Craftsman 315.216260 Owner`s manual

Add to my manuals
26 Pages

advertisement

Craftsman 315.216260 Owner`s manual | Manualzz

Owner's Manual

II:RRFTSMRNI

16 in, variable speed

SCROLL SAW

Model No.

315.216260

Save this manual for future reference.

CAUTION: Read and follow all Safety Rules and

Operating Instructionsbefore first use of this product.

Customer Help Line

1-800-932-3188

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

VisLt the Craftsman web page: www.sears,com/craftsrnan

97200O-549

7-98

Safety

• Features

Adjustments

Operation

Maintenance

Parts List

®

NRTL/C

Table of Contents ...........................................................................................................................................

2

Warranty and Introduction..............................................................................................................................

Rules For Safe Operation .........................................................................................................................

Electrical ..........................................................................................................................................................

2

3 - 5

6

Glossary and Product Specifications .............................................................................................................

Unpacking and Tools Needed ........................................................................................................................

• Labels .............................................................................................................................................................

Features ..................................................................................................................................................

7

10-11

8

9

Assembly .................................................................................................................................................

Adjustments .............................................................................................................................................

Operation .................................................................................................................................................

Maintenance ............................................................................................................................................

Troubleshooting............................................................................................................................................

Exploded View and Repair Parts List ......................................................................................................

f

Parts Ordering / Service ...............................................................................................................................

11-12

12-15

16-19

19-20

20

22-25

26

FULL ONE YEAR WARRANTY ON CRAFTSMAN SCROLL SAW

If this rRRFTSMRN" Scroll Saw fails due to a defect in material or workmanship within one year from the date of

purchase, Sears will repair it, free of charge.

Contact a Sears Service Center for repair.

If this product is used for commercial or rental purposes, this warranty applies only for 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

Your saw has many features for making cutting

operations more pleasant and enjoyable. Safety, performance and dependability have been given top priority in the design of this saw making it easy to maintain and operate.

_.

_I, CAUTION: Carefully read through this entire owner's manual before using your new saw. Pay

close attention to the Rules For Safe Operation, and all Safety Alert Symbols including Danger,

Warning and Caution. If you use your saw

properly and only for what it is intended, you will

enjoy years of safe, reliable service.

Look for this symbol to point out important safety precautions.

It means attention!H

Your safety is involved.

_IL WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear

safety goggles or safety glasses with side shields and a full face shield when needed. We

recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears Retail Stores.

2

Thepurposeof safetysymbols

Is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.

SYMBOL

A

MEANING

SAFETY ALERT SYMBOL:

Indicates danger, warning or caution. May be used in conjunctionwith other symbols or picto- graphs.

A

DANGER: Failure to obey a safety waming will result in serious injury to yourself or to others.

Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

,a,

WARNING: Failure to obey a safety warning can result in serious injuryto yourself or to others.

Always follow the safety precautionsto reduce the risk of fire, electric shock and personal injury.

&

Note:

CAUTION: Failure to obey a safety warning may result in property damage or personal injuryto

yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. r

Advises you of information or instructionsvital to the operation or maintenance of the equipment.

IMPORTANT

Servicing requires extreme care and knowledge of the system and should be performed only by a qualified

service technician. For service we suggest you return the tool to your nearest Sears store for repair. Always use

original factory replacement parts when servicing.

_lb

,_

WARNING:

WARNING:

Do not attempt to operate this tool

until you have read thoroughly and understand

completely all instructions, safety rules, etc.

contained in this manual. Failure to comply can

result in accidents involvingfire, electric shock,

or serious personal injury. Save 6wner's manual

and review frequently for continuing safe operation, and instructingothers who may use

this tool.

power source until you have assembled and adjusted the saw as described in this manual and have read and understood all precautions and operating instructionsin the manual and printed on the tool.

READ

ALL

Do not connect your scroll saw to a

INSTRUCTIONS

KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the saw's applications and limitations as well as the specific potential hazards related to this tool.

GUARD AGAINST ELECTRICAL SHOCK BY

PREVENTING BODY CONTACT WITH

GROUNDED SURFACES. For example; pipes, radiators, ranges, refrigerator enclosures.

KEEP GUARDS IN PLACE and in good working order.

REMOVE ADJUSTING KEYS AND

WRENCHES. Get in the habit of checking to see

that hex keys and adjusting wrenches are removed from tool before turning on the saw.

KEEP THE WORK AREA CLEAN. Cluttered work areas and work benches invite accidents.

DO NOT leave tools or pieces of wood on the saw while it is in operation.

DO NOT USE IN DANGEROUS ENVIRON-

MENTS. Do not use power tools near gasoline or other flammable liquids, in damp or wet locations, or expose them to rain. Keep the work area well lit.

KEEP CHILDREN AND VISITORS AWAY. All visitors should wear safety glasses and be kept s

safe distance from work area. Do not let visitors contact tool or extension cord while operating.

MAKE WORKSHOP CHILD-PROOF with padlocks and master switches or by removing starter keys,

DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.

USE THE RIGHT TOOL. Do not force the tool or attachment to do a job it was not designed for.

Don't use it for a purpose not intended,

3

RULES FOR SAFE OPERATION (Continued) m U_E THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in'loss of power and overheating. A wire gage size (A.W.G.) of at

least 18 is recommended for an extension cord

25 feet or less in length. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

INSPECT EXTENSION CORDS PERIODI-

CALLY and replace if damaged.

DRESS PROPERLY. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry. They can get caught and draw you into

moving parts. Rubber gloves and nonslip foot-

wear are recommended. Also wear protective hair covering to contain long hair.

ALWAYS WEAR SAFETY GLASSES WITH

SIDE SHIELDS. Everyday eyeglasses have only impact-resistant lenses; they are NOT safety glasses.

PROTECT YOUR LUNGS. Wear a face or dust

mask if the cutting operation is dusty.

m

PROTECT YOUR HEARING. Wear hearing

protection during extended periods of operation.

SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your

hand and it frees both hands to operate tool.

DO NOT OVERREACH. Keep proper footing and

balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructionsfor lubricating and changing accessories.

DISCONNECT ALL TOOLS. When not in use, before servicing, or when changing attachments,

blades, bits, cutters, etc., all tools should be

disconnected from power supply.

AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in.

USE RECOMMENDED ACCESSORIES. The

use of improper accessories may cause risk of injury.

NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the blade is unintentionally contacted.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it m will operate properly and perform its intended function. Check for alignment of moving parts, bindingof moving parts, breakage of parts, saw

stability,mounting and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or

replaced by a qualified service technician at a

Sears store to avoid risk of personal injury.

DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

NEVER LEAVE TOOL RUNNING UNAT-

TENDED. TURN THE POWER OFF. Do not leave tool until it comes to a complete stop.

USE ONLY CORRECT BLADES. Use the right

blade size, style and cutting speed for the

material and the type of cut. Blade teeth should point down toward the table. Sharp blades minimize stalling and kickback. Correctly adjust blade tension.

TO PROTECT THE OPERATOR and minimize blade breakage, ALWAYS adjust the hold down foot to just clear the workpiece. Never operate the saw with any guard or cover removed. Make

sure all guards are operating properly before each use.

KEEP HANDS AWAY FROM CUTTING AREA.

Do not hand hold pieces so small that your fingers go under the blade guard. Never reach underneath work or behind, under, or within three inches of the blade and its cutting path with

your hands and fingers for any reason. Do not attempt to remove cut material when blade is moving.

,_k WARNING: Blades coast after turn off.

AVOID PINCHING THE BLADE. Be cautious when cutting off material which is irregular in cross section. For example, molding must lay flat on the table and not be permitted to rock.

DO NOT ABUSE CORD. Never yank cord to disconnect it from receptacle. Keep cord from heat, oil, and sharp edges.

INSPECT TOOL CORDS PERIODICALLY and if damaged, have repaired by a qualified service technician at a Sears store. Stay constantly aware of cord location and keep it well away from the rotating blade.

DO NOT USE TOOL IF SWITCH DOES NOT

TURN IT ON AND OFF. Have defective switches replaced by a qualified service technician at a

Sears store.

RULES FOR SAFE OPERATION

(Continued)

KEEP TOOL DRY, CLEAN, AND FREE FROM

OIL AND GREASE.

Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool

A LARGE PIECE OF MATERIAL SHOULD BE

SUPPORTED while cutting. To minimize risk of blade pinching and kickback, always support

long workpieces. Saw may slip, walk or slide while cutting long or heavy boards.

BEFORE MAKING A CUT, BE SURE ALL

ADJUSTMENTS ARE SECURE.

BEFORE CHANGING THE SETUP, REMOVING

COVERS, GUARDS OR BLADE, UNPLUG THE

SAW, AND REMOVE THE SWITCH KEY.

DO NOT FEED THE MATERIAL TOO QUICKLY while cutting. Do not force the workpiece against the blade.

NEVER CUT MORE THAN ONE WORKPIECE

AT A TIME. If making a stacked cut, all of the pieces must be secured to each other with masking tape or double stick tape to make one workpiece. Do not put more than one workpiece

on the saw table at a time. Always hold the work firmly against the table. See page 18.

AVOID CU'I-FING NAILS. Inspect for and

remove all nails from lumber before cutting.

NEVER PERFORM LAYOUT, ASSEMBLY, OR

SETUP WORK ON THE TABLE while the cutting tool is operating.

NEVER TOUCH BLADE or other moving parts during use,

NEVER START A TOOL WHEN THE BLADE IS

IN CONTACT WITH THE WORKPIECE. Clear the table of debris before turning your scroll saw on,

ALLOW THE MOTOR TO COME UP TO FULL

SPEED before starting a cut.

FIRMLY CLAMP OR BOLT your scroll saw to a firm, level workbench or table. The most comfortable saw table height is at approximately hip height.

AVOID AWKWARD OPERATIONS A_D HAND

POSITIONS where a sudden slip could cause your hand to move into the blade. ALWAYS

make sure you have good balance. Do not cut pieces of material that are too small to hold comfortably in your hand.

REPLACEMENT PARTS. All repairs, whether electrical or mechanical, should be made by qualified service technician at a Sears store or repair center.

_1= WARNING: When servicing use only identical

Craftsman replacement parts. Use of any other

parts may create a hazard or cause product damage.

NEVER USE IN AN EXPLOSIVE ATMO-

SPHERE.

Normal sparking of the motor could

ignite fumes.

DO NOT OPERATE THIS TOOL WHILE UN-

DER THE INFLUENCE OF DRUGS, ALCOHOL,

OR ANY MEDICATION.

STAY ALERT AND EXERCISE CONTROL.

Watch what you are doing and use common sense. Do not operate tool when you are tired.

Do not rush.

MAKE SURE THE WORK AREA HAS AMPLE

LIGHTING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work using your saw.

ALWAYS TURN OFF SAW before disconnecting it, to avoid accidental starting when reconnecting

to power supply. NEVER leave the scroll saw unattended while connected to a power source.

_.

WARNING: Do not allow familiarity with your saw make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.

SAVE THESE INSTRUCTIONS.

Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also.

SAVE THESE INSTRUCTIONS

5

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept

the tool's plug. When using a power tool at a consider-

able distance from the power source, use an exten- sion cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used.

Length of Extension Cord

Up to 25 feet

26-100 feet

Wire Size (A.W.G.)

18

16

When working with the tool outdoors, use an exten- sion cord that is designed for outside use. This is indicated by the letters WA on the cord's jacket.

Before using an extension cord, inspect it for loose or exposed wires and cut or worn insulation.

_i, CAUTION: Keep the cord away from the cutting area and position the cord so that it will not be caught on lumber, tools, or other objects during cutting.

ELECTRICAL CONNECTION

Your Sears Craftsman Scroll Saw is powered by a precision built electric motor. It should be connected to a power supply that Is 120 volts, 60 Hz, AC only

(normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will

cause a loss of power and the motor will overheat. If

the saw does not operate when plugged into an outlet, double check the power supply.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is

equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is propedy installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.

Repair"or replace a damaged or worn cord immediately.

"This tool is intended for use on a circuit that has an outlet like the one shown in Figure 1. It also has a grounding pin like the one shown.

GROUNDING

PIN COVEROF GROUNDED

OUTLETBOX

Fig. 1

6

Bevel Cut

A cutting operation made with the table at any angle other than 90" to the blade.

Crosscut

A cutting or shaping operation made across the grain of the workpiece.

Compound Cut

A compound cut is a cut made using a miter angle and a bevel angle at the same time.

Freehand (for scroll saw)

Performing a cut without the workpiece properly supported on the table.

Gum

A sticky, sap based residue from wood products.

Kerr

The matedal removed by the blade in a through cut or the slot produced by the blade in a nonthrough or partial cut.

Leading End

The end of the workpiece pushed into the cutting tool fimt.

Miter Cut

A cutting operation made with the saw table at an_ angle other than 90" to the blade.

Nonferrous Metal

Metal that does not contain iron; such as aluminum, brass, and copper.

Push Stick

A device used to feed the workpiece through the saw

blade during narrow ripping type operations and helps keep the operator's hands well away from the blade.

Resaw

A cutting operation to reduce the thickness of the workpiece to make thinner pieces.

Resin

A sticky, sap base substance that has hardened.

Ripping

A cutting operation along the length of the workpiece.

Saw Blade Path

The area directly in line -- over, under, behind, or in front of the blade. AS it applies to the workpiece, that area which will be, or has been, cut by the blade.

Set

The distance that the tip of the saw blade tooth is bent

(or set) outward from the face of the blade.

SPM

Strokes per minute. Used in reference to blade movement.

Throw-Back

Throwing of a workpiece in a manner similar to a kickback. Usually associated with a cause other than

the kerr closing, such as a workpiece not being

against the fence, being dropped into the blade, or being placed inadvertently in contact with the blade.

Through Sawing

Any cutting operation where the blade extends completely through the thickness of the workpiece.

Workpiece

The item on which the cutting operation is being done.

The surfaces of a workpiece are commonly referred to as faces, ends, and edges.

Worktable

The surface on which the workpiece rests while performing a cutting or sanding operation.

Throat

Motor

Drive

Blade Length

Table Size

16 in.

120 V, 1.2 amp 60 HZ-AC only

Variable Speed

500-1700 Strokes per minute

5 in. plain or pin

10-1/4 in. x 12 in.

Table Tilt

Overall Dimensions

Net Weight

47" right and 12" left

12in. W

24-1/2 in. L

14in. H

27.5 lb.

7

,_ WARNING: To prevent accidental starting or electrical shock that could cause possible serious personal injury, assemble all parts to your saw before connecting it to power supply.

Saw should never be connected to power supply when you are assembling parts, making adjustments, lubricating, installingor removing blades, cleaning, or when not in use.

Carefully lift saw from the carton and place it on a level work surface.

Remove pack of 4 extra blades and owner's manual from the carton.

_, WARNING: If any parts are missing, do not

operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury.

Do not discard the packing materials until you have carefully inspected the saw, identified all pads, and satisfactorily operated your new saw.

Note: If any parts are damaged or missing, do not attempt to plug in the power cord and turn the switch on until the damaged or missing parts are obtained and are installed correctly.

Your scroll saw comes completely assembled. A package of 4 extra blades and an owner's manual are

included with your saw.

The following tools (not included) are needed for

adjustments and alignment:

Small Combination Square

Adjustable wrench

Flatblade Screwdriver

SMALL

COMBINA_ON

SQUARE

FLATBLADESCREWDRIVER

Fig. 2

The following labels are on the scroll saw with locations indicated.

WARNING

ADVERTENCIA

ON OFF

I I:RRFTSMAN1

Customer Help Line 1-800-932-3188

WARNING I ADVERTENCIA

Fig. 3

Thisversatile

for

making toys, puzzles, games, artwork, and jewelry. It is a handy do-it-yourself tool. It cuts wood, wood

composition products, plastic, and other fibrous material up to 2 inches thick. It also cuts nonferrous metals (aluminum, brass, copper).

KNOW YOUR SCROLL SAW

Before attempting to use your saw, familiarize yourself with all operating features and safety requirements of

your Sears Craftsman scroll saw. See Figure 5.

ON/OFF KNOB WITH VARIABLE SPEED

Your scroll saw has an easy access ON/OFF knob with variable speed. Pull the knob out to turn ON the saw, and push the knob in to turn OFF the saw. Turn

the knob to adjust the speed from the high speed of approximately 1700 SPM (Strokes Per Minute) to the

low speed of approximately 500 SPM.

LOCK OFF POST

Place a pad lock in the lock post next to the ON/OFF knob to look the saw in the OFF position to prevent , unauthorized use of the saw by children or others.

TOOLLESS BLADE HOLDERS

Retain and position the blade without the use of

additional tools. Use the knobs for plain end blades or

use the designed slots for pin type blades.

TENSION

ADJUSTING

KNOB

QUICKRELEASE

KNOB

Fig. 4

BLADE STORAGE DRAWER

Attached under the left side of the table is a blade storage drawer. It will hold up to 20 blades. Drawer snaps closed securely. See Figure 4.

BLADE TENSION KNOBS

Blade tension is controlled by a dual knob tension control system. The inner (smaller) knob, tension adjusting knob, is for making adjustments of the blade tension. The outer (larger) knob, quick release knob, is used to quickly set and release blade tension to facilitate blade changes,

AIRDIAPHRAGM

HOLDDOWNFOOTLOCKKNOB

BLADE

DRAWER

PLAINENDBLADEKNOB

HOLDDOWNFOOT/

GUARD

SAWBLADE

SAWTABLE

MITERSCALE

MOTOR

LOCKOFF POS'I'

ON/OFFKNOB

Fig. 5

10

HOLD DOWN FOOT/BLADE GUARD

The hold down foot should be lowered until it just

rests on top of the workpiece to prevent the workpiece

from lifting while cutting, but not so much that the workpiece drags.

The vertical portion provides a blade guard to prevent accidental blade contact.

HOLD DOWN FOOT LOCK KNOB

Allows you to raise or lower the hold down foot/blade guard and secure it at desired heights•

SAWDUST BLOWER

Keeps the line of cut on workpiece clean for more accurate scroll cuts.

SAWDUST EXHAUST

Your saw has a sawdust exhaust that fits a standard

shop vacuum hose. See Figure 13.

SAW TABLE

Your scroll saw has an aluminum saw table that provides a working surface to support your workpiece.

TABLE LOCK KNOB

Allows you to tilt the table and lock it at the desired angle up to 45 degrees.

BEVEL SCALE

The bevel scale and indicator are located on the front

of the saw for easy viewing. They show the angle of the table•

ZERO DEGREE STOP FOR TABLE

Located under the front of the saw table, the zero

degree stop allows easy return and fine adjustment of the zero degree relationship between the table and the blade.

Your Craftsman 16 in. scroll saw was fully assembled

at the factory. Before operating this tool, it is important to check all alignments and settings. Normal handling during shipment may have changed settings.

_L WARNING: To avoid serious personal injury from unexpected tool movement, always securely mount scroll saw to a workbench.

MOUNTING

WORKBENCH

See Figure 6.

SCROLL SAW TO

If the scroll saw is to be used in a permanent applica-

tion, we recommend that you secure it in a permanent location such as a workbench. When mounting the

saw to a workbench, holes should be drilled through the supporting surface of the workbench using dimensions illustrated.

Each hole in the base of the saw should be bolted securely using 3/8 in. diameter machine

bolts, lock washers, and hex nuts (not included).

Bolt length should be 1-1/4 in. plus the thickness of the bench top.

Locate and mark the holes where scroll saw is to be mounted.

• Drill(3)7/16in.

diameterholesthrough workbench.

Place scroll saw on workbench aligning holes in the base with holes drilled in the workbench.

Insert all three 3/8 in. bolts and tighten securely

with lock washers and hex nuts.

Note: All bolts should be inserted from the top. Install

the lock washers and hex nuts from the underside of the bench.

Supporting surface where scroll saw is mounted

should be examined carefully after mounting to insure that no movement during use can result. If any tipping or walking is noted, secure workbench or supporting surface before beginning cutting operations.

II

24 in.

7/16In. dia.

6 In.

19 1116 In.

.I

T'

Fig. 6

11

CLAMPING

WORKBENCH

SCROLLSAW TO

See Figure 7.

tf the scroll saw is to be used in a portable application, we recommend that you fasten it permanently to a mounting beard that can easily be clamped to a workbench or other supporting surface. The mounting board should be of sufficient size to avoid tipping of saw while in use.

Mount saw to board using holes in frame as a template for hole pattern or the diagram in

Figure 6. Locate and mark the holes where scroll saw is to be mounted.

• Follow last three steps in previous section called

• ounUng Scroll Saw to Workbench.

Make sure mounting bolts are long enough to go

through holes in the saw frame, material being mounted to, lock washers, and hex nuts.

Note: It may be necessary to countersink hex nuts

and washers on bettom side of mounting board.

\

C-CLAMP

C-CLAMP

WORKBENCH

MOUNTING

BOARD

Fig. 7

AIRDIAPHRAGM

HOLDDOWNFOOT

KNOB

BLADE

,_k WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the sew and unplug before making any adjustments.

HOLD DOWN FOOT/BLADE

See Figure 8.

GUARD

The hold down should be adjusted so it contacts the top surface of the work being cut. Tighten adjusting knob after adjustment has been made.

• Loosen the hold down foot lock knob.

Move the hold down foot to the desired position.

Tighten the hold down foot lock knob.

The tall, front part of the hold down foot acts as a blade guard to prevent accidental contact with the blade.

SAWDUST

See Figure 8.

BLOWER

The dust blower is designed and preset to direct air to the most effective point on the cutting line. Be sure hold down foot is properly adjusted to properly secure workpiece and to properly direct air to the cutting surface.

• Insert hose to air diaphragm before starting the saw.

12

Fig. 8

SQUARING TABLE TO

THE BLADE

See Figures 9 and 10.

Loosen the hold down foot lock knob and move hold down rod all the way up. Tighten knob.

Loosen the table lock knob and move the table until it is approximately perpendicular, or st right angle to the blade.

Place a small square on the table next to the blade to check if the table is 90 degrees to the blade. If adjustment is needed, raise or lower the table until table is approximately 90 degrees to the blade and securely tighten the table lock knob.

Loosen the screw holding the scale indicator, move indicator to the 0 degree mark and securely tighten screw. Remember, the bevel scale

is a convenient guide but should not be relied

upon for precision. Make practice cuts on scrap

material to determine if your angle settings are correct.

Adjust the hold down foot to desired position and i

securely tighten the hold down foot knob.

HOLDDOWNROD

HOLDDOWNFOOT

LOCKKNOB

SETTING THE TABLE FOR HORIZONTAL

OR BEVEL CUTTING

See Figures 10, 11 and 12.

A bevel scale is provided under the work table as a

convenient guide for setting the approximate table

angle for bevel cutting. When greater precision is required, make practice cuts on scrap material and adjust the table as necessary for your requirements.

An adjustable zero degree stop is provided to quickly

return the table to the zero degree setting.

• Loosen the table lock knob and push down on

the right side of the table. If the table stops at O',

the zero degree stop is properly set. If the table stops somewhere other than zero, then adjust the zero degree stop.

ZERO I

"__ SCALE

HOLDDOWN

F00T/

\

. SAWBLADE

TABLELOCK

KNOB

SCREW

Fig. 10

• To access the zero degree stop, loosen the table

look knob, and tilt the table with the dght side all

the way down. Just under the front of the saw table is the zero degree stop. See Figure 11.

Loosen the hex nut and rotate the hex bolt to raise or lower the bolt as needed to adjust the zero degree stop. Be sure to check to see that the table is square to the blade.

Now, by returningthe table to the zero position, the

zero degree stop provides a quick reference to the preset position.

TABLELOCK

KNOB

Fig. 9

13

SAWTABLE

Fig.

11

The zero stop assembly can be rotated to the left and down out of the way and the table can be angled up to

12" to the left. See Figure 12.

Note: Make sure the zero degree stop is rotated all the way down or it will contact the blade storage drawer as you angle to the left.

Fig. 12

INSTALLING BLADES

Scroll saw blades wear out quickly and must be

replaced frequently for best cutting results. Expect to break some blades while you learn to use and adjust

your saw. Blades generally stay sharp for 1/2 hour to

2 hours of cutting, depending on type of material and

speed of operation.

Pin End Blades

See Figure 13.

• Turn off and unplug the saw from outlet.

,_ WARNING: To avoid injury from accidental starting, always turn off and unplug the saw before installing, removing or replacing the blade.

• On the top back of the saw, rotate the quick

release knob to the left or counterclockwise to

loosen blade tension. See Figure 5.

Remove the throat plate.

Place blade through the throat plate opening with

the teeth of the blade to the front of the saw and pointing down toward the table. Engage the pin into the "V" notch of the lower blade holder.

• Pull up on the blade and push down on the saw

arm to engage the upper pin in the "V" notch of the upper blade holder.

Note: If the blade touches the hold down foot on

either side then the hold down foot must be adjusted.

Loosen the foot adjusting knob. See Figure 13.

To center the hold down foot around the saw

blade, slide the hold down foot to the side.

Tighten the foot adjusting knob.

To tension the blade, rotate the quick release knob (outer, larger knob) 114 turn to the right or clockwise to apply tension to the blade. Fine adjustments of the blade tension may be performed using the tension adjusting knob (inner, smaller knob) at any time, while the blade is under tension or not.

Replace throat plate.

Plain End •lades

See Figure 13.

• Turn off and unplug the saw from outlet.

A

WARNING: To avoid injury from accidental starting, always turn off and unplug the saw before installing, removing, or replacing the blade.

• On the top back of the saw, rotate the quick release knob to the left or counterclockwise to loosen the blade tension.See Figure 5.

Remove the throat plate.

Loosen the blade knobs by hand and remove the blade.

Place new blade through the throat plate opening

in the table with the teeth of the blade to the front of the saw and pointing down toward the table.

Next, place blade in the lower blade holder into the slot that enlarges as you loosen the blade knob.

Position blade and securely tighten blade knob.

Pull up on the blade and down on the saw's

upper arm to install blade into upper blade holder.

Note: If the blade touches the hold down foot on

either side then the hold down foot must be adjusted.

14

Loosen the foot adjusting knob. See Figure 13.

To center the hold down foot around the saw

blade, slide the hold down foot to the side.

Tighten the foot adjusting knob.

Position blade and securely tighten blade knob.

Turn the quick release knob to the right or clockwise to tension the blade.

Turn the tension adjusting knob to the right, clockwise or to the left, counterclockwise until the blade is in desired tension.

Replace throat plate.

PLAIN ENDBLADE

PLAIN END

BLADEKNOB

FOOTADJUSTING

TO RELEASE

QUICKRELEASE

KNOB

TO ENGAGE

Fig. 14

Turn tension adjusting knob (upper, smaller knob) to the right or clockwise to increase tension. Turn it to the left or counterclockwise to decrease blade tension.

Note: Adjustments of blade tension can be made at anytime. The quick release knob can be either released or engaged while making adjustments with the tension adjusting knob.

TENSIONADJUSTINGKNOB

PIN END BLADE

HOLDDOWNFOOT

TO INCREASE

TENSION

TO DECREASE

TENSION

SAWDUST

EXHAUST

ADJUSTING BLADE

See Figures 14 and 15.

TENSION

Turn off and unplug the saw.

PLAINEND

BLADEKNOB

©

,_k WARNING: Failure to unplug your saw could

result in accidental starting causing possible serious personal injury.

Fig. 13

Fig. 15

Rotate quick release knob to the right or clock- wise 1/4 turn to engage tension before using the scroll saw.

Check tension by the sound the blade makes when

plucked like a guitar string. This method of adding

tension to the blade can be developed with practice and requires knowing your scroll saw.

• Pluck the back straight edge of blade while turning tension adjusting knob. Sound should be

a musical note. Sound becomes less flat as tension increases. Sound decreases with too much tension.

Note: Be careful not to over tension the blade. Too

much tension may cause blade to break as soon as you start cutting. Too little tension may cause blade to

bend or break before teeth wear out.

Tension adjusting knob is on the top of the saw.

See Figure 5. Rotate the quick release knob

(outer, larger knob) 1/4 turn to the left or counterclockwise to release blade tension.

num,brass,copper).

GENERAL OPERATION

tocutwood,woodcompometals(alumi-

Please read and understand the following items concerning your scroll sew before attempting to use

the sew.

There is a learning curve for each person who

wants to use this sew. Dudng that pedod of time

it is expected that some blades will break until

you learn how to use and adjust the sew.

Allow the saw to cut material by guiding the workpiece into the blade as it moves. Do not force the work.

• The blade teeth cut matedal only on the down stroke.

You must guide the workpiece into the blade slowly because the teeth of the blade are very small and can only remove matedal on the down stroke.

Scroll saw blades wear out and must be replaced frequently for best cutting results. Scroll saw

blades generally stay sharp for 112 hour to 2 hours of cutting, depending on type of material and speed of operation.

To get accurate cuts, be prepared to compen-

sate for the blade's tendency to follow the wood grain as you are cutting wood.

In cutting wood, best results are achieved when cutting wood less than one inch thick.

When cutting wood thicker than one inch, the user must guide the workpiece very slowly into

the blade and take extra care not to bend or twist the blade while cutting.

When choosing a blade to use with your scroll sew, consider the following carefully:

Very fine, narrow blades should be used to

scroll cut in thin matedal 1/4 in. thick or less.

Most blade packages state the size or thickness and type of material which that blade is intended to cut. Package should also state the

radius, or size of curve, which can be cut with that blade.

Wider blades cannot cut curves as tight or small as thinner blades.

Blades wear faster:

When cutting plywood and other laminates.

When cutting matedal thicker than 3/4 in.

When cutting hardwood.

When side pressure is applied to the blade.

ON/OFF KNOB WITH VARIABLE

See Figure 16.

SPEED

Your scroll saw has an easy access On/Off knob with variable speed.

• Pull the knob out to turn ON the saw, and push

the knob in to turn OFF the sew.

Note: After saw is turned on, a hesitation before blade movement is normal.

WARNING: Never leave the saw unattended until the blade has come to a complete stop to prevent serious personal injury.

POST

ON/OFFKNOB

Fig. 16

• By turning the knob, the variable speed control

may be adjusted from the high speed of approximately 1700 SPM (Strokes Per Minute) to the low speed of approximately 500 SPM. Suggested speeds are identified under Choice of Blade and

Speed, page 18. Turn the On/Off knob to the

right or clockwise to increase strokes per minute and to the left or counterclockwiseto reduce the strokes per minute.

This motor has an electronic control that regulates the speed and provides ovedoad protection to the motor.

If the motor fails to start after about 2 seconds, push

the knob OFF and disconnect the saw from the power source. Refer to the troubleshooting chart.

Note: I1the internal overload protector has been tripped, pushing the On/Off knob OFF will reset it.

16

LOCK POST

See Figure 17.

To prevent unauthorized use of your scroll saw, we suggest that you disconnect it from the power supply and lock the knob in the OFF position. A padlock with a shackle of 5 mm or 3/16 in. diameter should be used. When the lock is installed and locked, as illustrated, the switch is inoperable. Store the padlock key in another location.

To lock the saw in the OFF position, install a

padlock through the lock post beside the knob as illustrated and lock the padlock. (Padlock is not supplied with the saw.)

,_ WARNING: For your own safety, always push

the knob OFF when machine is not in use. Also,

in the event of a power failure, push knob OFF.

Lock the scroll saw switch OFF with a padlock.

This will prevent the machine from starting up again when the power comes back on. Failure to heed this warning can result in serious personal injury.

INTERIOR SCROLL CUTTING

See Figure 18.

One of the features of a scroll saw is that it can

be used to make scroll cuts on the interior of a board without breaking or cutting through the edge or perimeter of the board.

&

WARNING: To avoid possible serious injury from accidental starting, always turn the switch

OFF and remove plug from power source outlet before removing or replacing the blade.

To make interior cuts in a board, remove the scroll saw blade as explained in the Installing

Blades section on page 14.

Drill a 114in. hole in the board to be used to make interior cuts.

Place the board on the saw table with the hole in

the board over the access hole in the table.

Install blade through hole in board then adjust the hold down foot and the blade tension. See pages 14 and 15.

When finished making the interior scroll cuts, simply remove the blade from the blade holders as described in the Installing Blades section, and remove the board from the table.

DRILLHOLE

INTERIOR

PADLOCK

ON/OFFKNOB

Fig. 17

Fig. 18

17

STACK CUTTING

See Figure 19.

After becoming well acquainted with your saw through practice and experience, you may wish to try stack cutting. Stack cutting may be used when several

identical shapes need to be cut. Several pieces of wood may be stacked on top and secured to each

other before cutting. The wood pieces may be joined together by placing double sided tape between each piece or by wrapping masking tape around the comers or ends of the stacked wood. You must attach the stacked pieces of wood to each other so they will move on the table as a single piece of material.

_k WARNING: To avoid possible, serious personal injury, do not cut more than one loose piece of material at a time.

0

Fig. 19

CHOICE OF BLADE AND SPEED

The scroll saw accepts a wide variety of blade widths and thicknesses for cutting wood and other fibrous materi- als. Your saw uses 5 inch long blades of either the pin end or the plain end style. The blade width and thickness

and the number of teeth per inch to use are determined by the type of material and the size of the radius being

cut. A full selection of scroll saw blades ere available through Sears Retail Stores.

Note: As a general rule, always select narrow blades for intricate curve cutting, and wide blades for straight and large curve cutting.

Teeth/Inch

10

Width

.110 in.

Thickness

.020 in.

Speed or

Strokes Per

Minute

1200-1700

Material Cut

15

18

.110 in.

.095 in.

.020 in.

.010 in.

600-1200

500-600

Popular size for cutting hard and soft

woods 3116 in. up to 2 in. Plastics, paper, felt, bone, etc,

Wood, plastics, extremely thin cuts on materials 3/32 in. to 1/2 in. thick.

For tight radius work in thin materials

3/32 in. to 1/8 in. wood, veneer, bone, fiber, ivory, plastic, etc.

BEFORE EACH USE:

INSPECT YOUR SAW. Disconnect the saw. To avoid injury from accidental starting, turn the switch OFF and unplug the saw before changing the setup or removing covers, guards, or blade.

INSPECT YOUR WORKPIECE. Make sure there are no nails or foreign objects in the workpiece to be cut.

• USE EXTRA CAUTION WITH LARGE, VERY

SMALL, OR AWKWARD WORKPIECES.

• Never use this tool to cut pieces too small to hold by hand.

18

• Always use extra supports (tables, saw horses, blocks, etc.) for any workpiece large enough to tip when not held down to the table top.

Never use another person as a substitute for a

table extension, or as additional support for a

workpiece or to help feed, support, or pull the workpiece.

• When cutting an irregularly shaped workpiece, plan your work so it will not pinch the blade. A

piece of molding, for example, must lay flat or be

held by a fixture or jig that will not let it twist, rock, or slip while being cut.

torollduringa cut, causingthebladeto

"bite." To avoid this, always

use a "v" block.

• Clear everything except the workpiece and related support devices off the table before plugging into power and turning the saw on.

B PLAN THE WAY YOU WILL HOLD THE

WORKPIECE FROM START TO FINISH. Do not

hand hold pieces so small that your fingers will go under the work hold-down.

BEFORE FREEING ANY JAMMED MATERIAL:

• Turn switch OFF.

Wait for all moving parts to stop.

• Unplug the saw.

WHEN BACKING OUT OF THE WORKPIECE,

THE BLADE MAY BIND IN THE KERF (CUT).

THIS IS USUALLY CAUSED BY SAWDUST

CLOGGING UP THE KERF. IF THIS HAPPENS:

• Turn switch OFF,

Wait for all moving parts to stop.

Unplug the saw.

Remove the blade from the blade holders.

Remove the workpiece with blade from the table.

Remove blade from workpiece.

&

WARNING: Before removing loose pieces from

the table, turn saw off and wait for all moving parts to stop to avoid serious personal injury.

_.

WARNING: When servicing, use only identic&l

Craftsman replacement parts. Use of any other

part may create a hazard or cause product damage.

BRONZEBEARING

WARNING: To prevent accidental starting that

could cause possible serious personal injury, turn off and unplug the saw before maintaining or lubricating your scroll saw.

GENERAL MAINTENANCE

Keep your Scroll Saw clean.

After cleaning the table top initially,apply a thin coat of automobile type (paste) wax to the table top so the wood slides easily while cutting.

ARM BEARINGS

See Figure 20.

Lubricate the arm bearings after every 50 hours of

use or whenever there is a squeak coming from the bearings.

• Carefully place the saw on its side as shown in

Figure 20. Remove the rubber cap from the

lower arm of the saw.

Squirt a few drops of SAE20 oil around the shaft

end and bronze bearing. Let oil soak in over- night, remaining in this position.

Note: Lubricate the upper arm bearing from the other

side of the saw.

_k, WARNING: If the power cord is worn, cut, or damaged in any way, have it replaced

immediately by a qualified service technician at a

Sears store to avoid risk of personal injury.

MOTOR BRUSHES

See Figure 21.

Your saw has externally accessible brush assemblies

that should be checked periodically for wear. When one of the two brushes becomes worn, replace both brushes.

• Unplug your saw.

_, WARNING: injury.

Failure to unplug your saw could result in accidental starting causing serious

19

Remove brush cap with a flat blade screwdriver.

Remove brush assembly. Gently pry the brush assembly out using a small screwdriver, point of a nail or paperclip, etc.

Check for wear. If one brush is worn down shorter than 114 in., replace both brushes. Do

not replace one side without replacing the other.

Reassemble using new brush assembly. Make sure curvature of brush matches curvature of

motor and that brush moves freely in brush tube.

Use the blunt end of something thin (eraser end of pencil, etc.) to push the brush into the tube until it stays.

Make sure brush cap is oriented correctly

(straight) and replace.

Tighten brush cap using a hand powered screw-

ddver only. Do not overtighten.

Repeat for other brush.

\

_j_1.

BRUSHCAP

Fig. 21

,_ WARNING: For your own safety, turn switch OFF and remove plug from power outlet before adjusting or aligning your scroll saw.

PROBLEM

Motor will not run.

Blades breaking.

Vibration (there is always some vibration when the saw is running).

Blade runout (blade not properly aligned with arm motion).

CAUSE SOLUTION

1. Problem with ON-OFF switch, I.

power cord, or outlet.

Have worn parts replaced before using

Scroll Sew again. Have the proper outlet installed by a qualified electrician.

2. Motor Defective.

2,

Do not attempt any repair. Have

repaired by a qualified service techni- cian at a Sears store or repair center.

1. Too much tension.

2, Feeding too quickly.

3, Wrong blade.

4. Blade twisting in wood.

1. Improper mounting of saw.

2. Mounting surface.

3. Loose table or table resting against motor.

4. Loose motor mounting.

1. Adjust tension.

2. Reduce feed rate.

3.

Narrow blades for cutting thin wood or

tight corners and turns, wide blades for thicker wood or wide turns,

4.

Reduce side pressure on blade, check blade tension.

1. Check mounting.

2. Check mounting in manual.

3. Tighten table lock knob.

4. Tighten mounting screws.

1. Blade holders out of line.

1.Realign blade.

20

21

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216260

Po r_

36

FIGURE A

_-35

34

39

/

/*°

27

/'/25

26

./'/"

24 23

/-/

52

15

18

17

28 29

16 15

33 32 22 21

49

Po

Co

Key

No.

19

20

21

22

23

24

25

26

15

16

17

18

12

13

14

6

7

4

5

1

2

3

10

11

8

9

Pert

Number

979817-001

980119-001

979814-001

979813-001

979832-001

979810-001

979809-001

979807-001

979806-001

979729-001

979730-001

979808-001

979805-001

979804-001

979803-001

979802-001

980123-001

979788-001

979786-001

979785-001

979784-001

979775-001

979776-001

979774-001

979773-001

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216260

Description

Blade Lock Knob...........................................

1

Blade Holder .................................................

1

Spring Pin .....................................................

1

Spring Pin .....................................................

1

Saw Blade .....................................................

1

Throat Plate ..................................................

1

Table .............................................................

1

Table Screw ..................................................

1

Blade Drawer ................................................

1

Blade Drawer Bracket ...................................

1

Washer .........................................................

3

Screw (Pan Hd.) ...........................................

3

Screw (Pan Hd.) ...........................................

2

Bevel Lock Knob ...........................................

1

Flat Washer ..................................................

2

Scale .............................................................

1

Miter Scale Bracket ......................................

1

Motor (Includes Kay Nos. 19, 20, 21, & 22). 1

Clamp Screw ................................................

2

Brush Holder .................................................

2

Brush Assembly ............................................

2

Brush Cap .....................................................

2

Counterbalance ............................................

1

Clamp Screw ................................................

1

Spacer ..........................................................

1

Screw (Pan Hd.) ...........................................

1

PARTS LIST FOR FIGURE A

Ouan.

Key

No.

Part

Number

45

46

47

48

49

50

51

52

37

38

39

40

41

42

43

44

30

31

32

33

34

35

36

27

28

29

979772-001

979820-001

979821-001

979822-001

979823-001

979824-001

979825-001

979771-001

979769-001

979768-001

979770-001

979766-001

979767-001

979801-001

979800-001

979799-001

979798-001

979797-001

979796-001

979794-001

979793-001

979795-001

979790-001

979791-001

979789-001

979777-001

Description Quan.

Indicator ........................................................

1

Hex Bolt ........................................................

1

Hex Nut .........................................................

1

Hex Bolt (Socket Hd. Special) ...................... 1

Washer .........................................................

1

Stopper .........................................................

1

Spring Pin .....................................................

1

Base ..............................................................

1

Hex Bolt ........................................................

4

Waming Label ...............................................

1

Hex Bolt ........................................................

3

Screw (Pan Hd.) ...........................................

2

Nozzle ...........................................................

1

Screw (Pan Hd.) ...........................................

2

Control Box ...................................................

t

PC Board Assembly .....................................

t

Gasket ..........................................................

1

On/Off Knob ..................................................

1

Knob Label ....................................................

1

Motor Pointer ................................................

t

Switch Label .................................................

t

Motor Cover ..................................................

1

Power Cord Assembly .................................. 1 "

Strain Relief ..................................................

1

Screw (Pan Hd.) ...........................................

4

Motor Screw ..................................................

3

*** Available at your nearest Sears Retail Store.

j:.

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216260

21

13

29

30

28

20

37

38

12

14

12

39

40

18

15

16

FIGURE B

Po

O1

Key

No.

12

13

14

10

11

8

9

3

4

1

2

5

6

7

15

16

17

18

19

2O

21

22

23

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216260

I

The model number will be found on a plate attached to the frame. Always mention the model number in all correspondence regarding your SCROLL

SAW or when ordering repair parts.

Pad

Number

979827-001

979737-001

979736-001

979742-001

979735-001

979766-001

979734-001

979828-001

979733-001

979830-001

979732-001

979765-001

979763-001

979764-001

979814-001

979813-001

980119-001

979817-001

979762-001

979731-001

979761-001

979760-001

979769-001

Description Quart.

Tension AdjustingKnob ........................... ,... 1

Spring Pin .....................................................

1

Quick Release Knob .....................................

1

Rubber Boot..................................................

1

Cam ..............................................................

1

Arm Spdng ....................................................

1

Tension Wedge .............................................

1

Washer .........................................................

1

Tension Bolt ..................................................

1

E-Ring ...........................................................

1

Tension Wedge .............................................

1

Bushing.........................................................

4

Lower Arm ....................................................

1

Spacer Bearing .............................................

2

Spring Pin .....................................................

1

Spring Pin .....................................................

1

Blade Holder .................................................

1

Blade Lock Knob ...........................................

1

Link ...............................................................

1

Spdng Washer ..............................................

2

Screw (Socket Hd. Cap) ...............................

1

Washer .........................................................

2

Screw (Pan Hd.) ...........................................

2

PARTS LIST FOR FIGURE A

Key

No.

28

29

30

31

24

25

26

27

35

36

37

38

32

33

34

39

40

41

42

43

Pad

Number

979758-001

979826-001

979752-001

979751-001

979740-001

979738-001

979741-001

979831-001

979744-001

979745-001

979749-001

979743-001

979747-001

979746-001

979748-001

979753-001

979754-001

979755-001

979757-001

979829-001

972000-549

Description Quen.

Ball Beadng ..................................................

2

Bolt (Hex Hd.) ...............................................

1

Right Arm Cover ...........................................

1

Spring Pin .....................................................

1

Screw (Pan Hd.) ...........................................

8

Data Plate .....................................................

1

Hold Down Foot Lock Knob .......................... 1

Support Bar Assembly ..................................

1

Foot AdjustingKnob .....................................

1

Support Plate ................................................

1

Hold Down Clamp .........................................

1

Washer/Spacer .............................................

1

Hold Down Foot ............................................

1

Air Hose ........................................................

1

Air Diaphragm ...............................................

1

Upper Arm ....................................................

1

Hand Warning Label .....................................

1

Left Arm Cover ..............................................

1

Logo Plate .....................................................

1

Rubber Stopper ............................................

3

Owners Manual

I

|

I

* Standard Hardware Item -- May Be Purchased Locally ** Available From Division 98 - Source 980.00

For in-home major brand repair service:

Call 24 hours a day, 7 days a week

1-800-4-MY-Home

TM

(1-800-469-4663)

Para pedir servicio de reparacibn a domicilio - 1-800-676-5811

In Canada for all your service and parts needs call

- 1-800-665-4455

Au Canada pour tout le service ou les pi_ces

For the repair or replacement parts you need:

Call 7 am - 7 pm, 7 days a week

1-800-366-PART (1-800-366-7278)

Para ordenar piezas con entrega a domicilio - 1-800-659-7084

For the location of a Sears Parts and Repair Center in your area:

Call 24 hours a day, 7 days a week

1-800-488-1222

For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement:

Call 9 am - 5 pm, Monday - Saturday

1-800-827-6655

The Service Side of Sears s"

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement