Yamaha XVS1100AWR Service manual

FOREWORD
This Supplementary Service Manual has been prepared to introduce new service and data for the
XVS1100A. For complete service information procedures it is necessary to use this Supplementary
Service Manual together with the following manual.
XVS1100L/XVS1100LC SERVICE MANUAL: LIT-11616-12-63 (5EL-28197-E0)
XVS1100AM/XVS1100AMC SUPPLEMENTARY SERVICE MANUAL:
LIT-11616-13-36 (5KS-28197-E0)
EB000000
XVS1100AWR(C)
XVS1100ATR(C)
SUPPLEMENTARY
SERVICE MANUAL
 2002 by Yamaha Motor Co., Ltd.
First edition, November 2002
All rights reserved. Any reproduction or
unauthorized use without the written
permission of Yamaha Motor Co., Ltd.
is expressly prohibited.
EAS00003
NOTICE
This manual was produced by the Yamaha Motor Company, Ltd. primarily for use by Yamaha dealers
and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one manual. Therefore, anyone who uses this book to perform maintenance and repairs on Yamaha Vehicles
should have a basic understanding of mechanics and the techniques to repair these types of vehicles.
Repair and maintenance work attempted by anyone without this knowledge is likely to render the vehicle unsafe and unfit for use.
This model has been designed and manufactured to perform within certain specifications in regard to
performance and emissions. Proper service with the correct tools is necessary to ensure that the vehicle will operate as designed. If there is any question about a service procedure, it is imperative that
you contact a Yamaha dealer for any service information changes that apply to this model. This policy
is intended to provide the customer with the most satisfaction from his vehicle and to conform with
federal environmental quality objectives.
Yamaha Motor Company, Ltd. is continually striving to improve all of its models. Modifications and significant changes in specifications or procedures will be forwarded to all authorized Yamaha dealers
and will appear in future editions of this manual where applicable.
This Service Manual contains information regarding periodic maintenance to the emission control system. Please read this material carefully.
NOTE:
Designs and specifications are subject to change without notice.
IMPORTANT INFORMATION
Particularly important information is distinguished in this manual by the following notations.
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!
WARNING
CAUTION:
NOTE:
Failure to follow WARNING instructions could result in severe injury or death to
the motorcycle operator, a bystander or a person inspecting or repairing the
motorcycle.
A CAUTION indicates special precautions that must be taken to avoid damage
to the motorcycle.
A NOTE provides key information to make procedures easier or clearer.
EB002000
HOW TO USE THIS MANUAL
MANUAL ORGANIZATION
This manual consists of chapters for the main categories of subjects. (See “Illustrated symbols”)
1st title 1 :
This is the title of the chapter with its symbol in the upper right corner of each page.
2nd title 2 : This title indicates the section of the chapter and only appears on the first page of each
section. It is located in the upper right corner of the page.
3rd title 3 : This title indicates a sub-section that is followed by step-by-step procedures accompanied by corresponding illustrations.
EXPLODED DIAGRAMS
To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each removal and disassembly section.
1. An easy-to-see exploded diagram 4 is provided for removal and disassembly jobs.
2. Numbers 5 are given in the order of the jobs in the exploded diagram. A number that is enclosed by
a circle indicates a disassembly step.
3. An explanation of jobs and notes is presented in an easy-to-read way by the use of symbol marks
6 . The meanings of the symbol marks are given on the next page.
4. A job instruction chart 7 accompanies the exploded diagram, providing the order of jobs, names of
parts, notes in jobs, etc.
5. For jobs requiring more information, the step-by-step format supplements 8 are given in addition to
the exploded diagram and the job instruction chart.
2
1
6
3
8
5
4
7
EB003000
1
ILLUSTRATED SYMBOLS
2
GEN
INFO
SPEC
3
4
CHK
ADJ
ENG
5
6
CHAS
CARB
7
8
TRBL
SHTG
ELEC
11
12
13
14
15
16
20
23
Symbols 9 to 16 indicate the following.
9 Serviceable with engine mounted
10
9
17
The following symbols are not relevant to every
vehicle.
Symbols 1 to 8 indicate the subject of each
chapter.
1 General information
2 Specifications
3 Periodic checks and adjustments
4 Engine
5 Carburetor
6 Chassis
7 Electrical system
8 Troubleshooting
18
10
11
12
13
14
15
16
19
21
22
24
Filling fluid
Lubricant
Special tool
Tightening torque
Wear limit, clearance
Engine speed
Electrical data
Symbols 17 to 22 in the exploded diagrams indicate the types of lubricants and lubrication
points.
17
18
19
20
21
22
Engine oil
Gear oil
Molybdenum disulfide oil
Wheel bearing grease
Lithium soap base grease
Molybdenum disulfide grease
Symbols 23 to 24 in the exploded diagrams indicate the following:
23 Apply locking agent (LOCTITER)
24 Replace the part
CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CABLE ROUTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
2
2
3
5
PERIODIC CHECKS AND ADJUSTMENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL
SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
GENERAL MAINTENANCE AND LUBRICATION CHART . . . . . . . . . 15
CHASSIS
FRONT WHEEL AND BRAKE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE FRONT WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE FRONT WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE BRAKE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE FRONT WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR WHEEL AND BRAKE DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MUFFLER AND BRAKE CALIPER . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE REAR WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE REAR WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE REAR WHEEL DRIVE HUB . . . . . . . . . . . . . . . . .
INSTALLING THE REAR WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
19
19
21
23
24
24
25
27
27
28
28
ELECTRICAL
CHECKING THE SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
XVS1100AWR(C)/XVS1100ATR(C) WIRING DIAGRAM
GENERAL SPECIFICATIONS
SPEC
SPECIFICATIONS
GENERAL SPECIFICATIONS
Item
Standard
Model code
XVS1100: 5KSJ (For U.S.A.)
5KSK (For CAL)
5KSU (For U.S.A.)
5KSV (For CAL)
Dimensions
Overall length
Overall width
Overall height
Seat height
Wheelbase
Minimum ground clearance
Minimum turning radius
2460 mm (96.9 in)
945 mm (37.2 in)
1,095 mm (43.1 in)
710 mm (28 in)
1645 mm (64.8 in)
140 mm (5.5 in)
3400 mm (133.9 in)
Basic weight
With oil and a full fuel tank
285 kg (628 lb)
Tire
Type
Size
Manufacturer
Type
front
rear
front
rear
front
rear
Tire pressure (cold tire)
0 X 90 kg (0 X 198 lb) load*
front
rear
90 kg (198 lb) X Maximum load*
front
rear
Tubeless
130/90-16M/C 67S
170/80-15M/C 77S
BRIDGESTONE/DUNLOP
BRIDGESTONE/DUNLOP
EXEDRA G703/D404F
EXEDRA G702/D404G
225 kPa (2.25 kg/cm2, 32.6 psi)
250 kPa (2.5 kg/cm2, 36.3 psi)
225 kPa (2.25 kg/cm2, 32.6 psi)
250 kPa (2.5 kg/cm2, 36.3 psi)
* Load is the total weight of the cargo, rider,
passenger and accessories.
–1–
MAINTENANCE SPECIFICATIONS
SPEC
MAINTENANCE SPECIFICATIONS
ENGINE
Item
Standard
Carburetor
I.D. mark
Main jet
Main air jet
Jet needle
Needle jet
Pilot air jet
(M.J)
(M.A.J)
(J.N)
(N.J)
(P.A.J.1)
(P.A.J.2)
Pilot outlet
(P.O)
Pilot jet
(P.J)
Bypass 1
(B.P.1)
Bypass 2
(B.P.2)
Bypass 3
(B.P.3)
Valve seat size
(V.S)
Starter jet
(G.S.1)
Starter jet
(G.S.2)
Throttle valve size
(Th.V)
Fuel level (above the line on
the float chamber)
(F.L)
Engine idle speed
Intake vacuum
Engine oil temperature
Fuel pump
Type
Model/manufacturer
Consumption amperage
Output pressure
<max>
Limit
5EL5 40 (U.S.A.)
5EL6 50 (CAL)
#1: #110, #2: #112.5
#55
5DL 43-53-1
P-0M
#63.8
#145
1.0
#17.5
0.8
0.8
0.8
1.2
#42.5
0.8
#125
4 X 5 mm (0.16 X 0.20 in)
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
950 X 1,050 r/min
34.7 X 37.3 kPa (260 X 280 mmHg)
75 X 85_C (167 X 185_F)
SSS
SSS
SSS
Electrical type
UC-Z61B/MITSUBISHI
0.8 A
12 kPa (0.12 kg/cm2,1.7 psi)
SSS
SSS
SSS
SSS
CHASSIS
Item
Standard
Front suspension
Front fork travel
Fork spring free length
Fitting length
Collar length
Spring rate
Stroke
Optional spring
Oil capacity
Oil level
Oil grade
140 mm (5.51 in)
371.9 mm (14.64 in)
(K1)
(K2)
(K1)
(K2)
334.4 mm (13.17 in)
183 mm (7.20 in)
4.41 N/mm (0.45 kg/mm, 25.18 lb/in)
6.37 N/mm (0.65 kg/mm, 36.37 lb/in)
0 X 77.5 mm (0 X 3.05 in)
77.5 X 140 mm (3.05 X 5.51 in)
No
0.483 L (483 cm3, 17.01 Imp OZ,
16.34 US OZ)
104 mm (4.09 in)
Fork oil 10WT or equivalent
–2–
Limit
SSS
350 mm
(13.78 in)
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
MAINTENANCE SPECIFICATIONS
Item
Rear suspension
Shock absorber travel
Spring free length
Fitting length
Spring rate
Stroke
Optional spring
Front wheel
Type
Rim size
Rim material
Rim runout limit
Rear wheel
Type
Rim size
Rim material
Rim runout limit
SPEC
Standard
Limit
51 mm (2.01 in)
181 mm (7.13 in)
169 mm (6.65 in)
132.3 N/mm (13.49 kg/mm, 755.43 lb/in)
0 X 51 mm (0 X 2.01 in)
No
SSS
SSS
SSS
SSS
SSS
SSS
radial
Cast wheel
16M/C
MT 3.00
Aluminum
SSS
lateral
SSS
SSS
SSS
SSS
1.0 mm
(0.04 in)
0.5 mm
(0.02 in)
radial
Cast wheel
15M/C
MT4.50
Aluminum
SSS
lateral
SSS
(K1)
(K1)
SSS
SSS
SSS
1.0 mm
(0.04 in)
0.5 mm
(0.02 in)
ELECTRICAL
Item
Standard
Limit
T.C.I.
Pickup coil resistance/color
T.C.I. unit model/manufacturer
189 X 231 Ω at 20_C (68_F)/Gray – Black SSS
J4T142/MITSUBISHI
SSS
Rectifier/regulator
Regulator type
Model/manufacturer
No load regulated voltage
Rectifier capacity
Withstand voltage
Semi-conductor, short-circuit type
SH678-11/SHINDENGEN
14.1 X 14.9 V
22 A
200 V
–3–
SSS
SSS
SSS
SSS
SSS
MAINTENANCE SPECIFICATIONS
Item
Electric starter system
Type
Starter motor:
Model/manufacturer
Output
Armature coil resistance
Brush overall length
Brush spring pressure
SPEC
Standard
Limit
Constant mesh type
SSS
SM-13/MITSUBA
0.6 kW
0.025 X 0.035 Ω at 20_C (68_F)
12.5 mm (0.49 in)
SSS
SSS
SSS
4 mm
(0.16 in)
SSS
7.65 X 10.01 N
(780 X 1021 g, 27.51 X 36.01 OZ)
28 mm (1.10 in)
0.7 mm (0.03 in)
27 mm
(1.06 in)
SSS
MS5F-421 /JIDECO
180 A
SSS
SSS
Starting circuit cut-off relay
Model/manufacturer
Coil resistance
G8R-30Y-U/OMRON
202.5 X 247.5 Ω at 20_C (68_F)
SSS
Thermostat switch
Model/manufacturer
5FU/NIPPON THERMOSTAT
SSS
Commutator diameter
Mica undercut
Starter relay:
Model/manufacturer
Amperage rating
–4–
CABLE ROUTING
SPEC
EB206000
CABLE ROUTING
1
2
3
4
5
6
7
8
9
10
11
12
Clutch cable
Starter cable
Handlebar switch lead (left)
Handlebar switch lead (right)
Spark plug lead
Throttle cable
Fuel hose (fuel cock to filter)
Fuel breather hose (fuel tank roll
over valve) (for CAL)
Fuse box
Alarm connector
Fuel pump lead
Speed sensor lead
Sidestand switch lead
Neutral switch lead
Pickup coil lead
To engine
A.C. magneto lead
Ventilation hose
Sensing hose (AI system to carburetor joint)
20 Fuel hose (fuel pump to carburetor)
21 Clip
22 Brake hose
13
14
15
16
17
18
19
–5–
23
24
25
26
27
28
29
30
31
Heat protector
Speedometer lead
Wire harness
Purge hose (carburetor to solenoid valve) (for CAL)
Fitting plate
Fuel hose (inlet) (fuel filter to fuel
pump)
Fuel hose (outlet) (fuel pump to
carburetor)
Alarm connector lead
Wire harness
CABLE ROUTING
A Fasten the handlebar switch C Clamp the wire harness with the
lead (left and right) to the handlehook of frame side.
bar with plastic locking tie and D When installing the pipe of
cut the end of tie.
throttle cable press it inside.
B Lay out the throttle and starter E Clamp the fuel hoses to the
cables in three rows and secure
frame with the clamp.
them with a clip. (Two points at F Cross the fuel hose (fuel cock
the front and rear.) Care should
side) and fuel hose (carburetor
be taken at this time so that the
side) between guide of frame
clip does not fall to the outside
and clamp. (carburetor side is
against the vertical face of the
upper)
vehicle. Point the opening part of G When connecting the sensing
the clip to the inside of the vehose (carburetor joint to AI syshicle.
tem) with a nozzle.
–6–
SPEC
H Push the wire harness inside of
the side cover.
I Push the sensing hose inside of
the tool box plate and not bend
the sensing hose.
J Through the wire harness of solenoid valve between AIS duct
and fuel hose (for CAL).
K Fasten the alarm lead with a plastic band on the tool box plate.
L Fasten the sidestand switch lead
to the bracket of tool box plate
with plastic locking tie.
CABLE ROUTING
M Fasten the lead with locking tie
near the side cover.
N Position the all connectors inside
of the connector cover.
O Route the clutch cable through
the cable guide.
P Fasten the handlebar switch
leads (left and right) under the
handle crown with a plastic
band. Set the band at four
notches and install it no slacking.
Q Route the each hoses through the
frame guide and do not pinch it.
R When installing the fitting plate,
do not pinch the each hoses and
wireharness.
S When install the AI system push
the wire harness to space of rearside.
–7–
SPEC
CABLE ROUTING
1
2
3
4
5
6
7
8
9
10
11
12
Battery
Battery positive (+) lead
Starter motor positive (+) lead
Speedometer lead
Fuel hose (fuel pump to carburetor)
Spark plug lead
Main switch lead
Throttle cable
Front brake hose
Handlebar switch lead (right)
Headlight lead
Ignition coil
13 Breather hose
14 Purge hose (carburetor to sole15
16
17
18
19
20
21
22
23
24
noid valve) (For CAL)
Rear brake switch
Reserve hose
Air filter drain hose
Delay relay
Battery negative (–) lead
Oil level switch lead
Rear brake light switch lead
Light reduce relay
Rectifier/ regulator
Stay 1
–8–
25
26
27
28
29
30
31
32
33
34
35
SPEC
Down tube
Rear brake hose
Frame
Stay 2
Turn signal relay
Handlebar switch lead (left)
Silencer
Throttle position sensor lead
Carburetor heater lead
Thermo switch lead
Horn
CABLE ROUTING
36 Rectifire/ regulator and light (re-
duce relay) lead
A Clamp the battery positive (+)
lead to the battery with battery
band.
B Connect the battery negative (–)
lead and push it in to the space
between battery box and battery.
C Push the wireharness into the
space between frame and starter motor relay.
–9–
SPEC
D Route the harness and starter
motor (+) lead, that are connected to the rectifier regulator
and other equipment, by the outside of the frame side bracket
and then secure it by passing the
band through the weight saving
hole of the bracket. (The securing point should be within 0 to 10
mm (0 to 0.39 in) right above the
junction point of harness side
leads that are connected with the
battery (–) lead.)
CABLE ROUTING
SPEC
E Connect the purge hose (carbu- J Fasten the wire harness, starter O Make sure to insert the rectifier
retor side-solenoid valve side)
motor positive (+) lead and batregulator coupler sufficiently unwith joint, knob is out side of frame.
tery negative (–) lead to the
til the sound is heard.
F Route the front turn signal / posiframe with a plastic locking tie.
P To rear brake.
tion light lead and headlight lead K 70 mm (2.76 in)
Q Fasten the rear brake switch
through the rear of headlight L Fasten the rear brake switch lead
lead with a band to down tube.
body hole.
and master cylinder reservoir
(four point)
G Connect the ignition coil lead at
hose to the down tube with a plas- R Cutting part at the edge of the
red tape to the right side.
tic locking tie, and cut the end of
band.
H Knob of clip is rearside of body.
locking tie and position is inside of S 30_ X 45_
I Fasten the rear brake switch
frame.
lead to the rear brake switch M 20 mm (0.79 in) (from bead end.)
bracket with a plastic locking tie N Locate the band to forward of
and cut of the end, inside of frame.
down tube.
–10–
CABLE ROUTING
T Fasten the oil level sensor lead V Arrange the throttle position senwith a locking tie to battery box.
sor connector, carburetor heater
Fix to the battery box with the
connector and thermo switch
band. To fix, align the band to the
connector between the starting
bottom of the box’s hole while fixcircuit cut off relay and high tening the lead to the back of the box
sion code.
(inside the body). The cutting part W Secure to the battery box with
at the edge of the band comes to
the band, cut the surplus section
the front side of the body.
and then point the locking secU Clamp the handlebar switch lead
tion to the regulator side.
(right) to the frame with a holder.
The part to open and shut is outside of the body.
–11–
SPEC
X Push the light reduce lead and
the terminal-coupler lead for the
carburetor heater into the deepest position in the groove of the
battery box.
CABLE ROUTING
1
2
3
4
5
6
7
8
9
10
11
Front brake hose
Throttle cable
Master cylinder reservoir hose
Spark plug lead
Purge hose (carburetor to solenoid valve) (for CAL)
Rear brake light switch lead
Rear brake hose
Fuel hose (fuel pump to carburetor)
Delay relay
Battery negative (–) lead
Battery negative (–) lead connector
12
13
14
15
16
17
18
19
20
21
22
Battery
Battery positive (+) lead
Tail/ brake light lead
Starter relay
Starter motor positive (+) lead
Fuel tank breather hose (fuel
tank to roll over valve) (for CAL)
Fuel pump outlet hose
Fuel pump inlet hose
Ventilation hose
Starter cable
Sensing hose (AI system to carburetor joint)
–12–
23
24
25
26
27
28
29
30
31
32
33
34
35
SPEC
Fuel hose (fuel cock to fuel filter)
Throttle position sensor lead
Carburetor heater lead
Tappet cover
Clutch cable
Thermo switch lead
Wire harness
Frame
Igniter unit
Igniter plate
Fuel filter
Tool box plate
Speedometer lead connecter
CABLE ROUTING
SPEC
A Clamp the throttle cables with F Route the battery positive (+) J Position the mark on the steel
the holder. Position the end of
lead through the slit of the batband to forward.
clip downword.
tery box.
K Fasten the wire harness with a
B Route the rear brake switch lead G Secure the igniter unit lead and
band on the tool box plate.
under the master cylinder resertail brake light lead to the frame L Fasten the wire harness to the
vor hose.
with a clamp. Point the
frame with a plastic locking tie.
C Position the band end of right
open / close section to the upper
Position the locking tie front of
side bracket.
side of the vehicle.
the holder.
D Position the steel band end to H To the rear fender.
M Route the wire harness outside
forward.
I Connect the wire harness to the
of the guide on the frame.
E Position the steel band end to
igniter unit through the hole of ig- N Clamp the clutch cable and startright side.
niter plate.
er cable with a holder.
Position the end of holder down
side.
–13–
CABLE ROUTING
O Route the igniter lead through
the igniter plate hole to the wireharness.
P To the wire harness.
Q Clamp the tail / brake light lead
with mud guard clamp.
R Clamp the tail / brake light lead
with a holder on the mud guard.
S Position the locking tie upward.
T Forward.
–14–
SPEC
INTRODUCTION/PERIODIC MAINTENANCE CHART FOR
THE EMISSION CONTROL SYSTEM / GENERAL MAINTENANCE AND
LUBRICATION CHART
CHK
ADJ
EAS00036
PERIODIC CHECKS AND ADJUSTMENTS
INTRODUCTION
This chapter includes all information necessary to perform recommended checks and adjustments. If
followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a
longer service life and reduce the need for costly overhaul work. This information applies to vehicles
already in service as well as to new vehicles that are being prepared for sale. All service technicians
should be familiar with this entire chapter.
PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL
SYSTEM
INITIAL
NO.
1
*
2
ITEM
REMARKS
ODOMETER READINGS
600 mi
(1,000 km)
or
1 month
4,000mi
(7,000 km)
or
6 months
8,000 mi
(13,000
km)
or
12 months
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
12,000 mi
(19,000 km)
or
18 months
16,000 mi
(25,000 km)
or
24 months
20,000 mi
(31,000 km)
or
30 months
Valve clearance
S Check and adjust valve clearance when
engine is cold.
Spark plugs
S Check condition.
S Adjust gap and clean.
S Replace at 8,000 mi (13,000 km) or 12
months and thereafter every 8,000 mi
(13,000 km) or 12 months.
Ǹ
Replace.
Ǹ
Replace.
Ǹ
3
*
Crankcase ventilation
system
S Check ventilation hose for cracks or damage.
S Replace if necessary.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
4
*
Fuel line
S Check fuel hoses for cracks or damage.
S Replace if necessary.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
5
*
Fuel filter
S Replace initial 20,000 mi (31,000 km) and
thereafter every 20,000 mi (31,000 km).
6
*
Exhaust system
S Check for leakage.
S Tighten if necessary.
S Replace gasket(s) if necessary.
7
*
Carburetor
synchronization
S Adjust synchronization of carburetors.
8
*
Idle speed
S Check and adjust engine idle speed.
S Adjust cable free play.
9
*
Evaporative emission
control system**
S Check control system for damage.
S Replace if necessary.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the
service.
** California only
GENERAL MAINTENANCE AND LUBRICATION CHART
INITIAL
NO.
1
2
*
3
ITEM
REMARKS
4,000mi
(7,000 km)
or
6 months
8,000 mi
(13,000 km)
or
12 months
12,000 mi
(19,000 km)
or
18 months
16,000 mi
(25,000 km)
or
24 months
20,000 mi
(31,000 km)
or
30 months
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Engine oil
S Replace.
S Warm engine before draining.
Ǹ
Engine oil filter
element
S Replace.
Ǹ
Air filter element
S Clean or replace if necessary.
4
*
Brake system
S Check operation fluid level, and fluid leakage.
S Correct accordingly.
S Replace pads if necessary.
5
*
Clutch
S Check operation.
S Adjust or replace cable.
6
*
Final gear oil
S Check oil level and leakage.
S Replace at initial 600 mi (1,000 km) or 1 month
and thereafter every 18,000 mi (25,000 km) or
24 months.
S Hypoid gear oil SAE 80 (API GL4)
7
*
Control and meter cables
S Apply chain, lube thoroughly.
S Yamaha Chain and Cable Lube or engine oil
SAE 10W-30 (API SE)
ODOMETER READINGS
600 mi
(1,000 km)
or
1 month
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Replace.
Ǹ
–15–
Ǹ
Check.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
CHK
ADJ
GENERAL MAINTENANCE AND LUBRICATION CHART
INITIAL
NO.
ITEM
600 mi
(1,000 km)
or
1 month
REMARKS
S Check swingarm pivot for play.
S Correct if necessary.
S Moderately repack every 16,000 mi (25,000
km) or 24 months with lithium-soap-based
grease.
ODOMETER READINGS
4,000mi
(7,000 km)
or
6 months
8,000 mi
(13,000 km)
or
12 months
12,000 mi
(19,000 km)
or
18 months
16,000 mi
(25,000 km)
or
24 months
20,000 mi
(31,000 km)
or
30 months
8
*
Swingarm pivot
shaft
9
*
Rear suspension
link pivots
S Check operation.
S Correct if necessary.
10
Brake and clutch
lever pivot shafts
S Apply chain lube thoroughly.
S Lithium-soap-based grease.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
11
Brake pedal and
shift pedal shafts
S Apply chain lube thoroughly.
S Lithium-soap-based grease.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
12
Sidestand pivot
S Check operation.
S Lubricate and repair if necessary.
S Lithium-soap-based grease.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Front fork
S Check operation and for oil leakage.
S Correct accordingly.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Repack.
Ǹ
13
*
Repack.
Ǹ
Ǹ
14
*
Steering bearings
S Check bearing play and steering for smooth
operation.
S Correct if necessary.
S Moderately repack every 18,000 mi (25,000
km) or 24 months with lithium-soap-based
grease.
15
*
Wheel bearings
S Check bearings for looseness and damage.
S Replace if necessary.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
16
*
Wheels
S Check runout and for damage.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
17
*
Sidestand switch
S Check operation.
S Replace if necessary.
18
*
Tires
S Check tire tread wear and for damage.
S Replace if necessary.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
19
*
Shock absorber
assembly
S Check operation and for oil leakage.
S Replace if necessary.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
20
*
Chassis fasteners
S Make sure that all nuts, bolts and screws
are properly tightened.
S Tighten if necessary.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
21
*
Throttle grip housing and cable
S Check operation and free play.
S Adjust the throttle cable free play if necessary.
S Lubricate the throttle grip housing and
cable.
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
Ǹ
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the
service.
NOTE:
From 24,000 mi (37,000 km) or 36 months, repeat the maintenance intervals starting from 4,000 mi
(7,000 km) or 6 months.
NOTE:
F Air filter
S This model’s air filter is equipped with a disposable oil-coated paper element, which must not be
cleaned with compressed air to avoid damaging it.
S The air filter element needs to be replaced more frequently when riding in unusually wet or dusty
areas.
F Hydraulic brake service
S After disassembling the brake master cylinders and calipers, always change the fluid. Regularly
check the brake fluid levels and fill the reservoirs as required.
S Every two years replace the internal components of the brake master cylinders and calipers, and
change the brake fluid.
S Replace the brake hoses every four years and if cracked or damaged.
F Engine oil type
S Yamalube 4 ( 20W-40) or engine oil SAE 20W-40 (API SE) for temperatures of 5_C (40_F) or above.
S Yamalube 4 (10W-30) or engine oil SAE 10W-30 (API SE) for temperatures of 15_C (60_F) or below.
–16–
FRONT WHEEL AND BRAKE DISCS
CHAS
CHASSIS
FRONT WHEEL AND BRAKE DISCS
59 Nm (5.9 mSkg, 43 ftSlb)
20 Nm (2.0 mSkg, 14 ftSlb)
40 Nm (4.0 mSkg, 29 ftSlb)
23 Nm (2.3 mSkg, 17 ftSlb)
Order
Job name/Part name
Q’ty
Remarks
Remove the parts in the order listed.
Stand the motorcycle on a level surface.
Removing the front wheel and brake
discs
WARNING
Securely support the motorcycle so
there is no danger of it falling over.
1
2
3
4
5
6
7
Reflector
Brake calipers
Front wheel axle pinch bolt
Front wheel axle
Front wheel assembly
Collars
Brake discs
2
2
1
1
1
2
2
–17–
Refer to “REMOVING/INSTALLING
THE FRONT WHEEL”.
Refer to “INSTALLING THE FRONT
WHEEL”.
For installation, reverse the removal
procedure.
FRONT WHEEL AND BRAKE DISCS
Order
1
2
3
Job name/Part name
Disassembling the front wheel
Oil seals
Bearings
Collar
Q’ty
CHAS
Remarks
Disassemble the parts in the order listed.
2
2
1
For assembly, reverse the disassembly
procedure.
–18–
FRONT WHEEL AND BRAKE DISCS
CHAS
EAS00521
REMOVING THE FRONT WHEEL
1. Stand the motorcycle on a level surface.
WARNING
Securely support the motorcycle so that
there is no danger of it falling over.
NOTE:
Place the motorcycle on a suitable stand so that
the front wheel is elevated.
2. Remove:
S reflectors 1 (left and right)
S brake calipers 2 (left and right)
NOTE:
Do not squeeze the brake lever when removing
the brake calipers.
3. Loosen:
S pinch bolt (front wheel axle) 1
S front wheel axle 2
4. Elevate:
S front wheel
NOTE:
Place the motorcycle on a suitable stand so that
the front wheel is elevated.
EAS00526
CHECKING THE FRONT WHEEL
1. Check:
S wheel axle
Roll the wheel axle on a flat surface.
Bends ! Replace.
WARNING
Do not attempt to straighten a bent wheel axle.
2. Check:
S tire
S front wheel
Damage/wear ! Replace.
Refer to “CHECKING THE TIRES” and
“CHECKING THE WHEELS” in chapter 3.
–19–
FRONT WHEEL AND BRAKE DISCS
CHAS
3. Measure:
S front wheel radial runout 1
S front wheel lateral runout 2
Over the specified limits ! Replace.
Front wheel radial runout limit
1.0 mm (0.04 in)
Front wheel lateral runout limit
0.5 mm (0.02 in)
4. Check:
S collars
Damage/wear ! Replace.
WARNING
S New tires have a relatively low grip on the
road surface until they have been slightly
worn.
Therefore, approximately 100 km (62 mi)
should be traveled at normal speed before
any highspeed riding is done.
5. Check
S wheel bearings
Front wheel turns roughly or is loose ! Replace the wheel bearings.
S oil seals
Damage/wear ! Replace.
6. Replace:
S wheel bearings New
S oil seals New
a. Clean the outside of the front wheel hub.
b. Remove the oil seals 1 with a flat-head
screwdriver.
NOTE:
To prevent damaging the wheel, place a rag between the screwdriver and the wheel surface.
c. Remove the wheel bearings with a general
bearing puller 2 .
d. Install the new wheel bearings and oil seals
in the reverse order of disassembly.
–20–
FRONT WHEEL AND BRAKE DISCS
CHAS
CAUTION:
Do not contact the wheel bearing center race
4 or balls 5 . Contact should be made only
with the outer race 6 .
NOTE:
Use a socket 3 that matches the diameter of
the wheel bearing outer race and oil seal.
EAS00531
CHECKING THE BRAKE DISCS
The following procedure applies to all of the
brake discs.
1. Check:
S brake disc
Damage/galling ! Replace.
2. Measure:
S brake disc deflection 1
Out of specification ! Correct the brake disc
deflection or replace the brake disc.
Brake disc deflection limit
(maximum)
Front: 0.15 mm (0.006 in)
Rear: 0.15 mm (0.006 in)
a. Place the motorcycle on a suitable stand so
that the wheel is elevated.
b. Before measuring the front brake disc deflection, turn the handlebar to the left or right to
ensure that the front wheel is stationary.
c. Remove the brake caliper.
d. Hold the dial gauge at a right angle against
the brake disc surface.
e. Measure the deflection 2 X 3 mm (0.078 X
0.12 in) below the edge of the brake disc.
–21–
FRONT WHEEL AND BRAKE DISCS
CHAS
3. Measure:
S brake disc thickness
Measure the brake disc thickness at a few
different locations.
Out of specification ! Replace.
Brake disc thickness limit
(minimum)
Front: 4.5 mm (0.18 in)
Rear: 5.5 mm (0.22 in)
4. Adjust:
S brake disc deflection
a. Remove the brake disc.
b. Rotate the brake disc by one bolt hole.
c. Install the brake disc.
NOTE:
Tighten the brake disc bolts in stages and in a
crisscross pattern.
Brake disc bolt
23 Nm (2.3 mSkg, 17 ftSlb)
LOCTITE
d. Measure the brake disc deflection.
e. If out of specification, repeat the adjustment
steps until the brake disc deflection is within
specification.
f. If the brake disc deflection cannot be brought
within specification, replace the brake disc.
–22–
CHAS
FRONT WHEEL AND BRAKE DISCS
EAS00544
INSTALLING THE FRONT WHEEL
The following procedure applies to both brake
discs.
1. Lubricate:
S wheel axle
S oil seallips
Recommended lubricant
Lithium soap base grease
2. Install:
S front wheel assembly
NOTE:
The arrow mark a on the tire must point in the
direction of the wheel.
3. Tighten:
59 Nm (5.9 mSkg, 29 ftSlb)
S wheel axle 1
S wheel axle pinch bolt 2
20 Nm (2.0 mSkg, 14 ftSlb)
CAUTION:
Before tightening the wheel axle nut, push
down hard on the handlebar several times and
check if the front fork rebounds smoothly.
4. Install:
S brake calipers
S reflectors
40 Nm (4.0 mSkg, 29 ftSlb)
WARNING
Make sure that the brake hose is routed
properly.
–23–
CHAS
REAR WHEEL AND BRAKE DISC
REAR WHEEL AND BRAKE DISC
MUFFLER AND BRAKE CALIPER
20 Nm (2.0mSkg, 14 ftSlb)
30 Nm (3.0mSkg, 22 ftSlb)
40 Nm (4.0mSkg, 29 ftSlb)
25 Nm (2.5mS kg, 18 ftSlb)
Order
1
2
3
4
Job name/Part name
Removing the muffler and brake
caliper
Muffler
Muffler stay
Brake hose holder
Brake caliper
Q’ty
20 Nm (2.0mSkg, 14 ftSlb)
Remarks
Remove the parts in the order listed.
1
1
1
1
–24–
Refer to “REMOVING THE REAR WHEEL”.
For installation, reverse the removal
procedure.
REAR WHEEL AND BRAKE DISC
CHAS
REAR WHEEL
23 Nm (2.3mSkg, 17 ftSlb)
40 Nm (4.0mSkg, 29 ftSlb)
23 Nm (2.3mSkg, 17 ftSlb)
74 Nm (7.4mSkg, 54 ftSlb)
107 Nm (10.7mSkg, 77 ftSlb)
Order
Job name/Part name
Q’ty
Remarks
Remove the parts in the order listed.
Removing the rear wheel
WARNING
Securely support the motorcycle so
there is no danger of it falling over.
Drain
Refer to “FINAL GEAR OIL REPLACEMENT” in CHAPTER 3.
Refer to “FUEL TANK AND SEATS” in
CHAPTER 3.
Loosen
Final gear oil
Fuel tank and seats
1
2
3
4
5
6
7
Rear fender assembly
Brake caliper bracket bolt
Bolts
Rear axle nut/washer
Rear axle end nuts/axle holder
Rear wheel assembly
Washer
Collar
1
4
1/1
2/1
1
1
1
–25–
Refer to “REMOVING/INSTALLING
THE REAR WHEEL”.
For installation, reverse the removal
procedure.
REAR WHEEL AND BRAKE DISC
CHAS
62 Nm (6.2mSkg, 45 ftSlb)
Order
1
2
3
4
5
6
7
8
Job name/Part name
Rear wheel disassembly
Disassembling the rear wheel
Lock washers
Clutch hub
Dampers
O-rings
Oil seal
Bearing
Spacer
Bearings
Q’ty
Remarks
Remove the parts in the order listed.
2
1
6
2
1
1
1
2
For assembly, reverse the disassembly
procedure.
–26–
REAR WHEEL AND BRAKE DISC
CHAS
EAS00562
REMOVING THE REAR WHEEL
1. Stand the motorcycle on a level surface.
WARNING
Securely support the motorcycle so that
there is no danger of it falling over.
NOTE:
Place the motorcycle on a suitable stand so that
the rear wheel is elevated.
2. Remove:
S rear gear case fitting bolts
3. Remove:
S brake caliper 1
S brake caliper bracket bolt
NOTE:
Do not depress the brake pedal when removing
the brake caliper.
4. Remove:
S wheel axle nut
S washer
5. Remove:
S rear axle end nut 2
6. Remove:
S rear axle holder 3
7. Remove:
S rear wheel
EAS00566
CHECKING THE REAR WHEEL
1. Check:
S wheel axle
S rear wheel
S wheel bearings
S oil seals
Refer to “FRONT WHEEL AND BRAKE
DISCS”.
2. Check:
S tire
Damage/wear ! Replace.
Refer to “CHECKING THE TIRES” in chapter
3.
3. Measure:
S rear wheel radial runout
S rear wheel lateral runout
Refer to “FRONT WHEEL AND BRAKE
DISCS”.
–27–
REAR WHEEL AND BRAKE DISC
CHAS
EAS00567
CHECKING THE REAR WHEEL DRIVE HUB
1. Check:
S rear wheel drive hub
Cracks/damage ! Replace.
S rear wheel drive hub dampers
Damage/wear ! Replace.
EAS00572
INSTALLING THE REAR WHEEL
1. Lubricate:
S drive shaft splines
Recommended lubricant
Molybdenum disulfide grease
2. Lubricate:
S wheel axle
S wheel bearings
S oil seal lips
Recommended lubricant
Lithium soap base grease
3. Install:
S rear wheel assembly
a. Install the rear wheel assembly 1 with the
rear brake caliper bracket 2 and hold the
bracket to keep the specified position.
b. After installation of the rear axle shaft 3 ,
slide the wheel assembly to forward direction.
c. To make sure the caliper bracket mounts on
the swingarm and then, fix the holder of swingarm temporally.
NOTE:
The holder should installed with the punch mark
a facing upper.
d. Tighten the rear gear housing bolts, with specified tightening torque.
Rear gear housing bolt
70 Nm (7.0 mSkg, 51 ftSlb)
e. Tighten the nut of rear axle shaft with specified torque.
Wheel axle nut
107 Nm (10.7 mSkg, 77 ftSlb)
–28–
REAR WHEEL AND BRAKE DISC
CHAS
f. Tighten the rear axle holder with specified
torque.
Rear axle end nut
23 Nm (2.3 mSkg, 17 ftSlb)
g. Tighten the rear brake caliper bracket bolt
with specified tightening torque.
Brake caliper bracket bolt
40 Nm (4.0 mSkg, 29 ftSlb)
h. Install the rear brake caliper on the bracket
and tighten the bolts with specified tightening
torque.
Brake caliper bolt
40 Nm (4.0 mSkg, 29 ftSlb)
–29–
CHECKING THE SWITCHES
ELEC
ELECTRICAL
EAS00731
CHECKING THE SWITCHES
Check each switch for damage or wear, proper connections, and also for continuity between the terminals. Refer to “CHECKING SWITCH CONTINUITY”.
Damage/wear ! Repair or replace the switch.
Improperly connected ! Properly connect.
Incorrect continuity reading ! Replace the switch.
–30–
CHECKING THE SWITCHES
1
2
3
4
5
6
Clutch switch
Horn switch
Dimmer switch
Turn signal switch
Main switch
Front brake switch
7
8
9
10
11
12
Engine stop switch
Start switch
Fuse
Rear brake switch
Sidestand switch
Neutral switch
–31–
ELEC
PRINTED IN U.S.A.
XVS1100AWR(C)/XVS1100ATR(C) WIRING DIAGRAM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Pickup coil
A.C. magneto
Rectifier/ regulator
Main switch
Solenoid
Battery
Main fuse
Starter relay
Starter motor
Starting circuit cut-off relay
Oil level warning light relay
Right handlebar switch
Front brake light switch
Engine stop switch
Start switch
Oil level gauge
Sidestand switch
Fuel pump
Throttle position sensor
Igniter unit
Ignition coil
Spark plug
Speed sensor
Meter assembly
Oil level warning light
Engine trouble warning light
Speedometer
Meter light
Turn signal indicator light
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
Neutral indicator light
High beam indicator light
Neutral switch
Trip switch
Turn signal relay
Horn
Rear brake light switch
Left handlebar switch
Dimmer switch
Horn switch
Clutch switch
Turn signal switch
Headlight
Front turn signal light (left)
Front turn signal light (right)
Rear turn signal light (left)
Rear turn signal light (right)
Tail/ brake light
Ignition fuse
Backup fuse
Headlight fuse
Signal fuse
Carburetor heater fuse
Thermo switch
Carburetor heater 1
Carburetor heater 2
Carburetor heater earth
COLOR CODE
B .........
Br . . . . . . . .
Ch . . . . . . .
Dg . . . . . . .
G ........
Gy . . . . . . .
L .........
Lg . . . . . . . .
O ........
P .........
R.........
Sb . . . . . . . .
W ........
Y .........
B/ L . . . . . . .
B/ R . . . . . .
B/ W . . . . . .
B/ Y . . . . . .
Black
Brown
Chocolate
Dark green
Green
Gray
Blue
Light green
Orange
Pink
Red
Sky blue
White
Yellow
Black/ Blue
Black/ Red
Black/ White
Black/ Yellow
Br/ B . . . . . .
Br/ L . . . . . .
Br/ W . . . . .
Br/ Y . . . . . .
L /B . . . . . . .
L/G . . . . . .
L/R . . . . . .
L/W . . . . . .
L/Y . . . . . . .
R/ B . . . . . .
R/ G . . . . . .
R/ W . . . . . .
R/ Y . . . . . .
Sb/ W . . . . .
W/ B . . . . . .
W/ G . . . . . .
Y/ L . . . . . . .
Y/ R . . . . . .
Brown/ Black
Brown/ Blue
Brown/ White
Brown/ Yellow
Blue/ Black
Blue/ Green
Blue/ Red
Blue/ White
Blue/ Yellow
Red/ Black
Red/ Green
Red/ White
Red/ Yellow
Sky blue / White
White/ Black
White/ Green
Yellow/ Blue
Yellow/ Red