WangYe WY250T-3 User manual

PREFACE
Thanks for your purchasing the motorcycle WY250T-19, and sincerely welcome you to
be our motorcycle user. To enjoy a more safe and pleasurable driving, at first please
familiarity with the manual must carry on before driving. Your personal safety depends not
only the vigilance and familiar operation skills, but also relates to whether you are familiar
with the mechanical performance. Before driving, check-up and periodical maintenance are
basic requirement. If maintenance and repair needed, go to our service center for help. If you
know the mechanic knowledge and have the tools, the dealer can offer you help with the
maintenance and repair, like providing the parts catalogue and the spare parts.
This manual explains in detail the correct operation and maintenance of WY250T-19,
together with the expectation for your long-time use. Modifications in specification could
cause the discrepancy with some figures and content in the manual, we feel sorry for that
and hold the final right of interpretation.
Have a good enjoyment and thanks again for your purchasing!
THE IMPORTANT POINTS TO ATTENTION
Ÿ The driver and passenger
This motorcycle was only used for one driver. Never exceed to the Max load capacity of the motorcycle.
Ÿ For the safety, never drive to the motorcycle in the atrocious weather or the cold weather(under -12℃)
Ÿ For the road surface:
This kind of motorcycle is only drive in the high road.
• About the caution banner with the safety or environment, stick to the sundries box cover, the rear shelf,
and fuel tank cover. (Look at the clearly in the time for use or before use)
• Please carefully read the user manual
You must pay attention to the sentence or paragraph with caution banner.
Warning
Not following the operation instruction in this manual may cause great damage to you.
Attention:
Not following the operation instruction in this manual may cause injury to both you and vehicle.
Regard this manual as a permanent parts, even when transfer the vehicle to other people, transfer the
manual at the same time
LIST
Ⅰ. Motorcycle safety driving
Rules for safety driving ………………………1
Payload…………………………………………2
Ⅱ.Parts Subassemblies and manual
Parts & subassemblies ……………………3
Meter and indicator …………………………5
Ignition switch …………………………………5
Fuel meter ……………………………………6
Headlamp switch ……………………………6
Starting switch ………………………………6
Engine stop switch …………………………6
Main beam switch …………………………7
Turning signal light switch…………………7
Horn switch …………………………………7
Turning lock…………………………………7
Seat lock ……………………………………8
Front luggage case ………………………8
Ⅲ.Operation guide
Checking before driving……………………9
Engine Starting ……………………………14
Driving motorcycle…………………………15
Driving operation …………………………16
Braking operation ………………………16
Engine power off operation……………………17
Stopping the motorcycle……………………… 17
Ⅳ.Service and maintenance
maintenance periodic schedule ……………18
Simple trouble solution ………………………21
Cleaning air filter ………………………………23
Battery maintenance ……………………………23
Adjusting idling speed …………………………24
Replacing engine oil and cleaning strainer…… 25
Replacing gearbox oil …………………………26
Spark plug…………………………………………27
Replacing fuse ……………………………………27
Radiator maintenance …………………………28
Ⅴ.Vehicle storage………………………………29
Ⅵ.Vehicle identification ………………………30
Ⅶ.Tool set ………………………………………30
Ⅷ. Main Technique Parameter ………………31
IX. Circuit diagram………………………………33
Ⅹ. Emission Control System
Warranty Statement ……………………… 34
Ⅰ. Motorcycle safety driving
Rules for safety driving
1. The motorcycle happen the many accidents, all reasons are that the car drivers didn’t look at the
motorcycle drivers. So the motorcycle drivers must:
l
Put up the coat in bright color
l
Avoid to the driving at night .you must drive on guard and carefully to the strong light.
2. Particular care should be exercised at the level crossing of roads, entrance and exit of parking lot or on
the automobile lane.
3. Don’t speeding, because the speeding usually to happen an accident.
4. You must get to the driving license and familiar with motorcycle. Never lend motorcycle to the man without
driving license or unfamiliar with motorcycle.
5. Avoid driving the road with accidental, easily result the operation failure or the part was broken.
6. Always do a pre-riding inspection before operating the vehicle.(Ref P9)
7. During drive, grasp the handle and feet on the footrest.
1
Payload
l warning:
The light goods can only put in the rear shelf or other deposited place.
The goods payload not heavier than Chart 1:
Chart 1
Deposited
Weight (kg)
Luggage
1
Rear shelf
5
※The motorcycle max payload is 200kg, including the weight with the driver, the passenger and the
goods.
※If the motorcycle is over loading, it can affect the motorcycle stability and operation.
※The goods on the motorcycle must fasten.
2
Ⅱ.Parts Subassemblies and manual
Parts & Subassemblies (Fig1.Fig2)
Fig 1
3
Fig2
Fig 2
Dashed(……)Indicate the not see parts directly
4
Meter and indicator (Fig 3)
⑴ main beam indicator
⑵ engine tachometer
⑶ fuel meter
⑷ RH turning signal light
⑸ odomter
⑹ time
⑺speedometer
(8)time adjustment button
⑼LH turning signal light
Fig 3
Ignition Switch(Fig 4)
⑴ (ON)—when the switch turn to this position, Start engine and do not pull out the key.
⑵(OFF)—when the switch turn to this position, Start engine power off and take out the
key.
⑶(LOCK)—When the switch turns to” LOCK”, Take out the key .do not do any turning
operation. And do not start engine and light.
Notice: If the engine is idling speed for a long time in the hot climate,
It will appear too hot. Phenomenon must close engine.
Fig 4
5
Fuel Meter(Fig 5)
Fuel Meter (5) shows the approx remainder of flue. When
The hand point to (F), it indicates Full tank of 13L.
When the hand at E it indicates the remainder of flue is 2L.
Headlamp Switch (1)(Fig 6)
Headlight switch: three position“ ” 、“
”and“•”
:Headlamp, stopllight, position light and meter light turn on.
:
Fig5
:Position light and meter light turn on.
•:Headlamp, stoplight, position lighted instrument turn off.
Starting Switch ( 2)(Fig 6)
Press this button to start engine.(Ref P14)
Engine stop switch(3)(图 6)
Press“
”button,the engine stop,restart the engine,press
“•”button。
Fig6
6
Main beam switch (1)
(Fig 7)
Press“
”button,is main beam;Press“
”button is dipped beam.
Turning signal light switch (2)(Fig 7)
When the switches on ( ) ,the left turning signal light turn on. When the
switch on ( ), the right turning signal light turn on, Press it down the light
turn off.
Horn Switch ( 3)(Fig 7)
Fig7
Press the horn makes sound.
Steering handle lock(Fig 8, Fig 9)
Turn handle left to end, presses down ignition key1 to(LOCK)
,the steering device are locked. Do the above
opposite it opened.
7
Fig8
Fig9
Seat Lock
Insert the key to seat lock hole under seat, then turn clockwise
direction and pull the pole according to the arrow direction,
may open the seat. (Fig 10, Fig 11)
Insert the key to left side hole of the seat, turn clockwise
Fig10
Fig11
direction, then rotate the handle according to the arrow direction,
图 10
may adjust the height of seat. (Fig 12, Fig 13)。
Rotate the handle according to the arrow direction,
may move the seat position. (Fig 14, Fig 15)
Fig13
Fig12
Front Luggage Case(Fig16)
Use Key turn clockwise 90°for opening
front luggage case 1.
Insert Key and turn clockwise 90°,push the
front
Luggage
case
closely,
then
turn
counterclockwise 90°for closing front luggage case.
Fig16
8
fig14
Fig15
Ⅲ. Operation guide
Checking before driving
For safety and prevent trouble or accident,
Pre-check up is necessary everyday.
Fuel
When the pointer or fuel meter is close to red section, replenish oil;
meanwhile, check the fuel tank and carburetor rack or not.
•
Fuel tank capacity:12 升
•
Turn counter-clock wise to open the tank cover.(fig17)
•
•
Suggestion gasoline: octane number is 90 above.
Do not replenish fuel together with tidy or water.
NOTICE:
Ÿ
The gasoline is inflammable, and can be on fire under certain conditions even exploding.
Therefore, refuel should be on excellent ventilation place, and stop engine firstly. Meanwhile
Smoking and lighting fires strictly prohibited when you refuel and storage.
Ÿ
Refueling, don’t replenish full. You should tighten the fuel tank cover.
Ÿ
If swallow the oil careless, see the doctor at once.
9
Checking engine oil
Checking engine oil level(Fig 18, Fig19)
1、 Take the main stand for stand the vehicle on the ground, wring
out the oil hole cover/ gauge 1, use rag to clean the gauge, and
then insert gauge back. Pull out for checking oil stain.
2、 When the oil mass close the gauge lower limit mark 2, should
add the oil, when the oil lower than upper limit mark 3, then
reinsert the oil hole cover/ gauge, Screw the cover and check it is
FIG 18
petrol dripping.
Suggestion the engine oil:
SAE-15W/40
3
2
FIG19
10
The free path of rear brake handle(Fig20、Fig21)
Measure the free path of rear brake handle before the detent function. The free path should be within
(10~20)mm from the end of brake handle to calculate.
•
Adjust nut:
(A)Increase the free path.
(B)Decrease the free path.
After adjusting,
the axle pin (2) should touch closely with nut (1) groove after adjust.
Fig21
Fig20
11
Abrasion mark of the drum brake(Fig22)
(1)
Reference marks
(2)
Indicate marks.
If totally brake. Change the brake block when reference marks and indicate marks must be situated a
straight line.
Noted:Once the brake needs to replace for a new one, please
go for the nearest maintenance service where there are technicians trained by formal
training to check. Spare parts of our company only can be used for replacement.
1
2
Fig22
12
Tire
Check the tire pressure regularly and adjust.
•
Check when the tire cooled
•
Check if there any metal trash or gravel in the groove of tires, especially,should maintenance when the
tire lack.
•
Inspect whether there is nick, embed nail or other tartness object on the tread or not. Inspect whether
there is impress, dent or distortion for rim or not. If find any damaged, should invite service department to
inspect for you.
•
When the tire pattern wear and tear to the wear sign, must change the new tire.
WARNING:
•
If the tire pressure dose not accord with the standard, it will properly cause the traffic accident. If the
tire pressure is too low, the tire will fetch away or take of rim.
Ÿ
It is dangerous that use the worn tire; it will have effect to friction between tire and rode. Maybe
difficult to drive or accident.
13
Engine starting (Fig 23)
• Preparative before starting:Set up the main stand,put the key into
ignition switch and turn to “ON”,flameout Switch to” ON”.
•
Electric starter:Press start button (1) to start engine.
DO not use the starter more than 5 seconds each time.
NOTICE:
•
Electric starting is only in the condition of grasping the brake
handle.
Fig 23
Electric starting not succeed, if starting again with it, we must stop for 30 seconds, If still can’t start, Please
use kick-start.
Engine kick-start: open ignition switch and add gasoline slowly, step kick-starter pedal down quickly with
strength to start engine.
Notice: After using kick-starter pedal, pull it back to original position. Otherwise have effect to
safety ride, and bad to engine.
Had better not open ignition switch when scooter has not use for a long time, and first step kick starter
for some times. Make flue into carburetor and then into cylinder, and open ignition switch, Start engine, it
is easy to start engine like this.
• If cold start warm up engine for 3 minutes.
14
Driving motor:
WARNING:
Wear the trousers to avoid touching with exhaust pipe and was burnt.
The entire device must be installed according to requirement of the traffic rule.
• Take the license to riding.
NOTICE:
Control the speed and load during 1000km of running in period. Load should be within 150kg (including
driver) If take more weight and speed will reduce life of engine.
Speed as per Chart 2:
Chart 2
Leg(km)
0~200
200~500
500~1000
Speed (km/h)
≤30
≤45
≤55
15
Driving operation
• Take back Main stand and Sit on the seat, Left foot step on the ground make the vehicle and Ground upright.
• Release rear brake level, accelerate slowly with throttle grip, then motorcycle will move forward smoothly.
Decelerate gradually when you stop.
WARNING
• Don’t operate the throttle ON-OFF suddenly, Otherwise, the motorcycle will run out, Maybe lose control.
• Before drive, must take the stand.
Braking operation:
1. Control throttle grip
If want to reduce speed, Must control the throttle grip, at that time use the two-brake system, this point is very
important.
Notice: if the drive will be done in this situation, for example: damp or loosely roads, raining .no matter
brake, accelerate or turn must take care.
2. Operate front and rear brake
Notice: Must totally close the flue when drive in a descent, and use two-brake system for reduce
speed. Don’t uses brake continuously, other wise it will reduce the effect of brake because of too
hot.
Warning: Don’t use single brake when drive with high speed, special crooked and slippery road. Must
use dual-brake system for avoiding accident.
16
Engine power off Operation(Fig 24, Fig 25)
• Turn off Throttle:Revolve to the lowest place according to picture. (Normal situation is loose the throttle grip,
and the engine is idling speed)
• Put the key to “OFF”
Fig24
Fig25
Stopping operation:
When the motorcycle stop, put the key to “LOCK” position .put down stand and lock handle.(Ref P7)
Warning:Motorcycle should be park on the Solidity and Flat ground, otherwise, it maybe make some body injured or
vehicle down .
Alarm points:
•
Locking the handle and do not left key in the lock hole.
•
Put the motor into the garage.
17
Ⅳ.Service and maintenance
Maintenance periodic Schedule
The maintenance is important to motorcycle, If drive with high speed in bad situation for a long time, must add
the times of maintenance, If motorcycle have a big repaired or a accident, Must take it to check for mainly spare
parts. For example: frame, indicator parts and so on. Repair or change the worn parts. Make sure safety.
Notice: Don’t change motorcycle make sure it’s safety, Must use good quality spare parts if
replace spare parts .if use bad quality spare parts, it will influence the safety of motorcycle.
Warning: Must close engine when make maintenance .it make sure the repairer’s safety. And put down
the stand on the smooth ground.
Notice: Must make a good maintenance if the motorcycle don’t use over a month, or don’t use in all the
winter. Make sure fuel, tire and battery avoiding corroding.
18
Periodic Maintenance Chart(Chart 3)
When you will make the Periodic Maintenance, you should inspect before driving.(Ref P9)
I:Inspect and adjust when necessary。
C:Clean
R:Replace
Chart 3
Cycle
1
Item
Every Month
Fuel Pipe
﹡
﹡
﹡
﹡
﹡
Speedometer(×1000km)
4
8
12
6
12
18
I
I
I
I
I
I
C/1000km, if need: R
C/2000km,If need: R
I
I
I
I
I
Throttle operation
Air filter core
(Note 1)
Spark Plug
Idling speed
I
Ref
Page
15
22
26
23
19
Chart 3
Cycle
1
Item
Every month
﹡ Transmission
﹡Gearbox oil
(Note 3)
(300km)R
Brake system
Brake Switch
﹡
﹡
﹡
﹡
﹡
Headlamp
Suspension
Bolts&Nuts tighten
(Note2)
Wheel, Tire
Turning
bearing
Speedometer(×1000km)
4
8
12
6
12
18
Per 1000km I, If need: R
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Ref
Page
25
11
12
*If you have all of tool and maintenance document, you are a mechanic person, or else must let special
person maintenance and repair.
*For safety, we claim all of items have done by mechanic person.
Note: 1.If this area is very damp or have a lot of dirty .you had better make a short time
2. If it was used on accidental road every day, must make maintenance.
3. According to season to change
20
SIMPLE TROUBLE SOLUTION (CHART 4)
Complaint
Symptom and possible causes
Plug not
sparking
Engine
does not
start
Chart 4
Spark plug
is weak
No mixed air in
cylinder
Cylinder
compresses
strength low
Remedy
Damaged spark plug
Damaged Ignition Coil
Defective CDI
Defective ignition switch
Replace
Replace
Replace
Replace
Renegade or loosely Ignition system
Connect well or tighten
Spark plug gap too small or big
Adjust
Replace
Spark plug pole burn
Spark plug accumulates carbons
Clear out
Fuel use out
Replenish
Oil mouth stop up
Dredge
Fuel tank switch wear
Change
Fuel path stop up
Dredge
Air filter stop up
Clean the air filter element
Intake system leak
Check and clear out
Spark plug seat leak
Cylinder cover leak
Tighten spark plug
Change washer
Piston ring & cylinder wear badly
Change piston or cylinder
Chart 4
21
Complaint
The vehicle is
unable to
accelerate
performance
badly
Symptom and possible causes
Change fuel
Oil path stop up
Clean oil path
Ignition time is too early or too late
Check coil and change CDI
Spark too weak or flameout
Check ignition and clear out
Mixed air too dense or race
Clean& adjust carburetor
Engine leak
Check and clear out
Muffler stop up
Dredge
Belt wear
Replace
Replace
Replace
Replace
Automatic clutch roller wearing
Electric
start failure
Driving
unsteady
Brake Failure
Remedy
Octane value of the fuel is too low
Clutch worn
Starting relay worn
Turning bearing gap too wide
Charge
Adjust
Lack of tire pressure
Pump
Front& rear Axle flexible
Tighten nut
Replace
Replace
Replace
Electric quantity lack
Brake pad fray to limit
Brake cam fray
Brake cable damaged
Free path overlong
Adjust
22
Cleaning Air Filter(Fig 26)
• Take apart the bolt of air filter cover.
• Take out filter element.
• Compress air or use dry brush to clean filter element.
• Do the above opposite to reinstall the air filter.
NOTICE:
• Do not use gasoline or low burning point solvent to clean paper
filter element.
Fig26
Battery maintenance(Fig 27)
It is adopted the airtight battery (don’t add water)
Notice: Do not take apart the airtight
• If the motorcycle have not been used for a long time.
Taking off
the battery and putting it into a dry and place。
• The head of battery was corroded, please take it off and clean.
(Can use boiled water)
NOTICE: turn off the ignition switch, take apart negative pole ○- first,
+ when you are installing.
but install positive pole ○
Fig 27
23
Adjusting Idling speed(Fig28、Fig29)
The carburetor is in the best situation before sale, if the carburetor is still
influence riding. Please adjust it under the instruction of professional man.
•
•
Warm up few minutes before start
Adjust idle screw (1) to improve idle speed slightly to enter to
fasten, withdraw it than screw slowly after stocking to fasten to
mix and then rapidly, to stabilizing the position at most, then
withdraw slowly, get and stabilize the position the lowest.
•
Fig28
After adjust idle, then adjust accelerograph handle to free path for
2-4mm,then use adjustor (2) to adjust, screw down nuts, and then screw
up it after adjust.
• Adjusting the idle speed, it should be able to suddenly strengthen the throttle, the
rotational speed of the engine should be excessively steady, no temper and
flameout, stop working or arrange organ not to flameout at being last throttle.
Fig29
24
Replacing engine oil and cleaning strainer
Replacing engine oil(Fig30)
Suggestion engine oil: SAE 10W/40
• Change the engine oil before engine cold, and under the condition of steady
of motor.
Cleaning strainer
• Take out oil hole cover and oil filter (1) then take strainer (2) and spring
(3).
• Using liquor clean the strainer.
• Install oil filter then take strainer and spring.
• Replenish the standard engine oil to upper limit line of the oil hole cover.
• Install the cover of hole and liter.
•
Start engine and keep for few minute then flameout..
•
Measure the lever of engine oil again, makes sure it is not leak.
25
Fig30
Replacing gearbox oil(Fig 31, Fig32)
Suggestion gear oil: SAE 80W/90
Oil container
replacing capacity:0.18L
•
Make the motorcycle on the stand
•
Take apart the immiting bolt (1), and the spilling bolt (2)
Fig31
NOTICE: The engine must be warmer when spilling and the
vehicle must be steady by main stand. Make sure the Engine
is empty
•
Reinstall the spilling bolt after clean. and screw up.
•
Inject 180ml to engine through immit bolt
•
Install immit bolt and screw up.
Fig32
26
SPARK PLUG(FIG 33)
Specification of Spark Plug
Standard:DPR7EA(NGK)、D7RTC OR DPR6EA
• Disconnect the spark plug cap, and then use the special handle to remove Spark plug。
• Check if the spark plug electrodes and the center porcelain head burned accumulative carbon, etc.
If the spark plug is burned out, replace new spark plug.
• Adjust the spark plug gap between(0.6~0.7)mm .
1
• Don’t use an unspecified spark plug.
(0.6~0.7)mm
2
Fuse replacing
The specified electric current of the total fuse is 15 A, which is in Battery.
If the connection is not good, the fuse will overheat and breakdown.
Do not use brass wires to replace the recommended.
Fig33
27
Radiator Maintenance
Suggestion Cooled liquid Type: anti-freeze liquid
It’s only using antirust antifreeze liquid for this engine.
Inspecting
Take the Right Cover of Footrest, check the liquid lever should be1/5, ifless
than 1/5, please immit it.
Immiting the cooled liquid
Ÿ
Clockwise open the cover 1of radiator, if the cooled liquid is not full,
please keep it full, and then cover it.
Ÿ
if you want to add more cooled liquid, starter the engine liquid rising
Fig34
80℃,waiting for 5minuts then open the cover 1,till the liquid full,
close the cover.
Ÿ
As per above order, you can add the 3rd liquid.
Ÿ
You can open the cover 2 to immit the liquid after the engine is
cooled also.
Warning:
When the engine is high temperature, do not open the cover, in
case the liquid burst out to injury somebody..
28
Fig35
Ⅴ.Vehicle storage
Storage
For store up the motorcycle for a long period of time, for example, in wintertime, some steps should be taken to
prevent malfunction of and damage to its components, which might be caused by long storage. Besides, before the
long storage, proper maintenance has to be carried out for fear that it might be forgotten when vehicle is put back into
use after storage.
1. Change engine oil.
2. Drain off fuel from the fuel tank and carburetor.
Warning: Gasoline is inflammable and may cause fire and even explosion under certain conditions. Therefore,
do not smoke, make fire or have any fire left behind on draining off fuel.
•
Take out the spark plug, pour about 15~20ml clean engine oil into the cylinder, step down the kick lever
repetitively for several times so as to have machine oil distributed all over the engine and finally fit the
spark back on.
•
Remove battery,batter can’t be kept on icing and direct sunshine location,charge every month.
•
Wash the motor, wipe it dry and apply an even coat of wax to the painted surface. Antirust can
prevent the surfaces from rusting.
Put the vehicle in a shady and cool place far from humidity and direct sunshine and cover it
properly (but not with plastic or other painted materials)。
•
Reuse motorcycle.
Take down the motorcycle cover and clean the motorcycle, if the storage time exceeds 4 months, Must change
engine oil.
Must charging if need, and then install battery.
Must check all of terms before drive (Page9) for the safety must try the motorcycle with lower speed for some
time in a not busy rode.
29
Ⅵ、Vehicle Identification
Position of the vehicle type, VIN and engine number.(FIG 36)
Provide the above frame and engine Number when register, get the license, yearly
inspection, and also enjoy the after-service clause.
The nameplate is riveted on the fixing board of the right part of main stand(See
page 3)
Fig36
Ⅶ.Tool set
Tool bag(Fig 34)in the boot of seat, Using for the urgent accident when driving, it including the something of the
following:
8×10mm spanner 12×14mm spanner Screw drive
Hexagon spanner Wrench bar
18.5×17mm wrench spanner
FIG37
30
Ⅷ.MAIN TECHNIQUE PARAMETER
CHART 5
Item
L×W×H mm
Wheelbase mm
Ground Clearance mm
Dry weight kg
Max Load kg
Turning Angle of Steering
Handle
V=60km/h
Parameter
1480
Item
Front tyre
Rear tyre
135
Air Pressure, Fr tyre
170
Air Pressure, Rr tyre
200 kPa
250 kPa
150
Transimission system
CVT
≤48º
Gear ratio
5.12~15.05
2100×795×1130
Parameter
130/60-13
130/60-13
Front brake distance
Fr brake average deceleration
Rear brake distance
Rr brake average deceleration
≤37.3m
≥4.4(5.8) m/s2
≤54m
≥2.9(5.8) m/s2
169MM,single Cylinder
4 stroke, water-cooled
69×66.8
Brake Distance m
≤7(30km/h)
Engine Type
Max Speed km/h
Consumption L/100km
≥85
Bore×stroke mm
Displacement ml
≤3.1
249.8
31
Chart 5
Item
Climb ability
º
Parameter
≥18
Lean
-1.3%
Starting system
Lubricate System
Rated Power
Max Torque
Compression ratio
Spark Plug Model
Spark plug gap mm
mm
Valve Clearance mm
Electric
Press & splash
10.5kW/ 6500(r/min)
17.6N.m/ 5000 (r/min)
10:1
Idling speed
Item
Clutch
Fuel tank
Battery
Fuse
Headlight
Parameter
Automatically centrifugal
L
13
12V 9Ah
License light
Turning light
Fuel
15 A
12V35W/35W×2
12V 21W/5W
12V 5W
12V 10W
RQ90 Above
Ignition System
CDI
(1500±150)r/min
Gearbox oil
SAE 80W/90
Capacity of engine oil
1.1L
Capacity
Gearbox oil
Engine oil
SAE 10W/40
r/min
Taillight/Brake light
DPR7EA(NGK)、D7RTC OR DPR6EA
0.6~0.7
0.1 (cold)
32
of
0.18L
IX. Circuit diagram
33
Ⅹ. Emission Control System Warranty Statement
Wangye USA Co., LLC is pleased to explain the emission control system warranty on
Highway Motorcycle. New Highway Motorcycle must be designed, built and equipped to
regulations and standards of the United States Environmental Protection Agency and the
California Air Resource Board and free from defects in material and workmanship that may
keep it from these requirements in the all applicable regulations.
Wangye USA Co., LLC must warrant the emission control system on the highway motorcycle
for 5 years or 18,000 km, whichever comes first, provided that there has been no abuse, neglect
or improper maintenance of highway motorcycle.
1. Period of Warranty
The period of warranty shall be one year on delivery, during this period of warranty:
(i). Any part defective by reason of the manufacturer’s faulty workmanship or material will be
replaced or repaired free of charge;
(ii). Any repairs or adjustments made necessary by reason of the manufacturer’s faulty
workmanship or material will be performed free of charge.
Emission control system may include parts such as the carburetor or fuel injection system, the
ignition system, catalytic converter and engine computer, if it is equipped. Also included may
be hoses, belts, connectors and other emission-related assemblies.
2. Responsibilities of Customer
To obtain repairs under warranty, the customer must:
34
(i). Ensure that the motorcycle is properly operated, maintained and stored as specified in the
Owner’s Manual;
(ii). Give notice to dealer approved by Wangye USA Co., LLC or other qualified service facility
of any and all apparent defects immediately upon discovery, and make the entire
motorcycle available at the time for inspection and repair at the dealer’s place of business;
(iii). Provide proof of warranty coverage to dealer;
(iv). Authorize the dealer to tear down the motorcycle for diagnostic evaluation should it be
required.
All warranty repairs must be done by the dealer and final approval of any repairs rests with
Wangye USA Co., LLC. All parts replaced become the property of Wangye USA Co., LLC.
3. Exclusion
This warranty does not cover the repair or damage resulting from abuse or neglect of the
motorcycle. Examples of abuse and neglect include, but are not limited to:
(i). Racing and competition;
(ii). Use of lubricants, oils and fuel/oil mixture other than those recommender in the Owner’s
Manual, improperly installed accessories and use of parts or accessories that are not
equivalent in design and quality to genuine Wangye parts;
(iii). Damage as a result of accidents, collisions, contact with foreign materials, impact,
submersion or use of the motorcycle after discovery of a defect;
(iv). Appearance-related damages of body parts. Examples of such damages include but are not
limited to: scratches, dents, fading, flaking and peeling;
(v). Motorcycle which has been modified in any way from the standard specifications shown in
the Owner’s Manual, for example, the odometer has been altered;
(vi). Normal wear and tear, corrosion and routine maintenance, such as the recommended
service inspections;
35
(vii). Pre-delivery inspection and assembly;
(viii). Damage from theft, fire, vandalism, explosion, water or acts of God.
4. Restriction
This warranty is in addition to, and not a modification of, any legal warranty required by the
laws of any state of US.
Subject to any applicable sales or consumer legislation, the above warranty is in lieu of any
warranty or representation, express or implied, including any warranty of performance,
merchantability or fitness for a particular purpose on the part of Wangye USA, and any other
obligation or liability on behalf of Wangye USA, and the above warranty constitutes your sole
remedy and the full liability of Wangye USA. In no event shall Wangye USA be liable for
special, incidental or consequential damages howsoever caused, whether by negligence or
otherwise resulting directly or indirectly from the use of the Motorcycle, or the Motorcycle’s
having replacement parts or the unavailability of replacement parts. Wangye USA does not
assume or authorize any person to create or assume for Wangye USA any obligation or liability
in connection with the Motorcycle or any part thereof distributed by Wangye USA.
5. Contact
For any questions regarding emission control system warranty, please contact as following:
Company Name: Wangye USA Co., LLC
Address: 1170 Corporate Dr. West Ste. 204, Arlington, TX 76006
Tel: 817-640-1108 ext 219
Fax: 817-649-5006
36