Samsung STD24B Specifications

GABD-000099
Ed. 00
OfficeServ 100
General Description Guide
10. 2004.
COPYRIGHT
This guide is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright.
No information contained herein may be copied, translated, transcribed or duplicated for any commercial
purposes or disclosed to third parties in any form without the prior written consent of SAMSUNG Electronics
Co., Ltd.
TRADEMARKS
is the trademark of SAMSUNG Electronics Co., Ltd.
Product names mentioned in this document may be trademarks and/or registered trademarks of their
respective companies.
This guide should be read before the installation and operation, and the operator should correctly install and
operate the product by using this guide.
This guide may be changed for the system improvement, standardization and other technical reasons without prior
notice.
For further information on the updated guide or have a question for the content of guide, contact the address or
homepage below.
Address: Document Center 2nd Floor IT Center. Dong-Suwon P.O. Box 105, 416, Maetan-3dong Yeongtong-gu,
Suwon-si, Gyeonggi-do, Korea 442-600
Homepage: http://www.samsungdocs.com
©2004 SAMSUNG Electronics Co., Ltd.
All rights reserved.
OfficeServ 100 General Description Guide
INTRODUCTION
Purpose
OfficeServ 100, Enterprise IP Solutions System, is a digital telephone system designed for
small to medium-sized businesses
This guide provides an overview of the Samsung OfficeServ 100 including system
structure, hardware, features, facilities and specifications.
Document Content and Organization
This guide is composed of 4 Chapters and 1 Annex. Each chapter is introduced as follows:
CHAPTER 1. Introduction to System
This chapter describes the introduction to OfficeServ 100 system such as general
description, size, configuration, technology, and programming.
CHAPTER 2. Hardware Descriptions
This chapter describes hardware descriptions of OfficeServ 100 such as key service unit,
interface cards, and station equipment.
CHAPTER 3. Specifications
This chapter describes the technical data for the OfficeServ 100 hybrid/key telephone
system such as electrical specifications key service unit, interface cards, station equipment.
CHAPTER 4. Business Feature Package
This chapter describes various features of the OfficeServ 100 system.
ANNEX A. Abbreviation
Acronyms frequently used in this guide are described.
© SAMSUNG Electronics Co., Ltd.
I
INTRODUCTION
Conventions
The following special paragraphs are used in this document to point out information that
must be read. This information may be set-off from the surrounding text, but is always
preceded by a bold title in capital letters.
NOTE
Indicates additional information as a reference.
Reference
OfficeServ 100 Service Manual
Introduces circuit configuration of each section in OfficeServ 100 system, main functions,
parts list, troubleshooting, and disassembly diagram of main device.
OfficeServ 100 Programming Manual
Introduces programming method for the OfficeServ 100 system users. Users can configure
the system using the MMC(Man Machine Communication) program at the digital
telephone. This manual describes how to use the MMC program.
OfficeServ 100 Installation Manual
Introduces the installation related information for OfficeServ 100 system.
Revision History
II
EDITION
DATE OF ISSUE
REMARKS
00
10. 2004.
First Edition
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide
TABLE OF CONTENTS
INTRODUCTION
I
Purpose ...........................................................................................................................................I
Document Content and Organization...............................................................................................I
Conventions ....................................................................................................................................II
Reference .......................................................................................................................................II
Revision History ..............................................................................................................................II
CHAPTER 1. Introduction To System
1-1
1.1
General Description .................................................................................................................. 1-1
1.2
Size and Configuration ............................................................................................................. 1-3
1.3
Technology ................................................................................................................................ 1-8
1.3.1 Switching.......................................................................................................................... 1-8
1.3.2 Memory ............................................................................................................................ 1-8
1.3.3 Microprocessors............................................................................................................... 1-8
1.4
Programming............................................................................................................................. 1-9
CHAPTER 2. Hardware Descriptions
2.1
2-1
Key Service Unit........................................................................................................................ 2-2
2.1.1 Ring Generator Unit RGU1 or RGU2 .............................................................................. 2-3
2.1.2 MISC Card ....................................................................................................................... 2-3
2.2
Expansion Cabinet .................................................................................................................... 2-5
2.3
Interface Cards .......................................................................................................................... 2-5
2.4
Station Equipment..................................................................................................................... 2-8
2.4.1 iDCS Series Equipment ................................................................................................... 2-8
2.4.2 DCS Series Equipment ...................................................................................................2-15
CHAPTER 3. Specifications
3.1
3-1
Electrical Specifications ........................................................................................................... 3-1
3.1.1 Dimensions and Weights.................................................................................................. 3-1
3.1.2 Environments ................................................................................................................... 3-2
© SAMSUNG Electronics Co., Ltd.
III
TABLE OF CONTENTS
3.1.3 Cable Requirements ......................................................................................................... 3-2
3.1.4 System Tones ...................................................................................................................3-2
3.1.5 Keyset LEDs ..................................................................................................................... 3-3
CHAPTER 4. Business Feature Package
4.1
4-1
System Features ........................................................................................................................ 4-2
4.1.1 System Feature Descriptions............................................................................................ 4-3
4.2
Station Features....................................................................................................................... 4-31
4.2.1 Station Feature Descriptions........................................................................................... 4-32
4.3
Display Features ...................................................................................................................... 4-40
4.3.1 Display Feature Descriptions ..........................................................................................4-40
4.3.2 Sample Displays ............................................................................................................. 4-45
4.3.3 Sample Caller ID Displays .............................................................................................. 4-46
4.3.4 Sample UCD Displays .................................................................................................... 4-47
4.4
Sample SMDR Printout (Without Caller ID)............................................................................ 4-48
4.5
Sample SMDR Printout (With Caller ID) ................................................................................. 4-49
4.6
Sample UCD Report................................................................................................................. 4-50
4.7
UCD Call Statistics................................................................................................................... 4-51
4.7.1 Calls in Queue Now ........................................................................................................ 4-51
4.7.2 Abandoned Calls ............................................................................................................4-51
4.7.3 Average Ring Time .........................................................................................................4-51
4.7.4 Number of Times All Agents Busy................................................................................... 4-51
4.7.5 Average Time in Queue .................................................................................................. 4-51
4.7.6 Total Calls Received ....................................................................................................... 4-52
4.7.7 Longest Queue Time Today ............................................................................................ 4-52
4.7.8 Longest Queue Time Now .............................................................................................. 4-52
4.8
UCD Agent Statistics ............................................................................................................... 4-53
4.8.1 Logged In........................................................................................................................ 4-53
4.8.2 Status.............................................................................................................................. 4-53
4.8.3 Calls Answered ............................................................................................................... 4-53
4.8.4 Average Call Time ..........................................................................................................4-53
4.8.5 Average Ring Time .........................................................................................................4-53
4.9
Sample Traffic Report.............................................................................................................. 4-54
4.10 Traffic Report Overview........................................................................................................... 4-55
4.10.1 Beginning & Ending ........................................................................................................ 4-55
4.10.2 Activity ............................................................................................................................ 4-55
4.10.3 Incoming Trunk Calls-Answered ..................................................................................... 4-55
4.10.4 Incoming Trunk Calls-Not Answered............................................................................... 4-55
IV
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.10.5
Outgoing Trunk Calls ...................................................................................................4-55
4.10.6
A Selected Trunk Was Busy.........................................................................................4-56
4.10.7
Intercom Calls Completed............................................................................................4-56
4.10.8
Intercom Calls Not Completed .....................................................................................4-56
4.10.9
Trunk Recalls to Station ...............................................................................................4-56
4.10.10 Trunk Recalls to Operator Group .................................................................................4-56
4.10.11 Internal Page Used ......................................................................................................4-56
4.10.12 External Page Used.....................................................................................................4-56
4.10.13 All Page Used ..............................................................................................................4-56
4.10.14 Group...........................................................................................................................4-57
4.10.15 Outgoing ......................................................................................................................4-57
4.10.16 Busy.............................................................................................................................4-57
4.10.17 Trunk............................................................................................................................4-57
4.10.18 Trunk Name .................................................................................................................4-57
4.10.19 ATTA ............................................................................................................................4-57
4.10.20 ANSD...........................................................................................................................4-57
4.10.21 Not-ANSD ....................................................................................................................4-58
4.10.22 Outgoing ......................................................................................................................4-58
4.10.23 Busy.............................................................................................................................4-58
4.10.24 Outside Calls ...............................................................................................................4-58
4.10.25 Group...........................................................................................................................4-58
4.10.26 ANSD (Answered) .......................................................................................................4-58
4.10.27 Not-ANSD ....................................................................................................................4-58
4.10.28 Intercom.......................................................................................................................4-58
4.10.29 ANSD...........................................................................................................................4-59
4.10.30 Outside Calls ...............................................................................................................4-59
4.10.31 EXT..............................................................................................................................4-59
4.10.32 Station Name ...............................................................................................................4-59
4.10.33 ATTA ............................................................................................................................4-59
4.10.34 ANSD...........................................................................................................................4-59
4.10.35 Not-ANSD ....................................................................................................................4-59
4.10.36 Dialed ..........................................................................................................................4-60
4.10.37 ICM-TRSF....................................................................................................................4-60
4.10.38 TRK-TRK .....................................................................................................................4-60
4.10.39 Pickup ..........................................................................................................................4-60
4.10.40 Intercom.......................................................................................................................4-60
4.10.41 ANSD...........................................................................................................................4-60
4.10.42 Dialed ..........................................................................................................................4-60
4.11 Sample Alarm Report...............................................................................................................4-61
4.12 DECT Service............................................................................................................................4-62
© SAMSUNG Electronics Co., Ltd.
V
TABLE OF CONTENTS
ANNEX A. ABBREVIATION
A-1
A ~ D .......................................................................................................................................... A-1
E ~ M .......................................................................................................................................... A-2
O ~ T .......................................................................................................................................... A-3
U ~ W ......................................................................................................................................... A-4
LIST OF FIGURES
Figure 1.1 OfficeServ 100 General System Diagram ................................................................1-2
Figure 1.2 OfficeServ 100 Configuration Matrix Table (with Analogue Trunks)-Expansion A type ...1-5
Figure 1.3 OfficeServ 100 Configuration Matrix Table (with Digital Trunks)-Expansion A type ..1-5
Figure 1.4 OfficeServ 100 Configuration Matrix Table (with Analogue Trunks)-Expansion B type...1-6
Figure 1.5 OfficeServ 100 Configuration Matrix Table (with Digital Trunks)-Expansion B type..1-6
Figure 1.6 OfficeServ 100 System Configuration (Basic KSU + Expansion A)..........................1-7
Figure 1.7 OfficeServ 100 System Configuration (Basic KSU + Expansion B)..........................1-7
Figure 2.1
OfficeServ 100 KSU .................................................................................................2-2
Figure 2.2
28 Button iDCS Keyset ............................................................................................2-8
Figure 2.3
18 Button iDCS phone .............................................................................................2-9
Figure 2.4
8 Button iDCS Keyset ..............................................................................................2-9
Figure 2.5
64 Button iDCS AOM .............................................................................................2-10
Figure 2.6
14 Button iDCS AOM .............................................................................................2-10
Figure 2.7
DS-5012L............................................................................................................... 2-11
Figure 2.8
DS-5014D .............................................................................................................. 2-11
Figure 2.9
DS-5021D ..............................................................................................................2-12
Figure 2.10
ITP-5012L ............................................................................................................2-13
Figure 2.11 ITP-5014D............................................................................................................2-13
Figure 2.12
ITP-5021D ...........................................................................................................2-13
Figure 2.13
DS-5064B ............................................................................................................2-14
Figure 2.14
WBS24.................................................................................................................2-14
Figure 2.15
WIP-5000M ..........................................................................................................2-15
Figure 2.16 LCD 24B Euro Keyset..........................................................................................2-15
Figure 2.17
STD 24B Keyset ..................................................................................................2-16
Figure 2.18
STD 12B Keyset ..................................................................................................2-16
Figure 2.19 6B LCD Model Keyset..........................................................................................2-17
Figure 2.20
48 Button AOM.....................................................................................................2-17
Figure 2.21A DS 24S Keyset ..................................................................................................2-18
Figure 2.21B
VI
DS 24D Keyset ..................................................................................................2-19
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
Figure 2.22 Economic Keyset................................................................................................. 2-20
Figure 2.23
Door Phone Interface Module ............................................................................. 2-20
Figure 2.24
Door Phone ......................................................................................................... 2-20
Figure 2.25 Single Line Telephone ......................................................................................... 2-21
LIST OF TABLES
Table 3.1 Electrical Specifications ............................................................................................ 3-1
Table 3.2 Dimensions and Weights .......................................................................................... 3-1
Table 3.3 Environments ............................................................................................................ 3-2
Table 3.4 Cable Requirements ................................................................................................. 3-2
Table 3.5 System Tones ........................................................................................................... 3-2
Table 3.6 Keyset LEDs ............................................................................................................. 3-3
© SAMSUNG Electronics Co., Ltd.
VII
TABLE OF CONTENTS
This page is intentionally left blank.
VIII
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide
CHAPTER 1. Introduction To System
This chapter describes the introduction to OfficeServ 100 system as follows.
General Description
Size and Configuration
Technology
Programming
1.1 General Description
OfficeServ 100(Enterprise IP Solutions System), DCS(Digital Communication System), is
a digital telephone system designed for small to medium-sized businesses. It can operate
with the functionality of a square key system, PABX or a combination of both(hybrid).
OfficeServ 100 employs the very latest DSP(Digital Signal Processor) technology.
OfficeServ 100 offers a variety of interface cards that allow connection to the public
telephone network or private networks. These are generally referred to as trunk cards.
Two types of telephones can be connected to the systems. Proprietary digital phones called
‘Keysets’ are connected to DLI(Digital Line Interface) cards. Standard telephone sets
generally called ‘single line telephones’ are connected to SLI(Single Line Interface) cards.
In addition, DLI station ports are used to connect peripheral devices such as door phones
and add-on modules. Miscellaneous circuits are provided to allow such optional features as
external paging, music on hold, background music, common audible devices, alarms and
emergency power failure telephones.
All DCS keysets utilize a single PCB with surface-mounted components assuring the
highest product quality and long life. Samsung’s customary large, easy-to-read displays and
LEDs in the button design make them much easier to use. In many instances, sophisticated
features are made simple through the use of friendly display prompts or push-on/push-off
feature keys.
© SAMSUNG Electronics Co., Ltd.
1-1
CHAPTER 1. Introduction To System
iDCS 28B phone
iDCS 8B phone
Economic phone
iDCS 18B phone
iDCS 14B AOM
6B LCD Model phone
iDCS 64B AOM
Single Line Telephone
12B Large LCD phone
12B 2Line LCD
21B 2Line LCD phone
14B 2Line LCD phone
12B Large LCD IP phone
21B 2Line LCD IP phone
14B 2Line LCD IP phone
LCD 24B phone
48 Button AOM
64B AOM
48VDC Battery
Backup
Computer
Telephone Lines
Loop-Start Trunk
VoIP
Wireless
ISDN PR/BRI
110/220V AC
SMDR
SVMi-4/8
integrated
voice mail & auto
attendant
Printer or call accounting system
Loud Bells
External music sources
Door phones
Voice mail/auto
attendant systems
WBS-24
Figure 1.1 OfficeServ 100 General System Diagram
1-2
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
1.2 Size and Configuration
The OfficeServ 100 system consists of the basic KSU(Key Service Unit), an Expansion
cabinet, Interface cards and Digital keysets. The KSU begins with eight keyset ports
expandable to 18 analogue C.O. line ports, or 24 lines if 4 BRI cards are used, or 32
stations. In addition, up to 8 keyset daughter boards may be added to the system along with
the optional 2 SLI card.
The Expansion cabinet A type has three Universal slots and one DCS slot for TEPRI(PRI)
or SVMi-8, which provides the maximum configuration of 66 ports with analogue trunk
lines or 96 ports with Digital trunk lines.
The Expansion cabinet B type has two Universal slots and two DCS slot for TEPRI(PRI) or
SVMi-8, which provides the maximum configuration of 58 ports with analogue trunk lines
or 88 ports with Digital trunk lines.
Two types of telephones can be connected to the system: proprietary digital stations called
‘keysets’ that connect to DLI ports and standard telephone sets, generally called ‘Single
Line Telephones’, that connect to SLI ports.
The system also has an optional MISC card, which provides Music on Hold facilities, two
serial I/O ports and other useful facilities.
The following charts(Figures 1.2, 1.3, 1.4, 1.5) describe configurations using the basic
KSU, an Expansion cabinet and expansion cards. However, by using the DCS’s unique
KDB(Keyset Daughter Board), which are installed in the base of a digital keyset, the
capacity of the system can be increased by one station per KDB. Installing a KDB-DLI
adds another digital port while a KDB-SLI adds a single line port. Mix and match these
two types of KDB to get up to a total of 8 KDB in the system. Using this method allows the
OfficeServ 100 to expand to a maximum of 64 stations. Adding the optional 2 SLI card to
the KSU provides a further two SLI ports.
The combination of the basic 008 KSU plus three expansion cards in the KSU plus three
expansion cards and one DCS card in the Expansion cabinet plus 8 KDB plus a 2 SLI card
provides a maximum configuration of 96 ports plus Miscellaneous card.
© SAMSUNG Electronics Co., Ltd.
1-3
CHAPTER 1. Introduction To System
Installation environment
- Only one 2 SLI card can be installed in the system.
- Only one MISC card can be installed in the system.
- ISDN cards(BRI, PRI and TEPRI) require a PLL card installed in the KSU.
- Expansion A type consists of three universal expansion slots and one DCS card
slot for TEPRI(PRI) or SVMi-8.
- Expansion B type consists of two universal expansion slots and two DCS card
slot for TEPRI(PRI) and SVMi-8.
- Only 8 KDB can be installed in the keysets connected to the 008 Basic KSU
- OfficeServ 100 system can have up to 48 stations if SVMi-8(or MGI3) is not used.
- OfficeServ 100 system can have up to 40 stations if SVMi-8(or MGI3) is used.
- SVMi-8 or MGI3 card power consume 8 stations
- 4WLI MAX power consume 16 stations(an WBS-24 AP power consume 4 stations)
- Large LCD Keyset(DS-5012L) power consume be three times as much stations.
1-4
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
Trunk Lines
36
Two Cabinets
30
24
18
12
KSU
6
0
8
16
18
26
34
42
50
58
66
Station Lines
Figure 1.2 OfficeServ 100 Configuration Matrix Table (with Analogue Trunks)-Expansion A type
Trunk Lines
78
48
40
Two Cabinets
32
24
16
KSU
8
0
8
16
18
26
34
42
50
58
66
Station Lines
Figure 1.3 OfficeServ 100 Configuration Matrix Table (with Digital Trunks)-Expansion A type
© SAMSUNG Electronics Co., Ltd.
1-5
CHAPTER 1. Introduction To System
Trunk Lines
30
Two Cabinets
24
18
12
KSU
6
0
8
16
18
26
34
42
50
58
Station Lines
Figure 1.4 OfficeServ 100 Configuration Matrix Table (with Analogue Trunks)-Expansion B type
Trunk Lines
70
40
Two Cabinets
32
24
16
KSU
8
0
8
16
18
26
34
42
50
58
Station Lines
Figure 1.5 OfficeServ 100 Configuration Matrix Table (with Digital Trunks)-Expansion B type
1-6
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
The Figure 1.6 describes OfficeServ 100 system configuration using the Basic KSU and
Expansion A type cabinet.
The Figure 1.7 describes OfficeServ 100 system configuration using the Basic KSU and
Expansion B type cabinet.
Figure 1.6 OfficeServ 100 System Configuration (Basic KSU + Expansion A)
Figure 1.7 OfficeServ 100 System Configuration (Basic KSU + Expansion B)
© SAMSUNG Electronics Co., Ltd.
1-7
CHAPTER 1. Introduction To System
1.3 Technology
1.3.1 Switching
System switching is accomplished by means of a custom IC ‘engine’ that provides 256
switchable digital channels. The engine is controlled by its own 16-bit Motorola MC
68000 microprocessor and switching control program. Each of the 256 digital channels is
automatically assigned to carry voice or data as required by system operation in a PCM
format.
In addition to the 256 channels mentioned above, the systems also utilize DSP. Each DSP
may be configured by the switching control program as a DTMF sender, a DTMF receiver
or as a C.O. tone detector on a per-call basis. Each engine chip contains 4 DSP channels.
Four additional DSP are added when a MISC card is installed. This means that the system
contains a total of 8 DSP channels when fully expanded. The DSP channels are fully shared
throughout the system as a common resource.
1.3.2 Memory
The systems operate using stored program control. This program is stored in EPROM chips
or flash memory. All specific customer data is stored in RAM(Random Access Memory)
which is protected against the loss of AC power to the system by an on-board battery
backup system.
The OfficeServ 100 program is stored on a 16 Mbytes NAND flash memory on the Main
Control Processor(MCP1) card. The system boots from a 512 Kbytes boot ROM and
downloads the operating program into 32 megabytes of SDRAM on the MCP1 card.
The customer database is stored in 1 Mbytes of non-volatile SRAM.
1.3.3 Microprocessors
OfficeServ 100 uses distributed processing. The primary processor of the system is a 16-bit
Motorola MC68000 operating at a clock speed of 16 MHz. Secondary processing is in
the some special cards like as BRI and also done in the keysets. The digital keyset uses a
Hitachi H8 processor for data communication within the OfficeServ 100.
The OfficeServ 100 uses distributed processing. Its primary processor is a 32 bit Motorola
MPC855 operating at a clock speed of 50 MHz on the MCP1 card.
These secondary processor are MC68EC000 processor(008 Base Board) running at 16
MHz and provide local control of cards.
1-8
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
1.4 Programming
The OfficeServ 100 system arrives from the factory with default data.
Connect it to trunks, stations and power. Turn the system on and it is fully operational.
The only thing left to do is customize the data to fit the customer’s needs. This is called
programming the system.
MMC stands for Man Machine Communication and each program is assigned a different
three digit code(e.g., 100). These MMC codes are used to view, create or change customer
data. Programming is simply deciding what needs to be done and knowing which MMC is
used to do it. For example: use MMC 601 to designate a station group; enter system speed
dial numbers in MMC 705.
The OfficeServ 100 is a self-configuring system. This means that immediately after
applying power, the OfficeServ 100 reads the types and locations of all installed interface
cards and phones and assigns default data to them. This data provides for system operation
within a few minutes after applying power. This numbering LAN is flexible and may be
changed to suit customer requirements. The installing technician customizes this default
data to meet the end user’s requirements.
The system can be programmed from any LCD display phone without interrupting system
operation. There are three levels of programming: technician, customer and station.
The technician level has access to all programs and can allow the customer access to
system programs as needed. Technician and customer access levels are controlled by a
different security passcodes and access procedure.
The OfficeServ 100 also allows the use of a proprietary computer program called DPAPPCMMC. This permits a technician to program the system using a personal computer.
DPAP-PCMMC can be used on-site to modify the customer database or to download(save)
the entire customer database to a file. This file can then be saved as a backup and be
uploaded when required to restore the database.
Through the use of modems, DPAP-PCMMC can access the OfficeServ 100 system
remotely(off-site) to make database changes or perform uploads or downloads of the
customer database as if the technician were on-site.
© SAMSUNG Electronics Co., Ltd.
1-9
CHAPTER 1. Introduction To System
This page is intentionally left blank.
1-10
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide
CHAPTER 2. Hardware Descriptions
This chapter describes the hardware of the OfficeServ 100 system as follows.
KSU
Interface Cards
Station Equipment
© SAMSUNG Electronics Co., Ltd.
2-1
CHAPTER 2. Hardware Descriptions
2.1 Key Service Unit
The OfficeServ 100 KSU is a single metal cabinet containing the following:
Mounting
Hole
Mounting
Hole
Figure 2.1 OfficeServ 100 KSU
A power supply
Processing and switching
Eight 2B+D digital keyset interfaces
Memory Card
− MEM3: A removable MEM3 card, containing 3 Mbyte Program memory, 1 Mbyte
Data memory with a back-up super capacitor, real time clock, a monitor LED and a
RAM clear switch
− MEM4: A removable MEM4 card, containing 3 Mbyte Program memory, 1 Mbyte
Data memory(only 512 Kbyte is back-up), 512 Kbyte common memory, real time
clock, a monitor LED, a RAM clear switch, and LAN interface
− MCP1: A removable MCP1 card, containing 16 Mbyte NAND Flash memory,
0.5 MByte Boot Flash memory, 32 MByte SDRAM memory, 2 Mbyte SRAM
Data memory(with SP Program and Data memory), 2 Kbyte DPRAM for IPC
communication MP & SP Processor, real time clock, a monitor & LAN status LED,
a RAM clear switch, and LAN interface
2-2
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
2 Champ connectors for external connections and other connectors for the Expansion
cabinet and the Ring Generator Unit
One Internal Music source or an External Music interface for Music-on-Hold and
Back-ground Music
One External Page interfaces
One general-purpose Dry contact
Three universal expansion slots, a MEM(MCP1 or MEM3 or MEM4) card slot, a 2
SLI card slot and a MISC(MISC 1(2) or MISC 3(4)) card slot
2.1.1 Ring Generator Unit RGU1 or RGU2
Two kinds of sinusoidal-waveform Ring Generator Units are available. RGU1 drives 3W
ring signals while the other provides 20W ring signals. The larger unit is required when a
large number of single line telephones are operation behind the system.
2.1.2 MISC Card
MISC 1 or MISC 2 Card (only use in the iDCS 100 or DCS Compact-II system)
One dedicated slot in the Basic KSU is for an MISC card and two kinds of MISC cards are
available. MISC 1(2) cards only used together with the MEM4(or MEM3 or MEM2: iDCS
100 or DCS Compact II SYSTEM) cards. New MISC 1A(2A) Card installed with 500
MODEM is not operation SIO 1 RS232C.
The MISC 1 card contains one additional External Music Interface for MOH or BGM, one
additional External Page Interface, one Alarm Sensor Detection circuitry, 4 channels
DTMF receiver, three General-purpose Dry contact relays, 8 channel FSK Caller-ID
Receive, two RS232C Serial interfaces with connectors for PCMMC and SMDR and
external local MODEM interface. The MISC 2 card is similar to the MISC 1 card but is
also equipped with a built-in 4-ch AA function.
It is strongly recommended that this card be used in situations requiring heavy single line
telephone use.
MISC 3 or MISC 4 Card (only use in the OfficeServ 100 system)
Many miscellaneous function DTMF receiver(4ch), BGM, PAGE, Common Purpose
Relay(3port), CID Rx, 500 MODEM(option) are MISC 3. MISC 4 support MISC 3 feature
and 4 Channel AA. MISC 3(4) SIO Port no serviced, MCP1 SIO Port serviced
consequently. New feature support the FSK Caller ID sender to SLT: With total 16 Channel
for FSK CID Tx & Rx ports.
Only used 500 MDOEM Optional D-board and 3 pin cable connected the MCP1 board for
MP serial data(TXD, RXD ,GND) signaling to the MODEM.
500 MODEM Card (common use the OfficeServ 500)
One built-in 500 MODEM card can be installed in a MISC 3(or 4) card for OfficeServ 100
system or MISC 1A(or 2A) for iDCS 100 or DCS Compact-II system..
© SAMSUNG Electronics Co., Ltd.
2-3
CHAPTER 2. Hardware Descriptions
PLL Card
Any ISDN card, that is a BRI or a PRI, requires the PLL card which can be installed in a
dedicated place on the KSU mother board.
MEM3 Card (operation by the iDCS 100 system)
MEM3 card has EPROM memory to support new features Window PC-MMC, ITM3 &
TEPRI cards
MEM4 Card (operation by the iDCS 100 system)
MEM4 card with LAN interface module, no selectable options. The LAN module is
required to expand the system memory, to provide SIO ports 1EA, and a 10/100 BASET LAN interface processor.
MEM4 card has Flash memory to support new features Window PC-MMC, ITM3, TEPRI
cards and Networking solution by TE/PRI, Program/Database up/download by LAN
interface.
MCP1 Card (operation by the OfficeServ 100 system)
MCP1 card is the main processor card with a 32 bit processor, and controls the overall
operation of the OfficeServ 100 system, supported with RJ45 LAN Interface, DB9 SIO
Connecter and IPC(Inter Processor Communication) with SP(68EC000 in the 008Base
Board), no selectable options. The LAN module is required to expand the system memory,
to provide SIO ports 1EA, and a 10/100 BASE-T LAN interface processor.
Support with most of current iDCS 100(DCS Compact II) cards.
Include new MISC 3(4), MGI3 and 4WLI cards & other cards, except MISC 1/2,
ITM3 Cards.
The procedures for mounting and connecting connectors, LED indicator, memory back-up
ON/OFF switch, and only used 500 MDOEM optional d-board and 3 pin cable connected
the MCP1 Card for MP serial data(TXD, RXD ,GND) signaling to the 500 MODEM.
2-4
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
2.2 Expansion Cabinet
One metal Expansion cabinet can be attached to the KSU for expansion. Expansion A type
consists of three Universal expansion slots and one DCS card slot for TEPRI(PRI) or SVM
i-8. Expansion B type consists of two Universal expansion slots and two DCS card slot for
TEPRI(PRI) or SVMi-8. The Expansion cabinet connects to the KSU via a 64-pin flat
cable, two 2-wire power connections and a F-GND connection.
It contains a 50-pin champ connector for external connections. Please be noticed that a
DCS card has its own connector.
2.3 Interface Cards
2 SLI Card
The 2 SLI card is installed in a dedicated slot on the KSU mother board. The card provides
two single line telephone interfaces equipped with Long Line protection and the ability to
provide a loop disconnect signal.
3 TRK Card
The 3 TRK card provides three loop start C.O. interfaces with optional Caller ID relays.
The first two C.O. interfaces are equipped with PFT relays. Each interface contains an
interface for MPD or PRS which is optional. The MPD or PRS hybrid chips of the DCS
system can be used.
6 TRK Card
The 6 TRK card provides six loop start C.O. interfaces. The first two C.O. interfaces are
equipped with PFT relays. Each interface contains an interface for MPD or PRS which is
optional. The MPD or PRS hybrid chips of the DCS system can be used.
4 BRI Card
The 4 BRI card contains four Basic Rate access ports, i.e., eight ISDN channels. Protocol is
compatible for Euro-ISDN BRI. For S0 application, power feeding to ports is selectable by
programming.
2 BRI Card
The 2 BRI card contains two Basic Rate access ports, i.e., four ISDN channels. Protocol is
compatible for Euro-ISDN BRI. For S0 application, power feeding to ports is selectable by
programming.
TEPRI or PRI Card
The PRI card contains one Primary Rate access ports, i.e., thirty ISDN channels. Protocol
is compatible for Euro-ISDN PRI. TEPRI card must be equipped into the last slot of the
expansion cabinet. When programmed as an E1 this card provides up to 30 trunk circuits in
any combination of the following:
© SAMSUNG Electronics Co., Ltd.
2-5
CHAPTER 2. Hardware Descriptions
Loop start lines
DID(Direct Inward Dialing)
Ground start lines
E & M tie lines or two way DID calling
8 DLI Card
The 8 DLI card provides eight DLI ports.
8 SLI Card
The 8 SLI card provides eight SLI ports for industry-standard single line telephones and the
ability to provide a loop disconnect signal. Please note that this card does not provide Long
Line protection.
6 MWSLI Card
The 6 MWSLI card provides six SLI ports for industry-standard single line telephones and
the ability to provide a loop disconnect signal and a message waiting signal. Please note
that this card does not provide Long Line protection.
ITM3 Card
The number of the installed ITM3 card is limited to one in the iDCS 100 system(MEM3 or
MEM4).
The ITM3 card supports 8 VoIP channels. These channels are H.323 compliant and are
used in conjunction with either the G.723 or G.729 voice compression protocols. The ITM3
card can be installed in the universal slot on the Basic KSU.
SVMi-4 Card
The SVMi-4 is a self contained plug in voice mail and auto attendant card for the OfficeServ 100.
It is designed to meet the demands of the sophisticated voice mail user without sacrificing
simplicity.
The SVMi-4 may act as an Auto Attendant system only, a Voice Mail System only or both.
Out of the box the SVMi-4 can handle 2 calls simultaneously. It can be easily
upgraded to handle up to 4 calls simultaneously. No external line or power
connections and necessary, these are accomplished directly through phone system
At this time of this writing the memory capacity is about 5 hours, although change in
technology will allow for additional storage as time go on. Only one card is permitted
per system and it can be installed in any universal card slot.
2-6
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
SVMi-8 Card
The SVMI-8 Voice Mail system is a fully integrated Auto Attendant/Voice Mail/Fax
System on a single DCS circuit card. This optional card is designated the SVMi-8 and
provides 4 or 8 channels of communication. Only one card is permitted per system and it
can be installed in DCS slot on the expansion cabinet.
This fully featured self contained system is connected directly to the DCS data bus and
communicates with the DCS Processor. This design means that installation time is
minimized, operation is streamlined and many features can be implemented that are not
normally possible with older conventional stand alone Voice Mail/Auto Attendant systems.
All power to run this self contained system comes from the power supply. Each of the
power supply is rated according to the number of stations it will support. When SVMI-8 is
installed it counts as eight stations of the PSU rating regardless of the number of Voice
Processing Modules installed
MGI3 Card
The MGI3 card supports the VoIP Gateway, which enables telephone calls through the
Internet. When mounted with the 500 MGI3 D-board, the MGI3 card can support up to
16 Internet telephone(VoIP) ports by adding 8 channels of Internet telephone ports.
The main features and characteristics of the MGI3 card are summarized below.
Up to 3 cards MGI3 shall be installed in the Basic cabinet 3 universal slot.
Flash memory and data memory basically mounted for program
Echo cancellation function supported preventing echo sounds
Silence suppression function supported preventing data transfer on the network
for the brief silent intervals between words during calls.
Supports G.711, G.723.1(6.3k) and G.729A for Audio CODEC
Supports T.38 regarding Fax
4WLI Card
The 4WLI card provides wireless solution to the OfficeServ 100 system, and provides cable
interface between the system and WLAN Base Station(WBS24), which is the access point for
WLAN. One 4WLI shall be installed in the Basic cabinet 3 universal slot and4WLI can
interlock up to 4 WBS24s. A single 4WLI board supports up to 16voice channels.
The main features of the 4WLI card are summarized below.
Provides cable interface(voice and signaling data) between the Access
Point(WBS24)and system
Performs initialization to service VoIP over WLAN
Manages information on all voice terminals and provides service only for the
authorized terminals
Initial registration service for the wireless IP phone(WIP-5000M)
Call service for voice terminals
Supports mobility and handover between WBS for voice terminals
© SAMSUNG Electronics Co., Ltd.
2-7
CHAPTER 2. Hardware Descriptions
2.4 Station Equipment
2.4.1 iDCS Series Equipment
2.4.1.1 28 Button iDCS Phone
32 character display(2 x 16) with three associated soft buttons and a scroll button
28 programmable buttons with tri-colored lights
Four fixed function buttons
Terminal Status Indicator
Built-in speakerphone
Eight selectable ring tones
UP/DOWN buttons for digital control of speaker, handset and ringer volumes
Desk-or wall-mounted
Available in dark gray or light gray
Figure 2.2 28 Button iDCS Keyset
2.4.1.2 18 Button iDCS Phone
32 character display(2 x 16) with three associated soft buttons and a scroll button
18 programmable buttons with tri-colored lights
Four fixed function buttons
Terminal Status Indicator
Built-in speakerphone
Eight selectable ring tones
UP/DOWN buttons for digital control of speaker, handset and ringer volumes
Desk or wall-mounted Available in dark gray or light gray
2-8
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
Figure 2.3 18 Button iDCS phone
2.4.1.3 8 Button iDCS Phone
32 character display(2 x 16) with three associated soft buttons and a scroll button
8 programmable buttons with tri-colored lights
Four fixed function buttons
Terminal Status Indicator
Built-in speakerphone
Eight selectable ring tones
UP/DOWN buttons for digital control of speaker, handset and ringer volumes
Desk-or wall-mounted
Available in dark gray or light gray
Figure 2.4 8 Button iDCS Keyset
© SAMSUNG Electronics Co., Ltd.
2-9
CHAPTER 2. Hardware Descriptions
2.4.1.4 64 Button iDCS AOM
64 programmable buttons with red lights
A maximum of 2 can be assigned to any phone to provide additional programmable
buttons
A maximum of 4 per DCS System
Available in dark gray or light gray
Figure 2.5 64 Button iDCS AOM
2.4.1.5 14 Button iDCS AOM
14 programmable buttons with red lights
A maximum of one can be assigned to any phone to provide additional programmable
buttons
Available in dark gray or light gray
Figure 2.6 14 Button iDCS AOM
2-10
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
2.4.1.6 12 Button Large LCD IP Phone
The DS-5012L phone is Large LCD phone
It supports data transfer, handset call and Full-Duplex speakerphone.
The USB Interface(shared with mobile phones) is also supported, and various features
are provided through the LCD.
The Navigation Buttons are provided along with the common buttons for convenient
button control, and the phone book and recording
Figure 2.7 DS-5012L
2.4.1.7 14 Button 2 Line LCD Phone
The DS-5014D phone is 2 line LCD digital phone
It has 14 programmable buttons for the subscriber to register the features preferred.
This phone supports handset calls and speakerphone calls
It is equipped with the navigation button that enables you to use the phone
functions(such as recently called numbers, recently received numbers, searching
numbers by name, setting forwarding calls, inquiring speed buttons, and setting alarm)
easily.
KDB-D/S/F connection is also supported.
Figure 2.8 DS-5014D
© SAMSUNG Electronics Co., Ltd.
2-11
CHAPTER 2. Hardware Descriptions
2.4.1.8 21 Button 2 Line LCD Phone
The DS-5021D phone is 2 line LCD digital phone
It has 21 programmable buttons for the subscriber to register the features preferred.
This phone supports handset calls and speakerphone calls
It is equipped with the navigation button that enables you to use the phone functions
(such as recently called numbers, recently received numbers, searching numbers by
name, setting forwarding calls, inquiring speed buttons, and setting alarm) easily.
KDB-D/S/F connection is also supported
Figure 2.9 DS-5021D
2.4.1.9 12 Button Large LCD IP Phone
The ITP-5012L phone is a Large LCD IP phone, which displays various information
on the LCD screen and is equipped with 12 selectable buttons.
The ITP-5012L phone provides voice communication through the previously installed
data network line, making installation of additional telephone lines unnecessary.
This phone is equipped with the Dial button, Volume button, and Conference button.
The Transfer button used for transferring a busy call to another subscriber, the Hold
button, the Speaker button for speaker calls, and the navigation button that allows you
to use the phone functions easily.
The Screen button for additional expansion function and the Scroll button for easily
searching long contexts displayed on the LCD screen are also provided.
The status indicator lets you know when a message or a call arrives, and each LED
displays if the Transfer/Hold /Speaker button is pressed, and the LCD screen displays
the call status and various information.
2-12
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
Figure 2.10 ITP-5012L
2.4.1.10 14 Button/21 Button 2 Line LCD IP Phone
The ITP-5000D series phone has 14/21 programmable buttons for the subscriber to
register the features preferred. Screen and is equipped with 12 selectable buttons.
This phone is equipped with the Dial button, Volume button, and Conference button.
The Transfer button used for transferring a busy call to another subscriber, the Hold
button, the Speaker button for speaker calls, and the navigation button that allows you
to use the phone functions easily.
The LCD screen displays the call status and various information, and the status
indicator notifies the status of the phone in the three colors of red, green, and yellow.
Figure 2.11 ITP-5014D
© SAMSUNG Electronics Co., Ltd.
Figure 2.12 ITP-5021D
2-13
CHAPTER 2. Hardware Descriptions
2.4.1.11 DS-5064B (64B AOM)
AOM is an accessory type digital station that extended the button and LED of a digital
phone.
DS-5064B is the improved model of the OfficeServ 500system 64B. Various functions
preferred by you can be set on each button of DS-5064B AOM.
Figure 2.13 DS-5064B
2.4.1.12 WIP-5000M (Mobile Phone)
The WIP-5000M(Wireless IP phone Mobile type) mobile phone is an in-plant wireless
mobile phone
It allows voice calls through the IEEE802.11b wireless LAN.
The WIP-5000M mobile phone serves as a wireless IP phone that transmits/receives in
a packet form satisfying the wireless LAN standard(Voice over WLAN) by voice
compression.
Handover is supported when moving between AP(WBS24), and data terminals such as
laptop PC can also be used in the same area.
WLAN
LAN
WLI
LD1
LD2
PWR
Figure 2.14 WBS24
2-14
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
Figure 2.15 WIP-5000M
2.4.2 DCS Series Equipment
2.4.2.1 LCD 24B Keyset
Built-in speakerphone
24 programmable keys(16 with tri-colored LEDs)
Four fixed function keys
32 character display(2 x 16) with three associated soft keys and a scroll key
UP/DOWN buttons for digital control of speaker, handset and ringer volumes
Eight selectable ring tones
Desk- or wall-mounted
Available in almond or charcoal
Figure 2.16 LCD 24B Euro Keyset
© SAMSUNG Electronics Co., Ltd.
2-15
CHAPTER 2. Hardware Descriptions
2.4.2.2 STD 24B Keyset
Built-in speakerphone
24 programmable soft keys(16 with tri-colored LEDs)
Four fixed function keys
UP/DOWN buttons for digital control of speaker, handset and ringer volumes
Eight selectable ring tones per keyset
Desk- or wall-mounted
Available in almond or charcoal
Figure 2.17 STD 24B Keyset
2.4.2.3 STD 12B Keyset
Built-in speakerphone
12 programmable soft keys(16 with tri-colored LEDs)
Four fixed function keys
UP/DOWN buttons for digital control of speaker, handset and ringer volumes
Eight selectable ring tones per keyset
Desk- or wall-mounted
Available in almond or charcoal
Figure 2.18 STD 12B Keyset
2-16
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
2.4.2.4 6B LCD Model Keyset
Built-in speakerphone
6 programmable keys
Four fixed function keys
UP/DOWN buttons for digital control of speaker, handset and ringer volumes
Eight selectable ring tones per keyset
Desk- or wall-mounted
Available in almond or charcoal
Figure 2.19 6B LCD Model Keyset
2.4.2.5 48 Button AOM
48 programmable keys
Available in almond or charcoal
One or two can be assigned to any DCS keyset to provide additional programmable keys
Figure 2.20 48 Button AOM
© SAMSUNG Electronics Co., Ltd.
2-17
CHAPTER 2. Hardware Descriptions
2.4.2.6 S-Phone
DS 24S Keyset
8 programmable keys with tri-colored lights: Used to call stations directly, to indicate busy
conditions of other stations, for One Touch dialing and many other system features.
Volume Control Keys: Used to set independent levels for handset, speaker,
background music, ring and page volumes.
Transfer Key
Redial Key
Microphone: For hands-free operation.
Hold Key
Speaker Key
16 programmable keys with red lights: Used to call stations directly, to indicate busy
conditions of other stations, for One Touch dialing and many other system features.
Speaker: For hands-free operation and ringing.
Figure 2.21A DS 24S Keyset
2-18
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
DS 24D Keyset
8 programmable keys with tri-colored lights: Used to call stations directly, to indicate
busy conditions of other stations, for OneTouch dialing and many other system features.
Volume Control Keys: Used to set independent levels for handset, speaker,
background music, ring and page volumes.
Transfer Key
Redial Key
Microphone: For hands-free operation.
Hold Key
Speaker Key
16 programmable keys with red lights: Used to call stations directly, to indicate busy
conditions of other stations, for One Touch dialing and many other system features.
Speaker: For hands-free operation and ringing.
Scroll Key: Used to scroll through displays.
Figure 2.21B DS 24D Keyset
© SAMSUNG Electronics Co., Ltd.
2-19
CHAPTER 2. Hardware Descriptions
2.4.2.7 Economic Keyset
Volume Control Keys: Used to set independent levels for handset, speaker,
background music, ring and page volumes.
Transfer Key
Redial Key
Microphone: For hands-free operation.
Hold Key
Speaker Key
Speaker: For hands-free operation and ringing.
Figure 2.22 Economic Keyset
2.4.2.8 Door Phone Interface Module (DPIM) & Door Phone
The DPIM adapts any DLI circuit for use with the door phone unit
Commonly used to request entry through locked doors(interior or exterior) or as a
room monitoring box
Provides contact control to be used with customer-provided electric door lock
Door phone is wall-mounted
Door phone is weather resistant
Figure 2.23 Door Phone Interface Module
2-20
Figure 2.24 Door Phone
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
2.4.2.9 Single Line Telephone
Data Port: selectable to share station extension or utilize a separate extension
On hook dialing
Message Waiting/Ring Indicator
Desk or wall mounted
Ring volume control,
Four available ring tones.
Available in almond and black
Figure 2.25 Single Line Telephone
Single line telephone set
This single line telephone set is FCC approved for direct connection to the public
telephone network.
FCC # A3LKOR-24627-TE-T REN 0.9B UL LISTED 19X9 FILE # ETI 8093
2.4.2.10 KDB-DLI
This is a small daughter board that can be installed only in the 12 or 24 button keyset.
The KDB-DLI will provide one additional DLI circuit for the connection of any digital
station device such as a keyset, add-on module or DPIM(Door Phone Interface Module).
This KDB-DLI will only operate when the keyset is connected to an 8 port DLI card so it
can use the second B channel. Each port on this card is intended for connection to one
telephone. Connecting multiple telephones to a port may result in incorrect operation or
damage to the card. See the installation manual Chapter 8 for details.
© SAMSUNG Electronics Co., Ltd.
2-21
CHAPTER 2. Hardware Descriptions
2.4.2.11 KDB-SLI
This is a daughter board that can be installed only in the 12 or 24 button keyset. The KDBSLI will provide one additional SLI circuit for the connection of any standard telephone
device. This KDB-SLI will only operate when the keyset is connected to an 8 port DLI
card it can use the second B channel. Each port on this card is intended for connection to
one telephone. Connecting multiple telephones to a port may result in incorrect operation
or damage to the card. See the installation manual Chapter 8 for details.
KDB-SLI board
The circuitry on a KDB-SLI does not provide a loop open disconnect signal or
have the over-voltage protection necessary for OPX operation.
2-22
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide
CHAPTER 3. Specifications
This chapter describes the technical data for the OfficeServ 100 hybrid/key telephone
system as follows.
Electrical Specifications KSU
Interface Cards
Station Equipment
3.1 Electrical Specifications
Table 3.1 Electrical Specifications
AC INPUT
220~240VAC, 50Hz, 3.0A
POWER CONSUMPTION(MAX)
140 WATTS MAX
DC OUTPUT
FUSE RATING 2AMP
+5 VOLTS 4.0 AMPS MAX
- 55 VOLTS 1.7 AMPS MAX(for SLT/KTS Feeding voltage)
- 54 VOLTS 0.4 AMPS MAX(for Battery charge)
3.1.1 Dimensions and Weights
Table 3.2 Dimensions and Weights
Height(mm)
Width(mm)
Depth(mm)
Basic(Single) Cabinet
464
365
148
7.5
Expansion(Two) Cabinet
464
467
148
12.5
DPIM
120
91
28
0.2
Door Phone
127
99
32
0.2
WBS24
328
80
41
0.5
43
126
19
0.1
WIP-5000M
© SAMSUNG Electronics Co., Ltd.
Weight(kg)
3-1
CHAPTER 3. Specifications
3.1.2 Environments
Table 3.3 Environments
Operating Temperature
32-104 °F/0-40 °C
Storage Temperature
13.1-158 °F/-10.5-70 °C
Humidity
10-90 % non-condensing
3.1.3 Cable Requirements
Table 3.4 Cable Requirements
EQUIPMENT
CABLE
AWG
MAX FEET
MAX METERS
Digital Keyset
1 PR. TWISTED
24
1300
400
Add-On Module
1 PR. TWISTED
24
1300
400
Single Line Station
1 PR. TWISTED
24
3000
1000
Door Phone
2 PR. TWISTED
24
WBS24
2 PR. TWISTED
24
330*
1300
100
400
Cable length
This is the maximum length of the cable between the door phone and the DPIM.
The DPIM can be installed up to 270 cable meters from the KSU.
3.1.4 System Tones
Table 3.5 System Tones
Tone
Frequencies
SVMi-8
Dial Tone
350 + 440 Hz
Continuous
Ring Back Tone
440 + 480 Hz
1 sec on + 3 sec off
Busy Tone
480 + 620 Hz
0.5 sec on + 0.5 sec off
DND/No More Tone
480 + 620 Hz
0.25 sec on + 0.25 sec off
Error Tone
480 + 620 Hz
0.25 sec of each tone
Confirmation Tone
350 + 440 Hz
Three bursts of tone 0.1 sec on + 0.1 sec
Transfer/CONF
350 + 440 Hz
0.1 sec on + 0.1 sec off
The details of system tones
The details of system tones may vary according to the specifications of each
country.
3-2
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
3.1.5 Keyset LEDs
Table 3.6 Keyset LEDs
Condition
LED Color
LED On
LED Off
Line Idle
Off
-
Off
Line In Use
Red/Green
Steady
-
Recall
Amber
500 ms
500 ms
Call On Hold
Red/Green
500 ms
500 ms
Ringing C.O. Call
Red/Green
100 ms
100 ms
Ringing Internal Call
Green
100 ms
100 ms
DND Indication
Red
100 ms ON/100 ms
500 ms
OFF for 500 ms
© SAMSUNG Electronics Co., Ltd.
3-3
CHAPTER 3. Specifications
This page is intentionally left blank.
3-4
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide
CHAPTER 4. Business Feature
Package
This chapter describes various features of the OfficeServ 100 system as follows.
System Features
Station Features
Display Features
Sample SMDR Printout without Caller ID
Sample SMDR Printout with Caller ID
Sample UCD Report
UCD Call Statistics
UCD Agent Statistics
Sample Traffic Report
Traffic Report Overview
Sample Alarm Report
DECT Service
© SAMSUNG Electronics Co., Ltd.
4-1
CHAPTER 4. Business Feature Package
4.1 System Features
Account Code Entry
Forced-Verified
Forced-Not Verified
Voluntary
Account Code Key
All Call Voice Page
Attention Tone
Authorization Codes
Forced
Voluntary
Auto Attendant†
Automatic Hold
Background Music
Cadence-Integrated Voice Mail
Call Activity Display
Call Costing
Caller Identification†
Caller ID
Calling Line Identification(CLI)
Calling ID Features
Name/Number Display
Next Call
Save Caller ID Number
Store Caller ID Number
Inquire Park/Hold
Caller ID Review List
Investigate
Abandon Call List
Caller ID on SMDR
Number to Name Translation
Call Forwarding
All Calls
Busy
No Answer
Busy/No Answer
Forward DND
Follow Me
To Voice Mail
Preset Destination
Call Hold
Exclusive
System
Remote
Call Park and Page
Call Pickup
Directed
Groups
Call Waiting/Camp-On
4-2
Centrex/PBX Use
Chain Dialing
Class of Service
Common Bell Control
Conference
Add On(5 Party)
Unsupervised
Computer Telephony Integration(CTI)
TAPI 2.1
Customer Set Relocation
Data Security
Database Printout
Dialed Number Identification Service(DNIS)
Direct In Lines
Direct Inward Dialing(DID)
E1/Copper
Day/Night Routing
Busy or Camp-On Option
Direct Inward System Access(DISA)
Direct Trunk Selection
Directory Names
DISA Security
Distinctive Ringing
Door Lock Release(Programmable)
Door Phones
E & M Tie Lines E1/Copper
Executive Barge-In(Override)
With Warning Tone
Without Warning Tone
Trunk Monitor or Service Observing
External Music Interfaces
External Page Interfaces
Flash Key Operation
Flexible Numbering
Hot Line
In Group/Out of Group
Incoming Call Distribution
Incoming/Outgoing Service
Individual Line Control
ISDN Service
Primary Rate Interface(PRI)
Basic Rate Interface(BRI)
Least Cost Routing
Live System Programming
From any Display Keyset
With a Personal Computer
Meet Me Page and Answer
Memory Protection
Message Waiting Indications
Microphone On/Off per Station
Music on Hold-Flexible
Music on Hold-Sources
Off Premises Extensions(OPX)
Operator Group
Overflow
Operator
Station Group
Override Code
Paging
Internal Zones(4)
External Zones(4)
All Internal
All External
Page All
Park Orbits
Primeline Selection
Private Lines
Programmable Line Privacy
Programmable Timers
Recalls
Remote Programming-PC
Ring Modes
Time Based Routing-Plans
Automatic/Manual
Holiday Schedule
Temporary Override
Ring Over Page
Secretary Pooling
Single Line Connections
Speed Dial Numbers
Station List(50 Max)
System List(500 Max)
Speed Dial by Directory
Station Hunt Groups(20)
Distributed
Sequential
Unconditional
Station Message Detail Recording(SMDR)
System Alarms
System Maintenance Alarms
System Directory
Toll Restriction
By Day or Night
By Line or Station
Eight Dialing Classes
Special Code Table
Toll Restriction Override
Tone or Pulse Dialing
Traffic Reporting
Transfer
Screened/Unscreened
Voice Mail Transfer Key
With Camp-On
Trunk Groups(11)
Uniform Call Distribution(UCD)†
UCD Groups
Call Statistics
Agent Statistics
Group Supervisors
Printed Reports
Universal Answer
Voice Mail-Inband Integration
Walking Class of Service
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
Optional hardware and software
Requires optional hardware and/or software. Ask your dealer for details.
4.1.1 System Feature Descriptions
4.1.1.1 Account Code Entry
Station users may enter an account code(maximum 12 digits) before hanging up from a call.
This account code will appear in the SMDR printout for that call record. Keyset users may
enter this code using an account code key without interrupting a conversation. Single line
telephone users must temporarily interrupt the call by hook-flashing and dialing the feature
access code. Manually entered account codes can be up to 12 digits long. In some cases
users can be forced to enter an account code and this account code may or may not be
verified as described below.
Forced-Verified
When set for this option the user must enter an account code for all outgoing calls.
The account code entered will be verified from a system list of 500 entries. Forced Verified
codes can contain the digits 0~9.
Forced-Not Verified
When set for this option the user must enter an account code for all outgoing calls, but the
account code is not verified against the system list. Non verified account codes can contain
the digits 0~9, and #.
Voluntary
In this case account codes are not required to make outgoing calls but may be used if
desired. This is also the method used to assign an account code to incoming calls.
These account codes can contain the digits 0~9, * and #.
4.1.1.2 Account Code Key
ACC(The Account Code) button can be programmed on any phone. This button can be
programmed with an extender and operates in three different ways depending on the
extender as follows:
Extender=000 When programmed with an extender of 000 the ACC button will operate in
the same manner as the ACCT button in the MCP-M version. That is to say the user will be
prompted to enter an account code when the button is pressed.
© SAMSUNG Electronics Co., Ltd.
4-3
CHAPTER 4. Business Feature Package
Extender=001~999 When programmed with an extender ranging from 001 to 999 the button
will, when pressed, automatically insert the account code contained in that bin of the
system account code list. This is known as One Touch account codes. This option can be
denied in system programming to prevent users from bypassing the security of system
account codes.
No Extender When programmed without an extender the button will, when pressed,
prompt the user to enter the bin number the system account code table where the account
codes are stored.
4.1.1.3 All Call Voice Page
Users can page all internal and all external paging zones at the same time by dialing the All
Page code. Keysets may be restricted from making or receiving pages in system
programming. A maximum of 40 keysets can be programmed in each internal page zone to
receive page announcements.
4.1.1.4 Attention Tone
To get your attention, a brief tone precedes all page announcements and intercom voice
calls. There are separate programmable duration timers for page and voice announce tones.
4.1.1.5 Authorization Codes
Authorization codes are used to give permission to make a call. A maximum of 250 four
digit authorization codes can be either forced or voluntary for OfficeServ 100. When used,
authorization codes will automatically change the dialing station’s class of service to the
level assigned to the authorization code. Authorization codes may be programmed to print
or not print on SMDR.
Forced
When a station is programmed for forced authorization, the user must always enter this
code before dialing is allowed. The dialed authorization code is verified from the system
list of 250 authorization codes on an OfficeServ 100.
Voluntary
Any station user can always enter an authorization code before they begin dialing.
The dialed authorization code is verified from a system list of 250 authorization codes for
OfficeServ 100.
4-4
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.1.1.6 Auto Attendant
The integrated digital AA(Automated Attendant) feature provides six ports per AA card and
four ports at MISC 4 for simultaneous answering and call processing. A maximum of five
cards can be installed in one system. Each sixteen professionally recorded announcements
inform callers of the progress of their calls. Several examples are the following: ‘I’m sorry.
There is no answer’, ‘That station is busy’, and ‘Invalid Number. Please try again’.
A maximum of four minutes of super capacitor backed(100 hours) random access memory
(RAM) provide up to 48 customer recordings for announcements or greetings. Twelve
individual announcements(boxes), each with its own dialing options, allow you to build
call routing branches as needed. Callers are routed through the branches by dialing
extension numbers or single digits. This system is compatible with SVMi-8.
Announcements recorded on one AA card
Announcements recorded on one AA card can not be played to callers on another
AA card.
4.1.1.7 Automatic Hold
While a keyset user is engaged on an outside(C.O.) call, pressing another trunk key, route
key or CALL button automatically places the call on hold when Automatic Hold is enabled.
Pressing TRSF, CONFERENCE, PAGE or a DSS key always automatically places a C.O.
call on hold. Intercom calls can be automatically held only by pressing TRSF or
CONFERENCE. Each keyset user can enable or disable Automatic Hold.
4.1.1.8 Background Music
Keyset users may choose to hear music through their keyset speakers when optional
external sources are installed. Each user may adjust this level by the use of a volume
control program at the selected keyset.
4.1.1.9 Boss/Secretary Service
Up to four secretaries can be assigned to an executive. The line designated as the executive
may not be assigned as a secretary of another executive. When the executive is busy or in
DND status, the call is automatically connected to the secretary.
Executive Answer Mode
In MCP1, the secretary can set the response mode for each executive. The response modes
include Ring Mode, Automatic Answer, and Voice Announce.
Executive Status
The status of an executive can be set by the executive or the secretary. Other persons can
verify the set status through Easyset Application.
© SAMSUNG Electronics Co., Ltd.
4-5
CHAPTER 4. Business Feature Package
Divert
Divert may only be set from the line designated as an executive. Press the [Divert] button
in idle mode to automatically transfer all incoming calls to the secretary.
Press the [Divert] button while ringing to transfer the incoming call to the secretary.
The Divert function is operated by a toggle button.
4.1.1.10 SVMI-8-Intergrated Voice Mail
The OfficeServ 100 can be equipped with Samsung’s proprietary integrated voice mail and
auto attendant card(SVMi Series). It provides 4-8(2-4) ports of voice processing,
expandable in four(two) port increments. Because it is built into the system it provides such
feature as one touch Call Record, Answering Machine Emulation and Voice Mailbox
Administration with interactive keyset displays. Ask your dealer for literature on SVMi-8.
4.1.1.11 Call Activity Display
The OfficeServ 100 will record and buffer all calling activity within the system. With a
CAD (Call Activity Display) key, the OfficeServ 100 will display a ‘snapshot’ of the
following information:
The maximum number of ports that have been used
The maximum number of trunks that have been used
The maximum number of stations that have been used
The current number of ports in use
The current number of trunks in use
The current number of stations in use
4.1.1.12 Call Costing
The OfficeServ 100 provides programmable call costing tables to calculate the cost of
incoming and outgoing calls. Rates are calculated by the number dialed, and may include
surcharges. Display keysets can be set to show the call duration timer or the call cost.
The SMDR report will show either the call duration or the call cost depending on the
station selection. One call handled by multiple callers will cost each call segment separately.
4.1.1.13 Caller Identification
The OfficeServ 100 supports two methods of identifying an incoming caller depending on
the circuit type as described below.
Caller ID
On an analog, loop start C.O. Line, calling party information is called Caller ID and is
available from the telephone company in two formats, Number only and Name and
Number, sometimes called Deluxe. The OfficeServ 100 is compatible with both formats.
Even if the telephone company only offers the number only, a name can be attached to the
telephone number of frequent callers via the CLIP translation table.
4-6
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
CLI (Calling Line Identification)
On ISDN circuits, calling party information is called CLI and is supported on both BRI and
PRI type circuits. The OfficeServ 100 only supports Number delivery and a name can be
attached the telephone number of frequent callers via the CLIP translation table.
4.1.1.14 Caller ID Features
The following features apply to all forms of Caller Identification, however, to make them
easier to read caller identification is referred to as Caller ID.
Name/Number Display
Each LCD keyset user can decide if he/she wants to see the name or number in the display.
Regardless of which one is selected to be seen first, the NND key is pressed to view the
other pieces of information.
Next Call
In the event that you have a call waiting or a camped-on call at your keyset, you can press
the NEXT key to display the Caller ID information associated with this next call in queue
at your station. Either the Caller ID name or number will show in the display depending on
your selection.
Save Caller ID Number
At any time during an incoming call that provides Caller ID information, you may press the
SAVE key. This saves the Caller ID number in the Save Number feature. Pressing the
SAVE number redial key will dial the Caller ID number. The system must be using LCR
(Least Cost Routing) to dial the saved number.
Store Caller ID Number
At any time during an incoming call that provides Caller ID information, you may press the
STORE key. This saves the Caller ID number as a speed dial number in your personal
speed dial list. The system must be using LCR to dial the stored number.
Inquire Park/Hold
Having been informed that an incoming call is on hold or has been parked, you may view
the Caller ID information before you retrieve the call. This will influence how you choose
to handle the call.
Caller ID Review List
This feature allows display keyset users to review Caller ID information for calls sent to
their stations. This list can be from ten to fifty calls in a first in, first out basis. The list
includes calls that you answered and calls that rang your station but that you did not answer.
When reviewing this list, you can press one button to dial the person back. The system must
be using LCR to dial the stored number.
© SAMSUNG Electronics Co., Ltd.
4-7
CHAPTER 4. Business Feature Package
There is an added option called CID REVW ALL in the User ON/OFF options. When set to
ON the feature will operate the same as described above. However, when set to OFF only
calls that are not answered(missed calls) at the station will be recorded in the Review list.
Investigate
This feature allows selected stations with a special class of service to investigate any call in
progress. If Caller ID information is available for an incoming call, you will know to whom
this station user is speaking. On outgoing calls, you can see who was called.
After investigating, you may barge-in on the conversation, disconnect the call or hang up.
Abandon Call List
The system has a system-wide abandon call list that stores Caller ID information for calls
that rang but were not answered. The list is accessed using the administrator’s passcode.
When reviewing this list, you are provided options to CLEAR the entry or DIAL the
number. You can see the NND key to toggle between the Caller ID name, number and the
date and time the call came in. The system must be using LCR to dial numbers from the
abandon call list. The abandoned call list will store up to 50 unanswered calls on
OfficeServ 100.
Caller ID on SMDR
The Station Message Detail Records report can be set to include Caller ID name and Caller
ID number for incoming calls. This format expands the printout to 113 characters.
Use a wide carriage printer or an 80 column printer set for condensed print.
Number to Name Translation
The system provides a translation table for 500 entries on OfficeServ 100. When the Caller
ID number is received, the table is searched. When a match is found, the system will
display the corresponding name.
4.1.1.15 Call Forwarding
This feature allows the user to redirect(forward) incoming calls. The calls can be redirected
to the attendant, a hunt group, voice mail, external number or another station user. If the
destination station is in DND(Do Not Disturb), the calling party will receive DND/Reorder
tone. Calls cannot be forwarded to a door phone. In OfficeServ 100 system, the external
number can be set to the forward destination for all kinds of forwarding. So External, CFB,
CFNR and CFU option is removed. When the destination is external number, the ICM EXT
FWD option must be set to ON. If not, the call forwarding does not accomplished.
4-8
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
All Calls
This type of forwarding is not affected by the condition of the station. All calls are
immediately redirected to the designated destination. If desired, the destination station may
redirect the call back to the forwarded station by using the transfer feature. The forwarded
station user can continue to originate calls as usual. If no key is programmed as Forward
All, the TRSF key lights steady when a Forward All condition is set.
Busy
This feature forwards all calls only when the station set is busy. The station user can
originate calls as usual.
No Answer
This feature forwards calls that are not answered within a preprogrammed time. The user
can originate calls as usual and receive call if present. The timer is programmable on a perstation basis to allow for differences in individual work habits.
Busy/No Answer
This feature allows the station user to use both types of forwarding simultaneously,
provided the destinations have already been entered in the usual manner.
Forward DND
This feature works with the Do Not Disturb feature. This allows calls directed to a station
in Do Not Disturb or One Time Do Not Disturb to forward immediately to another
destination.
Follow Me
This feature allows the user to forward all calls from another station to the user’s station or
change the forward destination to the user’s current location.
To Voice Mail
Each station may be programmed to allow or deny the ability to forward intercom calls to
voice mail. When denied, valuable message time in the voice mail system can be saved.
Preset Destination
If desired this feature provides for a permanent(preset) forward no answer destination for
each extension. It can only be programmed by the system technician or system
administrator. When any station does not have FWD/NO-ANSWER set, the call will ring
this preset destination if one is programmed.
© SAMSUNG Electronics Co., Ltd.
4-9
CHAPTER 4. Business Feature Package
4.1.1.16 Call Hold (Exclusive)
Outside calls can be placed on exclusive hold at any keyset by pressing HOLD twice
during a call. Calls placed on exclusive hold can only be retrieved at the keyset that placed
the call on hold. Intercom calls are always placed on exclusive hold.
4.1.1.17 Call Hold (System)
Outside calls can be placed on system hold at any station. Users may dial the access code
or press the HOLD button. Calls on system hold may be retrieved at any station.
4.1.1.18 Call Hold (Remote)
Outside calls can be placed on hold at a remote station. This feature allows calls to be
answered at one keyset and placed on hold at another station. This allows time for the user
to proceed to that station or allows the party that the call was intended for to have that call
placed at their station. The call or trunk button will flash at the remote hold station.
Intercom calls
Intercom calls cannot be remote held.
4.1.1.19 Call Park and Page
Each C.O. line has its own park zone. This simple method eliminates confusion and
ensures that a park zone is always available. Pressing the PAGE key parks the call
automatically. There are no extra buttons to press and there is no lost time looking for a
free zone.
4.1.1.20 Call Pickup
Directed
With directed call pickup, users can answer calls ringing at any station by dialing a code
plus that station’s extension number or by pressing the feature button and then dialing the
extension.
Groups
In addition, calls can be picked up from a station group in a similar manner. The group
pickup feature allows users to answer any call ringing within any pickup group. There are
20 pickup groups available on OfficeServ 100. A station cannot be in more than one pickup
group. To use this feature, station users either dial the access code or press the assigned
feature button followed by the pickup group number.
4-10
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.1.1.21 Call Waiting/Camp-On
Busy stations are notified that a call is waiting(camped-on) when they receive a tone.
The tone is repeated at a programmable interval. Keysets receive an off-hook ring signal
through the speaker and single line stations receive a tone in the handset. The volume of
the camp-on tone can be set by the station user. Camped-on calls follow Forward No
Answer if a Forward No Answer destination has been set.
Optionally any station can be programmed to automatically camp-on to a busy station
instead of having to press the camp-on button or dial a camp-on code.
4.1.1.22 Centrex/PBX Use
CENTREX and PBX lines can be installed in lieu of central office trunks. CENTREX and
PBX feature access codes including the command for hook-flash(FLASH) can be stored
under one touch buttons. Toll restriction programming can ignore PBX or CENTREX
access codes so that toll calls can be controlled when using these services.
4.1.1.23 Chain Dialing
Keyset users may manually dial additional digits following a speed dial call or chain
together as many speed dial numbers as are required.
4.1.1.24 Class of Service
The system allows a maximum of 30 station classes of service. Each class of service can be
customized in memory to allow or deny access to features and to define a station’s dialing
class. Each station can be assigned different classes of service for day and night operation.
4.1.1.25 Common Bell Control
The MISC card provides relays that may be programmed to control a customer-provided
common bell or common audible device. These contacts must be programmed as members
of a station group and may provide steady or interrupted closure.
4.1.1.26 Conference
The system allows six simultaneous conferences up to 5 parties each.
Add-On (5 PARTY)
Any combination of up to five parties(stations or outside lines) can be joined together in an
add-on conference. Parties may be eliminated or added after a conference has been
established.
© SAMSUNG Electronics Co., Ltd.
4-11
CHAPTER 4. Business Feature Package
Unsupervise
A station user may set up a conference with two or more outside lines and then exit the
conference leaving the outside lines connected in an unsupervised(trunk to trunk)
conference.
Split
A phone user can ‘split’ a conference into separate outside calls, then speak with each caller
privately. Then the Individual calls can be conferenced again in any combination.
Split
This feature requires individual trunk buttons and auto-hold must be enabled.
4.1.1.27 CTI (Computer Telephony Integration)
CTI allows integration between the OfficeServ 100 and a personal computer system or a
LAN(Local Area Network). Caller ID service is required for TAPI inbound call
applications that use the CID information to display computer records in conjunction with
the presentation of the call to the station on the OfficeServ 100.
TAPI 2.1
TAPI 2.1 is the method of integrating the OfficeServ 100 system to a computer. TAPI 2.1 is
a LAN based solution allowing computers to communicate directly to the telephone system
over the network system. This establishes a logical connection rather than a physical
connection between telephone and computer. It eliminates the cost and administrative
overhead of connecting every PC to a desktop phone. It emphasizes third-party call control.
(Example: calls can be tracked as they are transferred, making it more suited to large office
applications). TAPI 2.1 can emulate first-party type call control for the OfficeServ 100
system, rather than from the telephone as TAPI 2.0 does. For example, to make a call the
OfficeServ 100, rather than the telephone would dial the phone number, and the call would
be then transferred to the telephone.
4.1.1.28 Customer Set Relocation
Customer Set Relocation allows the customer to exchange or swap similar stations in the
OfficeServ 100 without wiring changes. All individual station assignments such as trunk
ring, station group, station COS, station speed dial, button appearances, call forwarding, etc.
will follow the Customer Set Relocation program.
4-12
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.1.1.29 Data Security
Single line extensions used with modems and facsimile machines can be programmed so
that they will not receive any system-generated tones that would disrupt data transmissions.
In addition, these devices receive DCS C.O. ringing pattern instead of intercom ring pattern.
Devices connected to an SLI card receive a disconnect signal upon termination.
4.1.1.30 Database Printout
A copy of the customer database can be obtained by using PCMMC. This information can
be directed to a printer or the PC screen and may be done either on-site or remotely.
A complete database or specific data blocks may be obtained.
4.1.1.31 DECT Service
The OfficeServ 100 system provides DECT cordless communications in a single office or
throughout a large commercial or industrial complex. To implement this service, you need
BSI card, DB(Daughter Board) card and DECT handsets. Users of this service meet
improved overall efficiency, since staff can be reached or make calls wherever they are.
4.1.1.32 DNIS (Dialed Number Identification Service)
When DNIS service is provided on an incoming trunk the OfficeServ 100 can route calls
based on the numbers received.
4.1.1.33 Direct in Lines
Outside lines may be programmed to bypass the operator(s) and ring directly at any station
or group of stations.
4.1.1.34 DID(Direct Inward Dialing) E1/Copper
The term DID or DID refers to four types of digit steered inbound call handling. These are
DID, Both Way DID, Dialed Number Identification service(DNIS and Direct Dial In(DDI).
The OfficeServ 100 supports all four types as described below.
DID is an inbound only service where multiple telephone numbers are assigned, usually in
blocks of twenty, to a single circuit or small group of circuits. These circuits can be single
pair analog circuits that will terminate on a DID card. The OfficeServ 100 DID card
supports up to four circuits. In addition the DID circuit can be a channel on a digital E1
service terminating on an OfficeServ 100 TEPRI card.
Both way DID is a service that combines DID service with normal outbound local
telephone service. This service is provided over E & M tie line circuits. These E & M tie
line circuits can terminate on either the iDCS E & M card or on a channel of a digital E1
circuit on an iDCS TEPRI card.
© SAMSUNG Electronics Co., Ltd.
4-13
CHAPTER 4. Business Feature Package
DNIS(Dialed Number Identification service) is a feature of 800 or 900 type numbers that
allows the number dialed by the caller to be identified in the telephone system by means of
a sequence of DTMF digits(usually four). This service terminates on E&M tie lines.
These E&M tie line circuits can terminate on either the iDCS E&M card or on a channel of
a digital E1 circuit on an iDCS TEPRI card.
DDI(Direct Dial In). This is the name given to the above three services when they are
provided over an ISDN PRI circuit.
4.1.1.35 DISA(Direct Inward System Access )
Users can call in on specific DISA lines at any time, input a security code and receive
system dial tone. Users can now place internal calls or if permitted, calls using C.O. lines.
The caller must have a tone dial phone and know his/her DISA security code. DISA lines
can be used as both way lines or incoming only and may be active in day mode, night mode
or both. The C.O. lines used for DISA must have disconnect supervision.
4.1.1.36 Direct Trunk Selection
Each station can be allowed access to or denied access from a trunk or trunk group by
access code when LCR is activated. When restricted, the station user must use a trunk key
or a route key.
4.1.1.37 Directory Names
Each station, station group and C.O. line may be assigned a directory name(maximum 11
characters). In addition, each personal speed dial number, system speed dial number and
entry in the DID translation table may be assigned a name(maximum 11 characters).
These names are displayed during calls with these ports and in the case of station and speed
dial names, can be used to originate calls. See the Dial by Name feature(Station Features).
4.1.1.38 DISA Security
Telephone fraud and long distance theft are a serious concern. The OfficeServ 100 provides
a strong DISA security system. If an incorrect DISA passcode is entered repeatedly(as is
the case with ‘hackers’), the DISA system can be automatically disabled temporarily.
Both the number of incorrect passcode attempts and the time that DISA is disabled are
programmable. In addition, all failed attempts to access DISA print on SMDR(if provided)
with a ‘DE’ DISA error flag.
4.1.1.39 Distinctive Ringing
A user knows the type of call received by the type of ring heard. Outside calls have a single
ring repeated while internal calls have a double ring repeated.
In addition any trunk or station can be programmed to ring a keyset with a predefined ring
tone(1-8) or a single line port with a predefined SVMi-8(1-5) selection. This provides for
easy identification of special lines or extensions that ring your phone.
4-14
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.1.1.40 Door Lock Release (Programmable)
After answering a call from the door phone, users can dial a code to activate a contact
closure. This can be used to operate a customer-provided electric door lock release
mechanism. The contact closure timer is programmable from 100-2500 ms.
4.1.1.41 Door Phones
The DPIM provides for connection of a door phone to a DLI port. Pressing the button on
the door phone produces a distinctive ring(three short rings repeated) at the assigned station
or station group. If not answered within a programmable time, the system releases the door
phone and stops the ringing. Stations may call the door phone directly and monitor the
surrounding areas. Door phones follow the system ring mode plan.
4.1.1.42 Easyset Interface
Easyset Interface supports the interlocking of Easyset Application.
Easyset Application is used for easily setting the buttons and functions of the digital/IP
phone through the PC.
Various convenient features such as the SMS(Short Message Service) and diary are added
to the Easyset Application.
4.1.1.43 E & M Tie Lines (E1/Copper)
Your office can be connected to another office with a tie line. Use it to make calls to
stations in the other system. If programming allows, you can access lines in the other
system to make outside calls. Tie line calls can be put on hold, transferred and conferenced
in the same way as are other outside calls. Users accessing the tie line from the other
system can get a line in your system and make outgoing calls. These calls can be controlled
by assigning a dialing class to the tie line. Your local telephone company may use E & M
tie lines to provide DID service. In this case these tie lines can be programmed to follow
the DID translation table. See DID. Translated E & M tie line calls have Day and Night
routing capabilities.
4.1.1.44 Executive Barge-in (Override)
The feature allows specially programmed stations with a barge-in key to override the
automatic privacy of another station or outside trunk. Programming allows barge-in with or
without a warning tone. Stations may also be programmed as ‘secure’ so that they cannot
be barged-in on.
With Warning Tone
When the barge-in with tone option is set, the barging-in keyset has its microphone on and
the barged-in on station receives an override display. A double burst of warning tone
sounds and repeats every ten seconds. This feature does not work from single line sets.
© SAMSUNG Electronics Co., Ltd.
4-15
CHAPTER 4. Business Feature Package
Without Warning Tone
When the barge-in without tone option is set, the barging-in keyset has its microphone
muted and the barged-in on station does not receive an override display. This feature does
not work from single line sets.
Trunk Monitor or Service Observing
This feature allows the user who barged-in to retain the trunk call after the original station
has hung up.
4.1.1.45 External Music Interfaces
The OfficeServ 100 system provides up to two inputs for connecting to customer provided
external music sources. One is located on OfficeServ 100 base board which is selectable
using internal music source or external music source by shunt pin setting. Another is
located on the MISC card.
These sources can be used to provide background music, or any of the varied MOH(Music
On Hold) uses.
4.1.1.46 External Page Interfaces
The OfficeServ 100 base board provides one external page output and the OfficeServ 100
MISC card provides an additional external page output and three relays which can be used
to control the page zone control. Multiple relays may be assigned to each zone.
4.1.1.47 Flash Key Operation
While a user is on an outside line, pressing the FLASH key will flash the central office or
PBX. This is used for custom calling features on C.O. lines or in conjunction with
CENTREX/PBX operation. System programming allows individual flash times for C.O.
and PBX lines. When C.O. or PBX flash is not required, setting the timers for two seconds
releases the existing call and returns dial tone to make a new call.
4.1.1.48 Flexible Numbering
System programming allows stations to have two, three or four digit extension numbers
beginning with the digit 2 or 3. Default extension numbers begin with 201. Station group
numbers can be two or three digits beginning with the digit 5.
Using digits other than 2, 3 or 5 will require the technician to change other feature access
codes in the system default numbering plan. User guides will need to be modified as these
are all written using the OfficeServ 100 default numbering plan.
4.1.1.49 Hot Line
Stations can be programmed to call a pre-defined station or station group whenever that
station goes off-hook. A hot line delay timer of 0-250 seconds can be programmed to allow
sufficient time to make a different call.
4-16
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.1.1.50 Group Conference
The GCONF button is used to automatically call the preset number and include the person
into the conference when he or she answers the call. This function may only be used for
preset extensions, and up to five conference groups can be assigned to an extension. Up to
five persons, including the user may be assigned to a conference group. The Trunk line,
which can identify if the other party answers the call, shall be used to ensure normal
service when calling external numbers.
4.1.1.51 In Group/Out of Group
Individuals assigned to a station hunt group may temporarily remove their telephones from
the group by pressing the In/Out of Group button providing that there is someone still in
the group.
The OfficeServ 100 system has a system wide option to allow all members to log out of a
station group. Stations out of a group will not receive calls to that group but will continue
to receive calls to their individual extension numbers. When desired, the user may put
him/herself back into the group by pressing the button again. Users who do not have this
button may dial the access code and the group desired. A station user is allowed to be in
several groups, providing a key and the extender of that group are assigned for each group
on the user’s phone.
4.1.1.52 Incoming Call Distribution
Incoming calls can be assigned to ring a distributed station hunt group. This allows all
members of the group to share the call load.
4.1.1.53 Incoming/Outgoing Service
Outside lines are available for incoming or outgoing service. Programming allows any
outside line to be used for incoming calls only, outgoing calls only or both way service.
4.1.1.54 Individual Line Control
Each station in the system can be individually programmed to allow or deny dialing out as
well as allow or deny answering for each outside line.
4.1.1.55 IP Phone Interface
In OfficeServ 100 system, the IP phone Interface supports IP phone interlocking.
An additional MGI(Media Gateway Interface) port is not required for calls between Local
IP phones, but a separate MGI card must be installed for calling an existing station.
There is one type of MGI cards, MGI3. Up to three cards can be installed per system.
The MGI3 card is required for Internet FAX.
© SAMSUNG Electronics Co., Ltd.
4-17
CHAPTER 4. Business Feature Package
4.1.1.56 ISDN Service
PRI (Primary Rate Interface)
The OfficeServ 100 supports Primary Rate Interface ISDN. PRI allows simultaneous data
calls, calling party and calling line identification, high speed call setup and disconnect are
among the benefits of ISDN calling. The 30+D configuration of ISDN allows call
information to be delivered via the data channel(the ‘D’ of 30B+D) thus leaving the bearer
channels(the ‘B’ of 30B+D) available for single use or combined use to provide a wider
bandwidth for data and video.
BRI (Basic Rate Interface)
The OfficeServ 100 BRI card supports trunk or station level BRI .Trunk or station BRI use
is software programmable. BRI allows simultaneous data calls, called party and calling
number identification, high speed call setup and disconnect are among the benefits of ISDN
calling. The 2B+D configuration of ISDN allows call information to be delivered via the
data channel(the ‘D’ of 2B+D) thus leaving the bearer channels(the ‘B’ of 2B+D) available
for single use or combined use to provide a wider bandwidth for data and video.
4.1.1.57 Large LCD Phone Interface
In OfficeServ 100 system, the Large LCD phone Interface supports the Large LCD phone.
The wide LCD screen of the Large LCD phone provides various features such as Virtual
AOM, phone Book, LCD Navigation similar to that of a mobile phone, and Enblock
Dialing.
4.1.1.58 Least Cost Routing
LCR(Least Cost Routing) is the ability to automatically select the most cost effective
central office route for the outside number dialed by any station. The OfficeServ 100 LCR
program includes the following features:
Option to use or not use LCR or a tenant basis
Programmable LCR access code
Digit analysis table 500 entries each with ten digits for an OfficeServ 100
Routing by time of day and day of week(4 time bands per day)
Routing according to individual station class
Modify digits table 100 entries for an OfficeServ 100.
Flexible trunk group advance timer
Option to use or not use trunk group advance warning tones
4-18
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.1.1.59 Live System Programming
The system can be programmed from any display keyset or personal computer without
interrupting normal system operation. There are three levels of programming: technician,
customer and station. The technician level has access to all programs and can allow the
customer access to system programs as needed. Technician and customer access are controlled
by different security passcodes. Programming from a PC requires the PCMMC program.
4.1.1.60 Meet Me Page and Answer
After a user makes a Meet Me Page, the user may remain off-hook to allow the paged party
to meet the user for a private conversation.
4.1.1.61 Memory Protection
In the event that power is lost to the system, all customer data contained in memory is
retained by the use of a ‘super capacitor’ for approximately 7 days. In addition, the
PCMMC computer program may be used to produce a backup copy of the customer data.
Additionally, the Smart Media card may be used to store the system database.
4.1.1.62 Message Waiting Indications
When calling a station and receiving a busy signal or the no answer condition, the caller
can leave an indication that a message is waiting. The message button will flash red at the
messaged keyset.
A single line phone will receive a distinctive message waiting dial tone. Five message
waiting indications can be left at any station.
4.1.1.63 MicroPhone On/Off Per Station
The microphone can be disabled at any keyset. When the microphone is disabled, the
keyset cannot use the speakerphone, although on-hook dialing and group listening are still
possible.
4.1.1.64 Music on Hold-Flexible
The OfficeServ 100 allows its music sources to be used in a very flexible manner as follows:
Each keyset can have a designated music source for playing as BGM(Background
Music) through the keyset speaker.
Each Station can have a designated music source for playing to callers placed on
Exclusive hold at that station.
Each Trunk can have a designated music source for playing to callers placed on hold.
This setting is overridden by some of the other settings such as station music on hold,
and UCD MOH.
Each UCD group can have a designated music source to be played while a caller is in queue.
© SAMSUNG Electronics Co., Ltd.
4-19
CHAPTER 4. Business Feature Package
4.1.1.65 Music on Hold-Sources
The OfficeServ 100 provides for up to six different types of Music on Hold source
including silence or ‘NONE’ as listed below:
None: No audio is played to the listener
Tone: A tone or ‘beep’ is repeated at a programmable interval
Chime: A music chime source located on the Base board is played to the listener.
External source: An external source connected to a MISC card, such as a digital
announcer or radio, is played to the listener.
Digital Announcement on AA card: If the system is equipped with an AA card the
last port of this card can be flagged as a MOH source and used to repeatedly play a
message recorded on the AA card to the listener.
Voicemail Sound File: If the OfficeServ 100 system has an optional SVMI-8 card
installed, up to 100 custom recorded sound files from the Voice Mail card can be used
for MOH sources. For information on creating the sound files see SVMI-8 System
Administrator Manual-Recording greeting by number. If you select this option be
advised that each VMMOH source requires a dedicated SVMI-8 port/channel.
4.1.1.66 Networking (PRI/Q-SIG)
The OfficeServ 100 networking feature package allows an OfficeServ 100 system to be
connected together with some basic feature transparency. The physical connection between the
systems is via a proprietary PRI connection(TEPRI card must be used) and is based on the QSIG specification. The following features are supported between two networked systems.
CCBS(Call Completion, Busy Station)
also known as Callback or Busy Station Callback. When a station in one system calls a
station in another system across the network link and the destination station is busy the
calling station can set a Callback to the busy station. When the busy station becomes idle
the system will notify the callback originating station by ringing that station and when the
originating station answers, the system will call the destination station.
CCNR(Call Completion, No Response)
also known as Callback or No Answer Callback. When a station in one system calls a
station in another system across the network link and the destination station does not
answer the calling station can set a Callback to the called station. When that station
indicates the user is present by becoming busy then idle the system will notify the callback
originating station by ringing that station and when the originating station answers, the
system will call the destination station.
CFB(Call Forward Busy)
This is a different feature from the normal call forward busy and is only used when the
forward destination is in a different node of the network.
The operation of the feature is the same as the normal forward busy where when the
forwarded station is busy a calling station will be forwarded to the forward destination.
4-20
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
CFNR(Call Forward No Response)
This is a different feature from the normal call forward no answer and is only used when
the forward destination is in a different node of the network. The operation of the feature is
the same as the normal forward no answer where when the forwarded station does not
answer after a programmed amount of time a calling station will be forwarded to the
forward destination.
CFU(Call Forward Unconditional)
This is a different feature from the normal call forward all and is only used when the
forward destination is in a different node of the network. The operation of the feature is the
same as the normal forward all where all calls to the forwarded station will be forwarded to
the forward destination.
Forward External
This feature operates in the same manner as a non networked system with the exception
that, because calls across a network link are trunk calls, network calls do not follow the
ICM FWD EXT ON/OFF setting in MMC 210. It is therefore suggested that this setting be
set to ON in a networked switch to avoid confusion in operation between networked and
non networked calls.
Call Intrusion(Barge In)
This feature operates in the same manner as in a non networked switch.
Call Offer/Call Waiting(Camp On)
This feature operates in the same manner as in a non networked switch. When a called
station is busy the caller can press a camp on key and appear as a ringing call on the second
call button. The Auto camp on feature will not work on calls across a network link if set to
ON in MMC 110.
Call Transfer
Calls answered in one network node can be transferred to a station or station group in
another network node.
Transfer Retrieve
Calls on Transfer Hold during a screened transfer can be retrieved by pressing the call
button for that call.
Transfer Recall
Calls transferred across a network link will recall to the transferring station after the
originating systems transfer recall timer expires. After recalling, if not answered prior to
that systems attendant recall timer expiring, the call will recall to that systems designated
operator group. Attendant recalls will not recall to a ‘Centralized Attendant’.
© SAMSUNG Electronics Co., Ltd.
4-21
CHAPTER 4. Business Feature Package
DID with Pass Through
Incoming DID, DNIS or DDI calls can be routed through one switch across a network link
to be processed by the DID table of the destination switch.
DND(Do Not Disturb)
This feature operates in the same manner as in a non networked switch. There is an option
in MMC 823 to determine the type of DND tone sent across the network link.
Caller ID
Caller ID in its various forms that are currently available(Analog CID Name and Number,
ANI Number, PRI Name and Number and BRI number) will be transported across the
network link with the original call.
Centralized Attendant
This feature basically allows a user in any switch to dial ‘0’ and ring at the designated
Central attendant group. Each system on the network requires its own designated attendant
group for local usage, recalls and the like.
Intercom Calling/Uniform dialing plan
Station to station and station to group calls can be made across the network link without
having to dial an access code for a call within the network. LCR can also be programmed
to route calls across a network link to access local trunks in another networked system.
Centralized Voice Mail with Message Waiting Lights
This feature will only operate with SVMi-8 and/or SVMi voicemail systems only. Users in
one node can call forward(CFNR, CFB & CFU) to the SVMi-8 group in a different switch
and messages left in that switch will be indicated on the VMSG key in the origination
switch. Messages can be returned to the SVMi-8 or SVMi voice mail system.
4.1.1.67 OPX (Off Premises Extensions)
A single line(tip and ring) extension from an 4SLI card may be connected to telephone
company-provided OPX circuits to remote locations. 8SLI cards and KDB-SLIs do not
support off premises extensions.
4.1.1.68 Operator Group
The operator group can contain 32 stations to answer incoming calls. Calls to this group
can be set for distributed, sequential or unconditional ringing. Operators can use the In/Out
of Group feature to meet flexible operator requirements. Operator groups are selectable per
ring plan.
4-22
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.1.1.69 Overflow
Operator
When calls ringing a operator group go unanswered, they can overflow to another
destination after a programmed period of time. The operator group has its own timer.
The overflow destination can be a station or station group.
Station Group
When calls ringing a station group go unanswered, they can overflow to another destination
after a programmed period of time. Each station group has its own timer. The overflow
destination can be a station or station group.
4.1.1.70 Override Code
This feature allows users to make emergency outside calls from a station that has a forced
code such as Account code or authorization code enabled but without requiring them to
enter a forced code. The basis of this feature is an override code table containing 8 entries
of up to 14 digits each. The OfficeServ 100 will examine digits that are dialed from a
station to see if they match any entry in the Emergency Number table. If the digits match
the table, the system will process the call without requiring a forced code.
4.1.1.71 Paging
System software allows the use of four internal and four external paging zones.
Stations can page any individual zone, all internal zones, all external zones or all zones
simultaneously. Using system programming, each station may be allowed or denied the
abilities to make and/or receive page announcements to any zone or combination of zones.
4.1.1.72 Park Orbits
The system has 10 park orbits(0-9). These orbits can be used to park calls prior to paging
and allows the call to be retrieved by dialing a park code plus the orbit number.
Calls parked in this manner can also be retrieved by dialing the park pickup code 10 plus
the station or trunk number. This feature is in addition to Call Park and Page.
4.1.1.73 Prime Line Selection
Any station can be programmed to select a specific line, trunk group, telephone number,
station or station group when the handset is lifted or the speaker key is pressed(same as Hot
Line feature).
4.1.1.74 Private Lines
For private line use, stations can be prevented from dialing and/or answering any line.
© SAMSUNG Electronics Co., Ltd.
4-23
CHAPTER 4. Business Feature Package
4.1.1.75 Programmable Line Privacy
Each outside line can be programmed to ignore the automatic line privacy. This allows up
to four other parties to join your conversation by simply pressing the line button.
This is similar to 1A2 key telephone operation.
4.1.1.76 Programmable Timers
There are over 50 programmable system timers to allow each installation to be customized
to best fit the end user’s application.
4.1.1.77 Programmed Message Service
Programmed Messages can be set on each extension. The Programmed Messages are
displayed on the LCD screen when call arrives from another extension. 15 messages are set
at the system level and 5 messages are set separately for each extension.
4.1.1.78 Recalls
Calls put on hold, transferred or camped-on to any station will recall to the originating
station if not answered within a programmable time. A recall that goes unanswered for the
duration of the attendant recall timer will recall to the system operator group. Hold, transfer,
camp-on and attendant recalls have individual programmable timers. Calls recalling to
buttons with tri-colored LEDs will flash amber.
4.1.1.79 Remote Programming-PC
Remote programming allows the technician to access the system database from a remote
location for the purpose of making changes to the customer data. Customer-provided modems
and a PC using an optional software package will be needed to implement this feature.
4.1.1.80 Ring Modes
Time Based Routing- Plans
Each C.O. line can be programmed to ring at any station or station group. Each line can be
assigned a ring destination based on six different ring plans based on time of day and the
day of the week.
Automatic/Manual
Ring destinations will automatically change based on time of day and day of week. At any
time the system can be manually forced into a specific ring plan. It will remain in this ring
plan until manually taken out.
Holiday Schedule
The system has a table of 60 dates that are used to define holidays. On a date designed as a
holiday the system will remain in a ring plan for that calendar day providing the system
was already in night service. This feature will override the ring plan time table.
4-24
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
Temporary Override
At any time the system can be forced into a specific ring plan for a temporary period of
time until the next scheduled ring plan automatically takes effect.
4.1.1.81 Ring Over Page
Any outside line can be programmed to ring over a customer-provided paging system.
Outside lines, door phones and station groups may ring over page in the system ring plan
mode.
4.1.1.82 Secretary Pooling
Each keyset may be defined as an executive(BOSS in programming) or a secretary(SEC in
programming) in system programming. Each executive can have up to four secretaries and
each secretary can have up to four executives. These arrangements are known as
executive/secretary pools. There can be multiple pools in a system. When an executive is in
DND, all calls to the executive ring the first secretary assigned to that executive; if that
secretary is busy, the call hunt to the next available secretary assigned to that executive.
If the secretary must communicate with the executive while he/she is in DND, pressing the
corresponding executive button on the secretary’s keyset results in an Auto Answer
intercom call being made to the executive(providing the executive is free). The OfficeServ
100 has a system wide option to allow the stations to ring rather than auto announce the
executive secretary calls. A station can only be the executive of one secretary pool.
In addition, a station cannot be in more than one pool.
4.1.1.83 Single Line Connections
Single line ports allow connection of a variety of single line telephones plus facsimile
machines, answering machines, loud bells, computer modems, cordless phones and credit
card machines. When connecting customer-provided equipment to these extensions,
compatibility should be checked out before purchase to ensure correct operation. Central
office ring SVMi-8 can be selected for SLT stations. This is helpful when optional devices
cannot detect OfficeServ 100 intercom ring SVMi-8.
4.1.1.84 Speed Dial Numbers
A library of 1500 speed dial numbers may be allocated as needed for OfficeServ 100.
The system list can have up to 500 numbers(950 numbers when SYSTEM SPEED BIN is
set to MAX950) and each station can have up to 50 numbers. Speed dial numbers are
assigned in blocks of ten. Each speed dial number may contain up to 24 digits.
4.1.1.85 Speed Dial by Directory
The OfficeServ 100 system provides the user with the ability to look up a speed dial
number and place the call. There are three speed dial selections: personal, system and
station. This feature requires a display keyset.
© SAMSUNG Electronics Co., Ltd.
4-25
CHAPTER 4. Business Feature Package
4.1.1.86 Spot View Interface
Spot Call Plus
The caller information is displayed on the LCD screen of the phone and the user’s PC screen.
Spot News
Information from the Internet and internal information are displayed on the LCD screen in
text.
Spot Choice
Information services on stock, fortune, bio-rhythm, etc are displayed upon the user’s choice.
4.1.1.87 Station Hunt Groups
System programming allows up to 20 station hunt groups on an OfficeServ 100. One of three
ring patterns-sequential, distributed and unconditional-is available for each group.
Each unconditional group may contain a maximum of 32 stations and each sequential and
distributed group may contain a maximum of 32 stations. A station may be assigned to more
than one group. Each station group has its own recall timer for calls transferred to that group.
4.1.1.88 SMDR (Station Message Detail Recording)
The system provides records of calls made, received and transferred. Connecting a
customer-provided printer or call accounting system will allow collection of these records.
Each call record provides the following details: station number, outside line number, start
date, start time, duration of call, digits dialed(maximum 18) and an account code if entered.
The system may print a header followed by 50 call records per page or send continuous
records with no header for use with a call accounting machine. See the sample printouts.
The SMDR format contains many options that allow it to be customized for a company’s
individual needs. Options to print include incoming calls, outgoing calls, in and out of
group status, change in DND status and authorization codes.
4.1.1.89 System Alarms
A DISA alarm will warn the customer if the DISA security system has been triggered by
too many incorrect password attempts. The alarm can ring any station or group of stations
and show an appropriate display at the assigned stations.
4.1.1.90 System Maintenance Alarms
The OfficeServ 100 continuously performs internal system diagnostics. When either a
major or minor fault is detected the system can ring stations with an ALARM KEY
assigned. The keyset display shows information that includes the description, location and
date and time stamp for each alarm.
4-26
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
A log of 100 alarms are stored in a buffer and can be reviewed at a display keyset or sent to
a printer(see ‘4.11 Sample Alarm Report’ section of this document).
4.1.1.91 System Directory
Each station, station group and outside line can have an 11 character directory name.
This name will appear on keyset displays to provide additional information about lines and
stations.
4.1.1.92 Text Message Service
When a caller presses the CAMP-ON button on a busy line, the receiving party can press
the TMSG button to send a preset text message to the caller. The Text Message function
shall be enabled on both extensions. Text Messages can be set respectively for each
extension in OfficeServ 100 system.
4.1.1.93 Toll Restriction
There are 250 allow and 250 deny entries of 11 digits each. Each of these entries can apply
to dialing classes B, C, D, E, F and G. Expensive 976, 1-900, 411 and operator-assisted
calls, as well as specific area and office codes, can be allowed or denied on a per-class
basis. Class A stations have no dialing restrictions and Class H stations cannot make
outside calls.
Any outside line may be programmed to follow station toll restriction or follow the toll
restriction class assigned to it. Each station and trunk can have a day dialing class and a
night dialing class.
Special Code Table
A Special Code Table of ten entries(four digits each) allows use of telephone company
features such as CID blocking(*67) or call waiting disable(*70) without interference to toll
restriction or LCR. The Special Code table allows use of these custom calling features on a
per call basis.
4.1.1.94 Toll Restriction Override
Program options allow system speed dial numbers to follow or bypass a station’s toll
restriction class. In addition, users may make calls from a toll restricted station by using the
walking class of service or authorization code feature.
4.1.1.95 Tone or Pulse Dialing
Outside lines can be programmed for either tone or pulse dialing to meet local telephone
company requirements.
© SAMSUNG Electronics Co., Ltd.
4-27
CHAPTER 4. Business Feature Package
4.1.1.96 Traffic Reporting
The OfficeServ 100 system can store peg counts for various types of calls. These peg
counts can be printed on-demand, daily, hourly, or up to three separate programmable shifts.
The report includes statistics for each trunk, trunk group, station, station groups and page
announcements. For more details and explanations see sections ‘4.9 Sample Traffic Report’
and ‘4.10 Traffic Report Overview’ of this document.
4.1.1.97 Transfer
System operation permits station users to transfer calls to other stations in the system.
Transfers can be screened, unscreened or camped-on to a busy station.
4.1.1.98 Trunk Groups
Outside lines can be grouped for easy access by dialing a code or pressing a button.
There are 11 trunk groups available for OfficeServ 100.
4.1.1.99 UCD (Uniform Call Distribution)
UCD is used whenever the user expects to have more ringing calls than people to answer
them. It prevents callers from receiving busy signals or lengthy delays before answering.
Callers reaching a busy station group are held in queue for an available agent. First and
second announcements reassure the caller until an agent becomes free. Programmable
automatic logout removes a station from the group if a call is placed to an unattended
station, thus preventing unanswered calls. A wrap-up timer prevents calls to a station for a
programmable period of time to allow the agent to finish up work associated with the call.
Optional hardware
Requires optional hardware. Ask your dealer for details.
UCD Groups
The UCD group option allows callers in queue at a UCD group to be temporarily diverted
to an announcement device and then placed back in the queue. A wrap-up timer will allow
agents to complete paperwork before receiving the next UCD call.
Call Statistics
UCD supervisor positions using a display keyset can monitor the number of calls in queue,
the time that the oldest caller has been waiting, the total number of calls received for the
current day and the average time a caller waits to be answered.
4-28
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
Agent Statistics
UCD supervisor positions using a display keyset can monitor the number of agents in a
group and how many agents are currently logged in. Each station’s status can be reviewed
for the number of calls answered and the average call length of the current day.
Group Supervisors
Multiple supervisors can be assigned to each group or one station can be given supervisor
status for multiple groups. The group supervisor(using a display keyset) can add and delete
agents in real time from the group to handle the workload.
Printed Reports
Agent supervisors may run printed reports to a customer-provided printer, showing the data
available on the supervisor displays.
4.1.1.100 Universal Answer
Station users may dial the Universal Answer code or press the UA key to answer any
outside lines programmed to ring the UA device. The UA device can be a station, group of
stations, common bell or ring over page.
4.1.1.101 Virtual Port
The OfficeServ 100 provides a Virtual Port. This Virtual Port is not connected to a physical
cable, but has its own phone numbers and functional settings. There are two types of
Virtual Ports, the SLT Line Type and the Digital Line Type. Virtual Port can be used as the
parameter port for call transfer in CTI Applications such as the ICC(Internet Call Center),
and can exchange saved information with real phones using the Set Relocation feature to
implement a Mobile Office. The SLT Line Type Virtual Port and the Digital Line Type
Virtual Port is provided in OfficeServ 100 system.
4.1.1.102 Voice Mail-Inband Integration
The OfficeServ 100 system uses DTMF tones(inband signaling) to communicate with any
compatible voice mail system. Stations can call forward to a voice mail system.
When answered, the system will send DTMF tones routing the caller directly to the called
station user’s mailbox. Keyset users can press one button to retrieve messages from the
voice mail system. A Voice Mail Transfer key permits keyset users to easily transfer a caller
directly to an individual voicemail box without navigating through menus.
© SAMSUNG Electronics Co., Ltd.
4-29
CHAPTER 4. Business Feature Package
4.1.1.103 VoIP Networking
OfficeServ 100 system provides networking through the VoIP Network. The MGI card is
required for calling another system through VoIP Networking. The features provided by
VoIP Networking conform to that of PRI/Q-SIG Networking.
4.1.1.104 VoIP Trunk Interface (H.323/SIP)
The OfficeServ 100 provides VoIP Trunk Interface. The system controls the calls, and a
separate MGI card is required for connection to the speech path.
4.1.1.105 Walking Class of Service
This feature allows users to make calls or use features from a station that is restricted.
The users may either use the WCOS feature code or the authorization code feature.
Both methods change the class of service to correspond with the station passcode or
authorization code that is dialed. After the call is completed, the station returns to its
programmed class of service.
4.1.1.106 Wireless LAN Service
The OfficeServ 100 System, the primary device of SAMSUNG button phone, is mounted
with the 4WLI card that has the wireless LAN function. One 4WLI card can support up to
4 WBS24s, the equipment for AP(Access Point).
In the office where the WBS24 is installed, a user can receive the wireless LAN service
using mobile phone(WIP-5000M), PC and PDA loaded with the wireless LAN card, or
using wireless IP phone.
4-30
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.2 Station Features
ADD-ON MODULE
PROGRAMMABLE KEYS
APPOINTMENT REMINDER
PROGRAMMED STATION MESSAGES
AUTOMATIC HOLD
PROTECTION FROM BARGE-IN
AUTOMATIC PRIVACY
PULLOUT DIRECTORY TRAY
BACKGROUND MUSIC
PULSE TO TONE SWITCH OVER
BUSY STATION CALLBACK
REDIAL
BUSY STATION INDICATIONS(BLF)
AUTO RETRY
CALL FORWARDING
LAST NUMBER
CALL LOGS
MEMO REDIAL
CALL PICKUP
SAVE NUMBER
DIRECT STATION SELECTION(DSS)
REMOTE HOLD
DO NOT DISTURB(OVERRIDE)
RING MODES
DO NOT DISTURB(PROGRAMMABLE)
AUTO ANSWER
DOOR LOCK RELEASE
RING-EIGHT TONE CHOICES
EXCLUSIVE HOLD
VOICE ANNOUNCE
GROUP LISTENING
RINGING PREFERENCE
HEADSET OPERATION
SPEAKERPHONE
HEARING AID COMPATIBLE
STATION LOCK
LINE QUEUING WITH CALLBACK
TRI-COLORED LIGHTS
LINE SKIPPING
VOLUME SETTINGS
LOUD RINGING INTERFACE
HANDSET
MESSAGE WAITING LIGHT/INDICATION
BGM
MUTE MICROPHONE/HANDSET
RINGING
OFF-HOOK RINGING
PAGING
OFF-HOOK VOICE ANNOUNCE(STANDARD)
SPEAKER
OFF-HOOK VOICE ANNOUNCE(EXECUTIVE)
ONE TIME DO NOT DISTURB
OFF-HOOK RING
WALL-MOUNTABLE KEYSETS
ONE TOUCH DIALING KEYS
ON-HOOK DIALING
Optional hardware and software
Requires optional hardware and/or software. Ask your dealer for details.
`
© SAMSUNG Electronics Co., Ltd.
4-31
CHAPTER 4. Business Feature Package
4.2.1 Station Feature Descriptions
4.2.1.1 Add-On Module
32 Button AOM
The 32-button AOM(add-on module) adds to the capability of any keyset.
The 32 programmable buttons with red buttons can be used for feature keys, DSS/BLF
keys or one touch speed dial buttons. Because this AOM has a microphone and a speaker it
can be used to provide executive off hook voice announce or as a stand alone unit
whenever a handset and dial pad are not required.
64 Button Module
The 64-button module adds to the capability of any keyset. Up to four 64-button modules
can be added to each keyset. The 64 programmable red LED buttons with red LED can be
used for feature keys, DSS/BLF keys or one touch speed dial buttons. A maximum of 5 can
be installed on an OfficeServ 100 system.
4.2.1.2 Appointment Reminder
Keysets with an alarm key can be used like an alarm clock. When programmed for a
specific time, the keyset will sound a distinctive ring to remind the user of meetings or
appointments. Alarms can be set for ‘today only’ or for every day at the same time.
Up to three alarms may be set at each keyset. Display keysets can also show a programmed
message when the alarm rings.
4.2.1.3 Automatic Hold
Station users can enable or disable automatic hold at their keysets. While a user is engaged
on an outside(C.O.) call, pressing another trunk key, route key or CALL button
automatically puts the call on hold when this feature is enabled. Pressing TRSF,
CONFERENCE, PAGE or a DSS key will always automatically place the call on hold.
This type of automatic hold is not a user-selectable option.
4.2.1.4 Automatic Privacy
All conversations on outside lines and intercom calls are automatically private. The privacy
feature can be turned off on a per-line basis.
Intercom calls
Intercom calls cannot be automatically held.
4-32
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.2.1.5 Background Music
Keyset users may choose to hear music through their keyset speakers when optional
external sources are installed. Each user may adjust this level by the use of a volume
control program at the selected keyset.
4.2.1.6 Busy Station Callback
When reaching a busy station, callers may request a callback by pressing one button or
dialing a code. The system rings the caller back when that station becomes idle(a systemwide maximum of 100 callbacks are allowed at one time including busy station and busy
trunk).
4.2.1.7 BLF (Busy Station Indications)
DSS/BLF keys may be assigned to any keyset or add-on module. These buttons will be off
when the station is idle, light red when that station is in use and flash distinctively when
that station is in the DND mode.
4.2.1.8 Call Forwarding
Station users can forward internal and outside calls to other destinations immediately
(Forward All), when busy(Forward Busy) or if not answered in a programmable number of
seconds(Forward No Answer). These forward destinations can all be different. Once a
destination has been programmed, it can be turned on and off with a programmable key.
Forward All takes priority over Busy and No Answer conditions.
In addition to the three usual methods of forwarding described above, a fourth option called
Follow Me is available. This option allows a station user to set a Forward All condition
from his/her station to another station while at the remote station. To display the Follow Me
condition, the TRSF key lights steady red at the station that is forwarded. The TRSF key
also lights if Forward All is set and no key is programmed for Forward All.
Keyset users can set the external destination for all kinds of forwarding. Each outside line
may be programmed to either follow or ignore station call forwarding. A per-station option
controls whether internal calls forward to voice mail or not. Single line telephones must
have the system administrator program this feature for them.
4.2.1.9 Call Logs
With the call log feature, a display keyset user can review up to 50 of the last incoming
calls from the Caller ID review list or up to 50 of the last external telephone numbers that
were dialed.
The numbers can be viewed, stored and/or dialed using the associated soft keys. LCR must
be enabled for dialing and storing numbers from the CID review list. Optional hardware
and/or software may be needed for Caller ID.
© SAMSUNG Electronics Co., Ltd.
4-33
CHAPTER 4. Business Feature Package
4.2.1.10 Call Pickup
With directed call pickup, a user can answer calls ringing at any station by dialing a code
plus that extension number. The group pickup feature allows the user to answer any call
ringing within a pickup group. Pickup keys may be customized with extenders to allow
pickup from a specific station or pickup group. The OfficeServ 100 software has 20
programmable pickup groups.
4.2.1.11 DSS (Direct Station Selection)
Programmable keys can be assigned as DSS keys and associated with extension numbers.
Users press these keys to call or transfer calls to the assigned stations.
4.2.1.12 Do Not Disturb (Override)
The DND Override feature allows a keyset with a DNDO(DND Override key) and the
appropriate class of service to override the DND setting at a called keyset. This will allow a
user to go into DND while waiting for an important call and have that call transferred to
them via a screened transfer from a station(for example the users secretary) with a DNDO
key.
4.2.1.13 Do Not Disturb (Programmable)
DND(The Do Not Disturb) feature is used to stop all calls to a station. System
programming can allow or deny use of the DND feature for each station. Parties calling a
station in DND will receive reorder tone. When in DND mode, calls may be forwarded to
another destination. See Forward DND option. A keyset without a DND button can activate
DND via the feature access code. The ANS/RLS key will flash at 112 ipm(rapidly) when
DND is set. There is a programmable option to allow a C.O. line to override DND at its
ring destination if that destination is a single station.
4.2.1.14 Door Lock Release
Stations programmed to receive calls from a door phone can dial a code to activate a
contact closure for control of a customer-provided electronic door lock.
4.2.1.15 Exclusive Hold
Pressing HOLD twice will hold a call exclusively at a station so no other station can pick
up that call. Intercom calls are automatically placed on exclusive hold.
4.2.1.16 Group Listening
This feature allows users to turn on the speaker while using the handset. It allows a group
of people to listen to the distant party over the speaker without the microphone turned on.
4-34
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.2.1.17 Headset Operation
Every keyset can be programmed to allow the use of a headset. In the headset mode, the
hookswitch is disabled and the ANS/RLS key is used to answer and release calls. Keyset
users may turn headset operation ON/OFF by keyset programming or more easily by
pressing the headset ON/OFF key. The headset key lights steady red when the keyset is in
headset mode. The ANS/RLS key lights if headset mode is activated by keyset
programming only.
4.2.1.18 Hearing Aid Compatible
All OfficeServ 100 keysets are hearing aid compatible as required by Part 68 of the FCC
requirements.
4.2.1.19 Line Queuing with Callback
When the desired outside line is busy, the user can press the CALLBACK key or dial the
access code to place his/her station in a queue. The user will be called back when the line is
available(a maximum of 100 callbacks are allowed system-wide at one time including busy
station and busy trunk).
4.2.1.20 Line Skipping
When the user is talking on an outside line and the automatic hold feature is turned off,
he/she may press an idle line key and skip to that line without causing the previous call to
go on hold.
4.2.1.21 Loud Ringing Interface
The MISC board has 3 relays that can be programmed to provide a dry contact closure for
control of a customer provided loud ringing device. Any of these relays can be
programmed to operate with a specific station or station group.
4.2.1.22 Manual Signaling
Phones can signal each other via a programmable button. This allows one station to alert
another without establishing a voice conversation. Each press of the button results in a 500
milliseconds of ring tone being set to the intended station. An individual manual signaling
button must be programmed for each station to be signaled.
4.2.1.23 Message Waiting Light/Indication
When a message indication is left at a keyset, the MESSAGE button will slowly flash red.
Single line telephones will receive a distinctive dial tone to notify them that a message is
waiting. Message waiting indications can be left for any station or group of stations.
© SAMSUNG Electronics Co., Ltd.
4-35
CHAPTER 4. Business Feature Package
4.2.1.24 Mute MicroPhone/Handset
Any keyset user can mute the keyset’s handset transmitter by pressing the MUTE key.
In addition, keyset users can also mute the keyset microphone while the keyset is in
speakerphone mode.
4.2.1.25 Off-Hook Ringing
When a keyset is in use, the system will provide an off-hook ring signal to indicate that
another call is waiting. The ring signal is a single ring repeated. The interval is controlled
by a system-wide timer. Single line stations will receive a tone burst through the handset
receiver instead of a ring.
4.2.1.26 Off-Hook Voice Announce (Executive)
A keyset associated with an add-on module may receive an executive off-hook voic
e announcement while on another call. The called keyset user may reply handsfree without
interrupting the call in progress. Only keysets with an button OHVA(off-hook voice
announce) can off-hook voice announce to keysets with AOMs.
4.2.1.27 Off-Hook Voice Announce (Standard)
Keysets may receive a voice announcement while on another call. The calling station must
have an OHVA key. When transferring a call to a busy keyset or while listening to busy
signal, the station user can press the OHVA key to make an OHVA call to the busy keyset.
If the called keyset is in the DND mode, it cannot receive OHVA calls.
4.2.1.28 One Time Do Not Disturb
The Do Not Disturb(One Time) feature is used to stop all calls to a station when the user is
on an outside line and does not want to be disturbed for the duration of the call.
Upon completion of the call, DND is canceled and the station is returned to normal service.
This feature requires a programmed button.
4.2.1.29 One Touch Dialing Keys
Frequently used speed numbers can be assigned to one touch dialing keys for fast accurate
dialing.
4.2.1.30 On-Hook Dialing
Any keyset user can originate calls without lifting the handset. When the called party
answers, the user may speak into the microphone or lift the handset for more privacy.
4-36
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.2.1.31 Programmable Keys
LCD 24B and STD 24B keysets have 24 programmable keys, LCD 12B and Basic 12B
keysets have 12, and 7B keysets have 12. Each key can be programmed for more than 25
different uses to personalize each phone. Examples of keys include individual outside line,
individual station, group of lines, group of stations and one touch speed dial buttons.
Using these keys eliminates dialing access codes.
The following feature keys have extenders that make them more specific: SPEED DIAL,
SUPERVISOR, PAGE, DSS, DIRECTED PICKUP, GROUP PICKUP, DOOR PHONE,
BOSS, PROGRAMMED MESSAGE, IN AND OUT OF GROUP, FORWARD and VOICE
MAIL TRANSFER. The extender can be a station, a group or another identifying number.
4.2.1.32 Programmed Station Messages
Any station may select one of 20 to be displayed at a calling party’s keyset. Ten messages
are factory-programmed but may be reprogrammed. On OfficeServ 100 software last five
messages can be programmable per station basis.
Calling party
The calling party must have a display keyset to view these messages.
4.2.1.33 Protection from Barge-In
Each station can be programmed as secure or not secure. Secure stations cannot be bargedin on. A station that is not secure cannot be barged-in on when talking to a secure station.
4.2.1.34 Pullout Directory Tray
A pullout directory tray is conveniently located beneath all keysets. It is used to record
station directory names and speed dial numbers.
4.2.1.35 Pulse to Tone Switchover
When dialing a number on a dial pulse network, a station user can dial # and the OfficeServ
system will begin to send DTMF.
4.2.1.36 Redial
There are three types of external redial available to all station users. Each type can redial
up to a maximum of 18 digits.
Auto Retry - When an outside number is dialed and a busy signal is received, the auto
retry feature can be used to reserve the outside line and automatically redial the
number for a programmable number of attempts(available to keyset users only)
© SAMSUNG Electronics Co., Ltd.
4-37
CHAPTER 4. Business Feature Package
Last Number - The most recently dialed number on a C.O. line is saved and may be
redialed by pressing the redial key or dialing the LNR access code.
Manual Retry with LNR - When you make an outside call and receive a busy signal
you can press the LNR key to redial the same number again. This operation can be
manually repeated for a limited number of attempts as defined by system
programming(available to keyset users only).
Memo Redial - When you are calling directory assistance you can store the number
you are given using the dial pad and SAVE number feature. There is no need for a
pencil and paper(available to phone users only).
Save Number - Any number dialed on a C.O. line may be saved for redial at a later
time.
4.2.1.37 Remote Hold
When you wish to place a call on hold at another station, press TRSF and dial the station
number(or press the appropriate DSS key). Press the HOLD key. This will place the call on
system hold on an available CALL button or Line Key at the remote station.
4.2.1.38 Ring Modes
Each keyset user can select one of three distinct ways to receive intercom calls. The phone
can automatically answer on the speakerphone, voice announce through the speaker or
receive ringing. When the ring mode is selected, keyset users can choose one of eight
distinct ring tones. Forced Auto Answer is invoked by the calling station and is controlled
by the calling station’s class of service.
4.2.1.39 Ringing Preference
Lifting the handset or pressing the speaker button automatically answers a call ringing at
the keyset. Using this method, users are assured of answering the oldest call first.
When ringing preference is turned off, the user must press the flashing button to answer.
Users may answer ringing lines in any order by pressing the flashing button.
4.2.1.40 Speakerphone
DCS LCD 24B and DCS LCD 12B keysets have built-in speakerphone. The speakerphone
enables calls to be made and received without the use of the handset. All iDCS keysets are
speakerphones. The iDCS 28 Button and the iDCS 18 Button can have a Full Duplex
Speakerphone Module added.
4.2.1.41 Station Lock
With a programmable personal station passcode, any keyset or single line station can be locked
and unlocked to control use of each telephone. There are two lock options: 1=LOCKED
OUTGOING and 2=LOCKED ALL CALLS. See the following table for more details.
4-38
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.2.1.42 Tri-Colored Lights
LCD 24B and STD 24B keysets have 16 keys equipped for tri-colored LED
indications(green, red and amber). LCD 12B and Basic 12B models have six of these keys
and 7 button keysets have three. To avoid confusion, your calls always light green, other
calls show red and recalls light amber.
4.2.1.43 Volume Settings
Each keyset user may separately adjust the volume of the ringer, speaker, handset receiver,
background music, page announcement and off-hook ring tone.
4.2.1.44 Wall-Mountable Keysets
Each keyset, add on module and 64 button module can be wall mounted by reversing the
base wedge. The newest base wedge may not fit all wall mounting scenarios so in these
cases the original wall mount/base wedge unit should be used.
© SAMSUNG Electronics Co., Ltd.
4-39
CHAPTER 4. Business Feature Package
4.3 Display Features
ACCOUNT CODE DISPLAY
ENHANCED STATION PROGRAMMING
CALL DURATION TIMER
IDENTIFICATION OF RECALLS
CALL FOR GROUP IDENTIFICATION
IDENTIFICATION OF TRANSFERS
CALL PROCESSING INFORMATION
MESSAGE WAITING CALLER NUMBER
CALLER ID INFORMATION
OUTSIDE LINE IDENTIFICATION
CALLING PARTY NAME
OVERRIDE IDENTIFICATION
CALLING PARTY NUMBER
PROGRAMMED MESSAGE DISPLAY
CONFERENCE INFORMATION
SOFT KEYS
DATE AND TIME DISPLAY
STOPWATCH TIMER
DIALED BY NAME
DIALED NUMBER
UCD SUPERVISOR DISPLAYS
4.3.1 Display Feature Descriptions
4.3.1.1 Account Code Display
Account codes are conveniently displayed for easy confirmation. If entered incorrectly,
users may press the ACCOUNT key again and reenter the account code.
4.3.1.2 Call Duration Timer
The system can automatically time outside calls and show the duration in minutes and
seconds. Station users may manually time calls by pressing the TIMER button.
4.3.1.3 Call for Group Identification
When a call is made to a station group, the display shows [CALL FOR GROUP] and the
user’s group number. These calls can be answered with a different greeting than calls to the
user’s extension number.
4.3.1.4 Call Processing Information
During everyday call handling, the keyset display will provide information that is helpful
and in some cases invaluable. Displays such as [CALL FROM 203], [TRANSFER TO 202],
[701: RINGING], [TRANSFER FM 203], [708 busy], [Camp on to 204], [Recall from 204],
[Call for 501], [message from 204] and [FWD ALL to 204] keep users informed of what is
happening and where they are. In some conditions, the user is prompted to take action and
in other cases the user receives directory information.
4.3.1.5 Caller ID Information
Caller ID information is dependent on the use of display keysets. The following list
explains the displays that are used with Caller ID.
4-40
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
Name/Number Display
Each display keyset user can decide if he/she wants to see the Caller ID name or Caller ID
number in the display. Regardless of which one is selected to be seen first, the NND key is
pressed to view the other piece of CLIP information.
Next Call
In the event that there is a call waiting or a camped-on call at the user’s keyset, the user can
press the NEXT key to display the Caller ID information associated with the next call in
queue at the station. Either the CLIP name or CLIP number will show in the display
depending on the N/N selection.
Save Clip Number
At any time during an incoming call that provides CLIP information, the user may press the
SAVE key. This saves the CLIP number in the Save Number feature. Pressing the SAVE
number redial key will dial the CLIP number. The system must be using LCR to dial the
saved number.
Store Clip/ANI number
At any time during an incoming call that provides CLIP information, the user may press the
STORE key. This saves the CLIP number as a speed dial number in the personal speed dial
list. The system must be using LCR to dial the stored number.
Inquire Park/Hold
When a user is informed that an incoming call is on hold or has been parked, the user may
view the Caller ID or ANI information before he/she retrieves the call. This will influence
how the user chooses to handle the call.
Clip Review List
This feature allows display keyset users to review CLIP information for calls sent to their
stations. This list can be from ten to fifty calls in a first in, first out basis. The list includes
calls that were answered and calls that rang the user’s station but that were not answered.
When reviewing this list, the user can press one button to dial the person back. The system
must be using LCR to dial the stored number.
Investigate
This feature allows selected stations with a special class of service to investigate any call in
progress. If CLIP information is available for an incoming call, the selected stations can
know to whom the OfficeServ 100 user is speaking. On outgoing calls, the selected stations
can see who was called. After investigating, the selected stations may barge-in on the
conversation, disconnect the call or hang up.
© SAMSUNG Electronics Co., Ltd.
4-41
CHAPTER 4. Business Feature Package
Abandon Call List (50)
The system has a system-wide abandon call list that stores CLIP information for calls that
rang but were not answered. The list is accessed using the operator’s passcode.
When reviewing this list, you are provided options to CLEAR the entry or DIAL the
number. You can use the NND key to toggle between the CLIP name, CLIP number and the
date and time the call came in. The system must be using LCR to dial numbers from the
abandon call list. The abandoned call list will store up to 50.
4.3.1.6 Calling Party Name
For intercom calls, LCD 24B and LCD 12B keysets show the calling party’s name before
answering. The names must be stored in the system directory list and can be up to 11
characters long.
4.3.1.7 Calling Party Number
When an intercom call is received, all display stations show the calling party’s extension
number before the call is answered.
4.3.1.8 Conference Information
When a conference is set up, each extension and outside line number is displayed at the
controlling station when it is added. When a station is added, its display shows [Conf with
xxx] alerting the user that other parties are on the line.
4.3.1.9 Date and Time Display
In the idle condition, the current date and time are conveniently displayed. Display keysets
can have a 12 or 24 hour clock in either the ORIENTAL or WESTERN display format with
information shown in upper case or lower case letters.
4.3.1.10 Dial by Name
Each station and speed dial number can have an associated directory name. Any station or
speed dial number can be selected by scrolling alphabetically through a directory list.
There are three directories:
System wide speed dial list
Personal speed dial list
Station directory list
This online ‘phone book’ allows display keyset users to look up and dial any speed dial
number or station in seconds.
4-42
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.3.1.11 Dialed Number
When an outside call is made, digits are displayed as the user dials them. If the display
indicates an incorrect number was dialed, the user can quickly hang up before billing
begins.
4.3.1.12 Enhanced Station Programming
Personal programming options are easier to select and confirm with the help of the display.
4.3.1.13 Identification of Recalls
Hold recalls and transfer recalls are identified differently than other ringing calls.
Hold recalls indicate the recalling line or station number and the associated name.
Transfer recalls indicate the recalling line or station and where it is coming from.
4.3.1.14 Identification of Transfers
The display will identify who transferred a call to the user.
4.3.1.15 Message Waiting Caller Number
When the message indication is on, pressing the MESSAGE button displays the station
number(s) of the person(s) who have messages for the user. Display keyset users can scroll
up and down to view message indications.
4.3.1.16 Outside Line Identification
Each line can be identified with an 11 character name. Incoming calls display this name
before the call is answered. This feature is helpful when individual lines must be answered
with different greetings.
4.3.1.17 Override Identification
If another station barges-in on a user’s conversation, the display will alert the user with a
[Barge from 2xx] display if the system is set for barge-in with tone.
4.3.1.18 Programmed Message Display
Preprogrammed station messages set by other stations are displayed at the calling station’s
keyset.
4.3.1.19 Soft Keys
Below the display, there are three soft keys and a SCROLL button. These keys allow the
user to access features in his/her class of service without requiring the keyset to have
designated feature keys.
© SAMSUNG Electronics Co., Ltd.
4-43
CHAPTER 4. Business Feature Package
4.3.1.20 Stopwatch Timer
Display keyset users find this feature very convenient to time meetings, calls and other
functions. Users simply press once to start the timer and press again to stop the timer.
4.3.1.21 Text Messaging
This feature allows two display phone users to respond to each other with preprogrammed
messages.
After receiving an Off Hook Voice Announcement or Station Camp-On, you may respond
with a text message while continuing to talk and listen to your outside party. The other
station can view this message and take the appropriate action or respond back with another
text message.
In OfficeServ 100 system , there are additional Text Messages per station basis. Only the
display phones that are allowed in system programming will receive the TMSG soft button
in the display and can use this feature.
4.3.1.22 UCD Supervisor Displays
With the optional AA card, when UCD is used, multiple supervisors can view information
about the UCD groups calls or agents.
Call Screen
This allows the supervisor to view how many calls are in queue, the longest wait time, how
many calls have been received today, what the average time in queue is and how many
calls were abandoned.
Agent Screen
This allows the supervisor to monitor how many agents are logged in, check each agents
status(IN GROUP, OUT OF GROUP, or DND), view each agents total number of calls,
average call length or average ring time.
Supervisor display
Accessing this screen will also allow a Supervisor to change the status of each
agent(IN GROUP, OUT OF GROUP, or DND).
4-44
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.3.2 Sample Displays
PROSTAR LCD 12B and LCD 24B display model keysets have a large, easy-to-read, 32
character liquid crystal display. Helpful call processing information is provided so
everyday call handling is quick and easy. Here are just some of the displays you may see.
209: Tim Kelly
RRI 23 Sep
Idle display shows extension, name,
day, date and time.
Call for 501
202 Mr. Smith
This station in the sales department is
receiving a group call from Mr. Smith.
203: Busy
CBK MSG CAMP
This station is calling station 203 which
is currently busy.
Conf with 203
John
This station is on a conference call with
John, extension 203. Assume other
parties will hear your conversation.
Transfer to 203
John
This station is transferring a call to John
at extension 203.
DO NOT DISTURB
ON
OFF
This station is setting the Do Not
Disturb feature.
© SAMSUNG Electronics Co., Ltd.
Camp on to 203
Wait for answer
This station is camped-on to extension
203 and is waiting for 203 to answer.
Call for 501
706 Local #6
This display tells you this is a new
incoming call to the sales department.
OHVA from 203
REJECT
This station is receiving an off-hook
voice announcement from station 203.
CONF: 202 702
CONF
This station is on a conference call with
extension 202 and trunk 702 and has
the option to add two more parties.
Call from 201
Operator
This station is receiving a call from
extension 201.
703 Local 3
CONF PAGE MUTE
This station is receiving a call from
extension 201.
4-45
CHAPTER 4. Business Feature Package
4.3.3 Sample Caller ID Displays
13054264100
702: RINGING
This display shows an incoming call
from 1-305-426-4100 on Line 702
ringing directly at your station.
13054264100
TRANSFER FM 201
This display shows an incoming call
from 1-305-426-4100 on Line 702
ringing directly at your station.
SAMSUNG TELECOM
BARGE NND DROP
This display shows an investigation
of a station that is talking to
Samsung Telecom. Investigator
can BARGE-in to the conversation,
DROP the call from the system of
examine further NND information.
SAMSUNG TELECOM
CALL FOR: 500
This display shows an incoming call
from Samsung Telecom ringing at
group 500.
05/25, 09: 41, 702
CLEAR NND
This display shows the information on the
abandoned call list. This call came in on
May 25 at 9:41 A.M on line 702. The user
can CLEAR the entry. DIAL the caller
back or examine further NND information.
SAMSUNG TELECOM
CLEAR NND
This display shows an entry in a station
review list showing the three initial options.
The arrow indicates other options available
to you by pressing the SCROLL key.
13054264100
NEXT NND ANS
This display is seen while examining
calls in oueue at your keyset.
TALKING TO: 203
BARGE
DROP
This display can be seen when
investigating an intercom call.
The investigator can BARGE-in or
DROP the connection.
SAMSUNG TELECOM
ANS NND IGNORE
This display is seen while using the
INQUIRE feature. It shows the three
options available while you are
checking on a held or parked call.
4-46
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.3.4 Sample UCD Displays
005 calls in
queue now
There are five calls currently waiting
to be answered by the UCD group.
longest wait
time is 02:24
The longest call on hold(waiting to be
answered) was for two minutes, 24
seconds. This data applies to all calls
since the supervisor data was last
cleared. It does not necessarily
represent calls currently in queue.
124 calls
received today
The UCD group has received 124
calls today.
average time in
queue is 03:51
The average time on hold(waiting to
be answered) is three minutes and
51 seconds.
© SAMSUNG Electronics Co., Ltd.
06 available
04 logged in
There are six members in the group. Fou r
of the members are currently logged in.
201: answered
065 calls today
The agent at station 201 has answered
65 calls today.
201: average
call time 04:43
The average call length for station
201 is four minutes and 43 seconds.
202: Sondra
STATUS: OUT
Station 202 is currently out of the
group.(The display can also show IN
GROUP and DND.)
4-47
CHAPTER 4. Business Feature Package
4.4 Sample SMDR Printout (Without Caller ID)
1
1
T
210
202
226
208
EXT
702
704
703
703
705
TRK
09/23
09/23
09/23
09/23
09/23
MM/DD
16:15:51
16:15:28
16:14:00
16:13:31
16:12:33
STT.TIME
00:01:45
00:01:52
00:00:25
00:00:29
00:05:12
DURATION
I
O
TT
IT
OT
FG
12145551234567
DIALED DIGIT
SMDR REPORT FOR [Samsung R & D] 09/23/94 17:30
1
201
AUTH
1
4205068
4205069
1
09/23
09/23
16:18:16
16:19:53
00:01:57
00:00:25
O
T
211
703
204
735
735
09/23
09/23
09/23
09/23
17:25:15
17:18:08
17:17:38
17:17:15
00:00:28
00:12:19
00:00:30
00:00:11
FI
DO
DI
DE
4205071
18005551234
709
FO
O
209
701
00:10:25
706
703
1
00:02:43
DND ON
5555
1
16:20:59
DND OFF
ALARM RINGING
17:04:10
GROUP OUT
IT
208
09/23
17:12:07
GROUP IN
00:00:19
210
09/23
17:12:05
00:04:15
1
211
09/23
17:16:55
16:21:12
1
208
09/23
16:21:31
1
208
09/23
09/23
1
207
09/23
1
207
702
1
1
735
17:25:15
13054264100
3833
1
706
09/23
O
1
1
706
00:08:12
13055551234
1
701
18:00:03
1
09/23
2326
705
312
Time Call Made or
Extension
Call Type Flag
C.O. Line
Received Hrs:Mins:Secs
2-4Digit
2
Characters
No.
Telephone No.
Call Duration
Authorization Data Call Made or
Dialed 1-18 Digits
Hrs:Mins:Secs
Received
Code
Month:Day
4 Digit
1
Tenant
1 Digit
ACCOUNT CODE
1234567890*#
987654321012
232552779600
Account
Code 1-12
Digits
DISA call with error
Transferred call that was
terminated
Incoming transfer
Incoming call forwarded
to an external number
Outgoing transferOutgoing call made and
transferred
Caller received a
transferred call and
transferred it again
Outgoing
Incoming Call
DISA call in
DISA call out
Outgoing record of
forwarded call
Call Type Flag Definitions
DE
T
IT
FI
OT
TT
O
I
DI
DO
FO
© SAMSUNG Electronics Co., Ltd.
4-48
OfficeServ 100 General Description Guide/Ed.00
4.5 Sample SMDR Printout (With Caller ID)
SMDR REPORT FOR [Samsung R & D] 09/23/94 17:30
1 202
1 202
1 247
1 205
1 201
702
702
702
702
702
701
701
T EXT AUTH TRK
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
MM/DD
17:28:04 00:00:00
17:27:13 00:00:20
17:26:46 00:00:16
17:26:35 00:00:11
17:25:56 00:00:00
17:25:14 00:00:03
17:24:49 00:00:25
17:15:41 00:00:02
17:15:13 00:00:28
STT.TIME DURATION
O
O
T
IT
O
T
IT
T
IT
FG
4264385
4264385
13055559748
13054264385
13054264385
13055552354
13055557890
13054264100
13054264100
LENNY WILKINS
JOAN LEVIN
SAMSUNG TELECOM
SAMSUNG TELECOM
SUSAN HOLLINS
CURTIS SMITH
SAMSUNG TELECOM
SAMSUNG TELECOM
CID/ANI NAME
DE
T
Call Type Flag Definitions
CID/ANI NUMBER
1 217
702
IT
13055558703
PIZZA DELIVERY
4264100
5556420
ACCOUNT CODE
1 203
702
17:28:34 00:00:04
T
13055556420
DIGIT
1 203
01/02
OT
DIALED
1 203
701
17:28:38 00:00:14
TT
O
I
DI
DO
FO
TT
OT
IT
FI
1 201
01/02
17:29:54 00:00:00
5555069
DISA call with error
Transferred call that was
terminated
Incoming transfer
Incoming call forwarded
to an external number
Outgoing transferOutgoing call made and
transferred
Caller received a
transferred call and
transferred it again
Outgoing
Incoming Call
DISA call in
DISA call out
Outgoing record of
forwarded call
701
17:31:06 00:03:00
1 203
01/02
702
01/02
702
PIZZA DELIVERY
1 203
TERRY PRUITT
1 205
13055556420
01/02
13055553426
01/02
O
T
702
17:42:15 00:00:02
A
A
701
17:51:17 00:00:22
17:33:24 00:02:18
1 209
01/02
17:56:02 00:00:05
17:41:45 00:00:30
1
01/03
BLANCHE MARKER
701
01/03
13055554676
702
A
1
701
A
ALEX DAULTON
1 203
17:56:07 00:00:54
Caller ID/ANI Name
1-15 Characters
13055556733
1
01/03
Caller ID/ANI
Number 1-15 Digits
CHAZ NEWMAN
701
Account Code
1-12 Digits
13055559723
1
Call Type Flag
Time Call Made or
Extension C.O. Line No.
2 Characters
Received Hrs:Mins:Secs
2-4Digit
2-4Digit
Telephone No.
Call Duration
Authorization Data Call Made or
Code 4 Digit Received Month:Day Hrs:Mins:Secs Dialed 1-18 Digits
Tenant
1 Digit
4-49
© SAMSUNG Electronics Co., Ltd.
CHAPTER 4. Business Feature Package
4.6 Sample UCD Report
UCD GROUP 529 : SALES
FROM: SUN 02 Feb 00:00
TO : SUN 02 Feb 02:54
CALL STATISTICS
===============
AVERAGE RING TIME(TIME TO ANSWER)......
NUMBER OF TIMES ALL AGENTS BUSY........
AVERAGE TIME IN QUEUE..................
TOTAL CALLS RECEIVED...................
LONGEST QUEUE TIME(TODAY)..............
TOTAL CALLS ABANDONED..................
00:40
00002
00:51
00011
02:14
00004
AGENT STATISTICS
================
MEMBER AGENT
NAME
CALLS
AVERAGE RING
ANSWERED
CALL TIME
TIME
--------------------------------------------------------------------01
210
JOHN
0002
01:55
00:05
02
211
SAM
0001
02:18
00:06
03
208
MIKE
0003
01:22
00:04
04
207
PETER
0001
03:16
00:05
======================================================================
UCD GROUP 515 : SUPPORT
FROM: MON 03 Jan 08:30
TO : SUN 02 Jan 02:54
CALL STATISTICS
===============
AVERAGE RING TIME(TIME TO ANSWER)......
NUMBER OF TIMES ALL AGENTS BUSY........
AVERAGE TIME IN QUEUE..................
TOTAL CALLS RECEIVED...................
LONGEST QUEUE TIME(TODAY)..............
TOTAL CALLS ABANDONED..................
00:07
00005
01:06
00023
01:02
00001
AGENT STATISTICS
================
MEMBER AGENT
NAME
CALLS
AVERAGE RING
ANSWERED
CALL TIME
TIME
-----------------------------------------------------------------01
223
FRED
0012
02:33
00:08
02
213
JANE
0010
01:04
00:04
4-50
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.7 UCD Call Statistics
4.7.1 Calls in Queue Now
How many calls are currently in queue.
This statistic is a real time statistic and so will not print on a report.
4.7.2 Abandoned Calls
This shows the number of callers that reached the UCD group, but hung up before being
answered. A high number probably means that there are not enough agents available and
the wait time is too long.
4.7.3 Average Ring Time
This is calculated from the time an agent begins to ring until the time an agent answers the
call, this does not include ringing at an agent station that does not answer or is logged out
because of the ring next option.
4.7.4 Number of Times All Agents Busy
This is the number of times that a call is placed to an UCD group and all agents are busy or
out of group. This check is made when the call is first placed to the group.
Example: If there are 5 members in a group, 3 are Out of Group one is busy and one is idle,
and a call is placed to the group, because there is an idle station the all agents busy counter
is not incremented.
If the idle station rings, does not answer and is logged out, although the condition of the
group is now all agents busy, the check has been made and the agent busy statistic does not
increment.
Also if a call comes into a group with all agents busy and then one becomes idle, the busy
counter will increment because the check has been made.
4.7.5 Average Time in Queue
This is calculated as an average of all the calls that were in queue.
Note that this is ONLY an average of the calls that were in queue.
The caller must have overflowed to the UCD recording to be considered in queue.
A call is considered in queue until it is answered or until it goes to the final destination.
© SAMSUNG Electronics Co., Ltd.
4-51
CHAPTER 4. Business Feature Package
4.7.6 Total Calls Received
The total number of times that calls were sent to a group. This includes calls that were
answered by the group, calls that went to a group with all agents busy or out of group, calls
that are abandoned and calls that go to UCD final destination. This includes intercom calls
to the UCD group.
If this number is less than the total calls received by all the agents it is possible that calls
were transferred from one agent to another.
If this number is more than the total calls received by all the agents it is possible that calls
were unanswered by an agent and went to final destination or callers hung up while in
queue.
This statistic includes:
Calls answered by agent.
Calls that are not answered by an agent and go to final destination.
Calls that are sent to the UCD group but callers hang up before being answered.
4.7.7 Longest Queue Time Today
This shows the longest call in queue today. The queue time is calculated as follows:
Queue time begins when a caller starts to hear the first UCD message.
Queue time ends when a caller is either
− Answered by an agent
− System gets disconnected from C.O. or
− Caller is transferred to final destination
4.7.8 Longest Queue Time Now
This shows the longest call currently in queue. The queue time is calculated as follows:
Queue time begins when a caller starts to hear the first UCD message.
Queue time ends when a caller is either
− Answered by an agent
− System gets disconnected from C.O. or
− Caller is transferred to final destination
4-52
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.8 UCD Agent Statistics
4.8.1 Logged In
The number of stations programmed in the UCD group and the number of stations that are
currently logged in. This statistic is a real time statistic and so will not print on a report.
4.8.2 Status
This screen shows the agents name, extension number and status. The status can be In
Group, Out of group or in DND.
This statistic is a real time statistic and so will not print on a report.
4.8.3 Calls Answered
The total number of calls answered by the agent. This does not include ring no answer to an
agent station.
If this total number is less than the calls received by the group it is possible that calls were
unanswered by an agent and went to final destination or that callers hung up while in queue.
If this total number is more than the calls received by the group it is possible that calls were
transferred from one agent to another.
4.8.4 Average Call Time
This is an average of all the call durations for the agent.
4.8.5 Average Ring Time
This is an average of all the ring times for the agent. Ring times are previously explained.
© SAMSUNG Electronics Co., Ltd.
4-53
CHAPTER 4. Business Feature Package
4.9 Sample Traffic Report
TRAFFIC REPORT FOR [ SAMSUNG ] Mar/21/1999 13:35
************************* SYSTEM STATISTICS *************************
BEGINNING:
Mar/15/1999
00:42
ENDING: Mar/21/1999 13:32
ACTIVITY
SYSTEM TOTAL
INCOMING TRUNK CALLS - ANSWERED..................
3041
INCOMING TRUNK CALLS - NOT ANSWERED..............
26
OUTGOING TRUNK CALLS ............................
2168
A SELECTED TRUNK WAS BUSY........................
44
INTERCOM CALLS – COMPLETED .......................
7178
INTERCOM CALLS - NOT ANSWERED ....................
1540
TRUNK RECALLS TO STATION .........................
145
TRUNK RECALLS TO OPERATOR GROUP ..................
32
INTERNAL PAGE USED ...............................
35
EXTERNAL PAGE USED ...............................
79
ALL PAGE USED ....................................
231
************************* TRUNK GROUPS *************************
GROUP
OUTGOING
9
1245
18
800
521
3
801
20
3
802
0
0
BUSY
************************* INDIVIDUAL TRUNKS *************************
TRUNK
TRUNK-NAME
ATTA
ANSD
NOT-ANSD
OUTGOING
BUSY
701
LOCAL 1
0
737
0
19
12
702
LOCAL 2
0
541
4
26
11
703
LOCAL 3
0
290
1
37
21
************************ STATION HUNT GROUPS ************************
<———————— OUTSIDE CALL ————————>
GROUP
<-INTERCOM->
ANSD
NOT-ANSD
500
439
19
ANSD
501
261
37
38
502
40
2
77
503
87
5
162
504
19
1
44
61
************************ INDIVIDUAL STATIONS ************************
<—————— OUTSIDE CALL —————————————————————————————><-INTERCOM——>
EXT STATION-NAME ATTA ANSD NOT-ANSD DIALED ICM–TRSF TRK-TRK PICKUP ANSD DIALED
201 Operator
202 Barbara
203 Ivania
4-54
11
15
341
0
0
39
72
12
9
60
360
2
80
20
0
12
49
66
4
25
1
36
3
0
18
86
29
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.10 Traffic Report Overview
A************************* SYSTEM STATISTICS ************************
1 BEGINNING: Mar/15/2001 08:00
ENDING: Mar/15/2001 17:30
2 ACTIVITY SYSTEM TOTAL
3
4
5
6
INCOMING TRUNK CALLS
INCOMING TRUNK CALLS
OUTGOING TRUNK CALLS
A SELECTED TRUNK WAS
- ANSWERED..................0000
- NOT ANSWERED..............0000
............................0000
BUSY........................0000
7 INTERCOM CALLS - COMPLETED.......................0000
8 INTERCOM CALLS - NOT ANSWERED....................0000
9 TRUNK RECALLS TO STATION.........................0000
10 TRUNK RECALLS TO OPERATOR GROUP.................0000
11 INTERNAL PAGE USED..............................0000
12 EXTERNAL PAGE USED..............................0000
13 ALL PAGE USED...................................0000
4.10.1 Beginning & Ending
This identifies when the statistics were collected. It includes dates and time.
4.10.2 Activity
Overall summary of traffic in the system for activities 3 to 13.
4.10.3 Incoming Trunk Calls-Answered
These are any incoming trunk calls to the system. These calls are pegged when answered
by any device and/or station in the system whether it is a new call or a recall.
4.10.4 Incoming Trunk Calls-Not Answered
These are any incoming trunk calls that were not answered by any station or device in the
systems. These are the same calls that would be flagged as abandoned in SMDR.
4.10.5 Outgoing Trunk Calls
These are all outgoing trunk calls that were originated by any station or through the DISA
feature. Outgoing trunk calls are valid calls as defined by the SMDR START TIME in
MMC 501.
© SAMSUNG Electronics Co., Ltd.
4-55
CHAPTER 4. Business Feature Package
4.10.6 A Selected Trunk Was Busy
Pegged every time a trunk or trunk group was busy regardless of the manner in which it
was selected(e.g., DTS key, LCR, ‘9’, 7XX, TRK GROUP SELECT, SPD, External call
forward, DISA).
4.10.7 Intercom Calls Completed
These are all intercom calls that were completed to any station, station group or device.
4.10.8 Intercom Calls Not Completed
These are all intercom calls that were not answered and resulted in the calling party
hanging up. A call to a station group that overflows to another station is considered not
answered whether the overflow destination did or did not answer.
4.10.9 Trunk Recalls to Station
These are trunk calls that were placed on any kind of hold and recalled a station. These are
also trunk calls that were transferred and were not answered and recalled the transferring
station. This includes members of the operator group that put calls on hold and then recall
the operators station.
4.10.10 Trunk Recalls to Operator Group
These are any trunk calls that recalled to the operator group.
4.10.11 Internal Page Used
Peg count of every time internal page was accessed.
4.10.12 External Page Used
Peg count for every time external page was accessed.
4.10.13 All Page Used
Peg count of every time the all page feature was accessed. This does not include internal or
external page, only 55+ * or PAGE *.
B**************************** TRUNK GROUPS **************************
1 GROUP
9
800
801
4-56
2 OUTGOING
0000
0000
0000
3 BUSY
0000
0000
0000
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.10.14 Group
A listing of all trunk groups assigned in the system.
4.10.15 Outgoing
These are the number of outgoing trunk calls made using each trunk group. Pegged every
time a member of this trunk group was used to make a valid outgoing call. A valid outgoing
call is defined by the SMDR Start Time programmed in MMC 501.
4.10.16 Busy
This is the number of times each trunk group was busy when someone attempts to access it.
C************************** INDIVIDUAL TRUNKS ************************
1TRUNK
701
702
703
704
705
706
707
708
709
710
2TRUNK-NAME
3ATTA
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
4ANSD
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
5NOT-ANSD
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
6OUTGOING
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
7BUSY
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
4.10.17 Trunk
A listing of each trunk in the system.
4.10.18 Trunk Name
The names of each trunk as programmed in MMC 404.
4.10.19 ATTA
Average Time To Answer for trunks is counted in the number of seconds that ringing
voltage is detected at the trunk interface and the timer stops when trunk is answered by
station or device in the system. The ATTA is the sum of all answered times divided by the
answered call count.
4.10.20 ANSD
This is the number of times this specific trunk was answered by any station or device
whether it is a new call or a recall.
© SAMSUNG Electronics Co., Ltd.
4-57
CHAPTER 4. Business Feature Package
4.10.21 Not-ANSD
This is the number of times this specific trunk rang the system but was not answered.
These are the same calls that would be flagged as abandoned in SMDR.
4.10.22 Outgoing
This is the number of times this trunk was used to make an outgoing call. A valid outgoing
call is defined by the SMDR START TIME programmed in MMC 501.
4.10.23 Busy
This is the number of times this trunk was busy when accessed by a button or dial code.
D************************ STATION HUNT GROUPS ************************
<———————— 1 OUTSIDE CALL —————————————————————> 5 <-INTERCOM->
2GROUP
3ANSD
4NOT-ANSD
6ANSD
500
0000
0000
0000
501
0000
0000
0000
502
0000
0000
0000
503
0000
0000
0000
504
0000
0000
0000
4.10.24 Outside Calls
These statistics are for outside calls that reach these station groups regardless how they
arrive there.
4.10.25 Group
Listing of all station groups in the system.
4.10.26 ANSD (Answered)
This column is a peg count of all answered trunk calls that rang to the specific group
directory number regardless of how these arrived.
4.10.27 Not-ANSD
The number of times any trunk call directed to the specific group number was not answered
by any member of the group.
4.10.28 Intercom
An intercom call made from a station or device within the system to the specific group
number.
4-58
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.10.29 ANSD
This is a count of how many times an intercom call was answered by any group member of
that specific group.
E************************** INDIVIDUAL STATIONS **********************
1
11
<—————————————-- OUTSIDE CALL ——————————-——————> <—INTERCOM—->
2
3
4
5
6
7
8
9
10
12
13
EXT STATION-NAME ATTA ANSD NOT-ANSD DIALED ICM-TRSF TRK–TRK PICKUP ANSD DIALED
201
0000
0000 0000
0000
0000
0000
0000
0000
0000
202
0000
0000 0000
0000
0000
0000
0000
0000
0000
203
0000
0000 0000
0000
0000
0000
0000
0000
0000
204
0000
0000 0000
0000
0000
0000
0000
0000
0000
205
0000
0000 0000
0000
0000
0000
0000
0000 0000
4.10.30 Outside Calls
These statistics are for outside calls that in any way reach individual stations or devices.
4.10.31 EXT
Listing of all extension numbers in the system. This also includes AA, VM, and SVMI-8
ports.
4.10.32 Station Name
The name for each particular station as programmed in MMC 104.
4.10.33 ATTA
ATTA(Average Time To Answer) for stations is counted in the number of seconds that
ringing signal is applied to a station for trunk calls and recalls. The ATTA is the sum of all
answered times divided by the answered call count. Use the same calculation method as
used for individual trunk ATTA.
4.10.34 ANSD
ANSD is a count of how many times an outside call was answered by the specific station.
Outside callers recalling a station are not counted again when they are answered.
4.10.35 Not-ANSD
Not-ANSD is a count of how many times a trunk call was directed to the station but was
not answered by this station.
© SAMSUNG Electronics Co., Ltd.
4-59
CHAPTER 4. Business Feature Package
4.10.36 Dialed
Peg count of how many times the station made a valid outside call. An outside call is
defined by the SMDR start time in MMC 501.
4.10.37 ICM-TRSF
ICM-TRSF(Intercom-Transfer) is the number of times a trunk call was successfully
transferred to another station using the intercom. It includes both screened and unscreened
transfer.
4.10.38 TRK-TRK
This is the number of times a trunk call was transferred to another trunk(tie line)
This is called a trunk-to-trunk transfer. This field gets pegged every time the station
completes a trunk to trunk transfer.
4.10.39 Pickup
This is a count of the outside calls that were picked up by the specific station. Picked-up
calls are calls that are not ringing at your station but were answered by you. This peg count
is separate from the number of answered call in #5 of Individual Stations section E.
4.10.40 Intercom
Statistics for intercom calls. An intercom call made from a station or a station device within
the system to another station.
4.10.41 ANSD
This is the number of times an intercom call was answered by this specific station.
Screened transfers count as an answered intercom call.
4.10.42 Dialed
The number of times the specific station dialed another station or station group. Screened
transfers count as a dialed intercom call.
4-60
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
4.11 Sample Alarm Report
ALARM REPORT FOR [OfficeServ 100 SAMPLE ] MAR/24/1999 19:45
======================================================================
MM/DD/YYYY ERR.TIME ERR.CODE ERROR DISPLAY
POSITION
======================================================================
03/14/1999
16:45:00 [MNF03] IPC Error
C1-S01
03/14/1999
16:45:00 [MNF03] IPC Error
C1-S04
03/14/1999
16:45:00 [MNF03] IPC Error
C1-S01
03/14/1999
16:45:00 [MNF03] IPC Error
C1-S04
03/14/1999
16:45:00 [MNF03] IPC Error
C1-S01
03/14/1999
16:45:00 [MNF03] IPC Error
C1-S04
03/14/1999
16:46:00 [MNF01] Card Out
C1-S05
03/14/1999
16:46:00 [MNF02] Card In
C1-S05
03/14/1999
16:47:00 [MJD01] SYNC Failure
C1-S05
03/14/1999
16:47:00 [MJD02] SYNC Recvry
C1-S05
03/16/1999
16:47:00 [MNF04] Trunk Fault
C1-S06-P03
03/16/1999
16:48:00 [MNF05] Trunk Recvry
C1-S06-P01
03/16/1999
16:48:00 [MNF05] Trunk Recvry
C1-S06-P02
03/16/1999
16:48:00 [MNF05] Trunk Recvry
C1-S06-P03
03/18/1999
16:51:00 [MNF01] Card Out
C1-S02
03/18/1999
16:51:00 [MNF02] Card In
C1-S02
03/19/1999
17:23:00 [MNF01] Card Out
C1-S03
03/20/1999
17:24:00 [MJC01] DTMF Fault
BASE
03/20/1999
17:24:00 [MNF03] IPC Error
C1-S01
03/20/1999
17:24:00 [MNF03] IPC Error
C1-S04
03/24/1999
17:24:00 [MJD19] PRI Restart
C1-S07
© SAMSUNG Electronics Co., Ltd.
4-61
CHAPTER 4. Business Feature Package
4.12 DECT Service
OfficeServ 100 system provides DECT cordless communications in a single office or
throughout a large commercial or industrial complex. To implement this service, you need
3BSI card, DB(Daughter Board) card and DECT handsets. Users of this service meet
improved overall efficiency, since staff can be reached or make calls wherever they are.
4-62
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide
ANNEX A. Abbreviation
A
AA
Automated Attendant
AC
Alternating Current
ACC
Account Code
AOM
Add On Module
AP
Access Point
ANSD
Answered
ATTA
Average Time To Answer
BGM
Background Music
BLF
Busy Station Indications
BRI
Basic Rate Interface
BSI
Base Station
CAD
Call Activity Display
CCBS
Call Completion to Busy Subscriber
CCNR
Cell Completion on No Reply
CFB
Call Forward Busy
CFNR
Call Forward No Response
CFU
Call Forward Unconditional
CID
Caller Identification
B
C
CLI
Call Line Identification
COS
Class Of Service
CTI
Computer Telephony Integration
DB
Daughter Board
DCS
Digital Communication System
DDI
Direct Dial In
DID
Direct Inward Dialing
DECT
Digital Enhanced Cordless Telecommunications
DHCP
Dynamic Host Configuration Protocol
D
© SAMSUNG Electronics Co., Ltd.
A-1
ANNEX A. Abbreviation
DISA
Direct Inward System Access
DLI
Digital Line Interface
DND
Do Not Disturb
DNIS
Dialed Number Identification Service
DPIM
Door Phone Interface Module
DSP
Digital Signal Processor
DSS
Direct Station Selection
DTMF
Dual Tone Multi Frequency
EPROM
Erasable Programmable ROM
ICC
Internet Call Center
ICM-TRSF
Intercom-Transfer
ID
Identification
IMAP
Internet Messaging Access Protocol
IN-SCP
Intelligent Network Service Control Point
IP
Internet Protocol
IPC
Inter Processor Communication
IPM
Inter Processor Communications And Memory Module
ISDN
Integrated Services Digital Network
ITP
IP Telephone
KDB
Keyset Daughter Board
KSU
Key Service Unit
LAN
Local Area Network
LCD
Liquid Crystal Display
LCP
Local Control Processor
LCR
Least Cost Routing
LED
Light Emitting Diode
E
I
K
L
M
A-2
MCP
Main Control Processor
MGI
Media Gateway Interface
MISC
Miscellaneous
MMC
Man Machine Communication
MOH
Music On Hold
MWSLI
Message Waiting Single Line Interface
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100 General Description Guide/Ed.00
O
OHVA
Off-Hook Voce Announce
OPX
Off Premises Extension
PABX
Private Automatic Branch Exchange
PCB
Printed Circuit Board
PCM
Pulse Code Modulation
PCMMC
PC based Man Machine Communication
PLL
Phase Locking Loop
PRI
Primary Rate Interface
PRS
Polarity Reverse Detection
PSTN
Public Switched Telephone Network
Q-SIG
Q-Signaling
RAM
Random Access Memory
RGU
Ring Generator Unit
P
Q
R
S
SIP
Session Initiation Protocol
SLI
Single Line Interface
SLT
Single Line Telephone
SMDR
Station Message Detail Recording
SMS
Short Message Service
SVMi
Samsung Voice Mail integrated
TAPI
Telephony Application Programming Interface
TEPRI
T1E1PRI
TRK
Trunk
T
© SAMSUNG Electronics Co., Ltd.
A-3
ANNEX A. Abbreviation
U
UA
User Agent
UCD
Uniform Call Distribution
USB
Universal Serial Bus
V
VLAN
Virtual LAN
VoIP
Voice over Internet Protocol
WBS
Wireless Base Station
WIP
Wireless IP Phone
W
A-4
© SAMSUNG Electronics Co., Ltd.
OfficeServ 100
General Description Guide
©2004 Samsung Electronics Co., Ltd.
All rights reserved.
Information in this document is proprietary to SAMSUNG
Electronics Co., Ltd.
No information contained here may be copied, translated,
transcribed or duplicated by any form without the prior written
consent of SAMSUNG.
Information in this document is subject to change without notice.