advertisement
Pundit P3-PH4
PC (Desktop Barebone)
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS
OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY
OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
Table of contents
Notices ................................................................................................ vi
Safety information ............................................................................. vii
About this guide ............................................................................... viii
System package contents ................................................................... x
1.1
Welcome! .............................................................................. 1-2
1.2
Front panel ........................................................................... 1-2
1.3
Rear panel ............................................................................. 1-4
1.4
Internal components ............................................................ 1-6
2.1
Preparation ........................................................................... 2-2
2.2
Before you proceed .............................................................. 2-2
2.3
Removing the covers ............................................................ 2-3
2.3.1
Removing the system cover ................................... 2-3
2.3.2
Removing the front panel assembly ....................... 2-4
2.4
Installing a CPU ..................................................................... 2-5
2.4.1
CPU installation ....................................................... 2-5
2.4.2
Installing the CPU fan and heatsink assembly ........ 2-7
2.5
Installing a DIMM ................................................................... 2-8
2.5.1
Memory configurations ........................................... 2-8
2.5.2
Installing a DIMM ................................................... 2-10
2.5.3
Removing a DIMM ................................................. 2-10
2.6
Installing an expansion card ............................................... 2-11
2.6.1
Expansion slots ..................................................... 2-11
2.6.2
Expansion card installation ................................... 2-11
2.7
Installing an optical drive .................................................... 2-14
2.8
Removing the card reader .................................................. 2-16
2.9
Installing hard disk drives (HDDs) ....................................... 2-17
2.9.1
Hard disk drive bays ............................................. 2-17
2.9.2
SATA hard disk drive installation .......................... 2-17
2.9.3
IDE hard disk drive installation .............................. 2-19
2.9.4
Uninstalling a hard disk drive ................................ 2-19
Table of contents
2.10
Replacing the covers .......................................................... 2-20
2.10.1 Replacing the front panel assembly ...................... 2-20
2.10.2 Replacing the system cover ................................. 2-21
2.11
Installing the foot stands ................................................... 2-22
2.12
Selecting the voltage ......................................................... 2-23
3.1
Installing an operating system ............................................. 3-2
3.2
Support CD information ........................................................ 3-2
3.2.1
Running the support CD ......................................... 3-2
3.2.2
Drivers menu .......................................................... 3-3
3.2.3
Utilities menu .......................................................... 3-4
3.2.4
Manual .................................................................... 3-5
3.2.5
ASUS contact information ...................................... 3-6
3.2.6
Other information ................................................... 3-6
4.1
Motherboard overview .......................................................... 4-2
4.2
Jumper ................................................................................. 4-3
4.3
Connectors ........................................................................... 4-4
4.3.1
Rear panel connectors ............................................ 4-4
4.3.2
Internal connectors ................................................. 4-4
5.1
Managing and updating your BIOS ........................................ 5-2
5.1.1
ASUS CrashFree BIOS 2 utility ................................ 5-2
5.1.2
ASUS Update utility ................................................ 5-3
5.2
BIOS setup program ............................................................. 5-6
5.2.1
BIOS menu screen ................................................... 5-7
5.2.2
Menu bar ................................................................. 5-7
5.2.3
Navigation keys ...................................................... 5-6
5.2.4
Menu items ............................................................. 5-8
5.2.5
Sub-menu items ..................................................... 5-8
5.2.6
Configuration fields ................................................ 5-8
5.2.7
Pop-up window ....................................................... 5-8
Table of contents
5.2.8
Scroll bar ................................................................ 5-8
5.2.9
General help ............................................................ 5-8
5.3
Main menu ............................................................................ 5-9
5.3.1
System Time ........................................................... 5-9
5.3.2
System Date ........................................................... 5-9
5.3.3
Primary IDE Master/Slave;
Third and Fourth IDE Master ................................. 5-10
5.3.4
IDE Configuration .................................................. 5-11
5.3.5
System Information .............................................. 5-13
5.4
Advanced menu .................................................................. 5-14
5.4.1
JumperFree Configuration .................................... 5-14
5.4.2
USB Configuration ................................................. 5-16
5.4.3
CPU Configuration ................................................. 5-18
5.4.4
Chipset ................................................................. 5-20
5.4.5
Onboard Devices Configuration ............................ 5-21
5.4.6
PCI PnP ................................................................. 5-23
5.5
Power menu ........................................................................ 5-24
5.5.1
Suspend Mode ...................................................... 5-24
5.5.2
Repost Video on S3 Resume ................................ 5-24
5.5.3
ACPI 2.0 Support .................................................. 5-24
5.5.4
ACPI APIC Support ................................................ 5-25
5.5.5
APM Configuration ................................................ 5-25
5.5.6
Hardware Monitor ................................................. 5-26
5.6
Boot menu .......................................................................... 5-27
5.6.1
Boot Device Priority .............................................. 5-28
5.6.2
Boot Settings Configuration ................................. 5-28
5.6.3
Security ................................................................ 5-29
5.7
Exit menu ........................................................................... 5-32
Appendix: CPU features
A.1
Intel ® EM64T ......................................................................... A-2
A.2
Enhanced Intel SpeedStep ® Technology (EIST) ................... A-2
A.2.1
System requirements ............................................. A-2
A.2.2
Using the EIST ........................................................ A-3
A.3
Intel ® Hyper-Threading Technology ..................................... A-4
Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
the graphics card is required to assure compliance with FCC regulations.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Safety information
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
• Before installing devices into the system, carefully read all the documentation that came with the package.
• Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet. Place the product on a stable surface.
• If you encounter technical problems with the product, contact a qualified service technician or your retailer.
Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturerís instructions.
Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnljchen Typ. Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.
About this guide
This guide provides general information and installation instructions about the ASUS Pundit P3-PH4 barebone system. This guide is intended for experienced users and integrators with hardware knowledge of personal computers.
This guide contains the following parts:
1 .
C h a p t e r 1 : S y s t e m i n t r o d u c t i o n
This chapter gives a general description of the barebone system. The chapter lists the system features including introduction on the front and rear panel, and internal components.
2 .
C h a p t e r 2 : B a s i c i n s t a l l a t i o n
This chapter provides step-by-step instructions on how to install components in the system.
3 .
C h a p t e r 3 : G e t t i n g s t a r t e d
This chapter helps you power up the system and install drivers and utilities from the support CD.
4 .
C h a p t e r 4 : M o t h e r b o a r d i n f o
This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations.
5 .
C h a p t e r 5 : B I O S s e t u p
This chapter tells how to change system settings through the BIOS
Setup menus and describes the BIOS parameters.
6 .
A p p e n d i x : C P U f e a t u r e s
The Appendix describes the CPU features and technologies that the motherboard supports.
trying to complete a task.
when trying to complete a task.
task.
task.
Refer to the following sources for additional information and for product and software updates.
1 .
A S U S W e b s i t e s
The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to the ASUS contact information.
2 .
O p t i o n a l D o c u m e n t a t i o n
Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.
xxxxx
System package contents
Check your Pundit P3-PH4 system package for the following items.
If any of the items is damaged or missing, contact your retailer immediately.
1 .
A S U S P u n d i t P 3 - P H 4 b a r e b o n e s y s t e m w i t h
• ASUS motherboard
• 275 W PFC power supply unit
• 6-in-1 storage card reader
2 .
A c c e s s o r i e s
• CPU fan and heatsink assembly
• Foot stand and screw (1 pair) for vertical placement
• Rubber stand (x 4) for horizontal placement
• Hard disk drive screw (x 8)
• Optical drive screw (x 2)
• Rubber washer (x 8)
3 .
C a b l e s
• AC power cable
• Serial ATA signal cable (x 2)
4 .
S u p p o r t C D
5 .
U s e r g u i d e
6 .
O p t i o n a l c o m p o n e n t
• Optical drive (CD-ROM/CD-RW/DVD-ROM/DVD-RW)
Chapter 1
This chapter gives a general description of the barebone system. The chapter lists the system features including introduction on the front and rear panel, and internal components.
1.1
Welcome!
Thank you for choosing the ASUS Pundit P3-PH4!
The ASUS Pundit P3-PH4 is an all-in-one barebone system with powerful and flexible features.
The system comes in a stylish mini-tower casing, and powered by the ASUS motherboard that supports the Intel ® Pentium ® 4 processor in the 775-land package with 1066 MHz FSB and up to 4 GB system memory.
With audio capabilities, extensive connectivity, and Fast Ethernet LAN,
Pundit P3-PH4 is designed for the sophisticated. The system’s ergonomic design allows vertical or horizontal placement so you can maximize your desktop space.
With these and many more, the Pundit P3-PH4definitely delivers the cutting edge technology for your computing and multimedia needs.
1.2
Front panel
The front panel includes the front panel cover, system and audio control buttons, and LEDs.
h e r e t o
1 1
1 2
1 3
1 4
1 5
1 .
O p t i c a l d r i v e e j e c t b u t t o n . drive tray.
2 .
M e m o r y S t i c k a Memory Stick ® /Memory Stick Pro™ storage card.
3 .
Optical drive/bay cover.
4 .
C o m p a c t F l a s h ® c a r d s l o t * ..... This slot is for a CompactFlash ® storage card.
5 .
H D D L E D . to the hard disk drive.
6 .
P o w e r L E D .
7 .
P o w e r b u t t o n .
8 .
F r o n t p a n e l c o v e r .
I/O ports. Press the indicated area to open the front panel cover.
Refer to the illustration in the previous page.
9 .
S m a r t M e d i a card.
storage or written to a storage card inserted in any of the card reader slots.
Secure Digital™/MultimediaCard storage card.
1 2 . H e a d p h o n e p o r t . mini-plug.
1 3 . M i c r o p h o n e p o r t .
..... This port provides high-speed connectivity for IEEE 1394a-compliant audio/video devices, storage peripherals, and other PC devices.
ports are available for connecting USB 2.0 devices such as a mouse, printer, scanner, camera, PDA, and others.
*Use and format a storage card according to the documentation that comes with it.
1.3
Rear panel
The system rear panel includes the power connector and several I/O ports that allow convenient connection of devices.
3 4 5 6 7 8 9 1 0
1 5 1 6 1 7 1 8 1 9
1 .
C o v e r s c r e w .
2 .
PS/2 mouse port
3 .
P a r a l l e l p o r t ..... This 25-pin port connects a printer, scanner, or other devices.
4 .
A i r v e n t .
5 .
6 - p i n I E E E 1 3 9 4 a p o r t
IEEE 1394a-compliant audio/video devices, storage peripherals, and other consumer electronic devices.
6 .
L A N ( R J - 4 5 ) p o r t . a Local Area Network (LAN) through a network hub.
7 .
C e n t e r / S u b w o o f e r p o r t ( y e l l o w o r a n g e ) . the center/subwoofer speakers.
8 .
L i n e I n p o r t ( l i g h t b l u e ) . other audio sources.
9 .
L i n e O u t p o r t ( l i m e ) . speaker. In 4/6/8-channel configuration, the function of this port becomes Front Speaker Out.
brackets.
according to the voltage supply in your area. See the “Voltage selector” section on page 2-x before adjusting this switch.
1 3 . P S / 2 k e y b o a r d p o r t . This purple 6-pin connector is for a PS/2 keyboard.
1 4 . S e r i a l p o r t . Connects a mouse, modem, or other devices that conforms with serial specification.
1 5 . V G A p o r t . ports are available for connecting USB 2.0 devices such as a mouse, printer, scanner, camera, PDA, and others.
speakers in an 8-channel audio configuration.
speakers in a 4/6/8-channel audio configuration.
6-channel mode, the function of this port becomes Surround Speaker.
The functions of the Line Out, Line In, and Microphone ports change when you select the 6/8-channel configuration. Refer to the table below for audio ports function variation.
Light Blue
Lime
Pink
Gray
Black
Yellow Orange
Line In
Line Out
Mic In
–
–
–
Line In
Front Speaker Out
Mic In
Rear Speaker Out
–
–
Line In
Front Speaker Out
Mic In
Rear Speaker Out
–
Center/Subwoofer
Line In
Front Speaker Out
Mic In
Rear Speaker Out
Side Speaker Out
Center/Subwoofer to add memory and graphics capabilities to the system.
power supply fan.
1.4
Internal components
The illustration below is the internal view of the system when you remove the top cover and the chassis support bracket. The installed components are labeled for your reference. Proceed to Chapter 2 for instructions on installing additional system components.
1 3
1 1
1.
5.25-inch empty optical drive bay
2.
Front panel cover
3.
Optical drive lock
4.
Hard disk drive bays
5.
Hard disk drive lock
6.
Power supply unit
7.
PCI Express x1 slot
8.
PCI slots
9.
PCI Express x16 slot
10. ASUS motherboard
11. Metal bracket lock
12. LGA775 socket
13. DIMM sockets
Chapter 2
This chapter provides step-by-step instructions on how to install components in the system.
2.1
Preparation
Before you proceed, make sure that you have all the components you plan to install in the system.
1.
Central processing unit (CPU)
2.
DDR Dual Inline Memory Module (DIMM)
3.
Expansion card(s)
4.
Hard disk drive
5.
Optical drive
2.2
Before you proceed
Take note of the following precautions before you install components into the system.
• Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.
The system motherboard comes with an onboard standby power LED. This
LED lights up to indicate that the system is ON, in sleep mode or in soft-off mode, and not powered OFF. Unplug the power cable from the power outlet and make sure that the standby power LED is OFF before installing any system component.
2.3
Removing the covers
2.3.1
Removing the system cover
To remove the cover and metal chassis support:
1.
On the rear panel, locate the two thumb screws that secure the cover to the chassis.
2.
Remove the cover screws.
Keep the screws for later use.
3.
Slightly pull the cover toward the rear panel until the cover hooks disengages from the chassis holes.
4.
Lift the system cover, then set aside.
5.
Lift the expansion card lock to a 90º-100º angle.
6.
Lift the chassis support bracket to a 45º angle, then carefully pull to release. Set the chassis support bracket aside.
2.3.2
Removing the front panel assembly
To remove the front panel assembly:
1.
Place the system vertically.
2.
Locate the front panel assembly hooks.
3.
Pull the hooks outward to release the front panel assembly.
4.
Swing the left edge of the front panel assembly outward.
5.
Unhook the hinge-like tabs from the holes on the right side of the chassis to detach.
Do not use too much force when removing the front panel assembly.
2.4
Installing a CPU
The ASUS motherboard comes with a surface mount LGA775 socket designed for the Intel ® Pentium ® 4 processor in the 775-land package.
2.4.1
CPU installation
• Your boxed Intel ® Pentium ® 4 LGA775 processor package should come with installation instructions for the CPU, heatsink, and the retention mechanism. If the instructions in this section do not match the CPU documentation, follow the latter.
• Check your motherboard to make sure that the socket contacts are not bent. Contact your retailer immediately if you see any damage to the socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related.
• The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation or removal.
To install a CPU:
1.
Locate the CPU socket.
2.
Unlock the load lever.
3.
Lift the load lever.
4.
Lift the load plate.
5.
Carefully push the PnP cap from the load plate window to remove.
6.
Install the CPU, noting the position of the gold triangle as shown.
7.
Close the load plate.
8.
Push the load lever until it snaps into the retention tab.
The motherboard supports Intel ® Pentium ® 4 LGA775 processors with the Intel ® Enhanced Memory 64 Technology (EM64T), Enhanced Intel
SpeedStep ® Technology (EIST), and Hyper-Threading Technology. Refer to the Appendix for more information on these CPU features.
2.4.2
Installing the CPU fan and heatsink assembly
The system package includes a pre-installed proprietary CPU fan and heatsink assembly to ensure optimum thermal condition and performance.
models.
To install the CPU fan and heatsink assembly:
1.
Place the heatsink on top of the installed CPU.
2.
Drive four screws into the fan holes to secure the fan to the motherboard.
3.
Connect the CPU fan cable.
Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fai to plug this connector.
2.5
Installing a DIMM
The system motherboard comes with four Double Data Rate 2 (DDR2) Dual
Inline Memory Module (DIMM) sockets.
A DDR2 module has the same physical dimensions as a DDR DIMM but has a
240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket.
The figure illustrates the location of the DDR2 DIMM sockets.
240-pin DDR2 DIMM sockets
2.5.1
Memory configurations
You may install up to 4 GB system memory using 256 MB, 512 MB, and
1 GB DDR DIMMs.
• Installing DDR DIMMS other than the recommended configurations may cause memory sizing error or system boot failure. Use any of the recommended configurations in the table on the next page.
• i d e n t i c a l
DIMM_A and DIMM_B.
• Always install DIMMs with the same CAS latency. For optimum compatibility, we recommend that you obtain memory modules from the same vendor.
• Due to chipset resource allocation, the system may detect less than
4 GB system memory when you installed four 1 GB DDR memory.
• This motherboard does not support memory modules made up of
128 Mb chips or double-sided x16 memory modules.
The following tables list the memory modules that have been tested and qualified for use with this motherboard. Visit the ASUS website
(www.asus.com) for the latest DDR2 DIMM modules for this motherboard.
DDR2 533 Qualified Vendors List
512MB
256MB
512MB
512MB
SAMSUNG
SAMSUNG
SAMSUNG
Infineon
256MB Infineon
1024MB Infineon
512MB
512MB
Infineon
CORSAIR
512MB MICRON
1024MB MICRON
256MB MICRON
512MB MICRON
1024MB Kingston
256MB Kingston
512MB
512MB
512MB
Kingston
Hynix
Hynix
1024MB Hynix
512MB ELPIDA
1024MB ELPIDA
M378T6553BG0-CD5
M378T3253FG0-CD5
M378T6453FG0-CD5
HYS64T64000GU-3.7-A
HYS64T32000HU-3.7-A
HYS64T128020HU-3.7-A
HYS64T64000HU-3.7-A
CM2X512-4200
MT16HTF6464AG-53EB2
MT16HTF12864AY-53EA1
MT8HTF3264AY-53EB3
MT16HTF6464AY-53EB2
D6408TE7BL-37
E5116AB-5C-E
HY5PS56821F-C4
HYMP564U648-C4
HY5PS1282AFP-C3
HYMP512U648-C4
EBE51UD8ABFA-5C
EBE11UD8ABFA-5C-E
N/A
N/A
N/A
Infineon
Infineon
Infineon
Infineon
N/A
MICRON
MICRON
MICRON
MICRON
N/A
N/A
ELPIDA
N/A
N/A
N/A
ELPIDA
ELPIDA
DS
DS
DS
SS
SS
SS
DS
DS
SS
DS
DS
SS
SS
DS
SS
DS
SS
SS
DS
SS
DIMM support
A B C
K4T51083QB-GCD5
K4T56083QF-GCD5
K4T56083QF-GCD5
HYB18T512800AC37
HYB18T512160AF-3.7
HYB18T512800AF37
HYB18T512800AF37
N/A
4FBIID9BQM
4JAIID9CRZ
4FBIID9CHM
4FBIID9CHM
E5108AB-5C-E
HYB18T512160AC-3.7
E5108AB-5C-E
HY5PS12821F-C4
HYMP564U64AP8-C3
HY5PS12821FP-C4
E5108AB-5C-E
E5108AB-5C-E
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DDR2 667 Qualified Vendors List
512MB Hynix
1024MB Hynix
512MB Hynix
256MB
256MB
512MB
256MB
MICRON
MICRON
Infineon
Infineon
1024MB Infineon
256MB ELPIDA
512MB ELPIDA
1024MB ELPIDA
HYMP564U64AP8-Y5
HYMP512U64AP8-Y4
HYMP564U64AP8-Y4
MT8HTF3264AY-667B5
MT8HTF3264AY-667B6
HYS64T64000HU-3S-A
HYS64T32000HU-3S-A
HYS64T128020HU-3S-A
EBE25UC8ABFA-6E-E
EBE51UD8AEFA-6E-E
EBE11UD8AEFA-6E-E
Hynix
Hynix
Hynix
MICRON
MICRON
Infineon
Infineon
Infineon
ELPIDA
ELPIDA
N/A
SS
SS
SS
SS
DS
SS
SS
DS
SS
SS
DS
DIMM support
A B C
HY5PS12821AFP-Y5
HY5PS12821AFP-Y4
HY5PS12821AFP-Y4
4SB42D9CZM
5FB42D9DPN
HYB18T512800AF3S
HYB18T512160AF-3S
HYB18T512800AF3S
E2508AB-GE-E
E5108AE-GE-E
N/A
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• configuration.
slots as one pair of Dual-channel memory configuration.
Dual-channel memory configuration.
2.5.2
Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components.
2
To install a DIMM:
1.
Unlock a DIMM socket by pressing the retaining clips outward.
2.
Align a DIMM on the socket such that the notch on the
DIMM matches the break on the socket.
3.
Firmly insert the DIMM into the socket until the retaining clips snap back in place and the
DIMM is properly seated.
1
3
• A DDR2 DIMM is keyed with a notch so that it fits in only one direction. Do not force a DIMM into a socket to avoid damaging the
DIMM.
• The DDR2 DIMM sockets do not support DDR DIMMs. DO not install
DDR DIMMs to the DDR2 DIMM sockets.
2.5.3
Removing a DIMM
To remove a DIMM:
1.
Simultaneously press the retaining clips outward to unlock the DIMM.
Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force.
2.
Remove the DIMM from the socket.
1
2
1
2.6
Installing an expansion card
In the future, you may need to install expansion cards. The motherboard has two PCI, one PCI Express™ x1, and one PCI Express™ x16 slot. The following sub-sections describe the slots and the expansion cards that they support.
x1 cards. You can only install low profile expansion cards on this system.
Ask your retailer for details.
2.6.1
Expansion slots
The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications.
This motherboard supports PCI Express x16 graphic cards that comply with the PCI Express specifications. The following figure shows a graphics card installed on the PCI Express x16 slot.
This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. The following figure shows a network card installed on the PCI Express x1 slot.
Before installing an expansion card, read the documentation that came with it and make the necessary hardware settings for the card.
2.6.2
Expansion card installation
Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage the motherboard.
To install an expansion card:
1.
Lay the system on its side on a flat and stable surface.
2.
Lift the expansion card lock to a
90º-100º angle.
2.
Remove the chassis support bracket.
3.
Remove the metal cover opposite the slot that you intend to use.
4.
Align the card connector with the slot and press firmly until the card is completely seated on the slot.
5.
If you have already installed a hard disk drive, replace the chassis support bracket; otherwise, install other components before replacing the chassis support bracket.
6.
Replace the expansion card lock to secure the card to the chassis.
6
7*
8
9*
0
1
2
4
10*
11*
12*
13
14*
System Timer
Keyboard Controller
Programmable Interrupt
Communications Port (COM1)
Floppy Disk Controller
Printer Port (LPT1)
System CMOS/Real Time Clock
ACPI Mode when used
IRQ Holder for PCI Steering
IRQ Holder for PCI Steering
PS/2 Compatible Mouse Port
Numeric Data Processor
Primary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
PCI slot 1
PCI slot 2
PCI Express x16 slot
PCI Express x1 slot1
Onboard USB controller 1
Onboard USB controller 2
Onboard USB controller 3
Onboard USB controller 4
Onboard USB 2.0 controller
Onboard LAN controller
Onboard Audio controller
— —
— — shared —
— shared
— —
—
—
—
— shared —
— —
— — shared —
— — — used
—
—
—
—
—
—
—
—
— shared — shared — —
—
—
—
—
—
—
—
—
—
—
—
—
— shared —
— — —
—
—
—
—
—
—
—
—
— — used
—
—
—
— —
— shared
—
—
—
—
— —
— shared
—
—
—
—
When using a PCI card on shared slots, ensure that the drivers support
“Share IRQ” or that the cards do not need IRQ assignments; otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable.
2.7
Installing an optical drive
The system comes with a 5.25-inch drive bay for an optical drive.
If you plan to install an IDE hard disk drive, set the optical drive as a slave device before installing it to the system. Refer to the optical drive documentation for details on how to set the drive as slave device.
To install an optical drive:
1.
Remove the front panel assembly following the instructions in section
“2.3.2 Removing the front panel assembly.”
2.
Drive a screw on the top right screw hole on both sides of the drive. The screw holes are approximately 5 cm from the drive front panel and 2 cm from the drive base.
3.
Lay the system on its side in a flat and stable surface.
4.
Carefully pull the IDE and audio cables and plugs out from the bay until the cables are long enough to connect to the drive.
5.
Connect the IDE cable to the IDE interface at the back of the drive. Match the red stripe on the cable with Pin 1 on the IDE interface.
6.
Connect the optical drive audio cable to the 4-pin connector at the back of the optical drive.
The IDE and audio plugs are pre-connected to the primary IDE and internal audio connectors on the motherboard. If you disconnected these plugs, refer to page 4-4 and 4-6 for their respective locations.
7.
Carefully push the optical drive all the way into the bay until the optical drive lock clicks.
8.
Connect a 4-pin power plug from the power supply unit to the power connector at the back of the drive.
In the future, you may have to upgrade or replace a defective optical drive.
To uninstall the optical drive:
1.
Remove the front panel assembly following the instructions in section
“2.3.2 Removing the front panel assembly”.
2.
Locate the optical drive screw lock.
3.
Push the lock to release the optical drive screw (A), then slightly pull the drive out from the bay (B).
4.
Disconnect the IDE, audio, and power cables and plugs from the back of the drive.
5.
Pull out the drive completely from the bay, then replace it following the instructions in the previous section.
2.8
Removing the card reader
In the future, you may have to remove or replace the 6-in-1 card reader.
To uninstall the card reader:
1.
Remove the front panel assembly following the instructions in “2.3.2
Removing the front panel assembly”.
2.
Locate the lock on both sides of the card reader assembly.
3.
Press the card reader lock inwards(A), then slightly pull the card reader assembly outward (B) until the USB cable and plug is exposed.
4.
Disconnect the USB cable and plug from the card reader assembly, then set the card reader assembly aside.
2.9
Installing hard disk drives (HDDs)
The system comes with two 3.5-inch drive bays (labeled 1 and 2) for installation of two Serial ATA hard disk drives or one IDE HDD (if you have installed an optical drive).
2.9.1
Hard disk drive bays
The drive bays incorporate a screw-less design that allows you to install and remove a hard disk drive without driving screws on the chassis. Each drive bay has a HDD screw lock and four screws rails (two on each side of the bay) that trap the HDD screws and secure the drive in the place.
2.9.2
SATA hard disk drive installation
To install a SATA hard disk drive:
1.
Insert the rubber washers to the HDD screws. Refer to the illustration on the right.
2.
Drive four screws (two on each side of the drive) on the drive screw holes.
3.
Connect one end of the supplied 7-pin SATA cable to the SATA connector at the back of the drive, then connect the other end to a
SATA connector on the motherboard. See page 4-5 for the location of the SATA connectors.
4.
Connect the 15-pin SATA power plug from the power supply unit to the power connector at the back of the drive.
5.
Place the HDD on the tray.
Make sure that the HDD screws are aligned with the screw holes and rails.
6.
When the HDD screws align with the screw rails, push the drive carefully until it is completely flushed on the bay.
The HDD screw lock clicks to indicate that the drive is properly in place.
2.9.3
IDE hard disk drive installation
Set the IDE HDD as master device before connecting the IDE cable and power plug. Refer to the HDD documentation for details.
To install an IDE hard disk drive:
1.
Follow steps 1 to 2 of the previous section.
2.
Connect the IDE cable (gray connector) to the IDE interface at the back of the drive. Match the red stripe on the cable with Pin 1 on the
IDE interface.
3.
Connect a power cable from the power supply unit to the power connector at the back of the drive.
4.
Follow steps 5 to 6 of the previous section to complete installation.
2.9.4
Uninstalling a hard disk drive
In the future, you may have to upgrade or replace a defective hard disk drive.
To uninstall the hard disk drive:
1.
Press the HDD screw lock (A), then push the drive out from the bay (B) until the drive screws are released from the screw rails.
2.
Slightly lift the HDD, then remove all plugs at the back of the drive.
3.
Install a new HDD following the instructions in the previous section.
2.10
Replacing the covers
After you install all the necessary components on the system, replace the covers following the instructions in this section:
To replace the front panel assembly:
1.
Hook the hinge-like tabs to the holes on the right side of the chassis.
2.
Swing the left edge of the front panel inward, then attach the front panel assembly hooks to the chassis until they snap in place.
Do not use too much force when replacing the front panel assembly.
To replace the metal chassis support:
1.
Reinstall the metal chassis support and the expansion card lock.
2.
Match and insert the hooks of the cover to the elongated holes on the side of the chassis. All eight hooks (four hooks on both sides) of the cover must properly fit the designated holes.
3.
Slide the cover toward the front panel until it is in place.
4.
Replace the cover screws.
2.11
Installing the foot stands
You need to install the foot stands to place the system vertically on your desktop.
To install the foot stands:
1.
Lay the system on its side on a flat, stable, and elevated surface, then locate two screw holes on the left side of the system.
2.
Extend the left side of the system at least 3 cm from the edge of the surface to facilitate installation.
3.
Align the foot stand and chassis screw holes.
4.
Drive in a screw to secure the footstand to the chassis.
5.
Follow the same procedures when installing the second foot stand.
The photo on the right shows the system in a vertical desktop placement.
2.12
Selecting the voltage
The system’s power supply unit has a 115 V/230 V voltage selector switch located beside the power connector. Use this switch to select the appropriate system input voltage according to the voltage supply in your area.
If the voltage supply in your area is 100-127 V, set the switch to 115 V.
If the voltage supply in your area is 200-240 V, set the switch to 230 V.
Setting the switch to 115 V in a 230 V environment will seriously damage the system!
Chapter 3
This chapter helps you power up the system and install drivers and utilities from the support CD.
3.1
Installing an operating system
This system supports Windows ® 2000/2003 Server/XP operating systems
(OS). Always install the latest OS version and corresponding updates to maximize the features of your system.
• Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
• Make sure that you install Windows ® 2000 Service Pack 4 or the
Windows ® XP Service Pack 1 or later versions before installing the drivers for better compatibility and system stability.
3.2
Support CD information
The support CD that came with the system package contains the drivers, software applications, and utilities that you can install to avail all system features.
The contents of the support CD are subject to change at any time without notice. Visit the ASUS website(www.asus.com) for updates.
3.2.1
Running the support CD
Place the support CD to the optical drive. The CD automatically displays the the support CD to locate the file ASSETUP.EXE from the BIN folder.
3.2.2
Drivers menu
The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices.
Launches the ASUS InstallAll driver installation wizard.
Installs the Quick Fix Engineering (QFE) driver updates.
Installs the Intel ® Chipset INF Update Program. This driver enables Plug-n-
Play INF support for the Intel ® chipset components on the motherboard.
When installed to the target system, this driver provides the method for configuring the chipset components.
You can install this utility using three different modes: interactive, silent, or unattended preload. Installing the driver in interactive mode requires user input during installation. User input is not required when installing the driver in silent or unattended preload modes. Refer to the online help or readme file that came with the utility for details.
Executes the wizard to install the Realtek ® ALC655 audio driver and application.
Installs the Intel ® Tekoa Ethernet driver.
Installs the USB 2.0 driver.
The screen display and drivers option may not be the same for different operating system versions.
3.2.3
Utilities menu
The Utilities menu shows the applications and other software that the motherboard supports.
Launches the ASUS InstallAll utilities installation wizard.
This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems. This utility helps you keep your computer in healthy operating condition.
The ASUS Update utility allows you to update the motherboard BIOS in a
Windows ® environment. This utility requires an Internet connection either through a network or an Internet Service Provider (ISP).
Installs the ASUS screen saver.
Installs the Adobe® Acrobat® Reader that allows you to open, view, and print documents in Portable Document Format (PDF).
Installs the USB 2.0 card reader software.
Installs the Microsoft® DirectX 9.0c driver. The Microsoft DirectX® 9.0c is a multimedia technology that enhances computer graphics and sound.
DirectX® improves the multimedia features of you computer so you can enjoy watching TV and movies, capturing videos, or playing games in your computer. Visit the Microsoft website (www.microsoft.com) for updates.
The anti-virus application scans, identifies, and removes computer viruses.
View the online help for detailed information.
The screen display and utilities option may not be the same for different operating system versions.
3.2.4
Manual item to open the folder of the user manual.
Most user manuals are in Portable Document Format (PDF). Install the
Adobe ® Acrobat ® Reader from the U t i l i t i e s m e n u user manual file.
3.2.5
ASUS contact information also find this information on the inside front cover of this user guide.
3.2.6
Other information
The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support CD. Click an icon to display the specified information.
Displays the general specifications of the motherboard.
Displays the support CD contents in graphical format.
Displays the ASUS Technical Support Request Form that you have to fill out when requesting technical support.
Displays the contents of the support CD and a brief description of each in text format.
Chapter 4
This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations.
4.1
Motherboard overview
PS/2KBMS
T: Mouse
B: Keyboard
COM1
ATX12V
LGA775
CPU_FAN
VGA
Bottom:
USB1
USB2
Top:
1394
LAN_USB34
Intel
®
GMCH
945G
AUDIO
Intel
82573L
CD
ALC882
PCIEX16
PCIEX1_1
PCI1
SB_PWR
PCI2
TI
TSB43AB22A
CR2032 3V
Lithium Cell
CMOS Power
AAFP SPDIF_OUT
IE1394_2 USB56 USB78
Intel
®
ICH7
CLRTC
Intel FWH
4Mb
SATA1 SATA2
BUZZ
4.2
Jumper
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS.
You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
To erase the RTC RAM:
1.
Turn OFF the computer and unplug the power cord.
2.
Remove the onboard battery.
3.
Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2.
4.
Reinstall the battery.
5.
Plug the power cord and turn ON the computer.
6.
Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure!
P5LD2-VM/S Clear RTC RAM
1 2
Normal
(Default)
CLRTC
2 3
Clear CMOS
4.3
Connectors
4.3.1
Rear panel connectors
Refer to section “1.3 Rear panel” for a description of the rear panel I/O ports.
4.3.2
Internal connectors
1 .
P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
This connector is for an Ultra DMA 100/66 signal cable. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If you install an optical drive and an IDE HDD, you must configure the optical drive as a slave device by setting its jumper accordingly. Refer to the optical drive or HDD documentation for the jumper settings.
• Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable.
• Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
PRI_IDE
NOTE: Orient the red markings
(usually zigzag) on the IDE ribbon cable to PIN 1.
IDE connector PIN 1
2 .
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives.
SATA1 SATA2
SATA connectors
• You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack1 before using Serial ATA hard disk drives.
• When using the connectors in standard IDE mode, you can connect the primary (boot) hard disk drive to any of the SATA connectors.
3 .
C P U f a n c o n n e c t o r ( 4 - p i n C P U _ F A N )
The fan connector supports cooling fans of 350 mA~740 mA (8.88 W max.) or a total of 1 A~2.22 A (26.64 W max.) at +12V. Connect the fan cable to the fan connector on the motherboard, making sure that the cable’s black wire matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors!
CPU_FAN
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
CPU fan connector
4 .
U S B c o n n e c t o r s ( 1 0 - 1 p i n U S B 5 6 , U S B 7 8 )
These connectors are for USB 2.0 ports. Connect the USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.
USB56
1
USB78
1
USB 2.0 connectors
Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!
5 .
O p t i c a l d r i v e a u d i o c o n n e c t o r ( 4 - p i n C D )
This connector is for the 4-pin audio cable that connects to the audio connector at the back of the optical drive.
CD audio connector
CD
Right Audio Channel
Ground
Ground
Left Audio Channel
6 .
A T X p o w e r c o n n e c t o r s ( 2 4 - p i n E A T X P W R ,
These connectors are for ATX power supply plugs. The plugs from the power supply are pre-connected to these connectors. If you have disconnected them during installation, find the proper orientation and push down the plugs firmly to the connectors until they fit.
ATX power connectors
ATX12V
GND
GND
+12V DC
+12V DC
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
Ground
+5 Volts
Ground
+5 Volts
Ground
+3 Volts
+3 Volts
EATXPWR
Ground
+5 Volts
+5 Volts
+5 Volts
-5 Volts
Ground
Ground
Ground
PSON#
Ground
-12 Volts
+3 Volts
• Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up.
• The system comes with a proprietary ATX 12 V Specification 2.0
power supply unit (PSU) with a minimum 275 W power rating.
7 .
F r o n t p a n e l a u d i o c o n n e c t o r ( 1 0 - 1 p i n A A F P 1 )
This connector supports the front panel audio I/O ports with either legacy AC’97 or High Definition Audio standard.
AAFP
Azalia compliant definition
Legacy AC’97 compliant definition
Analog front panel connector
We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s High Definition
Audio capability.
8 .
I E E E 1 3 9 4 aa
This connector supports the 4-pin IEEE 1394 port on the system front panel.
IEEE 1394 connector damage the motherboard!
IE1394_2
1
9 .
S y s t e m p a n e l c o n n e c t o r ( 1 0 - 1 p i n F _ P A N E L 1 )
This connector supports several chassis-mounted functions.
F_PANEL
PWRSW GND
PWR
PWR_LED-
PWRLED
PWR_LED+
Reset
Ground
IDE_LED-
IDE_LED+
RESET
IDE LED
* Requires an ATX power supply.
System panel connector
The sytem panel connector is color-coded for easy connection. Refer to the connector description below for details.
• S y s t e m p o w e r L E D ( G r e e n 2 - p i n P W R L E D )
This 3-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
• H a r d d i s k d r i v e a c t i v i t y L E D ( R e d 2 - p i n P W R L E D )
This 2-pin connector is for the HDD Activity LED. Connect the HDD
Activity LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD.
• A T X p o w e r b u t t o n / s o f t - o f f b u t t o n ( B l a c k 2 - p i n P W R S W )
This connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF.
• R e s e t b u t t o n ( B l u e 2 - p i n R E S E T )
This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power.
Chapter 5
This chapter tells how to change system settings through the BIOS
Setup menus and describes the
BIOS parameters.
5.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard
Basic Input/Output System (BIOS) setup.
1.
A S U S C r a s h F r e e B I O S 2 motherboard support CD when the BIOS file fails or gets corrupted.)
2.
A S U S U p d a t e ® environment.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file from the support CD to a USB floppy disk or flash disk in case you need to restore the BIOS in the future. You can copy the original motherboard BIOS using the ASUS
Update or AFUDOS utilities.
5.1.1
ASUS CrashFree BIOS 2 utility
The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD that contains the original or updated BIOS file.
Prepare the motherboard support CD containing the original or updated motherboard BIOS before using this utility.
To recover the BIOS:
1.
Remove any floppy disk from the floppy disk drive, then turn on the system.
2.
Insert the support CD to the optical drive.
3.
The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When no floppy disk is found, the utility automatically checks the optical drive for the original or updated BIOS file. The utility then updates the corrupted BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy not found!
Checking for CD-ROM...
CD-ROM found!
Reading file “P5LD2MQ.ROM”. Completed.
Start flashing...
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure!
4.
Restart the system after the utility completes the updating process.
The recovered BIOS may not be the latest BIOS version for this motherboard. Visit the ASUS website (www.asus.com) to download the latest BIOS file.
5.1.2
ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows ® environment. The ASUS Update utility allows you to:
• Save the current BIOS file
• Download the latest BIOS file from the Internet
• Update the BIOS from an updated BIOS file
• Update the BIOS directly from the Internet, and
• View the BIOS version information.
This utility is available in the support CD that comes with the motherboard package.
ASUS Update requires an Internet connection either through a network or an Internet Service Provider (ISP).
To install ASUS Update:
1.
Place the support CD in the optical drive. The D r i v e r s
2.
Click the U t i l i t i e s
3.
The ASUS Update utility is copied to your system.
Quit all Windows ® applications before you update the BIOS using this utility.
To update the BIOS through the Internet:
1.
Launch the ASUS Update utility from the Windows ® desktop by
2.
Select U p d a t e B I O S f r o m drop-down menu, then click
3.
Select the ASUS FTP site nearest you to avoid network
4.
From the FTP site, select the
BIOS version that you wish to
5.
Follow the screen instructions to complete the update process.
The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features.
To update the BIOS through a BIOS file:
1.
Launch the ASUS Update utility from the Windows ® desktop by
2.
Select U p d a t e B I O S f r o m a
3.
Locate the BIOS file from the
4.
Follow the screen instructions to complete the update process.
5.2
BIOS setup program
This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “ 5.1 Managing and updating your BIOS.”
Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup.” This section explains how to configure your system using this utility.
Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future. For example, you can enable the security password feature or change the power management settings. This requires you to reconfigure your system using the BIOS
Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the firmware hub.
The firmware hub on the motherboard stores the Setup utility. When you start up the computer, the system provides you with the opportunity to run this program. Press <Del> during the Power-On-Self-Test (POST) to enter the Setup utility; otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis.
You can also restart by turning the system off and then back on. Do this last option only if the first two failed.
The Setup program is designed to make it as easy to use as possible. Being a menu-driven program, it lets you scroll through the various sub-menus and make your selections from the available options using the navigation keys.
• The default BIOS settings for this motherboard apply for most conditions to ensure optimum performance. If the system becomes unstable after changing any BIOS settings, load the default settings
Menu.”
• The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.
• Visit the ASUS website (www.asus.com) to download the latest BIOS file for this motherboard.
5.2.1
BIOS menu screen
System Time
System Date
Primary IDE Master
Primary IDE Slave
Third IDE Master
Fourth IDE Master
IDE Configuration
System Information
:
:
:
:
[11:51:19]
[Tue 04/18/2006]
[ST320413A]
[Pioneer CD-ROM ATA]
[Not Detected]
[Not Detected]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select a field.
Use [+] or [-] to configure the System time.
5.2.2
Menu bar
The menu bar on top of the screen has the following main items:
For changing the basic system configuration
A d v a n c e d For changing the advanced system settings
For changing the advanced power management (APM) configuration
For changing the system boot configuration
For selecting the exit options and loading default settings
To select an item on the menu bar, press the right or left arrow key on the keyboard until the desired item is highlighted.
5.2.3
Navigation keys
At the bottom right corner of a menu screen are the navigation keys for that particular menu. Use the navigation keys to select items in the menu and change the settings.
Some of the navigation keys differ from one screen to another.
5.2.4
Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example, selecting
System Time
System Date
[11:51:19]
[Tue 04/18/2006]
Primary IDE Master : [ST320413A]
Primary IDE Slave : [Pioneer CD-ROM ATA]
Third IDE Master : [Not Detected]
Fourth IDE Master : [Not Detected]
IDE Configuration
System Information
Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.
Use [+] or [-] to configure the
System time.
The other items (Advanced, Power,
Boot, and Exit) on the menu bar have their respective menu items.
5.2.5
Sub-menu items
A solid triangle before each item on any menu screen means that the iteam has a sub-menu. To display the sub-menu, select the item and press
<Enter>.
5.2.6
Configuration fields
These fields show the values for the menu items. If an item is userconfigurable, you can change the value of the field opposite the item. You cannot select an item that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when selected. To change the value of a field, select it then press <Enter> to display a list of options. Refer to “5.2.7 Pop-up window.”
5.2.7
Pop-up window
Select a menu item then press <Enter> to display a pop-up window with the configuration options for that item.
5.2.8
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit on the screen.
Press the
Up/Down arrow keys or <Page Up> /
<Page Down> keys to display the other items on the screen.
5.2.9
General help
At the top right corner of the menu screen is a brief description of the selected item.
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections may cause system to malfunction.
Plug And Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster
[No]
[64]
[Yes]
[Disabled]
[Enabled]
5.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information.
Refer to section “5.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them.
System Time
System Date
Primary IDE Master
Primary IDE Slave
Third IDE Master
Fourth IDE Master
IDE Configuration
System Information
:
:
:
:
[11:51:19]
[Tue 04/18/2006]
[ST320413A]
[Pioneer CD-ROM ATA]
[Not Detected]
[Not Detected]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select a field.
Use [+] or [-] to configure the System time.
5.3.1
System Time [xx:xx:xx]
Allows you to set the system time.
5.3.2
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
5.3.3
Primary IDE Master/Slave;
While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item, then press <Enter> to display the IDE device information.
Select the type of device connected to the system.
Primary IDE Master
Device
Vendor
Size
LBA Mode
Block Mode
PIO Mode
Async DMA
: Hard Disk
: ST320413A
: 20.0GB
: Supported
: 16 Sectors
: 4
: MultiWord DMA-2
Ultra DMA : Ultra DMA-5
SMART Monitoring : Supported
Type
LBA/Large Mode
Block(Multi-sector Transfer) M
PIO Mode
DMA Mode[Auto]
Smart Monitoring
32Bit Data Transfer
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Disabled]
The BIOS automatically detects the values opposite the dimmed items
(Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra
DMA, and SMART monitoring). These values are not user-configurable.
These items show N/A if no IDE device is installed in the system.
Selects the type of IDE drive. Setting to Auto allows automatic selection of the appropriate IDE device type. Select CDROM if you are specifically configuring a CD-ROM drive. Select ARMD (ATAPI Removable Media Device) if your device is either a ZIP, LS-120, or MO drive.
Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]
Enables or disables the LBA mode. Setting to Auto enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA mode disabled. Configuration options: [Disabled]
[Auto]
Enables or disables data multi-sectors transfers. When set to Auto, the data transfer from and to the device occurs multiple sectors at a time if the device supports multi-sector transfer feature. When set to [Disabled], the data transfer from and to the device occurs one sector at a time.
Configuration options: [Disabled] [Auto]
Selects the PIO mode.
Configuration options: [Auto] [0] [1] [2] [3] [4]
Selects the DMA mode. Configuration options: [Auto] [SWDMA0]
[SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0]
[UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] [UDMA6]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Configuration options: [Auto] [Disabled] [Enabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
5.3.4
IDE Configuration
The items in this menu allow you to set or change the configurations for the IDE devices installed in the system. Select an item then press <Enter> if you want to configure the item.
IDE Configuration
Configure SATA As
Onboard IDE Operate Mode
Enhanced Mode Support On
IDE Detect Time Out (Sec)
[Standard IDE]
[Enhanced Mode]
[S-ATA]
[35]
Set SATA controller to
IDE mode.
Sets the Serial ATA configuration. The default option [Standard IDE] allows you to use your Serial ATA device like a Parallel ATA physical storage interface.
Allows selection of the IDE operation mode depending on the operating system (OS) that you installed. Set to Enhanced Mode if you are using native OS, such as Windows ® 2000/XP. Configuration options: [Disabled]
[Compatible Mode] [Enhanced Mode]
Enhanced Mode Support On [S-ATA]
The default setting SATA allows you to use native OS on Serial ATA and Parallel ATA ports. We recommend that you do not change the default setting for better OS compatibility. In this setting, you may
Serial ATA device.
The P-ATA+S-ATA and P-ATA options are for advanced users only. If you set to any of these options and encounter problems, revert to the mode] [P-ATA]
Combined Mode Option [Primary P-ATA + S-ATA]
Allows you to select the IDE ports to use. Configuration options:
[Primary P-ATA+S-ATA] [S-ATA only] [P-ATA only]
The S-ATA and P-ATA options are for advanced users only. If you set to any of these options and encounter problems, revert to the default setting [Primary P-ATA+S-ATA]. Configuration options: [S-ATA only]
[P-ATA only] [Primary P-ATA+S-ATA]
Selects the time out value for detecting ATA/ATAPI devices.
Configuration options: [0] [5] [10] [15] [20] [25] [30] [35]
5.3.5
System Information
This menu gives you an overview of the general system specifications. The
BIOS automatically detects the items in this menu.
AMIBIOS
Version
Build Date
Processor
Type
Speed
Count
:
:
0303
03/31/06
: Genuine Intel(R) CPU 3.20GHz
: 3200 MHz
: 1
System Memory
Total : 512MB
Appropriated : 0MB
Availabel : 512MB
Displays the auto-detected BIOS information.
Displays the auto-detected CPU specification.
Displays the auto-detected system memory.
5.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system devices.
Take caution when changing the settings of the Advanced menu items.
Incorrect field values can cause the system to malfunction.
Adjust system frequency/voltage
JumperFree Configuration
USB Configuration
CPU Configuration
Chipset
Onboard Devices Configuration
PCI PnP
5.4.1
JumperFree Configuration
JumperFree Configuration
AI Overclocking [Auto]
Select the target CPU frequency, and the relevant parameters will be auto-adjusted.
Frequencies higher than CPU manufacturer recommends are not guaranteed to be stable. If the system becomes unstable,
Allows selection of CPU overclocking options to achieve desired CPU internal frequency. Select either one of the preset overclocking configuration options: for stability when overclocking.
The following items appears only when you set the AI Overclocking item to [Manual].
Displays the frequency sent by the clock generator to the system bus and
PCI bus. The value of this item is auto-detected by the BIOS. Use the <+> and <-> keys to adjust the CPU frequency. You can also type the desired
CPU frequency using the numeric keypad. The values range from 133 to
199.
Allows you to set the DDR operating frequency.
Configuration options: [Auto] [DDR2-400MHz] [DDR2-533MHz]
Allows you to set the PCI Express frequency. This item is set to [Auto] by default. Configuration options: [Auto] [90] [91] ~ [150]
Allows you to select the PCI clock synchronization mode.
Configuration options: [To PCI Express] [Fixed 33.33MHz] [Fixed 36.3MHz]
[Fixed 40.0MHz]
Allows you to select the DDR2 reference voltage. Configuration options:
[Auto] [1.812V] [1.904V]
Refer to the DDR2 documentation before adjusting the memory voltage.
Setting a very high memory voltage may damage the memory module(s)!
Allows you to select the chipset voltage of the memory controller hub
(MCH). Configuration options: [Auto][1.50V] [1.60V] [1.70V]
Allows you to select the CPU VCore voltage. Configuration options:
[Auto][1.7000V] [1.6875V] [1.6750V] [1.6625V] [1.6500V] [1.6375V]
[1.6250V] [1.6125V] [1.6000V] [1.5875V] [1.5750V] [1.5625V]
[1.5500V] [1.5375V] [1.5250V] [1.5125V] [1.5000V] [1.4875V]
[1.4750V] [1.4625V] [1.4500V] [1.4375V] [1.4250V] [1.4125V]
[1.4000V] [1.3875V] [1.3750V] [1.3625V] [1.3500V] [1.3375V]
[1.3250V] [1.3125V] [1.3000V] [1.2875V]
Refer to the CPU documentation before setting the CPU Vcore voltage.
Setting a high Vcore voltage may damage the CPU!
to [Overclock Profile].
Allows you to overclock the CPU speed through the available preset values.
Configuration options: [Overclock 5%] [Overclock 10%] [Overclock 15%]
[Overclock 20%] [Overclock 30%]
5.4.2
USB Configuration
The items in this menu allows you to change the USB-related features.
Select an item then press <Enter> to display the configuration options.
Enables USB host controllers.
USB Configuration
Module Version - 2.24.0-10.4
USB Devices Enabled: None
USB Function
Legacy USB Support
USB 2.0 Controller
USB 2.0 Controller Mode
BIOS EHCI Hand-Off
[8 USB Ports]
[Enabled]
[Enabled]
[HiSpeed]
[Enabled]
The Module Version and USB Devices Enabled items show the auto-detected values. If no USB device is detected, the item shows None.
Disables the USB host controllers or specifies the number of enabled USB ports. Configuration options: [Disabled] [2 USB Ports] [4 USB Ports]
[6 USB Ports] [8 USB Ports]
Allows you to enable or disable support for legacy USB devices. Setting to
[Auto] allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Configuration options: [Disabled] [Enabled] [Auto]
Allows you to disable the USB 2.0 controller, or specify the number of ports to enable Configuration options: [Enabled] [Disabled]
Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or
FullSpeed (12 Mbps). Configuration options: [HiSpeed ] [FullSpeed ]
Allows you to enable support for operating systems without an EHCI hand-off feature. Configuration options: [Disabled] [Enabled]
5.4.3
CPU Configuration
The items in this menu show the CPU-related information that the BIOS automatically detects.
Configure Advanced CPU settings
Manufacturer: Intel
Brand String: Genuine Intel(R) CPU 3.20GHz
Frequency : 3200 MHz
FSB Speed : 800 MHz
Cache L1 : 16 KB
Cache L2 : 1024 KB
Cache L3 : 0 KB
Ratio Status: Unlocked (Max:22, Min:14)
Ratio Actual Value : 16
Ratio CMOS Setting:
VID CMOS Setting:
Microcode Updation:
[ 28]
[ 62]
[Enabled]
Max CPUID Value Limit:
Execute Disable Function
[Disabled]
[Disabled]
CPU Internal Thermal Control [Auto]
Sets the ratio between
CPU Core Clock and the
FSB Frequency.
NOTE: If an invalid ratio is set in CMOS then actual and setpoint values may differ.
Sets the ratio between the CPU Core Clock and the Front Side Bus frequency. The default value of this item is auto-detected by BIOS. Use the
Allows you to set the VID CMOS setting at which the processor is to run.
Enables or disables microcode updation.
Configuration options: [Disabled] [Enabled]
Enable this item to boot legacy operating systems that cannot support
CPUs with extended CPUID functions. Configuration options: [Disabled]
[Enabled]
Allows you to enable or disable the No-Execution Page Protection
Technology. Setting this item to [Enabled] forces the XD feature flag to always return to zero (0). Configuration options: [Disabled] [Enabled]
Disables or sets the CPU internal thermal control.
Configuration options: [Auto] [Disabled]
The following item appears only when you installed an Intel ® Pentium ® 4
CPU that supports the Hyperthreading Technology and Enhanced Intel
SpeedStep ® Technology (EIST).
Allows you to enable or disable the processor Hyper-Threading Technology.
Refer to the Appendix for more information on the Hyper-Threading
Technology. Configuration options: [Disabled] [Enabled]
Allows you to use the Enhanced Intel SpeedStep ® Technology. When set to
[Automatic], you can adjust the system power settings in the operating system to use the EIST feature.
Set this item to [Maximum] or [Disabled] if you do not want to use the EIST.
The CPU constantly operates at a lower internal frequency when you set this item to [Minimum].
Configuration options: [Maximum] [Minimum] [Automatic] [Disabled]
5.4.4
Chipset
The Advanced Chipset Settings menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu.
Advanced Chipset Settings
Configure DRAM Timing by SPD [Enabled]
Graphic Adapter Priority [PCI Express/Int-VG]
Internal Graphics Mode Select [Disabled]
Enable or disable DRAM timing by SPD.
When this item is enabled, the DRAM timing parameters are set according to the DRAM SPD (Serial Presence Detect). When disabled, you can manually set the DRAM timing parameters through the DRAM sub-items.
The following sub-items appear when this item is Disabled. Configuration options: [Disabled] [Enabled]
DRAM CAS# Latency [5 Clocks]
Controls the latency between the SDRAM read command and the time the data actually becomes available.
Configuration options: [6 Clocks] [5 Clocks] [4 Clocks] [3 Clocks]
DRAM RAS# Precharge [4 Clocks]
Controls the idle clocks after issuing a precharge command to the DDR
SDRAM. Configuration options: [2 Clocks] ~ [6 Clocks]
DRAM RAS# to CAS# Delay [4 Clocks]
Controls the latency between the DDR SDRAM active command and the read/write command. Configuration options: [2 Clocks] ~ [6 Clocks]
DRAM RAS# Activate to Precharge Delay [15 Clocks]
Configuration options: [4 Clocks] ~ [18 Clocks]
DRAM Write Recovery Time [4 Clocks]
Configuration options: [2 Clocks] ~ [6 Clocks]
Allows selection of the graphics controller to use as primary boot device.
Configuration options: [Internal VGA] [PCI Express/Int-VGA]
[PCI Express/PCI] [PCI/PCI Express] [PCI/Int-VGA]
Allows user to select the amount of system memory pre-allocated by the internal graphics device. Configuration options: [Disabled] [Enabled, 1MB]
[Enabled, 4MB] [Enabled, 8MB] [Enabled, 16MB] [Enabled, 32MB]
5.4.5
Onboard Devices Configuration
Configure W83627EHG Super IO Chipset
HD Audio Controller
Onboard 1394 Controller
Onboard PCIEX GbE LAN
LAN Option ROM
[Enabled]
[Enabled]
[Enabled]
[Disabled]
Serial Port1 Address
Parallel Port Address
Parallel Port Mode
ECP Mode DMA Channel
Parallel Port IRQ
[3F8/IRQ4]
[378]
[ECP]
[DMA3]
[IRQ7]
Enable or disable the
High Definition Audio
Controller.
Enables or disables the High Definition Audio controller.
Configuration options: [Enabled] [Disabled]
Allows you to enable or disable the onboard IEEE 1394 controller.
Configuration options: [Disabled] [Enabled]
Allows you to enable or disable the onboard PCI Express Gigabit LAN controller. Configuration options: [Disabled] [Enabled]
LAN Option ROM [Disabled]
Allows you to enable or disable the LAN option ROM in the onboard
LAN controller. This item appears only when the Onboard PCIE GbE
LAN item is set to Enabled. Configuration options: [Disabled]
[Enabled]
Allows you to select the Serial Port1 base address.
Configuration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4]
[2E8/IRQ3]
Allows you to select the Parallel Port base addresses.
Configuration options: [Disabled] [378] [278] [3BC]
Allows you to select the Parallel Port mode.
Configuration options: [Normal] [Bi-directional] [EPP] [ECP]
ECP Mode DMA Channel [DMA3]
This item appears only when the Parallel Port Mode is set to [ECP].
Allows you to set the Parallel Port ECP DMA.
Configuration options: [DMA0] [DMA1] [DMA3]
EPP Version [1.9]
Allows selection of the Parallel Port EPP version. This item appears
Configuration options: [1.9] [1.7]
Parallel Port IRQ [IRQ7]
Allows selection of the Parallel Port IRQ.
Configuration options: [IRQ5] [IRQ7]
5.4.6
PCI PnP
The PCI PnP menu items allow you to change the advanced settings for
PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices.
Take caution when changing the settings of the PCI PnP menu items.
Incorrect field values can cause the system to malfunction.
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Plug And Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
[No]
[64]
[Yes]
[Disabled]
[Enabled]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
Available: Specified
IRQ is available to be used by PCI/PnP devices.
Reserved: Specified IRQ is reserved for use by
Legacy ISA devices.
When set to [No], BIOS configures all the devices in the system. When set to [Yes] and if you install a Plug and Play operating system, the operating system configures the Plug and Play devices not required for boot.
Configuration options: [No] [Yes]
Allows you to select the value in units of PCI clocks for the PCI device latency timer register. Configuration options: [32] [64] [96] [128] [160]
[192] [224] [248]
When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the
PCI VGA card even if requested. Configuration options: [No] [Yes]
When set to [Enabled], the palette snooping feature informs the PCI devices that an ISA graphics device is installed in the system so that the latter can function correctly. Configuration options: [Disabled] [Enabled]
Allows BIOS to use PCI bus mastering when reading/writing to IDE devices.
Configuration options: [Disabled] [Enabled]
Allows you to set the PCI slot number holding a PCI IDE card that requires you to set the slot number. Configuration options: [Auto] [PCI Slot1]
[PCI Slot2] [PCI Slot3] [PCI Slot4] [PCI Slot5] [PCI Slot6]
When set to [PCI Device], the specific IRQ is free for use of PCI/PnP devices. When set to [Reserved], the IRQ is reserved for legacy ISA devices. Configuration options: [PCI Device] [Reserved]
5.5
Power menu
The Power menu items allow you to change the settings for the Advanced
Power Management (APM) and Advanced Configuration and Power Interface
(ACPI). Select an item then press <Enter> to display the configuration options.
Suspend Mode
Repost Video on S3 Resume
ACPI 2.0 Support
ACPI APIC Support
APM Configuration
Hardware Monitor
[Auto]
[Disabled]
[No]
[Enabled]
Select the ACPI state used for System
Suspend.
5.5.1
Suspend Mode [Auto]
Allows you to select the Advanced Configuration and Power Interface
(ACPI) state to be used for system suspend.
Configuration options: [S1 (POS) Only] [S3 Only] [Auto]
5.5.2
Repost Video on S3 Resume [Disabled]
Determines whether to invoke VGA BIOS post on S3/STR resume.
Configuration options: [Disabled] [Enabled]
5.5.3
ACPI 2.0 Support [No]
Allows you to add more tables for Advanced Configuration and Power
Interface (ACPI) 2.0 specifications. Configuration options: [No] [Yes]
5.5.4
ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Configuration and Power
Interface (ACPI) support in the Advanced Programmable Interrupt
Controller (APIC). When set to Enabled, the ACPI APIC table pointer is included in the RSDT pointer list. Configuration options: [Disabled]
[Enabled]
5.5.5
APM Configuration
APM Configuration
Power Button Mode
Restore on AC Power Loss
Power On By RTC Alarm
Power On By External Modems
Power On By PCI Devices
Power On By PCIE Devices
[On/Off]
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Go into On/Off, or
Suspend when Power button is pressed.
Allows the system to go into On/Off mode or suspend mode when the power button is pressed. Configuration options: [On/Off] [Suspend]
When set to Power Off, the system goes into off state after an AC power loss. When set to Power On, the system goes on after an AC power loss.
When set to Last State, the system goes into either off or on state, whatever the system state was before the AC power loss.
Configuration options: [Power Off] [Power On] [Last State]
Allows you to enable or disable RTC to generate a wake event. When this item is set to Enabled, the items RTC Alarm Date, RTC Alarm Hour, RTC
Alarm Minute, and RTC Alarm Second appear with set values. Configuration options: [Disabled] [Enabled]
This allows either settings of [Enabled] or [Disabled] for powering up the computer when the external modem receives a call while the computer is in
Soft-off mode. Configuration options: [Disabled] [Enabled]
The computer cannot receive or transmit data until the computer and applications are fully running. Thus, connection cannot be made on the first try. Turning an external modem off and then back on while the computer is off causes an initialization string that turns the system power on.
When set to [Enabled], this parameter allows you to turn on the system through a PCI device. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled]
[Enabled]
When set to [Enabled], this parameter allows you to turn on the system through a PCI Express device. Configuration options: [Disabled] [Enabled]
5.5.6
Hardware Monitor
Hardware Monitor
CPU Temperature
MB Temperature
CPU Fan Speed (RPM)
CPU Q-Fan Control
VCORE Voltage
3.3V Voltage
5V Voltage
12V Voltage
[51ºC/122.5ºF]
[41ºC/105.5ºF]
[3813 RPM]
[Disabled]
[ 1.320V]
[ 3.345V]
[ 5.094V]
[11.880V]
CPU Temperature
The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures. Select Disabled if you do not wish to display the detected temperatures.
The onboard hardware monitor automatically detects and displays the CPU fan speed in rotations per minute (RPM). If the fan is not connected to the motherboard, the field shows N/A.
Allows you to enable or disable the ASUS Q-Fan feature that smartly adjusts the fan speeds for more efficient system operation.
Configuration options: [Disabled] [Enabled]
The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators.
5.6
Boot menu
The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu.
Boot Settings
Boot Device Priority
Boot Settings Configuration
Security
Specifies the Boot
Device Priority sequence
5.6.1
Boot Device Priority
Boot Device Priority
1st Boot Device
2nd Boot Device
3rd Boot Device
[Removable Dev.]
[PM-ST330620A]
[PS-Pioneer CD-ROM]
These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system.
Configuration options: [xxxxx Drive] [Disabled]
5.6.2
Boot Settings Configuration
Boot Settings Configuration
Quick Boot
Full Screen Logo
AddOn ROM Display Mode
Bootup Num-Lock
PS/2 Mouse Support
Wait For ‘F1’ If Error
Hit ‘DEL’ Message Display
Interrupt 19 Capture
[Enabled]
[Enabled]
[Force BIOS]
[On]
[Auto]
[Enabled]
[Enabled]
[Disabled]
Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items.
Configuration options: [Disabled] [Enabled]
This allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
Set this item to [Enabled] to use the ASUS MyLogo™ feature.
Sets the display mode for option ROM.
Configuration options: [Force BIOS] [Keep Current]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
Allows you to enable or disable support for PS/2 mouse.
Configuration options: [Disabled] [Enabled] [Auto]
When set to Enabled, the system waits for the F1 key to be pressed when error occurs. Configuration options: [Disabled] [Enabled]
When set to Enabled, the system displays the message “Press DEL to run
Setup” during POST. Configuration options: [Disabled] [Enabled]
When set to [Enabled], this function allows the option ROMs to trap
Interrupt 19. Configuration options: [Disabled] [Enabled]
5.6.3
Security
The Security menu items allow you to change the system security settings.
Select an item then press <Enter> to display the configuration options.
Security Settings
Supervisor Password : Not Installed
User Password : Not Installed
Change Supervisor Password
<Enter> to change password.
<Enter> again to disabled password.
Select this item to set or change the supervisor password. The Supervisor
To set a Supervisor Password:
1.
Select the Change Supervisor Password item and press <Enter>.
2.
From the password box, type a password composed of at least six letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message “Password Installed” appears after you successfully set your password.
To change the supervisor password, follow the same steps as in setting a user password.
To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message “Password Uninstalled” appears.
If you forget your BIOS password, you clear it by erasing the CMOS Real
Time Clock (RTC) RAM. See section “4.2 Jumpers” for information on how to erase the RTC RAM.
After you have set a supervisor password, the other items appear to allow you to change other security settings.
Security Settings
Supervisor Password : Not Installed
User Password : Not Installed
Change Supervisor Password
User Access Level
Change User Password
Clear User Password
Password Check
[Full Access]
[Setup]
This item allows you to select the access restriction to the Setup items.
Configuration options: [No Access] [View Only] [Limited] [Full Access]
Time.
utility.
Select this item to set or change the user password. The User Password
To set a User Password:
1.
Select the Change User Password item and press <Enter>.
2.
On the password box that appears, type a password composed of at least six letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message “Password Installed” appears after you set your password successfully.
To change the user password, follow the same steps as in setting a user password.
Select this item to clear the user password.
When set to [Setup], BIOS checks for user password when accessing the
Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system.
Configuration options: [Setup] [Always]
5.7
Exit menu
The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items.
Exit Options
Exit & Save Changes
Exit & Discard Changes
Discard Changes
Load Setup Defaults
Pressing <Esc> does not immediately exit this menu. Select one of the options from this menu or <F10> from the legend bar to exit.
Once you are finished making your selections, choose this option from the
Exit menu to ensure the values you selected are saved to the CMOS RAM.
An onboard backup battery sustains the CMOS RAM so it stays on even when the PC is turned off. When you select this option, a confirmation
If you attempt to exit the Setup program without saving your changes, the program prompts you with a message asking if you want to save your changes before exiting. Press <Enter> to save the changes while exiting.
Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to fields other than
System Date, System Time, and Password, the BIOS asks for a confirmation before exiting.
This option allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears.
This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you saving the values to the non-volatile RAM.
Appendix
The Appendix describes the CPU features and technologies that the system supports.
A.1
Intel ® EM64T
• The motherboard is fully compatible with Intel ® Pentium ® 4 LGA775 processors running on 32-bit operating systems.
• The motherboard comes with a BIOS file that supports EM64T. You can download the latest BIOS file from the ASUS website
(www.asus.com/support/download/) if you need to update the BIOS file. See Chapter 5 for details.
• Visit www.intel.com for more information on the EM64T feature.
• Visit www.microsoft.com for more information on Windows ® 64-bit OS.
Using the Intel ®
To use the Intel ® EM64T feature:
1.
Install an Intel ® Pentium ® 4 CPU that supports the Intel ® EM64T.
2.
Install a 64-bit operating system (Windows ® XP Professional x64
Edition or Windows ® Server 2003 x64 Edition).
3.
Install the 64-bit drivers for the motherboard components and devices from the support CD.
4.
Install the 64-bit drivers for expansion cards or add-on devices, if any.
Refer to the expansion card or add-on device(s) documentation, or visit the related website, to verify if the card/device supports a 64-bit system.
A.2
Enhanced Intel SpeedStep ®
Technology (EIST)
• The motherboard comes with a BIOS file that supports EIST. You can download the latest BIOS file from the ASUS website
(www.asus.com/support/download/) if you need to update the
BIOS. See Chapter 5 for details.
• Visit www.intel.com for more information on the EIST feature.
A.2.1
System requirements
Before using EIST, check your system if it meets the following requirements:
• Intel ® Pentium ® 4 processor with EIST support
• BIOS file with EIST support
• Operating system with EIST support (Windows ® XP SP2/Windows ®
Server 2003 SP1/Linux 2.6 kernel or later versions)
A.2.2
Using the EIST
To use the EIST feature:
1.
Turn on the computer, then enter the BIOS Setup.
2.
Go to the Advanced Menu then press <Enter>.
3.
Set the Intel(R) SpeedStep Technology then press <Enter>. See page 5-19 for details.
4.
Press <F10> to save your changes and exit the BIOS setup.
5.
After the computer restarts, right click on a blank space on the desktop,
6.
When the Display Properties window appears, click the
7.
Click the Power
Monitor power section to open
8.
On the Power schemes click , then select any option
9.
A p p l y window.
After you adjust the power scheme, the CPU internal frequency slightly decreases when the CPU loading is low.
The screen displays and procedures may vary depending on the operating system.
A.3
Intel ® Hyper-Threading Technology
• The motherboard supports Intel ® Pentium ® 4 LGA775 processors with Hyper-Threading Technology.
• Hyper-Threading Technology is supported under Windows ® XP/2003
Server and Linux 2.4.x (kernel) and later versions only. Under Linux, use the Hyper-Threading compiler to compile the code. If you are using any other operating systems, disable the Hyper-Threading Techonology item in the BIOS to ensure system stability and performance.
• Installing Windows ® XP Service Pack 1 or later version is recommended.
• Make sure to enable the Hyper-Threading Technology item in BIOS before installing a supported operating system.
• For more information on Hyper-Threading Technology, visit www.intel.com/info/hyperthreading.
To use the Hyper-Threading Technology:
1.
Install an Intel ® Pentium ® 4 CPU that supports Hyper-Threading
Technology.
2.
Power up the system and enter the BIOS Setup. Under the A d v a n c e d
The BIOS item appears only if you installed a CPU that supports
Hyper-Threading Techonology.
3.
Restart the computer.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement