . . . 66
YW-38741 . . . . . . . . . . 64
YW-38742 . . . . . . . . . . 65
YW-41212 . . . . . . . . . . 65
YW-41212-2 . . . . . . . . 65
YW-41212-3 . . . . . . . . 65
YW-41528 . . . . . . . . . . 63
YW-42087 . . . . . . . . . . 64
YW-45959 . . . . . . . . . . 64, 79
89
POLICIES & PROCEDURES
HOW TO ORDER:
We offer three convenient ways to order: toll-free phone, fax, or regular mail.
• Toll-Free Phone:
• Fax:
• Mail:
1-800-708-3184
1-408-727-4305
K&L O.E. Division
Yamaha Tool and Equipment Program
Attn: Customer Service
1040 Richard Ave.
Santa Clara, CA 95050
DEALER NUMBER:
This program is only available to authorized Yamaha dealers. Please include your Yamaha Dealer Number on
all correspondence.
TAXES:
State and/or local taxes will be added if applicable.
PAYMENT:
All orders will be billed through Yamaha under your normal billing terms.
FREIGHT:
You may choose from UPS Ground, UPS Next Day Air, UPS 2-Day, or UPS 3-Day. Large, heavy items such as equipment
will be shipped by truck. Shipments will be made F.O.B., Santa Clara, California. Freight charges will be added to your bill.
TECHNICAL SUPPORT:
Technical Support is available by calling toll-free 1-800-708-3184 Monday through Friday, 8:30 a.m. to 4:30 p.m. Pacific time.
DAMAGED SHIPMENTS:
All shipments must be inspected upon delivery for visible signs of damage or possible damage. Have the delivery
person make a note of the damage before you sign for it.
UPS Shipments –You must file a Damage Report with UPS.
Truck Line Shipments – Upon delivery, all damage or possible damage must be noted on the bill of lading.
All cartons, boxes, packaging, etc. MUST be kept for inspection by UPS or Truck Line Inspectors. No damaged parts will
be accepted for return unless UPS or K&L are notified within 48 hours.
SHIPMENT DISCREPANCIES:
All shortages and shipping errors must be reported within 48 hours of delivery. Call or fax our Customer Service
Department. We will assist you in correcting the problem.
NON-WARRANTY RETURNS POLICY:
K&L accepts non-warranty returns as follows (see the separate Warranty Returns Policy for return of defective products):
• Returns must be authorized within 30 days of Yamaha invoice.
• Return shipments must have the Return Authorization Number visible on the outside of the package.
• Product must be in restockable/resaleable condition, free of permanent markings of any type,
and with all original packaging.
• Returns are subject to a 20% restocking fee (no restocking fee if K&L was at fault).
• Closeout, discontinued and essential products are not eligible for return.
90
POLICIES & PROCEDURES
To obtain a Return Authorization Number, call 1-800-708-3184 to talk with a Customer Service Representative.
After receiving a Return Authorization Number, carefully pack and ship the product(s) prepaid to:
K&L O.E. Division
Yamaha Tool and Equipment Program
Attn: Returns Dept.
1040 Richard Ave.
Santa Clara, CA 95050
WARRANTY RETURNS POLICY:
K&L will process all manufacturer warranty claims for the dealer. To initiate a warranty claim, call 1-800-708-3184 to talk
with a Customer Service Representative. Claims usually require the product to be shipped prepaid to K&L for
inspection. If the claim is determined to be valid, you can request a replacement product or a credit on your Yamaha
Parts Account. Replacement products will be shipped free freight at the same service level as the original order
(you can request faster delivery and pay the difference).
LIFETIME WARRANTY:
All Yamaha Specialty Hand Tools come with a limited lifetime warranty. Yamaha Specialty Hand Tools are warranted
against defects in material and workmanship for the life of the product. Life of the product refers to that point in time
when the product no longer functions due to normal wear. K&L will repair or replace, at the option of K&L, any
Yamaha Specialty Hand Tool found to be defective by K&L. In no event shall K&L be held liable for any direct or
consequential damages. This warranty is in lieu of any other warranty, expressed or implied, including (without
limitation) any warranties of merchantability or fitness for a particular purpose.
PASS-THROUGH WARRANTY:
We pass on all warranties made by the manufacturer, who has the sole responsibility for performing such warranties.
The manufacturer shall be solely responsible for any damage to person or property arising from faulty design, materials
and workmanship of its products. K&L accepts no liability for such damages and shall not be held liable for indirect or
consequential damages. K&L makes no warranty as to products distributed by us, expressed or implied, including
(without limitation) any warranties of merchantability or fitness for a particular purpose.
YAMAHA SPECIAL TOOL PART NUMBERS:
Yamaha Service Manuals and other service literature normally list special tools by their "Y" number (such as YM-12345
or YU-12321). Always order tools using this "Y" number, not the "90890" number (such as 90890-12345-00). If a "Y"
number is not listed, contact K&L for ordering assistance.
CATALOG CONTENTS:
To the best of our knowledge, the contents of this catalog are correct. We assume no liability for any errors in regards to
specifications, part numbers, or model application listings. We reserve the right to change specifications, product
descriptions, quality, pricing and model applications at any time and without further obligation.
SPECIAL NOTE:
All printed materials are copyrighted by K&L Supply Company. No part of this publication may be reproduced, stored
in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of K&L Supply Company. The name “Yamaha” and the Yamaha logo
are trademarks and the property of Yamaha Motor Corporation.
91
ORDER FORM
Yamaha Dealer Order Form
Dealer No.
(Fax or Mail this form to K&L Supply)
Date
Time
Purchase Order No.
Red Label
Ground
Blue Label
Other
Orange
SOLD TO:
SHIP TO:
Telephone No.________________________________________
Telephone No.________________________________________
Dealer______________________________________________
Dealer______________________________________________
Street_______________________________________________
Street_______________________________________________
City______________________State__________Zip__________
City______________________State__________Zip__________
Fax No._____________________________________________
Fax No._____________________________________________
Qty.
Part Number
Description
Unit price
Extended
Total
_______________________________________________
Authorized Dealer Signature
Date
Phone 800-708-3184 or Fax 408-727-4305