OWNER'S MANUAL MODELNO. 247.795950 i z CRRFTSMRN® Caution: ReadandFollow AllSafetyRules andInstructions BeforeOperating This Equipment 5 HORSEPOWER 3 CUTTING STAGE MULCHING AND BAGGING CHIPPER-SHREDDER Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts SEARS,ROEBUCKAND CO., HoffmanEstates, IL 60179 U.S.A. Printed in U.S.A. 770-8473H 1/95 S, .FETY RULES WARNING: TO REDUCE SAFETY INSTRUCTIONS. THE PCTENTIAL FOR ANY INJURY, FAILURE TO COMPLY WITH THE COMPLY WITH INSTRUCTIONS THE FOLLOWING I MAY RESULT IN I I&,PERSONALINJURY. TRAINING • Read this owner's manual carefully in its entirety before attempting to assemble or operate this machin_. Be completely familiar with the controls and the proper Jse of this machine before operating it. Keep this manua in a safe place for future and regular reference and fc" ordering replacement parts. • Children must never be allowed to operate this e,luipment. • No one should operate this unit while intoxicated or while taking medication that impairs the senses or re_Lctions. • This equipment should never be operated in t_e vicinity of children, pets or other persons. • Never run your machine in an enclosed ar,,,a as the exhaust from the engine contains carbon mono_ ida, which is an odorless, tasteless and deadly poisonous g is. • Never place your hands or any part of your bod_' or clothing inside the feeding chamber, discharge chul_, or near any moving part while the machine or engine is "unning. • If it is necessary for any reason to inspect or repair the feeding chamber or any part of the machine wh_ re a moving part can come in contact with your body c" clothing, stop the machine, allow it to cool, disconnect the spark plug wire from the spark plug and move it awa, r from the spark plug before attempting such inspection or r ;pair. PREPARATION • Wear safety glasses provided with your unit wh le operating the chipper-shredder to prevent injury from _ny material which may be ejected out of the openings. • Wear proper apparel. Avoid wearing loose fittin!l clothing. Wear gloves when handling material. • HANDLE GASOLINE WITH CARE as it is an _xtremely flammable fuel. • Check the fuel before starting the engine. Do ilot fill the fuel tank indoors, while the engine is running, el while the engine is still hot. Turn the unit off and let the engine cool before refueling. • Fuel your chipper-shredder in a clean arez.. Do not smoke while refueling. • Fuel tank cap must be secure at all times excE:pt during refueling. • Avoid spilling gasoline or oil. Wipe the unit cle]n of any spilled fuel or oil. • Store fuel and oil in approved containers, away from heat or open flame, and out of reach of children. • This machine should be operated only upon a lew _1surface. • Assure that all screws, nuts and bolts and other fasteners are properly secured. OPERATION • When feeding shreddable material into this e_luipment, be extremely careful that pieces of metal, rock_, bottles, cans or other foreign objects are not included. Personal injury or damage to the machine could result. & • • • • • • • • • • • if the cutting mechanism strikes any foreign object or if your machine should start making an unusual noise or vibration, immediately stop the engine, disconnect the spark plug wire from the spark plug and move it away from the spark plug. Allow the machine to stop and take the following steps: Inspect for damage. Replace or repair any damaged parts. Check for any loose parts and tighten to assure continued safe operation. The engine must be kept clean of debris and other accumulations. Do not allow an accumulation of processed material to build up in the discharge area as this will prevent proper discharge and can result in kick-back from feed opening. Never place your hands or any other part of your body or clothing inside the feeding chamber, discharge chute or near any moving part while the engine is running. Keep all guards and deflectors in place and in good working condition to assure continued safe operation. Always stand clear of the discharge area when operating this machine. Keep your face and body back from the feed opening to avoid accidental bounce back of any material. Do not over-reach. Keep proper balance and footing at all times. The engine governor settings on your machine must not be altered, changed, or tampered with. The governor controls the maximum safe operating speeds and protects the engine and all moving parts from damage caused by overspeed. Do not transport machine while engine is running. Do not operate engine if air cleaner or cover directly over carburetor air intake is removed, except for adjustment. Removal of such parts could create a fire hazard. MAINTENANCE AND STORAGE • When this equipment is stopped for servicing, inspection, storage or to change an accessory, make sure the spark plug wire is disconnected from the spark plug and moved away from the spark plug. The machine should be allowed to cool down before making such inspection, adjustments, service, etc. Maintain your machine with care and keep it clean for the best and continued safe operation. • Do not use flammable solutions to clean the air filter. • When not in use, your machine should be stored out of the reach of children. Keep where gasoline fumes will not reach an open flame or spark. For long periods of storage, refer to the "Storage" section of this manual. L]OK FOR THIS SYMBOL TO POINT OUT II_IPORTANT SAFETY PRECAUTIONS. ITI lYEANS--ATTENTION!!! BECOME ALERT!!!] Y Z)URSAFETY IS INVOLVED. I ] CONGRATULATIONS on your purchase of a Sears Craftsman Chipper-Shredder. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest Sears Service Center/ Department in the United States. We have competent, welltrained technicians and the proper tools to service or repair this unit. Please read and retain this manual. The instructions will enable you to assemble and maintain your chipper-shredder properly. Always observe the "SAFETY RULES." MODEL NUMBER 5.0 Displacement: 12.57 cu. in. Engine Oil: API Classification SAE 30 (1-1/4 Pints) SG or SH Fuel Capacity: 1 Gallon (Unleaded) Champion J19LM (or Equivalent) 247.795950 SERIAL NUMBER Magnetron ® Ignition Air Gap: DATE OF PURCHASE Tire Pressure: YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. CUSTOMER • Horsepower: Spark Plug (Gap .030 in.): THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A LABEL ATTACHED TO THE FRAME OF THE CHIPPER-SHREDDER. • • PRODUCT SPECIFICATIONS RESPONSIBILITIES Read and observe the safety rules. Follow a regular schedule in maintaining, and using your chipper-shredder. Follow the instructions under "Customer ibilities" Manual. and "Storage" sections of this caring for ResponsOwner's .0125 in. 24 p.s.i. MAINTENANCE AGREEMENT A Sears Maintenance Agreement is available on this product. Contact your nearest Sears store for details. WARNING: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a 8park arrester meeting applicable local or state laws (if any), If a spark arrester is used, it should be maintained in effective working order by the operator. Jn the State of California the above is required by law ISection 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears Authorized Service Center (See the REPAIR PARTS section of this manual.) WARRANTY FULL ONE YEAR WARRANTYON CRAFTSMANGAS CHIPPER-SHREDDER For one year from the date of purchase, when this Craftsman chipper-shredder is maintained, lubricated, and tuned up according to the operating and maintenance instructions in the operator's manual, Sears will repair, free of charge, any defect in material or workmanship. This warranty excludes the blades, chipper blades, which are expendable parts and become worn during If this chipper-shredder is used for commercial flails, air cleaners, normal use. or rental purposes, spark this warranty plugs, catcher applies bags and tires, for only 30 days from the date of purchase. WARRANTY SERVICE IS AVAILABLE UNITED STATES. THIS WARRANTY STATES. This warranty gives you specific SEARS BY CONTACTING THE NEAREST SEARS SERVICE CENTER IN THE APPLIES ONLY WHILE THIS PRODUCT IS IN USE IN THE UNITED legal rights, ROEBUCK and you may also have other AND CO., DEPT. 817WA, HOFFMAN rights which vary from state to state. ESTATES, IL 60179 TABI.E OF CONTENTS SAFETY RULES ......................................................... 2 PRODUCT SPECIFICATIONS ................................... 3 WARRANTY ............................................................... 3 INDEX ......................................................................... 4 ACCESSORIES ......................................................... 4 ASSEMBLY ............................................................ 5-7 OPERATION ........................................................ 7-10 CUSTOMER RESPONSIBILITIES ..................... 11, 12 STORAG E ................................................................ 13 SERVICE AND ADJUSTMENT ........................... 13-15 TROUBLE SHOOTING ............................................. 16 PARTS ORDERING/SERVICE ................................. 16 REPAIR PARTS--CHIPPER-SHREDDER ........ 17, 18 REPAIR PARTS--ENGINE ................................. 19-23 INDEX A Accessories ............................................................... 4 Adjustments: Carburetor ............................................................ 15 Engine Speed ...................................................... 15 Throttle ................................................................. 15 Assembly Instructions: Catcher Bag ........................................................... 6 Chute Deflector ...................................................... 6 Hopper Assembly .................................................. 6 Catcher Bag ....................................................... 6, 7 C Catcher Bag ........................................................... 6, 7 Controls ..................................................................... 7 Customer Responsibilities .............................. E 3, 11,12 Engine: Maintenance ................................................... 11, Starting ................................................................. Stopping .................................................................. Storage ................................................................. F Fuel ............................................................................. L Lubrication ................................................................ 12 10 8 13 9 11 M Maintenance: Agreement ............................................................. 3 Schedule ............................................................... 11 Engine ............................................................. 11, 12 Chipper-Sh redder ................................................ 11 O Oil ............................................................................... 9 Operating Tips ............................................................ 8 R Repair/Replacement Parts .................................. 17-23 Responsibilities, Customer .............................. 3, 11-13 S Safety Rules ............................................................... 2 Sharpening ......................................................... 14, 15 Service Recommendations ....................................... 11 Spark Plug ................................................................ 12 Specifications .............................................................. 3 Storage ..................................................................... 13 T Table of Contents ....................................................... 4 Trouble Shooting ....................................................... 16 U Unclogging .......................................................... 13, 14 Unpacking ................................................................... 5 W Warranty .................................................................... 3 ACCESSORIES These accessories were available when the chipper-shredder was purchased. They are also available at most Sears retail outlets, catalog and service cel_ters. Most Sears stores can order repair parts for you, when you provide the model number of your chipper-shl edder. ENGINE Spark Plug Air Filter Muffler ngine Oil r _===1 CHIPPER-SHREDDER Gas Can Stabilizer Tow Hitch Kit ASSEMBLY INSTRUCTIONS iMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL in the engine. After assembly, see operation section of this manual for proper fuel and engine oil recommendations. Flat --_/1_ Washer ( ( 'j | 5/16" I.D. 'q" Hex Lock Nut 5/16-18 Thread NOTE: To determine right and left hand sides of your chipper-shredder, stand behind the unit with the engine the farthest away from you. See figure 6. Your chipper-shredder has been completely assembled at the factory, except for the hopper assembly (hopper hood and upper leaf ramp section have been sub-assembled), upper guide assembly, chute deflector and the catcher bag, The hardware pack safety glasses and bottle of oil are also included in the carton. The hardware pack contains the parts shown in figure 1 (shown full size). TOREMOVE CHIPPER-SHREDDER FROMCARTON Hex Bolt 5/16-18 x 8-3/8" Long Cut the corners of the carton. Remove all packing inserts. Roll chipper-shredder out of the carton. Make certain all parts and literature have been removed before the carton is discarded. TOOLS REQUIREDFOR ASSEMBLY (1) Phillips Screwdriver (2) 1/2" or Adjustable Wrenches 12/ 7116" or Adjustable WrenchesFunnel Machine Screws 1/4-20 x 1/2" Long Hex Lock Nuts 1/4-20 Thread FIGURE 1. Spacers: Housiltg Assem aly 13olt 3hute D .=flector He]( Nut Hand Knob FIGURE 2. Stop Hopper !-_F--_ Pivot _ Door //_ /! // // t/ II II II11 ! Washer "_/_ _o / "_'_Y_\ \/ t l /l_'_I _ _,-_\_ _ ,_ _t_ J I \llll _ /// /Jill XHexBolt I \\1 II/ Inset /// Guide FIGURE 3. fill 8-3/8"Long \\1 °Ill Y Flat Washer _ Hex Lock Nut Hopper Pivot Door Bar Release Bar 3pper _uiae A.,;sembly Hopper Asstimbly t l pper Leaf Ilamp S .=ction Remove T russ Screw ant Nut Guide (Asseml de Assembly First) FIGURE 4. Drawstr ng .Plunger FIGURE 5. HOWTOSET-UPYOURCHIPPER-SHREDDER WIRE IS DISCONNECTED AND MOVED AWAY MAKE CERTAIN FROM THE THE SPARK SPARK PLUG BEFORE ASSEMBLING THE CHIPPERSHREDDER. REFER TO FIGURE 13, PAGE 10. <'-ATTACHING THE CHUTE DEFLECTOR • Remove the hand knobs and cupped washers from each side of the discharge opening on the left side of the chipper-shredder. • Remove hex lock nut, two spacers and hex bolt using two 7/16" wrenches from inside the hinge on top of the housing assembly. Do not remove one spacer from the hex bolt. • Place the chute deflector in position on the discharge opening. Insert hex bolt and spacer through hinge on chute deflector and housing (spacer fits inside of hinge). See figure 2. • Place second spacer over hex bolt, inside other part of hinge. Secure with hex lock nut. Tighten securely. • Secure both sides of chute deflector to housing using hand knobs and cupped washers (cupped side of washers go against chute deflector). _-ATTACHING THE UPPER GUIDE ASSEMBLY Grasp the upper guide assembly from the sides and squeeze in and slide it over the inlet guide so the edges are under the stop washers. Adjust so the holes in the upper guide assembly are aligned with the holes in the inlet guide. Insert the hex bolt, 8-3/8" long through the upper guide assembly and the inlet guide. Secure with flat washer and lock nut. NOTE: Make certain the upper guide assembly can pivot by lifting it up until it locks in the raised position. If it does not pivot freely, loosen the hex lock nut a turn or two and test. <-ATTACHING THE HOPPER ASSEMBLY Your chipper-shredder has been shipped with the upper leaf ramp section attached to the hopper assembly. See figure 4. Attach the hopper assembly to the upper guide assembly as follows. Be certain to place heads of all truss machine screws inside of hopper assembly. • Remove one truss machine screw and nut from each side of hopper assembly as shown in figure 4. Push hopper pivot door down inside lower part of hopper as you place hopper assembly (both pieces) inside upper guide assembly. Replace truss screws and nuts just removed, using the hole shown in figure 4, one on each side. Tighten finger tight only. NOTE: You may have to squeeze in the sides of the hopper to start the screws. NOTE: If you have difficulty aligning the hole, loosen the two screws on the upper end of the hopper assembly. • Place the six truss machine screws and nuts found in hardware pack in the remaining holes of hopper assembly, alternating sides of the unit and tightening finger tight only. • After assembling all eight screws, tighten them securely. <-ATTACHING THE CATCHER BAG Your chipper-shredder is equipped with a catcher bag to catch the shredded material. ,_ • To attachthe bag, placethe openingOfthe bag overthechutedeflectorso it completely coversthe chuteopening.Depressthe plungeron the drawstring,andpull on the drawstringuntilthe bag is tightaroundthechuteopening.Releaseplungerto lockit intoposition.Seefigure5. TIRES Recommended tire pressure is 24 p.s.i. OPERATION KNOW YOUR CHIPPER-SHREDDER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHIPPER-SHREDDER. Compare the illustrations with your chipper-shredder to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Hopper Assembly Release Bar Oil Fill Chipper Dipstick Chute Fuel Tank Chute Choke Engine ! Switch Bag Handle Throttle Control / FIGURE 6. Front of Chipper-Shredder MEETS ANSI SAFETY STANDARDS Sears chipper-shredders conform to the safety standard B71.6-1982 of the American National Standards Institute. OPERATINGCONTROLS RELEASE BAR--Used to release the hopper when raising or lowering, See figure 6, CHOKE LEVERmUsed to enrich the fuel mixture in the carburetor when starting a cold engine, See figure 6 and 14. STARTER HANDLE--Used engine. See figure 6. to manually start the ENGINE SHUT-OFF SWITCHmUsed engine. See figures 6 and 14. to stop the FUEL SHUT-OFF VALVE--Used to stop the flow of fuel into the carburetor. See figure 14. THROTTLE CONTROL--Permits selection of fast or slow engine speed. See figures 6 and 14. BEFORE USING YOUR CHIPPER-SHREDDER, AGAIN REFER TO THE "SAFETY PAGE 2 OF THIS MANUAL. ALWAYS BE CAREFUL. RULES" AS SHOWN ON The operation of any chipper-shredder can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear the safety glasses provided with the chipper-shredder or eye shields before chipping or shredding, or while performing any adjustments or repairs. We recommend Wide Vision Safety Mask for over spectacles or standard glasses available at Sears Retail or Catalog Stores. TOSTOPENGINE • Move engine shut-off switch to OFF positon. figure 6 and 14. \ See • Disconnect spark plug wire and move a_ay from spark plug to prevent accidental startir g while equipment is unattended. See figure 13. No Larger Than 1/2" Diameter Recommended) Or 1" Diameter (Maximum) • Close fuel shut-off valve when equipment s not in use to prevent fuel leakage. See figure 14. HOWTOUSEYOURCHIPPER-SHREDDER Do not attempt to shred or chip any material other than vegetation found in a normal yard (i.e., blanches, leaves, twigs, etc.). & WARNING: THE CHIPPER-SHREDDER DISCHARGES MATERIALS WITH CONSIDERABLE VELOCITY. KEEP AWAY FROM THE AREA AROUND THE CHUTE DEFLECTOR. ALWAYS STOI } THE ENGINE AND DISCONNECT THE SPARK PLUG WIRE WHEN REMOVIHG OR ATTACHING THE BAG WHEN CHI,NGING CONTAINERS OR WHEN REMOVII4G THE SHREDDED MATERIAL. WEAR SAFETY GLASSES AND GLOVES WHENEVER USING YOUR CHIPPER-SHREDDER. The chipper-shredder methods of operation. Hopper Assembly FIGURE 7. • Leaves and small twigs can be raked into the hopper assembly when the hopper assembly is lowered to the ground. See figure 8. Small branches up to 1/2" diameter (recommended) or 1" diameter (maximum) can also be fed into the hopper assembly in this position. See figure 9. is designed for three ,]ifferent • Leaves and small branches up to 1/2" d ameter (recommended) or 1" diameter (maximum) can be fed into the hopper assembly when it i_; in the raised position. See figure 7. If it become_ necessary to push material into the chipper-sl" redder, use a small diameter stick--NOT YOUR HANDS. FIGURE 8. The stick should be small enough that it will be ground up if gets into the impeller assembly / / & / J WARNING: DO NOT PUT MATERIAL LARGER THAN 1/2" IN DIAMETEFI (RECOMMENDED) or 1" DIAMETER (MAXIMUM) INTO THE HOPPER ASSEMBLY. MATERIAL UP TO A MAXIMUM OF 3" IN DIAMETER MAY BE FED INT3 THE CHIPPER CHUTE. DO NOT ATTEI_IPT TO SHRED OR CHIP ANY MATERIAL LARGER THAN 3" IN DIAMETER. PER._ONAL INJURY OR DAMAGE TO THE MliCHINE COULD RESULT. No Larger Than 1/2" Diameter (Recommended), Or 1" Diameter (Maximum) FIGURE 9. • To lower the hopper assembly, use one hand to grasp the handle at the top of the hopper assembly and lift slightly. Pull up on the release bar, and lower the hopper assembly to the ground. Release the bar. See figure 10. Hopper Assembly GASAND 01LFILL-UP(OilPacked withUnit) OIL Only use high quality detergent oil rated with API service classification SF, SG or SH. Select the oil's viscosity grade according to your expected operating temperature. Colder < 32°F = Warmer 5W30 Release Bar FIGURE 10. • Bulky material, such as stalks or heavy branches, up to 3" in diameter, should be fed into the chipper chute. See figure 11. WARNING: MAKE CERTAIN NOT USE. DOOR PER IN CHUTE SAE 30 NOTE: Although multi-viscosity oils (5W30, 10W30, etc.) improve starting in cold weather, these multiviscosity oils will result in increased oil consumption when used above 32°F. Check your oil level more frequently to avoid possible engine damage from running low on oil. • Fill engine with oil as follows. Remove oil fill dipstick. See figure 12. With chipper-shredder level, use a funnel to fill engine with oil to FULL mark on dipstick. Capacity is approximately 1-1/4 pints (20 oz.). Be careful not to overfill. Tilt chipper-shredder toward the left (from behind the hopper), then relevel. Check oil level. Refill to FULL mark on dipstick if necessary. Replace dipstick and tighten. THE CHIP- IS CLOSED WHEN 3" Maximum Diameter Oil Fill Dipstick Oil Drain Drain FIGURE 11. Chipper Chute IMPORTANT: There is a flail screen located inside the housing in the discharge area. If the flail screen becomes clogged, remove and clean as instructed in the Service and Adjustments section. For best performance, it is important to keep the shredding blade and the chipper blades sharp. If the composition of the material being discharged changes (becomes stringy, etc.) or if the rate at which the material is discharged slows down considerably, it is likely that the shredding blade and/or chipper blades are dull and need to be replaced. Refer to Service and Adjustments section. FIGURE 12. GAS • Remove fuel cap and fill fuel tank with about 1 gallon of clean, fresh, lead-free grade automotive gasoline. DO NOT use Ethyl or high octane gasoline. Be certain container is clean and free from rust or foreign particles. Never use gasoline that may be stale from long periods of storage in the container. Replace fuel cap. 1/2 INCH OF TOP OF FUEL TANK TO WARNING: DO NOTAND FILLTO CLOSER PREVENT SPILLS ALLOW THAN FOR FUEL EXPANSION. IF GASOLINE IS ACCIDENTLY SPILLED, MOVE CHIPPERSHREDDER AWAY FROM AREA OF SPILL. AVOID CREATING ANY SOURCE OF IGNITION UNTIL GASOLINE VAPORS HAVE DISAPPEARED. Check the fuel level periodically to avoid running out of gasoline while operating the chipper-shredder. If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit before it can be restarted. Refer to "Removing the Flail Sc'een" in SERVICE AND ADJUSTMENT section. • Place the throttle control lever in FAST position. See figure 14. NOTE: If the throttle control lever fails to stay in the desired position or if it is hard to move, refer to the service and adjustment section. • Move choke lever to CHOKE position. • Place the engine shut-off switch in ON position. See figure 14. • Grasp starter handle (see figure 13) and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly. NOTE: A noise will be heard when finding the start of the compression cycle. This noise is caused by the flails and fingers which are part of the shredding mechanism falling into place, and should be expected. In addition, the flails and fingers will be noisy after the engine is started, until the impeller reaches full speed. • Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on start handle. Let rope rewind slowly. Do not let starter handle snap back against starter. NOTE: To prevent the unit from sliding, place your foot against the tire. • Repeat preceding two instructions until engine fires. When engine starts, move choke lever on engine halfway between CHOKE and RUN. NOTE: If engine does not fire after three attempts, move choke lever halfway between CHOKE and RUN )osition and try a ain. See figure 14. WARNING: EXPERIENCE INDICATES THA1 ALCOHOL BLENDED FUELS (CALLED GASOI-OL OR USING ETHANOL OR METHANOL) CAN AITRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE. TO AVOID ENGINE PROBLEMS, THE FUEL S_STEM SHOULD BE EMPTIED OR TREATED WITH FUEL STABILIZER BEFORE STORAGE FOR 3( DAYS OR LONGER. USE FRESH FUEL NEXT SE!ASON. SEE "STORAGE" SECTION FOR ADDIIlONAL INFORMATION. NEVER USE ENGINE OR CARBURETOR (;LEANER PRODUCTS IN THE FUEL TANK OR PERMANENT DAMAGE MAY OCCUR. Spark I_lug, Wire and Boot Fuel Under (;over) On Muffler Oil Fill Di _stick oO;,on Fuel Shut-Off Valve Throttle Engine Shut-Off Switch Handle FIGURE 13. TO STARTENGINE & (_hoke' _hoke Run J Ixl Position_l f I WARNING: BE SURE NO ONE OTHER THAN THE OPERATOR IS STANDING NEAR THE CHIPPER-SHREDDER WHILE STARTING OR OPERATING. D() NOT OPERATE THIS CHIPPER-SHREDDER UNLESS THE CHUTE DEFLECTO:I HAS BEEN PROPERLY INSTALLED ._ND IS SECURED WITH THE HAND KNOB.€;. CHOKE FIGURE 14. TO STOP ENGINE • Move throttle control lever to SLOW position. • Move engine shut-off switch to OFF position. See figure 14. • Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended. • Close fuel shut-off valve when equipment is not in use to prevent fuel leakage. • Open cover (on top of fuel tank) and attach spark plug wire and rubber boot to spark plug if necessary. Replace cover. See figure 13. • Open fuel shut-off valve by turning in dire(:tion of arrow. See figure 14. 10 CUSTOMER RESPONSIBILITIES .c°.c.°o°.° ,,,., F,,N OLATES / V I-- o Oil Pivot Points _3 O 8: Clean Shredder "_ _/ 13. Check Engine Oil _J Change Engine Oil 1,1.1 _ z Service Air Cleaner _/ z uJ Clean Engine Cylinder _/ _' Spark Plug _4' _r Muffler _/ CHECK Colder GENERALRECOMMENDATIONS AND DISCONNECT THE SPARK PLUG WARNING: ALWAYSPERFORMING STOP THE ENGINE WIRE BEFORE ANY MAINTENANCE OR ADJUSTMENTS. • Periodically are tight. check all fasteners _< 32°F 5W30 _ Warmer SAE 30 NOTE: Although multi-viscosity oils (SE30, 10W30, etc.) improve starting in cold weather, these multi- viscosity oils will result in increased oil consumption when used above 32°F. Check your oil level more frequently to avoid possible engine damage from running low on oil. and be sure they • Follow the Maintenance Schedule above. CHIPPER-SHREDDER Your four-cycle engine will normally consume some oil--therefore, check engine oil level regularly approximately every five hours of operation and before each usage. Stop engine and wait several minutes before checking oil level. With engine level, the oil must be to FULL mark on dipstick (refer to figure 12). Change engine oil after the first five hours of operation, and every twenty-five hours thereafter. LUBRICATION Lubricate the pivot points on the release bar, hopper assembly, chute deflector and chipper chute once a season using a light oil. CLEANING • The chipper-shredder may be cleaned by running water from a hose through the hopper assembly and chipper chute with the engine running. Allow the chipper-shredder to dry thoroughly. To Drain Oil: • • Wash the bag periodically with water. Allow to dry thoroughly in the shade. Do not use heat. Drain oil while engine is warm. a. Remove oil drain plug. Refer to figure 11. Catch oil in a suitable container. ENGINE b. When engine is drained of all oil, replace drain plug securely. • Refill with fresh oil. Refer to GAS AND OIL FILLUP section. ENGINE OIL Only use high quality detergent oil rated with API service classification SF, SG or SH. Select the oil's viscosity grade according to your expected operating temperature. • Replace dipstick. 11 AIR CLEANER The air cleaner prevents damaging dirt, dust, etc., from entering the carburetor and being forced into the engine and is important to engine life _ nd performance. Never run your engine without pletely assembled. To Service Air Cleaner: FIGURE 16. air cleaner com- CLEAN ENGINE Clean engine periodically. Remove dirt and debris with a cloth or brush. Cleaning with a forceful spray of water is not recommended as water could contaminate the fuel system. Service pre-cleaner after every 25 hours of use, or at least once a season. Service cartridge every 130 hours of use, or at least once a season. Service pn;-cleaner and cartridge more often under dusty conditions. Yearly or every 25 hours, whichever occurs first, remove the blower housing and clean the areas shown in figure 17 to avoid overspeeding, overheating and engine damage. Clean more often if necessary. • Loosen air cleaner cover screws. Remo-e cover and air cleaner assembly from base. See fi jure 15. • Remove air cleaner and disassemble. assembly from inside cover • To service foam pre-cleaner: Remove pre.cleaner. Wash in liquid detergent and water. Squee_,e dry in a clean cloth. Saturate in engine oil. Squeeze in a clean, absorbent cloth to remove all excess oil. If pre-cleaner is very dirty, replace it. ,_ FLER AREA TO REMOVE ALL GRASS, WARNING: PERIODICALLY DEBRIS. CLEAN MUFDIRT AND COMBUSTIBLE Clean Out Chaff and Dirt • To service cartridge: Clean by tapping gently on a flat surface. If very dirty, replace. Do not oil cartridge. NOTE: Do not use petroleum solvents (e.g. k_;rosene) or pressurized air to clean cartridge. They wll cause cartridge to deteriorate. • Reassemble retainer on pre-cleaner and _:artridge (screen side of pre-cleaner toward c_lrtridge pleats). Place assembly into cover. FIGURE 17. SPARK PLUG The spark plug should be cleaned and the gap reset to .030" at least once a season or every 50 hours of operation. See figure 18. Spark plug replacement is recommended at the start of each season. Refer to engine parts list for correct spark plug type. • Insert tabs on cover into slots in base and tighten cover screws securely. Retainer Pre-Cleaner Cartrid( Cover Slot Base NOTE: Do not sandblast spark plug. Spark plug should be cleaned by scraping or wire brushing and washing with a commercial solvent. .030" Feeler Gauge Screws Spark Plug FIGURE 18. FIGURE 15. MUFFLER Do not operate the chipper-shredder without a muffler or tamper with the exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect periodically, and replace if necessary. If your engine is equipped with a spark arrester screen assembly, remove every 50 hours for cleaning and inspection. Replace if damaged. FUEL FILTER Your engine is equipped with a replaceable in, line fuel filter. Replace the fuel filter every season. See figure 16. Refer to engine parts list for correct repl_Lcement filter. 12 STORAGE • Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. • Start the engine and let it run until the fuel lines and carburetor are empty. • Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. • Use fresh fuel next season. WITH FUEL IN THE FUEL TANK INSIDE WARNING: STORE MACHINE OF BUILDINGNEVER WHERE FUMES MAY REACH AN OPEN FLAME OR SPARK, OR WHERE IGNITION SOURCES ARE PRESENT SUCH AS HOT WATER AND SPACE HEATERS, FURNACES, CLOTHES DRYERS, STOVES, ELECTRIC MOTORS, ETC. NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer. • Drain all the oil from the crankcase (this should be done after the engine has been operated and is still warm) and refill the crankcase with fresh oil. NOTE: A yearly check-up by your local Sears Service Center is a good way to make certain your chippershredder will provide maximum performance for the next season. CHIPPER-SHREDDER • Clean the chipper-shredder Drain the fuel tank. • If you have drained the fuel tank, protect the inside of the engine as follows. Remove spark plug, pour approximately 1/2 ounce (approximately one tablespoon) of engine oil into cylinder and crank slowly to distribute oil. Replace spark plug. thoroughly. • Wipe unit with an oiled rag to prevent rust (use a light oil or silicone). ENGINE IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE. OTHER • Do not store gasoline from one season to another. • Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems. • Store unit in a clean, dry area. Do not store next to corrosive materials, such as fertilizer. NOTE: If storing in an unventilated or metal storage shed, be certain to rustproof the equipment by coating with a light oil or silicone. SERVICE & ADJUSTMENT WARNING: ALWAYS STOP ENGINE AND Loosen the two hand knobs on each side of the chute deflector. Lift the chute deflector up, and tie it out of the way. MOVE IT AWAY FROMPLUG SPARK DISCONNECT SPARK WIRE PLUG AND BEFORE PERFORMING ANY ADJUSTMENTS OR REPAIRS. • REMOVING THE FLAIL SCREEN Remove two hairpin clips from the clevis pins which extend through the housing. Remove the clevis pins. Lift the flail screen from inside the housing. See figure 19. If the discharge area becomes clogged, remove the flail screen and clean area as follows. • Clean the screen by scraping water. Reinstall the screen. • Stop the engine, make certain the chipper-shredder has come to a complete stop and disconnect spark plug wire from the spark plug before unclogging the chute. NOTE: Be certain to reassemble the flail screen with the curved side down as shown in figure 19. 13 or washing with Replace or sharpen blades. If sharpening, make certain to remove an equal amount from each blade. Reassemble in reverse order. .,, Chute Deflector _! "a',.'° _\ _ _\ _ _ Clips, _1 _--_i Clevis 1\ Make certain blades are reassembled with the sharp edge facing the direction shown in figure 19 (sharp edge is assembled toward the slotted opening in the impeller assembly). Torque bolts and nuts to 250-350 inch pounds. t_ /1 7F-D Washers(.,._'_.'_\\\ / _\ /_i/ SHREDDING BLADE The shredding blade may be removed for sharpening or replacement as follows. • Disconnect spark plug wire and move it away from spark plug. sFlai/n • Lower the hopper assembly. Block up the housing. See figure 21. • Remove the six hex lock nuts and lock washers from the housing weld bolts using a 1/2" wrench. Separate the chipper-shredder into two halves. Hand Knob., FIGURE 19. • Remove the back-up plate. SHARPENINGOR REPLACINGTHE BLADES NOTE: When reassembling, make certain the opening on the back-up plate is toward the bottom of the unit. The back-up plate may be reversed to provide a new cutting edge. CHIPPER BLADES • Disconnect spark plug wire and move it away from spark plug. • Remove the flail screen as instructed in _revious section. • Remove the chipper chute by removing three hex nuts and washers. A 1/2" wrench is requi_'ed. See figure 19. Allen Screws NOTE: When reassembling, the cupped washer goes on the bottom of the chipper chute with the cupped side against the chute. Pipe • Rotate the impeller assembly by hand Lntil you locate one of the chipper blades in the chipper chute opening. Remove the blade, using a 3/16" allen wrench on the outside of the blade ._nd 1/2" wrench on the impeller assembly (inside the housing). See figure 20. Sharp Edg_ • Remove the other blade in the same manm;r. FIGURE 21. Torque Wrench • Loosen the two hand knobs and cupped washers which secure the chute deflector, and raise the chute deflector. • Insert a 1/2" or 3/4" diameter pipe through the flail screen into the impeller to keep it from turning, or remove the flail screen and insert a piece of wood (2 x 4) into the chute opening. • Remove the two outside screws on the blade, using a 3/16" allen wrench and a 1/2" wrench. • Remove the blade by removing the center bolt, lock washer and flat washer. NOTE: Use caution when removing the blade to avoid contacting the weld bolts on the housing. 14 NOTE: A DIRTY AIR CLEANER WILL CAUSE ENGINE TO RUN ROUGH. BE CERTAIN AIR CLEANER IS CLEAN AND ATTACHED TO THE CARBURETOR BEFORE ADJUSTING CARBURETOR. DO NOT MAKE UNNECESSARY ADJUSTMENTS. FACTORY SETTINGS ARE SATISFACTORY FOR MOST APPLICATIONS AND CONDITIONS. • When sharpening the blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. An unbalanced blade will cause excessive vibration when rotating at high speeds and may cause damage to the unit. Never attempt to change maximum engine speed. It is pre-set at the factory and should be changed only by a qualified service technician who has the necessary equipment. • The blade can be tested for balance by balancing it on a round shaft screwdriver or nail. Remove metal from the heavy side until it is balanced evenly. See figure 22. Nail ! / ° The carburetor may need re-adjusting if engine lacks power or does not idle properly. If adjustments are needed, proceed as follows. • Close idle mixture valve (see figure 24) clockwise ( f'_ ) finger tight only. Forcing may cause damage. Then open 1-1/2 turns counterclockwise ( ,,_ ). • Start engine and allow to warm for five minutes. • Move throttle control lever to IDLE position. • Rotate throttle counterclockwise (,,_) and hold against idle speed adjusting screw. Turn idle speed adjusting screw until engine is running at 1750 RPM. \ Blade FIGURE 22. • When reassembling the blade, tighten to between 550 and 650 inch pounds, or lacking torque wrench, tighten securely. • Turn idle mixture valve clockwise (¢-_) (lean mixture) until engine JUST starts to slow. Then turn it counterclockwise (,,--,) (rich mixture) until engine starts to run unevenly. Set at midpoint between rich and lean mixture. FLAILS The flails, located inside the housing, may be reversed when they become dull. It is suggested that this procedure be performed by your nearest Sears Service Department. • • THROTTLEADJUSTMENT To adjust throttle control lever, loosen or tighten wing nut until throttle control lever moves with some resistance and still remains in desired position when engine is running. See figure 23. Recheck idle RPM and readjust if necessary. Move throttle control lever to FAST position. Engine should accelerate without hesitation or sputtering. If it does not, carburetor should be readjusted, usually to a slightly richer mixture. Throttle Speed Screw Throttle Control. Lever Idle Mixture Valve Wing Nut FIGURE 24. ENGINESPEED Your engine speed has been factory set. Do not attempt to increase engine speed or it may result in personal injury. If you believe the engine is running too fast or too slow, take your chipper-shredder to the nearest SEARS Service Center for repair and adjustment. FIGURE 23. CARBURETORADJUSTMENT WARNING: _IL IF ANY ADJUSTMENTS ARE TIRES ENGINE TO MADE IS THE RUNNING ENGINE (E.G.WHILE CARBURETHE TOR), KEEP CLEAR OF ALL MOVING PARTS. BE CAREFUL OF HEATED SURFACES AND MUFFLER. Recommended operating tire pressure is 24 p.s.i. (sidewall of tire may give tire manufacturer's recommended pressure). Equal tires pressure should be maintained on both rires. When installing a tire to the rim, be certain rim is clean and free of rust. Lubricate both the tire and rim generously. Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. 15 TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE !(S) CORRECTIVE ACTION Engine fails to start • Engine shut-off _,witch OFF. • Fuel shut-off val_'e closed. • Fuel tank empty, or stale fuel. • Spark plug wire disconnected. • Faulty spark plu(.i. Move to ON position. Open fuel shut-off valve. Fill tank with clean, fresh fuel. Connect wire to spark plug. Clean, adjust gap or replace. Loss of power; operation erratic • • • Spark plug wire loose. Unit running on (,HOKE. Blocked fuel line or stale fuel. • Water or dirt in ftlel system. • Carburetor out o adjustment. • Dirty air cleaner. Connect and tighten spark plug wire. Move choke lever to OFF position. Clean fuel line; fill tank with clean fresh gasoline. Disconnect fuel line at carburetor to drain fuel tank. Refill with fresh fuel. Adjust carburetor or contact your SEARS Service Center. Service air cleaner. See Customer Responsibilities section of this manual. Engine overheats • Carburetor not a,Jjusted properly. • Engine oil level I_)w. Contact your SEARS Service Center. Too much vibration • Loose parts or d;tmaged impeller. Stop engine immediately and disconnect spark plug wire. Tighten all bolts and nuts. Make all necessary repairs. If vibration continues, have unit serviced by a SEARS Service Center. Unit does not discharge • Discharge chute clogged. • Foreign object Io :lged in impeller. Stop engine immediately and disconnect spark plug wire. Clean flail screen and inside of blower housing. See Service/Adjustments section of this manual. Stop engine immediately and disconnect spark plug wire. Remove lodged object. • Shredding blade and/or chipper blades dull. Rate of discharge slows considerably or composition of discharged material changes Fill crankcase with proper oil. Sharpen or replace shredding and chipper blades. NOTE: For repairs beyond the minor adjustm_ nts listed above, please contact your nearest SEARS Service Center. HOW TO ORDI-R REPLACEMENT PARTS Your Sears merchandise has added value when you consider that Sears has service units nationwide Each chipper-shredder has its own model number. Each engine has its own model number. staffed with Sears trained technicians...professional technicians specifically trained on Sears products, having the parts, tools and the equipment to insure that we meet our pledge to you..."we service what we sell." The model number for your chipper-shredd_,_r will be found on a label attached to the frame. The model number for the engine will be fou_ld on the blower housing of the engine. All parts listed herein may be ordered throu(jh Sears, Roebuck and Co. Service Centers and mcst Retail Stores. IF YOU NEED REPAIR SERVICE OR PARTS: WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: REPAIR SERVICE 1-800-4-REPAIR (1-800-473-7247) *PRODUCT - "5 H.P. Chipper-Shredder" *MODEL NUMBER - 247.795950 ORDERING PARTS 1-800-FeN-PART (1-800-366-7278) *ENGINE MODEL NO. - 133412-0059-01 *PART NUMBER *PART DESCRIPTION 16 SEARS CRAFTSMAN 5 H.P. CHIPPER-SHREDDER MODEL Repair Parts !9 50 47 17 NO. 247.795950 SEARS CRAFTSMAN 5 H.P. CHIPP ER-SHREDDER MODEL NO. 247.795950 Repair Parts KEY NO. PART NO. 742-0571 710-1254 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 23 24 25 26 27 28 29 3O 31 32 33 34 35 36 37 38 39 736-0217 736-0247 11459B 711-0564 711-0833A 711-0834 715-0249 736-0192 681-0030 781-0490 710-1054 712-0411 736-0119 710-0825 736-0142 750-0793 711-0835 712-0291 714-3010 781-0457 714-0149B 781-0480 712-3010 736-0242 720-0170 747-0744A 732-0542 781-0489 781-0475 736-0170 712-3010 781-0459A 710-0157 736-0119 710-3008 DESCRIPTION KEY NO. Blade Hex Patch Bolt 3/8-2z x 2.25" Lg. (Gr. 8) L-Wash. 3/8" I.D.H.B FI-Wash..406" I.D. x .25" O.D. Hdn. Flail Flail Spacer Clevis Pin.496" Dia. Flail Spacer w/.160"1" ia. Hole Spring Roll Pin 1.12" .g. FI-Wash..531" I.D. x )4" O.D. Impeller Ass'y. Comp I Chipper Blade Flat Hd. Scr. 5/16,24 :.75" Lg. Hex Top L-Nut 5/16-2 (Gr. 5) L-Wash. 5/16" I.D.* Hex Bolt 1/4-20 x 3.7_ Lg.* FI-Wash..281" I.D. x 50" O.D. Chute Hinge Spacer .66" Lg. Clevis Pin .5" Dia. x 4 32" Lg. Hex Ctr. L-Nut 1/4-20 I'hd. Cotter Pin Shredder Screen Internal Cotter Pin 3/_ ' Dia. Chute Deflector Ass'y Hex Nut 5/16-18 Thd. ',Gr. 5) Bell-Wash..345" I.D. .88" Hand Knob Chipper Door Rod Torsion Spring 1.14" g. Chipper Door Chipper Chute Ass'y. Spec. L-Wash. 5/16" D. Hex Nut 5/16-18 Thd. 'Gr. 5) Shredder Frame Hex Bolt 5/16-24x .7,_ Lg. L-Wash. 5/16" I.D.* Hex Bolt 5/t6-18 x .7,_ Lg. (Gr. 5) 40 41 42 43 44 45 46 47 48 710-0380 681-0004 781-0474A 735-0639 133412-0059-01 747-0531A 742-0546 712-0429 710-0601 49 50 51 52 53 54 55 56 11480 736-0264 710-0542 781-0487B 16522B 781-0494 16524B 710-0286 57 58 59 60 61 62 63 712-0107 11461B 726-0214 737-0195 750-O786 738-0813 734-1597 734-1598 734-1455 741-0487 734-0255 737-0280 732-0629 747-0747 781-0492 781-0493 726-0106 764-0199A 723-0400 770-8473H 64 65 66 67 75 76 77 78 79 ---- l-Incl. Ref. 1,6, 7, 8, 9, 10, 11, 12, 13, 14 *Common Hardware--May NOTE" Specifications notice or obligation. Be Purchased Losally. subject to change PART NO. without 18 DESCRIPTION Hex Bolt 5/16-18 x t .75" Lg.* Flail Housing Ass'y.--L.H. Flail Housing Ass'y.--R.H. Spark Plug Boot Engine--B&S 133412-0059-01 Release Bar Torsion Spring 1.06" Lg. Elastic Lock Nut 5/16-18 Thd. Hex Wash. Hd. Self-Tap Scr. 5/16-18 x .75" Lg. Stop Washer FI-Wash. 5/16" I.D. Hex Bolt 5/16-18 x 8.38" Lg. Back-Up Plate Inlet Guide Ass'y. Pivot Hopper Hood Upper Guide Ass'y. Truss Mach. Scr. 1/4-20 x .5" Lg. Hex L-Nut 1/4-20 Thd. Upper Leaf Ramp Section Push Cap 5/8" Dia. Rod Drain Elbow Spacer .64" I.D. x .38" Lg. Shredder Axle Wheel Ass'y. Comp. Tire Only Rim Only Flange Bearing .632" I.D. Air Valve Grease Fitting Torsion Spring Hopper Door Rod Hopper--Pivot Door Hopper Lockout Brkt. Cap Speed Nut 1/4" Rod Bag (Not Shown) Safety Glasses (Not Shown) Owner's Manual BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 133412-0059-01 Repair Parts REF. NO. 1 2 3 5 7 8 9 10 11 t3 PART NO. 495133 399268 *299819 214040 *272157 495774 *27549 94621 66578 94221 13J 14 94167 94679 15 2OO 227 230 305_ 306 307 308 337 383 528 552 562 592 614 615 616 635 869 87O 871 94387 223886 494906 94742 94619 224820 94680 224740 802592 89838 231818 231079 92613 231082 93306 93307 231077 66538 211787 211436 262001 978 979 982 1019 REF. NO. 75 98A 165 201 209 I 222 232 284 346 347 663 984 *271736 494807 94658 495861 614 230 @_.._ 615 DESCRIPTION Cylinder Assembly Bushing--Cylinder Seal--Oil Head--Cylinder Gasket--Cylinder Head Breather--Valve Chamber Gasket--Valve Cover Screw--Breather Mtg. Grommet--Breather Tube Screw--Cylinder Head (2-5/16" Long) Stud--Cylinder Head Screw--Cylinder Head (2-15/32" Long) Plug--Pipe, 1/4" Std., Square Head Guide--Air Lever Ass'y.--Governor Washer--Governor Lever Screw--Hex Hd. Shield--Cylinder Screw--Cylinder Shield Cover--Cylinder Head Plug--Spark Wrench--Spark Plug Tube--Breather Bushing---Governor Crank Bolt--Governor Lever Nut--Hex Cotter--Pin Retainer--E-Ring Crank--Governor Elbow--Spark Plug Seat--Intake Valve Seat--Exhaust Valve (CobaliteO) Guide---Exhaust Valve Note: 63709 Guide--Intake Valve. Gasket--Cover Cover--Oil Gard® Screw--Oil Gard_ Cover Label Kit PART NO. 495659 493280 94692 262865 262283 494899 260585 94620 93705 493521 93343 224746 11 _562 10 305A 200 15 1019 LABEL KIT I *REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR INSTRUCTION MANUAL. 984 DESCRIPTION Washer Kit Screw Ass'y.--Speed Adj. Nut--Wing Link--Governor Spring--Governor Plate--Gov. Control Spring--Link Screw--Hex Hd. Screw--Sem Switch--Rocker Screw--Sem Bracket---Indicator Light _* Included in Gasket Set--Part No. 495661. I Assemblies include all parts shown in frames. 19 J BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 133412-0059-01 Repair Parts REF. NO. PART NO. 12 *270080 16 *270125 *270126 495845 18 19 20 21 22 493916 495660 495307 66768 94682 24 25 222698 393819 393820 393821 393822 399067 399014 399015 399016 26026 298909 298908 299430 390459 26 27 28 29 30 32 33 34 35 36 40 45 46 219 220 284 441 523 524 525 741 842 847 221890 94745 211119 261044 260552 26478 93312 260642 212733 494845 221551 94620 224240 494416 *271485 280578 261696 *270920 494417 DESCRIPTION Gasket--Crankcase (.01fi Thick, Std.) Gasket--Crkcse. (.005" "1"lick) Gasket--Crkcse. (.009" T lick) I Crankshaft Note: To Replace Cranks _aft Gear Pin--Order Part No. 230978. Cover Ass'y.--Crankcase Bushing_rankcase Coy Seal--Oil Plug--Oil Filler Screw--Crankcase Covel Mounting Sem Key--Flywheel Piston Ass'y. (Std.) Piston Ass'y. (.010" O.S.) Piston Ass'y. (.020" O.S.) Piston Ass'y. (.030" O,S.) Ring Set--Piston (Std.) Ring Set--Piston (.010" O.S.) Ring Set--Piston (.020" O.S.) Ring Set--Piston (.030"O,S.) Lock--Piston Pin Pin Ass'y.--Piston (Std.) Pin Ass'y.--Piston (.005" _ ) Rod Ass'y.--Connecting Rod Ass'y.--Connecting (.020" Undersize Crankl: in Bore) Dipper_onn. Rod Screw--Conn. Rod Valve--Exhaust Valve--Intake Spring--!ntake Valve Spring--Exhaust Valve Retainer--Spring Tappet--Valve Gear--Cam Gear--Governor Washer--Thrust Screw--Hex Hd. Bracket_il Fill Dipstick and Cap Ass'y. Seal--Oil Fill Tube--Oil Fill Gear--Timing Seal--Oil Fill Cap Tube Ass'y.--High Oil Fill * Included in Gasket Set--Part 20 220 27 5=3 _84= 52 284 36 _35 o524 40 40 *REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR INSTRUCTION MANUAL. No. 495661. I Assemblies include all parts shown in frames. 2O I BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 133412-0059-01 Repair Parts REF. NO, 51 52 53 95 98 104 108 111 116 118 124 125 127 130 131 133 134 137 141 164 611 634 634A 955 ,., 975 REF. NO. 159 445 535 642 843 966 969 971 PART NO. *272295 *272585 94706 94098 398185 224783 262820 oA *493765 94681 495652 223470 493556 398187 °398188 495651 281247 494451 .A -A 495650 493640 PART NO. 280871 494511 495246 281188 280149 494902 94120 94727 DESCRIPTION Gasket--Carburetor Mtg. Gasket--Intake Port Screw--Adapter Mtg. Screw--Round Head Screw--Idle Adjusting Pin--Hinge (Sold in Kit Only) Valve--Choke Spring--Lever Gasket--Sealing (Sold in Kit Only) Valve and Spring--Needle Screw--Hex Washer Head Carburetor Assembly Plug--Welch Valve---Throttle Shaft and Lever--Throttle Float Assembly--Carburetor Valve--Inlet (Includes Seat) Gasket--Bowl (Sold in Kit Only) Shaft--Choke Manifold--Intake Elbow--Fuel Pipe Seal--Shaft (Sold in Kit Only) Seal--Choke Shaft (Sold in Kit Only) Screw--Fuel Bowl Bowl Assembly--Carburetor 108_ I 111, 130 611 52 164 642 535 DESCRIPTION Support--Filter Filter--Air Cleaner Element--Air Cleaner Cover--Air Cleaner Sleeve--Lever Base--Air Cleaner Screw--Hex Head Screw--Hex Head * Included in Gasket Set--Part No. 495661. * Included in Carburetor Overhaul Kit--Part No. 493762. A Included in Carburetor Gasket Set--Part No. 490937. REF. NO, PART NO. 54 284 300 613 832 864 883 94705 94620 494562 94729 494903 494904 *272309 DESCRIPTION 61 Screw--Hex Head Screw--Hex Hd. Muffler--Exhaust Screw--Sem Guard--Muffler Flange--Muffler Gasket--Exhaust Part No,Spark 494905Arrester (Optional I Muffler Kit Equipment) I Assemblies include all parts shown in frames. 21 I : BRIGGS I AND STRATTON 5 H.P. ENGINE MODEL II NO. 133412-0059-01 Repair Parts 429 REF. NO. PART NO. 182 184 185 187 224709 93559 94010 393815 187A 188 429 601 495218 94357 281190 93053 957 958 972 493988 494539 495345 DESCRIPTION Bracket--Fuel Tank Screw--Hex Hd. Nut--Hex Line-Fuel (11" Long, Cut to Suit) Pipe--Fuel (Molded) Screw--Hex Head Cover--Spark Plug Clamp---Fuel Pipe (Gree_ Note: 93807 Clamp--Fue Pipe (Black) Cap-Fuel Tank Valve Ass'y.--Fuel Shut-( Tank Ass'y.--Fuel * Included in Gasket Set--Part REF. NO. 55 56 57 58 59 60 65 69 69A 456 459 461 515 608 1016 PART NO. 494846 493824 262594 280406 396892 393152 94686 280973 224322 224321 492833 262626 262625 494782 224278 __84184184_ le2_'t_ _ No. 495661. DESCRIP_ON Housing--Rewind Starter Pulley--Rewind Starter Spring--Rewind Starter Rope--Rewind Starter (Cut to Required Length Insert--Starter Handle Handle--Rewind Starter Screw--Starter Mtg. Washer--Rewind Starter Washer--Rewind Starter Retainer--Rewind Starter Pawl---Starter Pin---Starter Spring--Torsion Starter Ass'y.--Rewind Cover--Rewind Starter 57 55 65 Assemblies include all parts shown in frames. 22 I BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 133412-0059-01 Repair Parts REF, NO. PART NO. 23 37 73 304 305 332 333 335 356 297229 222443 224633 494790 94619 92284 397358 93414 495135 356A 495118 363 455 851 19069 494770 221798 73 DESCRIPTION 305 Flywheel--Magneto Guard--Flywheel Screen--Rotating Housing--Blower (Red) Screw--Blower Housing Mounting Nut--Flywheel Armature Group Screw--Armature Mounting Sem Wire Assembly (Armature to Switch) Wire Assembly (Stop Switch to Ground) Puller--Flywheel Hub--Starter Cable Terminal--Ignition 455 23 304 332 335 REF. NO. PART NO. 3 7 9 12 *299819 *272157 *27549 *270080 *270125 *270126 20 51 52 104 116 *495307 *272295 *272585 •A °493765 118 493762 121 127 134 •398188 137 495661 358 *271485 524 •A 634 634A oA 842 883 977 978 *270920 *272309 490937 *271736 DESCRIPTION 363 Seal--Oil Gasket--Cylinder Head Gasket--Valve Cover Gasket--Crankcase (.015" Thick, Standard) Gasket--Crankcase (.005" Thick) Gasket--Crankcase (.009" Thick) Seal--Oil GasketJCarburetor Mtg. Gasket--Intake Port Pin--Hinge (Sold in Kit Only) Gasket--Sealing (Sold in Kit Only) Valve and Spring--Needle Carburetor Overhaul Kit Plug--Welch Valve--Inlet (Includes Seat) Gasket--Bowl (Sold in Kit Only) Gasket Set Seal_il Fill Seal---Shaft (Sold in Kit Only). Seal--Choke Shaft (Sold in Kit Only) Seal-Oil Fill Cap Gasket--Exhaust Gasket Set--Carburetor Gasket--Cover I 358 GASKET 134 137 OVERHAUL _ 634A_ 116 137 @ 634 977 CARBURETOR GASKET SET I Assemblies include all parts shown in frames. 23 116 634A 121 CARBURETOR * Included in Gasket Set--Part No. 495661. • Included in Carburetor Overhaul KitJPart No. 493762. A Included in Carburetor Gasket Set--Part No. 490937. 127 I SET 634 KIT I;;RRFTSMRN® OWNER'S MANUAL 5 HORSEPOWER 3 CUTTING STAGE MIJLCHING AND BAGGING CltlPPER-SHREDDER 247.795950 Ea(:h chipper-shredder has its own model enc ine has its own model number. number. The model number for your chipper-shredder on ;_ label attached to the frame. ThE, model number for the blower housing of the engine. engine will Each will be found be found on the All parts listed herein may be ordered through Sears, Roebuck and Co. Service Centers and most Retail Stores. WHEN ORDERING REPAIR FOI.LOWlNG INFORMATION: HOWTOORDER REPAIRPARTS *P_ ODUCT- PARTS, ALWAYS GIVE THE "5 H.P. Chipper-Shredder" *M()DEL NUMBER *EI_GINE MODEL - 247.795950 NO. - 133412-0059-01 *PART NUMBER *PART DESCRIPTION YOL r Sears merchandise has added value con ;ider that Sears has service units nationwide when you staffed with SezLrs trained technicians...professional technicians specifically trained on Sears products, having the parts, tool3 and the equipment to insure that we meet our pledge to y 3u..."we service what we sell." Par_ obtener un manual de operador Ilanle al 1 800 800-7310 y pida 770.8473H para modelo 247.795950. SEARS, ROEBUCKAND CO., Hoffman Estates, IL en EspaSol, el manual 60179 por favor nt)mero U.S.A.