Sharp XG-P20XUL Operating instructions

Important
Information
Setup & Connections
Operation Buttons
Basic Operation
Multiple Function
OPERATION MANUAL
LCD PROJECTOR
XG-P20XU
Maintenance &
Troubleshooting
MODEL
Appendix
Important
Information
Before using the LCD projector, please read this operation manual carefully.
Introduction
IMPORTANT
For your assistance in reporting the loss or theft of your Color LCD Projector,
please record the Serial Number located on the bottom of the projector and
retain this information. Before recycling the packaging, please be sure that you
have checked the contents of the carton thoroughly against the list of “Supplied
Accessories” on page 12 .
ENGLISH
Model No.: XG-P20XU
Serial No.:
There are two important reasons for prompt warranty registration of your new SHARP LCD Projector, using the REGISTRATION CARD
packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give
under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
See bottom of actual set.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk or
electric shock to persons.
The exclamation point within a triangle is intended
to alert the user to the presence of important
operating and maintenance (servicing) instructions
in the literature accompanying the product.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
U.S.A. ONLY
The enclosed RGB (computer) cable must be used with the device. The cable is provided to ensure that the device complies with FCC
Class A verification.
U.S.A. ONLY
“Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device”.
CANADA ONLY
For GyroRemote unit (RRMCG1631CESA)
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This device operates in the frequency band of 49.82 to 49.90 MHz with RF output power of less than 30 MicroWatts EIRP (Effective Isotropic
Radiated Power).
Caution
Any changes made to this device not expressly approved by the manufacturer could void the users right to operate this device.
E-1
Important
Information
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions. This product has been engineered and manufactured to ensure your
personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to
defeat the safeguards incorporated into this LCD Projector, observe the following basic rules for its installation, use and
servicing. For your own protection and reliable usage of your LCD Projector, please be sure to read these “IMPORTANT
SAFEGUARDS” carefully before use.
1. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained
for future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions
should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a
bathtub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious
injury to a child or adult, and serious damage to the product.
Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the
product. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
9. Transportation
A product and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the product
and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product and
to protect it from overheating. The openings should never
be covered or blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure
of the type of power supply to your home, consult your
product dealer or local power company. For products
intended to operate from battery power, or other sources,
refer to the operating instructions.
12. Grounding or Polarization
This product is equipped with a three-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will
only fit into a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit
from the product.
14. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect
the cable system. This will prevent damage to the product
due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire
or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation.
e. If the product has been dropped or damaged in any
way.
f. If the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
E-2
Important
Information
IMPORTANT SAFEGUARDS
Caution Concerning the Lamp
Replacement
See “Replacing the Lamp” on pages 68 and 69 .
LAMP REPLACEMENT
CAUTION
BEFORE REMOVING THE SCREW, DISCONNECT
POWER CORD. HOT SURFACE INSIDE
ALLOW 1 HOUR TO COOL BEFORE REPLACING
THE LAMP. REPLACE WITH SAME SHARP LAMP
UNIT TYPE BQC-XGP20X//1 ONLY.
UV RADIATION : CAN CAUSE EYE DAMAGE.
TURN OFF LAMP BEFORE SERVICING.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION.
POTENTIAL HAZARD OF GLASS PARTICLES IF
LAMP HAS RUPTURED. HANDLE WITH CARE.
SEE OPERATION MANUAL.
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and high intensity
discharge lamp (HID lamp) containing a small amount of
mercury. Disposal of these materials may be regulated due
to environmental considerations. For disposal or recycling
information, please contact your local authorities or the
Electronics Industries Alliance: www.eiae.org.
Caution Concerning the Lamp Unit
Potential hazard of glass particles if lamp ruptures. In
case of lamp rupture, contact your nearest Authorized
Sharp Industrial LCD Products Dealer or Service Center
for a replacement.
See “Replacing the Lamp” on pages 68 and 69 .
Cautions Concerning the Setup of
the Projector
CAUTION
PRECAUCIÓN
PRÉCAUTION
For minimal servicing and to maintain high image quality,
SHARP recommends that this projector be installed in
an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the lens must be cleaned more often. As long as the
projector is properly maintained in this manner, use in
these environments will not reduce the overall operation
life. Please note that all internal cleaning must be
performed by an Authorized Sharp Industrial LCD
Products Dealer or Service Center.
Notes on Operation
• The exhaust vent, the lamp cage cover and adjacent
areas may be extremely hot during projector
operation. To prevent injury, do not touch these areas
until they have sufficiently cooled.
• Allow at least 4 inches (10 cm) of space between the
exhaust vent and the nearest wall or obstruction.
• If the cooling fan becomes obstructed, a protection
device will automatically turn off the projector lamp.
This does not indicate a malfunction. Remove the
projector power cord from the wall outlet and wait at
least 10 minutes. Then turn on the power by plugging
the power cord back in. This will return the projector
to the normal operating condition.
E-3
Important
Information
IMPORTANT SAFEGUARDS
Temperature Monitor Function
If the projector starts to overheat due to setup problems
or a dirty air filter, “TEMP.” and “ ” will flash in the lowerleft corner of the picture. If the temperature continues
to rise, the lamp will turn off, the TEMPERATURE
WARNING indicator on the projector will flash, and after
a 90-second cooling-off period the power will shut off.
Refer to “Lamp/Maintenance Indicators” on page 67 ,
for details.
• The cooling fan regulates the internal temperature, and its
performance is automatically controled. The sound of the
fan may change during projector operation due to changes
in the fan speed.
Using the Carrying Handle
When transporting the projector, carry it by the carrying
handle on the side.
CAUTION
• Always put on the lens cap to prevent damage to the lens
when transporting the projector.
• Do not lift or carry the projector by the lens or the lens cap
as this may damage the lens.
Using the Kensington Lock
Kensington Security
Standard connector
This projector has a Kensington Security Standard
connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the
system for instructions on how to use it to secure the
projector.
E-4
Important
Information
Outstanding Features
1. High-end LCD Projector with Ultra High Brightness
• AC 220 W Lamp
Use AC 220 W lamp for excellent color uniformity and ultra high brightness.
2. Computer Compatibility
• Compatible with resolutions including VGA-SVGA (expanded), XGA (true
resolution) and SXGA-UXGA (compressed) as well as DTV formats (480i, 480P,
720P and 1080i).
3. XGA Image Quality
• OCS LCD panel enhances color uniformity.
• Various other circuits are also used to provide high quality video images.
4. Computer & Video Integrated Composer Technology
• New Progressive Mode
I/P conversion with new algorithm used to achieve beautiful image quality.
• Enhanced Up-scaling and Digital Image Enlargement
Enables sharper image quality without jaggies even for enlarged images.
• Superior 16:9 Image
4:3 images can be converted to 16:9 images using Smart Stretch (sides stretched,
center untouched), previously not achievable with LCD projectors.
• Intelligent Digital Keystone Correction
Smooths out jaggies on keystone images and compresses the image not only
horizontally but vertically keeping the 4 : 3 aspect ratio, and at the same time, calculates
the aspect ratio automatically adjusting to the lens shift width.
• New Intelligent Compression
Efficiently compresses UXGA (1,600 1,200) images to XGA (1,024 768).
• Enhanced three-two pull down
Converts cinema mode DVD images transformed with three-two pull down enhancement
to progressive mode images for easier viewing by Film Mode.
• Dynamic GAMMA Correction
Optimizing GAMMA correction frame by frame in real time.
5. 3D Digital Uniformity and Digital Convergence
• Three-Dimensional Digital Uniformity compensates uneven picture brightness
even for pictures at any brightness level from white to dark. And, with Digital
Convergence, a slight distortion of convergence can be adjusted on the service
menu screen without having to touch the LCD panel.
E-5
Important
Information
Outstanding Features
6. Network Capability
• Self-Diagnosis/Projector Status
Self-diagnosis/Projector status function sends e-mail
messages to a specified computer about lamp usage
time and any malfunctions.
• Multiple & Group Projector Control
Up to 250 projectors can be controled over a network.
Projector RS-232C OUT can be used for daisy chain
connection.
• Simple Stacking and Videowall Display
Comes with software for easy stacking and videowall processing even for input from a
single source.
7. Four Optional Lenses for Maximum Flexibility
• Bayonet mount type: Wide-Zoom Lens, Tele-Zoom Lens
• Screw mount type: Fixed Wide Lens, Tele-Zoom Lens
8. Multiple Input and Output Terminals
• BNC Terminal for RGB/Component/Video Signal
• PC Digital Input (DVI)
• Output terminal with VAO (variable audio output) support
9. Easy Setup
• Lens Shift, Power Zoom & Focus, Digital Keystone Correction
• High Speed Auto Sync Technology
10. Advanced Presentation Features incorporating a unique
gyro device for “in-air” remote control
• An intuitive presentation tool with an easy-to-see screen pointer.
• Raising the bar for roaming interaction with a wireless, RF (nondirectional)
design that erases out-of-sight worries. Loaded with USB mouse control.
11. Useful Features
• Picture-in-Picture, Digital Enlargement, Freeze
• Customizable Startup Screen & Background Screen
12. Application Software
• “Sharp Advanced Presentation Software—Professional Edition” (Network and
Remote Control)
LAN
LAN
LAN
E-6
Important
Information
Contents
Important Information
Operation Buttons
Setup & Connections
Introduction ..........................................
IMPORTANT SAFEGUARDS ................
Outstanding Features ..........................
Contents ................................................
How to Access the PDF Operation
Manuals ............................................
Part Names............................................
Accessories ..........................................
1
2
5
7
Basic Operation
Power Supply .........................................
Projecting Computer Images .................
Watching Video Images .........................
Watching Component Video Images .....
For Better Sound ....................................
Power ON/OFF .......................................
Setting Up the Screen ..........................
Multiple Function
Using the Adjustment Feet .....................
Using the Lens Shift ...............................
LENS Button ...........................................
Adjusting the Projection Distance ..........
Image Projection ..................................
Appendix
Maintenance &
Troubleshooting
Rear Projection .......................................
Projection Using a Mirror ........................
Ceiling-mount Projection ........................
E-7
Introducing GyroRemote .....................
GyroRemote Features ............................
Using GyroRemote .................................
Setting up GyroRemote ..........................
Using the Operation Buttons ..............
9
10
12
Setup &
Connections
Connections..........................................
Operation Buttons
13
13
14
17
18
18
19
20
20
20
21
22
29
29
29
29
30
30
32
36
39
39
39
39
40
40
Selecting the Input Signal Source ..........
Adjusting the Volume..............................
Muting the Sound ...................................
Superimposing a Black Screen ..............
Displaying a Still Image ..........................
Magnifying a Specific Portion
of an Image ....................................... 41
Adjusting the Picture Aspect Ratio ......... 42
Gamma Correction Function .................. 43
Maintenance &
Troubleshooting
Basic Operation
Lamp/Maintenance Indicators .............
Replacing the Lamp .............................
Replacing the Air Filter ........................
Troubleshooting ...................................
For SHARP Assistance (U.S.A. only) ..
67
68
70
71
71
49
52
53
53
54
Appendix
Connecting Pin Assignments .............
(RS-232C) Specifications and
Command Settings..........................
Wired Remote Control Terminal
Specifications ..................................
Computer Compatibility Chart ............
Dimensions ...........................................
Specifications .......................................
Glossary ................................................
Index ......................................................
72
73
76
77
78
79
80
81
Basic Operation
54
55
55
56
57
57
58
Operation Buttons
58
59
Multiple Function
59
60
61
Maintenance &
Troubleshooting
Basic Operations ....................................
Menu Bars ..............................................
Adjusting the Picture ..............................
Adjusting the Computer Images
(RGB menu only) ..............................
Adjusting the Sound ...............................
Displaying Dual Pictures
(RGB menu only) ..............................
Reducing Image Noise
(VIDEO menu only) ...........................
Turning On/Off the On-screen Display ...
Setting the Video Signal
(VIDEO menu only) ...........................
Selecting a Background Image ..............
Selecting a Startup Image ......................
Selecting the Economy Mode ................
Confirming the Lamp Usage Time .........
Reversing/Inverting Projected Images ...
Setting the Stacking Mode .....................
Locking the Operation Buttons
on the Projector .................................
Deselecting Inputs .................................
Selecting the Transmission Speed
(RS-232C) .........................................
Controling Multiple Projectors
with ID Numbers ...............................
Protecting Important Settings
with a Password ................................
Selecting the On-screen Display
Language ..........................................
Displaying the Adjustment Settings .......
44
44
45
47
Setup & Connections
Using the GUI (Graphical User
Interface) Menu Screen ...................
Important
Information
Contents
62
62
Multiple Function
Appendix
Using Extended Functionality
Features ...........................................
63
E-8
Important
Information
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to
install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet,
you can download it from the Internet (http://www.adobe.com) or install it from the CD-ROM.
To Install Acrobat Reader from the CD-ROM
For Windows:
1
2
3
4
5
6
Insert the CD-ROM in the CD-ROM drive.
Double click on the “My Computer” icon.
Double click on the “CD-ROM” drive.
Double click on the “acrobat” folder.
Double click on the “windows” folder.
Double click on the desired installation program
and follow the instructions on the screen.
For Macintosh:
1
2
3
4
5
Insert the CD-ROM in the CD-ROM drive.
Double click on the “CD-ROM” icon.
Double click on the “acrobat” folder.
Double click on the “mac” folder.
Double click on the desired installation program
and follow the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please download the
appropriate version from the Internet.
Accessing the PDF Manuals
For Windows:
1
2
3
4
5
6
Insert the CD-ROM in the CD-ROM drive.
Double click on the “My Computer” icon.
Double click on the “CD-ROM” drive.
Double click on the “manuals” folder.
Double click on the “xg-p20xu” folder.
Double click on the language (name of the folder)
that you want to view.
7 Double click on the “p20x” pdf file to access the
projector manuals.
Double click on the “saps” pdf file to access the
Sharp Advanced Presentation Software manual.
8 Double click on the pdf file.
For Macintosh:
1
2
3
4
5
Insert the CD-ROM in the CD-ROM drive.
Double click on the “CD-ROM” icon.
Double click on the “manuals” folder.
Double click on the “xg-p20xu” folder.
Double click on the language (name of the folder)
that you want to view.
6 Double click on the “p20x” pdf file to access the
projector manuals.
Double click on the “saps” pdf file to access the
Sharp Advanced Presentation Software manual.
7 Double click on the pdf file.
• If the desired pdf file cannot be opened by double clicking the mouse, start Acrobat Reader first, then specify the desired file
using the “File”, “Open” menu.
• See the “readme.txt” file on the CD-ROM for important information on the CD-ROM not included in this operation manual.
E-9
Important
Information
Part Names
Numbers next to the part names refer to the main pages in this manual where the topic is explained.
Projector
Front View
LAMP REPLACEMENT indicator
67
67
TEMPERATURE WARNING
indicator
POWER indicator
67
32
GYRO RF indicator
POWER buttons (ON/OFF)
19
39
VOLUME buttons (/)
MUTE button
39
44
MENU button
LENS button
21
51
AUTO SYNC button
INPUT 1, 2, 3, 4, 5 buttons
39
42
RESIZE button
LEARN button
37
43
GAMMA button
BLACK SCREEN button
40
44
UNDO button
ENTER button
44
44
ADJUSTMENT buttons
(∂/ƒ/ß/©)
Antenna
32
Lens shift dial
20
Speakers
52
Foot releases
20
Rear View
INPUT 3 port (DVI)
16
3
Cooling fan (Exhaust vent)
70
Air filter/Cooling fan
(Intake vent)
70
Cooling fan (Intake vent)
4
Kensington Security
Standard connector
4
Carrying handle
38
IR/Gyro switch
Computer AUDIO INPUT 2/3 terminal
(ø3.5 mm stereo minijack)
16
38
WIRED REMOTE control
input terminal
(ø3.5 mm stereo minijack)
INPUT 1 port (15-pin Mini D-sub)
14
18
AUDIO OUTPUT terminal
(ø3.5 mm stereo minijack)
Computer AUDIO INPUT 1 terminal
(ø3.5 mm stereo minijack)
14
56
OUTPUT port (15-pin Mini
D-sub) for INPUT 1, 2
INPUT 2 terminals (BNC)
15
35
USB port
RS-232C INPUT port/
RS-232C OUTPUT port
16
65
13
AC socket
S-VIDEO INPUT 5 terminal
(4-pin Mini DIN)
17
VIDEO INPUT 4 terminal (RCA)
17
17
AUDIO INPUT 4/5
terminals (RCA)
E-10
Important
Information
Part Names
Numbers next to the part names refer to the main pages in this manual where the topic is explained.
GyroRemote
Rear View
Front View
36
LED
Function
button (1)
33
33
Function
button (2)
INPUT button
39
32
POINTER button
LEFT-CLICK/
ENTER button
35
44
35
44
RIGHT-CLICK/
UNDO button
32
MENU button
39
VOLUME/
/ button
33
ASSIGN Select
button
36
RF CH button
37
TEACH button
POWER button
LENS button
Function
button (3)
Function
button (4)
32
21
33
32
GYRO ACTIVE
button
38
Wired remote
control input
33
BottomView
View
Bottom
Gyration U.S. Patents
5698784, 5825350, 5898421
Inserting and removing the batteries
Batteries are not pre-installed at the factory. When inserting batteries for the first time, follow steps 1, 3 and 4
below.
the two
in on the arrow
2 Remove
1 Press
upper batteries and
mark and slide in the
direction of the arrow
to remove the battery
cover.
Battery
cover
E-11
pull the tapes to pick
up two other
batteries at the
bottom of the
compartment.
Battery
compartment
3
Insert four AAA size
batteries, making
sure the polarities
match the and marks inside the
battery compartment
and the batteries are
placed on the tapes.
the side tabs
4 Insert
of the battery cover
into the slots and
press the cover in
until it is properly
seated.
Battery
cover
Important
Information
Accessories
Supplied Accessories
GyroRemote
RRMCG1631CESA
Four AAA size batteries
RGB cable
QCNW-5304CEZZ
ø2.5–ø3.5 mm wired remote
control cable
QCNW-5943CEZZ
USB mouse control cable
QCNW-5916CEZZ
Three BNC-RCA adaptors
QPLGJ0107GEZZ
CD-ROM
UDSKA0043CEN1
LCD projector operation manual
TINS-7354CEZZ
Lens cap
PCAPH1056CESA
Power cord
QACCU5013DE01
Computer audio cable
(ø3.5 mm stereo minijack cable)
QCNW-4870CEZZ
Extra air filter
PFILD0080CEZZ
Sharp Advanced Presentation
Software operation manual
TINS-7356CEZZ
ID number seal
TLABZ0781CEZZ
LCD projector quick guide
TINS-7355CEZZ
Optional cables
DVI cable (9 10, 3 m)
AN-C3DV
3RCA to 15pin D-sub cable (9 10, 3 m)
AN-C3CP
5BNC to 15pin D-sub cable (9 10, 3 m)
AN-C3BN
RS-232C serial control cable (32 10, 10 m)
AN-C10RS
E-12
Connections
Power Supply
Setup & Connections
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the rear of the projector.
Power cord
Make the necessary connections before proceeding. Connect the power cord to a wall outlet.
The POWER indicator lights up red and the projector enters standby mode.
POWER indicator
• If the bottom filter cover is not securely installed, the POWER indicator flashes.
E-13
Projecting Computer Images
Connecting the Projector to a Computer
You can connect your projector to a computer for projection of full color computer images.
Connecting to a computer using the standard 15-pin Input
1
1
2
3
4
4
Computer audio cable
RGB cable
Setup & Connections
3
2
Connect one end of the supplied RGB cable to the INPUT 1 port on the projector.
Connect the other end to the monitor output port on the computer. Secure the connectors by tightening the
thumb screws.
To use the built-in audio system, connect one end of the supplied computer audio cable to the AUDIO INPUT 1
terminal on the projector.
Connect the other end to the audio output terminal on the computer.
CAUTION
• Before connecting, be sure to turn both the projector and the computer off. After making all connections, turn the projector on first. The
computer should always be turned on last.
• Please read the computer’s operation manual carefully before making connections.
• Refer to page 77 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals
other than those listed may cause some of the functions not to work.
• A ø3.5 mm stereo minijack to stereo RCA audio cable adaptor may be necessary.
When connecting this projector to a computer, select “RGB” for “Signal Type” on the GUI menu. (See page 47 .)
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Authorized Sharp Industrial LCD
Products Dealer or Service Center.
• AUDIO INPUT 1 can be used to input audio corresponding to the INPUT 1.
E-14
Projecting Computer Images
• This projector uses a 5 BNC computer input to prevent deterioration of image quality.
• Connect the R (PR), G/G sync (Y), B (PB), HD/C sync and VD cables (sold separately) to the correct input
terminals on the projector and an RGB switcher (sold separately) connected to the computer, or connect a 5
BNC cable (sold separately) directly from the input terminals on the projector to the computer.
Setup & Connections
Connecting to an external RGB switcher or other compatible computers using the BNC Input
(Typically used in larger installations )
Computer audio cable
4
3
To audio output
terminal
To R (PR), G/G sync (Y), B (PB),
HD/C sync and VD output terminals
1
RGB cable
5 BNC cable
(sold separately)
2
1
2
3
4
RGB switcher
(sold separately)
To RGB switcher
Connect each BNC connector of a 5 BNC cable to the corresponding INPUT 2 terminals on the projector.
Connect the other end of the 5 BNC cable to the corresponding BNC terminals on the external RGB switcher.
Connect the RGB switcher to the computer using a RGB cable.
To use the built-in audio system, connect one end of the supplied computer audio cable to the AUDIO INPUT 2/
3 terminal on the projector.
Connect the other end to the audio output terminal on the computer or external audio system.
• A ø3.5 mm stereo minijack to stereo RCA audio cable adaptor may be necessary.
When connecting the projector to a compatible computer other than a PC (VGA/SVGA/XGA/SXGA/UXGA) or Macintosh (i.e.
Workstation), a separate cable may be needed. Please contact your dealer for more information.
When connecting this projector to a computer, select “RGB” for “Signal Type” on the GUI menu. (See page 47 .)
• Connecting computers other than the recommended types may result in damage to the projector, the computer, or both.
• AUDIO INPUT 2/3 can be used to input audio corresponding to the INPUT 2/3.
“Plug and Play” function (when connecting to a 15-pin terminal)
• This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible
computer will communicate their setting requirements, allowing for quick and easy setup.
• Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.
• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA DDC compatible computer.
E-15
Projecting Computer Images
Connecting to a computer using the RS-232C Port
When the RS-232C port on the projector is connected to a computer with an RS-232C cable (null modem, cross
type, sold separately), the computer can be used to control the projector and check the status of the projector.
See pages 73 , 74 and 75 for details.
Connect an RS-232C cable (null modem, cross type, sold separately) to the serial port on the computer.
Setup & Connections
RGB cable
Computer audio cable
RS-232C cable
(null modem, cross type, sold separately)
CAUTION
• Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer.
• The wireless mouse or RS-232C function may not operate if your computer port is not correctly set up. Please refer to the operation manual
of the computer for details on setting up/installing the correct mouse driver.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Authorized Sharp Industrial LCD
Products Dealer or Service Center.
Connecting to a computer using the direct digital input port
3
Computer audio cable
4
1
DVI cable (sold separately)
2
1
2
3
4
To audio output terminal
To digital output terminal
Connect one end of the DVI cable to the INPUT 3 port on the projector.
Connect the other end to the corresponding terminal on a computer.
To use the built-in audio system, connect one end of the supplied computer audio cable to the AUDIO INPUT 2/
3 terminal on the projector.
Connect the other end to the audio output terminal on the computer.
• This DVI port is DVI version 1.0 compatible. Therefore when the signal is input from copy guard system compatible (DVI version 2.0)
equipment, no signal will be received.
E-16
Watching Video Images
Connecting to a VCR, laser disc player and other audiovisual
equipment using the standard video Input
S-video cable (sold separately)
Example
Setup & Connections
To S-video output terminal
Video cable (sold separately)
1
VCR
To video output terminal
or
Laser disc player
2
Audio cable (sold separately)
To audio output terminals
1
2
Connect the yellow RCA connectors to the corresponding yellow VIDEO INPUT 4 terminal on the projector and
the Video output terminal on the video source.
To use the built-in audio system, connect the red and white RCA connectors to the corresponding red and white
AUDIO INPUT 4/5 terminals on the projector and the Audio output terminals on the video source.
The S-VIDEO INPUT 5 terminal uses a video signal system in which the picture is separated into a color and a luminance signal
to realize a higher-quality image.
• For higher quality video, you may use the S-VIDEO INPUT 5 terminal on the projector. S-video cable is sold separately.
• If your video equipment does not have an S-video output terminal, use a composite video cable.
CAUTION
• Always turn off the projector before connecting to video equipment, in order to protect both the projector and the equipment
being connected.
E-17
Watching Component Video Images
Connecting to a DVD video player, DTV decoder and other component
video equipment using the 5 BNC Input
4
To audio output terminals
Example
3
Setup & Connections
Audio cable
(ø3.5 mm stereo minijack/RCA cable,
sold separately)
DTV decoder
or
1
Component cable (sold separately)
2
To analog component output terminals
Three BNC-RCA adaptors
1
2
3
4
DVD video player
CAUTION
• Always turn off the projector before connecting to video
equipment, in order to protect both the projector and the
equipment being connected.
Connect each BNC connector of a component cable to the corresponding BNC INPUT 2 terminals on the
projector.
Connect the other end of the cable to the corresponding terminals on a DVD video player or DTV decoder.
To use the built-in audio system, connect one end of an audio cable (sold separately) to the AUDIO INPUT 2/3
terminal on the projector.
Connect the other end to the audio output terminal on the DVD video player or DTV decoder.
• BNC-RCA adaptors are included for use with RCA type cables and sources.
• A ø3.5 mm stereo minijack to stereo RCA audio cable adaptor may be necessary.
When connecting this projector to a DVD video player or DTV decoder, select “Component” for “Signal Type” on the GUI
menu. (See page 47 .)
For Better Sound
Connecting to an amplifier and other audio components
Audio cable (sold separately)
To audio input terminals
Amplifier
CAUTION
• Always turn off the projector before connecting to audio
components, in order to protect both the projector and the
components being connected.
• By using external audio components, the volume can be amplified for better sound.
• The AUDIO OUTPUT terminal allow you to output audio to audio components from the selected AUDIO INPUT 1 to 5 terminals connected to
audiovisual equipment.
• For details on Variable Audio Output (VAO) and Fixed Audio Output (FAO), see page 52 .
• A ø3.5 mm stereo minijack to stereo RCA audio cable adaptor may be necessary.
E-18
Power ON/OFF
Press POWER ON on the projector or
POWER on the GyroRemote.
Setup & Connections
POWER
• The flashing green LAMP REPLACEMENT indicator
shows that the lamp is warming up. Wait until the
indicator stops flashing before operating the projector.
• If the power is turned off and then immediately turned
on again, it may take a short while before the lamp
turns on.
• When the projector cannot recognize GyroRemote, an onscreen display appears. Follow the instructions to activate
control.
• After the projector is unpacked and turned on for the first
time, a slight odor may be emitted from the exhaust vent.
This odor will soon disappear with use.
LAMP REPLACEMENT
indicator
On-screen Display
When the power is on, the LAMP REPLACEMENT
indicator lights, indicating the status of the lamp.
Green: Lamp is ready.
Flashing green: Warming up.
Red: Change the lamp.
Press POWER OFF on the projector or
POWER on the GyroRemote.
Press POWER OFF/POWER again while the message
is displayed.
• If you accidentally pressed POWER OFF/POWER and do
not want to turn off the power, wait until the power off screen
disappears.
• When the power is turned off, the POWER indicator will light
up red and the cooling fan will run for about 90 seconds.
The projector will then enter standby mode.
• Wait until the cooling fan stops before disconnecting the
power cord.
• The power can be turned on again by pressing POWER
ON/POWER. When the power is turned on, the POWER
indicator and the LAMP REPLACEMENT indicator light
green.
• The POWER indicator flashes if the bottom filter cover is
not securely installed.
E-19
Setting Up the Screen
Using the Adjustment Feet
1
3
2
Setup & Connections
UP
Press foot releases.
Adjust height of projector
and remove hands from
foot releases.
DOWN
Rotate feet to make minor changes.
• The projector is adjustable up to approximately 10° from the standard position.
• When the height of the projector is adjusted, the image may become distorted (keystoned), depending on the relative
positions of the projector and the screen.
CAUTION
• Do not press the foot releases when the adjustment feet are extended without firmly holding the projector.
• Do not hold the lens when lifting or lowering the projector.
• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment feet and the
projector.
Using the Lens Shift
The picture can be adjusted within the shift range of the lens by rotating the dial on the top of the projector.
Projector
Projected Image
UP
Lens shift dial
UP
DOWN
DOWN
• The lens shift dial is set to the upper most position at the factory. Remember to adjust lower by turning the dial when operating the projector.
• The lens shift dial has two points to help orient the position. The center of the lens and bottom of the screen are the same height (10:0) and
the center of the lens and center of the screen are the same height (5:5). When either position is reached by turning the dial, you will notice
a slight latching feeling.
• Do not forcefully turn the lens shift dial beyond the 10:0 and 5:5 orientating positions; doing so may result in damaging the equipment.
• When the AN-P9MX of optional lens is attached, lens shift cannot be used.
E-20
LENS Button
Projector
GyroRemote
Digital Image Adjustments
This function can be used to adjust the focus, zoom,
keystone, v-size and digital shift settings.
Setup & Connections
ENTER
1
Press LENS to select mode. Each time LENS is
pressed, the screen changes as shown on the left.
2
Press ENTER to display test
pattern.
3
Press ∂/ƒ/ß/© to make
adjustments. (Press / to
make adjustments on the
GyroRemote.)
4
a. Press LENS until normal screen appears.
b. To reset the “KEYSTONE”, “V-SIZE” and
“DIGITAL SHIFT” setting, press UNDO.
LENS
∂/ƒ/ß/©
UNDO
On-screen Display
(Example: 4:3
NORMAL image)
On-screen Display
(Example: 16:9
WIDE image)
• Do not touch the lens when adjusting the focus or zoom.
Keystone setting
Trapezoidal distortion is caused when the projector
image is positioned away from the center axis of the
screen. This function allows you to correct the keystone
effect for excellent picture quality.
• Straight lines and the edges of the displayed image may appear
jagged, when adjusting the KEYSTONE setting.
V-size setting
During keystone correction an error can occur in the
aspect ratio depending on the amount of lens shift. Use
the V-SIZE fine-tuning function to correct this error.
• V-SIZE is only displayed and can only be adjusted when performing
KEYSTONE correction.
Digital shift setting
For easier viewing, this function shifts the image
projected on the screen up or down eliminating either
the upper or lower black band found in 16:9 and other
wide aspect ratios.
• Digital shift function only works with BORDER, STRETCH or SMART
STRETCH of VIDEO and DTV inputs. (See page 42 for details.)
The DIGITAL SHIFT screen is not displayed when projecting images
other than WIDE.
Digital Shift
or
Press ∂.
E-21
Press ƒ.
Adjusting the Projection Distance
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Move the projector forward or backward if the edges of the image are distorted.
Setup & Connections
• The projector lens should be centered in the middle of the screen. If the lens center is not perpendicular to the screen, the image will be
distorted, making viewing difficult.
• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out colors, making viewing
difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
Four optional lenses from Sharp are also available for specialized application. Please see your local Sharp Industrial
LCD Products Dealer to details on all the lenses. (Refer to the lens operation manual when attaching a lens.)
You can install the AN-W6EZ and AN-T6EZ optional lenses yourself. However, be sure to have service personnel
install the AN-P9MX and AN-P48EZ optional lenses.
Throw Distance
The graph below is for 100 inches (254 cm) screen with 4:3 normal mode.
Screen
AN-P9MX
511 (1.8 m)
Throw distance ratio 1:0.9
AN-W6EZ
86–112 (2.6–3.4 m)
Throw distance ratio 1:1.3–1.7
Standard
12–1511 (3.7–4.9 m)
Throw distance ratio 1:1.8–2.4
AN-T6EZ
165–216 (5.0–6.6 m)
Throw distance ratio 1:2.5–3.3
AN-P48EZ
3010–404 (9.4–12.3 m)
Throw distance ratio 1:4.6–6.1
5
10
15
20
25
30
35
40 (ft)
Standard Setup (Front Projection)
X
Place the projector at the required distance from the screen according to the
desired picture size. (See pages 24 to 28 .)
H
L
• Four optional lenses from Sharp are available for specialized application. Please see
your local Sharp Industrial LCD Products Dealer for details on all the lenses.
NORMAL Mode (4:3)
WIDE Mode (16:9)
16
3
4
: Screen size and Picture size (4:3)
9
3
4
: Screen size and Picture size (16:9)
: Signal mask area
E-22
Adjusting the Projection Distance
Upper and Lower Lens Shift Position
• This projector is equipped with a lens shift function that lets you adjust the projection height.
• Adjust to match the setup configuration.
Setup & Connections
Screen size: 100 inches (254 cm)
WIDE Mode: 16:9
Standard Lens as an example
Screen
Lens center
Upper lens
shift position
H: 2 1
(62.3 cm)
Upper lens shift position
(High mount setup)
Lens center
Lower edge of screen (White portion) = Standard (0) point
–H
Lower lens shift position H: 8.2
(20.8 cm)
Lower lens shift position
(Desktop setup)
Upper and Lower Lens Shift Position (Ceiling Mount)
When the projector is in the inverted position, use the upper edge of the screen as the base line, and exchange
the lower and upper lens shift values.
Screen
–H
Upper edge of screen
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level. Tilting or angling
the projector will reduce the effectiveness of the lens shift function.
E-23
Adjusting the Projection Distance
Standard Lens
Throw distance ratio
1:1.8 to 2.4
Screen size (4:3) (X)
Diag.
Width
Height
Projection distance (L)
Maximum (l1)
Minimum (l2)
Setup & Connections
NORMAL Mode (4:3)
Lens center to the lower edge of the screen (H)
Upper lens shift position (h1)
Lower lens shift position (h2)
300
240
180
47 0 (14.3 m)
36 2 (11.0 m)
7 6 (228.6 cm)
0.0 (0.0 cm)
200
160
120
32 2 (9.8 m)
24 3 (7.4 m)
5 0 (152.4 cm)
0.0 (0.0 cm)
150
120
90
23 6 (7.2 m)
18 4 (5.6 m)
3 9 (114.3 cm)
0.0 (0.0 cm)
100
80
60
15 11 (4.9 m)
12 0 (3.7 m)
2 6 (76.2 cm)
0.0 (0.0 cm)
84
67
50
13 2 (4.0 m)
10 1 (3.1 m)
2 1 (64.0 cm)
0.0 (0.0 cm)
72
58
43
11 1 (3.4 m)
8 6 (2.6 m)
1 10 (54.9 cm)
0.0 (0.0 cm)
60
48
36
9 6 (2.9 m)
7 3 (2.2 m)
1 6 (45.7 cm)
0.0 (0.0 cm)
40
32
24
6 1 (1.9 m)
4 7 (1.4 m)
1 0 (30.5 cm)
0.0 (0.0 cm)
The formula for screen size and projection distance
l1 (Max.) = (0.0482x 0.0226) 3.28
l2 (Min.) = (0.037x 0.041) 3.28
h1 (Upper) = 0.3x
h2 (Lower) = 0
WIDE Mode (16:9)
Screen size (4:3) (X)
Diag.
Width
Height
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
Projection distance (L)
Maximum (l1)
Minimum (l2)
Lens center to the lower edge of the screen (H)
Upper lens shift position (h1)
Lower lens shift position (h2)
300
261
147
51 3 (15.6 m)
39 5 (12.0 m)
6 2 (186.8 cm)
2 1 (62.3 cm)
200
174
98
34 5 (10.5 m)
26 5 (8.1 m)
4 1 (124.5 cm)
1 4 (41.5 cm)
150
131
74
25 11 (7.9 m)
19 11 (6.1 m)
3 1 (93.4 cm)
1 0 (31.1 cm)
133
116
65
23 0 (7.0 m)
17 7 (5.4 m)
2 9 (82.8 cm)
10.9 (27.6 cm)
106
92
52
18 3 (5.6 m)
14 0 (4.3 m)
2 2 (66.0 cm)
8.7 (22.0 cm)
100
87
49
17 0 (5.2 m)
13 1 (4.0 m)
2 1 (62.3 cm)
8.2 (20.8 cm)
92
80
45
15 10 (4.8 m)
12 1 (3.7 m)
1 11 (57.3 cm)
7.5 (19.1 cm)
84
73
41
14 1 (4.3 m)
10 10 (3.3 m)
1 9 (52.3 cm)
6.9 (17.4 cm)
72
63
35
12 0 (3.7 m)
9 3 (2.8 m)
1 6 (44.8 cm)
5.9 (14.9 cm)
60
52
29
10 2 (3.1 m)
7 10 (2.4 m)
1 3 (37.4 cm)
4.9 (12.5 cm)
40
35
20
6 6 (2.0 m)
5 0 (1.5 m)
9.8 (24.9 cm)
3.3 (8.3 cm)
The formula for screen size and projection distance
l1 (Max.) = (0.0525x 0.0546) 3.28
l2 (Min.) = (0.0404x 0.0397) 3.28
h1 (Upper) = 0.2451x
h2 (Lower) =0.0817x
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
• There is an error of 3% in the formula above.
• Values with a minus () sign indicate the distance of the lens center below the bottom of the screen.
E-24
Adjusting the Projection Distance
Setup & Connections
AN-W6EZ
Throw distance ratio
1:1.3 to 1.7
NORMAL Mode (4:3)
Screen size (4:3) (X)
Diag.
Width
Height
Projection distance (L)
Maximum (l1)
Minimum (l2)
Lens center to the lower edge of the screen (H)
Upper lens shift position (h1)
Lower lens shift position (h2)
300
240
180
33 11 (10.3 m)
26 1 (7.9 m)
7 6 (228.6 cm)
0.0 (0.0 cm)
200
160
120
22 6 (6.9 m)
17 3 (5.3 m)
5 0 (152.4 cm)
0.0 (0.0 cm)
150
120
90
16 10 (5.1 m)
12 11 (3.9 m)
3 9 (114.3 cm)
0.0 (0.0 cm)
100
80
60
11 2 (3.4 m)
8 6 (2.6 m)
2 6 (76.2 cm)
0.0 (0.0 cm)
84
67
50
9 4 (2.8 m)
7 1 (2.2 m)
2 1 (64.0 cm)
0.0 (0.0 cm)
72
58
43
8 0 (2.4 m)
6 1 (1.9 m)
1 10 (54.9 cm)
0.0 (0.0 cm)
60
48
36
6 7 (2.0 m)
5 0 (1.5 m)
1 6 (45.7 cm)
0.0 (0.0 cm)
40
32
24
4 4 (1.3 m)
3 3 (1.0 m)
1 0 (30.5 cm)
0.0 (0.0 cm)
The formula for screen size and projection distance
l1 (Max.) = (0.0347x 0.0709) 3.28
l2 (Min.) = (0.0267x 0.0715) 3.28
h1 (Upper) = 0.3x
h2 (Lower) = 0
WIDE Mode (16:9)
Screen size (4:3) (X)
Diag.
Width
Height
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
Projection distance (L)
Maximum (l1)
Minimum (l2)
Lens center to the lower edge of the screen (H)
Upper lens shift position (h1)
Lower lens shift position (h2)
300
261
147
37 0 (11.3 m)
28 5 (8.7 m)
6 2 (186.8 cm)
2 1 (62.3 cm)
200
174
98
24 7 (7.5 m)
18 10 (5.8 m)
4 1 (124.5 cm)
1 4 (41.5 cm)
150
131
74
18 4 (5.6 m)
14 1 (4.3 m)
3 1 (93.4 cm)
1 0 (31.1 cm)
133
116
65
16 3 (5.0 m)
12 6 (3.8 m)
2 9 (82.8 cm)
10.9 (27.6 cm)
106
92
52
12 11 (3.9 m)
9 11 (3.0 m)
2 2 (66.0 cm)
8.7 (22.0 cm)
100
87
49
12 2 (3.7 m)
9 4 (2.8 m)
2 1 (62.3 cm)
8.2 (20.8 cm)
92
80
45
11 2 (3.4 m)
8 6 (2.6 m)
1 11 (57.3 cm)
7.5 (19.1 cm)
84
73
41
10 2 (3.1 m)
7 9 (2.4 m)
1 9 (52.3 cm)
6.9 (17.4 cm)
72
63
35
8 8 (2.7 m)
6 8 (2.0 m)
1 6 (44.8 cm)
5.9 (14.9 cm)
60
52
29
7 3 (2.2 m)
5 6 (1.7 m)
1 3 (37.4 cm)
4.9 (12.5 cm)
40
35
20
4 9 (1.4 m)
3 7 (1.1 m)
9.8 (24.9 cm)
3.3 (8.3 cm)
The formula for screen size and projection distance
l1 (Max.) = (0.0378x 0.0726) 3.28
l2 (Min.) = (0.0291x 0.0731) 3.28
h1 (Upper) = 0.2451x
h2 (Lower) =0.0817x
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
• There is an error of 3% in the formula above.
• Values with a minus () sign indicate the distance of the lens center below the bottom of the screen.
E-25
Adjusting the Projection Distance
AN-T6EZ
Throw distance ratio
1:2.5 to 3.3
Screen size (4:3) (X)
Diag.
Width
Height
Projection distance (L)
Maximum (l1)
Minimum (l2)
Setup & Connections
NORMAL Mode (4:3)
Lens center to the lower edge of the screen (H)
Upper lens shift position (h1)
Lower lens shift position (h2)
300
240
180
65 9 (20.0 m)
50 5 (15.4 m)
7 6 (228.6 cm)
0.0 (0.0 cm)
200
160
120
43 8 (13.3 m)
33 5 (10.2 m)
5 0 (152.4 cm)
0.0 (0.0 cm)
150
120
90
32 7 (9.9 m)
24 11 (7.6 m)
3 9 (114.3 cm)
0.0 (0.0 cm)
100
80
60
21 6 (6.6 m)
16 5 (5.0 m)
2 6 (76.2 cm)
0.0 (0.0 cm)
84
67
50
18 0 (5.5 m)
13 8 (4.2 m)
2 1 (64.0 cm)
0.0 (0.0 cm)
72
58
43
15 4 (4.7 m)
11 8 (3.6 m)
1 10 (54.9 cm)
0.0 (0.0 cm)
60
48
36
12 8 (3.9 m)
9 7 (2.9 m)
1 6 (45.7 cm)
0.0 (0.0 cm)
40
32
24
8 3 (2.5 m)
6 2 (1.9 m)
1 0 (30.5 cm)
0.0 (0.0 cm)
The formula for screen size and projection distance
l1 (Max.) = (0.0674x 0.178) 3.28
l2 (Min.) = (0.0519x 0.1829) 3.28
h1 (Upper) = 0.3x
h2 (Lower) = 0
WIDE Mode (16:9)
Screen size (4:3) (X)
Diag.
Width
Height
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
Projection distance (L)
Maximum (l1)
Minimum (l2)
Lens center to the lower edge of the screen (H)
Upper lens shift position (h1)
Lower lens shift position (h2)
300
261
147
71 8 (21.8 m)
55 0 (16.8 m)
6 2 (186.8 cm)
2 1 (62.3 cm)
200
174
98
47 7 (14.5 m)
36 5 (11.1 m)
4 1 (124.5 cm)
1 4 (41.5 cm)
150
131
74
35 6 (10.8 m)
27 2 (8.3 m)
3 1 (93.4 cm)
1 0 (31.1 cm)
133
116
65
31 5 (9.6 m)
24 1 (7.3 m)
2 9 (82.8 cm)
10.9 (27.6 cm)
106
92
52
24 11 (7.6 m)
19 1 (5.8 m)
2 2 (66.0 cm)
8.7 (22.0 cm)
100
87
49
23 6 (7.2 m)
17 11 (5.5 m)
2 1 (62.3 cm)
8.2 (20.8 cm)
92
80
45
21 7 (6.6 m)
16 6 (5.0 m)
1 11 (57.3 cm)
7.5 (19.1 cm)
84
73
41
19 8 (6.0 m)
15 0 (4.6 m)
1 9 (52.3 cm)
6.9 (17.4 cm)
72
63
35
16 9 (5.1 m)
12 9 (3.9 m)
1 6 (44.8 cm)
5.9 (14.9 cm)
60
52
29
13 11 (4.2 m)
10 6 (3.2 m)
1 3 (37.4 cm)
4.9 (12.5 cm)
40
35
20
9 1 (2.8 m)
6 10 (2.1 m)
9.8 (24.9 cm)
3.3 (8.3 cm)
The formula for screen size and projection distance
l1 (Max.) = (0.0734x 0.1764) 3.28
l2 (Min.) = (0.0565x 0.1778) 3.28
h1 (Upper) = 0.2451x
h2 (Lower) =0.0817x
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
• There is an error of 3% in the formula above.
• Values with a minus () sign indicate the distance of the lens center below the bottom of the screen.
E-26
Adjusting the Projection Distance
Setup & Connections
AN-P9MX
Throw distance ratio
1:0.9
NORMAL Mode (4:3)
Screen size (4:3) (X)
Diag.
Width
Height
Projection distance (L)
Lens center to the lower edge of the screen (H)
300
240
180
18 1 (5.5 m)
7 6 (228.6 cm)
200
160
120
12 0 (3.7 m)
5 0 (152.4 cm)
150
120
90
9 0 (2.7 m)
3 9 (114.3 cm)
100
80
60
5 11 (1.8 m)
2 6 (76.2 cm)
84
67
50
4 11 (1.5 m)
2 1 (64.0 cm)
72
58
43
4 2 (1.3 m)
1 10 (54.9 cm)
60
48
36
3 6 (1.1 m)
1 6 (45.7 cm)
40
32
24
2 3 (0.7 m)
1 0 (30.5 cm)
The formula for screen size and projection distance
l = (0.0186x 0.0563) 3.28
h = 0.3x
WIDE Mode (16:9)
Screen size (4:3) (X)
Diag.
Width
Height
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
Lens center to the lower edge of the screen (H)
Projection distance (L)
300
261
147
19 9 (6.0 m)
6 2 (186.8 cm)
200
174
98
13 2 (4.0 m)
4 1 (124.5 cm)
150
131
74
9 10 (3.0 m)
3 1 (93.4 cm)
133
116
65
8 8 (2.6 m)
2 9 (82.8 cm)
106
92
52
6 10 (2.1 m)
2 2 (66.0 cm)
100
87
49
6 6 (2.0 m)
2 1 (62.3 cm)
92
80
45
5 11 (1.8 m)
1 11 (57.3 cm)
84
73
41
5 4 (1.6 m)
1 9 (52.3 cm)
72
63
35
4 8 (1.4 m)
1 6 (44.8 cm)
60
52
29
3 9 (1.2 m)
1 3 (37.4 cm)
40
35
20
2 6 (0.8 m)
10.0 (24.9 cm)
The formula for screen size and projection distance
l = (0.0203x 0.0579) 3.28
h = 0.2451x
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
• There is an error of 3% in the formula above.
• Values with a minus () sign indicate the distance of the lens center below the bottom of the screen.
E-27
Adjusting the Projection Distance
AN-P48EZ
Throw distance ratio
1:4.6 to 6.1
Screen size (4:3) (X)
Height
Width
Diag.
Projection distance (L)
Minimum (l2)
Maximum (l1)
Setup & Connections
NORMAL Mode (4:3)
Lens center to the lower edge of the screen (H)
Lower lens shift position (h2)
Upper lens shift position (h1)
300
240
180
119 9 (36.5 m)
91 6 (27.9 m)
7 6 (228.6 cm)
0.0 (0.0 cm)
200
160
120
80 1 (24.4 m)
61 4 (18.7 m)
5 0 (152.4 cm)
0.0 (0.0 cm)
150
120
90
60 0 (18.3 m)
45 11 (14.0 m)
3 9 (114.3 cm)
0.0 (0.0 cm)
100
80
60
40 4 (12.3 m)
30 10 (9.4 m)
2 6 (76.2 cm)
0.0 (0.0 cm)
84
67
50
33 10 (10.3 m)
25 11 (7.9 m)
2 1 (64.0 cm)
0.0 (0.0 cm)
72
58
43
29 2 (8.9 m)
22 4 (6.8 m)
1 10 (54.9 cm)
0.0 (0.0 cm)
60
48
36
24 3 (7.4 m)
18 8 (5.7 m)
1 6 (45.7 cm)
0.0 (0.0 cm)
The formula for screen size and projection distance
l1 (Max.) = (0.1214x 0.1272) 3.28
l2 (Min.) = (0.0927x 0.1233) 3.28
h1 (Upper) = 0.3x
h2 (Lower) = 0
WIDE Mode (16:9)
Screen size (4:3) (X)
Diag.
Width
Height
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
Projection distance (L)
Maximum (l1)
Minimum (l2)
Lens center to the lower edge of the screen (H)
Lower lens shift position (h2)
Upper lens shift position (h1)
300
261
147
130 7 (39.8 m)
99 9 (30.4 m)
6 2 (186.8 cm)
2 1 (62.3 cm)
200
174
98
87 3 (26.6 m)
66 7 (20.3 m)
4 1 (124.5 cm)
1 4 (41.5 cm)
150
131
74
65 7 (20.0 m)
50 2 (15.3 m)
3 1 (93.4 cm)
1 0 (31.1 cm)
133
116
65
58 1 (17.7 m)
44 7 (13.6 m)
2 9 (82.8 cm)
10.9 (27.6 cm)
106
92
52
46 3 (14.1 m)
35 5 (10.8 m)
2 2 (66.0 cm)
8.7 (22.0 cm)
100
87
49
44 0 (13.4 m)
33 6 (10.2 m)
2 1 (62.3 cm)
8.2 (20.8 cm)
92
80
45
40 4 (12.3 m)
30 10 (9.4 m)
1 11 (57.3 cm)
7.5 (19.1 cm)
84
73
41
36 9 (11.2 m)
28 3 (8.6 m)
1 9 (52.3 cm)
6.9 (17.4 cm)
72
63
35
31 10 (9.7 m)
24 3 (7.4 m)
1 6 (44.8 cm)
5.9 (14.9 cm)
60
52
29
26 7 (8.1 m)
20 4 (6.2 m)
1 3 (37.4 cm)
4.9 (12.5 cm)
The formula for screen size and projection distance
l1 (Max.) = (0.1323x 0.1272) 3.28
l2 (Min.) = (0.101x 0.1233) 3.28
h1 (Upper) = 0.2451x
h2 (Lower) =0.0817x
x: Screen size (diag.) (X) (inches)
l: Projection distance (L) (feet)
h: Lens center to the lower edge of the screen (H) (inches)
• There is an error of 3% in the formula above.
• Values with a minus () sign indicate the distance of the lens center below the bottom of the screen.
E-28
Image Projection
Rear Projection
Setup & Connections
• Place a translucent screen between the projector and
the audience.
• Use the projector’s menu system to reverse the
projected image. (See page 57 for use of this
function.)
• Optimal image quality can be achieved when the projector
is positioned perpendicular to the screen with all feet flat
and level.
Projection Using a Mirror
• When the distance between the projector and screen
is not sufficient for normal rear projection, you can
use a mirror to reflect the image onto the screen.
• Place a mirror (normal flat type) in front of the lens.
• Project the normal image onto the mirror.
• The image reflected from the mirror is projected onto
the translucent screen.
CAUTION
• When using a mirror, be sure to carefully position both the
projector and the mirror so the light does not shine into the
eyes of the audience.
Ceiling-mount Projection
• It is recommended that you use the optional Sharp
ceiling-mount bracket for this installation.
• Before mounting the projector, contact your nearest
Authorized Sharp Industrial LCD Products Dealer or
Service Center to obtain the recommended ceilingmount bracket (sold separately). (AN-XGCM61
ceiling-mount bracket, AN-EP101AP extension tube
for AN-XGCM61.)
• When the projector is in the inverted position, use the
upper edge of the screen as the base line.
• Use the projector’s menu system to select the
appropriate projection mode. (See page 57 for use
of this function.)
E-29
Introducing GyroRemote
GyroRemote Features
1. RF design provides nondirectional control.
2. Individual Recognition (Teach/Learn) function for multi-projector control.
3. Senses your natural hand motion for accurate control of mouse operations and
projector menus.
1. RF Technology
Nondirectional radio design with 98 5 (30 m) range.
Operation Buttons
• The control range measured is with the antenna fully extended.
• The control range under actual operating conditions may be less than optimum depending on where the projector is placed and the
radio signal environment.
RF: Nondirectional
98 5 (30 m)
98 5 (30 m)
98 5 (30 m)
98 5 (30 m)
2. Multi-Projector Control
An individual recognition function makes it possible to control multiple projectors.
No radio interference even if other projectors of the same type are within GyroRemote’s
operating range.
Projector: 1 unit
GyroRemote: 1 unit
Can operate multiple projections with one GyroRemote.
Projector: multiple units
GyroRemote: 1 unit
Can operate one projector using multiple GyroRemotes.
Projector: 1 unit
GyroRemote: multiple units
E-30
GyroRemote Features
3. Gesture tracking
Accurately tracks your hand movements in the air for pinpoint control of projector menus and computer cursor.
USB mouse control cable
Operation Buttons
Projector Control
(for OSD)
Mouse Control
• GYRO ACTIVE, LEFT-CLICK/ENTER and RIGHT-CLICK/UNDO controls depend on whether the
GyroRemote is operating the projector or the computer.
Projector Control
On-screen Display
Bright and easy-to-see screen pointer.
(See page 32 .)
Operate the menu with a simple wave of the hand.
(See page 32 .)
Inside the
upper cover
Press ASSIGN Select to toggle and display the 5
“Button ASSIGN” lists one-by-one. Each “Button
ASSIGN” list has 4 selection items.
(See page 33 .)
Mouse Control
You can operate your computer with the same operating
feeling as a normal mouse.
(See page 35 .)
E-31
Using GyroRemote
Preparation
Antenna
1 Switch on the projector power source. The projector
image will appear on the screen.
2 Pull out the projector antenna.
• The control range will not be optimized if you do not pull
out the antenna. Always use with the antenna fully
extended.
• The control range under actual operating conditions may
be less than optimum depending on where the projector
is placed and the radio signal environment.
3 Press POWER on the GyroRemote, located on the
Operation Buttons
front, inside the upper cover.
• The GYRO RF indicator on the projector flashes green
whenever it receives a radio signal from the GyroRemote.
Operating the screen pointer
1 Press POINTER on the GyroRemote.
As the POINTER is being pushed, a pointer on the
screen will display. If you release your finger from
the POINTER it will disappear from the screen.
2 Hold the GyroRemote and move it around freely in
the air. The pointer on the screen moves precisely
in concert with the movement of your GyroRemote
in hand.
Menu Adjustments
1 Open
the upper cover on the front of the
GyroRemote.
2 Press MENU.
3 Press
GYRO ACTIVE on the back of the
GyroRemote, and select your desired category by
moving the unit left or right.
4 Then select the desired item by moving the unit up
or down.
5 Move the unit left or right, or press / to adjust
item values.
6 Press MENU.
The menu display disappears.
• Double click on GYRO ACTIVE, the LED will light and you can
operate GyroRemote just like pressing the button continuously. To
cancel this mode, press GYRO ACTIVE once.
• If you release GYRO ACTIVE located on the back of the unit, you
will not be able to control operations no matter how you wave your
hand in the air.
E-32
Using GyroRemote
Button Assign list
On-screen Display
Function ASSIGN
1 Open the upper cover on the front of GyroRemote.
2 Press ASSIGN Select.
“Button Assign” list appears on the lower right of the
display. Each time you press ASSIGN Select,
“Button Assign” list changes as shown below.
1/5
GyroRemote
2/5
3/5
4/5
5/5
Function (1)
• Press ASSIGN Select. After the “Button Assign” list pops up press
LEFT-CLICK/ENTER to view a list of all selections. Refer to the list
of all Button Assign selections below.
Operation Buttons
Function (2)
RIGHT-CLICK/UNDO
LEFT-CLICK/ENTER
3 Press Function (1–4) and select the desired item.
4 Press
UNDO. The “Button Assign” list display
disappears.
• The Button Assign function is not recorded on the GyroRemote
itself, it is recorded on the projector side.
Inside the upper cover
Function (3)
Function (4)
ASSIGN Select
All Button Assign selections
: ASSIGN Select button
E-33
: LEFT-CLICK/ENTER button
: RIGHT-CLICK/UNDO button
Using GyroRemote
Using the Presentation Tools
This projector is equipped with presentation tools that can be used to emphasize keypoints within your presentation.
You can use these tools by accessing the “Button Assign” list on your GyroRemote. Choose popup list “1/5”. (See
page 33 .)
Button Assign list
Using stamps
1 Press Function (1) repeatedly to select the desired stamp.
• Types of stamps are changed as shown left.
2 Press and hold down GYRO ACTIVE to move the stamp
3
4
Stamp
Operation Buttons
Each time you press Function (1), stamps can be changed as
shown below.
to the desired position.
Release GYRO ACTIVE to set the stamp in the desired
position.
Press ENTER to bring up another stamp, then repeat steps
1 to 3 above.
Using lines
1 Press Function (2) repeatedly to select the desired line.
• Types of lines are changed as shown left.
Line
Each time you press Function (2), lines can be changed as
shown below (straight line, horizontal or vertical line, box, circle,
free line).
2 Press and hold down GYRO ACTIVE to move the line to
the desired starting position.
3 Release GYRO ACTIVE and press ENTER to set the line
4
5
Item Color
Each time you press Function (3), colors can be changed as
shown below.
Red
Green
Blue
Yellow
Black
White
Purple
Light blue
Clear SCRN
When you press Function (4), all items shown on the screen
can be cleared.
• The last item selected before switching off the power is saved as
the default setting.
• A check mark signifies “Stamp”, a straight line is for “Line” and red
is for “Item Color”.
6
in its starting position.
Press and hold down GYRO ACTIVE again and draw the
line by waving the unit around in the air freely.
Release GYRO ACTIVE to set the ending point and
complete the line drawing.
Press ENTER to bring up another line, then repeat steps
1 to 5 above.
• In steps 2 and 4 above, while holding down GYRO ACTIVE, wave
the unit around in the air with your hand. The stamps and starting
positions of the lines move and the lines are drawn precisely in
concert with your hand movements.
• To change colors, press Function (3) while performing any of the
steps above.
• To erase the item you just placed on the screen, press UNDO.
However, when you are drawing lines with the free line tool, pressing
UNDO will erase all free lines drawn.
Displaying the Break Timer
You can use this tool by accessing the “Button Assign” list on your GyroRemote. Choose popup list “2/5” and press
Function (4). (See page 33 .)
• As soon as Function (4) is pressed, the timer starts to count down from 5 minutes.
• If you press Function (4) again, the Break Timer is canceled.
• You can set the Break Timer from 1 to 60 minutes with ∂/ƒ on the
projector or / on the GyroRemote. The timer starts to count
down as soon as ∂/ƒ or / is pressed.
• The Break Timer is displayed against the background image
selected in “Selecting a Startup Image”. (See page 55 .)
E-34
Using GyroRemote
Operating the mouse
Basically operates the same as a standard mouse.
Connecting the projector to the computer
GyroRemote allows you to perform mouse operations on your computer.
1 Connect one end of a USB mouse control cable to your computer.
Operation Buttons
2 Connect the other end of the cable to the projector USB port.
USB mouse control cable
CAUTION
• Windows 95 does not support USB mouse driver software.
• The minimum system requirements for the USB type mouse system are shown below.
Windows
Hardware: PC/AT compatible machine with USB port
OS: Windows 98/Windows 2000/Windows Me
Macintosh
Hardware: Macintosh series with USB port
OS: Mac OS 8.5 or higher
• If this is the first time connecting the projector to the PC, the PC may need to load standard USB drivers from the operating system. Follow
the on-screen instructions. Some operating systems (Windows 98) may prompt you to insert the original operating system installation CDROM, if the USB driver is not already loaded on the PC.
Using the mouse
You can operate GyroRemote when there is no onscreen display.
1 Press GYRO ACTIVE on the back of GyroRemote.
While pressing, wave the unit around in the air with
your hand. The mouse cursor responds precisely in
concert with your hand movements.
GyroRemote
2 Release
your finger from GYRO ACTIVE. The
mouse cursor will stop moving around.
LEFT-CLICK/
ENTER
RIGHT-CLICK/
UNDO
GYRO ACTIVE
E-35
• For left/right mouse clicks, we recommend that you first move
the cursor to the item you want to click on, then release your
finger from GYRO ACTIVE before clicking your target.
• When the projector is connected to a computer by a USB mouse
cable, you can still operate the mouse even if the projector is
unplugged. (However, only when GyroRemote is not connected
to the projector by wired remote control cable.)
Setting up GyroRemote
The projector uses RF channel and TEACH/LEARN settings to recognize individual projectors that may be operating
in the same area, and keep them from interfering with each other. One GyroRemote can operate multiple projectors
or you can even use multiple GyroRemotes to control one projector.
Setting RF channels
GyroRemote uses radio signals, which can receive interference under certain conditions. To avoid interference,
you can switch RF channels. GyroRemote has 8 channels.
GyroRemote
Confirming the present RF channel
1 Press RF CHlocated on the front, inside the upper
cover.
Operation Buttons
LED
2 The current channel in use is displayed on the lower
right of the screen. You can also confirm the RF
channel by the number of times the LED flashes.
(Ex: RF Channel 7 if the LED flashes 7 times.)
Switching RF channels
1 Press RF CH for over 1 sec.
2 Each time you press for over 1 sec. the RF channel
RF CH
changes as shown below.
1
2
3
4
5
6
7
8
3 Each time you change RF channels it is displayed
in the lower right of the screen.
On-screen Display
• An auto-search is performed on the projector side, so there is no
need for manually adjusting the projector
E-36
Setting up GyroRemote
TEACH/LEARN
• Each GyroRemote has its own ID code, which must be recognized by the projector that is going to be used.
• The projector only recognizes the signal of the GyroRemote whose ID code has been input. Signals from other
projectors or GyroRemotes that may be operating in the same area are not allowed to interrupt each other.
Projector
GyroRemote
ENTER
1 Press LEARN on the projector.
2 While “Do you want to LEARN?” is displaying, press
ENTER. You are now in LEARN mode.
CAUTION
• Entering LEARN mode erases all previously registered
GyroRemotes data. You must re-enter each GyroRemote ID code
in order for the projector to recognize them again.
Operation Buttons
3 Press TEACH located on the front, inside the upper
TEACH
LEARN
cover on the remote within 5 minutes. “Register” will
appear on the display and you can now start using
the GyroRemote with the projector.
4 To exit from the LEARN mode, press LEARN.
• LEARN mode will exit if the LEARN is pressed or 5 minutes has
elapsed.
Operating multiple projectors with one
GyroRemote
On-screen Display
CAUTION
• Be aware that you can operate multiple projectors with one
GyroRemote, even if you are in another room, as long as you stay
within a 98 5 (30 m) range of the projector.
1 Set projector to LEARN mode.
2 Press TEACH on the GyroRemote. You
can now
operate multiple projectors with one GyroRemote.
3 Perform steps 1 and 2 for each projector you plan to
use.
4 To exit from LEARN mode, press LEARN.
• For setting multiple units in LEARN mode at one time, perform step
1 above for all projectors.
Using multiple GyroRemotes to operate one
projector
One projector can recognize up to 8 GyroRemote ID
codes.
1 Set projector to LEARN mode.
2 Press TEACH on all GyroRemotes being used. Once
the eighth GyroRemote is registered to operate one
projector, the LEARN mode automatically finishes.
You can now operate one projector using multiple
GyroRemotes.
3 To exit from the LEARN mode, press LEARN.
• Contact your nearest Authorized Sharp Industrial LCD Products
Dealer or Service Center if you need to use an additional
GyroRemote unit.
E-37
Setting up GyroRemote
Turning off GyroRemote
CAUTION
• Make sure to turn off GyroRemote aboard aircraft or other places where using radio signals is prohibited.
GyroRemote
LED
Press TEACH and RF CH located inside the upper
cover at the same time, the LED will flash 3 times
and the GyroRemote will turn off.
2
If the LED doesn’t light up after pressing any of the
buttons (except POWER), the GyroRemote power
is turned off.
• Press TEACH and RF CH at the same time or POWER located
inside the upper cover of the GyroRemote to turn the power on.
• When the power is turned off, the GyroRemote is protected from
malfunctioning or battery depletion if control buttons are
inadvertently pressed.
Operation Buttons
POWER
1
TEACH
RF CH+
Using as a Wired Remote Control
When the GyroRemote cannot be used due to the range or positioning of the projector (rear projection, etc.),
connect a ø3.5 mm stereo minijack cable (sold separately) from the wired remote control input on the bottom of
the remote control to the WIRED REMOTE control input terminal on the rear of the projector.
ø3.5 mm stereo minijack cable
(sold separately)
ø2.5–ø3.5 mm wired
remote control cable
(supplied)
IR/Gyro switch
Using the GyroRemote with a wired remote control cable
Slide the IR/Gyro switch to the Gyro position.
• To prevent unwanted transmission of radio signals, GyroRemote turns itself off if detached from the ø2.5–ø3.5 mm wired remote control
cable.
• When the cable is inserted into the projector, the projector will not receive radio signals.
Using the IR remote control as a wired remote
You can use the IR remote control by connecting a ø3.5 mm stereo minijack cable (sold separately) from the wired
remote control input on the bottom of the remote control to the WIRED REMOTE control input terminal, a SHARP
product.
Slide the IR/Gyro switch to the IR position.
• Depending on the IR remote type connected, you may not be able to use certain functions.
E-38
Using the Operation Buttons
Selecting the Input Signal Source
Projector
GyroRemote
Press INPUT again to change the mode.
You can use these tools by accessing the “Button Assign”
list on your GyroRemote. Choose popup list “5/5”. (See
page 33 .)
INPUT
• When no signal is received, “NO SIGNAL” will be displayed.
When a signal that the projector is not preset to receive is
received, “NOT REG.” will be displayed.
Operation Buttons
On-screen Display
INPUT 1 Mode
INPUT 2 Mode
INPUT 4 Mode
INPUT 5 Mode
INPUT 3 Mode
Adjusting the Volume
Projector
GyroRemote
Press VOLUME / to adjust the volume.
On-screen Display
VOLUME
Muting the Sound
Projector
Press MUTE to temporarily turn off the sound.
Press MUTE again to turn the sound back on.
MUTE
You can use this tool by accessing the “Button Assign”
list on your GyroRemote. Choose popup list “2/5” and
press Function (3). (See page 33 .)
On-screen Display
E-39
Superimposing a Black Screen
This function can be used to superimpose a black
screen over the projected image.
Projector
Blacking out the Projected Image
Press BLACK SCREEN. The screen turns black and
“BLACK SCREEN” is displayed on the screen. To return
to the original projected image, press BLACK SCREEN
again.
BLACK SCREEN
You can use this tool by accessing the “Button Assign”
list on your GyroRemote. Choose popup list “2/5” and
press Function (1). (See page 33 .)
Operation Buttons
Projected Image
sg
Displaying a Still Image
GyroRemote
Function (2)
This function allows you to instantly freeze a moving
image. This is useful when you want to display a still
image from a computer or video, giving you more time
to explain the image to the audience.
You can also use this function to display a still image
from a computer while you make preparations for the
next computer images to be presented.
You can only use this tool by accessing the “Button
Assign” list on your GyroRemote. Choose popup list “2/
5” and press Function (2). (See page 33 .)
ASSIGN Select
1 Press Function (2) to freeze the image.
Button Assign list
2 Press Function (2) again to return to the moving
image.
On-screen Display
E-40
Magnifying a Specific Portion of an Image
This function allows you to magnify a specific portion of
an image. This is useful when you want to display a
detailed portion of the image.
GyroRemote
Function (1)
Function (2)
You can only use these tools by accessing the “Button
Assign” list on your GyroRemote. Choose popup list “3/
5” and press Function (1) or (2). (See page 33 .)
UNDO
1 Press Function (2) to zoom in. (Press Function (1)
GYRO ACTIVE
to zoom out.)
1
4
9
16
36
64
ASSIGN Select
2 To return to 1, press UNDO.
Operation Buttons
Function (3)
• If you press Function (1) when the zoom is set to 1, no
change will occur. And if you press Function (2) when the
zoom is set to 64, no change will occur.
• If the input signal is changed during digital image
magnification, the image will return to 1. The input signal
is changed
(a) when INPUT is pressed,
(b) when the input signal is interrupted, or
(c) when the input resolution and refresh rate changes.
Button Assign list
On-screen Display
4
Press Function (2)
to zoom in.
Pan Around the Screen
Enlarging the screen image and move it around.
You can use this tool by accessing the “Button Assign”
list on your GyroRemote. Choose popup list “3/5” and
press Function (3). (See page 33 .)
Press Function (3).
1 When the image is magnified, press and hold down
GYRO ACTIVE, and then move the unit in the
direction of the image which you want to see.
2 To exit from the Screen Pan mode, press Function
(3).
• The Screen Pan icon remains on the screen for a few
seconds after the enlargement setting icon disappears. (The
same as when the menu is displayed.)
• Select “Screen Pan” when you want to remove the Screen
Pan icon (exiting this mode).
• You can also pan and scan around the image by using ∂/
ƒ/ß/© on the projector.
E-41
Adjusting the Picture Aspect Ratio
This function allows you to modify or customize the picture display mode
to enhance the input image. Depending on the input signal, you can
choose NORMAL, FULL, DOT BY DOT, BORDER, STRETCH or SMART
STRETCH image.
Projector
RESIZE
1
Press RESIZE. Each time RESIZE is pressed, the picture mode
changes as shown below.
2
To return to the standard image, press UNDO while “RESIZE” is
displayed on the screen.
You can use this tool by accessing the “Button Assign” list on your
GyroRemote. Choose popup list “4/5” and press Function (3). (See page
33 .)
UNDO
COMPUTER
EXAMPLE
NORMAL
Output screen image
FULL
RESIZE
RESIZE
NORMAL
FULL
DOT BY DOT
SVGA (800 600)
1024 768
–
800 600
XGA (1024 768)
1024 768
–
–
SXGA (1280 960)
1024 768
–
1024 768
UXGA (1600 1200) 1024 768
–
1024 768
DOT BY DOT
DOT BY DOT
For 4:3
aspect ratio
NORMAL
FOR 4:3 aspect ratio
For without
4:3 aspect ratio
RESIZE
NORMAL
SXGA (1280 1024)
Operation Buttons
Input Signal
960 768 1024 768 1024 768
FOR 4:3 aspect ratio
(1024 768)
RESIZE
RESIZE
NORMAL
RESIZE
FULL
DOT BY DOT
FOR 5:4 aspect ratio
(1280 1024)
VIDEO/DTV
Input Signal
Output screen image
BORDER
STRETCH
NORMAL
RESIZE
RESIZE
RESIZE
STRETCH
BORDER
SMART STRETCH
RESIZE
SMART STRETCH
NORMAL
480i
480P
NTSC
PAL
SECAM
FOR 4:3 aspect ratio
RESIZE
RESIZE
RESIZE
STRETCH
BORDER
RESIZE
SMART STRETCH
NORMAL
with squeeze
720P
1080i
RESIZE
STRETCH
FOR 16:9 aspect ratio
EXAMPLE
SMART
NORMAL BORDER STRETCH STRETCH
For 4:3
aspect ratio
For 16:9
aspect ratio
NTSC, SECAM, 480i 1024 768
768 576 1024 576* 1024 576*
PAL, 580i
1024 768
768 576 1024 576* 1024 576*
480P
1024 768
768 576 1024 576* 1024 576*
720P
–
–
1024 576*
–
1080i
–
–
1024 576*
–
* The digital image shift function can be used with these picture display modes.
E-42
Gamma Correction Function
Projector
GAMMA
Operation Buttons
UNDO
On-screen Display
(Example: RGB mode)
s
STANDARD
• Gamma is an image quality enhancement function
that offers a richer image by brightening the darker
portions of the image without altering the brightness
of the brighter portions.
• Four gamma settings are available to allow for
differences in the images displayed and in the
brightness of the room.
• When you are displaying images with frequent, dark
scenes, such as a film or concert, or when you are
displaying images in a bright room, this feature makes
the dark scenes easier to see and gives the
impression of greater depth in the image.
Gamma Modes
Selected Mode
Gamma mode
STANDARD
Standard picture without gamma correction.
PRESENTATION Brightens darker portions of image for more
enhanced presentations.
CINEMA
Gives greater depth to darker portions of image
for a more exciting theater experience.
CUSTOM
Allows you to adjust gamma value using Sharp
Advanced Presentation Software.
1
Press GAMMA. Each time GAMMA is pressed,
the gamma level toggles as shown on the left.
2
To return to the standard image, press UNDO while
“GAMMA” is displayed on the screen.
s
PRESENTATION
You can use this tool by accessing the “Button Assign”
list on your GyroRemote. Choose popup list “4/5” and
press Function (1). (See page 33 ).
s
CINEMA
CUSTOM
E-43
• The CUSTOM setting of VIDEO mode optimizes the video
source to reproduce the image more beautifully. It darkens
bright portions of the image and gives greater depth to
darker portions of the image.
Select CUSTOM as your default setting if you prefer a
smooth textured image to a sharply contrasted one.
• STANDARD and CINEMA settings of VIDEO mode (except
COMPONENT 480P/720P/1080i) incorporate a DYNAMIC
GAMMA function for optimizing GAMMA correction frame
by frame in real time, thus providing a more beautiful image.
• PRESENTATION settings are the same for both RGB and
VIDEO modes.
Using the GUI (Graphical User Interface) Menu Screen
Basic Operations
This projector has two sets of menu screens that allow you to adjust the image and various projector
settings. These menu screens which appear on pages 47 to 62 can be operated from the projector or
the GyroRemote with the following procedure.
Projector
For operating the GyroRemote, see page 32 .
MENU
∂/ƒ/ß/©
UNDO
ENTER
(GUI) On-screen Display
INPUT 1, 2 (RGB) or 3 (DIGITAL) mode
1
Press MENU to display the INPUT 1, 2, 3, 4 or 5
mode menu bar.
2
Press ß/© to select an adjustment menu on the
menu bar.
3
Press ∂/ƒ to select a specific adjustment item.
4
To display a single adjustment item, press ENTER
after selecting the item. Only the menu bar and
the selected adjustment item will appear.
5
Press ß/© to adjust the item.
6
Press UNDO to return to the previous screen.
7
To exit from the GUI, press MENU.
2
3
5
4
2
5
INPUT 4, 5 (VIDEO) mode
1
Basic Operation
1
• For details on items on the menu screen, see the tree charts on
pages 45 and 46 .
2
3
5
E-44
Menu Bars
Items on the INPUT 1, 2 or 3 Mode Menu Bar
Main menu
Picture
30
Bright
30
30
Color
30
30
CeilingFront
Tint
30
30
Rear
Sharp
30
30
Red
30
30
Blue
30
30
3
3
Options (2)
Master
Component
Slave
3D Progressive
Progressive Mode
Film Mode
150 150
H-Pos
60
150 150
V-Pos
60
60
1
2
Resolution
800600
640480
Keylock Level
Level B
Vert Freq
75 Hz
72 Hz
Set Inputs
•
7
1
2
Resolution
800600
640480
Vert Freq
75 Hz
72 Hz
RS-232C
•
Select Setting
1
2
Auto Sync
Auto Sync Disp [ON/OFF]
30
Treble
30
30
Bass
30
30
[ON/OFF]
Input 4
[ON/OFF]
Input 5
[ON/OFF]
9600bps
ID No.
Old Password
New Password
•
Reconfirm
640480
37.5 kHz
72 Hz
Language
English
Deutsch
Español
Off
Normal
High Speed
30
Input 3
Password
•
Resolution
Hor Freq
Vert Freq
Balance
[ON/OFF]
Set ID No.
7
Audio
[ON/OFF]
Input 2
115200bps
Resolution
Signal Info
Input 1
38400bps
•
7
Special Modes
Normal
Level A
•
Reset
Save Setting
Normal
RGB
2D Progressive
60
Front
CeilingRear
Stack Setting
Signal Type
Clock
Lamp Timer
PRJ Mode
Reset
Phase
Basic Operation
Sub menu
30
CLR Temp
Fine Sync
Main menu
Sub menu
Contrast
Nederlands
Français
Italiano
Svenska
Português
Reset
FAO
Audio Out
Options (1)
Speaker
[ON/OFF]
Pict in Pict
[ON/OFF]
OSD Display
VAO
Status
Normal
Level A
Level B
Background
Sharp
Custom
Blue
None
Startup Image
Sharp
Economy Mode
Custom
MNTR Out/RS232C[ON/OFF]
Auto Power Off [ON/OFF]
E-45
None
• The resolution, vertical frequency and horizontal
frequency figures displayed above are for example
purposes only.
• “Color”, “Tint”, and “Sharp” appear only when
Component input is selected in INPUT 1 or 2 mode. For
INPUT 3 (DVI), in “Picture” menu, only “CLR Temp” is
active and the other menus are displayed in gray. In “Fine
Sync” menu, only “Signal Info” is active and the other
menus are displayed in gray.
• Only the items highlighted in the tree charts above can
be adjusted.
• To adjust the items under the sub menu, press © after
selecting the sub menu.
Menu Bars
Items on the INPUT 4 or 5 Mode Menu Bar
Main menu
Picture
Main menu
Sub menu
Sub menu
Contrast
30
30
Bright
30
30
Color
30
30
CeilingFront
Tint
30
30
Rear
Sharp
30
30
Red
30
30
Blue
30
30
3
CLR Temp
Options (2)
Lamp Timer
PRJ Mode
CeilingRear
Stack Setting
Slave
Reset
Keylock Level
2D Progressive
Level B
Film Mode
Input 1
[ON/OFF]
Balance
30
30
Input 2
[ON/OFF]
Treble
30
30
Input 3
[ON/OFF]
Bass
30
30
Input 4
[ON/OFF]
Input 5
[ON/OFF]
Set Inputs
Reset
Audio Out
Options (1)
Normal
Level A
3D Progressive
Audio
Normal
Master
3
Progressive Mode
Front
FAO
Speaker
[ON/OFF]
DNR
[ON/OFF]
VAO
38400bps
115200bps
Normal
Set ID No.
ID No.
Level A
Password
Old Password
Level B
Video System
New Password
Auto
PAL (50/60Hz)
Background
9600bps
Basic Operation
OSD Display
RS-232C
Reconfirm
Language
English
SECAM
Deutsch
NTSC4.43
Español
NTSC3.58
Nederlands
PAL–M
Français
PAL–N
Italiano
Sharp
Svenska
Custom
Português
Blue
None
Startup Image
Sharp
Custom
Status
None
Economy Mode
MNTR Out/RS232C[ON/OFF]
Auto Power Off [ON/OFF]
• Only the items highlighted in the tree charts above can be adjusted.
• To adjust the items under the sub menu, press © after selecting the sub menu.
E-46
Adjusting the Picture
You can adjust the projector’s picture to your preferences with the following picture settings. See page
44 for the procedure details.
e. g. RGB input in INPUT 1 or 2 mode
Selected item
ß button
© button
Contrast
For less contrast
For more contrast
Bright
For less brightness
For more brightness
Color
For less color intensity
For more color intensity
Tint
Skin tones become purplish
Skin tones become greenish
Sharp
For less sharpness
For more sharpness
Red
For weaker red
For stronger red
Blue
For stronger blue
For weaker blue
All image adjustment items are returned to the factory preset
settings.
Reset
Basic Operation
•
•
•
•
“Color”, “Tint” and “Sharp” do not appear for RGB input in INPUT 1 or 2 mode.
To reset all adjustment items, select “Reset” on the “Picture” menu screen and press ENTER.
The adjustments can be stored separately in the INPUT 1 to 5 modes.
Depending on the type of signal received, “Sharp” may not be adjustable for COMPONENT input in INPUT 1 or 2 mode.
Adjusting the Color Temperature
This function can be used to adjust the color temperature to suit the type of image input to the projector
(video, computer image, TV broadcast, etc.). Decrease the color temperature to create warmer, reddish
images for natural flesh tones, or increase to create cooler, bluish images for a brighter picture.
3
(Red) ß button
Decreases color temperature for
warmer, reddish,
incandescent-like images.
(Low color temperature)
3
© button (Blue)
Increases color temperature for
cooler, bluish, florescent-like
images.
(High color temperature)
Selecting the Signal Type (RGB menu only)
This function allows you to select the input signal type RGB or COMPONENT for INPUT 1 or 2 port.
You can use this tool by accessing the “Button Assign” list on your GyroRemote. Choose popup list “4/5” and press
Function (4). (See page 33 .)
E-47
Adjusting the Picture
Progressive Mode
This function allows you to select the progressive display of a video signal. The progressive display
projects a smoother video image. See page 44 for the procedure details.
Selects the progressive conversion mode.
2D Progressive
This function is useful to display fast-moving images such
as sports and action films. Mode that optimizes the image
in a displayed frame.
3D Progressive
This function is useful to display relatively slow-moving
images such as drama and documentary more clearly.
Mode that optimizes the image by estimating the movement
of a number of preceding and succeeding frames.
Film Mode
Reproduces the image of film software clearly. Displays the
optimized image of film transformed with three-two pull down
enhancement to progressive mode images.
Basic Operation
• Film Mode cannot work with PAL 50 Hz.
E-48
Adjusting the Computer Images (RGB menu only)
When displaying computer patterns which are very detailed (tiling, vertical stripes, etc.), interference
may occur between the LCD pixels, causing flickering, vertical stripes, or contrast irregularities in portions
of the screen. Should this occur, adjust “Clock”, “Phase”, “H-Pos” and “V-Pos” for the optimum computer
image. See page 44 for the procedure details.
Select the desired computer input mode with INPUT 1 or 2.
Clock
Adjusts vertical noise.
Phase
Adjusts horizontal noise (similar to tracking on your VCR).
H-Pos
Centers the on-screen image by moving it to the left or
right.
V-Pos
Centers the on-screen image by moving it up or down.
Basic Operation
• Computer image adjustments can be made easily by pressing AUTO SYNC ( ). See page 51 for details.
• To reset all adjustment items, select “Reset” on the “Fine Sync” menu screen and press ENTER.
Saving and Selecting Adjustment Settings
This projector allows you to store up to seven adjustment settings for use with various computers. Once
these settings are stored, they can be easily selected each time you connect a computer to the projector.
Saving the adjustment setting
Selecting a saved setting
• If a memory position has not been set, a resolution and frequency setting will not be displayed.
• When selecting the stored adjustment setting with “Select Setting”, the computer system should match the stored setting.
E-49
Adjusting the Computer Images (RGB menu only)
Special Mode Adjustment
Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected.
However, for some signals, the optimal resolution mode in “Special Modes” on the “Fine Sync” menu
screen may need to be selected to match the computer display mode. See page 44 for the procedure
details.
Basic Operation
• Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the
image hard to see.)
• When inputting DTV 480P or 1080i signals, select the corresponding type of signal.
Checking the Input Signal
This function allows you to check the current input signal information.
E-50
Adjusting the Computer Images (RGB menu only)
Auto Sync Adjustment
• Used to automatically adjust a computer image.
• Auto Sync adjustment can be made manually by pressing AUTO SYNC, or automatically by setting
“Auto Sync” to “Normal” or “High Speed” in the projector’s GUI menu. See page 44 for the procedure
details.
You can use this tool by accessing the “Button Assign” list on your GyroRemote. Choose popup list “4/5” and press
Function (2). (See page 33 .)
Off
• Synchronized adjustment is not automatically performed.
• Press AUTO SYNC to perform manual adjustment.
Normal
• Synchronized adjustment is automatically performed the
same as the “High Speed” setting.
• Adjustment using the “Normal” setting takes longer to
perform than using the “High Speed” setting, but it is more
accurate.
High Speed
Basic Operation
• The sync adjustment is automatically made each time the
projector is turned on while connected to a computer or
the input selection is changed.
• The Auto Sync adjustment setting previously made is
cleared when the projector’s setting is changed.
• Automatic adjustments can be made by pressing AUTO SYNC.
• When performing AUTO SYNC in Off or High Speed mode, if you press AUTO SYNC once, then press it again within one
minute, AUTO SYNC will be executed in Normal mode.
• Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector.
• When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page 49 .)
Auto Sync Display Function
Normally, an image is not superimposed during Auto Sync adjustment. You can, however, choose to
superimpose a background image during Auto Sync adjustment.
E-51
Adjusting the Sound
This projector’s audio is factory preset to standard settings. However, you can adjust it to suit your own
preferences by adjusting the following audio settings. See page 44 for the procedure details.
Selected item ß button
© button
Balance
Increased audio from the left speaker
Increased audio from the right speaker
Treble
For weaker treble
For stronger treble
Bass
For weaker bass
For stronger bass
Reset
All audio adjustment items are returned to the factory preset settings.
• To reset all adjustment items, select “Reset” on the “Audio” menu screen and press
ENTER.
Audio Out
FAO (Fixed audio output): Audio output that does not vary in strength with
the volume level of the source projector.
VAO (Variable audio output): Audio output that varies in strength with the
volume level of the source projector.
Basic Operation
Speaker
Switching the built-in speakers on the projector ON/OFF.
E-52
Displaying Dual Pictures (RGB menu only)
Picture in Picture function allows you to display two pictures on the same screen. You can display the
image input from INPUT 4 or 5 as an inset picture overlapping the main picture input from INPUT 1, 2 or
3. See page 44 for the procedure details.
You can use this tool by accessing the “Button Assign” list on your GyroRemote. Choose popup list “3/5” and press
Function (4). (See page 33 )
300
250
200
A
150
B
100
C
50
0
1
2
1996
1997
1998
1999
Press ß to select “ ” to display an inset picture (Factory preset to INPUT 4).
Press ß/©/∂/ƒ to move the inset picture to one of four preset positions.
Basic Operation
• The image from INPUT 1, 2 or 3 is displayed as the main picture and the image from INPUT 4 or 5 is displayed as the inset picture.
• The last displayed image from INPUT 4 or 5 is displayed as the inset picture.
For example, when you want to display the image from INPUT 4 as the inset picture, select INPUT 4, then select the main picture, and
then select “Pict in Pict”.
• Inset picture can only be displayed in video signal of NTSC/PAL/SECAM.
• When selecting the image for the inset picture, only the images being input will be displayed.
• The audio of the inset picture will come out of the projector’s speakers.
• Picture in Picture does not work in case of the following RGB signals.
UXGA signal image/Interlaced signal/DTV (480P/720P/1080i)
• You can only use the following functions while in Picture in Picture mode.
FREEZE: Works for the inset picture only.
Reducing Image Noise (VIDEO menu only)
Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross color
noise. See page 44 for the procedure details.
• If the image is clear, select “
E-53
” to prevent any blurring.
Turning On/Off the On-screen Display
This function allows you to turn on or off the on-screen messages that appear during input select.
See page 44 for the procedure details.
Selected item
Description
Normal
Level A
All On-screen Display are displayed.
Input/Custom/Freeze/Enlarge/Auto sync/Volume/Mute/
Black screen functions are not displayed.
All On-screen Display are not displayed (except Menu/
Button assign list/Lens functions and warning display
(Power off/Temp./Lamp function etc.)).
Level B
Setting the Video Signal (VIDEO menu only)
Basic Operation
The video input system mode is preset to “Auto”; however, it can be changed to a specific system mode
if the selected system mode is not compatible with the connected audiovisual equipment. See page
44 for the procedure details.
• When the system mode is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur,
switch to the video system of the source signal.
• AUTO cannot be set for PAL-M and PAL-N input signals. Select “PAL-M” or “PAL-N” in “Video System” menu for PAL-M and
PAL-N input signals.
E-54
Selecting a Background Image
This function allows you to select the image displayed when no signal is being sent to the projector. See
page 44 for the procedure details.
Selected item
Description
Sharp
SHARP default image
Custom
User customized image (i.e. company logo)
Blue
Blue screen
None
Black screen
• By selecting “Custom”, the projector can display a custom image (i.e. your company logo) as the background image. The
custom image must be a 256-color BMP file with a picture size no larger than 1,024 768 pixels. Please see the Sharp
Advanced Presentation Software operation manual for how to save (or change) a custom image.
Basic Operation
Selecting a Startup Image
This function allows you to specify the image to be displayed upon the projector’s startup.
A custom image (i.e. your company logo) can be uploaded to the projector via an RS-232C cable. See
page 16 in this operation manual, and also the supplied Sharp Advanced Presentation Software
operation manual for detailed instructions. See page 44 for the procedure details.
Selected item
Description
Sharp
SHARP default image
Custom
User customized image (i.e. company logo)
None
Black screen
• By selecting “Custom”, the projector can display a custom image (i.e. your company logo) as the startup image. The custom
image must be a 256-color BMP file with a picture size no larger than 1,024 768 pixels. Please see the Sharp Advanced
Presentation Software operation manual for how to save (or change) a custom image.
E-55
Selecting the Economy Mode
These functions allow you to reduce the power consumption when the projector is in standby mode.
See page 44 for the procedure details.
Monitor Out/RS-232C Off Function
This projector consumes power when using a monitor connected to the OUTPUT port for INPUT 1, 2 and a
computer connected to the RS-232C port. When not using these ports, “MNTR Out/RS232C” can be set to “ ”
to reduce standby power consumption.
Standby power for Monitor Out/RS-232C
connection turned off.
Monitor Out/RS-232C on
CAUTION
• Set “MNTR Out/RS232C” to “
” when using the Sharp Advanced Presentation Software (supplied).
Basic Operation
Automatic Power Shutoff Function
When no input signal is detected for more than 15 minutes, the projector will automatically shut off. The on-screen
message, “Power OFF in 5 min.” will appear five minutes before the power is automatically turned off.
Power automatically shuts off after 15 minutes
of no signal input.
Automatic Power Shutoff disabled.
• “MNTR Out/RS232C” is factory preset to “
”, and “Auto Power Off” is factory preset to “
”.
E-56
Confirming the Lamp Usage Time
This function allows you to check the accumulated lamp usage time. See page 44 for the procedure
details.
• It is recommended that the lamp be replaced after approximately 1,000 cumulative hours of use. See pages 68 and 69 for
lamp replacement.
Basic Operation
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function which allows you to reverse or invert the
projected image for various applications. See page 44 for the procedure details.
Selected item
Description
Front
Normal image
CeilingFront
Inverted image
Rear
Reversed image
CeilingRear
Reversed and inverted image
• This function is used for the reversed image and ceiling-mount setups. See page 29 for these setups.
E-57
Setting the Stacking Mode
You can double the brightness of an image by stacking two projectors and projecting same picture
simultaneously. To control two projectors, assign one as the master and one as the slave. The slave
projector will duplicate any operational settings made to the master projector. See page 44 for the
procedure details.
• When the projector is set to “Master”, button operation signals will be transmitted through RS-232C.
• When the projector is set to “Slave”, operations follow the button operations sent from the “Master”.
• When set to slave, all buttons on the projector along with ENTER, UNDO, POWER, LENS and MENU on the GyroRemote
can be used. The slave cannot operate the other buttons on GyroRemote.
• For details on intended purpose, see pages 65 and 66 .
Basic Operation
Locking the Operation Buttons on the Projector
This function can be used to lock the use of certain operation buttons on the projector. The user can still
operate the projector fully with the GyroRemote. See page 44 for the procedure details.
Selected item
Description
Normal
All operation buttons are functional.
Level A
Only Input/Volume/Mute functions on the
projector are available.
Level B
All operation buttons on the projector are
unavailable.
• To cancel the Keylock Level, perform the above procedure using the GyroRemote.
• See page 61 for details using the password function.
E-58
Deselecting Inputs
This function allows you to deselect unwanted signal input. See page 44 for the procedure details.
• When stack projecting, multi-screen projecting and so on, this function can be used to cancel the RS-232C control.
• Up to two input signals can be blocked for both Input 1, 2, 3 or Input 4, 5.
• For details on intended purpose, see pages 65 and 66 .
Basic Operation
Selecting the Transmission Speed (RS-232C)
This menu allows you to adjust the transmission speed of the RS-232C connection by selecting the
baud rate. See page 44 for the procedure details.
• Make sure that both the projector and computer are set for the same baud rate. Refer to the computer’s operation manual
for instructions for setting the baud rate.
E-59
Controling Multiple Projectors with ID Numbers
This projector can form a network of up to 250 projectors. To identify separately and control specified
projector, you need to set ID No.. The ID No. is factory preset to “001”. See page 44 for the procedure
details.
Setting the ID No.
Press © to select the first digit and ∂/ƒ to select the desired number. Continue this procedure for the remaining
two digits.
Basic Operation
• Be sure to set the ID No. in the Option menu and attach a corresponding number seal to the projector.
• The ID No. can be set from 001 to 250.
• For details on intended purpose, see pages 63 to 66 .
E-60
Protecting Important Settings with a Password
A password can be set by the user and used with the keylock level to prevent adjustments to certain
settings on the GUI. See page 44 for the procedure details.
• When password is set, you need to enter the password to use “PRJ Mode”, “Stack Setting”, “Keylock Level”, “Set Inputs”,
“RS-232C” and “Set ID No.” menus.
Basic Operation
Setting the Password
1
Enter the new password using ∂/ƒ to select the desired number, and then press © to select the next digit.
Continue this procedure for the remaining three digits, and then press ENTER.
2
Enter the password again (“Reconfirm”) using ∂/ƒ/ß/©, and then press ENTER.
• After setting the password, be sure to write it down in a secure location in case you can not remember it.
Changing the Password
E-61
1
Enter the old password using ∂/ƒ/ß/©, and then press ENTER.
2
Enter the new password using ∂/ƒ/ß/©, and then press ENTER.
3
Enter the password again (“Reconfirm”) using ∂/ƒ/ß/©, and then press ENTER.
Selecting the On-screen Display Language
English is the preset language for the On-screen Display; however, this can be changed to German,
Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese. See page 44 for
the procedure details.
Displaying the Adjustment Settings
Basic Operation
This function can be used to display all the adjusted settings on the screen simultaneously. See page
44 for the procedure details.
INPUT 1, 2 (RGB) or 3 (DIGITAL) mode
INPUT 4, 5 (VIDEO) mode
E-62
Using Extended Functionality Features
This projector has outstanding network capability.
• Internet access for self-diagnosis
• Multiple and group projector control
• Simultaneous multiple projector control
Internet access for self-diagnosis, status information and preventive
maintenance
LAN
E-mail
E-mail
Multiple Function
Internet
LAN
LAN
This projector can be used in a network of up to 250 projectors managed from a single PC with the accompanied
Sharp Advanced Presentation Software—Professional Edition. This projector can be connected to a PC using an
RS-232C connection. Output terminals are provided (RS-232C on the projector) enabling a daisy chain configuration
and eliminating the need for a distributor.
This projector is also equipped with a function to send status information (lamp usage time, etc.) to a Sharp
Service Center or outside contractor for quick and efficient customer service.
• For more information on these features, see the operation manuals accompanying the Sharp Advanced Presentation Software—
Professional Edition and optional boards.
E-63
(RS-232C)
Using
Extended
Specifications
Functionality
and Command
Features Settings
Multiple and group projector control via computer
Building
RS-232C
3rd Floor
RS-232C
Control PC
Sharp Advanced
Presentation Software
“Professional Edition”
2nd Floor
RS-232C
1st Floor
Video
Source 1
Video
Source 2
Multiple Function
This projector can be used in a network of projectors managed from a single PC with the accompanied Sharp
Advanced Presentation Software—Professional Edition. Projectors in conference rooms on the first and third floors
of a building, for example, can be used for video presentations, while projectors on the second floor can be used
for PC-assisted presentations. Projectors can even be powered down at different times (e.g., projectors on the first
and second floors are powered down in one hour, while those on the third floor are powered down in two hours).
• For more information on these features, see the operation manuals accompanying the Sharp Advanced Presentation Software—
Professional Edition.
• Transmission performance of the RS-232C cable can vary depending on the surrounding conditions. Use the transmission
repeater if performance is not up to par.
• We recommend you use an RS-232C cable not longer than 49 3 (15 m).
E-64
Using Extended Functionality Features
Simultaneous multiple projector control for stacking and videowall
projection
Multiple Function
Stack Projection
Master
INPUT1
OUTPUT
Stack Setting
Master
Set Inputs
INPUT1 Yes
INPUT2 Yes
INPUT3 No
INPUT4 Yes
INPUT5 Yes
Stack Setting
Slave
Set Inputs
INPUT1 Yes
INPUT2 No
INPUT3 No
INPUT4 Yes
INPUT5 Yes
INPUT2
INPUT4
INPUT5
RS-232C IN
RS-232C OUT
Distributor
Slave
INPUT1
DVD
OUTPUT
INPUT2
Laser Disc
INPUT4
INPUT5
RS-232C IN
RS-232C OUT
For brighter images, two projectors can be stacked using the Stack Setting function, with one projector set as the
Master and the other as the Slave. The operations of the Slave projector are controlled by the Master projector
during projection through an RS-232C connection. The RS-232C cable (null modem, cross type, sold separately)
is connected from the RS-232C output on the Master projector to the RS-232C input on the Slave projector.
Projectors can be stacked using an RS-232C cable (null modem, cross type, sold separately).
• See page 58 , “Setting the Stacking Mode”, and page 59 , “Deselecting Inputs”.
E-65
Using Extended Functionality Features
Videowall
Sharp Advanced
Presentation Software
“Professional Edition”
Control PC
RGB
SOURCE1
001
RGB
SOURCE2
INPUT1
Master
003
Slave
OUTPUT
INPUT1
OUTPUT
INPUT2
INPUT4
INPUT5
INPUT4
RS-232C IN
RS-232C OUT
INPUT5
RS-232C IN
RS-232C OUT
Distributor
002
INPUT1
Slave
004
Slave
OUTPUT
INPUT1
OUTPUT
INPUT2
INPUT2
INPUT4
VIDEO
SOURCE
DVD
INPUT5
INPUT4
RS-232C IN
RS-232C OUT
INPUT5
RS-232C IN
RS-232C OUT
Slave
Set Inputs
INPUT1 Yes
INPUT2 No
INPUT3 No
INPUT4 Yes
INPUT5 No
This projector can be used together with other projectors managed using the accompanied Sharp Advanced
Presentation Software—Professional Edition to create a videowall projection. Whereas conventional videowall
technology required the use of an image distributor, this projector videowall feature enables easy image settings
from a PC when inputting a single video source. This function greatly simplifies videowall setup.
RS-232C OUTPUTS also realize the simple daisy chain connection. The master projector directly connected to the
computer can make the daisy chain connection with multiple slave projectors. For details on setting master or
slave, see page 58 .
• Use a videowall projector stand, sold separately, when using this function.
• Image quality may deteriorate when picture signals are input through multiple projectors in a daisy chain
connection.
• For more information on this feature, see the operation manuals accompanying the Sharp Advanced Presentation Software—
Professional Edition.
• When UXGA signal is displayed, the videowall can not be set by Sharp Advanced Presentation Software—Professional
Edition.
E-66
Multiple Function
INPUT2
Master
Set Inputs
INPUT1 Yes
INPUT2 Yes
INPUT3 No
INPUT4 Yes
INPUT5 Yes
Lamp/Maintenance Indicators
Maintenance Indicators
POWER
indicator
LAMP
REPLACEMENT
indicator
Maintenance Indicator
TEMPERATURE
WARNING indicator
TEMPERATURE
WARNING
indicator
Condition
The internal
temperature is
abnormally high.
• The warning lights on the projector indicate problems
inside the projector.
• There are two warning lights: a TEMPERATURE
WARNING indicator which warns that the projector is
too hot, and a LAMP REPLACEMENT indicator which
lets you know when to change the lamp.
• If a problem occurs, either the TEMPERATURE
WARNING indicator or the LAMP REPLACEMENT
indicator will light up red. After turning off the power,
follow the procedures given below.
Problem
Possible Solution
• Blocked air intake.
• Relocate the projector to an area with
proper ventilation.
• Clogged air filter.
• Replace the filter.
(See page 70 .)
• Cooling fan breakdown.
• Internal circuit failure.
• Take the projector to your nearest
Authorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
LAMP REPLACEMENT indicator
The lamp does not
light up.
• Burnt-out lamp.
• Lamp circuit failure.
• Carefully replace the lamp. (See pages 68
and 69 .)
• Take the projector to your nearest
Authorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
POWER indicator
The POWER
indicator flashes in
red when the
projector is on.
• The filter cover is open.
• Securely install the filter cover.
• If the TEMPERATURE WARNING indicator lights up, follow the above possible solutions and then wait until the projector has
cooled down completely before turning the power back on. (At least 5 minutes.)
• If the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicator may be
triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet and put it back
in again.
Lamp
Maintenance &
Troubleshooting
It is recommended that the lamp be replaced after approximately 1,000 cumulative hours of use or when you
notice a significant deterioration of the picture and color quality. The lamp usage time can be checked with the
On-screen Display. (As the usage environment can vary significantly, the projector lamp may not operate for 1,000
hours.)
CAUTION
• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.
E-67
Replacing the Lamp
CAUTION
• Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest
Authorized Sharp Industrial LCD Products Dealer or Service Center for a replacement.
• Do not remove the lamp cage directly after operation of the projector. The lamp may be extremely
hot. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp cage
to fully cool before removing the lamp cage.
It is recommended that the lamp be replaced after approximately 1,000 cumulative hours of use or when you
notice a significant deterioration of the picture and color quality. Carefully change the lamp by following the steps
below.
If the new lamp does not light after replacement, take your projector to the nearest Authorized Sharp Industrial
LCD Products Dealer or Service Center for repair. Purchase a replacement lamp unit (lamp/cage module) of the
current type BQC-XGP20X//1 from your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center.
Then carefully change the lamp by following the instructions below. If you wish, you may have the lamp replaced
at your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this
projector under warranty, including lamp replacement, must be obtained through an Authorized Sharp Industrial LCD
Products Dealer or Service Center. For the name of the nearest Authorized Sharp Industrial LCD Products Dealer or
Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
U.S.A. ONLY
Removing and installing the lamp unit
CAUTION
• Be sure to remove the lamp cage by the handle. Be sure not to touch the glass surface of the lamp cage or the inside of
the projector.
• To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.
• Be sure to change the air filter during lamp replacement. The air filter comes packaged with the lamp unit.
1
Turn off the power.
Press POWER OFF. Wait until
the cooling fan stops.
Push the antenna completely
down to its resting position.
2
Disconnect the power
cord.
Unplug the power cord from the
AC socket.
3
Remove the bottom
filter cover.
Turn over the projector. Press the
tab and lift open the filter cover
in the direction of the arrow.
Tab
Remove the air filter.
Grasp the air filter between your
fingers and lift it out of the filter
cover.
5
Replace the air filter.
Place the air filter underneath the
tabs on the filter frame.
6
Maintenance &
Troubleshooting
4
Replace the filter
cover.
Insert the tab on the end of the
filter cover into the filter cover
opening and press the filter
cover into position.
Tab
E-68
Replacing the Lamp
7
Remove the lamp cage
cover.
Turn over the projector and
loosen the user service screw
that secures the lamp cage
cover. Then slide the cover in
the direction of the arrow.
8
Remove the lamp
cage.
Remove the securing screws
from the lamp cage. Hold the
lamp cage by the handle and
pull it towards you.
Securing
screw
9
Insert the new lamp cage.
Press the lamp cage firmly into
the lamp cage compartment.
Fasten the securing screws.
Securing
screws
User service screw
the lamp cage
10 Attach
cover.
Slide the lamp cage cover in
the direction of the arrow. Then
tighten the user service screw.
User service screw
Resetting the lamp timer
1
Connect the power
cord.
Maintenance &
Troubleshooting
Plug the power cord into the AC
socket of the projector.
2
Reset the lamp timer.
While pressing ƒ, © and
ENTER on the projector, press
POWER ON on the projector.
• Reset the lamp timer only after replacing the lamp.
E-69
“LAMP 0000H” is displayed,
indicating that the lamp timer is
reset.
Replacing the Air Filter
• This projector is equipped with two air filters to ensure the optimal operating condition of the projector.
• The air filters should be cleaned every 100 hours of use. Clean the filters more often when the projector is used
in a dusty or smoky location.
• Have your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center exchange the filter
(PFILD0080CEZZ) when it is no longer possible to clean it.
Bottom View
Side and Rear View
Air filter (not removable)
Air filter
Cleaning and replacing the bottom air filter
off the power and
1 Turn
2
disconnect the power
cord.
Press POWER OFF. Wait until
the cooling fan stops.
Push the antenna completely
down to its resting position.
Remove the bottom
filter cover.
Turn over the projector. Press the
tab and lift open the filter cover
in the direction of the arrow.
3
Remove the air filter.
Grasp the air filter between your
fingers and lift it out of the filter
cover.
Tab
4
Clean the air filter.
Clean the dust off the air filter
and cover with a vacuum
cleaner extension hose.
5
Replace the air filter.
Place the air filter underneath
the tabs on the filter frame.
6
Replace the filter
cover.
Insert the tab on the end of the
filter cover into the filter cover
opening and press the filter
cover into position.
Maintenance &
Troubleshooting
Tab
• Be sure the filter cover is securely installed. The power will not turn on unless it is correctly installed.
Cleaning the side air filter (not removable)
If dust or dirt has collected inside the air filter, clean the filter with a vacuum cleaner extension hose.
• The side air filter cannot be removed.
E-70
Troubleshooting
Problem
Power cannot be turned on or
off using the POWER buttons
(ON/OFF) on the projector.
Check
• Keylock level is set to “Level A” or “Level B”, preventing operation of some or all
buttons. (See page 58 .)
Cannot be operated by
GyroRemote.
• Register GyroRemote once again the projector. (See page 37 .)
• When the GyroRemote is connected to the projector with wired remote control cable,
confirm the position of the IR/Gyro switch. (See page 38 .)
• When the projector is set to slave, use the buttons on the master projector or change the
setting by RS-232C commands from the computer. (See page 58 .)
Cannot be operated by all
buttons of the projector and
GyroRemote.
• When using slave setting in combination with Keylock Level B, all the buttons on the
projector and the GyroRemote are disabled. Use the SAPS or RS-232C commands to
release slave and Keylock setting and enable buttons to operate.
Without a computer, you can release slave and Keylock setting by entering the buttons
on the projector as follows.
ON → ENTER → ON → ENTER → ON → ENTER → MENU
However, this operation also releases the password set.
No picture and no sound.
•
•
•
•
•
Sound is heard but no picture
appears.
• Cables incorrectly connected to rear panel of the projector. (See pages 13 – 18 .)
• “Contrast” and “Bright” adjustments are set to minimum position. (See page 47 .)
• On-screen Display (“BLACK SCREEN”) is turned off and Black Screen function is turned
on, creating a black image. (See page 40 .)
Color is faded or poor.
• “Color” and “Tint” adjustments are not correct. (See page 47 .)
Picture is blurred.
• Adjust the focus. (See page 21 .)
• Projection distance is too long or too short to allow for proper focus. (See pages 22 – 28 .)
Picture appears but no sound
is heard.
• Cables incorrectly connected to rear panel of the projector. (See pages 13 – 18 .)
• Volume is set to minimum. (See page 39 .)
No OSD appears.
• OSD Display is set to “Level A” or “Level B”, preventing to display some or all On-screen
Displays. (See page 54 .)
Projector power cord is not plugged into the wall outlet.
The bottom filter cover is not securely installed.
Selected input is wrong. (See page 39 .)
Cables incorrectly connected to rear panel of the projector. (See pages 13 – 18 .)
GyroRemote batteries have run down. (See page 11 .)
Maintenance &
Troubleshooting
An unusual sound is occasion- • If the picture is normal, the sound is due to cabinet shrinkage caused by temperature
ally heard from the cabinet.
changes. This will not affect operation or performance.
Maintenance indicator lights
up.
• Refer to “Lamp/Maintenance Indicators” on page 67 .
Picture noise appears.
• Adjust the “Phase” setting. (See page 49 .)
• Noise may appear when used with certain computers. Set the NOISE FILTER to ON
using the RS-232C command. (See pages 73 – 75 .)
480P images do not appear.
• Set the resolution mode to 480P. (See page 50 .)
Image is green on INPUT 1 or
2 COMPONENT.
Image is pink (no green) on
INPUT 1, 2 RGB.
• Change the input signal type. (See page 47 .)
Lens comes off.
• Align the mark on the lens with the corresponding mark on the projector, push the lens
firmly in place, and rotate to the right.
For SHARP Assistance (U.S.A. only)
If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting”
section on this page. If this operation manual does not answer your question, please call toll free 1-888-GOSHARP (1-888-467-4277) for further assistance. Or, send us an e-mail at lcdsupport@sharplcd.com .
Our World Wide Web address is http://www.sharplcd.com .
E-71
Connecting Pin Assignments
INPUT 1 RGB and OUTPUT (INPUT 1, 2) Signal Ports: 15-pin Mini D-sub female connector
5
10
15
1
6
11
RGB Input
Analog
1. Video input (red)
2. Video input
(green/sync on green)
3. Video input (blue)
4. Reserve input 1
5. Composite sync
6. Earth (red)
7. Earth (green/sync on green)
Component Input
Analog
1. PR (CR)
2. Y
3. PB (CB)
4. Not connected
5. Not connected
6. Earth (PR)
7. Earth (Y)
8. Earth (PB)
8.
9.
10.
11.
12.
13.
14.
15.
Earth (blue)
Not connected
GND
GND
Bi-directional data
Horizontal sync signal
Vertical sync signal
Data clock
9.
10.
11.
12.
13.
14.
15.
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable
1
6
Pin No.
1
2
3
4
5
6
7
8
9
5
9
Signal
CD
RD
SD
ER
SG
DR
RS
CS
CI
Name
I/O
Receive Data
Send Data
Input
Output
Signal Ground
Data Set Ready
Request to Send
Clear to Send
Output
Output
Input
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
INPUT 3 DVI Port: 29-pin
C1C2
9
1
8 16
17
24 C3 C4
C5
Name
T.M.D.S. Data 2
T.M.D.S. Data 2
T.M.D.S. Data 2/4 Shield
T.M.D.S. Data 4*3
T.M.D.S. Data 4*3
DDC Clock
DDC Data
Analog Vertical Sync
T.M.D.S. Data 1
T.M.D.S. Data 1
T.M.D.S. Data 1/3 Shield
T.M.D.S. Data 3*3
T.M.D.S. Data 3*3
5 V Power
Ground*1
Hot Plug Detect
T.M.D.S. Data 0
T.M.D.S. Data 0
T.M.D.S. Data 0/5 Shield
T.M.D.S. Data 5*3
T.M.D.S. Data 5*3
T.M.D.S. Clock Shield
T.M.D.S. Clock
T.M.D.S. Clock
Analog Red
Analog Green
Analog Blue
Analog Horizontal sync
Analog Ground*2
Appendix
• *1 Return for 5 V, Hsync. and Vsync.
• *2 Analog R, G and B return
• *3 These pins are not used on this equipment.
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
E-72
(RS-232C) Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type, sold
separately) to the projector. (See page 16 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the
projector processes the command from the computer, it sends a response code to the computer.
Command format
C1
C2
C3 C4
P1
P2
Command 4-digit
Response code format
Normal response
O
P3
Return code (0DH)
P4
Parameter 4-digit
Return code (0DH)
K
Problem response (communication error or incorrect command)
E
R
Return code (0DH)
R
When more than one code is being sent, send each command only after the OK response code for the previous
command from the projector is verified.
• When using the computer control function of the projector, the projector operating status cannot be read to the computer.
Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with
the On-screen Display. If the projector receives a command other than a menu display command, it will execute the command without displaying the On-screen Display.
Commands
EXAMPLE
• When “BRIGHT” of INPUT 1 (RGB 1) image adjustment is set to 10.
Computer
A
B
R
Appendix
BUTTONS & REMOTE CONTROL KEY
CONTROL CONTENTS
E-73
_
1
0
COMMAND PARAMETER
Projector
O
K
RETURN
POWER ON
P O W R _ _ _ 1 OK OR ERR
POWER OFF
P O W R _ _ _ 0 OK OR ERR
VOLUME (0 – 60)
V O L A _ _ * * OK OR ERR
MUTE ON
M U T E _ _ _ 1 OK OR ERR
MUTE OFF
M U T E _ _ _ 0 OK OR ERR
LENS FOCUS (30 – 30)
L N F O _ * * * OK OR ERR
LENS ZOOM (30 – 30)
L N Z O _ * * * OK OR ERR
KEYSTONE (127 – 127)
K E Y S * * * * OK OR ERR
V-SIZE (30 – 30)
V S I Z _ _ * * OK OR ERR
DIGITAL SHIFT (96 – 96)
L N D S _ * * * OK OR ERR
CONTROL CONTENTS
BUTTONS & REMOTE CONTROL KEY
R
→
←
COMMAND PARAMETER
RETURN
BLACK SCREEN ON
I M B K _ _ _ 1 OK OR ERR
BLACK SCREEN OFF
I M B K _ _ _ 0 OK OR ERR
INPUT 1 (RGB 1)
I R G B _ _ _ 1 OK OR ERR
INPUT 2 (RGB 2)
I R G B _ _ _ 2 OK OR ERR
INPUT 3 (RGB 3)
I R G B _ _ _ 3 OK OR ERR
INPUT 4 (VIDEO 1)
I V E D _ _ _ 1 OK OR ERR
INPUT 5 (VIDEO 2)
I V E D _ _ _ 2 OK OR ERR
INPUT CHECK
I C H K _ _ _ 0 OK OR ERR
FREEZE ON
F R E Z _ _ _ 1 OK OR ERR
FREEZE OFF
F R E Z _ _ _ 0 OK OR ERR
AUTO SYNC START
A D J S _ _ _ 1 OK OR ERR
(RS-232C) Specifications and Command Settings
COMMAND PARAMETER
RETURN
CONTROL CONTENTS
COMMAND PARAMETER
RETURN
INPUT 1 (RGB 1) SIGNAL TYPE : RGB
I A S I _ _ _ 0 OK OR ERR
INPUT 1 (RGB 1) RESIZE : FULL
R A S R _ _ _ 5 OK OR ERR
INPUT 1 (RGB 1) SIGNAL TYPE : COMPONENT
I A S I _ _ _ 1 OK OR ERR
INPUT 1 (RGB 1) RESIZE : DOT BY DOT
R A S R _ _ _ 3 OK OR ERR
INPUT 2 (RGB 2) SIGNAL TYPE : RGB
I B S I _ _ _ 0 OK OR ERR
INPUT 2 (RGB 2) RESIZE : NORMAL
R B S R _ _ _ 1 OK OR ERR
INPUT 2 (RGB 2) SIGNAL TYPE : COMPONENT
I B S I _ _ _ 1 OK OR ERR
INPUT 2 (RGB 2) RESIZE : FULL
R B S R _ _ _ 5 OK OR ERR
INPUT 1 (RGB 1) 2D PROGRESSIVE
R A I P _ _ _ 0 OK OR ERR
INPUT 2 (RGB 2) RESIZE : DOT BY DOT
R B S R _ _ _ 3 OK OR ERR
INPUT 1 (RGB 1) 3D PROGRESSIVE
R A I P _ _ _ 1 OK OR ERR
INPUT 3 (RGB 3) RESIZE : NORMAL
R C S R _ _ _ 1 OK OR ERR
INPUT 1 (RGB 1) Film MODE
R A I P _ _ _ 2 OK OR ERR
INPUT 3 (RGB 3) RESIZE : FULL
R C S R _ _ _ 5 OK OR ERR
INPUT 2 (RGB 2) 2D PROGRESSIVE
R B I P _ _ _ 0 OK OR ERR
INPUT 3 (RGB 3) RESIZE : DOT BY DOT
R C S R _ _ _ 3 OK OR ERR
INPUT 2 (RGB 2) 3D PROGRESSIVE
R B I P _ _ _ 1 OK OR ERR
INPUT 4 (VIDEO 1) RESIZE : NORMAL
R A S V _ _ _ 1 OK OR ERR
INPUT 2 (RGB 2) Film MODE
R B I P _ _ _ 2 OK OR ERR
INPUT 4 (VIDEO 1) RESIZE : FULL
R A S V _ _ _ 5 OK OR ERR
INPUT 3 (RGB 3) 2D PROGRESSIVE
R C I P _ _ _ 0 OK OR ERR
INPUT 4 (VIDEO 1) RESIZE : BORDER
R A S V _ _ _ 3 OK OR ERR
INPUT 3 (RGB 3) 3D PROGRESSIVE
R C I P _ _ _ 1 OK OR ERR
INPUT 4 (VIDEO 1) RESIZE : STRETCH
R A S V _ _ _ 2 OK OR ERR
INPUT 3 (RGB 3) Film MODE
R C I P _ _ _ 2 OK OR ERR
INPUT 4 (VIDEO 1) RESIZE : SMART STRETCH
R A S V _ _ _ 4 OK OR ERR
INPUT 4 (VIDEO 1) CONTRAST (30 – 30)
V A P I _ * * * OK OR ERR
INPUT 5 (VIDEO 2) RESIZE : NORMAL
R B S V _ _ _ 1 OK OR ERR
INPUT 4 (VIDEO 1) BRIGHT (30 – 30)
V A B R _ * * * OK OR ERR
INPUT 5 (VIDEO 2) RESIZE : FULL
R B S V _ _ _ 5 OK OR ERR
INPUT 4 (VIDEO 1) RED (30 – 30)
V A R D _ * * * OK OR ERR
INPUT 5 (VIDEO 2) RESIZE : BORDER
R B S V _ _ _ 3 OK OR ERR
INPUT 4 (VIDEO 1) BLUE (30 – 30)
V A B E _ * * * OK OR ERR
INPUT 5 (VIDEO 2) RESIZE : STRETCH
R B S V _ _ _ 2 OK OR ERR
INPUT 4 (VIDEO 1) COLOR (30 – 30)
V A C O _ * * * OK OR ERR
INPUT 5 (VIDEO 2) RESIZE : SMART STRETCH
R B S V _ _ _ 4 OK OR ERR
INPUT 4 (VIDEO 1) TINT (30 – 30)
V A T I _ * * * OK OR ERR
RGB GAMMA : STANDARD
G A M R _ _ _ 1 OK OR ERR
INPUT 4 (VIDEO 1) SHARP (30 – 30)
V A S H _ * * * OK OR ERR
RGB GAMMA : PRESENTATION
G A M R _ _ _ 2 OK OR ERR
INPUT 4 (VIDEO 1) CLR TEMP (3 – 3)
V A C T _ _ * * OK OR ERR
RGB GAMMA : CINEMA
G A M R _ _ _ 3 OK OR ERR
INPUT 4 (VIDEO 1) DISPLAY
V A R E _ _ _ 0 OK OR ERR
RGB GAMMA : CUSTOM
G A M R _ _ _ 4 OK OR ERR
INPUT 4 (VIDEO 1) ADJUSTMENT RESET
V A R E _ _ _ 1 OK OR ERR
VIDEO GAMMA : STANDARD
G A M V _ _ _ 1 OK OR ERR
INPUT 5 (VIDEO 2) CONTRAST (30 – 30)
V B P I _ * * * OK OR ERR
VIDEO GAMMA : PRESENTATION
G A M V _ _ _ 2 OK OR ERR
INPUT 5 (VIDEO 2) BRIGHT (30 – 30)
V B B R _ * * * OK OR ERR
VIDEO GAMMA : CINEMA
G A M V _ _ _ 3 OK OR ERR
INPUT 5 (VIDEO 2) RED (30 – 30)
V B R D _ * * * OK OR ERR
VIDEO GAMMA : CUSTOM
G A M V _ _ _ 4 OK OR ERR
INPUT 5 (VIDEO 2) BLUE (30 – 30)
V B B E _ * * * OK OR ERR
INPUT 1 (RGB 1) CONTRAST (30 – 30)
R A P I _ * * * OK OR ERR
INPUT 5 (VIDEO 2) COLOR (30 – 30)
V B C O _ * * * OK OR ERR
INPUT 1 (RGB 1) BRIGHT (30 – 30)
R A B R _ * * * OK OR ERR
INPUT 5 (VIDEO 2) TINT (30 – 30)
V B T I _ * * * OK OR ERR
INPUT 1 (RGB 1) RED (30 – 30)
R A R D _ * * * OK OR ERR
INPUT 5 (VIDEO 2) SHARP (30 – 30)
V B S H _ * * * OK OR ERR
INPUT 1 (RGB 1) BLUE (30 – 30)
R A B E _ * * * OK OR ERR
INPUT 5 (VIDEO 2) CLR TEMP (3 – 3)
V B C T _ _ * * OK OR ERR
INPUT 1 (RGB 1) COLOR (30 – 30)
R A C O _ * * * OK OR ERR
INPUT 5 (VIDEO 2) DISPLAY
V B R E _ _ _ 0 OK OR ERR
INPUT 1 (RGB 1) TINT (30 – 30)
R A T I _ * * * OK OR ERR
INPUT 5 (VIDEO 2) ADJUSTMENT RESET
V B R E _ _ _ 1 OK OR ERR
INPUT 1 (RGB 1) SHARP (30 – 30)
R A S H _ * * * OK OR ERR
INPUT 4 (VIDEO 1) 2D PROGRESSIVE
V A I P _ _ _ 0 OK OR ERR
INPUT 1 (RGB 1) CLR TEMP (3 – 3)
R A C T _ _ * * OK OR ERR
INPUT 4 (VIDEO 1) 3D PROGRESSIVE
V A I P _ _ _ 1 OK OR ERR
INPUT 1 (RGB 1) DISPLAY
R A R E _ _ _ 0 OK OR ERR
INPUT 4 (VIDEO 1) Film MODE
V A I P _ _ _ 2 OK OR ERR
INPUT 1 (RGB 1) ADJUSTMENT RESET
R A R E _ _ _ 1 OK OR ERR
INPUT 5 (VIDEO 2) 2D PROGRESSIVE
V B I P _ _ _ 0 OK OR ERR
INPUT 2 (RGB 2) CONTRAST (30 – 30)
R B P I _ * * * OK OR ERR
INPUT 5 (VIDEO 2) 3D PROGRESSIVE
V B I P _ _ _ 1 OK OR ERR
INPUT 2 (RGB 2) BRIGHT (30 – 30)
R B B R _ * * * OK OR ERR
INPUT 5 (VIDEO 2) Film MODE
V B I P _ _ _ 2 OK OR ERR
INPUT 2 (RGB 2) RED (30 – 30)
R B R D _ * * * OK OR ERR
(INPUT 1–5) 2D PROGRESSIVE
I M I P _ _ _ 0 OK OR ERR
INPUT 2 (RGB 2) BLUE (30 – 30)
R B B E _ * * * OK OR ERR
(INPUT 1–5) 3D PROGRESSIVE
I M I P _ _ _ 1 OK OR ERR
INPUT 2 (RGB 2) COLOR (30 – 30)
R B C O _ * * * OK OR ERR
(INPUT 1–5) Film MODE
I M I P _ _ _ 2 OK OR ERR
INPUT 2 (RGB 2) TINT (30 – 30)
R B T I _ * * * OK OR ERR
CLOCK (150 – 150)
I N C L * * * * OK OR ERR
INPUT 2 (RGB 2) SHARP (30 – 30)
R B S H _ * * * OK OR ERR
PHASE (60 – 60)
I N P H _ * * * OK OR ERR
INPUT 2 (RGB 2) CLR TEMP (3 – 3)
R B C T _ _ * * OK OR ERR
H-POSITION (150 – 150)
I A H P * * * * OK OR ERR
INPUT 2 (RGB 2) DISPLAY
R B R E _ _ _ 0 OK OR ERR
V-POSITION (60 – 60)
I A V P _ * * * OK OR ERR
INPUT 2 (RGB 2) ADJUSTMENT RESET
R B R E _ _ _ 1 OK OR ERR
RGB INPUT DISPLAY
I A R E _ _ _ 0 OK OR ERR
INPUT 3 (RGB 3) CONTRAST (30 – 30)
R C P I _ * * * OK OR ERR
RGB ADJUSTMENT RESET
I A R E _ _ _ 1 OK OR ERR
INPUT 3 (RGB 3) BRIGHT (30 – 30)
R C B R _ * * * OK OR ERR
SAVE SETTING (1 – 7)
M E M S _ _ _ * OK OR ERR
SELECT SETTING (1 – 7)
M E M L _ _ _ * OK OR ERR
RGB HORIZONTAL FREQUENCY CHECK
T F R Q _ _ _ 1 kHz (***. * OR _)
PICTURE
R A S R _ _ _ 1 OK OR ERR
FINE SYNC *1
PICTURE
BUTTONS & REMOTE CONTROL KEY
CONTROL CONTENTS
INPUT 1 (RGB 1) RESIZE : NORMAL
INPUT 3 (RGB 3) RED (30 – 30)
R C R D _ * * * OK OR ERR
INPUT 3 (RGB 3) BLUE (30 – 30)
R C B E _ * * * OK OR ERR
INPUT 3 (RGB 3) COLOR (30 – 30)
R C C O _ * * * OK OR ERR
RGB VERTICAL FREQUENCY CHECK
T F R Q _ _ _ 2 Hz (***. * OR _)
INPUT 3 (RGB 3) TINT (30 – 30)
R C T I _ * * * OK OR ERR
AUTO SYNC OFF
A A D J _ _ _ 0 OK OR ERR
R C C H _ * * * OK OR ERR
NORMAL AUTO SYNC
A A D J _ _ _ 1 OK OR ERR
R C C T _ _ * * OK OR ERR
HIGH SPEED AUTO SYNC
A A D J _ _ _ 2 OK OR ERR
INPUT 3 (RGB 3) DISPLAY
R C R E _ _ _ 0 OK OR ERR
AUTO SYNC DISPLAY ON
I M A S _ _ _ 1 OK OR ERR
INPUT 3 (RGB 3) ADJUSTMENT RESET
R C R E _ _ _ 1 OK OR ERR
AUTO SYNC DISPLAY OFF
I M A S _ _ _ 0 OK OR ERR
Appendix
INPUT 3 (RGB 3) SHARP (30 – 30)
INPUT 3 (RGB 3) CLR TEMP (3 – 3)
E-74
(RS-232C) Specifications and Command Settings
COMMAND PARAMETER
CONTROL CONTENTS
RETURN
A A B L _ * * * OK OR ERR
COMMAND PARAMETER
RETURN
LAMP USAGE TIME
T L T T _ _ _ 1 0–9999 (INTEGER)
LAMP STATUS
T L P S _ _ _ 1
A A T E _ * * * OK OR ERR
A A B A _ * * * OK OR ERR
AUDIO DISPLAY
A A R E _ _ _ 0 OK OR ERR
PRJ MODE : REVERSE OFF
I M R E _ _ _ 0 OK OR ERR
AUDIO ADJUSTMENT RESET
A A R E _ _ _ 1 OK OR ERR
PRJ MODE : REVERSE ON
I M R E _ _ _ 1 OK OR ERR
FAO
A O U T _ _ _ 1 OK OR ERR
PRJ MODE : INVERT OFF
I M I N _ _ _ 0 OK OR ERR
VAO
A O U T _ _ _ 2 OK OR ERR
PRJ MODE : INVERT ON
I M I N _ _ _ 1 OK OR ERR
SPEAKER ON
A S P K _ _ _ 1 OK OR ERR
STACK SETTING : NORMAL
S T A K _ _ _ 0 OK OR ERR
SPEAKER OFF
A S P K _ _ _ 0 OK OR ERR
STACK SETTING : MASTER
S T A K _ _ _ 1 OK OR ERR
PICT IN PICT : BOTTOM RIGHT
P I N P _ _ 1 1 OK OR ERR
STACK SETTING : SLAVE
S T A K _ _ _ 2 OK OR ERR
PICT IN PICT : BOTTOM LEFT
P I N P _ _ 1 2 OK OR ERR
KEYLOCK LEVEL : NORMAL
K E Y L _ _ _ 0 OK OR ERR
PICT IN PICT : UPPER RIGHT
P I N P _ _ 1 3 OK OR ERR
KEYLOCK LEVEL : LEVEL A
K E Y L _ _ _ 1 OK OR ERR
PICT IN PICT : UPPER LEFT
P I N P _ _ 1 4 OK OR ERR
PICT IN PICT RESET
P I N P _ _ _ 0 OK OR ERR
VIDEO DNR OFF
VIDEO DNR ON
OPTIONS (2)
TREBLE (30 – 30)
BASS (30 – 30)
0:OFF, 1:ON, 2:RETRY,
3:WAITING, 4:LAMP ERROR
KEYLOCK LEVEL : LEVEL B
K E Y L _ _ _ 2 OK OR ERR
SET INPUTS : INPUT 1 NO USE
R A S I _ _ _ 0 OK OR ERR
3 D N R _ _ _ 0 OK OR ERR
SET INPUTS : INPUT 1 USE
R A S I _ _ _ 1 OK OR ERR
3 D N R _ _ _ 1 OK OR ERR
SET INPUTS : INPUT 2 NO USE
R B S I _ _ _ 0 OK OR ERR
OSD DISPLAY ON
I M D I _ _ _ 1 OK OR ERR
SET INPUTS : INPUT 2 USE
R B S I _ _ _ 1 OK OR ERR
OSD DISPLAY OFF (LEVEL A)
I M D I _ _ _ 2 OK OR ERR
SET INPUTS : INPUT 3 NO USE
R C S I _ _ _ 0 OK OR ERR
OSD DISPLAY OFF (LEVEL B)
I M D I _ _ _ 0 OK OR ERR
SET INPUTS : INPUT 3 USE
R C S I _ _ _ 1 OK OR ERR
BLACK SCREEN DISPLAY ON
I M B O _ _ _ 1 OK OR ERR
SET INPUTS : INPUT 4 NO USE
V A S I _ _ _ 0 OK OR ERR
BLACK SCREEN DISPLAY OFF
I M B O _ _ _ 0 OK OR ERR
SET INPUTS : INPUT 4 USE
V A S I _ _ _ 1 OK OR ERR
VIDEO SYSTEM SELECTION : AUTO
M E S Y _ _ _ 1 OK OR ERR
SET INPUTS : INPUT 5 NO USE
V B S I _ _ _ 0 OK OR ERR
VIDEO SYSTEM SELECTION : PAL
M E S Y _ _ _ 2 OK OR ERR
SET INPUTS : INPUT 5 USE
V B S I _ _ _ 1 OK OR ERR
VIDEO SYSTEM SELECTION : SECAM
M E S Y _ _ _ 3 OK OR ERR
ID NO. CHECK
R D I D _ _ _ 1 001–250
VIDEO SYSTEM SELECTION : NTSC4.43
M E S Y _ _ _ 4 OK OR ERR
LANGUAGE SELECTION : ENGLISH
M E L A _ _ _ 0 OK OR ERR
VIDEO SYSTEM SELECTION : NTSC3.58
M E S Y _ _ _ 5 OK OR ERR
LANGUAGE SELECTION : DEUTSCH
M E L A _ _ _ 1 OK OR ERR
VIDEO SYSTEM SELECTION : PAL_M
M E S Y _ _ _ 6 OK OR ERR
LANGUAGE SELECTION : ESPAÑOL
M E L A _ _ _ 2 OK OR ERR
VIDEO SYSTEM SELECTION : PAL_N
M E S Y _ _ _ 7 OK OR ERR
LANGUAGE SELECTION : NEDERLANDS
M E L A _ _ _ 3 OK OR ERR
BACKGROUND SELECTION : SHARP
I M B G _ _ _ 1 OK OR ERR
LANGUAGE SELECTION : FRANÇAIS
M E L A _ _ _ 4 OK OR ERR
BACKGROUND SELECTION : CUSTOM
I M B G _ _ _ 2 OK OR ERR
LANGUAGE SELECTION : ITALIANO
M E L A _ _ _ 5 OK OR ERR
BACKGROUND SELECTION : BLUE
I M B G _ _ _ 3 OK OR ERR
LANGUAGE SELECTION : SVENSKA
M E L A _ _ _ 6 OK OR ERR
BACKGROUND SELECTION : NONE
I M B G _ _ _ 4 OK OR ERR
LANGUAGE SELECTION :
M E L A _ _ _ 7 OK OR ERR
STARTUP IMAGE SELECTION : SHARP
I M S I _ _ _ 1 OK OR ERR
LANGUAGE SELECTION : PORTUGUÊS
M E L A _ _ _ 8 OK OR ERR
STARTUP IMAGE SELECTION : CUSTOM
I M S I _ _ _ 2 OK OR ERR
LANGUAGE SELECTION :
M E L A _ _ _ 9 OK OR ERR
STARTUP IMAGE SELECTION : NONE
I M S I _ _ _ 3 OK OR ERR
LANGUAGE SELECTION :
M E L A _ _ 1 0 OK OR ERR
MONITOR OUT OFF
M O U T _ _ _ 0 OK OR ERR
MODEL NAME CHECK
M N R D _ _ _ 1 MODEL NAME
MONITOR OUT ON
M O U T _ _ _ 1 OK OR ERR
NOISE FILTER OFF
N F I L _ _ _ 0 OK OR ERR
AUTO POWER OFF : NO USE
A P O W _ _ _ 0 OK OR ERR
NOISE FILTER ON *2
N F I L _ _ _ 1 OK OR ERR
AUTO POWER OFF : USE
A P O W _ _ _ 1 OK OR ERR
SERIAL NO. CHECK *3
S N R D _ _ _ 1 SERIAL NO.
PROJECTOR NAME SETTING *4
P J N A _ _ _ 1 OK OR ERR
PROJECTOR NAME CHECK
P J N A _ _ _ 2 PROJECTOR NAME
LANGUAGE
OPTIONS (1)
AUDIO
CONTROL CONTENTS
BALANCE (30 – 30)
Appendix
• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the range
indicated in brackets under CONTROL CONTENTS.
• *1 FINE SYNC can only be set in the displayed RGB mode.
• *2 Noise may appear when used with certain computers. Set the NOISE FILTER to ON using the RS-232C command.
• *3 SERIAL NO. CHECK command is used to read out the 12 digits of serial No..
• *4 After OK is returned, enter PROJECTOR NAME, up to 12-character memory. The PROJECTOR NAME in memory can then
be output (confirmed).
E-75
Wired Remote Control Terminal Specifications
Specifications of wired remote control input
• ø3.5 mm minijack
• External: 5 V (1 A)
• Internal: GND
Function and transmission codes
SYSTEM CODE
CONTROL
ITEM
EXTERNAL
CODE
DATA CODE
SYSTEM CODE
CONTROL
ITEM
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15
EXTERNAL
CODE
DATA CODE
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15
ON
1
0
1
1
0
0
1
1
0
1
0
1
0
1
0
Freeze
1
0
1
1
0
1
0
1
1
0
0
0
1
1
0
OFF
1
0
1
1
0
0
1
1
0
1
0
0
1
1
0
Enlarge
1
0
1
1
0
1
0
1
1
0
1
1
0
1
0
VOLUME 1
0
1
1
0
0
0
1
0
1
0
0
0
1
0
AUTO SYNC
1
0
1
1
0
0
1
0
1
1
1
1
1
1
0
VOLUME 1
0
1
1
0
1
0
1
0
1
0
0
0
1
0
∂
1
0
1
1
0
0
0
1
1
1
0
0
1
1
0
MUTE
1
0
1
1
0
1
1
1
0
1
0
0
0
1
0
ƒ
1
0
1
1
0
1
0
1
1
1
0
0
1
1
0
MENU
1
0
1
1
0
0
0
1
0
0
0
1
1
1
0
ß
1
0
1
1
0
0
0
0
0
1
0
1
0
1
0
LENS
1
0
1
1
0
1
1
0
1
0
0
0
1
1
0
©
1
0
1
1
0
1
1
1
1
0
0
1
0
1
0
BLACK SCREEN 1
0
1
1
0
1
0
0
1
0
1
1
0
1
0
GAMMA
1
0
1
1
0
0
0
0
0
0
0
1
0
1
0
ENTER
1
0
1
1
0
1
1
1
0
1
0
1
0
1
0
INPUT 1. 2. 3
1
0
1
1
0
0
0
1
1
0
1
1
1
1
0
RESIZE
1
0
1
1
0
0
1
1
1
1
0
1
0
1
0
INPUT 4. 5
1
0
1
1
0
0
1
1
0
1
1
0
1
1
1
UNDO
1
0
1
1
0
1
0
0
1
1
0
1
0
1
0
Wired remote control function code
• To operate the mouse, left-click and right-click functions
through the wired remote control input, connect the cable
from the WIRED REMOTE control input terminal on the
projector to the remote control. The codes for these functions
are complex and are, therefore, not listed here.
LSB
C1
1
MSB
System Code
C5
C6
1
0
*
0
1
Data Code
*
*
*
*
*
C13
C14
C15
*
1
0
*
• System codes C1 to C5 are fixed at “10110”.
• Codes C14 and C15 are reverse confirmation bits, with “10”
indicating “Front” and “01” indicating “Rear”.
Sharp remote control signal format
Transmission format: 15-bit format
D
D
D
D
D
D
67.5 ms
D
D
D
D
D
D
D
67.5 ms
Wave form of output signal: Output using Pulse Position Modulation
t
T1
T0
“1”
“0”
26.4 µs
“0”
“0”
“0”
“1”
“0”
t
D
• t 264 µs
• T0 1.05 ms
• T1 2.10 ms
• Pulse carrier frequency 455/12 kHz
• Duty ratio 1:1
Transmission control code
15 bit
C1
C2
C3
C4
System Address
C6
C7
C8
C9
Example of Reverse D to
C10
Function Key Data Bit
C11
C12
C13
Data
Expansion
C14
Mask
C15
Data
Determination
D
D
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
1
0
1
1
0
1
0
0
0
0
0
0
0
1
0
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
1
0
1
1
0
0
1
1
1
1
1
1
1
0
1
Appendix
D to D Common Data Bit
C5
Reverse in D
E-76
Computer Compatibility Chart
Horizontal Frequency: 15–126 kHz
Vertical Frequency: 43–200 Hz
Pixel Clock: 12–230 MHz
Compatible with sync on green and composite sync signals
UXGA and SXGA compatible in advanced intelligent compression or intelligent compression
AICS (Advanced Intelligent Compression and Expansion System) resizing technology
PC/
MAC/
WS
Resolution
640 350
720 350
640 400
720 400
VGA
640 480
PC
SVGA
XGA
800 600
1,024 768
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
60
54.3
60
70
64.0
70
PC/
MAC/
WS
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
27.0
31.5
37.9
85
27.0
60
31.5
70
27.0
60
77.3
85
31.5
70
90.2
100
37.9
85
111.1
120
27.0
60
54.8
60
31.5
70
65.9
72
37.9
85
67.4
74
26.2
50
31.5
60
34.7
70
37.9
72
37.5
75
91.1
85
43.3
85
108.4
100
74.7
52
47.9
90
53.0
100
VESA
Standard
Display
Resolution
1,152 864
SXGA
1,152 882
PC
1,280 1,024
Upscale
64.1
72
67.5
75
75.7
80
64.0
60
74.6
70
78.1
74
75.7
75
VESA
Standard
Advanced
Intelligent
Compression
61.8
120
75.0
60
78.5
150
81.3
65
80.9
160
87.5
70
100.4
200
90.1
72
31.4
50
35.1
56
37.9
60
44.5
70
48.1
72
46.9
75
53.7
85
56.8
90
64.0
100
77.2
120
UXGA 1,600 1,200
PC/
MAC 13"
VGA
640 480
PC/
MAC 19"
XGA
1,024 768
PC/
MAC 21"
SXGA 1,280 1,024
MAC 16"
SVGA
832 624
93.8
75
106.3
85
34.9
67
48.4
60
60.0
75
80.0
75
46.8
75
49.6
75
98.3
150
MAC 21"
SXGA 1,152 870
68.5
75
102.1
160
HP (WS)
1,280 1,024
78.1
72
125.6
200
PC (WS)
35.5
43
40.3
50
56.5
70
58.1
72
68.7
85
73.5
90
77.2
96
80.6
100
98.8
120
113.2
140
125.6
150
1,280 960
WS
SGI (WS)
SUN (WS)
SXGA
1,280 1,024
1,152 900
60.0
60
85.9
85
53.5
50
76.8
72
60.9
66
71.9
76
Display
Intelligent
Compression
Upscale
True
Advanced
Intelligent
Compression
Upscale
Advanced
Intelligent
Compression
True
Appendix
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this
occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how
to change display modes can be found in your notebook computer’s operation manual.
• This projector can receive 640 350 VESA format VGA signals, however, “640 400” will appear on the screen.
• When receiving 1,600 1,200 VESA format UXGA signals, sampling occurs and the image is displayed with 1,024 lines,
causing part of the image to be blocked.
E-77
Dimensions
Rear View
Side View
Top View
11 3/25 (282.5)
6 3/32 (155)
12 9/16 (319)
9 32
/ (7)
1 8
/ (3)
17 15/64 (438)
16 21/32 (423)
3 1/6 (79)
Side View
9
/64 (3.5)
29 32
/ (23)
4 37/64 (116.5) 2 9/16 (65)
Front View
1 3/64 (26.5)
1 11/32 (34)
9 / (248)
3 4
Bottom View
Appendix
Units: inches (mm)
E-78
Specifications
Product type LCD Projector
Model XG-P20XU
Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480P/720P/1080i
Display method LCD panel 3, RGB optical shutter method
LCD panel Panel size: 1.3 (20.0 [H] 26.6 [W] mm)
Display method: Translucent TN liquid crystal panel
Drive method: TFT (Thin Film Transistor) Active Matrix panel
No. of dots: 786,432 dots (1,024 [H] 768 [V])
Standard Lens 1–1.3 zoom lens, F1.7–2.3, f = 49.1–63.8 mm
Projection lamp AC 220 W lamp
Contrast ratio 600:1
Video input signal RCA Connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω terminated
RCA Connector: AUDIO, 0.5 Vrms more than 22 kΩ (stereo)
S-video input signal 4-pin Mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Component input signal BNC Connector (INPUT 2)
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
Horizontal resolution 520 TV lines (S-video input), 750 TV lines (DTV 720P input, STRETCH mode)
RGB input signal 15-PIN MINI D-SUB CONNECTOR (INPUT 1), 5 BNC CONNECTOR (INPUT 2):
RGB separate/composite sync/sync on green type analog input: 0–0.7 Vp-p, positive,
75 Ω terminated
DVI CONNECTOR (29-PIN) (INPUT 3), RGB (DIGITAL), 250–1,000 mV, 50 Ω
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) or composite sync (Apple only)
VERTICAL SYNC. SIGNAL: Same as above
STEREO MINIJACK: AUDIO, 0.5 Vrms, more than 22 kΩ (stereo)
Pixel clock 12–230 MHz
Vertical frequency 43–200 Hz
Horizontal frequency 15–126 kHz
Computer control signal 9-pin D-sub connector (RS-232C Input Port/Output Port)
Speaker system 1 49⁄64 (4.5 cm) round 2
2 W 2 W (stereo)
Rated voltage AC 100–240 V
Input current 3.95 A
Rated frequency 50/60 Hz
Power consumption 330 W
Power dissipation < 1,250 BTU/hour
Operating temperature 41°F to 104°F (5°C to 40°C)
Storage temperature 4°F to 140°F (20°C to 60°C)
Cabinet Plastic
GyroRemote Radio Frequency Range: 49.825–49.895 MHz
Dimensions (approx.) 12 9⁄16 (W) 6 3⁄32 (H) 16 21⁄32 (D) (319.0 155.0 423.0 mm) (main body only)
12 11⁄32 (W) 7 27⁄64 (H) 17 15⁄64 (D) (322.5 188.5 438.0 mm) (including standard
lens, adjustment feet and projecting parts)
Weight (approx.) 21.0 lbs. (9.5 kg)
Supplied accessories GyroRemote, Four AAA size batteries, Power cord (11 10, 3.6 m), RGB cable (9 10,
3 m), USB mouse control cable (3 3, 1 m), Computer audio cable (9 10, 3 m), ø2.5–ø3.5
mm wired remote control cable (6 45⁄64, 15 cm), Three BNC-RCA adaptors, Extra air filter,
Lens cap, CD-ROM, LCD projector operation manual, LCD projector quick guide, Sharp
Advanced Presentation Software operation manual, ID number seal
Replacement parts Standard lens unit (CLNS-0236CE01), Lamp unit (Lamp/cage module) (BQC-XGP20X//1),
GyroRemote (RRMCG1631CESA), AAA size batteries, Power cord (QACCU5013DE01),
RGB cable (QCNW-5304CEZZ), USB mouse control cable (QCNW-5916CEZZ), Computer
audio cable (QCNW-4870CEZZ), ø2.5–ø3.5 mm wired remote control cable (QCNW5943CEZZ), BNC-RCA adaptors (QPLGJ0107GEZZ), Air filter (PFILD0080CEZZ), Lens cap
(PCAPH1056CESA), CD-ROM (UDSKA0043CEN1), LCD projector operation manual (TINS7354CEZZ), LCD projector quick guide (TINS-7355CEZZ), Sharp Advanced Presentation
Software operation manual (TINS-7356CEZZ), ID number seal (TLABZ0781CEZZ)
Appendix
This SHARP projector uses LCD (Liquid Crystal Display) panels. These
very sophisticated panels contain 786,432 pixels ( RGB) TFTs (Thin
Film Transistors). As with any high technology electronic equipment
such as large screen TVs, video systems and video cameras, there
are certain acceptable tolerances that the equipment must conform
to.
This unit has some inactive TFTs within acceptable tolerances which
may result in illuminated or inactive dots on the picture screen. This
will not affect the picture quality or the life expectancy of the unit.
If you have any questions about this matter, please call toll free 1-888GO-SHARP (1-888-467-4277). U.S.A. ONLY
Specifications are subject to change without notice.
E-79
Glossary
Aspect ratio
Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3. There are also wide images with an aspect ratio of 16:9 and
21:9.
Auto Sync
Optimizes projected computer images by automatically adjusting certain characteristics.
Background
Initial setting image projected when no signal is being input.
Border
Displays the 4:3 image as the biggest size (768576) that can be displayed on the WIDE mode screen (1024576).
Clock
Clock adjustment is used to adjust vertical noise when clock level is incorrect.
CLR Temp (Color temperature)
Function that can be used to adjust the color temperature to suit the type of image input to the projector. Decrease the color temperature to create warmer,
reddish images for natural flesh tones, or increase to create cooler, bluish images for a brighter picture.
Composite sync
Signal combining horizontal and vertical sync pulses.
Digital shift
Shifts image up or down easily by ∂/ƒ buttons when RESIZE mode of input image is BORDER, STRETCH or SMART STRETCH of COMPUTER (except for
SXGA and UXGA), VIDEO and DTV inputs.
DNR (Digital Noise Reduction)
Provides high quality images with minimal dot crawl and cross color noise.
Dot by dot
Mode that projects images in their native resolution.
DVI
Digital Visual Interface that supports both digital and analog displays.
GAMMA
Image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter
portions. You can select four different modes : STANDARD, PRESENTATION, CINEMA and CUSTOM.
GyroRemote
Remote control device with a built-in sensor that can operate projectors and computers. GyroRemote communicates with a projector via radio signals and
therefore does not encounter the line-of-sight problems found in infrared devices.
Intelligent compression and expansion
High quality resizing of lower and higher resolution images to fit the projector’s native resolution.
Intelligent digital keystone correction
Function to digitally correct a distorted image when the projector is set up at an angle, smooths out jaggies on keystone images and compresses the image not
only horizontally but vertically keeping the 4:3 aspect ratio, and at the same time, calculates the aspect ratio automatically adjusting to the lens shift width.
Keylock level
Mode that can lock the operation of projector buttons to prevent mischief.
Lens shift
The lens can be easily raised and lowered to minimize or eliminate “Keystone” type effect.
Magnification (Enlarge)
Digitally zooms in on a portion of an image.
Phase
Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontal
flicker.
Picture in Picture
Allows you to add video images onto a data screen image, providing you with even more effective presentations.
Presentation tools
Helpful tools used to emphasize keypoints throughout a presentation.
Progressive Mode
The progressive display projects a smoother video image. You can select three different modes : 2D Progressive, 3D Progressive and Film Mode.
RESIZE
Allows you to modify or customize the picture display mode to enhance the input image. You can select six different modes: NORMAL, FULL, DOT BY DOT,
BORDER, STRETCH and SMART STRETCH.
RS-232C
Function to control the projector from the computer by using the RS-232C ports on the projector and computer.
Set Inputs
Function to limit inputs. For example, when setting Input 2 to “OFF”, the input is switchable only between Input 1 and Input 3, skipping Input 2.
Smart Stretch
Mode that stretches the right and left sides of the 4:3 image horizontally while maintaining the aspect ratio around the center of the image to display it on the WIDE
screen.
Stack Setting
Prevents trouble with adjustment and operation when stack projecting. When setting two projectors, one to master and the other to slave, the slave follows the
master’s operation.
Appendix
Status function
Displays the settings of each adjustment item.
Stretch
Mode that stretches the 4:3 image horizontally to display it on the WIDE screen.
Sync on green
Video signal mode of a computer which overlaps horizontal and vertical sync signal to green color signal pin.
E-80
Index
A
AC socket ........................................................................
Adjusting the Picture .......................................................
Adjustment Feet ..............................................................
Air filter ............................................................................
Aspect ratio .....................................................................
ASSIGN Select button .....................................................
Audio ...............................................................................
Audio cable .....................................................................
AUDIO INPUT terminal ...................................................
AUDIO OUTPUT terminal ................................................
Auto sync adjustment .....................................................
AUTO SYNC button .........................................................
N
13
47
20
70
42
33
52
18
14
18
51
51
B
Background ....................................................................
BLACK SCREEN button ..................................................
BNC-RCA adaptors .........................................................
BORDER .........................................................................
55
40
18
42
C
Carrying handle ..............................................................
Ceiling-mount ..................................................................
Ceiling+Rear ...................................................................
Clock ...............................................................................
CLR Temp (Color Temperature) ......................................
4
29
57
49
47
D
Digital shift ......................................................................
DNR (Digital Noise Reduction) .......................................
DOT BY DOT ...................................................................
DVI INPUT port (INPUT 3) ...............................................
56
44
3
12
F
FAO ................................................................................. 52
Function button ............................................................... 33
G
GAMMA button ............................................................... 43
GUI (Graphical User Interface) ....................................... 44
GyroRemote .................................................................... 30
I
INPUT button ................................................................... 39
INPUT port ...................................................................... 14
Intelligent digital keystone correction ............................. 21
K
Keylock Levels ................................................................ 58
L
Appendix
LAMP REPLACEMENT indicator .....................................
LEARN button .................................................................
LEFT-CLICK button .........................................................
LENS button ....................................................................
Lens shift .........................................................................
67
37
35
21
20
M
MENU button ................................................................... 44
Monitor Out/RS-232C Off Function ................................. 56
MUTE button ................................................................... 39
E-81
O
On-screen display ........................................................... 54
On-screen display Language ......................................... 62
OUTPUT port .................................................................. 56
P
Password ........................................................................
PDF .................................................................................
Phase ..............................................................................
Picture in Picture .............................................................
POINTER button ..............................................................
POWER buttons ..............................................................
Power cord ......................................................................
POWER indicator ............................................................
Presentation tools ............................................................
Progressive Mode ...........................................................
61
9
49
53
32
19
13
13
34
48
R
Rear projection ................................................................
RESIZE button .................................................................
RF CH button ...............................................................
RGB cable .......................................................................
RIGHT-CLICK button .......................................................
RS-232C port ..................................................................
29
42
36
14
35
16
S
21
53
42
16
E
Economy Mode ...............................................................
ENTER button ..................................................................
Exhaust vent ....................................................................
Extra air filter ...................................................................
Network Function ............................................................ 63
Save Setting ....................................................................
Select Setting ..................................................................
Set ID No. ........................................................................
Set Inputs ........................................................................
Speaker ...........................................................................
Stack Setting ...................................................................
Startup image .................................................................
Status function ................................................................
S-VIDEO INPUT terminal .................................................
Sync ................................................................................
Sync on green .................................................................
49
49
60
59
52
58
55
62
17
51
72
T
TEACH button ................................................................. 37
TEMPERATURE WARNING indicator .............................. 67
Transmission Speed (RS-232C) ...................................... 59
U
UNDO button .................................................................. 44
USB mouse control cable ............................................... 35
V
VAO .................................................................................
VIDEO INPUT terminal ....................................................
Video System ..................................................................
Videowall .........................................................................
VOLUME buttons ............................................................
52
17
54
66
39
W
Wired remote control input .............................................. 38
WIRED REMOTE control input terminal .......................... 38
No.
1.2.3 button ..................................................................... 39
4.5 button ........................................................................ 39
SHARP CORPORATION