PHONES
(044) 360-7-130
(050) 336-0-130
(063) 788-0-130
(067) 233-0-130
(068) 282-0-130
Internet store of
autogoods
ICQ
294-0-130
597-0-130
SKYPE
km-130
CAR RECEIVERS — Receivers • Media receivers and stations • Native receivers • CD/DVD changers • FM-modulators/USB adapters • Flash memory • Facia plates and adapters • Antennas • Accessories |
CAR AUDIO — Car audio speakers • Amplifiers • Subwoofers • Processors • Crossovers • Headphones • Accessories | TRIP COMPUTERS — Universal computers • Model computers • Accessories |
GPS NAVIGATORS — Portable GPS • Built-in GPS • GPS modules • GPS trackers • Antennas for GPS navigators • Accessories | VIDEO — DVR • TV sets and monitors • Car TV tuners • Cameras • Videomodules
• Transcoders • Car TV antennas • Accessories | SECURITY SYSTEMS — Car alarms • Bike alarms • Mechanical blockers • Immobilizers • Sensors • Accessories | OPTIC AND LIGHT — Xenon • Bixenon • Lamps
• LED • Stroboscopes • Optic and Headlights • Washers • Light, rain sensors • Accessories | PARKTRONICS AND MIRRORS — Rear parktronics • Front parktronics • Combined parktronics • Rear-view mirrors
• Accessories | HEATING AND COOLING — Seat heaters • Mirrors heaters • Screen-wipers heaters • Engine heaters • Auto-refrigerators • Air conditioning units • Accessories | TUNING — Vibro-isolation
• Noise-isolation • Tint films • Accessories | ACCESSORIES — Radar-detectors • Handsfree, Bluetooth • Windowlifters • Compressors • Beeps, loudspeakers • Measuring instruments • Cleaners • Carsits
• Miscellaneous | MOUNTING — Installation kits • Upholstery • Grilles • Tubes • Cable and wire • Tools • Miscellaneous | POWER — Batteries • Converters • Start-charging equipment • Capacitors
• Accessories | MARINE AUDIO AND ELECTRONICS — Marine receivers • Marine audio speakers • Marine subwoofers • Marine amplifiers • Accessories | CAR CARE PRODUCTS — Additives • Washer fluid •
Care accessories • Car polish • Flavors • Adhesives and sealants | LIQUID AND OIL — Motor oil • Transmission oil • Brake fluid • Antifreeze • Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in
Kyiv and other cities, delivery by ground and postal services. Our experienced
consultants will provide you with exhaustive information and help you to chose
the very particular thing. We are waiting for you at the address
http://130.com.ua
a
u
.
m
o
c
.
0
PRELIMINARY
3
1
MANUAL
TH uno
ADVANCED
Car Audio Mono Amplifier
www.audison.eu
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
INDEX
THESIS - The project
Packaging Contents
Installation
Fixing template
Rear Panel
Functions Description
How to remove the panel / the protection knob
How to connect the power supply
How to replace the fuse
How to connect the speakers using
one amplifier (MASTER)
How to connect the speakers using two amplifiers
in BRIDGE mode (MASTER+BRIDGE)
How to connect the speakers using more than one
amplifier in CHAIN mode (MASTER+CHAIN)
Input controls
Functions Description
How to move from one sensitivity range to another
Front Panel
Functions Description
How to connect the remote
How to connect the source through the preamplified analog input (MASTER mode)
How to connect the source through the IN R preamplified analog input (MASTER mode)
How to connect the source through the IN L preamplified analog input (MASTER mode)
Electronic Crossover
X-Over Slope 12 dB
X-Over Slope 24 dB
How to insert
Examples
TH amplifier on Subwoofer, Analog Input
Two Way + Sub, bi-amplified, TH amplifier, Analog Input
Three Way + Sub, multi-amplified, TH amplifier, Analog Input
Two Way + Sub, bi-amplified, with and without TH amplifiers, Analog Input
Three Way + Sub, multi-amplified, with and without TH amplifiers, Analog Input
THESIS
ASC (AMPLIFIER STATUS CONTROLLER)
INPUTS AND PRE-AMPLIFIER
ASC - Amplifier Status Controller
Functions Description
Setup Amplifier: Main Input
Digital Inputs
How to adjust the volume control and input selector using a digital source
Front Panel
How to achieve same output volume level using an analog source
(with its own volume control) and a digital source
How to connect a source through the optical digital input
in a system featuring more then one TH amplifier
How to connect a source through the optical digital input
in a system featuring other non-TH amplifiers
How to connect an analog and a digital source in a system
featuring more than one amplifier
How to connect an analog and a digital source in a system
featuring other non-TH amplifiers
a
u
.
m
o
c
.
0
2
Autogood products internet store http://130.com.ua
General
3
1
OWNER’S MANUAL / TH uno
INDEX
How to connect an analog and a digital source in a system
featuring more than one TH amplifier (IN R or IN L)
How to connect an analog and a digital source in a system
featuring other non-TH amplifiers (IN R o IN L)
ASC - Amplifier Status Controller
Setup Amplifier: Amp ID
Setup Amplifier: Amp ID-Preout
Front Panel
How to adjust the PRE OUT analog output
ASC - Amplifier Status Controller
Setup Amplifier: X-Over Slope
DUAL POWER & BIAS CONTROL
Setup Amplifier: DUAL POWER Settings
DUAL POWER Values
How to change presets on the Memory
Examples
Three Way + Sub, multi-amplified, TH amplifiers, Digital Input
Three Way + Sub, multi-amplified, TH amplifiers, Analog + Digital Input
Three Way + Sub, multi-amplified, with both TH and non-TH amplifiers, Analog + Digital Input
ASC - Amplifier Status Controller
Status Monitor
Runtime Monitor
Info and Alert sentences
DRC - Digital Remote Control
Info and Alert sentences
How to connect
How to install
ACNet - Audison Control Network
Technical Specifications
a
u
.
m
o
c
.
0
General
3
1
3
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
THESIS
The Project
The roads travelled to reach “the Sound” have created a conceptual cross-road, where state of the art digital
technology and traditional techniques have gone their separate ways.
They both have benefits of a different nature, yet are capable of merging together to achieve much higher
Sound quality levels.
The Thesis amplifiers are born from these considerations. The parts related to signal amplification are
manufactured using the highest level of analog technology while, at the same time, the input section along with
the processing and monitoring functions of the amplifier are the result of the most advanced digital technology.
The TH due is a two-channel power amplifier, designed for use in car. It is technologically progressive,
featuring original circuitry, with extraordinary sound, consistent with Audison tradition.
a
u
.
m
o
c
.
0
Sections:
This manual is divided into sections allowing the use of the TH amplifier in standard settings or
using its specific features in “digital” settings. Each section is marked by its corresponding
bookmark.
General Part:
3
1
Despite the endless settings and customising possibilities ASC (Amplifier Status Controller)
offers, the TH amplifiers can also be used in a traditional way, taking advantage of the analog
inputs and of the controls which provide the signal to the final stages.
The setting of the sensitivity, stereo or bridged mono configuration, the inputs sensitivity, the
electronic crossovers on slide-through boards as well as the PRE bypass out, anyway let to
include the TH within the traditional systems or to to build amplifying chains with absolute
audiophile quality.
Digital Domain:
The TH amplifiers feature ASC (Amplifier Status Controller) which provides several factory
functions for the complete control of all the amplifier’s functions.
Heart of the system is a digital power microprocessor. It manages the amplifier functions and
communicates with the user through a control panel as well as the Display Monitor, featuring the
DRC remote control or, in a more complete and direct way, through the ACNet Audison
Controller Network software.
The ASC menu allows the amplifier set up, monitors the working conditions, viewable through a
Status Monitor feature, also making the data available on the display intermittently. A USB
connector enables the connection of the system to a computer, while the AC Link (Audison
Control Link) allows the creation of communication network. The software will take care of the
functional operations for all the amplifiers within the whole chain (system), providing a simple
and complete interface. A revolutionary method for configuration which, up to know, were
impossible to achieve with traditional designs.
4
Autogood products internet store http://130.com.ua
General
Classic Domain:
Classic domain Digital domain
The TH amplifiers need to be connected like any other amplifier, in compliance with safe
working conditions. Installation as well as power supply and speaker connections have to be
made properly, following the standard methods a specialty store normally follows.
OWNER’S MANUAL / TH uno
Packaging Contents
- TH uno amplifier
- Printed Quick Start Guide
- 1.0 m AC Link (RJ-12) cable
- 1.0 m AD Link (RJ-45) cable
- 2.0 m USB cable
- USB/AC Link converter
a
u
.
m
o
c
.
0
- TH crossover kit composed of:
HI
PA
SS
Band
-
N. 1 TH-MXR stereo module
Filte
Modrs
e
Hi
Freq
uenc
y
TH
-M
Sett
ing
XR
.1
Mon
Lo o
Pass
LO
PA
SS
24
dB
-
N.8 frequency set modules (SS1-SW1-SW2-WM1-WM2-MT1-WT1-MT2)
-
N. 2 CFB customizable modules
3
1
- N. 4 Fixing screws and plastic bushing
- Multispanner tooling
- 150 A AFS spare fuse
- CD ROM with:
ACNet software
This Advanced Manual (.pdf)
AC Link drivers
Test tracs
Available accessories (not included):
-
DRC control panel
-
4.5 m DRC/AC Link cable
-
N.2 fixing brackets
General
DRC - Digital Remote Control
5
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
TH uno
External size
259 mm / 10.19“
Installation
510 mm / 20.07“
a
u
.
m
o
c
.
0
6
Autogood products internet store http://130.com.ua
f 4.3 x 10.5 mm
3/16” x 7/16”
General
-
Speaker A
0 180
PHASE
CAP
BRIDGE
CHAIN
MASTER
478 mm / 18.82”
160 mm / 6.30”
12V
TH uno
LEVEL
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
FUSE 150A
Hi :
Lo :
PUSH
Fixing size
-
Speaker B
2)
+
1)
3
1
+
How to fix
a
u
.
m
o
c
.
0
3
1
7
Autogood products internet store http://130.com.ua
Fixing tem
A
A
B
a
u
.
m
o
c
.
0
Fixing template
3
1
8
Autogood products internet store http://130.com.ua
A
B
A
B
8
7
901
654
a
u
.
m
o
c
.
0
Mode A
3
1
2
3
level panel
spacer
66 mm (2.6”)
Mode B
level panel
spacer
9
Autogood products internet store http://130.com.ua
26 mm (1.02”)
A
8
7
901
654
2
3
level panel
spacer
a
u
.
m
o
c
.
0
3
1
66 mm (2.6”)
B
level panel
spacer
26 mm (1.02”)
10
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
Rear Panel
Functions Description
5
FUSE 150A
Speaker A
+
Speaker B
-
-
12V
CAP
+
-
3
2
1
4
SPEAKER A
+ CAP
- POWER +
SPEAKER B
+
-
+
-
12 V
a
u
.
m
o
c
.
0
1 • POWER: Positive and negative terminals for 12 V car voltage supply. Size of connectors is 10 mm diameter
(2 AWG). Warning: connect positive and negative (GND) with polarity as indicated in the terminal. A wrong
connection cause an amplifier damage.
2 • +CAP: Terminal to connect positive pole of external capacitor.
3 • SPEAKER A: Terminals to connect speakers. Size of connectors is 6 mm (6 AWG). Pay attention to
connect speaker with polarity as indicated, wrong polarity causes a phase problem in the audio system.
4 • SPEAKER B: Terminals to connect speakers. This output is connected in parallel with SPEAKER A to allow
the connection of several speakers.
5 • FUSE: Protection Fuse Connection Audison AFS 150 A.
3
1
How to remove the panel / the protection knob
Speaker A
+
FUSE 150A
-
CAP
-
12V
Speaker B
+
+ CAP
+
-
A
- POWE
R +
SPEAKER
B
12 V
+
-
11
Autogood products internet store http://130.com.ua
General
SPEAKER
OWNER’S MANUAL / TH uno
Rear Panel
How to connect the power supply
a
u
.
m
o
c
.
0
Speaker A
+
FUSE 150A
-
CAP
-
12V
Speaker B
+
SPEAKER
+ CAP
+
- POWE
R +
B
-
L
L :m
Ø : m in 1
M ax 6
AX 26 m
:2 m m
AW m (5/8
G (1”) ”)
+
Fuse Holder
Battery
Ground
Ground
General
Super
Capacitor
SPEAKER
-
12 V
3
1
-
A
12
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
Rear Panel
How to replace the fuse
a
u
.
m
o
c
.
0
Fuse AFS 150 A (provided)
3
1
Speaker A
+
SPEAKER
+
FUSE 150A
-
CAP
-
12V
Speaker B
+
-
A
+ CAP
- POW
ER +
SPEAKER
B
+
-
General
12 V
13
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
Rear Panel
How to connect the speakers using
one amplifier (MASTER)
PUSH
a
u
.
m
o
c
.
0
LEVEL
Hi :
Lo :
-
12V
Speaker B
+
-
A
+ CAP
+
0 180
PHASE
FUSE 150A
-
CAP
SPEAKER
BRIDGE
CHAIN
MASTER
- POWE
R +
SPEAKER
B
-
12 V
+
-
L
L :m
Ø : ma in 1
M x 2
AX 16 m
:6 m m(
AW m 1/2
(
G 5/8 ”)
”)
3
1
Speaker A
+
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
Speaker B
connected in parallel
with Speaker A
General
Speaker A
14
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
Rear Panel
How to connect the speakers using two amplifiers
in BRIDGE mode (MASTER + BRIDGE)
8
7
901
654
2
3
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
a
u
.
m
o
c
.
0
Speaker A
+
FUSE 150A
-
CAP
-
12V
Speaker B
+
SPEAKER
-
A
+ CAP
+
- POWE
R +
SPEAKER
B
-
+
12 V
-
3
1
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
Disabled
0 180
PHASE
Speaker A
+
FUSE 150A
-
CAP
-
12V
Speaker B
+
SPEAKER
+ CAP
+
-
A
- POWE
R +
SPEAKER
B
12 V
+
-
General
Speaker
Min 2 7 Load
Disabled
Disabled
15
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
Rear Panel
How to connect the speakers using more than one
amplifier in CHAIN mode (MASTER + CHAIN)
8
7
901
654
2
3
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
Speaker A
FUSE 150A
a
u
.
m
o
c
.
0
+
-
CAP
-
12V
Speaker B
+
SPEAKER
+ CAP
+
- POWE
R +
SPEAKER
3
1
B
-
+
12 V
Speaker
Min 1 7 Load
-
A
-
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
Disabled
0 180
PHASE
Disabled
Disabled
Speaker A
+
FUSE 150A
-
CAP
-
12V
Speaker B
+
SPEAKER
-
A
+ CAP
+
- POWE
R +
SPEAKER
B
+
12 V
-
Speaker
Min 1 7 Load
8
7
PUSH
LEVEL
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
Disabled
0 180
PHASE
Disabled
Disabled
Speaker A
+
FUSE 150A
-
CAP
-
12V
Speaker B
+
SPEAKER
-
A
+ CAP
+
2
3
- POWE
R +
SPEAKER
B
12 V
+
-
Speaker
Min 1 7 Load
16
Autogood products internet store http://130.com.ua
General
Hi :
Lo :
654
OWNER’S MANUAL / TH uno
Input controls
Functions Description
1
2
3
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
a
u
.
m
o
c
.
0
1 • LEVEL: Input sensitivity adjustment. It features 2 ranges, Hi from .3 to 1.2 VRMS and Low from 1.2 to 4.8
VRMS. By pushing for three seconds on the knob you can change the range. To see voltage value and
range check the ASC display. Those controls are also available if ACNet sofware is used.
2 • AMP MODE: This switch sets the working mode of the amplifier (see pages 14 - 15 - 16).
3 • PHASE: This switch regulates the absolute acoustic phase of the amplifier.
3
1
How to move from one sensitivity range to another
1)
2)
TH uno
PUSH
LEVEL
Hi :
Lo :
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
High level
PUSH
PUSH
LEVEL
Hi :
Lo :
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
BRIDGE
CHAIN
MASTER
0 180
PHASE
LEVEL
Hi :
Lo :
TURN THE KNOB TO REGULATE THE LEVEL
PRESS THE KNOB FOR 3” TO CHANGE
THE RANGE FROM LO TO HI
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
BRIDGE
CHAIN
MASTER
0 180
PHASE
TURN THE KNOB TO REGULATE THE LEVEL
PRESS THE KNOB FOR 3” TO CHANGE
THE RANGE FROM HI TO LO
NOTE: when passing from LO to HI level, sensitivity is automatically set on the lowest value. When adjusting
sensitivity, ASC will show the clipping, if occurring, on the display (see point 7, page 55)
17
Autogood products internet store http://130.com.ua
Classic domain
Low level
OWNER’S MANUAL / TH uno
Front Panel
Functions Description
1
3
2
8
7
4
7
901
654
2
3
8 6
5
9
a
u
.
m
o
c
.
0
1 • IN L/R: Analog Input Left / Right
2 • OUT L/R: Bypass Analog Output Left / Right. To check out how they work see page 20 ÷ 22 / 37 ÷ 42
3 • IN/OUT TO SLAVES: Analog Input and Output to control the amplifier in BRIDGE or CHAIN Mode
4 • DC OUT: 15 V supply for external devices
CONTROL BUS
5 • AC Link 1 and 2: RJ-12 terminals to connect other provided AC Link devices such as TH amplifiers, DRC
(Digital Remote Control), Audio Digital Processors, AC Link/USB Adapter for Personal Computer
connection. The use of connector 1 or 2 is interchangeable. The RJ-12 connectors provided cable is
normally used for digital telephone connection. It features 6-way connectors. The AC Link connection can
give power supply to the amplifier external devices.
6 • ADRS: ADRS: It’s the digital address of the amplifier when you want to realize a system with more than
one TH. Switch selector from 0 to 9 to set in a different number on each TH amplifier of the AC Link
network. Maximum allowed chain amplifiers number is 10. Warning: if the same number is set for two or
more amplifiers, the AC Link network does not work. The selected number is shown on Status display.
8
7
901
654
2
3
DIGITAL AUDIO
7 • AD Link: is an Audio Digital Bus that can carry 8 channels. It employs a Class 5 or 6 shielded Ethernet LAN
cable with the provided shielded connectors, normally used in computers network.
- AD Link IN: RJ-45 terminal input to connect digital audio coming from previous TH amplifier or the
provided external device AD Link such as Digital Audio Processor.
- AD Link OUT: RJ-45 terminal output to connect to the next TH amplifier.
8 • OPTICAL IN: Input to connect the provided optical cable with TOSLINK connectors. The optical audio
digital signal in S/PDIF standard is supplied from provided sources such as CD/DVD players. Accetta in
ingresso segnali stereo PCM fino a 192 kHz / 24 bit.
9 • REM IN/OUT: Turn On Remote Input and Output for other devices.
18
Autogood products internet store http://130.com.ua
Classic domain
3
1
OWNER’S MANUAL / TH uno
Front Panel
How to connect the remote
a
u
.
m
o
c
.
0
MEN U
DOW N
ENT ER
UP
PUSH
Hi :
Lo :
LEVEL
0.3 ÷ 1.2V
1.2 ÷ 4.8V RMS
RMS
BRIDG
CHAIN E
MASTE
R
3
1
0
180
PHAS
E
Rem
Out
Rem
In
Rem
In
L: 7 mm (5/16”)
MAX: 16 AWG
General
Rem Out
19
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
Front Panel
How to connect the source through the
preamplified analog input (standard mode)
TH configured in MASTER mode
Input:
Pre Out:
Power Output:
Stereo Analog
Stereo Analog
Mono Mix L+R
a
u
.
m
o
c
.
0
TH uno
Default preset
3
1
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
Stereo Pre In
Stereo Pre Out
REM In
8
7
901
654
2
3
Power Output: to carry out connections, check page 14 ÷ 16
DRC: not required
PRE OUT: To cascade-connect other amplifiers when using the analog input you MUST use
the Pre Out analog output.
20
Autogood products internet store http://130.com.ua
Classic domain
REM Out
OWNER’S MANUAL / TH uno
Front Panel
How to connect the source through the IN R
preamplified analog input (standard mode)
TH configured in MASTER mode
Input:
Pre Out:
Power Output:
Mono IN R Analog
Mono Analog = IN R
Mono = IN R
a
u
.
m
o
c
.
0
TH uno
Default preset
3
1
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
Mono Pre In
Mono Pre Out
REM In
8
7
901
654
2
3
Power Output: to carry out connections, check page 14 ÷ 16
DRC: not required
PRE OUT: To cascade-connect other amplifiers when using the analog input you MUST use
the Pre Out analog output.
21
Autogood products internet store http://130.com.ua
Classic domain
REM Out
OWNER’S MANUAL / TH uno
Front Panel
How to connect the source through the IN L
preamplified analog input (standard mode)
TH configured in MASTER mode
Input:
Pre Out:
Power Output:
Mono IN L Analog
Mono Analog = IN L
Mono = IN L
a
u
.
m
o
c
.
0
TH uno
Default preset
3
1
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
Mono Pre In
Mono Pre Out
REM In
8
7
901
654
2
3
Power Output: to carry out connections, check page 14 ÷ 16
DRC: not required
PRE OUT: To cascade-connect other amplifiers when using the analog input you MUST use
the Pre Out analog output.
22
Autogood products internet store http://130.com.ua
Classic domain
REM Out
OWNER’S MANUAL / TH uno
Electronic Crossover
Representing a high-end solution, the simplicity and power of the analog system found in the HV venti is thrust
forward again in the TH, making use of the amplifiers versatility.
The crossover ONLY acts on the amplifier power output, not on the PRE OUT output which is always a bypass.
The alignment is a Butterworth type as, when either of the TH amplifiers is set up in a mono configuration, the
slope of the filter can be set for 24 dB Oct operation.
Each TH uno is factory provided with:
- a TH-MXR.1 crossover board, containing the electronics required to set, through selectors, the operation
mode as well as the Low-Pass filter slope.
- eight crossover modules, featuring high-precision resistor packs corresponding to 32 cut-off frequencies
placed at equal distance from 18Hz thru 7,5kHz.
- two customisable crossover modules (to build them, see the “Custom Module” section in this manual).
a
u
.
m
o
c
.
0
Modules
Module position for active
cut-off frequency
Lo-pass module
Hi-pass module
3
1
Switch to set filter
operation mode
(Hi-pass, Lo-pass, Bandpass)
How to insert
the module
Switch to set Lo-pass
attenuation slope
(see page 25)
Classic domain
Frequency set modules: settable both in Hi-pass and Lo-pass mode
Custom Module
4.5 mm
Res (k7) =
n.7 resistor x 2 k7
5000
Freq (Hz)
9.5 mm
5000
2500
Example: Desired cut-off frequency = 2.5 kHz
= 2 k7
23
Autogood products internet store http://130.com.ua
Use 1 % tolerance 0.25 W resistors
OWNER’S MANUAL / TH uno
Electronic Crossover
Crossover Slope 12 dB (default configuration)
It is possible to set the crossover slope at 12 or 24 dB/Oct.
- The TH-MXR.1 board must be inserted;
- You need to operate on the ASC specific Setup Amplifier step. (See page 46).
Through the Status Monitor it is possible to check anytime the presence of the filter as well as the set slope.
TH uno
DO NOT INSERT
TH-MXR.1MODULE
PUSH
a
u
.
m
o
c
.
0
LEVEL
Hz
Hi :
Lo :
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
BRIDGE
CHAIN
MASTER
0 180
PHASE
12 dB
Hz
12 dB
180
Hz
Disabled
Hi-pass
12 dB
180
Disabled
24
Autogood products internet store http://130.com.ua
Lo-pass
12 dB
1.8k
Hz
Classic domain Digital domain
3
1
180
OWNER’S MANUAL / TH uno
Electronic Crossover
Crossover Slope 24 dB
If ASC is set at 24 dB Oct., it is anyway possible to set the crossover Low-pass at 12 or 24 dB Oct.
- The TH-MXR.1 board must be inserted;
- You need to operate on the TH-MXR.1 switch (see page 46). Through the Status Monitor it is possible to check
anytime the presence of the filter as well as the set slope.
TH uno
DO NOT INSERT
TH-MXR.1MODULE
a
u
.
m
o
c
.
0
PUSH
Hz
LEVEL
Hi :
Lo :
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
BRIDGE
CHAIN
MASTER
0 180
PHASE
24 dB
Hz
24 dB
12 dB
180
Hi-pass
24 dB
180
25
Autogood products internet store http://130.com.ua
Hz
Lo-pass
24 dB
1.8k
12 dB
Hz
Classic domain Digital domain
3
1
180
OWNER’S MANUAL / TH uno
Electronic Crossover
How to insert
Not inserted module
(default configuration)
TH uno
a
u
.
m
o
c
.
0
Hz
You can verify the crossover presence
by checking the ASC Status Monitor.
See page 53
3
1
Inserting module
PUSH
LEVEL
Hi :
Lo :
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
Hi-pass
12 dB
180
BRIDGE
CHAIN
MASTER
0 180
PHASE
Lo-pass
12 dB
1.8k
Hz
In this case you can verify both presence and slope of the crossover by
checking the ASC Status Monitor, however it is not possible to modify
its slope. See page 53.
26
Autogood products internet store http://130.com.ua
Classic domain
TH uno
OWNER’S MANUAL / TH uno
Example: TH amplifier on Subwoofer
Analog Input
Subwoofer
In order to build a Standard System
you have to:
SPEAKER B
-
1- Insert the TH-MXR.1 board with its relative
filter module;
2- Connect power supply;
3- Connect the subwoofer;
4- Connect signal inputs and remote turn on;
5- Select working mode on the Input
Controls Panel;
6- Adjust sensitivity on the Input Controls
Panel “LEVEL”;
12 V
- POWER +
-
+ CAP
Rear Panel
+
SPEAKER A
SS1
BRIDGE
CHAIN
MASTER
0 180
PHASE
3
1
Front Panel
Hi :
Lo :
In order to adjust the system
through the ACNet:
In questo sistema è necessario eseguire i
punti 1, 2, 3, 4, 5 e 7.
Il Software escluderà temporaneamente la
funzionalità del DRC per poter gestire tutte
le funzioni dell’amplificatore durante le fasi
di taratura e modifica, compresa la
regolazione della sensibilità d’ingresso con
tanto di rivelatore di picco.
654
8
7
901
2
3
PUSH
LEVEL
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
TH uno
7- Set ADRS on the Front Panel (in position 1
for instance);
8- Set Amp ID (on SUBWOOFER for
instance) in the ASC Setup Amplifier; this
way DRC will be enabled to adjust general
Volume, Balance and Fader.
USB / AC Link Converter
AC/Net (Optional use)
DRC (Optional use)
Source
Pre Out
REM Out
REMARK:
On ASC Dual Power and Runtime Monitor
will anyway stay active (by default) and
ready for changes (see page 47 and
following pages).
27
Autogood products internet store http://130.com.ua
Classic domain
SW1 or SW2
+
a
u
.
m
o
c
.
0
In order to add DRC to the System
you also need to:
OWNER’S MANUAL / TH uno
Subwoofer
Woofer
Tweeter
Example: Two Way + Sub, bi-amplified, TH amplifier
Analog Input
SPEAKER B
-
Passive Crossover
Hz
You have to follow
same steps as per
the above
example. The only difference is
for point 4, the second TH is a
TH uno (mono);
+
In order to add DRC to
the System you also
need to:
SPEAKER A
0 180
PHASE
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
Front Panel
In order to adjust the
system through the
ACNet:
901
ACNet (Optional use)
DRC (Optional use)
28
Autogood products internet store http://130.com.ua
USB / AC Link Converter
8
7
654
2
3
Hi :
Lo :
PUSH
LEVEL
TH uno
BRIDGE
CHAIN
MASTER
Rear Panel
+
Hz
Passive Crossover
Rear Panel
Front Panel
2
3
901
654
8
7
Pre Out
Source
7-Give the Front Panel ADRS of
each of the two amplifiers a
different setting (Example: 1
and 2);
8- Configure the Amp ID on the
ASC Setup Amplifier of the two
amplifiers by setting TH (1) as
Front and TH (2) as Sub;
9- Set the TH (1) ID Preout as
TH Amp, to let DRC adjust
general Volume, Balance,
Fader as well as Sub Volume.
Once the steps 1, 2,
3, 4, 5 and 7 have
been performed, the
Software will
temporarily bypass
the DRC in order to
manage in a more
direct and easier
way all of the system
functions.
REMARK:
On ASC Dual Power
and Runtime Monitor
will anyway stay
active (by default)
and ready for
changes (see page
47 and following
pages).
Classic domain
-
+ CAP
12 V
- POWER +
SW1 or SW2
SS1
SW1 or SW2
LEFT
CHANNEL
RIGHT
CHANNEL
a
u
.
m
o
c
.
0
3
1
REM Out
In order to build
a Standard
System:
R
L IN A
DC OUT
29
Autogood products internet store http://130.com.ua
654
901
2
3
8
7
8
7
654
2
3
2
3
901
654
901
ADRS
8
7
Classic domain
IN
OPTICAL
R
R
1 - AC Link - 2
L OUT A R
CONTROL BUS
L OUT A R
IN OUT
REM
Front Panel
Hi :
Lo :
PUSH
Front Panel
Front Panel
SW1 or SW2
mono
+ RIGHT -
A Channels
WM2 or WT1
+ LEFT -
Rear Panel
3
1
12 V
- POWER +
WM1 or WM2
+ CAP
WT2 or MT1
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
LEVEL
TH uno
BRIDGE
CHAIN
MASTER
Rear Panel
0 180
PHASE
Rear Panel
+
SPEAKER A
SS1
-
+ CAP
12 V
- POWER +
SW1 or SW2
+
SPEAKER B
-
+ RIGHT -
mono
+ LEFT -
B Channels
WT2 or MT1
a
u
.
m
o
c
.
0
USB / AC Link Converter
IN B
L IN B
DIGITAL AUDIO
L
OUT - AD Link - IN
R
IN A
L
+15 GND -15
ACNet (Optional use)
DRC (Optional use)
Source
Pre Out
REM Out
Subwoofer
Woofer
Tweeter
Midrange
OWNER’S MANUAL / TH uno
Example: Three Way + Sub, multi-amplified, TH amplifier
Analog Input
OWNER’S MANUAL / TH uno
Subwoofer
In order to build a
Standard System:
You have to follow same steps as
per the above example. The only
difference is that TH uno
becomes the audio chain first
amplifier, thus being able to
manage the whole system;
SPEAKER B
-
Passive Crossover
Hz
Woofer
Tweeter
Example: Two Way + Sub, bi-amplified,
with and without TH amplifiers.
Analog Input
+
a
u
.
m
o
c
.
0
7- Set ADRS on the Front Panel;
8- Set the Amp ID in the ASC
Setup Amplifier as Sub.
9- Set the ID Preout as Front, to
let DRC adjust general Volume,
Balance, Fader as well as Sub
Volume.
USB / AC Link Converter
ACNet (Optional use)
Front Panel
Once the above listed steps have
been performed, the Software
will temporarily bypass the DRC
in order to manage in a more
direct and easier way all of the
system functions.
654
2
3
REMARK: On ASC Dual Power
and Runtime Monitor will anyway
stay active (by default) and
ready for changes (see page 47
and following pages).
DRC (Optional use)
Rem OUT
Analog Source
Pre Out
8
7
901
In order to adjust the
system through the
ACNet:
30
Autogood products internet store http://130.com.ua
Classic domain
Rear Panel
0 180
PHASE
BRIDGE
CHAIN
MASTER
LEVEL
Rem IN
TH uno
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
Hi :
Lo :
PUSH
mono
mono
mono
PRE OUT
SPEAKER
LEFT
PRE IN
PRE IN
RIGHT
3
1
PRE OUT
SPEAKER
+
SPEAKER A
SS1
-
+ CAP
12 V
- POWER +
SW1 or SW2
In order to add DRC:
31
Autogood products internet store http://130.com.ua
Analog Source
Rem OUT
654
901
2
3
2
3
Classic domain
8
7
654
901
PRE OUT
LEFT
PRE IN
mono
PRE IN
RIGHT
PRE OUT
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
LEVEL
TH uno
BRIDGE
CHAIN
MASTER
USB / AC Link Converter
ACNet (Optional use)
Front Panel
Hi :
Lo :
PUSH
Front Panel
Rem IN
mono
SPEAKER
3
1
Rear Panel
0 180
PHASE
Rear Panel
+
SPEAKER A
-
SS1
SW1 or SW2
+ CAP
12 V
- POWER +
SW1 or SW2
WM1 or WM2
+
SPEAKER B
a
u
.
m
o
c
.
0
Pre Out
DRC (Optional use)
8
7
mono
SPEAKER
-
Passive Crossover
Woofer
Midrange
Subwoofer
Hz
Tweeter
OWNER’S MANUAL / TH uno
Example: Three Way + Sub, multi-amplified,
with and without TH amplifiers.
Analog Input
OWNER’S MANUAL / TH uno
THESIS
ASC (AMPLIFIER STATUS CONTROLLER)
The TH amplifiers ASC unit is the operational interface, programmed to control all of the amplifier’s functions.
The user can interact with the microprocessor which, without interfering with the sound, will provide control for
any possible adjustments. This manual section is especially thought for those who want to get the most of
these amplifiers exclusive features.
Some functions are automatic and transparent to the user, others require support during the installing,
adjusting or modifying phase. By accessing the ASC a set of menus will show, offering specific entries which
the user can operate on:
- Setup Amplifier:
Main Input: the user can decide what kind of source the amplifier has to drive;
Amp ID: the user can name the amplifier identifying the function the amplifier performs inside the system;
ID Preout: the user can name the pre-amplified section so it is possible to manage it inside the system;
X-Over Slope: the user can select the Low-bass filter slope (only in Mono mode);
Dual Power: the user can choose the sound quality and the power the amplifier has to work at;
a
u
.
m
o
c
.
0
- Status Monitor: the user can monitor the amplifier working status;
- Runtime Monitor: the user can select it on the Display to intermittently have information on the amplifier
status shown.
3
1
INPUTS AND PRE-AMPLIFIER
The TH amplifiers combine an analog and digital section in one device; keeping the two sections on separate
PCBs, although mounted within the same sub chassis.
Each amplifier features a state-of-the-art digital encoding section as well as a 24 bit 192 kHz converter. The
S/PDIF optical input accepts PCM stereo signals; also, the innovation consists in the fact the TH amplifier can
be driven in digital directly and, as a consequence, the whole system too, if a system in multi-amplification
configuration with the re-launch of this digital signal to other Thesis TH amplifiers through the AD Link system
(Audison Digital Link). Each amplifier independently takes care of the D/A conversion. While in the Digital Input
mode the DRC needs to be connected, so it works as an actual general volume and source selector control,
capable of repeating all the low frequency controls (Master Volume, Balance, Fader, Sub Volume).
The AD Link connectors on the TH input panel can receive the digital signal from sources or multi-channel
processors featuring the afore-mentioned outputs (Audison Bit One) and re-launching the digital signal to the
amplifiers chain through a Cat.5 certified shielded cable equipped with an RJ45 connector (provided).
In the following pages of this manual we will explain how to perform the amplifier setup and how to connect it in
all THESIS or mixed chains.
32
Autogood products internet store http://130.com.ua
Digital domain
Some of these functions need a remote control communicating with the microprocessor. Inside this manual,
where necessary, the presence of the DRC (Digital Remote Control) is underlined. The DRC also adds some
specific functions which you can read on their relative section from page 56 on.
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
Functions Description
2
3
TH uno
1
Default display
4
a
u
.
m
o
c
.
0
2 • MENU: this switch enables the ASC and shows the first available entry. Each time this switch is pushed
while the amplifier is normally working, the ASC displays the first available entry, not the last you worked on.
No matter which step of the management you are at, if you push the MENU button, you exit the ASC
management and you are automatically taken back to the first display screen (Default display) without
saving any changes.
Remark: No matter which step you are at of the management software, if you don’t operate on the switches for
5 seconds, the ASC automatically goes back to the first display screen (Default display) without saving any
changes.
3 • ENTER: this switch is to:
- confirm the selected entry,
- store it in the memory,
- move to the following menu entry.
The ASC performs these three activities automatically. If you modify the menu entry you are working on and
then you push “enter”, the display will show:
3
1
then the display will show the next entry. The changes will only be made once ENTER is pushed.
4 • UP - DOWN: through these switches the user can browse through the entries available inside the different
menus. According to the function you are checking, they allow you to modify your choice which, then, will
have to be confirmed by pushing ENTER.
33
Autogood products internet store http://130.com.ua
Digital domain
1 • TH due STATUS DISPLAY: it is the visual element of the ASC system, a back-lit two line 32 character LCD
display; While working, it can relate all of the configuration parameters memorised by the amplifier during
the installation, as well as the operational status of the amplifier.
The following pages address all the messages and information which from time to time the display can
show. In case of protection intervention, the state of protection is permanently displayed, until the problem
is resolved or until the amplifier is reset;
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
Setup Amplifier: Main Input
The first step to set the amplifier up is to select the main input the TH will use to get the signal. As soon as you
turn the amplifier on, the PRE analog input is selected by default. By changing this entry the user can also take
advantage of the other operational modes. From next time you turn the TH on, it will use the last selected entry.
If another input is used, the DRC is required. In that case, if for any reasons it is disconnected, all the setup
settings and low level controls will reset back to the default settings, unless the DRC is re-connected, in which
case they restore. (See page 35)
a
u
.
m
o
c
.
0
How to change: Main Input
TH uno
PUSH
3
1
MENU
ENTER
DOWN
DOWN
UP
Valore di Default
ENTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
BRIDGE
CHAIN
MASTER
0 180
PHASE
PRESS ENTER TO CONFIRM YOUR
SELECTION AND MOVE TO THE
NEXT SETUP
When this entry is selected, the amplifier can exclusively use the
pre-amplified input.
In multi-amplified systems, in order to cascade other amplifiers when using
the analog input, the Pre Out analog output MUST be used.
In this case, the amplifier can use the IN OPTICAL digital input or the
pre-amplified input. You can select either input only through the DRC.
DOWN
In multi-amplified systems, select this entry only on the first chain TH
amplifier, which is the one physically receiving the signal from the digital
source.
UP
In this case, the amplifier receives the input signal from another TH amplifier
through the AD Link digital connection.
DOWN
UP
In multi-amplified systems where both the analog and digital inputs are
connected, when moving from a source to another through the DRC, each
amplifier will automatically change input.
Select this entry when the amplifier is connected through the AD Link to a
system managed by an Audison external processor (such as the Bit One).
This entry gets active and is displayed only when the processor is
connected.
If for any reason the processor is disconnected with the amplifier on, the
ASC will go back to the default settings.
UP
34
Autogood products internet store http://130.com.ua
Digital domain
LEVEL
Hi :
Lo :
OWNER’S MANUAL / TH uno
Digital Inputs
How to adjust the volume control and input selector
using a digital source
In the following pages you will find examples of how to connect the TH to a system driven by head units using
the digital input. In order to use the TH IN OPTICAL digital input and therefore its D/A internal converter the
DRC Digital Remote Control MUST be connected to the TH amplifier.
The DRC will perform the function of selecting the head unit by selecting between Analog Input and Optical
Input, thus allowing the control of Main Volume, Subwoofer Volume, Balance and Fader.
a
u
.
m
o
c
.
0
3
1
DRC Vol: 00.0dB = TH MAX Power Output
Warning:
When using the optical digital input you have to use the DRC as main
volume control. If the DRC volume control is at 0 dB it equals to the
amplifier undistorted maximum output power.
To check all the functions and the DRC connection, see pages 56 ÷ 58
35
Autogood products internet store http://130.com.ua
Digital domain
If the last setup working conditions are no more valid, that is if you disconnect the DRC and you had changed
the default conditions, the ASC will automatically go back to use the PRE Analog Input. In this case Fader and
Balance will go back to central position, while general Volume and Sub Volume will go back to 0 dB (maximum
value). The TH display will show the following information:
OWNER’S MANUAL / TH uno
Front Panel
How to achieve same output volume level using an
analog source (with its own volume control) and
a digital source
Once you have adjusted the system, therefore once the amplifiers input sensitivity has been adjusted, you can
adjust the digital source volume level so that when selecting the analog or the digital source no difference in
sound is perceptible while listening. Once performed this adjustment, we would recommend that you use the
DRC volume control as general volume control.
On the DRC select the source: Optical Input
On the DRC adjust volume until you can read -30.0 dB
Insert the Test CD provided with the amplifier into the source connected to the digital input
Select track # 04 (sinusoidal signal 50 Hz / 0 dB)
Using a multimeter (True RMS) measure the voltage on the speaker terminals
On the DRC select the source: Analog Input
Do not change the set volume (-30.0 dB)
Insert the Test CD provided with the amplifier into the source connected to the digital input
Select track # 04 (sinusoidal signal 50 Hz / 0 dB)
Adjust the volume of the source connected to the analog input until, using a multimeter (True RMS),
you measure the same voltage on the speaker terminals
Use the DRC as main volume control
1-2)
3-4)
a
u
.
m
o
c
.
0
3
1
5)
X.X
VRMS
VAC
8-9)
10)
11)
X.X
VRMS
VAC
6-7)
X.X
VRMS
VAC
12)
36
Autogood products internet store http://130.com.ua
Digital domain
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
OWNER’S MANUAL / TH uno
Front Panel
How to connect a source through the optical digital
input in a system featuring more than one TH amplifier
TH configured in MASTER mode
Input:
Pre Out:
Power Output:
Digital Optical S/P DIF
Digital AD Link (Repeats the IN OPTICAL signal)
Mono
a
u
.
m
o
c
.
0
TH uno
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
AD Link Digital In
AC Link In
REM In
Digital (Optical) Out
REM Out
8
7
In this case the DRC is REQUIRED to:
- Adjust the general volume
- Select the optical input
901
654
2
3
PRE OUT:
anyway available, see page 38
37
Autogood products internet store http://130.com.ua
Digital domain
3
1
Setting changed
See page 34
OWNER’S MANUAL / TH uno
Front Panel
How to connect a source through an optical digital
input in a system featuring other non-TH amplifiers
TH configured in MASTER mode
Input:
Pre Out:
Power Output:
Digital Optical S/P DIF
Stereo Analog (R and L Ch of Digital Input)
Mono
a
u
.
m
o
c
.
0
TH uno
Setting changed
See page 34
LEVEL
Hi :
Lo :
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
BRIDGE
CHAIN
MASTER
0 180
PHASE
Stereo Pre In
Digital (Optical) Out
REM Out
REM In
8
7
901
654
2
3
In this case the DRC is REQUIRED in order to:
- Adjust general volume
- Select the optical input
PRE OUT:
see page 44 to check how to manage it
38
Autogood products internet store http://130.com.ua
In order to take advantage of
Volume control, Balance,
Fader and Sub through the
DRC also on the PRE output,
the AMP ID - Preout needs to
be set to the ASC Setup.
Digital domain
3
1
PUSH
OWNER’S MANUAL / TH uno
Front Panel
How to connect an analog and a digital source in
a system featuring more than one TH amplifier
TH configured in MASTER mode
Input:
Pre Out:
Power Output:
Analog/Digital Optical S/P DIF
Analog/Digital AD Link
Mono
a
u
.
m
o
c
.
0
TH uno
PUSH
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
AD Link Digital In
Stereo Pre In
Stereo Pre Out
AC Link In
REM In
Digital (Optical) Out
REM Out
8
7
In this case the DRC is REQUIRED to:
- Adjust general volume
- Select the optical input
901
654
2
3
PRE OUT:
anyway available, see page 40
39
Autogood products internet store http://130.com.ua
Digital domain
3
1
Setting changed
See page 34
OWNER’S MANUAL / TH uno
Front Panel
How to connect an analog and a digital source in
a system featuring other non-TH amplifiers
TH configured in MASTER mode
Input:
Pre Out:
Power Output:
Analog/Digital Optical S/P DIF
Stereo Analog
Mono
a
u
.
m
o
c
.
0
TH uno
Setting changed
See page 34
LEVEL
Hi :
Lo :
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
BRIDGE
CHAIN
MASTER
0 180
PHASE
Stereo Pre In
Stereo Pre Out
Digital (Optical) Out
REM Out
REM In
8
7
901
654
2
3
In this case the DRC is REQUIRED in order to:
- Ad just general volume
- Select the analog or digital optical input
PRE OUT:
see page 44 to check how to manage it
40
Autogood products internet store http://130.com.ua
In order to take advantage of
Volume control, Balance,
Fader and Sub through the
DRC also on the PRE output,
the AMP ID - Preout needs to
be set to the ASC Setup.
Digital domain
3
1
PUSH
OWNER’S MANUAL / TH uno
Front Panel
How to connect an analog and digital source in
a system featuring more than one TH amplifier
TH configured in MASTER mode
Input:
Pre Out:
Power Output:
IN R or IN L Analog/Digital Optical S/P DIF
Analog (=IN R or IN L) /Digital AD Link
In Analog: Mono (=IN R or IN L)
In Digital: Mono (=MIX L+R)
a
u
.
m
o
c
.
0
TH uno
Setting changed
See page 34
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
AD Link Digital In
Pre In
AC Link In
Digital (Optical) Out
REM Out
REM In
8
7
901
654
2
3
In this case the DRC is REQUIRED in order to:
- Adjust general volume
- Select the optical input
PRE OUT:
anyway available, see page 42
41
Autogood products internet store http://130.com.ua
Digital domain
3
1
Pre Out
PUSH
OWNER’S MANUAL / TH uno
Front Panel
How to connect an analog and a digital source in a
system featuring other non-TH amplifiers
TH configured in MASTER mode
Input:
Pre Out:
Power Output:
IN R or IN L Analog/Digital Optical S/P DIF
Analog (=IN R or IN L)
In Analog: Mono (=IN R or IN L)
In Digital: Mono (=MIX L+R)
a
u
.
m
o
c
.
0
TH uno
Setting changed
See page 34
LEVEL
Hi :
Lo :
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
0 180
PHASE
Pre In
Digital (Optical) Out
REM Out
REM In
8
7
901
654
2
3
In this case the DRC is REQUIRED in order to:
- Adjust general volume
- Select the optical input
PRE OUT:
See page 44, to check how to manage it.
42
Autogood products internet store http://130.com.ua
In order to take advantage of
Volume control, Balance,
Fader and Sub through the
DRC also on the PRE output,
the AMP ID - Preout needs to
be set to the ASC Setup.
Digital domain
3
1
Pre Out
PUSH
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
Setup Amplifier: Amp ID
AMP ID stands for Amplifier IDentification. The AMP ID is a way to identify the task the amplifier performs inside
the system. The AMP ID does not affect the electric functioning and does not act on the amplifier electronic
crossover. The AMP ID is fundamental to adjust Volume, Balance, Fader as well as Sub Volume when the DRC
is connected. The ASC recognises the function the amplifier has been given through the ID. By acting on the
DRC and adjusting Volume, Balance, Fader as well as Sub Volume, as a consequence also the signal to the
amplifiers will be managed.
Example:
If the AMP ID-Front is assigned to the TH amplifier, by operating on the DRC its general volume, as well as the
right/left balance, will change. Also, by setting the Fader on Rear you will hear the volume diminishing;
however, no change will be perceived if you operate on the DRC Sub volume.
Vice versa, if the AMP ID – Subwoofer is assigned to the TH amplifier, by operating on the DRC its general
volume, more specifically the Sub volume, will change; however, no change will be perceived if you operate on
the right/left balance or moving the Fader.
a
u
.
m
o
c
.
0
In order to avoid errors, you should assign the ID according to the speakers connected to the amplifier.
3
1
MENU
PUSH
LEVEL
Hi :
Lo :
PRESS
ENTER TO
REACH
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
ENTER
BRIDGE
CHAIN
MASTER
0 180
PHASE
PRESS ENTER TO CONFIRM YOUR
SELECTION AND MOVE TO THE
NEXT SETUP
DOWN
DOWN
UP
DOWN
UP
DOWN
UP
Default Entries
UP
43
Autogood products internet store http://130.com.ua
Digital domain
TH uno
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
Setup Amplifier: Amp ID-Preout
The AMP ID can also be assigned to the PRE OUT output. This function is extremely useful in case the TH
amplifier is added to a pre-existing system featuring not only TH amplifiers or if you want to add to the TH
system a non-TH amplifier. This way you can anyway know the non-TH amplifier function as well as adjust its
volume. The AMP ID - Preout provides the ability to expand the system endlessly, keeping the low level
parameters management functions through the DRC.
As the AMP ID – Preout does not operate on the electronic crossover, it does not put in any filters on the output
signal! The signal on the PRE OUT output will always be exactly the same as the one on the selected input.
a
u
.
m
o
c
.
0
TH uno
PUSH
LEVEL
Hi :
Lo :
3
1
PRESS
ENTER TO
REACH
DOWN
UP
ENTER
ENTER
0 180
PHASE
PRESS ENTER TO CONFIRM YOUR
SELECTION AND MOVE TO THE
NEXT SETUP
DOWN
DOWN
UP
Default Entries
1
DOWN
UP
UP
1
44
Autogood products internet store http://130.com.ua
Warning: if a TH amplifier
already connected with the
AD Link is connected to the
analog Preout output , THIS
OPTION IS MANDATORY, as
the second TH amplifier will
already have its own AMP ID.
Digital domain
MENU
BRIDGE
CHAIN
MASTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
OWNER’S MANUAL / TH uno
Front Panel
How to adjust the PRE OUT analog output
As already said, the AMP ID can also be assigned to the PRE OUT output, but not only to it. Through the
ACNet software also the PRE OUT sensitivity can be adjusted to align the gain of the amplifier connected to
that output, thus adapting sensitivity according to the system general volume increase and decrease.
The procedure to perform this operation is the following:
1- Connect the (non-TH) amplifier to the PRE output.
2- Assign the ID - Preout.
3- Set the non-TH amplifier sensitivity to the minimum.
4- Through the AC Net slider, increase the output sensitivity until you get the desired volume.
5- Should it not be enough, increase the non-TH amplifier input sensitivity
a
u
.
m
o
c
.
0
PRESS
TH uno
901
654
2
3
PRESS
TH uno
3
1
8
7
UP TO
UP TO
PRESS
TH uno
MIN
45
Autogood products internet store http://130.com.ua
Digital domain
PRESS
TH uno
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
Setup Amplifier : X-Over Slope
You can choose the crossover filter slope.
Select 1- 12 dB/oct: in this case, the Low-pass slope switch on the TH-MXR module will not be active.
Select 2- 24 dB/oct: when this option is selected, the Low-pass slope switch on the TH-MXR module will
anyway be active, thus providing the ability to mechanically choosing between 12 and 24 dB/oct.
For further information see page 23 ÷ 26
a
u
.
m
o
c
.
0
TH uno
PUSH
3
1
MENU
ENTER
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
ENTER
PRESS
ENTER TO
REACH
0 180
PHASE
PRESS ENTER TO CONFIRM YOUR
SELECTION AND MOVE TO THE
NEXT SETUP
DOWN
DOWN
UP
UP
Default Value
DOWN
BRIDGE
CHAIN
MASTER
UP
DOWN
UP
46
Autogood products internet store http://130.com.ua
Digital domain
LEVEL
Hi :
Lo :
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
DUAL POWER & BIAS CONTROL
A revolutionary function called Dual Power was introduced for the first time in the HV venti.
Controlling the amplifier’s output power configuration, this function allowed the predetermination of the
amplifiers output power and of the grade of the outputs operational class. The digital interface enables
expedient intervention by the user, setting up the amplifier’s operational modes by operating on the power and
bias current settings, all in real-time. In any case the result is a clear “sound customisation”.
In this Setup section you can set the amplifier operational mode.
There are four possible presets:
Class A: to intensify the musical performance; you can not expect the amplifier to drive loads under 4 Ω
under these conditions;
Hi-AB Class: it is the default mode, combining the characteristics of high class functioning, great capability
of driving difficult loads and high power.
Hi-Current: Pure power, on any loads
Energy Saving: it sets the power emission to the minimum, allowing musical enjoyment for extended
periods of time with the vehicles engine off.
a
u
.
m
o
c
.
0
3
1
Setup Amplifier: DUAL POWER Settings
TH uno
PUSH
LEVEL
Hi :
Lo :
MENU
ENTER
PRESS
ENTER TO
REACH
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
ENTER
TO EXIT
ENTER
BRIDGE
CHAIN
MASTER
0 180
PHASE
PRESS ENTER TO CONFIRM YOUR
SELECTION AND MOVE TO THE
NEXT SETUP
DOWN
DOWN
UP
DOWN
UP
UP
Default Value
DOWN
UP
When changing mode, you need to wait a few seconds to
perceive the acoustic changes.
47
Autogood products internet store http://130.com.ua
Digital domain
When changing mode, you have to wait a few seconds to perceive the acoustic variations. The Dual Power is
absolutely indipendent from the other settings selections. It will work both in Mono and in Stereo configurations, both with and without the crossover, both connecting a subwoofer and a tweeter to it. So we recommend
you pay attention to select a functioning mode accepting the impedance load you applied to the amplifier.
Check the following page for comparative charts with reference values. WARNING: Using two TH uno in
BRIDGE mode, you must setup both with the same Dual Power setting.
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
DUAL POWER Values
850 W
Power Output
RMS W
850 W
a
u
.
m
o
c
.
0
200 W
200 W
3
1
30 mA
10 mA
4 mA
8.5 A
Load
Impedance
Idling Current
Consumption
6.2 A
4.3 A
2.2 A
1Ω
1Ω
2Ω
2Ω
2Ω
4Ω
4Ω
4Ω
48
Autogood products internet store http://130.com.ua
4Ω
Digital domain
Bias Regulation
A Class
100 mA
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
Setup Amplifier: DUAL POWER Settings
How to change presets on the Memory (DRC required)
The TH due can be set with only one operational mode at a time, while the DRC can manage four customisable
memories.
1- Default: In standard configuration, without making any changes, if memory 1 is recalled from the DRC, all the
TH amplifiers connected to the system will be working in Hi-AB Class mode (as it is the default setting), while
selecting memory 2 they will be workin in Hi-Current mode and so on.
a
u
.
m
o
c
.
0
3
1
PRESS
PRESS
PRESS
TH uno
PRESS
TH uno
PRESS
UP TO
TH uno
PRESS
TH uno
Example: In a three-way + Sub system, multi-amplified with TH quattro on TW and MID, TH due on WF and
TH uno on SUB, in default setting if you recall memory 1 all of the TH’s would work in Hi-AB Class mode. It is
possible to create custom memories, see for instance the example below, to store in memory 1 a system
especially designed to ensure top quality for each way or to store in memory 2 a system especially designed
for the best power/quality ratio, to store in memory 3 a system set to obtain maximum quality and in memory 4
a system best optimizing the current consumption.
Default configuration
1
DRC Memory
2
3
Modified configuration
4
Hi-AB Class Hi-Current
A Class Energy Saving
Hi-AB Class Hi-Current
A Class Energy Saving
Hi-AB Class Hi-Current
A Class Energy Saving
1
A Class
DRC Memory
2
49
Autogood products internet store http://130.com.ua
4
Hi-AB Class A Class Energy Saving
Hi-AB Class Hi-Current
Hi-Current
3
Hi-Current
A Class Energy Saving
A Class Energy Saving
Digital domain
2- Customizing: by acting on both the DRC memories and the ASC control panel of the amplifier, you can create
custom setups. For instance, if you want the TH amplifiers to anyway work in A-Class mode, you will have to act
on the setup as follows:
- Select memory 1 on the DRC by pressing first SEL and then 1
- Select the A-Class preset on the ASC by accessing to its corresponding setup
- Repeat this operation for each DRC memory
- Repeat this operation for each TH present in the system
IN
OPTICAL
R
R
654
901
2
3
50
Autogood products internet store http://130.com.ua
8
7
8
7
654
2
3
2
3
901
654
901
ADRS
8
7
IN OUT
REM
Front Panel
Hi :
Lo :
PUSH
Front Panel
Front Panel
Rear Panel
+ RIGHT -
SW1 or SW2
mono
+ LEFT -
A Channels
WM2 or WT1
12 V
- POWER +
WM1 or WM2
+ CAP
WT2 or MT1
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
LEVEL
TH uno
BRIDGE
CHAIN
MASTER
Rear Panel
0 180
PHASE
Rear Panel
+
SPEAKER A
SS1
-
+ CAP
12 V
- POWER +
SW1 or SW2
+
SPEAKER B
-
+ RIGHT -
mono
+ LEFT -
B Channels
WT2 or MT1
a
u
.
m
o
c
.
0
Digital domain
1 - AC Link - 2
L OUT A R
CONTROL BUS
L OUT A R
3
1
USB / AC Link Converter
IN B
L IN B
DIGITAL AUDIO
L
OUT - AD Link - IN
R
L IN A
DC OUT
+15 GND -15
R
IN A
L
Digital (Optical) Out
ACNet (Optional use)
DRC (Necessary)
Function:
Master Volume
Source
REM Out
Subwoofer
Woofer
Tweeter
Midrange
OWNER’S MANUAL / TH uno
Example: Three Way + Sub, multi-amplified, TH amplifiers
Digital Input
51
Autogood products internet store http://130.com.ua
USB / AC Link Converter
IN B
R
R
IN
OPTICAL
L IN B
DIGITAL AUDIO
L
OUT - AD Link - IN
R
L IN A
DC OUT
+15 GND -15
R
IN A
L
654
901
2
3
8
7
8
7
654
2
3
2
3
901
654
901
ADRS
8
7
IN OUT
REM
Front Panel
Hi :
Lo :
PUSH
Front Panel
Front Panel
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
LEVEL
TH uno
Digital domain
1 - AC Link - 2
L OUT A R
CONTROL BUS
L OUT A R
Digital (Optical) Out
REM Out
3
1
+ RIGHT -
BRIDGE
CHAIN
MASTER
Rear Panel
0 180
PHASE
Rear Panel
Rear Panel
+
SPEAKER A
-
SS1
SW1 or SW2
mono
+ LEFT -
A Channels
WM2 or WT1
12 V
- POWER +
WM1 or WM2
+ CAP
WT2 or MT1
+ CAP
12 V
- POWER +
SW1 or SW2
+
SPEAKER B
-
+ RIGHT -
mono
+ LEFT -
B Channels
WT2 or MT1
a
u
.
m
o
c
.
0
ACNet (Optional use)
DRC (Necessary)
Function:
Source Selector
(Analog IN / Optical IN)
Master Volume (On Optical)
Digital Source
Analog Source
Pre Out
Subwoofer
Woofer
Tweeter
Midrange
OWNER’S MANUAL / TH uno
Example: Three Way + Sub, multi-amplified, TH amplifiers
Analog + Digital Input
52
Autogood products internet store http://130.com.ua
654
2
3
PRE IN
mono
PRE IN
RIGHT
BRIDGE
CHAIN
MASTER
Rear Panel
0 180
PHASE
Rear Panel
USB / AC Link Converter
ACNet (Optional use)
0.3 ÷ 1.2V RMS
1.2 ÷ 4.8V RMS
LEVEL
TH uno
Digital domain
Front Panel
Hi :
Lo :
PUSH
Front Panel
mono
SPEAKER
Rem IN
PRE OUT
+
SPEAKER A
-
SS1
SW1 or SW2
+ CAP
12 V
- POWER +
SW1 or SW2
WM1 or WM2
+
SPEAKER B
a
u
.
m
o
c
.
0
Digital Source
Digital (Optical) Out
Pre Out
8
7
2
3
901
654
901
PRE OUT
LEFT
3
1
Analog Source
DRC (Necessary)
Function:
Source Selector
(Analog IN / Optical IN)
Master Volume (On Optical)
8
7
mono
SPEAKER
-
Passive Crossover
Woofer
Midrange
Subwoofer
Hz
Tweeter
OWNER’S MANUAL / TH uno
Example: Three Way + Sub, multi-amplified,
with both TH and non-TH amplifiers.
Analog + Digital Input
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
Status Monitor
This feature of the ASC provides the ability to monitor the amplifier working status by moving through the
different entries the data regarding the working TH amplifier will show. When displaying a value, if you do not
act on any of the buttons for 5 seconds, the ASC automatically goes back to the default display screen.
a
u
.
m
o
c
.
0
MENU
DOWN
UP
ENTER
TO EXIT
ENTER
Displays the voltage measured on the amplifier power supply terminals.
DOWN
Displays the working temperature measured on the heat sink internal surface
3
1
UP
DOWN
UP
Displays the amplifier Mode (the selected Dual Power preset )
Displays the amplifier function inside the system, identified by its own ID.
Displays the amplifier PRE output function inside the system, identified by its
specific ID.
These functions are only customisable if the PC is connected through the
ACNet software.
These entries are displayed on the Status Monitor only if customized.
Displays the input sensitivity range and value measured in volts, both being
adjusted by the relative potentiometer on the INPUT PANEL or by the ACNet
software.
Displays the PRE output sensitivity range and value measured in volts, both
being adjusted exclusively by the ACNet sofware.
Displays the main input type selected on the amplifier.
Displays the filter slope pre-set during the amplifier Setup.
Indicates whether the amplifier is set to work in stereo or mono configuration.
Displays the value of the amplifier digital address selected in the ADRS
specific selector located on the FRONT PANEL.
Displays the amplifier serial number.
The user can not modify this field in any way.
UP
Displays the version of the installed ASC software.
53
Autogood products internet store http://130.com.ua
Digital domain
DOWN
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
Runtime Monitor
This function of the ASC provides the ability to alternately show on the amplifier display the information on its
operational status. Through this setup you can select the fields you want to be visibile when the amplifier is on.
For each field you can select YES to have the entry show on the display. If all NO are selected, the display will
always show the default display screen. You will only have to select even just one entry to see it appear
alternately on the display while the amplifier is working. By default all the fields are pre-set on NO.
MENU
a
u
.
m
o
c
.
0
DOWN
UP
UP
ENTER
DOWN
DOWN
UP
3
1
UP
ENTER
TO EXIT
54
Autogood products internet store http://130.com.ua
Digital domain
ENTER
DOWN
OWNER’S MANUAL / TH uno
ASC - Amplifier Status Controller
Info and Alert sentences
Amp in default
2
Amp in muting
3
Amp in muting
4
Amp off
5
Autoreset
6
Event’s alert
7
Event’s alert
8
Autoreset
9
Event’s alert
10
Autoreset
11
Event’s alert
What it means
The previously found connection with DRC has been lost. This information is
also displayed when the amplifier is on and the DRC gets disconnected.
Volume goes back to 0 dB (the set sensitivity is not modified). Balance and
Fader are set back to their centre position (0). The Sub volume is set back to
0 dB. The ANALOG input is automatically selected.
MONO-STEREO switch position is different from the original position
acquired during the Amplifier Setup (STEREO).
You have to access to the ASC and at least set the AMP ID.
a
u
.
m
o
c
.
0
MONO-STEREO switch position is different from the original position
acquired during the Amplifier Setup (MONO).
You have to access to the ASC and at least set the AMP ID.
General protection.
The amplifier will try to restart 5 times.
Contact Audison Technical Support.
Overload protection.
Check speaker load. This message
is displayed when an overload occurs.
Rare overload occurs. Check speaker load.
This message is displayed when an overload has already
occurred but the amplifier restarted.
3
1
Output is reaching distortion threshold. The information is immediate and
stays displayed only while distortion is still present.
Thermal protection. Check environmental temperature
and/or use a low bias Dual Power setting.
Rare thermal protection occurs. Check environmental temperature
and/or use a low bias Dual Power setting.
Contact with ground. Stop listening and check speaker cables.
Digital domain
1
What the display
is showing
Rare contact with ground occurs.
Stop listening and check speaker cables.
These messages appear also on the DRC display.
The DRC will display amplifier name and ADRS on the first row.
55
Autogood products internet store http://130.com.ua
General
What the TH
is doing
OWNER’S MANUAL / TH uno
DRC - Digital Remote Control
(not included with TH amplifier)
The DRC is a microprocessor digital system providing remote control and monitoring of the TH amplifiers.
Once connected it performs important functions such as:
- Source selection (it also provides the ability to use the optical digital input as main source, checking its
main volume)
- Main volume control
- Subwoofer volume control
- Right/ left balance control
- Front/rear Fader control
- Dual Power working memory Manager
- Status Monitor for all the amplifiers in the system
a
u
.
m
o
c
.
0
TURN
Default display
Volume control
Default Function
3
1
2
3
4
Main screen
1
2
PRESS
PRESS
SEL
Select the Input.
This option is
only available if
Digital Main
Input is selected
on the TH amp.
3
4
Recalls Dual Power Memory
1
Dual Power
Memory 1
2
Dual Power
Memory 2
3
Dual Power
Memory 3
4
Dual Power
Memory 4
SEL
Digital domain
1
When recalling a memory,
the display shows its
corresponding preset stored
in the amplifier.
Selects and shows, as a sequence,
the Status Monitor fields.
1
Amplifier Status Monitor
PREVIOUS PARAMETER
2
Amplifier Status Monitor
NEXT PARAMETER
If more than one TH amps are connected, it
selects and shows, as a sequence, the
different amplifiers, identified by the ADRS.
SEL
3
Amplifier Status Monitor
PREVIOUS AMPLIFIER
4
Amplifier Status Monitor
NEXT AMPLIFIER
Main screen
When you select a
parameter you want to
display, the display
alternates it to the main
display screen.
To exit this view press SEL.
56
Autogood products internet store http://130.com.ua
General
PRESS
OWNER’S MANUAL / TH uno
DRC - Digital Remote Control
Info and Alert sentences
AMPLIFIER ADDRESS
(ADRS)
TH AMPLIFIER
MODEL
a
u
.
m
o
c
.
0
PROTECTION
TYPE
Service general protection.
Call Audison Technical Support.
Event’s alert
Autoreset
Autoreset
Event’s alert
3
1
Overload protection.
Check speaker load.
Clip output is reaching distortion threshold.
Thermal protection. Check environmental temperature
and/or use a low bias AMC setting.
Rare contact with ground occurs.
Stop listening and check speaker cables.
The PC is connected and ACNet software is running.
The DRC is disabled.
General
Autoreset
Digital domain
Amp off
57
Autogood products internet store http://130.com.ua
OWNER’S MANUAL / TH uno
DRC - Digital Remote Control
DRC - How to connect
a
u
.
m
o
c
.
0
8
7
901
654
2
3
DRC/AC Link cable (provided)
DRC - How to install
6 mm / 0.23”
16 mm / 0.63”
17 mm / 0.67”
90 mm / 3.54”
12.5 mm / 0.49”
43.5 mm / 1.71”
13.5 mm / 0.53”
External mounting
58
Autogood products internet store http://130.com.ua
General
3.5 mm / 0.14”
50 mm / 2”
Flush mounting
Ø 2 mm / 1/8”
68 mm / 2.68”
35 mm / 1.38”
Digital domain
3
1
OWNER’S MANUAL / TH uno
ACNet - Audison Control Network
Software to control Audison amplifier
a
u
.
m
o
c
.
0
3
1
8
7
901
654
Digital domain
Hardware Requirements:
1024x768 Display Optimized - 96 dpi Font size - 1 x USB port (1.1 compliant)
2
3
RJ12 (Provided)
1 - Switch on the PC
2 - Switch on the amplifier
3 - Connect AC Link with RJ-12 cable
4 - Connect USB cable from USB/AC Link
converter to PC
5 - Wait 5/10 s, the PC recognize
the USB connection
6 - Launch the software
7 - If everything it’s OK the PC monitor
displays the complete software page.
Rear Panel
USB/AC Link
(Provided)
Front Panel
USB (Provided)
59
Autogood products internet store http://130.com.ua
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
Functions Description
8
10
9
2
6
3
3
1
7
4
1 • SYSTEM DISPLAY:
TH amplifiers connected to the system with AC Link will be displayed in this area. If the ADRS are set correctly,
this display will show the TH amplifier model name and its ADRS. If more than one amplifier is set on the
system with the same ADRS, the software will only show and allow to tune the first one.
2 • IDENTIFICATION: This area shows report boxes and active fields, which enable the identification of each
single amplifier.
3 • INPUTS: In this section it’s possible to adjust each feature relating to the TH amplifier inputs
4 • DUAL POWER MEMORY: This menus allow the function setting for each amplifier separately.
5 • SYSTEM AUDIO CONTROL: The sliders in this area operate on the low level audio controls of the whole
system.
6 / 7 • AMPLIFIER STATUS: This section is the real monitor of the amplifier’s vital functions.
8 • SYSTEM AMPLITUDE SETUP: This function enables the input sensitivity of the amplifiers in the system.
9 • SYSTEM DUAL POWER SETUP: This function enables the function setting of all the amplifiers in the
system.
10 • SYSTEM SETUP LOAD/SAVE: It guarantees the saving of the whole system setup or the loading of
setups previously saved.
60
Autogood products internet store http://130.com.ua
Digital domain
1
a
u
.
m
o
c
.
0
5
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
System Display
8
10
9
2
5
6
3
1
7
a
u
.
m
o
c
.
0
3
1
When installing a system composed by TH amplifiers it’s possible to create a network between them by using
AC Link series connection.
It‘s necessary that a unique ADRS is given to each amplifier. Each amplifier must have a different ADRS.
In this way, when the software is turned on, the system will be able to automatically recognize which amplifier is
present in the network.
This display will show all the “linked” amplifiers creating an icon corresponding to the model, the model name
and the ADRS set during the installation.
The ACNet software allows the user to work either on one single amplifier or on the whole system.
In order to understand the use of the software we will work on a three way system + sub, multi-amplified, using
a TH quattro on Tweeter and Midrange, TH due on Woofer and TH uno on Subwoofer.
For example, to work on a TH due double click on its dedicated icon. The name will be highlighted and its
corresponding data will be displayed in the specific fields.
61
Autogood products internet store http://130.com.ua
Digital domain
4
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
Amplifier Setting: Identification
8
10
9
2
5
6
3
1
7
4
a
u
.
m
o
c
.
0
3
1
The drop-down menu displays the available values to be assigned to the amplifier depending on its
configuration / functioning modes.
For example, if the amplifier it’s mono set, the available ID will be the specific ones for the mono setting.
If the system is also composed by non-TH amplifiers, they can be managed by attributing an ID to the Pre Out
connected to them. The menu default option is “TH AMP”, because generally a TH amp (provided with its
specific Amp ID already) is connected to the Pre Out.
62
Autogood products internet store http://130.com.ua
Digital domain
The amplifier identification provides its S/N - serial number (fixed), the owner name (free-text), the installer
name (free-text) and the Firmware release included in the microprocessor inside the TH amplifier.
The ACNet area shows the amplifier configuration (mechanically set in the TH Input Panel) and allows the Amp
ID and AmpPreout setting through a drop-down menu.
The report boxes on the right confirm if any crossover modules have been used inside the amplifier and which
slope setting has been given.
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
Amplifier Setting: Inputs
8
10
9
2
5
6
3
1
7
a
u
.
m
o
c
.
0
As for the ASC Setup Amplifier, it is necessary to set the system whenever wanting to use the digital input.
In this area it is necessary to select the Main Signal Input for each amplifier connected to the system
Example:
- If the amplifier being set is the first of the network to receive the signal from an external source, it is
necessary to specify if it is an analog or digital one, by selecting Analog or Optical Master.
- If it is connected to both an analog and a digital source, select Optical Master and manage the sources
switch through the DRC.
- If the amplifier being set receives the signal from another TH amp, connected in analog and digital AD Link,
select Optical Slave .
- If the amplifier being set receives the signal from an external audio processor (Ex: Audison Bit One) select
AD Link.
3
1
The note warns that if the DRC is not connected to the system, even selecting a digital input, when ACNet
software will be switched off, only the Analog Input will operate.
63
Autogood products internet store http://130.com.ua
Digital domain
4
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
Amplifier Setting: Sensitivity and Preout Level
8
10
9
2
5
6
3
1
7
a
u
.
m
o
c
.
0
From this section featuring drop down menus, it is possible to regulate each amplifier’s input sensitivity, acting
also on the High/Low Level.
There are sliders for each channel which can work singularly or together if “linked”. The software enables the
fine tuning between right and left, acting on the corresponding slider. The software will show the level
measured in V.
The LED Clip flashes when the max level is reached during tuning or playing.
3
1
When using a non-TH amplifier to be controlled by DRC, an ID must be assigned to the Pre Out where it is
connected. In this way it is still possible to manage the TH Preout sensitivity.
The specific sliders will come into view only when a name which is not TH Amp is given to the active field.
64
Autogood products internet store http://130.com.ua
Digital domain
4
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
Amplifier Setting: Dual Power Memory
8
10
9
2
5
6
3
1
7
a
u
.
m
o
c
.
0
3
1
In this section the TH amps operating modes memories can be selected.
The availabIe preset are: Hi-AB Class (default), Hi-Current, A-Class, Energy Saving. They can be assigned to
each single memory by using the drop down menus.
The memories can be recalled through the Memory keys 1 / 2 / 3 / 4 but when ACNet software is switched off,
if the DRC is not connected to the system, the function selected on Memory 1 will be operating.
TH uno and TH due can only work with one preset, while TH quattro can work with one preset on A Channels
and one on B Channels.
Note: When the preset A-Class or Energy Saving is assigned to A Channels, this will be automatically applied
to B Channels. Please refer to the following table:
65
Autogood products internet store http://130.com.ua
Digital domain
4
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
System Audio Control
8
10
9
2
5
6
3
1
7
a
u
.
m
o
c
.
0
3
1
These controls act on the whole system:
- System Volume: it’s the main volume control of the system, the slider on Min position switches on the
muting and shows “MUTE” in the specific box. The adjustment starts from -60 dB (muting) up to 0 dB Max,
0,5 dB steps.
- Sub Volume: it’s the specific volume control for the subwoofer, the slider on Min position switches on the
muting and shows “MUTE” in the specific box. The adjustment starts from -12 dB (muting) up to +6 dB
Max, 0,5 dB steps.
- Balance: it‘s the control that allows the left and right balancing. When in central position (+0) the output
volume between left and right it’s identical. It‘s possible to unbalance the output volume of one channel
compared to the other.
- Fader: t‘s the control that allows the Front and Rear balancing. When in central position (+0) the output
volume between Front and Rear it’s identical. It‘s possible to unbalance the output volume of one zone
compared to the other.
The Amp ID of each single amplifier inside the system must be set correctly in order to operate the audio
controls. The Sub Volume control, for example, will only operate on the amplifiers identified on the Amp ID
as Subwoofer. The Balance control will operate on all the amplifiers characterized by the presence of a right
and left channel (it will not operate on Central and Subwoofer).
The note warns that if the DRC is not connected to the system, when ACNet software is switched off, these
controls will not operate.
66
Autogood products internet store http://130.com.ua
Digital domain
4
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
Amplifier Status
8
10
9
2
5
6
3
1
7
a
u
.
m
o
c
.
0
3
1
The ACNet software performs a real-time check-up of the amplifiers operating conditions.
Once an amplifier is selected, the parameters monitored by the ASC microprocessor are shown on the specific
boxes.
Bias and Power
- User preset: displays the operating modes selected in the Dual Power Setting. For the TH quattro the
operating modes of both channels A and B are shown.
- Bias: displays the bias current value corresponding to the preset in use.
- Power Supply: displays the power supply value corresponding to the preset in use.
Hardware Monitor
- Supply Voltage: displays the power supply voltage (V) measured on the amplifier terminals.
- Temperature: displays the amplifier working temperature measured in °C.
- Protections: the protection conditions are provided for each channel.
Overload: warns when an extremely low load has been connected to the amplifier speaker terminals
or when a temporary overload has occurred;
Service: warns when DC current is coming out of the speaker terminals;
Speakers: warns when a short-circuit has occurred in the connection between amplifier and speakers;
Ov. Temperature: warns when an operating temperature, dangerous for the amplifier, has been
reached.
67
Autogood products internet store http://130.com.ua
Digital domain
4
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
System Amplitude Setup
8
10
9
2
5
6
3
1
7
a
u
.
m
o
c
.
0
Once each single amplifier in the system has been set, it is possible to use the setup window above, which
allows the sensitivity adjustment of all amplifiers of the entire system.
Using this section, it’s possible to operate in an even mode on the amplifiers level tuning.
Sliders will work singularly on each amplifier and, selecting the Output Level LINK key, it’s possible to tie all the
sliders together and modify the main system level. The LED Clip flashes, when the max level is reached
during tuning or playing.
3
1
Single level adjustment
Whole system level adjustment
68
Autogood products internet store http://130.com.ua
Digital domain
4
ADVANCED MANUAL / ACNet
ACNet - Audison Control Network
System Dual Power Setup
8
10
9
2
5
6
3
1
7
a
u
.
m
o
c
.
0
This setup enables the complete management of the operating mode of the amplifiers in the systems. The
chart above presents in one window all the amplifier names and channels being used.
The fields are provided by default as in the example above. When wanting to achieve peculiar operating
modes, depending on the acoustics results requested to the system, it is possible to modify the preset
sequence.
Examples:
- To achieve the best quality/performance ratio system, select A-Class for TH quattro, Hi-AB Class for TH due
and Hi-Current for TH uno.
- To achieve the best power/performance ratio system, select Hi-AB Class for TH quattro, Hi-Current for TH
due and Hi-Current for TH uno.
- To achieve the highest audio quality system, use Memory 3.
- To achieve an unextended listening time while the car is parked, use Memory 4.
3
1
69
Autogood products internet store http://130.com.ua
Digital domain
4
OWNER’S MANUAL / TH uno
Technical Specifications
Power supply
Voltage
Idling current:
A-Class
Hi-AB Class
Hi-Current
Energy Saving
Switched off
11 ÷ 15 VDC
8.5 A
6.2 A
4.3 A
2.2 A
0.04 mA
Consumption @ 14.4 VDC, 1 7 Max musical power
Remote IN voltage
Remote OUT voltage
Internal fuse (AFS)
132 A
7 ÷ 15 VDC (1 mA)
12 VDC (50 mA)
150 A
a
u
.
m
o
c
.
0
Amplifier stage
Distortion - THD @ 1 kHz, 4 7, 90% Power
Bandwidth @ -3 dB, 2 VRMS, 4 7
S/N ratio @ A weighted, 1 V, Max Power
Damping factor @ 1 kHz, 2 VRMS, 4 7
Input sensitivity (two ranges)
Input impedance (PRE IN)
Load impedance (Min @ Dual Power Mode - Hi-Current)
• 1 Ch
0.01 %
5 ÷ 40k Hz
106 dBA
500
0.3 ÷ 1.2 / 1.2 ÷ 4.8 VRMS
15 k7
3
1
Output power (RMS) @ 14.4 VDC, 1% THD
Dual Power Mode - Hi-Current:
• 1 Ch @ 4 7
• 1 Ch @ 2 7
• 1 Ch @ 1 7
Dual Power Mode - A Class:
• 1 Ch @ 4 7
Amp Chain Mode (Two Linked Amplifiers)
Output power (RMS) @ 14.4 VDC, 1% THD
• 1 Ch @ 4 7
• 1 Ch @ 2 7
3000 W
4500 W
700 W x 1 Ch
75 dBA
PRE / SP-DIF (Max 192 kHz/24 bit) OPTICAL and AD Link
PRE Bypass / AD link
Removable kit (Hi-pass / Lo-pass / Band-pass 12/24 dB/oct)
32 steps 18 ÷ 7.5k Hz with 8 standard & 2 customizable modules
Master / Slave Bridge, Slave Chain
Size
B (Base) x L (Lenght) x H (Height) mm/inch
Weight kg/lb
259 x 510 x 67 / 10”1/4 x 20”1/8 x 2”11/16
10.3 / 22.71
70
Autogood products internet store http://130.com.ua
General
Special Function (Linked Amplifiers)
850 W x 1
1500 W x 1
2300 W x 1
200 W x 1
CEA Specifications
Output power @ 4 7, ≤ 1% THD+N, 14.4 V:
SN ratio (ref. 1 W output)
Inputs / Outputs / Filters
Inputs
Outputs
Filters
17
a
u
.
m
o
c
.
0
3
1
61
Autogood products internet store http://130.com.ua