Miele DA 3180 Installation manual

Operating and Installation
Instructions
.....
_,_
_
!¸
Ventilation System
DA 31 60
DA 31 80
DA 31 90
To prevent accidents
and machine damage,
read these instructions
before
installation or use,
M-Nr, 06 593 190
Contents
iMPORTANT
Read these Operating
using the Ventilation
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
SAFETY
hstructions
System.
iiiiiiiiiii_iiiiiiiiiiiiiiiiiiiiiWiiiiiii_
This appliance is intended for
residential use only. Use the
appliance only for its intended
purpose. The manufacturer cannot
be held responsible for damages
caused by improper use of the
hood.
This appliance complies with current
safety requirements. Improper use of
the appliance can lead to personal
injury and material damage.
READ AND SAVE THESE
INSTRUCTIONS
carefully
ii
iNSTRUCTiONS
before
installing
or
This appliance is designed to vent
oook,
ngsmoke
and
odors
on,y.
Be
certa,n
your
app,iance
is by
properly
installed
and grounded
a qualified technician.
To guarantee the electrical safety of this
appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician. The manufacturer
cannot be held responsible for
damages caused by the lack, or
inadequacy, of an effective grounding
system.
Before connecting the appliance to
thepower
supp,y
make
sure
that
the voltage and frequency listed on the
data plate correspond with the
household electrical supply. This data
must correspond to prevent machine
damage. If in doubt consult a qualified
electrician.
Installation work and repairs should
only
beperformed
byaqua,
ified
technician in accordance with all
applicable codes and standards.
Repairs and other work by unqualified
persons could be dangerous and the
manufacturer will not be held
responsible.
iMPORTANT
SAFETY
iNSTRUCTiONS
This
equipment
isnot
maritime
use or for
usedesigned
in mobile for U,O
installations such as recreational
Do
notallow
toplay
or
operate
thechildren
appliance
or itswith
vehicles or aircraft. However, under
certain conditions it may be possible for
installation in these applications. Please
contact the nearest Miele dealer or the
Technical Service Department with
specific requirements.
i
Before servicing or cleaning the
unit,
d,soonnect
thehood
from
the
power supply by either removing the
fuse, unplugging it, or manually
"tripping" the circuit breaker.
Before discarding an old
appliance,
unp,ug
itfrom
the
power supply and remove the power
cord and any doors to prevent hazards.
controls. Supervise its use by the
elderly or infirm.
The halogen lamps become hot
during use. Keep children away.
Danger of burns.
Be careful
when the
preparing
flamb6
beneath
hood. a
Flames may be drawn up into the hood
by the suction and the grease filters
may catch fire.
Do not use the hood without the
grease filters in place.
Clean the grease filters regularly.
iiliii_iiiiXi!i_
Dirty filters are a fire hazard.
_,,_,_'_"_""_"_
Do
not
use
asteam
c,eaner
clean
the
hood.
Steam
could to
penetrate the electrical components
and cause a short circuit.
Always turn on the hood when
using the cooktop to prevent
damage from condensation.
iMPORTANT
z_ WARNmNG ° TO REDUCE
THE RmSK OF A COOKTOP
GREASE FRE:
Never leave surface units
unattended at high settings_
Boilovers cause smoking and greasy
spillovers may ignite, Heat oils slowly
on low or medium settings,
Always turn the hood on when
cook,ng
athigh
heat
orwhen
cooking flaming foods,
SAFETY
iNSTRUCTiONS
WARNING
TO REDUCE THE RISK OF INJURY
TO PERSONS IN THE EVENT OF A
COOKTOP GREASE FmRE,OBSERVE
THE FOLLOWmNG:
,,_,,,,_,,,,_
SMOT.ER
FLAMES
with
aclose
fitting lid, cookie sheet, or metal
tray, then turn off the burner,
BE CAREFUL TO PREVENT BURNS,
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
NEVER PICK UP A FLAMING
Clean
lation
fans
Greasevent,
should
not
be frequently_
allowed to
PAN_ou
may
beburned_
accumulate on the fan or filter,
Use the proper pan size, Always
use cookware appropriate for the
size of the surface elemenL
DO
NOT
USE
WATER,
including
wet dishcloths or towels - a violent
steam explosion may resulL
Use
afire
ONLY
if: extinguisher
-
You have a Class ABC extinguisher,
and know how to operate iL
-
The fire is small and contained in the
area where it started,
-
The fire department
-
You can fight the fire with your back
to an exiL
has been called,
iMPORTANT
SAFETY
iNSTRUCTiONS
mnstaHation
WA..,.G
To reduce the risk of fire onJy
use metal ductwork.
When installing the hood, follow the
recommended
m,n,mum
safety
distances between a Miele cooktop and
the hood:
-
18" (45 cm) above electric cooktops,
-
26" (65 cm) above gas cooktops,
-
26" (65 cm) above an open grill.
If local building codes require a greater
safety distance, follow their
requiremenL
For non-Miele cooking appliances
maintain the safety distances
recommended by the appliance
manufacturer,
If there is more than one appliance
beneath the hood and they have
different minimum safety distances
always select the greater distance.
When installing a custom front panel,
regard the cooktop manufacturer's
advice on the use of easily flammable
material above the cooktop.
Do not install this hood over
cooktops
burning
so,id
fue,_
Any fittings, sealant, or materials
used
toinstall
theduetwork
must
be made of approved non-flammable
materials.
iHliiiiDili_iilii
Never
connect
anexhaust
hood
to
an active chimney, dryer vent, flue,
or room ventilating ductwork. Seek
professional advice before connecting
an exhaust hood vent to an existing,
inactive chimney or flue.
Ducted fans must always be
_,ventedoutdoors,
Make sure that the airflow in the
room is sufficient for combustion
and exhausting of all non-electric
heating appliances (water heaters, gas
cooktops, gas ovens, etc.), otherwise
backdrafts may occur. Follow the
heating manufacturer's guidelines and
safety standards or those published by
the National Fire Protection Association
(NFPA), or the American Society for
Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE).
If in doubt, consult an experienced
professional.
Be
careful wiring
not to ordamage
hidden
electrical
plumbing
when
cutting or drilling into the wall or ceiling.
Do not use an extension cord to
connect
theappliance
toelectricity,
Extension cords do not guarantee the
required safety of the appliance, (e.g.
danger of overheating).
Functional
description
The ventilation hood offers two modes
of operation:
Air extraction
RecircuJation
mode
(recirculation installation kit available as
an optional accessory)
The air is drawn in and cleaned by the
grease filters and directed outside.
The hood comes equipped with a
non-return flap. The flap automatically
closes when the hood is turned off so
that no exchange of outside air and
room air can occun
Air is drawn through the grease filters
and an active charcoal filter. The
filtered air is then recirculated back into
the kitchen through a vent at the top of
the hood's chimney.
When the hood is turned on, the air
pressure of the exhaust fan
automatically opens the flap blowing
the inside air and cooking odors
outside.
Active charcoal filters may be
purchased from your Miele dealer or
Miele.
Before using the hood in
_; recirculation mode, ensure that the
active charcoal filte,[ is in place, see
Guide to the hood
ii •
I
•
•
\
Guide to the hood
_
Vent connection
Contro_
pane_
Grease
filter
E×pandab_e
Overhead
Active
fume deflector
cooktop
charcoa_
Hght
filter
Optional accessory for recirculation
mode
Facia Pane_
Accepts a custom front panel with the
DML 300 kit, optional accessory
On/Off
button
Power leve_ buttons
Four fan speed selection
@
Light
button
Operation
Turning
the fan on
Fan performance
[] Pull the deflector out.
The hood will operate at power level "2".
The On/Off indicator and the second
"-/+" indicator will lighL
Semecting the power
_eve_
Depending on how much the air needs
to be filtered, there are four power
levels available.
The maximum air flow capacity is
625 cfm. Factors such as narrow duct
diameter and bends will affect this
value.
Level
Level
Level
Level
1 operates
2 operates
3 operates
4 operates
The indicators show which power level
has been chosen.
For normal cooking a low to medium
level is usually sufficient.
For frying or cooking food with a strong
aroma use the highest level.
10
40% capacity
60% capacity
80% capacity
100% capacity
There will also be a slight decrease in
airflow for hoods operated in
recirculation mode due to the active
charcoal filter.
Turning
[] Use the "_/+" buttons to select the
power level required.
at
at
at
at
the fan off
[] Push the deflector back in.
The next time the deflector is pulled
out, the hood will operate on power
level "2".
or
[] Press the On/Off button to turn the
fan off.
The indicators go out.
Operation
Automatically
switching
intensive powe_ Jevel
back the
The intensive level "4" can be
programmed to automatically switch
back to level "3" after 10 minutes,
[] Turn the fan and the lights off,
Turning
the Hght on and off
The light for illuminating the cooktop
can be turned on or off independently
of the fan,
[] Pull the deflector out to turn the light
on, Push it in to turn it off,
or
[] Press and hold the "4+" buttons for
10 secs, The first indicator of the fan
power levels lights,
[] Press the following buttons one after
another
[] Press the light button,
When the light is turned on the indicator
next to the button illuminates,
[] Press the light button again,
-light,
The indicator will go out,
-
the"-"bu_on,
and
-
the light button again,
If the power level indicators flash the
automatic switch back is not activated,
[] To activate the automatic switch back
press the "+" button, The power level
indicators "1" and "4" lighL
[] To deactivate the automatic switch
back press the "-" button,
[] To save the setting press the On/Off
button,
11
Cleaning
and care
Casing
Before servicing or cleaning the
hood, disconnect it from the power
supply by "tripping" the circuit
breaker or unplugging iL
Make sure power is not restored to
the appliance while maintenance or
repair work is performed.
i' Never use abrasive cleaners,
!' scouring pads, steel wool or caustic
i" (oven) cleaners on the hood. They
[] All external surfaces and controls can
be cleaned with warm water and
liquid dish soap applied with a soft
sponge.
[] Wipe dry using a soft cloth.
Do not use too much water when
i:!
i cleaning the controls. Water could
!
ii penetrate the electronics and cause
Stainless
steel surfaces
(excluding the controls)
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel
cleaner,
To help prevent resoiling, a conditioner
for stainless steel can be applied.
Controls
regularly.
Do net use a stainless steel cleaner
on these controls.
12
Cleaning
Grease
fi_ter
and care
[] Cleaning the filter
The reusable metal grease filter
removes solid particles from the vented
kitchen air (grease, dust, etc).
-
by hand: with a nylon brush in a mild
solution of warm water and liquid
soap.
The grease filter should be cleaned
every 3 - 4 weeks.
-
in a dishwasher: place the filter
vertically in the lower basket,
checking that the spray arm is not
blocked.
:
e
............................................................
cleaning the grease filter in a
dishwasher may cause permanent
discoloration of the filter surface.
Performance of the filter will not be
affected by this discoloration.
[] To remove hold and pull out the
deflector and the grease filter
together,
[]
After cleaning, the filter can be
placed on a towel to air dry.
[]
While the filter is removed, clean any
dirt or grease from the filter casing to
prevent the risk of fire.
[] Pull the grease filter downwards and
out. Support the grease filter so that it
does not fall onto the cooktop.
[] Turn the hood off.
13
Cleaning
and care
hserting
charcoal
/ replacing
fi_ters
the active
For recirculation mode an active
charcoal filter must be used in addition
to the grease filter. The charcoal filter is
designed to absorb cooking odors. The
active charcoal filter is inserted above
the grease filter.
j,
S /
[] To insert the grease filter, make sure
that the red plastic guides are at the
front and facing up.
[] Insert the grease filter in the deflector
and push upwards. It should glide
onto the fixing pins.
[] Replace the filter every 6 months or
when it is no longer absorbing
cooking odors.
Replacement active charcoal filters
can be ordered from Miele.
[] Follow the instructions supplied with
the active charcoal filter.
[] Dispose of the charcoal filter with the
household waste.
14
Cleaning
Changing
and care
the might bulbs
[] Reach through the grille opening and
push the light fixture downwards,
_IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIWIIIIII
[] Pu!l the deflector out and remove the
grease filter as described in
"Cleaning and Care - Grease filter",
[] Remove the active charcoal filter if
existenL
[] Turn the bulb counterclockwise
and
pull it out of its socket,
[] Replace the bulb with a new one in
the reverse order and push upwards,
[] Return the grease filter and if existent
the active charcoal filter,
15
After Sales Service
In the event of a fault which you cannot
correct yourself please contact the
Miele Technical Service Department
1-800-999-1360
techserv@mieleusa,com
1-800-565-6435
service@miele,ca
(+65) 6735 119!
infosea@miele,com,sg
When contacting the Technical Service
Department, please quote the model
and serial number of your appliance,
These are shown on the data plate
which is visible when the grease filter is
removed,
16
Installation
Instructions
18
iMPORTANT
Do not install this exhaust hood over
cooktops burning solid fuel.
When installing the hood, make sure
that the following minimum
distance between the top of a Miele
cooking surface and the bottom of
the hood is:
- 18" (45 cm) above electric
cooktops
- 26" (65 cm) above gas cooktops
- 26" (65 cm) above an open grill
For non-Miele cooking appliances
maintain the safety distances
recommended by the cooktop
manufacturer in their instructions.
SAFETY
iNSTRUCTiONS
If there is any doubt concerning
installation, contact the Technical
Service DepartmenL
1-800-999-1360
techserv@mieleusa.com
1-800-565-6435
service@miele.ca
(+65) 6735 1191
infosea@miele.com.sg
z_During the installation process,
please be careful of sharp edges
!!
Obey local building codes.
If there is more than one appliance
beneath the hood and they have
different minimum safety distances
always select the greater distance.
See "Important Safety Instructions"
for further information.
19
Electrical
data
Important
The hood comes equipped with a 5 ft
(1,5 m) power cord with a NEMA 5-15
molded plug for connection to a
120 VAC, 60 Hz, 15 A power outlet,
Maximum load ...............
Light .....................
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or call Technical
Service,
1-s00-999-1s60
1-800-565-6435
(+65)6735 1191
WARNING:
THIS APPLIANCE
GROUNDED
2O
MUST BE
2 x 50 W
Voltage .....................
120 V
Frequency
60 Hz
..................
Circuit rating ..................
Verify that the voltage, load and circuit
rating information found on the data
plate (located behind the grease filter),
match the household electrical supply
before installing the hood,
450 W
15 A
Appliance
dimensions
DA 3160
1
13
(_bo
1
21
Appliance
dimensions
DA 3180
0 6 II
(150 ram)
11
(a
dai185_s
kt
* The hood can also be installed in a 23 5/s" (60 cm) cabinet,
22
Appliance
dimensions
DA 3190
11
h)
da_18_u_
* The hood can also be installed in a 23 5/s" (60 cm) cabinet,
23
JnstaJJation
installation
accessories
@
24
installation
,7 2 hose clips
to secure the vent ducting to the vent
connection,
,9 2 runners
(! x right, lx left) to support the hood
in the cabinet,
_ t spacer strip
to conceal the gap between the rear
of the appliance and the wall,
(_ Installation kit for recircuJation
mode
contains air outlet grille and hose (not
supplied with the hood, optional
accessory)
_ Installation kit DML 300 to install a
custom paneJ
contains retractable brackets and
screws (not supplied with the hood,
optional accessory)
8 screws 3.5 × 16 mm
to anchor the ventilation hood in the
cabinet,
8 screws M4 × 12 mm
to anchor the ventilation hood at the
runners,
4 screws could be used (alternatively to
the plastic rivet) to fix the spacer bar.
2 screws 4 × 30 mm
to anchor the ventilation hood at rear
wall,
4 plastic rivets
to connect the space bar with the
appliance rear wall,
25
JnstaJJation
D_
26
installation
1. mnstaHing the space
bar
T = K cabinet depth minus G hood
depth
[] The hood depth G depends on the
custom panel:
-
'/_ Hood installed with a cabinet
matching custom panel
-
,'3 Hood installed without front panel
These measures are only valid for the
installation if the front panel sits flush
with the cabinet corpus (without the
door),
i!
3.5 x 16 mm
[] Screw the space bar flush with the
wall under the cabinet side walls,
Jf the front panel should be installed
recessed or flush with the cabinet door,
adjust the measure T accordingly,
[] Cut the supplied space bar to
measure 1".
Clip it with a knife at the predetermined breaking point of the next
lower measure,
[] At the front edge of the spacer strip
draw a vertical line on left and right
side of the inside cabinet,
27
installation
2. Runners
3. Installing
cabinet
the hood
in the
[] Lay the hood on its back side.
Do
.............................................................................
not remove the_"
.............................................
installation
'
protector between the deflector and i::
casing before the installation is
3,5 x 16 mm
The runners are made for side walls of
5/8" (16 ram) and 3/4" (!9 ram). Screw
on the angled side which has the
imprint of the respective cabinet wall
measure.
[] Align the runners with the drawn line
and be sure that they are flush with
the lower edge of the cabinet side
wall. Screw the runners on the left
and right side in the cabinet.
28
[] Hold the grease filter and pull it out
along with the deflector.
installation
........ ...........
[] Take the grease filter out and put it
aside.
[] Push the deflector back in.
[] Insert the hood into the cabinet from
below and until the spring clips click
into place.
[] When installing a 35 7/16" (90 cm)
hood into a 23 5/_,,(60 cm) cabinet,
unscrew the deflector spring clips
while the deflector is pulled ouL
29
installation
4. Secure
the appliance
[] Push the hood back so it sits flush
with the front of the spacer strip,
2x _
4 x 30 mm
[] Pull the deflector out,
[] Drill respective holes and screw the
fixing brackets to the wall or the
cabinet rear wall
[] Screw the hood, with 4 screws, onto
the runners,
[] Tighten the screws to the casing,
[] Remove the installation protection
between the deflector and casing,
[] Connect the space bar from the rear
with 4 plastic rivets at the hood rear
side,
[] Loosen the screws of the fixing
brackets on the hood top,
[] Push the bracket flush to the wall or
the cabinet back wall,
3O
installation
6. install
the grease
filter
[] Remove the protective film from the
grease filter frame.
[] To reinsert the grease filter, pull the
deflector ouL
The installation kit DML 300 is
necessary. It can be obtained as an
optional accessory from Miele. The
installation kit has an installation manual
supplied.
[] Make sure that the red plastic
guides are at the front and facing up.
[] Insert the grease filter into the
deflector, and push upwards. It
should glide onto the fixing pins.
[] The deflector can be adjusted up to
2" (50 mm) towards the front with the
two adiusting screws left and right in
the deflector. Adiust the deflector
until it is flush with the front of the
adiacent cabinetry.
31
installation
7. Venting
Air extraction
mode
[] Complete the venting installation, see
"Air extraction",
Flecirculation
mode
If the hood cannot be installed for air
extraction the appliance must be
connected for recirculation mode,
For recirculation mode a respective
installation kit is recommended which
can be obtained from Miele,
In addition an active charcoal filter is
needed,
[] Insert the hose from below into the air
outlet grille,
[] Insert the hose from the top though
the opening in the cabinet,
o,!
[] The non-return flap is not needed for
the recirculation mode, Pull the
non-return flap off the bracket from
the vent connection,
[] Secure the ventilation hose on the
vent connection of the hood using a
hose clip,
The non-return flap is not used in
recirculafion mode,
[] Screw the air outlet grille onto the
cabinet top,
Make sure that the slats in the grill
point towards the center of the room
and not towards a wall or the ceiling,
[] Install the Active Charcoal Filter (see
"Cleaning and care"),
8. Emectrical connection
Instructions" before connecting to
i connection" and "Important Safety
the mains.
[] Plug in the power cord,
32
Air extraction
WARNING
_iiiii
_iIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
Danger of toxic fumes.
Gas cooking appliances release
carbon monoxide that can be
harmful or fatal if inhaled. The
exhaust gases extracted by the
hood should be vented outside of
the building _.
Do not terminate
the exhaust
ducts in attics, garages,
crawlspaces, etc.
Please read and follow the "Important
Safety Instructions"
to reduce the risk
of personal injury, and follow all local
building codes when installing the
hood.
Exhaust ducting
-
-
and connections
The ducting should be as short and
straight as possible, and the number
of sharp bends should be minimized.
For most efficient air extraction, the
diameter of the ductwork should not
To reduce the risk of fire, onty use
metat ductwork.
CAUTION
To reduce the risk of fire and to
properly exhaust air, be sure to duct
air outside =Do not vent exhaust air
into spaces within walls or ceilings
or into attics, crawl spaces, or
garages.
-
Use smooth or flexible pipes made
from approved non-flammable
materials for exhaust ducting.
- Where the ductwork is horizontal, it
must slope away from the hood at
least 1/,,
J8 per foot (!cm per meter) to
prevent condensation dripping into
the appliance.
-
If the exhaust is ducted through an
outside wall, a Miele Telescopic Wall
Vent can be used.
be less than 6" (150 mm). Use of flat
ducts also reduces the air extraction
efficiency.
-
Noise levels of the hood will increase
if flat ducts or round ducts of less
than 6" (150 mm) in diameter are
used.
33
Air extraction
important
If the ductwork runs through rooms,
ceilings, garages, etc. where
temperature variations exist, it may
need to be insulated to reduce
condensation.
Condensate
trap
In some cases, a condensate trap may
also be required to collect and
evaporate any condensate which may
OCCUK
-
If the exhaust is ducted into an
inactive flue, the air must be expelled
parallel to the flow direction of the
flue.
_iii
olso
(5 7/8,,)
r_r_
o125 mrn
iiiiiiiiiiiiiiiiiisiiiiiiiiiiiiiiiiiiiiiiiiiii_
Never connect an exhaust hood to
an active chimney, dryer vent, flue,
or room venting ductwork. Seek
professional advice before
connecting an exhaust hood vent to
an existing, inactive chimney or vent
flue.
[] When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust outleL
34
Caring
Disposam of packing
rnateria_
Disposa_
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
ii!i!
To prevent suffocation of children,
i ensure that any plastic wrappings,
ii bags, etc. are disposed of safely
and kept out of their reach.
for the environment
of an o_d appliance
Old appliances may contain
that can be recycled. Please
your local recycling authority
possibility of recycling these
materials
contact
about the
materials.
_i/iiiii
iiiiiiiiiiiiiiiiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_
i Before discarding an old hood,
ii unplug it from the outlet and cut off
its power cord to prevent hazards.
:!
35
USA:
Miele, inc.
9 Independence
Way
Princeton, NJ 08540
Phone: 800-843W231
609°419°9898
Fax:
609-419m4298
Technical Service: 800-999m1360
www.miele.com
Canada:
Miele Limited
55G East Beaver Creek Road
Richmond Hill, ON L4B tE5
Phone: 800=643=5381
905-707=1 t71
Fax:
905-707-0177
www.miele.ca
info@miele.ca
(general enquiries)
professional@miele.ca
(commercial
enquiries)
Singapore:
Miele Southeast Asia
Miele Pte. Ltd,
163 Penang Road
# 04 - 02/03 Winsland House II
Singapore 238463
Tel : +65=67351191
Fax: +65-67351161
Email: infosea@miele,com,sg
Internet: www.miele.sg
Alteration rights reserved / 380,_}
M,oNr, 06 ,_,93190 / 01