Samsung ML-1650 Specifications

LASER PRINTER
ML-1650Series
ML-1650 / ML-1651N
SERVICE
LASER PRINTER
Manual
CONTENTS
1. Precautions
2. Specifications
3. Disassembly and Reassembly
4. Troubleshooting
5. Exploded Views and Parts List
6. Block Diagram
7. Connection Diagram
This service manual is also provided on the web,
the ITSELF system f Samsung Electronics Co., Ltd.
“http://itself.sec.samsung.co.kr”
© Samsung Electronics Co.,Ltd. September 2001
Printed in Korea.
VERSION NO. : 2.00
CODE : JC-0055A
This manual is stated and
provided for service description.
All rights reserved. Any parts of the
information in this manual are prohibited
from free duplication, use or translation
without prior written approval except in
cases allowed by the Copyright Act.
Specifications are subject to change without
prior notice.
Samsung Electronics Digital Printing CS Group
Copyright (c) 2001. 6.
Precautions
1. Precautions
Please read the following carefully to prevent any accidents and not to damage the unit during service.
1-1 Safety Precautions
Read each caution carefully:
1. Do not use this printer near water or when exposed to
inclement weather.
2. Do not place this printer on an unstable cart, stand or
table; the product may fall, causing serious damage
to the product.
3. Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation and to protect
the printer from ever heating, do not block or cover
any of these openings. Do not place the printer in an
enclosure unless the enclosure provides adequate
ventilation.
4. Never push objects of any kind into the printer through
the cabinet ventilation slots as they may touch dangerous high voltage points, create short circuits,
cause a fire, or produce an electrical shock. Never
spill liquid of any kind on the printer.
5. Do not place the printer in a location where someone
may trip on the cords.
6. Select a work surface that is large enough to hold the
printer.
7. Position the printer within six feet of the computer and
within five feet of an electrical outlet.
8. Operate this printer using the power source (110V,
220V, etc) indicated on the marking label. If you are
not sure of the type of power source available, consult
your dealer or local power company.
9. If you need to use an extension power cord with this
printer, make sure that it uses a three-wire grounded
cord and that the total ampere ratings for all of the
products using the extension do not exceed the
extension cord ampere rating. Also, make sure that
the total of all products plugged into the wall outlet
does not exceed 15 amperes.
10. Do not allow anything to rest on the power cord or
data communications cable.
11. Unplug this printer from the wall outlet before cleaning. Do not use liquid cleaners or aerosol sprays. Use
a damp cloth for cleaning.
12. Do not touch the surface of the photo-sensitive drum
as marks or scratches may impair print quality.
13. Do not expose the drum unit to direct light for prolonged periods.
14. Use only standard papers, OHP films, and approved
envelopes. Feed OHP films though the manual feed
slot only. See specifications for approved papers and
envelopes.
15. Other than replacing consumables such as paper
and toner, refer all questions to qualified service personnel.
Samsung Electronics
Especially mind the safety on the part with
this mark.
You must use regular parts described in specifications for the parts inflammable and where the
current can be flown. Otherwise any hazard
such as an electric shock or a fire could occur.
LASER STATEMENT (LASERTURVALLISUUS)
WARNING : NEVER OPERATE AND SERVICE THE PRINTER
WITH THE PROTECTIVE COVER REMOVED
FROM LASER/SCANNER ASSEMBLY. THE
REFLECTIVE BEAM, ALTHOUGH INVISIBLE, CAN
DAMAGE YOUR EYES.
Class 1 laser product
Luokan 1 laserlaite
Klass 1 laser apparat
Allonpituus 770-795nm
Teho 0.3mW±0.03mW
CAUTION
INVISIBLE LASER RADIATION WHEN
THIS COVER OPEN. DO NOT OPEN
THIS COVER.
VORSICHT
UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GEOFFNET.
NIGHT DEM STRAHL AUSSETZEN.
ATTENTION
REYONNEMENT LASER INVISIBLE EN CAS
D’OUVERTURE. EXPOSITION DANGERUSE AU
FAISCEAU.
ATTENZIONE
RADIAZIONE LASER INVISIBLE IN CASO DI
APERTURA. EVITARE L’ESPOSIZONE LA FASCIO.
PRECAUCION
REDIACION LASER INVISIBLE CUANDO SE
ABRE. EVITAR EXPONERSE AL RAYO.
CAUTION : Avoid exposure to invisible laser radiation when the
development unit is not installed.
1-1
Precautions
1-2 Precautions on Disassembly and Reassembly
Very careful precautions should be taken when replacing
parts. Before replacing, please check cables because
you cannot put the cables that you removed for replacing
parts into the proper place if you would not make sure of
where they were connected and in which condition.
7. When disassembling, assembling, also observe small
components are located in place.
8. If you uncover and turn the machine over to replace
some parts, toner or paper particles may contaminate
the LSU window. Protect the LSU window with clean
paper.
Please do the following before disassembling for a repair
or replacement of parts.
Releasing Plastic Latches
1. Pull out paper cassette, printer cartridge installed.
Especially careful not to be scratched by the surface of
developer or not to expose them to light.
2. Turn the power switch off.
3. Take out the power plug, printer cable from the printer.
4. Use only the same type of part as original when replacing parts.
5. Do not force to open or fasten plastic material components.
6. Be careful that small parts such as screws should not
get in the printer.
1-2
Many of parts are held in
place with plastic latches.
The latches break easily :
release them carefully.
To remove such parts,
press the hook end of the
latch away from the part to
which it is latched.
Samsung Electronics
Precautions
1-3 Tools for Troubleshooting
The following tools are recommended for safe and smooth troubleshooting described in this service manual.
1 DCU(Diagnostic Control Unit)
Standard: Test equipment to diagnose the Laser
printer supplied by Samsung Electronics.
4 Driver
Standard: "-" type, "+" type (M3 long, M3 short,
M2 long, M2 short).
5 Pinset
Standard: For general home use, small type.
2
DVM(Digital Volt Meter)
Standard: Indicates more than 3 digits.
6 Cotton Swab
Standard: For general home use, for medical service.
Ground
Equipments a IPA(Isopropyl
7 Cleaning
Alcohol)dry cloth or a soft stuff neutral
detergent.
3 Electronic Scale
8 Software(Driver) installation CD ROM
Standard: Equipment to check the weight of consumables(toner cartridge) supplied by Samsung
Electronics. (The gram unit can be measured.)
Note
Samsung Electronics
Mind your hands not to be touched when
you disassemble and reassemble PBA ASS'Y,
such as the main board, SMPS, HVPS.
1-3
Specifications
2. Specifications
ML-1650
Engine
Speed
ML-1651N
17 PPM(Letter) , 16PPM(A4)
Resolution
1200 * 1200
First Print Time
Tray 1 : Less than 14 seconds
Tray 2 : Less than 17 seconds
Warm-Up Time
Less than 40 seconds
Power Consump.
Print : 300 W, Sleep mode : Less than 20 W
Dimension(W * D * H)
361 x 409 x 294.5 mm
Weight
12.4 Kg/27.3lb (SET)
Acoustic Noice
Stand by : Less than 35 dB, Operating : Less than 49dB
Power Rating
AC 100~127V , 50 Hz
AC 220~240V , 60 Hz
Controller
Processor
Memory
Power PC (166 MHz)
Standard : 16Mbyte
RAM
Option DIMM Module ; 16, 32,64,128M byte
ROM
4 Mbyte (16M bit x 2 : Program) Flash Memory
512 bytes
EEPROM
Emulation
PCL6, PS 3(Option)
Interface
IEEE1284, USB, Network
OS Support
Windows 95/98/2000/Me/NT,
Linux(Radhat 6.0 ↑), iMac(Mac OS 8.0 ↑)
N/W
Paper
Input
Option
Default
Cassette
550 sheets (75g/m2)
MP Tray
100 sheets (75g/m2)
20 sheets (OHP)
10 sheets (Letter, card)
25 sheets (Label)
Output
Media Type
Face down
250 sheets
Face up
100 sheets
A4, Letter. Legal, Executive, B5, A5, Folio, 7 3/4(Monarch),
#10, DL, C5, C6, B5
Toner
User interface
Type
Single Cartridge
Life
8,000 sheets (Set : 4,000 sheets)
Cartridge
8,000 sheets (Set : 4,000 sheets)
Pick up Roller
60,000 sheets
Feed Roller
60,000 sheets
Transfer Roller
125,000 sheets
Fuser
40,000 sheets
Key & LED
3Key, 4LEDs
LCD
Toner Save
Reprint
Samsung Electronics
No
YES
YES(Button)
2-1
Specifications
ML-1650
Environment
Operation Environment Temperature
Storage Environment
10 ~32˚c (50˚F ~ 90˚F)
Humidity
20 ~ 80 % RH
Temperature
-200 ~40˚c (4˚F ~ 104˚F)
Humidity
10 ~90 % RH
Network Operating Systems
ML-1651N
Windows 95/98 and Windows NT (3.51, 4.x )
Netware (3.x, 4.x), NDS and Bindery Mode /RPRINT,
PSERVER Mode
UNIX and Apple Talk
Network
Network Protocols Supported
TCP/IP : Windows 95/98, Windows NT, UNIX
IPX/SPX : Windows 95/98, Novell Netware
DLC/LLC : Windows 95/98, Windows NT
Ethertalk : Apple Talk
SNMP : for Network Printer Administration
Network Card Interface
Ethernet 10/100 BaseTX (Auto Negotiation)
Network Management S/W
Samsung’s Admin. Software Utility (SyncThru)
SNMP and MIB-II Support,
GUI based utility for Windows Systems and Test based
utility for UNIX Systems
HTTP server for web browser based network management (can manage NPC and printer options on Web
Browser)
2-2
Samsung Electronics
Disassembly and Reassembly
3. Disassembly and Reassembly
3-1 General Precautions on Disassembly
When you disassemble and reassemble components, you must use extreme caution. The close proximity of
cables to moving parts makes proper routing a must. If components are removed, any cables disturbed by
the procedure must be restored as close as possible to their original positions. Before removing any
component from the machine, note the cable routing that will be affected.
Whenever servicing the machine, you must perform as follows:
1. Remove the paper cassette(s), and the print cartridge. Do not expose the cartridge to direct room light or
sun light, and be careful not to scratch the drum surface.
2. Turn the power switch off.
3. Unplug all the cables from the printer.
4. Replace with only an authorized component.
5. Do not force to open or fasten a plastic material component.
6. Be careful no obstacles are included when you reassemble components.
7. When you reassemble components, be careful small size components are located in place.
8. If you turn the machine over to replace some parts, toner or paper particles may contaminate the LSU
window. Protect the LSU window with clean paper.
Releasing Plastic Latches
Many of the parts are held in place with plastic latches.
The latches break easily; release them carefully.
To remove such parts, press the hook end of the latch away from
the part to which it is latched.
Samsung Electronics
3-1
Disassembly and Reassembly
3-2 Transfer Roller
1. Open the printer cover.
3. Hold the cap at the both end of the roller, then
remove the roller.
2. Remove the cap.
3-2
Samsung Electronics
Disassembly and Reassembly
3-3 Controller Board
1. Remove two screws and remove the
controller cover.
Samsung Electronics
2. Remove five screws securing the board and
unplug all connectors, and then take the
controller board out of the printer.
3-3
Disassembly and Reassembly
3-4 Pickup Assembly
1. Turn the printer upside down. Remove four
screws, then remove the bar cross bottom.
4. Take the assembly out.
Push the solenoid if
you have difficulty to
remove the pickup
assembly.
2. Remove three screws from the left base
bracket, and take the bracket out.
5. Check the pickup rubber wear. If the rubber is
heavily worn, replace it with a new one.
3. Remove four screws securing the pickup
assembly.
Squeeze this tab to
remove the rubber.
3-4
Samsung Electronics
Disassembly and Reassembly
3-5 Main Cover
1. Remove two screws and remove the controller
cover.
4. Remove two screws securing the main cover.
2. Remove two screws at the back of the printer and
unplug one connector from the board, then open
the rear cover.
5. Unlatch the front ends of the cover.
3. Open the printer cover, and open the MP tray.
|6. Slide the main cover upward, out of the printer.
Note that the power
switch and the power
connecter are properly
released when you
remove the cover.
Samsung Electronics
3-5
Disassembly and Reassembly
3-6 MP (Multi-Purpose) Tray
1. Before you remove the MP tray, you should remove:
-Main Cover (see page 3-5)
2. Remove the stoppers securing the MP tray.
3-7 Exit Assembly
1. Before you remove the exit assembly, you
should remove:
3. If you want to remove the roller shaft, unlatch
both ends of the shaft and take it out.
-Main Cover (see page 3-5)
2. Remove the exit tray in the direction of arrow.
4. If you want to remove the exit roller, squeeze
the bottom of the roller and take it out.
3-6
Samsung Electronics
Disassembly and Reassembly
3-8 LSU
1. Before you remove the LSU, you should remove:
-Main Cover (see page 3-5)
-Exit assembly (see page 3-7)
2. Remove five screws, and remove the LSU. Then
unplug two connectors from the LSU.
3-9 HVPS board
1. Before you remove the HVPS board, you
should remove:
-Main Cover (see page 3-5)
2. Remove four screws and take the HVPS
board out.
Samsung Electronics
3-7
Disassembly and Reassembly
3-10 Fan
1. Before you remove the fan, you should remove:
-Main Cover (see page 3-5)
3. Remove one screw, and remove the fan.
Then unplug one connector.
2. Remove two screws securing the connector
cover and harness bracket from the gear
bracket.
3-11 Solenoid
1. Before you remove the solenoid, you should
remove:
-Main Cover (see page 3-5)
2. Remove two screws, and remove the
solenoid. Then unplug one connector.
3-8
Samsung Electronics
Disassembly and Reassembly
3-12 Drive Assembly
1. Before you remove the drive assembly, you
should remove:
-Main Cover
-Fan
(see page 3-5)
(see page 3-9)
4. If you want to remove the step motor, remove
four screws securing the step motor from the
motor bracket and unplug two connector from
the motor.
2. Remove four screws securing the drive
assembly from the gear bracket and unplug
one connector from the motor, and then take
the drive assembly out.
3. If you want to remove the motor assembly from
the drive assembly, remove five screws
securing the motor assembly to the gear
bracket.
Samsung Electronics
5. If you want to remove the motor joint PCB,
remove two screws securing the motor joint
PCB from the gear bracket and unplug one
connector from the motor joint PCB.
3-9
Disassembly and Reassembly
3-13 Fuser Assembly
1. Before you remove the fuser, you should remove:
♦ To remove the thermistor from the fuser
assembly :
-Main Cover (see page 3-5)
Remove one screw, and release the wire from the
three holders, and then take the thermistor out.
2. Remove four screws and unplug one connector, and then remove the fuser assembly.
♦ To remove the thermostat from the fuser
assembly
♦ To remove the halogen lamp from the fuser
assembly :
Remove two screws and take the thermostat out.
Remove two screws and take the halogen lamp
out of the fuser assembly.
Note
3-10
When you reassemble the halogen
lamp, make sure that it is inserted into
the slot properly.
Samsung Electronics
Disassembly and Reassembly
3-14 Guide Feed & Erase Lamp
1. Before you remove the guide feed & PTL, you
should remove:
4. Remove the guide feed& erase PTL.
-Main Cover (see page 3-5)
2. Release the latches on the erase lamp from the MPF
ASS’Y and unplug one connector, then remove the
PTL.
3. Remove three screws and raise the guide feed in the
direction of arrow.
Samsung Electronics
3-11
Disassembly and Reassembly
3-15 MPF Assembly and Miscellaneous on MPF Assembly
1. Before you remove the MPF assembly, you
should remove:
-Main Cover (see page 3-5)
♦ To replace the nockup plate :
1. Turn the gear shown in the square in the
direction of arrow to release the nockup plate.
2. Unplug two connectors and remove five
screws, and then take the MPF assembly out.
2. Remove the spring , then release the right end
of the plate.
♦ To replace the pickup roller :
1. Remove the e-ring.
3. Remove the nockup plate.
2. Remove the roller.
3-12
Samsung Electronics
Disassembly and Reassembly
♦ To replace the Paper Empty (PE) sensor :
♦ To replace the pickup holder and the Adjust
End MP:
1. Release the wire from the two holders.
1. Remove two screws and remove the MPT
bracket.
2. Raise the pickup holder in the direction of
arrow.
2. Unlatch the PE sensor, then take it out.
3. Remove the pickup holder.
4. Remove the Adjust End MP
Samsung Electronics
3-13
Disassembly and Reassembly
3-16 Engine Board and Miscellaneous
1. Before you remove the engine board, you should
remove:
4. While you push the latch to release the PCU shield,
take the PCU shield out of the printer.
-Main Cover (see page 3-5)
2. Remove six screws from the left and the right base
bracket and take them out.
3. Remove eight screws securing the PCU shield and
remove two screws securing the SCF connector, and
then take the PCU shield out of the printer.
3-14
5. Unplug all connectors from the PCU shield, and
remove the shield.
Samsung Electronics
Disassembly and Reassembly
♦ To replace the exit board :
Unplug one connector from the controller board
and remove one screw securing the board.
Then release the wire from two holders and
take the board out.
♦ To replace the fuser sensor :
Remove two screws and take it out.
Samsung Electronics
♦ To replace the Cap sensor :
Remove two screws and take it out.
♦ To replace the actuator empty :
Take the sensor out while you squeeze the both
ends of the sensor.
3-15
Disassembly and Reassembly
♦ To replace the actuator feed
1. Turn the mechanism back and push down the
points as shown to unlatch the actuator feed.
♦ To remove the transfer guide :
Remove three screws and take the guide out.
2. Turn the unit over again, and remove the
actuator feed.
3-16
Samsung Electronics
Troubleshooting
4. Troubleshooting
4-1 How to use DCU
4-4 The cause and solution of the malfunction
4-1-1 DCU Setup ......................................Page(4-2)
4-4-1 All LEDs blinking (Fuser Error)........Page(4-17)
4-1-2 Code ................................................Page(4-2)
4-4-2 All LEDs blinking (SCAN ERROR) .Page(4-17)
4-1-3 Self Diagnostic Mode......................Page(4-3)
4-1-4 Self Test Button ................................Page(4-4)
4-4-3 Not function of the gear of the fuser due to
melting away.....................................Page(4-18)
4-1-5 Paper Path Layout ...........................Page(4-4)
4-4-4 Paper Empty.....................................Page(4-18)
4-1-6 DCU Panel .......................................Page(4-5)
4-4-5 Paper Empty without indication.......Page(4-18)
4-4-6 Cover Open ......................................Page(4-19)
4-2 The cause and solution of Bad image
4-2-1 Vertical Black Line and Band ..........Page(4-6)
4-2-2 Vertical White Line ...........................Page(4-6)
4-2-3 Horizontal Black Band .....................Page(4-7)
4-2-4 Black/White Spot..............................Page(4-7)
4-4-7 No lamp on when the cover is open
...........................................................Page(4-19)
4-4-8 Defective motor operation ...............Page(4-20)
4-4-9 No Power..........................................Page(4-20)
4-4-10 Vertical Line Getting Curved .........Page(4-21)
4-2-5 Light Image.......................................Page(4-8)
4-2-6 Dark Image or a Black.....................Page(4-8)
4-2-7 Uneven Density................................Page(4-9)
4-2-8 Background ......................................Page(4-9)
4-2-9 Ghost (1)...........................................Page(4-10)
4-2-10 Ghost (2)..........................................Page(4-10)
4-2-11 Ghost (3) ..........................................Page(4-11)
4-2-12 Ghost (4) .........................................Page(4-11)
4-2-13 Satins on the Face of Page............Page(4-11)
4-5 Toner Cartridge Service
4-5-1 Precautions on Safe-keeping of Toner Cartridge
..........................................................Page(4-22)
4-5-2 Service for the Life of Toner Cartridge
..........................................................Page(4-22)
4-5-3 Service for Judgement of Inferior Expendables
and the Standard of Guarantee .....Page(4-22)
4-5-4 Signs and Measures at Poor toner cartridge
..........................................................Page(4-23)
4-2-14 Satins on Back of Page..................Page(4-12)
4-2-15 Blank Page Print out (1) .................Page(4-12)
4-2-16 Blank Page Print out (2) .................Page(4-12)
4-6 The cause and solutions of bad environment
of the software
4-6-1 The printer is not working (1)...........Page(4-26)
4-3 The cause and solution of the bad discharge
4-6-2 The printer is not working (2) .........Page(4-27)
4-3-1 Wrong Print Position .......................Page(4-13)
4-6-3 Abnormal Printing.............................Page(4-28)
4-3-2 JAM 0...............................................Page(4-13)
4-6-4 SPOOL Error ...................................Page(4-29)
4-3-3 JAM 1...............................................Page(4-14)
4-3-4 JAM 2...............................................Page(4-14)
4-3-5 Multi-Feeding...................................Page(4-15)
4-3-6 Paper rolled in the fuser .................Page(4-15)
4-3-7 OPC .................................................Page(4-16)
Samsung Electronics
4-1
Troubleshooting
4-1 How to use DCU
4-1-1 DCU Setup
You can examine the malfunction of the printer. To perform DCU, open the front discharge cover and leave the connect
the harness wire(10 pin/4 pin) to the CN10(4 pin) of the Main control board.
4-1-2 Code
Connect DCU to the printer and turn the power on. It show 7 LED on the panel and each code tells the function of the
printer.
Normal Code
While printing or warming up, it indicate the position of the paper
61
00-05
Warm up
Ready(kind of paper)
20, 21, 22 Print Start
30
40
50
69
Feed Sensor On
Feed Sensor off
Paper Out
Sleep Mode
The printer is on, the cover is open or close.
The printer is ready, the paper is detected when the first paper is printed.
00: Legal ,01: Letter ,02: A4 ,03: EXEC ,04: B5 ,05: Folio, 06: A5/A6
The engine controller received the print order from the video controller.
20: 1st, 21: MP, 22: SCF
The paper is passing out of the Feed Sensor.
The paper has passed out of the Feed Sensor.
The paper has passed out of Exit Sensor.
The fuser power turned off to minimize the power consumption.
Error Code
When detecting the malfunction, the printing is stopped to indicate error code.
60, 62, 68
Fuser Error
64
65
70
71
72
73
76
95
Cover Open
CRU Error
No Paper
Paper Jam 0
Paper Jam 1
Paper Jam 2
Out Bin Full
LSU Not Ready
4-2
The error in the fuser occurred. There is a short circuit in the thermistor and the
thermostat while printing, Low Temperature Error occurs.
• 60: Open Fuser Error
• 62: Low Heat Error
• 68: Over Heat Error
The Printer Cover is open.
The Toner Cartridge not installed,
No paper in the paper cassette.
The front part of paper is jammed between pickup unit and Feed sensor.
The front part of paper is jammed between the Discharge sensor and Feed sensor.
The front part of paper is jammed just after passing through the discharge sensor.
The Out bin is filled with paper.
LSU Scanner Motor not ready or Hsync signal not output.
Samsung Electronics
Troubleshooting
4-1-3 Self Diagnostic Mode
If Error code occurs due to malfunction of the printer, perform Self Diagnostic Mode to solve the problem.
The printer works only in the self-test mode to solve the malfunction problem.
To enter the self-test mode, turn the power on pressing the buttons of [Down], [Shift] and [Stop] at the same time.
Release the button within 2 or 3 seconds if 78 shows in the DCU. If 00 shows in the DCU, press the button [Up] or [Shift]
to select the self+test , and press the button of [Enter] to operate. To stop, press the button of [shift] and [Enter] together.
00
Main Motor Operating System
Only the main motor is in operation.
01
Main High Voltage On(THV-)
-1400 voltage output by MHV terminal.
02
Transfer High Voltage(-)On(THV-)
-1000 voltage output by MHV terminal.
03
Caution : High voltage probe should be used.
Transfer High Voltage (+)Reference on (THV +)
+800 voltage output by MHV terminal.
04
Caution : High voltage probe should be used.
Caution : High voltage probe should be used.
DEV/supply High Voltage : DEV/Supply High Voltage Test.
The left one of the three LEDs in the self-test panel is on when DEV high voltage Supply high voltage output
by each HV terminal(-500V). Press the [Up] button to switch the voltage. The middle and right one of the three
LEDs are on and -650 voltage output by DEV HV terminal.
Caution : High voltage probe should be used.
05
LSU Operating System
The scanning motor of LSU is in operation, the right LED of the three buttons on. Press the [Up] button to
Check LD. LD is functioning and the middle button is on. If the LD is normal, all LEDs are on.
06
Pickup clutch on
The Solenoid in the printer is in operation. To stop the operation, Press the button [shift] and [Enter] together.
07
Paper Empty(1st, SCF, MF) Sensor Test :
If activate the Actuator of the PEMPTY/PWIDTH Sensor, the left and right of the three LEDs are on.
Paper Empty Sensor (1st) ON/OFF
Paper Empty Sensor (SCF) ON/OFF
Paper Empty Sensor (MP) ON/OFF
Increment DCU Code No. (08, Sensor TEST)
08
1st LED ON/OFF
2nd LED ON/OFF
3rd LED ON/OFF
Feed & Exit Sensor Test
Test the Feed sensor and Discharge sensor in the same way as '06'.
09
Cover Open Sensor Test
The same way as code '06'.
10
Fuser Test
If the [Enter] button pressed, the right LED is on and temperature of the fuser is up to READY Mode. If the
[Up] button pressed, the middle LED is on and temperature of the fuser is up to Printing Mode.
If you press the button once more, the left LED is on and temperature of the fuser is up to overheat Mode.
11
Hot Burn Test
If the [enter] button pressed, the printer is continuously printing without detection.
Turn the power off to stop operation.
12
Cleaning Mode Print Mode
Print the paper to clean the OPC Drum in the Cartridge.
Samsung Electronics
4-3
Troubleshooting
13
THV(+) TRIGGER. ALL HV :
All high voltage output by each HV terminal and LSU and the fan is in operation. In this mode, electronic
resistance of transfer roller and high voltage is detected.
14
+7P Clutch Test :
Same method of the code ‘06’.
15
Fan Test :
Indicates the function of the fan, same method of the code ‘06’.
16
Paper size Sensor Test :
Cassette Sensor 1 ON/OFF
Cassette Sensor 2 ON/OFF
Cassette Sensor 3 ON/OFF
Increment DCU Code No. (00,MAIN MOTOR TEST)
Decrement DCU Code No. (15, FAN TEST)
17
1st LED ON/OFF
2nd LED ON/OFF
3rd LED ON/OFF
SMD Test :
This function is for a manufacturing process. You can test all diagnostic Codes(0~06).
When you push the ‘Enter’ button, the main motor runs (Diagnostic Code 00).
If you push the ‘up’ botton, the current diagnostic Code stops, and the next diagnostic Code starts.
4-1-4 Self Test Button
If the Self-Test button pressed, vertical lines are printed.
Turn the power on while pressing this button, '89' shows in the DCU and the printer is warming up. After warming-up the
printer is in READY Mode, and '88' shows in the DCU. In this mode, without any detection, the printer begins
printing(trial printing and data from the PC). It is convenient to use this mode when the engine malfunction is detected in
the control board.
4-1-5 Paper Path Layout
EXIT2
OUT BIN FULL SEN
FACE DOWN
LSU
FACE UP
CARTRIDGE
FUSER
PTL
CR
H/R
FEED SEN
DR
SR
EXIT1
IDLE
OPC
EXIT SEN
Pr/R
MPF
FEED
TR
PICK UP
EMPTY SEN
CASSETTE
SCF
4-4
Samsung Electronics
Troubleshooting
4-1-6 DCU Panel
ML-1650 DIAGNOSTIC CONTROL UNIT
QUICK REFERANCE
04 BIAS 3
BIAS 1
BIAS 0
05 LSU READY
LSU MT&LD
LSU MOTOR
07 PAPER EMPTY SCF
MP
SELF
08 CRU
FEED SENSOR
TEST
EXIT SENSOR
09 COVER OPEN COVER COVER OUT BIN
STATUS
10 COER HEAT
DIAGNOSTIC
ON
DIAGNOSTIC CODE
PRINT HEAT
STANDBY HEAT
OFF
STATUS CODE
00
01
02
03
04
05
06
07
08
09
10
11
MAIN MOTOR OPERATION
MAIN HIGH VOLTAGE ON
TRNSFER HIGH VOLTAGE (-)ON
THV(+) REFERANCE VOLTAGE
DEV/SUPPLY VOLTAGE ON
LSU OPERATING TEST
PICKUP CLUTC ON
PAPER EMPTY SENSOR TEST
FEED & EXIT SENSOR TEST
COVER OPEN SENSOR TEST
FUSER TEST
HOT BURN TEST
12
CLEAN (MESSAGE)PRINT
13
THV(+)TRIGGER &THV ON
14
MP PICKUP ON
15
FAN TEST
16
PAPER SIZE SENSOR TEST
17
SMD TEST
00
01
02
03
04
05
06
READY (REGAL)
READY (LETTER)
READY (A4)
READY (EXECUTIVE)
READY (B5)
READY (FOLIO)
READY (A5,A6)
20
21
22
40
50
PRINT START (1'st CASSETTE)
PRINT START (MP)
PRINT START (2'nd CASSETTE)
FEED SENSOR 2'st ON
PAPER OUT
60 OPEN FUSER ERROR
62 LOW HEAT ERROR
68 OVERHEAT ERROR
GREEN STATUS CODE
88
99
61
64
65
69
70
71
72
73
76
90
WARM UP
COVER OPEN ERROR
CRU ERROR
SLEEP MODE
NO PAPERR or CASSETTE
PAPER JAM 0
PAPER JAM 1
PAPER JAM 2
OUTBIN FULL ERROR
MANUAL PRINT MODE
95 LSU NOT READY
DCU MODE!!
!!!
DOWN!!
UP!!!!
SHIFT!!
STOP
ENTER
O ENTER DIAGNOSTIC MODE, PUSH THREE BUTTONS SIMUL ANEOUSL
THE PRINTER POWER ON.
Samsung Electronics
4-5
Troubleshooting
4-2 The cause and solution of Bad image
4-2-1 Vertical Black Line and Band
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Straight thin black vertical line occurs in the printing.
2. Dark black vertical band occur in the printing.
Check and Cause
Solution
1. Damaged develop roller in the Developer.
Deformed Doctor-blade or cleaningblade.
1. If causes 1 and 2 occur in the developer
cartridge, replace the developer and try to
print out.
2. Scratched surface of the discharge roller
in the developer.
2. Replace the transfer roller if occurred as
No. 3.
3. Partly depression or deformation on the
surface of the transfer roller.
4-2-2 Vertical White Line
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
White vertical voids in the image.
Check and Cause
Solution
1. Foreign matter stuck onto the window of
internal lenses of LSU mirror.
1. Foreign matter stuck onto the window :
Clean the LSU window with recommended cleaner(IPA) Clean the window with a
clean cotton swab.
2. Foreign matter or toner particles between
the developer roller and blade.
(In case the life of the developer has
been expired, white lines or light image
occur in front of the image.)
2. Foreign matter in the LSU : Open the
cover of LSU and clean with a cotton
swab on the surface of the reflex mirror.
3. It may occur when Burr and foreign substances are on the window of the developer frame.
3. No 3. : Remove the foreign matter and
burr of the exposure window.
(Developer cartridge)
4. If the fuser is defective, voids occur periodically at the top of a black image.
4. No. 4. : Open the front cover and check
ribs that corresponds to the position of
the voids. Remove if found.
5. If the problems are not solved, replace
the developer cartridge.
4-6
Samsung Electronics
Troubleshooting
4-2-3 Horizontal Black Band
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Dark or blurry horizontal stripes occur in the printing periodically.
(They may not occur periodically.)
Check and Cause
Solution
1. Bad contacts of the voltage terminals to
developer.
1. Clean each voltage terminal of the Charge,
Supply, Develop and Transfer roller.
(remove the toner particles and paper particles)
2. The rollers of developer may be stained.
Charge roller = 38.5mm
Supply roller = 51mm
Develop roller = 50mm
Transfer roller = 56.8mm
2. Clean the right Gear that has relatively
small gap of the teeth in the OPC.
3. If the malfunction persists, replace the
developer.
4-2-4 Black/White Spot
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Dark or blurry black spots occur periodically in the printing.
2. White spots occur periodically in the printing.
Check and Cause
Solution
1. If dark or blurry black spots occur periodically, the rollers in the Developer may be
contaminated with foreign matte or paper
particles.
( Charge roller : 38.5 mm interval
OPC drum : 96 mm interval)
1. Run OPC cleaning Mode Print and run the
Self-test 2 or 3 times.
2. If faded areas or voids occur in a black
image at intervals of 96 mm, or black
spots occur elsewhere, the OPC drum
surface is damaged.
2. In case of 96 mm interval unremovable in 1,
cleanly remove foreign substances stuck on
the OPC location equivalent to black spots
and white spots with a dry duster.
3. If a black image is partially broken, the
transfer voltage is abnormal or the transfer roller's life has expired.
3. The transfer roller guarantees 125,000
sheets printing. If the roller's life is expired,
replace it.
4. In case of 38.5 mm interval unremovable in
1, take measures as to replace the developer cartridge and try to print out.
5. Clean the inside of the set against the paper
particles and foreign matter in order not to
cause the trouble.
Samsung Electronics
4-7
Troubleshooting
4-2-5 Light Image
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
The printed image is light, with no ghost.
Check and Cause
Solution
1. Develop roller is stained when the toner
of developer cartridge is almost consumed.
1. Check if the Toner Save mode is off.
2. Ambient temperature is below than 10°C.
2. No 1 : Replace the developer cartridge and
try to print out.
3. Bad contact caused by the toner stains
between the high voltage terminal in the
HVPS and the one in the set.
3. No 2 : Wait 30 minutes after printer is powered on before you start printing.
4. Abnormal output from the HVPS.
(Run self-test and check 1~4)
4. No3 : Clean up the contaminated area by
the toner.
5. Replace the HVPS if the problems are not
solved by the above four directions.
4-2-6 Dark Image or a Black
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
The printed image is dark.
Check and Cause
Solution
1. No charge voltage in the engine board.
( Perform DCU diagnostic code 01)
1. Clean the high voltage charge terminal.
2. Charge voltage is not turned on due to
the bad contacts between power supply
in the side of the Developer and charge
terminal of HVPS.
2. Check the state of the connector which
connects the engine board and HVPS.
3. Replace the HVPS if not solved by the
above direction 1 and 2.
4-8
Samsung Electronics
Troubleshooting
4-2-7 Uneven Density
• Description
Print density is uneven between left and right.
Check and Cause
Solution
1. The pressure force on the left and right
springs of the transfer roller is not even,
the springs are damaged, the transfer
roller is improperly installed, or the transfer roller bushing or holder is damaged.
1. Replace both the left and right Spring
Holder.
2. The life of the Developer has expired.
2. Occur in the developer cartridge, replace
the developer and try to print out.
3. The toner level is not even on the developer roller due to the bad blade.
4-2-8 Background
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Samsung Electronics
Light dark background appears in whole area of the printing.
Check and Cause
Solution
1. Recycled recording paper has been
used.
1. B/S is not guaranteed when using recycled
paper.
2. The life of the Developer has expired.
2. Replace the Developer that has expired.
3. The up-to-down movement of the transfer roller is swift?
3. Clean the busing part of the transfer roller.
4. The HVPS is normal?
(Perform DCU diagnostic code 01~04)
4. Replace the Developer if not solved by the
above direction 1~3.
4-9
Troubleshooting
4-2-9 Ghost (1)
• Description
96 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Ghost occurs at 96 mm intervals of the OPC drum in the whole printing.
Check and Cause
Solution
1. Bad contacts caused by contamination
from toner particles between high voltage
terminal in the main body and the electrode of the Developer.
1. Clean the terminals when contaminated by
toner particles.
2. Bad contacts caused by contamination
from toner particles between high voltage
terminal in the main body and the one in
the HVPS board.
2. Occur in the developer cartridge, replace
the developer and try to print out.
3. The life of developer is expired.
3. Replace the engine board if not solved by
the above directions 1-2.
4. Transfer roller lifetime(125,000 sheets)
has expired.
4. If not solved by the direction 3, check the
transfer roller lifetime and replace it.
5. Abnormal low temperature(below 10°C).
5. Wait about 1 hour after power on before
using printer.
6. Damaged cleaning blade in the developer.
6. Occur in the developer cartridge, replace
the developer and try to print out.
4-2-10 Ghost (2)
• Description
4-10
96 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Ghost occurs at 96 mm intervals of the OPC drum in the whole printing.
(When printing on card stock or transparencies using manual feeder)
Check and Cause
Solution
When printing on card stock thicker than normal paper or transparencies such as OHP,
higher transfer voltage is required.
Select 'Thick Mode' on paper type menu from
the software application and after using returning to the original mode is recommended.
Samsung Electronics
Troubleshooting
4-2-11 Ghost (3)
• Description
Check and Cause
Digital
Digital Printer
Printer
Solution
1. The life of the developer may be expired.
1. Occur in the developer cartridge, replace
the developer and try to print out.
2. The abnormal voltage and bad contact of
the terminal of the supply roller
2. Check the approved voltage of the supply
roller and contact of the terminal and adjust
if necessary.
47.1 mm
Digital
Digital Printer
Printer
Digital
Digital Printer
Printer
White ghost occurs in the black image printing at 51mm intervals.
4-2-12 Ghost (4)
• Description
Check and Cause
56.1 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Ghost occurs at 70 mm intervals.
The temperature of the fuser is maintained
high.
Solution
1. Disassemble the fuser and remove the
contaminated toner particles on the roller
and clean the foreign matter between
Thermistor and Heat roller.
(
Caution: can be deformed)
4-2-13 Satins on the Face of Page
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Samsung Electronics
The background on the face of the printed page is stained.
Check and Cause
Solution
1. Toner leakage due to improperly sealed
developer.
1. Replace the developer cartridge.
2. If the transfer roller is contaminated, satins
on the face of page will occur.
2. If the transfer roller is contaminated, run PC
Cleaning Mode Print 2 or 3 times.
And perform Self-Test 2 or 3 times to
remove contamination.
4-11
Troubleshooting
4-2-14 Satins on Back of Page
• Description
Check and Cause
Solution
1. Transfer roller is contaminated.
1. Perform the OPC Cleaning Mode Print 2 or
3 times. Run Self-Test to remove the contamination of the transfer roller.
2. Pressure roller is contaminated.
2. Replace the transfer roller if contaminated
severely.
56.1 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
The back of the page is stained at 56.1 mm intervals.
3. Disassemble the fuser and clean the
H/R(Heat Roller) and P/R(Pressure roller).
And check the area between H/R and
Thermistor. If contaminated, clean the area
not to be deformed.
4-2-15 Blank Page Print out (1)
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Blank page is printed.
Check and Cause
Bad ground contacts in OPC and/or developer.
Solution
Remove contamination of the terminals of the
developer and the unit.
4-2-16 Blank Page Print out (2)
• Description
1. Blank page is printed.
2. One or several blank pages are printed.
3. When the printer turns on, several blank pages print.
Check and Cause
Solution
1. Bad ground contacts in OPC and/or
developer.
1. Remove contamination of the terminals of
the developer.
2. Abnormal solenoid.
2. Perform the engine self test using DCU to check
if the Solenoid is normal.(refer to code 06)
3. If not solved by the above directions 1-2,
Replace the engine board.
4. Turn the power off, delete the data of PC
and try printing again.
4-12
Samsung Electronics
Troubleshooting
4-3 The cause and solution of the bad discharge
4-3-1
Wrong Print Position
• Description
Printing begins at wrong position on the paper.
Check and Cause
Solution
Wrong sense time caused by defective feed sensor
actuator.
Replace the defective actuator
EXIT2
FACE DOWN
OUT BIN FULL SEN
4-3-2LSU JAM 0
FACE UP
CARTRIDGE
FUSER
H/R
FEED SEN
EXIT1
IDLE
MPF
• Description
Pr/R
FEED
TR
PICK UP
EMPTY SEN
1. Paper is not exited from the cassette.
2. Jam-0 occurs if the paper feeds into the printer.
Check and Cause
Solution
1. Check the Solenoid by using DCU
diagnostic mode 06.
1. Replace the solenoid.
2. Check if the pad is loose due to bad
sealing of the side-pad.
2. Replace the side-pad Assembly L or
R, if necessary.
EXIT SEN
CASSETTE
JAM 0
3. Check the surface of the roller-pickup for foreign matter.
4. If continuous clusters occur, check
whether the assembly slot between
shaft-pickup and housing-pickup
become open or is broken away.
3. Clean with soft cloth dampened with
IPA(Isopropyl Alcohol) or water.
4. Replace the Housing-Pickup and/or
Shaft-Pickup.
5. If the paper feeds into the printer
rand Jam 0 occurs, perform DCU to
check feed-sensor of the engine
board.
Samsung Electronics
4-13
Troubleshooting
EXIT2
OUT BIN FULL SEN
FACE DOWN
LSU
FACE UP
CARTRIDGE
FUSER
H/R
4-3-3
JAM 1
EXIT1
IDLE
Pr/R
MPF
FEED
TR
PICK UP
EMPTY SEN
• Description
1. Recording paper is jammed in front of or inside the fuser.
2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the
Actuator-Feed.
Check and Cause
EXIT SEN
EXIT SEN
Solution
1. If the recording paper is jammed in
front of or inside the fuser.
(Perform DCU diagnostic code of)
1. Replace the SMPS.
2. If the recording paper is stuck in the
discharge roller and the fuser just
after passing through the ActuatorFeed, Feed Actuator may be defective.
2. Reassemble the Actuator-Feed and
Spring-Actuator if the returning is bad.
CASSETTE
JAM 1
EXIT2
OUT BIN FULL SEN
FACE DOWN
4-3-4 JAM 2
LSU
FACE UP
CARTRIDGE
FUSER
H/R
MPF
• Description
EXIT1
IDLE
Pr/R
FEED
TR
PICK UP
EMPTY SEN
1. Recording paper is jammed in front of or inside the fuser.
2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the
Actuator-Feed.
EXIT SEN
EXIT SEN
CASSETTE
JAM 2
4-14
Check and Cause
Solution
1. If the paper is completely fed out of
the printer, but Jam 2 occurs : Exit
sensor is defective.
• After the paper is completely discharged, actuator Exit should return
to the original position to shut the
photo-sensor. Sometimes it takes
longer hour than it should and does
not return.
1. Check if the exit sensor actuator is
defective.
• Check if the actuator exit is unformed
(Check if the lever part is unformed
in shape).
• Check whether burrs occur in the
assembly part of the actuator exit or
not and if the actuator is smoothly
operated.
• Check if foreign matters and wire get
caught in the actuator exit's operation.
2. If the paper is rolled in the Fuser Roller:
• This occurs when a Guide claw is
broken away or transformed.
• It occurs when the Spring of a Guide
claw is broken away or transformed.
• It occurs when the Heat-Roller or
Pressure-Roller is seriously contaminated with the toner.
2. If the paper is stuck in the fuser : disassemble the fuser and remove the
jammed paper, and clean the surface
of the pressure roller with dry gauze.
3. Paper is accordion in the fuser.
3. Remove the jammed paper after disassembling the fuser : Clean the surface
of the pressure roller with dry gauze.
• Remove the toner particles stained
on the rib.
• Check the assemblage and performance of the exit.
Samsung Electronics
Troubleshooting
4-3-5 Multi-Feeding
• Description
Multiple sheets of paper are fed at once.
Check and Cause
Solution
1. Solenoid malfunction(the solenoid does not work
properly): Perform DCU mode : solenoid check 06.
1. Replace the solenoid if necessary.
2. Pad-Friction is contaminated with foreign matter.(oil...)
2. Clean the pad friction with soft clothe dampened
with IPA(Isopropyl Alcohol).
3. The face of paper is blended.
3. Use the smooth paper.
4-3-6 Paper rolled in the fuser
• Description
If contaminated at intervals of 57mm on the back of a paper.
Check and Cause
1. Contamination of the pressure roller.
(Background, Hot off set)
Solution
1. Disassemble the fuser, clean the area between the
Heat-roller and Thermistor and remove the foreign
matter of the pressure roller.
2. If background appears badly in the printing, fix it by
referring to the solutions for background.
(See 4-2-8 Background)
Samsung Electronics
4-15
Troubleshooting
4-3-7
OPC
• Description
Paper is rolled up in the OPC.
Check and Cause
Solution
1. Paper is too much thin.
1. Recommend to use normal paper.
2. The face of paper is curled.
2. How to remove the rolled paper in the OPC.
• Remove the paper while turning the OPC against
the ongoing direction.
• Clean fingerprints on the OPC softly with soft
cloth dampened with IPA(Isopropyl Alcohol) or tissue.
4-16
Samsung Electronics
Troubleshooting
4-4 The cause and solution of the malfunction
4-4-1 All LEDs blinking (Fuser Error)
• Description
1. All the lamps on the operator panel blink.
2. Gear of the fuser does not work and breaks away melt away.
When printing, motor breaks away from its place due to defective fuser gear.
Check and Cause
Solution
1. Check if the thermostat, AC wire and Heat Lamp is
open.
1. If the thermostat is open replace the fuser and
check following items.
2. Check if the thermistor sensor is in place.
2. If the thermistor sensor device is located deep in the
sponge, replace the fuser.
3. Check if the heat lamp works properly.
3. Check if the circuit of overheat mode works properly.
4. Check if the overheat circuit works properly.
4. Run DCU mode : Perform DCU diagnostic code 10.
5. The fuser gear is defective due to melting away.
4-4-2 All LEDs blinking (Scan Error)
• Description
1. All lamps on the operator panel blink.
Check and Cause
DCU Mode : Perform DCU diagnostic code 05. If the DCU
error code 95 is displayed, replace LSU.
Solution
Replace LSU.
If you cannot solve the problem after you replace LSU,
replace the main board.
Samsung Electronics
4-17
Troubleshooting
4-4-3 Not function of the gear of the fuser due to melting away
• Description
The motor breaks away from its place due to gear melting away.
Check and Cause
DCU Mode : Check if the Error States '60' '62' '68' occur.
Check the operation of Fuser Erasing Lamp On/Off with
the Error Code Check -10-.
Solution
1. Replace the Fuser.
2. Replace the Main Control board.
4-4-4 Paper Empty
• Description
The paper lamp on the operator panel is on even when paper is loaded in the cassette.
Check and Cause
Solution
1. Bending or deformation of the actuator of the paper sensor.
1. Replace the defective actuator.
2. The function of the engine board is defective Perform
DCU mode: Perform DCU diagnostic code 8.
2. Replace the engine board.
4-4-5 Paper Empty without indication
• Description
The paper lamp on the operator panel does not come on when the paper cassette is empty.
Check and Cause
Solution
1. Bending or deformation of the actuator of the paper sensor.
1. Replace the defective actuator.
2. The function of the engine board is defective Perform.
DCU mode : Perform DCU diagnostic code 8.
2. Replace the engine board.
4-18
Samsung Electronics
Troubleshooting
4-4-6 Cover Open
• Description
The ERROR lamp is on even when the print cover is closed.
Check and Cause
Solution
1. The hook lever in the top cover may be defective.
1. Replace the hook lever, if defective.
2. Check the connector (CN1 : Engine B’d↔HVPS) and
circuit of the cover switch department in the Main Control
board. Perform DCU mode : If Error state '64' occurs,
Check the related codes of the Cover Open Error.
2. Check the insertion of the Cover Open S/W
Connect.
3. Replace the Main Control board or Cover Open
S/W.
Hook Lever
4-4-7 No lamp on when the cover is open
• Description
The ERROR lamp does not come on even when the printer cover is open
Check and Cause
1. Check the connector(CN8) and circuit of the cover switch
department in the Main Control board. Perform DCU
mode : If Error state '64' occurs, Check the related codes
of the Cover Open Error
Solution
1. Check the insertion of the Cover Open S/W
Connect.
2. Replace the Main Control board or Cover Open
S/W.
Samsung Electronics
4-19
Troubleshooting
4-4-8 Defective motor operation
• Description
Main motor is not driving when printing, and paper does not feed into the printer, resulting 'Jam 0'.
Check and Cause
Solution
1. Motor harness or sub PCB may be defective.
1. Check the motor harness, replace it, if defective.
2. Perform DCU diagnostic code 00 and Check the motor
operation.
2. Replace the SMPS, if necessary.
4-4-9 No Power
• Description
When system power is turned on, all lamps on the operator panel do not come on.
Check and Cause
Solution
1. Check if the power input and SMPS output are normal.
1. Replace the power supply cord or SMPS.
2. Check the inferiority of LED-Panel on the front-cover if
the LED of Panel does not appear after normal warmingup.
2. Replace the control board.
3. Replace the LED-panel.
4-20
Samsung Electronics
Troubleshooting
4-4-10 Vertical Line Getting Curved
• Description
When printing, vertical line gets curved.
Check and Cause
1. If the supply of +24v is unstable in the Main Control board
linking with LSU, check drive by DCU Mode: LSU Check
-05- LSU Motor on.
Solution
1. Replace LSU.
2. Replace the Main Control board.
Samsung Electronics
4-21
Troubleshooting
4-5 Toner Cartridge Service
It is not guaranteed for the default caused by using other toner cartridge other than the cartridge supplied by the
Samsung Electronic or caused by non-licensed refill production.
4-5-1 Precautions on Safe-keeping of Toner Cartridge
Excessive exposure to direct light more than a few minutes may cause damage to the cartridge.
4-5-2 Service for the Life of Toner Cartridge
If the printed image is light due to the life of the toner, you can temporarily improve the print quality by redistributing the
toner(Shake the toner cartridge), however, you should replace the toner cartridge to solve the problem thoroughly.
4-5-3 Judgment of a genuine Toner Cartridge
One-way Screw
Genuine Label :
The prevention of
disassembly
4-22
Capacity indication Label
One-way Screw
Samsung Electronics
Troubleshooting
4-5-4 Signs and Measures at Poor toner cartridge
Fault
Light image and
partially blank
image
(The life is ended.)
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Signs
Cause & Check
• The printed image
is light or unclean
and untidy.
1. If the image is light or unclean
and untidy printed image Shake the developer and
then recheck.
• Some part of the
(1)NG: Check the weight of the
image is not printdeveloper
ed.
(2)OK: Lack of toner, so the life
is nearly closed.
• Periodically a noise 2. Some part of image is not
as "tick tick" occurs.
printed - Shake the developer and then recheck.
(1)NG: Check the weight of the
developer and clean
the LSU window with a
cotton swab, then
recheck.
(2)OK: Lack of toner, so the life
is nearly closed.
3. Periodically a noise as "tick
tick" occurs - Measure the
cycle and the weight of the
developer.
4. White vertical stripes on the
whole screen or partly :
Check the weight of the
developer.
Toner
Contamination
• Toner is fallen on
the papers periodically.
• Contaminated with
toner on prints partly or over the whole
surface.
Solution
1. All of 1, 2, 3 aboveIf it become better by shaking,
replace with a new developer
after 50-100 sheets in the closing state of the life span.
2. In case of 2If it becomes better after cleaning the LSU window, then the
developer is normal.
(Because of foreign substance
on the LSU window, the image
has not been printed partly.)
3. In case of 3If the cycle of noise is about 2
seconds, the toner inside the
developer has been nearly
exhausted.( Purchase and
replace with a new developer
after using about 200 sheets at
the point of occurrence)
4. In case of 3This is a phenomenon caused
by lack of toner, so replace with
a new developer.
1. Toner is fallen on the paper
periodically.
(1)Check the cycle of the
falling of the toner.
(2)Check the appearance of
both ends of the developer
OPC drum.
1. If both ends of the OPC drum
are contaminated with toner:
Check the life of the developer.
2.The center of the printed matter is contaminated with toner.
(1)Check whether foreign substances or toner are stuck
to the terminal (contact
point) of the developer.
(2)Check whether the state of
the terminal assembly is
normal.
2. Check whether it could be recycled.
3. If it cannot be recycled:
Replace the developer.
Samsung Electronics
4-23
Troubleshooting
Fault
White Black spot
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Signs
Cause & Check
1. If light or dark periodical black
dots occur, this is because the
developer rollers are contaminated with foreign substance
or paper particles.
• White spots occur
in the image period- (1)38.5mm interval : Charged
roller
ically.
(2)96mm interval : OPC cycle
• Light or dark black
dots on the image
occur periodically.
2. If white spots occur in a black
image at intervals of 96mm, or
black spots occur elsewhere,
the OPC drum is damaged or
foreign substance is stuck to
the surface.
Recycled product
4-24
Solution
1. In case of 1 above Run OPC Cleaning Mode Print
4-5 times repeatedly to remove.
Especially check foreign substance on the OPC surface, then
remove them with a clean gauze
moistened with IPA(Isopropyl
Alcohol) not to damage OPC if
necessary.
Never use usual alcohol.
2. In case of 2
If they are not disappeared by
running OPC Cleaning Mode
Print 4-5 times.
: at intervals of 38.5mm - Replace
the developer.
: at intervals of 96mm - Remove
foreign substance.
: Broken image - Replace the
developer according to carelessness.
3. If a black and white or graphic
image is partially broken at
irregular intervals, the transfer
roller's life has been expired or
the transfer voltage is abnormal.
3. In case of 3 - Exchange the
transfer roller because the life of
the transfer roller in use has been
expired. (Check the transfer voltage and readjust if different.)
• Poor appearance of 1. Poor appearance of the develthe developer.
oper.
(1)Check the damage to label
• Unclean and rough
and whether different materiprintouts.
als are used.
(2)Check the appearance of
• Bad background in
parts of the developer, such
the image.
as frame, hopper.
1. In case of 1 (1)If there is an evidence of disassembling the developer.
(2)If materials other than normal
parts of the developer are
added or substituted.
2. Unclean and rough printouts.
(1)Check whether foreign substance or toner are stuck to
the terminal (contact point) of
the developer.
(2)Check whether the state of
the terminal assembly is normal.
2. In case of 2 - If there are any
abnormals in connection with the
situation of 1.
(1)It occurs when the developer
is recycled over 2 times.
(2)If toner nearly being expired
are collected to use, it is
judged as the recycled developer.
Samsung Electronics
Troubleshooting
Fault
Ghost & Image
Contamination
Signs
Cause & Check
Solution
• The printed image
is too light or dark,
or partially contaminated black.
1. The printed image is too light
or dark, or partially contaminated black.
(1)Check whether foreign substance or toner are stuck to
the terminal(point of contact)
of the developer.
(2)Check whether the terminal
assembly is normal.
1. All of 1, 2, 3 above
(1)Remove toner and foreign substances adhered to the contact
point of the developer.
(2)The contact point of the unit
facing that of the developer
also must be cleaned.
(3)If the terminal assembly is
unsafe:
• Fully stick the terminal to or
reassemble it after disassembling.
• Disassemble the side plate and
push the terminal to be stuck,
then reassemble it.
2. Totally contaminated black.
(Black image printed out)
(1)Check whether foreign substances are stuck to the terminal(point of contact) of the
developer and the state of
assembly.
(Especially check the
charged roller terminal.)
2. In case of 2
It is a phenomenon when the
OPC drum of the developer is not
electrically charged. Clean the
terminals of the charged roller,
then recheck it.
3. The printed image is dark and
ghost occurs.
(1)Check foreign substance
attached to the terminal
(point of contact) of the
developer and the state of
assembly.
(Especially check the developing roller terminal.)
3. In case of 3
It is a phenomenon as the developing bias voltage of the developer. Clean the terminals of the
developing roller, then recheck it.
• Totally contaminatedblack.
(Black image printed out)
• The density of printouts is too dark and
ghost occurs.
Samsung Electronics
4-25
Troubleshooting
4-6 The cause and solutions of bad environment of the software
4-6-1 The printer is not working (1)
• Description
While Power turned on, the printer is not working in the printing mode.
Check and Cause
Solution
1. Run Self-Test Mode: Turn the power on while pressing
the test printing button for 2 or 3 seconds before printing
works.
1.Check the power of the printer and perform the SelfTest. If the test printing works, that means no problems in the printer itself. If the test printing does not
work, that means bad functioning of the printer(not
because of software). Perform DCU to check the
Error Status.
2. Check if the PC and the printer is properly connected
and the toner cartridge installed.
2. Replace the printer cable. If the problems not solved
even after the cable replaced, check the amount of
the remaining tone.
(refer to Toner Cartridge Service 4-5)
3. Printing is nor working in the Windows.
3. Check if the connection between PC and printer port
is proper. If you use windows, check if the printer driver in the controller is set up. If the printer driver is
properly set up, check in which program the printing
is not working. The best way to find out is to open the
memo pad to check the function of printing. If it is not
working in a certain program, adjust the setup the
program requires. Sometimes, the printout is normal
within the Windows basic programs, but it's not working in a particular program. In such case, install the
new driver again. If not working in the Windows basic
program, Check the setup of the port of CMOS is on
ECP. And check the address of IRQ 7 and 378
4. Check if the printer cable is directly connected to peripheral devices
4-26
4. If the scanner needs to be connected to the printer,
first the remove the scanner from the PC to see if the
printer is properly working alone.
Samsung Electronics
Troubleshooting
4-6-2 The printer is not working (2)
• Description
After receiving the printing order, no response at all or the low speed of printing
occurs due to wrong setup of the environment rather than malfunction of the printer itself.
Check and Cause
Solution
1. Secure more space of the hard disk.
1. Not working with the message 'insufficient printer
memory' means hard disk space problem rather than
the RAM problem. In this case, provide more space
for the hard disk. Secure more space using the disk
utilities program.
2. Printing error occurs even if there is enough space in
the hard disk.
2. The connection of the cable and printer port is not
proper. Check if the connection is properly done and
if the parallel port in CMOS is rightly set up.
3. Check the parallel-port-related items in the CMOS
Setup.
3. As a printer port, Select ECP or SPP among
SPP(Normal), ECP, and EPP modes(increase printing speed) SPP normal mode support 8-bit data
transfer, while ECP Mode transfer the 12-bit data.
4. Reboot the system to print.
4. If the regular font is not printing, the cable or the
printer driver may be defective.
Turn the PC and printer off, and reboot the system
to print again. If not solved, double-click the printer in
my computer If the regular fonts are not printed this
time again. the cable must be defective so replace
the cable with new one.
Samsung Electronics
4-27
Troubleshooting
4-6-3 Abnormal Printing
• Description
The printing is not working properly even when the cable has no problem.
(even after the cable is replaced)
If the printer won't work at all or the strange fonts are repeated, the printer driver may be defective or wrong setup in the CMOS Setup.
Check and Cause
Solution
1. Set up the parallel port in the CMOS SETUP.
1. Select SPP(Normal) or ECP LPT Port the among
ECP, EPP or SPP in the CMOS Setup.
2. Printer Driver Error.
2. Check the printer in My Computer.(to see if the
printer driver is compatible to the present driver or
delete the old driver, if defective and reinstall the new
driver)
3. Error message from insufficient memory.
(The printing job sometimes stops or due to insufficient
virtual memory, but it actually comes from the insufficient space of the hard disk.)
3. Delete the unnecessary files to secure enough
space of the hard disk and start printing job again.
4-28
Samsung Electronics
Troubleshooting
4-6-4 SPOOL Error
• Description
To spool which stands for "simultaneous peripheral operations online" a computer document or
task list (or "job") is to read it in and store it, usually on a hard disk or larger storage medium so
that it can be printed or otherwise processed at a more convenient time (for example, when a
printer is finished printing its current document).
Check and Cause
Solution
1. Insufficient space of the hard disk in the directory
assigned for the basic spool.
1. Delete the unnecessary files to provide more space
to start printing job.
2. If the previous printing error not solved.
2. If there are some files with the extension name of
****.jnl, Delete them and Reboot the Windows to
restart printing job.
3. When expected to collide with other program.
3. Shut down all other programs except the current
one, if possible.
4. When an application program or the printer driver is
damaged.
4. Delete the printer driver completely and reinstall it.
5. When some files related to OS are damaged or virus
infected.
5 After rebooting the computer, check for viruses,
restore the damaged files and reinstall the program
to do the printing job.
6. Memory is less than suggested one.
6. Add up enough memory to the PC.
How to delete the data in the spool manager.
In the spool manager, the installed drivers and the list of the documents waiting to be printed are shown.
Select the document to be deleted and check the delete menu.
If you intend to delete the current document being printed, the data being transferred to the printer will be put
out and then the document is removed. Before choosing the document, the menu is still inactive.
Or put the document out of the list and repeat the routine as in the above or finish the spool manager.
Samsung Electronics
4-29
Exploded Views and Parts List
5. Exploded Views and Parts List
• Deal drawings and service parts are declared for the items with higher rate
of inferiority and replaceable in the level of service description only.
• If inferiority occurs, you can replace the parts by the unit declared in deal
drawings and service items.
Way to observe Part Code & Description
Part code and Description is quoted and controlled by determined standard. Refer to this determined
standard, it will help with ordering Part.
• There ar woo kinds of Part code inscription type.
ex ) 2007-007961
R-CHIP
ex ) JB96-01268A
ELA UNIT-COVER TOP
Type 1 : Controlled by Company : It can be commonly used for all kinds of product SEC produce.
Mostly, electronics Parts.
Type 2 : Controlled by Division : It is used or one produce. Mostly, Mostly, mechanical Parts.
• A/S privately used part : It is only used for A/S .
• Ass’y part : Assembled by more than 2 Parts. If necessary part is not A/S Part, Ass’y part including
necessary par can be used. It is shown in the diagram and drawing of SVC manual.
• Ass’y part and A/S privately used Part is distinguished by part Code and Description.
The are inscription type 2. It is recognized by Part character and front side of description.
Samsung Electronics
DIVISION
A/S Private
PART CODE
**81-******
(JB81-00039A)
DESCRIPTION
AS-*****
(AS-USE)
ASS’Y Part
**75-******
(JB75-00068A)
MEC-*****
(MEC-CHUTE)
ASS’Y Part
**92-******
(JB92-01131A)
PBA ******
(PBA MAIN-CONTROLLER)
ASS’Y Part
**97-******
(JB97-01089A)
MEA ******
(MEA UNIT-PULLEY IDLE)
5-1
Exploded Views and Parts List
5-1 Exploded Views and Parts List
• Service Parts List
NO.
O : Service available X : Service not available
DESCRIPTION
SEC CODE
ELA HOU-HOUSING HAWK16
refer to the
table
1
O
1-1
PMO-COVER OPEN
JC72-00628A
1
O
1-2
PMO-COVER MAIN
refer to the
table
1
O
1-3
PMO-STOPPER HINGE OPEN
JC72-00482A
2
O
1-4
PMO-LENS LED
JC72-00365A
1
O
1-5
PMO-KEY BUTTON
JC72-00499A
1
O
1-6
PBA SUB-PANEL_SEC
JC92-01208D
1
O
1-7
PMO-COVER REAR
JC72-00355A
1
O
1-8
PMO-STACKER REAR
JC72-00356A
1
O
1-9
PMO-COVER CONTROLLER
JC72-00358A
1
O
1-10
MEA UNIT-MP TRAY
JC97-01325A
1
O
1-10-1 PMO-COVER-MP
JC72-00349A
1
O
1-10-2 PMO-TRAY LINK MP
JC72-00350A
2
O
1-11
JC97-01315C
1
O
JC61-40001A
1
O
1
MEA UNIT-BRKT BOTTOM(L)
1-11-1 FOOT-RUBBER
1-12
MEA UNIT-BRKT BOTTOM(R)
1-12-1 FOOT-RUBBER
Q’TY SA
JC97-01316A
1
O
JC61-40001A
1
O
REMARK
2
UNIT-LSU(M)
JC59-00013A
1
O
3
ELA UNIT-MOTOR 16
JC96-02057A
1
O
3-1
MOTOR-STEP 7.5_DEG
JC31-00002A
1
O
3-2
MOTOR-STEP
JC31-00009A
1
O
4
ELA UNIT-DEVE
*
1
X
5
ELA HOU-MPF
JC96-01650A
1
O
5-1
PHOTO-INTERRUPTER
0604-001095
1
O
5-2
SOLENOID-HAWK
JC33-00003A
1
O
5-3
RPR-RUBBER P/UP MP
JC73-10907A
1
O
6
MEA UNIT-FEEDER CST 500
JC97-01466C
1
O 550SHEETS
7
CBF HARNESS-MOTOR
JC39-00157A
1
O
8
MEA UNIT-FEEDER
JC97-01324B
1
O
RMO-RUBBER PICK_UP
JC73-40907A
1
O
9
PMO-CAP SENSOR
JC72-00320A
1
O
10
ELA HOU-ENGINE
JC96-02113A
1
O
110V
ELA HOU-ENGINE
JC96-02114A
1
O
220V
10-1
SHIELD-PCU
JC70-00080A
1
O
10-2
PCT-INSULATOR PCU
JC72-00334A
1
O
10-3
PBA MAIN-ENGINE
JC92-01302A
1
O
8-1
5-2
110V/220V
NO.
DESCRIPTION
SEC CODE
Q’TY SA
10-4
SMPS-HAWK16 SMPS
JC44-00021A
1
O
110V
PWB SMPS V2 (220V)
JC44-00022A
1
O
220V
11
FAN-DC
JC31-00012A
1
O
12
PMO-CAP WIRE
JC72-00656A
1
O
13
IPR-CLAMP EMI
JC70-00009A
1
O
14
ELA UNIT-FRAME BASE HAWK16 JC96-01641J
1
O
110V
ELA UNIT-FRAME BASE HAWK16 JC96-01641K
1
O
220V
14-1
ELA UNIT-HOLDER TR L
JC96-01730A
1
O
14-2
MEC-ROLLER TRANSFER
JC75-00124A
1
O
14-3
ELA UNIT-HOLDER TR R
JC96-01729A
1
O
14-4
GEAR-TR29
JC66-00039A
1
O
14-5
ELA UNIT-GUIDE DEVE L
JC96-01643A
1
O
14-6
ELA UNIT-GUIDE DEVE R
JC96-01642A
1
O
14-7
PBA SUB-EXIT SENSOR
JC92-01234B
1
O
14-8
ELA HOU-VARISTOR
JC96-01772A
1
O
14-9
PBA SUB-FUSER SW
JC92-01261A
1
O
14-10 PBA SUB-SWITCH
JC92-01235A
1
O
14-11 ELA UNIT-EMPTY_ACT HAWK
JC96-01720A
1
O
14-12 ELA UNIT-GUIDE FEED XRX 16 JC96-01653D
1
O
14-13 ELA UNIT-PTL XRX 16
JC96-02126A
1
O
14-14 ELA UNIT-GUIDE TRANSFER
JC96-01645A
1
O
REMARK
15
PBA MAIN-CONTROLLER
JC92-01353A
1
O
16
ELA UNIT-FUSER
JC81-00394A
1
O
110V
ELA UNIT-FUSER
JC81-00393A
1
O
220V
16-1
MEC-ROLLER PRESSURE
JC75-00114A
1
O
16-2
LAMP-HALOGEN
4713-001155
1
O
110V
LAMP-HALOGEN
4713-001156
1
O
220V
THERMOSTAT
4712-000001
1
O
16-3
17
CBF HARNESS-LSU
JC39-00135A
1
O
18
SMPS-HVPS
JC44-00027A
1
O
19
MEA RACK-HOU EXIT
MEA RACK-HOU EXIT
JC97-01338J
JC97-01338K
1
1
O Only 1650/XIL
O
19-1 PMO-HOLDER LEVER
JC72-00631A
1
O
19-2 PHOTO INTERRUPTER
0604-001095
1
O
19-3 PMO-LEVER STACKING
JC72-41188F
1
O
20
PMO-DUCT FAN2
JC72-00627A
1
O
21
PBA MAIN-MOTOR JOINT
JC92-01310A
1
O
22
MEA RACK-CAST SCF-110V
1
X
*
Samsung Electronics
Exploded Views and Parts List
1
1
ELA HOU-HOUSING
HAWK16
ML-1650/XAA
JC96-01590V
ML-1651N/XAA
JC96-02235A
ML-1650/XEF
JC96-01590W
ML-1651N/XEF
JC96-01590Z
ML-1651N/XEC
JC96-01590X
ML-1650/XEG
JC96-01590V
ML-1651N/XG
JC96-02235A
ML-1650/XET
JC96-01590V
ML-1651N/XET
JC96-02235A
ML-1650/XEU
JC96-01590V
ML-1651N/XEU
JC96-02235A
ML-1650/XIL
JC96-01590Y
ML-1651N/XIL
JC96-02275B
ML-1651N/XIP
JC96-02235A
PMO-COVER MAIN
1-7
1-1
JC72-00330U
JC72-0030W
JC72-00330V
JC72-00330X
JC72-00330Y
JC72-00330U
JC72-00330W
JC72-00330U
JC72-00330W
JC72-00330U
JC72-00330W
JC63-00075A
JC72-00330Z
JC72-00330W
1-8
1-2
4
17
20
2
1-3
16
1-4
16-4
1-9
1-5
1-6
16-3
11
16-5
1-3
19
13
14
3-2
19-3
19-2
1-10-2
16-1
19-1
19-3
19-1
12
1-12
1-11
1-10
16-6
16-2
1-10-1
1-12-1
1-11-1
1-10-2
3-1
14
3
5
14-1
7
5-2
5-3
15
14-2
21
5-1
14-5
14-3
14-4
8-1
6
8
14-7
18
14-6
14-8
14-9
10-3
14-10
10-4
14-12
10-2
14-13
10
10-1
14-11
14-14
22
Samsung Electronics
5-3
Exploded Views and Parts List
5-2 All Exploded Views and Parts List
5-2-1 Cover Exploded View
NO.
0
1
Description
Q’ty
ELA HOU-COVER MAIN
1
PMO-COVER OPEN
PMO-COVER MAIN
STOPPER HINGE OPEN
PMO-LENS LED
PMO-KEY BUTTON
PBA PANEL
PMO-COVER REAR
PMO-STACKER REAR
IPR-SPRING LOCKER REAR
PMO-CAP REAR
PMO-SUPPORT MP TRAY
PMO-LEVER_EMPTY, MP
PMO-STOPPER_EXIT,P
2
PMO COVER CONTROLLER
3
MEA UNIT-MP TRAY
3-1
PMO-COVER-MP
3-2
MPR-NAME PLATE XRX
3-3
PMO-CHUTE
3-3-1 PMO-DUMMY CHUTE
3-4
PMO-TRAY HOLDER MP
3-5
IPR-GUIDE LATCH
3-6
PMO-SIDE GUIDE MP
3-7
PMO-TRAY LINK MP
4
MEA UNIT-BRKT BOTTOM(L) XRX
4-1
FOOT-RUBBER
4-2
PMO-BRKT BASE L
4-3
PAPER SIZE SENSOR ASS’Y
5
MEA UNIT-BRKT BOTTOM(R) XRX
5-1
FOOT-RUBBER
5-2
IPR-PLATE CST GUIDE
5-3
PMO-BRKT BASE R
5-4
SCREW-TAPTITE
5-5
IPR-GROUND SCF BASE
6
IPR-BAR CLOSS BOTTOM
S1
SCREW-TAPTITE
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
7
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1
0
1-7
1
1-1
1-13
1-8
1-9
1-2
1-10
1-3
1-11
1-4
1-12
1-5
1-6
2
1-3
4
3-3-1
3-7
3-3
5
4-3
4-2
5-4
5-5
3-4
5-2
3-6
3-1
4-1
3-5
6
3-2
5-1
5-3
3-7
3
6
5-4
Samsung Electronics
Exploded Views and Parts List
5-2-2 Frame Exploded View
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
15-1
15-2
15-3
16
16-1
16-2
16-3
16-4
17
18
18-1
18-2
19
19-1
19-2
20
21
22
22-1
22-2
22-3
23
24
24-1
24-2
25
25-1
25-2
26
27
28
28-1
28-2
28-3
29
29-1
29-2
29-3
29-4
30
30-1
30-2
30-3
31
31-1
31-2
31-3
32
32-1
32-2
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Description
ELA UNIT-FRAME BASE
PMO-GUIDE RIB
CBF HARNESS-INLET ASS’Y
PMO-HOLDER WIRE
KEY DEVE
CBF HARNESS-ENGINE_CONTROL
CBF-HARNESS_FUSER
PBA-EXIT SENSOR
CBF-HARNESS-THERMISTOR JOINT
CBF-HARNESS-MP_CLUTCH ENG
PBA SUB-FUSER SW
PBA SUB-TONER SENSOR
PMO-FRAME COVER
IPR-TERMINAL FU
ELA UNIT-HOLDER TR L
PMO-BUSHING TR
SPRING TR L
PMO-TRANSFER HOLDER
ELA UNIT-HOLDER TR R
PMO-BUSHING TR
SPRING TR R
PMO-TRANSFER HOLDER
IPR-PLATE TR
GEAR-TR29
ELA UNIT-GUIDE DEVE L
PMO-GUIDE DEVE L
SPRING GUIDE DEVE
ELA UNIT-GUIDE DEVE R
PMO-GUIDE DEVE R
SPRING GUIDE DEVE
ELA HOU-VARISTOR
IPR-TERMINAL TR, HAWK
ELA UNIT-SENSOR DEVE
PBA -MICROSWITCH
PMO-HOLDER ACTUATOR
PMO-ACTUATOR DEVE
GROUND FU
ELA UNIT-TERMINAL TR L
ICT-SHAFT HV LARGE
SPRING-HV LARGE
ELA UNIT-TERMINAL TR S
ICT-SHAFT HV LARGE
SPRING-HV SMALL
GROUND-HVPS
IPR-REMOVE KEY
ELA UNIT-ACTUATOR FEED
PMO-ACTUATOR FEED
PMO-HOLDER ACTUATOR
SPRING-FEED HAWK 14
ELA UNIT-GUIDE TRANSFER
PMO-HADER SAW PLATE
IPR-PLATE SAW
IPR-GUIDE TRANSFER
PMO-GUIDE RIB TR
ELA UNIT-GUIDE FEED
PMO-GUIDE OPTIC
GUIDE FEED
PMO-HOLDER G/PAPER
ELA UNIT-PTL
GUIDE PLATE FEED
PMO-HOLDER PTL
PBA SUB-PTL
ELA UNIT-EMPTY ACT
PMO-ACTUATOR EMPTY HAWK
SPRING EMPTY
HINGE GUIDE FEED
GND ICU
PMO-CAP SENSOR
GND MP
GEAR-P/UP DRIVE
GROUND MOTOR
IPR-GUIDE DUST
PBA MAIN-CON_JOINT
IPR-OPC-HAWK
CAP CONNECTOR L
CAP CONNECTOR U
MEC-ROLLER TRANSFER
GEAR IDLE Z27
RING-CS
WASHER-PLAIN
IPR-WASHER SPRING SU
SPRING HINGE FEED
GEAR-EXIT M ID
IPR-GUIDE, DUST
PMO-BASE, FRAME
PMO-GUIDE-SKEW(12)
Samsung Electronics
Q’ty
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
3
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
0
15
44
15-1
15-2
15-3
16
16-1
16-2
16-3
16-4
17
21
13
12
18-2
46
18-1
18
7
45
47
14
46
48
50
19
19-1
38
40
19-2
34
11
51
20
22
8
22-1
10
5
42
37
22-2
43
36
22-3
22-4
9
30
23
30-1
31
30-2
35
24-2
24
25-2 24-1
53
25
25-1
31-3
49
33
41
28-3
28-2
27
27
32-2
28-1
32
32-1
31-2
31-1
4
28
29-3
29-1
29
29-2
29-4
5-5
Exploded Views and Parts List
5-2-3 Exit Exploded View
NO.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Description
MEA RACK-HOU EXIT
PMO-FRAME REAR
GEAR-EXIT/U, ID
RING-CS
GEAR-IDLE 25
SPRING-F/DOWN
PMO-HOLDER EXIT_F/DOWN
PMO-ROLLER-EXIT, MAIN
PMO-ROLLER-EXIT, FR
MEC-BEARING, EXIT RING-C
MEA UNIT-ROLL EXIT
GEAR-EXIT
RMP-RUBBER EXIT_F/UP
ACTUATOR OUT-FULL
MEC-BEARING, EXIT RING-C
GUIDE EXIT
SCREW TAPTITE
PHOTO SENSOR OUT BIN
PMO-HOLDER LEVER
PMO-LEVER STACKING
Q’ty
1
1
1
2
1
4
4
4
4
2
1
1
4
1
2
1
4
1
2
2
0
17
16
16
15
19
18
11
13
9
14
10
4
3
7
8
6
2
5
12
1
5-6
Samsung Electronics
Exploded Views and Parts List
5-2-4 Rack-MPF Exploded View
NO.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Description
ELA HOU-MPF
PHOTO-INTERRUPTER
SCREW-TAPTITE
WASHER-PLAIN
SOLENOID-HAWK
CBF-HARNESS-MP_EMPTY
SPRING KNOCK UP
SPRING-PICK UP, MP
BRACKET_MP
PMO-PLT KNOCK_UP, MP
ICT-SHAFT_P/U, MP
PMO-GEAR P/U MP
PMO-CAM PICK UP MP
PMO-FRAME_MP
PMO-HOLDER_P/U,MP
PMO-HOUSING_P/U, MP
PMO-BEARING-PICK UP
RPR-RUBBER P/UP, MP
PMO-IDLE PICK UP, MP
RPR-PAD KNOCKUP, MP
RCR-FRICTION PAD 1 MP
RCR-FRICTION PAD 2 MP
PMO-RING KNOCK UP MP
SCREW TAPTITE
PMO-ADJUST END MP
RING-E
RING-CS
Q’ty
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
2
1
1
1
0
4
2
25
8
10
12
20
21
14
11
18
16
1
17
6
15
16
7
18
3
25
24
13
26
22
19
9
Samsung Electronics
5-7
Exploded Views and Parts List
5-2-5 Fuser Exploded View
2
4
0
37
7
10
36
12
3
1
1
12
NO.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Description
ELA UNIT FUSER (110V)
ELA UNIT FUSER (220V)
SCREW TAPTITE M3 x 8, BH+
SCREW TAPTITE M3 x 10, FH+
SCREW MACHINE M3 x 6
THERMISTOR-NTC
ELECTRODE FU R
ELECTRODE FU M
ELECTRODE FU L
THERMOSTAT
BRKT GEAR FUSER
GEAR-IDLE 25
GEAR-IDLE 15
RING-CS
COVER FUSER
ROLLER EXIT_F/UP
EXIT_F/UP (SPRING)
SPRING-CLAW
GUIDE-CLAW
LAMP-HALOGEN(110V)
LAMP-HALOGEN(220V)
ROLLER-HEAT
ROLLER PRESSURE
FRAME FUSER
GUIDE INPUT
GEAR FUSER, 32
BUSHING HR-L
BUSHING HR-R
SPRING-BEARING PR
BUSHING PR
PMO GUIDE REAR
SHAFT EXIT_F/UP
BUSHING_TX
GEAR-EXIT
RUBBER EXIT
RUBBER EXIT F/UP
ACTUATOR EXIT
SPRING-ACTUATOR
HOLDER BRUSH
BRUSH ANTISTATIC
HOLDER SHAFT
Q’ty
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
3
3
4
4
1
1
1
1
1
1
1
1
1
2
2
1
1
3
1
3
1
1
1
1
1
1
6
11
9
8
5
13
1
14
15
16
17
32
31
29
30
35
34
33
20
19
28
27
26
23
24
18
21
38
25
22
5-8
Samsung Electronics
Exploded Views and Parts List
5-2-6 Drive Exploded View
NO.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
Description
ELA UNIT-MOTOR
MOTOR-STEP 7.5_DEG
MOTOR-STEP 7.5_DEG
IPR-BRKT GEAR
IPR-BRKT MOTOR
GEAR-FUSER DRV
GEAR-RDCN 123-87
GEAR-OPC DRV 135
GEAR-OPC DRIVE2
WASHER-PLAIN
GEAR-FEED DRV
SCREW-MACHINE
MPR-POLYWASHER8
WASER-PLAIN
Q’ty
1
1
1
1
1
1
1
1
1
1
1
8
1
1
0
3
5
2
4
13
6
11
1
10
9
7
8
Samsung Electronics
5-9
Exploded Views and Parts List
5-2-7 Pick-Up Exploded View
NO.
Description
Q’ty
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
MEA UNIT-FEEDER
SCREW-TAPTITE
WASHER-PLAIN
SPRING-FEED(1)
SPRING-FEED(2)
BEARING-PICK UP
GEAR-P/UP DRIVE
GEAR-FEED
GEAR-PICK UP(12)
IPR-SHAFT FEED
IPR-SHAFT FEED IDLER
IPR-SHAFT PICK UP
GROUND_FEED
IPR-GUIDE_FEED, 16
PMO-HOUSING P/UP
PMO-ROLLER FEED L
PMO-ROLLER FEED S
PMO-SUB HOLDER FEED
PMO-FRAME_FEED
PMO-HOLDER FEED(1)
PMO-HOLDER FEED(2)
PMO-IDLE PICK_UP
PMO-ROLL_FEED, DRV 12
RMO-RUBBER PICK_UP
RMO-LEVER PICK_UP
SPRING PICK UP(12)
RING-CS
1
1
4
1
1
4
1
1
1
1
3
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
8
0
2
5
11
7
24
2
5
9
25
12
26
21
5
2
6
14
23
18
13
5
2
22
4
20
3
15
17
10
16
10
19
1
15
5-10
10
Samsung Electronics
Exploded Views and Parts List
5-2-8 Cassette Exploded View
NO.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Description
MEA UNIT FEEDER CST (500)
PMO-COVER GUIDE EXT
PMO-FRAME CASSETTE
PMO-GUIDE EXT CST
PMO-GUIDE PAPER
PMO-GUIDE SIDE CST
PMO-INDICATOR EMPTY
PMO-SIDE GUIDE EXT
PMO-SUB GUIDE CAST
PMO-HOLDER_INDICATOR
PMO-LOCKER PLATE
IPR-FINGER
IPR-GUIDE EXT LOCK
IPR-GUIDE PAPER SCF
IPR-GUIDE PLT PAPER
IPR-PLATE KNOCK UP
IPR-PLATE SPR LOCK
IPR-SPR PLT G/SIDE
SPRING PLATE K/UP 1
SPRING PLATE K/UP 2
SPRING LOCKER,PLATE
RPR-PAD CST
PMO GUIDE PAPER SIZE
SCREW TAPTITE M3 x 10 NI
LABEL(R)-CASSETTE
GUIDE PAPER DUMMY
Q’ty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
7
1
1
0
15
21
11
12
3
18
17
16
19
5
22
4
10
7
20
24
13
14
25
1
2
8
6
9
Samsung Electronics
5-11
6. Block Diagram
6-1 Video ControllerBlock Diagram
DAT A(0:31)
32
ROM
ADD R(2:22)
100PIN DIM M
ADD R( 0:31)
21
DATA(0:31)
A 20
29LV 160
16Mbit Flash Memory
29LV 160
32
Regulator
2.7V
16Mbit Flash Memory
RD_FL A SH*
Mask Font ROM
K3P5V 1000D-GC, High
22
W R_FL A SH1,2,3
Mask Font ROM
K3P5V 1000D-GC,L ow
32
TS*, TT1, nTSB T,TSIZ(0:2)
CPU
POWER PC
nTA, RST*, I NT*, nTS, nBG
4
PPC603ei
166M Hz
SYSCL K
74F32
RCS(0:3)
3
4
2
74F04
FS781
nW R
F_W R_E
nFSYNC
SPGPi
VCL K *
SDRA M
32
DRA MD(0:3 1)
64M bi t SDRAM
K4S641632C
64M bi t SD RAM
K4S641632C
A DDR(2:18)
Memory Address Bus
DRA MA (0:1 1)
DATA (16:31)
11
nW AI T
nW R
SDRAM _CAS ,SDRAM_RAS,
BA0*,BA1* ,SDRAM_W E* ,
SDRAM _CS( 0:1) ,SDQM (0:3) ,
SD_CLK (1:2) ,CL KE
3
14
EIRQ(0:3)*
Supply Voltage
Supervi sor
74A CT245
Transceiver
93C66
4
4Mbit
Serial
EEPROM
6
nI OCS(0:5)*
C7733
nRD
I NT*
nW A IT
nRD
nW R
TT1
B RDIN*
I OCS1
I OCS2
EI RQ2
60Pin Network Connector
100PIN DIMM
Connector
V ideo-Clock
61.23307M Hz
Memory Data Bus
Centronics
System clock
11.1M Hz(OSC)
Frequency
Scaling EMI
Attenuator
OPTION
Network
Card
RESET*
To
HVPS
&
L REA DY *, LSYNC*
LSU
THV_PWM * ,MHV _PWM*,
DEV_PWM,THV EN*,
L DON* ,PMOTOR*,
LSUCL K ,nVI DEO*
ACK *, BUSY,
SELECT, ERROR,
FAULT*
PD(0:7)
DATA (0:7)
SELI N*
STROBE*
A UTOFD*
INI *
3
I OCS0
8
38
Engi ne I/F Connector
PANEL 8Pi n
5
74HCT273
D Fli p-Flop
Computer
Engine Controller B'd
OP Panel
6-1
Block Diagram
6-2 Engine Block Diagram
A0 - A15
PROGRAM
MEMORY
(27C512)
HVPS control
ADC
• THV READ
• THV / MHV / DEV PWM
PWM
D0 - D7
STEP MOTR
DRIVER
(TEA3718 for Main Motor
& 2916 for Sub-Motor)
SENSOR
Feed_Sensor
Cover_Open
SCF_RDY
P_Empty
P_Exit
MP_Empty
Output_Full
Fuser_SW
-------------------Size1
Size2
Size3
D_T_Sensor
DET_CRU
A0
74HC245
74HC245
A8
CPU
(KS88C4616)
SOLENOID DRIVE
• MAIN CLUTCH
• MP CLUTCH
11.59158MHz
2nd cassette
Feeder
(option)
ADC
Thermister value
FUSER CONTROL
PTL
FAN
VIDEO
CONTROLLER
Interface
6-2
CPU Clock (X-tal)
11.59158MHz
7. Connection Diagram
PTL Ct r l
5V
PT L
Feed Sensor is on B’d
CN 3
Micro Switch on Board
In-24V
Out-24VS
Therm istor
H VPS
Therm 1
Therm 2
CN 2
1- 24VS
2 - GN D _2 4
3- 5VS
4 - GN D 5
5 - T H V _P WM
6 - T H V REA D
7 - T H V _E N *
8 - M H V _PW M
9 - D E V _PW M
1 0- PT L
1 1- GN D 5
1 2- GN D 5
Jo i n t typ e
1 -The r m 1
2 -The r m 2
1 - 5V
2 - Ex i t_s ig nal
3 - GN D _5
Exi t
Senso r
RAM_D IMM
(Opt io n) for RAM _Expand
100pin slot
ROM _DIMM
(Op ti on) f or Demo _SIMM
100pin slot
Ou tpu t Fu l l
se n so r
1- 5V
2 - S i g n al
3- GN D 5
C o n n e ct i o n
T erm inal
1- 5V
2 - T _s e n
3- GN D 5
1- 5V
2 - s i g n al
3- GN D 5
T _se n
so r
Joi nt
B’d
i n t h e CRU
L SU
Pan el B’d
HOST
( PC )
CN 2 4
CN 2 2
CN 20
CN 29
CN 28
1 - L SU _5V
2 - 5V
1 - L SU _C L K
2 - L R EA D Y*
3 - P _M OT OR*
4 - GN D _2 4
5- 24VS
6 - N .C
7 - L SU _V D O*
8 - L D _ON *
9 - GN D 5
1 0- L SU _5V
1 1- H SYN C*
CN 19
Controller
B’d
CN 23
CN 21
C N 26
1- V CC
2 - GN D 5
3- LE D1
4- LE D2
5- LE D3
6- LE D4
7 - K E Y1
8 - K E Y2
9- LE D5
1 0- K EY 3
CN 18
Par al l el Por t
3 6 Pi n
CN 30
36Pin
P 1 2 8 4 Co n .
CN 31
4Pin
U S B Jac k
U SB P or t
4 Pi n
CN 2 7
CN7
1- + 5V
2 - SC F _ST S
3 - SC F _CM D
4 - SC F _CL K
5 - SC F _RD Y
6 - + 2 4V S
7 - GN D 5
8 - GN D 24
CN 8
1 - M ot or 1 _PA
2 - M ot or 1 _PA *
3 - M ot or 1 _PB*
4 - M ot or 1 _PB
CN 1
Engine B’d
CN 25
1 - GN D
2 - Ou tpu t_F ul l *
3 - T _SN E SOR
4- V CC
M i cr o - S w i t c h
( Fo r L SU 5 V S C u t)
T oner
se n s o r B ’d
CN1
1 - GN D _5
2 - GN D _5
3- 5V
4- 5V
5 - GN D _2 4
6 - GN D _2 4
7- 24VS
8- 24VS
9- 24V
1 0- 2 4V
1 - R EA D Y*
2 - n EB SY
3 - n EM SG
4 - CCL K
5 - n CM SG
6 - n F SYN C
7 - n PRIN T
8 - L SY N C *
9 - T H ERM 1
1 0- T H E RM 2
1 1- C OV ER_OPEN
1 2- P_EX IT *
1 3- L D ON *
1 4- PM OT OR *
1 5- L RE A DY *
1 6- L SU C L K
1 7- OU T PU T _F U L L *
1 8- D ET _C RU
1 9- 3 .3 V
2 0- 3 .3 V
2 1- 3 .3 V
2 2- V ID EO*
2 3- V C C
2 4- V C C
2 5- nV ID E O*
2 6- GN D 5
2 7- GN D 5
2 8- GN D 5
1 - T H V _P WM *
2 - T H V _R EA D
3 - T H V EN *
4 - M H V _PW M
5 - D E V _PW M
6- PT L
7 - T _SEN SOR
8 - R es er v ed
9 - R es er v ed
1 0- GN D 2 4
Main
Solenoid
CN 17
Second Cassette
Feeder(Option)
Main Motor
1 - N .C
2 - F A N _J
3 - N .C
4 - M P_SOL _J
5 - N .C
6 - M T R_EN _A
7 - N .C
8 - M T R_PA
9 - SIZ E 1_J
1 0- M T R _E N _B
1 1- SIZ E2 _J
1 2- M T R _P B
1 3- SIZ E3 _J
1 4- + 24 V S
1 5- D GN D
1 6- A GN D
1 7- M P _E M PT Y_J
1 8,19 - D GN D
2 0- 5 V
Connector
Joint B’d
1 - 24VS
2 - MP_SOL
MP Solenoid
CN6
1 - SIZ E 1
2 - SIZ E 2
3 - SIZ E 3
4 - GN D 5
Size Detector
Sensor
CN4
1 - F A N Con tr o l
2 - N.C .
3 - 24 V S
CN2
1- 5V
2 - R XD
3- T XD
4 - GN D - 5 V
CN 2
SUB_MOTOR
JOINT B’D
CN 4
1 - N .C ,. 2 - N .C., 3- 5 V , 4 - /IOC S3, 5- D 3 1, 6- D 3 0,
7 - D 2 9, 8- GN D5 , 9 - D 28 , 1 0 - D 2 7, 11 - D 26 ,
1 2- GN D 5 ,1 3 - D 2 5, 1 4- D 24 , 1 5 - / EIR Q1, 16 - GN D 5,
1 7- A 5 , 1 8- A 4, 1 9- A 3, 20 - /E IRQ0 ,2 1 - A 2 ,22 - D 23 ,
2 3- D 22 , 2 4 - A1 7 , 2 5- D 2 1, 26 - A1 6 , 2 7- D 2 0, 28 - A 15 ,
2 9- D 19 , 3 0 - A1 4 , 3 1- D 1 8, 32 - A1 3 ,
3 3- D 17 , 3 4 - A1 2 , 3 5- D 1 6, 36 - A1 1 , 3 7- A 6 , 3 8- A 1 0,
3 9- / RESET , 40 - A 9, 41 - /W A IT , 42 - A 8, 43 - /IOC S3,
4 4- A 7 , 4 5- / IOCS3 , 4 6- N .C ., 4 7- N .C ., 48 - GN D 5 ,
4 9- A 1 8, 50 - /RD , 51 - /W E, 52 - GN D 5 , 5 3- N .C ., 5 4- N .C .,
5 5- / EIRQ1 , 5 6- GN D 5 , 5 7- N .C ., 5 8- 5 V , 5 9- 5 V , 6 0 - 5 V
( 60 pi n Co nn ec t or )
CN 2
N et w or k
I /F Car d
( O p ti o n )
1- 24v
2 - N .C
3 - F U SER_2 4V S
1 - GN D 5
2- + 5V
3 - GN D 5
4- + 5V
5 - GN D 5
6 - + 3 .3V
7 - GN D 24
8 - + 3 .3V
9 - GN D 24
1 0- 2 4V
1 1- GN D 2 4
1 2- 2 4V
1 3- GN D 2 4
1 4- 2 4V
1 5- F U SE R_ON
1 6- F U SE R_24
DC FAN
1 - M T R_PA
2 - M T R_EN _A
3 - M T R_PB
4 - M T R_EN _B
5 - + 2 4V S
6 - GN D 24
7- + 5V
8 - GN D 5
DCU
(For System Test)
CN 6
MP Empty
Sensor
CN5
CN 1
CN 6
CN 5
1 - MP_EM PTY*
2 - GND 5
3 - 5V
C N7
CN 1
1 - MT R_PA
2 - MT R_PA *
3 - MT R_PB
4 - MT R_PB *
SUB_MOTOR
Fuser _Sw it ch
SMPS B’d
CN 3
CN 5 0 2
H OT
N e utr a l
CN 5 0 1
H OT
N e utr al
H eat L amp (Fuse r)
Power SW
AC In-Let
110V for USA
220V for EU
7-1
9. Schematic Diagrams
9-1 Main Circuit Diagram(1/10)
ED
A
R
P
EDIT
SIGN
REF NO
1
C
H
E
C
K
SEC
E
N
G
2
D
W
G
3
9-1
Schematic Diagrams
Main Circuit Diagram(2/10)
ED
A
P
R
EDIT
SIGN
REF NO
1
C
H
E
C
K
SEC
E
N
G
2
D
W
G
3
9-2
Schematic Diagrams
Main Circuit Diagram(3/10)
ED
A
P
R
EDIT
SIGN
REF NO
1
C
H
E
C
K
SEC
E
N
G
2
D
W
G
3
9-3
Schematic Diagrams
Main Circuit Diagram(4/10)
ED
A
R
P
EDIT
SIGN
REF NO
1
C
H
E
C
K
SEC
E
N
G
2
D
W
G
3
9-4
Schematic Diagrams
Main Circuit Diagram(5/10)
ED
A
R
P
EDIT
SIGN
REF NO
1
C
H
E
C
K
SEC
E
N
G
2
D
W
G
3
9-5
Schematic Diagrams
Main Circuit Diagram(6/10)
ED
P
A
R
EDIT
SIGN
REF NO
1
C
H
E
C
K
SEC
E
N
G
2
D
W
G
3
9-6
Schematic Diagrams
Main Circuit Diagram(7/10)
ED
A
R
P
EDIT
SIGN
REF NO
1
C
H
E
C
K
SEC
E
N
G
2
D
W
G
3
9-7
Schematic Diagrams
Main Circuit Diagram(8/10)
ED
A
R
P
EDIT
SIGN
REF NO
1
C
H
E
C
K
SEC
E
N
G
2
D
W
G
3
9-8
Schematic Diagrams
Main Circuit Diagram(9/10)
D7
RB420D T147
D5
RB420D T147
D6
RB420D T147
EDIT
SIGN
ED
A
R
P
REF NO
1
C
H
E
C
K
E
N
G
SEC
2
D
W
G
3
9-9
Schematic Diagrams
Main Circuit Diagram(10/10)
EDIT
SIGN
ED
A
R
P
REF NO
1
C
H
E
C
K
E
N
G
SEC
2
D
W
G
3
9-10
Schematic Diagrams
9-2 Engine Circuit Diagram(1/5)
9-11
Schematic Diagrams
Engine Circuit Diagram(2/5)
MTR2_EN_A
DGND
MTR_PA
MTR2_EN_A
DGND
DGND
14
13
18
AGND
15
10
RC1
_ENABLE1
16
E1
OUT1B
17
LOADSPLY
REFERENCE
GROUND
OUT2A
SENSE2
OUT2B
2
4
AGND
E2
PHASE2
_ENABLE2
RC2
5
U5
9
11
1
OUT1A
A2918SWV
6
LOGICSPLY
SENSE1
AGND
3
PHASE1
12
7
8
+24VS
DGND
+5V
DGND
MTR_PB
MTR2_EN_B
9-12
Schematic Diagrams
Engine Circuit Diagram(3/5)
+24VS
CN7-1
+5V
1
2
3
4
5
6
7
8
DGND
+5V
DGND
+5V
R47
5.6K
R75
5.6K
R42
5.6K
100
100
R48
R46
R44
R43
SCF_STS
SCF_CMD
SCF_CLK
SCF_RDY
9-13
Schematic Diagrams
Engine Circuit Diagram(4/5)
CN1-1
1
2
3
4
5
6
7
8
9
10
+5V
AGND
DGND
24V
D9
M4
Q5
KSC1008-Y
AGND
AGND
R39
100
3
1
C21
47uF
50V
C37
10nF
DGND
2
C46
100nF
+24VS
DGND
R52
510
MP_EMPTY*
R53
5.6K
DGND
MP_SOL
A
FUSER_ON
1
K
2
R4
150
DGND
C
E
AGND
3
2
1
R29
1.8K
3
R32
5.6K
R19
100
R20
15K
R34
5.1K
C32
1nF
DGND
C20
10nF
U8
GP1S523
4
DGND
E
C
R33
3.3K
DGND
R21
150
DGND
2
K
A
1
R35
1K
Q4
MMBT2222ALT1
R3
15K
DGND
C2
10nF
R2
3
100
U3
GP1S523
4
DGND
R31
4.7K
3
3
U9-1
1
LM393D
2
2
Q2
MMBT2222ALT1
R30
1K
1
DGND
8
4
C38
1nF
DGND
C26
100nF
3
2
Q7
MMBT2222ALT1
DGND
FEED_SENSOR*
P_EMPTY*
1
BD1
INSTPAR
THERM1
THERM2
FUSER*
FAN
MAIN_SOL
C47
100nF
R54
510
R6
510
R55
5.6K
R7
5.6K
D10
M4
2
3
1
Q6
KSC1008-Y
3
1
Q1
KSC1008-Y
DGND
D1
M4
2
DGND
AGND
AGND
L3
CLUCH
9-14
Schematic Diagrams
Engine Circuit Diagram(5/5)
9-15
Schematic Diagrams
9-3 HVPS Circuit Diagram(1/3)
CN2
1
2
3
4
5
6
7
8
9
10
11
12
1
CN1
5267-10A
2
3
4
5
6
7
8
9
10
24VS
A-GND
5V
D-GND
THV-PWM
THV-READ
THV-EA
MHV-PWM
BIAS-PWM
PTL
D-GND
D-GND
D-GND
D-GND
5V
5V
A-GND
A-GND
24VS
24VS
24V
24V
C6
104
C5
104
24V
24VS
A-GND
5V
D-GND
THV-PWM
THV-READ
THV-EA
MHV-PWM
BIAS-PWM
D-GND
D-GND
5V
A-GND
24VS
Q1
C1008-Y
SW1
SS-5GL111D2
1
2
CN3
53014-0210
24VS
D1
1N4148
CHECKED
5V
APPROVED
DONGYANG INSTRUMENTS
DESIGNED
J.S.YOUN
TITLE
JC92-01175A
1 OF 3
REV
1.53
HAWK-HVPS
REF. NO
DATE 00/03/11
DRW. NO
SIZE A4
9-16
Schematic Diagrams
HVPS Circuit Diagram(2/3)
THV-PWM
CN2-#5
5V
CN1-#3,4
CN2-#7
THV-EA
3
U2-B
7407
4
5V
5
R201
10K
24VS
U2-C
7407
+
C101
35V 47uF
18V
R3
1/2W 560
2
7
U2-A
7407
R316
1KF
D-GND
1
14
THV-READ
CN2-#6
R317
2KF
6
R206
100
R205
1K
8
Q203
A708-Y
R207
2K
-
+
ZD1
5.6V
24VS
U1-C
KA324
4
11
R301
470K
C301
222
18V
10
9
R208
30KF
R209
100KF
C7
104
C4
104
R302
33K
C201
103
C202
331
R303
100KF
VR201
50K
C302
102
D301
1N4148
C303
333
D302
1N4148
R210
845KF
D201
1N4148
D202
1N4148
R304
200KF
R305
6.2KF
VR301
5K
R211
1MF
5
6
R306
26.1KF
7
C203
223
D200
1N4004
1
5
2
4
R214
2.2K
T301
KAB-006
7
6
1
5
2
4
D303
4KV
T201
T1167
R215
430
C204
473
C307
3KV 471
C306
2KV 680
7
6
C206
6KV 471
D204
4KV
C207
6KV 471
TITLE
D205
4KV
THV
R218
MGR1/2W100KF
R217
SBR1/2W 200MG
REF. NO
DATE 00/09/09
JC92-01175A
2 OF 3
REV.
1.53
HAWK-HVPS
R315
SBR1/2W 30MJ
R216
SBR1/2W 30MJ
C205
2KV 101
D304
4KV
C308
3KV 471
DONGYANG INSTRUMENTS
R314
2.2KF
ZD202
7.5V
Q204
D526-Y
R312
1W 56
R313
1W 56
VR302
5K
C305
333
Q303
D526-Y
ZD201
5.6V
R213
2.2K
24VS
D203
1N4148
18V
R311
110KF
Q301
A708-Y
18V
R310
2.2K
Q302
A708-Y
U1-B
KA324
+
-
R212
470K
R309
2.2K
R307
33K
R308
33K
C304
500V 103
SIZE A4
DESIGNED CHECKED APPROVED DRW. NO
J.S.YOUN
9-17
Schematic Diagrams
HVPS Circuit Diagram(3/3)
R422
5.6K
MHV-PWM
CN2-#8
BIAS-PWM
CN2-#9
5V
13
R401
100
18V
R403
110KF
R402
56KF
VR401
50K
C2
104
VR501
50K
R505
110KF
Q501
A708-Y
18V
R504
2K
R412
2K
Q401
A708-Y
OUT
R503
100
R502
2.2K
GND
U3
KA7818
10
12
R411
2.2K
U2-F
7407
IN
U2-E
7407
R501
5.6K
11
5V
24VS
C1
104
R506
100KF
R404
33KF
C501
104
18V
C401
331
R508
86.6KF
C502
222
R507
27KF
C408
104
+
C3
35V 47uF
R405
220KF
R406
2.2KF
R509
12KF
C402
103
12
+
+
-
R407
240K
1
U1-D
KA324
R510
47K
U1-A
KA324
D403
D1NS4
13
C503
104
2
3
D501
1N4148
14
C403
333
R512
430
1
5
2
4
T401
KAB-006
R513
1W 3
24VS
Q502
D526-Y
R410
1W 3
24VS
Q402
D526-Y
R408
47K
R409
430
R511
47K
C504
333
6
7
7
6
D502
4KV
D401
4KV
C505
2KV 680
D402
4KV
C404
3KV 471
T501
KAB-006
C405
2KV 680
1
5
2
4
C406
3KV 471
R413
MGR1/2W6MF
R414
MGR1/2W6MF
ZD401
1W 200V
R514
MGR1/2W15MF
C506
3KV 471
R515
MGR1/2W6MF
R520
MGR1/2W9MF
DONGYANG INSTRUMENTS
R426
MGR1/2W100KF
R416
MGR1/2W15MF
R417
MGR1/2W15MF
R516
MGR1/2W50K
ZD501
1W 150V
R519
MGR1/2W50K
R517
MGR1/2W6MF
REF. NO
DATE 00/12/11
JC92-01175A
MHV
OPC
SUPPLY
DEV
3 OF 3
REV.
1.53
HAWK-HVPS
R518
MGR1/2W9MF
TITLE
SIZE A4
DESIGNED CHECKED APPROVED DRW. NO
J.S.YOUN
9-18
Schematic Diagrams
9-4 Motor Circuit Diagram
9-19
Schematic Diagrams
9-5 Jointr Circuit Diagram
9-20
Schematic Diagrams
9-6 SMPS Circuit Diagram(110V)
CN1
L
N
F.G
CN2
FUSE1
125V 8A
R201
221K
TNR1
471K
TNR2
C201
630V
333
R1
1W 560K
C1
224
L201
300uH
R203
1W 47
FUSIBLE
C202
1W 180
FUSIBLE
BTA12-600
THY201
50V
104
LF1
1706
C3
222MAD
C4
222MAD
U1
IRF840
R8 470
BD3
JUMPER
R6
1W
0.075
R7
100
D2
1N4148
F2
125V 5A
R5
3
5
LF2
UL50055
C9
222J
4
C10
102
C2
224
1
IC1(KA7552)
7
-
+
8
6
BD1
D3SB60
2
R12
180
R11
3.6K-F (75KHz)
R9
C12
104
TH1
10D-9
C6
R2
R23
R3
1W 100K
1W 100K
200V
470uF
Z2
PC1-1
PC123
C11
104
C7
103K
C13
50V
33uF
200V1A
D3
Z1
JUMPER
BD2
JUMPER
C8
1K471
C5
R4
3W
47K
3
1
NP
D1
UF4007
R10
1/4W
22
6
NB
7
T1
R13
1/4W 22
D4
B5A90VI
R14
1/4W 22
C14
1K102
C19
35V
1000uF
C18
1K 102
C23
1K 102
D5
SF10LC20U
R21
1/4W 15
D6
SF10LC6
C15
10V
1000uF
C24
10V
1000uF
I
R15
680
O
C20
50V1uF
L1
10uH
R16
O
U2
378R33
PC1
PC123
U3
KA431
U4
378R05
I
G
222MAD
G
2
1
R202
1/4W
100
U201
MOC3061
R204
1/2W
1.5K
+24VS2
CN3 12
FUSER_ON
CN3 8
NO MARKING RESISTOR 1/8W-J (5%)
C16
10V
1000uF
R17
21.5KF
R18
2.49KF
C17
104
C21
35V
1000uF
C25
10V
1000uF
R20,26
2W 1K*2
C26
104
C22
104K
CN3
1,2
3.3V
1.5A
CN3
3,4,5
3.3V
GND
CN3
24V 3A
CN3
9,10,11
5V
GND
CN3 6,7
5V 1.5A
CN3 3,4,5
24V GND
9-21
Schematic Diagrams
SMPS Circuit Diagram(220V)
CN1
L
N
F.G
CN2
22
FUSE1
250V 5A
R201
221K
471K
TNR2
BTA12-600
THY201
630V
333
C201
TNR1
1W 47
FUSIBLE
104
C202
50V
R1
1W 560K
C1
224
L201
300uH
R203
1W 180
FUSIBLE
1706
LF1
222MAD
C3
C4
222MAD
U1
SSP5N80
R8 150
BD3
JUMPER
R6
1W
0.15
R7
150
D2
1N4148
F2
250V 2A
R5
3
5
LF2
UL50055
C9
222J
4
C10
102
C2
224
1
IC1(KA7552)
7
-
+
8
6
BD1
D3SB60
2
R12
120
R11
3.6K-F (75KHz)
R9
C12
104
TH1
10D-9
C6
400V
150uF
R2
C7
103K
C13
50V
33uF
200V1A
D3
Z1
1M150
BD2
JUMPER
C8
1K471
C11
104
PC2-1
1W 100K
R3
R23
150
1W 100K
Z2
24C
PC1-1
PC123
C5
222MAD
R4
47K
3W
3
1
NP
D1
UF4007
R10
1/4W
22
6
NB
7
T1
R13
1/4W22
C19
35V
1000uF
C23
1K102
C18
1K102
C14
1K102
D4
B5A90VI
R14
1/4W22
D5
SF10LC20U
R21
1/4W22
D6
SF10LC6
C15
10V
1000uF
C24
10V
1000uF
R15
820
I
O
C20
50V1uF
L1
10uH
R16
O
U2
378R33
PC1
PC123
U3
KA431
I
U4
378R05
G
2
1
R202
1/4W
U201
MOC3061
R204
1/2W
1.5K
+24VS2
CN3 12
FUSER_ON
CN3 8
NO MARKING RESISTOR 1/8W-J (5%)
C16
10V
1000uF
R17
21.5KF
R18
2.49KF
C17
104
C21
35V
1000uF
C25
10V
1000uF
R20,26
2W 1K*2
C26
104
C22
104K
CN3
3.3V
1.5A
CN3
3.3V
GND
CN3
24V 3A
CN3
24V
GND
CN3
5V 1.5A
CN3
5V GND
9-22
G