Audiovox MMD10 - DVD Player With LCD Monitor Installation guide

MMD11
11" OVERHEAD LCD
MONITOR WITH
DVD PLAYER
OPERATION
MANUAL
128-8290
Important Notice
Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags. Do not route
wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or D pillars of the vehicle. Routing wires in these areas or
running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants. If you have
any questions regarding wire routing in a vehicle, please contact Audiovox Technical Support at 1-800-225-6074.
When connecting power and ground in a mobile video installation ensure that the ACC wire is fused at the point where it is connected to the vehicle ACC wiring.
Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product.
An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information,
system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or
video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle's parking brake is applied.
An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not
applied must be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.
Licensed under one or more of the following patents,
Patent NOS. 5,775,762 and 5,927,784
Warnings
u
u
u
u
u
u
u
Do not use any solvents or cleaning materials when cleaning the video monitor.
Do not use any abrasive cleaners, they may scratch the screen.
Use only a lightly dampened lint free cloth to wipe the screen if it is dirty.
Lock the LCD screen in the fully closed position when not in use.
Before putting on headphones always adjust the volume setting to the lowest position.
Remember to leave the dome light switch in the off or auto positions when the vehicle is unattended, as the dome lights, if left
on, can drain the vehicle’s battery.
Do not put pressure on the screen.
FEATURES
Congratulations
Congratulations on your purchase of the Jensen MMD11
DVD Player with Drop-Down Video / Monitor. The MMD11
has been designed to give you and your family many years of
video entertainment in the mobile environment. Please read
the directions that follow to familiarize yourself with the
product to ensure that you obtain the best results from your
equipment.
Please note: Installation options vary, see the individual
owner’s manuals for each component in your system to
obtain a full understanding of each component’s operation.
•
•
•
•
•
•
•
•
•
•
•
•
Safety Precaution
For safety reasons, when changing video media it is
recommended that the vehicle is not in motion, and that you
do not allow children to unfasten seat-belts to change video
media or make any adjustments to the system. System
adjustments can be accomplished using the remote control,
while seat-belts remain fastened. Enjoy your Audiovox
entertainment system but remember the safety of all
passengers remains the number one priority.
3
11" TFT (Thin Film Transistor) Active Matrix LCD
(Liquid Crystal Display) Monitor
Built-in DVD Player
Multi-Lingual OSD (On Screen Display) for Control of
Picture Quality and Functions
Infrared Transmitter for use with IR Wireless
Headphones
Three Audio / Video Source Inputs (DVD, AUX,AV1)
Dome Lights with Built-in Three Way Switch
Built-in 16 Channel Frequency Wireless FM Modulator
Last Position Memory for DVD
Screen Mode Selection (16:9, 4:3)
Full Function Remote Control
Backlit Controls
AV Output
CONTROLS AND INDICATORS DIAGRAM (FRONT VIEW)
8 7 6 5 43 2
1
1. EJECT () Button
This Button is used for ejecting discs from the disc
compartment when the source is DVD and the unit is
powered up.
9
10
2. STOP (n) Button
This button is used to stop playback.
11
3. Source Select
Use to select one of the three sources: DVD, AUX,AV1.
12
4. Picture Select (+)
To increase the level of selected picture controls.
13
5. Picture Select Button
Allows the user to enter the picture adjustment mode.
14
6. Picture Select (–)
To decrease the level of selected picture controls.
7. FMM Source Select Switch
Used to select the frequency in sequence rotation: FM OFF,
CH1 88.1MHz, CH2 88.3MHz, CH3 88.5MHz, CH4 88.7MHz,
CH5 88.9MHz, CH6 89.1MHz, CH7 89.3MHz, CH8 89.5MHz,
CH9 89.7MHz, CH10 89.9MHz, CH11 90.1MHz,
CH12 90.3MHz, CH13 90.5MHz, CH14 90.7MHz,
CH15 90.9MHz, CH16 91.1Mhz.
15
8. PLAY (u) Button
This button is used to start playback of a disc.
16
4
CONTROL FUNCTION DESCRIPTION (FRONT VIEW)
CONTROL FUNCTION DESCRIPTION
(SIDE VIEW & BACK VIEW)
9. POWER ( ) Button
Used to turn the system on/off.
Side View
1
10. Dome Lights
Provide additional interior illumination.
11. Infrared Transmitter and Sensor
Transmits audio to optional wireless headphones. Also allows
the remote control to operate the MMD11 and to control other
accessories in the system.
1. DVD Disc insertion Slot
For loading and removing discs. Unit must be in a powered on
state to load disc when disc is inserted. Insert disc with label
side facing up.
12. Three Position Dome Light Switch
ON – Turns on the dome lights.
OFF – The dome lights will not turn on in this position.
AUTO – Automatically switches on the dome lights in
conjunction with the vehicle's interior illumination.
13. Ventilation Openings
14. LCD Cut Off Switch
Used to turn off the LCD panel monitor when in the closed
position.
Back View
15. LCD Panel
16. Screen Release
Press to release the screen.
1 2 3
1. Auxiliary Video Input
2. Auxiliary Audio Left Input
3. Auxiliary Audio Right Input
5
REMOTE CONTROL OPERATION
MAIN FUNCTION DESCRIPTION
1
2
3
4
5
POWER
MONITOR SELECT
EJECT
35
M1
M2
TV
DVD
1
2
3
4
5
6
7
8
SOURCE
AUTO
MEMORY
6
34
SKIP/
SEARCH
7
ERASE/
WRITE
8
9
10
11
12
13
0
CHANNEL
FMM
ON/OFF SELECT
DAY/
NIGHT
PIX
RETURN DISPLAY
IRT
ON/OFF
MUTE
15
33
32
31
30
29
OK
14
Battery Installation
9
VOLUME
MENU
SETUP
28
16
Before attempting to operate your Remote Control, install the
batteries as described below.
1) Turn the Remote Control face down. Using your finger, slide
the battery cover off in the direction of the arrow.
2) Install Two “AAA” batteries. Make sure that proper polarity
(+ or -) is observed.
3) Align the cover tabs with the remote control and slide the
cover until it locks.
The remote control will operate the MMD11. It is not a universal
remote control and will not control equipment from other
manufacturers.
17
18
19
20
21
22
23
6
AUDIO
SUBTITLE
REPEAT
ZOOM
A-B
27
26
25
24
* Function control is available on the unit and the remote control.
** Function not available in this model.
1. POWER Button*
Press this button to turn the unit ON and OFF.
2. MONITOR SELECT
M1 Button – Sets the remote control code to allow control of the unit set to M1 mode only.
M2 Button – Invalid function for this model
3. TV Mode Select Button**
Switches certain function keys on the remote control for TV functions.
4. DVD Mode Select Button
Switches certain function keys on the remote control for DVD functions.
5. SOURCE Button*
Each time the button is pressed, the audio / video source will change in the following sequence: DVD > AUX > AV1.
6. AUTO MEMORY Button (AUTO PROGRAM Button)**
When the AUTO MEMORY button is pressed, all channels are searched and channels that are detected with signals of sufficient levels are
automatically stored in memory.
7. SKIP / SEARCH Button**
This button selects between SKIP and SEARCH mode. In "SKIP mode" the TV tuner will tune and stop on channels that are programmed
into memory when the CHANNEL UP / DOWN buttons are used. When the SKIP mode is disable, the TV will stop on all active channels.
8. ERASE / WRITE Button**
While tuned to a channel, pressing this button will alternately store or erase the channel from memory.
7
9. FMM ON / OFF Button*
Turns the wireless FM Modulator on or off.
10. CHANNEL SELECT Button*
Selects the wireless FM Modulator Frequency (CH1 88.1MHz, CH2 88.3MHz, CH3 88.5MHz, CH4 88.7MHz, CH5 88.9MHz, CH6 89.1MHz,
CH7 89.3MHz, CH8 89.5MHz, CH9 89.7MHz, CH10 89.9MHz, CH11 90.1MHz, CH12 90.3MHz, CH13 90.5MHz, CH14 90.7MHz,
CH15 90.9MHz, CH16 91.1MHz)
11. RETURN Button
Press Return Once : Go to disc menu.
Press Return Twice : Go to movies playback.
12. DISPLAY
Press to display current disc information while the disc is playing. Press cursor (pq) buttons to select the Title or Chapter.
For Title/Chapter selection use the numeric buttons to enter the desired Title Chapter selection.
13. CURSOR / CHANNEL UP DOWN (pqtu) **
Use these buttons to navigate the menu selections on the screen.
Use the CHp to increase the channel number and use CHq to decrease the channel number. **
14. OK Button (ENTER)
Used to implement a selected setting or menu option.
15. MENU Button
Allows the user to access the DVD menu (DVD MODE).
16. REPEAT Button
Allows the user to repeat a selected title, chapter, or track.
8
17. AUDIO Button
Press to display and select the available AUDIO languages in DVD mode. Each time you press the button, the language changes.
Note: The languages for audio vary from disc to disc.
18. SUBTITLE Button
Press to display and select the available subtitle language in DVD mode. Each time you press the button, the subtitle language changes.
Note: The type and number of languages for subtitle vary from disc to disc.
19. STOP (<) Button*
Press to stop playback.
20. PREVIOUS (9) Button
Press to return to the previous chapter or track.
21. SCAN BACKWARD (7) Button
Press to search in a backward direction. Press repeatedly to change the search speed from 2, 4, 8, and 16 times the normal speed.
22. PAUSE (II) Button
Allows the user to pause the playback. Pressing pause again or pressing the Play Button will resume normal playback.
23. PLAY Button*
Press to activate the play mode when a disc is loaded in the disc compartment.
24. SCAN FORWARD (8) Button
Press to search in a forward direction. Press repeatedly to change the search speed from 2, 4, 8, and 16 times the normal speed.
25. NEXT (:) Button
Press to skip to the next chapter or track.
9
26. A-B Button
Allows user to repeat the playback from point A to point B.
Press A-B button On-Screen DisplayDVD player
Repeat AMark the beginning of the section to repeat (Set point A)
Once
Repeat AB Mark the end of the section to repeat (Set point B)
Twice
Cancel the A-B repeat function
3 times AB Off
27. ZOOM Button
Press this button to enlarge the picture when playing a DVD disc.
Press ZOOM button
DVD player perform
Enlarge the picture 1 times of the original size
Once
Enlarge the picture 2 times of the original size
Twice
Enlarge the picture 3 times of the original size
3 times
Picture is returned to original size
4 times
28. SETUP Button
Press to display the Setup Menu which allows the user to change the DVD player options such as TV DISPLAY, OSD LANGUAGE,
PARENTAL CONTROL etc. Refer to the settings and Adjustments section for more information.
29. IRT ON/OFF Button
Turns the Infrared Transmitter IRT ON or OFF for IR Wireless Headphones. Pressing M1 then IRT ON/OFF will control the IR
Transmitter for M1.
30. MUTE Button
Press this button to mute all the audio.
Pressing the button again restores the sound to the previously set level.
10
31. DAY / NIGHT Mode Button**
This control toggles the unit between “Day” and “Night” LCD illumination modes. In the “Day” mode, the LCD backlit intensity is at
maximum. In “Night” mode, the LCD backlit is dimmed to a preset level that is more suitable for low light operation.
32. PIX Button (Picture Select)*
Each time this button is pressed, the on screen picture adjustment displays the “adjustment bar” for BRIGHTNESS, CONTRAST,
COLOR, TINT or RESET. Once the desired adjustment bar is displayed, use the VOLUME(+)/ VOLUME(–) button to adjust the setting.
The display will automatically turn off if no adjustments are made within 6 seconds, or is any other button is pressed.
33. VOLUME DOWN (–) or UP (+)*
Press to decrease or increase the level of the picture adjustments.
34. NUMBER Buttons
Allow the user to enter numbers 0 to 9 for selection of selection of CD tracks, DVD chapters and password.
35. EJECT () Button*
This button is used to eject the disc.
11
MENU ADJUSTMENT
The System Menu Contains features and options that let you customize your system to change the screen mode display, OSD language
and source default.
1) Press the SYSTEM MENU button on the remote, the main page of the system menu will appear on screen.
2) Use the cursor buttons p or q to select the desired item in the main page and press the OK button to select.
3) The sub menu will appear on screen.
4) Use the cursor buttons p or q to select an item in the sub menu and then press the OK button to select.
5) Press the Menu button to exit System Menu.
Note: System Menu can be controlled via Remote Control only. (Items selected in the menu will have a green background)
SCREEN MODE SELECT
This allows the user to change the screen format (aspect ratio 16:9, 4:3).
1) To select the screen aspect ratio format highlight SCREEN MODE and then press the OK button to enter the sub menu. Then use the
cursor buttons por q to select from either 4:3 or 16:9. Press the OK button to confirm the setting.
SYSTEM MENU
SCREEN MODE
OSD LANGUAGE
SOURCE DEFAULT DVD
SCREEN MODE
4:3
16:9
12
OSD LANGUAGE
This allows the user to select the language for the on-screen display. The user can either select English, Spanish, French or German for the
OSD language.
SYSTEM MENU
SCREEN MODE
OSD LANGUAGE
SOURCE DEFAULT DVD
OSD LANGUAGE
ENGLISH
SPANISH
FRENCH
GERMAN
SOURCE DEFAULT DVD
This allows the user to select from:
DVD default on- Whenever the unit is turned on it will return to DVD mode.
DVD default off- Whenever the unit is turned on it will return to the last source selected.
SYSTEM MENU
SCREEN MODE
OSD LANGUAGE
SOURCE DEFAULT DVD
SOURCE DEFAULT DVD
ON
OFF
13
SETTINGS AND ADJUSTMENTS
The Setup Menu contains features and options that let you customize your DVD player. For example, you can set a language for the onscreen display or prevent DVD playback for children.
Using the Setup Menu
1. Press the SETUP button on the remote. The Setup Menu appears on the screen as shown per diagram.
Language
Video
Language Setup
Language
OSD Language
: English
Video Setup
Video
Subtitle
: Off
Rating
Audio
: English
Rating
Rating Setup
Misc
Misc Setup
Misc
2. In order to set the desired option, move the highlight into the setup area using the cursor button u.
3. After entering the setup area, highlight the desired option using the cursor button p or q.
4. Press u to move the highlight to the different options for the selected item. Press p or q to select the desired options, and then press
ENTER to confirm the selection.
5. Repeat steps 3~4 to continue setting the options that reside on the same Setup Page.
6. To change to another Setup page, press t until the highlight moves back to the icon on the top part of the Setup Menu.
Then, repeat steps 2~5.
Exiting the Setup Menu
Press the SETUP button again only.
14
LANGUAGE SETUP
Language
OSD Language
Video
Subtitle
Language for On-Screen Display
Rating
Audio
OSD MENU: The OSD MENU setup allows you to select the language for the on-screen display.
The user can either select English, French, Spanish, German or Italian for the OSD language.
Misc
SUBTITLE SETUP
English
French
Spanish
German
Italian
Language
OSD Language
Video
Subtitle
Rating
Audio
English
French
select "SUBTITLE" using pq button, then press u button to enter the Submenu. Select the subtitle you
desire using pq button, then press "ENTER" to confirm the setting. Press t button to return.
Spanish
German
Italian
Japanese
Misc
Chinese
Note: The subtitle selection is only available for discs that are recorded in the above listed languages. If the selected,
language is not available, the player will play and display on the screen the original language contained in the disc.
AUDIO SETUP
Thai
Off
Language
OSD Language
Video
Subtitle
Rating
Audio
English
select "AUDIO" using pq button, then press u button to enter the Submenu. Select the audio you
desire using pq button, then press "ENTER" to confirm the setting. Press t button to return.
Spanish
Japanese
Note: The audio selection is only available for discs that are recorded in the above listed languages. If the selected,
language is not available, the player will play and display on the screen the original language contained in the disc.
The TV DISPLAY setup allows you to adjust screen setting (aspect ratio).
4:3 This displays the wide picture with black bands on the upper and lower portions of the screen.
16:9 This displays a wide picture with black bands on the upper and lower portion of the screen.
The bandwidth will vary, depending on the aspect ratio of the disc.
15
German
Italian
Misc
VIDEO SETUP
TV Display
French
Chinese
Thai
Language
TV display
Video
TV type
Rating
Misc
4:3
16:9
TV Type
The TV TYPE setup allows you to select the system to fit to the color system of the TV to be connected.
NTSC - Select this type for NTSC TV
PAL - Select this type for PAL TV
Multi - Select this type for multi-system TV
RATING SETUP
Rating
This item allows you to limit the content of movie playback from G to Adult. The lower the value, the more strict the control.
G
Language Parental
: 6.Adult
PG
PG – 13
Password
Video
R
Rating
NC – 17
Misc
Adult
The rating level can only be changed when the displayed lock is open. For first time use, key in the
default password (3308) and press Enter. To set a new password, key in a new four-digit password and
press enter.
Language
Video
Parental
: 6.Adult
Password
Enter Password
Rating
Misc
Note: The Default Password is 3308. This password is always effective even after you have selected your own password and changed it. To avoid the possibility
of others using the default password to set the parental level and change the password, you can record this default password in another area and delete it from
this manual. Some discs can be limited depending on the age of users while some discs cannot.
Misc SETUP
Language
select "MISC” using pq button, then press u button to enter the Misc menu. Select the subtitle you
desire using pq button, then press "ENTER" to confirm the setting. Press t button to return.
Video
Rating
Misc
16
Load Factory
Screen Saver
: On
Language
Load Factory
Load Factory allows you to reset all options to factory settings.
* This function will not affect the Rating control settings.
Load Factory
Load Factory
Video
Screen Saver
Yes
No
Rating
Misc
Screen Saver
ON -Screen saver will appear
OFF -Screen saver will not appear
Language
Video
Note: The DVD player will enable the Screen Saver mode if the unit is inactive for approximately 3 minutes.
Rating
Load Factory
Screen Saver
Off
On
Misc
Playing DVDs
1. Press the DISPLAY button on the remote control to display the status banner. The banner includes title, chapter, angle, audio, subtitle,
title selection & chapter selection.
2. Title Selection
Press numeric (0~9) buttons to initiate a change of title selection. Then press ENTER to implement the selection.
3. Chapter selection
Press numeric (0~9) buttons to initiate a change of chapter selection. Then press ENTER to implement the selection.
As you toggle through the options, the repeat option changes at that time. The track, for example, repeats once that track has ended. The
selected repeat option loops repeatedly until you turn it off.
17
Playing MP3 Discs
MP3 is a format for storing digital audio. An audio CD-quality song can be compressed into the MP3 format with very little loss of quality,
while taking up much less space. CD-R discs that have been encoded in MP3 format can be played on your DVD player. The DVD player
plays the songs in the order they were burned on to the disc.
When playback is started the elapsed time of the track that is playing will be displayed.
00:00:01
Selecting Folders and Songs
03/13
When a device containing MP3 files is loaded in the player, the navigation menu appears automatically.
1. Press p or q to move the highlight to the desired folder (if present) on the left side of the menu and
press OK. The songs in the folder will be displayed on the screen.
2. Press p or q to move the highlight to the desired track containing the song and press OK to begin
track playback.
/TRACK02.MP3
TRACK01
Repeat
Mode
TRACK02
: All
: Shuffle
Edit Mode
TRACK03
TRACK04
TRACK05
Music Playing
TRACK06
:1
Album: genre
Comment:-
Skipping Songs
Use the Next (:) button on the remote control to move to the next song. Use the Previous (9) button to move to the previous song.
Selecting a Play Mode
Filter (For MP3 & JPEG only)
Filter Mode enables or disables the display of files contained on the media based on their file extension.
The Filter function applies to the following formats:
Audio - Audio data format (MP3, WMA)
Photo - Photo data format (JPEG)
Video - Video data format (AV1, MPEG , )
00:00:21
1/12
/
TRACK01
TRACK02
Filter
Audio
Flat Mode
Photo
Video
Repeat :
off
TRACK03
TRACK04
TRACK05
TRACK06
18
Music Playing
Flat Mode: play the entire disc
1/12
This mode is always on (default). During the Flat Mode all the data folders with MP3, JPEG & movies will be
played in sequence. If the Flat Mode function is off, it will only play the selected folder; other folders are disabled.
/
TRACK01
TRACK02
Flat Mode
Repeat :
Off
Mode
Normal
:
TRACK03
TRACK04
TRACK05
Music Playing
TRACK06
Repeat: play repetitively
1/12
Repeat function has 4 options: Off, Single, Folder, All. Move cursor to Repeat function and press OK;
Off/Single/Folder/All are displayed in that order. Repeat default is Off;
/
TRACK01
TRACK02
Flat Mode
Repeat :
Off
Mode
Normal
:
TRACK03
TRACK04
TRACK05
Off
Single
Folder
All
Music Playing
TRACK06
Turn off repeat function
Repeat the song being played until STOP is pressed.
Play all songs in a folder repetitively
Play all songs on the disc repetitively
Mode: play mode
The Mode function has 4 options: Normal, Shuffle, Random and Music Intro. Move cursor to the desired Mode function and press OK;
Normal/Shuffle/Random/Music Intro are selected in that order. The Mode function default status is Normal.
Normal: Play all songs in folder once
Shuffle: Play songs in a folder in a shuffled order. Each song in the folder is played only once.
Random: Play songs in a folder in a random order. Each song in the folder is played only once.
Music Intro: Play each song in order in the folder for 10 seconds
Remark-- The purpose of the Music Intro function is to provide the user with a sample of each song for 10 seconds, thereby making it easy
to select and listen to a favorite song.
15
19
Edit Mode
Program View
Add to Program
1/12
/
TRACK01
Notice: Edit Mode/Program View/Add to program functions are all related and can not be implemented
during play mode or any other program function.
Edit Mode
TRACK02
Program View
TRACK03
Add to Program
TRACK04
TRACK05
Music Playing
TRACK06
Album:------------
Method: Make sure disc playback is off. Move cursor to Edit Mode function and press OK. After Edit Mode is selected, open the folder and
select the songs which will be compiled. A check mark appears to the left of the selected song; highlight the Add to program function and press
OK. The selected song is added to a new program and the check mark disappears; move cursor to Program view function and press OK to
browse the songs in the program.
In Edit Mode, if Add to program function is used, highlight Program view function and press ENTER; the following selections appear:
Edit Mode
Browser View
Clear Program
1/12
/
TRACK01
Method: When Add to program function is finished, highlight the Browser view function; the songs in the new
program are displayed. To delete a selected song, highlight the selected song; a check mark appears to the
left of the selected song. Highlight Clear program function and press OK; the song will be deleted.
20
Edit Mode
TRACK02
Browser View
TRACK03
Clear Program
TRACK04
TRACK05
TRACK06
Artist:
Music Playing
DVD Basics
To get the optimum use out of the DVD section, make sure you read this section completely.
Regional Coding
Both the DVD player and DVDs are coded by region. These regional codes must match in order for the disc to play. If the codes don’t
match, the disc won’t play. This unit’s code is region 1. Other regional codes cannot be played in this unit. The unit will display
“WRONG REGION”.
Types of Discs your DVD will play
•DVD* disc - DVD discs which contain video.
•Audio discs - Audio CDs contain musical or sound content only.
•MP3 discs - A disc that contains audio files (for example, a CD-R with downloaded MP3 files).
* This system is capable of playing most recordable DVD formats. However, due to the variety of disc manufacturers and software, playback
cannot be guaranteed.
Loading and Playing Discs
Before you load a disc, make sure that it is compatible with the player. Insert the disc with the label facing the driver.
Note: the following Discs CANNOT be used with this player :
•MiniDisc
•Laserdisc
•CD-1, CD-ROM, DVD-ROM, Super Audio CD (SACD), DVD Audio, JPEG (KODAK)
To load and Play a Disc
Press the Power button to turn the unit ON. Select DVD mode and insert the disc (Label towards driver) into the disc compartment.
21
TURNING THE UNIT ON OR OFF
1. Pushing in the Screen Release button will unlock the LCD screen and it will drop down slightly. Pivot the screen downward until a
comfortable viewing angle is reached. The hinge friction will hold the screen in position while the system is in use.
2. Pressing the power button* on the unit or the remote control will turn the system on and off. When in use the internal backlighting
will illuminate the controls.
3. After the unit has been turned on and is displaying a picture, adjust the viewing angle, by pivoting the screen to optimize the picture
quality.
4. Remember to turn the unit off and pivot the LCD to the locked position when not in use.
Power
ON/OFF
Button
Remote Sensor
Infrared Transmitter
Screen Release
OVERHEAD DOME LIGHTS
The Dome Lights integrated into the MMD11 are controlled by a three position slide switch. Sliding the switch to the ON position will turn
the lights ON. The OFF position will prevent the lights from turning ON with the vehicle’s interior lighting, and the auto position will allow the
lights to turn ON and OFF with the vehicle’s interior lighting. Refer to the Installation Guide for wire connections. Do not leave the vehicle
unattended with the dome light switch in the ON position, as this could result in a discharged battery.
REMOTE SENSOR
The MMD11 infrared remote sensors to relay signals to the unit when the remote control is pointed at the remote sensor.
22
ACCESSORIES
WIRELESS HEADPHONES
The MMD11 includes a built-in infrared transmitter for use with wireless headphones (purchased separately). The headphone volume is
adjusted using the controls on each headset. Any number of wireless headphones may be used but they must be used within a line of sight
from the transmitter, as infrared transmissions, like visible light travel only in a straight line. See the documentation accompanying your
wireless headphones.
SOURCE FEATURE
AV1
The AV input may be connected to a Video Cassette Player (VCP), video game system, or other audio/video devices. To access the
A/V inputs, turn the MMD11 on and press the source button on the MMD11 or the Source button on the remote control until "AV1" is
displayed on the screen. Turn the audio/video source component on with its power button or remote control. The MMD11 is now ready to play
the audio and video signals from the source connected to AV1 input (use accessory cable part number 11236820 required).
AUX
The MMD11 will accept an audio / video input through the 3 RCA jacks located on the rear of the unit. The audio / video device could be a
video game system, video camera, or other input device.
Video Out
The MMD11 provides a video output for optional audio/video monitor(s). This output will provide an audio/video signal that duplicates the
signal displayed by the MMD11 to an additional monitor or video display. Please see your installer for more information.
23
TROUBLESHOOTING
SOLUTION
PROBLEM
IR remote inoperative
— Verify that the batteries in the remote are fresh.
— Verify that the remote sensor eye is not obstructed.
Disc won't play
— Insert a disc with the label side facing up.
— Check the type of disc you put into disc tray. This DVD only plays DVDs, audio CDs
and MP3s.
— Both the unit and the disc are coded by region. If the regional codes don’t match,
the disc can’t be played. This DVD player is set to Region Number 1.
Play starts, but then stops immediately
— The disc is dirty. Clean it.
— Condensation has formed. Allow player to dry out.
No sound or distorted sound
— Make sure your DVD is connected properly. Make sure all cables are securely
inserted into the appropriate jacks.
— If you are using the 2-channel IR headphones, make sure you turn on the IR
headphone power, make sure the correct channel (A-B) is selected.
— Make sure the Modulator is ON and the proper Frequency has been selected.
— Make sure that unit is set to M1 when using Single Channel Headphones.
Can’t advance through a movie
— You can’t advance through the opening credits and warning information that
appears at the beginning of movies because the disc is programmed to prohibit that
action.
24
SOLUTION
PROBLEM
Not allowed at the moment
— The feature or action cannot be completed at this time because:
1. The disc’s software restricts it.
2. The disc’s software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number that is out of range.
Picture is distorted
— The disc might be damaged. Try another disc.
— It is normal for some distortion to appear during forward or reverse scan.
No forward or reverse scan
— Some discs have sections that prohibit rapid scanning or title and chapter skip.
— If you try to skip through the warning information and credits at the beginning of a
movie, you won’t be able to. This part of the movie is often programmed to prohibit
skipping through it.
25
REPLACEMENT PARTS
Remote Control
SPECIFICATIONS
136-4196
LCD Backlighting
Edge Light Tube
Resolution
800 x RGB x 480
Pixels
1, 152, 000
Operation Temperature
32 ~131º F (0 ~ 55º C)
Storage Temperature
-4 ~ 158º F (-20 ~ 70º C)
Backlit life
15,000 Hours
Video Display System
NTSC / PAL
Video Output
1.0Vp-p @ 75 ohms
Power Source
12V DC
Dimension
LxWxH
14.0” x 12.0” x 2.0”
356mm x 305mm x 60mm
Specifications subject to change without notice.
26
12 MONTH LIMITED WARRANTY
Applies to Movies To Go Mobile Video Products
AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part
thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original
purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair
labor. A game controller, if supplied, is similarly warranted for ninety (90) days.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill
of sale), specification of defect(s), transportation prepaid, to the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred
for installation, removal or reinstallation of the product, or to damage to digital memory/media devices, gaming devices, discs, speakers,
accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through
alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD
OF 24 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. No person or representative is authorized to assume
for the Company any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage
so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788 l 1-800-645-4994
27
128-6429F
© 2007 Audiovox Electronics Corp., Hauppauge, NY 11788
128-8291