Craftsman HIGH PRESSURE WASHER 580.76225 Operating instructions

Owner's
anual
CRAFr$1vlnN+
6.75 HORSEPOWER
2200 PSi
2.2 GPM
HiGH PRESSURE WASHER
CAUTION:
Before using this
product, read this manual and
follow all Safety Rules and
Operating Instructions.
HOURS:
SEARS,
ROEBUCK
Part No. B2620 DraI_ 0 (2/5197)
t/>
PRESSURE WASHER
CUSTOMER
HELPLINE
Non. - Fri. 8 a.m. to 5 p.m. (CST)
and CO., Hoffrnan
Estates,
IL 60179 U.S.A.
j
SAFETY RULES ............................
3
STOP,AGE
...............................
ASSEMBLY ..............................
4-5
TROUBLESHOOTING
OPERATION .............................
6-9
REPLACEMENT PARTS ...........
MAINTENANCE
........................
.......................
HOW TO ORDER PARTS ............
10-13
14
15
: ......
16-27
BACK PAGE
LIMITED ONE YEAR WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER
For one year from the date of purchase, when this Craftsman High Pressure Washer is maintained and operated according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in matedal
and workmanship.
if this high pressure washer is used for commercial purposes; this warranty applies for only 90 days from the
date of purchase, tf this high pressure washer is used for rental purposes, this warranty applies for only 30
days after date of purchase.
This warranty does not cover:
o ..Expendable items such as spark plugs and air filters, which become worn during normal use.
o Repairs necessary because of operator abuse or negligence, includingdamage resultingfrom no water being
supplied to pump or failure to maintain the equipment according to the instructionscontained in the owner's
manual.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE HIGH PRESSURE WASHER TO THE
NEAREST SEARS SERVICE CENTER OR DEALER IN THE UNITED STATES.
This warranty gives you specific legal rights and you may also have other rights, which vary from state to
state.
SEARS,
ROEBUCK
AND
CO.,
D/817
WA,
Hoffman
Estates,
IL 60179
NOT CONTACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP,
CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CANTRANSPORTING, ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER.
o
_
read this manual and follow all Safety
AUTION: Before using this product,
Rules and Operating instructions.
o
o
o
,
o
o
o
Engine exhaust gases contain DEADLY carbon monoxide
gas. This dangerous gas, if breathed in sufficient concentrations, can cause unconsciousness or even death.
Operate this equipment only in the open air where adequate ventilation is available.
Gasoline is highly FLAMMABLE and itsvapors are
EXPLOSIVE. Do not permit smoking, open flames, sparks
or heat in the vicinity while handling gasoline. Avoid
spilling gasoline on a hot engine. Allow unit to coot for 2
minutes before refueling. Comply with all laws regulating
storage and handling of gasoline.
o
o
o
o
•
o
o
o
•
•
=
Locate this pressure washer in areas away from combustible materials, combustible fumes or dust.
The high pressure equipment is designed to be used with
Sears authorized parts only. if you use this equipment with
parts that do notcomply with minimum specifications, the
user assumes all risks and liabilities.
°
o
Some chemicals or detergents may be harmful if inhaled
or ingested,causing severe nausea, fainting or poisoning.
The harmful elements may cause property damage or
severe injury.
Do not allow CHILDREN to operate the Pressure Washer
at any time.
Operate engine only at governed speed. Running the
engineat excessive speeds increasesthe hazard of personal injury.Do net tamper with parts which may increase
or decrease the governed speed.
Do not wear loose clothing, jewelry or anything that may
be caught in the starter or other rotating parts.
Before starting the Pressure Washer in cold weather,
check all parts of the equipmentand be sure ice has not
formed there.
Units with broken or missing parts, or without protecWe
housing or covers should NEVER be operated.
The muffler and air cleaner must be installed and in good
condition before operating the Pressure Washer. These
components act as spark arrestors if the engine backfires.
Check the fuel system for leaks or signs of deterioration
such as chafed or spongy hose, loose or missing clamps
or damaged tank or cap. Correct all defects before operating the Pressure Washer.
Do not spray flammable liquids.
•
o
•
=
•
•
=
o
Never allow any part of the body to come in contactwith
the fluid stream. DO NOT come in contact with a fluid
stream created by a leak in the high pressurehose.
High pressurestreams of fluid thisequipment produces
can pierce skin and its underlyingtissues, leading to serious injury and possible amputation.
Never aim tile gun at people, animals or plants.
High pressurespray can cause paint chips or other pa_cies to become airborne and fly at high speeds.
Nways wear eye protection when you use this equipmentor
when you are in the vicinity where the equipmentis in use.
Operate the pressure at no more than the PSI fluid pressure rated for your pressurewasher.
Never move the machine by pulling on the high pressure
hose. Use the handle provided on the top of the unit.
Always be certain the spray gun, nozzles and accessories
are correctly attached.
Never use a spraygun which does not have a tri_lgerlock
or trigger guard in place and in working order.
Use a respirator or mask whenever there is a chance that
vapors may be inhaled. Read all instructionswith the mask
so you are certain the mask will provide the necessary
protection against inhalingharmful vapors.
High pressurespray may damage fragile items including
glass. Do not point spray gun at glass when in the jet
spray mode.
Keep Me hose connected to machine or the spray gun
while the system is pressurized. Disconnecting the hose
while the unit is pressurized is dangerous.
Hold the spray gun firmly in your hand before you start the
unit. Failure to do so could result in an injuryfrom a whipping spray gun. Do not leave the spray gun unattended
while the machine is running.
The cleaning area should have adequate slopes and
drainage to reduce the possibilityof a fall due to slippery
surfaces.
Keep water spray away from electric wiring or fatal electric
shock may result.
Do not adjust unloader valve to a pressure in excess of
machine rating.
Do not secure trigger gun in the pull-back (open) position.
Do not by-pass any safety device on this machine.
The muffler and engine heat up during operation and
remainhot immediately after shutting it down. Avoid contact with a hot muffler or engine or you could be severely
bumed.
MAINTENANCE
AND STORAGE:
* Operate and storethis unit on a stable surface.
,
High pressure hose can develop leaks from wear, kinking,
abuse, etc. Water spraying from a leak is capable of injecting material into skin. Inspect hose each time before using
it. Check all hoses for cuts, leaks, abrasions or bulging of
cover, or damage or movement of couplings. If any of
these conditions exist, replace hose immediately.Never
repair high pressure hose. Replace it with another hose
that meets minimum pressure rating of your pressure
washer.
LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS.
IT MEANS "ATTENTION!I!
BECOME ALERT!H YOUR SAFETY iS INVOLVED."
I
I
CARTON CONTENTS
How TO SET UP YOUR PRESSURE WASHER
The following parts are shipped loose with your pressure
washer:
For the most part, your Craftsman High Pressure Washer
has been assembled at the factory. You must, however,
attach the wire form, assemble the spray gun, and attach
the high pressure hose to the pump and spray gun.
=' Main Unit-- pressure washer with wheels,
guide handle.
o High Pressure Hose
• Parts Box #1 (which includes items listed below)
• Rotating Brush
• Vehicle/Boat Wash
® House/Multi-purposeWash
® Parts Box #2(which includes items listed below)
o Adjustable Nozzle
,, Turbo Nozzle
,, Spray Gun
,, Nozzle Extension
° Wire Form
Motor Oil
° Manual Bag (which includesthe items listed below)
= Owner's Manual
, Nozzle Cleaning Kit
• "O"-Ring Kit
Become fam']iiar with each piece before assembling the
pressure washer. Check all contents against the illustration on Page 6. if any parts are missing or damaged, call
the Pressure Washer Helpline at 1-800-222-3136,
TO REMOVE
CARTON
PRESSURE
WASHER
FROM
Remove parts boxes included with pressure washer.
The high pressure hose is Packed in the bottom of the
carton. Remove the hose.
= Slice two corners at handle end of carton from top to
bottom so the panel can be folded down flat.
°
Raise handle, secure in place with the locking caps
and roll the pressure washer out the open end of the
carton.
Locking Caps
°
Check carton for additional loose parts.
,, While facing the rear of the Pressure Washer, insert
the wire support with the longer arm positionedon the
left. From this view the hook should resemble a "J".
/
o
Cut tie wrap on chemicalinjection tube. Remove chemical injection filter, thread chemical injec_ontube through
the wire form and reinsert filter into tube.
*
Cut the tie wraps on the high pressure hose and
connect high pressure hose to gun. Tighten by
hand.
°
Place assembled spray gun on holder.
,
Place turbo nozzle in grommet hole in base.
o Remove plastic cap and connect high pressure
hose to pump. Tighten by hand.
CHECKLIST
Before you operate your new high pressure washer
please review the following checklist:
Attach High
Pressure
hose here
Attach nozzle extension to spray gun.
•
All assembly instructions have been completed.
•
The high pressure hose connections to the spray
gun and to the pump are tight and secure.
While learning how to use your high pressure
washer, pay extra attention to the following important
item:
Engine oil is at proper level
Important: Any attempt to crank or start the engine
before it has been properly serviced with the recommended oil may result in an engine failure. See Page
9 for instructions on adding oil and proper oil specifications.
Attach adjustable nozzle to the nozzle extension.
Important: The water supply to your pressure washer must be connected and turned on prior to starting
your engine.
°
Be sure gas tank is filled properly with clean,
fresh, unleaded gasoline.
o
Become familiar with all controls - their location
and function. Operate those controls before starting the engine.
5
KNOW YOUR HIGH PRESSURE WASHER
Read this owner's manual and safety rules before operating your high pressure washer. Compare the illustrations with your high pressure washer to familiarize yourself with the locationsof various controls and adjustments.
Save this manual for future reference.
Chemical Injection
Tube and Filter
High Pressure Hose
Spray Gun
Gas Cap
Nozzle Extension
Air Filter
Adjustable
Engine Throttle Control
Nozzle
Primer Bulb
Water Inlet
Rotating Brush
High Pressure
Outlet
Pump
Car Wash
" House Wash
Rotating Brush Adapter
Turbo Nozzle -- Attaches to the nozzle extension and
creates a high pressure stream that rotates in a circular
pattern.
Pump - Develops high water pressure.
Engine Throttle Control - Sets engine in starting mode
for recoil starter; STOPS running engine.
Air Filter -- Dry type filter element limitsthe amount of
dirt and dust that gets in the engine.
Adjustable Nozzle -- Attaches to the nozzle extension
and adjusts the spray pattern to be either a low pressure
stream or a high pressure stream. Twisting the nozzle
adjusts the narrow spray pattern to a fan spray pattern.
Note: You can only siphon detergent in the low pressure
mode.
Spray Gun -- Controlsthe application of water onto
cleaning surface with trigger device. Includes safety latch.
Car Wash -- Use the concentrate to wash your car or
boat.
Primer Bulb -- Prepares a cold engine for starting.
Recoil Starter -- Used for starting the engine manually.
Chemical Injection Tube and Filter -- Mixes water and
detergent in outlet water flow.
House Wash -- Use the concentrate to wash your
House.
High Pressure Outlet -- Connection for high pressure
hose.
Nozzle Extension -- Attach one end to the spray gun.
Attach the other end of the nozzle extension to either the
adjustable nozzle, turbo nozzle or rotating brush adapter.
Water inlet -- Connectionfor garden hose.
High Pressure Hose -- Attach one end to the pump,
Attach the other end to the spray gun,
Rotating Brush -- Use this brush for automatic scrubbing of surfaces. Attaches to the nozzle extension. Note:
When attaching to nozzle extension, you must use the
accessory adapter.
Oil Fill Cap -- Fill engine with SAE 30 oit here.
Gas Cap -- Fill gas tank with unleaded gasoline here,
Rotating Brush Adapter -- Allows the rotatingbrush to
be attached to the nozzle extension.
6
HOW TO USE YOUR PRESSURE WASHER
IF YOU HAVE ANY PROBLEMS operating your pressure washer, please call the pressure washer helpline
at 1-800-222-3136.
A
DANGER! NEVER adjust spray pattern
when spraying. NEVER put hands in front
of spray nozzle to adjust spray pattern.
You could be injured.
HOW TO USE THE ADJUSTABLE NOZZLE
One of the nozzles you can attach to the nozzle
extension is the adjustable nozzle. You can slide the
adjustable nozzle forward and backward to adjust the
spray pattern to be either high pressure or tow pressure. You can also twist the adjustable nozzle from
side to side to adjust the spray so it is concentrated
in a stream pattern or expanded into a fan pattern.
o
Slide the nozzle forward to adjust the spray to low
pressure mode. Slide the nozzle backward to
achieve high pressure,
•
If you get spray nozzle too close, especially using
high pressure mode, you may damage the cleaning surface.
APPLYING DETERGENT AND CLEANING WiTH
ADJUSTABLE NOZZLE
IMPORTANT: Use soaps designed specifically for
pressure washers. Household detergents could damage the pump.
IMPORTANT: You must attach all hoses before you
start the engine. Starting the engine without all the
hoses connected and without the water turned ON
will damage the pump.
To apply detergent follow these steps:
°
Prepare the detergent solution as required by the
job. (For the enclosed bottles of detergent, add
the 8 ounces of chemical to a 1 gallon plastic bottle with handle (not included). Fill the rest of the
bottle with water.)
o
Hang the detergent solution on the "J" hook on
the wire form on the guide handle.
Place small filter on the chemical injectiontube
into the detergent container.
Slide nozzle backward
to place in high pressure mode.
Slide nozzle forward
for low pressure
mode.
Twisting the nozzle adjusts the spray pattern from
a narrow pattern to a fan pattern.
o
Slide the adjustable nozzle forward to low pressure mode. Detergent cannot be applied with
nozzle in high pressure position.
Note: The first step involves applying an appropriate
detergent/solvent solution to penetrate and loosen
grime. The detergent is applied at tow pressure to
avoid splashing, overspraying and waste. Leave the
solution on surface for 3 to 5 minutes to allow solution to work.
Note: The second step involves cleaning the surface
you have prepared with the pressure washer and
then rinsing it clean.
Twist nozzle counterclockwise for fan
spray pattern.
Twist no_te
clockwise for narrow
spray pattern.
For most effective cleaning, keep spray nozzle
between 8 to 24 inches away from cleaning surface.
o
Review the use of the adjustable nozzle.
o
Connect garden hose to water inlet (see 'q'O
START PRESSURE WASHER"), check that high
pressure hose is connected to spray gun and
pump (see ASSEMBLY), and start engine.
For cleaning, start at lower portion of area to be
washed and work upward, using long, even overlapping strokes.
Allow the detergent to soak in between 3-5 minutes before washing and rinsing.
RINSING WiTH THE PRESSURE WASHER
WARNING Be extremely careful if you must
use the pressure washer from ladder, scaffolding or any other relatively unstable location. Pressure in a running washer builds in
the wand as you climb. When you press the
trigger, the recoil from the initial spray could
force you to fail, or if you are too close to the
cleaning surface, high pressure could force
you off a climbing apparatus.
•
Hook up the water supply and start your pressure
washer (see TO START THE PRESSURE WASHER).
•
Slide adjustable nozzle back to high pressure position
and wait for detergent to clear. Detergent will not flow
when in the high pressure mode.
= When detergent has cleared you may want to expand
the spray pattern for a more gentle rinsing action.
Start at top of area to be rinsed, working down with
same action as for cleaning.
You can also stop detergent from flowing by simply
removing_phon from bottle.
The high pressure spray is most effective when the tip of
the wand is held between 8 to 24 inches from the surface
being cleaned.
Important: The turbo nozzle produces an extremely high
pressure spray which is capable of removing paint and
cuffing holes through surfaces if held too close. Always
make sure the surface you will clean will not be damaged
by the high pressure spray.
HOW TO USE THE ROTATING BRUSH
Your pressure washer comes equipped with a rotating
brush. Use the brush to clean especially dirty surfaces, it
is a soft bristle brush with feathered ends that will not
scratch surfaces.
To connect the rotating brush to the spray gun:
HOW TO USE ADJUST PRESSURE
THE PRESSURE
CONTROL
KNOB
USING
Located on the pump is a pressure controlknob. You can
increase and decrease the pressure of the spray by turning the knob clockwise or counterclockwiserespectively.
_,The knob is set at maximum pressure at the factory.
HOW
TO USE THE TURBO
NOZZLE.
The turbo nozzle rotates the high pressure stream in a
rapid circular pattern. This increases the cleaning effectiveness of the high pressure spray, Attach the turbo nozzle on the end of the nozzle extension.
o
Attach the accessory adapter to the rotating brush.
o
After attaching the accessories adapter onto the rotating brush, attach the accessory adapter to the nozzle
extension.
-
After attaching the accessories adapter onto the nozzle extension, attach nozzle extension onto spay gun.
Note: The rotating brush operates in low pressure
setting allowing you to dispense chemical with the
brush.
BEFORE STARTING THE PRESSURE WASHER
TO START YOUR PRESSURE
To operate the engine you wilt need to do the following:
You have assembled your high pressure washer and
have prepared the engine for starting. You are now ready
to clean your car, boat or whatever you plan to clean.
ADD ENGINE OIL
Use only high quality detergent oil rated with API
service classification SF or SG rated SAE 30 weight.
Use no special additives.
o
Place pressure washer on a level surface
,
Clean area around oil fill and remove oil dipstick.
o
Wipe dipstick clean.
°
Pour oil from enclosed bottle into the oil fill opening
until oil reaches FULL mark on the dipstick. Stop and
check the oil level periodically. DO NOT OVERFILL.
WASHER
Ptace the pressure washer in an area close enough
to an outside water source that can flow at a rate of at
least 2.2 gallons per minute. Connect a garden hose
to the water spout.
Check that the high pressure hose is tightly connected to the spray gun and to the pump. See ASSEMBLY section for illustrations.
e
Pull back on the locking collar to remove the female
quick-connect from pump.
Assembled
Quick-Connect
= Install oil dipstick, hand tighten securely.
Pull back on locking
collar to separate
Check oil level often during engine break in.
ADD GASOLINE
Use fresh, clean, unleaded regular, unleaded premium, or reformulated automotive gasoline only.
Do not use leaded gasoline.
Disassembled
male end
DANGER! NEVER fill fuel tank indoors.
NEVER fill fuel tank when engine is running or hot, DO NOT light a cigarette or
smoke when filling the fuel tank.
A
Note: You wilt also need to pull back on the lockingco!lar to attach the female quick-connect.
Check inlet screen. If the screen is dirty, clean
before attaching to garden hose. If the screen is
damaged, Do not connect to the garden hose.
Replace with the inlet screen provided in the o-ring
kit or cal! 1-800-366-PART to order a replacement
(pln B2384).
DANGER! Do not overfill the fuel tank.
Always leave room for fuel expansion.
Wipe any fuel spillage from engine and
equipment before starting engine
Note: Do not use gasoline containingmethanol (wood
alcohol). Gasoline containing up to 10% ethanol or grain
alcohol ("Gasohol"), or up to 15% MTBE (Methyl Tertiary
Butyl Ether), may be used but requires special care when
engine is unused for extended periods.
Attach the female quick-connect to garden hose and
then attach the garden hose to the water inlet. Make
sure the quick-connect is locked together.
See "Storage" instructionson Page 15.
Clean area around fuel fill cap, remove cap.
o Add "UNLEADED" regular gasoline, slowly, to fuel
tank.
Important: Never mix oil with gasoline.
,
Disassembled
female end
Install fue! cap and wipe up any spilled gasoline.
9
-
Turn on the water.
Note: if after 3 pulls the engine fails to start, prime the
engine again, purge the gun and pull the recoil starter
handle rapidly (Max. 3 pulls). •
IMPORTANT: Do not run pump without the water supply connected and turned on. You must follow this caution or the pump wilt be damaged.
•
HOW TO STOP YOUR PRESSURE WASHER
Move the Throttle Control Lever to the 'Fast'
position
® Push primer bulb 3 times. Wait about two 2 seconds
between each push. In cold weather, (55°F/13°C or
below) push 5 times.
Note: Do not use primer to restart a warm engine after a
short shut down.
Positionthe nozzle in the low pressure mode (nozzle
slid forward) and squeeze the triggeron the spray
gun to relieve the air pressure caused by turning ON
the water. Water will spew out the gun in a thin
stream. Continue to hold trigger until you have a
steady stream of water and no air remains in the system. This will make it easier to pull start the engine.
Release the trigger.
=
Engage the safety latch on the gun.
-
Grasp rope handle and pull slowly until you feet some
resistance. Then pull cord rapidlyto overcome compression, prevent kickback and start the engine. Let
rope return to starter slowly ................
-
Move the Throttle Control Lever to the 'Slow' position.
•
Wait for the engine to idle down.
.
Move the Throttle Control Lever to the 'Stop' position,
•
Simply shutting off the engine will not release
pressure in the system. Squeeze trigger on the
spray gun to relieve pressure in the hose.
Note: A small amount of water wilt squirt out from the
spray gun when you release the pressure.
SIPHONING
We recommend that you DO NOT siphon standing water
for your water supply. Contaminated, brackish or dirty
water can damage the pump. Connect only to household
water supply.
TIPS
,
Never use the garden hose inlet to siphon detergent
or wax .......
•
Note: Always keep the Throttle Control Lever in the
'Fast' position when operating the pressure washer.
]0
If you have the spray nozzle too far away, the cleaning will not be as effective.
CUSTOMER RESPONSiBiLITIES
MAINTENANCE SCHEDULE
FiLL IN DATES AS YOU COMPLETE
REGULAR SERVICE
HOURLY OPERATING INTERVAL
Before Each
Use
MAINTENANCE TASK
SERVICE DATES
Every" 100
Hours or
Houm or
Every
25
Yearly
Yearly
PRESSURE WASHER
Check/clean
waterinletscreen
onquick,-connect.
Xt
,,,,,,,,,,,_,,,,,,
................................
Checkhighpressure
hose,
X
Checkdetergent
hose.
X
• ,,,,,,,,,,
Checkspraygunandassemblyforleaks.
_
Purgepumpofairandconta_nants.
,,
•
,
i
i
X
X
ENGINE
Checko11
level
X
Change
engineoil,
X*
,,,_,,,,,
......
Service
air cleaner,
X',t _"
x
Clean/replace
sparkplug.
Prepare unit for storage if it is to
remain idle for longer than 30 days.
Prepare for storage.
I" Clean if clogged, Replace if perforated or tom,
* Change oil after first 2 hours then 25 thereafter. Change sooner when under dirty or dusty conditions.
"* Clean more often under dirty or dusty conditions.
GENERAL
RECOMMENDATIONS
Engine Specifications
The warranty of the high pressure washer does not cover
items that have been subjected to operatorabuse or negligence. To receive full value from the warranty, operator
must maintain high pressure washer as instructed in this
manual.
ENGINE MODEL
Craftsman
RATED HORSEPOWER
6,75
DISPLACEMENT
172cc
Some adjustments will need to be made periodically to
properly maintain your high pressure washer,
SPARK PLUG: Type:
Champion RN4C
or equivalent
0,030 inch l'0,76mm)
Set Gap to:
All adjustments in the Service and Adjustments section of
this manual should be made at least once each season.
Once a year you should clean or replace the spark
plug and clean or replace the air filter and check the
gun and wand assembly for wear. A new spark plug
and clean air filter assure proper fuel-air mixture and
help your engine run better and last longer.
Pressure Washer Specifications
2200 psi
FLOW RATE
2.2 GPM
DETERGENTMIX
Use undiluteddeterqent..........
WATER SUPPLY
TEMPERATURE
Not to Exceed !40°F
1,5 U.S, quart
OIL
SAE 30 weiaht
SOLID STATE IGNITION
AIR GAP
0.0125 inch
tn the State of California a spark arrestor is required by
law (Section 4442 of the California Public Resources
Code). Other states may have similar laws, Federal laws
apply on federal lands.
PRODUCT SPECIFICATIONS
PRESSURE
GASOLINE CAPACITY
Note: tf you equip the engine of your pressure washer
with a spark arrestor muffler, the spark arrestor must be
maintained in effective working order by the owner/operator.
You can order a spark arrestor through your Sears
Service Center.
11
BEFORE EACH USE
ENGINE MAINTENANCE
•
Check water inlet screen for damage.
CHECKING OIL LEVEL
•
°
•
•
•
Check high pressure hose for leaks.
Check detergent inlet hose and filter for damage.
Check gun and wand assembly for leaks.
Purge pump of air and contaminants.
Check engine oil level.
Oil level should be checked prior to each use or at least
every 5 hours of operation. Keep oil level maintained.
PRESSURE WASHER MAINTENANCE
Check and Clean Inlet Screen: Remove quick-connect
and examine inlet screen on the female connector. Clean
if it is clogged or replace if it is tom.
CHANGING ENGINE OIL
Change engine oil after first 2 hours then every 25 hours
thereafter. If you are using your pressure washer under
extremely dirty or dusty conditions, or in extremely hot
weather, change oil more often.
Change oil while engine is still warm from running, as
follows:
Check High Pressure Hose: High pressure hose can
develop leaks from wear, kinking, abuse. Inspect hose
each timebefore using it. Check for cuts, leaks, abrasions
or bulgingof cover, or damage or movement of couplings.
If any of these conditionsexist, replace hose immediately.
,_
Disconnect spark plug wire from spark plug and keep
it away from spark plug.
Before you tip the pressure washer to drain oil, drain
fuel tank by running pressure washer until fuel tank is
empty.
DANGER: Water spraying from a leak is
capable of injecting material into skin.
NEVER repair high pressure hose. Replace
with hose that meets minimum pressure rat-_ ing of your pressure washer.
Check Detergent Hose: Examine the filter on the detergent hose and clean if clogged. Hose should fit tightly on
barbed fitting. Examine hose for leaks or tears. Replace
the filter or hose if either is damaged.
Check Gun and Wand: Examine hose connection to gun
and make sure it is secure. Test trigger by pressing it and
makingsure it springs back into place when you release it.
Put safety latch in UP positionand test trigger. You should
not be able to press trigger.
Purge Pump of Air and Contaminants
To remove the air from the pump, follow these steps:
.
Set up the pressure washer as described in the
ASSEMBLY section and connect the water supply.
°
Remove'the nozzle extension from the gun.
o Pull the trigger on the gun and hold.
Clean area around oil fill, remove oil fill cap/dipstick.
Wipe dipstick clean.
Tip your pressure washer to drain oil completely from
the oil fill tube into a suitable container. When
crankcase is empty, return the pressure washer to
upright position.
Fill engine crankcase with recommended oil until oil
level is at FULL point on dipstick. Do not overfill above
that mark. POUR SLOWLY.
When engine crankcase is filled to proper level, install
and tighten oil cap/dipstick.
SERVICE AIR CLEANER
Your engine will not run properly and may be damaged if
you run it with a dirty air cleaner.
Replace the air cleaner once every 100 hours of operation or once each year, whichever comes first. Replace
more often if operating under dirty or dusty conditions.
Replacements are available at your local Sears
Authorized Service Center.
Important:
To remove the contaminants from the pump, follow these
steps:
•
Important: Never run engine without complete air cleaner installed on engine.
Set up the pressure washer as described in the
ASSEMBLY section, and connect the water supply.
•
Remove the nozzle attachment from the gun.
°
Start the engine according to instructions in OPER_,TION section.
o
Putt the trigger on the gun and hold.
O
When the water supply is steady and constant,
engage the safety latch and refasten the nozzle
attachment.
Do not attempt to clean or oil filter.
To clean or replace the air cleaner, follow these
steps:
TURN COVER 3"0 THE LEFT
(COUNI_RCU:X;k_,_)'tO
12
_P,JRN GOVER
" .1'0
THE I_r,rr
Turn cover to the left (counterclockwise) and
remove it and filter from flange. Discard filter.
o
Clean cover and flange thoroughly.
o
Insert new filter into cover.
o
Shut off the engine and turn off the water supply.
Separate the nozzle from the nozzle extension,
o
Rotate to stream setting.
,,
Remove orifice from the end of the nozzle using the
allen wrench included with the kit or a 2ram or 5/64
allen wrench.
•
Use the wire included in the kit or a small paper clip
to free the foreign materials clogging or restricting
the nozzle.
Position cover and filter firmly against flange with
tab on cover inserted into lower left comer of slot in
flange.
Push cover firmly against flange and turn it to the
right (clockwise) as far as it will go. Be sure retainers are locked around flange.
CLEAN/REPLACE SPARK PLUG
Change the spark plug every 100 hours of operation or
once each year, whichever comes .first. This will help
your engine to start easier and run better. Replace with
champion RN4C or equivalent type spai'k plug.
Clean area around spark plug
Remove and inspect spark plug.
Replace spark plug if electrodes are pitted, burned
or porcelain is cracked. For replacement use
Champion RN4C only.
insert wire into orifice and turn back and forth to
clear obstruction.
Remove additional debris by back flushing water
supply through wand. Back flush between 30 to 60
seconds. Turn wand to stream spray and move nozzle from tow to high pressure while flushing.
Check electrode gap with wire feeler gauge and set
gap at 0.030 (0.76mm) if necessary.
SET PLUG
GAP AT 0.030
inch
(0.76 ram)
NOZZLE
MAINTENANCE
If the nozzle becomes restrictedor clogged with foreign
materials, such as dirt, excessive pump pressure may
develop. A partially clogged nozzle can cause a pulsing
sensation during use. This generally is not a pump
related problem, but rather a clogged or partially
restricted nozzle.
Reinstall orifice into nozzle. DO NOT overtighten.
o
Reconnect nozzle to nozzle extension.
•
Reconnect the water supply, turn ON the water, and
start the engine.
-
Test the pressure washer by operating with nozzle
in the high and the tow pressure positions.
If the nozzle becomes clogged or partially restricted,
immediately clean the nozzle with the kit included with
your pressure washer by following these instructions:
!3
O-RING MAINTENANCE
1 O-Ring (p/n B2386) for the outside of the Male
Quick-Connect,
Through the normal operation of your pressure washer,
O-Rings, which keep the connections of the hoses and
gun tight and leak-free may become worn or damaged.
Provided with your pressure washer is an O-Ring
Maintenance Kit which provides replacement O-Rings,
Rubber Washer and Quick Connect filter.
0
Parts in the O-Ring Kit Include:
-
2 O-Rings (pin 97837) for each end of the nozzle
extension,
•
1 Water Inlet Screen (p/n 132384)for the Female
Quick-Connect,
= 2 O-Rings (pin B2264) for the ends of the high pressure hose.
1 o-ring (p!n B2688) for the connection end of the .....
rotating brush.
/
O-Ring
Note: The above two O-Rings are close in size. Please
match carefully to assure proper O-Ring usage.
.
1 Rubber Washer (pin B2385) for the inside of the
Male Quick-Connect.
To remove a worn or damaged O-Ring:
o
]4
Use a small flathead screwdriver to get underneath
the O-Ring and pry it off.
AFTER EACH USE
To avoid engine problems, the fuel system should be
emptied before storage of 30 days or longer. Follow these
instructions:
Water should not remain in the unit for long periods of time.
Sediments of minerals can deposit on pump parts and
"freeze" pump action. Follow these procedures after every
use:
PROTECT FUEL SYSTEM
o Remove all gasoline from the fuel tank to prevettt gum
deposits from forming on these parts and causing possible malfunction of engine.
Flush detergent hose by placing the injectorfilter into
a pail of clear water while running Pressure Washer
with nozzle in low pressure mode. Flush until you can
see clear water running through the tube.
DANGER:
Drainaway
fuel from
into approved
container
outdoors,
open flame.
Be
sure engine is cool. Do not smoke.
Shut off the engine and let it coot, then remove all
hoses,
o
CAUTION: Be sure throttle lever is in
"STOP" position before you continue. If
you start engine without the proper water
supply connected, you can damage the
pump.
Note: tf "Gasohol" has been used, complete above
instructions and then put 1/2 pint of unleaded gasoline
intofuel tank and repeat above instructions.
Empty the pump of all pumped liquids by pulling recoil
handle about 6 times. This should remove most of the
liquid in the pump.
Coil the high pressure hose and inspectit for damage.
Cuts in the hose or fraying of it could result in leaks
and toss of pressure. Should any damage be found,
replace the hose. DO NOT attempt to repair a damaged hose. Replace the hose with the genuine
Craftsman part.
Drain water from hose and properly hang it on the
wire support provided on the guide handle.
Note: Fuel stabilizer (such as STA-BIL) is an acceptable
alternative in minimizing the formation of fuel gum
deposits during storage. Add stabilizer to gasoline in fuel
tank or storage container. Run engine at least 10 minutes
after adding stabilizer.
CHANGE OIL
While engine is still warm, drain oil from crankcase. Refill
with recommended grade. (See Changing Oil Level on
Page 12.)
OIL CYLINDER BORE
DANGER: NEVER store engine with fuel in I
tank indoors or in enclosed, poorly ventilat- I
ed areas where fumes may reach an open
flame, spark or pdot light as on a furnace,
water heater, clothes dryer or other gas
appliance,
•
o
AUTION:
Avoid spray
fromslowly.
spark plug
hole
when cranking
engine
Install spark plug. Do not connect spark plug wire.
OTHER
CAUTION:
must protectFailure
your unit
from
freezingYou
temperatures.
to do so
will permanently damage your pump and
render your unit inoperable.
Do not store gasoline from one season to another,
@
WINTER STORAGE
To protect the unit from freezing temperatures:
•
Remove spark plug and squirt about 1 ounce (30 rnl)
of engine oil into the cylinder. Cover spark plug hole
with rag. Crank slowly to distribute oil.
l_k
Store in a clean, dry area.
,_
Run engine until engine stops from lack of fuel. Make
sure you have water supply to pump inlet connected
and turned ON.
o
Draw RV antifreeze (antifreeze without alcohol) into
the pump by pouring the washer fluid into a 3-foot
section of garden hose connected to the inlet adapter
and pulling the recoil handle twice.
°
LONG TERM STORAGE
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your unit indoors and cover it to give
protection from dust and dirt. BE SURE TO EMPTY
THE FUEL TANK.
Cover your unit with a suitable protective cover that
does not retain moisture.
IMPORTANT: NEVER cover your pressure washer while
engine and exhaust area are warm,
If you do not plan to use the PressureWasher for more than
30 days, you must prepare the engine for longterm storage.
Note: As always, prepare the pressure washer pump as
you would after each use.
15
I
PROBLEM
Pumphasfollowingproblems:
failureto producepressure,or
erraticpressure,chattering,lossof
pressure,low watervolume.
Detergentfails to mix with.
CAUSE
CORRECTION
2. Water inletis blocked,
1. Pull nozzlebackwardfor high
pressuremode.
2, Clearinlet
3. Inadequatewatersupply
3. Provideadequatewaterflowat
1. Nozzlein lowpressuremode.
4.
Inlet hose is kinked or leaking
5.
Clogged water inlet screen.
6.
7.
Water supply is over 140°F.
Outlet hose is blocked.
8.
Outlet hose leaks.
9,
Gun leaks.
4,
5.
6.
7.
least 2.2 gpm.
Straighteninlethose,patchleak.
Replace/ cleanwaterinletscreen.
Providecoolerwatersupply,
Clear blocksin outlethose,
10. Nozzle is obstructed,
8. Replaceoutlethoseif leaking.
9. Replaceo-ringor gunif necessary.
10. Clearnozzle.
1!.
Pump is faulty.
11. ContactSearsServiceDepartment.
Detergent line isnot submerged.
1. Insert chemicalline intodetergent.
1.
in detergent spray
spray=:
2.
Chemical filter is clogged.
3; Nozzleis in highpressuremode.
2. Cleanor replacefilterldetergent
line,
3. Push nozzleforward for
low pressuremode.
Enginerunsgoodwhen notspraying
butdies whenyou beginto spray.
Engine speed is too slow.
Contact SearsServiceDepartment.
Enginewiltnot start;or starts
and runsrough
1.
Dirty air cleaner
2.
Out of gasoline,
i. Cleanor replaceair cleaner,
2. Fill fuel tank,
3.
Stale gasoline,
4.
Spark plug wire not connected
3. Drain gas tank;fill withfresh fuel.
4. Connectwireto sparkplug.
to spark plug.
8. Excessivelyrichfuel mixture.
9. Intakevalvestuckopenor closed.
5. Replacesparkplug.
6. Drain gastank;fill withfresh fuel.
7, Set enginethrottlecontrolleverto
fast position,chokein run position,
8. ContactSearsServiceDepartment.
9. ContactSearsServiceDepartment,
10. Enginehas'lostcompression.
10. ContactSearsServiceDepartment.
Engineshutsdownduring
1,
Out of gasoline.
1,
Fill fueltank.
operation
2.
Air filter dirty
2,
ReplaceAirfilter.
Enginelacks power.
Dirty air filter,
5.
Bad spark plug.
6.
Water in gasoline,
7.
Overchoking or ftooded
Replaceair filter.
]6
17
CRAFTSMAN
2200 PSI HIGH PRESSURE
WASHER 580.762200
Craftsman 4-C¥cte Engine 143.986714
1111
161
157
2O
119
i01
27g
42
17
41
43
"_ 310
45
==_-3o9
2O7
266
46
""305
",3_
178
]8
CRAFTSMAN 2200 PSi HiGH PRESSURE WASHER 580,762200
Craftsman 4=Cycle Engine 143.986714
Item
Part#
I
2
6
7
36835A
26727
33734
36557
12
12A
32447
36558
12B
14
15
16
17
t8
36694
28277
30589
34839A
31335
651018
19
20
30
40
36281
32600
37208
35544A
40
35545A
40
35546
4!
41
35541
35542
41
35543
42
42
42
43
45
35547A
35548A
35549
20381
32B75A
46
48
50
52
32610A
35616
37011
29914
Description
Qty.
Cylinder (Incl. 2 &. 20)
Dowel Pin
Breather Element
Breather Ass'y.
(Incl. 6 & 12A)
Breather Tube
Breather Cover & Tube
(Znct. 12B)
Breather Tube Elbow
Washer
Governor Rod (Incl. 14)
Governor Lever
Governor Lever Clamp
Screw, Torx T-15, 8-32 x
19/64"
Extension Spring
Oil Seal
Crankshaft
Piston, Pin & Ring Set
(Std:)
Piston, Pin & Ring Set'
1
2
1
(.olo" os)
I
Piston, Pin & Ring Set
(.020" OS)
Piston & Pin Ass'y. (Std.)
Pistcrn & Pin Ass'y.
(.010" OS) (incl. 43)
Piston k Pin Ass'y.
(.020" OS) (Incl. 43)
Ring Set (Std.)
Ring Set (.010" OS)
Ring Set (.020" OS)
Piston Pin Retaining Ring
Connecting Rod Ass'y.
(ZncL 46)
Connecting Rod Bolt
Valve Lifter
Camshaft (MCR)
Oil Pump Ass'y.
l_m
Part#
69
70
37130
37190
72
72A
75
80
81
82
36083
28534
28460
30574A
30590A
30591
83
86
89
90
92
93
t00
101
103
30588A
650488
610961
611213
650815
650816
34443B
610118
651007
110
119
120
125
36230
36738
36721
36471
125
36472
126
29314B
t26
29315C
1
1
1
!
I
1
1
1
I
1
1
1
1
1
1
!
1
1
1
1
2
1
2
2
1
1
130 650912
130A 650999
135 34645
150
151
t53
154
]9
31672
31673
36649
650913
Description
Mounting Flange Gasket
Mounting Flange
(Incl. 72 thru 83,306)
Oil Drain Plug
Oil Drain Plug
Oil Seal
Governor Shaft
Washer
Governor Gear Ass'y.
(incL 81)
Governor Spool
Screw, 1/4-20 x 1-1/4"
Flywheel Key
Flywheel
Bellevilte Washer
Flywheel Nut
Solid State ignition
Spark Plug Cover
Screw, Torx "1"-15,
10-24 x 15(16"
Ground Wire
Cylinder Head Gasket
Cylinder Head
Exhaust Valve (Std.)
(Incl. 151)
Exhaust Valve (t/32" OS)
(Inc!. 151)
Intake Valve (Std.)
(Incl. 15t)
Intake Valve (1/32" OS)
(Inc!. 151)
Screw, 5/16-18 x 1-1(2"
Screw, 5!16-18 x 2-41/64"
Resistor Spark Plug
(RN4C)
Valve Spring
Valve Spring Cap
Push Rod Guide
.Rocker Arm Stud
Qty.
1
1
1
t
1
1
1
1
1
6
1
1
1
1
1
1
2
t
1
1
1
1
1
1
4
1
1
2
2
1
t
CRAFTSMAN 2200 PSI HiGH PRESSURE WASHER 580.762200
Craftsman 4-Cycle Engine 143o986714
Item
155
I57
15B
159
160
161
Part#
35624A
650914
36629
35626
35718
30063
Description
Rocker Arm
Lock Nut
Push Rod
Rocker Arm Cover Gasket
Rocker Arm Housing
Screw, Torx T-30, 114-20
x 1/2"
178 29752
Nut &. Lock Washer,
114-28
182 30088A
Screw, 114-28 x 1"
184 26756
Carburetor Gasket
185 36579
intake Pipe
186 34337
Governor Link
187
36580
Spacer
200
35727
Control Bracket
(ZncL 202 thru 205)
202
36482
Compression Spring
203_ 31342
Compression Spring
204
651029
Screw, Torx T-I0,
5-40 x 71t6"
205
651019
Screw, Torx T-10,
............. 6'32 X 41164 ............
207
34336
Throttle Link
209
30200
Screw, 10-24 x 9116"
215
32410
Control Knob 1
223
651044
Screw, 1/4-20 x 2-25132"
224
36581
intake Pipe Gasket
238
650932
Screw, 10-32 x 49164"
239 34338
Air Cleaner Gasket
241
36919
Air Cleaner Collar
245
36905
Air Cleaner Filter
250
36920
Air Cleaner Cover
260 37180
Blower Housing
261
30063
Screw, Torx T-30,
t/4-20 x 112"
262 650831
Screw, 114-20 x 1/2"
Qty.
1
1
2
1
1
4
2
2
1
1
I
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
2
item
263A
266
266A
275
276
277
279
Part#
Qty.
Starter Grill
1
Stud, 1/4-20
1
Nut E Lockwasher, 114-20 1
Muffler (IncL 276 &. 277)
1
Locking Plate
1
Screw, 114-20 x 2-47/64"
2
Screw, Torx T-25,
10-32 x 5t8"
I
Heat Shield
1
280 37210
285 3500QA
Starter Cup
1
287 650926
Screw, 8-32 x 21164"
2
290 29774
Fuel Line
1
292 26460
Fuel Line Clamp
2
298
28763
Screw, 10-32 x 35/64"
2
300
36916
Fuel Tank (Incl. 292 & 301) 1
301
36246
Fuel Cap
1
305 35647
Oil Fill Tube
1
306
36996
"0"-Ring
1
3O7 35499
"0"-Ring
1
309 650562
Screw, 10-32 x 1/2"
1
310
35648
Dipstick
1
313
34080
Spacer
1
325
29443
Spring Clip
t
341A 36578
Blower Housing
Support Bracket
1
347
651038
Screw, 10-32 x 27/32"
i
370A 36261
Lubrication Decal
2
370B 35169
Control Decal
1
380 640147
Carburetor (Incl. 184)
1
390 590739
Rewind Starter
1
(NOTE: This engine could have been built with
590702 starter).
900
0
Replacement Engine
0
900 0
Replacement S/B 750835,
order from 71-999
1
2O
37184
651O40
650852
36950
36949
651039
650431
Description
CRAFTSMAN 2200 PSi HiGH PRESSURE WASHER 580.762200
Craftsman 4=Cycle Engine 143.986714
Item
0
Part#
Description
640147
Carburetor
ncl. 184 of Engine
artsList)
Throttle Shaft & Lever
Assembly
Throttle Return Spring
Dust Seal Washer
Dust Seal (Throttle)
Throttle Shutter
Shutter Screw
Fuel Fitting
Throttle Crack
Screwlldle Speed
Screw
Tension Spring
Idle Restrictor Screw
Idle Restrictor
Screw Cap
631615
2
4
5
6
16
17
631767
631184
631183
640070
650506
631807
651025
18 630766
20 640016
20A 640053
Qty.
item
1
1
1
1
1
1
1
1
i
1
1
1
2]
Part#
Description
25
27
28
29
30
631867
631024
632019
631028
631021
31
35
631022
36045A
36
37
632745
632547
40
44
47
640083
27110
630748
48
631027
Float Bowl
FloatShaft
Float
Float Bowl "0" Ring
Inlet Needle, Seat,
k Clip (Incl. 31)
Spring Clip
Primer Bulb/Retainer
Ring
Main Nozzle Tube
Main Nozzle Tube
"0"Rin-_q " '
High S_eed Bowl Nut
Bowl Nut Washer
Welch Plug, Idle
Mixture VVelt
Welch Plug,
Atmospheric Vent
1
1
1
1
1
1
1
1
2
1
1
I
t
CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200
Craftsman 4-Cycle Engine 143.986714
/
_3
Item
0
3
6
8
11
12
13
14
Part#
Description
590739
590740
590616
590617
590618A
59063B
590535
590701
590741
Rewind Starter
Retainer
Starter Dog
Dog Spring
Pulley k Rewind Spring Ass'y
Starter Housing Ass'y_40 degree grommet)
Starter Rope (I-engti-i98 x 9(64" alia.)
,
Starter Handle
Locking Tab
.
Qty.
22
1
1
2
2
1
1
1
1
1
CRAFTSMAN 2200 PSi HiGH PRESSURE WASHER 580,7622_
Craftsman 4=Cycle Engine 143.986714
13
_8
_3
_5
Item
0
1
2
3
4
5
6
7
8
11
12
13
Qty.
Part#
Description
590702
590599A
590600
590696
590601
590697
590698
590699
590700
590703
590535
590701
Recoil Starter
Spring Pin (Zncl. 4)
Washer
Retainer
Washer
Brake Spring
Starter Dog
Dog Spring
pulley & Rewind Spring Ass'y.
Starter HousingA,ss'y. NO degree grommet)
Starter Rope (98 X 9/64 dia.)
Starter Handle
23
0
1
1
1
1
1
2
2
1
I
1
1
CRAFTSMAN
2200 PSI HIGH PRESSURE
WASHER
580,762200
19
17
tZ
ToA
24
CRAFTSMAN
2200 PSi HiGH PRESSURE
FFEM
1
2
_
NO.
EB2528
132619
1
1
3
4
5
6
7
8
9
A1803C
EB2534
39414
52858
42909
27007
B2142
1
1
3
5
2
2
2
10
11
12
13
t4
15
16
17
!8
19
20
754O2
B2168
B1460
B1779
B2347
46476
51767
52857
92235
B1631A
B2623
2
1
3
2
2
2
2
2
1
1
1
2I
22
23
24
25
B2626
91373
79552
96307
A1040B
t
1
1
1
1
WASHER 580.762200
iTEM
26
27
28
29
30
BASE, VSPW
ENGINE, Tecumseh O1_',/
6.75HP
PUMP, Medium Frame
HANDLE
HHCS, M8 x 35
NUT, M8 Locking Flange
HHCS, M8 x 30
MOUNT, Rubber Foot
WHEEL, 2"x g' Black
Mag
PUSHNUT, i/2"
HANGER, Hose
CAP, Vinyl
COVER, Hinge
CAP, End
CAPLUG
HHCS, M6 - 1.0x 45
NUT, M6 Locking Flange
GROMMET, Turbo Nozzle
BILLBOARD
DECAL, Crafcsman2200
PSI
DECAL, Instructions
DECAL, Data
OVERLAMINATE
DECAL, 1-800 #
HOSE, Chemical
25
PART,NO.
A1041
A1408
B1232
B1288
21782
1
1
i
1
1
31
21781
1
32
33.
35
36
37
38
39
40
41
42
43
44
45
46
50190
48031
97054
97100
B1969
B1974G
B2370
95587E
97123
B2389
88935
97566
B1736
B1736A
2
1
1
1
1
1
1
1
1
1
1
1
1
1
47
48
49
50
96382
B2620
B2730
97009
1
1
1
1
DESCRI_ON
FILTER, ChemicaI Hose
CAP, Garden Hose Inlet
CLAMP, Hose 7/16"
TAG, Breather Cap
QUICK DISCONNECT,
Female
QUICK DISCONNECT,
Mate
WASHER, M8 Flat
CLAMP, Hose 3/t6"
TAG, Pressure Adjust
CAP, High Pressure
HOSE, 1/4" x 25'
TURBO, Nozzle
GUN, High Pressure
NOZZLE, Adjustable
WAND, Extension
BRUSH, Rotating
ADAPTER, Brush
TAG, Nozzle
WASH, VehideJBoat
WASH, HouseJMuHJ
Purpose
OIL, Engine SAE 30
MANUAL, Owners
KIT, O-Ring Maintenance
KIT, Nozzle Cleaning
CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200
_J
>
26
CRAFTSMAN 2200 PSi HIGH PRESSURE WASHER 580.762200
item
Part #
Qty,
1
2
3
93871
96430A
96542
I
1
1
4
5
6
7
8
9
!0
11
97675
97570
95524
92479
95531
95435
97671V
97606
1
1
t
4
4
1
1
1
t2
93790
13
14
15
16
17
18
19
20
21
23
97568A
96400
99427
94944
99735
93680
93668
93667
93652
95416
93876
I
3
3
3
1
3
3
3
1
1
1
24
25
26
27
28
29
30
31
A1320
93873
40945
A2069
A2062
A2060
97931
97934
1
6
6
1
3
6
3
6
32
33
34
35
97929
97843
A2017
A17t9
6
1
2
1
Description
item
Part #
Qty.
GASKET,EngineAdapter
ADAPTER,Eng_e
BEARING,Eng,Adptr.Ro!ter
Thrust4x4
36
37
38
A1711
93656
A3829
I
1
1
SPINDLE,PressureRegulator
"O"RING,Spind_114x 3/8x 1/16cs
"O"RING,RetainerNut 14 x 17.56x
1.78
39
40
41
42
43
44
A 1712
A 1716
A2016
A2039
A2013
97840
1
1
1
1
_,q', Retainer-S#nd_
SPRING,Unloader
PAR-BACK,BackupRing
HANDLE,Unloader
6
3
45
46
47
97841
20002
A3805
3
3
1
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
73
74
A2217
A1318
B1758
96053
96015
A1717
B1757
A1718
93644
95380
95379
A1575
97855
A17!3
A2015
A2503
A2756
89138
2112 3
A1714
B2236
132241
B2665
95441
3
1
1
3
3
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
t
6
1
C - RING,Cam Retainer
WASHER,Thrust
WASHER,Ret_ner
LOCKWASHER,M8 Ribbed
BOLT,SHC5/16- 24 x 3/4"Lg
ADAPTER,EngineShaft3/4"
CAM,Axial6.0 U_
BEARING,Axial CamRoller
Thrust5.5x 4
"O_RING,Crankcase
113.97
x 119.21x2.62
CRANKCASE,Pump
SPRING,PistonReturn
ASSEMBLY,CeramicPiston& Cap
SHOE,PistonPivot
ASSEMBLY,Bre_lher
SEAL,Oil P_on
SPACER,P_!ot
SEAL,U- Cup ELF
SPRING,ThermalRer_fActuator
PISTON,_
RetiefAc_._,tor
=(7'RING,Them_ Relief
2.gx6.5x 1.78
SPACER,InletPlate
LOCKWASHER,M6 Ribbed
SCREW,SHC M6x 1.0x 20 mm Lg
GASKET,Head
SEAT,CheckValveInlet
POPPET,CheckValve
CAGE,CheckVa_ Inlet
"O"RING,Chk Valve1Z4 x 15.96x
1.78
SPRING_
CheckValveOutlet
=O"RING,9.25x 12.81x 1.78
PAR-BACK,BackupRing
PIN,2.0Dia.Spindle
2?
Description
BOLT,HeadM8 x 125 x 70ramLg
=O"RING,ChkValvecap15.6x 19.16x
1.78
CAP,OutletPort
CAGE,CheckValve
=O"RING, Venturi 10.82 x 14.38 ×
1.78
SEAT,CheckValveOultet
CYLINDER,Head
PLUG, Bulton M8 x 1.25 x 8 mm
SEAL,HighPressure
RING,Bearing
MAGNET,BaitDeflector
_
ButtonM6x l_)x8mm
SET SCREW, M8 - 1.25 x 8 mm
ACTUATOR,Themla!Relief
SPRING,Chemica!Injector
BALL 5.5dia.Chernk_lInjector
BARBHOSE,BrasswithNylonInsert
"O" RING,BaitSeat6.5x t0.5 x 2 cs
SEAT,BallUnloader
BALL, Stainless Steel 9/32 I_ia.
SEAT, Trapped Line Pressure
VALVE, ShuttlePiston
SPRING, Check Valve
"O" RING, 3.68 x 7.24 x 1.78 cs
VENTURI, Chemical
LOCKNUT, M6 x 1.0 Nylon
CAP, Plastic
WASHER
PILOT, Engine
For the repair or replacement parts you
need delivered directly to your home
Call 7 a.m. - 7 p.m., 7 days a week
1-800-366-PART
(t-800-366-7278)
For in-home
major
brand repair service
Call 24 hours a day, 7 days a week
1-800-4-REPAIR
(1-800=473-7247)
For the location of a Sears Parts and
Repair Center in your area ........
Call 24 hours a day, 7 daysa week
1 =800-488=1222
For information on purchasing a Sears
Maintenance Agreement or to inquire
about an existing agreement
Call 9 a.m. - 5 p.m., Monday-Saturday
1-800=827-6655
The model number of your product is on a
decal attached to the pressure washer.
The model number of the engine is located
on the blower housing of the engine.
When requesting service or ordering parts,
always provide the following information:
, Product Type
• Model Number
• Part Number
. Part Description
America's
Repair Specialists