Car alarm Clifford Matrix 1X (3305X) two way

PHONES
(044) 360-7-130
(050) 336-0-130
(063) 788-0-130
(067) 233-0-130
(068) 282-0-130
Internet store of
autogoods
ICQ
294-0-130
597-0-130
SKYPE
km-130
CAR RECEIVERS — Receivers • Media receivers and stations • Native receivers • CD/DVD changers • FM-modulators/USB adapters • Flash memory • Facia plates and adapters • Antennas • Accessories |
CAR AUDIO — Car audio speakers • Amplifiers • Subwoofers • Processors • Crossovers • Headphones • Accessories | TRIP COMPUTERS — Universal computers • Model computers • Accessories |
GPS NAVIGATORS — Portable GPS • Built-in GPS • GPS modules • GPS trackers • Antennas for GPS navigators • Accessories | VIDEO — DVR • TV sets and monitors • Car TV tuners • Cameras • Videomodules
• Transcoders • Car TV antennas • Accessories | SECURITY SYSTEMS — Car alarms • Bike alarms • Mechanical blockers • Immobilizers • Sensors • Accessories | OPTIC AND LIGHT — Xenon • Bixenon • Lamps
• LED • Stroboscopes • Optic and Headlights • Washers • Light, rain sensors • Accessories | PARKTRONICS AND MIRRORS — Rear parktronics • Front parktronics • Combined parktronics • Rear-view mirrors
• Accessories | HEATING AND COOLING — Seat heaters • Mirrors heaters • Screen-wipers heaters • Engine heaters • Auto-refrigerators • Air conditioning units • Accessories | TUNING — Vibro-isolation
• Noise-isolation • Tint films • Accessories | ACCESSORIES — Radar-detectors • Handsfree, Bluetooth • Windowlifters • Compressors • Beeps, loudspeakers • Measuring instruments • Cleaners • Carsits
• Miscellaneous | MOUNTING — Installation kits • Upholstery • Grilles • Tubes • Cable and wire • Tools • Miscellaneous | POWER — Batteries • Converters • Start-charging equipment • Capacitors
• Accessories | MARINE AUDIO AND ELECTRONICS — Marine receivers • Marine audio speakers • Marine subwoofers • Marine amplifiers • Accessories | CAR CARE PRODUCTS — Additives • Washer fluid •
Care accessories • Car polish • Flavors • Adhesives and sealants | LIQUID AND OIL — Motor oil • Transmission oil • Brake fluid • Antifreeze • Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in
Kyiv and other cities, delivery by ground and postal services. Our experienced
consultants will provide you with exhaustive information and help you to chose
the very particular thing. We are waiting for you at the address
http://130.com.ua
Matrix1X
13
0.
co
m
.u
a
➤Owner’s Guide
Autogood products «130»
Limited lifetime consumer warranty
13
0.
co
m
.u
a
Directed Electronics ("Directed") promises to the original purchaser to repair or replace
with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized
Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy
of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone
number and address; complete product description, including accessories; the year, make
and model of the vehicle; vehicle license number and vehicle identification number. All
components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date
of purchase of the same. This warranty is non-transferable and is automatically void if: the
original purchaser has not completed the warranty card and mailed it within ten (10) days
of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use,
neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage. TO
THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY,
ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY,
OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY
AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS
UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT
OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND
HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR
VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR
MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY
i
© 2008 directed electronics
Autogood products «130»
m
.u
a
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE
AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.
DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have
other rights that vary from State to State.
0.
co
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your authorized Directed dealer for details of the plan or call Directed Customer Service at 1-800876-0800. Directed security systems, including this unit, are deterrents against possible
theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft
of the automobile, its parts or contents; and hereby expressly disclaims any liability whatsoever, including without limitation, liability for theft, damage and/or vandalism.
Directed does not and has not authorized any person or entity to create for it any other
obligation, promise, duty or obligation in connection with this security system.
13
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤
➤
➤
➤
➤
➤
➤
➤
➤
Date of purchase
Your full name and address
Authorized dealer's company name and address
Type of alarm installed
Year, make, model and color of the automobile
Automobile license number
Vehicle identification number
All security options installed on automobile
Installation receipts
ii
© 2008 directed electronics
Autogood products «130»
Table of contents
13
0.
co
m
.u
a
Limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
2-way LCD remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
LCD screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Standard remote configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
What is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
System maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FCC/ID notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Replacement remote controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2-way LCD remote control functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Standard configurations (1-way and 2-way remote controls). . . . . . . . . . . . . . . . 7
Standard LCD icon configurations (2-way only). . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
System signal paging features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Out of range notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programming LCD remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To enter programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Beeps/Vibration On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Illumination On/Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Page notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To exit programming mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Active arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Passive arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Disarming without a transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Dome light control (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Silent mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
False Alarm Control Technology (FACTIITM) . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Auxiliary outputs (options) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Interpreting zone diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
iii
© 2008 directed electronics
Autogood products «130»
13
0.
co
m
.u
a
Owner recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Vehicle recovery system (VRS®) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Arming the VRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Triggered sequence, VRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Disarming the VRS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Quick reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
iv
© 2008 directed electronics
Autogood products «130»
2-way LCD remote control
3
7
co
m
.u
a
5
RPN 7341V/P/X
1
1-800-274-0200
4
2(66) CODES
FCC ID:EZSDEI489
2
6
Auxiliary Channel Button
2.
Arm Button
3.
LCD Screen (see LCD Screen)
4.
Disarm Button
Panic Button
13
5.
0.
1.
6.
Battery Compartment
7.
Program Button
1
© 2008 directed electronics
Autogood products «130»
LCD screen
1
2
3
4
5
6
7
17
16
15
8
13
9
a
14
m
.u
12
10
0.
1. Transmit
co
11
10. Battery level indicator
11. Remote sending
3. Receive
12. Vibrate mode
13
2. Out of range
4. Aux Output 2 or 3
13. Ignition
5. Garage door (519H2 option)
14. Vehicle number
6. Warn Away®
15. Door
7. Alarm
16. Arm
8. Trunk or Hood
17. Disarm
9.
Sensor
2
© 2008 directed electronics
Autogood products «130»
Standard remote configuration
controls the Lock–Arm/Panic On/Panic Off function.
a
controls the Unlock–Disarm/Panic Off function.
0.
seconds).
controls the Panic On/Off function (hold for 2-
co
or
m
.u
controls Silent Mode™ and an Auxiliary Output (2).
pressed together control an Auxiliary Output (3).
13
and
P
(located on back of the remote) selects the vehicle to control
and also provides user selection of LCD remote response .
3
© 2008 directed electronics
Autogood products «130»
What is included
➤
➤
Control module
1 four-button 2-way LCD transmitter
➤
1 four-button transmitter
note: On both remotes the panic button is the same color.
➤
➤
➤
0.
➤
a
➤
m
.u
➤
Wire harnesses
The 514N six-tone programmable siren
In-vehicle status LED indicator light
A push-button Valet switch
Your warranty registration
Failsafe® Starter Kill ready circuitry
(may require additional labor)
548T receiver/antenna
co
➤
13
Important information
Congratulations on the purchase of your state-of-the-art vehicle
security system. This system has been designed to provide years
of trouble-free operation. Due to the complexity of this system,
it must be installed by an authorized dealer only. Installation of
this product by anyone other than an authorized dealer voids the
warranty. All dealers are provided with preprinted dealer certificates to verify that they are authorized.
This owner’s guide should help you to get the most out of your
system. Please take the time to read it prior to using the system.
4
© 2008 directed electronics
Autogood products «130»
➜ System maintenance
This system needs no specific maintenance beyond remote
control battery replacement. The 2-way remote is powered by a
1.5V AAA battery. The 1-way remote is powered by a pair of 3V,
CR2016 batteries.
Battery Level Indicator (2-way remote)
The Battery Level indicator has four level indicators that serve as
a visual indication of battery charge. When the battery reaches a
a
low charge level that requires replacement, the remote control
m
.u
will generate a single notification chirp, and the Battery Level
co
indicator will flash continuously.
0.
Battery Replacement (2-way remote)
Gently pull the end of the battery door away from the top of the
13
remote control then slide the door up to expose the battery and
remove the expired battery. Place the new battery into the remote
control observing the correct polarity. When power is returned
the remote control will display all icons in the LCD and generate
all beeper tones once. Press any button on the remote to terminate the beeper tone review.
➜ Your warranty
Your warranty registration must be returned and the bar code
serial number must not be removed. If the warranty registration
is not returned, you do not have a warranty. It is also necessary to
5
© 2008 directed electronics
Autogood products «130»
keep your proof of purchase, which reflects that the product was
installed by an authorized dealer. Make sure that you receive the
warranty registration from your dealer.
➜ FCC/ID notice
m
.u
a
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesirable operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
13
0.
co
operate this device.
6
© 2008 directed electronics
Autogood products «130»
Replacement remote controls
You can purchase replacement remote controls from your
Authorized Dealer or on-line at the following web site:
www.directedstore.com
Once you receive your new remote control, please refer to
a
instructions included on the remote packaging.
m
.u
2-way LCD remote control functions
The LCD remote control buttons are used to send commands to
co
the system. The descriptions below reflect the standard configuration for this system. The buttons can be custom configured for
0.
the user’s specific needs by the installer. Also, the user can
configure the LCD remote for certain responses (see
13
Programming LCD Remote section).
➜ Standard configurations (1-way and 2-way remote
controls)
Button
The arming function is controlled by pressing this button for
one second.
Button
The disarming function is controlled by pressing this button for
one second.
7
© 2008 directed electronics
Autogood products «130»
Button
Silent Mode™ and an optional auxiliary function are controlled
by pressing this button. (Silent Mode™ works by pressing this
button for less than one second before arming or disarming. An
optional auxiliary function, such as trunk release, can be
controlled by pressing this button for 1.5 seconds.)
The auxiliary output controls __________________________.
or
Button
and
m
.u
a
The panic feature is controlled by pressing this button for
approximately two seconds.
Buttons
An optional auxiliary convenience or expansion function that
co
you have added to your system can be activated by pressing these
0.
buttons simultaneously.
The auxiliary output controls_________________________.
13
Program Button (on
rear of 2-way LCD remote only)
Use this button to select the vehicle to control from the remote.
Also use this button to configure response characteristics from
the LCD remote (see Programming 2-Way Remote).
8
© 2008 directed electronics
Autogood products «130»
➜ Standard LCD icon configurations (2-way only)
Icon
The transmit icon will be displayed while the remote control is
transmitting a command to the vehicle.
Icon
The signal icon will be displayed if a command is transmitted to
the vehicle but the command page is not received.
a
Icon
The receive icon will be displayed while the remote control is
m
.u
receiving a page from the vehicle.
Icon
co
The auxiliary and sensor icons will display which auxiliary is operating, or which security sensor (zone 2,4 or 7) is in Warn Away®
0.
or alarm state.
Icon
13
The garage door icon—for use with optional 519H2.
and
Icons
The above Warn Away® displays when a security feature has been
tripped, but not to full alarm.
and
Icons
The above icons will display when a security feature has been
tripped to a full alarm condition.
9
© 2008 directed electronics
Autogood products «130»
Icon
The trunk icon will display for full alarm by flashing for a few
seconds and then display continuously until the page is cleared.
Icon
The shock sensor icon will display for both Warn Away® and full
alarm by flashing for a few seconds and then display continuously until the page is cleared.
a
Icon
m
.u
The battery icon always displays the current charge capacity
remaining in the remote’s battery.
Icon
co
The vibrate icon will always display if the remote is programmed
for vibrator notification (see programming LCD remote section
0.
of the guide).
13
Icon
The ignition icon will display for full alarm by flashing for a few
seconds and then display continuously until page is cleared.
Icon
The vehicle icon always displays the current vehicle (maximum
of 4 vehicles) being controlled by the remote. If a Warn Away®
or alarm trigger should occur at one of the other vehicles, that
vehicle’s number will be displayed and the LCD will display that
vehicle’s status. To change back to the original vehicle selected,
10
© 2008 directed electronics
Autogood products «130»
press and release the program button until the vehicle number is
shown.
For example, If the remote was originally on vehicle number 1 and
a trigger page was received for vehicle number 2, the remote will
show the trigger alarm and show number 2 on the display. After
clearing the page, press and release the program button until number
1 is displayed. Now you can operate the alarm system on vehicle
number 1.
a
Icon
m
.u
The door icon will display for full alarm by flashing for a few
seconds and then display continuously until the page is cleared.
Icon
co
The arm icon will flash when the system is locking the doors and
0.
display continuously until the system is armed.
Icon
13
The disarm icon will flash when the system is unlocking the
doors and display continuously until the system is disarmed.
11
© 2008 directed electronics
Autogood products «130»
Transmitter functions
m
.u
Remote operation
a
This system uses a computer-based learn routine to learn the
transmitter buttons. This makes it possible to assign any transmitter button to any system function. The transmitter initially
comes programmed with Standard Configuration, but may also
be customized by an authorized dealer. The buttons described in
this manual correspond to a Standard Configuration transmitter.
The system operates at 434 MHz and incorporates Directed’s proprietary out-board technology transceiver. The high frequency combined
co
with Binary Data communication achieves superior range with twoway communication.
0.
➜ System signal paging features
13
A page is the signal the control module sends to the remote control
as confirmation of receipt of a command or alarm system status.
When the remote control receives a page it will generate a page
notification to the user (notifications are audible beeps and-or
vibration) and the LCD Icons will display the current system status.
Command Page
When a command (arm/disarm, or auxiliary channel) from the
remote control is sent and received, the system will send a
command page back to confirm receipt.
12
© 2008 directed electronics
Autogood products «130»
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will be
sent to the remote control. When the remote receives an Alarm
Page, the LCD icons will display the alarm system status information and the remote control will generate beeps and-or vibration.
An Alarm Page alert is a series of 5 groups of 4 rapid beeps
(shock, trunk, door, ignition, or hood trigger) and the LCD icon
that caused the alarm will display. The remote will beep and or
a
vibrate every 60 seconds to alert the user that the alarm system
m
.u
was triggered and will continue until the alarm page is cleared.
Page Recognition (Acknowledgement)
To clear a page alert/notification, quickly press any button on
co
the remote control. This can be performed at any time during or
after the page notification has occurred.
0.
The remote control will not send a command to the system at
13
this time; it will only clear future repeats of the page notification.
The next time a button is pressed on the remote control it will
send a command to the system.
➜ Out of range notification
If a command is issued from the remote, but the remote is set to
the incorrect vehicle or is beyond the range of the vehicle to
receive the command, the remote responds with 3 set of 2 quick
beeps and the
icon will flash 3-times.
13
© 2008 directed electronics
Autogood products «130»
Programming LCD remote
➜ To enter programming mode
Press and hold the
P
button until one long beep is heard.
Programming mode to customize the remote’s response is now
entered.
m
.u
➜ Beeps/Vibration On/Off
a
note: If no buttons are pressed within 5-seconds, programming mode will exit with 2-beeps.
Press
to select beeps/vibration On/Off. Beeps alone, vibra-
tion alone, beeps and vibration, or no beeps and vibration can be
Programming response Icon display*
0.
Beep/Vibrate settings
co
selected. Refer to the table below for these settings.
1-beep
Siren icon On
Vibrate only
1-vibrate
Vibrate icon On
Beep & Vibrate
1-beep and 1-vibrate
13
Beeps only (default)
No Beep and No Vibrate 1 long beep
Vibrate and siren icon
On
Vibrate and siren
icons Off
*Note: This is icon display during programming.
14
© 2008 directed electronics
Autogood products «130»
➜ Illumination On/Off
Press
to select LCD backlight illumination On/Off. The
LCD backlight will illuminate when a remote button is pressed,
or an alarm status page is received.
LCD Backlight settings Programming response
1-beep, backlight ON
OFF
2-beeps, backlight OFF
➜ Page notification
m
.u
a
ON
co
The remote control can be programmed to notify the user of a
page (audibly beeping if the vehicle’s status changes, e.g. door
0.
unlocked, engine started, vehicle violation, etc.). On the LCD
remote press
to select page On/Off. One beep is page On,
13
Two beeps is page Off. When programmed off the remote will not
give any notification that a page was received from the vehicle.
Note: If programmed Off, no alarms will be notified to the
remote. Command information (armed/disarmed) will be notified to the remote.
➜ To exit programming mode
The LCD remote control will exit programming mode after 5seconds of inactivity and will emit 2 long beep.
15
© 2008 directed electronics
Autogood products «130»
Using your system
The buttons described in this manual correspond to the standard
configuration. Remember, this is not the only way your transmitter may be set up. It can be custom configured to meet your
needs. See your installer for additional details.
➜ Active arming
of your remote for one
a
You can arm the system by pressing
second. When the system arms, from the vehicle you will hear a
m
.u
short siren sound, or chirp, and see the parking lights flash once.
If the power door locks are controlled by the system, the doors
will also lock. While the system is armed, the in-vehicle’s status
co
LED will flash approximately once per second, indicating that
the system is actively protecting your vehicle. If you hear a
0.
second chirp after arming and note that the in-vehicle’s status
LED is flashing in groups, see the Diagnostics Section of this
13
guide. This extra chirp is called Bypass Notification.
The LCD remote responds to active arming with one beep and
the
icon will flash 5-times to indicate successful arming of
the system.
If the LCD remote beeps twice after arming, the system has detected
an active sensor that should be checked. For example, a door open
icon will be displayed flashing 5-times on the LCD screen.
16
© 2008 directed electronics
Autogood products «130»
Passive arming
The system can be programmed to arm itself automatically (called
passive arming). If the system is programmed for passive arming, it
will automatically arm 30 seconds after the ignition is turned off
and the system detects that you have left the vehicle by opening and
closing a door. Whenever the system is in its 30-second passive
arming countdown, the in-vehicle status LED will flash twice as
fast as it does when the system is armed. At the 20-second point of
the countdown, the siren will chirp to indicate that the system is
m
.u
to indicate that the system is armed.
a
about to arm. At the 30-second point, the parking lights will flash
The LCD remote responds to passive arming with one beep and
icon will flash 3times to indicate successful arming of
the system.
co
the
13
0.
note: If any protected entry point (such as a door or a
switch-protected trunk or hood) is open, the system will
not passively arm (unless forced passive arming is programmed on. See Programming Options section.) Additionally, if a door, hood or trunk is triggered during the
arming countdown, the 30-second countdown starts over.
When armed your vehicle is protected as follows:
➤
➤
➤
Light impacts trigger the Warn Away® signal. When triggered,
the siren chirps and the parking lights flash for a few seconds.
Heavy impacts trip a Triggered Sequence. The sequence
consists of the siren sounding continuously and the parking
lights flashing for a pre-programmed period, which can
range in duration from 1 to 180 seconds.
If a door is opened, the system will immediately start
17
© 2008 directed electronics
Autogood products «130»
➤
m
.u
➤
a
➤
chirping the siren and flashing the parking lights. Three
seconds later, the siren output changes to a continuous blast.
This progressive response gives you time to disarm the system with your LCD remote if you inadvertently open the
door while the system is armed, while still providing instant
response (even if the door is immediately closed).
Turning on the ignition key will trip the same progressive response as opening a door.
The optional starter kill prevents the vehicle’s starter from
cranking.
Any full trigger of the alarm system will immediately send an
alarm page to your remote informing you that your vehicle
should be checked.
co
➜ Multi-level security arming
Multi-Level Security Arming allows you to select which of the
0.
security system's inputs or sensors will be active and which will
be bypassed at the time that the system is armed. (See the Table
13
of Zones section of this guide.) Pressing
again within five
seconds of arming the security system will activate the MultiLevel Security Arming feature. Each time
is pressed again, a
different security level is selected. The different security levels
can be selected as follows:
➤
Press
once: The siren chirps once. The system is armed.
➤
Press
a second time within five seconds: The siren
chirps twice followed by a long chirp. Zone 2 is now
bypassed.
18
© 2008 directed electronics
Autogood products «130»
➤
Press
a third time witihin 5 seconds, the siren chirps 3
times then followed by a long chirp. Zone 4 is now bypassed.
➤
Press
a fourth time within five seconds: The siren cirps
four times follwed by a long chirp. Zone 2 and 4 are now
bypassed.
➤
Press
a fifth time within five seconds: The siren chirps
five times followed by a long chirp. All input zones, except the
ignition are now bypassed.
Hold down the
to begin the Multi-Level-Security Arming
a
➤
m
.u
cycle over again.
co
note: Multi-Level Security Arming only applies to a single arming cycle. Once the system is disarmed and then
re-armed, all the zones will be active again.
After each press of the
to reach the next level of security, the
of the
0.
remote will emit normal arm notification (1 beep and 5 flashes
icon). For easiest operation in reaching each level of
13
security, press
immediately after each notification.
➜ Disarming
To disarm the system, press
. You will hear two chirps, and
the parking lights will flash twice. If the power locks are
connected to the system, the doors will unlock. If the siren chirps
either four or five times when disarming, refer to the Diagnostics
section of this guide. This is called Tamper Alert.
19
© 2008 directed electronics
Autogood products «130»
The remote will indicate disarm notification with 2 beeps and 5
flashes of the
icon. If disarming after the system has been
triggered, the remote control will send a diagnostic notification
as a reminder. These diagnostic notifications are:
1. If a sensor triggered the system, the remote will emit 4 quick
beeps and the LCD screen will indicate which sensor (5flashes) tripped the alarm.
2. If a switch (Zone 1, 3, or 5) triggered the system, the remote
a
will emit 4 quick beeps and the LCD screen will indicate
m
.u
which switch (5 flashes) tripped the alarm.
3. If the system was triggered so many times that FACTII is
active the remote will emit the above notifications with 5
13
0.
co
beeps instead of 4.
20
© 2008 directed electronics
Autogood products «130»
➜ Disarming without a transmitter
This feature allows you to disarm the security system without the
remote transmitter should it be lost, damaged, or disabled. In order
to disarm the system without a remote transmitter, you must have
the vehicle’s ignition key and know where the Valet button is
located. Be sure to check with the installer for the location and the
number of presses of the Valet button required to disarm the system.
To disarm the security system,
a
turn the ignition to the ON posi-
m
.u
tion. Press the Valet button the
preset number of times (one to
DRW-35
five times) within 15 seconds. After five seconds the system will
co
disarm. If the system does not disarm, you may have waited too long;
turn the ignition off and on and try again.
0.
Location of Valet Button_________________________________
13
Number of Pulses______________________________________
important! The unit can be programmed to respond to
one to five pulses of the Valet button for the disarm function. Be sure to check with the installer for the desired
programming.
The LCD remote will indicate disarm notification with 4 quick
beeps and 5 flashes of the
and triggered zone icons.
21
© 2008 directed electronics
Autogood products «130»
➜ Dome light control (optional)
security only
The dome light activates for 30 seconds after the system is
disarmed.
Ignition controlled
The dome light activates for 30 seconds after the ignition is
turned Off.
a
door controlled
The dome light activates for 30 seconds after the system sees a
m
.u
door has closed. (If door was held open for longer than 3
minutes the dome light will not illuminate.)
co
full
The dome light activates for 30 seconds after seeing door closure,
0.
ignition, or security disarm. (This is the factory setting.)
13
➜ Silent mode
To temporarily turn off the arm or disarm chirps, use Silent
Mode™. Press
for less than one second before arming or
disarming, and the confirmation chirp(s) will be eliminated for
that one operation only. If you want the arm/disarm chirps
turned off permanently, your dealer can do this for you.
note: The Warn Away® response to lighter impacts is
bypassed if the system is armed using Silent Mode. This
ensures that no chirps will be emitted by the siren in an
area you want chirp-free. The system is still fully capable
of triggering. Only the Warn Away® response is bypassed.
22
© 2008 directed electronics
Autogood products «130»
The LCD remote responds with the normal arm/disarm notifications in silent mode. (If the remote has beeps programmed
On, the remote will beep.)
➜ Panic mode
note: On both remotes the panic button is the same color.
a
LCD remote
m
.u
If you are threatened in or near your vehicle, you can attract
attention by triggering the system with your LCD remote. Just
press
or
button for approximately two seconds, and
co
you will enter Panic Mode. The siren will sound and the parking
lights will flash for the programmed siren duration. To stop
or
button on the LCD
0.
Panic Mode at any time, press
remote again.
13
The LCD remote responds with one beep and display of the
icon upon entering Panic Mode.
4-button remote
If you are threatened in or near your vehicle, you can attract
attention by triggering the system with your transmitter. Just
press
or
for approximately two seconds, and you will
enter Panic Mode. The siren will sound and the parking lights
will flash for the programmed siren duration. To stop Panic Mode
at any time, press
, or
on the remote transmitter again.
23
© 2008 directed electronics
Autogood products «130»
➜ Valet mode
You can prevent your security system from automatically arming
and triggering by using Valet Mode. This is very useful when
washing the vehicle or having it serviced. In Valet Mode, the
security system will not arm, even with the remote transmitter,
but all convenience functions (door locks, trunk release, etc.)
will continue to work normally.
To enter or exit Valet Mode:
a
1. Turn the ignition on.
m
.u
2. Turn the ignition off.
3. Press and release the Valet
DRW-35
button within 10 seconds.
co
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.
0.
The remote will respond with 5 flashes of the
icon and 2
13
beeps on entering or exiting Valet® Mode.
To enter or exit Valet Mode using the transmitter:
1. Open any vehicle door.
Quickly press the following buttons in the sequence indicated.
2. Press
.
3. Press
.
4. Press
again.
The in-vehicle status LED will light solidly if you are entering
Valet® Mode, and it will go out if you are exiting Valet® Mode.
24
© 2008 directed electronics
Autogood products «130»
➜ False Alarm Control Technology (FACTII)
Your system offers FACT II, a feature that prevents annoying
repetitive trigger sequences due to a faulty sensor or environmental conditions such as thunder, jackhammers, airport noise,
etc.
Here’s how it works: The alarm triggers three times. Each time,
the same sensor is triggering the alarm. The three triggers are
within 60 minutes of each other. FACT II will interpret this
a
pattern of triggers as false alarms. After the third trigger, FACT
m
.u
II ignores, or bypasses that sensor (along with any other sensors
sharing the same zone) for 60 minutes.
If the bypassed sensor tries to trigger the system while it is being-
co
bypassed, the 60-minute bypass period will start over. This
ensures that a sensor that continually triggers will remain
0.
bypassed.
13
Doors are covered by FACT II differently: If the alarm is triggered by an open door for three full cycles, the doors will be
bypassed until the trigger ceases.
FACT II is programmable. See the Programming Options
section of this guide.
25
© 2008 directed electronics
Autogood products «130»
Auxiliary outputs (options)
This system also supplies outputs that can control convenience
options such as remote control trunk release and window automation. Consult your dealer for available options for your system.
Channel 2 Trunk release: When connected, pressing
for 1.5
seconds will remotely release the vehicle trunk lid.
Channel 3 auxiliary output: When connected, pressing
and
m
.u
additional convenience option.
a
will immediately activate this output to control an
The remote will respond with a page notification consisting of
one long beep and for 4 seconds displays the channel number on
co
the LCD screen. This occurs at the remote after the system has
13
0.
received the command to activate any of the Auxiliary outputs.
26
© 2008 directed electronics
Autogood products «130»
Diagnostics
The microprocessor at the heart of your security system is
constantly monitoring all of the switches and sensors that are
connected to it. It detects any faulty switches and sensors and
prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred
during your absence. Refer to the System Status Chirps and Table
m
.u
➜ Arming diagnostics
a
of Zones charts for diagnostic information.
If the system is armed while an input is active (door open, sensor
triggering, etc.) the unit will chirp once when arming and then
Notification.
co
one more time a few seconds later. This is called Bypass
13
0.
note: Bypass Notification will not occur when using
Silent Mode™ or if chirps have been programmed OFF.
The security system will ignore the input that was active when
the system was armed, until the input goes away. Three seconds
later the system will monitor that input normally. For example,
if your vehicle has interior light exit delay, and you arm the
system before the interior light goes out, you may hear Bypass
Notification chirps. Once the light shuts off, however, the doors
are monitored normally.
27
© 2008 directed electronics
Autogood products «130»
➜ Disarming diagnostics
Extra disarm chirps are the Tamper Alert. If four chirps are heard
when disarming, the system was triggered in your absence. If five
chirps are heard, a zone was triggered so many times that False
Alarm Control Technology (FACT II) has bypassed that zone (see
FACT II section of this guide). The in-vehicle status LED will indicate which zone was involved. (See Table of Zones section of this
guide.) The system will retain this information in its memory, and
a
continue to chirp four or five times each time it is disarmed, until
m
.u
the next time the ignition key is turned on.
➜ System status chirps
The siren will chirp when arming/disarming the system. The
co
pattern of chirps will audibly report the system’s status as
Number of Chirps
Description
Arm
1
System armed
Arm
1 (3-second delay), 1
System armed with
Bypass Notification
Disarm
2
System disarmed
Disarm
4
System disarmed with
Tamper Alert
Disarm
5
System disarmed FACT II
active
13
Action
0.
described below.
28
© 2008 directed electronics
Autogood products «130»
➜ Table of zones
The zone number is the number of LED flashes used by the
system to identify that input. The standard input assignments
are listed below, along with spaces to write in any optional
sensors or switches you have had installed.
Zone - Number
of LED Flashes
Dealer-Installed
Options
Description
Instant trigger - often used
for trunk pinswitches
2
Shock sensor input - a light
impact activates warn away
and a heavier impact activates
full alarm.
3
Door switch trigger
4
Optional sensor inputs for
warn away and full
alarm notification.
m
.u
co
0.
Ignition trigger
13
5
a
1
29
© 2008 directed electronics
Autogood products «130»
➜ Interpreting zone diagnostics
Warn Away responses are not reported by arming or disarming
diagnostics. If you receive a Bypass notification when arming or
a Tamper Alert notification when disarming, look at the invehicle status LED. Active or triggered zones will be indicated by
a pattern of blinks by this LED.
Example
a
If Zone 3 was active or triggered, the in-vehicle LED will blink
three times with a two-second pause. Then it will blink three
times again, and repeat until the ignition is turned on.
co
m
.u
note: Your system stores the last six triggered zones in
memory. If your system has been triggered but the LED
has been reset by turning on the ignition, your dealer can
still recall the last six zones that were triggered. Contact
your dealer for details.
0.
Code hopping
13
The receiver and transmitters each use mathematical formulas
called algorithms to change their codes each time the transmitter
is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes
should be. This helps to keep the transmitter "in sync" with the
control unit even if you use the remote control out of range of
the vehicle. However, if the transmitter has been pressed many
times out of range of the vehicle, or if the battery has been
removed, it may get out of sync with the control unit and fail to
operate the system. To re-sync the remote control press
30
of
© 2008 directed electronics
Autogood products «130»
the transmitter several times within range of the vehicle. The
alarm will automatically re-sync and respond to the transmitters
normally.
Owner recognition
Owner Recognition is a feature available exclusively from Directed.
Using the Directed Bitwriter®, a hand-held programming tool,
a
your dealer can program many of the system settings. The
m
.u
programmer makes it possible to program different settings for
each transmitter that is used with the system. Then, whenever a
specific transmitter is used, the system will recall the settings
co
assigned to that transmitter. Owner Recognition lets up to four
users of the system have different settings that meet their specific
0.
needs. It is almost like having four separate alarms in your vehicle,
one for each user.
13
note: Owner Recognition cannot be programmed without a Directed Bitwriter® and the necessary software.
Check with your dealer for more information.
31
© 2008 directed electronics
Autogood products «130»
Rapid resume logic
This Directed system will store its current state to non-volatile
memory. If power is lost and then reconnected, the system will
recall the stored state from memory. This means if the unit is in
Valet Mode and the battery is disconnected for any reason, such
as servicing the car, when the battery is reconnected the unit will
still be in Valet Mode. This applies to all states of the system
m
.u
a
including arm, disarm, VRS®, and Valet Mode.
Power saver mode
Your system will automatically enter Power Saver Mode while
co
armed or in Valet® Mode, after a period of time in which no
operation has been performed. This lowers the current draw to
0.
the vehicle’s battery. Power Saver Mode takes over under the
13
following conditions:
➤
Power Saver when the system is armed: After the system has
been armed for 24 hours, the in-vehicle LED will flash at
half its normal rate, decreasing the system's current draw.
➤
Power Saver in Valet® Mode: When the system enters Valet®
Mode the in-vehicle LED illuminates steadily. If the vehicle
is not used (ignition is not turned on) for a period of one
hour while the system is in Valet® Mode, the LED will shut
off. If the system remains in Valet® Mode, the LED will
come back on the next time the ignition is turned on and
then back off.
32
© 2008 directed electronics
Autogood products «130»
Programming
Programming options control what your system does during
normal operation, and require few or no additional parts.
However, some may require additional installation labor.
The following is a list of the program settings, with the factory
settings in Bold:
13
0.
co
➤
a
➤
Active arming (only with the remote) or passive arming (automatic arming 30-seconds after the last door has been
closed).
Arming/disarming confirmation siren chirps on or off.
The ignition controlled door lock feature on or off: With
this feature on, the doors will lock three seconds after the
ignition is turned on, and the doors are closed, and unlock
when the ignition is turned off. The system will not lock the
doors when the ignition is turned on with any door open.
The bitwriter is not needed to program theses separately, it
should be in the programming grid to do these 2 independently. Ignition lock and unlock are independent features
and can be programmed separately.
Passive door locking (with passive arming) or active door
locking (only when arming with the remote). Passive locking
allows the vehicle's doors to lock when the security system
passively arms (after the 30 second countdown). This feature
only works if passive arming has been programmed.
m
.u
➤
➤
33
© 2008 directed electronics
Autogood products «130»
note: When programmed for passive arming and active
lock, if the system is disarmed without a door being
opened, the system will relock the doors when it passively rearms.
➤
Panic mode enabled/disabled with the ignition on: Some
states have laws against siren capability in a moving vehicle.
➤
Forced passive arming on or off: If your system is
programmed for passive arming and the forced passive
arming feature has been programmed on, the system will
a
passively arm after one hour, even if a protected entry has
m
.u
been left open. This feature is useful if a door has been left
ajar when leaving the vehicle. Forced passive arming ensures
that the security system will be armed in every situation.
13
0.
co
note: When the system passively arms after one hour, the
entry point that has been left open, and anything connected to the same zone, is bypassed and cannot trigger
the system. However, the remaining inputs to the system
are fully operational.
➤
Automatic Engine Disable (AED) on or off: The purpose of
this feature is to protect the vehicle from being stolen at all
times, regardless of whether or not the alarm is armed. If
AED is programmed on, the starter of the vehicle will be disabled 30 seconds after the ignition is turned off. Once the
key is turned off, the in-vehicle LED will flash slowly (onehalf its normal armed rate) to indicate the AED arming
cycle. Thirty seconds later, the starter of the vehicle will be
disabled. To start the car, it will be necessary to disarm the
system with the remote. It is also possible to disarm the AED
34
© 2008 directed electronics
Autogood products «130»
feature by turning the ignition key to the RUN position and
pressing the Valet® button the programmed number of
times. AED is disabled when the system is in Valet® Mode.
note: This feature will only function if the Failsafe®
Starter Kill relay has been installed.
➤
Full trigger response 30 or 60 seconds: This determines how
long the full triggered sequence lasts. Some states have laws
regulating how long a security system can sound before it is
a
considered a nuisance. If your installer is programming the
m
.u
security system with the Directed Bitwriter, the full triggered
response can be programmed for any duration ranging from
1 to 180 seconds.
False Alarm Control Technology Off: Please refer to the
co
➤
FACT II section of this manual for a complete explanation of
0.
how FACT II operates. If FACT II is programmed off, the security system will respond to inputs from any sensor indefi-
13
nitely.
note: Because many states have laws regulating security
systems, programming FACT II off may cause your system to violate state laws.
➤
Comfort Closure Off: Windows will close upon locking the
vehicle.
➤
Forced Passive Arming Off: If passive arming is on and a door
is left open the system will be armed after 30-seconds.
35
© 2008 directed electronics
Autogood products «130»
➤
Panic with Ignition Off: Prevents the Panic button on the remotes
from activating panic with ignition On (not allowed in some
states).
➤
Progressive door trigger on or off: When the system is armed
and a door is opened, the system responds with ten chirps
prior to beginning the full triggered sequence. If an instant
trigger is desired, the progressive door trigger can be programmed off.
➤
Valet® pulse count: The number of presses of the Valet®
a
button required to disarm the security system, AED, or the
m
.u
VRS® system can be programmed from one to five presses. The
default setting is one press.
➤
Siren tones and chirp volume: The output of the Revenger®
co
Soft Chirp® siren consists of six different tones in sequence.
Any of these tones can be eliminated by your dealer, result-
0.
ing in a unique, easily identifiable siren sound. The siren
chirps can be either full volume or six decibels quieter than
13
the full alarm blast.
36
© 2008 directed electronics
Autogood products «130»
Installation options
The system has many options that may require extra parts and
labor. Some of the possibilities are listed here.
➤
Progressive unlocking: In most cars with electric power door
locks, the system can be configured so that when the system is
disarmed, only the driver’s door unlocks. A second press of the
button unlocks the other doors.
Vehicle Recovery System (VRS®): VRS is an anti-carjacking
a
➤
m
.u
device designed to help in the safe recovery of your vehicle
in case of a carjacking. Please refer to the Vehicle Recovery
System section of this guide for a complete explanation of
co
how the Vehicle Recovery System operates.
0.
Vehicle recovery system (VRS®)
13
The optional VRS feature is designed to ensure that any unauthorized user of your vehicle (even if using your keys and remote control)
will not be able to permanently separate you from your vehicle.
The VRS cannot prevent a carjacking attempt; however, it does
ensure that if your vehicle is taken by an unauthorized user, it will
be disabled (after several progressive warnings) as safely as
possible. Should a carjacking occur, the VRS allows you to
concern yourself with your personal safety without worrying
about your property.
37
© 2008 directed electronics
Autogood products «130»
Directed has engineered this vehicle security system, the Failsafe®
Starter Kill, and the VRS feature to provide the best combination of personal safety and property protection available. When
properly installed, the system can never inadvertently stop your
vehicle in traffic or on railroad tracks while the vehicle is in operation. It is unlike other systems that shut down your engine
while it is running. This system is designed to perform starter interrupt, or starter kill. The Failsafe® Starter Kill cannot shut
m
.u
from starting in the first place.
a
down an already-running engine – it can only prevent an engine
co
important! Any installation that allows this product to
shut down a vehicle's engine when it is running is contrary to the product’s design and intended usage, and
Directed hereby expressly disclaims any liability resulting
therefrom.
0.
➜ Arming the VRS
13
To arm the VRS, turn the ignition to the ON position and press
the arm button on the remote transmitter for one second. The
parking lights will flash and the siren will chirp once. This can be
done before driving or while driving the vehicle. Once the system
is armed, it will initiate its triggered sequence (see below) if any
door is opened and closed. If you are forced from the vehicle, the
system will trigger as the door is opened and closed. This is how
the system works to combat intersection carjacking. To protect
against parking lot carjacking, arm the VRS before leaving the vehicle. The system will now trigger automatically the next time
you or anyone drives the vehicle. This helps to protect the vehicle
38
© 2008 directed electronics
Autogood products «130»
if someone takes your keys and remote transmitter by force in a
parking lot.
note: If the VRS® system is armed while operating the vehicle and not disarmed prior to leaving the vehicle, it is still
armed and will trigger the next time the vehicle is driven.
➜ Triggered sequence, VRS
Fifteen seconds after the last door has closed, the in-vehicle LED
a
will begin flashing. This delay is intended to allow you time to
m
.u
distance yourself from your vehicle in the event of a carjacking.
Forty-five seconds later, the siren begins chirping and the park-
ing lights begin flashing. This time could be used to notify au-
co
thorities that your vehicle has been hijacked, and tell them what
the VRS will do next.
0.
Fifteen seconds after the siren chirps begin, the siren’s output will
13
change to a continuous blast.
From this point on, when the ignition key is turned off, the VRS
will immediately turn on the starter kill. This will prevent the
vehicle from being restarted, thus immobilizing it at that spot.
Three minutes after the constant siren output begins, the flashing
parking lights and the siren will stop. The starter kill will remain
active until the system is disarmed. If the door is opened or the
ignition is turned off and on in an attempt to restart the car, the
siren and light flashing will begin again.
39
© 2008 directed electronics
Autogood products «130»
➜ Disarming the VRS
Take the time to familiarize yourself with the VRS triggering sequence and the disarm procedure. It is important to recognize
and identify the VRS trigger sequence and know how to disarm
it in case of accidental activation.
Once the VRS is armed, it does not disarm automatically. You
must disarm it the next time you operate the vehicle. You must
a
disarm it with one of the following procedures:
not started chirping):
m
.u
If the system has not entered the triggered sequence (siren has
1. Turn the ignition on.
on the transmitter for one second. The
co
2. Press
lights will flash and the siren will chirp twice.
0.
If the system has entered the triggered sequence (siren has begun
13
chirping), pressing the disarm button of the transmitter will not
disarm VRS. To disarm the VRS during a VRS trigger sequence:
1. Turn the ignition on.
2. Press the Valet button the preprogrammed number of times to
DRW-35
disarm the VRS system.
note: If the VRS® system has begun its chirping sequence,
the ignition must be turned off, then on to disarm. If you
are driving the vehicle at the time, pull to a safe place
away from traffic and follow the triggered sequence disarm procedure.
40
© 2008 directed electronics
Autogood products «130»
Security & convenience expansions
Here we have listed only some of the many expansion options
available. Please contact your dealer for a complete explanation
of all the options available to you.
Audio Sensor: Metal on glass, glass cracking, and breaking glass
each produce distinctive acoustic signatures. The 506T audio
sensor uses a microphone to pick up sounds, and then analyzes
a
them with proprietary acoustic software to determine if the glass
m
.u
has been struck.
Backup Battery: The 520T keeps the system armed, triggers the
alarm and keeps the starter kill active if main battery power is
co
disconnected.
Field Disturbance Sensor: An invisible dome of coverage is estab-
0.
lished by installing the 508D "radar" sensor. Your security
13
system can then react to any intrusions into this field with the
triggered sequence.
Garage Door: Remote control of your system can go beyond
your vehicle. You can also control your automatic garage door
using the 519H2 garage door opener with your remote control.
Ask you dealer for details. Additional parts and labor required.
Headlight and Parking Light Automation: The 545T Nite-Lite®
will automatically turn on your parking and headlights when it
gets dark. In addition, the 545T will turn your headlights on
whenever the windshield wipers are used. A transmitter function
41
© 2008 directed electronics
Autogood products «130»
can also be used to turn on your parking and headlights for a
programmed time.
Power Trunk Release: The channel two output of the system can
operate a factory power release for the vehicle’s trunk or hatch.
(An additional relay may be required.) If the factory release is not
power activated, then Directed's 522T trunk release solenoid can
often be added.
Power Window Control: Automatic power window control is pro-
m
.u
a
vided with the 529T and 530T systems.
Tilt Sensor: The 507M tilt sensor can be added to your system
to protect your car when its parked. It can protect your vehicle
co
from being lifted to protect your expensive rims.
Valet Start System: For the ultimate in convenience, the Valet
0.
start system can start your vehicle, monitor engine functions,
and power your climate control system with a push of a button.
13
Over-rev protection, open-hood lockout, brake pedal shutoff,
and automatic timer shutoff are all included. (This feature is
only for automatic transmission, fuel-injected vehicles.)
Ultrasonic Sensor: Providing a field of protection inside your car
using the 509U Ultrasonic sensor to protect your belongings.
42
© 2008 directed electronics
Autogood products «130»
Glossary of terms
ASK Amplitude Shift Keying—a method of transmitting data.
Control Unit: The "brain" of your system. Usually hidden under
the dash area of the vehicle. It houses the microprocessor which
monitors your vehicle and controls all of the system's functions.
Fail Safe Starter Kill: An automatic switch controlled by the secu-
m
.u
a
rity system which prevents the vehicle’s starter from cranking
whenever the system is armed. The vehicle is never prevented
from cranking when the system is disarmed, in Valet mode, or
should the starter interrupt switch itself fail. Your system is ready
for this feature, however installation may require additional labor.
co
Input: A physical connection to the system. An input can be
provided by a sensor, pinswitch or through an existing system in
0.
the vehicle, such as ignition or courtesy lights.
13
In-vehicle status LED: A light mounted somewhere in the vehicle.
It is used to indicate the status of your system. It is also used to
report triggers and faults in the system or sensors.
LCD: This is a Liquid Crystal Display used on your remote trans-
mitter to display your vehicles status/alarm information.
Shock Sensor: This is a sensor mounted in the vehicle that is
designed to pick up impacts to the vehicle or glass.
Siren: Noise generating device usually installed in the engine
compartment of the vehicle. It is responsible for generating the
43
© 2008 directed electronics
Autogood products «130»
"chirps" you hear, as well as the six tones you hear while the
alarm is triggered.
Transmitter: Hand-held, remote control which operates the
various functions of your system.
Trigger or Triggered Sequence: This is what happens when the
alarm "goes off" or "trips". The triggered response of your
system consists of the siren sounding and parking light flashing
a
for the programmed duration.
m
.u
Valet Button: A small push-button switch mounted somewhere
inside the vehicle. It is used to override the alarm when a transmitter is lost or damaged, or to enter or exit Valet mode.
co
Warn Away® Response: Lighter impacts to the vehicle will generate
the Warning Zone response. It consists of several seconds of siren
0.
chirps and parking light flashes.
13
Zone: A zone is a separate input that the alarm can recognize as
unique. Each input to the system is connected to a particular
✂
zone. Two or more inputs often share the same zone.
44
© 2008 directed electronics
Autogood products «130»
✂
QUICK REFERENCE GUIDE
To arm using your LCD remote
You can activate, or arm, the system by pressing
on your remote for one
second. When the system arms, you will hear a short siren sound, or chirp, and the
parking lights will flash once. If the vehicle’s power door locks have been connected
to the system, the doors will lock.
To disarm using your LCD remote
➤
To disarm the system, press
. You will hear two chirps, and the parking lights
will flash twice. If power locks are connected to the system, the doors will unlock.
If the siren chirps either four or five times when disarming, see Diagnostics section.
This is called Tamper Alert.
Press
on your remote for two second while the vehicle is running. The system
will chirp once and then once more to indicate that the ignition is on.
m
.u
➤
a
Arming while driving
Disarming without a LCD remote
Turn on the ignition. Press and release the Valet® button the programmed number
of times within 15 seconds. After five seconds, the system will disarm. If it does
not, you may have waited too long. Turn the ignition off and on and try again.
co
➤
To enter or exit Valet® Mode
Turn ignition to RUN position, then turn to OFF position. Press and release the
Valet® button within 10 seconds. The in-vehicle status LED will light solid if you
are entering Valet® Mode, and it will go out if you are exiting Valet® Mode.
0.
➤
13
Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet.
➤
To activate Panic Mode
➤
Press and hold
or
down for approximately two seconds.
To exit Panic Mode
➤
Press
or
on the remote.
To activate Silent Mode™
➤
Press
briefly before arming or disarming, and the confirmation chirp(s) will
be eliminated for that one operation only.
Location of Valet® Button_______________________________
✂
Number of Valet® Button pulses for disarming_____________
45
© 2008 directed electronics
Autogood products «130»
The company behind this system is Directed Electronics
Since its inception, Directed has had one purpose, to provide consumers with the
finest vehicle security and car stereo products and accessories available. The recipient
of more than 100 patents in the field of advanced electronic technology, Directed is
ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America
and around the world.
co
m
.u
a
Call (800) 274-0200 for more information about our products and services.
0.
Directed® is committed to delivering world class quality products
13
and services that excite and delight our customers.
Directed Electronics
Vista, CA 92081
www.directed.com
© 2006 Directed Electronics. - All rights reserved
G3305X 2008-12
Autogood products «130»