Samsung SDS-P3040 User manual

4 CHANNEL DVR
User Manual
SDS-P3040
4 Channel DVR
User Manual
Copyright
©2012 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or
changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided.
Use of this document and the subsequent results shall be entirely on the user's own responsibility. Samsung Techwin reserves the right to change the
contents of this document without prior notice.
™™Design and specifications are subject to change without prior notice.
™™The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product.
Set password for your wireless network if you use the product with a wireless router. Being not protected with password or using the
default wireless router password may expose your video data to potential threat.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
overview
Important Safety Instructions
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
Read these instructions.
3)
Heed all warnings.
2)
4)
5)
6)
7)
8)
9)
! overview
1)
Keep these instructions.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods
of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
English _3
overview
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within
this unit.
This exclamation point symbol is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or
damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on
top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause fire
or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this
product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted
repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
11. Do not expose the product to the direct airflow from an air conditioner.
Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between
internal and external of the dome camera.
12. If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with
silicon, so that the external air can not flow inside the housing.
Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product
due to a difference between internal and external temperature.
4_ overview
Before Start
Warning
Battery
It is essential that when changing the battery in the unit, the replacement battery must be of the same type
otherwise there may be a possibility of an explosion.
The following are the specifications of the battery you are using now.
• Normal voltage : 3V
CALIFORNIA USA ONLY
• Normal capacity : 170mAh
This Perchlorate warning applies only to primary CR (Manganese Dioxide)
Lithium coin cells in the product sold or distributed ONLY in California USA.
• Continuous standard load : 0.2mA
“Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/
• Operating temperature : - 20°C ~ +85°C
hazardouswaste/perchlorate.”
(-4°F ~ +185°F)
Caution
• Connect the power cord into a grounded outlet.
• The Mains plug is used as a disconnect device and shall stay readily operable at any time.
• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the
Instructions.
System Shutdown
Turning off the power while the product is in operation, or undertaking improper actions may cause damage
or malfunction to the hard drive or the product.
Please right-click to display the context sensitive menu and select <Shutdown>.
After selecting <OK> in the pop-up menu, you can pull off the power cord.
You may want to install a UPS system for safe operation in order to prevent damage caused by an
unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)
English _5
! overview
This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection
to other equipment, menu setup, etc.
You have to keep in mind the following notices :
yy SAMSUNG retains the copyright on this manual.
yy This manual cannot be copied without SAMSUNG’s prior written approval.
yy We are not liable for any or all losses to the product incurred by your use of non-standard product or violation
of instructions mentioned in this manual.
yy Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be
removed from the unit.
yy Before installing an additional HDD or connecting an external storage device (USB memory or USB HDD) to
this DVR, check the compatibility. Consult your provider for the compatibility list.
overview
Operating Temperature
The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).
This product may not work properly if you run right after a long period of storage at a temperature below the
guaranteed one.
Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand
at room temperature for a period.
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).
Likewise, the hard drive may not work at a temperature below the guaranteed one.
Security Precautions
The default password can be exposed to a hacking thread so it is recommended to change the password
after installing the product.
Set password for your wireless network if you use the product with a wireless router. Being not protected with
password or using the default wireless router password may expose your video data to potential threat.
Note that the security and other related issues caused by the unchanged password shall be responsible for
the user.
6_ overview
Contents
overview
connecting with other device
15
live
21
main menu
32
! overview
3
3 Important Safety Instructions
5 Before Start
7Contents
9Features
11 Part Names and Functions (Front)
12 Part Names and Functions (Rear)
13 Remote Control
15Installation
15 Checking the installation environment
16 Connecting the Video, Audio and Monitor
16 Connecting the USB
17 Connecting the Camera (SDC-5340BC)
19 Connecting the RS-485 Device
19 Connecting the Network
21 Getting Started
23 Live Screen Configuration
28 Live Mode
30Zoom
30 Audio On/Off
30Freeze
31 Event Monitoring
32 System Setup
44 Setting the Device
51 Setting the Recording
55 Setting the Event
57Backup
58 Network Configuration
72 Controlling a PTZ Device
English _7
overview
search & play
75
web viewer
80
backup viewer
107
appendix
110
8_ overview
75Search
78Playback
80 Introducing Web Viewer
81 Connecting Web Viewer (Mac)
82 Using Live Viewer (Mac)
83 Connecting Web Viewer (Windows)
84 Using Live Viewer (Windows)
90 Using Search Viewer
94 Viewer Setup
104About
105 Mobile Viewer
107 SEC Backup Viewer
110 Product Specification (Camera)
111 Product Specification (DVR)
113 Default Setting
116Troubleshooting
119 Open Source License Report on the Product
Features
yy Supports CIF(S)/2CIF(M)/4CIF(L) recording formats
yy With the network specific codec, network transfer enabled regardless of the recording conditions
yy De-interlacing processor for better picture quality
yy Display of HDD information and status by using HDD SMART
yy Hard Disk overwrite function
yy Mass storage hard disk backup through high-speed USB 2.0
yy Simultaneous Record and Playback of 4 channel video data
yy Various Search Modes (Search by Time, Event, Backup and Motion Detection)
yy Various Recording Modes (Manual, Event, Scheduled Recording)
yy Alarm Interface
yy Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer
Standards Approvals
equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
MM `` This
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
English _9
! overview
The DVR employs H.264 video encoding for 4 channel inputs and audio encoding for 1 channels while simultaneously
supports hard disc recording and playback.
These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video
and audio data.
yy Provides a convenient User Interface
overview
package Contents
Please unwrap the product, and place the product on a flat place or in the place to be installed.
Please check the following contents are included in addition to the main unit.
package
DIGITAL VIDEO RECORDER
POWER
1
2
3
4
REC
AUDIO IN
NETWORK
DC 12V
Adapter (1EA) / Power Cable (1EA)
Mouse (1EA)
Remote Control (1EA) / Battery (2EA)
SDC-5340BC (4SET)
Camera Cable (4EA)
Camera Power Cable (1EA)
Network Cable (1EA)
Expansion pipe and Screw (12EA)
Manual CD (1EA)
Quick Start Guide (1EA)
Warranty Card (1EA)
DVR (1SET)
1
10_ overview
VIDEO OUT
AUDIO OUT
ALARM IN
2 3 4 G
ALARM OUT
1 COM G
VGA
CONSOLE
USB
pArT nAmeS And funCTionS (fronT)
DIGITAL VIDEO RECORDER
! overview
POWER
REC
a bc
Part Names
a
b
c
USB Port
1
Functions
2
Remote Control
Receiver
3
LED Indicator
4
Connects the USB devices.
AUDIO IN
Input the remote control signal.
NETWORK
DC 12V
1
ALARM IN
2 3 4 G
POWER : Displays the power ON/OFF status.
VIDEO OUT
AUDIO OUT
ALARM OUT
1 COM G
VGA
CONSOLE
USB
REC : Lights on when recording is in progress.
English _11
DIGITAL VIDEO RECORDER
overview
POWER
REC
pArT nAmeS And funCTionS (reAr)
Sdr-3100
a
1
b
c
d
AUDIO IN
2
DC 12V
ALARM IN
2 3 4 G
ALARM OUT
1 COM G
4
VIDEO OUT
AUDIO OUT
j
CONSOLE
USB
VGA
i
Part Names
h
g
Functions
a
b
c
CAMERA IN
AUDIO IN
Audio input signal port (RCA jack, CH1).
d
Ground
e
f
g
h
i
j
NETWORK
` Add a separate earth-grounding cable to use your product safely.
VIDEO OUT
DC 12V
USB
RS-485
VGA
AUDIO OUT
12_ overview
f
NETWORK
1
3
e
Video Signal input ports (BNC type connector).
Video Signal Output Port (RCA jack).
Port to connect a separate earth-grounding cable.
NETWORK connector port.
DVR power input port.
USB connector port.
Used to establish RS-485 communications.
VGA Video Signal Output Port.
Audio Signal Output Port (RCA jack).
MM `` [CONSOLE] is designed for the service repair purpose only.
`` If using the VGA cable, the source from VGA will be displayed as main image on the screen along with the OSD
menus. Then, the BNC port will output the video signal alone.
`` If not using the VGA cable, the source from BNC will be displayed as main image on the screen along with the OSD
Remote Control
SEARCH
BACKUP
Displays the search menu.
Displays the Backup Menu.
MODE
Changes the screen mode.
DVR
Activates the DVR function.
POWER
Displays the Exit pop up screen.
NUMBER [0~+10]
Used as the numeric input keys, or displays a single
channel.
ID
Sets the ID of the system.
Select 2 digits from 0 ~ 9 while pressing the ID Key.
Skip Backward (by unit time),
Slow Rewind, Slow Forward,
Skip Forward (by unit time)
Move Frame
While paused, moves to the previous/next frame.
FR, STOP, PLAY/PAUSE, FF
T/W
Zooms in or out.
SCROLL ,.
Moves the menu scroll.
MENU
RETURN
Goes to the system menu screen.
Returns to the previous screen.
Up/Down/Left/Right($%_ +)/ENTER
AUDIO
Moves the cursor up/down/left/right, and runs the
Select Menu.
Turns Audio on/off.
FREEZE
ALARM
Freezes the screen temporarily.
Cancels the Alarm.
ZOOM
Runs the digital zoom (x2) function.
REC
REC LOCK
Starts or ends the live recording.
Selects the recording lock function.
PIP
Selects or deselects the PIP function.
EP10-000522
EP10-000522
English _13
! overview
menus. If you connect the VGA cable after the system boot, only the video signal from VGA will be displayed.
overview
Using the Numeric buttons
1. Press any button among 1 to 4.
2. Move to the selected channel number.
Changing the Remote Control ID
1. Press the ID button of the remote control and check the ID displayed on the DVR screen.
The factory default ID of the remote control is 00.
2. Enter 2 digits of your selection in order, while pressing the system [ID] button.
3. When ID input is done, press the system [ID] button again to check the setting.
you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed.
MM `` IfRemote
control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 48)
14_ overview
connecting with other device
Installation
Please take note of the followings before using this product.
Checking the installation environment
Samsung Digital Video Recorder (“DVR” hereinafter) is a stateof-art security device, and contains mass storage hard disk(s)
and critical circuits inside.
Temperature
Unit: ºC
One Year: 24HR X 365 DAY =8,760 HR
When the temperature rises inside the product, the product
may breakdown and the product life be shortened.
Life (Unit: HOURS)
English _15
! connecting with other device
yy Do not use the product outdoor.
yy Do not spill water or liquid in the connection part of the product.
yy Do not impose the system to excessive shock or force.
yy Do not pull out the power plug forcefully.
yy Do not disassemble the product on your own.
yy Do not exceed the rated input/output range.
yy Use a certified power cord only.
yy For the product with an input ground, use a grounded power plug.
connecting with other device
ConneCTinG The video, Audio And moniTor
M
` Only one mouse port is available.
AUDI
O IN
VIDEO
OUT
AUDI
ALA
1 2 RM IN
3 4
O OU
T
VGA
ALA
G 1 RM OUT
COM
G
+ -
RS 48
5
NETW
ORK
DC 12
V
CONS
OLE
USB
ConneCTinG The uSB
1. By factory default, a USB port is provided for external connection.
2. You can connect a USB HDD, USB memory or mouse to the USB port.
3. If a USB HDD is connected to the system, recognition and settings are available in “main menu > Setting the
device > Storage device”. (Page 46)
4. This product supports hot-plugging, which connects/removes the USB device during the system operation.
J
` If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.
16_ connecting with other device
ConneCTinG The CAmerA (SdC-5340BC)
a
b
c
d e
Name
a
b
c
d
e
Description
Camera Fitting
Groove
Groove that is used to fit the camera bracket.
There are two grooves; one on the top and one on the bottom.
Lens
Focal length of 3.6mm enables you to cover relatively longer range of monitoring.
IR LED
Illumination Sensor
DVR Connection
Cable
These infrared LED's are controlled by the illumination sensor.
Detects incoming light to control the IR LED.
Connect the cable directly to the DVR without using a particular power cable.
You can use the RJ-45 cable to connect to a remote camera.
English _17
! ConneCTinG wiTh oTher deviCe
Equipped with the IR LED and the illumination sensor, enables you to monitor at night as well as in daytime.
The camera is suitable for both internal and external use.
` Please make sure not to fully expose the camera to rain. The camera must be installed under a shelter to avoid exposure to
excessive rain or moisture.
connecting with other device
Connecting with dvr
AUDIO
VIDEO
OUT
AUDIO
IN
OUT
ALA
1 2 RM IN
3 4
VGA
ALA
G 1 RM OUT
COM
G
+ -
RS 485
NETW
ORK
DC 12
CONS
V
OLE
USB
installing the camera
The camera can be installed on the wall, ceiling, shelf or a desired position using the provided bracket.
1. Select a position where you want to install the camera.
` Make sure the selected position can sustain the weight of the camera.
2. Attach the camera bracket to the wall using the supplied screws.
• SDC-5340BC : (M4X L20).
M4 X L20
sized screws
wall or ceiling
3. Adjust the camera to target the video location and tighten the camera bracket handle on the camera
bracket.
Handle
Handle
4. Connect the camera cable to the camera.
J
` You should be careful when installing the camera outdoors because the cable connectors may be wet with moisture
or pile up with impurities.
` The camera satisfies the IP66 standard, and direct exposure to water or moisture may cause problem such as
condensation.
18_ connecting with other device
ConneCTinG The rS-485 deviCe
Connect the rear [RS-485 +, –] port to the PTZ camera or system keyboard.
` You can connect and control the PTZ camera which supports the RS-485
communication.
+
RS-485
` Check if the RS-485 device is compatible with the product first.
` Pay attention not to change the polarity (+/-) of the RS-485 device when connecting it.
` Depending on camera’s type, connection polarity can be different. For further information, refer to the respective PTZ
Camera’s documentation.
ConneCTinG The neTworK
Connecting to network through ethernet (10/100BaseT)
AUDI
O IN
VIDEO
NETWORK
Hub/Switcher
OUT
AUDI
ALA
1 2 RM IN
3 4
O OU
T
VGA
ALA
G 1 RM OUT
COM
G
+ -
Back Bo
ne
RJ-45 Ethernet Cable
(Direct Cable)
RS 485
NETW
ORK
DC 12
CONS
V
OLE
USB
Hub/Switcher
Windows
Network Viewer
English _19
! ConneCTinG wiTh oTher deviCe
J
connecting with other device
Connecting to the Network using the router
AUDI
O IN
VIDEO
OUT
AUDI
ALA
1 2 RM IN
3 4
O OU
T
VGA
ALA
G 1 RM OUT
COM
G
+ -
xDSL or Cable Modem
RS 48
5
NETW
ORK
DC 12
CONS
V
OLE
USB
Broadband Router
NETWORK
xDSL or Cable Modem
External Remote PC
DDNS Server
(Data Center)
Connecting to Network through ADSL
AUDI
O IN
VIDEO
NETWORK
OUT
AUDI
ALA
1 2 RM IN
3 4
O OU
T
VGA
+ -
RS 48
RJ-45 Ethernet Cable
(Direct Cable)
Phone(A
DSL) Lin
e
Hub/Switcher
Windows
Network Viewer
20_ connecting with other device
ALA
G 1 RM OUT
COM
G
5
NETW
ORK
DC 12
CONS
V
OLE
USB
ADSL MODEM
live
GeTTinG STArTed
Starting the system
M
! Live
1. Connect the power cable of the DVR to the wall outlet.
` It takes about 10 seconds to display the start screen after
booting.
2. You will see the initialization screen.
The initialization process will last about 1 minute.
If a new HDD is installed, the initialization process may
take longer.
3. The live screen appears with a beep.
REC
2012-01-01 01:10:25
2012-01-01
01:10:25
Shutting down the System
You can shut down the system only if you have logged into the DVR.
You require permission to shut down the system if you are not logged in as admin.
1. Press the [power] button on the remote control or
right-click to display the context sensitive menu and select
<Shutdown>.
2. The “Shutdown” confirmation window appears.
3. Use the arrow keys on the remote control to move to
<oK> and press the [enTer] button or click <oK>.
The system will shut down.
4. Disconnecting the power cable for power off and
reconnecting the power cable to restart.
M
2012-01-01 01:10:25
Shutdown
Are you sure to shutdown?
OK
Cancel
2012-01-01
01:10:25
` For the permission management, refer to “Permission Management > Setting Permissions”. (Page 39)
English _21
live
Login
To access a DVR or restricted menu, you should have logged in to the DVR.
1. In live mode, right-click any area of the screen.
You will see the context sensitive menu as in the right
figure.
2012-01-01 01:10:25
Scene Mode 
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Login
2. Click <Login>.
The login dialog appears.
You can also see the login dialog to access a desired
menu by pressing the [menu] button on the remote
control.
` The login dialog will also appear if you press a menu button on
the remote control of the DVR when the corresponding menu
requires logging in.
2012-01-01 01:10:25
Login
 ID
admin
 Password
OK
Cancel
` After logged in, press [RETURN] on the remote control to display
the logout dialog.
` By default, initial ID and password are set to “admin”, and “4321”.
J
` The default password can be exposed to a hacking thread so it is recommended to change the password after
installing the product.
` Set password for your wireless network if you use the product with a wireless router. Being not protected with
password or using the default wireless router password may expose your video data to potential threat.
` Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
M
` For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 39)
Locking All Buttons
This will restrict access to all buttons available in the DVR.
1. In Live mode, press buttons in the order of [STop (@)]
[freeZe][STop (@)][freeZe][menu].
All buttons will be locked.
2. In the lock condition, press any button to display a dialog
where you are prompted to enter the password for
unlocking the buttons.
The button lock will be released if you enter the admin
password.
22_ live
2012-01-01 01:10:25
Key Lock Password
 ID
admin
 Password
OK
Cancel
Live Screen Configuration
Icons on the Live Screen
You can check the status or operation of the DVR with the icons on the live screen.
! live
2012-01-01 00:00:01
CAM 01
Part Names
a
b
Current Date, Time
Login Information
Description
Displays the current time and date.
When you are logged in, the “LOG ON” icon will be displayed.
Displayed if the zoom function is activated.
Freezes the screen temporarily.
c
Screen Mode
Displayed in Auto Sequence mode where all channels are switched at the specific
time interval.
This icon is displayed if a user with restricted access to the Record button tries to
make manual recording.
`` Only the user with the applicable permission can release (stop) the recording.
Displayed if the HDD is full and the DVR has an insufficient space to record.
Displayed if no HDD is installed or the existing HDD should be replaced.
d
System Operation
Displayed if the HDD needs a technical examination.
This will be displayed if the backup operation is in process.
Displayed if a new firmware is found from the network.
e
Video Input Status
Displayed if no input is entered in the condition that the camera is set to <ON>.
Nothing will be displayed on the screen if the camera is set to <OFF>.
English _23
live
Part Names
f
Description
Camera Name/ Channel
Displays the camera name and the changed channel, if any.
Displays the resolution of the recording screen. (Page 53)
Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.
g
Displays AUDIO ON/MUTE.
Camera Operation
Not displayed in video mode if deactivated.
Displayed if a motion detected in the condition that the motion detection is set to
<ON>.
Displays the current record mode from Record/Event/Schedule.
error information
• If the internal HDD is not connected, the “NO HDD”(
) message will appear; if there occurs a problem,
) message in the top left corner. In this case, make sure you contact the
you will see the “HDD FAIL”(
service center for assistance as this may cause a failure of recording, playback or backup.
M
` If you see the NO HDD, HDD FAIL icons on the screen, contact the service center for more details.
Live Screen menu
In addition to the buttons the remote control, you can access a desired menu by right-clicking the mouse any
area in live mode.
The context sensitive menu that appears by right-clicking the screen may differ, depending on the login/
logout, screen split mode and DVR operation mode.
M
` Menu items of Search, Record, Backup, Shutdown can be deactivated, depending on the user permission.
2012-01-01 01:10:25
Scene Mode

2012-01-01 01:10:25
Scene Mode
Audio Off
PTZ Control
Freeze
Zoom In
Stop Alarm
Audio Off
Record
Freeze
Play
Stop Alarm
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout

Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
< Split Mode Menu >
24_ live
< Single Mode Menu >
Split mode menu
The context sensitive menu in split mode differs, depending on the login/logout status.
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
Menu
a
b
c
d
e
f
g
h
i
j
k
l
b
2012-01-01 01:10:25
Scene Mode 
! Live
l
k
j
i
h
g
f
e
d
c
a
Scene Mode
Refer to “Live Mode”. (Page 28)
Freeze
Refer to “Freeze”. (Page 30)
Audio On/Off
Stop Alarm
Record/Stop
Description
Refer to “Audio On/Off ”. (Page 30)
Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 31)
Starts/stops the standard recording.
Play
Refer to “Search & Play > Play”. (Page 78)
Backup
Refer to “Main Menu > Setting the Backup”. (Page 57)
Search
Main Menu
Refer to “Search & Play > Search”. (Page 75)
Accesses the main menu. Refer to the Using the DVR section. (Page 32)
Shutdown
Turns down the DVR.
Login/Logout
You can log in or out.
Show/Hide Launcher
Shows or hides the launcher. Refer to “View the Launcher Menu”. (Page 27)
English _25
live
Single mode menu
The single mode menu is available only in Single Mode.
The context sensitive menu for the One Channel mode, in Split mode is different from that of the Single mode.
2012-01-01 01:10:25
a
b
Full Screen
PTZ Control
Zoom In
Audio On
Freeze
Stop Alarm
Record
Play
Shutdown
Hide Launcher
Logout
Menu
Description
a
Full Screen
Select and click a desired channel in Split mode to switch to the full screen of the selected
channel.
b
Zoom In
Enlarges the selected image. (Page 30)
26_ live
view the Launcher menu
The Launcher menu appears on the bottom of the live screen.
1. In Live mode, right-click to display the context menu and
select <Show Launcher>.
2012-01-01 01:10:25
! Live
2. Move the cursor to the bottom and click a desired item in
the Launcher menu.
M
` If no input is entered for 10 seconds, the menu will disappear.
` The Launcher menu can be accessed only by using the mouse.
2012-01-01
01:10:25
2012-01-01
01:10:25
2012-01-01
01:10:25
2012-01-01
01:10:25
PTZ
2012-01-01
01:10:25
a
b
Alarm Freeze
c d e f g h ij
Menu
Displays the current time and date.
Description
a
Date/Time
b
Screen Mode
c
d
e
Menu Expansion Button
Zoom
Enlarges the selected area. This is available only in Single Live mode.
f
PTZ
g
h
i
j
Alarm
The PTZ control launcher will be active on the Live screen after you select a single channel.
Audio
Freeze
Play
Record
The indication of AM/PM is displayed if you set 12 hours for the time format in “System >
Date/Time/Language > Time”. (Page 32)
Press this button to switch the screen mode in sequence.
The current mode is highlighted in white.
Click to display the hidden menu to the right.
Turns ON/MUTE the sound of the selected channel.
Runs the PTZ Control launcher.
Stops the alarm if it's activated.
Freezes the Live screen temporarily.
Enters Play mode if a file to play exist, and if not, enters Search mode.
Start/End recording the Live screen.
English _27
live
Live Mode
Displays 4 live video images in 3 different modes.
Switching the screen mode
To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in
the context menu.
Press the [MODE] button on the remote control to switch the mode in the sequence of the launcher menu
items.
CH1
CH2
CH2
CH1
CH3
CH2
CH4
CH4
CH3
CH2
CH1
CH1
;
CH1
CH1
CH4
4-split mode
CH4
CH2
CH4
CH3
CH2
CH1
CH1
CH1
CH2
CH3
CH2
CH4
PIP
;
CH1
Switching the screen automatically
CH4
CH3
CH2
You can display 4 live single screens in sequence.
CH3
CH3
CH3
CH1
CH1
CH3
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH2
4
Single mode
CH1
CH2
CH1
Auto Sequence
CH1
CH1
CH1
CH3
CH1
CH2
CH1
CH1
CH1
CH2
CH1
CH2
CH1
CH2
CH1
1
CH1
CH1
CH1
Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be
MM `` Inconducted
at the set interval. (Page 44)
28_ live
CH2
Channel Setting
You can display the channel in a desired area of a split screen.
1. Click a camera name to display a channel list where you can select a different channel.
CH1
CH2
CH3
CH4
;
CH1
CH4
CH2
CH3
CH1
CH1
CH3
CH2
CH2
CH1
Switching to Single Mode
CH1
CH2
When in split mode, select and double-click a desired channel to switch to its Single mode.
CH4
CH2
CH2
Press the
number corresponding
to aCH1desired channel the remote
control to switch
to its Single mode.
CH1
CH3
CH4
Refer to “Remote Control > Using the numeric buttons”. (Page 14)
CH3
CH1 control.
CH1
`` ExCH3: If double-clicking
CH 3 or pressing
the number “3” on the remote
CH1
CH2
CH1
CH1
CH3
CH4
CH2
CH3
CH4
CH2
CH1
CH1
;
CH1
CH1
CH3
CH1
CH1
CH1
CH1
CH2
CH2
CH1
CH1
CH4 CH1
CH2
CH1
CH3
CH1
CH3
CH1
CH2
CH1
CH1
CH1
CH1
CH1
CH1
CH2
CH1
CH1
CH1
CH1
English _29
! live
CH2
2. Select a desired channel and clickCH1it.
The current channel will be switched to the selected one.
Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also
CH1
CH1
CH3
CH4
change the channel position.
`` Ex : if switching CH 1 to CH 4
live
Zoom
This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to
enlarge it twice.
1. Select <Zoom in> in the right-click menu.
Press the [Zoom] button on the remote control, or simply click <
box appears.
> in the launcher menu. The zoom
2. Use the direction keys, or drag and drop to specify an area to enlarge.
3. Press the [enTer] button, or double-click the selected area to enlarge it twice.
` In the enlarged image, use the direction buttons ($%_ +) on the remote controlto move the enlarged area.
4. Press the [Zoom] button on the remote control, or simply click <
the zoom.
2012-01-01 01:10:25
> in the launcher menu to release
2012-01-01 01:10:25
;
Audio on/off
You can turn the sound on/off the CH1 in Live mode.
Audio on/off in Single mode
Click the audio icon (
M
) on the screen, or press the [Audio] button on the remote control to turn it on/off.
` Only the channel where <Audio> is set to <ON> in “Device > Camera” displays the audio icon (
that you can use to turn the sound on/off.
freeZe
This is available only in Live mode, this pauses playing the Live image temporarily.
1. Press the [freeZe] button the remote control, or click <
The playback of the image is stopped temporarily.
2. Press the [freeZe] button again, or click <
This will release the freeze.
30_ live
Freeze
>.
Freeze
> in the launcher menu.
) in Live mode
Event Monitoring
This will display the channel in sync with a specific event (Motion/Video Loss) if it occurs.
In “Monitor > Event Display”, set the event monitoring to ON/OFF and specify the event display time. (Page 49)
• If the second event occurs within the set time of <Event Display>, the first event will last until the second
one is terminated. (Page 49)
`` Ex : If you set <Event Display> to 5 seconds, and only one event occurs in CH 1.
CH2
5 seconds
CH1 CH2
CH1 Event occurrence
CH1
CH3
CH3
CH4
CH4
CH1CH2
CH3
CH1
CH1
Stop alarm
CH2
`` Ex : If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the first
event occurred
in CH 1.
CH1
Event occurrence
CH1
CH1
CH1
CH3
CH2
CH1
4 seconds
9 seconds
CH2
Stop alarm
CH1
CH3
CH1
CH2
CH1
CH1
CH1
MM `` Press the [ALARM] button to reset the alarm settings and to release the event mode.
CH1
`` If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will
be performed.
CH1
CH2
English _31
! live
• If multiple events occur simultaneously, the screen will switch to a split mode.
- 2~4 events : 4-split mode
main menu
You can setup the system properties, devices, and options for recording, event,
backup and network.
SYSTem SeTuP
You can setup Date/Time/Language, Permission, System Properties and Log.
Date/Time/Language
You can check and setup the current Date/Time and time related properties, as well as the language used for
the interface on the screen.
Setting the Date/Time/Language
Set the Date/Time/Language
Using the mouse may help make setup easier.
1. Press the [menu] button on the remote control.
` If not logged in, it prompts with login window.
Refer to “Login”. (Page 22)
2012-01-01 01:10:25
2012-01-01
01:10:25
2. Use the left/right buttons (_ +) to select the <System>.
System property setup menu is selected.
3. Use the up/down buttons ($%) to select <Date/Time/
Language> and press the [enTeR] button.
4. Select <Date/Time/Language>.
A dialog to setup Date, Time and Language.
5. Use direction buttons ($%_ +) to select an item to set
and make your changes.
32_ main menu
Logout
System
Date/Time/Language
Permission Management
System Management
Log Information
Return
Date/Time/Language
Date/Time/Language
Holiday
 Date
2012-01-01
YYYY-MM-DD
 Time
08:14:24
24 Hours
 Time Zone
GMT+09:00
 Time Sync.
 DST
 Language
Setup
Dec First (Sun) 0
Dec First (Sun) 0
English
OK
Cancel
• Time Sync. : You can set the DVR’s current time
> regularly if you select to use <Time Server
synchronized to a selected <Time Server>
Server>.
In this case, <Date/Time/Language> setup does not allow time adjustment.
- Time Server : Enter an IP or URL address of the time
server.
- Last Sync Time : Displays the most recent synchronization
time from the selected time server.
Date/Time/Language
Date/Time/Language
 Date
Time
Holiday
2012 -01-01
Synchronization
YYYY-MM-DD
Setup
Use
 Synchronization
08:14:24
24 Hours
 Time
203.248.240.103
 Time Server
GMT+08:00
 Time Zone
Fail
 Last Sync Time
Setup
Not Used
 Time Sync.
Use
 Activate as Server
Dec First (Sun) 0H
Dec First (Sun) 0H
 DST
- Activate as Server : Set to <Use> to allow the DVR to act
as a Time Server for other DVRs.
• DST : Set up Daylight Saving Time with its period to make
the time earlier than the GMT of its time zone by 1 hour
during the set period.
• Language : Select your language. Sets the language for the
interface.
English, French, German, Spanish, Italian, Chinese, Russian, Korean, Polish, Japanese, Dutch, Portuguese,
Turkish, Czech, Danish, Swedish, Thai, Romanian, Serbian, Croatian, Hungarian and Greek are available.
 Language
OK
Cancel
OK
Cancel
English
6. When the Date/Time/Language setup is done, press <OK>.
M
` You can also use numeric buttons on the remote control to enter values for Date, Time and other numeric fields.
English _33
! main menu
• Date : Sets the date that will appear on the screen.
You can select the date format.
• Time : Sets the time and its format that will appear on the
screen.
Select either one from <24 Hours, 12 Hours (am/Pm)>.
• Time Zone : Sets the time zone of your area based on the
Greenwich Mean Time (GMT).
` GMT (Greenwich Mean Time) is standard World Time and the basis
of world time zone.
main menu
Setting Holiday
You can set specific dates to Holidays according to your preferences.
Holidays are applied to <Recording Schedule> and <alarm Schedule> too.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Date/Time/Language> window to select <Date/Time/Language>, and
press the [enTeR] button.
2. Select <Holiday>.
A calendar for Holiday setup appears.
> buttons to select year or month,
3. Use the left/right <
and press the [enTeR] button.
Date/Time/Language
Holiday
Date/Time/Language
2012
Jan
Sun
1
Mon
2
Tue
3
Wed
4
Thu
5
Fri
6
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Sat
7
OK
4. Use direction buttons ($%_ +) to select a desired date,
and press the [enTeR] button.
You will see the “Setting Holiday” screen.
` Ex : Select January 9th and check on <1/9> only to make every
January 9th a holiday. Check both on <1/9> and
<Jan 2nd Mon> to make every January 9th and 2nd Monday
of January holidays.
5. When the Holiday setup is done, press <OK>.
Sat
7
Cancel
Date/Time/Language
Holiday
Date/Time/Language
2012
Jan
Setting
Sun Holiday
Mon Tue
3
Wed
4
Thu
5
Fri
6
10
11
12
13
14
17
18
19
20
21
25
27
28
1
2
8
9
15
16
22
23
OK
24
29
30
31
1/9
Jan 2nd Mon
OK
Cancel
26
Cancel
using the Calendar
Using the mouse may help make setup easier.
Select year and month.
Select the left/right <
> key on the left/right side of year/month and press [enTeR] button to
adjust by 1 year/month.
Use direction buttons to select a date and press [enTeR] button.
` A date with recorded data to be searched will appear in yellow in the System Log, Event Log, Time Search and
Event Search.
34_ main menu
Permission management
You can set permissions of each user over the DVR's specific function and settings.
! main menu
Setting the administrator
You can set and change Administrator’s ID and password.
The administrator can use and set all menu items and functions.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <System> window to
move to <Permission management>, and press
[enTeR] button.
2. Select <admin>.
A dialog for Admin ID and Password input appears.
Permission Management
Admin
Group
User
 ID
admin
 New Password
************
 Confirm P/W
************
Setup
3. Use direction buttons ($%_ +) to move to a desired
item, and set the ID and password.
M
` By default, initial ID and password are set to “admin”, and
OK
“4321”.
Cancel
` The default password can be exposed to a hacking thread so it is recommended to change the password after
installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
4. When the administrator setup is done, press <OK>.
using Virtual Keyboard
For alphanumeric inputs, the virtual keyboard window
appears.
Use direction buttons ($%_ +) to move to a desired
character, and press the [enTeR] button.
In the upper text input box of the virtual keyboard, there
displays a list of candidate words containing the selected
character.
`
1
2
3
4
5
6
7
8
9
0
-
=

q
w
e
r
t
y
u
i
o
p
[
]
\
Del
a
s
d
f
g
h
j
k
l
;
‘
Caps Lock
z
x
c
v
b
n
m
,
.
/
Space
OK
Shift
Ctrl
Cancel
Select a word from the list, or use the keyboard to enter the
whole word.
` If there are many of candidate words, use < , > buttons to move between them forward and backward.
Select <OK>.
Entered word is applied.
` For upper case letters, use <Caps Lock> button.
`
`
`
`
`
For special characters, use <Shift> button.
Using the virtual keyboard is the same to a normal keyboard use in your region.
You can enter the ID with case-insensitive alphanumeric characters only.
For the password, use alphabets and special characters excluding < \ > and <“>.
You can use number buttons on the remote control.
English _35
main menu
Setting the Group
You can create user groups and setup permissions for those user groups.
You can register a user for each group in <user>.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <System> window to
move to <Permission management>, and press
[enTeR] button.
2. Select <Group>.
A window for <add>, <Delete>, <Rename>, and
<Group authority> setup appears.
Permission Management
Group
Admin
User
 Group
Add
Setup
Delete
Rename
 Group Authority
Live View
Setup
Search
Setup
Backup
Setup
3. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Add, Delete, Rename : You can add, delete, rename a
group or modify the permissions given to the group.
The virtual keyboard appears when <add> or <Rename> was selected.
OK
Cancel
- Add : When you first run the DVR with the admin account, only the admin account exists. Add has already
been deactivated. Select to display the virtual keyboard. Enter a group name. You can add up to 10
groups.
- Delete : Deletes a user group that is already registered. Selecting Delete will delete all user accounts
belonging to that group.
- Rename : Renames a group that is already registered. Select <Rename> to display the virtual keyboard.
` For entering a group name, refer to “Using Virtual Keyboard”. (Page 35)
• Group Authority : Sets permissions to access menu items of each group.
Users of a group can access checked functions.
4. When the group setup is done, press <OK>.
To set the group authority
You can set the permissions of the group users to access the menu according to the channel.
1. Select a menu to which the group permission is assigned.
The menu where the group permission is assigned will be
displayed in the Live menu when a group user logs in.
• Live View : You can set the permission to access the Live
screen according to the channel.
• Search : You can set the permission to access the Search
menu according to the channel.
• Backup : You can set the permission to access the Backup
menu according to the channel.
Permission Management
Group
Admin
 Group
Add
 Group Authority
Channel
Live View
Search
Backup
All
1
Setup
Delete
Setup
Setup
Setup
Setup
2. Select <OK>.
Select and assign a group user so that the user can access the specified menu.
36_ main menu
User
ABC
2
OK
OK
3
Cancel
Cancel
4
Rename
To restrict the user permissions
If the admin restricts all permissions of an added group, the users belonging to that group can access only
the default minimum menus and can change the user’s own password only.
2. Log in with a registered user ID.
! main menu
1. Start the DVR.
If all permissions are restricted, only the Login dialog
should appear.
Login
 ID
abc
 Password
OK
3. Right-click any area on the screen.
If all permissions are restricted, only the accessible context
menus should appear.
Cancel
2012-01-01 01:10:25
Scene Mode

Audio Off
Freeze
Stop Alarm
User Menu
Hide Launcher
Logout
2012-01-01
01:10:25
To change the user password
If you log in with a user account that is restricted to access the menu, you can change your own password
only.
1. Log in with your account.
2. Select <user menu>.
The Permission Management setup screen appears.
3. Select <Permission management>.
The Password setup dialog appears.
Permission Management
User
 ID
abc
 New Password
************
 Confirm P/W
************
4. Enter a new password.
5. Select <OK>.
You change to the password will be applied.
OK
Cancel
English _37
main menu
Setting the user
Users can be added only if a group was created in <Group> menu.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <System> window to
move to <Permission management>, and press
[enTeR] button.
2. Select <user>.
A window for Add User appears.
3. Use direction buttons ($%_ +) to select <add> from the
window.
A window for “add user” appears.
You can configure the Network Viewer settings including
name, ID, viewer, Select Group and password.
Result of the user setup appears in the <user> window.
To change the user property, use “edit user”.
The “edit user” window appears when you select a
desired item to be changed in the <user> window.
• Viewer : If you select <use>, you will be given access to the
Web Viewer and Network Viewer.
` Refer to “Connecting Web Viewer”. (Page 81)
` For more information about use of Smartviewer, refer to the
Smartviewer's user guide.
4. When the user setup is done, press <OK>.
38_ main menu
Permission Management
Admin
 Group
User
Group
Setup
All Group
Group
Add
Name
ID
Viewer
Del
Previous/Next Page
OK
Cancel
Permission Management
Admin
 Group
User
Group
Setup
Add
User
All Group
Group  Name
Add
Name
ID
Viewer
Del
 ID
 Viewer
Not Used
 Select Group
ABC
 Password
 Confirm P/W
OK
Cancel
Previous/Next Page
OK
Cancel
Setting Permissions
You can set restricted access for all general users.
Items with restrictions will require logging in for use.
Using the mouse may help make setup easier.
2. Select <Setup>.
The Restricted Access, Restriction on Network Access,
Auto Log out, Manual Input of ID setup screen appear.
3. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Restricted Access : All menu items allowed for a user can
be set with restricted access.
- Checked (
Permission Management
Admin
Group
User
Setup
 Restricted Access
Live View
Backup
All
 Restriction on Network Access
All Network
Web Viewer
 Auto Log out
OFF
 Manual Input of ID
ON
OK
Cancel
) : Restricted
- Not checked ( ) : Accessible
` If it is not checked ( ) in <Restricted Access>, any user can access the item no matter what the <Group Authority>
setting.
) in <Restricted Access>, a user can access the item only if the user has permission in <Group
Authority> setting.
` If it is checked (
• Restriction on Network Access : Restricts remote access from a <Restricted access> network.
- All Network : Restricts all access instances via Network Viewer and Web Viewer.
- Web Viewer : Restricts access via the Web Viewer.
• Auto Log out : A user will be automatically logged out if there is no operation on DVR for over set period of
time.
• Manual Input of ID : Prompts you to enter the user ID
manually for the login process.
- Checked ( ) : Encloses the registered user IDs with the
[] symbols.
Use the virtual keyboard to enter the user ID.
4. When the permission setup is done, press <OK>.
Login
 ID
*****
 Password
OK
Cancel
English _39
! main menu
1. Use the up/down buttons ($%) in <System> window to
move to <Permission management>, and press
[enTeR] button.
main menu
System management
You can check the system version, update to a newer version, as well as data backup and initialization.
Checking the System information
You can check the current system version, broadcasting system, MAC address. You can update the system.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <System> window to
move to <System management>, and press [enTeR]
button.
2. Check the Software Version, Broadcast Format and MAC
Address.
• System Information : Shows the current system’s
information.
The values can not be changed by a user.
• S/W Upgrade : Updates the DVR’s software.
` Ex : If you connect to a storage device that has upgradable software
installed, and return to the <System Management> menu, the
current software version will be displayed.
System Management
System Information
Settings
 System Information
 Software Version
v1.0xh_yymmddhhmmss
 Broadcast Format
NTSC
 MAC Address
00:00:F0:54:FF:FF
 S/W Upgrade
Upgrade
 Device
No Device
 Version
No S/W Data
Previous
System Management
System Information
Settings
 System Information
 Software Version
v1.0xh_yymmddhhmmss
 Broadcast Format
NTSC
 MAC Address
00:00:F0:54:FF:FF
 S/W Upgrade
 Device
USB2FlashStorage
 Version
v1.0xh_yymmddhhmmss
Upgrade
Previous
• updating the Software
1. Connect a device storing the software to be updated.
(It may take about 10 seconds to recognize the device.)
` Upgradeable devices include USB memory and network device.
` To update the network, the current DVR should have been
connected to the network.
Upgrade via the proxy server may not be enabled due to the
restricted access.
2. Select <System management> from <System> window.
3. Select <System information>.
System Management
System Information
Settings
 System Information
 Software Version
System
Format
 Broadcast
v1.0xh_yymmddhhmmss
Upgrade
NTSC
 MAC Address
Current Version 00:00:F0:54:FF:FF
v1.0xh_yymmddhhmmss
New Version
v1.0xh_yymmddhhmmss
 S/W Upgrade
Do you want to upgrade?
Upgrade
USB2FlashStorage
 Device
OK
Cancel
V1.08_090731170402
 Version
Previous
4. When the recognized device appears, select <upgrade>.
` The <Upgrade> button will be activated only if the current <Software Version> of the <System Information> is
same to or older than that of <S/W Upgrade>.
40_ main menu
5. Press <OK> in the “System upgrade” window.
` While updating, it shows the progress.
• Updating progresses with 3 steps as shown in the figure.
System Management
System Information
Settings
 System Information
 Software Version
v1.0xh_yymmddhhmmss
Format
 BroadcastS/W
NTSC
Upgrade
 MAC Address
00:00:F0:54:FF:FF
Software upgrading...
 Device
USB2FlashStorage
 Version
V1.08_090731170402
Upgrade
Previous
System Management
System Information
Settings
 System Information
 Software Version
v1.0xh_yymmddhhmmss
FormatUpgrade
 BroadcastS/W
NTSC
 MAC Address
00:00:F0:54:FF:FF
Software upgrading...
Software upgrading...
 S/W Upgrade
 Device
 Version
Do not turn off during the upgrade.
Upgrade
USB2FlashStorage
V1.08_090731170402
Previous
6. When the updating is done, it automatically restarts.
Do not turn the power off until it finishes restarting.
M
` If “Upgrade Failed” appears, retry from the step 4.
When you experience continued failure, consult the service
center for assistance.
` When you perform S/W update remotely using Smart Viewer,
it may take a max of 3 minutes to complete the update since
Smart Viewer popped up a confirmation message. This is to
guarantee that the DVR set operates stably. For a faster
update, use the USB cable to connect to the DVR set.
English _41
! main menu
 S/W Upgrade
main menu
Settings
You can copy and import the DVR settings by using a storage media.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <System> window to
move to <System management>, and press [enTeR]
buttBon.
2. Select <Settings>.
A window of storage device and load factory default
appears.
System Management
Settings
System Information
 Storage Device
0 MB (Remained Capacity)
 DVRUSB
10041400
Export
 USBDVR
No data
Import
Include Network Settings
 Load Factory Default
3. Use direction buttons ($%_ +) to move to a desired
item, and export or import settings data to a storage
device.
• Storage Device : Shows the connected storage device.
• Export : Exports DVR settings to the connected storage device.
• Import : Imports DVR settings from the storage device and applies to the DVR.
` If <Include Network Settings> is checked, the network settings will be imported too.
• Load Factory Default : If <Default> is selected, a
confirmation dialog for “Load Factory Default” prompts.
Press <OK> toTo move to the previous menu, press
<Previous>.
Default
Previous
System Management
Settings
System Information
 Storage Device
Load
 DVRUSB
 USBDVR
Factory
Default
10041400
0 MB (Remained Capacity)
Export
Import
No data
to Default
Setting?
IncludeSure
Network
Settings
OK
Default
 Load Factory Default
Cancel
Previous
Log information
You can browse logs on the system and events.
System Log
System Log shows log and timestamp on every system start up, system shutdown, and changes on system
settings.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <System> window to
move to <Log information>, and press [enTeR] button.
2. Select <System Log>.
` Refer to “Using the Calendar”. (Page 34)
Click on the calendar < > to display the calendar window.
Log Information
System Log
Search Day
First Page
No.
Event Log
2012-01-01
Backup Log
Search
Last Page
Type
Log List
• Type : When there are too many logs, you can display logs
of the desired format by selecting the type.
3. Use direction buttons ($%_ +) to move to a desired
item, and press <Search>.
42_ main menu
View all
Date/Time
Previous/Next Page
Previous
event Log
Event log shows recorded events on alarms, motion detections and video loss.
It also shows the log and its timestamp.
Using the mouse may help make setup easier.
2. Select <event Log>.
3. Use direction buttons ($%_ +) to move to the desired
item.
4. Set Search Day, Channel and Type and the press
<Search>.
` Refer to “Using the Calendar”. (Page 34)
Click on the calendar < > to display the calendar window.
Log Information
System Log
Search Day
First Page
Event Log
Backup Log
Search
2012-01-01
Last Page
CH
All CHs
Type
View all
No.
Log List
Date/Time
7
Motion Detection [CH 1]
2012-01-01 00:02:14
6
Motion Detection [CH 2]
2012-01-01 00:02:14
5
Motion Detection [CH 3]
2012-01-01 00:02:14
4
Motion Detection [CH 4]
2012-01-01 00:02:18
3
Motion Detection [CH 3]
2012-01-01 00:02:18
2
Motion Detection [CH 2]
2012-01-01 00:02:18
1
Motion Detection [CH 1]
2012-01-01 00:02:18
Previous/Next Page
Previous
Backup Log
You can find out who backed up and the details (backup time, channel, device to use, file format, etc.).
Using the mouse may help make setup easier.
1. In the <System> window, press the up/down ($%) button
to move to <Log information> and press the [enTeR]
button.
2. Select <Backup Log>.
Log Information
System Log
Search Day
First Page
No.
Backup Log
Event Log
2012-01-01
~
Last Page
Search
2012-01-02
Previous/Next Page
User
Date/Time
3. Use the four direction buttons ($%_ +) to move to a
desired item.
4. Specify a search term and select <Search> in the right
corner.
Backup details for the search term will be listed.
Previous
English _43
! main menu
1. Use the up/down buttons ($%) in <System> window to
move to <Log information>, and press [enTeR] button.
main menu
SeTTinG THe DeViCe
You can setup Camera, Storage Device, Remote Device and Monitor.
Camera
Setting the Camera
You can set Video, Audio, Channel Name and Dwell Time of a Camera.
Using the mouse may help make setup easier.
1. Press Bthe [menu] button on the remote control.
2. Use the left/right button (_ +) to select <Device>.
Device setting menu is selected.
Logout
3. Use the up/down buttons ($%) to move to <Camera>,
and press [enTeR] button.
Return
Device
Camera
Storage Device
Remote Device
Monitor
4. Select <Camera>.
You will see a window where you can configure the
camera settings including Video, Audio, CH Name,
SEQ-Dwell Time.
5. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Video
- <On/OFF> : You can turn ON/OFF the selected channel’s
camera.
Camera
Camera
PTZ
CH
Video 
CH Name
SEQ-Dwell Time 
1
ON

ON

CAM 01
5 sec

2
ON

OFF

CAM 02
5 sec

3
ON

OFF

CAM 03
5 sec

4
ON

OFF

CAM 04
5 sec

Screen Setup
Audio 
Privacy Region
OK
Cancel
- <Covert1> : Shows information other than the video of
the selected channel.
` For privacy protection, it does not display the video while the recording continues.
- <Covert2> : Shows nothing but an empty screen while the recording continues.
• Audio
- If set to <On>, you can turn the audio of the channel ON/OFF on the Live screen.
- If set to <OFF>, the channel’s audio is off on the Live screen and not recorded.
` Audio output is available for only CH1.
• CH Name : Up to 15 characters including blanks are allowed. (The first character should not be empty.)
` Refer to “Using Virtual Keyboard”. (Page 35)
• SEQ-Dwell Time : You can set the dwell time between channels for the Live screen.
` If set to <OFF>, the channel is not listed in the Auto Sequence mode.
44_ main menu
• Privacy Region : You can specify a certain area of the
camera video to be protected for your privacy.
Screen Setup
CH1
50
50
6. When the camera setup is done, press <OK>.
Init
50
OK
Apply to All CH
Cancel
To set the privacy region
Select <Privacy Region>.
When “Privacy Region” window appears, select a
channel for detection and set the area of motion
detection.
• To set the area in “Privacy Region” window
In the “Privacy Region” window, select desired region
from <
>.
• Privacy Region
Privacy Region
CH1
Privacy Region1
You can specify up to 4 privacy zones for each channel,
which can be identified by the color.
1
Purple 2
Green 3
Blue 4
Individual
OK
Apply to All CH
Cancel
Yellow
• To set the area using <individual> selection
When selected <individual>, “Privacy Region” window disappears and you can select cells one by
one.
When the motion area setup is done, Right-click to select <menu> in the context menu or the [menu]
button on the remote control to display the “Privacy Region” window again.
- Clear All : Selected cell is removed from the Privacy Region.
Clear All
- Menu : After selecting individual motion areas, move to the “Privacy Region”
Menu
window.
` If selected <Apply to All CH>, selected motion area is applied to all channels.
When completing the privacy zone settings, click <OK>.
English _45
! main menu
• Screen Setup : The video appeared on the screen may vary
depending on the channel’s camera, configure the DVR
display to your preferences.
Select a channel and adjust the < (Brightness)>,
< (Contrast)>, and < (Color)> of the selected channel.
` Press the <Init> to initialize settings back to the default 50.
main menu
Setting the PTZ
To use Camera’s PTZ functions, ID and protocols of each camera and DVR should be matched.
For other settings, refer to the “Remote Devices” settings. (Page 48)
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Device> window to
move to <Camera>, and press [enTeR] button.
2. Select <PTZ>.
A window of PTZ settings appears.
Camera
PTZ
Camera
CH
ID
1
0
>
None

2
1
>
Protocol 
None

3
2
>
None

4
3
>
None

3. Use direction buttons ($%_ +) to move to a desired
item, and select it.
• ID : Set the ID of the connected camera of each channel.
You can easily setup by using the numeric buttons on the
remote control.
OK
Cancel
• Protocol : Set the protocol of the connected camera of each channel.
M
` You can check the camera’s ID and protocol if you turn the camera off and on after connecting it to the DVR.
4. When the PTZ setup is done, press <OK>.
Storage Device
You can check information on storage devices.
Confirming Devices
You can check storage devices and their free space, usage as well as status.
Devices available are HDD, and USB devices (Memory, HDD).
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Device> window to
move to <Storage Device>, and press [enTeR] button.
2. Select <Device>.
• No. : Shows the assigned number of the internal HDD.
• Used/Total : Shows the used/total capacity of the storage
device.
• Used : Sets the storage device’s usage.
- USB memory is used for backup purpose only.
• Status/Management : Shows the current status of the HDD,
as in Normal/Check/Replace.
- Normal : Available to use
- Check : Available to use but recommended to replace
- Replace : Requires immediate replacement.
3. To move to the previous menu, press <OK>.
46_ main menu
Storage Device
Format
Device
Device
HDD
HDD Alarm
Select
1
Used/Total
Used
12.28G/499.37G
Internal
Format
OK
Cancel
Formatting
You can format a storage device.
Using the mouse may help make setup easier.
2. Select <Format>.
A window for selection of device for formatting appears.
Storage Device
Format
Device
Device
HDD Alarm
Select
HDD
1
Used/Total
Used
12.28G/499.37G
Internal
Manage
3. Use direction buttons ($%_ +) to select a device to be
formatted.
Formatting deletes all recordings.
Proceed formatting?
OK
Cancel
Format
OK
4. Select <Format> on the bottom of the screen.
Press <OK> on the “manage” confirmation window will
start formatting the selected device.
5. When the formatting is done, press <OK>.
M
Cancel
Storage Device
Device
Format
HDD Alarm
Device
No.
Used/Total
Used
Status/Management
HDD
1
12.28G/499.37G
Internal
Normal
` Even when formatted, used HDD space will not be 0 GB due
to the space reserved by the system required for operating.
HDD Map
OK
Cancel
English _47
! main menu
1. Use the up/down buttons ($%) in <Device> window to
move to <Storage Device>, and press [enTeR] button.
main menu
HDD alarm
You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port,
and its duration.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Device> window to
move to <Storage Device>, and press [enTeR] button.
2. Select <HDD alarm>.
A window for setting HDD check and replace output ports
and their durations appears.
3. Use direction buttons ($%_ +) to move to the desired
item.
• Alarm
Storage Device
Device
HDD Alarm
Format
BEEP
 Check Alarm Output Port
 Duration
OFF
 Replace Alarm Output Port
 Duration
BEEP
OFF
- If <BeeP> was selected, a beep will sound.
• Check Alarm Output Port : If HDD generates check alarm,
the alarm signal will output to the specified alarm output port.
• Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specified
alarm output port.
• Duration : Sets the alarm duration for the alarm signal and beep sound.
M
OK
Cancel
` <Check> status means that the HDD is operating but it has problems that require technical examination.
(
) appears on the Live screen.
(
) appears on the Live screen.
` <Replace> status means that the HDD has defect and requires immediate replacement.
4. When the HDD Alarm setup is done, press <OK>.
Remote Devices
You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Device> window to
move to <Remote Device>, and press [enTeR] button.
2. Use direction buttons ($%_ +) to move to the desired
item, and press [enTeR] button.
3. Set the values of each communication setup of the remote
device.
• Baudrate : Baud rate settings of the DVR, PTZ camera and
system keyboard should be matched for proper operations.
4. Specify the system keyboard and remote control ID, and
click <OK>.
M
Remote Device
Baudrate
9600
Parity

None
Data
8

Stop Bit
1

System Keyboard
OFF
ID
1
Remote Control
ON
ID
0
OK
Cancel
` For changing the remote control’s ID, refer to “Changing the Remote Control ID”. (Page 14)
48_ main menu
Transfer type

Half Duplex
monitor
You can select which item(s) to be displayed on the screen.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Device> window to
move to <monitor>, and press [enTeR] button.
2. Select <monitor>.
3. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Event Display : Sets the dwell time of the event channel
display on the monitor when an event occurs.
If selected <Continuous>, it displays the channel until you
press [aLaRm] button to release it.
• Display : Displays only checked items on the monitor
screen.
• Video Out: You can set the video output mode.
Monitor
Monitor
Mode
 Event Display
OFF
 Display
Date
 Video Output
Time
CH Name
Icon
VGA
Display Position Setup
OK
Cancel
- Auto : The default is set to Composite. (In VGA mode, the “SAMSUNG” logo will be displayed)
If a VGA source is connected, the source from the VGA will be displayed as main. (In Composite mode,
the spot screen will be displayed)
The monitor distributor is not supported.
To switch to VGA mode, turn off the DVR set and connect the VGA jack. (The VGA monitor will turn on)
- VGA : The main video mode will switch to VGA after the DVR set reboots; the composite source will be
displayed on the spot screen.
- Composite : The main video mode will switch to Composite after the DVR set reboots. In VGA mode, the
“SAMSUNG” logo will be displayed.
4. When the monitor setup is done, press <OK>.
Setting Display position
Some monitors many not display information (camera name, icon, time information, etc.) about the DVR,
depending on the condition. Then, you can change the display position of the data.
1. In the <Device> window, press the up/down ($%) button
to move to <monitor> and press the [enTeR] button.
2. Select the <monitor> item.
3. Select <Display Position Setup> in the bottom.
You will move to the <Display Position Setup> window.
4. Use the four direction buttons or the number buttons on
the remote control to adjust the data position.
2012-01-01 01:10:25
Display Position Setup
30
30
30
30
OK
Cancel
CAM 03
English _49
! main menu
Setting the monitor
main menu
Setting the Screen mode
You can configure the Live screen and Split Screens.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Device> window to
move to <monitor>, and press [enTeR] button.
2. Select <mode>.
3. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Live Screen : Select split modes for the Live screen.
4-split screens are included by default.
• Play Screen : Select split modes for the playback screen.
Single screen and 4-split screen are provided by default.
4. When the screen mode setup is done, press <OK>.
50_ main menu
Monitor
Monitor
Mode
Live Screen
Play Screen
Live
OK
Cancel
Play
SeTTinG THe ReCORDinG
You can setup scheduled recording, event recording and other recording related settings.
Make your reservation on a date and time to schedule the recording on specified time.
Using the mouse may help make setup easier.
1. Press the [menu] button on the remote control.
2. Use the left/right button (_ +) to select <Record>.
Record menu is selected.
Logout
3. Use the up/down buttons ($%) to move to <Recording
Schedule>, and press [enTeR] button.
Return
Record
Recording Schedule
Event Record Duration
REC Quality & Resolution
Record Option
4. Select <Recording Schedule>.
A window of scheduled recording setup appears.
5. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
Recording Schedule
CH1
All
0 1 2 3 4
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
Mon
Tue
Wed
Thu
Fri
Sat
Hol
No Recording
Continuous
Apply to All CH
Event
Both(Cont&Evnt)
OK
• Apply to All CH : If selected <apply to all CH>, “apply to
all CH” window appears.
Press <OK> to apply the setup to all channels.
6. When the recording schedule setup is done, press <OK>.
M
` Event recording and scheduled recording starts about 3
seconds prior to the event/schedule for guaranteed recording.
Cancel
Recording Schedule
CH1
All
Sun
Mon
0 1 2 3 4
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Apply to All CH
Tue
Wed
Thu
Apply recording schedule to all channels?
Fri
OK
Sat
Cancel
Hol
No Recording
Continuous
Apply to All CH
Event
Both(Cont&Evnt)
OK
Cancel
English _51
! main menu
Recording Schedule
main menu
Recording Color Tags
Color
Function
White
No Recording
Blue
Event
Orange
Green
Continuous
Both(Cont&Evnt)
Description
No schedule / event recording
Scheduled recording only
Event recording only
Both scheduled / event recordings
Each press of a selected cell will cycle through <no Recording>-<Continuous>-<event><Both(Cont&evnt)>.
event Record Duration
You can set the beginning and ending point of a recording on an event.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Record> window to
move to <event Record Duration>, and press [enTeR]
button.
Event Record Duration
CH
52_ main menu
POST Event 
OFF

OFF

1 min

3
OFF

1 min

4
OFF

1 min

2. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Pre Event : The recording of an event will start at a
pre-determined time prior to the actual occurrence of the event.
If it is set to 5 seconds, the recording begins from 5
seconds before the event.
• POST Event : The recording will continue for a
pre-determined time after the actual end of an event.
If it is set to 5 seconds, the recording ends in 5 seconds after an event.
3. When the event recording duration setup is done, press <OK>.
Pre Event 
1
2
OK
1 min
Cancel

ReC Quality / Resolution
You can set resolution, fps and quality of recordings by channel, and by recording type of standard / event.
! main menu
Setting Standard Recording Properties
You can set each channel’s resolution, quality and fps for normal recordings.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Record> window to
move to <ReC Quality & Resolution>, and press
[enTeR] button.
2. Select <Standard>.
3. When the recording setup is done, press <OK>.
REC Quality & Resolution
Standard
Event
Remaining count : 4CIF(L) : 2
CH
2CIF(M) : 4
Resolution 
CIF(S) : 8
Record Rate 
Record Quality 
1
CIF(S)

7fps

Level4

2
CIF(S)

7fps

Level4

3
CIF(S)

7fps

Level4

4
CIF(S)

7fps

Level4

OK
Cancel
Setting event Recording Properties
You can set each channel’s resolution, quality and fps for event recordings.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Record> window to
move to <ReC Quality & Resolution>, and press
[enTeR] button.
2. Select <event>.
Event recording setup window appears.
3. Use direction buttons ($%_ +) to move to a desired
item, and select it.
• Resolution : Sets the resolution of the recorded screen.
• Record Rate : Image Per Second, means the frames
recorded per a second.
• Record Quality : Sets the recording quality.
M
REC Quality & Resolution
Event
Standard
Remaining count : 4CIF(L) : 2
CH
2CIF(M) : 4
Resolution 
CIF(S) : 8
Record Rate 
Record Quality 
1
4CIF(L)

7fps

Level4

2
4CIF(L)

7fps

Level4

3
4CIF(L)

7fps

Level4

4
4CIF(L)

7fps

Level4

OK
Cancel
` The estimated total remaining count means the total number of remaining recordings for both standard and event
recordings.
` You cannot increase the remaining count if the current remaining count has reached zero or there is no available
remaining count from any other page. If this is the case, reduce the remaining count for the current page, or do so
for the same channel on any other page.
4. When the Event recording setup is done, press <OK>.
English _53
main menu
Record Option
You can set the recording to stop or overwrite when the HDD is full.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <Record> window to
move to <Record Option>, and press [enTeR] button.
Record Option
2. Use direction buttons ($%_ +) to move to a desired
Auto Delete
item, and set the value.
• Disk End Mode : If selected <Overwrite>, recording will
continue despite the HDD full while overwriting the oldest.
If selected <Stop>, the recording will stop when the HDD is
full.
• Disk End Beep : If selected <Stop>, the button is activated.
If you check it, the beep will sound on the disk full and the
recording stops.
• Auto Delete : If you check it, Record Period setup is activated.
If you specify the auto deletion period, the recording data before the period will be deleted automatically.
` This option will be enabled only if Disk End Mode is set to <Overwrite>.
 Disk End Mode
Overwrite
Disk End Beep

Auto Delete
180
day
The recording information will be deleted.
Do you want to proceed?
OK
OK
3. When the recording option setup is done, press <OK>.
54_ main menu
Cancel
Cancel
SeTTinG THe eVenT
You can set recording options for motion, and video loss event.
You can set target detection region and motion, as well as the alarm signal output.
When the motion detection region is set, it detects motion within the area.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <event> window to move to <motion Detection>, and press [enTeR]
button.
A window of motion detection area setup appears.
2. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Mode : Sets whether to activate motion detection.
• Sensitivity : Sets the sensitivity level of the motion detection.
• Alarm : Sets the alarm output method.
` For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 48)
• Alarm Duration : Sets the duration of alarm signal and alarm
sound.
Motion Detection
CH
Mode 
Sensitivity 
Alarm 
Alarm Duration 
1
OFF

Level10(High) 
None
10 sec

2
OFF

Level10(High) 
None
10 sec

3
OFF

Level10(High) 
None
10 sec

4
OFF

Level10(High) 
None
10 sec

Motion Region
OK
Cancel
3. When the motion detection setup is done, press <OK>.
Setting the motion Detection area
Select <motion Region>.
When “motion Region” window appears, select a
channel for detection and set the area of motion
detection.
• To set the area in “motion Region” window
In the “motion Region” window, select desired region
from <
>.
Motion Region
CH1
• To set the area using <individual> selection
Individual
OK
Apply to All CH
Cancel
In the “motion Region” window, you can select cells
individually by using <individual>.
When selected <individual>, “motion Region” window disappears and you can select cells one by one.
When the motion area setup is done, Right-click to select <menu> in the context menu or the [menu]
button on the remote control to display the “motion Region” window again.
- Select : Selected cell is set to be a part of motion detection area.
Select
- Unselect : Selected cell is removed from the motion detection area.
- Inverse : Unselected cells are set to be the motion detection area.
- Menu : After selecting individual motion areas, move to the “motion Region” window.
` If selected <Apply to All CH>, selected motion area is applied to all channels.
Unselect
Inverse
Menu
When the motion detection setup is done, press <OK>.
English _55
! main menu
motion Detection
main menu
Video Loss Detection
You can set the alarm to be generated on a camera disconnection, which causes a video loss.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <event> window to
move to <Video Loss Detection>, and press [enTeR]
button.
A window of video loss detection area setup appears.
2. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Video Loss State : Sets whether to activate video loss
detection.
• Alarm : Sets the alarm output method.
` For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 48)
Video Loss Detection
CH
Video Loss State 
Alarm 
Alarm Duration 
1
OFF

None
2
OFF

None
10 sec


None
10 sec

10 sec

3
HelpOFF
4
OFF
None

If a video loss event occurs during the event
recording, the POST recording settings of
the applicable channel will be reset.
10 sec

OK
Help
OK
Cancel
• Alarm Duration : Sets the duration of alarm signal and alarm sound.
• Help : Displays a help message that will appear if a video loss event occurs.
3. When the video loss detection setup is done, press <OK>.
alarm Schedule
You can set the conditions and operating hours for scheduled alarms.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <event> window to
move to <alarm Schedule>, and press [enTeR] button.
2. A window of <alarm Schedule> settings appears.
3. Alarm : Sets the alarm output method.
` For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 48)
Alarm Schedule
BEEP
All
0 1 2 3 4
Tue
Wed
Thu
Fri
Sat
Hol
OFF
ON
• <On> : Marked in orange, and always generates alarm on
scheduled time.
• <OFF> : Marked in white, no alarm is generated even if an
event occurs.
• Event Sync : Marked in Blue, generates alarm only when an event occurs.
M
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
Mon
Event Sync
OK
Cancel
` When the alarm is generated on the scheduled time, you can stop the alarm by canceling the schedule.
4. When the Alarm Schedule setup is done, press <OK>.
56_ main menu
BaCKuP
You can check the backup device and set the backup schedule by channel or by time.
The product only supports external HDD of USB memory and USB type. (Page 111)
You can backup the desired data to a connected device.
Using the mouse may help make setup easier.
1. Press the [menu] button on the remote control.
Logout
2. Use the left/right button (_ +) to select <Backup>.
Backup menu is selected.
Return
Backup
Backup
3. Press the [enTeR] button.
A backup window appears.
You can directly access it from the “Live screen menu”.
(Page 24)
4. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Backup Range : Sets the <Start> and <end> time for the
backup.
• Channel : Sets the channel to backup.
You can select multiple channels.
• Device : Select a backup device from the recognized devices.
• Type : Sets the backup data format.
Backup
 Start
2012-01-01 00:01:06
 End
2012-01-01 08:25:45
 Overlap List0
ALL
1
2
3
4
 Device
USB-Storage
 Type
DVR
 Folder
\20120101\
 Filename
0001
Backup
Used
Free
Check capacity
OK
Change
Cancel
- DVR : Saved data can be played back only by the DVR.
- SEC : Saves data in the Samsung’s proprietary format with built-in viewer, which supports immediate
playback on a PC.
• Filename : You can set the back file name.
` Refer to “Using Virtual Keyboard”. (Page 35)
• Check capacity : Shows the size of the selected backup data, used and available capacity of the selected
backup device.
` Checking will stop if the backup size is over 200%.
• Overlap : Shows a list of overlapping data on a same time according to the number of data.
It appears when one channel has multiple data on a certain time point due to changing of time or time zone
settings, etc.
` Refer to time and time zone of “Setting the Date/Time/Language”. (Page 32)
English _57
! main menu
Setting the Backup
main menu
5. When the backup setup is done, press <OK>.
` If no available device is recognized for backup, <OK> button is not activated.
J
` The application may slow down during the backup.
` You can switch to the menu screen during the backup in operation, but playback of data is not available.
` If backup has failed, select “Device > Storage Device” and check the free space of the HDD and check also if the
HDD is properly connected.
M
` Pressing the <Exit> during the backup will return to the previous menu, while the backup progresses.
neTWORK COnFiGuRaTiOn
It provides networked monitoring of Live screen from a remote place, and supports mail forwarding function with
events. You can configure the network environment which enables such functions.
Connection mode
You can set the network connection route and protocol.
Setting the Connection
Sets the protocol and environment of the network.
Using the mouse may help make setup easier.
1. Press the [menu] button on the remote control.
2. Use the left/right button (_ +) to select <network>.
Network menu is selected.
Logout
3. Use the up/down buttons ($%) to move to <Connection
mode>, and press [enTeR] button.
Network
Connection Mode
DDNS
Live Transfer
Mailing Service
4. Select <Connection>.
A window of connection mode setup appears.
5. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Connection Mode : Sets the network connection mode.
• Bandwidth : Sets the maximum data flow to be transferred.
(Upload speed)
Options will vary depending on the selected connection
mode.
- For <Static iP>, <Dynamic iP> : Select one from
50 kbps ~ 2Mbps, and Unlimited.
- For <aDSL>, select one from 50 kbps ~ 600 kbps.
58_ main menu
Return
Connection Mode
Connection
Protocol
 Connection Mode
Static IP
 Bandwidth
2Mbps
 IP
192.168. 1.200
 Gateway
192.168. 1.
 Subnet Mask
255.255.255. 0
 DNS
Manual
1
168.126. 63. 1
OK
Cancel
• IP, Gateway, Subnet Mask, and DNS
- For <Static iP> : You can directly input IP address,
Gateway, Subnet Mask and DNS.
- For <aDSL> : IP address, Gateway, and Subnet Mask are
set automatically.
• User ID, Password : In case you selected ADSL, provide the
“user iD” and its “Password”.
M
Protocol
 Connection Mode
ADSL
 Bandwidth
600kbps
 IP
192.168. 1.200
 Gateway
192.168. 1.
 Subnet Mask
255.255.255. 0
 DNS
Manual
 User ID
ID
 Password
************
1
! main menu
- For <Dynamic iP> : IP address, Gateway, and Subnet
Mask are set automatically.
Connection Mode
Connection
168.126. 63. 1
OK
Cancel
` DNS server for <Dynamic IP> and <ADSL> can be set by user only if you selected <Manual>.
6. When the connection setup is done, press <OK>.
Setting the Protocol
1. Use the up/down buttons ($%) in <network> window to
move to <Connection mode>, and press [enTeR]
button.
2. Select <Protocol>.
3. Use direction buttons ($%_ +) to move to a desired
item, and set the value.
• Protocol Type : Select the protocol type between TCP and
UDP.
` If selected UDP, selections of Port (TCP), Port (UDP), and Unicast/
Multicast are activated.
Connection Mode
Connection
 Protocol Type
 Port(TCP)
Protocol
TCP
4520
 Port(UDP)
~
Unicast
 Multicast IP
224.126.63.1
 TTL
 Webviewer Port
4524
8000 ~ 8160
 Unicast/Multicast
5
80
* Multi Browser Support :
TCP Port 4505~4530, Webviewer Port 80
OK
Cancel
` If setting the connection mode to ADSL, you cannot select UDP for the protocol type.
• Port(TCP) : Initially, <4520~4524> is set. It increases / decreases by 5.
- TCP: It has better stability and lower speed when compared to UDP, and recommended for internet
environments.
• Port(UDP) : Initially, <8000~8160> is set. It increases / decreases by 160.
- UDP : It has less stability and faster speed when compared to TCP, and recommended for local area
network (LAN) environments.
• Unicast/Multicast : Select one between Unicast and Multicast.
If selected Multicast, Multicast IP and TTL are activated.
- Unicast : Transfers data (UDP, TCP) individually to each connecting client.
- Multicast : Multiple client can receive the data (only in UDP) without putting additional traffic load to the
network.
• Multicast IP : User can directly input.
• TTL : Select from 0 ~ 255. Initial value for the TTL is set to <5>.
• Webviewer Port : Enter the port number for the Web Viewer. Initially, it is set to <80>.
• Multi Browser Support : You can use a Silverlight-compliant web browser to connect to the Web Viewer.
Multi browsers are enabled only if the TCP port is set to between 4505 and 4530 with the Web Viewer port
of 80. This is a security measure in order to enable Silverlight.
M
` As UDP protocol may cause a packet loss on the network, it is recommended to use TCP protocols.
` If you select UDP protocols and set port forwarding in the IP router, ending up with an unstable network connection,
configure the DMZ settings in the IP router as necessary.
4. When the protocol setup is done, press <OK>.
English _59
main menu
notification
J
` In a multi-browser environment, the web port should be set to 80 (private port).
Select one between 4505 and 4530 for RTSP
• network Overview
Router (External IP: 109.112.92.133,
Local IP: 192.168.1.1
Cable/ADSL
Modem
Internet
DIGITAL VIDEO RECORDER
POWER
REC
Local PC
System
DVR 1
WEB
DIGITAL VIDEO RECORDER
POWER
DVR 1
DDNS Server
(www.samsungipolis.com)
REC
DVR 2
RTSP
DVR 2
WEB
RTSP
IP
192.168.1.200
192.168.1.200
192.168.1.202
192.168.1.202
Private Port
80
4520~4524
81
4525~4529
Protocol
TCP
Public Port
80
Connection Mode
Connection
TCP
TCP
4520~4524
81
4525~4529
Connection Mode
Connection
Protocol
 Connection Mode
Protocol
 Connection Mode
Static IP
 Bandwidth
2Mbps
 Bandwidth
2Mbps
 IP
192.168.1.200
 IP
192.168.1.202
 Gateway
192.168.1.1
 Subnet Mask
255.255.255.0
 DNS
Manual
 Gateway
192.168.1.1
 Subnet Mask
255.255.255.0
 DNS
Manual
168.126.63.1
OK
Connection Mode
Connection
TCP
 Port(TCP)
4520
 Port(UDP)
~
Unicast
 Multicast IP
224.126.63.1
 TTL
4524
Cancel
5
 Protocol Type
TCP
 Port(TCP)
4525
~
 Unicast/Multicast
Unicast
 Multicast IP
224.126.63.1
 Webviewer Port
4529
8000 ~ 8160
 TTL
80
OK
Protocol
 Port(UDP)
* Multi Browser Support :
TCP Port 4505~4530, Webviewer Port 80
60_ main menu
OK
Connection
8000 ~ 8160
 Unicast/Multicast
 Webviewer Port
168.126.63.1
Connection Mode
Protocol
 Protocol Type
Static IP
Cancel
5
81
* Multi Browser Support :
TCP Port 4505~4530, Webviewer Port 80
Cancel
TCP
OK
Cancel
• 1st Set Port Forwarding Setting
Port Forwarding is 4520~4524
(4520, 4521, 4522, 4523, 4524)
Port Forwarding is 80
SDR-3100
TCP
TCP
4520
80
192. 168. 1. 200
4520
! main menu
SDR-3100
192. 168. 1. 200
80
• 2nd Set Port Forwarding Setting
Port Forwarding is 4525~4529
(4525, 4526, 4527, 4528, 4529)
Port Forwarding is 81
SDR-3100
SDR-3100
TCP
TCP
4525
81
192. 168. 1. 202
4525
192. 168. 1. 202
81
English _61
main menu
Connecting and Setting the network
Networking may differ from the connection method, check your environment before setting the connection mode.
When no router is used
• Static iP mode
- Internet connection : Static IP ADSL, leased line, and LAN environments allows connection between the
DVR and remote user.
- DVR Network Settings : Set the <Connection mode> in
<Connection> menu of the connected DVR to <Static iP>.
` Consult your network manager for IP, Gateway and Subnet Mask.
• Dynamic iP (DHCP) mode
- Internet connection : Connect the DVR directly to a cable
modem, DHCP ADSL modem or FTTH network.
Connection Mode
Connection
 Connection Mode
Protocol
Static IP
 Bandwidth
2Mbps
 IP
192.168. 1.200
 Gateway
192.168. 1.
 Subnet Mask
255.255.255. 0
 DNS
Manual
- DVR Network Settings : Set the <Connection mode> in
<Connection> menu of the connected DVR to <Dynamic iP>.
1
168.126. 63. 1
OK
Cancel
• aDSL (PPPoe: iD and password certification)
- Internet connection : An ADSL modem is directly connected to the DVR, where the ADSL connection
requires user ID and password.
- DVR Network Settings : Set the <Connection mode> in
<Connection> menu of the connected DVR to <aDSL>.
` <User ID> and <Password> should be the same to the ADSL
user information.
If you don’t know the ID and password, consult your ADSL service
provider.
Connection Mode
Connection
Protocol
 Connection Mode
ADSL
 Bandwidth
600kbps
 IP
192.168. 1.200
 Gateway
192.168. 1.
 Subnet Mask
255.255.255. 0
 DNS
Manual
 User ID
ID
 Password
************
168.126. 63. 1
OK
62_ main menu
1
Cancel
When a router is used
JJ `` To avoid IP address conflict with the DVR's static IP, check followings :
-- Internet connection : You can connect the DVR to a router which is connected to an ADSL/Cable modem
or a router in a Local Area Network (LAN) environment.
• Setting the DVR Network
1. Set the <Connection Mode> in <Connection> menu of the connected DVR to <Static IP>.
2. Check whether the set IP address is in the static IP range provided by the Broadband Router.
IP, Gateway, and Subnet Mask : Consult your network manager.
`` Check whether the set IP address is in the static IP range provided by the Broadband Router.
DHCP server is configured with starting address (192.168.0.100) and end address (192.168.0.200), you should
JJ `` Ifseta the
IP address out of the configured DHCP range (192.168.0.2 ~ 192.168.0.99 and 192.168.0.201 ~
192.168.0.254).
3. Check the Gateway address and subnet mask are equal to those set in the Broadband Router.
• Setting the DHCP IP Address of the Broadband Router
1. To access the Broadband Router’s configurations, open a web browser on the local PC that is connected
to the Broadband Router and enter the router’s address (ex : http://192.168.1.1).
2. At this stage, make the local PC's windows network configurations to the below example :
Ex) IP : 192.168.1.2
Subnet Mask : 255.255.255.0
Gateway : 192.168.1.1
-- Once connected to the Broadband Router, it prompts with password. While entering nothing to the User
Name field, enter “admin” into the password field and press <OK> to access the router configurations.
-- Access the router’s DHCP configuration menu and set its DHCP server activation, and provide the start and
end address.
Set the start address (192.168.0.100) and end address (192.168.0.200).
MM `` Above steps may differ from the router devices depending on the manufacturer.
English _63
! main menu
• Setting the DVR with a static IP
main menu
• Setting Router’s Port Forwarding
1. Set the protocol to <TCP>.
Connection Mode
2. External Port Range : Enter the TCP Port set in the
<Port(TCP)> in <Protocol> menu of the connected DVR.
If more than one DVRs are connected to the router, the
TCP port can be different.
Connection
 Protocol Type
 Port(TCP)
TCP
4520
 Port(UDP)
3. Internal PC IP Address : Enter the IP address set to the
<iP> in <Connection> menu of the connected DVR.
~
Unicast
 Multicast IP
224.126.63.1
 Webviewer Port
4524
8000 ~ 8160
 Unicast/Multicast
 TTL
5
80
* Multi Browser Support :
TCP Port 4505~4530, Webviewer Port 80
4. Internal Port Range : Set the same to the “external Port
Range”.
M
Protocol
OK
Cancel
` Above steps may differ from the router devices depending on the manufacturer.
Port forwarding is required when you want to access the DVR connected to the router from outside of the router’s
network.
❖ in case of Port Forwarding Setting
1. Download the program.
Install it in your PC. Run <Simple Port Forwarding>.
` To download visit http://www.simpleportforwarding.com/
download
2. Click <(2)Do it now> in Check List.
Type your router information.
If you can’t find the exact router in the list, update the
router list or choose a similar router in the same
manufacturer.
3. Click the icon for checking your router IP address.
64_ main menu
c
b
Click <OK> for updating your router IP address.
b
! main menu
Type your router Username & Password.
If you haven’t changed them, skip this procedure, for it
provides default value.
c
4. Click <(4)Do it now> in Check List for choosing the
ports.
b
Click <OK> for updating your router IP address.
IP Address : 192.168.1.200
Type : TCP
Start Port : 80
End Port : 80
IP Address : 192.168.1.200
Type : TCP
Start Port : 4520~4524
End Port : 4520~4524
c
English _65
main menu
5. After checking if the list is right, click <(5)Do it now> for
updating your router.
DDnS
You can set the DDNS site for a remote user’s network connection.
Using the mouse may help make setup easier.
1. Use the up/down buttons ($%) in <network> window to
move to <DDnS>, and press [enTeR] button.
2. Use virtual keyboard to enter user inputs.
` Refer to “Using Virtual Keyboard”. (Page 35)
• If selected <OFF> or <iPOLiS>, input fields are deactivated.
• If you select <iPOLiS>, the “DDNS host address” item will
be displayed.
- Type your set ID in <Product iD> field.
More specific information in “iPOLiS DDNS Setting”.
DDNS
 DDNS Site
iPOLiS
 Server Name
www.samsungip...
 Product ID
HOMEDVR
 Quick Connect
 DDNS Host Address
Not Use
Use
http://www.samsungipolis.com/HOMEDVR
OK
Cancel
- Select <use> in <Quick Connect> menu. After finishing
“iPOLiS DDnS Setting”, you can connect your DVR set with the address <http://www.samsungipolis.com/
HOmeDVR>.
` The router used should support uPNP Port Forwarding function.
` Note that uPNP Port Forwarding does not support UDP protocol.
` If the program fails to read uPNP Port Forwarding List, try again after restarting the computer and router.
3. When the DDNS setup is done, press <OK>.
66_ main menu
DDnS Setting
• Setting DDnS in the DVR
Set <Protocol Type> in the <Protocol> menu of the connected DVR to the following :
Ex) Protocol Type : TCP
Port (TCP) : 4520~4524
DDNS Site : iPOLiS
❖ iPOLiS DDnS Setting
1. Visit http://www.samsungipolis.com or
http://www.samsungipolis.co.kr and click <LOGin>.
2. If you have ID & PASSWORD, insert them.
Otherwise, click <SiGn uP> for a new account.
3. After log in, register your set with your information.
b
b
c
English _67
! main menu
DDNS is a short form of Dynamic Domain Naming System.
DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters
(ex : www.google.com) to an IP address consisting of numbers (64.233.189.104).
DDNS (Dynamic DNS) is a service that registers a domain name and the floating IP address with the DDNS
server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP
system.
main menu
4. After registration, you can see the list as below.
5. Select <iPOLiS> and fill Server Name out with your
registration information.
DDNS
 DDNS Site
iPOLiS
 Server Name
www.samsungip...
 Product ID
SDR3100HOME
 Quick Connect
 DDNS Host Address
Not Use
Use
http://www.samsungipolis.com/SDR3100HOME
OK
Cancel
OK
Cancel
6. You can see <STaTuS> changed to <On> in 10 minutes,
if all the network settings are right.
Live Transfer
Sets the quality of the image that is transferred from the DVR to the network.
Using the mouse may help make setup easier.
1. In the <network> setting window, press the up/down
($%) button to move to <Live Transfer> and press the
[enTeR] button.
The Live Transfer window appears.
Live Transfer
 Resolution
CIF(S)
 Quality
Low
2. Use the direction buttons ($%_ +) to move to a desired
item and set the value.
3. When the live transfer is done, press <OK>.
` The resolution for real-time (live) transfer will be set to CIF(S).
(Page 53)
68_ main menu
mailing Service
You can send an e-mail to a DVR-registered user at a specific time interval, or if an event occurs.
` If an event occurs with a channel where the camera’s video is set to <OFF> or the remaining recording count is set
to <OFF>, only the text notification will be sent to the applicable email address.
! main menu
M
` The e-mail receivers are not able to adjust the attached image quality.
SmTP Setting
Sets the SMTP mail server.
Using the mouse may help make setup easier.
1. In the <network> setting window, press the up/down
($%) button to move to <mailing Service> and press the
[enTeR] button.
2. Select <SmTP>.
You will see the SMTP setting window.
Mailing Service
SMTP
 ServerType
Group
Event
Recipient
SMTP mail Server
 Server
 Port
25
Use Authentication
User
3. Use direction buttons ($%_ +) to move to a desired item
and set the value.
• ServerType : Displays the connected server type.
• Server : Enter a server to connect to.
• Port : Sets the communication port.
• Use Authentication : Check this if the SMTP server uses user authentication.
The account input box will be activated.
• User : Enter a user to use authentication when connecting to the SMTP server.
• Password : Enter the password of the SMTP server user.
• Secure Transfer : Select one from <never> and <TLS(if available)>.
• Sender : Use the virtual keyboard to enter the sender’s e-mail address.
` Refer to “Using Virtual Keyboard”. (Page 35)
Password
 Secure Transfer
Never
 Sender
ex. user@example.net
TEST
OK
Cancel
• TEST : Conducts the test on the server settings.
4. When the SMTP setting is done, press <OK>.
English _69
main menu
event Setting
You can set the interval and type of the event that will be sent to the user.
Using the mouse may help make setup easier.
1. In the <network> setting window, press the up/down
($%) button to move to <mailing Service> and press the
[enTeR] button.
2. Select <event>.
3. Use direction buttons ($%_ +) to move to a desired item
and set the value.
• Event Interval : Set the event interval.
` If a series of events occurs, the e-mail will be sent at the specified
interval, not on each event.
Mailing Service
SMTP
Event
 Event Interval
Group
Recipient
10 min
 Use Event Transfer
Motion
Change P/W
HDD Info
Power On/Off
Manual Record
OK
Video Loss
Cancel
• Use Event Transfer : Select an event type to send if an event occurs.
If the selected event occurs, the e-mail will be sent to the group that has the recipient authority.
4. When the event setting is done, press <OK>.
Group Setting
You can set the group to whom the e-mail is sent, and specify the permission for each group.
You can add recipients for each group in the <Recipient> menu item.
The recipient is set separately from the DVR user group.
Using the mouse may help make setup easier.
1. In the <network> setting window, press the up/down
($%) button to move to <mailing Service> and press the
[enTeR] button.
2. Select <Group>.
3. Use direction buttons ($%_ +) to move to a desired item
and set the value.
• Add : Select <add> and use the virtual keyboard to add a
group.
` Refer to “Using Virtual Keyboard”. (Page 35)
Mailing Service
SMTP
70_ main menu
Add
Recipient
Delete
Rename
 Recipient Permission
Motion
Change P/W
HDD Info
Power On/Off
Manual Record
• Delete : Deletes the selected group.
• Rename : You can reset the recipient permission of an existing group.
• Recipient Permission : Set the permission of the recipient group.
4. When the group setting is done, press <OK>.
Group
Event
 Group
OK
Video Loss
Cancel
Recipient Setting
You can add/remove a recipient(s) to/from the specified group and edit the group if necessary.
Using the mouse may help make setup easier.
2. Select <Recipient>.
Mailing Service
SMTP
 Group
Event
Recipient
Group
All Group
Group
Add
Name
e-Mail Address
Del
3. Use direction buttons ($%_ +) to move to a desired item
and set the value.
Previous/ Next Page
OK
• Add : You can select a recipient name, e-mail address or
group.
You should have created a group in the <Group> menu
item before you can add a user to the group.
` For inputting the recipient name and email address, refer to
“Using Virtual Keyboard”. (Page 35)
4. When the recipient setting is done, press <OK>.
Cancel
Mailing Service
SMTP
 Group
Event
Recipient
Group
ABC
Group
Add
Add recipient
Name
e-Mail Address
Del
 Name
 Email
 Select Group
ABC
OK
Cancel
Previous/Next Page
OK
Cancel
English _71
! main menu
1. In the <network> setting window, press the up/down
($%) button to move to <mailing Service> and press the
[enTeR] button.
search & play
COnTROLLinG a PTZ DeViCe
The DVR enables you to adjust the settings of a PTZ camera as well as an ordinary one to your preference.
PTZ Device
The PTZ device can be activated only if a channel in connection with the PTZ camera is selected.
Getting started with PTZ
The PTZ camera is available, only if a channel is selected, in the following way :
` Using the remote control buttons
Press the [PTZ] button on the remote control.
` Using the launcher menu
Click PTZ <
PTZ
> to display the live launcher.
` Using the right-click menu in Live mode
Right-click any area on the screen to display the context menu,
and select <PTZ Control>.
` Using icons on the live screen
Click the PTZ <
M
> icon on the live screen.
` The PTZ function is available only if the PTZ camera is
connected so that the PTZ icon is displayed on the screen.
72_ search & play
Scene Mode
2012-01-01 01:10:25

PTZ Control
Zoom In
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
2012-01-01 01:10:25
using the PTZ camera
You can use one camera to perform all functions of PAN, TILT and ZOOM for monitoring multiple places and
set the preset to your preference in a desired mode.
M
2012-01-01 01:10:25
` Be sure to configure PTZ working environments before
operation, since the PTZ Working(Active) mark can be
appeared to be activated even when PTZ is not operative.
PTZ Control CAM01
Auto Pan
Select
Scan
Select
Camera Setup
Select Preset
2. Use the PTZ wheel in the launcher menu to adjust the
monitoring area, or use the direction buttons ($%_ +) on
the remote control to move the camera to a desired place.
• PTZ Wheel : Clicking a nearer point to the center will move in that direction slowly; clicking a farther point
from the center will move fast.
` Keep clicking left to rotate the lens counter clockwise; keep clicking right to rotate the lens clockwise.
Pattern
Select
Preset
Select
Save
Rename
Delete
Delete
All All
Delete
Delete
Exit
• Zoom (
) : You can use the Zoom function of the PTZ camera.
• IRIS (
) : Adjusts the intensity of radiation incoming to the iris.
• Focus (
) : Enables you to adjust the focus manually.
• Auto Pan : The camera automatically runs between the two points that you selected.
• Scan : The camera moves to the preset points in the specified sequence.
If multiple presets are specified, the PTZ camera will automatically move to all of the preset points one at a
time.
• Pattern : Makes the PTZ camera remember and follow the past route.
` The functions of Auto Pan, Scan and Pattern are supported in the protocols of Samsung, Panasonic and Pelco, and are
different in terms of the name and setting, depending on the protocols of Samsung, Panasonic and Pelco.
(Panasonic : Auto Pan, Sequence, Sort / Pelco : Auto Pan, Frame Scan (Scan), Pattern)
M
` Before entering the PTZ device control mode, set the values of the PTZ device in the <Setting the PTZ> menu.
(Page 46)
English _73
! SeaRCH & PLaY
1. Launch the <PTZ Control> menu.
As the PTZ <
> icon on the bottom right corner turns
yellow, you access the “PTZ Control” mode to display the
“PTZ Control” menu.
search & play
Preset Setting
A preset is a set of specific target points of a PTZ camera, and up to 127 presets per a camera can be stored.
1. In PTZ Control mode, use the direction buttons to adjust the camera in a desired direction.
2. Select the <Save> key.
The virtual keyboard for inputting the preset will appear.
` Refer to “Using Virtual Keyboard”. (Page 35)
• Save : You can save the preset settings.
• Rename : You can change the settings of the existing presets.
• Delete : Deletes the selected preset.
• Delete All : Deletes all existing presets.
M
` If you replace the camera of the channel that stores the preset list with a new one, you should reset the preset
accordingly.
3. Press <OK>.
The preset will be saved as a name that you entered.
Camera Setting
A PTZ camera has its own menu system. Optimize the PTZ camera according to the DVR.
1. Connect the PTZ camera to the DVR and run the PTZ
camera again to display the camera’s protocol setting
window.
2. Check the protocol ID of the camera.
` In “Device > Setting the PTZ”, enter the PTZ camera ID
the ID input box of the channel that is connected to the PTZ
camera. (Page 46)
2012-01-01 01:10:25
SAMSUNG PROTOCOL
ADDR
TYPE
BAUD
LENS
TILT
PAN
3. Select <Camera Setup> in the PTZ Control menu.
The camera-specific menu appears.
` You can configure the settings of only those cameras that
support the protocols of Samsung, Pelco D/P, AD and Panasonic.
` If you are setting Auto Pan or Pattern in the camera menu, press
and hold the appropriate button for a certain time so that the
button operation can be different from that in normal PTZ setting.
2012-01-01 01:10:25
** MAIN MENU **
Camera Setup

Exit
74_ search & play
0
RS-485,HALF
9600
OK!
OK!
OK!
CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
CLOCK SET...
SYSTEM INFO...
in
search & play
SeaRCH
You can perform the search for recorded data by the time or by the search criteria such as an event.
You can access the <Search> menu directly in Live mode.
1. In Live mode, right-click any area of the screen.
The Live menu appears.
! SeaRCH & PLaY
2012-01-01 01:10:25
Scene Mode 
Audio Off
2. Select <Search>.
Or, press the [SeaRCH] button on the remote control.
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
3. The Search menu appears.
2012-01-01 01:10:25
4. The search can be restricted by the Auto Delete function.
Refer to “Setting the Recording > Record Option”.
(Page 54)
M
Return
Time Search
Event Search
` Overlapped data : It only appears if there exists overlapped
Backup Search
Motion Search
data on a certain time, produced due to the change of DVR’s
time setup. The latest data comes first, from <List0>.
It does not appear in <Backup Search>.
Time Search
You can search for recorded data of a desired time.
As the time to display may be different depending on the time zone and the DST standard time, the time of
data recorded in the same time can be displayed differently depending on time zone and DST settings.
Using the mouse may help make setup easier.
1. Select <Time Search> in the <Search> menu.
2. Select a date to search.
` Refer to “Using the Calendar”. (Page 34)
3. The record data on the specific date will be listed.
The display bar is different according to the data type.
So check the data type for the color in the left pane.
Time Search
Go to First
2012-01-01
Go to Last
Overlapped Data List1
Zoom In
Zoom Out
00:01
All
Data
CAM 01
CAM 02
2012/01/01 00:01:17
Standard
Schedule
Motion
Etc
CAM 03
CAM 04
4. Use direction buttons ($%_ +) to set the search criteria
and press the [enTeR] button.
• Go to First : Moves to the earliest date.
• Go to Last : Moves to the most recent date.
• Time : Enter a time to perform the search or use the up/down button <>> to select one.
V.Loss
Play
Return
English _75
search & play
• Zoom In : The map enlarges in detail.
It will switch in the sequence of 24 hours - 16 hours - 8 hours
- 4 hours.
• Zoom Out : The map will switch in the reverse order of the
detailed mode above.
It will switch in the sequence of 4 hours - 8 hours - 16 hours
- 24 hours.
M
` Double-click a desired time to zoom it in/out.
Time Search
Go to First
2012-01-01
Go to Last
Overlapped Data List1
Zoom In
Zoom Out
00:01
All
Data
CAM 01
CAM 02
2012/01/01 00:01:17
Standard
Schedule
Motion
Etc
CAM 03
CAM 04
V.Loss
Play
Return
• Preview : Click <Channel> and select (click, drag) a time in
<Duration> to display a still image for the portion.
- If the selected channel does not contain any recorded data, it will be marked black.
5. Select a data item and click <Play>.
The screen switches to the data playback mode.
event Search
You can search for events by the channel and play them.
Using the mouse may help make setup easier.
1. Select <event Search> in the <Search> menu.
2. Use direction buttons ($%_ +) to set the search criteria
and press the [enTeR] button.
` All record events on a specific date will be found. (Normal/
Schedule recording included)
• Date/Time Preview : If you select a data item in the list, the
still image of the selected data will be displayed in the left
preview pane.
• Event : Displays the type of the event that occurred.
3. Select a data item and click <Play>.
The screen switches to the event data playback mode.
76_ search & play
Event Search
CAM 01
2012-01-01
Overlapped Data
List1
Go to First
Go to Last
No.
Date/Time Preview
3
02:47:54 ~ 02:48:59
Motion
2
00:39:06 ~ 00:40:30
Motion
Event
1
00:01:22 ~ 00:02:28
Motion
2012/01/01 00:01:22
Previous/Next Page
Play
Return
Backup Search
Using the mouse may help make setup easier.
1. Select <Backup Search> in the <Search> menu.
2. Use direction buttons ($%_ +) to set the search criteria
and press the [enTeR] button.
• Record Period : Displays the record period.
• Channel info : Displays the recorded channel.
• Play Start Time : Select a time that you start playing.
3. Select a data item and click <Play>.
The screen switches to the backup data playback mode.
Backup Search
USB:USB2FlashStorage
No.
Folder
File Name
1
20120101
16190000
Previous/Next Page
 File Name 16190000  Channel info 1
 Record Period
2012-01-01 01:01:01 - 2012-01-01 01:01:10
 Play Start Time
2012-01-01
01:01:01
Play
Return
motion Search
If a motion is detected in each channel, you can set a desired area to perform the search.
You can use the mouse to select the related items.
1. Select <motion Search> in the <Search> menu.
2. Use direction buttons ($%_ +) to set the search criteria
and press the [enTeR] button.
` If you set the motion area to <Manual Area>, the <Setup>
button will be activated.
• Motion Region : Select an area to perform the search.
- All Area : Searches for all areas of the selected channel.
Motion Search
Channel
CAM 01
Date/Time
2012-01-01 03:41:18
Overlapped Data
Motion Region
List1
Go to First
No.
Start Time
7
01:01:30
6
01:01:25
5
01:01:20
4
01:01:15
3
01:01:10
2
01:01:05
1
01:01:01
2012/01/01 01:01:30
- Current Area : Searches for the motion area for each
channel specified in “motion Detection >
Setting the motion Detection area”. (Page 55)
- Manual Area : You can set the motion area manually.
• Setup : The Setup button will be activated only if you have
set the motion area to Manual. Press this button to display
the area setting window.
• Date/Time : The Date/Time will be automatically set by the
hour, and the end time will be automatically set to one hour
later than the start time if it is set.
• Preview : Select a data item in the list to display the still
image of the item.
3. Select a data item and click <Play>.
The screen switches to the motion data playback mode.
Setup
All Area
2012-01-01 05:11:44
Search
Go to Last
Previous/Next Page
Play
Return
Motion Region
CH1
Individual
OK
Apply to All CH
Cancel
English _77
! SeaRCH & PLaY
Searches for backup data in the connected backup device.
Only data in the format of DVR is included in the search.
Refer to <Type> in “Backup > Setting the Backup”. (Page 57)
search & play
PLaYBaCK
Play
You can play data stored in the HDD and backup a desired portion of the data.
Using the mouse may help make setup easier.
1. In Live mode, click <Play> in the right-click menu or
> in the launcher menu, or press the Play button on
<
the remote control.
2012-01-01 01:10:25
Scene Mode 
Audio Off
Freeze
2. Use the up/down button ($%) to select a menu.
` For data search, refer to <Search>. (Page 75)
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
3. Select a data item and click <Play> in the Search menu.
The selected data is played and the play launcher appears
on the screen.
` If there is an existing data, <Play> will start immediately without
performing the search.
2012-01-01 01:10:25
• Playback Information : Displays the date and time of the
current data in the top corner.
ReC
• Backup : Click <
> to set the current time to the start
time of backup; you can specify a backup area using the
mouse (yellow triangle).
> again to set the current time to the end time of
Click <
the backup and the “Backup Range” window appears.
Backup Range
 Start
 End
2012-01-01 00:01:06
2012-01-01 01:10:25
 Device
USB Storage
 Type
 Folder
\20120101\
 Filename 0001
Check capacity
- Type : Supports formats of DVR and SEC.
Refer to a list of formats in “Setting the Backup”.
(Page 57)
- Device : Select a backup device.
- Check Capacity : Enables you to check the capacity of
the selected storage device.
4. If you want to return to the Live screen in Play mode, click <
[@] button on the remote control.
78_ search & play
DVR
Change
Backup
Used
Fre
OK
Cancel
> in the launcher menu or press the
using the Playback Button
! SeaRCH & PLaY
ReC
b c Part Names
m
Play Timeline
Indicates the current playback point, and can be used to move.
b
Skip Backward
Moves backward by unit time.
Backward Fast
Play
Backward Slow
Play
Functions
c
n
Used for quick backward playback.
Used for backward frame-by-frame search while in PAUSE.
Step Backward
Moves backward by one frame at a time.
Pause
Stops playing the current video temporarily.
Stop
Stops playback and moves to the live screen.
Step Forward
Moves forward by one frame at a time.
Forward Slow
Play
` In a split mode, the real time playback may not be supported, depending on the record
Forward Fast Play Used for quick forward playback.
Skip Forward
Moves forward by unit time.
Return
Return to the search setup screen.
m
Audio
` If using both web view and DVR set simultaneously, the audio signal will be output from the
n
REC
Records all channels in Live mode.
Partial Backup
Begins backup of the selected section of the video being played, with the specified starting/ending
point.
Mode Switch
Click a desired playback mode or press [MODE] to switch the screen mode in sequence.
Ensured to play forward up to 4 channels simultaneously at a low speed.
quality, resolution and number of channels. And some frame rates may be supported.
Sets Audio ON/OFF.
DVR set.
English _79
web viewer
Introducing Web Viewer
What is Web Viewer?
Web Viewer allows remote access to your DVRs. You have
access to live video, archived video etc.
Product Features
• Remote access from a standard browser
• Supports 1, 4 camera viewing formats (maximum of 4
cameras in the list).
• Gets JPEG, BMP format images to print and save to “Print
or Save JPEG, BMP format images”.
• Record video in AVI format-compatible with popular media
players. (needed the H.264 codec)
System Requirements
The following lists the minimum suggested hardware and operating system requirements needed to run the
Web Viewer.
OS
Web Browser
CPU
Windows XP Professional
Windows 2000
Windows Vista Home Basic / Premium
Windows 7
Safari 5.1.1 or later version
Internet Explorer 6.0.2900.2180 or higher
Intel Pentium 4, 2 GHz
Memory
512 MB
Monitor
High Color 16-bit 1024 x 768
HDD
50 MB(Installation space required)
* Additional HDD space required for recording.
Recorded file size will vary depending on recording quality settings.
for computers of higher performance than recommended, you may experience frame skipping with the Web
JJ `` Even
Viewer if the computer is overloaded showing more than 80% of CPU usage.
80_ web viewer
connectIng Web VIeWer (MAc)
❖ Safari on MAc.
1. Click [click now to Install] to display the installation
screen as shown.
2. Double-click the [Silverlight.pkg] icon to display the
Silverlight plug-in installation screen as shown.
3. Click [continue] to start installing Silverlight plug-in.
When done, you will see the screen as below.
4. Click [close] to exit from the Silverlight plug-in installation
screen.
English _81
! Web VIeWer
If you want to use DVR Web Viewer with Safari Browser on a Mac, please refer to this user guide and install
Multi Viewer with firmware upgrade if necessary.
• Brower versions available: Safari 5.1.1 or later version
• Silverlight: 4.0.60831.0 or later
web viewer
• If Microsoft Silverlight plug-in is already installed
1. Use a web browser to connect to the DVR.
2. If Silverlight plug-in is already installed, you will see the
screen as shown.
3. If this is the case, perform Step 3 [tcP port & Web
Viewer port settings] below.
4. If the screen above does not appear, check if the DVR set is connected properly with a valid IP address.
uSIng lIVe VIeWer (MAc)
The Live Viewer screen consists of following :
b
a
c
d
e
f
g
h
i
k
j
a This displays the IP address and the model name of the connected DVR.
b These menus consist of <lIVe>, <About>.
c These buttons are used for the screen split and full screen mode.
d Shows the IP address and model name of the connected DVR.
e Select to turn the sound on/off.
f Select <dVr time> or <Pc time> for the OSD time information display setting of the Live Viewer.
g These buttons are used for sequence and changing the screen channel.
h These buttons are used for capture, print, and save the image.
When you can’t play the file recorded in web, install the H.264 CODEC
ex) MAC: perian_1.2.3.dmg (http://perian.org)
i Shows the channel of the connected DVR.
j These buttons are used for PTZ related functions.
k This displays the screen for connected camera with DVR.
82_ web viewer
connectIng Web VIeWer (WIndoWS)
1. Open your web browser and type the IP address or URL
of DVR into the URL address box.
http://www.samsungipolis.com/HOMEDVR
2. Set the Admin ID and password same to those of the DVR
Admin.
For general users, enter the DVR user ID and password.
J
` The default password can be exposed to a hacking thread so
it is recommended to change the password after installing the
product.
` Set password for your wireless network if you use the product with a wireless router. Being not protected with
password or using the default wireless router password may expose your video data to potential threat.
` Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
M
It allows up to 4 simultaneous access including the Admin and general users.
It does not allow multiple login of the Admin user.
Initial password of the Admin user is set to “4321”.
Password of the Admin and general users can be changed in <Permission Management> menu of the DVR.
Normal users should have set <Viewer> under <Permission Management> to “Use” before connecting to the
Web Viewer. (Page 35)
` All settings are applied by the DVR’s settings.
`
`
`
`
`
3. Click <Install ActiveX control…>.
Downloading Active-X control may take several minutes
according to the security settings on your PC.
4. Click <Install>.
English _83
! Web VIeWer
M
The basic URL of the DVR is as following in case of MAC
address :
` http://www.samsungipolis.com/User ID
` You can also use registered URL which setups up in the Setup menu of your DVR.
web viewer
5. You may have “Windows Security Alert” that attempts to
block this with the Windows Firewall. In that case, click
<unblock> to start Web Viewer.
6. Installation is complete.
Now you can see the main screen of Live Viewer.
uSIng lIVe VIeWer (WIndoWS)
The Live Viewer screen consists of following :
b
a
c
d
e
f
g
h
i
k
j
a This displays the IP address and the model name of the connected DVR.
b These menus consist of <lIVe>, <SeArch>, <SetuP>, <About>.
c These buttons are used for the screen split and full screen mode.
d Shows the IP address and model name of the connected DVR.
e Select to turn the sound on/off.
Select the format of OSD information that will be displayed on Live Viewer.
f Select <dVr time> or <Pc time> for the OSD time information display setting of the Live Viewer.
g These buttons are used for sequence and changing the screen channel.
h These buttons are used for capture, print, and save the image.
i Shows the channel of the connected DVR.
j These buttons are used for PTZ related functions.
k This displays the screen for connected camera with DVR.
M
` The initial split-screen mode is set according to the number of channels connected to DVR. You can change the
split-screen mode by clicking buttons for split-screen modes.
84_ web viewer
oSd Information display
a The channel number, video size, and IP address of the
connected DVR are displayed.
b
! Web VIeWer
b This icon will appear if the audio signal is currently being
output.
a
c The current date and time will be displayed according to the
selected time information display setting <dVr time> or
<Pc time>.
d Motion icon appears when motion is detected. It disappears
when pressed the [AlArM] button of the DVR..
e It displays whether the PTZ controls are active.
M
` If you have set PTZ cameras for the DVR, “PTZ” is displayed on
c
de
the screen. Select a PTZ camera channel and use the [PTZ] button for camera control.
Split-Screen
SINGLE MODE
QUAD MODE
You can change the split mode by clicking each number icon.
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“SIngle Mode”.
• Click <
> button.
The screen displays the selected camera connected to the DVR in “QuAd
Mode”.
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“Full Screen Mode”.
Double clicking on the screen or pressing any button of the keyboard
returns to the previous mode.
English _85
web viewer
connected dVr
This displays the IP address and the status of the connecting DVR.
M
` Connection failure message
No Response : Appears when the DVR does not respond.
Access Denied : Appears when the maximum number of users is exceeded.
` The number of simultaneous connections are limited to 4.
Setting the display of the oSd time Information
Select <dVr time> or <Pc time> for the OSD time information display
setting.
• dVr time : Based on the time of the connected DVR
• Pc time : Based on the time of the PC currently running the Web Viewer.
• Audio : Sound On/Off
changing the live Screen Mode
• SeQuence : When this button is clicked, screens are switched at a
preset interval.
In SINGLE MODE, the channel numbers are sequentially switched from
1 to 4.
` Preset interval (10 seconds)
• PreVIouS : When this button is clicked, the previous screen appears.
• neXt : When this button is clicked, the next screen appears.
In SINGLE MODE, the channel numbers are sequentially switched from
1 to 4.
Saving the live Screen on the Pc
• cAPture : Saves the current screen into a BMP or JPEG
file.
M
` The default saving path is “C:\Program Files\Samsung\DVR
Web Viewer\SnapShot\Live”. To change the saving path, click
)> button and then select the path you
<SAVE PATH (
want. For Windows Vista or 7, the saving path is “C:\users\
(user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\
SnapShot\” by default.
` The file is automatically named as following : “IP address_Port number_YYYYMMDD_HHMMSS_camera number_index”
Ex) 192.168.1.200_554_20120101_134132_01_00
86_ web viewer
• PrInt : Prints out the selected screen out of the currently
displayed live screens. It also prints the IP address, time,
camera number and the current event status together.
! Web VIeWer
• record : Saves the current image on the screen and
saves it as a avi video file.
M
` To record it, it is required at least 1GB of available space.
` The default saving path is “C:\Program Files\Samsung\DVR
Web Viewer\VideoClip\Live”. To change the saving path, click
<SAVE PATH (
)> button and then select the path you
want. For Windows Vista or 7, the saving path is “C:\users\
(user ID)\AppData\Local-Low\Samsung\DVR Web Viewer\VideoClip\”.
` The file is automatically named as following : “IP address_Port number_YYYYMMDD_HHMMSS_camera number_index”
Ex) 192.168.1.200_554_20120101_135105_01_00
` For AVI Save, you need the H.264 codec for playing saved files.
` HDD Minimum Free Size : During the recording, if there is no more capacity available in the HDD than set free space
will prompt with a popup message : “Cannot record due to insufficient disc space in the HDD”.
changing the live Screen channel
• Blue numbers : The channel connected to the current live screen
• Gray numbers : The channel not connected to the current live screen
` If you select 4-split mode, the channel button for each of cameras 1 ~ 4 will turn
blue.
English _87
web viewer
using PtZ camera
Click the direction buttons to control the camera.
• <
>
• <
>
• <
>
You can zoom in or out an image by using the ZOOM button.
You can adjust the entering light amount by using the IRIS button.
You can adjust the focus by using the FOCUS button.
• Menu : Appears the camera menu screen.
88_ web viewer
• Preset : Moves the lens direction to a preset direction.
1. If you click a preset, the camera moves to the selected
preset's position.
2. You can delete the selected preset or all presets.
! Web Viewer
3. You can save a new preset number and name.
MM `` You can save presets up to 127.
• Auto Pan : Moves the camera lens direction between
2 points set for the camera.
• Scan : Moves the camera lens direction between 2 preset
points of the camera.
• Pattern : You can set camera various movement patterns
such as zoom, move, etc. so that a camera automatically
moves according to the pattern.
the DVR controls a PTZ camera, Web Viewer cannot
MM `` While
control the camera.
`` Camera menu setup is only available for camera supporting the
``
``
``
``
``
function.
Each function of PTZ is same to that of the DVR.
Pan/Tilt of the Smart dome camera is manipulated
automatically to center the camera to the mouse clicked point.
If you drag the mouse using the left button on a certain point,
Pan/Tilt of the Smart dome camera is manipulated
automatically to center the camera to the middle point between
the dragging start and end position.
Upward dragging will zoom out, while downward dragging will zoom in.
Tilt of Power PTZ operates properly within 45°.
Power and Pan Tilt functions are only available for camera supporting the functions.
Ex : Samsung SCC-C6475
English _89
web viewer
uSIng SeArch VIeWer
The Search Viewer screen consists of following :
b
a
c
d
e
f
g
k
h
i
j
a This displays the IP address and the model name of the connected DVR.
b There are 4 tabs available: <lIVe>, <SeArch>, <SetuP>, <About>.
c Switch to a split mode.
d Shows the IP address and model name of the connected DVR.
e Select the format of OSD information that will be displayed on Live Viewer.
f These buttons are used for capture, print, and save the image.
g This displays a calendar at which you can search the recorded video.
h The duplicate check list will appear If there are found duplicates in the same timeline.
The duplicated items will be listed in latest-first order.
i This displays a timeline at which you can search the recorded video by the time.
j These buttons are used for controlling playback.
k This displays the screen for playback of recorded video.
M
` <SEQUENCE>, <PREVIOUS>, <NEXT> buttons are not available in SEARCH menu.
` During the DVR backup, you may have a trouble accessing CMS & Web Search.
` Web Viewer on only Internet Explorer can support “Search” function.
90_ web viewer
Split-Screen
You can change the split mode by clicking each number icon.
! Web VIeWer
SINGLE MODE
QUAD MODE
> button.
• Click <
The screen displays the selected camera connected to the DVR in
“SIngle Mode”.
• Click <
> button.
The screen displays the selected camera connected to the DVR in
“QuAd Mode”.
connected dVr
This displays the IP address and the status of the connecting DVR.
M
` Connection failure message
No Response : Appears when the DVR does not respond.
Access Denied : Appears when the maximum number of users is exceeded.
` The number of simultaneous connection is limited to 2.
English _91
web viewer
Saving the live Screen on the Pc
• cAPture : Saves the current screen into a BMP or JPEG
file.
M
` The default saving path is “C:\Program Files\Samsung\DVR
Web Viewer\SnapShot\Search”. To change the saving path,
)> button and then select the path
click <SAVE PATH (
you want. For Windows Vista or 7, the saving path is “C:\
users\(user ID)\AppData\LocalLow\Samsung\DVR Web
Viewer\SnapShot\”.
` The file is automatically named as following : “IP address_Port number_YYYYMMDD_HHMMSS_camera number_index”
Ex) 192.168.1.200_554_20120101_134132_01_00
• PrInt : Print out the current screen. It also prints IP
address, time, camera number and current event state.
• record : While in playback, press this button saves the
video data of the selected channel as an AVI file. (It is saved
in the designated folder on your PC.)
To stop recording, click this button again.
M
` To record it, it is required at least 1GB of available space.
` The default saving path is “C:\Program Files\Samsung\DVR
Web Viewer\VideoClip\Search”. To change the saving path,
)> button and then select the path you want. For Windows Vista or 7, the saving path is
click <SAVE PATH (
“C:\users\(user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\VideoClip\”.
` The file is automatically named as following : “IP address_Port number_YYYYMMDD_HHMMSS_camera number_index”
Ex) 192.168.1.200_554_20120101_135105_01_00
` For AVI save, you need the H.264 codec for playing saved files.
92_ web viewer
Searching the recorded Video in the calendar
! Web VIeWer
If the video data has been recorded on a date, the date is
distinguished in green. If you click the date, the recorded video
information is displayed in the time line. When you click
<today>, it will be synchronized with the system time (date) of
the current PC.
check duplicates
If there are found duplicates in the same timeline after you changed the DVR
time, those duplicates will be listed in the <0> order with the latest one on top.
Searching the recorded Video in the timeline
It displays the recorded video data status on the DVR after a date is
selected. The normal mode displays the time ranging from 0 to 24 Hours
while the extension mode displays the time every 2 hours.
[Normal Mode]
• If you click < > button, it changes to the extension mode.
• Each time line represents 1 hour.
[Extension Mode]
• If you click < > button, it changes to the normal mode.
• Each time line represents 5 minutes.
M
` The channels are ranging from CH01 to CH04.
English _93
web viewer
controlling Playback
a
b
e
f
c
g
h
d
i
a Fast backward : Reverse-plays faster(2x~64x).
b reverse Play : Performs Reverse Play.
c Play : Performs playback.
d Fast Forward : Plays faster(2x~64x).
e go to First : Moves the beginning time of recorded video in the time line.
f Step backward : Performs one step reverseplay by one frame.
g Pause : Stops the playback temporarily.
h Step Forward : Performs one step forward by one frame.
i go to last : Moves the last time of recorded video in the time line.
M
` Only the admin account can play the audio signal during the playback.
If using both web view and DVR set simultaneously, the audio signal will be
output from the DVR set.
VIeWer SetuP
You can configure the DVR settings remotely on the network.
To configure the DVR settings, click <Setup>.
System
You can configure the various settings of the DVR system.
date/time/language
For more information, refer to <date/time/language> in the <System Setup> menu. (Page 32)
1. Select <date/time/language> in the System menu.
2. Configure the DVR settings according to your system
environment.
• date/time
Set the date and time.
94_ web viewer
• time Synchronization Setup
Set the time synchronization.
! Web VIeWer
• display
Date Format : Set the date type.
Time : Select a time format to display on the screen.
• dSt (daylight Saving time)
DST is displayed an hour ahead of the standard time of the
time zone.
• language
Select a preferred language for the DVR.
holiday
You can set specific dates to Holidays according to your
preferences.
For more information, refer to <Setting holiday> in the
<System Setup> menu. (Page 34)
Permission Management
For more information, refer to <Permission Management> in the <System Setup> menu. (Page 39)
• Admin
You can change the admin ID or the password.
English _95
web viewer
• group
Users are classified into groups and the permission can be
set according to the group.
` First of all, add a group.
• user
You can add, change or remove a user or users.
• Setup
You can set the user permission.
System Management
For more information, refer to <System Management> in the <System Setup> menu. (Page 39)
• System Information
You can see information of the current system.
Check the software version, broadcast format and
MAC address.
96_ web viewer
device
camera
• camera
You can configure the settings of the camera that is connected
to the DVR.
• Privacy region
You can specify a certain area of the camera video to be
protected for your privacy.
• PtZ
You can configure the settings of the PTZ camera that is
connected to the DVR.
Set the ID and protocol.
English _97
! Web VIeWer
You can check a list of devices that are connected to the DVR and configure the necessary settings.
Click <device> in the menu screen.
For more information, refer to “Setting the device”. (Page 44)
web viewer
Storage device
You can check and change the settings of the storage device.
• device
You will see a list of storage devices that are connected to the
DVR.
You can check the type, used/total, usage and status of the
device.
• hdd Alarm
You can set the alarm output channel and the alarm duration
for an error.
remote device
Specify the use of remote control and the remote control ID so
that you can synchronize with the DVR.
Monitor
• Monitor
You can configure the monitoring screen settings and set the
output system.
98_ web viewer
• Mode
You can switch between live mode and play mode.
! Web VIeWer
record
For more information, refer to <Setting the recording>. (Page 51)
recording Schedule
If you set a recording schedule for a specific date and time,
the recording will start at that specific time.
- Apply to All CH : Click <Apply to All ch> to display the
confirmation window.
event record duration
You can set the start and end times of recording that will be
activated if an event occurs.
English _99
web viewer
rec Quality & resolution
• Standard/event
You can set the resolution, frame rate and recording quality for
each channel.
record option
You can set the Disk End Mode.
event
For more information, refer to <Setting the event>. (Page 55)
Motion detection
You can set the motion detection mode and the sensitivity
as well as the alarm output type and the duration.
100_ web viewer
• Motion region
Set the target motion detection area
! Web VIeWer
Video loss detection
You can set the alarm output time if a video loss occurs.
Alarm Schedule
You can schedule the alarm output according to the day of the
week and the time.
The default setting is Event Sync, which activates the alarm
only if an event occurs.
English _101
web viewer
network
For more information, refer to <network configuration>. (Page 58)
connection
A remote user can access the DVR via the network to check the current mode and the IP address.
• connection
You can set the network connection route.
• Protocol
You can configure the protocol related settings.
ddnS
You can check the DDNS settings.
` If you select <iPOLiS>, the “DDNS Host Address” item will be
displayed.
102_ web viewer
live transfer
A remote user can set the images of the DVR.
• live transfer
! Web VIeWer
A remote user can set the image resolution of the transferred
data.
Mailing Service
You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users.
• SMtP
You can set the server that sends mails and specify if you use
the authentication process.
• event
You can set the event interval and specify which events the
server sends mails for.
English _103
web viewer
• group
You can add a group to receive the mail if an event occurs
and set the permission to receive the event mail for each
group.
• recipient
You can add a user or users who will receive the mail.
About
Click <About>.
Displays the model name of connected DVR and the version of
Web Viewer
SDR-3100
20XX. XX. XX
104_ web viewer
Mobile Viewer
What is Mobile Viewer?
Using a Smartphone
1. Download the Samsung iPOLiS mobile app.
On an Android phone, visit Play Store.
On an iPhone, visit App Store.
2. Search for Samsung iPOLiS.
3. Launch the iPolis mobile app add the DVR.
On an Android phone, tap on the menu icon and tap <Add
Device>.
On an IPhone, at the Add Device pop-up tap <OK>.
English _105
! Web Viewer
iPOLIS mobile is smartphone application that enables you to connect to DVR (Digital Video Recorder)
remotely and control the video playback and PTZ operations (if configured) in real time.
backup viewer
4. Register the DVR to the iPOLiS mobile.
JJ Name : Create a name for the DVR you are adding
Model : Select the DVR model
Host : If you are using Samsung iPolis DDNS, enter the host DDNS Host
Address you wrote down earlier.
It should be www.samsungipolis.com/Product ID
HTTP Port : If you are using iPolis DDNS, you do not need to enter this
information
RTSP Port : Enter the Port (TCP) you wrote down earlier.
Camera : Select the cameras you want to view.
5. Enter the User ID and Password for the DVR.
JJ Default user login info is ID : admin and Password : 4321
Key Features
• Remote access via Smartphone
• 1-split and 4-split modes supported in Live Viewer (However, search is not available).
• Switch channels using the touch-sensitive LCD panel
• Up to 4 channels supported
• Audio (wifi : O, 3G : X)
• PTZ camera operations supported (complies with the protocol of the connected DVR)
Compatible Smartphone
This application is optimized for
• iPhone OS v4.3.5, v6.0.1
• Android v2.2/2.3 or later(Galaxy S/S2 recommended)
to your DVR Setting for HTTP and RTSP Port Setting.
MM `` Refer
Mobile Viewer uses the last value of the RTSP port numbers you registered in your DVR.
Ex) HTTP: 80, RTSP 4520-4524
For more information refer to “Setting the Protocol”. (Page 59)
106_ backup viewer
backup viewer
Sec bAcKuP VIeWer
You can play a file that is backed up in the format of SEC.
Backup in the format of SEC will involve in generating two files: one for the backup data and one for the viewer.
! bAcKuP VIeWer
If you run the backup file viewer, the backup data file will be automatically played.
recommended System requirements
PCs with a lower specification than the recommended below may not fully support forward/backward and
high-speed playback.
• OS : Windows XP professional, Windows Vista, Windows 7 (It is not supported by MAC OS.)
• CPU : Intel Core2-Duo 2.4GHz or higher
• RAM : DDR PC-3200 1G or more
• VGA : Geforce 6200 or higher
English _107
backup viewer
Name
a
b
c
f
/
Audio
A toggle button. Each time you press this button, the audio output will toggle
between activated and deactivated.
You can adjust the volume level from 0 to 100.
Saves the current screen as an image file. Supported file formats include
BMP and JPEG.
Screen Printout
File Tamper
Detection
Prints out the current screen. You should have installed the appropriate printer
driver before you can print out the screen.
/
Deinterlace
d
e
Description
Zoom In/Out
Display of storage time range
A toggle button. Each time you press this button, it will toggle between
activated and deactivated. The closed lock icon indicates activation of the file
tamper detection, which will blink the screen three times and stop playing if
an unauthorized manipulation of a data file is detected.
`` A message of “The file is forged” will display in the menu bar.
You can enable the De-interlace function.
Collapses the time range that is displayed on the range bar of the storage
time. You can collapse the range bar until the overall range is shortened to 24
hours.
Enlarges the time range that is displayed on the range bar of the storage
time. You can enlarge the range bar until the overall range is extended to 1
minute.
Displays the time range of a stored video file.
You can move the gridline of the range bar to select a time point to play.
A toggle button; each time you press this button, the "Slow Playback" icon
changes its color to display it’s activated/deactivated. If it is activated, you can
use the play speed control to adjust the play speed up to x1/16 forward and
backward respectively, whereas if deactivated, you can adjust up to x16
forward and backward.
g
Speed
A toggle button; each time you press this button, the "Lock Speed" icon
changes its color to display it’s activated/deactivated.
If activated, the adjusted speed will be kept even if you release the mouse on
the speed bar. If deactivated, the adjusted speed will be applied only while
you use the mouse to hold the adjusted speed, and if you release the mouse,
the speed will restore to x1.
You can adjust the play speed up to x16 forward and backward respectively,
which varies according to the frame rate per second of the source.
Fast playback maximum is limited to x2 for footages recorded at 20 ~ 30 fps
(frames per second), x4 for 11 ~ 19 fps, x8 for 6 ~ 10 fps, and x16 for footages
recorded at slower than 6 fps.
108_ backup viewer
Name
Description
Displays the next frame. This is available only if the playback is stopped.
Play
A toggle button. Press it once to start playing the video and switch the button
mode to 'Pause', and press it again to switch the button mode to Play and
stop playing temporarily.
Displays the previous frame. This is available only if the playback is stopped.
English _109
! Backup Viewer
h
appendix
Product Specification (Camera)
❖❖ SDC-5340BC
Item
Electrical
Input Voltage
Power Consumption
Video
SDC-5340BCN
3W
1/3'' CMOS
Scanning System
Interlace
Synchronization
Frequency
Horizontal Resolution
Min. Illumination
S/N Ratio (Y Signal)
Lens
Focus Length
Max.Aperture Ratio
Angular Field of View
Operational
720 x 480
Internal
H: 15,734 Hz, V: 59.94 Hz
600TVL
OLux (IR-LED)
46dB
3.6mm
2
D: 72˚
H: 60˚
V: 48˚
Shutter Mode
Auto (Rolling Shutter)
White Balance
Auto (3200°K~6500°K)
Gain Control
Digital Noise Reduction
Day & Night
IR Distance
Environmental
Operating Temperature/
Humidity
Auto
Auto
MECHA IR CUT FILTER
25m
-10°C ~ +50°C (+14°F ~ +122°F) / 20% ~ 85% RH
IP Grade
IP66
Dimension (W X H X D)
W70.5 X H61 X D196.7 mm (2.77 X 2.4 X 7.74 inch)
Mechanical
Weight
110_ appendix
SDC-5340BCP
DC 12V
Imaging Device
Total Pixels
Details
241g
H: 15,625 Hz, V: 50 Hz
Product Specification(DVR)
`` Design and specifications are subject to change without prior notice.
❖❖ SDR-3100
Video
Live
Performance
Operating System
4 composite video 0.5-1 Vpp, 75 ohm
Frame rate
30fps NTSC, 25fps PAL
Resolution
Multi Screen display
Embedded
Compression
Record Rate
Recording
Mode
Overwrite modes
Pre-Alarm
Post-Alarm
Search & Playback
Search mode
Smartphone
Storage
704x480 NTSC, 704x576 PAL
704x480 NTSC, 704x576 PAL
1, 4, PIP
Linux
H.264
NTSC : Up to 30fps @ 704x480 / PAL : Up to 25fps @ 704x576
NTSC : Up to 60fps @ 704x240 / PAL : Up to 50fps @ 704x288
NTSC : Up to 120fps @ 352x240 / PAL : Up to 100fps @ 352x288
Manual, Schedule, Event, Time Laps
Continuous
Off / 5sec
Up to 6 hour. (5, 10, 20, 30 sec, 1, 3, 5, 10, 20 min,1, 2, 3, 4, 5, 6 hour)
Date/time, Event, Back up, Motion
Playback function
Fast Forward/Backward, Slow Forward/Backward, Step Forward/Backward
Bandwidth
Up to (4)Mbps, Unlimited(4M)/2/1.5/1 Mbps/800/600/500/400/300/200/
100/50 kbps
Transmission speed
Network
SDR-3100
Inputs
Resolution
! APPENDIX
Details
Item
Bandwidth control
Stream
Maximum No. of remote
users
NTSC:120fps, PAL:100fps
Automatic
H.264(CIF)
Search(2) / Live Unicast(4) / Live Multicast(20)
Protocol support
TCP/IP, DHCP, PPPoE, SMTP, NTP, HTTP, DDNS, RTP, RTSP
SmartPhone
Support
Monitoring
Internal HDD
External HDD
DVD Writer (Back-up)
USB (Back-up)
File Forma (Back-up)
Smartviewer, Webviewer, Mobile Viewer
500GB SATA HDD
–
–
2 USB Ports
BU(DVR Player), SEC(Include Player)
English _111
appendix
Details
Item
Security
Interface
Monitors
Password Protection
1 Admin, 10 Group, 10 User per 1 Group
VGA
Analog RGB 1024x768 resolution(BNC or VGA selected in booting.)
Main Composite
BNC, 1 Vp-p, 75 ohm
Data Authentication
HDMI
Spot Composite
Loop Outputs
Audio
Alarm
Inputs/Output
Compression
Sampling rate
Inputs/Outputs
Remote notification
Ethernet
Serial interface
Connections
USB
e-SATA
Application Supoort
General
Electrical
Environmental
Mechanical (Set)
Mechanical (Package)
Lauguage
112_ appendix
SDR-3100
Watermark
–
–
–
1 Line in(CH1) / 1 line out(RCA)
G.711
8KHz
–
Notification via e-mail
1 RJ45 10/100 Base-T
–
USB 2.0, 2 ports (Front/Rear)
–
Mouse (1EA), Remote Controller
Protocol support
RS485 (SAMSUNG-T, VICON, PANASONIC, AD, PHILIPS, Pelco D,Pelco P,
SAMSUNG-E)
Input Voltage/Current
DC12V, 1.8A, AC 100~240V, 50~60Hz
Operating Temperature/
Humidity
0°C ~ +40°C (+32°F ~ +104°F) / 20% ~ 85%RH
Power consumption
AHN-2212KFI(1EA), 21.6W
Dimension (W X H X D)
W255 X H50 X D213 mm (10.04 X 1.97 X 8.39 inch)
Dimension (W X H X D)
W365 X H405 X D170 mm (14.37 X 15.94 X 6.69 inch)
Weight (With hard disks)
Weight (With hard disks)
Rack mount kit
1.56kg
5.5Kg
–
English, Spanish, French, German, Italian, Polish, Portuguese, Russian,
Turkish, Japanese, Czech, Swedish, Danish, Korean, Chinese, Netherland,
Thai, Romanian, Serbian, Croatian, Hungarian, Greek
Default Setting
This returns the factory default settings.
Category
Details
Date/Time/Language
Date/Time/Language
System Settings
Permission
Management
System Management
Admin
Setting
System Information
Camera
Camera
Screen Setup
Device
Storage Device
Remote Device
HDD Alarm
Remote Device
Date
Factory Default
YYYY-MM-DD
Time Format
24 hours
Time Zone
GMT+09:00
Time Synchronize
OFF
DST
OFF
Language
English
ID
admin
New Password
4321
Restricted Access
Backup
Auto Logout
OFF
Broadcast Format
NTSC/PAL
Video
ON
Audio
OFF
CH Name
CAM 01 ~ CAM 04
SEQ-Dwell Time
5sec
Brightness
50
Contrast
50
Color
50
Check Alarm Output Port
OFF
Duration
OFF
Replace Alarm Output Port
OFF
Duration
OFF
Remote Control
ON(00)
English _113
! APPENDIX
The settings are made as follows;
• Use System/Load Factory Default in MENU
`` The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
appendix
Category
Details
Monitor
Device
Monitor
Mode
Recording Schedule
Event Record Duration
Event
Video Loss Detection
Alarm Schedule
114_ appendix
Video Output
VGA
Display
All
Display Position Setup
30
Live Mode
ALL
Play Mode
ALL
PRE Event
OFF
POST Event
1 min
Event
Motion Detection
OFF
Both(Cont&Evnt)
REC Quality/Resolution
Record Option
Event Display
CH1
Normal Recording
Recording
Factory Default
Disk End Mode
Resolution
CIF(S)
Frame Rate
NTSC: 7 fps,
PAL: 5 fps
Record Quality
Level 4
Resolution
4CIF(L)
Frame Rate
NTSC: 7 fps,
PAL: 5 fps
Record Quality
Level 4
Setup
Overwrite
Disk End Beep
OFF
Auto Delete
OFF
Mode
OFF
Sensitivity
Level10(high)
Alarm
None
Duration
10 sec
Motion Region
All Area
Video Loss State
OFF
Alarm
None
Duration
10 sec
BEEP
Event Sync
Category
Details
Connection Mode
Protocol
Network
DDNS
Live Transfer
Static IP
Bandwidth
2Mbps
IP
192.168.1.200
Gateway
192.168.1.1
Subnet Mask
255.255.255.0
DNS
168.126.63.1
Protocol Type
TCP
Port (TCP)
4520~4524
Webviewer Port
80
DDNS Site
OFF
Resolution
CIF(S)
Quality
Low
SMTP
Mailing Service
Event
Group
Server
OFF
Port
25
Use Authentication
OFF
Secure Transfer
Never
Event Interval
10 min
Use Event Transfer
OFF
Group
OFF
Recipient Permission
OFF
English _115
! APPENDIX
Connection
Connection Mode
Factory Default
appendix
Troubleshooting
Symptom
Countermeasures
The system does not turn on and the indicator on the
front panel does not work at all.
yy Check if the power supply system is properly connected.
yy Check the system for the input voltage from the power source.
yy If the problem persists even after you have taken the above actions,
check the power supplier and replace it with a new one if neccessary.
Some channels display just a black screen even if
they receive video sources.
yy Check if the camera connected to the system properly displays the
image. Sometimes, this problem may occur on a camera that is not
properly connected to the video source.
yy Check if the camera is properly supplied with power.
yy Sometimes, this problem may occur on a channel with weak video signal
from a video distributor that is connected to multiple systems. In this
case, input the video source of the camera directly into the DVR. This
may find the cause and solve the problem.
If I press the [REC] button on the front panel, the REC yy Check if there is a free space on the HDD for the recording.
indicator does not flash, nor the player start recording. yy Check if the record mode is set to ON in the record mode setting.
The screen displays the logo image repeatedly.
yy This may occur from a problem with the main board, or the related
software is corrupt.
Contact the nearest service center for more information.
The Channel button does not work on the Live screen. yy The Channel button does not work if the current screen is in the event
monitoring mode.
In the event monitoring screen, press the [ALARM] button to exit the
screen and select a channel.
The cursor will not move to the Start button when I
start the calendar search.
yy Check if the channel and the date that you want to play are marked with
the V symbol.
Both channel and date should be checked before you can start playing
with the Start button.
When the alarm sounds, I press the [ALARM] button
on the Remote Control to release the alarm but it
does not work. The alarm persists and I could not set
it off in any way.
yy Press the [MENU] button to release the alarm in the following way:
1)To release the event monitoring mode : Monitoring Mode – set the
duration of the event monitoring to Off.
2)To release the alarm sound : Event Record Mode - Alarm (Motion
Detection/Video Loss) – deactivate the alarm sound.
3)To release the event : Event Record Mode - Alarm (Motion Detection/
Video Loss) – set the mode to Off.
116_ appendix
Symptom
Countermeasures
yy This message is displayed if there occurs a problem with the time
setting of the internal clock or an error in the clock itself.
Contact the retailer or the service center for more information.
The time bar is not displayed in Search mode.
yy The timeline can switch between normal and extension mode.
In extension mode, the time bar may not be displayed in the current
timeline. Switch to normal mode or use the left or right button to
navigate through the time bar.
The “NO HDD” icon and an error message are
displayed.
yy Check the HDD for connection. If the problem persists in a normal
condition, contact the nearest service center to have the HDD checked
by the service personnel.
I have connected an external storage device (external
SATA HDD) to the DVR but the DVR seems not to
recognize it.
yy See the compatibility list of external storage devices to check if the
connected device is supported by the DVR.
For the compatibility list, contact the retailer where you purchased the
DVR.
If I press the ESC key in full screen mode of the
WebViewer, the system does not switch to a normal
split mode.
! APPENDIX
A message of “Need to reset date/time.” Is displayed
on the screen.
yy Press the ALT+TAB keys to select ‘ACTIVE MOVIE’ and press the ESC
key again. The system will switch to a normal split mode.
I found it difficult to configure the network settings if
using the default search, backup and router settings.
yy For more information, refer to the user manual.
yy If you want to check the basics of the product for a quick start, refer to
the quick start guide (backup, search).
I forgot the password.
yy Contact the DVR administrator for help.
Backup data is just not played by the PC or DVR.
yy When you are backing up data, you have choices about the player either:
PC or DVR. Make your selection before proceeding.
yy If you are using the PC to play the data, the format of the backup file
should be either SEC.
yy If you are using the DVR for this purpose, formatting backup files should
be done by the DVR.
My player does not switch to Live mode while in
playback.
yy Press the Stop [@] button on the remote control, or click the [
icon on the launcher to switch to Live mode.
]
English _117
appendix
Symptom
Countermeasures
Recording does not work.
yy If your player does not display a Live image at all, that indicates
recording does not work so first check if you see an image on the
screen.
yy Recording does not work if the recording settings are not properly
configured.
1)Manual Record: Press the [REC] button on the remote control to start
recording.
2)Scheduled Record: Specify a desired time in Menu – Record Recording Schedule. Recording will start at the specified time.
-- <Continuous> Record: Recording will proceed in any conditions at
the specified time.
-- <Event> Record: When an event occurs, recording will perform
only if the event is of alarm, motion detection and video loss.
If there is no event found, recording will not perform.
-- <Continuous / Event> Record: If there is no event found,
Continuous recording will perform. Whereas, if an event occurs,
Event recording will perform.
The image quality of the recording data is not good.
yy Increase the resolution and quality level in Menu – Record – Quality /
Resolution.
1)Resolution: Select a bigger size when specifying the recording size.
(4CIF> 2CIF>CIF)
The recording image in the CIF format shows a deteriorated quality as
it is enlarged from a small-sized image.
2)Record Quality: Specify a bigger level for the recording quality.
yy If you increase the resolution and the recording quality, the data size
increases accordingly. So the HDD will be filled faster. Overwriting will
overwrite the existing data so recording will proceed at a shorter interval.
118_ appendix
Open Source License Report on the Product
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete
Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source
distribution might be charged.
• GPL Software : linux kernel, Sysvinit, dosfstools, wget, msmtp, busybox, cdrtools, dvd+rw-tools, iconv, smartctl, uboot, minicom, openssl, bash,
lm_sensors
• LGPL Software : glibc, vmstat, inetutils
• OpenSSL License : OpenSSL
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom
to share and change it. By contrast, the GNU General Public License is
intended to guarantee your freedom to share and change free software
to make sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s software and
to any other program whose authors commit to using it. (Some other
Free Software Foundation software is covered by the GNU Lesser
General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price.
Our General Public Licenses are designed to make sure that you have
the freedom to distribute copies of free software (and charge for this
service if you wish), that you receive source code or can get it if you
want it, that you can change the software or use pieces of it in new free
programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone
to deny you these rights or to ask you to surrender the rights. These
restrictions translate to certain responsibilities for you if you distribute
copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis
or for a fee, you must give the recipients all the rights that you have. You
must make sure that they, too, receive or can get the source code. And
you must show them these terms so they know their rights.
We protect your rights with two steps:
(1) copyright the software, and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain
that everyone understands that there is no warranty for this free
software. If the software is modified by someone else and passed on,
we want its recipients to know that what they have is not the original, so
that any problems introduced by others will not reflect on the original
authors’ reputations.
Finally, any free program is threatened constantly by software patents.
We wish to avoid the danger that redistributors of a free program will
individually obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear that any patent must
be licensed for everyone’s free use or not licensed at all. The precise
terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin S
0. This License applies to any program or other work which contains a
notice placed by the copyright holder saying it may be distributed under
the terms of this General Public License. The “Program”, below, refers
to any such program or work, and a “work based on the Program”
means either the Program or any derivative work under copyright law:
that is to say, a work containing the Program or a portion of it, either
verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term
“modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of running
the Program is not restricted, and the output from the Program is
covered only if its contents constitute a work based on the Program
(independent of having been made by running the Program). Whether
that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s
source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices
that refer to this License and to the absence of any warranty; and give
any other recipients of the Program a copy of this License along with
the Program.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of
it, thus forming a work based on the Program, and copy and distribute
such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices
stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in
whole or in part contains or is derived from the Program or any
part thereof, to be licensed as a whole at no charge to all third
parties under the terms of this License.
c) If the modified program normally reads commands interactively
when run, you must cause it, when started running for such
interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that you provide a
warranty) and that users may redistribute the program under these
conditions, and telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but does not normally
print such an announcement, your work based on the Program is
not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves,
then this License, and its terms, do not apply to those sections when
you distribute them as separate works. But when you distribute the
same sections as part of a whole which is a work based on the
Program, the distribution of the whole must be on the terms of this
License, whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise the
right to control the distribution of derivative or collective works based on
the Program.
In addition, mere aggregation of another work not based on the
Program with the Program (or with a work based on the Program) on a
volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it,
under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable
source code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for
software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to
give any third party, for a charge no more than your cost of
physically performing source distribution, a complete machinereadable copy of the corresponding source code, to be distributed
under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to
distribute corresponding source code. (This alternative is allowed
only for noncommercial distribution and only if you received the
program in object code or executable form with such an offer, in
accord with Subsection b above.)
The source code for a work means the preferred form of the work for
making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control
compilation and installation of the executable. However, as a special
exception, the source code distributed need not include anything that is
normally distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating system on
which the executable runs, unless that component itself accompanies
the executable.
If distribution of executable or object code is made by offering access to
copy from a designated place, then offering equivalent access to copy
the source code from the same place counts as distribution of the
source code, even though third parties are not compelled to copy the
source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this License. Any attempt otherwise
to copy, modify, sublicense or distribute the Program is void, and will
automatically terminate your rights under this License. However, parties
who have received copies, or rights, from you under this License will not
have their licenses terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you have not
signed it. However, nothing else grants you permission to modify or
distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by
modifying or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License to do so, and all
its terms and conditions for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these
terms and conditions. You may not impose any further restrictions on
the recipients’ exercise of the rights granted herein. You are not
responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot distribute
so as to satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not
permit royalty-free redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only way you could
satisfy both it and this License would be to refrain entirely from
distribution of the Program.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply
and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents
or other property right claims or to contest validity of any such claims;
this section has the sole purpose of protecting the integrity of the free
software distribution system, which is implemented by public license
practices. Many people have made generous contributions to the wide
range of software distributed through that system in reliance on
consistent application of that system; it is up to the author/donor to
decide if he or she is willing to distribute software through any other
system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be
a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Program under this License may add
an explicit geographical distribution limitation excluding those countries,
so that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if
written in the body of this License.
9. The Free Software Foundation may publish revised and/or new
versions of the General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies a version number of this License which applies to it and “any
later version”, you have the option of following the terms and conditions
either of that version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number
of this License, you may choose any version ever published by the Free
Software Foundation.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to the author
to ask for permission. For software which is copyrighted by the Free
Software Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be guided by the
two goals of preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest
possible use to the public, the best way to achieve this is to make it free
software which everyone can redistribute and change under these
terms.
To do so, attach the following notices to the program. It is safest to
attach them to the start of each source file to most effectively convey
the exclusion of warranty; and each file should have at least the
“copyright” line and a pointer to where the full notice is found.
one line to give the program’s name and an idea of what it does.
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 2 of the License, or (at your
option) any later version.
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
the GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software Foundation,
Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
Also add information on how to contact you by electronic and paper
mail. If the program is interactive, make it output a short notice like this
when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details
type ‘show w’. This is free software, and you are welcome to
redistribute it under certain conditions; type ‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should show the
appropriate parts of the General Public License. Of course, the
commands you use may be called something other than ‘show w’ and
‘show c’; they could even be mouse-clicks or menu items--whatever
suits your program.
You should also get your employer (if you work as a programmer) or
your school, if any, to sign a “copyright disclaimer” for the program, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
‘Gnomovision’ (which makes passes at compilers) written by James
Hacker.
signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This
General Public License does not permit incorporating your program into
proprietary programs. If your program is a subroutine library, you may
consider it more useful to permit linking proprietary applications with the
library. If this is what you want to do, use the GNU Lesser General
Public License instead of this License.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute verbatim copies of this license
document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software
and other kinds of works.
The licenses for most software and other practical works are designed
to take away your freedom to share and change the works. By contrast,
the GNU General Public License is intended to guarantee your freedom
to share and change all versions of a program--to make sure it remains
free software for all its users. We, the Free Software Foundation, use the
GNU General Public License for most of our software; it applies also to
any other work released this way by its authors. You can apply it to your
programs, too.
When we speak of free software, we are referring to freedom, not price.
Our General Public Licenses are designed to make sure that you have
the freedom to distribute copies of free software (and charge for them if
you wish), that you receive source code or can get it if you want it, that
you can change the software or use pieces of it in new free programs,
and that you know you can do these things.
To protect your rights, we need to prevent others from denying you
these rights or asking you to surrender the rights. Therefore, you have
certain responsibilities if you distribute copies of the software, or if you
modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis
or for a fee, you must pass on to the recipients the same freedoms that
you received. You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they know their
rights.
Developers that use the GNU GPL protect your rights with two steps:
(1) assert copyright on the software, and (2) offer you this License giving
you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains
that there is no warranty for this free software. For both users’ and
authors’ sake, the GPL requires that modified versions be marked as
changed, so that their problems will not be attributed erroneously to
authors of previous versions.
Some devices are designed to deny users access to install or run
modified versions of the software inside them, although the
manufacturer can do so. This is fundamentally incompatible with the
aim of protecting users’ freedom to change the software. The
systematic pattern of such abuse occurs in the area of products for
individuals to use, which is precisely where it is most unacceptable.
Therefore, we have designed this version of the GPL to prohibit the
practice for those products. If such problems arise substantially in other
domains, we stand ready to extend this provision to those domains in
future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents.
States should not allow patents to restrict development and use of
software on general-purpose computers, but in those that do, we wish
to avoid the special danger that patents applied to a free program could
make it effectively proprietary. To prevent this, the GPL assures that
patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and
modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of
works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this
License. Each licensee is addressed as “you”. “Licensees” and
“recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work
in a fashion requiring copyright permission, other than the making of an
exact copy. The resulting work is called a “modified version” of the
earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work
based on the Program.
To “propagate” a work means to do anything with it that, without
permission, would make you directly or secondarily liable for
infringement under applicable copyright law, except executing it on a
computer or modifying a private copy. Propagation includes copying,
distribution (with or without modification), making available to the public,
and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other
parties to make or receive copies. Mere interaction with a user through
a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the
extent that it includes a convenient and prominently visible feature that
(1) displays an appropriate copyright notice, and (2) tells the user that
there is no warranty for the work (except to the extent that warranties
are provided), that licensees may convey the work under this License,
and how to view a copy of this License. If the interface presents a list of
user commands or options, such as a menu, a prominent item in the list
meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for
making modifications to it. “Object code” means any non-source form
of a work.
A “Standard Interface” means an interface that either is an official
standard defined by a recognized standards body, or, in the case of
interfaces specified for a particular programming language, one that is
widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other
than the work as a whole, that (a) is included in the normal form of
packaging a Major Component, but which is not part of that Major
Component, and (b) serves only to enable use of the work with that
Major Component, or to implement a Standard Interface for which an
implementation is available to the public in source code form. A “Major
Component”, in this context, means a major essential component
(kernel, window system, and so on) of the specific operating system (if
any) on which the executable work runs, or a compiler used to produce
the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all
the source code needed to generate, install, and (for an executable
work) run the object code and to modify the work, including scripts to
control those activities. However, it does not include the work’s System
Libraries, or general-purpose tools or generally available free programs
which are used unmodified in performing those activities but which are
not part of the work. For example, Corresponding Source includes
interface definition files associated with source files for the work, and the
source code for shared libraries and dynamically linked subprograms
that the work is specifically designed to require, such as by intimate
data communication or control flow between those subprograms and
other parts of the work.
The Corresponding Source need not include anything that users can
regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same
work.
2. Basic Permissions.
All rights granted under this License are granted for the term of
copyright on the Program, and are irrevocable provided the stated
conditions are met. This License explicitly affirms your unlimited
permission to run the unmodified Program. The output from running a
covered work is covered by this License only if the output, given its
content, constitutes a covered work. This License acknowledges your
rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not
convey, without conditions so long as your license otherwise remains in
force. You may convey covered works to others for the sole purpose of
having them make modifications exclusively for you, or provide you with
facilities for running those works, provided that you comply with the
terms of this License in conveying all material for which you do not
control copyright. Those thus making or running the covered works for
you must do so exclusively on your behalf, under your direction and
control, on terms that prohibit them from making any copies of your
copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the
conditions stated below. Sublicensing is not allowed; section 10 makes
it unnecessary.
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological
measure under any applicable law fulfilling obligations under article 11 of
the WIPO copyright treaty adopted on 20 December 1996, or similar
laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid
circumvention of technological measures to the extent such
circumvention is effected by exercising rights under this License with
respect to the covered work, and you disclaim any intention to limit
operation or modification of the work as a means of enforcing, against
the work’s users, your or third parties’ legal rights to forbid
circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you
receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice;
keep intact all notices stating that this License and any non-permissive
terms added in accord with section 7 apply to the code; keep intact all
notices of the absence of any warranty; and give all recipients a copy of
this License along with the Program.
You may charge any price or no price for each copy that you convey,
and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to
produce it from the Program, in the form of source code under the
terms of section 4, provided that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified
it, and giving a relevant date.
b) T
he work must carry prominent notices stating that it is released
under this License and any conditions added under section 7. This
requirement modifies the requirement in section 4 to “keep intact all
notices”.
c) You must license the entire work, as a whole, under this License
to anyone who comes into possession of a copy. This License will
therefore apply, along with any applicable section 7 additional
terms, to the whole of the work, and all its parts, regardless of
how they are packaged. This License gives no permission to
license the work in any other way, but it does not invalidate such
permission if you have separately received it.
d) If the work has interactive user interfaces, each must display
Appropriate Legal Notices; however, if the Program has interactive
interfaces that do not display Appropriate Legal Notices, your
work need not make them do so.
A compilation of a covered work with other separate and independent
works, which are not by their nature extensions of the covered work,
and which are not combined with it such as to form a larger program, in
or on a volume of a storage or distribution medium, is called an
“aggregate” if the compilation and its resulting copyright are not used to
limit the access or legal rights of the compilation’s users beyond what
the individual works permit. Inclusion of a covered work in an aggregate
does not cause this License to apply to the other parts of the
aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of
sections 4 and 5, provided that you also convey the machine-readable
Corresponding Source under the terms of this License, in one of these
ways:
a) Convey the object code in, or embodied in, a physical product
(including a physical distribution medium), accompanied by the
Corresponding Source fixed on a durable physical medium
customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product
(including a physical distribution medium), accompanied by a
written offer, valid for at least three years and valid for as long as
you offer spare parts or customer support for that product model,
to give anyone who possesses the object code either (1) a copy of
the Corresponding Source for all the software in the product that
is covered by this License, on a durable physical medium
customarily used for software interchange, for a price no more
than your reasonable cost of physically performing this conveying
of source, or (2) access to copy the Corresponding Source from a
network server at no charge.
c) Convey individual copies of the object code with a copy of the
written offer to provide the Corresponding Source. This alternative
is allowed only occasionally and noncommercially, and only if you
received the object code with such an offer, in accord with
subsection 6b.
d) Convey the object code by offering access from a designated
place (gratis or for a charge), and offer equivalent access to the
Corresponding Source in the same way through the same place at
no further charge. You need not require recipients to copy the
Corresponding Source along with the object code. If the place to
copy the object code is a network server, the Corresponding
Source may be on a different server (operated by you or a third
party) that supports equivalent copying facilities, provided you
maintain clear directions next to the object code saying where to
find the Corresponding Source. Regardless of what server hosts
the Corresponding Source, you remain obligated to ensure that it
is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided
you inform other peers where the object code and Corresponding
Source of the work are being offered to the general public at no
charge under subsection 6d.
A separable portion of the object code, whose source code is excluded
from the Corresponding Source as a System Library, need not be
included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any
tangible personal property which is normally used for personal, family, or
household purposes, or (2) anything designed or sold for incorporation
into a dwelling. In determining whether a product is a consumer
product, doubtful cases shall be resolved in favor of coverage. For a
particular product received by a particular user, “normally used” refers to
a typical or common use of that class of product, regardless of the
status of the particular user or of the way in which the particular user
actually uses, or expects or is expected to use, the product. A product
is a consumer product regardless of whether the product has
substantial commercial, industrial or non-consumer uses, unless such
uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods,
procedures, authorization keys, or other information required to install
and execute modified versions of a covered work in that User Product
from a modified version of its Corresponding Source. The information
must suffice to ensure that the continued functioning of the modified
object code is in no case prevented or interfered with solely because
modification has been made.
If you convey an object code work under this section in, or with, or
specifically for use in, a User Product, and the conveying occurs as part
of a transaction in which the right of possession and use of the User
Product is transferred to the recipient in perpetuity or for a fixed term
(regardless of how the transaction is characterized), the Corresponding
Source conveyed under this section must be accompanied by the
Installation Information. But this requirement does not apply if neither
you nor any third party retains the ability to install modified object code
on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a
requirement to continue to provide support service, warranty, or
updates for a work that has been modified or installed by the recipient,
or for the User Product in which it has been modified or installed.
Access to a network may be denied when the modification itself
materially and adversely affects the operation of the network or violates
the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided,
in accord with this section must be in a format that is publicly
documented (and with an implementation available to the public in
source code form), and must require no special password or key for
unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this
License by making exceptions from one or more of its conditions.
Additional permissions that are applicable to the entire Program shall be
treated as though they were included in this License, to the extent that
they are valid under applicable law. If additional permissions apply only
to part of the Program, that part may be used separately under those
permissions, but the entire Program remains governed by this License
without regard to the additional permissions.
When you convey a copy of a covered work, you may at your option
remove any additional permissions from that copy, or from any part of it.
(Additional permissions may be written to require their own removal in
certain cases when you modify the work.) You may place additional
permissions on material, added by you to a covered work, for which
you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add
to a covered work, you may (if authorized by the copyright holders of
that material) supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of
sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal notices or
author attributions in that material or in the Appropriate Legal
Notices displayed by works containing it; or
c) Prohibiting misrepresentation of the origin of that material, or
requiring that modified versions of such material be marked in
reasonable ways as different from the original version; or
d) Limiting the use for publicity purposes of names of licensors or
authors of the material; or
e) Declining to grant rights under trademark law for use of some
trade names, trademarks, or service marks; or
f) Requiring indemnification of licensors and authors of that material
by anyone who conveys the material (or modified versions of it)
with contractual assumptions of liability to the recipient, for any
liability that these contractual assumptions directly impose on
those licensors and authors.
All other non-permissive additional terms are considered “further
restrictions” within the meaning of section 10. If the Program as you
received it, or any part of it, contains a notice stating that it is governed
by this License along with a term that is a further restriction, you may
remove that term. If a license document contains a further restriction but
permits relicensing or conveying under this License, you may add to a
covered work material governed by the terms of that license document,
provided that the further restriction does not survive such relicensing or
conveying.
If you add terms to a covered work in accord with this section, you
must place, in the relevant source files, a statement of the additional
terms that apply to those files, or a notice indicating where to find the
applicable terms.
Additional terms, permissive or non-permissive, may be stated in the
form of a separately written license, or stated as exceptions; the above
requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as expressly
provided under this License. Any attempt otherwise to propagate or
modify it is void, and will automatically terminate your rights under this
License (including any patent licenses granted under the third paragraph
of section 11).
However, if you cease all violation of this License, then your license from
a particular copyright holder is reinstated (a) provisionally, unless and
until the copyright holder explicitly and finally terminates your license,
and (b) permanently, if the copyright holder fails to notify you of the
violation by some reasonable means prior to 60 days after the
cessation.
Moreover, your license from a particular copyright holder is reinstated
permanently if the copyright holder notifies you of the violation by some
reasonable means, this is the first time you have received notice of
violation of this License (for any work) from that copyright holder, and
you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the
licenses of parties who have received copies or rights from you under
this License. If your rights have been terminated and not permanently
reinstated, you do not qualify to receive new licenses for the same
material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a
copy of the Program. Ancillary propagation of a covered work occurring
solely as a consequence of using peer-to-peer transmission to receive a
copy likewise does not require acceptance. However, nothing other
than this License grants you permission to propagate or modify any
covered work. These actions infringe copyright if you do not accept this
License. Therefore, by modifying or propagating a covered work, you
indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically
receives a license from the original licensors, to run, modify and
propagate that work, subject to this License. You are not responsible for
enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an
organization, or substantially all assets of one, or subdividing an
organization, or merging organizations. If propagation of a covered work
results from an entity transaction, each party to that transaction who
receives a copy of the work also receives whatever licenses to the work
the party’s predecessor in interest had or could give under the previous
paragraph, plus a right to possession of the Corresponding Source of
the work from the predecessor in interest, if the predecessor has it or
can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights
granted or affirmed under this License. For example, you may not
impose a license fee, royalty, or other charge for exercise of rights
granted under this License, and you may not initiate litigation (including
a cross-claim or counterclaim in a lawsuit) alleging that any patent claim
is infringed by making, using, selling, offering for sale, or importing the
Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this
License of the Program or a work on which the Program is based. The
work thus licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or
controlled by the contributor, whether already acquired or hereafter
acquired, that would be infringed by some manner, permitted by this
License, of making, using, or selling its contributor version, but do not
include claims that would be infringed only as a consequence of further
modification of the contributor version. For purposes of this definition,
“control” includes the right to grant patent sublicenses in a manner
consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free
patent license under the contributor’s essential patent claims, to make,
use, sell, offer for sale, import and otherwise run, modify and propagate
the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express
agreement or commitment, however denominated, not to enforce a
patent (such as an express permission to practice a patent or covenant
not to sue for patent infringement). To “grant” such a patent license to a
party means to make such an agreement or commitment not to enforce
a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and
the Corresponding Source of the work is not available for anyone to copy,
free of charge and under the terms of this License, through a publicly
available network server or other readily accessible means, then you must
either (1) cause the Corresponding Source to be so available, or (2)
arrange to deprive yourself of the benefit of the patent license for this
particular work, or (3) arrange, in a manner consistent with the
requirements of this License, to extend the patent license to downstream
recipients. “Knowingly relying” means you have actual knowledge that, but
for the patent license, your conveying the covered work in a country, or
your recipient’s use of the covered work in a country, would infringe one or
more identifiable patents in that country that you have reason to believe
are valid.
If, pursuant to or in connection with a single transaction or arrangement,
you convey, or propagate by procuring conveyance of, a covered work,
and grant a patent license to some of the parties receiving the covered
work authorizing them to use, propagate, modify or convey a specific
copy of the covered work, then the patent license you grant is
automatically extended to all recipients of the covered work and works
based on it.
A patent license is “discriminatory” if it does not include within the scope
of its coverage, prohibits the exercise of, or is conditioned on the
non-exercise of one or more of the rights that are specifically granted
under this License. You may not convey a covered work if you are a
party to an arrangement with a third party that is in the business of
distributing software, under which you make payment to the third party
based on the extent of your activity of conveying the work, and under
which the third party grants, to any of the parties who would receive the
covered work from you, a discriminatory patent license (a) in connection
with copies of the covered work conveyed by you (or copies made from
those copies), or (b) primarily for and in connection with specific
products or compilations that contain the covered work, unless you
entered into that arrangement, or that patent license was granted, prior
to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any
implied license or other defenses to infringement that may otherwise be
available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot convey a
covered work so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you
may not convey it at all. For example, if you agree to terms that obligate
you to collect a royalty for further conveying from those to whom you
convey the Program, the only way you could satisfy both those terms
and this License would be to refrain entirely from conveying the
Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have
permission to link or combine any covered work with a work licensed
under version 3 of the GNU Affero General Public License into a single
combined work, and to convey the resulting work. The terms of this
License will continue to apply to the part which is the covered work, but
the special requirements of the GNU Affero General Public License,
section 13, concerning interaction through a network will apply to the
combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions
of the GNU General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies that a certain numbered version of the GNU General Public
License “or any later version” applies to it, you have the option of
following the terms and conditions either of that numbered version or of
any later version published by the Free Software Foundation. If the
Program does not specify a version number of the GNU General Public
License, you may choose any version ever published by the Free
Software Foundation.
If the Program specifies that a proxy can decide which future versions of
the GNU General Public License can be used, that proxy’s public
statement of acceptance of a version permanently authorizes you to
choose that version for the Program.
Later license versions may give you additional or different permissions.
However, no additional obligations are imposed on any author or
copyright holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above
cannot be given local legal effect according to their terms, reviewing
courts shall apply local law that most closely approximates an absolute
waiver of all civil liability in connection with the Program, unless a
warranty or assumption of liability accompanies a copy of the Program
in return for a fee.
END OF TERMS AND CONDITIONS
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL.
It also counts as the successor of the GNU Library Public License,
version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom
to share and change it. By contrast, the GNU General Public Licenses
are intended to guarantee your freedom to share and change free
software to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some
specially designated software packages--typically libraries--of the Free
Software Foundation and other authors who decide to use it. You can
use it too, but we suggest you first think carefully about whether this
license or the ordinary General Public License is the better strategy to
use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not
price. Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for
this service if you wish); that you receive source code or can get it if you
want it; that you can change the software and use pieces of it in new
free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid
distributors to deny you these rights or to ask you to surrender these
rights. These restrictions translate to certain responsibilities for you if you
distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a
fee, you must give the recipients all the rights that we gave you. You
must make sure that they, too, receive or can get the source code. If
you link other code with the library, you must provide complete object
files to the recipients, so that they can relink them with the library after
making changes to the library and recompiling it. And you must show
them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the
library, and (2) we offer you this license, which gives you legal
permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no
warranty for the free library. Also, if the library is modified by someone
else and passed on, the recipients should know that what they have is
not the original version, so that the original author’s reputation will not be
affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any
free program. We wish to make sure that a company cannot effectively
restrict the users of a free program by obtaining a restrictive license from
a patent holder. Therefore, we insist that any patent license obtained for
a version of the library must be consistent with the full freedom of use
specified in this license.
Most GNU software, including some libraries, is covered by the ordinary
GNU General Public License. This license, the GNU Lesser General
Public License, applies to certain designated libraries, and is quite
different from the ordinary General Public License. We use this license
for certain libraries in order to permit linking those libraries into non-free
programs.
When a program is linked with a library, whether statically or using a
shared library, the combination of the two is legally speaking a
combined work, a derivative of the original library. The ordinary General
Public License therefore permits such linking only if the entire
combination fits its criteria of freedom. The Lesser General Public
License permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does
Less to protect the user’s freedom than the ordinary General Public
License. It also provides other free software developers Less of an
advantage over competing non-free programs. These disadvantages
are the reason we use the ordinary General Public License for many
libraries. However, the Lesser license provides advantages in certain
special circumstances.
For example, on rare occasions, there may be a special need to
encourage the widest possible use of a certain library, so that it
becomes a de-facto standard. To achieve this, non-free programs must
be allowed to use the library. A more frequent case is that a free library
does the same job as widely used non-free libraries. In this case, there
is little to gain by limiting the free library to free software only, so we use
the Lesser General Public License.
In other cases, permission to use a particular library in non-free
programs enables a greater number of people to use a large body of
free software. For example, permission to use the GNU C Library in
non-free programs enables many more people to use the whole GNU
operating system, as well as its variant, the GNU/Linux operating
system.
Although the Lesser General Public License is Less protective of the
users’ freedom, it does ensure that the user of a program that is linked
with the Library has the freedom and the wherewithal to run that
program using a modified version of the Library.
The precise terms and conditions for copying, distribution and
modification follow. Pay close attention to the difference between a
“work based on the library” and a “work that uses the library”. The
former contains code derived from the library, whereas the latter must
be combined with the library in order to run.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other
program which contains a notice placed by the copyright holder or
other authorized party saying it may be distributed under the terms of
this Lesser General Public License (also called “this License”). Each
licensee is addressed as “you”.
A “library” means a collection of software functions and/or data
prepared so as to be conveniently linked with application programs
(which use some of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which
has been distributed under these terms. A “work based on the Library”
means either the Library or any derivative work under copyright law: that
is to say, a work containing the Library or a portion of it, either verbatim
or with modifications and/or translated straightforwardly into another
language. (Hereinafter, translation is included without limitation in the
term “modification”.)
“Source code” for a work means the preferred form of the work for
making modifications to it. For a library, complete source code means
all the source code for all modules it contains, plus any associated
interface definition files, plus the scripts used to control compilation and
installation of the library.
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of running a
program using the Library is not restricted, and output from such a
program is covered only if its contents constitute a work based on the
Library (independent of the use of the Library in a tool for writing it).
Whether that is true depends on what the Library does and what the
program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library’s
complete source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy an
appropriate copyright notice and disclaimer of warranty; keep intact all
the notices that refer to this License and to the absence of any
warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of
it, thus forming a work based on the Library, and copy and distribute
such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices
stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no charge
to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a table of
data to be supplied by an application program that uses the
facility, other than as an argument passed when the facility is
invoked, then you must make a good faith effort to ensure that, in
the event an application does not supply such function or table,
the facility still operates, and performs whatever part of its purpose
remains meaningful.
(For example, a function in a library to compute square roots has a
purpose that is entirely well-defined independent of the application.
Therefore, Subsection 2d requires that any application-supplied function
or table used by this function must be optional: if the application does
not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Library, and can be
reasonably considered independent and separate works in themselves,
then this License, and its terms, do not apply to those sections when
you distribute them as separate works. But when you distribute the
same sections as part of a whole which is a work based on the Library,
the distribution of the whole must be on the terms of this License,
whose permissions for other licensees extend to the entire whole, and
thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise the
right to control the distribution of derivative or collective works based on
the Library.
In addition, mere aggregation of another work not based on the Library
with the Library (or with a work based on the Library) on a volume of a
storage or distribution medium does not bring the other work under the
scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public
License instead of this License to a given copy of the Library. To do this,
you must alter all the notices that refer to this License, so that they refer
to the ordinary GNU General Public License, version 2, instead of to this
License. (If a newer version than version 2 of the ordinary GNU General
Public License has appeared, then you can specify that version instead
if you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy,
so the ordinary GNU General Public License applies to all subsequent
copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the
Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of
it, under Section 2) in object code or executable form under the terms
of Sections 1 and 2 above provided that you accompany it with the
complete corresponding machine-readable source code, which must
be distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange.
If distribution of object code is made by offering access to copy from a
designated place, then offering equivalent access to copy the source
code from the same place satisfies the requirement to distribute the
source code, even though third parties are not compelled to copy the
source along with the object code.
5. A program that contains no derivative of any portion of the Library,
but is designed to work with the Library by being compiled or linked
with it, is called a “work that uses the Library”. Such a work, in isolation,
is not a derivative work of the Library, and therefore falls outside the
scope of this License.
However, linking a “work that uses the Library” with the Library creates
an executable that is a derivative of the Library (because it contains
portions of the Library), rather than a “work that uses the library”. The
executable is therefore covered by this License. Section 6 states terms
for distribution of such executables.
When a “work that uses the Library” uses material from a header file
that is part of the Library, the object code for the work may be a
derivative work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked
without the Library, or if the work is itself a library. The threshold for this
to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure
layouts and accessors, and small macros and small inline functions (ten
lines or less in length), then the use of the object file is unrestricted,
regardless of whether it is legally a derivative work. (Executables
containing this object code plus portions of the Library will still fall under
Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute
the object code for the work under the terms of Section 6. Any
executables containing that work also fall under Section 6, whether or
not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link
a “work that uses the Library” with the Library to produce a work
containing portions of the Library, and distribute that work under terms
of your choice, provided that the terms permit modification of the work
for the customer’s own use and reverse engineering for debugging such
modifications.
You must give prominent notice with each copy of the work that the
Library is used in it and that the Library and its use are covered by this
License. You must supply a copy of this License. If the work during
execution displays copyright notices, you must include the copyright
notice for the Library among them, as well as a reference directing the
user to the copy of this License. Also, you must do one of these things:
a) Accompany the work with the complete corresponding machinereadable source code for the Library including whatever changes
were used in the work (which must be distributed under Sections
1 and 2 above); and, if the work is an executable linked with the
Library, with the complete machine readable “work that uses the
Library”, as object code and/or source code, so that the user can
modify the Library and then relink to produce a modified
executable containing the modified Library. (It is understood that
the user who changes the contents of definitions files in the Library
will not necessarily be able to recompile the application to use the
modified definitions.)
b) U
se a suitable shared library mechanism for linking with the Library.
A suitable mechanism is one that (1) uses at run time a copy of the
library already present on the user’s computer system, rather than
copying library functions into the executable, and (2) will operate
properly with a modified version of the library, if the user installs
one, as long as the modified version is interface-compatible with
the version that the work was made with.
c) Accompany the work with a written offer, valid for at least three
years, to give the same user the materials specified in Subsection
6a, above, for a charge no more than the cost of performing this
distribution.
d) If distribution of the work is made by offering access to copy from
a designated place, offer equivalent access to copy the above
specified materials from the same place.
e) Verify that the user has already received a copy of these materials
or that you have already sent this user a copy.
For an executable, the required form of the “work that uses the Library”
must include any data and utility programs needed for reproducing the
executable from it. However, as a special exception, the materials to be
distributed need not include anything that is normally distributed (in
either source or binary form) with the major components (compiler,
kernel, and so on) of the operating system on which the executable
runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions
of other proprietary libraries that do not normally accompany the
operating system. Such a contradiction means you cannot use both
them and the Library together in an executable that you distribute.
7. You may place library facilities that are a work based on the Library
side-by-side in a single library together with other library facilities not
covered by this License, and distribute such a combined library,
provided that the separate distribution of the work based on the Library
and of the other library facilities is otherwise permitted, and provided
that you do these two things:
a) Accompany the combined library with a copy of the same work
based on the Library, uncombined with any other library facilities.
This must be distributed under the terms of the Sections above.
b) G
ive prominent notice with the combined library of the fact that part
of it is a work based on the Library, and explaining where to find the
accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the
Library except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense, link with, or distribute the Library
is void, and will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from you under
this License will not have their licenses terminated so long as such
parties remain in full compliance.
9. You are not required to accept this License, since you have not signed
it. However, nothing else grants you permission to modify or distribute
the Library or its derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying or distributing
the Library (or any work based on the Library), you indicate your
acceptance of this License to do so, and all its terms and conditions for
copying, distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the
Library), the recipient automatically receives a license from the original
licensor to copy, distribute, link with or modify the Library subject to
these terms and conditions. You may not impose any further restrictions
on the recipients’ exercise of the rights granted herein. You are not
responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot distribute
so as to satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you may not
distribute the Library at all. For example, if a patent license would not
permit royalty free redistribution of the Library by all those who receive
copies directly or indirectly through you, then the only way you could
satisfy both it and this License would be to refrain entirely from
distribution of the Library.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply, and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or
other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software
distribution system which is implemented by public license practices. Many
people have made generous contributions to the wide range of software
distributed through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing to
distribute software through any other system and a licensee cannot impose
that choice.
This section is intended to make thoroughly clear what is believed to be
a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Library under this License may add an
explicit geographical distribution limitation excluding those countries, so
that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if
written in the body of this License.
13. The Free Software Foundation may publish revised and/or new
versions of the Lesser General Public License from time to time. Such
new versions will be similar in spirit to the present version, but may differ
in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library
specifies a version number of this License which applies to it and “any
later version”, you have the option of following the terms and conditions
either of that version or of any later version published by the Free
Software Foundation. If the Library does not specify a license version
number, you may choose any version ever published by the Free
Software Foundation.
14. If you wish to incorporate parts of the Library into other free
programs whose distribution conditions are incompatible with these,
write to the author to ask for permission. For software which is
copyrighted by the Free Software Foundation, write to the Free
Software Foundation; we sometimes make exceptions for this. Our
decision will be guided by the two goals of preserving the free status of
all derivatives of our free software and of promoting the sharing and
reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE
IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED
BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN
WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU.
SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest
possible use to the public, we recommend making it free software that
everyone can redistribute and change. You can do so by permitting
redistribution under these terms (or, alternatively, under the terms of the
ordinary General Public License).
To apply these terms, attach the following notices to the library. It is
safest to attach them to the start of each source file to most effectively
convey the exclusion of warranty; and each file should have at least the
“copyright” line and a pointer to where the full notice is found. one line
to give the library’s name and an idea of what it does.
Copyright (C) year name of author
This library is free software; you can redistribute it and/or modify it under
the terms of the GNU Lesser General Public License as published by
the Free Software Foundation; either version 2.1 of the License, or (at
your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 021101301 USA Also add information on how to contact you by electronic
and paper mail.
You should also get your employer (if you work as a programmer) or
your school, if any, to sign a “copyright disclaimer” for the library, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library
‘Frob’ (a library for tweaking knobs) written by James Random Hacker.
signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice.
OpenSSL LICENSE
Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software
must display the following acknowledgment: “This product includes
software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be
used to endorse or promote products derived from this software
without prior written permission. For written permission, please contact
openssl-core@openssl.org.
5. Products derived from this software may not be called “OpenSSL”
nor may “OpenSSL” appear in their names without prior written
permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following
acknowledgment: “This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.
org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ‘‘AS IS’’
AND ANY EXPRESSED OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.This product includes cryptographic software written by Eric
Young (eay@cryptsoft.com). This product includes software written by
Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights
reserved. This package is an SSL implementation written by Eric Young
(eay@cryptsoft.com). The implementation was written so as to conform
with Netscapes SSL. This library is free for commercial and noncommercial use as long as the following conditions are aheared to. The
following conditions apply to all code found in this distribution, be it the
RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL
documentation included with this distribution is covered by the same
copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.
com).
Copyright remains Eric Young’s, and as such any Copyright notices in
the code are not to be removed.
If this package is used in a product, Eric Young should be given
attribution as the author of the parts of the library used. This can be in
the form of a textual message at program startup or in documentation
(online or textual) provided with the package.Redistribution and use in
source and binary forms, with or without modification, are permitted
provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this
list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software
must display the following acknowledgement: “This product includes
cryptographic software written by Eric Young (eay@cryptsoft.com)” The
word ‘cryptographic’ can be left out if the rouines from the library being
used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative thereof) from
the apps directory (application code) you must include an
acknowledgement: “This product includes software written by Tim
Hudson (tjh@cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ‘‘AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.The licence and distribution terms for any publically
available version or derivative of this code cannot be changed. i.e. this
code cannot simply be copied and put under another distribution
licence [including the GNU Public Licence.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly
to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of
where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery
return system.
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungsv.com
www.samsungtechwin.com
www.samsungsecurity.com
www.samsungipolis.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325