Mitsubishi LaserVue L65-A90 Specifications

MODEL L65–A90
Owner’s Guide
Downloaded From TV-Manual.com Manuals
Downloaded From TV-Manual.com Manuals
For Your Records
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
RETAILER NAME
LOCATION
The lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user of the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
POWER MAINS DISCONNECTION: The main power
plug is used as the disconnect device and must remain
readily accessible.
LASER SAFETY NOTICE
Always inspect the TV for damage after moving it. If
the cabinet or screen is physically damaged, DO NOT
connect the TV to an AC outlet. Call (800) 332-2119 for
assistance.
DO NOT power on the TV until it has been repaired by
qualified service personnel authorized by Mitsubishi
Digital Electronics, America. See “Service and Customer Support” page 6.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
TV WEIGHT: This TV is heavy! Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and disconnect all cables before moving it.
WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.
TV Software
Do not attempt to update the software of this TV with software
or USB drives not provided by or authorized by Mitsubishi
Digital Electronics America, Inc. Non-authorized software may
damage the TV and will not be covered by the warranty.
Downloaded From TV-Manual.com Manuals
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
FCC Declaration of Conformity
Product:
Projection Television Receiver
Model:
L65-A90
Responsible
Party:
Mitsubishi Digital Electronics
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
Telephone:
(800) 332-2119
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/
TV technician for help.
Changes or modifications not expressly
approved by Mitsubishi could cause harmful
interference and would void the user’s authority
to operate this equipment.
4
Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
1)
Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4)
Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.
E XAMP LE OF ANT E NNA G R OUNDING
Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Downloaded From TV-Manual.com Manuals
ANT E NNA
LE AD IN WIR E
G R OUND C LAMP
E LE C T R IC
S E R V IC E
E QUIP ME NT
ANT E NNA
DIS C HAR G E UNIT
(NE C AR T IC LE 810-20)
G R OUNDING
C ONDUC T OR S
(NE C AR T IC LE 810-21)
G R OUND C LAMP S
NE C — NAT IONAL E LE C T R IC AL C ODE
P OWE R S E R V IC E G R OUNDING
E LE C T R ODE S Y S T E M
(NE C AR T 250, P AR T H)
5
Laser Safety
Safe Operation
•
•
Caution. Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Use external or remote controls to operate the
product. Connection to signal sources and power
are accomplished through the external connectors.
Damage and Repair
This label is located on the left lower back of the
television set.
Laser Hazard
•
•
•
•
•
This TV is a CLASS 1 laser product. This TV poses
no risk to eyes or skin during normal use. An exposure hazard may exist only if the protective housing
is removed.
This TV contains a CLASS 4 laser device, which by
itself may be hazardous. However, this TV incorporates a protective housing, optics and electronics
such that there should be no exposure to unsafe
levels of laser light during normal operation and
proper service.
Do not open this product. No consumer controls inside. Only a trained LaserVue™ technician
should service this TV. Please call Mitsubishi at
1-800-332-2119 for assistance.
•
There are no user serviceable components in this
TV. Do not attempt to disassemble any part of the
TV.
If damaged, the device must not be powered or
used until it is repaired by qualified service personnel authorized by Mitsubishi Digital Electronics,
America. See “Service and Customer Support” on
the next page.
Under no circumstances shall attempts be made to
operate this device without the screen in place or if
any portion of the enclosure, including the screen,
is cracked, broken, a liquid is spilled onto the TV or
is otherwise damaged.
CAUTION − CLASS 4 LASER
LIGHT WHEN OPEN AVOID EYE
OR SKIN EXPOSURE TO DIRECT
OR SCATTERED RADIATION
The above two labels are located inside the back cover
of the television in an area that should not be accessed
by the user.
Downloaded From TV-Manual.com Manuals
Contents
Important Information About Your TV
Important Safety Instructions. . . . . . .
Installation and Operating Notes . . . .
. . . . . . . . .
. . . . . . . . .
1 Television Overview
Welcome Kit . . . . . . . . . . . . . . . . . . . . .
Special Features of Your TV. . . . . . . . . . .
TV Control Panel and Convenience Inputs
TV Main Panel . . . . . . . . . . . . . . . . . . . .
4
7
9
. 9
10
12
. . . . . .
. . . . .
. . . . .
. . . . .
2 TV Setup
Guidelines for Setting Up and Using Your New
Widescreen TV . . . . . . . . . . . . . . . . . . . . . .
Initial TV Setup . . . . . . . . . . . . . . . . . . . . . . .
Setting Up TV Inputs. . . . . . . . . . . . . . . . . . .
Controlling A/V Receiver Sound Volume . . . . .
Using the TV with a Personal Computer . . . . .
. .
. .
. .
. .
. .
3 TV Connections
Before You Begin . . . . . . . . . . . . . . . . . . . . . . .
Cable Management . . . . . . . . . . . . . . . . . . . . .
HDMI Device (Cable Box, Satellite Receiver, DVD
Player, or Other Device) . . . . . . . . . . . . . . . . . .
Component Video Device (HDTV Cable Box or
Satellite Receiver, DVD Player, or Other Device) .
DVI Video Device (Cable Box, Satellite Receiver,
DVD Player, or Other Device) . . . . . . . . . . . . . .
S-Video Device (Standard Cable Box, Satellite
Receiver, or Other Device) . . . . . . . . . . . . . . . .
Wall Outlet Cable (no cable box) . . . . . . . . . . . .
Antenna with a Single Lead . . . . . . . . . . . . . . . .
Antennas with Separate UHF and VHF Leads . . .
VCR to an Antenna or Wall Outlet Cable . . . . . . .
VCR to a Cable Box (Audio & Video) . . . . . . . . . .
Older Cable Box . . . . . . . . . . . . . . . . . . . . . . . .
Audio-Only Device . . . . . . . . . . . . . . . . . . . . . .
A/V Receiver (Sound System) Using the TV’s
Audio Output . . . . . . . . . . . . . . . . . . . . . . . . .
A/V Receiver with HDMI Output . . . . . . . . . . . . .
Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
16
16
18
20
22
22
23
23
24
24
25
25
25
26
26
27
27
28
28
29
Service
If you are unable to correct a problem with your TV,
consult Mitsubishi Consumer Relations at (800) 332-2119.
•
DO NOT adjust any controls other than those
described in this Owner’s Guide.
DO NOT remove the protective back cover of your TV.
Downloaded From TV-Manual.com Manuals
. . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . .
5 TV Menus
Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control Keys for the TV Menu System
AV Menu . . . . . . . . . . . . . . . . . . . . . . . . . . .
Captions Menu . . . . . . . . . . . . . . . . . . . . . . .
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . .
Inputs Menu . . . . . . . . . . . . . . . . . . . . . . . . .
Lock Menu. . . . . . . . . . . . . . . . . . . . . . . . . .
6 NetCommand IR Control
About NetCommand IR Control . . . . . . . . . . .
IR Emitter Placement . . . . . . . . . . . . . . . . . .
Initial NetCommand Setup for Most Devices . .
Adding or Removing Device Keys from
NetCommand IR Control . . . . . . . . . . . . . . .
NetCommand Specialized Device Keys . . . . .
Operating NetCommand-Controlled Devices .
Setting Up NetCommand IR Control of an A/V
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . .
. .
. .
. .
. .
. .
. .
. .
. .
. .
. .
39
39
40
45
46
51
52
55
56
57
. .
. .
61
. .
.
.
.
68
69
71
.
78
82
. . . . . . . . . .
88
. . . . . . . . . . . . . . . . . . .
89
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
92
Mitsubishi TV Software.
Index
30
30
31
32
33
34
35
36
38
57
58
59
. .
Appendices
Appendix A: Specifications . . . . . . . . . . . . . . .
Appendix B: Bypassing the Parental Lock . . . .
Appendix C: Programming the Remote Control
Appendix D: NetCommand HDMI Control of
CEC Devices . . . . . . . . . . . . . . . . . . . . . . . .
Appendix E: Troubleshooting . . . . . . . . . . . . .
Trademark and License Information
Service and Customer Support
•
4 TV Operation and Features
Choosing a Viewing Source . . . .
Sleep Timer . . . . . . . . . . . . . . .
Remote Control . . . . . . . . . . . .
ChannelView Channel Listings . .
Status Display . . . . . . . . . . . . .
Fav (Favorite Channels) . . . . . . .
TV Signals and Display Formats.
Viewing Camera Files . . . . . . . .
3D Video . . . . . . . . . . . . . . . . .
Customer Support
• To order replacement or additional remote controls or Owner’s Guides, visit our website at
www.mitsuparts.com or call (800) 553-7278.
• For questions:
- Call Consumer Relations at (800) 332-2119.
- E-mail: MDEAservice@mdea.com
- Website: www.mitsubishi-tv.com
.
7
Installation and Operating Notes
Transportation Screws
Stand and Wall-Mount Requirements
REMOVE AND SAVE TRANSPORTATION
SCREWS BEFORE WATCHING TV
This TV uses four transportation
screws to protect the internal
screen from damage when the
TV is shipped or moved.
CAUTION: Use this Mitsubishi TV model only with the
Mitsubishi stand or wall-mount kit shown here. Other
stands or wall-mounts may damage the TV or result
in instability and possibly cause injury. Contact your
Mitsubishi dealer for information on purchasing a stand
or wall-mount. Mitsubishi recommends you hire a
professional installer to mount the TV on the stand or to
perform the entire wall-mount installation.
1. With the transportation
2.
3.
screws still secured in
place, move the TV as close
as possible to its final
position.
Remove the four transportation screws using
the 5-mm Allen wrench
provided with the accessories.
Slide the four screwhole covers into place.
Step 2
6.
Stand Model
Wall-Mount Kit
L65-A90
LFB-65
LWM-65
NOTE TO CATV SYSTEM INSTALLER: THIS
REMINDER IS PROVIDED TO CALL THE CATV SYSTEM
INSTALLER’S ATTENTION TO ARTICLE 820-40 OF THE
NEC THAT PROVIDES GUIDELINES FOR THE PROPER
GROUNDING AND, IN PARTICULAR, SPECIFIES THAT
THE CABLE GROUND SHALL BE CONNECTED TO THE
GROUNDING SYSTEM OF THE BUILDING, AS CLOSE
TO THE POINT OF CABLE ENTRY AS PRACTICAL.
Moving the TV
•
4. Place the screws, Allen
5.
TV Model
wrench, and the instruction sheet in the clear
plastic bag provided.
Secure the bag to the
back of the TV using the
Step 3
plastic holding pin provided. Otherwise, store
the bag in the Welcome Kit box.
Using care, gently set the TV in its viewing position.
When you move the TV in the future, reinstall the transportation screws to protect
the internal screen.
•
Before moving the TV, reinstall the four transportation screws. See “Transportation Screws” on this
page.
Always inspect the TV for damage after moving
it. If the cabinet or screen is physically damaged,
DO NOT connect the TV to an AC outlet. DO NOT
power on the TV until it has been repaired by qualified service personnel authorized by Mitsubishi
Digital Electronics, America. See “Service and
Customer Support” on the opposite page.
Internal Fans
Internal cooling fans maintain proper operating temperatures
inside the TV. It is normal to hear the fans when you first turn
on the TV and during quiet scenes while viewing the TV.
Holding Pin
Instruction Sheet
5 mm Allen Wrench
4 Transportation Screws
(M6 X 20, 1.0 mm pitch)
Steps 4 and 5
Downloaded From TV-Manual.com Manuals
Note: Features and specifications described in this
owner’s guide are subject to change without notice.
8
Cleaning Recommendations
Screen
Normally, light dusting with a dry, non-scratching duster
will keep your TV clean. If cleaning beyond this is
needed, please use the following guidelines:
First turn off the TV and unplug the power cord from the
power outlet.
Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using a
vacuum cleaner with a brush attachment.
•
Top and Sides of the TV
General Cleaning Precautions
•
•
•
Without applying pressure, gently wipe down your
TV with a soft, non-abrasive cloth such as cotton
flannel or a clean cloth diaper, lightly moistened
with water. Dry with a second dry, soft, non-abrasive cloth.
For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water
used to moisten the cloth. Rinse with a second
cloth moistened only with water. Dry with a third
dry, soft, non-abrasive cloth.
Glossy Surfaces
Use the soft cleaning cloth supplied with the TV.
• Clean the cloth before each use by shaking or
brushing to remove any residual dirt particles.
• Gently wipe down the glossy surfaces of your TV with
the soft cloth. Do not apply pressure while wiping.
• If necessary, lightly dampen the soft cloth with
water. Do not use chemical or abrasive cleaners.
• Wash the soft cloth by hand or machine. Use only
mild soap.
Downloaded From TV-Manual.com Manuals
•
•
•
•
•
•
•
Follow the instructions for the top and sides, wiping
gently in an up and down motion.
Clean the entire screen evenly, not just sections of
the screen.
Do not allow liquid to drip down the screen, as
some liquid may enter the TV through the gap
between the screen and screen frame.
You may purchase Mitsubishi Screen Cleaner, part
number CLEANER-VSS, by calling (800) 553-7278.
DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
DO NOT scrub or rub the TV harshly. Wipe it gently.
1
Television Overview
Welcome Kit
maintain them at 1080p through all processing until
displayed.
Please take a moment to review the following list of
items to ensure that you have received everything.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Remote Control
Two AA Batteries
Owner’s Guide
Quick Reference Guide
Quick Connect Guide
Product Registration Card
Four-Ended IR Emitter
Cleaning Cloth for Glossy
Surfaces (see instructions
under “Cleaning Recommendations,” page 8.
5-mm Allen Wrench (see
“Transportation Screws”
page 7)
Plastic Storage Bag (for
transportation screws)
Holding Pin (for plastic
storage bag)
Cable Tie with Pin
3D Ready
AA
AA
1
Integrated HDTV Tuner
7
Your widescreen Mitsubishi HDTV has an internal HDTV
tuner able to receive both over-the-air HDTV broadcasts
(received via an antenna) and non-scrambled digital
cable broadcasts, including non-scrambled HDTV cable
programming.
8
High-Definition Video Inputs
11
9
•
10
12
13. Storage Box for Welcome Kit
Special Features of Your TV
Welcome to LaserVue TV! Mitsubishi has created a
new category of television with laser technology. Laser
beams provide the widest range of rich, complex
colors, along with the most clarity and depth of field.
Precise and focused, the purity of laser light far surpasses current high-definition technologies and sets a
new standard for premium large-screen television.
Your new high-definition widescreen television has
many special features that make it the perfect center of
your home entertainment system, including:
1080p High-Definition DLP Display System
Your Mitsubishi HDTV uses Texas Instruments Digital
Light Processing™ technology for rear-projection TVs
to create the picture you see on screen. All images
are displayed at 1080p. The TV uses Plush 1080p® to
convert lower-resolution signals to 1080p for display.
The TV can also accept 1080p original signals and
Downloaded From TV-Manual.com Manuals
All Mitsubishi 1080p DLP HDTV’s are 3D Ready. This
feature lets you experience the new 3D technologies
applied to many recent movies and video games.
Immerse yourself in your favorite video game, movie, or
sporting event displayed in 3D.
•
Component Video Inputs. Also called Y/Pb/Pr
inputs, these inputs receive standard analog video
formats of 480i, 480p, 720p, and 1080i high-definition signals. This provides a high level of flexibility
when connecting DVD players/recorders, cable
boxes, and satellite receivers.
HDMI Inputs. These inputs accept digital 480i,
480p, 720p, 1080i, and 1080p video signals plus
PCM digital stereo signals. The HDMI™ inputs can
also accept a variety of PC signals and resolutions.
These inputs support HDMI 1.3 Deep Color (up to
36 bits) and the x.v.Color extended color gamut.
Used with an adapter, these inputs also accept
compatible digital DVI video signals. HDMI inputs
provide additional high-performance, high-definition
connections for maximum flexibility in your choice
of home theater products. The HDMI inputs are
HDCP copy-protection compatible.
Easy Connect Auto Input Sensing
Easy Connect™ Auto Input Sensing automatically recognizes when you plug in an input and prompts you to
assign a name to it. The TV ignores any unused inputs,
so the result is an uncluttered Input Selection menu
where you can easily find and select connected devices
by name.
9
10
1. Television Overview
Home Theater Control
customized NetCommand-controlled home-theater
system.
NetCommand with IR Learning
NetCommand for HDMI
Your Mitsubishi HDTV offers a new level of networking
that seamlessly integrates selected older A/V products
with new and future digital products. NetCommand®
supports IR (infrared) control of products such as
VCRs, DVD players, cable boxes, and satellite receivers. NetCommand can “learn” remote control signals
directly from many devices, allowing you to create a
HDMI devices with Consumer Electronics Control (CEC)
capabilities may be compatible with the TV’s NetCommand for HDMI feature. Compatible devices can
receive control signals through the HDMI connection.
You may be able to operate some functions of these
devices using the TV’s remote control.
TV Control Panel and Convenience Inputs
POWER
Control Panel. Touch keys on the control panel briefly
illuminate when pressed or when the TV is powered
on. The touch keys duplicate some keys on the remote
control.
SYSTEM RESET
SYSTEM RESET and POWER
buttons on the front panel
Convenience Inputs
Control Panel
Touch keys on the control panel duplicate commonly
used keys on the remote control. The upper labels
show control functions when no TV menus are displayed; the lower labels indicate functions when TV
menus are displayed or when a special function has
been activated. See “Remote Control,” page 31, for
more on these functions.
A/V Reset
If you wish to reset the A/V (Audio/Video) settings back
to the factory defaults:
• To reset all settings at once, press GUIDE and FORMAT
on the control panel at the same time.
• To reset the defaults for individual inputs, use the
Reset selection on the AV menu. See “AV Menu,”
page 40.
INPUT 4 is a readily accessible set of input jacks for a
camcorder, game, or other audio/video device.
• To view NTSC/480i composite video signals, plug
the single composite video cable (usually yellow)
into the VIDEO/Y jack.
• To view Y Pb Pr component video in 480i, 480p
720p, or 1080i format, connect cables to the Y/
VIDEO, Pb and Pr jacks.
• Plug stereo audio cables into the AUDIO
L and R jacks for sound from connected
devices. You can use the audio jacks for
sound from an audio device playing while
USB
viewing photos from the USB input.
• A USB photo port lets you view JPEG
images from a USB drive or card reader.
INPUT 4
System Reset Button
If the TV fails to respond to the remote control, control
panel touch keys, or will not power on/off, press the
SYSTEM RESET button on the control panel.
The blue power LED on the front panel will flash quickly
for up to one and a half minutes. When the blue LED
stops flashing, you may turn on the TV. Recent setting
changes you made before using SYSTEM RESET may be lost.
Downloaded From TV-Manual.com Manuals
L
R
Y/
VIDEO
Pb
Pr
TV Side
1. Television Overview
11
Front-Panel Indicators
Front Panel Indicators
1. STATUS indicator. Off during normal TV operation.
2. POWER indicator. Lit when TV is powered on;
flashes slowly when TV is powered off and the
auto-on TV Timer is set. Flashes quickly immediately after the TV has been plugged into a power
outlet.
POWER and STATUS
Indicator LEDs
Off
Steady On
Slow Blinking
Fast Blinking
POWER Indicator
LED Color TV Condition
Additional Information
None
TV is powered off.
Normal operation.
Blue
TV is powered on.
Normal operation.
Blue
TV powered off, auto-on timer is set. Normal operation. TV can be turned on at any time.
Blue
•
•
TV just plugged into AC outlet.
Wait approximately two minutes for blinking to stop before
turning
on. Normal operation.
AC just restored after power failure.
•
TV is rebooting after System
Reset used.
•
TV is rebooting after power
fluctuation or receiving abnormal digital signals from a digital
channel or digital device.
•
You have begun the procedure
to update software from an
authorized flash memory device.
STATUS Indicator
LED Color TV Condition
Additional Information
None
Normal TV on or standby condition.
Normal operation.
Yellow
TV is too hot.
The TV will display a warning message and shut off if it overheats.
•
•
Red
TV may require service.
Downloaded From TV-Manual.com Manuals
Ambient room temperature may be too high. Turn off the TV
and let the room temperature drop.
Clear blocked air vents. Ensure at least a four-inch clearance on all sides of the TV.
Turn off the TV and unplug the set from the AC power source.
Wait one minute and then plug the set back in. See Appendix E.
If the LED is still on, contact your dealer or a Mitsubishi Authorized Service Center. Go to www.mitsubishi-tv.com or call
1-800-332-2119 to receive Authorized Service Center information.
12
1. Television Overview
TV Main Panel
1. ANT 1/ANT 2 (Antenna)
ANT-2/AUX
ANT-1/MAIN
If you are connecting an antenna or direct cable service
without a cable box, connect the main antenna or cable
source to ANT 1. Use ANT 2 for a second source.
1
ANT 1 and ANT 2 can each receive digital and analog
over-the-air channels from a VHF/UHF antenna or nonscrambled digital/analog cable source.
5
L - AUDIO - R
INPUT 3
6
L - AUDIO - R
DVI/PC INPUT
R
AVR AUDIO
OUTPUT
L
R
DIGITAL
AUDIO OUTPUT
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
S-VIDEO
(INPUT 3)
4
VIDEO
L
R
9
INPUT 2
Pr
Pb
L
Y
Pr
These are analog stereo inputs.
• Use the INPUT 1 stereo audio jacks with INPUT 1
composite video (single yellow cable) or INPUT 1
component video (Y Pb Pr cables).
• INPUT 2 stereo audio jacks are for use exclusively
with INPUT 2 component video.
Pb
3. AUDIO L and R (INPUT 1, INPUT 2)
3
YPbPr(480i/480p/720p/1080i)
INPUT 1 also accepts composite video on the Y/VIDEO
jack. See item 5 below.
2
Y/VIDEO
Y Pb Pr Component Video (480i/480p/720p/1080i)
Use these jacks to connect devices with component
video outputs, such as DVD players, external HDTV
receivers, or compatible video game systems. Use the
adjacent AUDIO R and L jacks for INPUT 1 or INPUT 2
if you wish to send audio to the TV. See Appendix A
specifications for signal compatibility.
INPUT 1
2. Component Video (INPUT 1, INPUT 2)
8
10
11
4. S-VIDEO (INPUT 3)
3D GLASSES EMITTER
7
3
12
13
4
6. AUDIO L and R (INPUT 3)
2
Use one of the jacks labelled VIDEO (or Y/
VIDEO on INPUT 1) to connect composite video
from a VCR, DVD player, standard satellite
receiver, or other A/V device to the TV. Use
the nearby AUDIO R and L inputs for INPUT 1 or INPUT 3
if you wish to send audio to the TV. Note that the INPUT
3 composite video jack is automatically disabled when
you connect to S-VIDEO (item 4).
RS-232C
5. Composite Video (INPUT 1, INPUT 3)
VIDEO: 480i/480p/720p/1080i/1080p
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p, 1080p
1
Connect an S-Video device to this input. Use
the AUDIO R and L jacks for INPUT 3 (item 6) if
you wish to send audio to the TV.
Use INPUT 3 stereo audio jacks with the nearby INPUT 3
composite video jack or with the S-VIDEO jack (item 4).
7. HDMI™ Inputs (High-Definition
Multimedia Interface)
The HDMI inputs support uncompressed standard and
high-definition digital video formats and PCM digital
stereo audio.
Downloaded From TV-Manual.com Manuals
Use the HDMI inputs to connect to CEA-861 HDMI compliant devices such as a high-definition receiver or DVD
player. These inputs support 480i, 480p, 720p, 1080i,
and 1080p video formats.
1. Television Overview
13
TV Back Panel, continued
Mitsubishi recommends you use category 2 HDMI cables,
also called high-speed HDMI cables, to connect HDMI
1.3 source devices. High-speed category 2 cables bring
you the full benefits of Deep Color and x.v.Color.
DVI Video. The HDMI inputs can also accept digital DVI
video signals.
• To connect a device’s DVI output to the TV’s HDMI
input, use an HDMI-to-DVI adapter or cable plus
analog audio cables.
• Connect the analog audio cables to the DVI/PC
INPUT AUDIO jacks (item 8) on the TV to receive left
and right stereo audio from your DVI device.
• The TV’s HDMI inputs are compatible with many
DVI-D and HDMI computer video signals. For additional information on PC compatibility, see “Using
the TV with a Personal Computer,” page 20, and
Appendix A , “Specifications,” page 68.
These inputs are HDCP (High-Bandwidth Digital Copy
Protection) compliant.
These inputs are
certified for proper interoperability with other products certified by Simplay™.
8. DVI/PC INPUT AUDIO
Use the DVI/PC INPUT AUDIO jack when connecting
a DVI device to one of the TV’s HDMI inputs using a
DVI-to-HDMI cable. These jacks allow you to send left
and right analog audio from your computer or other DVI
device to the TV.
HDMI Cable Categories
HDMI cables are available as Category 1 and Category 2 types.
• Category 2 Cables (also called high-speed
HDMI cables). Newer, HDMI 1.3-compliant DVD
players, video games, and set-top boxes require
Category 2 cables, suitable for clock frequencies up to 340 MHz or data rates of up to 10.2
gigabits per second. Use category 2 cables for
high-speed 1080p HD signals carrying extended
color encodings (i.e., 30 or more bits, also called
Deep Color). Category 2 cables are also suitable
for standard HDTV signals.
• Category 1 Cables (also called standard HDMI
cables). Category 1 cables may be unmarked.
They are suitable for standard HDTV 720p,
1080i, and 1080p signals with 8-bit color depth.
Use category 1 cables for clock frequencies up
to 74.25 MHz or data rates of up to 2.23 gigabits
per second.
Downloaded From TV-Manual.com Manuals
9. DIGITAL AUDIO OUTPUT
Depending on the source, this output sends either Dolby
Digital or PCM digital audio to your digital A/V receiver.
If you have a digital A/V receiver, in most cases this is the
only audio connection needed between the TV and your
A/V receiver.
10. AVR AUDIO OUTPUT
Use AVR AUDIO OUTPUT to send analog audio of the
program currently shown on the screen to an analog
A/V surround sound receiver or stereo system. Digital
audio from digital channels and HDMI devices is converted to analog audio by the TV. This is the only audio
connection needed between it and the TV if using an
analog A/V receiver or stereo system.
11. IR NetCommand Output/External
Controller Input
IR emitters connected to this jack are used by the TV’s
NetCommand system to send control signals to external
IR remote-controlled devices such as cable boxes, VCRs,
DVD players, satellite receivers and audio receivers.
When NetCommand is not in use, this jack can be switched
to receive wired IR control signals from external system
controllers. To switch this jack to an input, connect the
external controller’s IR output to this jack, then:
1. Press MENU to display the TV menu.
2. Enter the number sequence 2, 4, 7, 0 to display the
Installer menu.
3. Highlight the WIRED IR selection and press ENTER to
change the setting from OFF to ON.
To revert to NetCommand control:
1. Disconnect the IR device.
2. Press MENU to display the TV menu.
3. Enter the number sequence 2, 4, 7, 0 to display the
Installer menu.
4. Highlight the WIRED IR selection and press ENTER to
change the setting from ON to OFF.
Note: When the WIRED IR option is set to ON (control
by an external device), the Low Power setting
for Energy Mode is unavailable.
12. RS-232C
Use the RS-232C interface to receive control signals
from compatible home-theater control devices.
13. 3D GL ASSES EMITTER
Use this jack to connect the special IR emitter supplied
with 3D glasses. The emitter will send a signal that
synchronizes your 3D glasses with the screen display.
14
2
TV Set-Up
Guidelines for Setting Up and Using Your New Widescreen TV
Getting Started
1. Check the TV cabinet for damage. If there is
damage, do not plug in the TV. Call Mitsubishi
Consumer Relations at (800) 332-2119.
2. Review the important safety, installation, and oper3.
ating information at the beginning of this book.
Choose a location for your TV.
•
•
•
•
Allow at least four inches of space on all sides
of the TV to help prevent overheating. Overheating may cause premature failure of the TV.
Avoid locations where light may reflect off the
screen or where the TV is exposed to direct
sunlight.
See the stand and wall-mount requirements
under “Installation and Operating Notes,” page
7.
Remove the four transportation screws
before final positioning of the TV. Keep the
screws in the storage bag provided and
reinstall them whenever moving the TV.
4. Install the batteries in the remote control. See page
Installing the Remote Control
Batteries
1. Remove the remote control’s back cover by
gently pressing in the tab and lifting off the
cover.
2. Load the batteries, making sure the polarities
(+) and (-) are correct. For best results, insert
the negative (-) end first.
3. Snap the cover back in place.
1
The remote
control requires
two AA alkaline
batteries.
2
31 for more on use of the remote control.
IMPORTANT
Do not plug the TV into a power outlet if there is
visible damage to the screen or cabinet.
5. Plug your TV into a power outlet. The blue power
6.
7.
LED on the front of the TV will start blinking rapidly.
After the blue LED stops blinking, press the POWER
key to power on the TV.
When the Welcome screen appears the first time
you power on the TV, select a language for TV
menus. You can later change the language through
the Setup menu.
Connect your audio/video (A/V) devices to the TV
and perform initial setup.
• See the following pages for initial TV setup and
use of the Auto Input Sensing feature.
• See chapter 3, “TV Connections,” for connection diagrams.
Downloaded From TV-Manual.com Manuals
Turning the TV On or Off
To turn the TV on or off, point the remote control
at the front of the TV and press the POWER key.
Alternatively, press the POWER button on the TV’s
control panel.
When You First Power On the TV
Choosing a Language for Menus
1. Power on the TV for the first time.
2. Press
to select either English or Spanish
for all menus. You can later change the language selection through the Setup > Language menu. See page 46.
2. TV Setup
15
Guidelines for Setting Up and Using Your New Widescreen TV, continued
•
8.
9.
To connect the TV to a personal computer, see
“Using the TV with a Personal Computer,” page
20.
• Home-theater control can be set up after detection of each device or can be postponed until
any convenient time afterward.
- See chapter 6, “NetCommand IR Control,”
to set up IR control of your home theater.
- If you plan to use CEC-compatible devices
with the TV’s NetCommand for HDMI
feature, review Appendix D.
Perform a channel scan for channels received on
ANT 1 and ANT 2 if you plan to watch over-the-air
broadcasts or broadcasts received over direct
cable. See “Memorizing Channels,” page 16.
You can now start watching TV or you can perform
additional setup and customization through the TV
menus.
2. To set up or change home-theater control:
•
•
•
TV Operation
1. Review chapter 4, “TV Operation and Features,” for
Additional TV Setup
1. Review chapter 5, “TV Menus,” to customize TV
operation. Press the MENU key to enter the menu
system. Some examples of settings you may wish
to change include:
• Fav. Use an on-screen menu to create custom
lists of your favorite channels from ANT 1 and
ANT 2. See Setup > Edit, page 47.
• Order. Rearrange the device icons in the Input
Selection menu to put frequently used icons
near the front. See Inputs > Order, page 51.
• Name. Change the device types that appear
in the Input Selection menu. See Inputs >
Name options, page 51.
• Parental Locks. Restrict TV viewing by
program rating, by channel, or by time of day.
You can also disable the control-panel touch
keys if you have small children.
- To restrict TV use by program rating, see
the Lock > Parent menu, page 53.
- To lock the control-panel touch keys, use
the Lock > Control Panel menu, page 54.
- To restrict TV use by channel, see Setup >
Edit > Lock, page 47.
• Video Settings. Change video adjustments to
get the best picture for your viewing conditions.
See “AV Menu,” page 40 and “Video Menu,”
page 42.
Note:
You may wish to change the Picture Mode to
either Bright or Natural, which are suitable for
most home viewing.
Downloaded From TV-Manual.com Manuals
For NetCommand IR control of A/V devices,
refer to chapter 6.
If you plan to use CEC-compatible devices with
the TV’s NetCommand for HDMI feature, review
Appendix D.
To program the remote control to operate
A/V devices not under NetCommand control,
see Appendix C, “Programming the Remote
Control.”
2.
3.
TV features including:
• Remote Control. For use of the remote
control, see page 31.
• Input Selection (viewing source). Select a
connected program source to watch, such as a
VCR, DVD player, or antenna. Press INPUT on the
remote control to select from icons for the TV
inputs. See “Choosing a Viewing Source,” page
30.
• Listings. Press GUIDE for ChannelView™
display of listings on ANT 1 and ANT 2, see
“ChannelView Channel Listings,” page 32.
• Picture Formats. Press FORMAT to cycle through
picture sizes and shapes to find the one best
suited to the current program. See “TV Signals
and Display Formats,” page 35.
To view still and moving digital camera images on
the TV, see “Viewing Camera Files,” page 36.”
To control A/V devices with NetCommand, see
page 59, “Operating NetCommand-Controlled
Devices.”
TV Care and Customer Assistance
•
•
•
For general cleaning, see “Cleaning Recommendations,” page 8.
For troubleshooting, service, and product support,
see Appendix E.
For warranty information, see the TV warranty on
page 90.
16
2. TV Setup
Initial TV Setup
Memorizing Channels
For Reception on ANT 1 and ANT 2
To start channel memorization
1. Connect the incoming cable to ANT 1 or ANT 2.
This is the cable from an antenna or a cable service
without a cable box.
2. Press MENU to open the Main menu.
3. Press
4.
to highlight the Setup icon and display the
Setup menu.
With the Setup menu displayed, press to highlight the Scan icon.
More Setup Options
See chapter 5, “TV Menu Settings,” to:
• Set the TV clock (page 48)
• Set the TV Timer (page 49) to have the TV power on
at a preset time.
• Select an Energy Mode to manage power use while
the TV is off (page 50).
• Enable 3D video (page 38).
Setting Up TV Inputs
When You First Connect a Device
The TV’s Easy Connect™ Auto Input Sensing feature
detects most connections automatically.
Note:
For connection and setup of a personal computer, see the information on page 20.
Auto Input Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connection and automatically switch
to the input
b. Prompt you to identify the device type (if not
recognized automatically)
c. Prompt you to perform NetCommand IR setup
for the device, if available
d. Repeat these steps for any additional newly
detected devices
Start channel memorization from the Setup menu.
5. Press
to highlight an input selection based on
your connections:
See below for connections which trigger Auto Sensing.
Input
Condition
Ant 1 Air
Ant 2 Air
When connected to an indoor or
outdoor antenna
Auto Input Sensing Available
Ant 1 Cable
Ant 2 Cable
When connected to direct cable (no
cable box)
Y/VIDEO plus Pb (detected as component video)
6. Press to highlight the on-screen START button.
7. Press ENTER to start automatic channel memoriza-
8.
tion.
To stop channel memorization before
completion, press CANCEL.
When memorization is complete you can:
• Press MENU once to return to the top row of icons.
• Press MENU again to return to the Main menu.
• Press EXIT to watch TV.
After channels have been memorized:
• To tune to memorized channels, press CH
/
while watching TV on the ANT 1 or ANT 2 input.
• Use the Setup > Edit menu (page 47) for additional
channel options, such as adding or deleting channels from memory, naming channels, and saving
favorite channels in custom memory banks.
Downloaded From TV-Manual.com Manuals
Y/VIDEO (detected as composite video)
S-VIDEO
HDMI
*
USB (USB photo port)
INPUT 4 AUDIO (for an audio-only device; see page 27.)
Auto Output Sensing Available
DIGITAL AUDIO OUTPUT (orange jack)
AVR AUDIO OUTPUT (red jack)
No Auto Sensing
ANT 1 and ANT 2
*
If the HDMI device is powered off when connected,
detection occurs when the device is next powered on.
Auto Input Sensing for CEC-Enabled Devices
When the TV’s NetCommand for HDMI feature is enabled,
most CEC-enabled devices are recognized and identified
automatically by the TV. NetCommand for HDMI may
allow you to control functions of a CEC-enabled device.
See Appendix D, “NetCommand HDMI Control of CEC
Devices,” page 78.
2. TV Setup
Setting Up TV Inputs, continued
Auto Input/Auto Output Sensing Screens
See below for how different connections are handled
by Auto Input/Auto Output Sensing.
Setup Procedure for TV Inputs
1. Power on the TV.
2. Connect your devices to the TV, making note
•
Most Device Types. Select the device type from
the on-screen list. The device type you select here
will appear as an icon in the Input Selection menu.
Press
to highlight the device type connected
to the input. Some device types also display a
sub-menu of names—useful if using more than one
of the same device type. See the sample Auto
Input Sensing screen shown.
•
A/V Receiver
- The TV detects audio connections on the
DIGITAL AUDIO OUTPUT jack and the right (red)
AVR AUDIO OUTPUT jack.
of which TV input is used for each device. See
chapter 3, “TV Connections.”
Note:
If you wish to use an HDMI device’s CEC capabilities, follow the steps in Appendix D.
3. When the TV detects a new connection, the Auto
Sensing screen for the connection type will display.
Select the device type if required.
-
•
First select a
device type.
Next perform
IR “learning.”
Sample Auto Input Sensing screen.
Important Note for NetCommand IR Users
Be sure to select the correct device type here. Although
you can change the device type later in the Inputs > Name
menu, any “learned” NetCommand IR codes will be erased
when you make the change.
4. You can perform NetCommand IR “learning” after
selecting the device type or at a later time when
convenient. To perform now, highlight the Learn
icon and press ENTER. See “Initial NetCommand
Setup for Most Devices,” page 57 or “Setting Up
NetCommand IR Control of an A/V Receiver,” page
61.
5. Press EXIT to close the Auto Sensing screen. The
6.
TV will then display the Auto Sensing screen for
the next connection it finds.
After completing Auto Input/Auto Output Sensing,
you may wish to set up or change control of your
equipment using one of the home-theater control
methods described in this Owner’s Guide. See
“About Home-Theater Control Systems” on page
19.
Downloaded From TV-Manual.com Manuals
17
For an HDMI connection, select AVR from
the list of device types if the A/V receiver is
not recognized automatically.
HDMI Devices Compatible with the TV’s
NetCommand for HDMI Feature. Compatible
CEC-enabled HDMI devices are often recognized
automatically by the TV. After connecting the
device, you may briefly see the standard Auto
Input Sensing screen before the TV recognizes
the device type. See Appendix D.
18
2. TV Setup
Controlling A/V Receiver Sound Volume
Setting Up TV Inputs, continued
Tips on Auto Sensing and Changing
Connected Devices
•
•
•
Choose a different name for each input.
Antenna inputs (ANT 1/ANT 2) are never detected,
although you can turn off unused antenna inputs in the
Inputs > Name menu.
You can change the device type displayed in the Input
Selection menu by using the Inputs > Name menu (page
51). Any “learned” NetCommand IR codes will be erased,
however.
Use one of the methods below to control sound volume from
the A/V receiver.
With a Standard TV Setup
•
•
Recommended Method: Program the TV’s
remote control for your A/V receiver and enable the
Audio Lock feature. See page 72.
Program the TV’s remote control for your A/V
receiver and set the TV remote’s slide switch to the
AUDIO position to control A/V receiver volume. Set
the switch back to the TV position to control the TV.
Use the remote control that came with the A/V
receiver.
Changing Devices on an HDMI Input
•
1. Disconnect the HDMI device.
2. Delete the HDMI input in the Inputs > Name menu.
With NetCommand IR Control
3.
See page 51.
Connect the new device and the Auto Input
Sensing screen will display. If you want the device
under NetCommand IR control, perform NetCommand “learning” for the new device.
Disconnecting an Analog A/V Receiver
When you disconnect an analog A /V receiver, be sure
to change the Speakers setting to TV to:
• Hear sound from the TV speakers.
• Redisplay the Auto Output Sensing screen when
you reconnect a device to the AVR AUDIO OUTPUT.
Change the setting using the remote control’s AUDIO key
or the AV > Audio > Speakers menu.
Downloaded From TV-Manual.com Manuals
Set up NetCommand control of the A/V receiver’s
volume functions in the Inputs > AVR menu. The TV’s
remote will then control A/V receiver volume. See page
61.
With NetCommand for HDMI (CEC-Enabled
HDMI A/V Receiver)
The TV’s remote control may control some functions
of the A/V receiver. See “About Home-Theater Control
Systems” on the opposite page and Appendix D,
“NetCommand HDMI Control of CEC Devices,” page
78.
19
2. TV Setup
About Home-Theater Control Systems
This summary offers some examples of the control methods available using the TV’s remote control. You may
wish to use one or more of these methods in your home theater after completing Auto Input Sensing.
Source device connected directly to the TV
Remote Control Programming with Any Connection Type
Program the remote control to operate the A/V device. To control the device, set
the slide switch to the correct position for the device type. See Appendix C, “Programming the Remote Control.” In the case of an A/V receiver, use the Audio Lock
feature, page 72.
NetCommand IR Control with Any Connection Type
Set up NetCommand IR control of the device’s keys as desired. See “IR Emitter
Placement,” page 56, and “Initial NetCommand Setup for Most Devices,” page 57.
CEC-Enabled HDMI Device with HDMI Connection Only
1. Turn on the TV’s NetCommand for HDMI feature. See the instructions in Appendix D, “NetCommand HDMI Control of CEC Devices,” page 78.
2. Experiment with the TV’s remote control (slide switch set to TV) to determine
which device functions it can operate.
Any Connection Type
A/V
Device
TV
Any Connection Type
A/V
Device
TV
HDMI
Cable
CEC-Enabled
A/V Device
TV
Source device connected to an A/V receiver connected to the TV
A/V Receiver with HDMI Output (no CEC)
1. Assign the device to an A/V receiver input to allow you to set up NetCommand
IR control of the A/V receiver’s keys as desired. See “IR Emitter Placement,”
page 56, and “Setting Up NetCommand IR Control of an A/V Receiver,” page
61.
2. Set up NetCommand IR control of the source device’s keys as desired. See
“Initial NetCommand Setup for Most Devices,” page 57.
CEC-Enabled HDMI A/V Receiver
1. Turn on the TV’s NetCommand for HDMI feature. See the instructions in Appendix D, “NetCommand HDMI Control of CEC Devices,” page 78.
2. Try using the TV’s remote control to operate the A/V receiver’s volume and mute
functions.
3. If the source device you want to connect also has CEC capability, see Appendix
D for setup.
4. Try using the TV’s remote control to determine which device functions it can
operate. For example, on a CEC-enabled DVD player, check for a response
to the
(PLAY),
(PAUSE), and
(STOP) keys. For a cable box, check for a
response to CH/PAGE
/ .
5. If desired, set up NetCommand IR control to add commands not supported by
CEC. See chapter 6, “NetCommand IR Control.”
Downloaded From TV-Manual.com Manuals
Source
Device
Any Connection Type
A/V Receiver
HDMI
Cable
TV
CEC-Enabled
Source Device
HDMI
Cable
A/V Receiver
HDMI
Cable
TV
20
2. TV Setup
Using the TV with a Personal Computer
Connecting a Computer to the TV
VIDEO
L - AUDIO - R
INPUT 3
DVI/PC INPUT
L - AUDIO - R
L
R
AVR AUDIO
OUTPUT
L
R
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
RS-232C
AUDIO: PCM STEREO
3D GLASSES EMITTER
VIDEO: 480i/480p/720p/1080i/1080p
2.
2.
INPUT 2
Pr
IMPORTANT
This TV accepts digital computer signals only.
Pb
No additional
audio connection is required.
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
HDMI-to-HDMI
cable
R
TV main
panel
3.
Y
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
Stereo audio
cables
Note: If the computer’s audio output
is a single mini jack, a mini audio-toRCA-male “Y” adapter cable is also
required.
HDMI
INPUT 1
DVI-to-HDMI cable
or an HDMI cable
with an HDMI-toDVI adapter
Audio
Connection
Y/VIDEO
Digital DVI
Video Connection
DVI/PC INPUT
L - AUDIO - R
Computer
Video Output
ANT-2/AUX
ANT-1/MAIN
3.
Use one of the connection methods listed below based
on your computer’s video output.
Computer with
DVI and stereo
audio outputs
1. See the TV specifications in Appendix A to confirm
2.
3.
ANT-2/AUX
ANT-1/MAIN
VIDEO
INPUT 2
L - AUDIO - R
INPUT 3
Pr
R
R
DVI/PC INPUT
L - AUDIO - R
L
AVR AUDIO
OUTPUT IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
L
DIGITAL
AUDIO OUTPUT
Downloaded From TV-Manual.com Manuals
2.
Pb
If your computer provides digital audio
output (coaxial or digital), you can connect it
directly to a digital A/V receiver and bypass
the TV.
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
Note:
2.
Y
6.
Computer with
HDMI audio/video
output
INPUT 1
5.
A DVI connection from a personal computer requires
a separate audio connection. Computer connected to
the TV main panel is shown above.
Y/VIDEO
4.
that your computer signal is compatible with the TV.
Connect the computer’s digital signal output to one
of the TV’s HDMI jacks. See the connection diagrams for the method suited to your equipment.
Connect the computer’s audio output using one of
these options:
• For digital DVI signals, connect analog left/right
audio to the TV’s DVI PC AUDIO INPUT jacks.
• For HDMI signals, no additional audio connection is required.
Power on the TV and computer. The TV will detect
the connection and display the Auto Input Sensing
screen.
In the Auto Input Sensing screen, press
to
highlight PC in the list of device types. It is important to use the name PC so that the TV can process
the video signal correctly.
Press EXIT to close the Auto Input Sensing screen.
TV main
panel
An HDMI-to-HDMI connection carries all video and
audio on a single cable.
21
2. TV Setup
Using the TV with a Personal Computer
Computer Video Adjustments
1. Power on the computer if it is not already on.
2. Select PC from the Input Selection menu. To do
this, press INPUT to open the Input Selection menu,
move the highlight to the PC icon, and press ENTER.
Tip:
Set the computer’s screen saver to display a pattern
after several minutes of inactivity. This acts as a
reminder that the TV is powered on.
3. Working from the computer, change the resolution
4.
of the computer image. View the computer image
on the TV and maximize the computer resolution
while maintaining a suitable aspect ratio for the
image.
Computer Display Formats
Perform TV video adjustments. Press
VIDEO repeatedly to access videoPress the FORMAT key repeatedly to cycle through the TV displays
adjustment options. The following
available for your computer’s video signal.
additional adjustments are available
for computer video:
Computer Signal
As Displayed on TV Screen
Horiz Position (Horizontal Position).
4X3
16 X 9
Original Format
Zoom
Manually adjust the horizontal
Standard
Standard
position.
VGA
Vert Position (Vertical Position).
640 X 480
Manually adjust the vertical position.
5. Press FORMAT repeatedly to find the
picture format best suited to the
image. See the chart on this page
showing how different computer resolutions can be displayed on the TV.
Image Resolution
Your Mitsubishi TV can display resolutions
from standard VGA (640 x 480) through
1920 x 1080 signals at a refresh rate of
60 Hz. See Appendix A , “Specifications”
(page 68) for more on compatible screen
resolutions.
In most cases, the computer will select
the best resolution match to display on
the TV. You can override this setting if you
wish. Refer to your computer operating
system’s instructions for information on
changing the screen resolution.
You may need to restart the computer for
changes to take effect.
WVGA
848 X 480
SVGA
800 X 600
WSVGA
1064 X 600
Original Format
Zoom
Standard
Reduce
XGA
1024 X 768
PC 720p
1280 X 720
WXGA
1360 X 768
SXGA
1280 X 1024
Original Format
PC 1080p
1920 X 1080
Downloaded From TV-Manual.com Manuals
Standard
22
3
TV Connections
Before You Begin
Auto Input Sensing
Surround Sound
The TV’s Auto Input Sensing feature automatically recognizes most connections and prompts you to identify
the type of device connected. See page 16 for more on
Auto Input Sensing.
For best surround sound audio quality, route audiosignal cables or HDMI cables from the source device
directly to your A/V receiver or sound system.
Connection Types
Review the connection types available on your input
devices and use connections that will give the best
video quality. For example, choose HDMI over component video, and choose component video over S-video
or composite video.
IMPORTANT
Accessory items such as cables, adapters,
splitters, or combiners required for TV
connections are not supplied with the TV.
These items are available at many electronics
stores.
Picture Quality
Usually, to receive the best picture quality, connect the
source device video directly to the TV input without
routing it through other devices.
Cable Management
One cable tie with a locking pin is supplied with the accessories. Use the tie to keep cables properly organized and
connected.
Cable Routing
Cable tie
Installing the Cable Tie
1. Remove the locking pin from the cable tie and
2.
insert the anchor prongs into the hole on the back
of the TV.
Reinsert the pin in the cable tie to secure the tie to
the TV.
Cable tie
Cable routing on
back of TV
1.
Pin
2.
Hole in
back of TV
Lift tab to
release
Unlatching the Cable Tie
Back of TV
Downloaded From TV-Manual.com Manuals
Pry up the latch tab and push or pull
the free end of the tie through the latch.
Lift the latch tab by pinching the tab
and latch body between your thumb
and index finger. Otherwise, use a
plastic wallet card or similar object to
pry up the tab.
23
3. TV Connections
HDMI Device (Cable Box, Satellite Receiver, DVD Player, or Other Device)
Required: HDMI-to-HDMI cable.
ANT-2/AUX
ANT-1/MAIN
TV main
panel
VIDEO
Pr
INPUT 2
L - AUDIO - R
INPUT 3
Pb
R
R
DVI/PC INPUT
L - AUDIO - R
L
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
AVR AUDIO
OUTPUT
L
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
R
Mitsubishi recommends you use category 2 (high-speed)
HDMI cables to connect HDMI 1.3 source devices.
High-speed category 2 cables bring you the full benefits
of Deep Color and x.v.Color. See “HDMI Cable Categories,” page 13, for more on HDMI cable types.
Y
INPUT 1
Y/VIDEO
Connect an HDMI cable from the TV main panel to the
HDMI device output. HDMI devices provide video and
audio through the single cable.
3D GLASSES EMITTER
VIDEO: 480i/480p/720p/1080i/1080p
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p, 1080p
Any HDMI
device
R
L
AUDIO
Figure 1. Connecting an HDMI device.
Note: HDMI inputs are
certified for proper
interoperability with other products certified by
Simplay™.
Component Video Device (HDTV Cable Box or Satellite
Receiver, DVD Player, or Other Device)
AVR AUDIO
OUTPUT IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
L
R
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
TV
main
panel
1.
2.
3D GLASSES EMITTER
Downloaded From TV-Manual.com Manuals
2.
RS-232C
Figure 2. Connecting a device with
component video outputs
R
DVI/PC INPUT
L - AUDIO - R
R
R
To hear digital surround sound, connect the digital
audio output from the device directly to your digital
A/V receiver.
L - AUDIO - R
L
Note:
INPUT 3
INPUT 2
Pr
the cable from the outside cable or satellite service
to CABLE IN or SATELLITE IN on the cable box or
satellite receiver. See your device’s owner’s guide
for instructions and cable compatibility.
1.
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
VIDEO
Pb
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
3. Cable Box or Satellite Receiver Only: Connect
Y/VIDEO
ANT-2/AUX
ANT-1/MAIN
Y
Y/VIDEO
INPUT 1
Required: RCA component video cables, left/right
analog stereo audio cables.
1. Connect RCA-type cables from the Y Pb Pr outputs
on the device to the Y Pb Pr inputs on the TV main
panel, matching the colored green, blue, and red
connections.
2. Connect left (white) and right (red) audio cables
from the device to AUDIO L and R on the TV main
panel.
INPUT 1
If your cable box or satellite receiver has an HDMI
output, use the connections for HDMI devices
described on this page.
L
R
AUDIO
3.
Incoming from
cable service or
satellite dish
Y
Pb
CABLE IN or
SATELLITE IN
Pr
24
3. TV Connections
DVI Video Device (Cable Box, Satellite
Receiver, DVD Player, or Other Device)
Connect DVI devices (digital only) to the TV’s HDMI
input jacks.
Analog stereo audio cables and a DVI-to-HDMI cable or
DVI/HDMI adapter and HDMI cable are required.
1. Connect the DVI-to-HDMI cable (recommended) or
HDMI cable with DVI/HDMI adapter from the DVI
device’s back panel to the TV’s HDMI jack.
Note:
If you are using a DVI/HDMI adapter, it is important to connect the adapter to the DVI device for
best performance.
S-Video Device (Standard Cable Box,
Satellite Receiver, or Other Device)
Required: S-Video cable and left/right analog stereo
audio cables.
1. Connect an S-Video cable from S-VIDEO OUT on
the cable box or satellite receiver back panel to
INPUT 3 S-VIDEO on the TV main panel.
2. Connect left (white) and right (red) audio cables
from AUDIO OUT on the cable box or satellite
receiver to INPUT 3 AUDIO L and R on the TV main
panel.
3. Connect the cable from the outside cable or satellite service to CABLE IN or SATELLITE IN on the
cable box or satellite receiver.
2. Connect a set of audio cables from AUDIO OUT
on the DVI device back panel to the DVI/PC INPUT
AUDIO on the TV main panel. Connect the red
cable to the R jack and the white cable to the L
jack.
Note:
Note: Refer to the cable box or satellite receiver
Owner’s Guide for cable or dish antenna connections to the receiver.
The HDMI connection supports copy protection
(HDCP).
L- AUDIO - R
INPUT 3
ANT-2/AUX
ANT-1/MAIN
Any S-Video
device
2.
L-- AUDIO - R
INPUT 3
Connect audio
cables to INPUT
3 AUDIO
R
AUDIO
DVI/PC INPUT
L - AUDIO - R
R
R
1.
AVR AUDIO
OUTPUT
L
R
S-VIDEO
(INPUT 3)
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
1.
S-VIDEO
OUT
3D GLASSES EMITTER
INPUT 2
Pr
L - AUDIO - R
INPUT 3
Pb
R
R
DVI/PC INPUT
L - AUDIO - R
L
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p, 1080p
TV main
panel
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
DVI/PC INPUT
L - AUDIO - R
AVR AUDIO
OUTPUT
L
R
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
Incoming
cable from
wall
3.
CABLE IN or
SATELLITE IN
Figure 4. Connecting a device with S-Video
AUDIO: PCM STEREO
3D GLASSES EMITTER
VIDEO: 480i/480p/720p/1080i/1080p
2.
1.
Figure 3. Connecting a digital DVI device
Downloaded From TV-Manual.com Manuals
L
VIDEO
INPUT 2
L
VIDEO
1.
Pr
ANT-2/AUX
ANT-1/MAIN
Y
INPUT 1
Y/VIDEO
2.
Pb
DVI OUT
Pr
Pb
L
YPbPr(480i/480p/720p/1080i)
AUDIO
R
L
Y
Digital DVI device
INPUT 1
TV main
panel
Y/VIDEO
Some devices require connection to an analog input
first in order to view on-screen menus and to select DVI
as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.
2.
25
3. TV Connections
Wall Outlet Cable (no cable box)
Antennas with Separate UHF and
VHF Leads
You should connect the incoming cable for your primary
viewing source to ANT 1/MAIN.
Required: UHF/VHF combiner, coaxial extender
1. Connect the primary incoming coaxial lead cable to
1. Connect the UHF and VHF antenna leads to the
UHF/VHF combiner.
ANT 1 on the TV main panel.
2. For an optional secondary antenna source, connect
ANT-2/AUX
ANT-1/MAIN
ANT-2/AUX
ANT-1/MAIN
VHF antenna
(channels 2–13)
VIDEO
Y
INPUT 2
Pr
L - AUDIO - R
INPUT 3
Pb
TV main panel
Flat twin lead
R
AVR AUDIO
OUTPUT
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
3D GLASSES EMITTER
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p, 1080p
ANT-2/AUX
ANT-1/MAIN
VIDEO
INPUT 3
L - AUDIO - R
DVI/PC INPUT
L - AUDIO - R
L
R
AVR AUDIO
OUTPUT
L
R
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
RS-232C
3D GLASSES EMITTER
VIDEO: 480i/480p/720p/1080i/1080p
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p, 1080p
Figure 7. Connecting a single antenna lead
Pr
Coaxial
extender
INPUT 2
ANT-1/MAIN
Optional 300-ohm-to
75-ohm matching
transformer
A2.
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
A1.
R
B.
Pb
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
300-ohm
flat twin
lead
Y
INPUT 1
75-ohm
coaxial
lead
Connect the coaxial lead directly to ANT 1 on the
TV main panel.
Downloaded From TV-Manual.com Manuals
L
R
TV main panel
Y/VIDEO
B. For cable or antenna with coaxial lead
DVI/PC INPUT
L - AUDIO - R
L
Figure 6. Connecting separate UHF and VHF antennas
Mitsubishi strongly recommends you avoid using
antennas with flat twin leads. Flat twin lead
antenna wires are subject to interference which
may adversely affect the performance of the TV.
We recommend using coaxial antenna cable.
Required: 300-ohm-to-75-ohm transformer, coaxial
extender.
A1. For an antenna with flat twin leads, connect the
300-ohm twin leads to the 300-ohm-to-75-ohm
transformer.
A2. Connect the transformer to an extender and
push the extender onto ANT 1 on the TV main
panel.
INPUT 3
Pr
ohm combiner
Figure 5. Wall Outlet Cable
A. For an antenna with flat twin leads
INPUT 2
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
3D GLASSES EMITTER
2.
1. 300-ohm-to75-
Coaxial
extender
Antenna with a Single Lead
L - AUDIO - R
Pb
R
ANT-1/MAIN
VHF
VIDEO
Y
EXTERNAL
CONTROLLER
INPUT
Back Side
view view
UHF
TV main panel
Y/VIDEO
R
External antenna
or cable
Pr
Pb
L
YPbPr(480i/480p/720p/1080i)
DIGITAL
AUDIO OUTPUT
L
R
AVR AUDIO
OUTPUT IR NetCommand
OUTPUT/
R
INPUT 1
DVI/PC INPUT
L - AUDIO - R
L
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
To ANT 2
UHF antenna
(channels 14–69)
ANT-2/AUX
ANT-1/MAIN
INPUT 1
Y/VIDEO
To ANT 1
2. Connect the combiner to an extender and push the
extender onto ANT 1 on the TV main panel.
an antenna (or cable) to ANT 2.
26
3. TV Connections
VCR to a Cable Box (Audio & Video)
VCR to an Antenna or
Wall Outlet Cable
Required: Two-way RF splitter, two coaxial cables, right
and left analog audio cables, either S-video or composite video cable.
1. Connect the incoming cable or antenna to IN on the
RF splitter.
2. Connect one coaxial cable from OUT on the RF
3.
4.
4.
Incoming
cable
TV main
panel
L - AUDIO - R
DVI/PC INPUT
L - AUDIO - R
L
R
2.
Cable
box
7.
IN
5.
6.
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
S-VIDEO
(INPUT 3)
AVR AUDIO
OUTPUT
L
R
OUT
Audio and
video from
cable box
to TV
4.
7.
3D GLASSES EMITTER
VIDEO
VIDEO
Y
Y/VIDEO
INPUT 1
L
R
R
DVI/PC INPUT
L - AUDIO - R
L - AUDIO - R
INPUT 3
Pr
INPUT 2
L - AUDIO - R
INPUT 3
Pb
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
VIDEO: 480i/480p/720p/1080i/1080p
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p, 1080p
ANT-1/MAIN
ANT-2/AUX
ANT-1/MAIN
4.
6.
INPUT 3
L - AUDIO - R
INPUT 3
Pr
INPUT 2
3.
3.
3.
3.
VIDEO
VIDEO
Pb
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
1.
Y
R
2.
2.
1.
ANT-2/AUX
ANT-1/MAIN
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
TV main
panel
3.
Y/VIDEO
Incoming
cable
splitter to CABLE IN on the cable box.
Connect one coaxial cable from OUT on the RF
splitter to ANT 1 on the TV main panel.
Connect one coaxial cable from OUT on the cable
box to ANTENNA IN on the VCR back panel.
ANT-1/MAIN
5.
1. Connect the incoming cable to IN on the RF splitter.
2. Connect one coaxial cable from OUT on the RF
INPUT 1
splitter to ANTENNA IN on the VCR back panel.
Connect one coaxial cable from OUT on the RF
splitter to ANT 1 on the TV main panel.
Connect either an S-Video or composite video
cable from VIDEO OUT on the VCR back panel to a
VIDEO composite or S-VIDEO jack on the TV main
panel. Connect only one type of video cable;
S-Video is recommended, if available.
To use the TV speakers with the VCR, connect left
(white) and right (red) audio cables from AUDIO OUT
on the VCR to the associated AUDIO L and R jacks
on the TV main panel. If your VCR is mono (nonstereo), connect only the white (left) cable.
Required: Two-way RF splitter, three coaxial cables,
right and left audio cables, S-Video or composite video
cable, plus video and audio cables required to connect
the TV to the cable box.
6.
6.
4.
5.
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
S-VIDEO
(INPUT 3)
AVR AUDIO
OUTPUT
L
R
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
4.
VCR
S-VIDEO
OUT
L
R
AUDIO OUT
VIDEO
OUT
ANTENNA
IN
5.
AUDIO: PCM STEREO
3D GLASSES EMITTER
VIDEO: 480i/480p/720p/1080i/1080p
Figure 9. Connecting a VCR to a cable box
2.
4.
VCR
S-VIDEO
OUT
5. Connect the cable box outputs to the TV as shown
4.
L
R
AUDIO OUT
VIDEO
OUT
ANTENNA
IN
6.
Figure 8. Connecting a VCR to allow recording from an
antenna source.
Downloaded From TV-Manual.com Manuals
in one of the options listed below. This connection
allows the TV to receive the best available signal
directly from the cable box.
• Figure 1, page 23: HDMI output to the TV’s
HDMI jack.
• Figure 2, page 23: Component video output
to the TV’s Y Pb Pr jacks; analog stereo audio to
the associated AUDIO jacks.
Connect either an S-Video or composite video
cable from VIDEO OUT on the VCR back panel
to a VIDEO composite or S-VIDEO jack on the TV
main panel. Connect only one type of video cable.
27
3. TV Connections
7.
S-Video is preferable to composite video, if available.
To use the TV speakers with the VCR, connect left
(white) and right (red) audio cables from AUDIO OUT
on the VCR back panel to the associated INPUT
AUDIO L and R on the TV main panel. If your VCR
is mono (non-stereo), connect only the white (left)
cable.
Note: When using this connection configuration with the
connections used in step 5, it is possible to view
live cable programs through the VCR Device. For
best picture quality always view live cable programs
directly from the TV input connected to the cable
box device.
Audio-Only Device
If you wish to connect an audio-only device to the TV, such
as an audio CD player or an MP3 player, follow these instructions.
1. Insert an unused RCA-style connector into the
2.
3.
4.
Y/VIDEO jack. The presence of this connector activates the TV’s Auto Input Sensing feature.
When the Auto Input Sensing screen displays,
name the new input CD/Audio or MP3 Player.
Connect left (white) and right (red) audio cables from
AUDIO OUT on the device to AUDIO L and R on the TV.
Keep the connector in the Y/VIDEO jack while using
the audio-only device.
Audio-only device
2.
L
R
Y/
VIDEO
Older Cable Box
1.
Required: One coaxial cable.
Note: This connection is not recommended. The
other connections described in this chapter
provide better quality audio and video to the TV
and allow NetCommand to work with the cable
box.
USB
INPUT 4
L
R
Y/
VIDEO
Pb
1. Connect the incoming cable to IN on cable box.
2. Connect one coaxial cable from OUT on the cable
TV INPUT 4
convenience
panel
Pr
TV back
box to ANT 1 on the TV main panel.
ANT-2/AUX
ANT-1/MAIN
Figure 11. First insert an unused RCA-type connector
into the Y/VIDEO jack on the TV side or main panel
before connecting audio cables.
2.
INPUT 3
INPUT 2
Pr
L - AUDIO - R
Pb
R
R
DVI/PC INPUT
L - AUDIO - R
L
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
ANT-1/MAIN
VIDEO
Y
Y/VIDEO
INPUT 1
AVR AUDIO
OUTPUT
L
R
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
2.
Cable
box
OUT
RS-232C
3D GLASSES EMITTER
VIDEO: 480i/480p/720p/1080i/1080p
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p, 1080p
IN
TV main
panel
1.
Incoming
cable
Figure 10. Connecting an older cable box
Downloaded From TV-Manual.com Manuals
28
3. TV Connections
A/V Receiver (Sound System) Using the
TV’s Audio Output
Most setups require either a digital audio cable or analog
stereo audio cables. To send audio from TV channels
received on ANT 1, ANT 2, or devices connected directly to
the TV, you must use one of the connections shown below.
The TV makes all audio available in digital and analog formats:
• Analog audio coming into the TV is output in digital
stereo format on the DIGITAL AUDIO OUTPUT jack.
• Digital incoming audio is output on the analog AVR
AUDIO OUTPUT L and R jacks.
• The TV’s digital audio output sends Dolby Digital signals
only when you are viewing TV channels received on ANT
1 or ANT 2. Audio from all other devices connected
directly to the TV will be output as PCM stereo. To send
Dolby Digital or other digital surround from these devices
to the AV Receiver, connect the digital audio output of
the device directly to the A/V receiver.
Usually, only one of the following audio connections is required.
• To connect an analog A/V receiver
Connect left (white) and right (red) audio cables from
AVR AUDIO OUTPUT L and R on the TV main panel to
the TV AUDIO INPUT on the A/V receiver.
• To connect a digital A/V receiver with Dolby
Digital surround sound and PCM audio support:
Connect one end of the digital audio cable to DIGITAL
AUDIO OUTPUT on the TV main panel. Connect the
other end to the COAXIAL DIGITAL INPUT on the back of
the A/V receiver.
•
hear such copy-protected signals through the A/V
receiver, use the connection for an analog A/V receiver.
Check the A/V receiver’s Owner’s Guide for information
concerning use of the digital input and switching between
digital sound and analog stereo sound from the TV.
A/V Receiver with HDMI Output
Required: One HDMI-to-HDMI cable
This option allows you to view content from devices connected to an A/V receiver. The A/V receiver can send audio
and video to the TV over a single HDMI cable. You can use
an HDMI connection as described here in addition to an
audio connection from the TV’s audio output.
You may be able to use the TV’s remote control (with slide
switch set to TV) to operate connected CEC-enabled HDMI
devices. Experiment with your equipment to determine
which functions are available to the TV’s remote control. See
Appendix D, “NetCommand HDMI Control of CEC Devices”
on page 78.
This setup allows you to use NetCommand-controlled
audio and video switching over the HDMI cable. See “A/V
Receiver Control: Automatic Audio and Video Switching via
HDMI” on page 64.
VCR
Cable box
DVD player
High-definition
DVD player
TV main
panel
ANT-2/AUX
ANT-1/MAIN
ANT-2/AUX
ANT-1/MAIN
VIDEO
Y
Y/VIDEO
INPUT 1
AUDIO DIGITAL HDMI
AUDIO IN OUT
IN
VIDEO
AVR AUDIO
OUTPUT
L
R
DVI/PC INPUT
L
DIGITAL
AUDIO OUTPUT
L - AUDIO - R
INPUT 3
INPUT 2
L
AVR AUDIO
OUTPUT
R
DIGITAL
AUDIO OUTPUT (INPUT 3)
Downloaded From TV-Manual.com Manuals
L
AUDIO: PCM STEREO
RS-232C
3D GLASSES EMITTER
DIGITAL
AUDIO OUTPUT
VIDEO: 480i/480p/720p/1080i/1080p
Note:
• On rare occasions, an HDMI signal may be copy-restricted
and cannot be output from the TV as a digital signal. To
Pr
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
Figure 12. Connecting the TV to an A/V receiver
Pb
AVR AUDIO
OUTPUT
L
R
TV
main
panel
Digital coaxial cable
(for connecting a
digital A/V receiver)
Pr
Pb
L
YPbPr(480i/480p/720p/1080i)
R
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
COAXIAL
INPUT
Y
DVI/PC INPUT
L - AUDIO - R
L
R
OPTICAL
INPUT
Y/VIDEO
INPUT 1
L - AUDIO - R
Pr
INPUT 2
AVR AUDIO
OUTPUT
L
R
INPUT 3
Pb
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
Stereo analog cables
(for connecting an
analog A/V receiver)
A/V receiver
back panel
A/V receiver with
HDMI output
Optional
recommended
analog or digital
audio connection
HDMI
cable
Figure 13. An A/V receiver connected to the TV with an
HDMI cable may offer special control capabilities.
To hear sound from the antenna inputs (ANT 1, ANT 2) or
devices connected to the TV only, use the optional audio
connection to send audio from the devices through the
TV to the A/V receiver.
29
3. TV Connections
Camcorder
The TV’s INPUT 4 convenience inputs
offer the easiest way to connect a camcorder. You can alternatively use jacks
on the main connection panel. Two different connection options are described
on this page.
2.
A: Composite video
plus audio
L
R
Y/
VIDEO
1.
USB
Use jacks on the TV‘s INPUT 4
panel to connect a camcorder.
TV convenience
input panel
(INPUT 4)
INPUT 4
L
R
A: Composite Video Connection
Y/
VIDEO
Pb
Required: Composite video and analog stereo audio
cables supplied with the camcorder.
1. Connect the composite video cable from VIDEO
OUT on the camcorder to the TV’s Y/VIDEO convenience jack.
2. Connect left (white) and right (red) audio cables
from AUDIO OUT on the camcorder to the TV’s
AUDIO L and R convenience jacks.
Pr
2.
B: Component
video plus
audio
L
R
Y/
VIDEO
Pb
B: Y Pb Pr Component Video Connection
Required: Component video and analog stereo audio
cables supplied with the camcorder.
3. Connect component video cables from VIDEO OUT
on the camcorder to the TV’s Y Pb Pr component
convenience jacks.
4. Connect left (white) and right (red) audio cables
from AUDIO OUT on the camcorder to AUDIO L and
R on the TV.
Downloaded From TV-Manual.com Manuals
1.
Pr
TV INPUT 4
Figure 14. Two connection options for a camcorder.
30
4
TV Operation and Features
Choosing a Viewing Source
Sleep Timer
The Sleep Timer turns the TV off after the length of time
you set. To set the TV to turn on at a certain time, see
the Setup > Timer menu on page 49.
Setting the Sleep Timer
1. Press SLEEP on the remote control.
Input Selection menu
2. Press SLEEP additional times to increase the time in
Choose a viewing source from the Input Selection
menu. The current TV input appears as a full-color icon
in this menu.
1. Press INPUT to display the Input Selection menu. If
there are only two inputs to the TV, INPUT switches
between them without displaying the menu.
2. Highlight an input icon using
.
3. Press ENTER to switch to the input and close the
menu.
3.
4.
Cancelling the Sleep Timer
1. Press SLEEP to display the on-screen message.
2. Press SLEEP repeatedly until OFF is displayed.
More About the Input Selection Menu
• To assign meaningful names to the icons, see the
Inputs > Name menu, 51.
• To rearrange the icons, see the Inputs > Order
menu, 51.
Note:
TV Tips
Turning the TV On or Off
To turn the TV on or off, point the remote control at the
front of the TV and press the POWER key. Alternatively,
press the POWER button on the TV’s control panel.
•
•
Controlling Sound Volume
•
•
•
•
Press VOL
/
to adjust the sound level.
See also “Controlling A/V Receiver Sound Volume” on
page 18.
Changing Channels (antenna sources)
To change channels:
• Enter the channel number using the number keys
on the remote control and press ENTER. For a two-
Downloaded From TV-Manual.com Manuals
30-minute increments up to the maximum of 120
minutes.
Press EXIT or wait five seconds without pressing any
keys for the message to disappear.
Press SLEEP to view the time remaining before the
sleep timer turns off the TV.
•
After five seconds of inactivity, the message box
will disappear.
—
part digital channel, such as 3-1, press 3 CANCEL 1
to enter a dash (separator).
Press CH/PAGE
/
to change channels one
channel at a time.
Press and hold CH/PAGE
/
to move quickly
through channels.
Press QV (QuickView) to switch back to the previously tuned channel.
Press GUIDE to display ChannelView channel listings,
highlight a channel, and press ENTER.
Use the Fav (Favorites) feature to set up lists of
favorite channels and tune to them with the FAV key.
See Setup > Edit > Fav1–Fav6 on page 47.
NOTE: Perform channel memorization (a channel scan)
to make finding channels easier. See Setup >
Scan, page 46.
31
4. TV Operation and Features
Remote Control
1.
POWER: Turns TV power on and off.
2. Slide Switch: Selects the A/V device to be operated by the remote control. Set the slide switch to TV
for operation of the TV, and NetCommand-controlled
devices. Control of additional devices requires programing (see Appendix C, “Programming the Remote
Control.”
3. SLEEP: Sets the TV to turn off within 2 hours in increments of 30 minutes.
4. Digits/Letters: Press digits for channel numbers,
then press ENTER for faster tuning. Use numbers and
—
the CANCEL key to enter digital sub-channel numbers.
Use also for entering letters or names in menus.
To select letters when naming channels, repeatedly
press the associated number key. Press ENTER to set
the letter. Special characters are available with the 1
key (!, &, blank space) and 0 key (/, *, -).
5. —/CANCEL (SUB-CHANNEL/CANCEL): When entering digital
channel numbers, adds a separator between main
and sub-channel numbers. Clears Fav and some
menu entries.
6. QV (QuickView™): Switches between the current
channel and the last channel viewed.
7. MUTE: Turns TV sound on and off.
8. SPLIT: Not used in this model.
9. FAV (Favorites): Scans through memorized lists of
favorite channels. See Setup > Edit > Fav1–Fav6
on page 47.
10. VOL
/
(Volume Up/Down): Changes sound level.
11. CH/PAGE
/
(Channel or Page Up/Down): Scans
up or down through memorized channels. Pages
up and down through screens when used with
ChannelView.
12. FORMAT: Changes the shape and size of the TV picture.
13. LIST: Works like the LIST key for a cable box or satellite
receiver when “learned” for NetCommand or when the
remote has been programmed for the device.
14. INPUT: Displays the Input Selection menu from which
you can select an input source to view, such as an
antenna input (ANT 1/2) or a connected device.
15.
(Adjust Up/Down/Left/Right): Navigate
menus and change settings.
16. ENTER: Selects a channel number or menu item.
17. GUIDE: Displays or removes ChannelView™ channel
listings for ANT 1 and ANT 2. Displays DVD disc or
top menu for a NetCommand-controlled DVD player.
Displays the guide for a NetCommand-controlled
cable box or satellite receiver.
18. INFO: Displays an on-screen summary of the current
device in use and any broadcast information avail-
Downloaded From TV-Manual.com Manuals
2
3
1
4
5
6
7
8
10
11
9
12
13
14
15
16
19
17
18
24 25 26
20
21
22
27 28 29
23
able, including current V-Chip ratings information.
See “Status Display” on page 33 for details.
19. AUDIO: Selects individual audio settings to adjust.
See page 44 for a description of audio settings.
20. VIDEO: Selects individual video settings to adjust.
See page 42 for a description of video settings.
21. MENU: Displays the main TV menu. When a submenu is open, backs up one menu level.
22. EXIT: Closes TV on-screen menus/displays.
23. F1–F4
For devices under NetCommand control:
Perform NetCommand “Learning” to assign your
choice of functions to the F1–F4 keys.
32
4. TV Operation and Features
Remote Control, continued
For devices operating independently of
NetCommand: The F1–F4 keys work like the A,
B, C, D buttons on some cable boxes, satellite
receivers, and DVD players. Program the remote
control for your equipment and test the keys. See
Appendix C, “Programming the Remote Control.”
25.
(PAUSE): Freezes a broadcast TV picture from an
antenna source, cable box, or satellite receiver (if
key has not been reassigned for NetCommand use).
Care of the Remote Control
•
•
•
•
•
•
•
Record/Playback Keys
Use any of these methods to enable the recording and
playback commands of the TV’s remote control:
• Program the remote control for your DVR, VCR, or
DVD player/recorder and set the slide switch to VCR,
DVD, CABLE/SAT, or AUDIO as appropriate.
• Check HDMI devices for compatibility with the TV’s
NetCommand for HDMI feature (see Appendix D).
• Perform NetCommand IR “learning” for the device.
24.
(RECORD): Records with a VCR or DVR.
25.
(PAUSE): Pauses a VCR, DVR, or DVD. See
above for use during TV viewing.
26.
(STOP): Stops play of a VCR, DVR, or DVD.
27.
28.
29.
(REVERSE): Rewinds a VCR. Reverse scans a
DVR or DVD.
(PLAY): Plays a VCR, DVR, or DVD.
(FORWARD): Fast forwards a VCR. Forward scans
a DVR or DVD.
Note: To operate other audio/video devices using
the TV’s remote control:
• See Appendix C, “Programming the Remote
Control.”
• For HDMI devices compatible with the TV’s NetCommand for HDMI feature, see Appendix D.
• See chapter 6, “NetCommand IR Control,” for
NetCommand IR “Learning” of device keys.
• For use of specific keys with NetCommand-controlled devices, see “Special Operation Methods,”
page 59.
Resetting the Remote Control
If the slide switch is set to TV and the TV does not
respond properly, reset the remote control.
1. Press and hold POWER for several seconds until the
key blinks twice and goes off.
2. Release the POWER key.
3. Press keys 0 0 9 3 5 and the POWER key will blink
twice when you finish entering the code. While
entering the code, pause for a moment between
each key press to ensure it is recognized.
Downloaded From TV-Manual.com Manuals
Use only alkaline batteries.
Be within 20 feet of the equipment.
Do not press two or more keys at the same time
unless instructed to do so.
Do not allow unit to get wet or become heated.
Avoid dropping on hard surfaces.
Do not use harsh chemicals to clean. Use only a soft,
lightly moistened cloth.
Do not mix old and new batteries.
Low-Battery Indicator
If you press a key and the POWER key blinks five times,
replace the remote control’s batteries.
ChannelView Channel Listings
ChannelView™ displays channel names and program information, as sent by broadcasters or your local cable service
provider, for memorized channels on ANT 1 or ANT 2. Listings
may be incomplete. No program information is displayed for
analog channels. An analog channel name is displayed only if
you assigned a name in the Setup > Edit menu (page 47).
To receive ChannelView updates:
• Keep the Energy Mode set to Fast Power On
• Set the TV clock
• Leave the TV powered off for a while each day to
receive updates.
Notes:
- Listings are updated for the digital channel you are
currently watching.
- If the time or date displayed are incorrect, change the
TV’s time, time zone, date, or Daylight Savings Time
settings in the Setup menu.
Using ChannelView
Feature
Press Key
See ChannelView listings Press GUIDE.
from ANT 1 or ANT 2.
Close ChannelView
Press GUIDE or EXIT.
Scan channels one by one. Press and hold
or
Scan channels quickly.
Press and hold PAGE
Jump to listings for a
specific channel.
1.
.
/
.
Enter the channel
number (see numbers in
upper left of screen).
2. Press ENTER.
See more of the program Press INFO.
description (if available).
Move navigation to the
program listings.
Press .
Move navigation to the
channel listings.
Press .
Tune to the highlighted
channel.
Press ENTER.
33
4. TV Operation and Features
Status Display
Ant 1
Press the INFO key to see the
on-screen status display.
The most common displays
are shown here. You will
rarely, if ever, see all status
indicators at the same time.
2
3
7-1 KABC-HD 4 Monday Night Football
10
HD 16:9 Standard
TV-PG
9
Stereo
11
6
7
FAV1
English 12
13
Tuesday 9:10 PM
Sleep 30 min
5
On-screen status display
sample information
1
15 MUTE
St. Louis vs. Tampa Bay
8
8
14
Signal Strength 16
Analog Sources
Digital Sources
1.
Source antenna or input
Source antenna or input
2.
Analog channel being received (antenna sources only)
Digital major and sub-channel numbers (antenna
sources only)
3.
Analog channel name (if named in the Setup > Edit
menu); antenna sources only.
Digital Channel Name (if broadcast or if named in the
Setup menu > Edit options; antenna sources only)
4.
(Does not apply)
Program name (if broadcast)
5.
Signal Type Being Received
Signal Type Being Received.
6.
Screen Format in use
Screen Format in use
7.
Current Fav bank number of channel (antenna
sources only)
Current Fav bank number of channel (antenna
sources only)
8.
(Does not apply)
Program description if broadcast (antenna sources
only)
9.
V-Chip rating (antenna sources or VIDEO composite
and S-VIDEO jacks only)
V-Chip rating (antenna sources only)
10.
Audio Source. Possible:
Audio Source. Possible:
TV speakers,
external sound system
TV speakers,
external sound system
11.
Listen To indicator. Possible: Stereo, Mono, SAP
(antenna sources only)
Listen To indicator. Possible: Stereo, Surround, Dual
Mono
12.
(Does not apply)
Current available language (antenna sources only)
13.
Day and time
Day and time
14.
Sleep Timer remaining time
Sleep Timer remaining time
15.
Mute indicator
Mute indicator
16.
(Does not apply)
Signal strength indicator (antenna sources only)
Downloaded From TV-Manual.com Manuals
34
4. TV Operation and Features
Fav (Favorite Channels)
Use the six Fav channel banks to store groups of your
favorite channels from ANT 1 and ANT 2. You can set
up a Fav channel bank for each of your favorite program
types or set up a bank for each TV user.
You may prefer to perform Fav channel setup from a
menu. See the Setup > Edit options, page 47.
ANT-1
480i Stretch
TV-PG
Stereo SAP
4
FAV2
FAV
Channel and Fav numbers in the
on-screen status display
Using Fav Channels
See the current Fav bank number
Press INFO.
View channels in current Fav bank
1. Press the FAV key. Wait for the TV to tune to a channel in the current Fav bank.
2. Press the FAV key repeatedly to cycle through the channels available in the
current Fav bank.
Change Fav banks
1. Press the FAV key. Wait for the TV to tune to a channel in the current Fav bank.
2. When tuning is complete and while the TV status display is still visible on
screen, press the number key for the desired bank (1–6).
Note: Wait for the channel change to finish before pressing the number key.
Otherwise, the TV may ignore the Fav number.
If no Fav banks are set up
The FAV key switches to the previously tuned channel; works like the QV key.
Fav Setup Using Only the Remote Control
Add Fav channels
1. While watching TV, tune to the channel you want to add to the current
Fav memory bank. The default bank is Fav1. See the instructions above
if you need to change to a different Fav bank.
2. Press and hold the FAV key for about 2 seconds. When FAV and the
memory bank number appear under the channel number, the channel
has been successfully added.
Remove Fav channels
This procedure removes the channel
only from the selected bank and
leaves the other banks unchanged.
1. While watching TV, press the FAV key.
Downloaded From TV-Manual.com Manuals
2. While the TV status display is still visible on screen, press the number
key for the memory bank.
3. Press the FAV key repeatedly until you see the desired channel in the onscreen status display.
4. While the channel number and FAV indicator (with correct bank number)
are still displayed on the screen, press CANCEL. You must press CANCEL
while the indicator is displayed. When the FAV indicator disappears
after pressing CANCEL, the channel has been successfully removed.
35
4. TV Operation and Features
TV Signals and Display Formats
This is a 16:9 widescreen TV suitable for images available from HDTV and many DVDs. You can view olderstyle squarish images (4:3 aspect ratio) using one of the
display formats described on this page. Press the FORMAT
key to cycle through the available display formats. The TV
remembers the format you last used for each input.
Original
Signal
TV
Display
Non-Anamorphic (or 4:3, 1:33:1, Letter Box, or
Full Screen)
Indicates DVDs recorded for viewing on squarish TV
screens. They may be full screen (4:3 or 1:33:1) which
crops movies to fit the narrow TV, or letter box, which
adds black top and bottom bars.
Distorted. Not
recommended.
Recommended
Expand
Recommended
for letterbox.
See Note 1.
Distorted; not
recommended.
See Note 1.
Zoom
Distorted. Not
recommended.
See Note 1.
Recommended
for anamorphic
2.35:1 images.
See Note 1.
Stretch
Recommended
for standard
broadcasts.
See Note 1.
Distorted; not
recommended.
See Note 1.
Stretch
Plus
Recommended
for standard
broadcasts.
See Note 1.
Distorted; not
recommended.
See Note 1.
Narrow
See Note 1
Distorted; not
recommended.
See Note 1.
Signal Definitions
480i: Traditional interlaced signals from ANT-1 and ANT 2,
composite VIDEO, component Y Pb Pr, and HDMI jacks.
480p: Progressive-scan DVD signals on component Y Pb
Pr and HDMI jacks.
720p and 1080i: High-definition signals received through
component Y Pb Pr and HDMI jacks. These signals are
always 16:9 (widescreen).
SD 4:3: Standard-definition squarish-screen-format
signals from digital channels on ANT 1 and ANT 2.
SD 16:9: Standard-definition widescreen-format signals
from digital channels on ANT 1 and ANT 2.
HD 16:9: High-definition 16:9 widescreen signals from
digital channels on ANT 1 and ANT 2.
TV Display Format Definitions
Standard: This is the full-screen format used by HDTV
signals. Use this format to display anamorphic DVDs with a
1.78:1 or 1.85:1 aspect ratio. Anamorphic DVDs with a 2.35:1
aspect ratio are displayed correctly but with top and bottom
black bars. Narrow (4:3) images are stretched evenly from
side to side. Available for all signals.
Expand: Enlarges the picture to fill the screen by cropping
the top and bottom; useful for reducing the letter box top and
bottom bars of non-anamorphic DVD images.
Zoom: Enlarges the picture to fill the screen by cropping the
sides, top, and bottom to eliminate black bars. 480i/480p
and SD 4:3 signals: Eliminates top and bottom bars on anamorphic DVDs with a 2.35:1 aspect ratio. 720p, 1080i, SD
16:9, and HD signals: Eliminates bars added to 4:3 images.
Downloaded From TV-Manual.com Manuals
Anamorphic DVD
Standard
DVD Image Definitions
Image information may be stated on the DVD case. Some
DVDs support both of the formats described below.
Anamorphic (or Enhanced for WideScreen TV)
Indicates DVDs recorded to show widescreen images properly on 16:9 TV sets using the TV’s Standard format mode
(recommended).
Non-anamorphic or
SD 4:3
Original Signal
SD 16:9 or
HD Digital
720p,
1080i,
1080p
Signal
Display Formats
Standard
Use for widescreen images.
Wide Recommended to reExpand move side bars.
Zoom
Recommended to remove bars from the top,
bottom, and sides.
TV Display Formats. Press the FORMAT key repeatedly to
see the displays available for the current program. Press
the INFO key to see the name of the display format in use.
Note 1: Available for 480i, 480p, and digital SD 4:3 signals only.
Stretch: Stretches a narrow 4:3 image across the screen
to display the entire image with less distortion than the
Standard format.
Stretch Plus: Similar to Stretch, but minimizes distortion on
the sides by expanding the picture to crop off portions of the
top and bottom. You can adjust the vertical position of the
picture. Press VIDEO repeatedly to show the Vert Adjustment
option, then press ENTER. Use
to move the picture.
Narrow: Displays narrow 4:3 images in their original shape.
Adds black side bars to fill the screen.
Wide Expand: Enlarges the picture, cropping the image on both
sides. Removes or reduces black side bars added to narrow
images converted to 16:9 signals for digital broadcast.
Note: All high-definition channels send widescreen (16:9)
signals, but not all programming was created for this format. The
broadcaster may stretch the image or add side bars to fill the
widescreen area.
36
4. TV Operation and Features
Viewing Camera Files
JPEG Thumbnail Menu
Use these keys while viewing JPEG thumbnail images.
JPEG Photos and the USB Photo Port
Keys for the JPEG Thumbnail Menu
1. Back up the data on
2.
Move the highlight from image to image.
your USB drive before
connecting it to the
TV. Mitsubishi is not
USB
responsible for file
damage or data loss.
INPUT 4
Connect your USB card
Optional
reader or USB drive to
audio
the TV’s USB Photo
device
port.
TV convenience
The USB Photo menu
input panel
displays while files are
(INPUT 4)
being read. Wait until
you see the completion
message on screen before continuing.
FORMAT
Rotate the thumbnail clockwise in 90˚ increments.
or
ENTER
Play the slide show starting with the highlighted thumbnail.
Highlight the last thumbnail on the current page.
L
Highlight the first thumbnail on the current page.
R
Note:
Some manufacturers’ devices may be incompatible with the TV. If the TV is unable to display your
photos, you can:
CH/PAGE /
Display the next or previous page of thumbnails.
EXIT
Close the Thumbnail menu and display the
USB Photo menu.
MENU
Close the Thumbnail menu and display the
Main menu.
INPUT
Close the Thumbnail menu and display the
Input Selection menu.
•
•
3.
Transfer files to a different USB device.
Use the camera’s composite video output
as described later in this chapter.
Refer to the table below for use of the USB Photo
menu after files have been read.
4. Optional: Connect an audio device to the INPUT
4 AUDIO L and R stereo jacks to play sound while
viewing pictures.
USB Photo Menu Options
Start slide show.
With the Slideshow icon highlighted, press
or ENTER.
Activate menu options. Highlight an icon and press
ENTER to:
• start the slide show
• display picture thumbnails
• open the Media Setup
submenu.
Display or close the
Main menu.
Press MENU.
Display status for the
file source.
Press INFO.
Select a different con- 1. Press INPUT.
nected device
2. Highlight the icon for a different device.
3. Press ENTER.
Clear status display
or menu to show the
USB Photo menu
JPEG Thumbnail Menu
Press EXIT.
Downloaded From TV-Manual.com Manuals
Notes on Viewing JPEG Files
• The TV ignores all commands while reading files. Wait
for the completion message before continuing.
• Large files or high-capacity storage devices may take a
long time to display. The screen will be blank while files
are read.
• Use only one source device at a time.
•
Back up the data on your USB drive before connecting it to the TV. Mitsubishi is not responsible
for file damage or data loss.
IMPORTANT
Stop playback or change to a different TV input
before disconnecting from the USB photo port.
37
4. TV Operation and Features
Slide Show
USB Photo Menu Compatible Picture Files
Use these keys during the slide show.
•
Still images recorded on digital cameras using the
Exchangeable Image File Format, version 2.1 (EXIF
2.1) standard for digital still cameras and Design
Rules for Camera File Systems version 1.0 (DCF 1.0)
Some images opened and resaved on a computer
may not play back or may not display in the thumbnail list. This happens if the files were resaved in an
incompatible format.
Full path file names can be no longer than 50 characters and must end in a .jpg extension. Only the
first 20 of the 50 characters will display.
Images on storage devices with a capacity of over
256 MB can take a longer initial time to display.
The storage device must use the FAT/FAT32 files
system.
Keys for JPEG Picture Slide Show
Begin or resume slide show playback
Pause or resume playback while in automatic advance mode.
or
ENTER
Advance to the next slide.
•
Go to the previous slide.
FORMAT
Rotate the slide clockwise in 90˚ increments.
•
Stop slide show and display the USB Photo
menu.
•
INFO
Display status for the viewing device and
current image.
INPUT
Display the Input Selection menu.
MENU
Display or remove the TV Main menu.
Note:
•
Always press (STOP) to stop slide show playback before disconnecting from the USB Photo
port.
Media Setup Menu
Camera Photos and Moving Video as
Composite Video
Connect the camera to the TV using a composite video
cable if:
• You are unable to see images using the USB photo
port.
• You wish to view moving video from the camera.
The TV’s USB Photo menu will be unavailable and you
must control the slide show through the camera. Display
resolution is standard-definition (480i).
1. Refer to the owner’s manual supplied with the
2.
Media Setup menu
In the Media Setup menu you can adjust the slide show
display, number of repetitions, or display interval.
• Select either Auto or Manual advance. During
manual operation, press
or ENTER to advance to
the next slide.
• For automatic advance, select the time interval for
display of each slide. The interval you select here is
the minimum time between slides; actual time may
be longer for larger files.
• For automatic advance, select the number of times
(frequency) to play the complete slide show: Once,
Twice, or Continuous.
• Press EXIT to close the Media Setup menu and
return to the USB Photo menu.
IMPORTANT
The TV can read JPEG photo files as created by
the camera. If you edit a photo file on a computer
and resave the image, the TV may be unable to
read the resaved file.
Downloaded From TV-Manual.com Manuals
3.
4.
5.
6.
7.
camera for instructions needed for this setup.
Set the camera’s output signal type to NTSC and put
the camera into playback mode.
With the camera still turned on, connect your digital
camera’s composite video cable (usually yellow) to
the VIDEO/Y jack on the TV. To hear audio, connect
the camera’s audio output cable to the AUDIO L jack.
When the Auto Input Sensing screen displays,
press EXIT or assign the name Camcorder.
Press INPUT to display the Input Selection menu.
Highlight the icon
for the camera
Optional
input and press
Audio Cable
ENTER.
If viewing photos,
L
advance through
R
the images
manually or set
Y/
the camera to
VIDEO
advance autoPb
matically.
Pr
Camera connection
using a composite
video cable
38
4. TV Operation and Features
3D Video
This section provides Instructions for viewing 3D video
using the TV’s 3D feature. The 3D options are found in
the Setup > 3D menu described on page 50 .
Initial Set-Up
1. Check if your HDMI 3D video source device outputs
2.
a 1080p 60-Hz signal. This information will be
needed when you assign an input name in the Auto
Input Sensing screen.
If your 3D glasses came with an emitter box,
connect the emitter box to the 3D GLASSES
EMITTER jack on the back of the TV. See page 12
for the location of the jack.
3. Power on the TV and the source device.
4. Connect the source device to the TV’s HDMI input.
5. When the Auto Input Sensing screen displays,
name the input according to the table below.
The signal type and choice of name are important
because the TV will process the video signal
differently depending on the name you assign. If
your 3D source is a computer, name the input
PC. If your source device is a high-definition disc
system such as Blu-ray, or is a game console, the
signal must be 1080p at 60-Hz.
6. Press EXIT to close the Auto Input Sensing screen.
Name to Assign to
Video Input
Source of 3D Video
Type of 3D Video Signal
Computer
Recommended: 1080p 60 Hz (1920 X 1080). The image will fill
the TV screen.
Other 60-Hz computer video signals compatible with the TV will
display with black bars. See “Computer Display Formats” on
page 21.
PC
Any other 3D video
source
To see 3D video, signal must be 1080p, 60-Hz
Any name other than
PC
To Watch 3D Video
1. Press INPUT to display the Input Selection menu.
2. Highlight the icon for the 3D video input and press
ENTER.
Press MENU and select the Setup > 3D Mode menu.
3.
4. Set 3D Mode to On. The On setting will be memorized for the current input when you exit this menu.
5. Press EXIT to close the menu.
6. To see the best effect, you may need to synchronize
your 3D glasses with the image. Display the Setup
> 3D Mode menu and under Glasses L–R, select
either Standard or Reverse.
To Watch Regular (non-3D) Video
The 3D Mode setting is memorized for each input.
When you want to watch non-3D video on the input
selected above:
1. Select the input in the Input Selection menu.
2. Open the Setup > 3D menu and set 3D Mode to
Off.
Downloaded From TV-Manual.com Manuals
Use the Setup >
3D Mode menu to
enable 3D video
viewing.
39
TV Menus
5
Main Menu
Press MENU on the remote control to open the Main menu.
Icon
Menu Name and Description
AV Menu
Page
Customize picture and sound settings.
Turn closed captions on and off; customize
Captions Menu caption displays.
40
45
Setup Menu
Perform basic TV setup. Set language, scan
(memorize) channels, set the TV clock, edit
channel options, lock TV use by channel, set
Energy Mode, set the auto-on TV Timer, set 3D
options.
46
Inputs Menu
Assign names to TV inputs, change icon order in
the Input Selection menu, perform NetCommand
IR “learning,” enable/disable NetCommand HDMI
control.
51
Lock Menu
Restrict TV use by program ratings and by time of
day. Disable the control-panel touch keys. Set a
pass code.
52
Main menu
Remote Control Keys for the TV Menu System
5
6
Key
Function
1
MENU
Display or close the Main menu or move back one menu level.
2
EXIT
Close all menus and return to TV viewing.
(Adjust Left/Right Keys)
•
•
•
3
(Adjust Up/Down Keys)
4
ENTER
Start an automatic function or check/uncheck a check box. When
setting time, move from hour digits to minutes digits and from
month to day to year digits.
5
Numbers
Letters
Enter channel numbers.
Enter custom names in some text boxes.
6
CANCEL
•
•
7
INFO
Get context-sensitive help.
3
4
7
Move through screens to select menu options.
Change settings.
Scroll through lists.
1
2
Downloaded From TV-Manual.com Manuals
Clear a setting or stop an automatic function.
Add a separator in a digital channel number.
40
5. TV Menus
AV Menu
An on-screen slider displays when making some audio
and video adjustments. Numeric values represented on
the slider range from 0 (minimum) to 63 (maximum), with
31 as the mid-point.
The AV menu contains sub-menus for audio and video
adjustments
AV Menu Options
Video
See the description of video adjustments on page 42.
Audio
See the description of audio adjustments on page 44.
•
Reset
PerfectColor
•
To reset audio and video adjustments for the current input, highlight the Reset icon and
press ENTER.
Reset has no effect on settings for Balance, Listen To, Language, and Film Mode.
PerfectColor Sliders
Sliders adjust the saturation (intensity) of six colors for the
current image source.
PerfectTint Sliders
Sliders adjust six hues for the current image source
To use PerfectColor and PerfecTint:
Highlight the PerfectColor™ icon and press ENTER to display the PerfectColor menu. Settings
are retained in memory independently for each TV input.
• To switch between PerfectColor™ and PerfecTint™ adjustments, highlight Adjust Mode
and press
.
• Press
to move from one color bar to the next.
• Press
to change settings.
• Press CANCEL to restore default settings.
• Press MENU to return to the Main menu.
PerfectColor sliders let you adjust the saturation of six colors.
Downloaded From TV-Manual.com Manuals
PerfecTint sliders let you adjust six hues.
5. TV Menus
41
AV Menu, continued
AV > Global menu
AV Menu Options
Video Mute
On, Off
•
Global
•
Audio Only
Screensaver
On, Off
•
•
On: Displays a solid blue background when there is
no video signal from the current input.
Use the On setting to let the colored screen remind
you that the TV is powered on at times when there is
no picture. The TV will power off after five minutes if it
detects no video signal.
Off. The screen appears black if there is no video
signal from the current non-antenna input.
On: Select On to display a random screensaver
pattern while playing an audio-only device. The
device must be named CD/Audio or MP3 Player to
use this feature.
Off: No screensaver pattern displays during play of
an audio-only device.
Note:
When playing an audio-only device, the TV will
power off after 12 hours of inactivity.
Film Mode
(480i and 1080i
signals only)
Auto, Off
In Auto, the TV automatically detects and applies filmdecoding correction to movies filmed at 24 frames per
second. Try the Off setting if images show many jagged
edges.
Smooth 120 Hz
Off, On
When On, Smooth 120Hz™ reduces motion blur in action
scenes but may show pixel structure during slower motion or in
still images. When Off, standard picture smoothing processing
is employed.
Blue Glow
On if TV off,
On if TV on,
Off
Select one of the On settings to see decorative blue lighting on the TV.
Displays a 1080i (high-definition) test picture for use during troubleshooting
under the direction of TV servicing personnel.
Test Picture
Downloaded From TV-Manual.com Manuals
42
5. TV Menus
Video Menu
Mitsubishi recommends you assign names to TV inputs
before making video adjustments (use the Inputs >
Name menu). Otherwise, adjustments will be reset to the
defaults if you name inputs afterwards.
To make video adjustments:
• From the Video menu:
1. Press
to highlight an option.
2. Press
to display the submenu and adjust.
3. Press MENU to return to the AV menu.
• While watching TV: Press the VIDEO key repeatedly to display the video option you want to change.
Press
to change settings.
AV menu, Video options
Video Menu Options
Picture Mode
Brilliant
For use under bright light; unavailable when the
current input is named Game or PC.
Game
Optimizes picture and video processing for gaming
consoles. Available only when the name of the
input is Game or PC.
Bright
For most daytime viewing and x.v.Color sources
Natural
For most nighttime viewing and x.v.Color sources
Set the Picture Mode first
before changing other video
settings, as some settings are
stored independently for each
Picture Mode. Use Picture
Modes to get the best image
under different viewing conditions.
Contrast
•
•
•
•
•
Adjusts the white-to-black level
Settings are stored independently for each Picture Mode.
Low contrast shows a variety of shades in darker images
In most home lighting situations, medium contrast looks best.
High contrast shows darker images more uniformly black and makes colors appear more
vibrant. High contrast is good for brightly lit environments.
Brightness
•
•
Adjusts overall picture brightness
Settings are stored independently for each Picture Mode.
Color
Adjusts overall color intensity from no color to fully saturated.
Tint
Adjusts the red-to-green ratio.
Sharpness
Adjusts picture detail and clarity.
Color Temp
Adjusts the white balance. Settings are stored independently for each Picture Mode.
Video Noise
High
Gives white images a cool cast. May provide the most realistic picture under bright lighting.
Low
Gives white images a warm cast. Natural/Color Temp at the low setting displays
video at approximately the 6500K industry standard for NTSC pictures.
High,
Medium,
Low, Off
Reduces minor noise (graininess) in the picture. Use Low with good-quality signals. Use
High with poor-quality signals. Use Off to leave the picture unaltered. Saved by input.
Downloaded From TV-Manual.com Manuals
5. TV Menus
43
Video Menu, continued
Video Menu Options
SharpEdge
On, Off
SharpEdge™ adds special edge enhancements to make the image appear
sharper. Saved by input.
Deep Field
Imager
On
DeepField™ Imager dynamically enhances black levels in portions of the screen
to provide strong contrast with detail over mixed screen content.
Off
Contrast is adjusted uniformly across the entire screen.
Demo
For comparison, displays a split picture to show On (right side) and Off (left side).
Vert Adjustment
(Stretch Plus
Format mode only)
•
•
Press the ENTER key to enter adjustment mode (in Stretch Plus format only).
Press
to move the picture up or down.
Horiz position
(Computer
image only)
Press
to display the adjustment slider. Press
or
to shift the image horizontally.
Vert position
(Computer
image only)
Press
to display the adjustment slider. Press
or
to shift the image vertically.
Downloaded From TV-Manual.com Manuals
44
5. TV Menus
Audio Menu
To make audio adjustments:
• From the Audio menu:
to highlight an option
1. Press
2. Press
to display the submenu and adjust.
3. Press MENU to return to the AV menu.
• While watching TV: Press the AUDIO key repeatedly
to display the audio option you want to change.
Press
to change settings.
AV menu, Audio options
Audio Menu Options
Speakers
The Speakers option displays only if an A/V receiver connection has been detected.
Note: NetCommand-controlled A/V receiver switching operates only when this option is set to
AV Receiver and there is an A/V receiver connected to the TV’s AVR AUDIO OUTPUT or DIGITAL
AUDIO OUTPUT.
TV
Turns on the internal TV speakers.
AV Receiver
Turns off the TV speakers so you hear sound only from a connected A/V receiver.
Note: When you disconnect an analog A/V receiver, be sure to manually
change the Speakers setting to TV to hear sound from the TV speakers.
Bass
Controls volume of low-pitched sound from the TV speakers.
Treble
Controls volume of high-pitched sound from the TV speakers.
Balance
Controls audio balance between the right and left TV speakers
Sound Mode
Normal
No special audio effects from the TV speakers (default)
Expand
Modifies audio from the TV speakers.
• For monaural (non-stereo) programs, creates a simulated stereo effect.
• For stereo programs, creates a simulated surround sound effect.
Stereo
Default setting. The TV plays stereo broadcasts in stereo and mono broadcasts
in mono. The word Stereo is displayed when you tune to a channel broadcasting in stereo.
Mono
Reduces background noise. Use when receiving a weak stereo audio signal. All
audio is played as mono with this setting.
SAP
(Second
Audio
Program)
Selects an additional monaural sound track not audible during normal TV viewing.
The SAP signal might be related to the program (such as a sound track in a
foreign language), or it might be unrelated (such as a weather report). If an SAP
signal is broadcast, the letters SAP are displayed when you tune to the channel
Listen To
Available for
analog channels from
ANT1/ANT2
only
Language
Available for
digital channels from
ANT1/ANT2
only.
Level Sound
English, French,
German, Italian,
Portuguese,
Spanish, Other
On, Off
Downloaded From TV-Manual.com Manuals
Selects the current language for a digital program from ANT1 or ANT2. Each
digital program may include zero to seven language choices.
Reduces differences in sound volume between programming segments, such as
the difference between regular broadcast programs and commercial segments.
5. TV Menus
45
Captions Menu
Captions on Digital Channels
Captions on Analog Channels
The TV can decode captions from ANT 1/ANT 2 and the
VIDEO composite and S-VIDEO jacks. Broadcasters can
send either standard closed captions or text service. Standard closed captions follow the dialogue of the program and
display in a small section of the screen. Text-service closed
captions often contain information such as weather or
news and cover a large portion of the screen.
•
•
•
IMPORTANT
Analog text-service options display a large
black or gray box on the screen when no signal
is being broadcast.
The content of captions is determined by the
broadcaster. If captions show strange characters, misspellings, or odd grammar, it is not a
malfunction of the TV.
Closed caption signals are not available through
HDMI or component jacks. See the menus for
these devices for closed-caption decoding.
The TV can decode captions from ANT 1/ANT 2 only.
Broadcasters can send up to six different captioning
selections or can send analog captions that match those
sent by the analog station. A TV station may broadcast
only one or two types of captions or none at all.
Digital Settings menu. Check the caption test area
(upper right) to see how custom settings look.
Captions Menu Options
Analog
Captions
On if Mute
CC 1–CC 4
Text 1–Text 4
Off
•
Analog
Background
Gray, Black
Selects either a gray or black text background to make analog
closed captions easier to read.
Digital
Captions
On if Mute
Caption 1–
Caption 6
Off
•
Font
Default
Font 1–Font 7
Default changes settings to those selected by the captions provider, or, if none, to the TV’s own captions defaults. Use Fonts 1
through 7 to give captions a custom appearance.
Font Size
Large
Standard
Small
Large is the recommended size.
Font Color
White, Black, Magenta, etc.
Font Opacity
Translucent, Opaque, Flashing,
Transparent
Background
Color
White, Black, Magenta, etc.
Background
Opacity
Translucent, Opaque, Flashing,
Transparent
Closed
Captions
Digital
Settings
Downloaded From TV-Manual.com Manuals
•
•
•
On if Mute: Displays analog closed captions signal CC 1
when audio from the TV speakers is muted. When watching
TV, press MUTE to turn captions on/off.
CC 1–CC 4: Standard closed-caption signals
Text 1–Text 4: Text-service signals
On if Mute: Displays digital closed caption signal Caption 1
when audio from the TV speakers is muted. When watching
TV, press MUTE to turn closed captions on/off.
Caption 1–Caption 6: Caption signals sent by the broadcaster
Guidelines for setting digital captions:
• A white font on a black translucent
background makes an easy-to-read
combination.
• Use contrasting colors for captions and
background.
• Check readability of captions using the
sample text in the upper right corner of
the menu.
46
5. TV Menus
Setup Menu
Use the Setup menu to:
• Select English or Spanish for menus and on-screen
text.
•
•
•
•
•
•
Scan the channels available for the antenna or cable
service connected to the ANT 1 or ANT 2 jacks.
Edit channel options, including channel locking.
Set the TV’s internal clock.
Set the TV Timer to turn on the TV automatically at
a designated time.
Set the energy mode for power consumption when
the TV is powered off.
Control 3D mode.
Setup menu, Scan option
Setup Menu Options
English
Spanish
Display on-screen menus in either English or Spanish.
Ant-1 Air
Ant-1 Cable
Ant-2 Air
Ant-2 Cable
Scan memorizes broadcast channels to make them easier to find. To start
channel memorization:
1. Highlight one of the input selections based on your connection to ANT 1
or ANT 2:
• Air when connected to an indoor or outdoor antenna.
• Cable when connected to direct cable (no cable box)
2. Press to highlight START.
3. Press ENTER to start channel memorization for the selected input.
Language
Scan
Note: To listen to audio in other languages (when available), see the section
on the AV menu, Audio submenu, and refer to either Listen To > SAP (analog
signal) or Language (digital signal).
Notes on Scan and channel memorization:
• Channel memorization may take up to 15 minutes
to complete.
• To stop channel memorization before completion,
press CANCEL.
• When watching TV, press CH
to move through
memorized channels.
• To add a digital channel that does not appear in the
Edit menu without repeating channel memorization:
1. Look up the physical channel number for the new
digital channel. The website www.antennaweb.org
can help you find the physical channel number.
2. Tune to any channel on the ANT 1 or ANT 2 input
your antenna is connected to.
Downloaded From TV-Manual.com Manuals
3. Use the number keys and CANCEL key to enter the
physical channel number followed by “-1” and ENTER.
For example, for physical channel 36, press
—
3 6 CANCEL 1 ENTER.
The TV will search for a digital channel on the channel
36 frequency. When it finds the channel, it will:
•
a. Add the channel to memory.
b. Change the channel number to the virtual
channel number sent by the broadcaster.
c. Add to memory any associated sub-channels.
Rememorize channels if you move the TV to a
different geographic area with a different channel
line-up.
5. TV Menus
47
Setup Menu, continued
Edit
Virtual Channel Number (digital channels only). A channel
number sent by a local broadcaster. Usually the virtual
number is associated with the corresponding analog
channel number. For example, a broadcaster may associate digital channel 2-1 with their analog channel 2.
Physical Digital Channel Number. The channel number
officially assigned to the actual broadcast frequency; shown
on screen in parentheses.
Setup menu, Edit channel options
Setup Menu Options
Edit
Use the Edit menu to edit channel options when ANT 1 or ANT 2 is the current source,
To highlight a channel number to edit:
• Press CH
/
to jump to the next page of channel numbers. Press and hold CH
/
to speed
through pages.
• Press
to move through all channel numbers, one at a time. Press and hold
to speed
through channel numbers.
The TV tunes to the highlighted channel on release of CH
/
or
.
Channel
Channels marked with a check are in memory. To add or delete a channel from
memory, highlight the channel number and press ENTER. To add a single digital channel
not in the list, see the notes under Scan on the opposite page.
Digital channels are listed by virtual channel number with the physical channel number
shown in parentheses.
Name
Assign a custom name up to six characters long to memorized channels. You can
name analog channels and digital channels if broadcast without pre-assigned names.
1. With the cursor in the Name field, press a number key repeatedly to cycle through
the characters associated with the key, including !, &, blank (1 key) and /, *, - (0
key).
2. Press ENTER to set the letter and move to the next letter position. To delete the
current character and move back one position, press CANCEL.
Fav1– Fav6
Use the six Fav channel banks to store groups of your favorite channels. For example,
you can set up a Fav channel bank for each of your favorite program types (e.g., sports,
news, children’s programs) or set up a bank for each TV user.
• Use
to move the highlight through the Fav area of the screen.
• Press ENTER to insert a check mark to add the highlighted channel to one of the Fav
banks.
• The same channel can be added to multiple Fav banks
• To remove a channel from a Fav bank, highlight the check mark and press ENTER.
Note: To set up Fav channel banks without using this menu, see “Fav (Favorite Channels)” on page 34.
Lock
Lock channels so that a pass code is required to view them. When you rememorize
channels, all lock settings are cleared.
Highlight the Lock column and enter a pass code when prompted. If you previously
set a pass code to open the main Lock menu, use the same pass code. See “Lock
Menu,” page 52 for more on pass codes.
To lock or unlock a channel, highlight the lock icon for the channel and press ENTER to
switch between the locked and unlocked versions of the icon.
Downloaded From TV-Manual.com Manuals
48
5. TV Menus
Setup Menu, continued
Clock
Set the clock if you wish to:
• Use the TV’s Timer function.
• Maintain accurate ChannelView listings.
Use either the manual or auto method to set the clock.
Setup menu, Timer and Clock options
Setup Menu Options
Settings
Timer
Clock
Manual. To set the clock manually:
1. Select Manual.
2. Set the time of day.
3. Set the date.
4. Select your time zone.
5. Select either Applies or Ignore for Daylight Savings Time.
Note: If using Manual, each time the time change occurs, you must open this
menu and set the TV’s clock ahead or back.
Auto. To set the clock automatically:
1. Select Auto.
2. Select your time zone.
3. Select either Applies or Ignore for Daylight Savings Time.
4. After exiting the menus, tune the TV to an analog station on ANT 1 or ANT 2
carrying XDS data, typically a PBS station.
Note:
• With the Auto setting and Applies selected for Daylight Savings Time, the TV’s
clock adjusts automatically to daylight savings time.
• The TV’s clock will be reset if you tune to a channel sending incorrect time data.
To prevent unwanted clock resets, first use the Auto method to set the clock
from a channel sending the correct time, then change the method to Manual.
Time
(Manual
option only)
1. With the hour highlighted, press
repeatedly to change the hour and the
AM/PM indicator. Press and hold to change the hour display quickly.
2. Press ENTER to set the hour.
3. With the minutes highlighted, press
to change the minutes. Press and
hold to change the minutes display quickly.
Date
(Manual
option only)
1. With the month highlighted, press
2. With the day highlighted, press
3. With the year highlighted, press
Time Zone
Eastern, Central,
Mountain,
Pacific, etc.
Required for both the Manual and Auto methods.
Daylight
Savings
Time
Applies
Ignore
Required for both the Manual and Auto methods. Select
the option for your area.
Downloaded From TV-Manual.com Manuals
to select. Press ENTER to set.
to select. Press ENTER to set.
to select the current year.
5. TV Menus
49
Setup Menu, continued
Timer
Use the Timer to set a time for the TV to turn on automatically. Use this menu to set a day, time, input, and
channel for the Timer. If the TV is already on at the
requested time, the TV will automatically tune to the
designated channel.
•
•
•
•
•
The TV clock must be set before you can use the
Timer feature.
TV Energy Mode must be set to Fast Power On to
have the TV power on at the set time.
To open the Timer menu, highlight the Timer icon
in the Setup > Timer Clock menu and press ENTER.
The POWER indicator on the front of the TV flashes
slowly when the TV is off to indicate the TV Timer
has been set.
When the Timer turns on the TV, press any key on
the remote control to keep it on. Otherwise, the TV
will turn off after five minutes.
Setup menu, Timer options
Setup Menu Options
Timer
On, Off
Day
Daily, Mon-Fri, (every) Sunday, (every) Monday, (every) Tuesday, etc.
Select the day or days of the week for the Timer to turn on the TV.
Time
To set the time for the TV to come on:
1. With the hour highlighted, press
repeatedly to change the hour and the AM/
PM indicator. Press and hold to change the hour display quickly.
2. Press ENTER to highlight the minutes.
3. Press
to change the minutes. Press and hold to change the minutes display quickly.
Input
Ant-1, Ant-2, DVD, VCR, etc.
Select the input you want displayed when the TV comes on. Choose from the defined
and enabled inputs that appear in the Input Selection menu.
Channel
If the input is an antenna (ANT 1, ANT 2), enter a channel number in any of three ways:
• Enter the number using the remote control’s number keys.
• Press
repeatedly
• Press and hold
to scroll quickly through the available channel numbers.
Timer
Downloaded From TV-Manual.com Manuals
50
5. TV Menus
Setup Menu, continued
Setup menu, 3D options
Setup Menu Options
Energy
Mode
Energy
Fast Power On
Low Power
Use the Energy Mode option to select the level of power consumption while the TV is turned off.
The default setting is Fast Power On.
Low Power uses less energy, but TV power-on takes longer and
some TV features may be unavailable.
Keep Energy Mode set to Fast Power On if you need to:
• Have faster power on.
• Receive updates to ChannelView channel listings.
• Use the External Controller Input Wired IR option (see page 13).
3D Mode
3D
Mode
On, Off
Glasses
L-R
Standard,
Reverse
Use the On setting for video games and movies that require 3-D glasses.
See a description of using 3D Mode in “3D Video,” page 38.
Synchronizes the 3D glasses with the image on screen to provide the
best 3D effect. Standard is the default; try Reverse if this seems
incorrect.
Note: 3D options are recommended only for 1080p 60 Hz video sources connected to an HDMI input.
Downloaded From TV-Manual.com Manuals
5. TV Menus
51
Inputs Menu
Inputs Menu Options
Name
Cable Box, Camcorder, CD/
Audio, DVD (DVD, DVD2,
Blu-Ray), DVR, Game (Game,
PS, Xbox, Wii), MP3 Player, PC,
Satellite, VCR, AVR
On/Off (ANT 1 and ANT 2 only)
Delete (deactivated HDMI only)
Control On, Control Off (CECenabled HDMI devices; operates
only when Inputs > NetCommand
HDMI Control is set to On)
•
•
•
•
Lets you assign or change names of inputs appearing in
the Input Selection menu.
- Press
to move between inputs.
- Press
to select a name.
Lets you turn Ant-1 and Ant-2 On/Off (to display/hide in Input
Selection menu).
Lets you delete unused HDMI inputs from the Input Selection
menu.
If you change the name of an input after performing NetCommand “learning,” the IR codes you “learned” are
erased.
General Notes
When you change an input name in the Name menu and then exit the Name menu:
• The name is changed
• The icon in the Input Selection menu is changed
• Audio and video settings are changed to the defaults for the new device type.
• All previous NetCommand “learning” for the input is erased.
Notes for HDMI devices
• Disconnecting an HDMI device: When you disconnect an HDMI device, the icon remains in the Input Selection menu until you remove it. Select Delete in the Inputs > Name menu to remove an unwanted icon for an HDMI
input.
• NetCommand for HDMI and CEC-Enabled Devices: If CEC conflicts occur, turn off CEC signals in one
of these ways: a) Turn off all NetCommand for HDMI signals from the TV (Inputs > NetCommand HDMI
Control menu), b) Turn off NetCommand HDMI signals for specific devices (Inputs > Name menu), or c) Turn
off each device’s internal CEC capability. See Appendix D for the TV’s NetCommand for HDMI Control or, to
turn on/off a specific device’s response to CEC signals, see the device’s owner’s manual.
• Names of CEC-enabled devices: CEC-enabled devices send their own predefined name to the TV. You
cannot change the name of a CEC-enabled device; applies only when Inputs > NetCommand HDMI Control
is set to On.
Order
Lets you put frequently used icons at the start of the Input Selection menu.
to highlight the icon to move.
1. Press
2. Press ENTER to confirm the selection.
3. Press
to drag the icon to the desired position.
4. Press ENTER to set the new position.
Learn
Sets up or changes NetCommand IR control of the current viewing device.
See detailed instructions in chapter 6, “NetCommand IR Control.”
AV Receiver
Sets up NetCommand IR control of an A/V receiver.
See detailed instructions in chapter 6, “NetCommand IR Control,” starting on page 61.
On, Off
NetCommand
HDMI Control
Downloaded From TV-Manual.com Manuals
Select On or Off to enable or disable the TV’s control of CEC-enabled
devices. See Appendix D for details.
52
5. TV Menus
Lock Menu
TV locks available from the Lock menu are:
Parent
Lock by Ratings
Restricts access to programming
based on V-Chip rating signals sent
by the broadcaster.
Other
Time
Control
Panel
Note:
Lock by Time
Restricts TV use by time of day.
Lock Control Panel
Disables the touch keys on the TV’s
control panel. Use this option if
small children in the home try to
press control-panel touch keys.
Channel Lock is an additional lock that blocks
access to specific channels. Channel Lock is
available under the Setup menu (Setup > Edit
> Lock, page 47).
Pass Codes
Setting the Pass Code
You are prompted to enter a pass code whenever you
select Lock on the Main menu. To set a pass code for
the first time:
1.
Press MENU, highlight Lock, then press . A screen
prompting you for a pass code will display.
2. Input a four-digit pass code using the number keys
on the remote control.
• Press CANCEL to delete a number and move back
one space.
• Press MENU or EXIT to close the menu without
setting a pass code.
3. Press ENTER to set the pass code.
The Lock > Parent menu lets you set parental controls
using V-Chip technology.
Parent Menu
The TV comes from the factory with the rating locks
turned off and with pre-set U.S. ratings TV-PG and
movie rating PG. Turn on blocking for U.S. ratings
to activate these rating restrictions. Use the Lock >
Parent menu to change the level of blocking with U.S.
ratings.
Any time you change the channel or device, it may take
up to five seconds for the rating restrictions to take
effect.
Other Menu (Alternate Rating System)
This TV can recognize new rating systems that may
come into effect in the future. The Other menu allows
you to block digital programming when such systems
come into effect.
The first time you tune to a channel broadcasting an
alternate rating system, the TV defaults to the most
restrictive setting if the Lock menu > Other Lock
option is set to On. Use this menu to change the
allowed rating if you are unable to watch a program
broadcast with an alternate system.
Resetting the Pass Code
See the procedure in Appendix B.
Bypassing TV Locks
•
•
•
•
Important Notes on Rating Locks
Parent menu rating locks apply only to channels
and signals received on ANT 1, ANT 2, and the
VIDEO composite and S-VIDEO jacks.
Other menu rating locks apply only to digital channels received on ANT 1 or ANT 2.
When viewing a cable box, satellite receiver, or
other device connected to the component Y Pb
Pr or HDMI inputs, check the device’s owner’s
guide for use of parental locks.
Downloaded From TV-Manual.com Manuals
•
If you try to watch a blocked program or channel,
or the TV is locked by time, a notice will appear
prompting you for a pass code. To use the TV,
input your four-digit pass code and press ENTER.
- To reactivate the locks after using a pass code,
power the TV off and then on.
- To reactivate only the parent ratings lock,
change to a different channel or device.
If a program or channel is blocked, you can still
use the TV without entering a pass code. The lock
allows you to change to a channel airing an allowed
program or change to another device.
53
5. TV Menus
Lock Menu, continued
Parent Menu Options (U.S.-based rating system)
Option Name and Description
Lock
Off, On
Disables or enables program blocking based on V-Chip signals and the U.S. rating system.
TV
Rating
TV-Y
Youth. For children under 7.
TV-Y7
Youth 7 and older.
TV-G
General Audience. For the entire family.
TV-PG
Parental Guidance. Parental Guidance recommended; may
not be suitable for some children.
TV-14
Adolescent 14 and older. Not recommended for children under 14.
TV-MA
Mature Audience. For adults only.
Highlight the rating level
you wish to change and
press ENTER to block it
( ) or allow it ( ).
You can apply supplemental content blocking
to the age-based ratings
by using the TV content
categories listed below.
FV
Fantasy Violence. Applies to TV-Y7 only.
D
Sexual Dialog. Applies in differing degrees to TV-PG and TV-14.
L
Adult Language. Applies in differing degrees to TV-PG, TV-14, and TV-MA.
S
Sexual Situations. Applies in differing degrees to TV-PG, TV-14, and TV-MA.
V
Violence (graphic or realistic). Applies in differing degrees to TV-PG,
TV-14, and TV-MA.
Movie
Rating
G
General Audience. Designed for the entire family to view.
PG
Parental Guidance. Parental Guidance is recommended, may not be suitable for some children.
PG-13
Parental Guidance, 13 and Older. Not recommended for children under the age of 13.
R
Restricted. Restricted in theaters to 17 years old and older unless accompanied by an adult.
NC-17
No Children 17 or Under. Restricted in theaters to 18 years old and older.
X
Adult. Designed for and restricted in theaters to adult audiences only.
Not Rated
Start
Time
Stop
Time
TV Content
Categories
No MPAA rating assigned.
Allows you to set the time of day for enforcement of rating restrictions set in the Parent menu.
1. Highlight the hour digits for Start Time.
2. Press
repeatedly to change the hour and associated AM/PM indicator. You can also just press
and hold to move quickly through the numbers.
3. Press ENTER to highlight the minutes.
4. With the minutes digits highlighted, press
repeatedly to change the minutes. You can also just
press and hold to move quickly through the numbers.
5. Highlight the Stop Time digits and set the time as described above.
Note:
To make rating restrictions active 24 hours a day, make Start Time and Stop Time the same.
Downloaded From TV-Manual.com Manuals
54
5. TV Menus
Lock Menu, continued
Other Menu Options (alternate rating system)
This TV can recognize new rating systems that may come into effect in the future. The Other option remains grayed
out until the TV receives a signal using an alternate rating system. Such alternate rating systems will apply only to
digital programming received on the ANT 1 and ANT 2 inputs.
Option Name and Description
Lock
On, Off
Enable or disable program blocking.
System Name
The rating system available for the channel
Group
Rating groups available in the rating system shown on the screen. Rating groups are defined by
the rating system in effect.
Rating
Rating restrictions available in the selected rating system and group. Highlight the rating and
press ENTER to check (block) or uncheck (allow) rated content.
Time
Blocks all use of the TV during the time period you specify. You must enter a pass code to use the TV when the time
lock is in effect.
Lock by Time
On, Off
Lock Time,
Unlock Time
To set the lock and unlock times:
1. Highlight the hour digits for the Lock Time.
2. Press
repeatedly to change the hour and associated AM/PM indicator. To move quickly
through the numbers, just press and hold.
3. Press ENTER to set the hour and highlight the minutes.
4. With the minutes highlighted, press
repeatedly to change the minutes. To move quickly
through the numbers, just press and hold.
5. Highlight the Unlock Time digits and set the time as described above.
Note:
Enable or disable Lock by Time.
To make Lock by Time active 24 hours a day, make Start Time and Stop Time the same.
Control Panel
On, Off
On locks and Off unlocks the touch keys on the TV’s control panel. Use this option if small children may try to press TV touch keys.
• If the remote control is unavailable, use the TV’s control panel to release the Control Panel
Lock. Press and hold the MENU touch key for over eight seconds.
• If the TV is powered off, release the lock as described above. The TV will power on.
• To reactivate the lock, you must return to this menu and change the setting to On.
Downloaded From TV-Manual.com Manuals
6
NetCommand IR Control
About NetCommand IR Control
Note:
•
•
•
•
•
To learn about NetCommand for HDMI devices,
see Appendix D and “About Home-Theater
Control Systems,” page 19.
NetCommand setup is optional.
You may wish to use NetCommand IR control to
supplement CEC control.
You can perform NetCommand setup when the TV
first recognizes a device during Auto Input Sensing
or at any convenient time afterward.
NetCommand operates by sending remote control
signals from the TV to your other devices via the IR
emitters, telling the devices to play, record, change
inputs, adjust volume, change channels, or perform
other functions. All this is accomplished with the
TV’s remote control and the slide switch left in the
TV position.
The IR “Learning” feature of NetCommand allows
the TV to learn the IR control signals for your A/V
devices.
Important Note on NetCommand
Be sure to connect the IR emitter cable to the
TV and properly place the emitters so that
NetCommand can control your devices. See
the explanation on the next page.
Downloaded From TV-Manual.com Manuals
•
You can choose the level of NetCommand control
for your home theater.
Standard Setup. Perform a standard setup if
you want NetCommand to control only a few
devices, such as the TV, a playback device (like
a DVD player), and a cable box. With this setup,
you can use the TV’s remote control to operate
these devices.
A/ V Receiver Setup. Perform A/V receiver
setup if you want NetCommand to:
Control a surround sound A/V receiver.
Automatically change audio input selections
on an A/V receiver when you change inputs
on the TV.
Automatically change audio and video input
selections on an A/V receiver with an HDMI
output to the TV.
55
56
6. NetCommand IR Control
IR Emitter Placement
VIDEO
L - AUDIO - R
INPUT 3
INPUT 2
R
R
DVI/PC INPUT
L - AUDIO - R
L
AVR AUDIO
OUTPUT
L
R
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
3D GLASSES EMITTER
VIDEO: 480i/480p/720p/1080i/1080p
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p, 1080p
1.
Pr
A/V Receiver
Pb
2.
TV Main
Panel
Pr
Pb
L
YPbPr(480i/480p/720p/1080i)
3.
CH
D I G I T A L
SURROUND
Y
Downloaded From TV-Manual.com Manuals
INPUT 1
5.
sided tape.
Place any unused ends behind the devices to
prevent stray signals from reaching the IR sensors.
S
Y/VIDEO
4. Secure the emitter ends in place using double-
2.
3.
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
The NetCommand system uses emitters connected
to the IR—NetCommand Output jack to control other
devices such as DVD players, cable boxes, satellite
receivers, and VCRs.
1. Connect the plug end of the supplied IR emitter
cable to the IR—NetCommand Output jack on the
TV main panel.
2. Run the cable for each of the emitter ends under,
alongside, or over each device to be controlled so
that the emitter end is in front of the area where the
remote control sensor is located.
3. Position the emitter end with the emitter bulb facing
the remote control sensor. The bulb emits infrared
light in a cone-shaped pattern. Place the bulb far
enough from the sensor to allow the cone pattern
to reach the sensor.
The IR sensor is usually behind the plastic window
of the front display panel. It is sometimes visible
with the aid of a flashlight and is normally a round
or square cutout behind the plastic.
If you cannot see the sensor and the device’s
Owner’s Guide does not specify the location, you
can find it by following these steps using the
device’s remote control:
a. Hold the device’s remote about one-half inch
from the front of the device. Starting from one
end of the display window plastic, press the
POWER key.
b. If the device does not respond, move the
remote control one inch toward the center and
try again.
c. Repeat this until the device responds.
d. Note this location and then start over from the
other end of the display window plastic, repeating until the device responds again.
The remote control sensor is somewhere
between these two positions. This is usually
enough accuracy for placement of the IR emitters.
In some cases, the emitter works better facing
downward from the top of the device. Experiment to find what works best.
ANT-2/AUX
ANT-1/MAIN
Other A/V Device
An IR emitter cable is included with the TV.
Connecting IR—NetCommand Output
*OGSPOUPGBTJOHMF
BWFSBHFTJ[FEEFWJDF
*3TFOTPS
*3TFOTPS
0OUPQPGBTJOHMF
UBMMEFWJDF
*OGSPOUTIBSFECZ
UXPBWFSBHFTJ[FE
EFWJDFT
*3TFOTPS
*3TFOTPS
*3TFOTPS
Place IR emitters so the signal can be “seen” by the IR
sensor on each device.
IMPORTANT
Position IR emitters so that each device’s
sensor “sees” the signal from only one emitter.
Otherwise, a device receiving signals from
multiple sources (remote controls, IR emitters)
may not respond at all.
6. NetCommand IR Control
57
Initial NetCommand Setup for Most Devices
To perform this procedure, you need:
• The remote controls for both the TV and the
device you want to control.
• The IR emitter cable supplied with the TV.
Note:
1.
2.
3.
To set up an A/V receiver, see “Setting Up
NetCommand IR Control of an A/V Receiver,”
page 61.
Connect and position the IR emitters for the
devices you wish to control. See “IR Emitter Placement” on the opposite page.
Set the TV’s remote control slide switch to the TV
position and power on the TV if needed.
Open the NetCommand Learn screen in one of two
ways:
• If working from the Auto Input Sensing screen
for the device, highlight the Learn icon and
press ENTER to open the Learn screen for the
device.
• If performing NetCommand setup at any time
after the device has been recognized through
Auto Input Sensing:
a. Press INPUT to open the Input Selection
menu.
b. Highlight the desired input icon and press
ENTER to switch to that input.
c. Press MENU, highlight Inputs, and highlight
Learn to open the Inputs > Learn screen
for the device.
4. The first function highlighted in the Learn screen
5.
6.
7.
is always Power On. Aim the TV’s remote control
at the TV and press ENTER to begin learning for that
function.
When the Power On text starts flashing, aim the
device’s remote control at the TV and press and
hold the POWER key until a check mark appears next
to Power On.
• If the text stops flashing before the check mark
appears, repeat the previous step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
Press the
keys on the TV’s remote control
to highlight other keys on the list. Repeat steps
4 and 5 for each additional function you wish to
control through NetCommand.
If the device’s remote control has keys that are not
in the list, you can associate up to any four keys
with the F1 through F4 keys. Perform NetCommand
setup for the F keys the same way you did for the
named keys. For example, you can:
• Assign your DVD player’s CHAPTER SKIP FORWARD and
CHAPTER SKIP BACK keys to F1 and F2.
Downloaded From TV-Manual.com Manuals
From the Auto Input Sensing screen, highlight the Learn
icon and press ENTER to open the NetCommand Learn
screen.
Inputs > Learn screen
•
8.
“Learn” your A/V receiver’s sound options for
the current device.
If the device has a separate POWER OFF key, press
on the TV’s remote to highlight Power Off.
Repeat the earlier steps to “learn” the POWER OFF key.
If the device has no POWER OFF key, skip this step.
Do not “learn” the power-off command for the
same key for which you earlier learned the
power-on command.
9. Press EXIT to finish NetCommand “learning” for the
current device.
Adding or Removing Device Keys
from NetCommand IR Control
1. Press INPUT to open the Input Selection menu, high2.
3.
light the device’s icon and press ENTER.
Open the Inputs menu and highlight the Learn icon.
When the Learn screen displays:
• To add keys: Continue as described earlier
under “Initial NetCommand Setup for Most
Devices” on this page.
• To delete keys: Highlight the name of the key
you wish to delete and press CANCEL on the TV‘s
remote control to clear the check mark.
58
6. NetCommand IR Control
NetCommand Specialized Device Keys
Refer to this chart when “learning” device keys. “Learn”
some, all, or none of the keys used for each device
type. The chart has space for you to write in functions
you assign to the F1–F4 keys.
See the following page for more on keys marked in the
“Special Operation Method” column.
Key Name in
Learning Screen
Function
Name on TV
Remote Control
Power On
Power On or Power ON/OFF (toggle)
POWER
Guide
On Screen Program Guide or DVD Disc Menus
GUIDE
Channel Up
Next Channel Higher
CH/PAGE
Channel Dn
Next Channel Lower
CH/PAGE
Page Up
Page Up in Guides
CH/PAGE
Page Dn
Page Down in Guides
CH/PAGE
*
*
Menu
Setup menu for device
MENU
*
Adjust Up
Adjust or arrow up
Adjust Dn
Adjust or arrow down
Adjust Lt
Adjust or arrow left
Adjust Rt
Adjust or arrow right
Enter
Enter or Select (menus)
ENTER
Cancel
Cancel or erase (menus)
—/CANCEL
*
*
Play
Start playback
Stop
Stop playback
Forward
Fast Forward
Rewind
Rewind/Fast Reverse
Pause
Pause playback
Record
Start Recording
1, 2, 3, 4, 5, 6, 7, 8, 9, 0
Digit functions
1, 2, 3, 4, 5, 6, 7, 8, 9, 0
Enter (digits)
Use after digits to directly access channels by
number
ENTER
*
- (separator)
Add digital channel separator between main channel
number and sub-channel number
—/CANCEL
*
Recall (QV)
Last Channel Recall
QV
Info
On-screen status display or information display
INFO
ASSIGN YOUR
CHOICE OF
SPECIALIZED
FUNCTIONS
F1
F2
F3
F4
Power Off
Power Off
Downloaded From TV-Manual.com Manuals
F1
F2
F3
F4
POWER
See Special
Operation
Method Table
*
*
May require two
keypresses
6. NetCommand IR Control
59
Operating NetCommand-Controlled Devices
Controlling Most Device Types
Controlling an A/V Receiver
As an example of NetCommand control, if you are watching your cable box and you wish to tune to the next
channel higher, press CH/PAGE . NetCommand then sends
the “learned” channel-up control signal to the cable box.
See page 61 to set up control of an A/V receiver.
1. With an IR emitter properly positioned in front of the
2.
3.
4.
device, use the Inputs > Learn screen to perform
NetCommand setup for the device.
When you wish to use the device, press INPUT to
display the Input Selection menu.
Press
to highlight the icon for the device.
Press ENTER to switch the TV to the device.
Note:
5.
6.
if you have set up automatic input switching for
the A/V receiver, the A/V receiver will automatically
switch to the correct input for the device.
To operate the device using the TV’s remote
control, set the slide switch to the TV position.
Point the remote control at the TV (not the device)
and press the key for the desired function.
Special Operation Methods
Key Name in
Learning Screen
Power On
Switching Audio to and from the A/V Receiver
1. Press AUDIO.
2. Press to show the Speakers option.
3. Press to select either AV Receiver or TV.
Controlling A/V Receiver Power
1.
2.
3.
4.
Press AUDIO.
Press
to show the Speakers option.
Press to select AV Receiver.
If the A/V receiver does not power on automatically, point
the remote control at the TV (not the A/V receiver) and
press POWER. Press POWER to power off the A/V receiver.
Controlling Other A/V Receiver Functions
With the A/V receiver powered on and selected, the
TV’s remote operates the volume and mute functions.
Also, when you switch to a device in the Input Selection menu, the A/V receiver automatically switches to the
correct audio input for the device.
Special Operation Description and Setup
How to Use
Manual Power On/Off
Use for devices that have only one POWER key.
1. Press INPUT to display the Input Selection
menu.
2. Press
to highlight the icon for the
device to be powered on or off.
3. With the Input Selection menu still displayed,
press POWER to send the power signal; you may
need to press POWER twice.
Note:
If you press POWER without the Input Selection menu displayed, the TV will turn off.
4. Press ENTER to switch the TV to the device.
Power On
Power Off
Menu
Automatic Power On/Off
•
This feature is only for devices that have separate
POWER ON and POWER OFF keys on their original remote
controls. If your device does not have a separate
POWER OFF key, do not use the Power Off learning position; use only the Manual Power ON/OFF
method described above.
In the NetCommand Learn screen:
a. “Learn” the Power On command in the Power •
On learning position.
b. “Learn” the Power Off command in the
Power Off learning position.
Displaying the Menu for a Device
Downloaded From TV-Manual.com Manuals
To Power On the Device
1. Press INPUT to display the Input Selection
menu.
2. Press
to highlight the icon for
the device to be powered on or off.
3. Press ENTER to switch the TV to the device
and NetCommand will send the Power On
command to the device.
To Power Off the Device
When you turn the TV off, the TV sends all
learned Power Off commands to all devices.
1. While watching a device, press INPUT to display
the Input Selection menu with the device icon
highlighted.
2. Press MENU to send the menu signal to the
device. The Input Selection menu will automatically clear from the screen.
60
6. NetCommand IR Control
Operating NetCommand-Controlled Devices, continued
Key Name in
Learning Screen
Guide
Special Operation Description and Setup
How to Use
Displaying the Disc Menu (DVD or high-definition disc format)
While watching the device, press GUIDE to display
the disc menu.
“Learn” the DISC MENU, TOP MENU, or other key as
named on the original remote in the Guide learning position.
Displaying the On-Screen Program Guide
(cable box or satellite receiver)
1. “Learn” the GUIDE key on the original remote in
the Guide learning position.
2. Learn the PAGE
and PAGE
keys of the
original remote in the Page Up and Page Dn
learning positions.
Page Up
Page Dn
Enter
1. While watching the device, press GUIDE to
display the guide.
2. Press CH/PAGE
/
to send the Page Up/Dn
commands for the guide.
Using Page Up/Down
•
If the device’s original remote control has separate
keys for Channel Up/Dn and Page Up/Dn, the TV
remote control’s CH/PAGE
/
key can work like
•
the two separate keys.
1. “Learn” CHANNEL / in the Channel Up/Dn
positions.
2. “Learn” PAGE / in the Page Up/Dn positions.
Inside the Guide
/
Press CH/PAGE
commands.
to send the Page Up/Dn
Outside the Guide
Press CH/PAGE
Dn signal.
/
to send the Channel Up/
Enter Functions (cable boxes, satellite receivers, etc.)
Some devices have two keys that have “enter” functions. One key is for menus and is often labelled
SELECT or OK. A second key is for use with number keys for direct channel selection. NetCommand uses
the same ENTER key for both operations.
When ENTER has a menu or guide function or when
the original remote control uses the same key for
menus and channel selection:
Learn the ENTER, SELECT, or OK key in the
NetCommand Enter learning position.
1. Press MENU or GUIDE to display the device’s menu
or guide.
2. Press ENTER within the menu and NetCommand
will send the Enter signal for menus.
Enter (digits) When ENTER is for channel changes, i.e., the original Press digit key(s) and then press ENTER.
remote control has a separate ENTER key for this
NetCommand will send the Enter signal for
channel selection.
function):
Learn the ENTER key for channel selection in the
NetCommand Enter (digits) learning position.
Use this learning position only if the original
remote control has separate keys for Enter in
menus and Enter for channel selection.
Cancel
CANCEL as the Cancel or Exit Function
“Learn” the Cancel or Exit function in the
NetCommand Cancel learning position
—
(separator)
The symbol “—” can serve as the separator
between a digital channel’s main and subchannel digits, e.g., digital channel 12-1 (main
channel is 12, sub-channel is 1).
“Learn” the channel separator function in the
NetCommand – (separator) learning position.
Downloaded From TV-Manual.com Manuals
1. Press MENU or GUIDE to display the menu or
guide.
—
2. Press CANCEL and NetCommand will send the
Cancel or Exit signal.
—
Press digit key(s) and press CANCEL .
NetCommand will send the channel-separator
signal.
61
6. NetCommand IR Control
Setting Up NetCommand IR Control of an A/V Receiver
Several types of A/V receiver control can be set up
using the Inputs > AV Receiver menu, shown on the
following pages.
• Controlling power and volume is described on this
page.
• Automatic audio switching, suitable for most equipment setups, is described under “A/V Receiver
Control: Automatic Audio Switching (non-HDMI
A/V receiver)” on the next page.
• Automatic audio and video switching can be set up
If your A/V receiver has an HDMI output. You can
send audio and video from multiple devices to the
A/V receiver and then through a single cable to the
TV. See “A/V Receiver Control: Automatic Audio
and Video Switching via HDMI,” page 64.
Note:
To set up control of other device types, see
“Initial NetCommand Setup for Most Devices,”
page 57.
AV Receiver screen.
Perform NetCommand
IR “learning” for A/V
receiver power and
volume keys.
3. When the Power On text starts flashing, aim the
A/V receiver’s remote control at the TV and press
and hold the POWER or POWER ON key until a check mark
appears next to Power On.
• If the text stops flashing before the check mark
appears, repeat this step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
4. Press the
key on the TV’s remote control to highlight
other keys in the list. Repeat steps 2 and 3 for each additional function you wish to control through NetCommand.
A/V Receiver Control: Power and Volume
Perform this setup to operate the A/V receiver’s power
and volume functions with the TV’s remote control.
5. If the A/V receiver has a separate POWER OFF key,
To perform this setup you need:
• The remote controls for both the TV and the
A/V receiver.
• The IR emitter cable supplied with the TV.
Before You Begin
1. Connect your A/V receiver to the TV and any addi2.
3.
tional devices. See chapter 3, “TV Connections,”
for suggestions.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 56.
Set the TV’s remote control slide switch to the TV
position and power on the TV if not already on.
6.
press on the TV’s remote to highlight Power Off.
Repeat steps 2 and 3 to “learn” the POWER OFF key. If
the A/V receiver has no POWER OFF key, skip this
step. Do not “learn” Power Off for the same key
for which you learned Power On.
When finished “learning” the power and volume
keys, either press EXIT to watch TV or leave the AV
Receiver screen open to continue with NetCommand setup to control switching of A/V receiver
inputs.
Setup to Control A/V Receiver Power and Volume
1. Open the AV Receiver screen in one of two ways:
•
2.
If using the Auto Output or Auto Input
Sensing screen for the A/V receiver, highlight
the Learn icon and press ENTER to open the AV
Receiver screen.
• If performing NetCommand setup at any time
after the A/V receiver has been recognized
through Auto Output/Auto Input Sensing:
Press MENU, highlight Inputs, and highlight AV
Receiver to open the AV Receiver screen.
The first function highlighted in the AV Receiver
screen is always Power On. Aim the TV’s remote
control at the TV and press ENTER to begin learning
for Power On.
Downloaded From TV-Manual.com Manuals
IMPORTANT
To hear audio sent from the TV to the A/V receiver,
you must have:
• Physically connected the TV to the A/V receiver
via the analog or digital audio output.
• Assigned, if needed, the name AVR if using an
HDMI A/V receiver.
• Selected the A/V receiver as the audio source.
Press AUDIO, then
to show the Speakers
option, then to select the A/V Receiver.
• “Learned” the IR codes for the A/V receiver
inputs.
• Assigned the TV’s audio output to the correct
input in the NetCommand A/V Receiver Learn
screen.
62
6. NetCommand IR Control
Setting Up NetCommand IR Control of an A/V Receiver, continued
A/V Receiver Control: Automatic Audio Switching (non-HDMI A/V receiver)
Perform one of these setups to enable the A/V receiver
to switch automatically to the correct audio input when
you select a device in the TV’s Input Selection menu.
To set up control of an A/V receiver you need:
• The remote controls for both the TV and the A/V
receiver.
• The IR emitter cable supplied with the TV.
• Connecting cables
ment. To switch both audio and video via an HDMI
connection, see page 65.
Audio Switching Setup 1: Automatic A/V Receiver
Switching to TV Audio Input
Audio Switching Setup 2: Automatic A/V Receiver
Switching to a device sending audio directly to the A/V
receiver. You must use setup 2 to hear digital surround sound from the source device.
Two different setups are described here. Review the
descriptions to find the setup needed for your equip-
Note:
Audio Switching Setup 1: Audio
from TV’s Audio Output
Audio Switching Setup 2: Audio from Source Device
audio + video
analog audio
video
VCR with
Analog Audio Output
TV
audio output from
TV (digital or analog)
TV audio
out
DVD audio
input
TV audio input
A/V Receiver
Incoming Coaxial Cable
to ANT 1/ANT 2
Audio Switching Setup 1: Audio to the A/V receiver
from the TV’s digital or analog audio output
•
•
•
Audio Available from TV only
Audio from ANT 1 and ANT 2 must be sent to
the A/V receiver from the TV’s DIGITAL AUDIO
OUTPUT or analog AVR AUDIO OUTPUT.
Use Setup 1 to make the A/V receiver switch to its
designated TV audio input when viewing these sources.
Analog Stereo Audio
Audio from sources with only analog stereo output
(such as a VCR) can be sent either directly to the
A/V receiver or through to the TV and then on to the
A/V receiver.
Mitsubishi recommends you send audio through
the TV as shown in the example. Setup 1 causes
the A/V receiver to switch to its input designated for
TV audio.
If you have a digital A/V receiver, the TV makes the
audio available by converting analog audio to a
digital output.
HDMI Digital Stereo Audio
Digital stereo audio from an HDMI connection
is available both in digital format (from the TV’s
DIGITAL AUDIO OUTPUT jack) and in analog
format (from the TV’s AVR AUDIO OUTPUT jack).
Downloaded From TV-Manual.com Manuals
Automatic audio and video switching over an
HDMI cable is covered on page 65.
%7%1MBZFS EJHJUBMTVSSPVOETPVOE
XJUI
%JHJUBM
4VSSPVOE
WJEFP
4PVOE
57
%7%BVEJP
JOQVU
"73FDFJWFS
Audio Switching Setup 2: Audio from a device
providing surround sound is sent directly to the A/V
receiver.
Note: This setup is required to hear digital surround sound
A device can send digital surround sound such as
Dolby Digital or DTS directly to the A/V receiver,
bypassing the TV entirely. The device might be a DVD
player, cable box, or satellite receiver, and could have
HDMI output. A DVD player is used in this example.
Your setup may include additional devices with digital
surround sound connected directly to the A/V receiver.
These devices might be a DVD player plus a cable box
or satellite receiver.
6. NetCommand IR Control
63
Setting Up NetCommand IR Control of an A/V Receiver, continued
Before You Begin
ceiver menu are arbitrary names used by the TV
to uniquely identify A/V receiver inputs.
1. Connect your A/V devices to the TV and connect
2.
3.
your A/V receiver to the audio outputs on the TV and
the DVD player. See chapter 3, “TV Connections,” for
suggestions. Important: To use Setup 1, you must:
• Connect the A/V receiver to the TV’s audio
output; i.e., the TV’s AVR AUDIO OUTPUT or
DIGITAL AUDIO OUTPUT jack.
• Set the AV > Audio menu Speakers option to
AV Receiver.
Position NetCommand IR emitters as described in
“IR Emitter Placement,” page 56.
Open the Inputs > AV Receiver menu.
Note:
Audio Switching Setup 1: Automatic A/V Receiver
Switching to the TV Audio Input
Most devices are set up to use the TV’s audio output like
the VCR in this example; analog audio from the device is
sent through the TV to the A/V receiver’s TV audio input.
Use this setup for:
• Sources providing only analog stereo output,
such as a VCR.
• Audio from ANT 1 and ANT 2
1. Under Learn, highlight Input1.
The terms Input1–Input5 used in the AV Re-
2.
3.
A
B
D
C
AV Receiver menu to set up audio switching
A The Learn column lists “learnable” input keys on
the A/V receiver’s remote control.
B A check mark next to a key name indicates it has
been “learned” by NetCommand.
4.
In this example, the IR code for the A/V receiver’s
TV Audio input will be “learned” as Input 1.
Press ENTER on the TV’s remote control.
While the text Input1 is flashing, press and hold the
TV INPUT key on the A/V receiver’s remote control.
When a check appears next to Input 1, release the
TV INPUT key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press CANCEL
while the name is highlighted.
5. Press
once to highlight TV Audio (TV audio
output) in the Assign Input1 column. The triangular
marker is always next to the assigned sound source.
6. Press EXIT if finished or continue with setup for
another TV audio source.
C Input1 through Input5 are arbitrary names the
TV uses to uniquely identify A/V receiver inputs.
D After “learning” IR codes for A/V receiver inputs,
use the Assign Input column to identify the device
connected to the TV and the associated A/V
receiver input.
For the given example:
1. Connect the TV’s audio output to the A/V receiver’s
TV audio input.
2. Using this screen, “learn” the IR code for the A/V
receiver’s TV audio input as Input1 (item C above).
3. In the Assign Input1 column (item D above), assign
the name TV Audio (the default) to the A/V receiver
IR code previously learned as Input1.
4. Connect the DVD player’s audio output to the A/V
receiver’s DVD input.
5. Using this screen, “learn” the IR code for the A/V
receiver’s DVD audio input as Input2.
6. In the Assign Input2 column, assign the name DVD
to the A/V receiver IR code previously learned as
Input2 in this screen.
Downloaded From TV-Manual.com Manuals
Completed NetCommand setup described for
controlling A/V receiver switching to the A/V receiver’s
audio input from the TV’s AUDIO OUTPUT.
IMPORTANT
All audio from what you are watching on the TV is
always available from both the TV’s AVR AUDIO
OUTPUT and DIGITAL AUDIO OUTPUT jacks.
To use the digital surround sound capabilities
of your A/V receiver however, you must connect
your DVD player, satellite receiver, or cable box
directly to the A/V receiver, as surround sound
may not be available from the TV’s audio output.
64
6. NetCommand IR Control
Setting Up NetCommand IR Control of an A/V Receiver, continued
Audio Switching Setup 2: Automatic A/V Receiver
Switching to a Surround Sound Device
A/V Receiver Control: Automatic Audio
and Video Switching via HDMI
Use this setup to send digital surround sound directly
from a device to an A/V receiver.
1. Under Learn, highlight Input2.
In this example, the IR code for the A/V receiver’s
DVD Audio input will be “learned” as Input2.
2. Press ENTER on the TV’s remote control.
If your A/V receiver has an HDMI output, you can use
this procedure to set up control of the A/V receiver’s
audio and video switching. The HDMI connection
allows you to route video signals from multiple devices
over a single cable to the TV. See the diagram on the
opposite page. The connected devices can be analog,
digital, or a mixture or the two.
%7%1MBZFS EJHJUBMTVSSPVOETPVOE
XJUI
%JHJUBM
4VSSPVOE
WJEFP
4PVOE
57
%7%BVEJP
JOQVU
"73FDFJWFS
More About Using an HDMI Connection
•
Audio from devices connected directly to the TV
can be heard from the TV speakers only. This is
because audio signals are sent on the HDMI cable
in one direction only—through the A/V receiver to
the TV speakers.
To send audio to the A/V receiver from a device
connected directly to the TV, use one of the optional
audio connections shown in the diagram. For
example, use an optional audio connection if you
wish to use the A/V receiver speakers to hear audio
from:
- The ANT 1 or ANT 2 inputs
- A device connected to the convenience input
(INPUT 4), such as a game or camcorder.
•
In some circumstances, audio from a device connected to the A/V receiver may not be passed over
the HDMI cable to the TV speakers. You must use
the A/V receiver speakers to hear audio in these
cases.
Setup 2: A/V receiver audio from a device providing
surround sound directly to the A/V receiver
Completed NetCommand setup described for
controlling A/V receiver switching to an A/V receiver
input “learned” as Input2.
3. While the text Input2 is flashing, press and hold the
4.
DVD INPUT key on the A/V receiver’s remote control.
When a check appears next to Input2, release the
DVD INPUT key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press CANCEL
while the name is highlighted.
5. Press
6.
7.
once to move the highlight to the Assign
Input2 column.
Use
to highlight DVD in the list of devices
recognized by the TV. The triangular marker always
shows the assigned sound source.
Press EXIT if finished or continue for additional TV
sources.
Before You Begin
To complete these steps you will need:
• The remote controls for both the TV and the
A/V receiver.
• The IR emitter cable supplied with the TV.
• An HDMI-to-HDMI cable to connect the A/V
receiver to the TV and cables necessary to
connect devices to the A/V receiver.
1. Connect your audio/video devices to the A/V
2.
3.
Downloaded From TV-Manual.com Manuals
receiver. Note the name of the device connected
to each A/V receiver input. This information will be
needed later to set up NetCommand’s automatic
input switching.
Connect the A/V receiver to the TV with an HDMIto-HDMI cable.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 56.
6. NetCommand IR Control
65
Setting Up NetCommand IR Control of an A/V Receiver, continued
VCR
4. Power on the A/V receiver.
5. Set the TV’s remote control slide switch to the TV
Cable box
6.
DVD player
High-definition
DVD player
position and power on the TV if needed.
When the Auto Input Sensing screen displays,
select device name AVR.
Setup to Control A/V Receiver Power and Volume
Perform the steps under “A/V Receiver Control: Power
and Volume,” page 61.
TV main
panel
ANT-2/AUX
ANT-1/MAIN
A/V receiver with
HDMI output
AUDIO DIGITAL HDMI
AUDIO IN OUT
IN
Setup to Control Switching to the TV’s Audio Output
VIDEO
Y
Y/VIDEO
INPUT 1
INPUT 3
AVR AUDIO
OUTPUT
L
R
L
DVI/PC INPUT
L - AUDIO - R
DIGITAL
AUDIO OUTPUT
INPUT 2
Pr
L - AUDIO - R
Pb
Pr
Pb
L
YPbPr(480i/480p/720p/1080i)
R
DIGITAL
AUDIO OUTPUT
R
AVR AUDIO
OUTPUT IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
L
R
If you have used an audio connections to the TV’s
AVR AUDIO OUTPUT or DIGITAL AUDIO OUTPUT jacks,
it is recommended that you set up NetCommand to
control switching to the TV audio input. Perform the
steps under “Audio Switching Setup 1: Automatic A/V
Receiver Switching to the TV Audio Input,” page 63.
Setup to Control Automatic Audio
and Video Switching via HDMI
Optional
recommended
analog or digital
audio connection
3D
D GLASSES EMITTER
Follow these steps if you wish NetCommand to control
switching of A/V receiver video as well as audio inputs.
When this setup is complete, you can use the TV’s
Input Selection menu to select a video device connected to the A/V receiver. You can also perform additional NetCommand setup to control devices connected
to the A/V receiver.
HDMI
cable
Multiple video inputs on a single HDMI cable. You can
connect multiple video devices to an A/V receiver that
has an HDMI output. The optional audio connection
allows you to hear, through the A/V receiver, devices
connected to the TV only.
1. Display the Inputs > AV Receiver menu.
Note:
2.
The labels Input1 through Input5 in the Learn
column are names used by the TV to uniquely
identify A/V receiver inputs.
With the highlight in the Learn column, highlight
one of the Input labels Input2 through Input5; it
is recommended you leave Input1 reserved for TV
Audio.
AV Receiver menu for audio and video switching
with HDMI output
1
4
3
1 The Learn column lists “learnable” keys from the
A/V receiver’s remote control.
2 Input1 through Input5 are arbitrary names used
by the TV to uniquely identify “learnable” A/V
receiver inputs.
3 A check mark next to a key name indicates it has
been “learned” by NetCommand.
2
Downloaded From TV-Manual.com Manuals
4 The Assign Input column provides a list of
possible device types. Select from this list the
device type connected to the associated A/V
receiver input. The assigned device name will
appear in the Input Selection menu.
66
6. NetCommand IR Control
Setting Up NetCommand Control of an A/V Receiver, continued
8. Press EXIT if finished or repeat these steps for additional video sources connected to the A/V receiver.
NetCommand IR Control: Device
Connected to an A/V Receiver
3. Press ENTER and the highlighted Input label will start
4.
5.
flashing to indicate readiness for “learning.”
While the Input text is flashing, press and hold the
key on the A/V receiver’s remote control for the
input you wish to associate with the selected Input
label.
When a check appears next to the Input label,
release the remote control key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press CANCEL
while the name is highlighted.
Use this setup to have NetCommand control a device
sending audio and video through the A/V receiver to the
TV via HDMI. In the case of an analog source device,
the A/V receiver must be able to digitize the signal for
HDMI output.
1. Set up NetCommand control of A/V receiver audio/
video switching via HDMI as described on the previous page.
Source
Device
Any Connection Type
A/V Receiver
HDMI
Cable
TV
2. Press EXIT to close any open menus and return to
normal TV viewing.
Press INPUT to open the Input Selection menu.
3.
4. Highlight the icon for the source device connected
5.
6. On the TV’s remote control, press
7.
once. The
highlight will move automatically to the associated Assign Input column (Assign Input1 through
Assign Input5).
Use
to highlight the device type connected to
the A/V receiver input just “learned.” The Assign
Input column contains a list of possible device
types.
In the example above, a DVD player is connected to
the A/V receiver input the TV knows as Input2.
The device type you select here will appear as an
icon in the TV’s Input Selection menu. You can
assign each device type in the list only once.
Downloaded From TV-Manual.com Manuals
6.
7.
to the A/V receiver input you wish to control.
The A/V receiver’s remote control key for the input
must have been “learned” previously using “Setup
to Control Automatic Audio and Video Switching via
HDMI” on the previous page.
Press ENTER to switch the TV to the A/V receiver and
the A/V receiver to the device.
Open the Inputs > Learn menu.
Perform NetCommand “learning” for the device by
following the steps in “Initial NetCommand Setup
for Most Devices,” page 57.
67
Appendices
Appendix A:
Appendix B:
Appendix C:
Appendix D:
Appendix E:
Specifications . . . . . . . . . . . . . . . . . . .
Bypassing the Parental Lock . . . . . . . . . .
Programming the Remote Control . . . . . . .
NetCommand HDMI Control of CEC Devices .
Troubleshooting . . . . . . . . . . . . . . . . . .
Downloaded From TV-Manual.com Manuals
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
68
69
71
78
82
68
Appendices
Appendix A: Specifications
Size, Weight, and Power Consumption
Dimensions (inches)
Model
Height
L65-A90
39.8
Width
57.7
Depth
10.05
Outputs
Weight
(lbs.)
Power
(watts)
141.5
180
Description
Qty.
Audio Speakers
2
Qty.
Input Specifications
Antenna/Cable
input
2
RF
F connector, 75-ohm
HDMI (digital
video/audio)
4
CEA-861D standard for digital audio
and video via HDMI
HDMI standard connector
Video:
60 Hz: 480i, 480p, 720p, 1080i
24 Hz, 30 Hz, 60 Hz: 1080p
Audio: PCM stereo
HDMI inputs are compliant with
CEA-861D standards for standard,
extended, and high-definition video;
digital audio, and HDCP copy protection.
PC (digital signals only):
VGA (640 x 480, 60 Hz)
W-VGA (848 x 480, 60 Hz)
SVGA (800 x 600, 60 Hz)
W-SVGA (1064 x 600, 60 Hz)
XGA (1024 x 768, 60 Hz)
1280 x 720, 60 Hz
SXGA (1280 x 1024, 60 Hz)
1920 x 1080 (24 Hz, 30 Hz, 60 Hz)
WXGA (1360 x 768, 60 Hz))
Composite
Video
up
to 3
NTSC 480i only
Video:
RCA Pin Plug, 1.0 V p-p,
75 ohm
1 dedicated composite video jack; 2
shared with component video Y
S-Video
Component
Video (Y/Pr/Pb)
1
Four-Pin DIN Plug
Y: 1.0 Vp-p 75-ohm
C: 0.286 Vp-p (burst signal), 75-ohm
up to 3 CEA-770.1 & CEA 770.2 480i, 480p,
sets CEA 770.3 720p and 1080i (TV
analog component video standards)
RCA Pin Plug
Y:
1.0 Vp-p (includes sync),
75-ohm
Pr: 700 mV p-p, 75-ohm
Pb: 700 mV p-p, 75-ohm
1 dedicated set of component video
jacks; 2 sets share a jack with composite video
USB Photo Port
Audio Inputs
1
5
pairs
For transfer of JPEG files only.
Analog left and right audio
RCA Pin Plug 500 mV (full scale), 43-k
ohm
Downloaded From TV-Manual.com Manuals
5.75" x 2.4"
RCA Pin Plug, 500 mV rms + 200 mV
(full scale) for analog sources, 1.5
Vrms + 0.5 Vrms (full scale) for digital
sources.
Analog Audio
(Signal)
1
pair
Digital Audio
Output
1
RCA Pin Plug, Signal Type Dolby
Digital, PCM stereo
3-D Glasses
Emitter
1
VESA 1997-11 Connector and Signal
Standards for Stereoscopic Display
Hardware
Inputs
Type
Output Specifications
Image Technology
DLP, 0.65” chip, 1920 x 1080 pixels with Smooth Picture™
Channel
Frequency
Reception
Over-the-Air: VHF 2–13, UHF 14–69
Analog Cable: 1–125
Digital Cable: 1–135
Over the Air:
Analog NTSC, Digital ATSC with
sub-channels (all 18 video formats)
Cable:
Analog NTSC (non-scrambled)
Digital QAM 64 and 256 with subchannels (non-scrambled)
Channel
Type*
* Note for Digital Channels: The channel numbers displayed
on screen are determined by the broadcaster or cable company
and can vary from the standard frequency number. If there is no
channel-number information provided by the broadcaster or cable
company, the TV creates a channel number. The created channel
number uses the frequency number as the main channel number
and the program number as the sub-channel number.
Appendices
69
Appendix B: Bypassing the Parental
Lock
Bypassing the Parental Lock
Lock Bypass Instructions Have Been Filed for
Future Reference
After you set the lock, you must use your pass code
to view a locked program, view the locked TV, view
a locked channel, cancel the lock, or enter the Lock
menus.
IMPORTANT
Cut along the dotted line and file bypass
instructions in a safe place for future reference.
Downloaded From TV-Manual.com Manuals
If you forget your pass code, you can view the locked
TV without entering your pass code. When you are
prompted for your pass code, press the number 9 and
QV keys on the TV remote control at the same time. This
process temporarily unlocks the TV.
When entering the Lock menu, this process deletes
your old pass code and prompts you to enter a new
pass code.
•
You can either enter a new pass code to open the
Lock menu and make changes or press EXIT to close
the menu.
•
If any of the locks are turned on and you exit the
menus when prompted for a new code, the old
code and all lock settings are retained.
•
If all locks are turned off and you exit the menus
when prompted for a new code, then the previous
code is erased.
IMPORTANT
When changing or deleting your pass code,
you must use the remote control included
with this TV. You cannot use a Mitsubishi
remote control from another component or a
“universal” remote.
70
Appendices
This page intentionally left blank
Downloaded From TV-Manual.com Manuals
71
Appendices
Appendix C: Programming the Remote Control
This appendix explains programming the TV’s remote
control to operate other A/V devices. This is distinct
from NetCommand control. The TV’s remote control
can operate other devices by three different methods:
VCRs and DVRs
•
Remote Control Programming: You must move
the slide switch to the position specific to the
type of device.
•
•
•
•
•
•
•
NetCommand® IR “learning”: You can operate
other devices with the slide switch in the TV
position.
Mitsubishi VCRs are compatible with some additional
keys.
•
NetCommand for HDMI devices: You may be
able to operate compatible CEC-enabled HDMI
devices with the slide switch in the TV position.
See the device’s Owner’s Guide and Appendix
D.
Functions Available for Other A/V Devices
The TV’s remote control can be programmed to operate
other types and brands of A/V products. To use the
remote when programmed, set the slide switch to the
position labelled for the product type. The functions
performed in each switch position can vary depending
on the product. Not all functions work for all models.
The most common functions available are listed on this
page.
CH
/
POWER
SLEEP
(FAST FORWARD)
(PAUSE)
(PLAY)
•
•
•
•
•
•
(RECORD)
(REVERSE)
(STOP)
GUIDE (DVR only)
MENU (DVR only)
0–9 Number Keys
Cable Boxes and Satellite Receivers
•
•
•
•
•
•
•
•
•
•
AUDIO (PAGE UP)
QV CANCEL (last channel
on some models)
CH
/
ENTER (on some models)
GUIDE (on some models)
LIST
POWER
(on some
models)
VIDEO (PAGE DOWN)
QV or CANCEL (ENTER for
channels on some
models)
•
•
0–9 Number Keys (on
some models)
F1–F4 (A, B, C, D keys
on some models)
The record/playback keys
(on some models):
•
(FAST FORWARD)
•
(PAUSE)
•
(PLAY)
•
(RECORD)
•
(REVERSE)
•
(STOP)
A/V Receivers
•
•
•
•
•
MUTE
POWER
SLEEP
VOLUME
0–9 Number Keys
•
Direct Input Selection keys: numbers,
FAV and QV (on some
Mitsubishi models)
CD Players
(not all functions for all models)
Set the remote control’s slide
switch to the type of device you
wish to program for or control.
•
•
•
•
SLEEP
(FAST FORWARD)
(PAUSE)
(PLAY)
•
•
•
(REVERSE)
(STOP)
0–9 Number Keys
DVD and Laser Disc Players
(not all functions for all models)
•
•
IMPORTANT
Some manufacturers may change their
products or they may use more than one
remote control system. The TV’s remote
control may be unable to operate your A/V
equipment in these cases.
Downloaded From TV-Manual.com Manuals
•
•
•
•
•
CANCEL (on some
models)
CH
/
(for track
skip on some models)
ENTER
MENU
POWER
SLEEP
(on some
models)
•
•
•
•
•
•
•
(FAST FORWARD)
(PAUSE)
(PLAY)
(RECORD)
(REVERSE)
(STOP)
0-9 Number Keys (on
some models)
72
Appendices
Appendix C: Programming the Remote Control, continued
Programming the Remote Control
6. Once you have found the correct code, write it in
the space below for future reference.
1. Move the slide switch at the top of the remote to
the position for the product you want to control.
Refer to the table below. Only one of each device
type can be controlled in each slide-switch position.
Switch Position
Device Type
Code
CABLE/SAT
VCR
Switch Position
Affected Device
CABLE/SAT
Cable Box
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
Laser Disc Player
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
Laser Disc Player
VCR
AUDIO
A/V Receiver
Audio Amplifier
CD Player
2. Press and hold POWER on the remote control for
several seconds until the key blinks twice and goes
off.
Release the POWER key.
DVD
AUDIO
Code Verification
To determine the code programmed for any position of
the slide switch:
1. Move the slide switch to the position you wish to
verify.
2. Press and hold POWER on the remote control for
several seconds until the key blinks twice and goes
off.
3. Press keys 9 9 0
4. Press 1 and count the blinks of the power key.
5.
Write down the number of blinks as the first digit of
the code.
Repeat step 4 for the second, third, fourth, and fifth
digits of the code.
3.
4. Enter the first five-digit code listed for your equip-
5.
ment.
• The POWER key blinks twice when you start to
enter the code and then once for each additional keypress.
• The POWER key blinks twice when you finish
entering a valid code.
• Move the slide switch to another position if you
need to start over or wish to exit programming
mode.
Point the remote control at the equipment and
press POWER. If the product has no power on/off
function, press a different key, such as
(PLAY),
(STOP), VOL , or MUTE.
• If the equipment responds, the remote control
is properly programmed to operate the equipment.
• If the equipment does not respond, repeat
steps 2–4 with the next five-digit code listed for
your equipment.
Audio Lock: Universal A/V Receiver Control
With Audio Lock active, the remote control operates
the volume and mute functions of the A/V receiver in all
positions of the slide switch. Activate Audio Lock if you
normally use an A/V receiver with your TV and other
A/V equipment.
1. Program the AUDIO position for your A/V receiver as
2.
3.
The POWER key will blink twice to indicate Audio Lock
is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
1. Press and hold POWER for several seconds until the
2.
IMPORTANT
You may need to reprogram the remote
control after changing the batteries.
Downloaded From TV-Manual.com Manuals
described earlier in this section.
With the slide switch in the AUDIO position, press
and hold POWER on the remote control for several
seconds until the key blinks twice and goes off.
Press keys 9 9 3 ENTER
key blinks twice and goes off.
Press keys 9 9 3 VOL .
The POWER key will blink four times to indicate Audio
Lock has cleared.
73
Appendices
Appendix C: Programming the Remote Control, continued
Programming Codes
Audio Amplifiers
Make
Code
Acurus
Adcom
Altec Lansing
Aragon
Bel Canto
Design
Bose
Carver
Cary Audio
Design
Classe
Curtis Mathes
Durabrand
Flextronics
GE
Halcro
Harman/
Kardon
JVC
Klipsch
Krell
Left Coast
Lenoxx
Lexicon
Marantz
Mark Levinson
McIntosh
Modulaire
Mondial
Optimus
30765
31100, 30577
31742
30765
31583
Parasound
Philips
Pioneer
Polk Audio
Primare
RadioShack
RCA
Realistic
Soundesign
Technics
Victor
Wards
Yamaha
30674
30892
31879
31461
30300
31561
31879
30078
31934
30892
30331
30765
31837
30892
31561
31802, 31145
30892
31483
30251
30395
30765
30823, 30395, 30300,
30013
31934
30892
30823, 30300, 30013
30892
31395
30395
30823, 30300, 30013
30013, 30395
30078
30372
30331
30078, 30013
30354
Cable Boxes
Make
Code
A-Mark
ABC
Accuphase
Acorn
Action
Active
Americast
Archer
BCC
Bell & Howell
Bell South
British
Telecom
Century
Clearmaster
10144, 10008
10237, 10014, 10011,
10008, 10007, 10003
10014, 10011, 10007,
10003
10237
10237
10237
10899
10237
10276
10014
10899
10003
10008
10883
Cable Boxes
Make
Code
Cable Boxes
Make
Code
CD Players
Make
Code
ClearMax
Comtronics
Cool Box
Coolmax
Digeo
Digi
Director
Dumont
Emerson
Everquest
Fosgate
GC Electronics
GE
General
Instrument
Signal
Signature
SL Marx
Sony
Sprucer
Starcom
Stargate
Storm
Supercable
Supermax
Teleavia
Teleview
Thomson
Timeless
Tocom
Torx
Toshiba
Tristar
TV86
United Artists
United Cable
10040, 10011
10011
10040
11006
10144
10014, 10003
10040, 10014
10637
10276
10883
10040
10040
11256
10040
10012
10003
10000
10883
10040
10007
10276, 10014, 10011,
10003
10276, 10008, 10003
Hitachi
Inkel
Integra
Jerrold
JVC
Kenwood
10883
10000
10883
10883
10883
10899, 10525, 10000
MGA
Micromega
Miro
Mission
Mitsubishi
Modulaire
Gibralter
GMI
GoldStar
Hamlin
Hitachi
Houston
Hytek
Hytex
Insight
Jebsee
Jerrold
Memorex
Mitsubishi
Motorola
Multitech
Nova Vision
Novaplex
NSC
Oak
Pace
Panasonic
Panther
Paragon
Penney
Philips
Pioneer
Prism
Pulsar
Pulser
Quasar
R-Line
RadioShack
RCA
Regal
Regency
Rembrandt
Runco
Samsung
Scientific
Atlanta
Downloaded From TV-Manual.com Manuals
10883
10040
10883
10883
11187
10637
10476
10637
10014
10040
10276
10040
10144
10810, 10476, 10276,
10020, 10014, 10012,
10011, 10003
10003
10883
10144, 10040
10273, 10259, 10020
10011, 10008, 10003
10011
10007
10007
10476, 10810
10014
10810, 10476, 10276,
10020, 10014, 10012,
10011, 10003
10000
10003
11376, 11254, 11187,
11106, 10810, 10476,
10276, 10014
10883
10008
10008
10637, 10012
10007
11877, 10877, 10237,
10008
10144, 10107, 10008,
10000
10637
10525, 10008, 10000
10637, 10000
11305, 10317, 10259
11877, 10877, 10533,
10144
10012
10040, 10000
10040
10000
10040
10883
11256
10279, 10276, 10273,
10259, 10020
10020
10040, 10011
10000
10144, 10040, 10003
11877, 10877, 10477,
10237, 10012, 10008,
10003, 10000
US Electronics
V2
Videoway
Viewmaster
Vision
Vortex View
Zenith
CD Players
Make
Code
Acoustic
Research
Aiwa
Akai
Arcam
Audio Pro
Audio
Research
Burmester
Cairn
California
Audio Labs
Cambridge
Soundworks
Carver
Cary Audio
Design
Classic
Curtis Mathes
Denon
DKK
DMX Electronics
Fisher
Garrard
Genexxa
GPX
Grundig
Hafler
Harman/
Kardon
30420
30157
30083
30157
30437
30157
30420
30157
30303, 30029
30157
30437, 30179, 30157
31876
31297
30032
30766, 30034, 30003
30000
30157
31325, 30179, 30000
30420
30032
31296
30157
30173
31202, 30173, 30157,
30100, 30083
KLH
Koss
Krell
LG
Linn
LXI
Magnavox
Marantz
Mark
Levinson
Matsui
McIntosh
MCS
Memorex
MTC
Myryad
NAD
NSM
Onkyo
Optimus
Panasonic
Parasound
Penney
Philips
Pioneer
Polk Audio
Primare
Proceed
Proton
QED
Quad
Quasar
RadioShack
RCA
Realistic
Revox
Roksan
Rotel
30032
30180, 30157
30101
30003
31294, 30072, 30032
30626, 30190, 30037,
30029, 30028, 30000
31711, 31318
31317
30157
31208
30157
30179
30274, 30157, 30038
30626, 30435, 30180,
30157, 30038, 30029
31484
30157
31703, 30660, 30290,
30256
30029
30468, 30437, 30420,
30179, 30032, 30000
30083
30157
30000
30157
30098, 30083
30468, 30437, 30420,
30180, 30179, 30145,
30087, 30032, 30000
30420
30157
31208
30157
31327, 30101
31075, 30468, 30437,
30420, 30179, 30145,
30087, 30037, 30032,
30000
30752, 30388, 30303,
30029
30420
30029
30626, 30274, 30157
31087, 31062, 30468,
30032
30157
31852
30420
30157
30157
30157
30029
31075, 30468, 30437,
30420, 30180, 30179,
30032, 30000
30032, 30053, 30179,
30420, 30468, 31062
30468, 30437, 30420,
30180, 30179, 30145,
30087, 30032, 30000
30157
30435
30420, 30157
74
Appendices
Appendix C: Programming the Remote Control, continued
Programming Codes, continued
CD Players
Make
Code
A/V Receivers
Make
Code
A/V Receivers
Make
Code
Satellite Receivers
Make
Code
SAE
Sansui
Sanyo
Sears
Sharp
Sherwood
Sonic Frontiers
Sony
Amplifier
Technologies
Anam
Apex Digital
Arcam
Atlantic Technology
Audiophase
Audiotronic
Audiovox
B&K
Nakamichi
Onkyo
AlphaStar
Bell ExpressVu
Chaparral
Crossdigital
DirecTV
30157
30157, 30000
30179, 30087, 30000
30179
30180, 30037
31950, 30180
30157
31364, 30490, 30185,
30100, 30000
Soundesign 30145
Sugden
30157
Sylvania
30157
Symphonic
30180
TAG McLaren 30157
Tandy
30032
Tascam
30420
TDK
31208
Teac
30490, 30420, 30180
Technics
30029, 30303
Techwood
30303
Thule Audio 30157
Tivoli Audio
31553
Universum
30437
Victor
30072
Wards
30179, 30157, 30087,
30053, 30032
Yamaha
31292, 30490, 30036
Yorx
30000
Laser Disc Players
Make
Code
Carver
Denon
Harman/
Kardon
Magnavox
Marantz
Mitsubishi
NAD
Optimus
Panasonic
Philips
Pioneer
Polk Audio
Quasar
Sony
Technics
Theta Digital
Toshiba
Wards
Yamaha
20194, 20064
20241, 20172, 20059
20194
20241, 20217, 20194,
20064
20194, 20064
20243, 20241, 20059
20059
20059
20204
20194, 20064
20241, 20059
20194
20204
20201, 20193
20204
20194
20059
20059
20217
A/V Receivers
Make
Code
ADC
Adcom
Aiwa
Akai
Alco
AMC
30531
31617, 31616
31641, 31405, 31388,
31347, 31321, 31243,
30189, 30121
31255
31390
31077
Bel Canto
Design
BK
Bose
Brix
Cairn
Cambridge
Soundworks
Capetronic
Carver
31584
31609, 31074
31774, 31430, 31257
31189
31487
31387
31189
31627, 31390
30840, 30820, 30702,
30701
31584
30702
31933, 31253, 31229,
30639
31602
30189
31477
30531
31289, 31189, 30189,
30121
Classe
31920
Clatronic
30797
Coby
31263
Curtis
31263, 30797
Curtis Mathes 30014
Delphi
31414
Denon
31360, 31311, 31306,
31142, 30121
Electrohome 32026
Emerson
30531
Fisher
31801, 31409, 30797
Fosgate
31487
Glory Horse 31263
Goodmans
30797
GPX
31299
Grundig
31387, 30189
Harman/
31306, 31304, 31289,
Kardon
30891, 30189, 30110
Hitachi
31801, 31273
Insignia
31077, 31030
Integra
31805, 31320, 31298,
30842, 30135
JBL
31306, 30110
JVC
31811, 31643, 31495,
31374, 31282, 31263,
31058
Kawasaki
31390
Kenwood
31570, 31569, 31363,
31313
KLH
31428, 31390
Koss
31497, 31366
Linn
30189
Liquid Video 31497
Magnavox
31514, 31269, 31266,
31189, 30531, 30189
Marantz
31289, 31269, 31189,
30891, 30200, 30189
McIntosh
31289
Micromega
31189, 30189
Mitsubishi
31957, 31922, 31921,
31920, 31393
Myryad
31189
Downloaded From TV-Manual.com Manuals
31555, 31313, 30097
31805, 31320, 31298,
30842, 30135
Optimus
31074, 31023, 30849,
30797, 30670, 30531,
30121, 30014
Oritron
31497, 31366
Outlaw
31487
Panasonic
32967, 31764, 31763,
31633, 31548, 31518,
31509, 31363, 31350,
31316, 31308, 31288,
30309
Philips
31368, 31365, 31283,
31269, 31268, 31266,
31189, 30891, 30189
Pioneer
31384, 31343, 31123,
31023, 30630, 30531,
30150, 30014
Polk Audio
31414, 31289, 30189
Proceed
31922
RadioShack 31609, 31263
RCA
31609, 31511, 31390,
31123, 31074, 31023,
30531
Realistic
31609, 30121
Revox
30189
Rio
31869
Samsung
31500, 31304, 31295
Sangean
32165
Sansui
31189, 30189
Sanyo
31801
Sharp
31386, 31361
Sharper
31416, 31411, 31410,
Image
31409, 31385, 31263,
30797
Sherwood
31077
Sirius
31811, 31627, 31602
Sonic Blue
31869
Sony
31858, 31759, 31758,
31658, 31622, 31558,
31529, 31503, 31458,
31441, 31406, 31382,
31371, 31367, 31258,
31131, 31058
Soundesign 30670
Stereophonics 31023
Sunfire
31313
Sylvania
30797
Teac
31528, 31390, 31267,
31074
Technics
31633, 31518, 31308,
30309
Thorens
31189
Toshiba
31788, 31123, 30842,
30135
Venturer
31390, 30849
Wards
30189, 30014
XM
31414, 31406
Yamaha
31815, 31476, 31375,
31331, 31276, 31176,
31023, 30176
YBA
31921
Dish Network
System
Dishpro
Echostar
Expressvu
Fortec Star
Funai
GE
GOI
Goodmans
Hitachi
Houston
HTS
Hughes
Network
Systems
Humax
Innova
JVC
LG
Magnavox
Memorex
Mitsubishi
Motorola
NEC
Netsat
Optimus
Panasonic
Pansat
Paysat
Philips
Pioneer
Proscan
RadioShack
RCA
Samsung
Sanyo
SKY
Sony
Star Trak
Thomson
Tivo
Toshiba
UltimateTV
10772
11170, 10775
10216
11109
11856, 11749, 11640,
11639, 11609, 11444,
11443, 11442, 11414,
11392, 11377, 11142,
11109, 11108, 11076,
10819, 10749, 10724,
10639, 10566, 10392,
10247, 10099
11775, 11505, 11170,
11005, 10775
11775, 11505, 11005,
10775
11775, 11505, 11170,
11005, 10775
11775, 10775
11821
11377
10566, 10392
11775, 10775
11246
11250, 10819, 10749
10775
11775, 10775
11749, 11444, 11443,
11442, 11142, 10749
11790, 11781
10099
11775, 11170, 10775
11414, 11226
10724, 10722
10724
10749
10856
11270
10099
10724
10701, 10247
11807
10724
11749, 11442, 11142,
11076, 10819, 10775,
10749, 10724, 10722,
10099
11442, 11142
10566, 10392
10775, 10566
11442, 11392, 11142,
10855, 10775, 10566,
10392, 10143
11609, 11442, 11377,
11276, 11142, 11109,
11108
11219
10856, 10099
11640, 11639, 10639
10772
10566, 10392
11444, 11443, 11442,
11142
11749, 10790, 10749
11640, 11392
75
Appendices
Appendix C: Programming the Remote Control, continued
Programming Codes, continued
Satellite Receivers
Make
Code
VCRs
Make
Uniden
Zenith
DirecTV
Dual
Durabrand
Dynatech
Electrohome
VCRs
Make
A-Mark
ABS
Accurian
Admiral
Adventura
Adyson
Aiko
Aiwa
Akai
Alba
Alienware
Allegro
America
Action
American High
Amstrad
Asha
Astra
Audiovox
Avis
Beaumark
Bell & Howell
10724, 10722
11856, 11810, 10856
Code
20278, 20240, 20046,
20037, 20000
21972
20000
20479, 20209, 20104,
20060, 20048, 20047,
20039
20240, 20037, 20000
20072
20278
20124, 20037, 20000
20242, 20175, 20041
20278, 20209, 20072
21972
20039
20278
20081, 20035
20000
20240
20240, 20035
20278, 20038, 20037
20072, 20000
20240
20479, 20104, 20048,
20046, 20039, 20035,
20000
Broksonic
20479, 20209, 20184,
20121, 20002
Calix
20037
Candle
20037, 20038
Canon
20035
Capehart
20002
Carrera
20240
Carver
20035, 20081
CCE
20072, 20278
Cineral
20278
Citizen
20479, 20278, 20240,
20209, 20037, 20035,
20000
Classic
20037
Colortyme
20278, 20060, 20045,
20035
Colt
20072, 20000
Craig
20240, 20072, 20047,
20037
Criterion
20072, 20000
Crosley
20081, 20035, 20000
Crown
20278, 20072
Curtis Mathes 20432, 20278, 20240,
20162, 20060, 20041,
20035, 20000
Cybernex
20240
CyberPower
21972
Daewoo
20278, 20046, 20045,
20037
Daytron
20278, 20037
Dell
21972
Denon
20081, 20042
Derwent
20041
Code
20739
20000
20039, 20038
20240, 20000
20240, 20209, 20060,
20043, 20037, 20000
Electrophonic 20037
Emerald
20184, 20121
Emerex
20032
Emerson
21593, 20593, 20479,
20278, 20240, 20209,
20184, 20121, 20043,
20037, 20002, 20000
Fisher
20104, 20047, 20046,
20039, 20000
Fuji
20035, 20033
Fujitsu
20000
Funai
21593, 20593, 20278,
20072, 20037, 20000
Garrard
20000
Gateway
21972
GE
20240, 20060, 20048,
20035, 20000
Gemini
20060
Genexxa
20278, 20037, 20000
Go Video
20614, 20526, 20432,
20240
GoldStar
20278, 20039, 20038,
20037, 20035, 20000
Goodmans
20278, 20081, 20072,
20037, 20000
Gradiente
20000
Granada
20081, 20042
Grundig
20081
Harley David- 20000
son
Harman/
20081, 20075, 20038
Kardon
Harvard
20072
Harwood
20072
Headquarter 20046
Hewlett
21972
Packard
HI-Q
20047, 20035, 20000
Hitachi
20089, 20045, 20042,
20041, 20037, 20035,
20000
Howard Com- 21972
puters
HP
21972
Hughes
20739, 20042
Network
Systems
Humax
21988, 21797, 20739
Hush
21972
Hytek
20072, 20047, 20000
iBUYPOWER 21972
ITT Nokia
20240, 20041
Janeil
20240
Jensen
20067, 20041
JVC
21162, 20067, 20041
KEC
20278, 20037
Kenwood
20067, 20046, 20041,
20038
KLH
20072
Kodak
20037, 20035
Downloaded From TV-Manual.com Manuals
VCRs
Make
KTV
LG
Linksys
Lloyd’s
Loewe
Logik
Lumatron
Luxor
LXI
M Electronic
Magnasonic
Magnavox
Magnin
Marantz
Marta
Matsui
Matsushita
Media Center
PC
MEI
Memorex
Code
20000
21037, 20240, 20038,
20037
21972
20240, 20072, 20038,
20000
20081
20240, 20072, 20000
20278
20046
20067, 20042, 20037,
20000
20240
20593, 20278, 20240,
20072, 20037, 20000
21593, 20618, 20593,
20563, 20240, 20081,
20048, 20039, 20037,
20035, 20000
20240
20081, 20038, 20035
20037
20209, 20037
21162, 20162, 20081,
20035
21972
20035
21262, 21162, 21037,
20479, 20278, 20240,
20209, 20162, 20104,
20072, 20048, 20047,
20046, 20039, 20037,
20035, 20000
Metz
20037
MGA
20240, 20060, 20043
MGN Technol- 20240
ogy
Microsoft
21972
Midland
20240
Mind
21972
Minolta
20042
Mitsubishi
20443, 20242, 20214,
20173, 20075, 20067,
20060, 20048, 20047,
20043, 20042, 20041,
20000
Motorola
20048, 20035
Movie Walker 20072
MTC
20240, 20072, 20000
MTX
20000
Multitech
20072, 20039, 20000
NAD
20240, 20104
NEC
20104, 20067, 20041,
20038
New Tech
20072
Nikko
20278, 20037
Nikkodo
20278, 20037
Nishi
20240
Niveus Media 21972
Noblex
20240
Northgate
21972
Olympus
20162, 20104, 20035
Onkyo
20222
VCRs
Make
Optimus
Orion
Panama
Panasonic
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Polk Audio
Portland
Presidian
Profitronic
Proscan
Protec
Protech
Pulsar
Pulser
Quarter
Quartz
Quasar
RadioShack
Radix
Randex
RCA
Realistic
ReplayTV
Ricavision
Runco
Salora
Samsung
Samtron
Sanky
Sansui
Code
21262, 21162, 21062,
21048, 20593, 20432,
20240, 20162, 20104,
20048, 20047, 20037,
20035, 20000
20479, 20278, 20240,
20209, 20184, 20121,
20104, 20002, 20000
20035
21262, 21162, 21062,
20616, 20614, 20225,
20162, 20035, 20000
20240, 20162, 20081,
20067, 20047, 20042,
20038, 20037, 20035,
20000
20042
20479, 20209, 20081,
20035, 20000
21181, 21081, 20739,
20618, 20616, 20209,
20162, 20081, 20048,
20045, 20035, 20000
20037
20162, 20081, 20067,
20042
20081
20278
21593
20240
20060
20072, 20000
20072
20278, 20240, 20039
20240
20046
20047, 20046, 20035
21162, 20162, 20035,
20002
21162, 21037, 20240,
20162, 20104, 20048,
20047, 20046, 20037,
20035, 20000
20037
20037
20880, 20240, 20060,
20048, 20045, 20042,
20035, 20000
21162, 20278, 20240,
20162, 20121, 20104,
20048, 20047, 20046,
20037, 20035, 20000
20616, 20614
21972
20039
20075
20739, 20432, 20240,
20060, 20045, 20038,
20000
20240
20048, 20039
20479, 20240, 20209,
20072, 20067, 20041,
20002, 20000
76
Appendices
Appendix C: Programming the Remote Control, continued
Programming Codes, continued
VCRs
Make
Sanyo
Code
20479, 20240, 20159,
20104, 20047, 20046,
20000
Scott
20184, 20121, 20045,
20043
Sears
20209, 20162, 20104,
20072, 20067, 20060,
20048, 20047, 20046,
20045, 20043, 20042,
20041, 20039, 20037,
20035, 20033, 20000
Sharp
20848, 20048, 20047,
20032, 20000
Shintom
20240, 20072, 20039,
20000
Shogun
20240
Siemens
20037, 20104
Signature
20479, 20060, 20048,
20046, 20037, 20035,
20000
Singer
20240, 20072, 20037
Sonic Blue
20616, 20614
Sonographe
20046
Sony
21972, 21032, 20636,
20067, 20047, 20046,
20035, 20033, 20032,
20000
Soundmaster 20000
Stack 9
21972
STS
20042
SV2000
20072, 20000
SVA
20000
Sylvania
21593, 20593, 20081,
20043, 20035, 20000
Symphonic
21593, 20593, 20240,
20002, 20000
Systemax
21972
Tagar Systems 21972
Tandy
20104, 20000
Tatung
20081, 20067, 20048,
20041, 20000
Teac
20067, 20041, 20000
Technics
20162, 20037, 20035,
20000
Teknika
20037, 20035, 20000
Telecorder
20240
Telefunken
20041
Tevion
20479
Thomas
20002, 20000
Thomson
20060, 20041
Tisonic
20278
Tivo
20739, 20636, 20618
TMK
20240, 20000
TNIX
20037
Tocom
20240
Toshiba
21988, 21972, 21008,
20240, 20209, 20045,
20043, 20041, 20000
Tosonic
20278
Totevision
20240, 20037
Touch
21972
Trix
20037
Ultra
20278, 20045
Unitech
20240
Vector
20045
VCRs
Make
Vector
Research
Vextra
Victor
Video Concepts
Videomagic
Videosonic
Viewsonic
Villain
Voodoo
Wards
Code
20184, 20038
20072
20067, 20041
20242, 20045
20037
20240, 20072, 20000
21972
20000
21972
20479, 20240, 20081,
20072, 20060, 20048,
20047, 20046, 20045,
20043, 20042, 20041,
20038, 20037, 20035,
20033, 20000
Wharfedale
20593
White
20479, 20278, 20209,
Westinghouse 20072, 20000
World
20479, 20209, 20002
XR-1000
20240, 20072, 20035,
20000
Yamaha
20041, 20038
Zenith
21139, 20479, 20278,
20209, 20041, 20039,
20037, 20033, 20000
ZT Group
21972
DVD Players
Make
Code
3D LAB
Acoustic Solutions
Accurian
Adcom
Afreey
Aiwa
Akai
Alba
Alco
Allegro
Amphion
Media Works
AMW
Apex Digital
Arrgo
Aspire Digital
Audiovox
Awa
Axion
B&K
BBK
Bel Canto
Design
Blaupunkt
Blue Parade
Blue Sky
Brandt
Broksonic
Downloaded From TV-Manual.com Manuals
20539, 20503
20730
21416, 21072, 20675
21094
20698
20641
21089, 20770, 20705,
20695
20717, 20672
20790
20869
20872
20872
21061, 21056, 21020,
20794, 20755, 20717,
20672, 20533
21023
21407, 21168
21072, 21041, 20790,
20717
20730
21072
20662, 20655
21224
21571
20717
20571
20699, 20695
20651
20695
DVD Players
Make
Code
DVD Players
Make
Code
California
Audio Labs
Celestial
Centrex
Cinea
CineVision
Citizen
IRT
Jaton
JBL
JMB
JSI
JVC
20490
21020
20672
20831
20876, 20869, 20833
22116, 21587, 21277,
21003, 20695
Clairtone
20571
Coby
21351, 21177, 21165,
21107, 21086, 21077,
20852, 20778
Craig
20831
Creative
20539, 20503
Curtis Mathes 21087
CyberHome
21537, 21502, 21129,
21117, 21024, 21023,
20874, 20816
Cytron
20705
Daewoo
21242, 21234, 21172,
21169, 20869, 20833,
20784, 20770, 20705
Dansai
20770
Daytek
20872
Decca
20770
Denon
20634, 20490
Denver
20778
Desay
21407
Digitrex
20672
Disney
21270, 20675
DiViDo
20705
Dual
21085, 21068, 20675
Durabrand
21127
DVD2000
20521
Electrohome 22116, 21003
Emerson
21268, 20675, 20591
Enterprise
20591
Entivo
20539, 20503
Enzer
20770
ESA
21268
Firstline
20651
Fisher
20670
Funai
21334, 21268, 20675
Gateway
21158, 21077, 21073
GE
20815, 20717, 20522
Go Video
21730, 21304, 21158,
21144, 21099, 21075,
21044, 20869, 20833,
20783, 20744, 20741,
20717, 20715, 20573
Go Vision
21072
GoldStar
20869, 20741
Goodmans
20790
GPX
20769, 20699
Gradiente
20651, 20490
Greenhill
20717
Grundig
20705, 20539
Harman/
20702, 20582
Kardon
Hello Kitty
20831
Hitachi
20664, 20573
Hiteker
20672
iLo
21348
Initial
20717
Insignia
22095, 21268
Integra
20627, 20571
jWin
Kawasaki
Kenwood
KLH
Kloss
Konka
Koss
Lasonic
Lecson
Lenoxx
LG
LiteOn
Loewe
Logix
Magnasonic
Magnavox
Malata
Marantz
McIntosh
Medion
Memorex
Microsoft
Minato
Mintek
Mitsubishi
Momitsu
Mustek
Myryad
NAD
Naiko
Nakamichi
NEC
Nesa
NexxTech
Nintaus
Norcent
Onkyo
Oppo
Optimus
OptoMedia
Electronics
Oritron
Palsonic
Panasonic
Philco
Philips
Phonotrend
PianoDisc
Pioneer
Polaroid
20783
21078
20702
20695
21423
21164, 20867, 20623,
20558
21051, 21049
20790
20534, 20490
21149, 21020, 20790,
20717
20533
20721, 20711
21423, 21061, 20896,
20769, 20651
21173, 20798, 20627
21533
21127
20869, 20741, 20591
21440, 21416, 21158,
21058
20741, 20511
20783
20675, 20651
21506, 21268, 20675,
20646, 20539, 20503
21159, 20782
20675, 20539, 20503
21533, 21273
20651
21270, 20831, 20695
22083, 20522
20752
20839, 20717
21521, 20521
21082
20730
20894
20741
20770
21222
20869, 20785
20717
21402
21051
21265, 21107, 21003,
20872
21769, 20627, 20503
21525, 21224, 20575
20571
20896
20651
20852, 20672
21762, 21641, 20703,
20571, 20503, 20490
20675
22084, 22056, 21354,
21267, 20675, 20646,
20539, 20503
20699
21024
21571, 20631, 20571,
20525, 20142
21086, 21061, 21020
77
Appendices
Appendix C: Programming the Remote Control, continued
Programming Codes, continued
DVD Players
Make
Code
DVD Players
Make
Code
DVD Players
Make
Code
DVD Players
Make
Code
Polk Audio
Portland
Presidian
Proceed
Proscan
Prosonic
ProVision
Qwestar
Radionette
RadioShack
RCA
Samsung
Sony
Tredex
Unimax
United
Universum
Urban Concepts
US Logic
V
Venturer
Vizio
Vocopro
Wesder
Xbox
Yamaha
Realistic
Reoc
Revoy
Rio
RJTech
Rotel
Rowa
Saba
Sampo
20539
20770
21072, 20675
20672
20522
20699
20778
20651
20741
20571
21769, 20822, 20790,
20717, 20571, 20522
20571
20752
20699
20869
21360
21178, 20623
20823
20651
20752, 20698
Sansui
Sanyo
Schneider
Schwaiger
Sensory
Science
Sharp
21075, 21044, 20820,
20744, 20573, 20490,
20199
20695
21334, 20873, 20695,
20675, 20670
20783
20752
21158
21256, 20752, 20675,
20630
Sharper Image 21117
Sherwood
21077, 21043, 20770,
20633
Shinsonic
20839, 20533
Slim Art
20784
SM Electronic 20730
Sonic Blue
21099, 20869, 20783,
20715, 20573
Downloaded From TV-Manual.com Manuals
21536, 21533, 21516,
21431, 21070, 21033,
20864, 20533
Sungale
21074
SVA
21105, 20860, 20717
Sylvania
21268, 20675
Symphonic
21334, 21268, 20675
TAG McLaren 20894
Tatung
20770
Teac
20790, 20717, 20571
Technics
20703, 20490
Technika
20770
Technosonic 20730
Tevion
20651
Theta Digital 20571
Thomson
20522, 20511
Tivo
21503
Toshiba
21769, 21608,, 21515,
21503, 21154, 20695,
20573, 20539, 20503
Yamakawa
Zenith
Zeus
Zoece
20804, 20803, 20800
20770
20730
20591
20539, 20503
20839
21226, 21064
20790
21226, 21064
21360
20699
22083, 20522
20545, 20539, 20497,
20490
20872
20869, 20741, 20591,
20503
20784
21265
78
Appendices
Appendix D: NetCommand HDMI Control of CEC Devices
Many new HDMI devices have a feature called CEC
(Consumer Electronics Control) or HDMI Control.
Mitsubishi calls this feature NetCommand HDMI Control
or NetCommand for HDMI. HDMI CEC allows one
device, such as the TV, to control other devices, such
as an A/V receiver or disc player. CEC use is optional.
Each manufacturer chooses which CEC functions to
support so it is difficult to predict which devices and
features are compatible with Mitsubishi’s NetCommand
for HDMI. You may find that CEC functions for a specific
device are limited.
To use CEC, you must enable operation in all three
of the following:
• The TV’s Inputs > NetCommand HDMI Control
menu. You must turn on the TV’s NetCommand HDMI
Control in order for CEC to operate. When off, the TV
sends no control signals to CEC devices.
• The TV’s Inputs > Name menu. You can turn
on or off the TV’s control signals to individual
CEC devices. This option operates only when
NetCommand HDMI Control is enabled.
• The device setup menus. Most devices with HDMI
CEC compatibility let you turn it on or off in the device
menus, where it is typically listed as “HDMI Control.”
Connecting HDMI Devices to the TV
When setting up CEC control:
• Enable the TV’s NetCommand HDMI control as
described above. NetCommand for HDMI is off by
default.
• Connect and set up HDMI devices one at a time.
• First turn on the device and allow the poweron sequence (boot up) to complete. Stop any
playback, and then connect the HDMI cable as
described next.
1. Turn on the device and allow it to complete the
power-on sequence (boot up).
2. Connect the device to one of the TV’s HDMI inputs.
When the TV detects the connection, the Auto
Input Sensing screen will appear and provide additional instructions. You will see one of the following
screens, depending on your equipment.
•
Figure 2 (TV recognizes the CEC device).
The TV’s NetCommand HDMI Control is on and
the device’s CEC capability is on. This screen
confirms the device is CEC compatible by
showing the name provided by CEC. The screen
shown in figure 3 may display first before figure
2 appears.
Enabling or Disabling the TV’s
NetCommand HDMI Control
1. Press MENU to display the TV Main menu.
2. Highlight Inputs using
.
3. Press and then to select NetCommand HDMI
Control and open the menu shown in figure 1.
to turn NetCommand HDMI Control On
or Off; Off shuts off all NetCommand for HDMI
signals.
4. Use
Figure 1. The TV menu Inputs > NetCommand HDMI
Control lets you set HDMI control either on or off.
Downloaded From TV-Manual.com Manuals
Figure 2. TV recognizes the CEC device. The TV’s
NetCommand for HDMI is on and the connected
device’s HDMI Control is also on.
Appendices
79
Appendix D: NetCommand HDMI Control of CEC Devices, continued
•
Figure 3 (“power on the device”). One of
these conditions applies:
-
-
-
The TV’s NetCommand HDMI Control is
turned on, but HDMI control is turned off in
the menu of the new device.
Action: Enable the device’s CEC capabilities
in the device’s setup menus. Within a few
minutes you may see the screen in figure 2.
The device has not yet been detected (e.g.,
no power).
Action: Power on the device.
The device does not have CEC compatibility.
Action: Check the device’s setup menus. If
there is no HDMI control listed, the device
may not be compatible with CEC. Control
the device with its own remote control or use
the TV’s NetCommand IR control.
3. With the HDMI CEC device powered on, switch the
4.
NetCommand HDMI Control for an HDMI
A/V Receiver and Connected Devices
1. Turn on the TV’s NetCommand for HDMI feature.
2.
3.
4.
5.
Figure 3. “Power on the device.” The TV’s
NetCommand HDMI Control is on but either the
connected device’s HDMI Control is off or the device is
not CEC compatible.
•
Note:
Figure 4 (NetCommand HDMI Control is off).
The TV’s NetCommand for HDMI Control is
turned off.
Action: Follow the instructions in “Enabling or
Disabling the TV’s NetCommand HDMI Control”
on the opposite page.
You may not see the screen in figure 2 if the
HDMI device has previously been detected by
the TV. To check if CEC is enabled for the device, see the Inputs > Name menu. If you are
unable to change the device name, it indicates
CEC is enabled.
Figure 4. NetCommand HDMI Control is off.
Downloaded From TV-Manual.com Manuals
TV to the device (press the INPUT key, highlight the
device icon, press ENTER). Within a few minutes CEC
will be established. You may see the screen shown
in figure 2. If the screen does not display, ensure
HDMI control is turned on in the device’s menus.
Once CEC has been established, CEC will automatically name the device. Any name you may
have previously selected in figure 3 or figure 4 will
be changed to the new name.
6.
See “Enabling or Disabling the TV’s NetCommand
HDMI Control” on the opposite page.
Connect the A/V receiver to the TV before connecting any other device to the A/V receiver.
If you want to be able to switch between the A/V
receiver speakers and the TV speakers, also
connect the TV’s DIGITAL AUDIO OUTPUT to an
input on the A/V receiver.
Power on the TV and A/V receiver and allow both to
complete the power-on sequence (boot up).
Connect the HDMI output of the A/V receiver to the
TV’s HDMI input. The TV will automatically switch
to the input.
If the A/V receiver is HDMI CEC compatible, turn
on HDMI control in the A/V receiver (see the A/V
receiver menus). If the A/V receiver menu does not
show HDMI control, the A/V receiver may not be
compatible with CEC.
80
Appendices
TV main
panel
Resolving CEC Conflicts, Changing HDMI
Connections, Removing HDMI Devices
VCR
DVD player
HDMI
Cable
HDMI
Cable
ANT-2/AUX
ANT-1/MAIN
A/V receiver with
HDMI output
HDMI OUT
VIDEO
Y
Y/VIDEO
INPUT 1
R
R
DVI/PC INPUT
L - AUDIO - R
L
DIGITAL
AUDIO OUTPUT
INPUT 2
Pr
L - AUDIO - R
INPUT 3
Pb
Pb
Pr
L
YPbPr(480i/480p/720p/1080i)
Because each manufacturer selects which CEC functions to support, some devices can conflict with other
devices. If control conflicts arise, you can:
• Turn off CEC in the other device’s setup menu.
• Turn off TV control of an individual CEC device (see
below).
• Reset TV control of an individual CEC device (see
below).
AVR AUDIO
OUTPUT
L
R
IR NetCommand
OUTPUT/
EXTERNAL
CONTROLLER
INPUT
S-VIDEO
DIGITAL
AUDIO OUTPUT (INPUT 3)
Turning Off the TV’s HDMI Control of an Individual
CEC Device (Figure 5)
Optional
digital audio
connection
1. Press MENU on the TV remote control to enter the TV
Main menu.
RS-232C
RS-2
AUDIO: PCM STEREO
3D
D GLASSES EMITTER
VIDEO: 480i/480p/720p/1080i/1080p
2. Select the Inputs menu using the
keys.
3. Select the Inputs > Name menu using the key.
4. Highlight the device to remove using the key and
HDMI
cable
Connecting HDMI devices. The optional digital audio
connection allows you to hear audio through the A/V
receiver from devices connected to the TV only.
5.
6.
then the key.
With the device highlighted, select Control Off to
turn off the TV’s ability to control the device.
Press EXIT to clear the menus.
7. Plug in the AC power cord and power on the first
8.
9.
HDMI device, such as a disc player, cable box or
satellite receiver, and allow the device to complete
the power-on sequence (boot up). Stop playback if
the device starts playing.
Connect the device to the A/V receiver with an
HDMI cable.
Select the device’s HDMI input on the A/V receiver’s front panel controls or remote control.
• If the new device has the HDMI CEC Control
feature turned on, the TV will show a display
similar to Figure 2 and automatically name the
device.
• If the new device has the HDMI CEC Control
feature turned off or if it is not CEC compatible,
there will be no display.
Check the new device’s menu for the HDMI
Control feature and turn it on. If there is no
HDMI Control feature listed, this device may
not be compatible with HDMI CEC and you will
need to control the device manually.
10. After the present device has been connected and set
up, repeat steps 7 through 9 for the next HDMI device.
11. If desired, perform NetCommand IR Learning to
supplement CEC functions.
Downloaded From TV-Manual.com Manuals
Figure 5. Inputs > Name menu with HDMI Control for
AVR Tuner turned off
81
Appendices
Resetting HDMI Control or Removing an HDMI
Device (Figure 6)
1. Power off the device.
2. Disconnect the HDMI cable.
3. Press MENU on the TV remote control to enter the TV
Main menu.
4. Select the Inputs menu using the
keys.
5. Select the Inputs > Name menu using the key.
6. Highlight the device to reset using the key and
7.
then the key.
With the device highlighted, select Delete to reset
HDMI Control.
Press EXIT to clear the menus.
8.
9. To display the Auto Input Sensing screen, reconnect the device. You may need to power on the
device for it to be detected.
Using NetCommand HDMI Control
As an example of using NetCommand for HDMI
devices, you would press PLAY on the device itself to:
• Turn on the TV if not already on
• Switch to the device (no need to display the Input
Selection menu)
• Begin play of the device
Test your equipment with the TV’s remote control to
find out which commands are supported. See the table
below for commands that may be available, depending
on the individual device.
CEC-enabled VCR, DVD, and DVR functions that
may be available:
Record/
Playback
Menu
Navigation
Channel Tuning
CH
ENTER
—
CANCEL
(to cancel)
*
/
—
Digits 0–9, CANCEL
ENTER
Other
GUIDE
*
F1 (content)
MENU
The F1 key defaults to work like the device’s LIST key.
If you have a CEC-enabled A/V receiver, CEC-enabled
devices connected to the A/V receiver with an HDMI
cable may also be controllable. They can be selected
from the TV’s Input Selection menu.
Figure 6. Inputs > Name menu with AVR DVD deleted.
CEC-enabled A/V receiver functions that may be
available:
• Try the VOL, MUTE, and menu-navigation keys.
• To open the A/V receiver menu, follow these steps:
1. While watching TV, press AUDIO.
2. Press repeatedly until the Speakers option
displays.
3. While Speakers is still displayed, press MENU.
You can use NetCommand IR “learning” to add commands to those supported by CEC. You must first
connect and place IR emitters for the devices.
Downloaded From TV-Manual.com Manuals
82
Appendices
Appendix E: Troubleshooting
TV Reset Comparison Guide
You can resolve many common TV problems using
the reset functions described in the following table.
See also the troubleshooting suggestions later in this
appendix.
IMPORTANT
Before you change sound or picture settings: If
picture or sound settings seem wrong for a broadcast
channel (a channel from ANT 1, ANT 2, a cable box, or
satellite receiver), first check other channels from the
same input before changing settings. If most other
channels from the same input seem correct, there is
likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix
problems on individual channels also affect all other
channels on the same input.
Reset Name
When to Use
Format
When the picture
Press the FORMAT key to cycle through
shape seems incorrect, the available formats to find the best
use FORMAT to change
format for the current picture.
the shape of the
picture.
The last-used format for a signal
type is memorized for each input.
The next time the same input and
the same signal type is viewed,
the last-used format will be
recalled.
PerfectColor™
and PerfecTint™
Reset
(for the single
input currently
being watched)
When the color intensities 1.
seem out of balance,
use the PerfectColor/
PerfecTint reset to reset
the color balances to the
2.
original factory settings.
Both PerfectColor and
PerfecTint and are reset
at the same time.
3.
All PerfectColor/PerfecTint sliders
are reset to the original center
position. The PefectColor/PerfecTint
settings for other inputs remain
unchanged.
A/V Memory
Reset
(for the single
input currently
being watched)
When audio and/
or video settings for
a single input seem
incorrect, use A/V
Memory Reset to
return the input to
the original factory
settings.
A/V Reset
(for all inputs)
To reset audio and
While viewing the TV, press the
video adjustments for
control-panel touch keys GUIDE and
all inputs to the original FORMAT at the same time.
factory settings.
All Audio and Video settings are
returned to the original factory
settings, including Listen To and
Language, plus Closed Captions
settings and Format settings.
Channel
Memorization
To erase and
re-memorize channels
on ANT 1 or ANT 2.
1. While viewing the TV, press MENU
to display the Main menu.
2. Press to highlight the Setup
icon.
3. Press to highlight the Scan
icon.
4. Press to highlight the antenna
input and reception mode, e.g.
Ant 1 Air.
5. Press to highlight the Start
button icon and press ENTER to
start the memorization.
All previously memorized channels for the selected antenna
input are erased and a new
set of memorized channels is
created. All custom settings for
Fav, channel names, and channel
locks are deleted. To add or
delete individual channels, see
Edit menu instructions on page
47.
Lock Menu
Pass Code
To change your Lock
menu pass code
See the cutout page in Appendix B,
page 69.
Allows a new code to be
established.
Downloaded From TV-Manual.com Manuals
How to Use
While viewing the input to be
reset, press MENU to display the
Main menu with the A/V icon
highlighted.
Use to highlight PerfectColor
and press ENTER to display the
PerfectColor adjustment screen.
Press CANCEL to reset the colors.
1. While viewing the input to be
reset, press MENU to display the
Main menu with the A/V icon
highlighted.
2. Use to highlight the Reset
icon and press ENTER to reset.
Resulting Action
All Audio and Video settings
for the individual input are
reset except for the Listen To,
Language, audio Balance, and
Closed Caption settings.
Appendices
83
Appendix E: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
Control-Panel
Lock Release
To re-enable the
control-panel touch
keys after activation of
the Control-Panel Lock
Press and hold the MENU touch key
on the control panel for over eight
seconds. This works even if the TV
is powered off.
Allows the control panel to be
unlocked if the remote control is
misplaced.
System Reset
If the TV does not turn Press the SYSTEM RESET button on the
on or off, does not
control panel.
respond to the remote
control or controlpanel touch keys, or
has audio but no video.
The TV will turn off and the blue
LED will flash quickly for about
one minute. When the blue LED
stops flashing, you may turn on the
TV. The changes you made most
recently, before using SYSTEM RESET,
may be lost. Changes you made
previously, however, are not lost.
TV Reset
IMPORTANT:
To reset all consumeraccessible settings
and all memories to
the original factory
defaults.
The TV will start the initialization
process. The TV will then turn off
and the front blue LED will start
flashing. When the LED stops
flashing, you can turn the TV on
again. The Parental Lock Pass
code will remain unaffected, but
all other memories and settings
outlined in this Owner’s Guide
will need to be set again.
Use this reset
only if all other
resets have
been unsuccessful.
CAUTION: All ownerperformed setups
and adjustments will
be erased, including NetCommand IR
setups.
1. While viewing the TV, press MENU
to display the TV Main menu.
2. With the Main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
3. READ THE ON-SCREEN
WARNING AND INSTRUCTIONS.
• If you do not wish to use this
reset, press EXIT or MENU to
back out.
• If you do wish to use the
reset, press ENTER to erase all
memories and settings.
Service and Customer Support
Customer Support
Service
•
If you are unable to correct a problem with your
TV, consult Mitsubishi Consumer Relations at (800)
332-2119.
To order replacement or additional remote
controls or Owner’s Guides, visit our website at
www.mitsuparts.com or call (800) 553-7278.
•
For questions:
•
DO NOT adjust any controls other than those
described in this Owner’s Guide.
•
DO NOT remove the protective back cover of
your TV.
Downloaded From TV-Manual.com Manuals
Call Consumer Relations at (800) 332-2119.
E-mail: MDEAservice@mdea.com
Website: www.mitsubishi-tv.com
84
Appendices
Appendix E: Troubleshooting, continued
General TV Operation
Symptom
Remarks
1.
The TV remote control does not work.
•
•
•
•
•
•
2.
When I try to use the remote control, the
POWER key blinks five times.
Replace the batteries.
3.
TV does not respond to the remote control or
to control-panel touch keys and TV will not
power on or off.
•
•
Unplug the AC power cord for 10 seconds.
Use the System Reset button.
4.
When a device is selected from the Input Selection menu, the screen is blue or black (no signal
source).
•
•
Make sure the selected device is turned on.
Begin play of the device.
5.
You have forgotten your Lock menu pass code.
See Appendix B, “Bypassing the Parental Lock,” page 69.
6.
Rating restrictions are not working.
Open the Parental Lock menu and:
• Verify that the U.S. Ratings or Other Ratings setting is On.
• Check the Lock Time/Unlock Time to check if rating restrictions are disabled.
• Rating restrictions apply only to content on ANT 1 and ANT 2,
and VIDEO composite video jacks.
7.
On-screen displays appear each time you
change a function.
Normal TV operation.
8.
A warning message appeared on screen
stating, “TV will shut down in a few seconds.
Please check if the air flow is blocked.”
•
I have turned on CEC for my HDMI devices
but control is erratic and I wish to disable it.
•
9.
•
•
•
•
Downloaded From TV-Manual.com Manuals
Check that the batteries are fresh and installed correctly.
Check that the slide switch on the remote is set to TV.
Be no more than 20 feet from the TV when using the remote control.
Program the remote control to operate the TV or other device.
Reset the remote control.
If you have a custom home theater controller but prefer to use
the TV’s remote control, unplug the controller cable from the
TV’s IR—NetCommand® Output/External Controller Input.
Room temperature has exceeded proper levels. Cool the
room.
The TV has overheated. Clear blocked air vents and ensure
at least four inches of clearance on all sides of the TV.
Turn off all NetCommand HDMI control signals from the TV.
Open the Inputs > NetCommand HDMI Control menu and
set to Off (page 51).
Turn off the TV’s NetCommand HDMI control for the specific device. Open the Inputs > Name menu, select the
device, select Control Off (page 51).
Disable CEC on the device itself. See the device’s instructions.
If the problem persists after doing one of the above, also do
the following:
1. Disconnect the device from the TV.
2. Open the Inputs > Name menu. Highlight the device
and select Delete to remove the device from the Input
Selection menu.
3. Reconnect the device to the TV and Auto Input Sensing
will recognize the device as a non-CEC device.
Appendices
85
Appendix E: Troubleshooting, continued
TV Channels
Symptom
Remarks
1.
The TV takes several seconds to respond to
channel changes.
•
•
•
•
It is normal for digital channels to take longer to tune in.
Press ENTER after a entering channel number to avoid delays.
Use a 4-digit number for an over-the-air digital channel.
Use a 6-digit number for digital cable channels if your cable service
is able to recognize 6-digit channel numbers.
2.
You cannot access a channel.
•
•
Use number keys instead of CH / .
Be sure the channel you want to view is in memory. See Setup >
Scan on page 46.
Check that the TV is switched to the correct device or antenna for
that channel by pressing the INPUT key.
Make sure Channel Lock is off.
Make sure the Lock > Parent menu lock is set to off.
If you cannot tune to a virtual digital channel even though the TV has
already memorized digital channels, tune to the physical channel
number used by the broadcaster. The virtual channel will then be
automatically added to memory.
•
•
•
•
3.
Name options are not available for some
channels.
You can name only memorized analog channels and memorized
digital channels not named by the broadcaster.
4.
When ChannelView list is displayed, information appears incomplete
•
•
Available information is sent from the broadcaster or cable
provider. No other data is available.
Make sure the TV clock is set correctly.
TV Power On/Off
1.
Symptom
Remarks
TV takes an excessively long time to power
on.
•
•
•
•
•
When switched on, the TV needs time to boot up, just as a
computer does.
TV Energy Mode is set to Low Power. Change TV Energy
Mode to Fast Power On in the Setup menu.
2.
You cannot program the TV to turn on automatically (Timer function)
3.
The TV will not turn on after being plugged in. If light on front panel is blinking, wait at least one and a half
minutes for the light to turn off, then press POWER again.
4.
TV turned itself off and the light on the front
panel started to blink.
•
•
•
The TV may be locked.
The clock may not be set.
TV Energy Mode is set to Low Power. Change to Fast
Power On in Setup menu.
Momentary power fluctuation caused the TV to turn off to
prevent damage. Wait for the blue light to stop flashing and
turn the TV on again.
If the TV does not stay on, use the System Reset button on
the control panel. If this happens frequently, obtain an AC
line power conditioner/surge protector.
An unusual digital signal may have been received, triggering a
protection circuit. Wait for the light to stop flashing and turn TV
on.
5.
TV turned itself off and the STATUS light is
yellow.
The TV has overheated. Clear blocked air vents and ensure at
least four inches of clearance on all sides of the TV.
6.
TV will not power off.
Use the System Reset button.
Downloaded From TV-Manual.com Manuals
86
Appendices
Appendix E: Troubleshooting, continued
Picture
Symptom
Remarks
1.
Picture does not look like a high-definition
picture.
Not all signals are high-definition signals. To receive high-definition programming from your cable or satellite provider, you must
subscribe to the provider’s high-definition service. Some overthe-air broadcasts are in high-definition and can be received with
a high-quality antenna suited to your location.
2.
There is a large black or gray rectangle on
the screen.
The TV’s analog closed captioning has been set to “text” mode
in the Captions menu. Turn off because there is no text information being broadcast.
3.
You cannot view a picture when playing a
VHS tape.
Check your VCR’s owner’s guide for further troubleshooting.
4.
VCR or DVD player’s on-screen menus jitter
up and down.
Possible cause: Many VCRs and DVD players provide onscreen menus at only half-resolution. These lower-resolution
graphics may appear to jitter up and down when the TV converts them to high-definition graphics.
5.
When viewing a stopped VCR, white lines
are rolling on the screen.
•
•
•
6.
A color program appears as a black and
white image, or the colors are dim, or the
screen is black.
The PerfectColor color balance has been incorrectly set. Reset
the PerfectColor balance.
7.
Picture from an HDMI input is noisy (poor
quality).
Upgrade a Category 1 (unmarked) HDMI cable to a Category 2
high-speed HDMI cable.
Turn off video mute for the VCR.
Begin playing the tape.
Change the VCR input to the antenna input.
Sound (see also NetCommand troubleshooting for additional help with A/V receiver concerns)
1.
Symptom
Remarks
There is no sound even when the
volume is turned up.
•
•
•
•
•
Check if the MUTE key is on.
The TV’s “Listen to:” setting may be set to SAP.
Check that the Speakers option is set to TV to hear sound from the
TV speakers.
If using an A/V receiver, check that the Speakers option is set to AV
Receiver to hear sound from the A/V receiver speakers.
Perform a System Reset.
2.
The sound does not match the screen
picture.
The TV’s Listen to: setting may be set to SAP. See page 44.
3.
The sound from my A/V receiver does
not match the screen picture (I should
hear the correct audio from my A/V
receiver).
•
•
4.
The sound from my A/V receiver does
•
not match the screen picture (my source
device should be sending both audio
and video through the A/V receiver).
•
Downloaded From TV-Manual.com Manuals
Check that DIGITAL AUDIO OUTPUT and/or AVR AUDIO
OUTPUT on TV’s back panel is connected to the A/V receiver.
Without this connection, devices connected only to the TV (and
not the A/V receiver) can be heard only from the TV speakers.
Note that this includes the ANT 1/ANT 2 inputs, a device (such
as a camcorder) connected to the front panel, and any other
device sending audio to the TV only.
Check A/V receiver input selection in the Inputs > AV Receiver
menu. If NetCommand is set up incorrectly for the A/V receiver,
see “A/V Receiver Control: Automatic Audio Switching (nonHDMI A/V receiver),” page 62.
Check A/V receiver input selection in the Inputs > AV Receiver menu.
If NetCommand is set up incorrectly for the A/V receiver, see “Setup
to Control Automatic Audio and Video Switching via HDMI,” page 65.
The TV’s Listen to: setting may be set to SAP. See page 44.
Appendices
87
Appendix E: Troubleshooting, continued
Sound (see also NetCommand troubleshooting for additional help with A/V receiver concerns)
Symptom
5.
Remarks
Cannot select an audio-only device; it does Insert a video plug into any composite VIDEO jack for the Auto Input
not appear in the Input Selection Menu.
Sensing screen to appear. See “Audio-Only Device,” page 27.
NetCommand IR Control
Symptom
Remarks
1.
•
A/V Receiver Set Up for Audio-Only Switching
The A/V Receiver is not connected to any video input of
the TV. To check the A/V Receiver menu, temporarily plug
into an unused input of the TV, such as Input 3. Exit the
Auto Input Sensing screen and select Input 3 from the Input
Selection menu. Press MENU.
•
A/V Receiver Set Up for Audio and Video Switching over HDMI
Use the MENU key on the A/V receiver’s remote control.
A/V Receiver with NetCommand for HDMI.
Press INPUT to open the Input Selection menu. Highlight
the A/V receiver icon and press MENU.
Cannot see the menu from the A/V Receiver.
•
2.
NetCommand unable to learn specific device
keys.
•
•
•
•
•
3.
The A/V receiver is the selected audio source •
but there is no sound.
•
4.
There is no sound from the A/V receiver
for my DVD player or other surround sound
device even though I learned the IR code for
the A/V receiver’s DVD input or other input.
(A/V Receiver Set Up for Audio-Only Switching)
Downloaded From TV-Manual.com Manuals
A/V Device does not use IR format for remote control
signal. ITT and RF formats cannot be learned.
Room lighting may affect the signal. Have the remotes very
close (6 inches or less) to the TV during Learning.
If learning a Mitsubishi remote control, make sure slide
switch is not set to TV position.
Some, but not all, device key functions can be learned by
NetCommand. For example, POWER and PLAY may be
learned, but other functions may not.
The signal from the remote control may not be strong
enough. Insert fresh batteries and try Learning again.
A/V Receiver Set Up for Audio-Only Switching
- Check to see if the A/V Receiver power is turned on.
- With A/V receiver power turned on, redisplay the
Input Selection menu and press ENTER to allow
NetCommand to correctly select the A/V Receiver
input.
- Incorrect setup in the Inputs > AV Receiver menu.
Check the device connection assigned in the AV
Receiver menu.
A/V Receiver Set Up for Audio and Video Switching over HDMI
- Check to see if the A/V Receiver power is turned on.
- If the device is connected only to the TV (e.g., on ANT1,
ANT 2, or a front panel input), verify that the TV’s
AUDIO OUTPUT is connected to the A/V receiver.
- The A/V receiver is not switching properly because
you have not learned the inputs. See “Setting Up
NetCommand IR Control of an A/V Receiver,” page 61.
NetCommand A/V receiver setup for the DVD player or digital
surround sound device or other device is not switching properly. See chapter 6, “NetCommand IR Control,” and perform
A/V receiver setup for a digital surround sound device as
described under “A/V Receiver Control: Automatic Audio
Switching (non-HDMI A/V receiver),” page 62.
88
Appendices
Appendix E: Troubleshooting, continued
NetCommand IR Control
Symptom
Remarks
5.
There is no sound or picture from the A/V
receiver for my DVD player or other device
connected to the A/V receiver; the A/V
receiver should be sending video to the TV
over an HDMI cable. (A/V Receiver Set Up for
Audio and Video Switching over HDMI)
NetCommand A/V receiver setup is not switching audio and
video inputs properly. See “Setup to Control Automatic Audio
and Video Switching via HDMI,” page 65.
6.
I’ve selected my DVD player or other surround sound device in combination with the
TV speakers but hear no sound from the TV
speakers.
•
•
7.
A/V Receiver Set Up for Audio-Only Switching
If you have only an audio connection from the device to the
A/V receiver, a physical audio connection from the device
to the TV is also required.
- Connect the left and right audio output from the device
to the appropriate TV audio input. Now you can hear
audio from the device through either the TV speakers or
the A/V receiver.
- To switch audio sources, press AUDIO, press
to
show the Speakers option, then press to select AV
Receiver or TV.
A/V Receiver Set Up for Audio and Video Switching over HDMI
With your DVD player connected to the A/V receiver, only
video is passed from the A/V receiver to the TV because of
copy-protection restrictions on the HDMI signal
I “learned” the RECORD key for my VCR/DVR Check that the VCR or DVR is receiving a signal directly from
but when I pressed the RECORD key, the
your cable box or satellite receiver.
VCR/DVR did not record anything.
Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Blu-ray Disc is a trademark of the Blu-ray Disc Association.
FlashFX ProT is a trademark of Datalight, Inc. Datalight® is a registered trademark of Datalight, Inc. Copyright 19892008 Datalight, Inc., all rights reserved.
Manufactured under license from Dolby Laboratories. “Dolby” and “Pro Logic” are trademarks of Dolby Laboratories.
HDMI™ the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
logo and the words “Simplay™” and “Simplay HD™” are the trademarks of Silicon Image, Inc.
x.v.Color and the x.v.Color logo are trademarks of Sony Corporation.
ChannelView™, DeepField™ Imager, Easy Connect™, Laservue™, NetCommand®, PerfectColor™, Plush 1080p®,
QuickView™, SharpEdge™, Smooth120Hz™ are trademarks of Mitsubishi Digital Electronics America, Inc.
The
Downloaded From TV-Manual.com Manuals
Appendices
89
Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”).
By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws
and treaties. The Software is licensed, not sold.
1.
LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software
only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.
RIGHTS AND LIMITATIONS.
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with
any violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other
violation of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This
license is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply
with any provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are
owned by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the
Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property
laws and treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the
Software is recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved
by MDEA.
5.
EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not export
or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq,
Libya, North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the
Software back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design,
development, or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from
participating in U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA
nor any other U.S. federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL
OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR
EXPENDITURES MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT
NEITHER MDEA’S BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE
A FAILURE OF THE ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY
NOT APPLY TO YOU. MDEA’s liability to you for direct damages for any cause whatsoever and regardless of the form of the
action, will be limited to the money paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.
Downloaded From TV-Manual.com Manuals
90
Warranty
Mitsubishi LaserVue™ Television Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this
television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects
arising from improper workmanship and/or material:
a. Parts. All parts (except any software incorporated into this television and Lenticular screen surface) are warranted
for a period of one (1) year from the date of the original purchase at retail. We will repair or replace, at our option, any
defective part without charge for the part. Lenticular (i.e. front picture) screen surface is warranted against defect in
materials and workmanship for a period of thirty (30) days from the date of the original purchase at retail. Parts used
for replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used
for replacement are warranted for the remainder of the original warranty period.
b. Embedded Software. MDEA warrants that all software incorporated into this television set (the “Embedded
Software”) will perform in accordance with the functional description of Embedded Software in all material respects,
but MDEA does not warrant that the Embedded Software is error-free. MDEA also does not warrant that the
Embedded Software will be compatible under HDMI CEC software standards with products produced by any other
manufacturer. The limited warranty contained in this section shall continue for a period of one (1) year from the
date of the original purchase at retail. If, after prompt notice within the warranty period, MDEA determines that the
Embedded Software has failed to perform in accordance with such functional description in all material respects and
if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA
shall modify or replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion
may be fulfilled by means of modification or replacement software contained on a replacement memory card for
Customer installation. The foregoing shall be MDEA’s sole obligation to you under this limited warranty. All rights
under this limited warranty on the Embedded Software also subject to your acceptance of and compliance with the
terms of the Software License Agreement applicable to this television, and this limited warranty on the Embedded
Software shall be null and void if the Embedded Software is modified or changed in any manner except as specifically
authorized by MDEA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option the Lenticular
Screen if the surface proves defective. For certain items that are designed to be replaced by the consumer, including
(but not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all
other parts, we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge
for one (1) year from the original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within
the applicable warranty time period.
e. This LaserVue Television uses a single DLP chip to create the screen image. This technology creates the image
using small dots, or picture elements (pixels). Your LaserVue TV is manufactured to a high level of performance
and quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology,
sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MDEA warrants only
that the percentage of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct
customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your
MITSUBISHI dealer, by writing at the address provided below, calling MDEA at the 800-332-2119, or by using the
support feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your
television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center.
If not, you must either deliver your television to an authorized service location at your own expense, or pay for any
travel and/or transportation costs the service center may charge to and from your home. Actual service labor will be
provided without charge.
Downloaded From TV-Manual.com Manuals
Warranty
91
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service.
Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE
OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However,
please return the Owner Registration Card so that we can contact you should a question of safety arise which could
affect you.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where
such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other
than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to
carry out any maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged
by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered,
defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage
caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage
caused by electrical system or lightning. This limited warranty also excludes service calls where no defect in the
product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or
signal unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or
any other damages arising from product installation, removal from or re-installation into custom installations or on
wall mountings, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning,
sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external audio
receiver, antenna, cable or satellite systems, or service of products purchased or serviced outside the U.S.A. Please
consult the operating instructions contained in the Owner’s Guide furnished with the product for information regarding
user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of
incidental, special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
Downloaded From TV-Manual.com Manuals
92
Index
Index
A
Adjust Keys (Up/Down/Left/Right)
31, 39
Anamorphic Picture Format 35
Antenna
Connecting 25
Signal Strength for Digital Channels 33
Antenna Inputs (ANT 1, ANT 2) 12
Audio Lock (A/V receiver control) 72
Audio Output Jacks 13
Auto Input Sensing 16
Auto-Off (Sleep Timer) 30
Auto-On (Timer) 49
A/V Memory Reset 82
A/V Receiver
and TV Speakers 44
and TV’s Remote Control 61, 65,
71
Audio Lock 72
Connecting 13, 28
Controlling Sound Volume 18
Disconnecting Analog 18
NetCommand IR Control 55, 59,
61
Controlling a Device Connected
to the A/V Receiver 19, 66
Video and Audio Switching via
HDMI 65
A/V Reset 10, 82
B
Back Panel. See Main Panel (on back
of TV)
Batteries 14
Blue Glow 41
Brightness (picture adjustment) 42
C
Cable Box
and TV’s Remote Control 32, 71
Connecting 23, 24, 26, 27
Cable Management 22
Camcorder 29
Captions Menu 45
CEC (Consumer Electronics Control)
10, 19, 71
A/V Receiver 18, 79, 87
CEC-Enabled Devices and the
Inputs Name menu 51
Disabling CEC for a Device 51
NetCommand for HDMI/CEC 78
Troubleshooting 84
Channels
Add Single Channel to Memory
46, 47
antennaweb.org 46
Downloaded From TV-Manual.com Manuals
Changing Channels 30
Channel Lock 47
Digital Channel Numbers 68
Edit Channels (menu) 47
Favorites (Fav) 34, 47
Memorizing (scanning) 16, 46
Naming 47
Physical/Virtual Channel Numbers 46, 47
Scan (memorize) 46
Status Display 33
Troubleshooting 85
ChannelView Channel Listings 32
Cleaning 8
Clock, Set Date and Time 48
Closed Captions 45
Color Adjustments 40, 42, 43
Reset Color 40, 82
Computer
and Display Formats 21, 68
Connecting 20
Contrast 42
Controller Output 13
Control Panel 10
Control Panel Lock 54
Customer Service and Support 83
D
Date. See Clock
Defaults, Resetting 82
DIGITAL AUDIO OUT 13
Dolby Digital 13, 28, 62, 68
DVD Player
and TV’s Remote Control 32, 71
Connecting 23, 24
DVI Device, Connecting 24
E
Edit Menu (channels) 47
Energy Mode 50
F
F1–F4 Keys 31, 57
Fan Noise 7
Fast Power On 50
FAV (Favorite Channels) 34, 47
Film Mode 41
Font (digital closed captions) 45
FORMAT Key 35
Freeze Picture 32
Front Panel
Blue Glow 41
Controls 10
Front-Panel Indicators (lights) 11
G
Game
3D Video 38
Game as Input Name 51
Game Picture Mode 42
HDMI Cables for Games 13
Global Menu 41
GUIDE Key 31, 71
ChannelView 32
H
HD (High-Definition) Signal) 35
HDMI
Changing Out an HDMI Device
and Auto Input Sensing 18
Connecting an HDMI Device 23
A/V Receiver 28
HDMI Cable Categories 13
HDMI Jack 12
NetCommand for HDMI Devices
10, 71, 81, 87
Removing an HDMI Device from
the Input Selection Menu 51
I
INFO Key
ChannelView 32
in TV Menus 39
Status Display 33
USB Photo Menu 36
Input Selection Menu
Choose Viewing Source 30
Disconnected HDMI Device 18,
51, 81
Icon Order 51
INPUT Key 31
Inputs Menu 51
Inputs > Name Menu and CEC
Devices 80
IR (infrared) Emitter Placement
56
J
JPEG Photo Files 36
L
Language
in Digital Programs 44
SAP (Second Audio Program) 44
Language Menu 46
Laser Safety 5
Learn 51. See also NetCommand IR
Control
Learn Menu 51
Letter Box Image Display 35
Level Sound 44
Light, Decorative 41
Listen To 44
Listings 32
Index
Lock TV
Bypassing the Lock 69
Lock by Channel 47
Lock by Ratings 53
Lock by Time 54
Lock Control Panel 54
Preset V-Chip Blocking 52
Low Power (Energy Mode) 50
Wired IR option 13
M
Main Panel (on back of TV) 12, 13
Media Setup Menu 37
Memorizing Channels 16, 46
Memory Reset, A/V 82
Moving the TV 7
Mute
Closed Captions 45
MUTE key 31
Video Mute 41
N
Name (Inputs > Name menu) 51
NetCommand for HDMI Devices 10,
71, 78, 81
NetCommand IR Control
About 55
A/V Receiver Control 61
Compared to Programming the
Remote Control 71
Initial Setup for Most Devices 57
Operating 59, 60
Specialized Device Keys 58
Troubleshooting 87
Noise, Video 42
O
120 Hz Picture Processing 41
Order Menu (Inputs > Order) 51
P
Parent Menu 53
Pass Code
Resetting 69
Setting 52
PAUSE Key 32
PerfectColor 40
PerfectTint 40
Photo Viewing 37
Physical Channel Number 47
Picture
AV Menu Controls 40
Picture Quality and Film Mode
41
Troubleshooting 86
Picture Mode 42
Power Consumption
Energy Mode 50
Specifications 68
Downloaded From TV-Manual.com Manuals
POWER Indicator (front panel) 11
Power On/Off
Troubleshooting 85
S-Video
Connecting 24, 26
System Reset 10, 83
Q
T
QV Key (QuickView™) 31
and FAV Key 34
Test Picture 41
3D GLASSES EMITTER Jack 13
3D Video 38, 50
Time. See Clock
Timer (auto-on) 11, 49
Time Zone. See Clock
Transportation Screws 7
Troubleshooting 82
R
Ratings (TV and Movie) 53
Set Viewing Restrictions 52
Remote Control
Keys and Functions 31, 32
Programming Codes (reference
chart) 73
Programming, Compared to
NetCommand “Learning” 71
Programming Instructions 72
Reset 32
Reset
AV Menu Reset (by input) 40
A/V Reset (all settings) 10
Color 82
Pass Code 69
Remote Control 32
Remote Control Audio Lock 72
System Reset 10
TV Reset Comparison Guide 82
S
Safety Instructions 4, 5
SAP (second audio program) 44
Satellite Receiver
and the Remote Control 71
Connecting 23, 24
Scan (memorize channels) 46
Screen Saver 41
SD (Standard-Definition Signal) 35
Setup Menu 46
Signal Definitions 35
Signal Strength Indicator 33
Sleep Timer 30
Smooth 120Hz 41
Sound
Audio Menu 44
Controlling A/V Receiver Volume
18, 61, 65
Level Sound 44
Sound Mode (audio effects) 44
Speakers Option
In Audio Menu 44
Specifications, TV 68
Standard-Definition Signal 35
Stand Part Number 7
Status Display 33
STATUS Indicator 11
Stereo System. See A/V Receiver
Surround Sound 13, 28, 63, 64
Simulated Surround Sound 44
93
V
V-Chip Ratings
Applying Restrictions 52
Definitions 53
In Status Display 33
VCR
Connecting 26
Troubleshooting 86
Vert Adjustment 43
Video from a Digital Camera 37
Video Game. See Game
Video Menu 42
Video Mute 41
Video Noise 42
Viewing Device. See Input Selection
Menu
Virtual Channel 47
W
Wall Outlet Cable 25
X
x.v.Color 13, 23, 42
Website:
www.mitsubishi-tv.com
E-mail:
MDEAservice@mdea.com
For questions, call Consumer Relations at
800-332-2119
To order replacement or additional
remote controls or Owner’s Guides
Visit our website www.mitsuparts.com
or call
800-553-7278
SYSTEM RESET
If the TV does not respond to the remote control,
control-panel touch keys, or will not power on/off,
press the SYSTEM RESET button on the control panel.
The blue LED will flash quickly for about one minute.
When the blue LED stops flashing, you may turn on
the TV. Settings changes you made most recently,
before using SYSTEM RESET, may be lost.
Downloaded From TV-Manual.com Manuals
V40
Downloaded From TV-Manual.com Manuals
For information on System Reset, please see inside back cover.
Guidelines for setting up and using your widescreen TV start on page 14.
© 2008 Mitsubishi Digital Electronics America, Inc.
853B620A10
Downloaded From TV-Manual.com Manuals