838 Series | 738 Series | User manual | MITSUBISHI ELECTRIC ENGINEERING WD-65838 Specifications

3D DLP HOME-CINEMA TELEVISION
™
MODELS
738 Series
838 Series
OWNER’S GUIDE
•
•
•
•
For questions:
-- Visit our website at www.mitsubishi-tv.com.
-- E-mail us at [email protected].
-- Call Consumer Relations at 800-332-2119.
For information on System Reset, please see the back cover.
To order replacement or additional remote controls or lamp cartridges, visit our website at
www.mitsuparts.com or call 800-553-7278.
838 Series. IR emitter cables for NetCommand home-theater control are available for
purchase from Mitsubishi. Call 800-553-7278 and request either part number 242D483020
(two-ended cable) or part number 299P254020 (four-ended cable).
®
Downloaded From TV-Manual.com Manuals
CAUTION
FCC Declaration of Conformity
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user of the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
MAINS DISCONNECTION: The mains plug is used
as the disconnect device. The mains plug shall remain
readily operable.
Stand Requirement
CAUTION: Use these Mitsubishi TV models only with
the Mitsubishi stand models shown here. Other stands
can result in instability and possibly cause injury.
TV Model
Stand Model
WD-60738, WD-65738
WD-65838
MB-S60/65A
WD-73738
WD-73838
MB-S73A
82-inch TVs. Mitsubishi does not design, manufacture, or sell matching bases for 82-inch televisions
(WD-82738, WD-82838). When selecting a stand, base,
or other furniture to support the TV, please make sure it
is designed with the appropriate dimensions for stability and to support the TV’s total weight as well as the
weight of any additional equipment you plan to store.
TV WEIGHT: This TV is heavy. Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and disconnect all cables before moving it.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Product:
Projection Television Receiver
Models:
WD-60738, WD-65738, WD-73738,
WD-82738
WD-65838, WD-73838, WD-82838
Responsible
Party:
Mitsubishi Digital Electronics
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
Telephone:
(800) 332-2119
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and the receiver.
-- Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/
TV technician for help.
Changes or modifications not expressly
approved by Mitsubishi could cause harmful
interference and would void the user’s authority
to operate this equipment.
Note: Features and specifications described in this
owner’s guide are subject to change without notice.
Contents
Important Information About Your TV
Installation and Operating Notes. . . . .
Important Safety Instructions. . . . . . .
. . . . . . . . .
. . . . . . . . .
1 Basic Setup and Operation
Package Contents. . . . . . . . . . . . . . . . .
Before You Begin.. . . . . . . . . . . . . . . . .
First-Time Power-On.. . . . . . . . . . . . . . .
TV Controls. . . . . . . . . . . . . . . . . . . . . .
Remote Control. . . . . . . . . . . . . . . .
The TOOLS Key and Menu. . . . . . . .
TV Control Panel. . . . . . . . . . . . . . .
The STATUS Indicator.. . . . . . . . . . .
Setting Up TV Inputs. . . . . . . . . . . . . . .
Basic TV Operation. . . . . . . . . . . . . . . .
Using the TV with a Personal Computer. .
Downloaded From TV-Manual.com Manuals
7
. 8
. 8
. 9
. 9
10
11
11
12
14
17
. . . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
2 TV Connections
Before You Begin.. . . . . . . . . . . . . . . . . . . . . . .
Connection Types and Audio/Video Quality .. . . .
Inputs and Outputs. . . . . . . . . . . . . . . . . . . . . .
HDMI Device.. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Y Pb Pr Component Video Device. . . . . . . . . . . .
DVI Video Device. . . . . . . . . . . . . . . . . . . . . . . .
Antenna or Cable TV Service.. . . . . . . . . . . . . . .
Composite Video Device.. . . . . . . . . . . . . . . . . .
VCR or DVD Recorder to an Antenna or
Wall Outlet Cable. . . . . . . . . . . . . . . . . . . . . . .
A/V Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . .
A/V Receiver with HDMI Output. . . . . . . . . . . . .
Supplemental Audio Connections. . . . . . . . . . . .
3 TV Features
Sleep Timer.. . . . . . . . . . . . . . . . . . .
FAV (Favorite Channels). . . . . . . . . . .
ChannelView Channel Listings.. . . . . .
Status Display. . . . . . . . . . . . . . . . . .
Using an External Sound System.. . . .
Picture Shape and Display Formats. . .
3D Video.. . . . . . . . . . . . . . . . . . . . .
Camera Images and Music Files. . . . .
USB Source Devices (838 Series)..
Photos and Motion Video as
Composite Video. . . . . . . . . . . .
Using an Audio-Only Device. . . . .
Wireless Audio Playback.. . . . . . .
Sound Projector (838 Series).. . . . . . .
StreamTV™ Internet Media. . . . . . . . .
Introduction to Home-Theater Control.
4
5
19
19
20
22
23
23
24
24
24
25
25
26
4 TV Menus
Main Menu.
Picture. . . .
Sound.. . . .
Captions. . .
Setup. . . . .
Inputs. . . . .
Lock. . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
5 NetCommand IR Control
About NetCommand IR Control.. . . . . . . . . .
IR Emitters. . . . . . . . . . . . . . . . . . . . . . . . .
NetCommand Setup.. . . . . . . . . . . . . . . . . .
Operating NetCommand-Controlled Devices.
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
28
28
29
30
31
32
33
35
35
. . .
. . .
62
63
64
65
6 NetCommand IR Control of an A/V Receiver
Controlling an A/V Receiver after NetCommand
Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Setting Up A/V Receiver Control
Power and Volume. . . . . . . . . . . . . . . . . . . . 69
Automatic Audio/Video Switching Over an HDMI
Connection. . . . . . . . . . . . . . . . . . . . . . . . 70
Appendices
Appendix A: Programming the Remote Control.
Appendix B: Bypassing the Parental Lock. . . . .
Appendix C: HDMI Control of CEC Devices. . . .
Appendix D: TV Care
Lamp-Cartridge Replacement. . . . . . . . . . .
Cleaning Recommendations. . . . . . . . . . . .
Care of the Remote Control.. . . . . . . . . . . .
Appendix E: Troubleshooting. . . . . . . . . . . . . .
Network Service Disclaimer. .
Warranty.
Index. .
.
.
.
75
81
83
.
86
88
88
89
. . . . . . . . .
96
. . . . . . . . . . . . . . .
96
Trademark and License Information. .
. . . . . . . .
. . .
. . .
47
47
51
53
54
57
59
.
.
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
103
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
105
37
37
38
39
43
46
For assistance call 1(800) 332-2119
4
Important Information About Your TV
For Your Records
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
MODEL NUMBER
SERIAL NUMBER PURCHASE DATE
RETAILER NAME LOCATION
Installation and Operating Notes
Custom cabinet installation must allow for proper
air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER
IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND
SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY
AS PRACTICAL.
TV Software
Do not attempt to update the software of this TV with
software or USB drives not provided by or authorized
by Mitsubishi Digital Electronics America, Inc. Nonauthorized software may damage the TV and will not be
covered by the warranty.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Internal Fans
Internal cooling fans maintain proper operating temperatures inside the TV. It is normal to hear the fans
when you first turn on the TV, during quiet scenes
while viewing the TV, and for a short time after shutting
off the TV. You may notice louder fan noise about 30
seconds after shutting off the TV and while using the
Bright Lamp Energy setting.
Lamp Replacement
For lamp-replacement instructions, see Appendix D.
To Order a Replacement Lamp Under Warranty
Call (800) 553-7278. Please have model number, serial
number, and TV purchase date available.
To Purchase a Replacement Lamp After Warranty
Visit our website at www.mitsuparts.com or call (800)
553-7278. Order new lamp part number 915B441001.
Children and TV Viewing
The American Academy of Pediatrics discourages
television viewing for children younger than two years of
age.
5
Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
E XAMP LE OF ANT E NNA G R OUNDING
1) Read these instructions.
2) Keep these instructions.
ANT E NNA
LE AD IN WIR E
G R OUND C LAMP
ANT E NNA
DIS C HAR G E UNIT
(NE C AR T IC LE 810-20)
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
E LE C T R IC
S E R V IC E
E QUIP ME NT
6) Clean only with dry cloth.
G R OUND C LAMP S
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
G R OUNDING
C ONDUC T OR S
(NE C AR T IC LE 810-21)
NE C — NAT IONAL E LE C T R IC AL C ODE
P OWE R S E R V IC E G R OUNDING
E LE C T R ODE S Y S T E M
(NE C AR T 250, P AR T H)
Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.
Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
13) Unplug this apparatus
during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
6
Special Features of Your TV
Your new high-definition widescreen television has
many special features that make it the perfect center of
your home entertainment system, including:
1080p High-Definition DLP Display System
Your Mitsubishi HDTV uses Texas Instruments Digital
Light Processing™ technology for rear-projection TVs
to create the picture you see on screen. All images are
displayed at 1080p. The TV uses Plush 1080p® 5G to
convert lower-resolution signals to 1080p for display.
The TV can also accept 1080p original signals and maintain them at 1080p through all processing until displayed.
3D Television
All Mitsubishi 738 and 838 1080p home-Cinema
HDTV’s can display 3D content originating in several
different formats. This feature lets you experience the
new 3D technologies applied to many recent movies
and video games. Immerse yourself in your favorite
video game, movie, or sporting event displayed in 3D.
16:9 Widescreen Picture Format
Enjoy a full theatrical experience in the comfort of your
home. View pictures as film directors intended them.
Digital TV broadcasts, DVDs and newer video game
consoles support this widescreen format.
Integrated HDTV Tuner
Your widescreen Mitsubishi HDTV has an internal HDTV
tuner able to receive both over-the-air HDTV broadcasts (received via an antenna) and non-scrambled
digital cable broadcasts, including non-scrambled
HDTV cable programming.
High-Definition Video Inputs
•
•
Component Video Inputs. Also called Y/Pb/Pr
inputs, these inputs receive standard analog video
formats of 480i, 480p, plus 720p and 1080i highdefinition signals. This provides a high level of
flexibility when connecting DVD players/recorders,
cable boxes, and satellite receivers.
HDMI Inputs. HDMI® inputs provide additional
high-performance, high-definition connections for
maximum flexibility in your choice of home theater
products. These inputs accept digital 480i, 480p,
720p, 1080i, and 1080p video signals plus PCM
digital stereo signals. The HDMI inputs can also
accept a variety of PC signals and resolutions.
These inputs support Deep Color (up to 36 bits)
and the x.v.Color™ extended color gamut.
Used with an adapter, these HDMI inputs also
accept compatible digital DVI video signals. The
HDMI inputs are HDCP copy-protection compatible.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Easy Connect Auto Input Sensing
Easy Connect™ Auto Input Sensing automatically recognizes when you plug in a device and prompts you to
assign a name to it. The TV ignores any unused inputs,
so the result is an uncluttered menu where you can
easily select devices by name.
Home-Theater Control
HDMI Control
All models. HDMI devices with Consumer Electronics
Control (CEC) capabilities may be compatible with the
TV’s HDMI Control feature. Compatible devices can
receive control signals through the HDMI connection,
allowing the TV’s remote control to operate some functions of these devices.
NetCommand with IR Learning
838 Series. Your Mitsubishi HDTV offers a new level
of networking that seamlessly integrates selected older
A/V products with new and future digital products.
NetCommand® supports IR (infrared) control of products such as DVD players, cable boxes, satellite receivers, and VCRs. The necessary IR emitter cables are
available for purchase separately from Mitsubishi.
Immersive Sound Technology
838 Series. Sound Projector technology uses the TV’s
bank of speakers to create a simulated surround sound
effect by reflecting sound off the room walls.
StreamTV Internet
StreamTV™ brings many popular internet applications to
your TV. Among them is the VUDU™ movie service, offering the largest on-demand HD movie selection anywhere,
featuring full 1080p and 5.1 surround sound. VUDU allows
you to enjoy movies with no store visits, no mailing, no late
fees and no subscriptions.
ENERGY STAR
The following TV models are
ENERGY STAR® qualified:
WD-65738, WD-73738, WD-82738
WD-65838, WD-73838, WD-82838
Products that earn the ENERGY
STAR prevent greenhouse gas
emissions by meeting strict energy
efficiency guidelines set by the U.S.
Environmental Protection Agency
and the U.S. Department of Energy.
1
7
Basic Setup and Operation
Package Contents
Please take a moment to review the following list of
items to ensure that you have received everything.
Installing the Remote Control
Batteries
1. Remove the remote control’s back cover by
Remote Control
2.
Two AA Batteries
AA
AA
Basic Owner’s Guide
3.
gently pressing in the tab and lifting off the cover.
Load the batteries, making sure the polarities
(+) and (-) are correct. For best results, insert
the negative (-) end first.
Snap the cover back in place.
1
The remote
control requires
two AA alkaline
batteries.
Quick Setup Guide
2
Product Registration
Card
838 Series. Calibration
Microphone
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
8
1. Basic Setup and Operation
Before You Begin
1. Review the important safety, installation, and oper2.
ating information at the beginning of this book.
Choose a location for your TV.
• Allow at least four inches of space on all sides
of the TV to help prevent overheating. Overheating may cause premature failure of the TV
as well as shortened lamp life.
• Avoid locations where light may reflect off the
screen.
• See the stand requirements on page 2.
3. Install the batteries in the remote control.
4. Plug the TV into an AC power outlet.
Turning the TV On or Off
•
•
Point the bulb end of the remote control at the
front of the TV and press the POWER key.
Press the POWER button on the TV control
panel.
If You Turn Off the TV by Mistake
•
•
Press POWER again, within about 60 seconds,
to have the TV come back on immediately.
If the STATUS indicator is flashing green, (about
60 seconds after you shut off power), wait a
few moments for the indicator to stop flashing
and press POWER to turn the TV on again.
Controlling Sound Volume
First-Time Power-On
1. Press the
TV key to
ensure that the remote
control is in TV mode.
TV Tips
TV
•
•
Press VOL to adjust the sound level.
See also “Controlling A/V Receiver Sound
Volume” on page 31.
TV
Changing Channels (antenna sources)
NOTE: Perform a channel scan to enable reception of digital channels. See Setup > Channel,
page 55.
•
2. Aim the bulb end of the
remote control at the TV and
press the POWER key
. Wait
for the Welcome screen.
•
•
3. If you wish to change the
menu language to Español,
press .
•
•
•
4. Press
to highlight EXIT.
Press ENTER to clear the
menu.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
•
Enter the channel number using the number
keys on the remote control and press ENTER.
For a two-part digital channel, such as 3-1,
—
press 3 CANCEL 1 to include a dash (separator).
Press CH to change channels one channel at a
time.
Press and hold CH to move quickly through
channels.
Press LAST to return to the previously tuned
channel.
Press GUIDE to display ChannelView channel
listings, highlight a channel, and press ENTER.
Use the Fav (Favorites) feature to tune to up to
nine favorite channels. See page 28.
Use the CH key to tune to preselected groups
of channels using ChannelView custom
channel banks. See page 29.
1. Basic Setup and Operation
9
TV Controls
Remote Control
For more on use and care of the remote control, see
page 88.
Sleep Timer, page 28
Number/letter keys
Channel tuning, page 14
Pass-code entry, page 59,
page 44
Adds a separator in digital channel
numbers. Clears some menu entries.
Emitter (Bulb) End
TV CAB/SAT DVD AUDIO VCR
Press the key for the device type to
control. Leave in TV mode for normal
TV viewing.
Powers TV on or off.
LAST Returns to the previous channel;
moves back one menu
MUTE Mutes the TV speakers.
TOOLS Displays shortcuts for frequently used
features. Press to check if shortcuts
are available for the current device.
See the next page.
FAV
Displays up to nine favorite
sources, page 28.
FORMAT
Changes picture shape,
page 16
VOL Controls volume of TV speakers.
INTERNET
CH Changes channels; moves to another
PAGE page in a menu or list.
Connects to StreamTV internet
content, page 43.
INPUT
Press to select a TV input,
page 14.
ENTER
Selects a channel number or menu item.
Navigation and adjustment
controls
GUIDE ChannelView listings, page 29.
INFO
AUDIO
Audio settings, page 51
VIDEO
Video settings, page 47
MENU
Displays or clears the TV main
menu (page 47). Also steps
back one menu.
TV status or TV help.
(Pause) Freezes a broadcast TV picture.
Record/Playback controls for external devices
When remote control is programmed, page 75
HDMI control, page 85
838 Series: With NetCommand, page 67
Note: To operate other audio/video devices using the
TV’s remote control:
• See Appendix A, “Programming the Remote
Control,” page 75.
• For HDMI devices compatible with the TV’s HDMI
Control feature, see Appendix C, page 83.
Downloaded From TV-Manual.com Manuals
EXIT
Clears all menus.
F1–F4. 838 Series. Special keys for use
with NetCommand IR control of external
devices. See page 64.
• 838 Series
-- See page 62 for NetCommand IR “Learning” of
device keys.
-- For use of specific keys with NetCommandcontrolled devices, see “Special Operation
Methods,” page 65.
For assistance call 1(800) 332-2119
10
1. Basic Setup and Operation
TV Controls, continued
The TOOLS Key and Menu
TOOLS
TOOLS
Press the TOOLS key to check for shortcuts. The Tools menu lists shortcut keys
for common functions. Press the number key to activate the shortcut. See the
sample menu below.
• Shortcuts specific to the current device are in the third column.
• Shortcuts may be available for a CEC-enabled device. See Appendix C,
“HDMI Control of CEC Devices,” page 83.
• 838 Series. After setting up NetCommand control for a device, check the
Tools menu for shortcuts. See page 64.
Sample Tools menu
Tools
PICTURE SOUND
TV
Device-Specific Shortcuts
Availability varies, depending on equipment features and setup.
3 CC
Turns closed captions
on/off
page 53
Sound Shortcuts
Picture Shortcuts
page 47
2 838 Series. Subwoof
Turns on or off audio to a
connected subwoofer.
page 52
838 Series. Select an
Advanced Picture Mode if
previously set up.
page 49
5 Surround
Sound Mode Surround
page 51
7 3D Mode On/Off
page 33
1 Picture Mode Brilliant
4 Picture Mode Natural
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
8 Stereo
Sound Mode Stereo
11
1. Basic Setup and Operation
TV Controls, continued
The STATUS Indicator
TV Control Panel
Buttons on the control panel duplicate some keys on
the remote control.
• To display the main menu, press INPUT and VOL+
simultaneously for about 10 seconds. Press and
hold INPUT and VOL+ for 10 seconds to clear the
menu.
• Refer to upper labels when no TV menus are displayed.
• Refer to lower labels when using TV menus or after
activating a special function.
STATUS
POWER
Symbols
None
TV is powered off. Normal operation.
Green
TV is powered on. Normal operation.
Green
TV powered off, auto-on TV Timer is
set.
Normal operation. TV can be turned on
at any time.
Green
TV just powered off and lamp is
cooling.
Sixty seconds after turning off TV, LED
will start to flash. TV can be turned back
on before flashing starts or after flashing stops, but not while the indicator is
flashing. Normal operation.
Yellow
TV is too hot. The TV will display a
warning message and shut off if it overheats.
• Ambient room temperature may be
too high. Turn off the TV and let the
room temperature drop.
• Clear blocked air vents. Ensure at
least a four-inch clearance on all
sides of the TV.
Yellow
Lamp access door is not secure or no
lamp installed.
TV will not operate until lamp access
door is secured. See Appendix D, page
86.
Red
Lamp failure. Replace the lamp. See
Appendix D, page 86.
Red/
Yellow
TV may require service.
• Hold power button on front panel for
10 seconds to reset TV.
• If LED continues to flash red and
yellow after reset, turn off the TV and
unplug it from the AC power source.
Wait one minute and then plug the
set back in.
• If LED continues to flash red and
yellow, go to www.mitsubishi-tv.com
or call 1-800-332-2119 to receive
Authorized Service Center information.
You may be asked to count how
many times the LED flashes each
color to aid in troubleshooting.
Sample TV controls and STATUS indicator
If the TV fails to respond to the remote control, the
control-panel buttons, or will not power on/off, perform
System Reset. Recent setting changes made before
using System Reset may be lost.
To perform System Reset, press and hold the POWER
button on the control panel for ten seconds.
Panel-Lock Release
•
•
To release the Panel Lock using the TV control
panel, press and hold the INPUT button on the
control panel for ten seconds. If the TV is off, press
the POWER button to have it power on.
To activate the Panel Lock, use the Lock menu,
page 61.
Downloaded From TV-Manual.com Manuals
Steady On
Fast Flashing
LED Color TV Condition
On some models,
open the front cover
to use buttons on the
control panel.
System Reset
Off
Slow Flashing
For assistance call 1(800) 332-2119
12
1. Basic Setup and Operation
Setting Up TV Inputs
Using the ANT (Antenna) Input
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV’s
ANT input. Refer to page 24.
You must perform a channel scan to enable reception of digital channels. If you skip this step, the TV
will receive only analog channels. The channel scan
will search for high-definition and standard-definition
channels available in your area.
Memorizing Channels with Channel Scan
Setting Up Inputs with Auto Input Sensing
1. Power on the TV.
2. Power on the devices to ensure detection.
3. Connect one device to the TV, making note of the
4.
TV input jack.
The TV will display the New Device Found screen if
the connection type is detectable.
Highlight the device type in the on-screen list and
press ENTER. The name you select here will appear
in the Input Selection menu.
For the ANT input
To start channel memorization
1. Power on the TV.
2. Press MENU and open the Setup > Channel menu.
Start channel memorization from the Setup > Channel
menu.
3. Press to enter the Channel menu.
4. Highlight Ant Air if connected to an
over-the-air antenna. Highlight Ant
Cable for service over direct cable
(no cable box). Press ENTER to add a
check.
5. Select the scan type.
•
•
For first-time setup, highlight All
channels.
To scan for channels not already
in memory, highlight New only.
Press ENTER to add a check.
6. Highlight Scan and press ENTER.
Channel memorization may take up
to 15 minutes to complete.
To stop channel memorization before completion,
press CANCEL.
At any time after Channel Scan,
• Use the Setup > Channel > Edit menu (page 55) to
add or delete individual channels from memory.
• Perform an additive scan with the New only option
to add channels not already in memory.
• Repeat the All channels scan if you move the TV
to a new geographic area with a different channel
line-up or reposition the antenna.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Sample New Device
Found screen.
Important Note for NetCommand Users
838 Series. Be sure to select the correct device
type here. Although you can change the device type
later using the Inputs > Name menu, any “learned”
NetCommand IR codes will be erased when you
make the change.
5. Press EXIT to close the New Device Found screen.
6. Repeat the preceding steps for each for each additional device you want to add.
1. Basic Setup and Operation
13
Setting Up TV Inputs, continued
About Auto Input Sensing
Tips on Auto Sensing
This TV’s Easy Connect™ Auto Input Sensing feature
detects the following connections automatically:
• Analog video jacks from inputs 1, 2, and 3
• HDMI inputs (when powered on)
• 838 Series. USB device containing photo and
music files (JPG and MP3 formats).
•
•
Auto Input Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connected device and automatically switch to it.
b. Prompt you to identify the device type.
c. Repeat these steps for other newly detected
devices.
When You First Connect a Device
•
•
•
Most Device Types. Select the device type from
the on-screen list. The device type you select here
will appear as an icon in the Input Selection menu.
A/V Receiver. For an HDMI-equipped A/V
receiver, select AVR from the list of device types if
the A/V receiver is not recognized automatically.
HDMI CEC Devices Compatible with the
TV’s HDMI Control Feature. Compatible
CEC-enabled HDMI-equipped devices are often
recognized automatically by the TV. HDMI Control
may allow you to control some functions of a CECenabled device. See Appendix C, “HDMI Control
of CEC Devices,” page 83.
•
•
•
•
Choose a different name for each input.
The antenna input (ANT) is never detected,
although you can turn off the unused antenna
input in the Inputs > Name menu.
Change the device type displayed in the Input
Selection menu by using the Inputs > Name
menu (page 57).
Some HDMI devices can automatically tell the TV
what name to use in the Input Selection menu
and you will be unable to change the name.
The TV is unable to detect a new connection if
the current input is USB, Bluetooth® (838 Series),
or internet. Switch to a different input before
connecting.
838 series. Any “learned” NetCommand IR
codes will be erased if you change the device
type in the Inputs > Name menu.
Reactivating Auto Input Sensing
for an HDMI Input
After you disconnect an HDMI device, Auto Input
Sensing is temporarily disabled for that HDMI jack.
Perform these steps:
1. Disconnect the HDMI device.
2. Delete the removed HDMI device in the Inputs >
3.
Name menu (see “Removing an HDMI Device,”
page 85).
Connect the new device and the New Device
Found screen will display.
New Device Found screen for a device with HDMI
control enabled. Select On if you want to enable the
TV’s HDMI control of the device. In some cases, as
in the example above, you will also be prompted to
select a device name.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
14
1. Basic Setup and Operation
Basic TV Operation
Selecting an Input to Watch
Watching Broadcast TV
TV Connected to an Antenna or Direct Cable
Service (no cable box)
Note: Perform channel memorization to enable reception of digital channels. See page 12.
1. Press INPUT.
1. Press INPUT to display the Input Selection menu.
2. Highlight the antenna or cable icon and press ENTER.
2. Press
and
to highlight an input icon.
Sample Input Selection menu, antenna input selected
3. To tune to a channel from the ANT input, use any of
Sample Input selection menu, DVD input selected
3. Press ENTER to switch to the input.
4. To control the input device, use the device’s remote
control or see “Introduction to Home-Theater
Control,” page 46.
Note: In most cases, to see a named icon for a connected device (as in the samples), you must first
assign a name either
• When the device is first connected and the
New Device Found menu offers a choice
of names.
• By using the Inputs > Name menu to
assign or change a name at any time after
the TV has detected the connection.
More About the Input Selection Menu
To assign helpful names to the icons, see the
Inputs > Name menu, page 57.
• To remove unwanted Antenna, Bluetooth®, or HDMI
device icons from the Input Selection menu, see
the Inputs > Name menu, page 57.
• To rearrange the icons, see the Inputs > Order
menu, page 58.
•
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
these methods.
• Enter the channel number using the number
keys on the remote control and press ENTER.
For a two-part digital channel, such as 3-1,
—
press 3 CANCEL 1 ENTER .
• Press CH to change channels one channel at a
time.
• Press and hold CH to speed through channels.
•
•
•
•
Press LAST to return to the previous channel.
Use the Fav (Favorites) feature to tune to up to
nine favorite channels. See page 28.
Press GUIDE to display ChannelView channel
listings, highlight a channel number, and press
ENTER to tune.
Set up ChannelView custom channel banks
and use the CH key to tune to predefined
groups of channels. See page 29.
1. Basic Setup and Operation
15
Basic TV Operation, continued
Picture Settings
Basic Audio Controls
1. To get the best picture under different viewing con-
Controlling Sound Volume
ditions, set the Picture Mode first before changing
other video settings. See page 47.
a. Press VIDEO.
b. Press
until Picture Mode
displays.
c. Press
•
•
to make one of these selections:
Name
Brilliant
When to Use
Under bright light
Game
Bright
With gaming consoles (inputs
named Game or PC only)
For most daytime viewing
Natural
For most nighttime viewing
2. Press
3.
4.
•
to display the name of another adjustment.
Press
to make the adjustment.
Press EXIT to clear the display.
Additional picture options are available through these
menus:
Picture > Video
47
General picture appearance.
Picture > Picture Plus
48
Screensaver control
and adjustments for
movies
Picture > Perfect
(838 series)
49
Color fine-tuning
Picture > Advanced
49
Advanced ISF color
controls
Picture > 3D Mode
50, 33 3D video settings
Press VOL to adjust the sound level
of the TV speakers.
See also “Controlling A/V Receiver
Sound Volume” on page 31.
838 Series. Control subwoofer
volume with an on-screen slider.
See page 51. Set Sound > Global
> Subwoofer to On to make this
adjustment available.
Changing Audio Settings (TV Speakers Only)
1. Press AUDIO.
2. Press
to find the adjust-
ment you want. See page 51.
to change.
3. Press
Changing the Audio Output
To switch from the internal TV speakers to an external
sound system,
1. Press AUDIO.
2. Press
to display the TV Speakers option.
3. Press
to change to Off.
TV Care
•
•
Lamp Cartridge. When the lamp cartridge needs
replacement, replace the lamp yourself and save
the cost of a service call. See Appendix D, page
86, for instructions.
General Cleaning. See “Cleaning Recommendations,” page 88.
Assistance
•
•
Downloaded From TV-Manual.com Manuals
For troubleshooting, service, and product support,
see Appendix E, starting on page 89.
For warranty information, see page 103.
For assistance call 1(800) 332-2119
16
1. Basic Setup and Operation
Basic TV Operation, continued
The FORMAT Key and Picture Shape
Repeatedly press the
FORMAT key to cycle
through displays for the
current program. The
TV will remember the
format you last used on
each input.
For details, see page 32
Important
Black bars at the edges of
the screen are common in HD
pictures. Black bars are not a
defect of the TV.
• Black bars are added by broadcasters to fill the 16:9 screen
area while preserving the original
aspect ratio of the picture.
• Your cable box, satellite receiver,
or other device may also be
altering the broadcast picture.
If your device offers output in
native format, try using it with
Mitsubishi picture formats.
Sample Uses of the FORMAT Key
If you prefer to reduce of eliminate black areas at the edges of the picture,
use the FORMAT key.
Press
Squarish 4:3 image is
narrower than the 16:9
screen; unused areas at the
sides are filled with black.
Wide Expand mode stretches
the picture sideways to fill the
screen.
Press
Wide 2.35:1 anamorphic DVD
image; unused areas at the
top and bottom are filled with
black (letterbox effect).
Zoom mode. The picture fills
the screen. All four edges are
cropped in this mode.
More TV Features
Feature
Page
Parental controls (Lock menu)
59
Audio Lock (controls your sound system with
the TV’s remote control left in TV mode.)
76
TV Clock. Set the TV Clock if you plan to use the
TV Timer (page 54) or ChannelView (page 29).
54
Favorite channels or sources
28
ChannelView and custom channel collections
29
Changing the input names that appear in the
Input Selection menu (Inputs > Name menu)
57
3D Video
33
StreamTV™ internet access
43
Programming the remote control to operate
other A/V devices
75
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Feature
Page
Digital camera images as composite video
37
Controlling compatible devices using HDMI
CEC control
83
838 Series. Controlling A/V devices with NetCommand
62
838 Series. Listening to a wireless audio
device with the TV speakers
38
838 Series. Using an external subwoofer.
26
838 Series. Center and rear channel audio
output
27
17
1. Basic Setup and Operation
Using the TV with a Personal Computer
Connecting a Computer to the TV
HDMI Connection
Use one of the connection methods listed below based
on your computer’s video output.
Mitsubishi recommends using high-speed HDMI
cables to connect newer devices incorporating HDMI
technology.
HDMI
HDMI-to-HDMI
cable
R
AUDIO
OUTPUT
Y/ VIDEO
HDMI
2
1
3
Pb
Pr
LAN
R AUDIO L
Y/ VIDEO
ANT
DVI/PC AUDIO
R INPUT L
L
Pb
Pr
(480i / 480p / 720p / 1080i)
INPUT 2
DVI-to-HDMI cable Stereo audio
or an HDMI cable
cables
with a DVI-to-HDMI
adapter
3D
GLASSES
EMITTER
TV main panel
No additional
audio connection is required.
IMPORTANT
This TV accepts digital computer
video signals only. This TV is not
compatible with VGA (analog)
computer video.
HDMI-to-HDMI
cable
Computer with HDMI output
VGA
PC MONITOR OUT
1. Connect the computer’s digital video output to
2.
DIGITAL
AUDIO
OUTPUT
INPUT 1
Audio
Connection
one of the TV’s HDMI jacks. See the connection
diagrams on this page for the method suited to your
equipment.
Connect the computer’s audio output using one of
these options:
• For digital DVI video signals, connect the
analog audio output to the TV’s DVI/PC AUDIO
INPUT jack.
• For HDMI signals, no additional audio connection is required.
Note: If you are unable to hear audio from the
computer, there may be an incompatibility in
the computer’s hardware, software, or internal
settings. Consult a trained computer technician
for advice.
3. Power on the TV and computer. The TV will detect
the connection and display the New Device Found
screen.
An HDMI-to-HDMI connection carries all video and
audio on a single cable.
HDMI and Digital Surround Sound
838 Series. The TV’s HDMI inputs can receive
digital surround sound from an HDMI device. Use an
HDMI connection if you want to hear digital surround
sound from the TV’s internal speaker array.
DVI Video Connection
DIGITAL
AUDIO
OUTPUT
DVI/PC AUDIO
R INPUT L
Y/ VIDEO
HDMI
2
1
3
ANT
AUDIO
R OUTPUT L
Pb
LAN
Pr
INPUT 2
Digital DVI
Video Connection
3D
GLASSES
EMITTER
DVI/PC AUDIO
R INPUT L
R AUDIO L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
INPUT 1
Computer
Video Output
TV main panel
4. In the New Device Found screen, press
5.
to
highlight PC in the list of device types. It is important to use the name PC so that the TV processes
the PC signal correctly.
Highlight EXIT and press ENTER to close the New
Device Found screen.
DVI OUT
R
DVI-to-HDMI
cable
Stereo analog
audio cables
L
AUDIO
Note: If your computer provides digital audio output
(coaxial or optical), you can connect it directly
to a digital A/V receiver and bypass the TV.
Downloaded From TV-Manual.com Manuals
Computer with DVI and
stereo audio outputs
A DVI connection from a personal computer requires a
separate audio connection.
For assistance call 1(800) 332-2119
18
1. Basic Setup and Operation
Using the TV with a Personal Computer
Computer Video Adjustments
1. Power on the computer.
2. Select PC from the Input Selection menu. To do
3.
4.
5.
Tip
Set the computer’s screen saver to display a pattern
after several minutes of inactivity. This acts as a
reminder that the TV is powered on and the lamp
is in use. The lamp is in use whenever the TV is
powered on, even if the screen appears dark.
this, press INPUT to open the Input Selection menu,
move the highlight to the PC icon, and press ENTER.
Working from the computer, change the resolution
of the computer image. View the computer image
on the TV and maximize the computer
resolution while maintaining a suitable
Computer Display Formats
aspect ratio for the image.
Press FORMAT repeatedly to cycle through the TV displays available
Perform TV video adjustments. Press
for your computer’s video signal.
VIDEO repeatedly to access videoadjustment options.
Computer Signal
As Displayed on TV Screen
Press FORMAT repeatedly to find the
4X3
16 X 9
picture shape best suited to the
Original Format
Zoom
Standard
Standard
image. See the chart on this page
showing how different computer resoVGA
lutions can be displayed on the TV.
640 X 480
SVGA
800 X 600
Distortion in Computer Images
Computer images may show distortion
when viewed on the TV, e.g., lines that
should be straight may appear slightly
curved.
Image Resolution
Your Mitsubishi TV can display the resolutions shown in the chart from standard
VGA (640 x 480) through 1920 x 1080
signals at a refresh rate of 60 Hz.
In most cases, the computer will select
the best resolution match to display on
the TV. You can override this setting if you
wish. Refer to your computer operating
system’s instructions for information on
changing the screen resolution.
You may need to restart the computer for
changes to take effect.
Downloaded From TV-Manual.com Manuals
Original Format
Standard
Zoom
Standard
Reduce
XGA
1024 X 768
PC 720p
1280 X 720
WXGA
1360 X 768
SXGA
1280 X 1024
Original Format
PC 1080p
1920 X 1080
For assistance call 1(800) 332-2119
2
19
TV Connections
Before You Begin
Auto Input Sensing
Surround Sound
The TV’s Auto Input Sensing feature automatically recognizes many connections and prompts you to identify
the type of device connected. See page 13 for more on
Auto Input Sensing.
•
Connection Types
•
Use the connection types available on your input
devices that will give the best video quality. For
example, choose HDMI over component video; choose
component video over composite video.
Picture Quality
For best picture quality, route signals directly from the
source device to the TV whenever possible.
For best surround sound audio quality from an
external sound system, route audio-carrying cables
from the source device directly to your sound
system.
838 Series. To use the surround sound capabilities
of the TV’s speaker array, you must connect your
digital surround sound source to the TV on either
-- An HDMI input
-- The ANT antenna input
IMPORTANT
Accessory items such as cables, adapters,
splitters, or combiners required for TV
connections are not supplied with the TV. These
items are available at most electronics stores.
Connection Types and Audio/Video Quality
VIDEO QUALITY
BEST
HDMI
HDMI-to-DVI
AUDIO QUALITY
GOOD
Component
Video
Downloaded From TV-Manual.com Manuals
Composite
Video
BEST
HDMI
GOOD
Digital
Audio
L/R Analog
Audio
For assistance call 1(800) 332-2119
Output/EXTERNAL
CONTROLLER INPUT
HDMI
LAN
3
R AUDIO
Main Connection Panel
CENTER INPUT
(838 series,
page 51)
SUBWOOFER
OUTPUT
(838 series,
page 51)
13
IR– NetCommand
Output
14
(838 series, page 63)
11
DIGITAL
AUDIO
OUTPUT
DVI/PC AUDIO
R INPUT L
ANT
AUDIO
R OUTPUT L
Pb
Pr
LAN
3
2a
USB
(738 Series: power or
wireless adapter, page 44;
838 Series: power only,
page 26 )
L
Y/ VIDEO
3
4
LAN
AUDIO
+
(Ethernet, port analog stereo
input
page 43)
Side Inputs
Pb
Pr
(480i / 480p / 720p / 1080i)
6
7
Y/VIDEO Pb Pr 3D GLASSES
(component
EMITTER
AUDIO/SURROUND
OUTPUT L
video,R page
23)
(page 33)
ANT
(page 24)
INPUT 3
Pr
Pb
Y/ VIDEO
L AUDIO R
6
5
Y/VIDEO
Y/VIDEO Pb Pr
(composite
(component
video, page 23) video, page 24)
For assistance call 1(800) 332-2119
8
Sound Projector Calibration
Microphone Input (page 41)
838 Series. A set of jacks is provided for a camcorder, game, or
other audio/video device.
If you connect a DVI device to
the side HDMI input, use the
nearby audio jacks to send
sound from the device to the
TV.
3D
GLASSES
EMITTER
5
++Y/VIDEO
(composite
video, page 24)
Auto Input Sensing
The TV’s Auto Input Sensing feature automatically recognizes some connections and prompts you to identify the
device type. See page 13.
Downloaded From TV-Manual.com Manuals
AUDIO/SURROUND
R OUTPUT L
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
R AUDIO
1
HDMI
(page 22)
Audio/surround
9b OUTPUT
(838 series, page 25,
page 51)
++
Y/ VIDEO
2
Pb
Pr
(480i / 480p / 720p / 1080i)
9a
10
SUB
WOOFER
OUTPUT
HDMI
1
Y/ VIDEO
Audio
DIGITAL
Audio
DVI/PC AUDIO OUTPUT
(738 series,
OUTPUT
INPUT
(page 25)
(page 23) + page 25)
12
CENTER
INPUT
L
3D
GLASSES
EMITTER
INPUT 1
2
Pr
INPUT 2
1
Inputs and Outputs
Pb
INPUT 2
Y/ VIDEO
2. TV Connections
INPUT 1
20
4
AUDIO
analog
stereo
input
USB
HDMI 4
2b
USB
(multi-use,
pages 26,
35, 44)
1
HDMI
(page 22)
2. TV Connections
21
Inputs and Outputs, continued
1. HDMI® Inputs (High-Definition
Multimedia Interface)
The HDMI inputs support uncompressed standard and
high-definition digital video formats, bitstream Dolby
Digital 5.1, and PCM digital stereo audio. These inputs
are HDCP (High-Bandwidth Digital Copy Protection)
compliant.
2a. USB (limited use)
Standard USB 5-volt, 500-milliamp power output you
can use to supply power to an accessory device.
738 Series. Use this port for a wireless network
adapter. See page 44.
2b. USB (838 Series)
Mitsubishi recommends you use high-speed HDMI
cables to connect newer source devices incorporating
HDMI technology. High-speed cables bring you the full
benefits of Deep Color and x.v.Color.
•
These HDMI inputs can also accept digital DVI video
signals. To connect a device’s DVI output to the TV’s
HDMI input, use an HDMI-to-DVI adapter or cable plus
an analog audio. Connect the audio cable to the DVI/PC
AUDIO INPUT jack on the TV to receive audio from your
DVI device.
•
Use the HDMI inputs to connect to CEA-861 HDMI compliant devices such as a high-definition receiver or DVD
player. These inputs support 480i, 480p, 720p, 1080i,
and 1080p video formats.
The TV’s HDMI inputs are compatible with many DVI-D
and HDMI computer video signals.
HDMI Cable Categories
HDMI cables are available as Standard and
High-Speed types.
• High-Speed HDMI Cables. Newer DVD
players, video games, and set-top boxes require
High-Speed HDMI cables, suitable for clock
frequencies up to 340 MHz or data rates of up
to 10.2 gigabits per second. Use high-speed
cables for 1080p HD signals carrying extended
color encodings (i.e., 30 or more bits, also called
Deep Color). High-Speed HDMI cables are also
suitable for standard HDTV signals.
• Standard HDMI Cables. Standard HDMI
cables may be unmarked. They are suitable for
standard HDTV 720p, 1080i, and 1080p signals
with 8-bit color depth. Use Standard HDMI
cables for clock frequencies up to 74.25 MHz or
data rates of up to 2.23 gigabits per second.
Downloaded From TV-Manual.com Manuals
•
The TV can read JPEG photo files and mp3 music
files from a USB storage device connected to this
input.
Connect a compatible wireless adapter to stream
internet content to the TV (page 43).
This USB port can be used to power accessory
devices.
3. LAN
Use the LAN Ethernet jack for streaming internet video
to the TV. See page 43 for setup.
4. AUDIO
Analog stereo inputs for use in conjunction with adjacent composite or component video jacks.
5. Y/Video (Composite Video)
Analog standard-definition video inputs. Use the adjacent AUDIO R and L inputs if you wish to send audio to
the TV speakers.
6. Y/VIDEO Pb Pr (Component Video)
Analog video inputs able to accept high-definition video
from a high-definition source device. Use the adjacent
AUDIO R and L inputs if you wish to send audio to the
TV speakers.
7. 3D GLASSES EMITTER
Use this jack for the special IR emitter supplied with
some 3D glasses. The emitter sends out an infrared
signal that synchronizes your 3D glasses with the screen
display. See page 33.
8. ANT (Antenna)
Connect your main antenna or direct cable service
(without a cable box) to ANT. The ANT input can receive
digital and analog over-the-air channels from a VHF/
UHF antenna or non-scrambled digital/analog cable
source.
For assistance call 1(800) 332-2119
22
2. TV Connections
Inputs and Outputs, continued
9a. AUDIO OUTPUT
Sends analog audio of the current program to an
analog A/V surround sound receiver or stereo system.
Digital audio from digital channels and HDMI devices is
converted to analog audio by the TV for output on this
jack. This is the only audio connection needed to the
TV if using an analog A/V receiver or stereo system.
Note: If connecting headphones, set Sound > Global >
Analog Audio Out to Variable.
9b. AUDIO/SURROUND OUTPUT
838 Series. Sends out analog audio as described for
other models or can be set for rear surround sound.
Connect external rear speakers to this output for a fuller
surround sound effect from the TV’s speaker array, Set
Sound > Global > Analog Audio Out to Rear (see
“External Rear Speakers” on page 42).
analog audio is converted by the TV to PCM digital audio.
If you have a digital A/V receiver, this is the only audio
connection needed between the TV and your A/V receiver.
12. SUBWOOFER OUTPUT
838 Series. Connect a powered subwoofer to this
input to complement effects from the TV’s speakers.
Set Sound > Global > Subwoofer to On to enable this
output (see “Adding a Subwoofer,” page 26).
13. CENTER INPUT
838 Series. Connect your A/V receiver’s center
channel output to this input to make the TV speakers
output center-channel sound. Set Sound > Global >
Center Channel to On to enable this input. See “Using
the TV Speakers as a Center Channel,” page 27.
14. IR-NetCommand Output
Connect a DVI device to one of the TV’s HDMI inputs
and use this jack to send analog audio to the TV.
838 Series
As an output: Connect IR emitters to this jack to send
NetCommand control signals to external IR-controlled
devices.
11. DIGITAL AUDIO OUTPUT
As an input: Accepts control signals from an external
controller when set up by your professional installer.
10. DVI/PC AUDIO INPUT
This output sends Dolby Digital or PCM digital audio
to your digital A/V surround sound receiver. Incoming
HDMI Device
Mitsubishi recommends using high-speed HDMI
cables to connect newer devices incorporating HDMI
technology. See “HDMI Cable Categories” on the previous page for more on HDMI cable types.
Connect an HDMI cable from the TV to the device’s
HDMI output. HDMI-connectable devices provide
video and audio through a single cable.
Note: The HDMI connection supports copy protection
(HDCP).
HDMI and Digital Surround Sound
738 Series. The TV’s HDMI inputs can receive
digital stereo audio signals only when using the TV
speakers.
838 Series. The TV’s HDMI inputs can receive
digital surround sound from an HDMI device. Use an
HDMI connection if you want to hear digital surround
sound from the TV’s internal speaker array.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
R
AUDIO
OUTPUT
Y/ VIDEO
HDMI
1
2
3
Pb
Pr
LAN
R AUDIO
L
Y/ VIDEO
ANT
DVI/PC AUDIO
R INPUT L
L
Pb
Pr
(480i / 480p / 720p / 1080i)
INPUT 2
Required: HDMI-to-HDMI cable.
DIGITAL
AUDIO
OUTPUT
3D
GLASSES
EMITTER
INPUT 1
Commonly used with an HDTV Cable Box,
Satellite Receiver, or DVD/Blu-ray Player
TV main panel
HDMI-to-HDMI
cable
Any HDMI device
23
2. TV Connections
DVI Video Device
Y Pb Pr Component Video Device
Commonly used with an HDTV Cable Box,
Satellite Receiver, or DVD/Blu-ray Player
If your source device has an HDMI output, use the connections for HDMI devices described on the opposite
page instead of component video.
Required:
RCA-type component video cables
Left/right analog audio cables.
Note: To hear digital surround sound from an A/V receiver, connect the digital audio output from the device
directly to your digital A/V receiver.
Y/ VIDEO
2
3
Pb
Pr
LAN
R AUDIO
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
If you are using a DVI/HDMI adapter, it is important to
connect the adapter to the DVI device for best performance.
Some devices require connection to an analog input
first in order to view on-screen menus and to select DVI
as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.
Note: The HDMI connection supports copy protection
(HDCP).
3D
GLASSES
EMITTER
INPUT 1
HDMI
1
ANT
DVI/PC AUDIO
R INPUT L
L
Required:
Analog stereo audio cables
DVI-to-HDMI cable or DVI/HDMI adapter and HDMI
cable
DIGITAL
AUDIO
OUTPUT
TV main panel
Y/ VIDEO
DVI/PC AUDIO
R INPUT L
R
AUDIO
OUTPUT
ANT
L
Pr
Pb
R– AUDIO –L
Y/ VIDEO
HDMI
2
1
3
Pb
Pr
INPUT 2
AUDIO
OUTPUT
Connect a DVI device (digital only) to one of the TV’s
HDMI input jacks.
LAN
R AUDIO
L
Y/ VIDEO
DVI/PC AUDIO
R INPUT L
Pb
Pr
(480i / 480p / 720p / 1080i)
3D
GLASSES
EMITTER
INPUT 1
R
INPUT 2
DIGITAL
AUDIO
OUTPUT
Commonly used with a Cable Box, Satellite
Receiver, or DVD Player
L
TV main panel
Audio
cables
Component
video cables
Incoming from
cable service or
satellite dish
DVI OUT
DVI-to-HDMI
cable
R
Audio
cables
L
L
R
AUDIO
CABLE IN or
SATELLITE IN
Y
Pb
Component video
device
Downloaded From TV-Manual.com Manuals
Pr
AUDIO
Digital DVI
device
For assistance call 1(800) 332-2119
r
24
2. TV Connections
Antenna or Cable TV Service
Connect the incoming cable to the TV’s ANT input.
Required:
1. Video cables
1a. Component video cables (red/blue/green)
or
1b. Composite video cable (usually yellow)
2. Left/right analog audio cables.
3. Two-way RF splitter
4. Two coaxial cables
Antenna
Direct cable (no cable box)
or
OUT
Note:
Older cable box
Not recommeded. Other
connection types provide
better quality audio and video.
•
ANT
TV main panel
AUDIO
OUTPUT
Y/ VIDEO
HDMI
2
3
Pb
Pr
LAN
R AUDIO
Y/ VIDEO
L
Pb
Pr
(480i / 480p / 720p / 1080i)
Use composite video only if component
video or HDMI are unavailable.
If your recording device has an analog-only
tuner, you must use a digital converter box
to enable recording of digital broadcasts.
ANT
DVI/PC AUDIO
R INPUT L
L
INPUT 2
R
DIGITAL
AUDIO
OUTPUT
TV main panel
3D
GLASSES
EMITTER
R
AUDIO
OUTPUT
1
2
Pb
Pr
LAN
3
R AUDIO
Y/ VIDEO
L
Y/ VIDEO
ANT
DVI/PC AUDIO
R INPUT L
L
Y/ VIDEO
HDMI
INPUT 1
DIGITAL
AUDIO
OUTPUT
1
•
or
Pb
Pr
(480i / 480p / 720p / 1080i)
INPUT 2
IN
3D
GLASSES
EMITTER
INPUT 1
Cable TV
service
VCR or DVD Recorder to an
Antenna or Wall Outlet Cable
ANT
Pr
Pb
Composite Video Device
Required:
Composite video cable (usually yellow)
Analog stereo audio cables.
R
AUDIO
OUTPUT
Y/ VIDEO
2
3
Pb
Pr
3D
GLASSES
R– AUDIO
–L
EMITTER
LAN
R AUDIO
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
L
R
AUDIO OUT
L
AUDIO OUT
COMPOSITE
VIDEO OUT
Audio
cables
or
COMPOSITE
VIDEO OUT
COMPONENT
VIDEO OUT
ANTENNA
IN
DVD Recorder or VCR
Composite
video cable
VCR or other device with
composite video output
Downloaded From TV-Manual.com Manuals
1a.
Y/ VIDEO
TV main panel
R
1b.
INPUT 1
HDMI
1
ANT
DVI/PC AUDIO
R INPUT L
L
INPUT 2
DIGITAL
AUDIO
OUTPUT
2.
Composite
video cable
VCR or other device with composite video
output
For assistance call 1(800) 332-2119
Incoming cable
3.
RF Splitter
4.
4.
25
2. TV Connections
A/V Receiver with HDMI Output
The TV makes all audio available in digital and analog
formats:
• Analog audio coming into the TV is available as
output in digital stereo format on the DIGITAL
AUDIO OUTPUT jack.
• Digital incoming audio is available as analog output
on the AUDIO OUTPUT L and R jacks.
R
Y/ VIDEO
HDMI
1
2
3
Pb
AUDIO
OUTPUT
Pr
DIGITAL
LAN
AUDIO
OUTPUT
R AUDIO
Y/ VIDEO
L
Pb
Pr
(480i / 480p / 720p / 1080i)
ANT
L
INPUT 2
DVI/PC AUDIO
R INPUT L
3DAUDIO
R GLASSES
EMITTER
OUTPUT
L
INPUT 1
DIGITAL
AUDIO
OUTPUT
TV main panel
Digital coaxial
cable (for a digital
A/V receiver)
or
Required: One HDMI-to-HDMI cable
This option allows you to view content from devices
connected to an A/V receiver. The A/V receiver can
send audio and video to the TV over a single HDMI
cable. You can use an HDMI connection as described
here in addition to an audio connection from the TV’s
audio output. The optional audio connection allows you
to hear, through the A/V receiver, devices connected to
the TV only, e.g., an antenna on the ANT input.
• You may be able to use the TV’s remote control
(in TV mode) to operate connected CEC-enabled
HDMI devices. Experiment with your equipment to
determine which functions are available to the TV’s
remote control. See Appendix C, page 83.
• 838 Series: This setup allows you to use NetCommand-controlled audio and video switching over the
HDMI cable. See “Automatic Audio/Video Switching Over an HDMI Connection” on page 70.
To use NetCommand to supplement HDMI
control of a CEC-enabled A/V receiver, note the
recommendations under “More About Using an
HDMI Connection,” page 70.
Stereo analog
cables (for an
analog A/V
receiver)
DIGITAL
AUDIO
OUTPUT
DVI/PC AUDIO
R INPUT L
R
Y/ VIDEO
HDMI
L
2
1
Pb
R AUDIO
L
Y/ VIDEO
ANT
L
Pr
3D
AUDIO
R GLASSES
EMITTER
OUTPUT
DIGITAL
AUDIO
OUTPUT
LAN
3
AUDIO
OUTPUT
INPUT 2
Most setups require either a digital audio cable or
analog stereo audio cables. To send audio from TV
channels received on the ANT input or devices connected directly to the TV, you must use one of the connections shown below.
Pb
Pr
(480i / 480p / 720p / 1080i)
L
INPUT 1
A/V Receiver
TV
OPTICAL
INPUT
COAXIAL
INPUT
Optional
analog or
digital audio
connection
HDMI cable
A/V receiver back panel
Note:
•
•
On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from
the TV as a digital signal. To hear these copyprotected signals through the A/V receiver, use
the connection for an analog A/V receiver.
Check the A/V receiver’s Owner’s Guide for
information concerning use of the digital input
and switching between digital sound and
analog stereo sound from the TV.
A/V receiver with
HDMI output
HDMI OUT
DIGITAL
AUDIO IN
Any connection
types
High-definition
DVD player
R
L
ANALOG AUDIO IN
VCR
DVD player
Cable box
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
26
2. TV Connections
Supplemental Audio Connections
Add a subwoofer to complement the TV speakers with a
fuller bass sound.
•
After connecting a subwoofer, you must enable the
TV’s subwoofer output in the TV’s Sound menu. Go
to Sound > Global > Subwoofer and set it to On.
Mitsubishi recommends Polk Audio Wireless Subwoofer
model PSW i8m. The transmitter module can be
conveniently powered from the TV’s USB power port.
Connect an audio cable to the transmitter to supply
audio from the TV’s SUBWOOFER OUTPUT.
CENTER
INPUT
SUB
WOOFER
OUTPUT
DIGITAL
AUDIO
OUTPUT
Power-only
USB port
Y/ VIDEO
HDMI
1
2
AUDIO/SURROUND
R OUTPUT L
ANT
DVI/PC AUDIO
R INPUT L
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
3
Pb
Pr
LAN
R AUDIO
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
INPUT 2
Adding a Subwoofer
Wireless Subwoofer
3D
GLASSES
EMITTER
INPUT 1
838 Series. Add a subwoofer to complement the TV’s
speaker array or use the TV’s speakers as a center
channel for your external sound system.
SUB
WOOFER
OUTPUT
TV
•
To control subwoofer volume, press the AUDIO key
and then press to find the subwoofer volume
slider. Press
to change the volume.
USB/USB
mini-plug
power cable
RCA/RCA
audio cable
Subwoofer with Audio Cable
Connect the subwoofer directly to the TV’s SUBWOOFER
OUTPUT.
CENTER
INPUT
SUB
WOOFER
OUTPUT
DIGITAL
AUDIO
OUTPUT
AUDIO/SURROUND
R OUTPUT L
ANT
DVI/PC AUDIO
R INPUT L
Setup to send audio signals wirelessly to the subwoofer.
1
2
3
Pb
Pr
LAN
R AUDIO
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
3D
GLASSES
EMITTER
INPUT 1
Y/ VIDEO
INPUT 2
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
HDMI
Polk Audio PSW i8m
powered wireless
subwoofer
SUB
WOOFER
OUTPUT
Subwoofer with audio connection to TV.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
2. TV Connections
27
Supplemental Audio Connections, continued
4. Enable the TV’s center channel mode:
Using the TV Speakers as a Center
Channel
a. Go to Sound > Global and set Center Channel
to On.
If using an external surround sound system, you can
make the TV’s speakers provide center channel sound.
Your A/V receiver must have a center channel pre out
that can supply an amplified center-channel signal to
the TV.
1. Connect your A/V receiver’s HDMI output and
center channel pre out to the TV as shown.
CENTER
INPUT
SUB
WOOFER
OUTPUT
DIGITAL
AUDIO
OUTPUT
AUDIO/SURROUND
R OUTPUT L
ANT
DVI/PC AUDIO
R INPUT L
2
3
Pb
Pr
LAN
R AUDIO
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
HDMI cable
5.
3D
GLASSES
EMITTER
INPUT 1
Y/ VIDEO
HDMI
1
INPUT 2
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
CENTER
INPUT
RCA/RCA
audio cable
A/V receiver
with HDMI
output
Surround sound
source device
HDMI OUT
CENTER
CHANNEL
PRE OUT
b. Press the AUDIO key and press to display
the TV Speakers option. Press
to select
Center.
To balance volume:
a. Power on the A/V receiver and TV.
b. Compare the volume of the TV’s center channel
with the rest of the sound system. If the TV
volume needs adjustment,
i. Turn on the TV speakers. Press AUDIO and
press to display the TV Speakers option.
Press
to select On.
ii. Adjust TV volume using the VOL key.
iii. Return the TV to center channel mode.
Press AUDIO and press to display the
TV Speakers option. Press
to select
Center.
iv. Compare the sound volume. Repeat this
adjustment if needed.
2. Turn on the A/V receiver’s center channel pre out if
needed. See the A/V receiver’s instruction manual.
3. Press the VOL key to adjust TV volume to about level
30.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
28
3
TV Features
Sleep Timer
The Sleep Timer turns the TV off after the length of time
you set. To set the TV to turn on at a certain time of
day, see the Setup > Timer menu on page 54.
Setting the Sleep Timer
FAV (Favorite Channels)
The FAV key gives you quick access to favorite program
sources. Sources can be channels from the ANT input
or devices connected to the TV. You can store up to
nine favorites.
1. Press SLEEP.
2. Press SLEEP additional times to increase the time in
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Adding
1. Press INPUT and switch the TV to the input
you want to add. If adding a channel, switch
to the ANT input and tune to the channel.
2. Press the FAV key.
3. Move the highlight to the number position
you want to assign to the channel or input.
4. Press ENTER.
Removing
Viewing or Changing the Sleep Timer
1. Press SLEEP to display the on-screen message.
2. Press SLEEP additional times to change the time
before the TV powers off. To cancel the Sleep
Timer, press SLEEP repeatedly until OFF is displayed.
Sample Favorites menu. Switch to favorite channels or
inputs using number keys.
1. While watching TV, press the FAV key.
2. In the Favorites menu, highlight the channel
or input you want to remove.
3. Press CANCEL.
Selecting
3.
30-minute increments up to the maximum of 120
minutes.
Press EXIT to clear the screen immediately. Otherwise the screen will clear after five seconds of
inactivity.
1. While watching TV, press the FAV key.
2. Move the highlight to the item you want and
press ENTER. For a shortcut, just press the
number key for the channel or input.
29
3. TV Features
ChannelView Channel Listings
ChannelView displays program descriptions sent by
broadcasters. This information may be unavailable
in some areas.
ChannelView Custom Channel Banks
About ChannelView
ChannelView™ shows memorized channels on the ANT
input. It displays channel names and program information
for digital channels. No program information is displayed
for analog channels. See “Memorizing Channels with
Channel Scan,” page 12 if needed.
ChannelView allows you to set up three banks of custom
channels for convenient access. You can save groups of
channels by content (e.g., news, sports, children’s programming) or by TV user.
Note: You must first set the TV Clock (page 54) to
receive ChannelView listings.
Select a channel bank to customize.
1. Press GUIDE to display ChannelView.
2. Press MENU to move the highlight to the bank
header.
3. Press
to select Bank 1, 2, or 3.
4. With the bank name highlighted, press ENTER to
5.
enter setup mode where you can select channels to
include in the bank.
Press EXIT when finished with setup.
Task
Action
Move between banks
Press
Move into the channel list Press
Add or delete a channel
from the bank
•
ChannelView, “All” tab. Programs are listed on the right.
Using ChannelView Listings
Enter or exit setup mode
Press MENU.
Display/hide ChannelView
listings (ANT input only).
Press GUIDE.
Move through channels
one by one.
Press
Move through channels
quickly.
Press CH.
•
Jump to listings for a specific channel.
Enter the channel number.
Press CANCEL to add a
dash; press twice to clear
the channel number.
•
Tune to a highlighted
channel.
Press ENTER.
Update program information for a highlighted digital
channel.
Press the INFO key (the
screen may briefly go
blank).
Display program descriptions, if available. The
description will appear at
the bottom of the screen.
1. Press to move into
the program area.
2. Press
to move
between programs.
Display more program
description for the current
channel (if available).
Press INFO.
Downloaded From TV-Manual.com Manuals
Highlight the channel
and press ENTER. A
check indicates the
channel has been
added.
Press ENTER again to
clear the check and
remove the channel.
Press CANCEL.
Action
.
.
Remove all channels
from the selected bank
Task
or
•
.
Using Custom Channel Banks
•
While watching TV, press CH. The TV will tune only
to channels stored in the current bank.
To change to a different channel bank:
1. Press GUIDE.
2. Press MENU.
3. Press
.
4. Press EXIT.
To allow tuning to any channel in memory, select
the All bank.
For assistance call 1(800) 332-2119
30
3. TV Features
Status Display
3
Press the INFO key to see
the on-screen status
display. The most
common displays are
shown here.
4
6
1
402-101 KABC
Monday Night Football
2
TV-PG DLSV
St. Louis vs. Tampa Bay, played in Tampa for
5
8
9
10
INFO
7
Sleep 30 min
13
Tuesday 9:10 PM
HD 1080i Standard
Sample information from the
on-screen status display
English
Surround
11
12
14
1. Current Input
2. Audio Indicator. Key:
About Channel Numbers
TV speakers
External sound system
Mute
Channel Numbers for Over-the-Air
Reception or Reception by Direct
Cable
3. Channel number (antenna source only)
Digital channel includes major and sub-channel numbers.
Note: All signals are automatically
converted to 1080p for display.
5.
Standard-Definition Analog Channels
6. Program name (if broadcast); digital source only
Cable Reception
Cable
Channel 3
3
4. Digital channel name (if broadcast); antenna source only.
V-Chip rating
• Antenna source only for digital signal
• Antenna or VIDEO composite jack for analog signal
7. Program description (if broadcast); digital source, antenna
only. Press the INFO key additional times to see more of the
description.
8. Sleep Timer remaining time
480i Stretch
9. Day and time
Receiving Standard-Definition
Analog Signal (480i)
Standard-Definition Digital Channels
Main Channel 7
Sub-Channel 1
Over-the-Air
Antenna Reception
Ant
7-1 KABC-SD
11. Screen format in use
12. Program audio indicator (antenna source only)
13. Available language (digital source, antenna only)
14. Signal-strength indicator (digital source, antenna only)
Signal Definitions
SD 4:3 Stretch
Receiving Standard-Definition
Digital Signal (SD)
High-Definition Digital Channels
Main Channel 7
Sub-Channel 1
Over-the-Air
Antenna Reception
Ant
10. Signal type being received. See “Signal Definitions” on this
page.
7-1 KABC-HD
HD 16:9 Standard
Receiving High-Definition
Digital Signal (HD)
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
480i: Standard-definition, older type interlaced signals from the ANT input,
composite VIDEO, component Y Pb Pr, or HDMI jacks.
480p: Standard-definition progressive-scan DVD signals on component
Y Pb Pr or HDMI jacks.
720p and 1080i: High-definition signals received through component Y Pb
Pr or HDMI jacks. These signals are always 16:9 (widescreen).
1080p: High-definition signals from a PC or Blu-ray player; HDMI inputs only.
SD 4:3: Standard-definition squarish-screen-format signals from digital
channels on the ANT input.
SD 16:9: Standard-definition widescreen-format signals from digital channels on the ANT input.
HD 16:9: High-definition 16:9 widescreen signals from digital channels on
the ANT input.
3. TV Features
31
Using an External Sound System
Redirecting Audio Output
Controlling A/V Receiver Sound Volume
Selecting the Audio Output
Use one of the methods below to control sound volume from
an A/V receiver.
1. Press AUDIO.
2. Press to show the TV
With a Standard TV Setup
3.
Speakers option.
Press to select either On (to
hear sound from the TV speakers) or Off (to hear sound from
an external sound system).
838 Series. Choose Center if using the TV
speakers to supplement audio from an external
sound system. See page 27.
Disconnecting an A/V Receiver
When you disconnect an A/V receiver, change the TV
Speakers setting to On to hear sound from the TV
speakers. Use either the remote control’s AUDIO key or
the Sound > Audio > TV Speakers menu (page 51).
Downloaded From TV-Manual.com Manuals
•
•
•
Recommended Method: Program the TV’s
remote control for your A/V receiver and enable the
Audio Lock feature. See page 76.
Program the TV’s remote control for your A/V
receiver and set the control mode to AUDIO. Return
the control mode to TV to control the TV.
Use the remote control that came with the A/V
receiver.
With HDMI Control (CEC-Enabled HDMI A/V
Receiver)
The TV’s remote control may control some functions of
the A/V receiver. See Appendix C, “HDMI Control of
CEC Devices” on page 83.
With NetCommand IR Control
838 Series. Set up NetCommand control of the A/V
receiver’s volume functions in the Inputs > AVR menu.
The TV’s remote will then control A/V receiver volume.
See page 69.
For assistance call 1(800) 332-2119
32
3. TV Features
Picture Shape and Display Formats
Format Definitions
Note: See page 16 for use of the FORMAT key to apply
the formats described here.
Standard: The full-screen format used by HDTV
signals. Use this format to display anamorphic DVDs
with a 1.78:1 or 1.85:1 aspect ratio. Anamorphic DVDs
with a 2.35:1 aspect ratio are displayed correctly but
with top and bottom black bars. Squarish (4:3) images
are stretched evenly from side to side. Available for all
signals.
Expand: Enlarges the picture to fill the screen by
cropping the top and bottom; useful for reducing the
letter box top and bottom bars of non-anamorphic DVD
images.
Zoom: Enlarges the picture to fill the screen by cropping the sides, top, and bottom to eliminate black bars.
• 480i/480p and SD 4:3 signals: Eliminates top and
bottom bars on anamorphic DVDs with a 2.35:1
aspect ratio.
• 720p, 1080i, SD 16:9, and HD signals: Eliminates
bars added to squarish 4:3 images.
Stretch: Stretches a squarish 4:3 image across the
screen to display the entire image with less distortion
than the Standard format.
Stretch Plus: Similar to Stretch, but minimizes distortion on the sides by expanding the picture to crop off
portions of the top and bottom. Use
to adjust the
vertical position of the picture.
Effect of Mitsubishi Formats on Picture Types
Original
Signal
TV
Display
Format
Non-anamorphic or SD 4:3
Anamorphic DVD
Narrow: Displays narrow 4:3 images in their original shape. Adds black side bars to fill the screen.
Wide Expand: Enlarges the picture, cropping the
image on both sides. Removes or reduces black
side bars added to narrow images converted to
16:9 signals for digital broadcast.
Note: All high-definition channels send widescreen (16:9) signals, but not all programming was
created for the widescreen format. The broadcaster may stretch the image or add side bars to
fill the widescreen area.
Standard
Distorted; Not
recommended.
Expand
Recommended
for letterbox. See
Note 1.
Distorted; not recommended. See Note 1.
Zoom
Distorted; Not
recommended.
See Note 1.
Recommended for
anamorphic 2.35:1
images. See Note 1.
Stretch
Recommended
for standard
broadcasts. See
Note 1.
Distorted; not recommended. See Note 1.
Image information may be stated on the DVD
case. Some DVDs support both formats
described below.
Stretch
Plus
Recommended
for standard
broadcasts. See
Note 1.
Distorted; not recommended. See Note 1.
Anamorphic (or Enhanced for WideScreen TV)
Indicates DVDs recorded to show widescreen
images properly on 16:9 TV sets using the TV’s
Standard format mode (recommended).
Narrow
See Note 1
Distorted; not recommended. See Note 1.
Recommended
Note 1: Available for 480i, 480p, and digital SD 4:3 signals only.
Original Signal
SD 16:9 or
HD Digital
720p, 1080i,
1080p Signal
Display Formats
Wide Recommended to reExpand move side bars.
Zoom
Recommended to remove bars from the top,
bottom, and sides.
TV Display Formats. Press the FORMAT key repeatedly to see
different displays for the current program. Press the INFO key to
see the name of the format in use.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
DVD Image Definitions
Non-Anamorphic (or 4:3, 1.33:1, Letter Box, or
Full Screen)
Indicates DVDs recorded for viewing on squarish TV screens. They may be full screen (4:3 or
1.33:1) which crops movies to fit the narrow TV, or
letter box, which adds black top and bottom bars.
3. TV Features
33
3D Video
To display 3D gaming or 3D cinema content, your
Mitsubishi TV requires:
• A compatible 3D source device outputting a 3D
signal in one of these formats:
-- Checkerboard format, 1080p, 60-Hz; (lower
resolutions may be supported but will not fill the
screen)
-- Side-by-Side format, 1080p, 24/30/60 Hz; 720p,
60 Hz
• Active-shutter 3D glasses, DLP link type or IR
emitter type with matching emitter
Please visit our website at www.mitsubishi-tv.com for information about future TV software updates that will broaden
3D signal compatibility.
Initial Setup
1. If your 3D glasses came with an emitter box,
Watching 3D Video
Note: Active 3D glasses are required.
1. Press INPUT.
2. Highlight the icon for the 3D video device and press
3.
4.
5.
6.
ENTER.
Press MENU and select the Picture > 3D Mode
menu.
Select On for 3D Mode. The On setting will be
memorized for the current input when you exit this
menu.
Select the Source Format. If your source device
outputs an unsupported signal format see “Notice
Concerning Format Compatibility” on this page.
For Glasses Control, select the control type for
your 3D glasses, either IR Emitter or DLP Link.
connect the emitter box to the 3D GLASSES
EMITTER jack. Place the box in front of the TV
where there is a clear path to the glasses.
Note: If your glasses are marked DLP Link, skip this
step; no emitter box is required with DLP Link
technology.
R
AUDIO
OUTPUT
ANT
L
CENTER
INPUT
SUB
WOOFER
OUTPUT
DIGITAL
AUDIO
OUTPUT
R
AUDIO
OUTPUT
ANT
DVI/PC AUDIO
R INPUT L
L
1
2
Pr
3
INPUT 2
Pr
LAN
R AUDIO
b
Pr
480p / 720p / 1080i)
Pb
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
3D
GLASSES
EMITTER
INPUT 1
Y/ VIDEO
HDMI
INPUT 2
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
INPUT 1
b
3D
GLASSES
EMITTER
+
AUDIO/SURROUND
R OUTPUT L
++
Use the Picture > 3D Mode menu to enable 3D video.
2. Power on the TV and the source device.
3. Connect the source device to the TV’s HDMI input.
4. When the New Device Found screen displays,
5.
name the input.
Press EXIT to close the New Device Found screen.
AUDIO/SURROUND
R OUTPUT L
Notice Concerning Format Compatibility
Mitsubishi 3DTVs (738 and 838 series) currently support
the side-by-side 3D signal format. For support of other
3D formats, such as top-bottom and frame packing (3D
Blu-ray standard), Mitsubishi 3D TVs will require the use
of a 3D source device that outputs the 3D checkerboard
format or a 3D source device coupled with the Mitsubishi
3D adapter. In all cases an emitter and matching 3D active
shutter glasses or DLP Link active shutter glasses are
required in order to view 3D content.
Downloaded From TV-Manual.com Manuals
7. Press EXIT to close the menu.
8. If the image does not appear correct (e.g., objects
appear to be moving in instead of out), open the
Picture > 3D Mode menu and set Glasses L-R to
Reverse.
To Watch Regular (non-3D) Video
The 3D Mode setting is memorized for each input.
When you want to watch non-3D video on the input
selected above, you can
• Open the Picture > 3D Mode menu and set 3D
Mode to Off.
• Press the TOOLS key and select 3D option 7.
For assistance call 1(800) 332-2119
34
3. TV Features
3D Video, continued
3D Safety Requirements
•
3D Glasses are NOT designed as sunglasses or
safety glasses and do not provide protection. 3D
glasses should be worn only when viewing 3D
material.
• Do not wear the wireless glasses in any situations
that require unimpaired visual perception.
• Children under the age of 5 should not view 3D
programming.
Under normal conditions, 3D viewing is safe for your
movies or games. Some people may experience discomfort, however. To minimize the potential for experiencing visual problems or any adverse symptoms:
• Read and follow any and all safety warnings that
accompany your 3D glasses or 3D source devices.
• Maintain a distance of no less than 2 to 2.5 times
the screen height measurement away from the
display. Viewing from too short a distance can
strain your eyes.
• Take regular breaks, at least 5 minutes after every
hour of 3D viewing.
If you experience any of the following symptoms, discontinue 3D viewing until the symptoms go away:
• nausea, dizziness, or queasiness,
• headache, or eyestrain,
• blurry vision,
• double vision that lasts longer than a few seconds,
Do not engage in any potentially hazardous activity
(for example, driving a vehicle) until your symptoms
have completely gone away. If symptoms persist,
discontinue use and do not resume 3D viewing without
discussing your symptoms with a physician.
Do not use the glasses where loss of balance or limiting your field of vision may be dangerous to you.
Do not use near staircases, ledges or balconies. You
may risk falling during or after use.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Epilepsy
WARNING! IF YOU OR ANY MEMBER OF YOUR
FAMILY HAS A HISTORY OF EPILEPSY, CONSULT
A PHYSICIAN BEFORE USING 3D VIDEO OR GAME
PRODUCTS.
A small percentage of the population may experience
epileptic seizures when viewing certain types of TV
images or video games that contain flashing patterns of
light.
The following people should consult a physician before
viewing 3D Games or Video:
• Anyone with a history of epilepsy, or who has a
family member with a history of epilepsy
• Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing
light effects.
WARNING! SOME LIGHT PATTERNS MAY INDUCE
SEIZURES IN PERSONS WITH NO PRIOR HISTORY
OF EPILEPSY. DISCONTINUE 3D VIEWING IF YOU
EXPERIENCE ANY OF THE FOLLOWING SYMPTOMS:
• Involuntary movements, eye or muscle twitching
• Muscle cramps
• Nausea, dizziness, or queasiness
• Convulsions
• Disorientation, confusion, or loss of awareness of
your surroundings
Do not engage in any potentially hazardous activity (for
example, driving a vehicle) until your symptoms have
completely gone away.
Do not resume 3D viewing without discussing the
symptoms with your physician.
3. TV Features
35
Camera Images and Music Files
•
•
•
•
All Models. The TV can display still images or
motion video from a camera through the Y/VIDEO
port. See page 37.
All Models. To play music through the TV speakers from an audio-only device, see “Using an
Audio-Only Device,” page 37.
838 Series. The TV can read photo and music
files from a USB device. Photos must be in JPEG
format and music files must be in mp3 format. To
play music files while displaying a photo slide show,
see “USB Media Setup Menu” on the next page.
838 Series. The TV can play music wirelessly
using Bluetooth® technology. See page 38.
The USB Media Player Menu
USB Media menu, Photos option selected
Displaying the Menu
1. Back up the data on your USB drive before connecting it to the TV. Mitsubishi is not responsible
for any file damage or data loss.
2. Connect your USB drive to the TV’s USB port.
The USB Media Player menu displays while files
are being read. Wait until icons appear in the menu
before continuing.
INPUT 3
Pb
Y/ VIDEO
L AUDIO R
USB
light one of these choices and press ENTER.
Photos
View photos or play a slide show
Audio
Listen to audio tracks or a playlist.
Setup
Perform setup for a slide show or playlist.
If music and image files are both present,
lets you play a slide show with music.
Notes on Using the USB Port
• The TV ignores all commands while reading files.
• Large files or high-capacity storage devices may
take a long time to display.
• The TV can read files up to 10 MB in size with a
maximum of 2,500 files stored on the device. The
FAT16 or FAT32 file system is recommended.
• Use a USB drive instead of a card reader.
• Back up the data on your USB drive before connecting it to the TV. Mitsubishi is not responsible
for any file damage or data loss.
USB Source Devices (838 Series)
Pr
3. When the USB Media Player icons display, high-
HDMI 4
Note: Some manufacturers’ devices may be incompatible with the TV. If the TV is unable to display your photos, you can:
• Transfer files to a different USB device.
• Use your digital camera’s composite video
output. See page 37.
Picture Files Compatible with the USB Port
• Still images recorded on digital cameras using the
Exchangeable Image File Format, version 2.1 (EXIF
2.1) standard for digital still cameras and Design
Rules for Camera File Systems version 1.0 (DCF 1.0)
• Some images opened and resaved on a computer
may not play back or may not display in the thumbnail list. This happens if the files were resaved in an
incompatible format.
•
Full path file names can be no longer than 50 characters and must end in a .jpg extension. Only the
first 20 of the 50 characters will display.
The TV can read JPEG files as created by the
camera. If you edit a picture file on a computer
and resave the image, the TV may be unable to
read the resaved file.
838 series. The TV can read photo
and music files from the USB port.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
36
3. TV Features
Camera Images and Music Files, continued
Using the Photos and Audio
Menus
Use these keys with your photo and audio files.
Key
Use the USB Media Setup menu to set up play of a
slide show or playlist.
For Photos or Audio Tracks
•
•
or
ENTER
USB Media Setup Menu
Moves the highlight left/right through
icons to select Photos, Audio, or
Setup.
Moves the highlight from item to item.
Plays the slide show or playlist starting
from the highlighted item.
Pauses a slide show or playlist.
Stops a slide show or playlist.
•
•
•
•
GUIDE
Highlights the first or last item on the
current page.
Skips to the previous or next item
during play.
Displays the previous or next page of
items.
Skips immediately to the previous or
next item during play.
Rotates an image clockwise in 90˚ increments.
INFO
Displays the item name during play. Press
EXIT to clear.
EXIT
Clears file information from the screen.
MENU
Displays the main menu; stops play.
INPUT
Displays the Input Selection menu; stops
play.
IMPORTANT
Always stop playback with
(STOP) or change to
a different TV input before disconnecting your USB
device.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
•
•
•
•
•
If JPEG image files and mp3 files are both on the
USB device, choose from:
-- Slideshow + Music
-- Slideshow only
-- Music only
Interval. Select the type of time interval for display
of each slide. The intervals may be longer for larger
files than for smaller ones.
Frequency. Select the number of times (frequency)
to play the complete slide show and/or playlist.
Show File Names. Choose Automatic or Off.
Press EXIT to close the USB Media Setup menu and
return to the USB Media Player menu.
37
3. TV Features
Camera Images and Music Files, continued
1. Refer to the owner’s manual supplied with the
camera for instructions needed for this setup.
2. Set the camera’s output signal type to NTSC and
3.
put the camera into playback mode.
With the camera still turned on, connect your digital
camera’s composite video cable (usually yellow) to
the TV’s Y/VIDEO jack. To hear audio, connect the
camera’s audio output cable to the AUDIO L jack.
CENTER
INPUT
SUB
WOOFER
OUTPUT
DIGITAL
AUDIO
OUTPUT
AUDIO/SURROUND
R OUTPUT L
All Models. To use the TV speakers with an audio
device such as an MP3 or CD player with analog output,
follow these steps.
1. Insert an unused RCA-style connector into the
Y/VIDEO jack associated with the TV’s analog audio
input. The presence of this connector activates the
TV’s auto-detection.
2. When the TV detects the Y/VIDEO connector, it will
display the New Device Found screen. Name the
new input CD/Audio or MP3 Player.
3. Connect left (white) and right (red) audio cables
from AUDIO OUT on the device to AUDIO L and R on
the TV.
4. Keep the connector in the VIDEO/Y jack while using
the audio-only device.
ANT
DVI/PC AUDIO
R INPUT L
CENTER
INPUT
SUB
WOOFER
OUTPUT
1
2
Pb
Pr
LAN
3
R AUDIO
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
DIGITAL
AUDIO
OUTPUT
3D
GLASSES
EMITTER
AUDIO/SURROUND
R OUTPUT L
Y/ VIDEO
HDMI
1
2
3
L
Pb
Pr
LAN
R AUDIO
R AUDIO
ANT
DVI/PC AUDIO
R INPUT L
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
INPUT 1
Y/ VIDEO
HDMI
INPUT 2
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
Y/ VIDEO
R AUDIO
Optional
Audio Cable
Audio-only
device
2.
L
INPUT 2
All Models. Connect the camera to the TV using a
composite video cable and control the slide show or
movie through the camera. The display resolution will
be standard-definition (480i).
Using an Audio-Only Device
3D
GLASSES
EMITTER
INPUT 1
Photos and Motion Video as Composite
Video
TV
Y/ VIDEO
Unused
RCA-style plug
(plug in first)
1.
Camera connection using a composite video cable
4. When the New Device Found screen displays,
5.
6.
assign the name Camcorder.
Press EXIT to close the New Device Found screen.
Highlight the icon for the camera input and press
ENTER.
7. If viewing photos, control the slideshow from the
camera. Advance through the images manually or
check if the camera can advance automatically.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
38
3. TV Features
Camera Images and Music Files, continued
Wireless Audio Playback
838 Series. The TV’s built-in speaker array can play
audio from a handheld device using Bluetooth® A2DP
(stereo audio) wireless technology. The TV can be
paired with only one device at a time.
Tips for Wireless Playback
•
•
Pairing the TV with an Audio Playback Device
1. Turn on the wireless device you wish to use for
•
2. Press INPUT to display the Input Selection menu.
•
playback.
•
Selecting the Bluetooth icon at a later time will
connect the TV again to the paired device.
If the paired device is not available, the TV will
accept pairing from a different device.
Once connection is lost, the TV will power off after
five minutes without receiving a signal.
To clear a paired device, turn off the Bluetooth icon
(Inputs > Name menu) or pair the TV with a different device.
To remove the Bluetooth icon from the Input
Selection menu, turn off the icon in the Inputs >
Name menu.
Bluetooth icon in Input
Selection Menu
3. Highlight the Bluetooth icon and press ENTER.
4. Wait for the pairing menu to display. Pair your device
with the TV and then connect. Some devices pair and
connect automatically, while others require you to enter
the TV pass code displayed.
Note: If you have difficulty pairing, turn off all other
Bluetooth wireless devices in the area.
5. Use keys on the TV’s remote control to control playback. Not all keys work for all devices.
Skip a track
(Pause)
(Stop)
(Reverse)
(Play)
(Forward)
Resetting Bluetooth Pairing or Connection
Perform this reset if the audio device does not connect
properly to the TV.
1. If the audio device has been previously paired with
2.
3.
4.
5.
the TV, delete the TV from the device’s paired list.
Go to the TV’s Inputs > Name menu and highlight
the Bluetooth icon. Press ENTER to select Off.
Press EXIT.
Go to the Inputs > Name menu and highlight the
Bluetooth icon. Press ENTER to select On.
Press EXIT.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Remove the Bluetooth icon from the Input Selection
menu by turning off Bluetooth in the Inputs > Name
menu.
3. TV Features
39
Sound Projector (838 Series)
This setup is unnecessary if using the TV speakers
as a center channel. See page 27.
Sound Projector Technology
838 Series. The TV’s built-in speaker array can be
adjusted to reflect sound off the room walls to create a
surround sound effect. Setup can be performed either
manually or automatically.
• To create the surround sound effect, the room walls
must reflect sound and not be covered with soundabsorbent material.
• Repeat the setup procedure if you reconfigure the
room’s walls or furnishings.
Before You Begin
Positioning the TV
•
•
Center the seating area in front of the TV and at
least six feet away from it.
Arrangements that give good results:
Connecting the TV
To hear digital surround sound, the TV must be connected to a digital surround sound source. The TV can
receive digital surround sound from:
• Any HDMI jack
• The ANT input (from some digital broadcasts)
Other stereo connections will provide Dolby Pro Logic
surround sound.
Basic Manual Setup
Note: If you have already performed Auto setup, do
not make manual adjustments. Doing so will
erase all settings created during Auto setup.
1. Press MENU and go to Sound > SoundPro.
2. Enter the room dimensions and layout information
requested in the screen. To change measurements, press
.
•
If the room is an odd shape, locate the TV to take
best advantage of wall reflections.
3. Press EXIT to exit and save settings.
4. Play some sample audio to check sound quality.
If further adjustment is needed, use the Custom
menu as described next.
Custom Menu
Use the Custom menu after defining the room layout.
•
Avoid locations that may distort sound reflections.
For a room with large areas of curtains that might affect
sound reflection, do the following:
a. Open the curtains fully to improve sound reflection.
b. Set angles by performing the procedure in
“Adjusting Beam Angles.”
c. Close the curtains.
d. Set levels by performing the procedure in
“Adjusting Levels.”
1. From the Sound > SoundPro menu go to the
CUSTOM menu.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
40
3. TV Features
Sound Projector (838 Series), continued
How to Make Adjustments in the Custom Menu
• Press
to select an audio beam; colors of the
adjusters correspond to audio beams in the onscreen diagram.
• Press
to redirect the audio beam or change
the sound level.
2. Position yourself in your usual viewing location.
Remain in this position, looking at the TV, while
making the following adjustments.
3. Adjusting Beam Angles
a. Adjust Center Beam Angle until sound is
about equal in both ears.
b. Adjust Left Beam Angle to maximize sound
heard from the front left side.
c. Adjust Right Beam Angle to maximize sound
heard from the front right side.
d. Adjust Left Surround Beam Angle to where
the sound seems to come from the left rear
side. If this cannot be achieved, make the
setting the same as that for Left Beam Angle.
e. Adjust Right Surround Beam Angle to where
the sound seems to come from the right rear
side. If this cannot be achieved, make the
setting the same as that for Right Beam Angle.
Controls in the SoundPro
> Custom menu adjust the
direction and focus of the TV’s sound output.
At extreme beam angles, adjustment may be
limited and the image on screen may not accurately
represent the sound beams.
4. Adjusting Levels
a. Adjust Center Level to the mid level.
b. Adjust the following levels one at a time so that
each one sounds about the same as the center
level:
Left Level
Right Level
Left Surround Level
Right Surround Level
c. Check all sound levels by quickly switching
between them using
.
d. Readjust individual levels in small increments
and recheck as above until all sound levels
seem about the same.
5. Adjusting an External Subwoofer
Note: Set Sound > Global > Subwoofer to On to
make this adjustment available.
a. Play sample video or music containing lowfrequency bass sound.
b. Press AUDIO. Use
to display the Subwoofer option.
c. Press
to adjust the subwoofer volume.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Adjust the volume level of individual audio beams
using sliders in the SoundPro > Custom menu.
Resetting Angle and Level Values in the Custom
Menu
Follow these steps to return settings to the default
values.
1. Press EXIT to clear all menus.
2. Press MENU. Go to the Sound > SoundPro menu
and press ENTER.
3. Change any setting (e.g., TV Location).
4. Press EXIT to clear all menus.
5. Press MENU. Go to the Sound > SoundPro menu
6.
7.
and press ENTER.
Enter the correct values for the room layout.
Return to the CUSTOM menu to adjust angles
and levels.
41
3. TV Features
Sound Projector (838 Series), continued
Auto Setup
Auto setup uses the included calibration microphone to
optimize Sound Projector performance for most room
conditions.
Initial Preparation
1. Position and connect the TV as described under
2.
3.
“Before You Begin,” page 39.
Power on the TV and external subwoofer, if any.
Plug the microphone cable into the TV’s INPUT 3
audio jack.
Connect microphone
to the right (red) audio
jack.
Microphone Placement
• Make sure there are no large obstacles between
the TV and microphone.
• Place the microphone
-- On a flat, level surface at least six feet away
from the front of the TV.
-- On a tripod or on the backrest of your
seating.
-- At the same height your ears would be when
watching TV. The height must be within 3
vertical feet of the height of the TV’s speaker
array.
-- Centered in front of the TV, not off to the
side.
L AUDIO R
TV
Height of TV
speaker array
6 ft. minimum
4. Place the microphone as described in the guidelines on this page.
Start Auto Setup
or
5. Press MENU and go to Sound > AutoSP.
6 ft. minimum
3 ft.
6. Highlight START and press ENTER.
Microphone
Set the microphone
on a level surface at
ear height at least
six feet from the TV.
Use a seat backrest
or tripod so as to
pick up sound from
all directions.
Maximum height above speakers
Height of TV
speakers
3 ft.
Be sure the
height of the
microphone is
within three feet
of the speaker
height.
3 ft. exit the room right away. The calibration
7. Quietly
sequence will start in a few seconds and may be
loud. It is important to leave the room as your presMinimum height
below
speakers
ence will
interfere
with the calibration process.
8. Wait for completion of setup before returning to the room.
9. Play some sample audio material to check the
sound quality.
Microphone
Center the microphone in front of
the TV.
Note: Do not perform manual adjustments after running Auto setup, as this will erase all settings
defined during Auto setup.
10.Store the microphone out of direct sunlight and
away from heat.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
42
3. TV Features
Sound Projector (838 Series), continued
External Rear Speakers
CENTER
INPUT
Transmitter
DIGITAL
AUDIO
OUTPUT
DVI/PC AUDIO
R INPUT L
ANT
AUDIO/SURROUND
R OUTPUT L
Y/ VIDEO
HDMI
1
2
3
Pb
Pr
LAN
R AUDIO
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
INPUT 2
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
3D
GLASSES
EMITTER
INPUT 1
You may wish to supplement surround sound from the
TV with external rear speakers. External speakers can
fill in rear sound if your room lacks a rear wall suitable
for reflecting sound. Mitsubishi recommends Polk
Audio’s F/X Wireless Surround system.
SUB
WOOFER
OUTPUT
AUDIO/SURROUND
R OUTPUT L
TV
To TV audio
outputs
Transmitter
Polk Audio F/X
Wireless Surround
speaker unit
To left and right
audio inputs
Connecting the transmitter to the TV
Sample room layout without a back wall suitable for rear
sound reflections
1. Position the external speakers as needed for rear
sound.
2. Connect analog audio output from the TV to the
3.
4.
Polk Audio F/X Wireless Surround transmitter.
Power on the TV, speakers, and transmitter.
Set Sound > Global > Analog Audio Out to Rear.
Sound Projector adjustments when using external rear
speakers.
5. Adjust the sound output. Go to the Sound >
SoundPro > CUSTOM menu. Review the instructions in .
a. Adjust beam angles for the left, right, and
center beams. Because the external speakers
output left and right surround beams and they
do not appear in the adjustment image.
b. Adjust volume levels for all audio beams.,
including the left and right surround beams.
6. Play sample audio to check the sound. Repeat any
of the adjustments as needed.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
3. TV Features
43
StreamTV™ Internet Media
Internet services provided by VUDU™ Apps let you
access many popular on-line applications. In addition
to free content, VUDU’s movie service lets you buy and
rent movies through the TV. Visit www.VUDU.com to
learn more about available movie titles, prices, and services offered. For a list of recommended routers and
switches, see the Support > Knowledge Database
section at VUDU.com.
Note: From time to time you may notice changes to
the internet interface as new features are added.
Required for StreamTV internet media:
• Broadband internet service (at least 2 Mbps for SD,
4 Mbps for HD, and 8 Mbps for 1080p HDX)
• Ethernet cable or to connect wirelessly, an AzureWave AW-NU231 USB wireless adapter.
• Computer access to the VUDU.com website
(required for initial account activation).
• A credit card for rental and purchase transactions
from VUDU’s movie service.
2. Open the Setup > Network menu to review set-
Home Network Setup
Before using StreamTV internet media, you must
connect the TV to the internet using one of these
methods.
tings.
Note: Make sure the TV is on any input other than the
USB port or Bluetooth®. Press the INPUT key to
change.
Ethernet Connection
DHCP (automatic)
1. Connect the TV to your network router with a
Category-5 Ethernet cable (not supplied).
SUB
WOOFER
OUTPUT
R
AUDIO
OUTPUT
Y/ VIDEO
HDMI
1
2
3
Pb
Pr
LAN
R AUDIO
ANT
AUDIO/SURROUND
R OUTPUT L
L
LAN
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
INPUT 2
DIGITAL
AUDIO
OUTPUT
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
3D
GLASSES
EMITTER
INPUT 1
CENTER
INPUT
Downloaded From TV-Manual.com Manuals
3. Press EXIT to clear the menu.
Manual
TV Main Panel
Router or modem
Incoming providing high-speed
internet
internet service
cable
Setup > Network, DHCP connection
Ethernet
cable
Note: Manual setup is available only for a wired connection.
1. Connect the TV to your network router with a
Category-5 Ethernet cable (not supplied).
2. In the Setup > Network menu, highlight Manual
and press ENTER.
3. Press to move to the Connection Data area.
4. Input the connection data.
5. After entering connection data, press ENTER to
connect.
6. Change any of the following if needed:
• Default Gateway
• DNS
• Subnet Mask
For assistance call 1(800) 332-2119
44
3. TV Features
StreamTV™ Internet Media, continued
CENTER
INPUT
Wireless Connection
1. Disconnect the Ethernet cable if present.
2. Connect the wireless adapter to the TV’s
3.
USB port as shown for your TV model.
Open the Setup > Network menu. After
a few moments, detected networks will
appear listed on the screen in order of
signal strength.
DIGITAL
AUDIO
OUTPUT
R
AUDIO
OUTPUT
ANT
AUDIO/SURROUND
R OUTPUT L
L
Y/ VIDEO
HDMI
2
1
3
R AUDIO
IEEE 802.11n-compliant
wireless network
router providing
high-speed internet
service
Pb
Pr
LAN
L
Y/ VIDEO
Pb
Pr
(480i / 480p / 720p / 1080i)
INPUT 2
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
3D
GLASSES
EMITTER
INPUT 1
The TV requires an AzureWave AW-NU231 USB
wireless adapter. The adapter is available from
your Mitsubishi dealer.
SUB
WOOFER
OUTPUT
Back of 738
Series TV
Wireless
adapter
OR
Incoming
internet
cable
INPUT 3
Pr
Pb
Y/ VIDEO
L AUDIO R
USB
HDMI 4
838 Series
TV
Wireless
adapter
Setup > Network menu after connecting. The active
network is checked and connection data displays.
Setup > Network menu, manual connection
4. Highlight the desired network and press ENTER to
connect. A check will appear next to the connected
network. Press CH/PAGE to see more networks if the
list fills more than one screen.
5. If connecting to a secure network, enter the
network key or password when prompted. Special
remote control keys you may need:
Key
1
CANCEL
Use for
Digit 1 and special characters
! @ # $ % ^ * _ - + = . space ?
•
•
LAST
Clears the password box of an old
entry from a prior session.
Deletes one character during password entry.
Toggles between upper and lower case
6. Press ENTER to connect.
Note: If you notice interference from the TV’s internal
wireless components, turn off the TV’s transmitter. Open the Setup > Network menu. Select
Off and press ENTER.
To reconnect later, open the Setup > Network
menu, highlight the network, and press ENTER.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
3. TV Features
45
StreamTV™ Internet Media, continued
Using StreamTV Internet Media
1. After establishing internet connectivity as described
2.
3.
Troubleshooting
If You Are Unable to Connect to the Internet
• Check all power and data connections.
• If you can reach the internet with a computer or
other device on the same internet service used by
the TV, consult the router or modem owner’s guide
for reset instructions.
• If you cannot reach the internet, contact your
service provider. You may be asked for network
information such as the TV’s IP address. Go to the
Setup > Network menu to see connection data.
in “Home Network Setup,” page 43, switch the TV to
any input other than Bluetooth® or USB.
Press the INTERNET key to display services from
VUDU Apps.
Highlight an application and press ENTER to launch it.
Getting Started with VUDU Movies
1. After establishing internet connectivity as described
2.
3.
4.
5.
in “Home Network Setup,” page 43, switch the TV to
any input other than Bluetooth® or USB.
Press the INTERNET key to display services from
VUDU Apps.
Highlight the VUDU movie service and press ENTER.
Browse the VUDU movie catalog and offerings.
When you are ready to rent or buy a movie, you
will be prompted to activate your VUDU account.
Follow the on-screen instructions and use a computer to go to www.VUDU.com/activation. A
credit card is required for activation.
For Further Assistance
• If you are having trouble connecting your TV or
accessing internet applications, contact Mitsubishi
Customer Care at 1-800-332-2119.
• If you are having difficulty with your VUDU
account, contact VUDU Customer Care at
www.VUDU.com/support.
• See more troubleshooting tips on page 91.
Once your account is activated, you can rent and buy
movies using only the TV and the TV’s remote control.
Using VUDU Apps and VUDU Movies
TOOLS. Use the Tools menu to perform A/V reset
while in VUDU movies or some VUDU Apps.
Navigate VUDU’s menus with the keys on
the TV’s remote control. Browse the movie
catalog, watch movie previews, set parental
controls, and rent or buy movies.
LAST
• Goes to the previous screen.
• Stops video playback and returns to the previous menu.
CANCEL. Acts like the backspace key during
text entry.
LAST
ENTER
• Selects a menu item.
• Launches an application from the VUDU
Apps menu.
• In VUDU’s movie service, use during
video playback to see options.
•
•
Directional navigation
In VUDU Apps, press
more applications.
to display
GUIDE. In VUDU’s movie service, returns to
the VUDU home menu.
TOOLS
INTERNET
CH/PAGE. Jumps to the previous or next page of
menu items.
INTERNET. Displays the VUDU Apps internet
menu. Switch the TV to any input other than
Bluetooth® or USB before connecting to the internet.
EXIT. Depending on context:
• Closes the internet menu.
• Goes to the VUDU home page.
In VUDU’s movie service:
PLAY/PAUSE
Starts or pauses video playback.
INFO. In VUDU’s movie service, works like
the VUDU MORE key. Displays more options
for the current selection if available.
FAST FORWARD/REVERSE
• Press to search scenes forward or back.
• Press additional times to speed up search.
• Press opposite key to slow and pause search.
F2. Displays the VUDU system menu if available.
STOP
Stops video playback and returns to the previous menu.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
46
3. TV Features
Introduction to Home-Theater Control
This TV offers a choice of home-theater-control systems. This summary offers some examples of the control
methods available using the TV’s remote control. You may wish to use one or more of these methods in your
home theater after completing Auto Input Sensing.
Source device connected directly to the TV
Remote Control Programming (Any Connection Type)
Program the remote control to operate the A/V device. To control the device, set
the remote control to the correct mode for the device type. See Appendix A, page
75. In the case of an A/V receiver, use the Audio Lock feature, page 76.
CEC-Enabled HDMI Device (HDMI Connection Only)
See Appendix C, page 83.
838 Series. NetCommand IR Control (Any Connection Type)
Set up NetCommand IR control of the device’s keys as desired. See “IR Emitters,”
page 63, and “Initial NetCommand Setup,” page 64.
Any Connection Type
A/V
Device
TV
HDMI
Cable
CEC-Enabled
A/V Device
TV
Any Connection Type
A/V
Device
TV
Source device connected to an A/V receiver connected to the TV
CEC-Enabled
Source Device
CEC-Enabled HDMI A/V Receiver
The TV’s remote control may operate some functions of a connected A/V device.
You can switch to the device by selecting its icon in the TV’s Input Selection menu.
See Appendix C, page 83.
HDMI
Cable
A/V Receiver
TV
838 Series: A/V Receiver with HDMI Output (no CEC)
1. Set up NetCommand IR control of the A/V receiver’s keys as desired. See “IR
Emitters,” page 63, and “Setting Up A/V Receiver Control,” page 69.
2. Set up NetCommand IR control of the source device’s keys as desired. See
“NetCommand Control of a Device Connected to an HDMI A/V Receiver,” page
72.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Source
Device
HDMI
Cable
Any Connection Type
A/V Receiver
HDMI
Cable
TV
4
47
TV Menus
Main Menu
Press MENU on the remote control to open the main menu.
Picture
Picture settings.
47
Sound
Sound settings.
51
Captions
Closed captions
on/and off; caption
displays.
53
Setup
Basic TV setup.
54
Inputs
Name assignments for TV
inputs, HDMI Control setup
838 Series. NetCommand
IR “learning.”
57
Lock
Setting a pass code and
restrictions TV use. Disabling the control-panel
buttons.
59
Picture
Assign a name to the TV input before making video adjustments (use the New Device Found or Inputs > Name
menu). Adjustments will be reset to the defaults if you
rename the input after making adjustments.
Picture
Video
Settings in this menu are saved for the current input only.
To make Video adjustments while watching TV and without using the menu:
1. Press the VIDEO key.
2. Press
to select a video option.
3. Press
to change the setting.
Picture
Mode
Brilliant
For use under bright light; unavailable when the
current input is named Game or PC.
Game
Optimizes video processing for gaming consoles.
Available only when the name of the input is Game
or PC.
Bright
For most daytime viewing and x.v.Color sources
Natural
For most nighttime viewing and x.v.Color sources
Advanced
Contact your professional installer for setup or see page 49.
738 series: Special/ADV
838 series: ISF Day/ADV1, ISF Night/ADV2
Downloaded From TV-Manual.com Manuals
Set the Picture Mode first
before changing other video
settings, as some settings are
stored independently for each
Picture Mode. Use Picture
Modes to get the best image
under different viewing conditions.
For assistance call 1(800) 332-2119
48
4. TV Menus
Picture, continued
Contrast
•
•
•
Brightness
Color
Tint
Sharpness
Color Temp
Low contrast shows a variety of shades in darker images
In most home lighting situations, medium contrast looks
best.
High contrast shows darker images more uniformly black
and makes colors appear more vibrant. High contrast is
good for brightly lit environments.
Adjusts the white-to-black level
Settings are stored independently for each Picture Mode.
Adjusts overall picture brightness. Settings are stored independently for each Picture Mode.
Adjusts overall color intensity from monochromatic to fully saturated.
Adjusts the red-to-green ratio.
Adjusts picture detail and clarity.
High
Gives white images a cool cast. May provide the most
realistic picture under bright lighting.
Low
Gives white images a warm cast. Natural/Color
Temp at the low setting displays video at approximately the 6500K industry standard for NTSC
pictures.
High,
Medium,
Low, Off
•
•
•
•
EdgeEnhance
On, Off
EdgeEnhance™ adds special edge enhancements to make the image appear
sharper.
DeepField
Imager
On, Off
DeepField™ Imager dynamically enhances black levels in portions of the screen to
provide strong contrast with detail over mixed screen content.
Demo
For comparison, displays a split picture to show On (right side) and Off (left side).
Video
Noise
Picture
Screensaver
High. For poor-quality signals.
Medium. For moderate noise reduction.
Low. For good-quality signals.
Off. Leaves the picture unaltered.
Adjusts the white balance.
Settings are stored independently for each Picture Mode.
Reduces minor noise (graininess) in the picture.
Picture+ (Picture Plus)
On, Off
Select On to display a screensaver pattern while playing an audio-only input. To use
this feature, the input must either
• Be named as an audio source (e.g., CD, MP3 Player, Bluetooth)
or
• Be the antenna input tuned to an audio-only signal.
Auto, Off
480i and 1080i signals only. In Auto, the TV automatically detects and applies film-decoding correction to movies filmed at 24 frames per second. Try the Off setting if images
show many jagged edges. Setting saved by input.
Smooth 120
On, Off
When active, reduces motion blur in action scenes but may show pixel structure during
slower motion or in still images. Works in conjunction with Film Mode.
Test Picture
Displays a test picture.
Film Mode
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
4. TV Menus
49
Picture, continued
Picture
Reset
•
•
Picture
Resets sound and picture adjustments for the current input. Highlight the Reset icon
and press ENTER twice to perform reset.
Reset has no effect on universal settings (Balance, Listen To, Language) or on
Advanced picture settings.
Perfect
(PerfectColor/PerfecTint, 838 series)
PerfectColor Sliders Adjusts the saturation (intensity) of six colors for the current image source.
PerfecTint Sliders Adjusts six hues for the current image source
Using PerfectColor:
Highlight the Perfect icon and press ENTER to display the PerfectColor menu. Settings are retained independently
for each TV input.
Using PerfecTint:
• To switch between PerfectColor™ and PerfecTint™ adjustments, highlight PerfectColor/PerfecTint and press
.
• Press
to move from one color bar to the next.
• Press
to change settings.
• Press CANCEL to restore default settings.
• Press MENU to return to the main menu.
Picture
Advanced
Picture > Advanced allows you to save highly customized picture adjustments for each input. Mitsubishi recommends these adjustments be
made only by a trained professional installer.
1. Press MENU. Under Picture, highlight the Advanced icon and press ENTER.
2. With Picture Mode (the first option) highlighted, press ENTER to change from blank (undefined) to ADV.
838 Series: Choose ADV1 (daytime settings) or ADV2 (nighttime settings).
3. Use
to highlight an option you wish to change and press ENTER to see the adjustment display.
4. Press
to change settings.
5. Use
to navigate to additional options and press
to change settings.
6. Press MENU to return to the Picture > Advanced menu and save the adjustments for the current input. Press EXIT
to close the menu.
To use the custom Picture Mode at a later time
Press MENU and go to Picture > Video > Picture Mode and:
738 Series
•
•
Select SPECIAL if settings were saved by your
professional installer.
Otherwise select ADV.
Downloaded From TV-Manual.com Manuals
838 Series
•
•
Select ISF Day or ISF Night if settings were saved by
your professional installer.
Otherwise select ADV1 or ADV2.
For assistance call 1(800) 332-2119
50
4. TV Menus
Picture, continued
To return to the default values for Advanced
Display the Picture > Advanced menu and:
738 Series
838 Series
Highlight RESET Pic Mode and press ENTER.
1. Highlight the Advanced mode to change.
2. Highlight RESET Pic Mode and press ENTER. You must
perform the reset separately for both ADV1 and ADV2
Picture
3D
Mode
See page 33 for use of this menu.
3D Mode
Source
Format
Glasses L-R
Glasses
Control
Off, On
Enables or disables 3D mode for the current input.
Checkerboard 3D formats supported by the TV.
Side-by-Side
Standard,
Reverse
Synchronizes left/right images to work with your 3D glasses.
IR Emitter,
DLP Link
Switches between control methods for 3D glasses.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
4. TV Menus
51
Sound
Sound
Audio
Settings in this menu are saved for the current input only with the exception of Balance and Subwoofer, which
apply to all inputs.
To make Audio adjustments while watching TV and without using the menu:
1. Press the AUDIO key.
2. Press
to select an audio option.
3. Press
to change the setting.
TV Speakers
Bass
Treble
Balance
Subwoofer
(838 Series)
Sound Mode
On
Turns on the internal TV speakers.
Off
Turns off the internal TV speakers so you hear sound only from a connected A/V
receiver.
Note: When you disconnect an A/V receiver, be sure to change the TV Speakers
setting to On to hear sound from the TV speakers.
Center
(838 Series)
Makes the TV’s speaker array act as a center channel. See “Using the TV Speakers
as a Center Channel,” page 27.
Notes:
• Set Sound > Global > Center Channel to On to make this setting available.
• To de-activate the center channel, change this setting to On or Off.
Controls volume of low-pitched sound from the TV speakers.
Controls volume of high-pitched sound from the TV speakers.
Controls audio balance between the right and left TV speakers
Adjusts the volume level of a connected subwoofer.
[Subwoofer level
Note: Set Sound > Global > Subwoofer to On to make this adjustment availadjustment]
able.
Stereo
No special audio effects from the TV speakers
Surround
Modifies audio from the TV speakers.
• For monaural (non-stereo) programs, creates a simulated stereo effect.
• For stereo programs, creates a simulated surround sound effect.
• 838 Series. The TV’s speaker array plays 5.1 surround sound if available.
Music
(838 Series)
Optimizes the TV’s speaker array for music listening.
Night
(838 Series)
Focuses the TV’s speaker array to a single point to limit sound heard by others
outside the room. Press ENTER to adjust the focal point (Night Angle).
Level Sound
On, Off
Reduces differences in sound volume between programming segments, such as
the difference between regular broadcast programs and commercial segments.
Listen To
(applies only
to analog
channels from
the ANT input)
Stereo
The TV plays stereo broadcasts in stereo and mono broadcasts in mono. The
word Stereo is displayed when you tune to a channel broadcasting in stereo.
Mono
Reduces background noise. Use when receiving a weak stereo audio signal. All
audio is played as mono.
SAP
Selects an additional monaural sound track not audible during normal TV viewing.
(Second Audio The SAP signal might be related to the program (such as a sound track in a foreign
Program)
language), or it might be unrelated (such as a weather report). If an SAP signal is
broadcast, the letters SAP are displayed when you tune to the channel.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
52
4. TV Menus
Sound, continued
Sound
Global
Settings in this menu apply to all left and right inputs.
Analog Audio
Out
Subwoofer
Center Channel
Sound
These settings affect audio from the AUDIO OUTPUT jacks.
Fixed
Use with an analog A/V receiver. Control volume from the A/V receiver. The
volume of the audio output signal is fixed and is unaffected by the TV’s volume
control.
Variable
Use with headphones. Adjust headphone volume using the TV’s volume controls.
When set to Variable, the audio output signal is adjustable from the TV’s volume
controls.
Rear
838 Series. Sends left and right rear audio to external speakers. Use when
supplementing the TV’s speaker array with external rear speakers. See “External Rear
Speakers,” page 42.
838 Series. Select On to turn on audio to a connected subwoofer. Set to Off if no subwoofer
is connected.
838 Series. On allows the TV’s speakers to complement your external sound system as a
center channel. Set to Off if not in use. See “Using the TV Speakers as a Center Channel,”
page 27.
Auto SP
838 Series. Performs auto calibration of the Sound Projector speaker array. See “Auto
Setup,” page 41.
Sound
SoundPro
838 Series. Lets you set up the Sound Projector speaker array manually. See page 39.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
4. TV Menus
53
Captions
Captions on Digital Channels
The TV can decode captions from the ANT input only.
Broadcasters can send up to six different captioning
selections or can send analog captions for a program
that originated in analog format. A TV station may broadcast only one or two types of captions or none at all.
•
•
Captions on Analog Channels
The TV can decode captions from the ANT input and
the composite VIDEO jacks. Broadcasters can send
either standard closed captions or text service. Standard
closed captions follow the dialogue of the program and
display in a small section of the screen. Text-service closed
captions often contain information such as weather or
news and cover a large portion of the screen.
Captions
•
IMPORTANT
The content of captions is determined by the
broadcaster. If captions show strange characters, misspellings, or odd grammar, it is not
a malfunction of the TV.
Closed-caption signals are not available through
HDMI or component jacks. See the menus for
devices connected to these inputs for closedcaption decoding.
The Captions menu has no effect on captions
displayed in programming received over the
internet.
Services
Service
On if Mute, On, Off
On if Mute: Displays digital closed-caption signal Caption 1 (digital) or CC1
(analog) when audio from the TV speakers is muted. While watching TV,
press MUTE to turn closed captions on/off.
Digital
Caption 1–Caption 6
Caption signals sent by the broadcaster.
Analog
CC 1–CC 4
Text 1–Text 4
•
•
Captions
CC 1–CC 4. Standard closed-caption signals
Text 1–Text 4. Text-service signals
Font
Style
As Broadcast or
choice of font styles
As Broadcast changes settings to those selected by the captions provider,
or, if none, to the TV’s own caption defaults. Use one of the font styles to
give digital captions a custom appearance.
Size
Large, Medium, Small
Large is recommended.
Captions
Font
Color
White, Black, Magenta, etc.
Recommendations for digital captions:
Translucent, Opaque, Flashing, Transparent
•
Background
White, Black, Magenta, etc.
•
Opacity
(Background)
Translucent, Opaque, Flashing, Transparent
Opacity
Downloaded From TV-Manual.com Manuals
A white font on a black translucent background makes an easy-to-read combination.
Use contrasting colors for captions and background.
For assistance call 1(800) 332-2119
54
4. TV Menus
Setup
Setup
Menu
Antenna
Digital
Audio
Setup
Language
English
Spanish
Displays on-screen menus in either English or Spanish.
Selects the current language for a digital program from the ANT input. Each digital program may
include up to seven language choices or there may be no language choice offered.
Clock
Set the TV clock to:
• Use the TV Timer to power on the TV automatically at a preset time
• Receive correct updates to ChannelView listings
Note: When the Daylight Saving Time change occurs, you must open this menu and set the TV’s clock ahead or back.
Time
Date
Time
Zone
Daylight
Savings
Setup
•
•
•
Highlight the Clock icon and press ENTER or to highlight the time. To edit time and date:
• Press ENTER to select the item to change.
• Press
to change values.
• Press
to move to another column.
Eastern, Central, Mountain, Pacific, etc. The correct time zone is required for accurate ChannelView
updates.
Off, On
Timer
Select the setting for your area (required for accurate ChannelView updates).
The Timer tells the TV to power on automatically at a time you set. Use this menu to set a day,
time, input, and channel for the Timer. If the TV is already on at the set time, the TV will automatically change to the designated channel or input.
The TV clock must be set before you can use the Timer feature.
As a reminder that the TV Timer is set, the TV POWER indicator flashes slowly while the TV is powered off.
When the Timer turns on the TV, press any key on the remote control to keep it from turning off after five minutes.
Timer
Day
Time
Device
On, Off
Select On to enable the Timer.
Daily, Mon-Fri, (every) Sunday, (every) Monday, Select the day or days of the week for the Timer to
(every) Tuesday, etc.
turn on the TV.
To set the time for the TV to come on:
1. Highlighted the time and press ENTER.
2. Press
to change values. Press ENTER to confirm entries.
Ant, DVD, VCR, etc.
Select the input you want displayed when the TV comes on. Choose from the defined and enabled
inputs that appear in the Input Selection menu.
Channel If the source is the ANT input, press
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
to select a channel number or press and hold to scroll quickly.
55
4. TV Menus
Setup, continued
Setup
Channel
Ant Air,
Ant Cable
All Channels,
New Only
Scan
You must perform a channel scan to receive digital channels. The scan searches for broadcast channels and adds them to TV memory. To start channel scan:
1. Highlight one of the input selections based on your connection to the ANT input:
• Air when connected to an indoor or outdoor antenna.
• Cable when connected to direct cable (no cable box)
2. Select the scan type.
• Select All Channels for an initial scan or after moving the TV to an new area with a different channel line-up.
• Select New Only to search for channels newly broadcasting since the previous scan.
3. Press to highlight SCAN.
4. Press ENTER to start channel memorization.
See below for additional notes on Scan.
Edit
After channel scan, Edit lets you add and delete memorized channels. Memorized channels are
those you can tune using the CH key. Edit the channel list to limit tuning to channels you watch.
• Press CH/PAGE to jump to the next or previous page of channel numbers.
• Press
to move through all channel numbers, one at a time.
Adding/Deleting Channels Using the Channel Edit
Menu
• Channels marked with a check are in memory.
• To add or delete a channel from memory, highlight
the channel number and press ENTER.
• To add a single digital channel not in the list, see
the notes under Scan on this page.
• Digital channels are listed by virtual channel
number with the physical channel number shown in
small gray text.
-- Virtual Channel Number (digital channels
only). A channel number sent by a local broadcaster.
-- Physical Digital Channel Number. The
channel number officially assigned to the actual
broadcast frequency; shown on screen in gray
text.
Notes on Scan and Channel Memorization
• Channel memorization may take up to 15 minutes to
complete.
• To stop channel memorization before completion, press
CANCEL. Channels already added are retained.
• When watching TV, press CH to move through
memorized channels. Press and hold CH to speed
through channels.
Downloaded From TV-Manual.com Manuals
•
To add a digital channel that does not appear in the
Edit menu without performing channel memorization:
1. Look up the physical channel number for
the new digital channel. See the website
www.antennaweb.org for help.
2. Press INPUT and select the Ant input.
3. Use the number and CANCEL keys to enter the
physical channel number followed by “-1” and
ENTER. For example, for physical channel 36,
3
•
6
1
ENTER.
The TV will search for a digital channel on the channel
36 frequency. When it finds the channel, it will:
a. Add the channel to memory.
b. Change the channel number to the virtual
channel number sent by the broadcaster.
c. Add to memory any associated sub-channels.
Rememorize channels if you move the TV to a different
geographic area with a different channel line-up.
For assistance call 1(800) 332-2119
56
4. TV Menus
Setup, continued
Setup
Lamp
Energy
Blue Glow
(838 series)
Setup
Energy
Standard, Standard is for most viewing conditions. Use Bright in brightly lit rooms. You may
Bright
notice increased fan noise when using the Bright setting.
On, Off
Select On to see blue accent lighting when the TV is powered on.
Network
See “Home Network Setup” on page 43 for use of this menu.
Ethernet Connection DHCP (automatic), Manual
[Connection Data]
Wireless Connection [Network ID]
[Connection Data]
Off. Turns off the radio receiver. Turn off the receiver if there is RF interference with other
devices.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
4. TV Menus
57
Inputs
Inputs
Name
INPUT and HDMI jacks:
Cable box, Cam(corder), CD,
DVD (DVD, DVD2, Blu-ray), DVR,
Game (Game, PS, Xbox, Wii),
Media Box, PC, Satellite, AVR
On/Off (Ant, Bluetooth only)
INPUT jacks only:
CD/Audio, MP3 Player, VCR
HDMI jacks only:
PC, AVR, Delete
•
•
•
•
•
Lets you assign or change names of inputs appearing in the Input Selection menu. Highlight an input and press ENTER multiple times to cycle
through the name choices.
Lets you turn the Ant and Bluetooth inputs On/Off to display or hide them
in the Input Selection menu; highlight the input and press ENTER to switch
between On and Off. A paired device is cleared from memory when the
Bluetooth icon is turned off.
Lets you delete unused HDMI inputs from the Input Selection menu.
A CEC-enabled tuner can be named either Cable Box or Satellite.
A CEC-enabled DVD player can be named DVD, DVD2, or Blu-ray.
General Notes for the Inputs > Name Menu
When you change an input name and then exit the
Name menu:
• The name is changed
• The icon in the Input Selection menu is changed
• Audio and video settings are changed to the
defaults for the new device type.
• 838 Series: All previous NetCommand IR “learning” for the input is erased.
Notes for HDMI devices
• Disconnecting an HDMI device: When you disconnect an HDMI device, the icon remains in the Input
Selection menu until you remove it. Select Delete in
the Inputs > Name menu to remove an unwanted icon
for an HDMI input.
Inputs
•
•
•
If the New Device Found screen does not display
as expected when you connect an HDMI device,
see “Reactivating Auto Input Sensing for an HDMI
Input,” page 13.
HDMI Control and CEC-Enabled Devices: See
Appendix C, “HDMI Control of CEC Devices” on
page 83.
In case of CEC conflicts: Turn off CEC signals in
these ways:
-- Turn off the TV’s HDMI Control signals to the
device (Inputs > HDMI Control menu).
-- Turn off each device’s internal CEC capability.
See Appendix C for the TV’s HDMI Control or, to
turn on/off a specific device’s response to CEC
signals, see the device owner’s manual.
Learn 838 Series. Sets up or changes NetCommand IR control of the current device.
See “About NetCommand IR Control,” page 62.
Inputs
Inputs
AVR
838 Series. Sets up or changes NetCommand IR control of an A/V receiver.
See “NetCommand IR Control of an A/V Receiver” on page 68.
HDMI
Control
On, Off
Downloaded From TV-Manual.com Manuals
Select On or Off to enable or disable the TV’s control of a CEC-enabled
device. See Appendix C, “HDMI Control of CEC Devices” on page 83 for use
of this feature.
For assistance call 1(800) 332-2119
58
4. TV Menus
Inputs, continued
Inputs
Order
Lets you rearrange icons in the Input Selection menu.
1.
2.
3.
4.
Press
to highlight an input icon.
Press ENTER to confirm the selection.
Press
to drag the icon to the desired position.
Press ENTER to confirm the new position.
Inputs
Demo
See demonstrations showcasing selected TV features.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
4. TV Menus
59
Lock
TV Locks
Parental Menu
Parental
Lock by Program Ratings
Restricts access using U.S.-based ratings
sent by broadcasters.
Time
Lock by Time
Restricts TV use by time of day.
Channel
Lock by Channel
Blocks access to the channels you
specify.
Panel
Lock Control Panel
Disables the buttons on the TV’s control
panel. Use this feature if small children
in the home try to press buttons on the
control panel.
Other
Lock by Other Program Ratings
Restricts access using new or non-U.S.based ratings sent by broadcasters.
Pass Code
Setting a Pass Code
You are prompted to enter a pass code whenever you
select Lock on the main menu. To set a pass code for
the first time:
1. Press MENU. Highlight Lock and press ENTER. A
screen prompting you for a pass code will display.
2. Input a four-digit pass code using the number keys
on the remote control.
• Press CANCEL to delete a number and move
back one space.
• Press MENU or EXIT to close the menu without
setting a pass code.
3. Press ENTER to confirm the pass code.
The TV comes from the factory with the rating locks
turned off and with pre-set U.S. ratings TV-PG and
movie rating PG. You must turn on blocking for U.S.
ratings to activate these rating restrictions. Use the
Lock > Parental menu to change the level of blocking
with U.S. ratings.
Any time you change the channel or device, it may take
up to five seconds for the rating restrictions to take effect.
Note: To set parental controls for programs from the
VUDU™ movie service, use the VUDU Info &
Settings menu. The TV’s Parental menu does
not control content accessible through VUDU.
Other Menu (Alternate Rating System)
This TV can recognize new rating systems that may
come into effect in the future. The Other menu allows
you to block digital programming when such systems
come into effect. The Start Time and Stop Time
options in the Parental menu apply to U.S.-based
ratings only and do not affect alternate rating systems.
The first time you tune to a channel broadcasting an
alternate rating system, the TV defaults to the most
restrictive setting if the Lock menu > Other Lock
option is set to On. Use this menu to change the
allowed rating if you are unable to watch a program
rated with an alternate system.
Bypassing TV Locks
•
•
Resetting a Pass Code
See the procedure in Appendix B, page 81.
•
•
•
Downloaded From TV-Manual.com Manuals
If you try to watch a blocked program or channel
or the TV is locked by time, a notice will appear
prompting you for a pass code. To use the TV,
input your four-digit pass code and press ENTER.
-- To reactivate the locks after using a pass code,
power the TV off and then on.
-- To reactivate only the parent ratings lock,
change to a different channel or device.
If a program is blocked, you can still use the TV without
entering a pass code. Change to a channel airing an
allowed program or change to another device.
Important Notes on Rating Locks
Parental menu rating locks apply only to channels and signals received on the ANT and composite VIDEO jacks.
Other menu rating locks apply only to digital channels received on ANT.
When viewing a cable box, satellite receiver,
or other device connected to the component
Y Pb Pr or HDMI inputs, check the device’s
owner’s guide for parental locks.
For assistance call 1(800) 332-2119
60
4. TV Menus
Lock, continued
Lock
Parental
Lock
TV Rating
Movie
Rating
Start Time/
Stop Time
Disables or enables blocking based on V-Chip signals and the U.S. rating system.
Highlight the rating level you wish to
change and press ENTER to block it ( ) or
allow it ( ).
You can apply supplemental content
blocking to the age-based ratings by
using the TV content categories. (FV, D,
L, S, V)
Highlight the rating level you wish to change and press ENTER to block it ( ) or allow it ( ). You
can apply supplemental blocking to the age-based ratings by using the TV content categories below.
Sets the time of day for enforcement of rating restrictions chosen in the Parental menu. To make
rating restrictions active 24 hours a day, make Start Time and Stop Time the same.
1. Highlight the start time or stop time.
2. Press ENTER to start editing.
3. Press
to make changes.
4. Press ENTER to confirm changes.
TV Content Categories
TV Age-Based Ratings
TV Program Ratings
TV-Y
Youth. For children under 7.
TV-Y7
Youth 7 and older.
TV-G
General Audience. For the entire family.
TV-PG
Parental Guidance. Parental Guidance
recommended; may not be suitable for
some children.
TV-14
Adolescent 14 and older. Not recommended
for children under 14.
TV-MA
Mature Audience. For adults only.
FV
Fantasy Violence. Applies to TV-Y7 only.
D
Sexual Dialog. Applies in differing
degrees to TV-PG and TV-14.
L
Adult Language. Applies in differing
degrees to TV-PG, TV-14, and TV-MA.
S
Sexual Situations. Applies in differing
degrees to TV-PG, TV-14, and TV-MA.
V
Violence (graphic or realistic). Applies in differing degrees to TV-PG, TV-14, and TV-MA.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Movie Ratings
G
General Audience. Designed for the
entire family.
PG
Parental Guidance. Parental Guidance
recommended; may not be suitable for
some children.
PG-13
Parental Guidance, 13 and Older.
Not recommended for children under
13.
R
Restricted. Restricted in theaters to 17
years old and older unless accompanied
by an adult.
NC-17
No Children 17 or Under. Restricted
in theaters to 18 years old and older.
X
Adult. Designed for and restricted in
theaters to adult audiences only.
Not
Rated
No MPAA rating assigned
4. TV Menus
61
Lock, continued
Lock
Time
Lock by
Time
Lock Time,
Unlock
Time
Blocks all use of the TV during the time period you specify. You must enter a pass code to
use the TV when the time lock is in effect. After releasing the lock with the pass code, the lock
does not go back into effect until the next time the TV is powered on.
Enables/disables Lock by Time.
To set the lock and unlock times:
1. Highlight the lock or unlock time.
2. Press ENTER to start editing.
3. Press
to make changes.
4. Press
to move to another column.
Note: To make Lock by Time active 24 hours a day, make Start Time and Stop Time the same.
Lock
Channel
Lock
Panel
Off, On
Lock
The Channel Lock menu lists channels currently in memory (see page 55). Highlight a
channel and press ENTER to lock ( ) or allow ( ) the channel. Channels locks will be
cleared the next time you perform a channel scan.
On locks and Off unlocks the buttons on the TV’s control panel. Use this option if small children try
to press TV buttons.
• To release the Panel Lock using the TV’s control panel, press and hold the INPUT button for ten
seconds. If the TV is powered off, press and hold INPUT for ten seconds and then press POWER
to make the TV power on.
• To reactivate the lock, return to this menu and change the setting to On.
Other
Other Menu Options (alternate rating system)
This TV can recognize new rating systems that may come into effect in the future. Such alternate rating systems will apply only to digital programming received on the ANT input.
Lock
On, Off
Enables/disables program blocking.
System
The rating system available for the channel
Group
Rating groups available in the rating system shown on the screen. Rating groups are defined by the
rating system in effect.
Rating
Rating restrictions available in the selected rating system and group. Highlight the rating and press
ENTER to check (block) or uncheck (allow) rated content.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
62
5
NetCommand IR Control
About NetCommand IR Control
•
•
•
•
•
NetCommand IR home-theater control is available on 838 series TVs.
IR emitter cables are available for purchase
from Mitsubishi. Visit www.mitsuparts.com or call
800-553-7278 and request one of the following:
-- 242D483020 (two-ended cable)
-- 299P254020 (four-ended cable).
NetCommand setup is optional.
You can perform NetCommand setup for a device
any time after the TV has detected the device.
NetCommand operates by sending remote control
signals from the TV to your other devices via the
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
•
IR (infrared) emitters, telling the devices to play,
record, change inputs, adjust volume, change channels, or perform other functions. All this is accomplished with the TV’s remote control left in TV mode.
You may wish to use NetCommand IR control to
supplement control of CEC-enabled devices.
Important Note on NetCommand
Be sure to connect the IR emitter cable to the
TV and properly place the emitters so that
NetCommand can control your devices.
*OGSPOUPGBTJOHMF
5. NetCommand
IR Control (838 Series) *3TFOTPS
63
BWFSBHFTJ[FEEFWJDF
IR Emitters
*3TFOTPS
*3TFOTPS
*OGSPOUTIBSFECZUXP
BWFSBHFTJ[FEEFWJDFT
CENTER
INPUT
*3TFOTPS
SUB
WOOFER
OUTPUT
DIGITAL
AUDIO
OUTPUT
IR emitter cables are available for purchase from
Mitsubishi. Request either part number 242D483020
(two-ended
cable) or part number 299P254020 (fourOGSPOUPGB
ended
cable).
OHMFBWFSBHF
AUDIO
OUTPUT
*3TFOTPS
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
R
Y/ VIDEO
HDMI
2
1
3
LAN
R AUDIO
[FEEFWJDF
1. Connect the plug end of the IR emitter cable to the
IR—NetCommand Output jack on the TV back panel.
2. When the New Device Found screen displays,
highlight IR—NetCommand Output.
ANT
DVI/PC AUDIO
R INPUT L
L
Pb
Pr
IR-NetCommand
Output/EXTERNAL
Y/ VIDEO
Pb
Pr
CONTROLLER
(480i / 480p / 720p / 1080i)INPUT
3D
GLASSES
EMITTER
INPUT 1
The NetCommand system uses emitters connected
to the IR–NetCommand Output jack to control other
devices such as DVD players, cable boxes, satellite
receivers, and VCRs.
INPUT 2
6.
Placement
0OUPQPGBTJOHMFUBMM
EFWJDF
Place any unused ends behind the devices to
prevent stray signals from reaching the IR sensors.
L
TV main panel
Other A/V Device
TPS
S
CH
D I G I T A L
SURROUND
A/V Receiver
Connecting IR–NetCommand Output
*OGSPOUPGBTJOHMF
BWFSBHFTJ[FEEFWJDF
The New Device Found screen displays when you
OGSPOUTIBSFE
connect the IR emitter.
CZUXPBWFSBHF
TJ[FEEFWJDFT
3. Highlight EXIT and press ENTER.
4. Position the emitter end with the emitter bulb facing
the device’s remote control sensor. The bulb emits
infrared light in a cone-shaped pattern. Place the
bulb far enough from the sensor to allow the cone
pattern to reach the sensor.
In some cases, the emitter works better facing
downward from the top of the device. Experiment
to find what works best.
5. Secure the emitter ends in place using double-
*3TFOTPS
*3TFOTPS
*OGSPOUTIBSFECZ
UXPBWFSBHFTJ[FE
EFWJDFT
*3TFOTPS
If You are Unable to Locate
a Device’s IR Sensor
•
•
Downloaded From TV-Manual.com Manuals
*3TFOTPS
Place IR emitters so the signal can be “seen” by the IR
sensor on each device.
sided tape.
IMPORTANT
Position IR emitters so that each device’s
sensor “sees” the signal from only one emitter.
Otherwise, a device receiving signals from
multiple sources (remote controls, IR emitters)
may not respond at all.
0OUPQPGBTJOHMF
UBMMEFWJDF
*3TFOTPS
The IR sensor is usually behind the plastic window
of the front display panel. Using a flashlight, you
may be able to see it as a round or square cutout.
If you cannot see the sensor and the device’s
Owner’s Guide does not specify the location, do
the following using the device’s remote control.
1. Starting at one end of the plastic window, hold
the device’s remote control about one-half
inch from the front of the device and press the
POWER key.
2. If the device does not respond, move the
remote control one inch toward the center and
try again. Repeat until the device responds.
3. Repeat the previous steps starting at the other
end of the window. The sensor is between
these two points.
For assistance call 1(800) 332-2119
64
5. NetCommand IR Control (838 Series)
NetCommand Setup
Initial NetCommand Setup
3. Switch the TV to the desired input to control. Press
To perform this procedure, you need:
• The remote controls for both the TV and the
device you want to control.
• An IR emitter cable available from Mitsubishi.
4.
5. The first function highlighted in the Learn screen
Note: To set up an A/V receiver, see “Setting Up A/V
Receiver Control,” page 69.
1. Connect and position the IR emitters for the
2.
INPUT, highlight the input icon, and press ENTER.
Open the NetCommand Inputs > Learn menu.
6.
devices you wish to control. See “IR Emitters” on
the previous page.
Set the TV’s remote control to TV mode and power
on the TV.
NetCommand and Device-Specific Keys
Device-specific keys are those which have no
equivalent on the TV’s remote control. Use any of
these methods to set up NetCommand control for
these keys.
•
is always Power On. Aim the TV’s remote control
at the TV and press ENTER to begin learning for that
function.
When the Power On text starts flashing, aim the
device’s remote control at the TV and hold the POWER
key until a check mark appears next to Power On.
• If the text stops flashing before the check mark
appears, repeat the previous step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
• To verify the device’s response to the IR code,
press ENTER to send out the code.
TOOLS Menu. In some cases, the TV will, by
default, assign a key to the TOOLS menu. See
the table below.
Examples of Default NetCommand
Assignments in the TOOLS Menu
Cable Box, Satellite Receiver
DVD, DVR,
Blu-ray
VCR
A/V Receiver
3
MENU
9
ON DEMAND
3
SETUP
6
TOP MENU
9
ANGLE
3
MENU
6
INPUT
3
MENU
6
SURROUND
NetCommand’s default setup assigns some
device-specific keys to the TOOLS menu when
“learned.” These key functions are accessible only
with the TOOLS key.
•
•
F Keys. There are four F keys, F1 through F4,
which you can assign to any function on the
device’s remote control. For a cable box,
“learn” the F keys as the A, B, C, D keys.
Arbitrary Key Assignment. You can assign a
device key arbitrarily to any “unlearned” key
on the TV’s remote control. Make a note of the
key name and function for later reference.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Inputs > Learn screen. Key names marked with a check
have been “learned.”
Some device-specific keys, such as MENU, are available
only from the TOOLS menu after “learning.”
7. Use navigation keys on the TV’s remote control to
highlight other keys on the list. Repeat steps 5 and
6 for each additional function you wish to control
through NetCommand.
8. If the device has a separate POWER OFF key, use
9.
navigation keys on the TV’s remote to highlight
Power Off. Repeat the earlier steps to “learn” the
POWER OFF key.
If the device has no POWER OFF key, skip this step.
Press EXIT to finish NetCommand “learning” for the
current device.
5. NetCommand IR Control (838 Series)
NetCommand Setup, continued
Adding or Removing Device Keys from
NetCommand Control
After performing initial setup, you can add or remove
individual keys under NetCommand control.
1. Switch the TV to the device. Press INPUT, highlight
the device’s icon, and press ENTER.
2. Open the Inputs menu and highlight the Learn icon.
3. When the Learn screen displays:
• To add keys: Continue as described earlier
under “Initial NetCommand Setup” on the
opposite page.
• To delete keys: Highlight the name of the key
you wish to delete and press CANCEL on the
TV‘s remote control. Clears the check mark.
65
Operating NetCommand-Controlled
Devices
Controlling Most Device Types
As an example of NetCommand control, if you are
watching your cable box and you wish to tune to the
next channel higher, press CHANNEL Up. NetCommand
then sends the “learned” channel-up control signal to
the cable box.
1. Perform NetCommand setup for the device as
2.
3.
4.
described in this chapter.
When you wish to use the device, press INPUT.
Highlight the icon for the device.
Press ENTER to switch the TV to the device.
Note: if you have set up automatic input switching for
the A/V receiver, the A/V receiver will automatically switch to the correct input for the device.
5. To operate the device using the TV’s remote
control, press the TV key to put the remote control
into TV mode.
6. Point the remote control at the TV (not the device)
and press the key for the desired function.
7. Press the TOOLS key to access additional key functions you may have “learned” for the device.
Special Operation Methods
Key Name in
Learning Screen
Special Operation Description and Setup
How to Use
Power On
Manual Power On/Off
Use for devices that have only one POWER key.
1. Press INPUT.
2. Highlight the icon for the device to be
powered on or off.
3. With the Input Selection menu still displayed, press POWER to send the power
signal; you may need to press POWER twice.
Note: If you press POWER without the Input Selection menu displayed, the TV will turn
off.
4. Press ENTER to switch the TV to the device.
Power On
Power Off
Automatic Power On/Off
This feature is only for devices that have separate
Power On and Power Off keys on their original
remote controls. If your device does not have a
separate Power Off key, do not use the Power
Off learning position; use only the Manual Power
ON/OFF method described above.
In the NetCommand Learn screen:
a. “Learn” the Power On command in the
Power On learning position.
b. “Learn” the Power Off command in the
Power Off learning position.
Downloaded From TV-Manual.com Manuals
•
To Power On the Device
1. Press INPUT.
2. Highlight the icon for the device to be
powered on or off.
3. Press ENTER to switch the TV to the
device and NetCommand will send the
Power On command to the device.
•
To Power Off the Device
When you turn the TV off, the TV sends all
learned Power Off commands to all devices.
For assistance call 1(800) 332-2119
66
5. NetCommand IR Control (838 Series)
Operating NetCommand-Controlled Devices, continued
Key Name in
Learning Screen
Special Operation Description and Setup
How to Use
Menu
Displaying a Menu for the Current Device
Press TOOLS and number 3 to send the menu
signal to the device.
“Learn” the MENU key on the original remote in the
Menu learning position.
Guide
Displaying the On-Screen Program Guide
(cable box or satellite receiver)
1. While watching the device, press GUIDE to
display the guide.
1. “Learn” the Guide key on the original remote in 2. Press CH/PAGE to send the Page Up/Dn commands for the guide.
the Guide learning position.
2. Learn the PAGE UP and PAGE DOWN keys of the
original remote in the Page Up and Page
Down learning positions.
Enter
ENTER-Key Functions (cable boxes, satellite receivers, etc.)
Some devices have two keys that have “enter” functions. One key is for menus and is often labelled
SELECT or OK. A second key is for use with number keys for direct channel selection. NetCommand
uses the same ENTER key for both operations.
When ENTER has a menu or guide function or
when the original remote control uses the same
key for menus and channel selection:
Learn the ENTER, SELECT, or OK key in the
NetCommand Enter learning position.
Enter (digits) When ENTER is for channel changes, i.e., the original remote control has a separate ENTER key for
this function):
1. Press MENU or GUIDE to display the device’s
menu or guide.
2. Press ENTER within the menu and
NetCommand will send the Enter signal for
menus.
Press digit key(s) and then press ENTER.
NetCommand will send the Enter signal for
channel selection.
Learn the ENTER key for channel selection in
the NetCommand Enter (digits) learning position. Use this learning position only if the original
remote control has separate keys for Enter in
menus and Enter for channel selection.
Cancel
CANCEL as the Cancel or Exit Function
“Learn” the Cancel or Exit function in the
NetCommand Cancel learning position
—
(separator)
The symbol “—” can serve as the separator
Press digit key(s) and press CANCEL.
between a digital channel’s main and sub-channel NetCommand will send the channel-separator
digits, e.g., digital channel 12-1 (main channel is
signal.
12, sub-channel is 1).
“Learn” the channel separator function in the
NetCommand – (separator) learning position.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
1. Press MENU or GUIDE to display the menu or
guide.
2. Press CANCEL and NetCommand will send
the Cancel or Exit signal.
67
5. NetCommand IR Control (838 Series)
Operating NetCommand-Controlled Devices, continued
NetCommand Specialized Device Keys
Refer to this chart when “learning” device keys. See page 65 for
more on keys marked in the “Special Operation Method” column.
Name on TV
Remote
Control
Key Name in
Learning Screen
Function
Power On
Power On or Power ON/OFF (toggle)
Guide
On-Screen Program Guide or DVD Disc Menus
Channel +/Skip +
Next Channel Higher/Skip Forward (Disc)
Channel –/Skip –
Next Channel Lower/Skip Backward (Disc)
Page Up
Page Up in Guides
Page Dn
Page Down in Guides
Last
Last Channel Recall
LAST
Fav
Favorites
FAV
Menu/Top Menu
Menu
TOOLS
Up, Down, Left, Right
Arrow up, arrow down, arrow left, arrow right
,
Enter
Enter or Select (menus)
Cancel
Cancel or exit (menus)
Info
On-screen status display or information display
Play
Start playback
Stop
Stop playback
Forward
Fast Forward
Rewind
Rewind/Fast Reverse
Pause
Pause playback
Record
Start Recording
See Special Operation Method
Table

GUIDE
,

Use TOOLS menu.
,
ENTER


INFO
1, 2, 3, 4, 5, 6, 7, 8, 9, 0 Digits
Two keypresses
Digits 0–9
Enter (digits)
Use after entering digits to tune to a channel by number
- (separator)
Adds channel separator between digital main and sub-channel
numbers
On Demand
On Demand (Cable/Satellite)
TOOLS
Use TOOLS menu.
Setup
Setup (DVD player)
TOOLS
Use TOOLS menu.
Angle
Angle (DVD player)
TOOLS
Use TOOLS menu.
Input
VCR
TOOLS
Use TOOLS menu.
List
List (Cable/Satellite)
TOOLS
Use TOOLS menu.
Surround
Surround (A/V Receiver)
TOOLS
Use TOOLS menu.
Assign your
choice of
device-specific
functions.
F1
F2
F3
F4
Power Off
Power Off
Downloaded From TV-Manual.com Manuals
ENTER


F1
F2
F3
F4

For assistance call 1(800) 332-2119
68
6
NetCommand IR Control of an A/V
Receiver
NetCommand IR home-theater control is available on 838 series TVs. See the description of
NetCommand on “About NetCommand IR Control,”
page 62.
Two levels of NetCommand A/V receiver control are
available through the Inputs > AVR menu.
• Power and volume. See the opposite page.
• Automatic audio and video switching over
HDMI. See “Setup to Control Automatic Audio and
Video Switching via HDMI,” page 71.
Note: To set up control of other device types, see
“Initial NetCommand Setup,” page 64.
Controlling an A/V Receiver
after NetCommand Setup
Switching Audio to and from the A/V
Receiver
1. Press AUDIO.
2. Press to show the TV Speakers option.
3. Press to select either On (sound through TV
speakers) or Off (sound through A/V receiver).
Controlling A/V Receiver Power
Set up NetCommand control of the A/V receiver’s
POWER key or keys to enable these methods.
With Any Connection Type
1.
2.
3.
4.
Press AUDIO.
Press
to show the TV Speakers option.
Press to select Off.
While the audio display is still on screen, point the
remote control at the TV (not the A/V receiver) and
press POWER to power the A/V receiver on or off.
With an HDMI Connection
1. Press INPUT.
2. Highlight the A/V receiver icon.
3. Press POWER.
Controlling Other A/V Receiver Functions
•
•
•
With the A/V receiver powered on and selected, the
TV’s remote control operates the volume and mute
functions.
If you have performed setup to control A/V receiver
switching over HDMI, when you switch to a device
in the Input Selection menu, the A/V receiver will
automatically switch to the correct audio input for
the device.
Press the TOOLS key for functions that may be available only form the Tools menu.
Note: Connect the HDMI cable between the TV
and A/V receiver first before performing
NetCommand setup for the A/V receiver. If you
perform NetCommand setup and then later connect the cable, the NetCommand setup will be
lost.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
6. NetCommand Control of an A/V Receiver (838 Series)
69
Setting Up A/V Receiver Control
Power and Volume
3. When the Power text starts flashing, aim the A/V
receiver’s remote control at the TV and hold the
POWER or POWER ON key until a check mark appears
next to Power.
• If the text stops flashing before the check mark
appears, repeat this step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
Perform this setup to control A/V receiver power and
volume with the TV’s remote control.
To perform this setup you need:
• The remote controls for both the TV and the
A/V receiver.
• An IR emitter cable available from Mitsubishi.
Before You Begin
1. Connect your A/V receiver to the TV and any addi2.
3.
tional devices.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitters,” page 63.
Set the TV’s remote control to TV mode.
4. Press the
5.
Setup to Control A/V Receiver Power and Volume
1. Open the Inputs > AVR menu.
2. The first function highlighted in the AVR screen is
always Power. Aim the TV’s remote control at the
TV and press ENTER to begin learning for Power.
6.
key on the TV’s remote control to highlight
other keys in the list. Repeat steps 2 and 3 for each
additional function you wish to control through NetCommand.
If the A/V receiver has a separate POWER OFF key,
press on the TV’s remote to highlight Power
Off. Repeat steps 2 and 3 to “learn” the POWER OFF
key. If the device has no POWER OFF key, skip this
step.
When finished “learning” the power and volume
keys, press EXIT to watch TV or continue
NetCommand setup if using an HDMI connection.
See “Automatic Audio/Video Switching Over an
HDMI Connection” on the next page
Inputs > AVR screen. Perform
NetCommand IR “learning” for A/V
receiver power and volume keys.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
70
6. NetCommand Control of an A/V Receiver (838 Series)
Setting Up A/V Receiver Control, continued
Automatic Audio/Video Switching Over an
HDMI Connection
If your A/V receiver has an HDMI output, it may be
convenient to send video to the TV over a single HDMI
cable through the A/V receiver. The following setup
enables the A/V receiver to switch automatically to the
correct input when you select a device in the TV’s Input
Selection menu. Depending on the capabilities of the
A/V receiver, the connected source devices can be
analog, digital, or a mixture or the two.
HDMI
Cable
Connections of
any type
TV
Blu-ray player
HDMI
Output
Cable box
DVD player
VCR
A/V Receiver
Use NetCommand to switch an A/V receiver
automatically to the correct audio and video inputs for
a device (available only with an HDMI output to the TV
as shown).
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
More About Using an HDMI Connection
• Audio from devices connected directly to the
TV can be heard from the TV speakers only.
To send audio to the A/V receiver from such
devices, use one of the optional audio connections shown in the diagram on the opposite page. For example, use an optional audio
connection if you wish to use the A/V receiver
speakers to hear audio from:
-- The ANT input
-- A game or camcorder connected directly
to the TV.
• To use NetCommand to supplement HDMI
control of a CEC-enabled A/V receiver, the
recommended setup sequence is:
1. Connect the HDMI cable.
2. Enable HDMI control (New Device Found
screen).
3. Connect the secondary digital audio
cable, if desired.
4. Perform NetCommand setup.
If you perform A/V receiver NetCommand
setup first and then later connect an HDMI
cable, the NetCommand setup will be lost.
•
In some cases, audio from a device connected
to the A/V receiver may not be passed over the
HDMI cable to the TV speakers. In these cases
you must use the A/V receiver speakers to hear
audio.
6. NetCommand Control of an A/V Receiver (838 Series)
71
Setting Up A/V Receiver Control, continued
Before You Begin
To complete these steps you will need:
• The remote controls for both the TV and the
A/V receiver.
• An IR emitter cable available from Mitsubishi.
• An HDMI-to-HDMI cable to connect the A/V
receiver to the TV and cables necessary to
connect devices to the A/V receiver.
4.
5.
1. Connect the A/V receiver to the TV with an HDMI-
DIGITAL
AUDIO
OUTPUT
DVI/PC AUDIO
R INPUT L
R
Y/ VIDEO
HDMI
1
2
Pb
Pr
R AUDIO
L
Y/ VIDEO
3D
AUDIO
R GLASSES
EMITTER
OUTPUT
Pb
Pr
(480i / 480p / 720p / 1080i)
1. Set the TV’s remote control to TV mode.
2. Navigate to the Inputs > AVR menu.
ANT
L
DIGITAL
AUDIO
OUTPUT
LAN
3
AUDIO
OUTPUT
INPUT 2
3.
Setup to Control Automatic Audio
and Video Switching via HDMI
When this setup is complete, the “learned” A/V receiver
input will appear in the TV’s Input Selection menu as a
selectable input.
L
INPUT 1
2.
to-HDMI cable. Do not connect the optional audio
cable at this time.
If desired, enable HDMI Control of a CEC-enabled
A/V receiver. See Appendix C, “HDMI Control of
CEC Devices” on page 83.
Connect your audio/video devices to the A/V
receiver. Note the name of the device connected
to each A/V receiver input. This information will be
needed later to set up NetCommand’s automatic
input switching.
If using an optional audio cable between the TV
and A/V receiver, connect it. Set up NetCommand
control of the A/V receiver’s TV audio input when
setting up automatic switching in the next procedure.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitters,” page 63.
TV
Optional
analog or
digital audio
connection
HDMI cable
To set up A/V switching over HDMI, choose your A/V
receiver input from a list.
3. In the Inputs > AVR menu, highlight the name of the
A/V receiver with
HDMI output
HDMI OUT
DIGITAL
AUDIO IN
R
L
ANALOG AUDIO IN
4.
5.
6.
Any connection
types
High-definition
DVD player
VCR
DVD player
Cable box
A/V receiver input to control. In this example, it is
the DVD input.
Press ENTER on the TV’s remote control.
While the text DVD is flashing, press and hold the
DVD INPUT key on the A/V receiver’s remote control.
When a check appears next to DVD, release the
DVD INPUT key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press
CANCEL while the name is highlighted.
7. If using an optional audio cable between the TV and
A/V receiver, “learn” the TV AUDIO OUT key to enable
automatic switching of audio from sources connected to the TV only.
If there are no more devices to set up, highlight
EXIT and press ENTER or continue to set up additional A/V receiver audio/video sources.
Y/ VIDEO
Multiple video inputs through a single HDMI cable. The
optional audio connection allows you to hear, through the
A/V receiver, devices connected to the TV only, e.g., an
antenna on the ANT input.
Downloaded From TV-Manual.com Manuals
8.
For assistance call 1(800) 332-2119
72
6. NetCommand Control of an A/V Receiver (838 Series)
Setting Up A/V Receiver Control, continued
NetCommand Control of a Device Connected to an HDMI A/V Receiver
Use this setup to have NetCommand control a device
sending audio and video through the A/V receiver to the
TV via HDMI.
You must have already completed the procedure under
“Setup to Control Automatic Audio and Video Switching via HDMI” on the previous page. That procedure
placed an icon in the Input Selection menu for the
device (input) connected to the A/V receiver.
Any Connection
Type
Source
Device
A/V
Receiver
Downloaded From TV-Manual.com Manuals
HDMI
Cable
TV
For assistance call 1(800) 332-2119
1. Set up NetCommand control of A/V receiver audio/
2.
3.
4.
5.
6.
7.
video switching via HDMI as described on the previous page.
Press EXIT to close any open menus and return to
normal TV viewing.
Press INPUT.
Highlight the icon for the device connected to the
A/V receiver input you wish to control.
Press ENTER to switch the TV to the A/V receiver
and the A/V receiver to the input.
Open the Inputs > Learn menu.
Perform NetCommand “learning” for the connected device by following the steps in “Initial
NetCommand Setup,” page 64.
73
Appendices
Appendix A: Programming the Remote Control. . . . . . . . . . . .
75
Appendix B: Bypassing the Parental Lock. . . . . . . . . . . . . . .
81
Appendix C: HDMI Control of CEC Devices.. . . . . . . . . . . . . .
83
Appendix D: TV Care. . . . . . . . . . . . . . . . . . . . . . . . . . . .
86
Appendix E: Troubleshooting. . . . . . . . . . . . . . . . . . . . . . .
89
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Downloaded From TV-Manual.com Manuals
75
Appendices
Appendix A: Programming the Remote Control
This appendix explains programming the TV’s remote
control to operate other A/V devices. This is distinct
from NetCommand or HDMI CEC.
Functions Available for Other A/V Devices
The TV’s remote control can be programmed to operate
other types and brands of A/V products. The functions performed in each device mode vary depending
on the product. Not all functions work for all models.
The most common functions available are listed on this
page.
VCRs and DVRs
•
•
•
•
•
•
CHANNEL UP/DN
POWER
SLEEP
(FAST Forward)
(Pause)
(Play)
•
•
•
•
•
•
(Record)
(Reverse)
(Stop)
GUIDE (DVR only)
MENU (DVR only)
0–9 Number Buttons
Mitsubishi VCRs are compatible with some additional keys.
Cable Boxes and Satellite Receivers
(not all functions for all models)
TV
CAB/SAT
AUDIO
DVD
VCR
TV
CAB/SAT
AUDIO
DVD
VCR
Control modes
To use the remote after
programming, press the mode
key to match the control mode
to the device type.
•
•
•
•
•
•
•
•
•
•
PAGE UP/DOWN
Cancel
CHANNEL UP/DN
ENTER
GUIDE
POWER
LAST (ENTER; for channels on some models)
0–9 Number Keys
F1–F4 (A, B, C, D keys
on some models)
The record/playback
keys:
•
(FAST Forward)
•
(Pause)
•
(Play)
•
(Record)
•
(Reverse)
•
(Stop)
A/V Receivers
•
•
•
•
•
MUTE
POWER
SLEEP
VOLUME
0–9 Number Buttons
•
Direct Input Selection
buttons: numbers
and LAST (on some
Mitsubishi models)
CD Players
(not all functions for all models)
•
•
•
•
SLEEP
(FAST Forward)
(Pause)
(Play)
•
•
•
(Reverse)
(Stop)
0–9 Number Buttons
DVD Players
(not all functions for all models)
•
•
IMPORTANT
Some manufacturers may change their
products or they may use more than one
remote control system. The TV’s remote
control may be unable to operate your A/V
equipment in these cases.
Downloaded From TV-Manual.com Manuals
•
•
•
•
•
CANCEL (on some
models)
CHANNEL UP/DN (for
track skip on some
models)
ENTER
MENU
POWER
SLEEP
•
•
•
•
•
•
•
(FAST Forward)
(Pause)
(Play)
(Record)
(Reverse)
(Stop)
0-9 Number Keys
For assistance call 1(800) 332-2119
76
Appendices
Appendix A: Programming the Remote Control, continued
Programming the Remote Control
1. Press one of the upper buttons on the remote
control to change to the correct mode for the
product you want to control. Refer to the table
below. Only one of each device type can be controlled in each mode.
IMPORTANT
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
Code Verification
Mode
Affected Device
To determine the code programmed for any mode:
Cab/SAT
Cable Box
DTV Receiver
Satellite Receiver
1. Set the mode to the one you wish to verify.
2. Press and hold POWER on the remote control for
VCR
VCR
DVR
DVD Player/Recorder
DVD
3.
4.
DVD Player/Recorder
DVR
VCR
Audio
5.
A/V Receiver
Audio Amplifier
CD Player
several seconds until the key flashes twice and goes
off.
Press keys 9 9 0
Press 1 and count the flashes of the power key.
Write down the number of flashes as the first digit
of the code.
Repeat step 4 for the other digits of the code.
Press 2 to see flashes for the second digit, press 3
for the third digit, 4 for the fourth digit, and 5 for the
fifth digit.
2. Press and hold POWER on the remote control for
3.
4.
5.
6.
several seconds until the key flashes twice and
goes off.
Release the POWER key.
Enter the first five-digit code listed for your equipment in the reference tables that follow.
If you need to start over or wish to exit
programming mode, temporarily change to a
different device mode.
Point the remote control at the equipment and
press POWER. If the product has no power on/off
function, press a different key, such as
(Play),
(Stop), VOLUME UP, or MUTE.
• If the equipment responds, the remote control
is properly programmed.
• If the equipment does not respond, repeat
steps 4 and 5 with the next five-digit code
listed for your equipment.
Once you have found the correct code, write it in
the space below for future reference.
Mode
Device Type
Code
CABLE/SAT
VCR
DVD
AUDIO
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Audio Lock: Universal A/V Receiver
Control
With Audio Lock enabled, the remote control operates volume and mute on an A/V receiver in all control
modes. Activate Audio Lock if you always use an A/V
receiver with your TV and other A/V equipment.
1. Program AUDIO mode for your A/V receiver as
2.
3.
described in “Programming the Remote Control” on
this page.
With the remote control in AUDIO mode, hold POWER
on the remote control for several seconds until the
key flashes twice and goes off.
Press keys 9 9 3 ENTER
The POWER key will flash twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
1. Press and hold POWER for several seconds until it
2.
flashes twice and goes off.
Press keys 9 9 3 VOLUME UP.
The POWER key will flash four times to indicate Audio
Lock has cleared.
77
Appendices
Appendix A: Programming the Remote Control, continued
Audio Amplifiers
Altec
41742
Lansing
Anthem
42220
Bel Canto
41583
Design
Cary Audio
41879
Design
Classe
41461
Denon
42134
Durabrand
41561
Flextronics
41879
Halcro
41934
Harman/
40892
Kardon
Krell
42463, 41837
Left Coast
40892
Lenoxx
41561
Lexicon
41802, 41145
Marantz
42138, 40892
Mark
42405, 41483
Levinson
Parasound
42245, 41934
Philips
40892
Polk Audio
42242, 40892
Cable Boxes
Amino
Bright House
Cable One
Cablevision
Charter
Cisco
Comcast
Cox
Digeo
Director
General
Instrument
Homecast
i3 Micro
Insight
Jerrold
Knology
Mediacom
Motorola
Myrio
Pace
Panasonic
Pioneer
RCN
11822, 11602
11877, 11376
11877, 11376
11877, 11376
12187, 11877, 11376
11982, 11877, 10877
12576, 11982, 11877,
11376
11877, 11376
12187, 11187
10476
10476
12301
11602
11877, 11376
10476
11877
11877, 11376
11376, 11187, 10476
11822, 11602
11982, 11877, 11376
11982
11877, 10877
11376
Downloaded From TV-Manual.com Manuals
Cable Boxes
Rogers
Scientific
Atlanta
Sejin
Shaw
Sony
Suddenlink
Time Warner
Tivo
CD Players
Burmester
California
Audio Labs
DKK
Garrard
Harman/
Kardon
Integra
JVC
Kenwood
KLH
Koss
LG
Magnavox
Marantz
McIntosh
MCS
MGA
Miro
Mitsubishi
MTC
NAD
Onkyo
Optimus
Panasonic
Parasound
Philips
Pioneer
Proceed
Quasar
RCA
Realistic
Rotel
Sherwood
Sony
Tascam
TDK
Teac
Technics
11877
11877, 10877
11602
11376
11006
11877, 11376
12187, 11877, 11376
12576
40420
40029
40000
40420
41202, 40173, 40083
40101
41294, 40072
40626, 40028
41318
41317
41208
40038
40626, 40038, 40029
41703
40029
40083
40000
40098, 40083
40420
41208
41327, 40101
40420, 40000
40752, 40388, 40029
40420
40626
41087
40420
40029
40420, 40053
40420
40420
41950
41364, 40490, 40185,
40100, 40000
40420
41208
40420
40029
CD Players
Victor
Wards
Yamaha
40072
40053
41292, 40490, 40036
Audio Accessories
Apple
41115
Denon
42502
Vizio
42454
Yamaha
42458
Video Accessories
ADB
12586, 12254
Amino
12482, 11673, 11615,
11481
AT&T
10858
Cisco
12517, 12345
KoolConnect 11481
Motorola
12378, 10858
Scientific
12517, 12345, 10858
Atlanta
SureWest
11481
Verizon
12378
A/V Receivers
Aiwa
41641, 41405, 41388
Alco
41390
AMC
41077
Anam
41609
Arcam
41189
Audiotronic 41189
Audiovox
41390
B&K
40820
Bose
41933, 41841, 41629,
41253, 41229, 40639
Carver
41189
Denon
42857, 42279
Electrohome 42026
Harman/
42443, 42241, 41306,
Kardon
41304, 40891
iLive
42013
Insignia
42175, 42169, 41893,
41077, 41030
Integra
41805, 41320, 41298
iSymphony
42258, 42018
JBL
41306
JVC
42331, 42239, 42040,
41495, 41374
Kenwood
41570, 41569, 41313
KLH
41428, 41412, 41390
LG
42284, 42197, 41293
Magnavox
41514, 41269, 41189
For assistance call 1(800) 332-2119
78
Appendices
Appendix A: Programming the Remote Control, continued
A/V Receivers
Marantz
42114, 41289, 41269,
41189
McIntosh
41289
Micromega 41189
Mitsubishi
41957, 41922, 41921,
41920, 41393
Myryad
41189
Nakamichi
41313
Onkyo
41805, 41531, 41320,
41298, 40842
Optimus
41023
Panasonic
41763, 41633, 41548,
41518, 41316, 41308,
41288, 41275, 42967,
42452, 42221, 41764
Philips
42470, 42459, 42311,
41269, 41266, 41189,
40891
Pioneer
41935, 41384, 41023,
40630
Polk Audio
42270, 41289
Proscan
41254
RCA
42041, 41609, 41511,
41390, 41254, 41023
Samsung
41868, 41500, 41304,
41295
Sherwood
42169, 41905, 41653,
41077
Sherwood
42169
Newcastle
Sony
41759, 41758, 41658,
41622, 41558, 41441,
41258, 41058, 42522,
42216, 42172, 41858,
41822
Stereophonics 41023
Sunfire
41313
Teac
41390
Technics
41518, 41308
Thorens
41189
Toshiba
41788
Venturer
41390
Yamaha
41476, 41376, 41375,
41331, 41276, 41176,
40376, 40176, 42471,
42467, 42061, 41815
Zenith
41293
Satellite Receivers
Bell
10775
ExpressVu
Crossdigital 11109
Downloaded From TV-Manual.com Manuals
Satellite Receivers
DirecTV
11749, 11377, 11142,
10749, 10639, 10566,
10392, 10247, 1856,
11609, 11442, 11414,
11109, 11076
Dish
11775, 11505, 10775
Network
System
Dishpro
11775, 11505, 10775
Echostar
11775, 11505, 10775
Expressvu
11775, 10775
GE
10566
General
10869
Instrument
GOI
11775, 10775
HTS
11775, 10775
Hughes
11749, 11442, 11142,
Network
10749
Systems
Jerrold
10869
JVC
11775, 10775
LG
11414
Mitsubishi
10749
Motorola
10869
Next Level
10869
Panasonic
10701, 10247
Philips
11749, 11442, 11142,
11076, 10749
Proscan
10566, 10392
RadioShack 10869
RCA
10566, 10392, 10143
Samsung
11609, 11442, 11377,
11276, 11109
Sony
10639
Star Choice 10869
Tivo
11442, 11142
Toshiba
11749, 10790, 10749
Voom
10869
Zenith
11856
VCRs
ABS
Accurian
Admiral
Adventura
Aiko
Aiwa
Alienware
Allegro
America
Action
American
High
For assistance call 1(800) 332-2119
21972
20000
20048
20000
20278
20037, 20000
21972
20039
20278
20035
VCRs
Audiovox
Calix
Canon
Carver
CCE
Citizen
Craig
Crosley
Curtis
Mathes
CyberPower
Daewoo
Dell
Denon
DirecTV
Durabrand
Dynatech
Electrohome
Electrophonic
Emerex
Emerson
Fuji
Funai
Garrard
Gateway
GE
GFM
Go Video
GoldStar
Gradiente
Harley
Davidson
Harman/
Kardon
Headquarter
Hewlett
Packard
Hitachi
Howard
Computers
HP
Hughes
Network
Systems
Humax
Hush
iBUYPOWER
Instant
Replay
JVC
KEC
Kenwood
20278, 20037
20037
20035
20081
20278
20278, 20037
20037
20081, 20000
20278, 20162, 20060,
20035
21972
20278, 20045
21972
20042
20739
20039, 20038
20000
20043, 20037
20037
20032
21593, 20593, 20278,
20043, 20037, 20000
20035, 20033
21593, 20593, 20000
20000
21972
20060, 20035
21593
20614
20038, 20037
20000
20000
20081, 20038
20046
21972
20042, 20000
21972
21972
20739, 20042
20739
21972
21972
20035
20067
20278, 20037
20067, 20038
79
Appendices
Appendix A: Programming the Remote Control, continued
VCRs
Kodak
Linksys
Lloyd’s
LXI
Magnasonic
Magnavox
Marantz
Marta
Matsushita
Media
Center PC
MEI
Memorex
MGA
Microsoft
Mind
Minolta
Mitsubishi
Motorola
MTC
Multitech
NEC
Nikko
Niveus
Media
Northgate
Olympus
Optimus
Panasonic
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Polk Audio
Portland
Presidian
Proscan
Pulsar
Quarter
Quartz
Quasar
RadioShack
Radix
Randex
20037, 20035
21972
20000
20037
20593
21593, 20593, 20081,
20039, 20035, 20000
20081, 20035
20037
20162, 20035
21972
20035
20162, 20048, 20046,
20039, 20037, 20035,
20000
20043
21972
21972
20042
20173, 20067, 20043
20048, 20035
20000
20000
20067, 20038
20037
21972
21972
20035
21062, 20593, 20162,
20048, 20037
21062, 20616, 20614,
20162, 20035
20042, 20038, 20037,
20035
20042
20035
21181, 21081, 20739,
20618, 20081, 20035
20037
20067
20081
20278
21593
20060
20039
20046
20046
20162, 20035
20000
20037
20037
Downloaded From TV-Manual.com Manuals
VCRs
RCA
Realistic
ReplayTV
Ricavision
Runco
Samsung
Sanky
Sansui
Sanyo
Scott
Sears
Sharp
Sonic Blue
Sony
Stack 9
STS
Sylvania
Symphonic
Systemax
Tagar
Systems
Tashiko
Teac
Technics
Teknika
Thomas
Tivo
Toshiba
Totevision
Touch
Vector
Vector
Research
Video Concepts
Videomagic
Viewsonic
Villain
Voodoo
Wards
XR-1000
Yamaha
Zenith
ZT Group
20880, 20060, 20042
20048, 20046, 20037,
20035, 20000
20616, 20614
21972
20039
20739, 20045
20048, 20039
20067, 20000
20046
20045, 20043
20046, 20042, 20037,
20035, 20000
20848, 20048
20616, 20614
21972, 21032, 20636,
20035, 20033, 20032,
20000
21972
20042
21593, 20593, 20081,
20043, 20035, 20000
21593, 20593, 20000
21972
21972
20037
20000
20162, 20035
20037, 20035, 20000
20000
20739, 20636, 20618
21972, 21008, 20045,
20043
20037
21972
20045
20038
20045
20037
21972
20000
21972
20081, 20060, 20048,
20042, 20035, 20000
20035, 20000
20038
21139, 20039, 20037,
20033, 20000
21972
DVD Players
Accurian
Adcom
Aiwa
Akai
Alco
Allegro
Apex Digital
Arrgo
Astar
Audiovox
B&K
BBK
Bel Canto
Design
Blue Parade
Broksonic
California
Audio Labs
Cinea
CineVision
Citizen
Coby
Craig
Curtis
Mathes
CyberHome
30675
31094
30641
31089, 30770, 30695
30790
30869
31061, 31056, 31020,
31004, 30797, 30796,
30794, 30755, 30672
31023
31489
31041, 30790
30662
31224
31571
30571
30695
30490
30831
30869, 30833
32116, 31587, 31277,
30695
31628, 31351, 31177,
31165, 31107, 31086,
30852, 30778
30831
31087
31537, 31502, 31129,
31024, 31023, 30874,
30816
Daewoo
31172, 31169, 30869,
30833, 30784
Denon
32258, 30634, 30490
Disney
31270, 30675
Durabrand
31127, 31023
DVD2000
30521
Electrohome 32116
Emerson
30675, 30591
Enterprise
30591
Fisher
30670
Funai
30675
Gateway
31077
GE
30815, 30522
GFM
30675
Go Video
31075, 31044, 30869,
30833, 30744, 30741,
30715
GoldStar
30869, 30741
Grundig
30539
For assistance call 1(800) 332-2119
80
Appendices
Appendix A: Programming the Remote Control, continued
DVD Players
Harman/
Kardon
Helios
Hello Kitty
Hitachi
Hiteker
Humax
iLo
Initial
Insignia
Integra
JBL
JVC
jWin
Kawasaki
Kenwood
KLH
Lenoxx
LG
LiteOn
Magnavox
Marantz
McIntosh
Memorex
Microsoft
Mintek
Mitsubishi
Myryad
NAD
Norcent
Olevia
Onkyo
Oppo
Panasonic
Philco
Philips
PianoDisc
31229, 30702, 30582
32192, 32080
30831
30664, 30573
30672
31588, 31500
31472, 31348
31472
32596, 32428, 32095,
30675
32147, 31769, 30627,
30571
30702
32365, 31602, 31550,
31275, 31164, 30867,
30623, 30558
31049
30790
30534, 30490
31020, 30790
31127
31602, 30869, 30741,
30591
31656, 31058
31506, 31472, 31354,
31177, 30675, 30646,
30539, 30503
32414, 30539
31273
32213, 31270, 30831,
30695
32083, 30522
31472
31521, 30521
30894
32572, 30741
31107, 31003
32331
32147, 31769, 30627,
30503
32545, 32185, 31224,
30575
31762, 31641, 31579,
30703, 30632, 30503,
30490
30675
32084, 32056, 31340,,
31267, 30675, 30646,
30539, 30503, 32434,
31506, 31354
31024
Downloaded From TV-Manual.com Manuals
DVD Players
Pioneer
31571, 31512, 31460,
30632, 30631, 30571,
30525, 30142
32442
Polaroid
31086, 31061, 31020
Polk Audio
30539
Portland
30770
Presidian
30675
Proceed
30672
Proscan
30522
ProVision
30778
RCA
32213, 31769, 30822,
30790, 30571, 30522
Rio
30869
Rotel
31178, 30623
Sampo
30752
Samsung
32069, 31470, 31075,
31044, 30820, 30573,
30490, 30199
32556, 32489, 32369,
32329
Sansui
30695
Sanyo
30873, 30695, 30670
Schneider
30646
Sharp
32250, 31256, 30752,
30675, 30630
Sherwood
31077, 31043, 30770,
30633
Sherwood
31077
Newcastle
Shinsonic
30533
Sonic Blue
30869
Sony
31633, 31536, 31516,
31431, 31070, 31033,
30864, 30533
Sylvania
30675
Symphonic
30675
TAG
30894
McLaren
Teac
30790
Technics
30703, 30490
Theta Digital 30571
Tivo
31512, 31503
Toshiba
31769, 31588, 31515,
31510, 31503, 31154,
30695, 30503
32277, 32006, 31608
Urban Con- 30503
cepts
Venturer
30790
Vizio
32563, 31226, 31064
Xbox
32083, 30522
For assistance call 1(800) 332-2119
DVD Players
Yamaha
32558, 32298, 30817,
30646, 30545,
30539, 30490
Zenith
30869, 30741, 30591,
30503
Blu-ray and HD-DVD
Denon
32258
Insignia
32596, 32428, 30675
Integra
32147, 31769
JVC
32365
LG
31602, 30741
Magnavox
30675
Marantz
32414
Microsoft
32083
NAD
32572
Olevia
32331
Onkyo
32147, 31769
Oppo
32545
Panasonic
31641
Philips
32434, 32084
Pioneer
32442, 30142
RCA
31769
Samsung
30199
Sharp
32250
Sony
31516
Sylvania
30675
Toshiba
31769, 31515
Vizio
32563
Xbox
32083
Yamaha
32298
Appendices
Appendix B: Bypassing
the Parental Lock
81
Mitsubishi Home Theater TV
738 Series
838 Series
Lock Bypass Instructions Have Been Filed for
Future Reference
Bypassing the Parental Lock
After you set the lock, you must use your pass code to:
• View a locked program
• View a locked channel
• View the locked TV
• Cancel the lock
• Enter the Lock menus
If you forget your pass code, you can view the locked
TV without entering your pass code. When prompted
for the pass code, press the number 9 and LAST keys on
the TV remote control at the same time. This process
temporarily unlocks the TV.
When entering the Lock menu, you will be prompted to
enter a pass code.
•
To change the pass code, press 9 and LAST at the
same time. Either enter a new pass code to open
the Lock menu and make changes or press EXIT to
close the menu.
•
If any of the locks are turned on and you exit the
menus when prompted for a new code, the old
code and all lock settings will be retained.
•
If all locks are turned off and you exit the menus
when prompted for a new code, then the previous
code will be erased.
IMPORTANT
When changing or deleting your pass code,
you must use the remote control included
with this TV. You cannot use a Mitsubishi
remote control from another component or a
“universal” remote.
IMPORTANT
Cut along the dotted line and file bypass
instructions in a safe place for future
reference.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
82
Appendices
This page intentionally left blank
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Appendices
83
Appendix C: HDMI Control of CEC Devices
Many new HDMI devices have a feature called Consumer Electronics Control (CEC) or HDMI Control.
HDMI Control allows one device, such as the TV, to
control other devices, such as an A/V receiver or disc
player. Use of CEC is optional.
Each manufacturer chooses which CEC functions to
support so it is difficult to predict which devices and
features are compatible with Mitsubishi’s HDMI Control.
You may find that CEC functions for a specific device are
limited.
To use HDMI Control, you must enable it in both
the TV and the device.
• In the TV. Enable HDMI control from the New
Device Found screen or from the Inputs > HDMI
Control menu.
• In the Device. Most devices with HDMI CEC compatibility let you turn it on or off in the device menus,
where it is typically listed as “HDMI Control.”
Enabling HDMI Control of CEC Devices
To ensure proper detection
• Power on HDMI devices before connecting them to
the TV.
• Connect and set up HDMI devices one at a time.
1. Power on the device and allow it to complete the
power-on sequence (boot up). Stop any playback.
2. Connect the device to one of the TV’s HDMI inputs.
3. When the TV detects the connection, the New
Device Found screen will appear.
Note: See “If the New Device Found Screen Has No
HDMI Control Option” on this page if there is no
HDMI Control option.
New Device Found screen with HDMI Control option.
This screen displays only if the device’s HDMI Control is
enabled.
Downloaded From TV-Manual.com Manuals
4. If prompted for a name,
highlight a name for the
device and press ENTER to
add a check. The device
itself may later override the
name assigned.
5. Highlight On and press
ENTER to add a check.
7. Highlight EXIT and press ENTER to close the New
Device Found screen.
Note: At any time after completing Auto Input Sensing, you can set the TV’s HDMI control on or off
in the Inputs > HDMI Control menu.
8. 838 Series. To supplement HDMI control with
NetCommand IR control, see page 62.
If the New Device Found Screen
Has No HDMI Control Option
If the New Device Found screen shows no option for
HDMI Control, one of these conditions applies:
• HDMI Control is turned off in the menus of the
new device
Action:
a. Highlight EXIT and press ENTER to close the
New Device Found screen.
b. Display the device’s setup menus and enable
the device’s CEC capabilities.
c. Wait for the TV’s New Device Found screen
to appear again.
d. If the New Device Found screen does not
appear, power off the device. Power on the
device and wait for the New Device Found
screen to display with the HDMI Control
option.
• The HDMI cable cannot support CEC
Action:
Upgrade your HDMI cable to one that supports
CEC.
• The device does not have CEC compatibility
Action:
-- Control the device with its own remote
control or program the TV’s remote control to
operate the device.
-- 838 Series. Use the TV’s NetCommand IR
control (page 62).
For assistance call 1(800) 332-2119
84
Appendices
Appendix C: HDMI Control of CEC Devices, continued
HDMI Control of an HDMI A/V
Receiver and Connected Devices
Y/ VIDEO
HDMI
1
2
1. Enable HDMI Control for the A/V receiver as
2.
3.
4.
5.
described in “Enabling HDMI Control of CEC
Devices” on the previous page.
Power on the HDMI device you wish to connect to
the A/V receiver (such as a disc player, cable box,
or satellite receiver). Allow the device to complete
the power-on sequence (boot up). Stop playback if
the device starts playing.
Connect the device to the A/V receiver with an
HDMI cable.
Select the device’s HDMI input on the A/V receiver’s front panel controls or remote control.
When the TV detects the connection, the New
Device Found screen will appear.
Note: If the TV is unable to detect the device, either
the device’s CEC capability is not enabled or
the device is not CEC compatible. Enable
HDMI control through the device’s menus
before continuing. You may need to temporarily connect the device directly to the TV to view
device menus.
6. Highlight On and
press ENTER to
add a check.
7. Highlight EXIT and press ENTER to close the New
8.
Device Found screen.
Optional: Connect the TV’s DIGITAL AUDIO
OUTPUT to an input on the A/V receiver. Use this
additional connection if:
• You want the ability to switch between the A/V
receiver speakers and the TV speakers.
• You want to use the A/V receiver to listen to
devices connected to the TV only, e.g., an
antenna input or camcorder.
9. 838 Series. If desired, perform NetCommand IR
Learning to supplement CEC functions. You must
first connect and place IR emitters for the devices.
See page 62.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Pb
AUDIO
OUTPUT
R AUDIO
L
Y/ VIDEO
ANT
L
Pr
DIGITAL
AUDIO
OUTPUT
LAN
3
R
INPUT 2
Note: Connect the A/V receiver to the TV with an
HDMI cable before making other connections.
DVI/PC AUDIO
R INPUT L
Pb
Pr
(480i / 480p / 720p / 1080i)
3D
GLASSES
EMITTER
INPUT 1
DIGITAL
AUDIO
OUTPUT
TV
Optional
analog or
digital audio
connection
HDMI cable
A/V receiver with
HDMI output
HDMI OUT
DIGITAL
AUDIO IN
Any connection
types
VCR
High-definition
DVD player
DVD player
Cable box
Connecting HDMI devices. The optional digital audio
connection allows you to hear audio through the A/V
receiver from devices connected to the TV only.
85
Appendices
Appendix C: HDMI Control of CEC Devices, continued
Resolving CEC Conflicts
Using HDMI Control
Because each manufacturer selects which CEC functions to support, some devices can conflict with other
devices. If control conflicts arise, you can:
• Turn off TV control of an individual CEC-enabled
device (see below).
• Turn off CEC in the setup menu of one of the
devices.
As an example of using HDMI Control, press PLAY on
the device itself to:
• Power on the TV
• Switch to the device (no need to display the
Input Selection menu)
• Begin play of the device
Turning Off the TV’s HDMI Control of a CEC Device
Test your equipment with the TV’s remote control to
find additional supported commands. See the table
below for commands that may be available, depending
on the individual device.
1. Press MENU on the TV remote control.
2. Highlight Inputs > HDMI Control.
3. Move to the device name and press ENTER to select
4.
Off to turn off the TV’s ability to control the device.
Press EXIT to clear the menu.
Inputs > HDMI Control menu
Removing an HDMI Device
1. Power off the device.
2. Disconnect the HDMI cable.
3. Press MENU on the TV remote control to enter the
4.
5.
6.
TV main menu.
Go to Inputs > Name.
Highlight the HDMI input name and press ENTER to
select Delete.
Press EXIT to clear the menus.
Direct Keys
CEC-enabled VCR, DVD, and DVR functions that
may be available:
Record/
Playback
Menu
Navigation
Channel
Tuning
Other
CH
Guide
Enter
Digits 0–9,
CANCEL
CANCEL
(to cancel)
ENTER
TOOLS
Check the
TOOLS menu
for supported
functions.
If you have a CEC-enabled A/V receiver, CEC-enabled
devices connected to the A/V receiver with an HDMI
cable may also be controllable. They can be selected
from the TV’s Input Selection menu.
CEC-enabled A/V receiver functions that may be
available:
• Try the VOL, MUTE, and menu-navigation keys.
• To open the A/V receiver menu, follow these steps:
1. While watching TV, press AUDIO.
2. Press until the TV Speakers option displays.
3. Press to select Off (to send audio to the A/V
receiver).
4. Press INPUT and highlight the A/V receiver icon
in the Input Selection menu.
5. Press TOOLS.
6. Select Menu from the Tools menu.
Inputs > Name menu with Delete selected for HDMI-3.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
86
Appendices
Appendix D: TV Care
Lamp-Cartridge Replacement
CAUTION: If the television is on, press POWER to turn it off. Unplug the television and
allow it to cool for at least one hour before attempting to replace the lamp cartridge.
Lamp
CAUTION
The light source for this television is a
lamp, which is part of a lamp cartridge
assembly. The life of the lamp can
BURN DANGER! HOT SURFACES INSIDE!
vary, based on the lamp itself, the air
Touch lamp cartridge handle only. Do not touch lamp or lamp cartemperature around the TV while it is
tridge housing. Keep lamp cartridge horizontal during removal. Do
operating, the selected lamp mode, and
not tilt as glass may come out and cause injury. Replace lamp caryour viewing patterns. Warmer air or
tridge only with the same part number 915B441001.
poor ventilation shorten the lamp life, as
does setting Lamp Energy to Bright
and turning the television on and off
frequently.
WARNING
Mitsubishi warrants the lamp for one (1) year from the date of original
THE ACCESS PANEL IS
TV purchase at retail.
PROVIDED WITH AN INTERLOCK
TO REDUCE THE RISK OF
To Order a New Lamp
EXCESSIVE ULTRAVIOLET
To Receive a Replacement Lamp Under Warranty
RADIATION. DO NOT DEFEAT
• Visit our website at www.mitsuparts.com.
ITS PURPOSE OR ATTEMPT TO
• Call (800) 553-7278. Please have model number, serial number,
SERVICE WITHOUT REMOVING
and TV purchase date available.
PANEL COMPLETELY.
To Purchase a Replacement Lamp After Warranty
Visit our website at www.mitsuparts.com or call (800) 553-7278. Order the
following:
Lamp Part Number 915B441001
Lamp-Substitution Alert
MDEA recommends that you use only genuine Replacement Lamp Assemblies purchased directly from Mitsubishi or a
Mitsubishi Authorized Dealer or Mitsubishi Authorized Service Center. MDEA advises that replacement lamps obtained
separately from the Lamp Cartridge and/or Lamp Assemblies obtained from unauthorized sellers may be incorrect for
your television, may not fit or perform properly and may even damage your television. MDEA can not be responsible
for the performance, reliability or safety of any replacement lamps that are obtained from unauthorized sources.
WARNING
•
•
•
•
•
•
Do not remove the lamp cartridge immediately after turning off the television. You may get burned because the
lamp is very hot. Allow the television to cool for at least one hour before replacing the lamp cartridge.
Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire.
Do not touch the lamp glass element. It may be very hot and break, causing injuries or burns.
Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical
shock. If a foreign object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for service.
Install the lamp cartridge securely. Failure to do so may cause a fire.
Do not touch the lamp glass elements. Oils from your fingers may cause premature lamp failure.
Hg
= MERCURY
THE LAMP INSIDE THIS PRODUCT CONTAINS MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance at www.eiae.org
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
87
Appendices
Appendix D: TV Care, continued
Replacement Procedure
Removing the Old Lamp Cartridge
1. Turn off TV power and unplug the TV. Allow the
2.
3.
4.
5.
6.
lamp to cool for at least one hour before proceeding.
After the lamp has cooled, remove the cover of the
lamp compartment, located on the back of the TV.
Refer to figures 1 and 2. Use a #2 (medium) Phillips
screwdriver to loosen the screw securing the cover.
Keep the screw and cover for re-installation
With a medium Phillips screwdriver, loosen the two
screws securing the lamp cartridge until they disengage from the mating threads. These are captive
screws and cannot be separated from the lamp
cartridge.
Fully open the bag supplied with the replacement
lamp and set the opened bag aside.
Gently grasp the handle of the lamp cartridge and
pull the old cartridge straight out. See figure 3.
CAUTION: Do not tilt or rotate the cartridge, as
small glass fragments may fall out.
Without tilting or putting down the lamp cartridge,
insert it into the opened bag. Close the bag while
being careful not to let any glass particles fall out.
Installing the New Lamp Cartridge
1. Do not touch the glass parts of the new lamp cartridge. Insert the new cartridge into the TV in the
same orientation as the old cartridge. Push on the
cartridge housing until it is fully seated.
2. Gently tighten the screws with the screwdriver.
AVOID OVERTIGHTENING!
3. Replace the plastic cover and retaining screws.
4. WASH YOUR HANDS THOROUGHLY, AS THIS
LAMP CONTAINS MERCURY.
Downloaded From TV-Manual.com Manuals
Figure 1
Figure 2
Figure 3
Use only replacement lamp part number
915B441001.
Disposal of the Old Lamp Cartridge
Contact your local authorities or the Electronic Industries Alliance at www.eiae.org for lamp-disposal or
recycling instructions. Do not dispose of the old lamp
with common trash.
For assistance call 1(800) 332-2119
88
Appendices
Appendix D: TV Care, continued
Cleaning Recommendations
Normally, light dusting with a dry, non-scratching duster
will keep your TV clean. If cleaning beyond this is
needed, please use the following guidelines:
First, turn off the TV and unplug the power cord from
the power outlet.
Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using a
vacuum cleaner with a brush attachment.
Top and Sides of the TV
•
Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel, microfiber, or a clean
cloth diaper, lightly moistened with water. Dry with
a second dry, soft, non-abrasive cloth.
Care of the Remote Control
Remote Control Tips
•
•
•
•
•
•
•
•
For longer life, use alkaline batteries.
Do not mix old and new batteries.
Be within 20 feet of the equipment.
Do not press two or more keys at the same time
unless instructed to do so.
Do not allow the unit to get wet or become heated.
Keep the unit out of direct sunlight.
Avoid dropping on hard surfaces.
Do not use harsh chemicals to clean. Use only a
soft, lightly moistened cloth.
Resetting the Remote Control
•
For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water
used to moisten the cloth. Rinse with a second
cloth moistened only with water. Dry with a third
dry, soft, non-abrasive cloth.
Screen
•
•
•
•
Follow the instructions for the top and sides, wiping
gently in an up and down motion.
Clean the entire screen evenly, not just sections of
the screen.
Do not allow liquid to drip down the screen, as
some liquid may enter the TV through the gap
between the screen and screen frame.
You may purchase Mitsubishi Screen Cleaner, part
number CLEANER-VSS, by calling (800) 553-7278.
General Cleaning Precautions
•
•
•
•
•
DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
DO NOT scrub or rub the TV harshly. Wipe it gently.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
If TV mode is selected and the TV does not respond
properly, reset the remote control.
1. Press and hold POWER for several seconds until the
indicator flashes twice and goes off.
2. Release the POWER key.
3. Press keys 0 0 9 3 5 and the indicator will flash
twice when you finish entering the code. When
entering the code, pause for a moment between
each key press to ensure it is recognized.
Low-Battery Indicator
If you press a key and the indicator flashes five times,
replace the remote control’s batteries.
Appendices
89
Appendix E: Troubleshooting
TV Reset Comparison Guide
You can resolve many common TV problems using
the reset functions described in the following table.
See also the troubleshooting suggestions later in this
appendix.
IMPORTANT
Before you change sound or picture settings: If
picture or sound settings seem wrong for a broadcast
channel (a channel from the ANT input, a cable box, or
satellite receiver), first check other channels from the
same input before changing settings. If most other
channels from the same input seem correct, there is
likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix
problems on individual channels also affect all other
channels on the same input.
Reset Name
When to Use
How to Use
Resulting Action
Format
If the picture shape
seems incorrect, use
the FORMAT key to
change the shape of
the picture.
Press FORMAT to cycle through the
aspect ratios available for the signal.
The last-used format for a signal
type is memorized for each input.
The next time the same input and
signal type are viewed, the lastused format will be recalled.
PerfectColor™/
PerfecTint™
Reset (838
Series)
(for the single
input currently
being watched)
When the color
1. While viewing the input being
intensities seem out
reset, press MENU and go to
of balance, use the
Picture > Perfect.
PerfectColor/PerfecTint 2. Press ENTER to display the
reset to reset the color
PerfectColor adjustment screen.
balances to the original
3. Press CANCEL to reset the colors.
factory settings.
Both PerfectColor and
PerfecTint are reset at
the same time.
All PerfectColor/PerfecTint
sliders are reset to the original
center position. The PefectColor/
PerfecTint settings for other
inputs remain unchanged.
A/V Memory
Reset
(for the single
current input)
When audio and/
or video settings for
a single input seem
incorrect, use A/V
Memory Reset to
return the input to
the original factory
settings.
During General TV Viewing
1. While viewing the input to reset,
press MENU and go to Picture >
Reset.
2. Press ENTER to highlight Reset.
3. Press ENTER again to reset.
While Using VUDU Movies and
Some VUDU Apps
Press TOOLS and 3.
Service and Customer Support
Service
If you are unable to correct a problem with your TV,
consult your Mitsubishi dealer or Mitsubishi Consumer
Relations at (800) 332-2119.
•
DO NOT adjust any controls other than those
described in this Owner’s Guide.
•
DO NOT remove the protective back cover of your TV.
Downloaded From TV-Manual.com Manuals
All Audio and Video settings for
the individual input are reset
except for the global settings
for audio Balance, Listen To,
Language, and settings in the
Picture > Advanced menu.
Customer Support
•
To order replacement or additional remote controls or lamp cartridges, visit our website at
www.mitsuparts.com or call (800) 553-7278.
•
For questions:
Call Consumer Relations at 800-332-2119.
E-mail: [email protected]
Website: www.mitsubishi-tv.com
For assistance call 1(800) 332-2119
90
Appendices
Appendix E: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
A/V Reset
(for all inputs)
To reset audio and
video adjustments for
all inputs to the original
factory settings.
While viewing the TV, press the
control-panel buttons INPUT and
VOLUME DOWN at the same time for at
least two seconds.
All Audio and Video settings are
returned to the original factory
settings, including global settings
not affected by Picture > Reset.
Does not affect settings in the
Picture > Advanced menu.
Channel
Memorization
To erase and
re-memorize channels
on the Ant input.
1. While viewing the TV, press
MENU to display the main menu.
2. Navigate to the Setup >
Channel menu.
3. Highlight the reception mode,
e.g. Ant Air.
4. Select All channels.
5. Highlight Scan.
6. Press ENTER to start channel
memorization.
All previously memorized channels for the antenna input are
erased and a new set of memorized channels is created. All
custom channel banks are
cleared. To add or delete individual channels, see the Setup
> Channel > Edit menu instructions on page 55.
Lock Menu
Pass Code
To change your Lock
menu pass code
See the cutout page from Appendix B,
page 81.
Allows establishment of a new
code.
Control-Panel
Lock Release
To re-enable the
control-panel buttons
after activation of the
Control-Panel Lock
Press and hold the INPUT button on
the control panel for ten seconds. If
the TV is powered off, you can then
press the POWER button to turn it on.
Allows the control panel to be
unlocked if the remote control is
misplaced.
Auto Input
Sensing for
HDMI
If the New Device
Found screen does
not appear when you
connect an HDMI
device.
1. Disconnect the HDMI device.
2. Delete the HDMI input in the
Inputs > Name menu (see page
57).
3. Power on and connect the new
device.
The New Device Found screen
will display.
System Reset
If the TV does not turn
on or off, does not
respond to the remote
control or controlpanel buttons, or has
audio but no video.
Press and hold the POWER button on
the control panel for ten seconds.
The TV will turn off. Power on the
TV and the green LED will flash
quickly for about one minute. The
changes you made most recently,
before using SYSTEM RESET, may
be lost.
TV Reset
To reset all consumeraccessible settings
and all memories to
the original factory
defaults.
1. While viewing the TV, press
MENU to display the TV main
menu.
2. With the main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
Use TV Reset if the TV
3. READ THE ON-SCREEN
can respond to conWARNING AND INSTRUCtrols but TV behavior is
TIONS.
abnormal.
• If you do not wish to use this
CAUTION: All ownerreset, press EXIT or MENU to
performed setups and
back out.
adjustments will be
• If you do wish to use the
erased.
reset, press ENTER to erase
all memories and settings.
The TV will start the initialization
process and then turn off.
Power on the TV and the front
green LED will start flashing. All
memory and settings outlined in
this Owner’s Guide will need to
be set again.
IMPORTANT:
Use this reset
only if other
troubleshooting
has been unsuccessful.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Appendices
91
Appendix E: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
VUDU
Reset VUDU
Account Password
You have forgotten
your account password.
Using a computer, go to
www.VUDU.com.
Reset your account password
from the VUDU website (requires
access to e-mail).
VUDU
Reset Parental
Controls Pass
Code
You have forgotten
your pass code.
Call VUDU Customer Care at
1-888-554-VUDU (8838).
VUDU Customer Care will reset
your pass code.
General TV Operation
Symptom
Remarks
1.
A fan has continued running more than two
minutes after the TV was powered off.
The room is too warm. When the TV is off, internal components
continue to draw power and must be cooled by the fan.
2.
The fan gets louder after the TV is shut off.
Normal operation. The fan speeds up to cool the lamp quickly
after the TV has been shut off.
3.
The TV remote control does not work.
•
•
•
•
•
4.
When I try to use the remote control, the POWER
key flashes five times.
Replace the batteries.
5.
TV does not respond to the remote control or •
to control-panel buttons and TV will not power •
on or off.
Unplug the AC power cord for 10 seconds.
Press and hold the POWER button on the control panel for 10
seconds to perform system reset.
6.
When a device is selected from the Input
Selection menu, the screen is blue or black (no
signal source).
•
•
Make sure the selected device is turned on.
Begin play of the device.
7.
You have forgotten your Lock menu pass code.
See Appendix B, “Bypassing the Parental Lock” on page 81.
8.
Rating restrictions are not working.
Open the Lock > Parental menu and:
• Verify that the ratings locks are active.
• Check the Lock Time/Unlock Time to check if rating restrictions are disabled.
• Rating restrictions apply only to content on the ANT input.
9.
On-screen displays appear each time you
change a function.
Normal TV operation.
10. A warning message appeared on screen
stating, “TV will shut down in a few seconds.
Please check if the air flow is blocked.”
Downloaded From TV-Manual.com Manuals
•
•
Check that the batteries are fresh and installed correctly.
Check that the control mode on the remote is set to TV.
Be no more than 20 feet from the TV when using the remote control.
Program the remote control to operate the TV or other device.
Reset the remote control. See “Resetting the Remote Control,”
page 88.
Internal TV temperature has exceeded proper levels. Cool
the room.
The TV has overheated. Clear blocked air vents and ensure
at least four inches of clearance on all sides of the TV.
For assistance call 1(800) 332-2119
92
Appendices
Appendix E: Troubleshooting, continued
General TV Operation
Symptom
11. I have turned on CEC for my HDMI devices but
control is erratic and I wish to disable it.
Remarks
•
•
•
First turn off the TV’s HDMI control for the specific device.
Open the Inputs > HDMI Control menu, select the device,
select Off.
Disable CEC on the device itself. See the device’s instructions.
If the problem persists, do the following:
1. Disconnect the device from the TV.
2. Open the Inputs > Name menu and select Delete for
the device.
3. Reconnect the device to the TV and Auto Input Sensing
will recognize the device with CEC disabled.
TV Channels
1.
Symptom
Remarks
The TV takes several seconds to respond to
channel changes.
•
•
•
•
2.
You cannot access a channel.
•
•
•
•
•
•
3.
When ChannelView list is displayed, information appears incomplete
•
•
•
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
It is normal for digital channels to take longer to tune in.
Press ENTER after entering a channel number to minimize
delays.
Use a 4-digit number for an over-the-air digital channel.
Use a 6-digit number for digital cable channels if your cable
service is able to recognize 6-digit channel numbers.
Use number keys instead of CH.
Be sure the channel you want to view is in memory.
Check that the TV is switched to the correct device or
antenna for that channel by pressing the INPUT key.
Make sure the Lock > Parental menu lock is set to Off.
If you cannot tune to a virtual digital channel even though the
TV has already memorized digital channels, tune to the physical channel number used by the broadcaster. The virtual
channel will then be automatically added to memory.
You may be trying to tune to an analog channel that is no
longer broadcasting.
Press INFO to update the display for the highlighted channel.
Make sure the TV clock is set correctly. Program information
is displayed only for the currently tuned channel.
Available information is sent from the broadcaster or cable
provider. No other data is available.
Appendices
93
Appendix E: Troubleshooting, continued
TV Power On/Off
Symptom
Remarks
1.
TV takes an excessively long time to power
on.
When powered on, the TV needs time to boot up, just as a computer does.
2.
You cannot program the TV to turn on automatically (Timer function)
•
•
The TV may be locked.
The clock may not be set.
3.
TV turned itself off and the light on the front
panel started to flash.
•
Momentary power fluctuation can cause the TV to turn off
to prevent damage. Wait for the green light to stop flashing
and turn the TV on again.
If the TV does not stay on, press the POWER button on the
control panel for ten seconds to perform System Reset. If
this happens frequently, obtain an AC line power conditioner/surge protector.
An unusual digital signal may have been received, triggering a
protection circuit. Wait for the light to stop flashing and turn TV
on.
•
•
4.
TV will not power off.
Press the POWER button on the control panel for ten seconds to
perform System Reset.
Picture
1.
Symptom
Remarks
Picture does not look like a high-definition
picture.
Compare the picture to the TV’s test picture (Picture > Picture+
> Test Picture) to check if the source signal is supplying a
lesser-quality image.
Not all signals are high-definition signals. To receive high-definition programming from your cable or satellite provider, you must
subscribe to the provider’s high-definition service. Some overthe-air broadcasts are in high-definition and can be received with
a high-quality antenna suited to your location.
2.
TV has sound but no picture.
•
•
•
Press MENU on the remote control. If the menu displays,
then there is a problem with the incoming signal.
Check that all video inputs are plugged in firmly to the
correct input jacks.
Press and hold the POWER button on the control panel for ten
seconds to perform System Reset.
3.
Picture has become dimmer.
•
•
•
4.
You cannot view a picture when playing a
VHS tape.
Check your VCR’s owner’s guide for further troubleshooting.
5.
VCR or DVD player’s on-screen menus jitter
up and down.
Stop playback. Possible cause: Many VCRs and DVD players
provide on-screen menus at only half-resolution that may
appear to jitter up and down.
6.
When viewing a stopped VCR, white lines
are rolling on the screen.
•
•
•
Downloaded From TV-Manual.com Manuals
The lamp is nearing the end of its life. Order a new lamp.
Adjust picture brightness and contrast to maximum levels.
Change Lamp Energy from Standard to Bright.
Turn off video mute for the VCR.
Begin playing the tape.
Change the VCR input from Line 1 to the VCR antenna input.
For assistance call 1(800) 332-2119
94
Appendices
Appendix E: Troubleshooting, continued
7.
A color program appears as a black and
white image, or the colors are dim, or the
screen is black.
•
•
•
8.
Picture from an HDMI input is noisy (poor
quality).
•
•
9.
The image from a computer appears distorted when viewed on the TV.
•
•
If using component video, check that the red, green, and
blue input cables are correctly connected to the red, green,
and blue component video jacks.
If using composite video, check that the incoming cable is
connected the TV’s green Y/VIDEO jack.
838 Series. The PerfectColor color balance has been incorrectly set. Reset the PerfectColor balance.
Compare the picture to the TV’s test picture (Picture >
Picture+ > Test Picture) to check if the noise is internal or
external to the TV.
Upgrade a Category 1 (unmarked) HDMI cable to a newer
type of high-speed HDMI cable.
Normal TV operation. The TV does not correct distortion in
the picture from a computer because the correction process
may cut off the edges of the image.
The aspect ratio may be wrong for the image. Press FORMAT
to change.
Sound
1.
Symptom
Remarks
There is no sound even when the
volume is turned up.
•
•
•
•
•
•
Check if the MUTE key is on.
The TV’s analog Listen to setting may be set to SAP (analog
program from the ANT input) but no SAP is being broadcast.
Check that the Sound > Audio > TV Speakers option is set to On
to hear sound from the TV speakers. Possibly the TV Speakers
option is Off or set to Center but there is no A/V receiver connected.
If using an A/V receiver, check that the Sound > Audio > TV
Speakers option is set to Off to hear sound from the A/V receiver
speakers.
Press and hold the POWER button on the control panel for 10
seconds to perform System Reset.
The language selected in the Setup > Antenna Digital Audio
menu is not being broadcast for the current program.
2.
The sound does not match the screen
picture.
The TV’s analog Listen to setting may be set to SAP (analog program
from the ANT input).
3.
The sound from my A/V receiver does
not match the screen picture (I should
hear the correct audio from my A/V
receiver).
•
•
Check that DIGITAL AUDIO OUTPUT and/or AUDIO/SURROUND
OUTPUT on TV’s connection panel is connected to the A/V
receiver.
Without this connection, devices connected only to the TV (and
not the A/V receiver) can be heard only from the TV speakers.
Note that this includes the ANT input, a device (such as a
camcorder) connected to the TV, and any other device sending
audio to the TV only.
If using a NetCommand-controlled A/V receiver, NetCommand
may be selecting the wrong A/V receiver audio input. Check the
A/V receiver’s NetCommand setup in the Inputs > AVR menu.
4.
Cannot select an audio-only device; it
does not appear in the Input Selection
menu.
Plug an unused video plug into the Y/VIDEO jack to activate Auto
Input Sensing. Assign the name CD/Audio or MP3 to make the
audio device selectable in the Input Selection menu.
5..
Sound is coming from the TV speakers
instead of the A/V receiver.
•
•
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Connect the TV’s AUDIO OUT to the A/V receiver.
Change TV Speakers setting to Off or Center.
Appendices
95
Appendix E: Troubleshooting, continued
Home Network
Symptom
Remarks
1.
I cannot connect the TV to the
network.
Go to the Setup > Network menu. Obtain the TV MAC address and
provide it to the router.
2.
I plugged in a wireless USB adapter,
but the wireless connection is not
working.
The network may be locked. Go to Setup > Network. Highlight the
network name and supply the pass code.
3.
The INTERNET key only goes to VUDU.
Normal operation. The TV receives all internet services through VUDU
Apps. The TV does not provide full internet access as does a web
browser on a computer.
NetCommand IR Control (NetCommand-equipped models only)
Symptom
Remarks
1.
•
NetCommand unable to learn specific device
keys.
•
•
•
•
A/V Device does not use IR format for remote control
signal. ITT and RF formats cannot be learned.
Room lighting may affect the signal. Have the remotes very
close (6 inches or less) to the TV during Learning.
Some, but not all, device key functions can be learned
by NetCommand. For example, POWER and PLAY may be
learned, but other functions may not.
The signal from the remote control may not be strong
enough. Insert fresh batteries and try Learning again.
The key was “learned” correctly but can be accessed only
from the Tools menu.
2.
The A/V receiver is the selected audio source A/V Receiver Set Up for Audio and Video Switching over HDMI
but there is no sound.
-- Check to see if the A/V Receiver power is turned on.
-- If the device is connected only to the TV (e.g., on
ANT or a front panel input), verify that the TV’s AUDIO
OUTPUT is connected to the A/V receiver and the
correct key has been “learned.”
-- The A/V receiver is not switching properly because
you have not learned the IR codes for the A/V receiver
inputs to which your devices are connected.
3.
There is no sound or picture from the A/V
receiver for my DVD player or other device
connected to the A/V receiver; the A/V
receiver should be sending video to the TV
over an HDMI cable.
(A/V Receiver Set Up for Audio and Video
Switching over HDMI)
The NetCommand A/V receiver setup is not switching audio
and video inputs properly because you did not “learn” the
A/V receiver’s IR codes for the device inputs. See “Automatic
Audio/Video Switching Over an HDMI Connection,” page 70.
4.
I’ve selected my DVD player or other surround sound device in combination with the
TV speakers but hear no sound from the TV
speakers.
A/V Receiver Set Up for Audio and Video Switching over HDMI
With your DVD player connected to the A/V receiver, only video
is passed from the A/V receiver to the TV because of copyprotection restrictions on the HDMI signal
5.
I “learned” the RECORD key for my VCR/DVR
but when I pressed the RECORD key, the VCR/
DVR did not record anything.
Check that the VCR or DVR is receiving a signal directly from
your cable box or satellite receiver.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
96
Trademark and License Information
Trademark and License Information
Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Manufactured under license from Cambridge Mechatronics Ltd.
Rapidfire and the 1... logo are trademarks of Cambridge Mechatronics Ltd
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Mitsubishi Electric is under license. Other trademarks and trade names are those of their respective owners.
Digital Light Processing® and DLP® are registered trademarks of Texas Instruments.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
ENERGY STAR® and the ENERGY STAR mark are registered U.S. marks. ENERGY STAR is a registered mark owned
by the U.S. government.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Imaging Science Foundation Certified Calibration Controls
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
“x.v.Color” and the “x.v.Color” logo are trademarks of Sony Corporation.
VUDU™ is a trademark of VUDU, Inc.
ChannelView™, DeepField™ Imager, Easy Connect™, EdgeEnhance™, NetCommand®, PerfectColor™, PerfecTint™,
Plush 1080p® 5G, Smooth120™, StreamTV™ are trademarks of Mitsubishi Digital Electronics America, Inc.
Network Service Disclaimer
Third party content and services, including without limitation home entertainment services by VUDU, Inc., are provided
in accordance with whatever terms and conditions are established by the third party providers and agreed to by you.
Mitsubishi Digital Electronics America (“MDEA”) has no control over any such third parties or any agreement you reach
with them. MDEA has no control over the networks or transmission facilities by which content and services are provided
by third parties. Your connection to the internet may vary in availability and quality. Customer service questions are to
be directed to the third-party provider, not MDEA.
MDEA DOES NOT WARRANT CONTENT OR SERVICES PROVIDED BY ANY THIRD PARTY, EITHER EXPRESSLY OR
IMPLIEDLY, FOR ANY PURPOSE. MDEA DOES NOT WARRANT THAT ANY THIRD PARTY SERVICE WILL REMAIN
AVAILABLE FOR ANY PERIOD OF TIME OR THAT IT WILL BE SATISFACTORY, UNINTERRUPTED OR ERROR FREE.
MDEA EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ANY THIRD PARTY CONTENT
AND SERVICES.
MDEA WILL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE, WHETHER IN CONTRACT OR TORT OR OTHER
LEGAL THEORY, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, ATTORNEY
FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING OUT OF, OR IN CONNECTION WITH, YOUR USE OF ANY
CONTENT OR SERVICE THAT IS PROVIDED TO YOU BY ANY THIRD PARTY, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Trademark and License Information
97
Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By
utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws
and treaties. The Software is licensed, not sold.
1.
LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software
only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.
RIGHTS AND LIMITATIONS.
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any
violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other violation
of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This license
is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any
provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned
by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the Software
is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and
treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is
recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MDEA.
5.
EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not
export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software
back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development,
or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in
U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S.
federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MDEA’S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE
ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MDEA’s
liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money
paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.
WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects
or other reproductive harm.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
98
Trademark and License Information
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users. We, the Free
Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to
your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute
copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in
new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you
distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must
make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to
copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’ sake, the GPL requires
that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such
problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom
of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose
computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL
assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or
organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting
work is called a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright
law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the
public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with
no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work
under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list
meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular
programming language, one that is widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component,
but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which
an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system,
and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run
it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and
to modify the work, including scripts to control those activities. However, it does not include the work’s System Libraries, or general-purpose tools or generally available
free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to
require, such as by intimate data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License
explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its
content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you
comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for you must do
so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty
adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing,
against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
If you are interested in obtaining open source code for this product, please contact Mitsubishi at
(800) 332-2119. A nominal handling and mailing charge may apply.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Trademark and License Information
99
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each
copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code;
keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided
that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified it, and giving a relevant date.
b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the
requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any
applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license
the work in any other way, but it does not invalidate such permission if you have separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined
with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are
not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not
cause this License to apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source
under the terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a
durable physical medium customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three
years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy
of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a
network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and
noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same
way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to
copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the
Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being
offered to the general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the
object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes,
or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of
coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of
the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of
whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions
of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the
modified object code is in no case prevented or interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the
right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the
Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third
party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been
modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself
materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are
applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without
regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions
may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered
work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement
the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing
it; or
c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the
original version; or
d) Limiting the use for publicity purposes of names of licensors or authors of the material; or
e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
f)
Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of
liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further
restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided
that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or
a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either
way.
8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will
automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
100
Trademark and License Information
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder
explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days
after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is
the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of
the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have
been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence
of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate
or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your
acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this
License. You are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations.
If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the
work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the
predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty,
or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any
patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called
the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be
infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent
with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale,
import and otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and
under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source
to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your
conveying the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you
have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent
license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent
license you grant is automatically extended to all recipients of the covered work and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more
of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the
business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the
third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work
conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless
you entered into that arrangement, or that patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under
applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then
as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you
convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero
General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered
work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit
to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later version”
applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation.
If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s public statement of acceptance of a
version permanently authorizes you to choose that version for the Program.
Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of
your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES
AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that
most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the
Program in return for a fee.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Trademark and License Information
101
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991
Free Software Foundation, Inc.
675 Mass Ave, Cambridge, MA 02139, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to
guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the
Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by
the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software
or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate
to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure
that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify
the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is
modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will
not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not
licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this
General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another
language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running
the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of
any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the
most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying
that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print
an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.
But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this
License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or
distribution medium does not bring the other work under the scope of this License.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
102
Trademark and License Information
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2
above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on
a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing
source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the
source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code
from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights,
from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program
or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work
based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program
or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly
or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as
a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/
donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who
places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in
or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you
have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program
does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission.
For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision
will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE
WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Warranty
103
Mitsubishi Home-Cinema Television Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this
television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects
arising from improper workmanship and/or material:
a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a
period of thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any software incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase
at retail. We will repair or replace, at our option, any defective part without charge for the part. Parts used for replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the remainder of the original warranty period.
b. Embedded Software. MDEA warrants that all software incorporated into this television set (the “Embedded
Software”) will perform in accordance with the functional description of Embedded Software in all material respects,
but MDEA does not warrant that the Embedded Software is error-free. The limited warranty contained in this section
shall continue for a period of one (1) year from the date of the original purchase at retail. If, after prompt notice within
the warranty period, MDEA determines that the Embedded Software has failed to perform in accordance with such
functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA shall modify or replace the nonconforming Embedded Software at
no charge to you, which at MDEA’s sole discretion may be fulfilled by means of modification or replacement software
contained on a replacement memory card for Customer installation. The foregoing shall be MDEA’s sole obligation
to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to
your acceptance of and compliance with the terms of the Software License Agreement applicable to this television,
and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is modified or
changed in any manner except as specifically authorized by MDEA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticular screen if it proves defective. For certain items that are designed to be replaced by the consumer, including (but
not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other
parts, we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for
one (1) year from the original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within
the applicable warranty time period.
e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the
image using small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of performance and quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MDEA warrants
only that the percentage of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and
correct customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your
MITSUBISHI dealer, by writing at the address provided below, calling MDEA at the 800-332-2119, or by using the
support feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your
television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center.
If not, you must either deliver your television to an authorized service location at your own expense, or pay for any
travel and/or transportation costs the service center may charge to and from your home. Actual service labor will be
provided without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service.
Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE
OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However,
please return the Owner Registration Card so that we can contact you should a question of safety arise which could
affect you.
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
104
Warranty
d. To obtain a replacement lamp, order the lamp directly from the MDEA Parts Department at (800) 553-7278.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where
such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other
than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to
carry out any maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged
by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered,
defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage
caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage
caused by electrical system or lightning. This limited warranty also excludes service calls where no defect in the
product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal
unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or any other
damages arising from product installation, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection
with any external audio receiver, antenna, cable or satellite systems, or service of products purchased or serviced
outside the U.S.A. Please consult the operating instructions contained in the Owner’s Guide furnished with the
product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental, special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the
state where the television was purchased and the laws of such state will govern.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Index
Index
A
Accent Lighting 56
Anamorphic Picture Format 32
Antenna Input (ANT) 20, 21
Setting Up 12
Signal Strength for Digital Channels 30
Antennaweb.org 55
Audio Lock (A/V receiver control) 76
Audio Output Jacks 20
Auto Input Sensing 13
Auto-Off (Sleep Timer) 28
Auto-On (Timer) 54
A/V Receiver
and TV’s Remote Control 75
Audio Lock 76
Center Channel 27
Connecting 22, 25
Controlling Sound Volume 31
Disconnecting 31
NetCommand IR Control 68, 69
Controlling a Device Connected
to the A/V Receiver 46, 72
Video and Audio Switching via
HDMI 71
B
Batteries 7
Blue Glow 56
Bluetooth Audio Playback 38
Bright (Lamp Mode) 56
Brightness (picture adjustment) 48
C
Cable Box
and TV’s Remote Control 75
Connecting 23
Captions Menu 53
CD Player 37
CEC (Consumer Electronics Control)
46, 83
A/V Receiver 31, 84
Troubleshooting 92
Center Channel 27
Channels
antennaweb.org 55
Changing Channels 8
Favorites (Fav) 28
Physical/Virtual Channel Numbers 55
Scan (memorize) 12, 55
Troubleshooting 92
Tuning 14
ChannelView™ Channel Listings 29
Cleaning 88
Clock, Set Date and Time 54
Downloaded From TV-Manual.com Manuals
I
Closed Captions 53
Color Adjustments
Menu Controls 48
Reset Color 49, 89
Computer 17, 18
Contrast 48
Control Panel 11
Control Panel Lock 11, 61
D
Date. See Clock
Default Settings, Returning to 89
DIGITAL AUDIO OUTPUT 22
DVD Player
and TV’s Remote Control 75
Connecting 22, 23
DVI Device, Connecting 17, 23
E
Energy Settings 56
ENERGY STAR 6
F
Fan Noise 4
FAV (Favorite Channels) 28
Film Mode 48
FORMAT (picture shape) 16
Freeze Picture (PAUSE key) 9
Front Panel
Blue Glow Accent Lighting 56
Controls 11
G
Game
3D Video 33
Game Picture Mode 47
HDMI Cables for Games 21
GUIDE Key
ChannelView 29
HDMI Control 85
NetCommand Control 66, 67
H
105
HD (High-Definition) Signal) 30
HDMI
A/V Receiver with HDMI 25
Changing Out an HDMI Device
and Auto Input Sensing 13
Connecting an HDMI Device 17,
22
HDMI Cable Types 21
HDMI Control of CEC Devices 83
HDMI Jack 21
Removing an HDMI Device from
the Activity Menu 57
Headphones 52
INFO Key
ChannelView 29
Status Display 30
INPUT Key/Input Selection Menu
Change Input Name 57
Choose Viewing Source 14
NetCommand-Controlled Switching of A/V Receiver Inputs 65
Removing a Disconnected HDMI
Device 57
Internet 43
IR Emitter Placement 63
L
Lamp Cartridge Replacement 86
Lamp Energy 56
Language
Changing the Menu Language
54
In Digital Programs 54
SAP (Second Audio Program) 51
Learn 57. See also NetCommand IR
Control
Letter Box Image Display 32
Level Sound 51
Listen To 51
Listings 29
Lock TV
Bypassing the Lock 81
Lock by Channel 61
Lock by Ratings 60
Lock by Time 61
Lock Control Panel 61
Preset V-Chip Blocking 59
M
Memorizing Channels 12, 55
Add Single Channel to Memory
55
MP3 Player (audio-only connection)
37
MUTE Key 9
N
NetCommand IR Control
About 62
A/V Receiver Control 69
Initial Setup for Most Devices 64
Operating 65
Troubleshooting 95
P
Pass Code
Resetting 81
Setting 59
VUDU Password 91
PerfectColor 49
Photo Viewing 36
For assistance call 1(800) 332-2119
106
Index
Picture
Picture Menu Adjustments 47
Picture Quality and Film Mode
48
Shape (format) 16, 18, 32
Troubleshooting 93
Power On/Off 8
Troubleshooting 93
R
Ratings (TV and Movie) 60
Rear Speakers 42
Remote Control
Keys and Functions 9
Programming Instructions 76
Reset 88
Reset
A/V Memory Reset (for the current input) 89
A/V Reset (for all inputs) 90
HDMI Auto Input Sensing 13
Pass Code 81
PerfectColor/PerfecTint 89
Remote Control 88
Remote Control Audio Lock 76
System Reset 11
TV Reset Comparison Guide 89
S
Safety Instructions 5
SAP (second audio program) 51
Satellite Receiver
and the Remote Control 75
Connecting 17, 22, 23
Scan (memorize channels) 55
ScreenSaver 48
SD (Standard-Definition Signal) 30
Service and Support 89
Signal Definitions 30
Signal Strength Indicator 30
Sleep Timer 28
Sound
Controlling A/V Receiver Volume
(NetCommand) 69
Surround Sound
Rear Speakers 42
Simulated Surround Sound 51
Sound Projector 39
TV Audio Outputs 22
System Reset 11, 90
T
3D GLASSES EMITTER Jack 21
3D Video 33, 50
Time. See Clock
Timer (auto-on) 54
Time Zone. See Clock
Tools Menu 10
Troubleshooting 89
U
USB Port 21
Auto Detection 13
File Types 35
USB Media Player Menu 36
Wireless Network Adapter 44
Wireless Subwoofer 26
V
V-Chip Ratings
Definitions 60
In Status Display 30
VCR
Connecting 24
Troubleshooting 93
Video from a Digital Camera 37
Video Game. See Game
VUDU Movie Service 45, 91
W
Wireless Network 44
Wireless Subwoofer 26
Audio Lock 76
Level Sound 51
Menu Adjustments 51
Sound Mode (audio effects) 51
Sound Projector 39
Standard-Definition Signal 30
Standard Lamp Mode 56
Stand Part Number 4
Status Display 30
Stereo System. See A/V Receiver
Stream TV 43
Subwoofer 26, 51, 52
Downloaded From TV-Manual.com Manuals
For assistance call 1(800) 332-2119
Downloaded From TV-Manual.com Manuals
Website:
www.mitsubishi-tv.com
E-mail:
[email protected]
Call Consumer Relations for operational or connection assistance at
800-332-2119
To order replacement or additional
remote controls, lamp cartridges, or NetCommand IR emitters,
Visit our website www.mitsuparts.com
or call
800-553-7278
SYSTEM RESET
If the TV does not respond to the remote control,
control-panel buttons, or will not power on/off, press
and hold the POWER button on the control panel for
ten seconds.
The TV will turn off. Power on the TV and the green LED
will flash quickly for about one minute. Recent settings
changes may be lost.
V43+/V43++
© 2010 Mitsubishi Digital Electronics America, Inc.
Downloaded From TV-Manual.com Manuals
V43+_V43++_IB_a_20100903