Samsung DB98-29033A User manual

Wired Remote Control
MWR-WH02
Air Conditioner
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
E S F I P D G Ne Po Hu R A DB98-33323A(1)
MWR-WH02_IB_E_33323-1.indd 21
2011-01-10 오후 1:13:51
Safety Precautions
• Before using the wired remote controller, read carefully these instructions.
• After reading the instructions, keep this user's manual in a handy and safe place.
If a user is changed, you must hand over the manuals.
• Never attempt to install the air conditioning system or to move the wired remote
controller by yourself.
WARNING
D
o not attempt to install or repair this wired remote
controller by yourself.
T
his remote controller contains no user-serviceable parts.
Always consult authorized service personnel for repairs.
W
hen moving, consult authorized service personnel for
disconnection and installation of the remote controller.
E
nsure that the wall is strong enough to support the
weight of the remote controller.
M
ust install the remote controller with rated power
supply.
 In the event of a malfunction (burning smell, etc.),
immediately stop operation, turn off the electrical
breaker, and consult authorized service personnel.
CAUTION
 Do not use inflammable gases near the remote
controller.
 Do not spill water into the wired remote controller.
 Do not operate the remote controller with wet hands.
 Do not install the remote controller in a location where
it will come into contact with the combustible gases,
machine oil, sulphide gas, etc.
 Do not press buttons with a pointed thing.
 Do not pull or bend the wired remote controller cable
excessively.
 Do not use this wired remote controller for other
purpose.
 Do not spray an insecticide or other combustible things
on the wired remote controller.
 Do not clean the wired remote controller with benzene,
solvents or other chemicals.
 Do not give a shock to the wired remote controller or
disassemble it by yourself.
E-2
MWR-WH02_IB_E_33323-1.indd 2
2011-01-10 오후 1:13:27
ENGLISH
Contents
Wired remote controller .......................................................... 4
Getting Started............................................................................ 5
 Selecting the Automatic Operating Mode........................... 6
 Selecting the Cooling Mode..................................................... 7
 Selecting the Dry Mode............................................................. 8
 Selecting the Fan Mode.............................................................. 9
 Selecting the Heating Mode..................................................... 10
 Selecting the Quiet Mode.......................................................... 11
 Selecting the Sleep Mode........................................................... 12
 Adjusting the Air Swing Direction......................................... 13
 Checking the Room Temperature............................................. 14
 Locking the Wired remote controller....................................... 14
 Setting the On Timer................................................................... 15
 Setting the Off Timer.................................................................. 16
 Setting the Auto Stop Function.............................................. 17
 Setting the Temperature Limits................................................. 18
 Locking the Parts of the Wired remote controller.......... 19


E-3
MWR-WH02_IB_E_33323-1.indd 3
2011-01-10 오후 1:13:27
Wired remote controller
The wired remote controller is installed on the wall.
Operation ON/OFF button
Temperature setting
button
Temperature
display
ON/OFF time setup
ON/OFF timer/
Error Status display
Mode selection
Operation mode
display
Swing button
Room temperature
check button
Fan speed/
Air swing display
Filter Reset button
Special function
display
Fan speed setting
button
Note
DIP switch setting is recognized during the initialization. If any changes are
mode to the DIP switch setting after the initialization, you have to initialize
the system by pressing
and
or reset the power.
Press the
button after cleaning the air filter.
sign will be off.
The remote controller will display the filter sign to alert the user to clean the
filter and turn off the display when the
button are pressed.

will be displayed if you press the button of the function that the
indoor unit does not support.
If the indoor unit does not support Set temperature display,
Set temperature is not displayed on remote controller.
E-4
MWR-WH02_IB_E_33323-1.indd 4
2011-01-10 오후 1:13:28
ENGLISH
Getting Started
You have just purchased a wired remote controller and it has been installed
by your installation specialist.
Your User’s Manual contain much valuable information on using
your wired remote controller. Please take the time to read them as they will
help you take full advantage of the unit’s features.
In the manual, you will find a series of step-by-step procedures for each
function available.
The illustrations in the step-by-step procedures use 3 different symbols:
PRESS
PUSH
HOLD DOWN
E-5
MWR-WH02_IB_E_33323-1.indd 5
2011-01-10 오후 1:13:28
Selecting the Automatic Operating Mode
The room temperature and the fan speed are controlled
automatically in the auto mode.
1
Press the
(ON/OFF) button to turn on the indoor unit.
- Do not press the
(ON/OFF) button if the remote
controller is on.
Result:
2
T he air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
To select the AUTO mode, press the
displayed on the remote controller.
Result:
3
button until Auto is
 The air conditioner will operate in auto mode.
 The auto fan speed will be selected
automatically in auto mode.
You cannot control the fan speed.
To adjust the temperature, press the
buttons.
The temperature can be set between 18°C(65°F) and
30°C(86°F).
Result:
4
T he air conditioner will be turned on with the
most recently used mode.
T he temperature will be adjusted by 1°C(1°F)
when the
buttons are pressed.
To adjust the air swing direction, refer to page 13.
NoteFan speed in auto mode
When the room temperature is high, cool and strong
air will come out. After the room is cooled, mild air will
come out.
E-6
MWR-WH02_IB_E_33323-1.indd 6
2011-01-10 오후 1:13:30
ENGLISH
Selecting the Cooling Mode
Select the cooling mode to lower the room temperature.
1
Press the
(ON/OFF) button to turn on the indoor unit.
- Do not press the
(ON/OFF) button if the remote
controller is on.
Result:
2
T he air conditioner will be turned on with the
most recently used mode.
T he air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
To select the COOL mode, press the
displayed on the remote controller.
button until Cool is
Result:The air conditioner will operate in cooling mode.
3
To adjust the temperature, press the
buttons.
The temperature can be set between 18°C(65°F) and
30°C(86°F).
Result:
4
Select the fan speed by pressing the
Result:
5
T he temperature will be adjusted by 1°C(1°F)
when the
buttons are pressed.
button.
E ach time the
button is pressed, fan speed will
change in the following order:
Low
 Med
 High
 Auto
To adjust the air swing direction, refer to page 13.
NoteIf you select heating mode while the cooling mode is in
operation, cooling mode will be canceled.
E-7
MWR-WH02_IB_E_33323-1.indd 7
2011-01-10 오후 1:13:32
Selecting the Dry Mode
Select the dry mode if the room is too humid.
Using this mode will slightly lower the room temperature.
1
Press the
(ON/OFF) button to turn on the indoor unit.
- Do not press the
(ON/OFF) button if the remote
controller is on.
Result:
2
3
T he air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
To select the DRY mode, press the
displayed on the remote controller.
button until Dry is
Result:
 The air conditioner will operate in dry mode.
 The Auto fan speed will be selected
automatically in the dry mode.
You cannot control the fan speed.
To adjust the temperature, press the
buttons.
The temperature can be set between 18°C(65°F) and
30°C(86°F).
Result:
4
T he air conditioner will be turned on with the
most recently used mode.
T he temperature will be adjusted by 1°C(1°F)
when the
buttons are pressed.
To adjust the air swing direction, refer to page 13.
Note
If the indoor unit does not support Dry mode,
Dry is not displayed on remote controller.
E-8
MWR-WH02_IB_E_33323-1.indd 8
2011-01-10 오후 1:13:34
ENGLISH
Selecting the Fan Mode
Select the fan mode to circulate air without changing the
temperature.
1
Press the
(ON/OFF) button to turn on the indoor unit.
- Do not press the
(ON/OFF) button if the remote
controller is on.
Result:
2
3
T he air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
To select the FAN mode, press the
displayed on the remote controller.
button until Fan is
Result:
 The air conditioner will operate in fan mode.
 You cannot adjust the temperature in fan
mode.
Select the fan speed by pressing the
Result:
4
T he air conditioner will be turned on with the
most recently used mode.
button.
E ach time the
button is pressed, fan speed will
change in the following order:
Low
 Med
 High
To adjust the air swing direction, refer to page 13.
Note
If the indoor unit does not support Fan mode,
and you have pressed the
button, the
will be displayed.
lamp
E-9
MWR-WH02_IB_E_33323-1.indd 9
2011-01-10 오후 1:13:35
Selecting the Heating Mode
The heating mode can be selected only on the heat pump models.
Select the heat mode to raise the room temperature.
1
Press the
(ON/OFF) button to turn on the indoor unit.
- Do not press the
(ON/OFF) button if the remote
controller is on.
Result:
The air conditioner will be turned on with the
most recently used mode.
The air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
2
To select the HEAT mode, press the
button until Heat is
displayed on the remote controller.
Result:The air conditioner will operate in heating mode.
3
To adjust the temperature, press the
buttons.
The temperature can be set between 16°C(61°F) and
30°C(86°F).
Result:
The temperature will be adjusted by 1°C(1°F)
when the
buttons are pressed.
4
Select the fan speed by pressing the
Result:
5
The air conditioner will start heating if the
set temperature is higher than the room
temperature.
The fan will operate even if the set
temperature is lower than the room
temperature.
button.
E ach time the
button is pressed, fan speed
will change in the following order:
Low
 Med
 High
 Auto
To adjust the air swing direction, refer to page 13.
Note
E-10
MWR-WH02_IB_E_33323-1.indd 10
 After starting heating operation, the air may not come out
immediately to prevent the cold air from coming out.
 (Defrost indicator)
- Defrost indicator will be on while your outdoor unit
defrosts the frost formed during heating operation.
After defrosting is completed, the indicator will be off.
(Air will not come out of the indoor unit while defrosting.)
 If you stop running the air conditioner after heating
operation, the air will come out for a while to radiate heat.
 If you select cooling mode while the heating mode is in
operation, heating mode will be canceled.
2011-01-10 오후 1:13:38
ENGLISH
Selecting the Quiet Mode
Select the quiet mode to run the indoor unit as quietly as
possible.
1
Press the
(ON/OFF) button to turn on the indoor unit.
- Do not press the
(ON/OFF) button if the remote
controller is on.
Result:
T he air conditioner will be turned on with the
most recently used mode.
2
Select the desired operation mode by pressing the
button.
3
Press the
The air conditioner will operate in quiet mode.
Operating noise will be reduced.
Note
ress the
P
mode.
Note
button to select the Quiet mode.
Result:
button again to exit the quiet
 If the indoor unit does not support Quiet mode,
will be displayed when you press the
button.
 If you press the
button in fan mode,
will be displayed.
E-11
MWR-WH02_IB_E_33323-1.indd 11
2011-01-10 오후 1:13:39
Selecting the Sleep Mode
Select the sleep mode to sleep in comfort without worrying to
turn off the air conditioner in the middle of the night.
The air conditioner will turn off automatically after 6 hours.
1
Press the
(ON/OFF) button to turn on the indoor unit.
- Do not press the
(ON/OFF) button if the remote
controller is on.
Result:
2
T he air conditioner will be turned on with the
most recently used mode.
Select the desired operation mode by pressing the
button.
NoteOnly cooling and heating mode support the sleep
mode.
3
Press the
The air conditioner will operate in sleep mode.
The air conditioner will gradually raise or
lower the set temperature internally and
eventually turn off automatically after 6 hours.
Note
Press the
Note
button to select the Sleep mode.
Result:
button again to exit the sleep mode.
 If the indoor unit does not support Sleep mode,
will be displayed when you press the
button.
 If the indoor unit is not in Cool/Heat mode,
will be displayed when you press the
button.
E-12
MWR-WH02_IB_E_33323-1.indd 12
2011-01-10 오후 1:13:40
ENGLISH
Adjusting the Air Swing Direction
Adjust the air swing direction to circulate the air according
to various needs. By adjusting the air swing direction, the
efficiency of the air conditioner can be increased.
1
Press the
button.
Result:
The blade will start swinging up and down.
Press the
button again to stop the
blade from swinging and set the blade to the
desired position.
NoteThe air swing direction cannot be set on duct type
indoor units.
will be displayed when the
button is
pressed.
E-13
MWR-WH02_IB_E_33323-1.indd 13
2011-01-10 오후 1:13:41
Checking the Room Temperature
You can check the current room temperature.
1
Press the
Result:
button to check the room temperature.
T he room temperature will be displayed for
3 seconds and return to set temperature display.
NoteThe room temperature may be slightly different
depending on the installation location of the
remote controller.
Locking the Wired remote controller
Lock the wired remote controller to prevent it from children and
changing the settings unwillingly.
1
Press the
Result:
button for 3 seconds.
 will be displayed and the wired remote
controller is locked.
When the wired remote controller is locked,
you cannot control the air conditioner by the
wired remote controller.
NotePress the
the lock.
button for 3 seconds again to cancel
E-14
MWR-WH02_IB_E_33323-1.indd 14
2011-01-10 오후 1:13:42
ENGLISH
Setting the On Timer
You can set the indoor unit, which is connected to the wired
remote controller, to turn on at the pre-set time.
1
Press the
Result:
2
3
Press the
button to set the On Timer.
Default time (0.5 hour) will be displayed
and the ‘On’ indicator will blink.
If the On Timer is already set, current time will
be displayed and ‘On’ indicator will blink.
button until you set your desired time.
Result:
You can set the time between 0.5~24 hours.
Note
0.5~3 hours : Time will be changed in 0.5 hour
unit each time you press the
button.
3~24 hours : Time will be changed in 1 hour
unit each time you press the
button.
Press
button to set the time.
Result:
‘On’ indicator will stop blink.
When the pre-set time passes, indoor unit will
turn on automatically.
Operation mode, temperature, fan speed, air
flow direction will be same as the most recent
operation settings.
Note
 When the On Timer is set, you can cancel it by
pressing the
button.
 When the centralized control is set, Timer will not be
effective.
 Timer will be canceled if you press either
or
button while the Timer is already set.
 Timer will be canceled if you reset the wired remote
controller.
 You can set one On Timer and Off Timer each.
 Timer will be canceled if you turn on the wired remote
controller with
button while the Timer is set.
E-15
MWR-WH02_IB_E_33323-1.indd 15
2011-01-10 오후 1:13:43
Setting the Off Timer
You can set the indoor unit, which is connected to the wired
remote controller, to turn off at the pre-set time.
1
Press the
Result:
2
3
Press the
button to set the Off Timer.
D
efault time (0.5 hour) will be displayed and
the ‘Off’ indicator will blink.
If the Off Timer is already set, current time will
be displayed and the ‘Off’ indicator will blink.
button until you set your desired time.
Result:
You can set the time between 0.5~24 hours.
Note
0.5~3 hours : Time will be changed in 0.5 hour
unit each time you press the
button.
3~24 hours : Time will be changed in 1 hour
unit each time you press the
button.
Press
button to set the time.
Result:
‘Off’ indicator will stop blink.
When the pre-set time passes, indoor unit will
turn off automatically.
Note
 When the Off Timer is set, you can cancel it by
pressing the
button.
 When the centralized control is set, Timer will not be
effective.
 Timer will be canceled if you press either
or
button while the Timer is already set.
 Timer will be canceled if you reset the wired remote
controller.
 You can set one On Timer and Off Timer each.
 Timer will be canceled if you turn off the wired remote
controller with
button while the Timer is set.
E-16
MWR-WH02_IB_E_33323-1.indd 16
2011-01-10 오후 1:13:44
ENGLISH
Setting the Auto Stop Function
The wired remote controller can be set to turn off the indoor
unit(s) after a set period of time has passed since any button on
the remote controller was last pressed. This function is used to
turn off the indoor unit in case the user forgets to turn off the
indoor unit.
1
Press the
mode.
Result:
2
 T he wired remote controller will enter the
setup mode and the menu will display .
Press the
button to enter the Auto Stop
setup mode.
Press the
Result:
3
button for 3 seconds to enter the setup
Press the
Result:
buttons to set the auto stop time.
Time is adjusted by 1 hour when the
buttons are pressed.
The default time setting is 0. The auto stop
time can be set between 0 and 12 hours.
If you select 0, auto stop function will be
canceled.
button to complete the auto stop function.
Auto stop function is set.
Note To cancel the auto stop function, press the
button.
4
Press the
Result:
button.
Menu selection display will end.

will be displayed.
Note
 The time-counting of Auto Stop function is clear
after pressing the
,
,
,
,
,
buttons.
 Auto Stop function doesn’t work under the
centralized control.
,
E-17
MWR-WH02_IB_E_33323-1.indd 17
2011-01-10 오후 1:13:46
Setting the Temperature Limits
You can set upper limit/lower limit temperature so that the
desired temperature is not set too high or low.
1
Press the
mode.
Result:
2
Press the
Result:
3
Press the
settings.
Each time the
buttons are pressed,
menu number increases by 1.
Press the
button to enter the
temperature limit setup mode.
button to complete the temperature limit
Result:
T he temperature setting will be restricted
by the set lower/upper temperature limit.
Note Press the
Press the
Result:
Note
buttons and select menu .
Set the lower limit first by pressing the
buttons followed by the
button and set the upper limit.
Each time the
buttons are pressed,
the temperature is increased/decreased
by 1°C(1°F) .
Press the
button after setting.
Press the
button to cancel the
temperature limits setup.
5
T he wired remote controller will enter the setup
mode and the menu will
display .
Set the lower and upper temperature limit by pressing the
buttons.
Note 4
button for 3 seconds to enter the setup
button to cancel the setting.
button.
Menu selection display will end.
 The lower limit can not be same or higher than upper
limit.
 Even though you set the lower temperature limit to
16°C(61°F), lower temperature will be set to 18°C(65°F) in
all the modes except in heating mode. When you set the
lower temperature limit to 18°C(65°F), it will be applied
under all the operation modes.
E-18
MWR-WH02_IB_E_33323-1.indd 18
2011-01-10 오후 1:13:48
ENGLISH
Locking the Part of the Wired remote controller
To prevent the wired remote controller from children and
changing settings unwillingly, you can lock some functions of
wired remote controller.
1
Press the
mode.
Result:
2
3
4
5
buttons and select menu .
Result:
Each time the
buttons are pressed,
menu number increases by 1.
Press the
mode.
Note Press the
Using the
value of the
,
button to enter the lock setup
button to cancel the setting.
buttons, you can set the lock setting
,
,
buttons.
Result:
Lock setting value
- 0: Cancel lock
- 1: Set lock
Press the
button after setting.
On/off
button
Press the
button to complete the part lock settings.
Result:
Changed settings will be applied.
 will be displayed when the lock function is
set.
Note Press the
Press the
Note
T he wired remote controller will enter the setup
mode and the menu will
display .
Press the
Result:
button for 3 seconds to enter the setup
Temperature
setting button
Fan speed button
Mode button
button to cancel the setting.
button.
Menu selection display will end.
 If the centralized control is set, you cannot use the
part lock function.
 You cannot use the part lock function when Lock all
is set.
 Part Lock function can be applied to
, and
buttons only.
,
,
E-19
MWR-WH02_IB_E_33323-1.indd 19
2011-01-10 오후 1:13:50
MWR-WH02_IB_E_33323-1.indd 20
2011-01-10 오후 1:13:51