PHONES
(044) 360-7-130
(050) 336-0-130
(063) 788-0-130
(067) 233-0-130
(068) 282-0-130
Internet store of
autogoods
ICQ
294-0-130
597-0-130
SKYPE
km-130
CAR RECEIVERS — Receivers • Media receivers and stations • Native receivers • CD/DVD changers • FM-modulators/USB adapters • Flash memory • Facia plates and adapters • Antennas • Accessories |
CAR AUDIO — Car audio speakers • Amplifiers • Subwoofers • Processors • Crossovers • Headphones • Accessories | TRIP COMPUTERS — Universal computers • Model computers • Accessories |
GPS NAVIGATORS — Portable GPS • Built-in GPS • GPS modules • GPS trackers • Antennas for GPS navigators • Accessories | VIDEO — DVR • TV sets and monitors • Car TV tuners • Cameras • Videomodules
• Transcoders • Car TV antennas • Accessories | SECURITY SYSTEMS — Car alarms • Bike alarms • Mechanical blockers • Immobilizers • Sensors • Accessories | OPTIC AND LIGHT — Xenon • Bixenon • Lamps
• LED • Stroboscopes • Optic and Headlights • Washers • Light, rain sensors • Accessories | PARKTRONICS AND MIRRORS — Rear parktronics • Front parktronics • Combined parktronics • Rear-view mirrors
• Accessories | HEATING AND COOLING — Seat heaters • Mirrors heaters • Screen-wipers heaters • Engine heaters • Auto-refrigerators • Air conditioning units • Accessories | TUNING — Vibro-isolation
• Noise-isolation • Tint films • Accessories | ACCESSORIES — Radar-detectors • Handsfree, Bluetooth • Windowlifters • Compressors • Beeps, loudspeakers • Measuring instruments • Cleaners • Carsits
• Miscellaneous | MOUNTING — Installation kits • Upholstery • Grilles • Tubes • Cable and wire • Tools • Miscellaneous | POWER — Batteries • Converters • Start-charging equipment • Capacitors
• Accessories | MARINE AUDIO AND ELECTRONICS — Marine receivers • Marine audio speakers • Marine subwoofers • Marine amplifiers • Accessories | CAR CARE PRODUCTS — Additives • Washer fluid •
Care accessories • Car polish • Flavors • Adhesives and sealants | LIQUID AND OIL — Motor oil • Transmission oil • Brake fluid • Antifreeze • Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in
Kyiv and other cities, delivery by ground and postal services. Our experienced
consultants will provide you with exhaustive information and help you to chose
the very particular thing. We are waiting for you at the address
http://130.com.ua
a
u
.
m
o
.c
0
3
1
Power Amplifier
Instruction Manual
To ensure maximum performance and safety,
please follow this manual. Please retain the
manual for future reference after installation
STEREO 2
STEREO 4
BASS 1
Autogood products Internet store “130”
OWNERS MANUAL
Model: BLACKBOX STEREO 2 / STEREO 4 / BASS 1
Congratulations on purchasing your VIBE BlackBox
amplifier Please read this manual in order to fully
understand how to get the best results from your
amplifier.
Please ensure that all advice on how to look after your
amplifier is followed.
Thank you for buying VIBE, we hope you enjoy listening to
your product as much as we enjoyed creating it.
VIBE R&D Division
a
u
.
m
o
.c
0
3
1
Mounting Guidelines
Your VIBE amplifier is designed with a swift installation routine in mind. Please mount the amplifier in a dry location on a solid
surface. NEVER mount the amplifier upside down, this will cause the amplifier to over heat and will eventually damage the
amplifier. Before fixing the amplifier in place please ensure that there is sufficient air flow around the exterior of the casing,
at least two inches is sufficient.
FUSE
close to battery
Autogood products Internet store “130”
Connections
Ground Cable
●
●
●
●
The ground cable needs to carry the same current as the power cable. At least an 8 gauge cable should be used.
The amplifier ground should be connected directly to the chassis of the vehicle, to bare metal.
The cable length should be kept to an absolute minimum.
It is not recommended that you connect the ground cable to the vehicles seatbelts anchor point.
Remote Turn On
A minimum of 18 gauge cable should be used for this connection.
The cable should be run with exactly the same care and attention as the power cable and taken back to the source
(headunit) and joined to the remote cable provided.
● If the source (headunit) does not have a remote turn on cable then a 12v supply should be used. This will require a
switch to be fitted inline to enable the amplifier to be turned on and off. Remember that if this switch is left on you will
flatten the car battery.
●
●
●
●
●
RCA Cables
Depending on the model number of your amplifier and the number of speakers you wish to power you will have to run
either one or two RCA cables from the source to the amplifier.
Please take extra care when running these cables from the source to the amplifier. Ensure that they are placed away
from all items that can generate any interference, wiring harnesses etc.
It is recommended that the RCA cables should be run on opposite sides of the car to the previously installed power
cables if possible, to avoid the cable picking up interferance.
a
u
.
Power Cable
●
●
●
●
●
At least an 8 gauge cable should be used for both the power and the ground connections to the amplifier.
The power cable should be taken directly from the battery. Rubber grommets should be used when passing through
any bulkheads to prevent the cable from becoming chaffed or cut.
It is vital that a fuse / circuit breaker (of at least equal value to the one fitted on the amplifier) is placed inline with the
power cable and is no further than eighteen inches away from the battery.
Please ensure that the fuse is not fitted until the entire installation procedure is complete.
The two tables below are to help you decide on what cable is correct for you. The first enables you to select the size of
cable depending on the length required. The second will help you convert the cable size from American Wire Gauge to
Metric if you need to.
m
o
.c
Current demand
0–20 amps
20–35 amps
35–50 amps
50–65 amps
65–85 amps
85–105 amps
105–125 amps
125–150 amps
0 – 4 Ft
14
12
10
8
6
6
4
2
0
3
1
AWG Number
0
1
2
3
4
5
6
7
8
9
10
4 – 7 Ft
12
10
8
8
6
6
4
2
7 – 10 Ft
12
8
8
6
4
4
4
2
Length of Run
10 – 13 Ft
10
8
6
4
4
2
2
0
13 – 16 Ft
10
6
4
4
2
2
0
0
AWG to Metric Conversion Chart
cross sectional area
Inch
mm
0.325
0.289
0.258
0.229
0.204
0.182
0.162
0.144
0.128
0.114
0.102
8.25
7.35
6.54
5.83
5.19
4.62
4.11
3.66
3.26
2.91
2.59
Autogood products Internet store “130”
16 – 19 Ft
8
6
4
4
2
2
0
0
19 – 22 Ft
8
6
4
4
2
2
0
0
mm2
53.5
42.4
33.6
26.7
21.1
16.8
13.3
10.5
8.36
6.63
5.2
22 – 28 Ft
8
4
4
2
0
0
0
0
Connections and Controls - BlackBox Stereo 2
2
1
3
4
10
5
6
7
8
9
12
11
a
u
.
m
o
.c
1. High Level Input
To be used when no RCA's are available. Use the provided loom to connect to closest speakers. The loom connector will only
fit one way around. Once plugged in you should connect the wires as below:
0
3
1
2. Low Level Input / Output
Low level input connection to any source (head unit) with a low level output. This is your RCA output from the source
(headunit)
Low level output is a daisy chain RCA connection to allow easy addition of another amplifier.
3.
Gain Control
Used to match the input signal of the source to the amplifier. See the setup section for more details.
4. Bass Boost Switch
To provide up to an extra +24 dB of bass boost at 45 Hz. Use this boost to Increase bass output from the amplifier.
5. Low Pass Crossover Control
The control is used to select the low pass filter frequency. The frequency ranges are from 30 Hz to 300 Hz.
6. Crossover Control Switch
This switch is used to select high pass, low pass or full (no crossover) operation for the amplifier speaker outputs.
7. High Pass Crossover Control
The control is used to select the high pass filter frequency. The frequency ranges are from 50 Hz to 1KHz.
Autogood products Internet store “130”
8. Gain Remote Input Jack
Use to plug in the remote bass controller. (BBR09 optional ) see website for details www.vibeaudio.co.uk
9. Indicator LEDs
When the amplifier is operating correctly the green LED will illuminate. When the amplifier is in protection mode the red LED
will illuminate
10. Power Connections
Power connections. See Connections section for details on correct connections.
11. Fuses
Please ensure the following fuse rating is used when replacing fuses: 15 amp x 2
12. Speaker Terminal Output
For connection to the speakers. See Application section for wiring examples.
Applications - BlackBox Stereo 2
a
u
.
m
o
.c
0
3
1
Autogood products Internet store “130”
Connections and Controls
2
- BlackBox Stereo 4
6
3
13
7
1
13
4
5
12
8
9
10
11
a
u
.
m
o
.c
1. Low Level Input
For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit). In order
to obtain a four channel output from a two channel input please set the switch to 4 channel and plug the RCA's into channel
3 and channel 4.
2. High Level Input
0
3
1
To be used when no RCA's are available. Use the provided loom to connect to closest speakers. The loom connector will only
fit one way around. Once plugged in you should connect the wires as below:
Front Speakers
Left Positive - Brown
Left Negative - Blue
Right Positive - Black
Right Negative - Green
Rear Speakers
Left Positive - Orange
Left Negative - Grey
Right Positive - Yellow
Left Negative - White
3. Front Gain Control
Used to match the input signal of the source to the amplifier. See the setup section for more details.
4. Front Crossover Control
The switch is used to select between low pass / high pass filter or no filter at all on the front channels. The frequency ranges
on the low pass filter are from 30 Hz to 300 Hz. The frequency ranges on the high pass filter are from 50 Hz to 1KHz.
5. Front Bass Boost Switch
To provide up to an extra +24 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
6. Rear Gain Control
Used to match the input signal of the source to the amplifier. See the setup section for more details.
Autogood products Internet store “130”
7. Rear Bass Boost Switch
To provide up to an extra +24 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
8. Rear Crossover Control
The switch is used to select between low pass / high pass filter or no filter at all on the rear channels. The frequency
ranges on the low pass filter are from 30 Hz to 300 Hz. The frequency ranges on the high pass filter are from 50 Hz to
1KHz.
9. Rear Gain Remote Input Jack
Use to plug in the remote bass controller. (BBR09 optional ) see website for details www.vibeaudio.co.uk
10. Indicator LEDs
When the amplifier is operating correctly the green LED will illuminate. When the amplifier is in protection mode the red
LED will illuminate
11. Power Connections
Power connections. See Connections section for details on correct connections.
12. Fuses
Please ensure the following fuse rating is used when replacing fuses: 30 amp x 2
13. Speaker Terminal Output
For connection to the speakers. See Application section for wiring examples.
a
u
.
Applications - BlackBox Stereo 4
m
o
.c
0
3
1
Autogood products Internet store “130”
Connections and Controls
9
- BlackBox BASS 1
4
7
3
5
6
1
2
10
12
8
11
a
u
.
m
o
.c
1. Low Level Input / Output
Low level input connection to any source (head unit) with a low level output. This is your RCA output from the source
(headunit)
Low level output is a daisy chain RCA connection to allow easy addition of another amplifier.
2. Gain Control
0
3
1
Used to match the input signal of the source to the amplifier. See the setup section for more details.
3. Low Pass Filter Control
Low pass frequency control. The frequency ranges from 40 Hz to 250 Hz.
4. Phase Control
Can be used to alter the phase of the subwoofer from 0 - 180 degrees.
IE: The speaker output can be In phase or out of phase with the other speakers in the vehicle. For best results flick between
the two settings to determine the best results.
5. Subsonic Filter Control
This is used to filter out unwanted amplifier output to the subwoofer. Effectively this will filter out all the frequencies up to the
crossover point set with the control. The range is from 15 Hz to 50 Hz. Frequencies of 80 Hz and below cause the subwoofer
to work hard, some subwoofers can easily be damaged when playing very low frequencies. Using the subsonic filter allows
less distortion, delivers frequencies better suited to the subwoofer prolonging its life.
6. Subsonic Filter Switch
Used to turn the filter on or off.
7. Bass Boost Switch
To provide up to an extra +18 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
Autogood products Internet store “130”
8. Bass Remote Input Jack
Use to plug in the remote bass controller.
9. Indicator LEDs
When the amplifier is operating correctly the LED will show as blue. When the amplifier is in protection mode the LED will
show as red.
10.Fuses
Please ensure the following fuse rating is used when replacing fuses:
35 amp x 4
11. Speaker Terminal Output
For connection to the speakers. See Application section for wiring examples.
12. Power Connections
Power connections. See Connections section for details on correct connections.
Applications - BlackBox Stereo 4
a
u
.
m
o
.c
0
3
1
Autogood products Internet store “130”
Set Up Section
To correctly set the gain control of the amplifier to match that of the source (headunit) use the following setup routine:
Turn the gain control to minimum on the amplifier.
Ensure the bass boost is set to 0 dB.
On the headunit set all crossovers ( if applicable) to flat and both bass and treble to zero.
Turn up the source (headunit) to approx 3/4 volume.
Very slowly turn up the gain on the amplifier until distortion can be heard in any of the speakers or until the volume reaches
an uncomfortable listening level when this is reached turn down the gain control slightly.
The gain control is now set.
The setting of the crossover will depend on what kind of speaker you are installing.
For a subwoofer it is recommended that the crossover is set to Low Pass and the frequency is set to match that of the
speakers specifications, or your preferred frequency - this is usally about 60 - 120
For a pair of full range speakers it is recommended that the crossover is set to Flat. The two frequency controls will then
have no effect on the amplifiers output and the speaker will receive a full range signal. However, using the high pass
crossovers will allow more control of your speakers. By removing the bass (low frequencies) the speakers can perform at
higher volumes with less distortion.
Note: The smaller the speaker, the less bass it can handle. Adjust the crossover to get the most and best sound from your
speakers. The easiest was to do this is by limiting the amount of bass you feed them.
a
u
.
For a pair of speakers with a passive crossover it is recommended that the crossover is set to High Pass and the frequency
is set to match that of the speakers specifications. - This is usually about 40 - 120Hz
Note:
m
o
.c
By using the crossovers correctly you will not only lengthen the life of your speakers but you will also get better performance
from them. To optimise your setup seek the advise of a professional installation engineer or visit your local VIBE audio dealer.
0
3
1
Autogood products Internet store “130”
Troubleshooting
●
●
●
Before removing the amplifier, refer to the list below and follow the suggested procedures.
Always test the speakers and confirm that they are wired correctly first.
If in any doubt get help from a qualified auto electrician.
Amplifier Will Not Power Up
✓
✓
✓
✓
✓
Check for good ground connections. Ensure Ground cable is connected directly to bare metal and not a painted
surface.
Using a multimeter check that remote terminal has at least 7V DC.
Using a multimeter check that there is battery voltage of at least 10.5v DC on the positive terminal.
Check all fuses.
Check that the protection light is not illuminated. If it is lit, shut off the amplifier by disconnecting for thirty seconds and
then turning it back on.
Protection LED Illuminates When Amplifier Is Powered Up
✓
●
●
Check for shorts on all speakers wires. (IE no speaker wires should be joined together and no speaker wires should be
touching the cars chassis)
The amplifier is designed to shut down automatically when the units temperature goes above 80 degrees. If the
amplifier feels very hot then this may be the reason for the amplifier not starting.
Remove the speaker wires and reset the amplifier. If the Protection LED still comes on then the amplifier is faulty. This
damage may have been caused by either failure to follow these setup guidelines or abuse.
Amplifier Gets Very Hot
✓
✓
✓
m
o
.c
Blown Fuse(s)
✓
✓
✓
✓
a
u
.
Check the minimum speaker impedance for the amplifier is correct.
Check for shorts on all speakers wires. (ie no speaker wires should be joined together and no speaker wires should be
touching the cars chassis)
Check that there is good airflow around the amplifier. In some applications an external fan may be required.
Check both positive supply and ground for shorts.
Check that the positive wire is connected to the positive terminal on the amplifier.
Check that the negative wire is connected to the ground terminal on the amplifier.
Ensure that the correct rated fuse is fitted:
0
3
1
VIBE BlackBox Stereo 2 –15 amp x 2,
VIBE BlackBox Stereo 4 –30 amp x 2,
VIBE BlackBox Bass 1 –35 amp x 4,
Distorted Sound
✓
✓
✓
✓
Check the gain control is not set at too high If the speakers sound distorted turn down the gain until the
sound is clear.
Check that all crossover frequencies are correct. See Setup section for more details.
Check for shorts on all speaker wires.
Check all speakers are wired correctly. With the correct polarity being observed on each connection.
Autogood products Internet store “130”
BlackBox stereo amplifiers
BlackBox stereo 4
Specification
BlackBox stereo 2
RMS Power @ 13.8v DC
Power @ 4 Ohms stereo
Power @ 2 Ohms stereo
Power @ 4 Ohms bridged
2 x 100 WRMS
2 x 125 WRMS
1 x 250 WRMS
4 x 100 WRMS
4 x 125 WRMS
2 x 250 WRMS
Minimum speaker impendence
THD Distortion
IMD Distortion
Frequency Response
Input Sensitivity
Input Impendence
Signal to Noise Ratio
Channel Separation
2 Ohm stereo / 4 Ohm bridged
0.1%
0.1%
7Hz - 38 KHz
250 mV - 5V
15K
96 dB
-61 dB
2 Ohm stereo / 4 Ohm bridged
0.1%
0.1%
5Hz - 43 KHz
250 mV - 5V
15K
88 dB
-57 dB
Crossover Network
Low pass filter
Bass Boost
High pass filter
Fuse rating
Size length x width x height
30 Hz – 300 Hz
0 dB - +24 Db
50 Hz – 1KHz
15A x 2
348mm x 224mm x 57 mm
30 Hz – 300 Hz
0 dB - +24 Db
50 Hz – 1KHz
30A x 2
448mm x 224mm x 57 mm
m
o
.c
BlackBox bass amplifier
Specification
30
RMS power @ 13.8 vDC
1
Power @ 4 ohms
Power @ 2 Ohms
Power @ 1 Ohm
a
u
.
BlackBox bass 1
1 x 650 WRMS
1 x 1000 WRMS
1 x 1250 WRMS
Minimum speaker impedance
THD Distortion
IMD Distortion
Input Sensitivity
Input Impedance
Signal to Noise Ratio
1 ohm
0.8 %
0.8 %
250 mv - 5V
15 K
95 dB
Crossover Network
Low Pass Filter
Bass Boost
Subsonic Filter
Fuse Rating
Size length x width x height
40 Hz - 250 Hz
0 dB -+18 dB
15 Hz - 50 Hz
35 amp x 4
478 mm x 224mm x 57mm
Autogood products Internet store “130”
a
u
.
m
o
.c
0
3
1
Autogood products Internet store “130”
In order to protect your purchase and aid your
warrantee please fill in the following form and
keep it safe for your future reference:
Model Number:
Serial Number:
Purchased From:
KEEP IT SAFE
Staple your receipt here:
Date of Purchase:
a
u
.
m
o
.c
Limited Warranty
All VIBE products carry a full twelve months warranty, valid from the date of the original receipt / proof of purchase. In
order to validate this warranty, the warranty card should be returned to VIBE within seven days of the original purchase
date. The original receipt and packaging should also be retained for this twelve month period.
If at any stage during the warranty period you have a problem with the product then it should be returned to the point of
purchase, with proof of purchase in its original packaging, complete with no items missing.
If the store is unable to fix the product it may have to be returned to VIBE this process takes around 7 working days.
A full description of VIBE's warranty information can be found on our website:
0
3
1
www.vibeaudio.co.uk/warranty
A written version can also be obtained from
VIBE warranty Dept, PO BOX 11000, B75 7WG
Technical enquires
call 09067031420
call cost 50p per minute Call costs correct at date of publication (02/02/08) Hours of business 9.00am - 5.30pm all calls are recorded for training
purposes MIDBASS Distribution PO Box 11000,B75 7WG
Copyright
All content included in this manual such as text, graphics, logos, icons, images and data, are the property of VIBE Technologies Limited (herein referred to as "VIBE", "us" or "we") and its affiliate or
their content and technology providers, and are protected by United Kingdom and International copyright laws. All rights reserved.2008
All stylised representations of product names, or the abbreviations of product names, as logos are all trademarks of VIBE. Graphics and logos are trademarks or trade dress of VIBE Technologies
Ltd or its subsidiaries.
VIBE's trademarks and trade dress may not be used in connection with any product or service that is not VIBE's, in any manner that is likely to cause confusion among customers or in any manner
that disparages or discredits VIBE. All other trademarks not owned by VIBE or its subsidiaries that appear in this manual are the property of their respective owners, who may or may not be affiliated
with, connected to, or sponsored by VIBE or its subsidiaries.
TO THE FULLEST EXTENT PERMITTED AT LAW, VIBE IS PROVIDING THIS MANUAL AND ITS CONTENT ON AN "AS IS" BASIS AND MAKES NO (AND EXPRESSLY DISCLAIMS ALL)
REPRESENTATIONS OR WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WITH RESPECT TO THIS MANUAL OR THE INFORMATION, CONTENT, MATERIALS OR PRODUCTS
INCLUDED IN THIS MANUAL INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IN ADDITION, VIBE DOES NOT REPRESENT OR WARRANT THAT THE INFORMATION CONTAINED IN THIS MANUAL IS COMPLETE OR CURRENT, AND THAT ALL SPECIFICATIONS AND
INFORMATION CONTAINED WITHIN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE.
VIBE RECOMMEND CAUTION WHEN LISTENING TO MUSIC REPRODUCED THROUGH VIBE EQUIPMENT. VIBE EQUIPMENT IS CAPABLE OF PRODUCING SOUND AND SOUND
PRESSURE LEVELS THAT CAN PERMANENTLY DAMAGE HEARING OF YOU AND THAT OF OTHERS. FOR SAFE AND ENJOYABLE LISTENING, THE SOUND SHOULD BE CLEAR
WITHOUT DISTORTION AT A COMFORTABLE VOLUME.
BY USING ANY VIBE EQUIPMENT, YOU AGREE TO TAKE FULL RESPONSIBILITY FOR YOUR OWN SAFETY AND THE SAFETY OF OTHERS WHEN LISTENING TO MUSIC AT HIGH
VOLUMES THROUGH EQUIPMENT YOU HAVE PURCHASED. USE OF ANY VIBE EQUIPMENT CONSTITUTES AGREEMENT TO THIS DISCLAIMER.
Except as specifically stated in this manual, to the fullest extent permitted at law, neither VIBE nor any of its affiliates, directors, employees or other representatives will be liable for damages arising
out of or in connection with the use of this manual or the information, content, materials or products included.
This is a comprehensive limitation of liability that applies to all damages of any kind, including (without limitation) compensatory, direct, indirect or consequential damages, loss of data, income or
profit, loss of or damage to property and claims of third parties. For the avoidance of doubt, VIBE does not limit its liability for death or personal injury to the extent only that it arises as a result of
negligence of VIBE, its affiliates, directors, employees or other representatives.
Autogood products Internet store “130”
FLATBASS™ 13 SPK Bass speaker cable
There are many powerful bass amplifiers on today’s market – the ever increasing power is putting huge strains on speaker wire
– VIBE present a new breed of speaker cable specially developed for BASS applications – the VIBE FLATBASS speaker cable
offers SolidCores™ that can handle and sustain considerably more power than conventional speaker cable.
Model: FlatBass 13 SPK – 13 gauge SolidCore™ flat BASS speaker cable
VIBE 140 amp circuit breaker
Big systems require big protection – The VIBE circuit breaker is rated at a massive 140 amps and offers critical protection to
your system – if the system over powers or short circuits the breaker will cut in and save your equipment. No need to replace
expensive fuses, system is reset via a simple switch – also offers safe and instant system shutdown.
Model: CB140 – 140 amp circuit breaker
FLAT Y 2M / FLAT Y 2F RCA Y leads
Our professional quality full range OFC Y-interconnect guarantees a pure and strong signal. With a flat
design and ferrite loaded gold plated plugs interference is greatly reduced. The FLAT-Y Interconnect is
available in 1 male – 2 female FLAT Y 2F and 2 male – 1 female FLAT Y 2M configurations.
Model: FLAT Y 2f – 1 pair RCA Y lead 1male to 2 female
Model: FLAT Y 2m – 1 pair RCA Y lead 2male to 1female
VIBE BC10 level controller
The VIBE BC10 gain level controller is a perfect addition to any subwoofer system, the BC10 allows the level of the amplifier to be
controlled from the driver’s seat giving the user easy adjustment of gain level. Particularly useful for adjusting the gain level for
amplifiers controlling subwoofers. The BC10 controller is RCA input and output making it compatible with any system allowing gain
level adjustment of any amplifier it is connected to. It can also be used with full range amplifiers.
Model: BC10 – RCA Gain level control
Slick level remote
A new addition to the Slick range of amplifiers is the Slick level control which allows level adjustment of the amplifier from the front of
the car - Simply plug the supplied cable into the Slick remote level port on the end panel of the amplifier and remote gain control is
yours, it is that easy.
Model: SLR1 – optional remote for use with all Slick amplifiers
VIBE PortPlug™
The VIBE PortPlug allows easy tuning of the VIBE CBR bass enclosures. The PortPlug™ is used to tightly
seal the VIBE TurboPort™ in the enclosure to either create a sealed enclosure for better transient
response or in the case of a multi ported enclosure re-tune the enclosure using only 1 PortPlug™
Model: PP25 – PortPlug™ for 2.5” TurboPort™
Model: PP30 - PortPlug™ for 3” TurboPort™
a
u
.
VIBE official Merchandise
MPS – VIBE polo shirt with embroidered VIBE logo on front and rear
MTS – VIBE T-shirt with small VIBE printed logo on front.
MCD – VIBE CD, containing exclusive VIBE bass tracks as featured on the Bass Tunnel and VIBE Dredd.
MCC – VIBE CD case, metallic silver CD case with VIBE logo.
VFL – VIBE fleece with embroidered logo on the front and large on back.
VTD – VIBE tax disc holder, stylish silver tax disc holder featuring VIBE logo.
m
o
.c
VIBE SD4/5 subwoofer defender grill
The new VIBE subwoofer defender not only provides protection for your sub but also adds style with its metallic
badge and black rubberised steel construction allow it to integrate perfectly with the VIBE EVO enclosures
Model: SD4 – sub grill fits both 10” and 12” subwoofers
Model: SD5 – sub grill fits 15” subwoofers
0
3
1
VIBE GB41 banana plug
The VIBE GB41 banana plugs are the easy and convenient way to quickly remove your bass enclosure without
having to constantly re-thread your speaker cable into the box terminal, simply attach the speaker cable to the
VIBE GB41 banana plug and you have a reliable quick release solution. Designed for optimum use with the TP-2
and QP-4 terminal, our professional gold plated 4mm banana plugs are polarity marked and feature rubber
shrouds.
Model: GB41 – Gold Banana plug
VIBE DB6 non fused distribution block
The VIBE DB6 non fused distribution block is a professional non fused distribution block which gives easy
connection for up to 5 amplifiers. The VIBE DB6 has 2 x 4AWG input and 4 x 8AWG outputs which can be
used for power distribution or ground distribution giving a common grounding point for all system
components eliminating the risk of ground loop interference.
Model: DB6 non fused distribution block
VIBE FD4 fused distribution block
The VIBE FD4 fused distribution block is a professional AGU fused distribution block which gives easy
connection for up to 4 amplifiers. The VIBE FD4 has 1 x 4AWG input and 4 x 8AWG outputs each
individually fused up to a maximum of 80 amps (AGU fuses available separately)
Model: FD4 – 4 way AGU fused distribution block, 1 x 4 gauge input 4 x 8 gauge outputs
VIBE CT0 / CT4 compression fit ring terminal
The VIBE CT range of gold plated ring terminals are professional compression fit designed for maximum
conductivity when connecting power cable to the vehicle battery. The VIBE RT compression fit terminals are
the best way to connect heavy gauge power cable to the vehicles battery.
Model: CT0 – 0 gauge compression fit ring terminal
Model: CT4 – 4 gauge compression fit ring terminal
VIBE RT4 / RT8 crimp on ring terminal
The professional range of VIBE RT gold plated ring terminals for connecting power cable to the vehicle
battery. Packed in pairs and include red and black rubber over boots with are easy crimp design.
Model: RT8 – 1 pair of 8 gauge crimp on ring terminals with PVC overboots
Model: RT4 – 1 pair of 4 gauge crimp on ring terminals with PVC overboots
VIBE AGU30, AGU60, AGU80 fuses
The VIBE AGU fuse series are the perfect companion to the VIBE FD4 fused distribution block and the Active
and stereo system wiring kits.
Model: AGU30 – 1 pair 30 amp AGU fuses to fit all AGU fuse holders
Model: AGU60 – 1 pair 60 amp AGU fuses to fit all AGU fuse holders
Model: AGU80 – 1 pair 80 AGU fuses to fit all AGU fuse holders
All Accessories are available direct, for next day delivery call 0870 765 8423 or vist www.vibeauduo.co.uk/shop (UK ONLY)
For more product info see www.vibeaudio.co.uk
Autogood products Internet store “130”
The CriticalLink™ range of FLAT series cabling from VIBE
The VIBE CriticalLink range of cabling has been developed to achieve the critical link between source (headunit), amplifier and speakers –
VIBE audio equipment is high quality, using anything less than the VIBE CriticalLink™ range of cables will severely compromise your
equipment and will not allow it to perform to its maximum potential.
NOTE: Your audio equipment will only ever be as good as the cables you use to connect it. The link between your audio equipment is critical
for a bigger cleaner sound.
VIBE cabling and interconnects can enhance your system power and sound quality by more
than 20% over other brand cable.
All Accessories are available direct, for next day delivery call 0870 765 8423 or vist www.vibeauduo.co.uk/shop (UK ONLY)
For more product info see www.vibeaudio.co.uk
BASS SYSTEM KIT
The VIBE 3000watt BASS KIT is specifically designed to gain maximum output from high power Bass systems. Featuring the best BASS specific
cables from the VIBE CriticalLink™ Range.
Contents of this Kit:
FLATLINES™ 4AWG PWR Power and Ground cable
FLATBASS™ RCA SolidCore™ Interconnect
FLATBASS™ 13 SPK Bass speaker cable
FLATLINES ™ remote 18
VIBE 140 amp circuit breaker
All cable is terminated with crimped terminal rings in place and accessory fitting kit
COMPATIBILITY
This kit is compatible with the majority of amplifiers on the market – VIBE recommends this kit for all VIBE BASS monoblock amplifiers new, current
and old models.
Model: Bass Kit – Bass specific amplifier wiring kit
STEREO SYSTEM KIT
The VIBE 1500 watt STEREO KIT is specifically designed to gain maximum output from high power full range systems. Combining the best full
range cables from the VIBE CriticalLink ™ range.
Contents of this Kit:
FLATLINES™ 8AWG PWR Power and Ground cable
VIBE FLATSTEREO™ RCA - OFC high definition full range interconnect
FLATLINES ™ remote 18
FLATSTEREO™ speaker cable
AGU Fuse Holder
All cable is terminated with crimped terminal rings in place and accessory fitting kit
COMPATIBILITY
This kit is compatible with the majority of amplifiers on the market – VIBE recommends this kit for all VIBE full range STEREO amplifiers new,
current and old models. FLATLINES™ 8 PWR Power
Model: Stereo Kit – full range stereo amplifier wiring kit
ACTIVE SYSTEM KIT
a
u
.
The VIBE 1500watt ACTIVE BASS KIT is specifically designed to gain maximum output from high power Active Bass systems (Bass Boxes).
Featuring BASS specific components from the VIBE CriticalLink™ range.
Contents of this Kit:
FLATLINES™ 8AWG PWR Power and Ground cable
FLATBASS™ RCA SolidCore™ Interconnect
FLATLINES ™ remote 18
AGU Fuse Holder
FastPlug™
COMPATIBILITY
This kit is compatible with the majority of amplifiers on the market – VIBE recommends this kit for all VIBE active bass enclosures new, current and
old models.
m
o
.c
Model: Active Kit – Bass specific active enclosure wiring kit
The VIBE 1.5 farad power capacitor is a must for any high performance audio system. VIBE’s 1.5 farad power capacitor
bridges the gap between the vehicles battery and the amplifiers ensuring rapid smooth current flow resulting in louder
tighter bass and clean crisp midrange and treble. The built in digital voltage display constantly and accurately displays the
systems DC voltage. An all new VIBE power distribution block is built into the top of the capacitor to allow easy wiring into
the system and also will allow 3 amplifiers to be wired directly to the capacitor for maximum current flow to the amplifiers.
30
Model: PC15
1
The Deltabox line driver is the ideal solution for those looking to install multiple amplifiers from a single RCA preout. Most people use
RCA “Y” splitters for this task unaware of the signal degradation caused. The Deltabox not only divides the signal but also isolates and
boosts the signal up to a maximum of 9 volts independently for each of the 3 output channels giving much cleaner sound and
excellent signal to noise ratio. For SPL competition the Deltabox is an essential tool as each of the outputs can be split 4 times giving
control of 12 amplifiers from a single gain enabling precise adjustment of the system without having to reset every amplifier
individually. Additionally if your headunit has a weak preout or you wish to run multiple amps but only have one output the Deltabox™
is your ideal solution. Model: DELTABOX
The VIBE FastPlug™ (pat. pending), is a product long overdue. Designed and developed by VIBE Engineers the plug
offers safe, fast removal of your active bass enclosure (bass box) or amplifier. You may wish to remove your
system for security reasons, or for the full use of your boot space, whatever the reason the VIBE FastPlug makes
it easy and safe.
The plug is a heavy duty connector that connects positive, negative and remote wires. It is made up of 2 parts –
one end to connect to your equipment and the other to your power source – made from high quality ABS plastic
the device is tough and hard wearing. Model: FASTPLUG
FLATLINES™ Power and Ground Cable
VIBE FlatLines™ power cable has been developed to maximises voltage transfer from battery to amplifier - The cable has 2 main lines
running side by side which are made up of fine copper strands - This design makes the cable flat allowing us to make very slim heavy duty
power cable which is highly flexible easing installation.
Available in: system kits, by the roll or by the metre
Model: FLATLINES 8 PWR – 8gauge red power cable Model: FLATLINES 8 GND – 8gauge black power cable
Model: FLATLINES 4 PWR – 4gauge red power cable Model: FLATLINES 4 PWR – 4gauge red power cable
Model: FLATLINES 0 PWR – 0gauge red power cable Model: FLATLINES 0 GND – 0gauge black power cable
FLATSTEREO™ High Definition full range Interconnect
The VIBE FLATSTEREO RCA is an OFC high definition full range interconnect – delivering the fullest signal possible from source to
amplifier - the cable make up has been developed to run flat with left and right cables running parallel both with individual screening but
sharing an outer FLAT jacket easing installations.
Available in:
Model: FlatStereo RCA 1m – 1 metre full range interconnect
Model: FlatStereo RCA 5m - 5 metre full range interconnect
FLATBASS™ – SolidCore™ Bass interconnect
The VIBE FLATBASS™ interconnect has been specifically developed for use in BASS SYSTEMS - the cable make up has a unique super
FLAT™ design easing installation - Its trick ingredient is oversized SolidCore™ OFC signal wires - allowing a heavier voltage to be passed
down the cable. This is the central wire that caries the main signal from source to amplifier.
Available in:
Model: FlatBass RCA 1m – 1 metre BASS interconnect
Model: FlatBass RCA 5m - 5 metre BASS interconnect
FLATFLEX™ High Definition speaker cable
The delivery of power and signal to the speaker is the final CriticalLink™ in any audio system – VIBES FlatFlex OFC high definition
speaker cable is produced from super fine OFC copper strands collectively picking up all the detail in your music – the multi strands
are aligned in a row making the cable super FLAT™ which can be run invisibly under carpets.
Available in:
Model: FlatFlex 16 SPK – 16 gauge High definition flat flexible speaker cable
Model: FlatFlex 12 SPK – 12 gauge High definition flat flexible speaker cable
Autogood products Internet store “130”