SII LP-2050-MF User`s manual

Add to my manuals
30 Pages

advertisement

SII LP-2050-MF User`s manual | Manualzz

Wide Format Printer

Teriostar LP-2050 Series

Multifunction Model

LP-2050-MF

Printer Model

LP-2050

Quick Reference Guide

To operate your Printer correctly, read this manual carefully before use.

After reading the manual, keep it in a place where you can access it when required.

U00121382802

Preface

Your Printer is a Teriostar LP-2050 Series Wide Format Printer.

This manual describes the basic operation methods for both the LP-2050 and LP-2050-MF models. For more detailed information, see the User's Manuals on the supplied CD-ROM.

Table of Contents

Turning the Power On/Off …………………… 3

Power On ……………………………………………… 3

Power Off ……………………………………………… 3

Mode Buttons ………………………………… 3

Replacing the Paper …………………………… 4

Replacing the Toner Cartridge ………………… 6

Replacing the Waste Toner Bottle …………… 8

Replacing the Charger Unit …………………… 10

Replacing the Process Cartridge ……………… 12

Part Names ……………………………………… 14

Paper Jams ……………………………………… 16

Copying MF ………………………………… 20

Importing Images (Documents) to a Computer MF 21

Operating the Printer from a Computer MF 23

Troubleshooting ……………………………… 24

When an Error Message Appears …………………… 24

Smears on a Printout ……………………………… 24

Changing the Time Until Power Save Mode ……… 24

Automatic Paper Cutting After a Certain Time …… 24

Automatic Paper Cutting After Opening and Closing a Door ………………………………… 25

Changing the Print Density ………………………… 25

Wrinkles on Tracing Paper ………………………… 25

Selecting Paper to Match the Print Data …………… 25

Missing Print or Slow Data Reception ……………… 26

Service Representatives ……………………… 29

Disposal Method …………………………………… 29

Turning the Power On/Off

Power On

1 2

Power Off

1

Press down for

1 sec. or longer

2

Mode Buttons

3 z COPY button MF

Changes to copy mode, and the lamp at the button's left lights up. For more details, see the separate User's

Manual for Multifunction Printer Operation .

z SUBMIT button MF

Changes to submission mode, and the lamp at the button's left lights up. For more details, see the separate

User's Manual for Multifunction Printer Operation .

z SCAN button MF

Changes to scan mode, and the lamp at the button's left lights up. For more details, see the separate User's

Manual for Multifunction Printer Operation.

z PRINT button

Changes to print mode and enables printing.

z MENU button

Changes to menu mode, which enables the Printer setting specification.

2

3

4

1

Replacing the Paper

5

6

4

7

No Ok

8

9

60 cm

(23.63 inches)

11

10

T Replacing the Paper

5

2

1

Replacing the Toner Cartridge

4

5 x10 x10

6

3

6

8

T Replacing the Toner Cartridge

7

Disposing of Empty Toner Cartridges

Put the used toner cartridge into the bag provided in the box of the new toner cartridge, and dispose of it according to the local regulations.

7

1

Replacing the Waste Toner Bottle

2 x10

3

4

8

5 7

T Replacing the Waste Toner Bottle

6

Disposing of Used Toner Bottles

Dispose of the waste toner bottle according to the local regulations.

9

2

Replacing the Charger Unit

1 Press down for

1 sec. or longer

5

6

3

7

4

10

8

9

10

11

TIP

‘ The charger unit can be installed in either direction.

If lines or other defects appear on the printout, inverting the charger unit right and left sides may solve the problem.

11

T Replacing the Charger Unit

3

4

2

Replacing the Process Cartridge

1 Press down for

1 sec. or longer

5

6

7

12

8

9

10

11

12

13

13

16

14

15

T Replacing the Process Cartridge

Part Names

Front Side

Printer Model

Toner door

Multifunction Model

Scanner cover

Document table

Front door

Drawer for rolls 1 and 2

Drawer for rolls 3 and 4

14

T Part Names

Rear Side

Paper outlet slot

Latch button

Fuser unit drawer Process cartridge drawer

Paper outlet cover

15

Filter cover

Waste toner door

Paper Jams

The door requiring action is displayed, in accordance with the paper jam location.

Open the specified door and take the appropriate action to remove the paper jam.

3

Paper jam in a Roll paper drawer

1

Paper jam in the front door

1

2

16

2

3

Paper jam in the Fuser unit

1

T Paper Jams

2

3

When you cannot pull out the paper easily:

17

T Paper Jams

3

1

Paper jam in a roll paper drawer or front door

4

2

18

5

6

7

8

Original jam MF

1

2

3

4

5

T Paper Jams

19

Copying

MF

Press COPY

Set the original

Position the original facing down. Set it in the Printer aligned with the original width guide. The inserted original is automatically pulled into the Printer, and set.

20

3

4

5

2

1

Importing Images (Documents) to a Computer

MF

Double-click TerioStation.

Click the Scan tab.

Click Save Folder.

Select the destination folder to save the scanned data. Click OK.

Click Scan.

21

T Importing Images (Documents) to a Computer MF

6 Click Preferences.

7 Input the Printer IP address in the Assign host

name/IP address field. Click OK.

8 Set the scan conditions, and then click Scan.

9 Load the original.

Important

‹ If "Scanner is operating in another mode" is displayed, press SCAN on the operation panel.

‹ If "Color processing is not supported because the scanner being used is a dedicated monochrome device" is displayed, you cannot scan in color mode.

22

Operating the Printer from a Computer

MF

1 Start the web browser and enter "http://(IP address set on the Printer)" in the address field. Press Enter.

2 Click English.

3 Click an item from the left menu to check the settings or Printer status.

23

Troubleshooting

When an Error Message Appears

Take the action specified by the panel message.

Or see the User's Manual for Basic Printer

Operation , Chapter 4 .

Smears on a Printout

Replace the process cartridge.

(& page 12)

Changing the Time Until Power Save

Mode

Set Time Before Power Save in the Printer Engine menu.

Menu

Printer Engine

Time Before Power Save

15 minutes or

30 minutes or

60 minutes or

90 minutes or

235 minutes

Automatic Paper Cutting After a Certain

Time

Set Top Cut Timer in the Printer Engine menu.

Menu

Printer Engine

Roll 1 Top Cut Timer or

Roll 2 Top Cut Timer or

Roll 3 Top Cut Timer or

Roll 4 Top Cut Timer

Off or

30 minutes or

1 hour or

2 hours or

4 hours or

1 minute or

5 minutes or

10 minutes

24

T Troubleshooting

Automatic Paper Cutting After Opening and Closing a Door

Set Top Cut at Door Open to On in the Printer

Engine menu.

Menu

Wrinkles on Tracing Paper

Set Humidity for Tracing Paper to High Humidity in the Printer Engine menu.

Menu

Printer Engine

Top Cut at Door Open

On

Printer Engine

Humidity for Tracing Paper

High Humidity

Changing the Print Density

Set the Print Density in the Printer Engine menu.

Menu

Selecting Paper to Match the Print Data

Select Optimal at Paper Supply Mode.

Menu

Printer Engine

Print Density

Low or

Slightly Low or

Normal or

Slightly High or

High

PDL settings

Select the port and format

Paper Parameters

Paper Supply Mode

Optimal

25

T Troubleshooting

Missing Print or Slow Data Reception

Change the driver settings.

1 In Start Menu, open Devices and Printers.

4 Click Change in the operation mode of the driver.

2 Right-click the SII LP-2050 icon, and then click Printing Preferences.

5 Change the output process selection from

Process with Printer to Process with

Computer. Click OK.

3 Click the Options tab.

6 Click Apply.

26

7 Click OK.

T Troubleshooting

If the problem persists:

1 Perform steps 1 to 4 and open Driver

Operation Mode.

8 Print.

If the symptom persists, perform the following setting operation.

2 Set the resolution of the printer driver to

200dpi or 100dpi. Click OK.

27

T Troubleshooting

3 Click Apply.

4 Click OK.

5 Print.

The User's Manuals and driver are on the supplied CD-ROM.

28

Service Representatives

SIIT offers support to ensure you get the most from your Teriostar LP-2050 Series Printer. For details, contact your dealer or nearest service representative.

http://www.seiko-i.com/

Disposal Method

Dispose of the used toner cartridges and waste toner bottles according to the local regulations.

29

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

The CE mark, that shows that the products sold in the EU are conformed to the requirements of EC directive, is statutorily obliged to be affixed to the products.

In each directive, the scope of directive to be applied to equipment is explicitly defined. Our company’s product LP-2050 series conforms the EMC directive (2004/108/EC), low voltage directive (2006/95/EC) and

RoHS Directive 2011/65/EU.

Inquiry of CE mark:

Seiko Instruments GmbH

Siemensstraße 9, D-63263 Neu-Isenburg

Germany

Tel: +49-6102-297-0

Fax: +49-6102-297-320

Seiko I Infotech Inc.

8 Nakase 1-chome, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan

Phone : +81 43 211 1363

Fax : +81 43 211 8709

1-8, Nakase, Mihama-ku, Chiba-shi, Chiba, 261-8507, Japan

TEL: (043) 211-1310

U00121382802 July, 2013

Seiko I Infotech Inc., 2013

All rights reserved.

The contents of this manual may be changed without prior notice.

is a registered trademark of Seiko Instruments Inc.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals