Mitsubishi Electric MR-385C Specifications

SERVO AMPLIFIERS & MOTORS
Apply servos to all machines with
Easy To Use
Advanced One-Touch Tuning
Servo gains are adjusted with one-touch ease without a
personal computer.
Tolerance against Instantaneous Power Failure
The instantaneous power failure tough drive function and the
large capacity capacitor reduce machine downtime.
Large Capacity Drive Recorder
Servo data before and after the alarm occurrence are stored
in non-volatile memory for quick and accurate analysis of the
alarm occurrence.
reliable basic performance and advanced ease-of-use!
High Performance
Global Standard
Fast and Accurate
Compliance to Global Standards
2.0 kHz, shortening the tact time.
as standard.
High Resolution Encoder
Sink and Source Connections
incremental encoder, achieving high accuracy.
with both sink and source type connections.
Energy Conservation
Global Support
regenerative energy to be used effectively, reducing energy
services to support users.
The dedicated engine enables speed frequency response of
The servo motor is equipped with 131072 pulses/rev (17-bit)
The large capacity main circuit capacitor allows the
consumption.
Global servo, MR-JE series, complies with global standards
Digital input/output is compatible
FA Centers located throughout the world provide attentive
W i t h M i t s u b i s h i ’s c o m m i t m e n t t o t o t a l s y s t e m s o l u t i o n s
t h e M E L S E RVO - J E b e c o m e s t h e a n s w e r t o t h e w o r l d - w i d e
To satisfy your needs of advanced driving control systems, Mitsubishi Electric provides an extensive range of automation
and servo motors to programmable controllers, positioning modules, Human Machine Interfaces and highly developed
With our global support network which provides attentive services including product purchases, after-sales services,
we assure you the maximum performance of MELSERVO-JE throughout the world.
HUMAN MACHINE I/F
Graphic Operation Terminal
SOFTWA RE
PC/AT compatible computer
GOT1000 series
C ON T R O L L E R
Programmable controller
MELSEC
F series
MELSEC
Q series
MELSEC
L series
Positioning module
QD75P1/2/4N
QD75D1/2/4N
FX2N-10PG
FX3U-1PG
QD70P4/8
QD70D4/8
LD75P1/2/4
LD75D1/2/4
Pulse train input
IN T ERFA C E
S ERVO A M PL I F I E R
LOW-VOLTAGE S WIT CH
Servo amplifier
General-purpose interface compatible
MR-JE-A
SERVO M O TO R
Small capacity,
low inertia
Medium capacity,
medium inertia
Capacity: 100 to 750 W
Capacity: 0.5 to 3 kW
HF-KN series
LINEUP
SOLUTION
Servo motor
HF-SN series
Servo amplifier
Model
MR-JE-_A
●:Compatible
Power supply
specifications
Rated output [kW]
3-phase 200 V AC
0.1, 0.2, 0.4, 0.6,
0.75, 1, 2, 3
Command interface
Pulse train
●
Analog voltage Position
●
Servo motor
Control mode
●
Speed
Torque
●
●
Series
Rated speed
[r/min]
HF-KN series
3000
HF-SN series
2000
1. The maximum speed of HF-SN302J
*
Easy To Use
and global suppor ts,
High Performance Global Standard
need s i n d r iv i ng cont rol.
products from servo amplifiers
solutions.
technical consulting, and practical training,
PLC engineering software
Servo setup software
INDEX
MELSOFT GX
Works2
MELSOFT MR
Configurator2
Easy To Use
Capacity selection software
High Performance
Global Standard
GEAR
Magnetic
contactor
Molded-case
circuit breaker
Product Specifications
MS-T
Easy Adjustments
p. 5
Improved Tolerance against
Instantaneous Power Failure
p. 6
Maintenance Functions
p. 7
Servo Motors
p. 8
Servo Setup Software
(MR Configurator2)
p. 9
Fast and Accurate
p. 11
Energy Conservation
p. 12
Global Standards
p. 13
Global FA Centers
p. 14
Servo Amplifiers
p. 1-1
Servo Motors
p. 2-1
Options/Peripheral Equipment
p. 3-1
LVS/Wires
p. 4-1
Product List
p. 5-1
Cautions
p. 6-1
WS-V
Mitsubishi Electric’s integrated FA solution for achieving
seamless information collaboration between information
systems and control systems, and enabling lateral
integration of production sites.
Mitsubishi Electric’s integrated FA platform for achieving
lateral integration of controllers & HMI, engineering
environments and networks at production sites.
Maximum speed
[r/min]
4500
0.1, 0.2, 0.4, 0.75
3000/2500*1
is 2500 r/min.
Rated output
[kW]
*
●:Available
With electromagnetic brake
(B)
Oil seal
(J)
●
●
●
●
0.5, 1, 1.5, 2, 3
IP rating*2
IP65
IP67
2. The shaft-through portion is excluded.
4
Easy To Use
Fast, Trouble-Free Setup
Mitsubishi Electric’s unique “Advanced one-touch tuning” enables servo gain adjustment with one-touch ease.
The improved tolerance against instantaneous power failure, the ease of maintenance, and the simple setup
software would add further usability for all MELSERVO-JE users.
H i g h - P r e c i s i o n
T u n i n g
Servo gain adjustment with one-touch ease
Advanced One-Touch Tuning Function
Servo gains including machine resonance suppression filter, advanced vibration suppression control II*, and robust filter are
adjusted just by pressing the buttons on the front of the servo amplifier. Machine performance is utilized to the fullest using the
advanced vibration suppression control function.
* The advanced vibration suppression control II automatically adjusts one frequency.
Vibration suppression
control and robust filter
adjustment with one-touch.
: Actual operation
Speed
Speed
Before
Settling
time
Time
Time
Operation is unstable.
Settling
time
After
Exactly matched.
High-speed
positioning.
Speed
: Command
Adjust the servo gains just by
pressing the buttons on the
front of the servo amplifier.
Time
Operation is not following
the command.
Suppress two types of low frequency vibrations at once
Advanced Vibration Suppression Control II
Patent
pending
Due to vibration suppression algorithm which supports three-inertia system, two types of low frequency vibrations are suppressed
at the same time. Adjustment is performed on MR Configurator2.
This function is effective in suppressing vibration at the end of an arm and in reducing residual vibration in a machine.
Three-inertia
system
Vibration at the end
of an arm
Without vibration
suppression control
Advanced vibration
suppression control
Advanced vibration
suppression control II
Droop pulses
Vibration in
a machine
5
Two types of
the vibrations are
suppressed at
the same time.
Torque
Speed command
Easy To Use
High Performance Global Standard
Applicable frequency range of 10 Hz to 4500 Hz
High responsivity and stability for high-inertia machines
Machine Resonance Suppression Filter
Robust Filter
With advanced filter structure, applicable frequency range is
expanded to between 10 Hz and 4500 Hz. Additionally, the
number of simultaneously applicable filters is increased to
five, improving vibration suppression performance of
machines.
Patent
pending
Achieving both high responsivity and stability was difficult with
the conventional control in high-inertia systems with belts and
gears such as printing and packaging machines. The MR-JE
series enables the high responsivity and the stability at the
same time without adjustment. The robust filter more
gradually reduces the torque with wide frequency range and
achieves more stability as compared to the prior model.
Machine with a high-inertia ratio
Applicable frequency range
Five filters are
settable in a range of
10 Hz to 4500 Hz.
Robust filter
10
Gain Conventional
low-pass filter
4500 [Hz]
100
Conventional control
With robust filter
Speed command
Droop pulses
Torque
Robust filter
Vibrating
Frequency
Stable
Inc reased Tolera n c e Ag a i n s t I n s ta n ta n e o u s P o w e r F a i l u r e
Reduce machine downtime
Capacity is
increased by 20%
Large Capacity Main Circuit Capacitor
Reduce undervoltage alarms
Instantaneous Power Failure Tough Drive
The tolerance against instantaneous power failure is improved
The possibility of undervoltage alarm is reduced by limiting
as compared to the prior model. The improved tolerance
the main circuit power supply.
by increasing the capacity of the main circuit capacitor by 20%
reduces machine downtime and then improves productivity.
The capacity of the main circuit
capacitor is increased,
improving the tolerance against
instantaneous power failure.
the torque when instantaneous power failure is detected in
Speed
Instantaneous
power failure
detected
Prior model
MR-JE series
Instantaneous
power failure
Reduce the possibility of
undervoltage alarm
by limiting the torque.
Time
6
E a s y
M o n i t o r i n g
a n d
M a i n t e n a n c e
Analyze cause of alarm
Large Capacity Drive Recorder
Patent
pending
● Servo data such as motor current and position command before and after the alarm occurrence are stored in non-volatile
memory of the servo amplifier. The data read on MR Configurator2 during restoration are used for cause analysis.
● This function allows to check the waveform of 16 alarms in the alarm history ((analog 16 bits × 7 channels + digital 8 channels)
× 256 points) and the monitor value.
Data are stored
in non-volatile
memory at alarm
occurrence.
Alarm No., waveform, and monitor
value at alarm occurrence are
displayed in MR Configurator2.
Data over certain
period of time are
stored in the memory.
Waveform display
Monitor value display
Lowered bus voltage
It is revealed that the main
circuit power is turned off.
Reduce machine downtime incurred by age-related deterioration
Vibration Tough Drive
Machine resonance suppression filter is readjusted
when vibration caused by a change in machine
resonance frequency is detected by the current
command inside the servo amplifier. This function
reduces losses from the machine downtime caused by
age-related deterioration.
7
Vibration
detected
Motor current
Suppresses vibration
by readjusting the machine
resonance suppression filter.
Easy To Use
High Performance Global Standard
Support optimal maintenance of driving parts
Machine Diagnosis Function
Patent
pending
This function detects changes of machine parts (ball screw, guide, bearing, belt, etc.) by analyzing machine friction, load moment of
inertia, unbalanced torque, and changes in vibration component from the data inside the servo amplifier, supporting timely maintenance
of the driving parts.
Machine information is
displayed and monitored.
[Monitoring with MR Configurator2]
Changes are detected by
automatically estimating
friction and vibration
inside the servo amplifier.
Particular measurement
and adjustment are not
required.
MR-JE-A
Personal
computer
Encoder
Servo motor
Ball screw
Easy troubleshooting
Three-Digit Alarm
MR-JE series displays the alarm No. in three digits
[Example of an alarm window on MR Configurator2]
to show the servo alarm in more details,
making troubleshooting easy.
[Three-digit alarm display]
The alarm No. shows
whether the undervoltage
alarm was caused by
instantaneous power
failure or by lowered bus
voltage in the servo amplifier.
U s e r - F r i e n d l y
M o t o r s
Even in severe environment
Cable leading in both ways
Improved Environment Safety
Selectable Cable Leading Direction
HF-KN series and HF-SN series are rated IP65 and IP67
The power cable, the encoder cable, and the electromagnetic
* The shaft-through portion is excluded.
direction of the load side, depending on the selected
respectively.
Protected from
water and dust.
brake cable are led out to either in direction of or in opposite
cables. (HF-KN series)
Selectable mounting direction
In direction
of load side
In opposite
direction of
load side
8
The easy-to-use design MR-JE series
makes startup and adjustment that simple.
Servo setup software
MR Configurator2
(SW1DNC-MRC2-E)
Tuning, monitor display, diagnosis, reading/writing parameters, and test operations are easily
performed on a personal computer.
This start-up support tool achieves a stable machine system, optimum control, and short setup time.
P r e p a r a t i o n
Just follow the guidance, and setup is complete
Supporting replacement from conventional system
Servo Assistant Function
Parameter Converter Function
Complete setting up the servo amplifier just by following
guidance displays. Setting parameters and tuning are easy
since related functions are called up from shortcut buttons.
With this function, parameter files for MR-E series or MR-E
Super series are converted to those for MR-JE series.
So simple!
Just follow
the guidance.
S e t t i n g
a n d
S t a r t - u p
Easy and fast parameter setting
Visible operation status and power consumption
Parameter Setting Function
Monitor Function
Display parameter setting in list or visual formats, and
set parameters by selecting from the drop down list. Set
in-position range in mechanical system unit (e.g. μm).
Parameter read/write time is approximately one tenth of the
conventional time.
Monitor operation status on the [Display all] window. Check
power consumption without any measurement equipment
such as electric power meter, assign input/output signals,
and monitor ON/OFF status on the [I/O monitor] window.
[Display all] window
Set without
manuals.
9
Display details of
relevant parameters
in a docking window.
[I/O monitor] window
Monitor without
measurement
equipment.
Easy To Use
S e r v o
High Performance Global Standard
A d j u s t m e n t
Tuning is just one click away
Fine tuning of loop gain
One-Touch Tuning Function
Tuning Function
Adjustments including estimating load to motor inertia ratio,
adjusting gain, and suppressing machine resonance are
automatically performed for the maximum servo performance
Manually adjust loop gain finely on the [Tuning] window
for further performance after the one-touch tuning.
just by clicking the start button. Check the adjustment results
of settling time and overshoot.
Pursue higher
performance
with manual
setting.
Easy adjustment
Click
Display
adjustment
results.
Adjust gains
finely.
Adjustment
completed
Display
adjustment
results.
More convenient with overwrite and graph history functions
Analyze the frequency characteristics
Graph Function
Machine Analyzer Function
The number of measurement channels is increased to 7 channels
Input random torque to the servo motor automatically and
statuses in the waveform at one measurement, supporting setting
machine system just by clicking the [Start] button. This
for analog, and 8 channels for digital. Display various servo
and adjustment. Convenient functions such as [Overwrite] for
overwriting multiple data and [Graph history] for displaying graph
history are available.
analyze frequency characteristics (0.1 Hz to 4.5 kHz) of a
function supports setting of machine resonance suppression
filter, etc.
Measure
mechanical
characteristics.
Check the servo
operation in
waveform.
M a i n t e n a n c e
For timely parts replacement
Find out the aging deterioration of your machines
Servo Amplifier Life Diagnosis Function
Machine Diagnosis Function
Check cumulative
operation time and on/off
times of inrush relay. This
function provides an
indication of replacement
time for servo amplifier
parts such as capacitor
and relays.
Support
the preventive
maintenance
of the servo
amplifier.
This function estimates and
displays machine friction and
vibration in normal operation
without any special
measurement.
Comparing the data of the
first operation and after years
of operation helps to find out
the aging deterioration of a
machine and is beneficial for
preventive maintenance.
Patent
pending
Prevent
machine failure
with advanced
preventive
maintenance
beforehand.
10
High Performance
Further Reduction of Tact Time
Top-level basic performance is achieved,
including speed frequency response of 2.0 kHz.
The MELSERVO-JE series that utilizes regenerative energy
maximizes the machine performance and energy saving.
F a s t
a n d
A c c u r a t e
Class top-level speed frequency response
Exact positioning
2.0 kHz Speed Frequency Response
High-Resolution Encoder
The top-level speed frequency response of 2.0 kHz shortens
The servo motor equipped with an incremental encoder of
machine.
and smooth rotation.
the settling time substantially, reducing the tact time of a
[Settling time comparison with the prior model]
131072 pulses/rev (17-bit) enables high-accuracy positioning
Prior motor speed
Motor speed
Speed
Speed command
Equipped with
high-resolution
incremental
encoder.
Shorter settling time
In-position signal
Settling time
Time
Further smooth operation
Smooth, constant-speed operation
Max Command Pulse Frequency of 4 Mpps
Reduced Torque Ripple during Conduction
MR-JE-A having a general-purpose interface is compatible
By optimizing the combination of the number of motor poles
enabling smooth operation.
greatly reduced. Smooth constant-velocity operation of a
with the maximum command pulse frequency of 4 Mpps,
Controller
Compatible with 4 Mpps.
MR-JE-A
and the number of slots, torque ripple during conduction is
machine is achieved.
■ Torque ripple
Prior servo motor
11
1/4
(As compared to the prior series.)
HF-KN series
Easy To Use
High Performance Global Standard
Compatible with pulse train and analog
Flexible Command Interface
The command interface of MR-JE-A is compatible with both pulse train command and analog voltage command. The MR-JE-A
servo amplifier enables positioning control with pulse train command, and speed and torque control with analog voltage command.
E c o - F r i e n d l y
P e r f o r m a n c e
Reduce waste in energy consumption
Efficient Utilization of Regenerative Energy
Capacity of the main circuit capacitor is increased by 20% as
Large amount of regenerative
energy is charged
in the capacitor.
compared to that of the prior model, and thus the charging
capacity is increased, enabling larger regenerative energy to
be reused as driving power energy. Additionally, because the
Regenerative
energy
control circuit and the main circuit use a common power
M
supply, the regenerative energy is also used for the control
circuit, reducing waste in energy consumption.
Power
supply
Servo motor
Control circuit
Visualize power consumption
Regenerative energy
is reused in the
control circuit.
Power Monitor
Driving power and regenerative energy are calculated in the
servo amplifier from the data such as speed and current, and
the power consumption is monitored with MR Configurator2.
Visualization of the power consumption helps to save energy.
MR-JE-A
Personal computer
Servo motor
Achieve further energy saving
Saving Energy with Advanced Technologies
Reducing energy loss of the servo amplifier
Configuring a driving
Efficiency is increased
by the use of a new
power module. Energy
loss of the servo
amplifier itself is
reduced.
Saving energy by improving machine performance
Reduced loss
system with the
high-performance MR-JE
Reduced machine
operation time
series servo amplifiers
and servo motors reduces
machine tact time and
operation time, achieving
energy conservation.
12
Global Standard
Fully Compliant Worldwide
To satisfy growing needs in driving control throughout the world,
the MR-JE series complies with global standards.
The digital input/output is compatible with both sink and source type connections.
G l o b a l
S e r v o
M e e t s
G l o b a l
S t a n d a r d s
Best quality all over the world
Conformity with Global Standards and Regulations
Use the MR-JE series globally. The servo amplifiers and the servo motors conform to global standards as standard.
Conformity with global standards and regulations
Low voltage directive
EMC directive
RoHS directive
European EC
directive
UL standard
CSA standard
Measures for Administration of the Pollution Control
of Electronic Information Products (Chinese RoHS)
China Compulsory Certification (CCC)
Korea Radio Wave Law (KC)
Servo amplifier
EN 61800-5-1
EN 61800-3
Compliant
UL 508C
CSA C22.2 No.14
Servo motor
EN 60034-1 / EN 60034-5
EN 60034-1
Compliant
UL 1004-1 / UL 1004-6
CSA C22.2 No.100
Compliant (optional cables and connectors)
Compliant (optional cables and connectors)
N/A
Compliant
N/A
N/A
*1. Refer to "Servo Amplifier Instruction Manual" and "EMC Installation Guidelines" when your system needs to meet the EMC directive.
*2. When exporting the product, follow the local laws and regulations.
Flexible connections for the global use
Sink and Source Connections
The digital input/output is compatible with both sink and source type connections.
■ Example of digital input
Current
Switch
Servo amplifier
EM2, etc.
DICOM
Current
Switch
Servo amplifier
EM2, etc.
DICOM
24 V DC
24 V DC
Sink input
13
Compatible with
sink and source
type connections.
Source input
Easy To Use
E x t e n s i v e
G l o b a l
High Performance Global Standard
S u p p o r t
N e t w o r k
Supporting MELSERVO users worldwide
Global FA Centers
Across the globe, FA Centers provide customers with local assistance for purchasing Mitsubishi Electric products and with
after-sales services. To enable national branch offices and local representatives to work together in responding to local needs, we
have developed a service network throughout the world. We provide repairs, on-site engineering support, and sales of
replacement parts. We also provide various services from technical consulting services by our expert engineers to practical
training for equipment operations.
UK FA Center
German FA Center
Russian FA Center
Beijing FA Center
European FA Center
Korean FA Center
Tianjin FA Center
Guangzhou FA Center
Czech Republic FA Center
India FA Center
Mitsubishi Electric Corp
North American FA Center
Shanghai FA Center
Taiwan FA Center
Thailand FA Center
ASEAN FA Center
Brazil FA Center
Shanghai, China
Shanghai FA Center
Taiwan
Left: Taiwan FA Center (Taipei) /
Right: Taiwan FA Center (Taichung)
Pune/Gurgaon/Bangalore,
India
Ratingen, Germany
India FA Center
German FA Center/
Europe Development Center
Beijing, China
Seoul, Korea
Chicago IL, U.S.A.
Hatfield, U.K.
Tianjin, China
Bangkok, Thailand
Sao Paulo SP, Brazil
Praha, Czech Republic
Guangzhou, China
Singapore
Krakowska, Poland
St. Petersburg, Russia
Beijing FA Center
Tianjin FA Center
Guangzhou FA Center
Korean FA Center
Thailand FA Center
ASEAN FA Center
North American FA Center/
North American Development Center
Brazil FA Center
European FA Center (Poland)
UK FA Center
Czech Republic FA Center
Russian FA Center
14
MEMO
1
C
N
3
C
N
1
C
N
2
L1
L2
L3
P+
C
U
Model Designation........................................1-1
Combinations of Servo Amplifier and Servo
Motor............................................................1-1
C
N
P
1
V
W
Connections with Peripheral Equipment......1-2
Specifications...............................................1-3
Standard Wiring Diagram Example..............1-4
Power Supply Connection Example.............1-8
Servo Motor Connection Example................1-9
Dimensions.................................................1-10
Servo Amplifiers
Servo Amplifiers
Servo Amplifier Model Designation
MR-JE-10A
Mitsubishi generalpurpose AC
servo amplifier
MELSERVO-JE
Series
Symbol
A
Symbol
10
20
40
70
100
200
300
Interface
General-purpose
Rated output [kW]
0.1
0.2
0.4
0.75
1
2
3
Combinations of Servo Amplifier and Servo Motor
Servo amplifier
MR-JE-10A
MR-JE-20A
MR-JE-40A
MR-JE-70A
MR-JE-100A
MR-JE-200A
MR-JE-300A
1-1
HF-KN series
HF-KN13J
HF-KN23J
HF-KN43J
HF-KN73J
-
Servo motor
HF-SN series
HF-SN52J
HF-SN102J
HF-SN152J, HF-SN202J
HF-SN302J
MR-JE-A Connections with Peripheral Equipment (Note 1)
Servo Amplifiers
Peripheral equipment is connected to MR-JE-A as described below. Connectors, cables, options, and other necessary
equipment are available so that users can set up the servo amplifier easily and start using it right away.
Molded-case circuit breaker
(MCCB)
This protects the power supply line.
Display
Magnetic contactor (MC)
This turns off the power to the servo
amplifier when an alarm is triggered.
Setting section
Parameter settings and monitoring etc. are
executed with push buttons. Push the MODE
and SET buttons for 3 s or more to switch to
the one-touch tuning mode.
Power factor improving
AC reactor (optional)
This boosts the power factor of
servo amplifier and reduces the
power supply capacity.
R
X
S
T
Y
Z
Connect a personal computer and perform
monitoring, batch parameter writing and
saving, graph display, and test operation with
MR Configurator2. Use an optional USB
cable (MR-J3USBCBL3M).
LVS/Wires
I/O signal connector (CN1)
Connect to a Mitsubishi controller or any
pulse train output controller.
FX3U FX3UC
FX3G FX3GC
Install this unit in situations
involving frequent regeneration
and large moment of inertia of
load.
Connect the servo motor encoder
using an optional cable or a
connector set.
LD75P_
LD75D_
FX 2N-10PG
Cautions
FX3U-1PG
Encoder connector (CN2)
QD70P_
QD70D_
QD75P_N
QD75D_N
Product List
Regenerative option
(optional)
Connect all signals via the junction
terminal block.
Charge lamp
The lamp lights when the main circuit
power supply is charged.
Servo motor power
cable (optional)
Options/Peripheral
Equipment
USB communication connector (CN3)
Servo Motors
Servo amplifier status,
parameter, and alarm
number are displayed.
Connect to a programmable controller I/O
port or a control cabinet of a machine.
Encoder cable (optional)
Servo motor
(The picture is as of HF-KN13J.)
Notes:1.The connection with the peripheral equipment is an example for MR-JE-100A or smaller servo amplifier. Refer to "MR-JE-_A Servo Amplifier Instruction Manual" for the
actual connections.
1-2
Servo Amplifiers
MR-JE-A (General-Purpose Interface) Specifications
Servo amplifier model MR-JERated voltage
Output
Rated current
Voltage/frequency
10A
[A]
(Note 1)
Power
supply
input
Rated current
[A]
Permissible voltage fluctuation
Permissible frequency
fluctuation
Interface power supply
Control method
Tolerable regenerative power of the
[W]
built-in regenerative resistor (Note 2, 3)
Dynamic brake
Communication function
Encoder output pulse
Analog monitor
Maximum input pulse
frequency
Positioning feedback pulse
Position
Command pulse multiplying
control
factor
mode
Positioning complete width setting
Error excessive
Torque limit
Speed control range
Analog speed command input
Speed
control
Speed fluctuation rate
mode
Torque
control
mode
Torque limit
Analog torque command input
Speed limit
Protective functions
Compliance to standards
Structure (IP rating)
Close mounting
Ambient temperature
Ambient humidity
Environment Ambience
Altitude
Vibration resistance
Mass
20A
40A
70A
3-phase 170 V AC
1.1
1.5
2.8
5.8
3-phase or 1-phase 200 V AC to 240 V AC,
50 Hz/60 Hz
0.9
1.5
2.6
3.8
3-phase or 1-phase 170 V AC to 264 V AC
100A
200A
300A
6.0
11.0
11.0
3-phase 200 V AC to 240 V AC,
50 Hz/60 Hz
5.0
10.5
14.0
3-phase 170 V AC to 264 V AC
±5% maximum
24 V DC ± 10% (required current capacity: 0.3 A)
Sine-wave PWM control/current control method
-
-
10
20
20
100
100
Built-in (Note 4)
USB: Connect a personal computer (MR Configurator2 compatible)
Compatible (A/B/Z-phase pulse)
2 channels
4 Mpps (when using differential receiver), 200 kpps (when using open-collector)
Encoder resolution: 131072 pulses/rev
Electronic gear A/B multiple, A: 1 to 16777215, B: 1 to 16777215, 1/10 < A/B < 4000
0 pulse to ±65535 pulses (command pulse unit)
±3 rotations
Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Analog speed command 1:2000, internal speed command 1:5000
0 V DC to ±10 V DC/rated speed (Speed at 10 V is changeable with [Pr. PC12].)
±0.01% maximum (load fluctuation 0% to 100%), 0% (power fluctuation: ±10%)
±0.2% maximum (ambient temperature: 25 °C ± 10 °C) only when using analog speed command
Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
0 V DC to ±8 V DC/maximum torque (input impedance: 10 kΩ to 12 kΩ)
Set by parameters or external analog input (0 V DC to ± 10 V DC/rated speed)
Overcurrent shut-off, regenerative overvoltage shut-off, overload shut-off (electronic thermal), servo
motor overheat protection, encoder error protection, regenerative error protection, undervoltage
protection, instantaneous power failure protection, overspeed protection,
error excessive protection
Refer to "Conformity with global standards and regulations" on p. 13 in this catalog.
Natural cooling, open (IP20)
Force cooling, open (IP20)
Possible (Note 5)
0 °C to 55 °C (non-freezing), storage: -20 °C to 65 °C (non-freezing)
90 %RH maximum (non-condensing), storage: 90 %RH maximum (non-condensing)
Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust
1000 m or less above sea level
5.9 m/s2 at 10 Hz to 55 Hz (directions of X, Y and Z axes)
[kg]
0.8
0.8
0.8
1.5
1.5
2.1
2.1
Notes:1.Rated output and speed of a servo motor are applicable when the servo amplifier, combined with the servo motor, is operated within the specified power supply voltage
and frequency.
2.Select the most suitable regenerative option for your system with our capacity selection software.
3.Refer to "Regenerative Option" in this catalog for the tolerable regenerative power [W] when regenerative option is used.
4.When using the built-in dynamic brake, refer to "MR-JE-_A Servo Amplifier Instruction Manual" for the permissible load to motor inertia ratio.
5.When the servo amplifiers are closely mounted, keep the ambient temperature within 0 °C to 45 °C, or use them with 75% or less of the effective load ratio.
1-3
MR-JE-A Standard Wiring Diagram Example: Position Control Operation
Servo Amplifiers
Connecting to FX3U (position servo, incremental)
Servo amplifier
MR-JE-A
Power supply connection
Power supply
The connection differs according to each servo motor.
Refer to "Servo Motor Connection Example" on p. 1-9
in this catalog.
U
L1
L2
L3
V
W
Power cable
Servo Motors
The connection differs according to the power
voltage.
Refer to "Power Supply Connection Example"
on p. 1-8 in this catalog.
Servo motor connection
Programmable controller
FX3U-_ _MT/ES (Note 3)
Programmable controller
power supply
(Note 5)
CN1
Encoder cable
DICOM
OPC
DOCOM
PP
20
12
46
10
NP
35
Y004
COM2
CR
41
X___
INP
24
X___
X000
RD
49
LG
OP
SD
3
33
Plate
N
Y000
COM1
Y010
COM3
EM2
SON
RES
LSP
LSN
DOCOM
10 m or shorter
Analog torque limit
+10 V/maximum torque
2 m or shorter
42
15
19
43
44
47
21 DICOM
48 ALM
23 ZSP
R
A
1
R
A
2
Malfunction
Zero speed detection
10 m or shorter
8
9
4
5
6
7
34
Plate
LZ
LZR
LA
LAR
LB
LBR
LG
SD
26
MO1
Encoder Z-phase pulse
(differential line driver)
Encoder A-phase pulse
(differential line driver)
Encoder B-phase pulse
(differential line driver)
Control common
10 m or shorter
(Note 1)
Analog monitor output
Output voltage: ±10 V
Maximum output current: 1 mA
30 LG
29 MO2
Product List
2 m or shorter (Note 6)
(Note 2)
Main circuit power supply
Forced stop 2
Servo-on
Reset
Forward rotation stroke end
Reverse rotation stroke end
Servo motor
CN1
LVS/Wires
(Note 7)
CN2
24 V DC
power supply
for interface
Options/Peripheral
Equipment
(Note 4)
S/S
24 V
0V
L
Output voltage: ±10 V
Maximum output current: 1 mA
Plate SD
TLA
LG
SD
27
28
Plate
2 m or shorter
Personal computer
CN3
USB cable
MR-J3USBCBL3M
Cautions
Setup software
MR Configurator2
(SW1DNC-MRC2-E)
Notes:1.This is for sink wiring. Source wiring is also possible.
2.Create a circuit to turn off EM2 when the main circuit power is turned off to prevent an unexpected restart of the servo amplifier.
3.Select the number of input/output points of the programmable controller according to your system.
4.The signal is COM0 for FX3U-16MT/ES.
5.The signal is COM4 for FX3U-16MT/ES.
6.It is recommended that the connection be 2 m or shorter because an open-collector system is used.
7.Select from the range of X000 to X007.
Be sure to read through Instruction Manual for the actual wiring and use. Use the equipment after you have a full knowledge of
the equipment, safety information and instructions.
1-4
Servo Amplifiers
MR-JE-A Standard Wiring Diagram Example: Position Control Operation
Connecting to QD75D/LD75D (position servo, incremental)
Servo amplifier
MR-JE-A
Power supply
Power supply connection
The connection differs according to the power
voltage.
Refer to "Power Supply Connection Example"
on p. 1-8 in this catalog.
Servo motor connection
The connection differs according to each servo motor.
Refer to "Servo Motor Connection Example" on p. 1-9
in this catalog.
U
L1
L2
L3
V
W
Power cable
CN2
Encoder cable
24 V DC power supply
for interface
Positioning module QD75D/LD75D
Name
CLEAR COM
CLEAR
RDY COM
READY
PULSE F+
PULSE F PULSE R+
PULSE R PG0_
PG0 COM
CN1
Pin No.
_ _14
_ _13
_ _12
_ _11
_ _15
_ _16
_ _17
_ _18
__ 9
_ _10
DICOM
DOCOM
CR
RD
PP
PG
NP
NG
LZ
LZR
LG
SD
Control common
(Note 1)
20
46 (Note 2)
41
49
10
11
35
36
8
9
3
Plate
EM2
SON
RES
LSP
LSN
DOCOM
10 m or shorter
Analog torque limit
+10 V/maximum torque
2 m or shorter
42
15
19
43
44
47
DICOM
ALM
ZSP
INP
R
A
1
R
A
2
R
A
3
Malfunction
Zero speed detection
In-position range
10 m or shorter
4
5
6
7
LA
LAR
LB
LBR
Encoder A-phase pulse
(differential line driver)
Encoder B-phase pulse
(differential line driver)
Control common
Control common
Encoder Z-phase pulse
(Open collector)
34 LG
33 OP
Plate SD
10 m or shorter
(Note 3)
Main circuit power supply
Forced stop 2
Servo-on
Reset
Forward rotation stroke end
Reverse rotation stroke end
21
48
23
24
Servo motor
CN1
2 m or shorter
(Note 2)
10 m or shorter
26
MO1
Analog monitor output
Output voltage: ±10 V
Maximum output current: 1 mA
30 LG
29 MO2
Output voltage: ±10 V
Maximum output current: 1 mA
Plate SD
TLA
LG
SD
27
28
Plate
2 m or shorter
Setup software
MR Configurator2
(SW1DNC-MRC2-E)
USB cable
MR-J3USBCBL3M
CN3
Personal computer
Notes:1.This connection is not necessary for QD75D/LD75D positioning module. Note that the connection between LG and control common terminal is recommended for some
positioning modules to improve noise immunity.
2.This is for sink wiring. Source wiring is also possible.
3.Create a circuit to turn off EM2 when the main circuit power is turned off to prevent an unexpected restart of the servo amplifier.
Be sure to read through Instruction Manual for the actual wiring and use. Use the equipment after you have a full knowledge of
the equipment, safety information and instructions.
1-5
MR-JE-A Standard Wiring Diagram Example: Speed Control Operation
Power supply
Power supply connection
Servo motor connection
The connection differs according to each servo motor.
Refer to "Servo Motor Connection Example" on p. 1-9
in this catalog.
U
L1
L2
L3
V
W
Power cable
Servo Motors
The connection differs according to the power
voltage.
Refer to "Power Supply Connection Example"
on p. 1-8 in this catalog.
Servo Amplifiers
Servo amplifier
MR-JE-A
CN2
Encoder cable
24 V DC power supply
for interface
(Note 2)
Main circuit power supply
Forced stop 2
Servo-on
Forward rotation start
Reverse rotation start
Forward rotation stroke end
Reverse rotation stroke end
20
46
EM2
SON
ST1
ST2
LSP
LSN
DOCOM
42
15
19
41
43
44
47
TLA
LG
27
28
10 m or shorter
Analog torque limit
+10 V/maximum torque
VC
SD
DICOM
ALM
ZSP
RD
SA
R
A
2
R
A
3
R
A
4
Malfunction
Zero speed detection
Ready
Speed reached
10 m or shorter
8
9
4
5
6
7
LZ
LZR
LA
LAR
LB
LBR
Encoder Z-phase pulse
(differential line driver)
Encoder A-phase pulse
(differential line driver)
Encoder B-phase pulse
(differential line driver)
Control common
Control common
Encoder Z-phase pulse
(Open collector)
34 LG
33 OP
Plate SD
2
Plate
2 m or shorter
R
A
1
2 m or shorter
10 m or shorter
26 MO1
Product List
Analog speed command
±10 V/rated speed
(in this wiring diagram,
+10 V/rated speed)
(Note 1)
21
48
23
49
24
LVS/Wires
DICOM
DOCOM
Servo motor
CN1
Options/Peripheral
Equipment
CN1
Analog monitor output
Output voltage: ±10 V
Maximum output current: 1 mA
30 LG
29 MO2
Output voltage: ±10 V
Maximum output current: 1 mA
Plate SD
Personal computer
CN3
USB cable
MR-J3USBCBL3M
Cautions
Setup software
MR Configurator2
(SW1DNC-MRC2-E)
2 m or shorter
Notes:1.This is for sink wiring. Source wiring is also possible.
2.Create a circuit to turn off EM2 when the main circuit power is turned off to prevent an unexpected restart of the servo amplifier.
Be sure to read through Instruction Manual for the actual wiring and use. Use the equipment after you have a full knowledge of
the equipment, safety information and instructions.
1-6
Servo Amplifiers
MR-JE-A Standard Wiring Diagram Example: Torque Control Operation
Servo amplifier
MR-JE-A
Power supply
Power supply connection
The connection differs according to the power
voltage.
Refer to "Power Supply Connection Example"
on p. 1-8 in this catalog.
Servo motor connection
The connection differs according to each servo motor.
Refer to "Servo Motor Connection Example" on p. 1-9
in this catalog.
U
L1
L2
L3
V
W
Power cable
CN2
Encoder cable
CN1
24 V DC power supply
for interface
(Note 2)
Main circuit power supply
Forced stop 2
Servo-on
Forward rotation selection
Reverse rotation selection
DICOM
DOCOM
20
46
EM2
SON
RS1
RS2
DOCOM
42
15
41
19
TC
LG
27
28
47
10 m or shorter
Analog torque command
±8 V/maximum torque
(in this wiring diagram,
+8 V/max. torque)
Analog speed command
±10 V/rated speed
(in this wiring diagram,
+10 V/rated speed)
VLA
SD
2
Plate
2 m or shorter
(Note 1)
21
48
23
49
Servo motor
CN1
DICOM
ALM
ZSP
RD
R
A
1
R
A
2
R
A
3
Malfunction
Zero speed detection
Ready
10 m or shorter
8
9
4
5
6
7
LZ
LZR
LA
LAR
LB
LBR
Encoder Z-phase pulse
(differential line driver)
Encoder A-phase pulse
(differential line driver)
Encoder B-phase pulse
(differential line driver)
Control common
Control common
Encoder Z-phase pulse
(Open collector)
34 LG
33 OP
Plate SD
2 m or shorter
10 m or shorter
26 MO1
Analog monitor output
Output voltage: ±10 V
Maximum output current: 1 mA
30 LG
29 MO2
Output voltage: ±10 V
Maximum output current: 1 mA
Plate SD
2 m or shorter
Setup software
MR Configurator2
(SW1DNC-MRC2-E)
USB cable
MR-J3USBCBL3M
CN3
Personal computer
Notes:1.This is for sink wiring. Source wiring is also possible.
2.Create a circuit to turn off EM2 when the main circuit power is turned off to prevent an unexpected restart of the servo amplifier.
Be sure to read through Instruction Manual for the actual wiring and use. Use the equipment after you have a full knowledge of
the equipment, safety information and instructions.
1-7
Power Supply Connection Example
Off
Emergency
stop switch
SK
MC
L1
L2
L3
CNP1
U
V
W
P+
Regenerative
option
(Note 2)
C
Malfunction
RA1 MC
Servo amplifier
MR-JE-A
SK
MC
Power supply
3-phase 200 V AC
to 240 V AC
Regenerative
option
(Note 2)
L1
L2
L3
CNP1
U
V
W
P+
C
Built-in
regenerative
resistor
The servo amplifier may be
damaged if the regenerative option
is incorrectly connected.
The servo amplifier may be
damaged if the regenerative option
is incorrectly connected.
LVS/Wires
●●For 3-phase 200 V AC, 2 kW and 3 kW
Power supply
3-phase 200 V AC
to 240 V AC
MCCB
Malfunction
RA1 MC
Servo amplifier
MR-JE-A
SK
MC
L1
L2
L3
N-
CNP1
C
D
P+
Built-in
regenerative
resistor
Cautions
Regenerative
option
(Note 3)
Product List
Emergency
stop switch
On
MC
Off
Options/Peripheral
Equipment
Built-in
regenerative
resistor
MCCB
On
Servo Motors
MCCB
Servo amplifier
MR-JE-A
MC
Malfunction
RA1
MC
Emergency
stop switch
Power supply
1-phase 200 V AC
to 240 V AC
(Note 1)
On
MC
Off
●●For 3-phase 200 V AC, 1 kW or smaller
Servo Amplifiers
●●For 1-phase 200 V AC
The servo amplifier may be
damaged if the regenerative option
is incorrectly connected.
Notes:1.For 1-phase 200 V AC to 240 V AC, connect the power supply to L1 and L3 terminals. Do not connect anything to L2. The connections are different from MR-E Super
series servo amplifiers. Be careful not to make a connection error when replacing MR-E Super with MR-JE.
2.Disconnect the wires for the built-in regenerative resistor (P+ and C) and remove the resistor when connecting the regenerative option externally.
3.Disconnect a short-circuit bar between P+ and D when connecting the regenerative option externally.
Be sure to read through Instruction Manual for the actual wiring and use. Use the equipment after you have a full knowledge of
the equipment, safety information and instructions.
1-8
Servo Amplifiers
Servo Motor Connection Example
●●For HF-KN series
Servo amplifier
MR-JE-A
U
(Note 4)
U
V
V
W
W
(Note 3)
24 V DC for the
(Note 3) electromagnetic brake
(Note 5)
Contact must be open by
an external emergency
stop switch.
CN2
P5
LG
MR
MRR
BAT
SD
4
B2
1
2
B
Electromagnetic
Contact must be open when brake
the ALM (Malfunction) or the
(Note 2)
MBR (Electromagnetic brake
interlock) turns off.
(Note 1)
P5
LG
MR
MRR
BAT
SD
(Note 6)
Encoder
1
2
3
4
9
Plate
U
M
3
1
B1
RA
Servo motor
2
●●For HF-SN series
Servo amplifier
MR-JE-A
U
(Note 4)
U
V
V
W
W
(Note 3)
24 V DC for the
(Note 3) electromagnetic brake
(Note 5)
Contact must be open by
an external emergency
stop switch.
CN2
P5
LG
MR
MRR
BAT
SD
(Note 1)
(Note 6)
C
B2
1
2
B
Electromagnetic
Contact must be open when brake
the ALM (Malfunction) or the
(Note 2)
MBR (Electromagnetic brake
interlock) turns off.
P5
LG
MR
MRR
BAT
SD
Encoder
1
2
3
4
9
Plate
U
M
B
D
B1
RA
Servo motor
A
Notes:1.The signals shown is applicable when using a two-wire type encoder cable. Four-wire type is also compatible.
2.This is for the servo motor with electromagnetic brake. The electromagnetic brake terminals (B1, B2) do not have polarity.
3.For MR-JE-100A or smaller servo amplifier, connect the grounding terminal of the servo motor to
of CNP1, and connect the protective earth (PE) terminal (
) located
on the lower front of the servo amplifier to the cabinet protective earth (PE).
For MR-JE-200A or larger servo amplifier, connect the grounding terminal of the servo motor to the protective earth (PE) terminal (
) located on the lower front of the
servo amplifier, and connect the other protective earth (PE) terminal (
) to the cabinet protective earth (PE).
4.The connector varies depending on the servo amplifier capacities. Refer to "MR-JE-A Dimensions" in this catalog.
5.Do not use the 24 V DC interface power supply for the electromagnetic brake. Provide a dedicated power supply to the electromagnetic brake.
6.Encoder cable is available as an option. Refer to "HF-KN HF-SN Servo Motor Instruction Manual" when fabricating the cables.
Be sure to read through Instruction Manual for the actual wiring and use. Use the equipment after you have a full knowledge of
the equipment, safety information and instructions.
1-9
MR-JE-A Dimensions
Servo Amplifiers
●●MR-JE-10A (Note 1)
●●MR-JE-20A (Note 1)
●●MR-JE-40A (Note 1)
50
6
Approx. 80
135
j6 mounting hole
6
CNP1
L1
CN3
L2
C
N
3
L3
P+
C
168
156
CN2
U
C
N
2
L1
L2
L3
P+
C
C
N
P
1
U
V
Servo Motors
CN1
C
N
1
V
CNP1
W
W
6
PE
PE
6
Screw size: M4
Mounting screw size: M5
6
[Unit: mm]
2.9
●●MR-JE-70A (Note 1)
●●MR-JE-100A (Note 1)
Approx. 80
70
j6 mounting hole
Options/Peripheral
Equipment
Built-in regenerative resistor (lead wires)
is mounted in MR-JE-40A only.
185
22
LVS/Wires
6
CNP1
L1
CN3
L2
C
N
3
L3
CN1
C
N
1
P+
U
C
N
P
1
CNP1
V
W
W
Product List
L1
L2
L3
P+
C
U
V
C
168
156
CN2
C
N
2
6
PE
6
22
PE
Screw size: M4
42
Mounting screw size: M5
3.3
[Unit: mm]
●●MR-JE-300A (Note 2)
j6 mounting hole
Approx. 80
195
Exhaust
CNP1
6
45
90
85
Cautions
●●MR-JE-200A (Note 2)
CN3
CNP1
L1
C
N
3
L1
L2
L2
L3
L3
N-
CN1
N-
168
156
D
P+
161
C
C
C
N
1
CNP2
U
D
P+
CN2
V
W
C
N
2
6
CNP2
U
Intake
Cooling fan
PE
V
6
PE
W
6
78
Screw size: M4
Mounting screw size: M5
6
[Unit: mm]
Notes:1.CNP1 connector (insertion type) is supplied with the servo amplifier.
2.CNP1 and CNP2 connectors (insertion type) are supplied with the servo amplifier.
1-10
MEMO
2
Model Designation........................................2-1
Combinations of Servo Motor and Servo
Amplifier.......................................................2-1
Specifications
HF-KN series................................................2-2
HF-SN series................................................2-4
Dimensions
HF-KN series................................................2-7
HF-SN series..............................................2-10
Sizing Example...........................................2-11
Servo Motors
Servo Motors
Model Designation
HF-KN13BJ
Symbol
None
K
D
Symbol
J
None
Shaft end
Standard (Straight shaft)
Key shaft (with/without key) (Note 4)
D-cut shaft (Note 4)
Oil seal
Installed (Note 5)
None (Note 6)
Symbol Electromagnetic brake
None
None
B
Installed (Note 1)
Symbol
2
3
Rated speed [r/min]
2000 (Note 2)
3000 (Note 3)
Symbol
1 to 7
10 to 30
Rated output [kW]
0.1 to 0.75
1.0 to 3.0
Symbol
HF-KN
HF-SN
Inertia/capacity
Low inertia, small capacity
Medium inertia, medium capacity
Notes:1.Refer to electromagnetic brake specifications of each servo motor series in this catalog for the available models and detailed specifications.
2.2000 r/min is for HF-SN series only.
3.3000 r/min is for HF-KN series only.
4.Refer to special shaft end specifications of each servo motor series in this catalog for the available models and detailed specifications.
5.An oil seal is attached as a standard for all servo motors.
6.Available in HF-KN13 to HF-KN43.
Combinations of Servo Motor and Servo Amplifier
HF-KN
series
HF-SN
series
2-1
Servo motor
HF-KN13(B)J
HF-KN23(B)J
HF-KN43(B)J
HF-KN73(B)J
HF-SN52(B)J
HF-SN102(B)J
HF-SN152(B)J
HF-SN202(B)J
HF-SN302(B)J
Servo amplifier
MR-JE-10A
MR-JE-20A
MR-JE-40A
MR-JE-70A
MR-JE-70A
MR-JE-100A
MR-JE-200A
MR-JE-200A
MR-JE-300A
HF-KN Series (Low Inertia, Small Capacity) Specifications
Servo Amplifiers
13(B)J
23(B)J
43(B)J
73(B)J
Refer to "Combinations of Servo Motor and Servo Amplifier" on p. 2-1 in this catalog.
0.3
0.5
0.9
1.3
100
200
400
750
0.32
0.64
1.3
2.4
0.95
1.9
3.8
7.2
3000
4500
5175
11.5
16.9
38.6
39.9
13.1
32.5
35.0
0.8
2.4
(Note 4)
0.088
1.3
3.9
(Note 4)
0.24
2.7
8.1
249
0.42
4.8
14
140
1.43
0.090
0.31
0.50
1.63
Options/Peripheral
Equipment
11.3
Servo Motors
15 times or less
Incremental 17-bit encoder (resolution: 131072 pulses/rev)
Installed. Without oil seal is also available.
Installed
130 (B)
Totally enclosed, natural cooling (IP rating: IP65) (Note 2)
0 °C to 40 °C (non-freezing), storage: -15 °C to 70 °C (non-freezing)
80 %RH maximum (non-condensing), storage: 90 %RH maximum (non-condensing)
Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust
1000 m or less above sea level
X: 49 m/s2 Y: 49 m/s2
V10 *7
Refer to "Conformity with global standards and regulations" on p. 13 in this catalog.
25
30
30
40
88
245
245
392
59
98
98
147
0.6
1.2
1.6
3.1
1.6
2.0
Product List
0.8
LVS/Wires
Servo motor model
HF-KN
Compatible servo amplifier model
Power supply capacity *1
[kVA]
Rated output
[W]
Continuous
running duty
Rated torque (Note 3)
[N•m]
Maximum torque
[N•m]
Rated speed
[r/min]
Maximum speed
[r/min]
Permissible instantaneous speed
[r/min]
[kW/s]
Power rate at Standard
continuous
With electromagnetic
[kW/s]
rated torque
brake
Rated current
[A]
Maximum current
[A]
Regenerative braking frequency *2, *3 [times/min]
Standard
[× 10-4 kg•m2]
Moment of
With electromagnetic
inertia J
[× 10-4 kg•m2]
brake
Recommended load to motor inertia ratio (Note 1)
Speed/position detector
Oil seal
Insulation class
Structure
Ambient temperature
Ambient humidity
Environment *4 Ambience
Altitude
Vibration resistance *5
Vibration rank
Compliance to standards
L
[mm]
Permissible
load for the
Radial
[N]
shaft *6
Thrust
[N]
Standard
[kg]
Mass
With electromagnetic
[kg]
brake
4.1
Cautions
Notes:1.Contact your local sales office if the load to motor inertia ratio exceeds the value in the table.
2.The shaft-through portion is excluded. Refer to the asterisk 8 of "Annotations for Servo Motor Specifications" on p. 2-6 in this catalog for the shaft-through portion.
3.When unbalanced torque is generated, such as in a vertical lift machine, it is recommended that the unbalanced torque of the machine be kept under 70% of the servo
motor rated torque.
4.When the servo motor decelerates to a stop from the rated speed, the regenerative frequency will not be limited if the effective torque is within the rated torque range.
Note that the recommended load to motor inertia ratio is 15 times or less.
Refer to "Annotations for Servo Motor Specifications" on p. 2-6 in this catalog for the asterisks 1 to 7.
2-2
Servo Motors
HF-KN Series Electromagnetic Brake Specifications (Note 1)
Servo motor model
HF-KN
Type
Rated voltage
Power consumption
[W] at 20 °C
Electromagnetic brake
[N•m]
static friction torque
[J]
Permissible braking Per braking
work
Per hour
[J]
13BJ
56
220
220
640
Electromagnetic
brake life (Note 2)
20000
20000
20000
20000
5.6
22
22
64
6.3
0.32
1.3
5.6
Number of brakings
[Times]
Work per braking[J]
73BJ
10
1.3
22
2.4
22
64
Notes:1.The electromagnetic brake is for holding. It should not be used for deceleration applications.
2.Brake gap is not adjustable. Electromagnetic brake life is defined as the time period until the readjustment is needed.
HF-KN Series Torque Characteristics (Note 3, 4)
0
Continuous0.25
running range
1000
2000
0
Continuous
running range
3000 1000
4000 4500
2000
Speed [r/min]
3000
Speed [r/min]
0.5
4000 4500
0
Continuous 0.5
running range
1000
HF-KN43(B)J (Note 1, 2)
8.0
8.0
6.0
Short-duration
6.0
running range
1.0
4000 4500
0
2.0
Continuous 1.0
running range
1000
2000
0
Continuous
running range
3000 1000
4000 4500
2000
Speed [r/min]
3000
Speed [r/min]
Torque [N•m]
4.0
2.0
3000 1000
4000 4500
2000
3000
Speed [r/min]
1.0
4000 4500
0
2.0
Continuous 1.0
running range
1000
2000
0
Continuous
running range
3000 1000
4000 4500
2000
Speed [r/min]
3000
Speed [r/min]
6.0
4.0
2.0
4000 4500
Short-duration
running range
4.0
Continuous 2.0
running range
0
1000
2000
0
Continuous
running range
3000 1000
4000 4500
2000
Speed [r/min]
4.0
2.0
4000 4500
0
4.0
Continuous 2.0
running range
1000
Short-duration
running range
2000
0
Continuous
running range
3000 1000
4000 4500
2000
Speed [r/min]
3000
Speed [r/min]
4000 4500
Notes: 1.
:For 3-phase 200 V AC.
2.
:For 1-phase 230 V AC.
3. Torque drops when the power supply
voltage is below the specified value.
4. The value is for reference.
HF-KN Series Special Shaft End Specifications
Motors with the following specifications are also available.
D-cut shaft (Note 1): 100 W
25
21.5
20.5
1
φ8h6
[Unit: mm]
Key shaft (with key) (Note 1, 2): 200 W, 400 W, and 750 W
HF-KN
Q
Variable dimensions
T
S
R
Q
W
QK
23(B)JK,
43(B)JK
5
14h6
30
27
5
20
73(B)JK
6
19h6
40
37
6
25
QL
U
Y
3
3
M4 screw
Depth: 15
5
3.5
M5 screw
Depth: 20
QK
A
QL
U
φS
Model
R
W
3000
eed [r/min]
0
2.0
8.0
Short-duration
6.0
running range
HF-KN73(B)J (Note 1, 2)
Torque [N•m]
Torque [N•m]
s
nge
2000
Continuous
running range
Speed [r/min]
Short-duration
Short-duration
3.0 running range
3.0 running range
Torque [N•m]
4.0
1.0
8.0
Torque [N•m]
0.25
1.0
Short-duration
Short-duration
3.0 running range
3.0 running range
Torque [N•m]
0.5
Short-duration
Short-duration
1.5 running range1.5 running range
4.0
Torque [N•m]
0.5
Short-duration
running range
4.0
Torque [N•m]
0.75
Short-duration
running range
0.75
2.0
Torque [N•m]
1.0
HF-KN23(B)J (Note 1, 2)
2.0
Torque [N•m]
1.0
Torque [N•m]
Torque [N•m]
HF-KN13(B)J (Note 1, 2)
ion
ge
500
000
23BJ
43BJ
Spring actuated type safety brake
24 V DC -100 %
7.9
7.9
A
T
Y
A-A
[Unit: mm]
Notes:1.The servo motors with special shaft end are not suitable for frequent start/stop applications.
2.2 round end key is attached.
2-3
3000
Speed [r/min]
HF-SN Series (Medium Inertia, Medium Capacity) Specifications
Servo Amplifiers
52(B)J
102(B)J
152(B)J
202(B)J
302(B)J
Refer to "Combinations of Servo Motor and Servo Amplifier" on p. 2-1 in this catalog.
1.0
1.7
2.5
3.5
4.8
0.5
1.0
1.5
2.0
3.0
2.39
4.77
7.16
9.55
14.3
7.16
14.3
21.5
28.6
42.9
2000
3000
2500
3450
2875
9.34
19.2
28.8
23.8
35.1
16.3
25.6
19.0
30.1
2.9
8.7
120
6.1
6.0
18
62
11.9
8.6
26
152
17.8
9.0
27
71
38.3
11
33
28
58.5
8.3
14.0
20.0
47.9
68.1
Options/Peripheral
Equipment
6.87
Servo Motors
15 times or less
Incremental 17-bit encoder (resolution: 131072 pulses/rev)
Installed
155 (F)
Totally enclosed, natural cooling (IP rating: IP67) (Note 2)
0 °C to 40 °C (non-freezing), storage: -15 °C to 70 °C (non-freezing)
80 %RH maximum (non-condensing), storage: 90 %RH maximum (non-condensing)
Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust
1000 m or less above sea level
X: 24.5 m/s2 Y: 24.5 m/s2
X: 24.5 m/s2 Y: 49 m/s2
V10 *7
Refer to "Conformity with global standards and regulations" on p. 13 in this catalog.
55
55
55
79
79
980
980
980
2058
2058
490
490
490
980
980
4.8
6.5
8.3
12
15
8.5
10.3
18
Product List
6.7
LVS/Wires
Servo motor model
HF-SN
Compatible servo amplifier model
Power supply capacity *1
[kVA]
Rated output
[kW]
Continuous
running duty
Rated torque (Note 3)
[N•m]
Maximum torque
[N•m]
Rated speed
[r/min]
Maximum speed
[r/min]
Permissible instantaneous speed
[r/min]
[kW/s]
Power rate at Standard
continuous
With electromagnetic
[kW/s]
rated torque
brake
Rated current
[A]
Maximum current
[A]
Regenerative braking frequency *2, *3 [times/min]
Standard
[× 10-4 kg•m2]
Moment of
With electromagnetic
inertia J
[× 10-4 kg•m2]
brake
Recommended load to motor inertia ratio (Note 1)
Speed/position detector
Oil seal
Insulation class
Structure
Ambient temperature
Ambient humidity
Environment *4 Ambience
Altitude
Vibration resistance *5
Vibration rank
Compliance to standards
L
[mm]
Permissible
load for the
Radial
[N]
shaft *6
Thrust
[N]
Standard
[kg]
Mass
With electromagnetic
[kg]
brake
21
Refer to "Annotations for Servo Motor Specifications" on p. 2-6 in this catalog for the asterisks 1 to 7.
2-4
Cautions
Notes:1.Contact your local sales office if the load to motor inertia ratio exceeds the value in the table.
2.The shaft-through portion is excluded. Refer to the asterisk 8 of "Annotations for Servo Motor Specifications" on p. 2-6 in this catalog for the shaft-through portion.
3.When unbalanced torque is generated, such as in a vertical lift machine, it is recommended that the unbalanced torque of the machine be kept under 70% of the servo
motor rated torque.
Servo Motors
HF-SN Series Electromagnetic Brake Specifications (Note 1)
Servo motor model
HF-SN
Type
Rated voltage
Power consumption
[W] at 20 °C
Electromagnetic brake
[N•m]
static friction torque
[J]
Permissible braking Per braking
work
Per hour
[J]
52BJ
102BJ
20
20
8.5
8.5
4000
4000
4000
45000
45000
Electromagnetic
brake life (Note 2)
20000
20000
20000
20000
20000
200
200
200
1000
1000
400
Number of brakings
[Times]
Work per braking [J]
152BJ
202BJ
Spring actuated type safety brake
24 V DC -100 %
20
34
8.5
400
302BJ
34
44
400
44
4500
4500
Notes:1.The electromagnetic brake is for holding. It should not be used for deceleration applications.
2.Brake gap is not adjustable. Electromagnetic brake life is defined as the time period until the readjustment is needed.
HF-SN Series Torque Characteristics (Note 3, 4)
HF-SN52(B)J (Note 1, 2)
0
15
15
Continuous
running range
1000
0
2000
Continuous
running range
30001000
0
2000
Speed [r/min]
24
30001000
0
2000
Speed [r/min]
24
30001000
0
2000
Speed [r/min]
30
24
30001000
0
2000
Speed [r/min]
30001000
30
0
2000
Speed [r/min]
30001000
8
0
2000
Speed [r/min]
Continuous
running range
30001000
8
0
2000
Speed [r/min]
10
Continuous
running range
30001000
0
2000
Speed [r/min]
10
Continuous
running range
30001000
0
2000
Speed [r/min]
HF-SN302(B)J (Note 1)
45
30
Torque [N•m]
Short-duration
20 running range
10
Continuous
running range
1000
2000
Speed [r/min]
30
Short-duration
running range
Notes: 1.
:For 3-phase 200 V AC.
2.
:For 1-phase 230 V AC.
3. Torque drops when the power supply
voltage is below the specified value.
4. The value is for reference.
15
0
3000
Continuous
running range
1000
2000 2500
Speed [r/min]
HF-SN Series Special Shaft End Specifications
Motors with the following specifications are also available.
Key shaft (without key) (Note 1, 2)
202(B)JK,
302(B)JK
Q
S
R
Q
W
QK QL
24h6
55
50
8 -0.036
0
36
5
4 0
79
75
10 -0.036
0
55
5
5 0
+0.010
35 0
U
r
+0.2
4
+0.2
5
Y
QK
M8 screw
Depth: 20
Notes:1.The servo motors with special shaft end are not suitable for frequent start/stop applications.
2.A key is not supplied with the servo motor. The key shall be installed by the user.
A
QL
U
φS
52(B)JK,
102(B)JK,
152(B)JK
R
Variable dimensions
W
Model
HF-SN
A
r
A-A
Y
[Unit: mm]
2-5
30
Torque [N•m]
Continuous
running range
Torque [N•m]
8
Torque [N•m]
Continuous
running range
Torque [N•m]
5
Continuous
running range
Torque [N•m]
5
Continuous
running range
Torque [N•m]
5
Continuous
running range
HF-SN202(B)J (Note 1)
Torque [N•m]
15
Torque [N•m]
3
Torque [N•m]
3
Speed [r/min]
0
HF-SN152(B)J (Note 1)
Short-duration
Short-duration
Short-duration Short-duration
Short-duration
Short-duration Short-duration
Short-duration
Shor
Short-duration 6 Short-duration 6 Short-duration10 running range10 running range10 running range16 running range16 running range16 running range20 running range20 running range20 runn
running range
running range
running range
Torque [N•m]
3
9
Torque [N•m]
6
9
Torque [N•m]
Torque [N•m]
9
HF-SN102(B)J (Note 1)
10
Continuous
running range
30001000
0
2000
Speed [r/min]
Con
runn
30001
Sp
Annotations for Servo Motor Specifications
X
Servo Motors
Servo motor
Servo Amplifiers
*1. The power supply capacity varies depending on the power supply impedance.
*2. The regenerative braking frequency shows the permissible frequency when the servo motor, without a load and a regenerative option, decelerates from the rated speed to
a stop. When a load is connected; however, the value will be the table value/(m+1), where m = Moment of inertia of load/Moment of inertia of servo motor.
When the operating speed exceeds the rated speed, the regenerative braking frequency is inversely proportional to the square of (operating speed/rated speed). Take
measures to keep the regenerative power [W] during operation below the tolerable regenerative power [W]. Use caution, especially when the operating speed changes
frequently or when the regeneration is constant (as with vertical feeds). Select the most suitable regenerative option for your system with our capacity selection software.
Refer to "Regenerative Option" in this catalog for the tolerable regenerative power [W] when regenerative option is used.
*3. For 400 W or smaller servo amplifier, the regenerative braking frequency may change affected by the power supply voltage due to the large ratio of the energy charged
into the electrolytic capacitor in the servo amplifier.
*4. In the environment where the servo motor is exposed to oil mist, oil and/or water, a standard specification servo motor may not be usable. Contact your local sales office
for more details.
*5. The vibration direction is shown in the diagram below. The numerical value indicates the maximum value of the component (commonly the bracket in the opposite
direction of the servo motor shaft).
Fretting more likely occurs on the bearing when the servo motor stops. Thus, maintain vibration level at approximately one-half of the allowable value.
Y
L
Radial load
L: Distance between the flange mounting surface and the center of load
Options/Peripheral
Equipment
*6. Refer to the diagram below for the permissible load for the shaft. Do not apply a load exceeding the value specified in the table on the shaft. The values in the table are
applicable when each load is applied singly.
Thrust load
LVS/Wires
*7. V10 indicates that the amplitude of the servo motor itself is 10 µm or less. The following shows mounting posture and measuring position of the servo motor during the
measurement:
Servo motor
Top
Measuring position
Bottom
Product List
*8. Refer to the diagram below for shaft-through portion.
Shaft-through portion
Cautions
2-6
Servo Motors
HF-KN Series Dimensions (Note 1, 5)
●●HF-KN13(B)J
2-ø4.5 mounting hole
Use hexagonal cap head bolts.
ø30h7
9.9
19.2
6
Power
connector
13.9
27.5
48.4
6.4
Electromagnetic brake connector (Note 3)
When the cables are led out in opposite direction of load side
Encoder
connector
13°
1
9°
7°
18.4
(Note 3)
ø4
37.1
ø8h6
20.7
36
21
38.8 (Note 3)
27.4
10.1
11.7 11.7
21.5
58.8 (Note 3)
Electromagnetic brake connector (Note 2)
Pin No. Signal name
1
1
B1
2
2
B2
2
Encoder
connector
4.9
3
4
Pin No. Signal name
1
(PE)
2
U
3
V
4
W
1
Oil seal
SC10207
13.7
40
4
45°
3
25
2.5
21.5
5
2
95 (131.9) (Note 4)
20.7
1
2
1
20.5
Power connector
2
11.7 11.7
18.4
(Note 3)
58.8
(Note 3)
21.5
19.2
9.9
Power
connector
Electromagnetic brake
connector (Note 3)
(Note 3)
[Unit: mm]
●●HF-KN13(B)
20.7
ø30h7
6
ø8h6
37.1
21
36
38.8 (Note 3)
Electromagnetic brake connector (Note 2)
Pin No. Signal name
1
1
B1
2
2
B2
ø4
2
10.1
11.7 11.7
21.5
58.8 (Note 3)
9.9
19.2
18.4
(Note 3)
Power connector
13.9
27.5
40.4
6.4
Electromagnetic brake connector (Note 3)
When the cables are led out in opposite direction of load side
2
13°
1
9°
7°
4.9
Pin No. Signal name
1
(PE)
2
U
3
V
4
W
1
Encoder
connector
13.7
27.4
4
3
4
40
45°
3
25
2.5
21.5
5
2
87 (123.9)
20.7
1
2
2-ø4.5 mounting hole
Use hexagonal cap head bolts.
1
20.5
Power connector
(Note 3)
Encoder
connector
11.7 11.7
21.5
58.8
(Note 3)
18.4
(Note 3)
19.2
9.9
Power
connector
Electromagnetic brake
connector (Note 3)
[Unit: mm]
Notes:1.For dimensions without tolerance, general tolerance applies.
2.The electromagnetic brake terminals (B1, B2) do not have polarity.
3.Only for the models with electromagnetic brake.
4.Dimensions in brackets are for the models with electromagnetic brake.
5.Use a friction coupling to fasten a load.
2-7
HF-KN Series Dimensions (Note 1, 5)
Power connector
ø14h6
Electromagnetic brake connector (Note 2)
Pin No. Signal name
1
1
B1
2
2
B2
ø7
0
ø50h7
47.1
46
10
L
KL
HF-KN23(B)J
98.4
(127)
14
9.5
11.7
19.2
21.5
60 (Note 3)
Power
connector
13.9
5.9
27.8
48
KL
Electromagnetic brake connector (Note 3)
HF-KN43(B)J
120.4
(149)
70
When the cables are led out in opposite direction of load side
Power
connector
7°
13.5°
9°
Options/Peripheral
Equipment
28.4
10.1
Encoder
connector
Variable
dimensions (Note 4)
Encoder
connector
14
18.3
(Note 3)
11.7
60
(Note 3)
21.5
(Note 3)
9.5
Electromagnetic brake
connector (Note 3)
●●HF-KN23(B), HF-KN43(B)
Power connector
Electromagnetic brake connector (Note 2)
1
Pin No. Signal name
1
B1
2
2
B2
ø7
10.1
28.4
9.5
11.8 11.7
Power
connector
13.9
KL
5.9
27.8
Electromagnetic brake connector (Note 3)
When the cables are led out in opposite direction of load side
Encoder
connector
(Note 3)
Variable
dimensions (Note 4)
L
KL
HF-KN23(B)
88.2
(116.8)
40
HF-KN43(B)
110.2
(138.8)
62
Power
connector
7°
13.5°
9°
21.5
57.8 (Note 3)
19.2
47.1
ø14h6
47.1 (Note 3)
46
10
Model
11.8 11.7
21.5
18.3
57.8
(Note 3)
(Note 3)
9.5
Electromagnetic brake
connector (Note 3)
[Unit: mm]
Notes:1.For dimensions without tolerance, general tolerance applies.
2.The electromagnetic brake terminals (B1, B2) do not have polarity.
3.Only for the models with electromagnetic brake.
4.Dimensions in brackets are for the models with electromagnetic brake.
5.Use a friction coupling to fasten a load.
2-8
Cautions
13.7
2
ø50h7
1
0
Encoder
connector
Pin No. Signal name
1
(PE)
2
U
3
V
4
W
Product List
°
4
3
4
60
45
3
3
2
7
1
2
1
4-ø5.8 mounting hole
Use hexagonal cap
head bolts.
30
LVS/Wires
[Unit: mm]
L
Servo Motors
2
Model
Oil seal
SC15377
13.7
Pin No. Signal name
1
(PE)
2
U
3
V
4
W
1
47.1 (Note 3)
4
°
45
3
3
4
60
3
2
7
1
2
1
30
L
4-ø5.8 mounting hole
Use hexagonal cap
head bolts.
Servo Amplifiers
●●HF-KN23(B)J, HF-KN43(B)J
Servo Motors
HF-KN Series Dimensions (Note 1, 5)
●●HF-KN73(B)J
Power connector
133.9 (166.5) (Note 4)
8
80
°
45
3
36
1
2
3
4
1 2 3 4
4-ø6.6 mounting hole
Use hexagonal cap
40 head bolts.
Pin No. Signal name
1
(PE)
2
U
3
V
4
W
Electromagnetic brake connector (Note 2)
1
Pin No. Signal name
1
B1
2
2
B2
ø9
1
0
ø70h7
ø19h6
2
13.7
27.4
11.5
Encoder
connector
9.9
14
21.4
9.5
19.2
11.7
57.1
56
Oil seal
SC24387
Power
connector
14
67.7 (Note 3)
12
27.8
79.6
Electromagnetic brake connector (Note 3)
7°
7°
7°
When the cables are led out in opposite direction of load side
Encoder
connector
Power connector
14 11.7
21.4
18.4
(Note 3)
67.7 (Note 3)
9.5
Electromagnetic brake
connector (Note 3)
(Note 3)
[Unit: mm]
Notes:1.For dimensions without tolerance, general tolerance applies.
2.The electromagnetic brake terminals (B1, B2) do not have polarity.
3.Only for the models with electromagnetic brake.
4.Dimensions in brackets are for the models with electromagnetic brake.
5.Use a friction coupling to fasten a load.
2-9
HF-SN Series Dimensions (Note 1, 5)
55
L
34.5 (45)
(Note 4)
12
45°
ø1
65
(Note 3)
Oil seal
(Note 3)
(Note 3)
13
(Note 3)
45
ø1
96
(Note 3)
(Note 3)
Electromagnetic brake connector
CM10-R2P (Note 3)
9 (Note 3)
18
24.5
KL
Power connector
MS3102A18-10P
64
V
U
Power connector
Servo motor flange direction
L
KL
HF-SN52(B)J
125 (163)
71.3
HF-SN102(B)J
141 (179)
87.3
HF-SN152(B)J
163 (201)
109.3
[Unit: mm]
●●HF-SN202(B)J, HF-SN302(B)J
4-ø13.5 mounting hole
Use hexagonal cap
head bolts.
L
79
18
(Note 4)
176
3
45°
ø35 +0.010
0
75
(Note 3)
(Note 3)
Product List
34.5 (45)
ø2
30
(Note 3)
13
111
Encoder connector
(Note 3)
CM10-R10P
Electromagnetic brake connector
CM10-R2P (Note 3)
7 (Note 3)
KL
Main key
Position mark
Electromagnetic brake connector
Servo motor flange direction
00
ø2
(Note 3)
21.2
Power connector
MS3102A22-22P
Electromagnetic brake (Note 2)
124.9
Oil seal
(Note 3)
102.4 (Note 3)
(Note 3)
Cautions
(Note 3)
ø114.3
50.9
0
-0.025
(Note 3)
LVS/Wires
Electromagnetic brake connector
Servo motor flange direction
Variable dimensions (Note 4)
Model
Key
C D
B A
Electromagnetic brake (Note 2)
36
(PE)
W
Main key
Position mark
Options/Peripheral
Equipment
Encoder connector
CM10-R10P
99
81.4 (Note 3)
(Note 3)
50.9
ø110h7
Servo Motors
ø24h6
(Note 3)
130
3
50
(Note 3)
Servo Amplifiers
4-ø9 mounting hole
Use hexagonal cap
head bolts.
●●HF-SN52(B)J, HF-SN102(B)J, HF-SN152(B)J
(PE)
W
Key
C D
B A
V
36
77
42.5
U
Power connector
Servo motor flange direction
Model
Variable dimensions (Note 4)
L
KL
HF-SN202(B)J
148.5 (200.5)
91.5
HF-SN302(B)J
178.5 (230.5)
121.5
[Unit: mm]
Notes:1.For dimensions without tolerance, general tolerance applies.
2.The electromagnetic brake terminals do not have polarity.
3.Only for the models with electromagnetic brake.
4.Dimensions in brackets are for the models with electromagnetic brake.
5.Use a friction coupling to fasten a load.
2-10
Servo Motors
Servo Motor Sizing Example
1. Selection criteria
(1) Configurations
Feed speed of moving part
Feed length per cycle
Positioning time
Number of feed times
(Operating cycle
Reduction ratio
Moving part mass
Drive system efficiency
Friction coefficient
Ball screw lead
V0
Servo motor
Gear ratio 5 : 8
(2) Servo motor speed
V0
N0 =
PB
= ball screw diameter
= ball screw length
= gear diameter (servo motor shaft)
= gear diameter (load shaft)
= gear tooth thickness
20 mm
500 mm
25 mm
40 mm
10 mm
Selection criteria
Load torque Rated torque of servo motor
Moment of inertia of all loads JR × Moment of inertia of servo motor
JR: Recommended load to motor inertia ratio
Select the following servo motor to meet the criteria above.
HF-KN23J (rated torque: 0.64 N•m, max. torque: 1.9 N•m,
moment of inertia: 0.24 × 10-4 kg•m2)
R
- ts = 0.05 s
V0/60
ts: settling time. Here assumed 0.15 s.
tpsa = tpsd = t0 -
(4) Operating pattern
(4) Acceleration/deceleration torque
Torque required during acceleration
(JL / η + JM) × N0
TMa =
+ TL = 1.85 N•m
9.55 × 104 × t psa
JM: moment of inertia of servo motor
Speed
[r/min]
3000
Time [s]
0.05
tpsa
0.05
t psd
t0 1.0
ts
0.15
2. Selecting servo motor
(1) Load torque (converted into the servo motor shaft)
Travel distance per servo motor revolution
1
S = PB ×
= 10 mm
n
μ× W × g × S
2 × 103 π η
JL1 = W ×
(
S × 10
2π
-3
) = 1.52 × 10
2
-4
Ball screw
π × ρ × LB
1
JL2 =
× DB4 ×
32
n
ρ = 7.8 × 103 kg/m3 (iron)
kg•m2
-4
kg•m2
× DG24 ×
-4
kg•m2
Moment of inertia of all loads (converted into the servo motor
shaft)
JL = JL1 + JL2 + JL3 + JL4 = 1.87 × 10-4 kg•m2
= 0.41 N•m
Torque
[N•m]
0.23
0
0.05
0.75
0.05
0.15
Time [s]
1.5
(7) Result
( 1n ) = 0.08 × 10
2
TMa2 × t psa + TL2 × tc + TMd2 × t psd
tf
tc = t0 - ts - t psa - t psd
(6) Torque pattern
-0.86
Gear (servo motor shaft)
π × ρ × LG
JL3 =
× DG14 = 0.03 × 10-4 kg•m2
32
Gear (load shaft)
π × ρ × LG
JL4 =
32
Trms =
1.85
( ) = 0.24 × 10
2
(5) Continuous effective load torque
Continuous effective load torque must be equal to or lower than
the rated torque of the servo motor.
= 0.23 N•m
(2) Moment of inertia of load (converted into the servo motor shaft)
Moving part
Torque required during deceleration
(JL × η + JM) × N0
TMd = + TL = -0.86 N•m
9.55 × 104 × t psd
Torque required during acceleration/deceleration must be equal
to or lower than the max. torque of the servo motor.
1 cycle tf 1.5
TL =
DB
LB
DG1
DG2
LG
(3) Select a servo motor
1
30000
8
×
=
×
= 3000 r/min
1/n
16
5
(3) Acceleration/deceleration time constant
0
V0 = 30000 mm/min
R = 400 mm
t0 = within 1 s
40 times/min
tf = 1.5 s)
1/n = 5/8
W = 60 kg
η = 0.8
μ = 0.2
PB = 16 mm
Select the following:
Servo motor: HF-KN23J
Servo amplifier: MR-JE-20A
[Free capacity selection software]
Capacity selection software (MRZJW3-MOTSZ111E) does all the
calculations for you. The capacity selection software is available for
free download. Contact your local sales office for more details.
* MRZJW3-MOTSZ111E software version C6 or later is compatible.
2-11
3
Basic Cable Configurations for Servo Motors.............................3-1
Configuration Example for Servo Motors....................................3-3
Details of Optional Cables and Connectors for Servo Motors.....3-9
Products on the Market for Servo Motors..................................3-11
Configuration Example for Servo Amplifiers..............................3-15
Details of Optional Cables and Connectors for Servo Amplifiers...3-17
Regenerative Option.................................................................3-18
Junction Terminal Block.............................................................3-20
Radio Noise Filter......................................................................3-20
Line Noise Filter........................................................................3-20
Data Line Filter..........................................................................3-20
Surge Killer................................................................................3-20
EMC Filter..................................................................................3-21
Power Factor Improving Reactor...............................................3-22
Servo Support Software............................................................3-23
Options/Peripheral Equipment
Options/Peripheral Equipment
Basic Cable Configurations for Servo Motors
Necessary optional cables and connectors vary depending on the servo motor series.
Refer to the following tables for necessary options.
Selecting options for servo motor
Use the cables in the following tables.
For the cable descriptions, refer to the relevant numbers in each list.
Capacity
Servo motor
Encoder cable
Small capacity HF-KN
Column A in encoder cable list
Medium
capacity
Column B in encoder cable list
HF-SN
Reference list
Servo motor power cable
Column A in servo motor power
cable list
Column B in servo motor power
cable list
Notes: 1
.An electromagnetic brake cable is required only for servo motor with electromagnetic brake.
Electromagnetic brake cable (Note 1)
Column A in electromagnetic
brake cable list
Column B in electromagnetic
brake cable list
Encoder cable list
Cable length IP rating (Note 1)
10 m or
shorter
(direct
connection
type)
IP65
IP20
A
Exceeding
10 m
(junction
type)
IP65
B
2 m to 50 m
2 m to 30 m
IP67
Cable lead
Bending life
out direction
Long
In direction
bending life
of load side
Standard
In opposite Long
direction of bending life
load side
Standard
Long
In direction bending life
of load side
Standard
In opposite
direction of
load side
Long
bending life
Standard
Long
In direction bending life
of load side
Standard
In opposite
direction of
load side
-
Long
bending life
Standard
Long
bending life
Standard
Model
MR-J3ENCBL_M-A1-H
MR-J3ENCBL_M-A1-L
MR-J3ENCBL_M-A2-H
MR-J3ENCBL_M-A2-L
Two types of cables are required:
MR-J3JCBL03M-A1-L, MR-EKCBL_M-H
Two types of cables are required:
MR-J3JCBL03M-A1-L, MR-EKCBL_M-L
Two types of cables are required:
MR-J3JCBL03M-A2-L, MR-EKCBL_M-H
Two types of cables are required:
MR-J3JCBL03M-A2-L, MR-EKCBL_M-L
Two types of cables are required:
MR-J3JSCBL03M-A1-L, MR-J3ENSCBL_M-H
Two types of cables are required:
MR-J3JSCBL03M-A1-L, MR-J3ENSCBL_M-L
Two types of cables are required:
MR-J3JSCBL03M-A2-L, MR-J3ENSCBL_M-H
Two types of cables are required:
MR-J3JSCBL03M-A2-L, MR-J3ENSCBL_M-L
MR-J3ENSCBL_M-H
MR-J3ENSCBL_M-L
Reference
Note
p. 3-5
p. 3-5
p. 3-5
p. 3-5
Select one from
this list.
pp. 3-5
and 3-6
pp. 3-5
and 3-6
p. 3-6
Select one from
this list.
Notes:1.The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo
amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all.
3-1
Cable length IP rating (Note 1)
Exceeding
10 m
(junction
type)
IP65
IP55
IP rating (Note 1)
HF-SN52J, 102J, 152J
HF-SN202J, 302J
MR-PWS1CBL_M-A1-H
MR-PWS1CBL_M-A1-L
MR-PWS1CBL_M-A2-H
MR-PWS1CBL_M-A2-L
Connect a user-fabricated cable to
MR-PWS2CBL03M-A1-L (optional cable).
Connect a user-fabricated cable to
MR-PWS2CBL03M-A2-L (optional cable).
Model
Fabricate a cable that fits to MR-PWCNS4
(optional connector set).
Fabricate a cable that fits to MR-PWCNS5
(optional connector set).
Reference
Note
p. 3-7
p. 3-7
p. 3-7
Select one from
this list.
p. 3-7
Reference
Note
p. 3-7
p. 3-7
Select one that is
compatible with the
servo motor.
Reference
Note
Electromagnetic brake cable list
Cable length IP rating (Note 1)
Exceeding
10 m
(junction
type)
IP55
IP rating (Note 1)
B IP67
Compatible servo motor
HF-SN series
MR-BKS1CBL_M-A1-H
MR-BKS1CBL_M-A1-L
MR-BKS1CBL_M-A2-H
MR-BKS1CBL_M-A2-L
Connect a user-fabricated cable to
MR-BKS2CBL03M-A1-L (optional cable).
Connect a user-fabricated cable to
MR-BKS2CBL03M-A2-L (optional cable).
Model
Fabricate a cable that fits to MR-BKCNS1
(optional connector set) (straight type).
Fabricate a cable that fits to MR-BKCNS1A
(optional connector set) (angle type).
p. 3-8
p. 3-8
p. 3-8
Select one from
this list.
p. 3-8
Reference
p. 3-8
p. 3-8
Product List
IP65
Model
LVS/Wires
A
10 m or
shorter
(direct
connection
type)
Cable lead
Bending life
out direction
Long
In direction
bending life
of load side
Standard
In opposite Long
direction of bending life
load side
Standard
In direction
of load side
In opposite Standard
direction of
load side
Options/Peripheral
Equipment
B IP67
Compatible servo motor
Model
Servo Motors
A
10 m or
shorter
(direct
connection
type)
Cable lead
Bending life
out direction
Long
In direction
bending life
of load side
Standard
In opposite Long
direction of bending life
load side
Standard
In direction
of load side
In opposite Standard
direction of
load side
Servo Amplifiers
Servo motor power cable list
Note
Select one from
this list.
Notes:1.The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo
amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all.
Cautions
3-2
Options/Peripheral Equipment
Configuration Example for Servo Motors
For HF-KN servo motor series: encoder cable length 10 m or shorter
●●For leading the cables out in direction of load side (Note 1)
Power cable
To servo amplifier CNP1 connector
(12)
Electromagnetic brake cable
(18)
Encoder cable
To servo amplifier CN2 connector
(1)
Servo motor
●●For leading the cables out in opposite direction of load side (Note 1)
Power cable
(13)
Electromagnetic brake cable
(19)
Encoder cable
(2)
Servo motor
Notes:1.Cables for leading two different directions may be used for one servo motor.
3-3
To servo amplifier CNP1 connector
To servo amplifier CN2 connector
Configuration Example for Servo Motors (Note 5)
Servo Amplifiers
For HF-KN servo motor series: encoder cable length over 10 m
●●For leading the cables out in direction of load side (Note 4)
(14) Power cable
To servo amplifier CNP1 connector
(Note 2)
(20) Electromagnetic brake cable
(Note 3)
(5)
Servo Motors
Encoder cable
(3) (Note 1)
To servo amplifier CN2 connector
(6)
Encoder cable
(9)
( 7 ) (Note 1)
Options/Peripheral
Equipment
(10)
Servo motor
●●For leading the cables out in opposite direction of load side (Note 4)
(15) Power cable
To servo amplifier CNP1 connector
LVS/Wires
(Note 2)
(21) Electromagnetic brake cable
(Note 3)
Encoder cable
(4) (Note 1)
(5)
To servo amplifier CN2 connector
(6)
Encoder cable
Product List
(9)
(8) (Note 1)
(10)
Servo motor
For HF-SN servo motor series
Cautions
Power connector set
For 1 kW or smaller servo amplifier: to CNP1 connector
For 2 kW or larger servo amplifier: to CNP2 connector
(16) (17)
Electromagnetic brake connector set
(22)
(23)
Encoder cable
To servo amplifier CN2 connector
(9)
(10)
Servo motor
(11)
Notes:1.This cable does not have a long bending life. Thus, be sure to fix the cable before using.
2.Relay a cable using MR-PWS2CBL03M-A1-L or MR-PWS2CBL03M-A2-L. This cable does not have a long bending life. Thus, be sure to fix the cable before using.
3.Relay a cable using MR-BKS2CBL03M-A1-L or MR-BKS2CBL03M-A2-L. This cable does not have a long bending life. Thus, be sure to fix the cable before using.
4.Cables for leading two different directions may be used for one servo motor.
5.Cables drawn with dashed lines need to be fabricated by user. Refer to "HF-KN HF-SN Servo Motor Instruction Manual" for fabricating the cables.
3-4
Options/Peripheral Equipment
Cables and Connectors for Servo Motor Encoder
Refer to "Details of Optional Cables and Connectors for Servo Motors" in this catalog for the detailed models.
IP rating
MR-J3ENCBL2M-A1-H *1
MR-J3ENCBL5M-A1-H *1
MR-J3ENCBL10M-A1-H *1
MR-J3ENCBL2M-A1-L *1
MR-J3ENCBL5M-A1-L *1
MR-J3ENCBL10M-A1-L *1
MR-J3ENCBL2M-A2-H *1
MR-J3ENCBL5M-A2-H *1
MR-J3ENCBL10M-A2-H *1
MR-J3ENCBL2M-A2-L *1
MR-J3ENCBL5M-A2-L *1
MR-J3ENCBL10M-A2-L *1
Cable
length
2m
5m
10 m
2m
5m
10 m
2m
5m
10 m
2m
5m
10 m
IP65
For HF-KN
(direct connection
type)
MR-J3JCBL03M-A1-L *1
0.3 m
IP20
MR-J3JCBL03M-A2-L *1
0.3 m
MR-EKCBL20M-H *1
MR-EKCBL30M-H (Note 3) *1
MR-EKCBL40M-H (Note 3) *1
MR-EKCBL50M-H (Note 3) *1
MR-EKCBL20M-L *1
MR-EKCBL30M-L (Note 3) *1
20 m
30 m
40 m
50 m
20 m
30 m
Item
(1)
Model
Encoder cable (Note 2)
(load-side lead)
Encoder cable (Note 2)
(2) (opposite to load-side
lead)
Encoder cable (Note 2)
(load-side lead)
Encoder cable (Note 2)
(4) (opposite to load-side
lead)
(3)
(5) Encoder cable (Note 2)
(Note 1)
IP65
Application
Description
For HF-KN
(direct connection
type)
Encoder connector
Servo amplifier connector
For HF-KN
(junction type)
Encoder connector
Junction connector
IP20
For HF-KN
(junction type)
Use this in combination with (5) or (6).
IP20
For HF-KN
(junction type)
Junction connector
Use this in combination with (3) or (4).
Junction connector
(6) Encoder connector set MR-ECNM
(7)
Encoder cable (Note 2)
(load-side lead)
Encoder cable
(8) (opposite to load-side
lead)
-
IP20
MR-J3JSCBL03M-A1-L *1
0.3 m
(Note 4)
MR-J3JSCBL03M-A2-L *1
0.3 m
(Note 4)
(Note 2)
For HF-KN
(junction type)
Servo amplifier connector
Servo amplifier connector
Use this in combination with (3) or (4).
Applicable cable
Wire size: 0.3 mm2 (AWG 22)
Cable OD: 8.2 mm
Crimping tool (91529-1) is required.
IP65
For HF-KN
(junction type)
Encoder connector
IP65
For HF-KN
(junction type)
Use this in combination with (9) or (10).
Junction connector
Notes: 1
.The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo
amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all.
2.-H and -L indicate a bending life. -H indicates a long bending life, and -L indicates a standard bending life.
3.This encoder cable is available in four-wire type. Parameter setting is required to use the four-wire type encoder cable. Refer to "MR-JE-_A Servo Amplifier Instruction
Manual" for details.
4.The encoder cable is rated IP65 while the junction connector itself is rated IP67.
For unlisted lengths
*1.For unlisted lengths of the cables, contact Mitsubishi Electric System & Service Co., Ltd. FA PRODUCT DIVISION by email: oss-ip@melsc.jp
3-5
Cables and Connectors for Servo Motor Encoder
Item
MR-J3SCNS
-
IP rating
(Note 1)
IP67
IP67
Application
For HF-KN
(junction type)
For HF-SN
(direct connection
type)
For HF-KN
(junction type)
For HF-SN
(direct connection
type)
(straight type)
Description
Junction connector or
encoder connector
Use this in combination with (7) or (8) for HF-KN
series.
Junction connector or
encoder connector
Applicable cable
Wire size: 0.5 mm2 (AWG 20) or smaller
Cable OD: 5.5 mm to 9.0 mm (Note 3)
-
IP67
For HF-SN
(angle type)
Servo amplifier connector
LVS/Wires
MR-J3SCNSA *2
Servo amplifier
connector
Use this in combination with (7) or (8) for HF-KN
series.
Encoder connector
Encoder connector set
(11) (one-touch connection
type)
Servo amplifier
connector
Options/Peripheral
Equipment
Encoder connector set
(10) (one-touch connection
type)
MR-J3ENSCBL2M-H *1
MR-J3ENSCBL5M-H *1
MR-J3ENSCBL10M-H *1
MR-J3ENSCBL20M-H *1
MR-J3ENSCBL30M-H *1
MR-J3ENSCBL40M-H *1
MR-J3ENSCBL50M-H *1
MR-J3ENSCBL2M-L *1
MR-J3ENSCBL5M-L *1
MR-J3ENSCBL10M-L *1
MR-J3ENSCBL20M-L *1
MR-J3ENSCBL30M-L *1
Cable
length
2m
5m
10 m
20 m
30 m
40 m
50 m
2m
5m
10 m
20 m
30 m
Servo Motors
(9) Encoder cable (Note 2)
Model
Servo Amplifiers
Refer to "Details of Optional Cables and Connectors for Servo Motors" in this catalog for the detailed models.
Applicable cable
Wire size: 0.5 mm2 (AWG 20) or smaller
Cable OD: 5.5 mm to 9.0 mm (Note 3)
Product List
Notes: 1
.The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo
amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all.
2.-H and -L indicate a bending life. -H indicates a long bending life, and -L indicates a standard bending life.
3.Cable clamps and bushings for cable OD of 5.5 mm to 7.5 mm and of 7.0 mm to 9.0 mm are included in the set.
For unlisted lengths and fabricating cables
*1.For unlisted lengths of the cables, contact Mitsubishi Electric System & Service Co., Ltd. FA PRODUCT DIVISION by email: oss-ip@melsc.jp
*2.For fabricating encoder cables with these connectors, contact Mitsubishi Electric System & Service Co., Ltd. FA PRODUCT DIVISION by email: oss-ip@melsc.jp
Cautions
3-6
Options/Peripheral Equipment
Cables and Connectors for Servo Motor Power
Refer to "Details of Optional Cables and Connectors for Servo Motors" in this catalog for the detailed models.
IP rating
MR-PWS1CBL2M-A1-H *1
MR-PWS1CBL5M-A1-H *1
MR-PWS1CBL10M-A1-H *1
MR-PWS1CBL2M-A1-L *1 (Note 3)
MR-PWS1CBL5M-A1-L *1 (Note 3)
MR-PWS1CBL10M-A1-L *1 (Note 3)
MR-PWS1CBL2M-A2-H *1
MR-PWS1CBL5M-A2-H *1
MR-PWS1CBL10M-A2-H *1
MR-PWS1CBL2M-A2-L *1 (Note 3)
MR-PWS1CBL5M-A2-L *1 (Note 3)
MR-PWS1CBL10M-A2-L *1 (Note 3)
Cable
length
2m
5m
10 m
2m
5m
10 m
2m
5m
10 m
2m
5m
10 m
MR-PWS2CBL03M-A1-L
0.3 m
IP55
For HF-KN
(junction type)
MR-PWS2CBL03M-A2-L
0.3 m
IP55
For HF-KN
(junction type)
Item
(12)
Power cable (Note 2)
(load-side lead)
Power cable (Note 2)
(13) (opposite to load-side
lead)
Power cable
(load-side lead)
Power cable (Note 2)
(15) (opposite to load-side
lead)
(14)
(Note 2)
Model
(Note 1)
IP65
Application
Description
For HF-KN
(direct connection
type)
Power connector
Lead-out
IP65
For HF-KN
(direct connection
type)
* The cable is not shielded.
Power connector
Lead-out
* The cable is not shielded.
Power connector
(16) Power connector set
MR-PWCNS4 *2
-
IP67
For HF-SN52J, 102J,
152J
Applicable cable
Wire size: 2 mm2 to 3.5 mm2 (AWG 14 to 12)
Cable OD: 10.5 mm to 14.1 mm
Power connector
(17) Power connector set
MR-PWCNS5 *2
-
IP67
For HF-SN202J, 302J
Applicable cable
Wire size: 5.5 mm2 to 8 mm2 (AWG 10 to 8)
Cable OD: 12.5 mm to 16 mm
Notes: 1
.The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo
amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all.
2.-H and -L indicate a bending life. -H indicates a long bending life, and -L indicates a standard bending life.
3.Shielded power cable MR-PWS3CBL_M-A_-L is also available. Contact your local sales office.
For unlisted lengths and fabricating cables
*1.For unlisted lengths of the cables, contact Mitsubishi Electric System & Service Co., Ltd. FA PRODUCT DIVISION by email: oss-ip@melsc.jp
*2.For fabricating power cables and electromagnetic brake cables, contact Mitsubishi Electric System & Service Co., Ltd. FA PRODUCT DIVISION by email: oss-ip@melsc.jp
3-7
Cables and Connectors for Servo Motor Electromagnetic Brake
IP rating
MR-BKS1CBL2M-A1-H *1
MR-BKS1CBL5M-A1-H *1
MR-BKS1CBL10M-A1-H *1
MR-BKS1CBL2M-A1-L *1
MR-BKS1CBL5M-A1-L *1
MR-BKS1CBL10M-A1-L *1
MR-BKS1CBL2M-A2-H *1
MR-BKS1CBL5M-A2-H *1
MR-BKS1CBL10M-A2-H *1
MR-BKS1CBL2M-A2-L *1
MR-BKS1CBL5M-A2-L *1
MR-BKS1CBL10M-A2-L *1
Cable
length
2m
5m
10 m
2m
5m
10 m
2m
5m
10 m
2m
5m
10 m
MR-BKS2CBL03M-A1-L
0.3 m
IP55
For HF-KN
(junction type)
MR-BKS2CBL03M-A2-L
0.3 m
IP55
For HF-KN
(junction type)
Item
Electromagnetic
(18) brake cable (Note 2)
(load-side lead)
For HF-KN
(direct connection
type)
Electromagnetic brake connector
Lead-out
IP65
For HF-KN
(direct connection
type)
* The cable is not shielded.
Electromagnetic brake connector
Lead-out
* The cable is not shielded.
Electromagnetic brake connector
MR-BKCNS1 *2
-
IP67
For HF-SN
(straight type)
Applicable cable
Wire size: 1.25 mm2 (AWG 16) or smaller
Cable OD: 9.0 mm to 11.6 mm
Electromagnetic brake connector
MR-BKCNS1A *2
-
IP67
For HF-SN
(angle type)
Applicable cable
Wire size: 1.25 mm2 (AWG 16) or smaller
Cable OD: 9.0 mm to 11.6 mm
Product List
Electromagnetic brake
connector set
(23)
(one-touch connection
type)
Description
LVS/Wires
Electromagnetic brake
connector set
(22)
(one-touch connection
type)
IP65
Application
Options/Peripheral
Equipment
Electromagnetic
(20) brake cable (Note 2)
(load-side lead)
Electromagnetic
brake cable (Note 2)
(21)
(opposite to load-side
lead)
(Note 1)
Servo Motors
Electromagnetic
brake cable (Note 2)
(19)
(opposite to load-side
lead)
Model
Servo Amplifiers
Refer to "Details of Optional Cables and Connectors for Servo Motors" in this catalog for the detailed models.
Notes: 1
.The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo
amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all.
2.-H and -L indicate a bending life. -H indicates a long bending life, and -L indicates a standard bending life.
For unlisted lengths and fabricating cables
*1.For unlisted lengths of the cables, contact Mitsubishi Electric System & Service Co., Ltd. FA PRODUCT DIVISION by email: oss-ip@melsc.jp
*2.For fabricating power cables and electromagnetic brake cables, contact Mitsubishi Electric System & Service Co., Ltd. FA PRODUCT DIVISION by email: oss-ip@melsc.jp
Cautions
3-8
Options/Peripheral Equipment
Details of Optional Cables and Connectors for Servo Motors
Model
MR-J3ENCBL_M-A1-H (Note 2)
MR-J3ENCBL_M-A1-L (Note 2)
MR-J3ENCBL_M-A2-H (Note 2)
MR-J3ENCBL_M-A2-L (Note 2)
Model
MR-J3JCBL03M-A1-L (Note 2)
MR-J3JCBL03M-A2-L (Note 2)
Model
MR-EKCBL_M-H
MR-EKCBL_M-L
MR-ECNM
Model
MR-J3JSCBL03M-A1-L (Note 2)
MR-J3JSCBL03M-A2-L (Note 2)
Model
MR-J3ENSCBL_M-H (Note 2)
MR-J3ENSCBL_M-L (Note 2)
Model
MR-J3SCNS (Note 2)
Encoder connector
2174053-1
(TE Connectivity Ltd. Company)
Servo amplifier connector
Receptacle: 36210-0100PL
Shell kit: 36310-3200-008
(3M)
or
Connector set: 54599-1019
(Molex)
Encoder connector
2174053-1
(TE Connectivity Ltd. Company)
Junction connector
Contact: 1473226-1 (with ring)
Housing: 1-172169-9
Cable clamp: 316454-1
(TE Connectivity Ltd. Company)
Junction connector
Housing: 1-172161-9
Connector pin: 170359-1
(TE Connectivity Ltd. Company)
or an equivalent product
Cable clamp: MTI-0002
(Toa Electric Industrial Co., Ltd.)
Servo amplifier connector
Receptacle: 36210-0100PL
Shell kit: 36310-3200-008
(3M)
or
Connector set: 54599-1019
(Molex)
Encoder connector
2174053-1
(TE Connectivity Ltd. Company)
Junction connector
Cable receptacle: CM10-CR10P-M
(DDK Ltd.)
Encoder connector
For 10 m or shorter cable
Straight plug: CMV1-SP10S-M1
Socket contact: CMV1-#22ASC-C1-100
For 20 m or longer cable
Straight plug: CMV1-SP10S-M1 (long bending life)
CMV1-SP10S-M2 (standard)
Socket contact: CMV1-#22ASC-C2-100
(DDK Ltd.)
Servo amplifier connector
Receptacle: 36210-0100PL
Shell kit: 36310-3200-008
(3M)
or
Connector set: 54599-1019
(Molex)
Junction connector or encoder connector
Straight plug: CMV1-SP10S-M2 (Note 1)
Socket contact: CMV1-#22ASC-S1-100
(DDK Ltd.)
Servo amplifier connector
Receptacle: 36210-0100PL
Shell kit: 36310-3200-008
(3M)
or
Connector set: 54599-1019
(Molex)
Notes:1.Cable clamps and bushings for cable OD of 5.5 mm to 7.5 mm and of 7.0 mm to 9.0 mm are included in the set.
2.The cable or the connector set may contain different connectors but still usable.
3-9
Details of Optional Cables and Connectors for Servo Motors
MR-J3SCNSA (Note 2)
MR-PWS2CBL03M-A1-L (Note 2)
MR-PWS2CBL03M-A2-L (Note 2)
Model
Receptacle: 36210-0100PL
Shell kit: 36310-3200-008
(3M)
or
Connector set: 54599-1019
(Molex)
Power connector
Plug: KN4FT04SJ1-R
Socket contact: ST-TMH-S-C1B-100-(A534G)
(Japan Aviation Electronics Industry, Limited)
Power connector
Options/Peripheral
Equipment
Model
Angle plug: CMV1-AP10S-M2 (Note 1)
Socket contact: CMV1-#22ASC-S1-100
(DDK Ltd.)
Servo amplifier connector
Servo Motors
Model
MR-PWS1CBL_M-A1-H (Note 2)
MR-PWS1CBL_M-A1-L (Note 2)
MR-PWS1CBL_M-A2-H (Note 2)
MR-PWS1CBL_M-A2-L (Note 2)
Encoder connector
Servo Amplifiers
Model
Plug: KN4FT04SJ2-R
Socket contact: ST-TMH-S-C1B-100-(A534G)
(Japan Aviation Electronics Industry, Limited)
Power connector
Plug: CE05-6A18-10SD-D-BSS (straight)
Cable clamp: CE3057-10A-1-D
(DDK Ltd.)
MR-PWCNS4
LVS/Wires
Model
Power connector
Plug: CE05-6A22-22SD-D-BSS (straight)
Cable clamp: CE3057-12A-1-D
(DDK Ltd.)
MR-PWCNS5
Model
Model
MR-BKCNS1 (Note 2)
Model
MR-BKCNS1A (Note 2)
Plug: JN4FT02SJ1-R
Socket contact: ST-TMH-S-C1B-100-(A534G)
(Japan Aviation Electronics Industry, Limited)
Electromagnetic brake connector
Plug: JN4FT02SJ2-R
Socket contact: ST-TMH-S-C1B-100-(A534G)
(Japan Aviation Electronics Industry, Limited)
Cautions
MR-BKS2CBL03M-A1-L
MR-BKS2CBL03M-A2-L
Electromagnetic brake connector
Product List
Model
MR-BKS1CBL_M-A1-H
MR-BKS1CBL_M-A1-L
MR-BKS1CBL_M-A2-H
MR-BKS1CBL_M-A2-L
Electromagnetic brake connector
Straight plug: CMV1-SP2S-L
Socket contact: CMV1-#22BSC-S2-100
(DDK Ltd.)
Electromagnetic brake connector
Angle plug: CMV1-AP2S-L
Socket contact: CMV1-#22BSC-S2-100
(DDK Ltd.)
Notes:1.Cable clamps and bushings for cable OD of 5.5 mm to 7.5 mm and of 7.0 mm to 9.0 mm are included in the set.
2.The cable or the connector set may contain different connectors but still usable.
3-10
Options/Peripheral Equipment
Products on the Market for Servo Motors
Contact the relevant manufacturers directly.
When fabricating a cable with the following connectors, refer to the relevant manufacturers' instruction manuals for wiring and
assembling procedures.
Encoder connector (servo amplifier-side)
Application
Servo amplifier
CN2 connector
Connector (3M)
Receptacle: 36210-0100PL
Shell kit: 36310-3200-008
Connector (Molex)
54599-1019 (gray)
54599-1016 (black)
Encoder connector for HF-KN series
Applicable
servo motor
HF-KN
Feature (Note 1)
IP65
Connector
(TE Connectivity
Ltd. Company)
2174053-1
Crimping tools
(TE Connectivity Ltd. Company)
Applicable cable example
Wire size: 0.13 mm2 to 0.33 mm2 (AWG 26 to 22)
Cable OD: 6.8 mm to 7.4 mm
For ground clip: 1596970-1
Wire example:
For receptacle contact: 1596847-1 Fluorine resin wire (Vinyl jacket cable
TPE. SVP 70/0.08(AWG#22)-3P KB-2237-2
Bando Densen Co., Ltd. (Note 2) or an equivalent product)
Straight type
Angle type
Encoder connector for HF-SN series
Applicable
servo motor
HF-SN
Feature (Note 1)
IP67
Contact
Solder type
Press bonding type
Type
Type of connection
Straight
One-touch
connection type
Angle
One-touch
connection type
Connector (DDK Ltd.)
Plug
CMV1-SP10S-M1
CMV1-SP10S-M2
CMV1-AP10S-M1
CMV1-AP10S-M2
Socket contact (DDK Ltd.)
CMV1-#22ASC-S1-100
CMV1-#22ASC-C1-100
CMV1-#22ASC-C2-100
Applicable cable example
Cable OD [mm]
5.5 to 7.5
Select from solder or press
7.0 to 9.0
bonding type.
5.5 to 7.5
(Refer to the table below.)
7.0 to 9.0
Socket contact
Wire size (Note 3)
0.5 mm (AWG 20) or smaller
0.2 mm2 to 0.5 mm2 (AWG 24 to 20)
Crimping tool (357J-53162T) is required.
0.08 mm2 to 0.2 mm2 (AWG 28 to 24)
Crimping tool (357J-53163T) is required.
2
Notes: 1
.The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo
amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all.
2.Contact Toa Electric Industrial Co., Ltd.
3.The wire size shows wiring specification of the connector.
3-11
Products on the Market for Servo Motors
Unlisted lengths of cables between servo amplifier and servo motor, EMC cables, and special cables for connecting servo amplifier
and servo motor with multiple cables are available. Contact Mitsubishi Electric System & Service Co., Ltd. FA PRODUCT DIVISION
by email: oss-ip@melsc.jp
Cable chain
(moving part)
Control cabinet
Servo Motors
Example) Configuration using three encoder junction cables
•• Replacing only the cable of the moving part in the cable chain is possible.
•• Resetting after transporting a machine is easy because the servo amplifier side and the servo motor side can be separated.
Machine side
Servo amplifier
MR-JE-A
+
+
+
Options/Peripheral
Equipment
+
CN2
HF-KN series
+
Servo Amplifiers
Application of connecting encoder junction cable
+
LVS/Wires
HF-SN series
Product List
Cautions
3-12
Options/Peripheral Equipment
Products on the Market for Servo Motors
Contact the relevant manufacturers directly.
When fabricating a cable with the following connectors, refer to the relevant manufacturers' instruction manuals for wiring and
assembling procedures.
Power connector for HF-KN series
Applicable
servo motor
HF-KN
Feature
(Note 1)
Connector
(Japan Aviation Electronics
Industry, Limited)
Crimping tools
(Japan Aviation Electronics
Industry, Limited)
Plug: KN4FT04SJ1-R
For contactor:
Socket contact:
CT160-3-TMH5B
ST-TMH-S-C1B-100-(A534G)
IP65
Applicable cable example
Wire size: 0.3 mm2 to 0.75 mm2 (AWG 22 to 18)
Cable OD: 5.3 mm to 6.5 mm
Wire example:
Fluorine resin wire (Vinyl jacket cable
RMFES-A (CL3X) AWG 19, 4 cores
Dyden Corporation (Note 4) or an equivalent product)
Straight type
Plug
Cable
clamp
Angle type
Plug
Cable
clamp
Power connector for HF-SN series
Applicable servo
motor
HF-SN52J, 102J,
152J
Feature (Note 1)
IP67
EN compliant
CE05-6A18-10SD-D-BSS
General
environment
(Note 2)
HF-SN202J, 302J
Type
IP67
EN compliant
D/MS3106B18-10S
Straight
CE05-6A22-22SD-D-BSS
General
environment
D/MS3106B22-22S
(Note 2)
HF-SN52J, 102J,
152J
IP67
EN compliant
HF-SN202J, 302J
CE05-8A18-10SD-D-BAS
General
environment
(Note 2)
IP67
EN compliant
General
environment
(Note 2)
Plug (with backshell)
(DDK Ltd.)
Model
D/MS3108B18-10S
Angle
CE05-8A22-22SD-D-BAS
D/MS3108B22-22S
Cable clamp
(DDK Ltd.)
Model
CE3057-10A-2-D
CE3057-10A-1-D
D/MS3057-10A
CE3057-12A-2-D
CE3057-12A-1-D
D/MS3057-12A
CE3057-10A-2-D
CE3057-10A-1-D
D/MS3057-10A
CE3057-12A-2-D
CE3057-12A-1-D
D/MS3057-12A
Applicable cable example
Wire size (Note 3)
Cable OD [mm]
2.2 mm2 to 3.5 mm2 8.5 to 11
(AWG 14 to 12)
10.5 to 14.1
2.2 mm2 to 3.5 mm2 14.3 or smaller
(AWG 14 to 12)
(bushing ID)
5.5 mm2 to 8 mm2
(AWG 10 to 8)
9.5 to 13
5.5 mm2 to 8 mm2
(AWG 10 to 8)
15.9 or smaller
(bushing ID)
12.5 to 16
2.2 mm2 to 3.5 mm2 8.5 to 11
(AWG 14 to 12)
10.5 to 14.1
2.2 mm2 to 3.5 mm2 14.3 or smaller
(AWG 14 to 12)
(bushing ID)
5.5 mm2 to 8 mm2
(AWG 10 to 8)
9.5 to 13
5.5 mm2 to 8 mm2
(AWG 10 to 8)
15.9 or smaller
(bushing ID)
12.5 to 16
Notes: 1
.The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo
amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all.
2.Not compliant with EN.
3.The wire size shows wiring specification of the connector. Refer to "Selection Example in HIV Wires for Servo Motors" in this catalog for examples of wire size selection.
4.Contact Taisei Co., Ltd.
3-13
Products on the Market for Servo Motors
Servo Amplifiers
Contact the relevant manufacturers directly.
When fabricating a cable with the following connectors, refer to the relevant manufacturers' instruction manuals for wiring and
assembling procedures.
Electromagnetic brake connector for HF-KN series
Applicable
servo motor
IP65
Connector
(Japan Aviation Electronics
Industry, Limited)
Crimping tool
(Japan Aviation Electronics
Industry, Limited)
Plug: JN4FT02SJ1-R
For contactor:
Socket contact:
CT160-3-TMH5B
ST-TMH-S-C1B-100-(A534G)
Applicable cable example
Wire size: 0.3 mm2 to 0.5 mm2 (AWG 22 to 20)
Cable OD: 3.6 mm to 4.8 mm
Wire example:
Fluorine resin wire (Vinyl jacket cable
RMFES-A (CL3X) AWG 20, 2 cores
Dyden Corporation (Note 2) or an equivalent product)
Angle type
Electromagnetic brake connector for HF-SN series
Applicable
servo motor
Feature (Note 1)
Type
Straight
One-touch
connection type
IP67
Angle
One-touch
connection type
Connector (DDK Ltd.)
Plug
CMV1-SP2S-S
CMV1-SP2S-M1
CMV1-SP2S-M2
CMV1-SP2S-L
CMV1-AP2S-S
CMV1-AP2S-M1
CMV1-AP2S-M2
CMV1-AP2S-L
Socket contact (DDK Ltd.)
CMV1-#22BSC-S2-100
Press bonding type
CMV1-#22BSC-C3-100
Select from solder
or press bonding type.
(Refer to the table below.)
Applicable cable example
Cable OD [mm]
4.0 to 6.0
5.5 to 7.5
7.0 to 9.0
9.0 to 11.6
4.0 to 6.0
5.5 to 7.5
7.0 to 9.0
9.0 to 11.6
Wire size (Note 3)
1.25 mm (AWG 16) or smaller
0.5 mm2 to 1.25 mm2 (AWG 20 to 16)
Crimping tool (357J-53164T) is required.
2
Notes: 1
.The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo
amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all.
2.Contact Taisei Co., Ltd.
3.The wire size shows wiring specification of the connector. Refer to "Selection Example in HIV Wires for Servo Motors" in this catalog for examples of wire size selection.
Product List
Contact
Solder type
Socket contact
LVS/Wires
HF-SN
Type of connection
Options/Peripheral
Equipment
Straight type
Servo Motors
HF-KN
Feature (Note 1)
Cautions
3-14
Options/Peripheral Equipment
Configuration Example for Servo Amplifiers
Servo amplifier 1 kW or smaller
Servo amplifier
Controller
QD70P
QD70D
QD75P_N
QD75D_N
LD75P
LD75D
FX3U
FX3UC
FX3G
FX3GC
FX2N-_GM
FX2N-_PG
FX1S
CN3
(3)
(5)
CN1
Setup software
MR Configurator2
(SW1DNC-MRC2-E)
(4)
CN2
Junction terminal block
MR-TB50 (Note 1)
CNP1
To servo motor encoder
(1)
Servo amplifier 2 kW and 3 kW
Controller
QD70P
QD70D
QD75P_N
QD75D_N
LD75P
LD75D
FX3U
FX3UC
FX3G
FX3GC
FX2N-_GM
FX2N-_PG
FX1S
(3)
Servo amplifier
(4)
CNP1
CN3
(5)
Junction terminal block
MR-TB50 (Note 1)
CN1
(2)
CNP2
CN2
To servo motor encoder
Notes:1.Refer to "Junction Terminal Block" in this catalog.
3-15
Setup software
MR Configurator2
(SW1DNC-MRC2-E)
Cables and Connectors for Servo Amplifiers
Servo Amplifiers
Refer to "Details of Optional Cables and Connectors for Servo Amplifiers" in this catalog for the detailed models.
Item
Cable
length
IP rating
Application
Description
CNP1 connector
MR-JECNP1-01
-
-
For MR-JE-100A or
smaller
Applicable wire size (Note 1): AWG 18 to 14
Insulator OD: up to 3.9 mm
CNP1 connector
MR-JECNP1-02
-
For MR-JE-200A/
MR-JE-300A
(2)
Servo amplifier
CNP2 power
connector (Note 2)
(insertion type)
For CN1
(4)
Junction terminal
block cable
Applicable wire size (Note 1): AWG 16 to 10
Insulator OD: up to 4.7 mm
CNP2 connector
-
-
MR-J3CN1
-
-
For MR-JE-A
-
For connecting
MR-JE-A and
MR-TB50
-
For MR-JE-A
MR-J2M-CN1TBL05M
0.5 m
MR-J2M-CN1TBL1M
1m
Personal computer
(5) communication cable MR-J3USBCBL3M
(USB cable)
3m
Applicable wire size (Note 1): AWG 16 to 10
Insulator OD: up to 4.7 mm
Servo amplifier connector
Junction terminal block
connector
Servo amplifier
connector
Servo amplifier connector Personal computer
mini-B connector (5-pin)
connector A connector
Product List
For CN3
MR-JECNP2-02
LVS/Wires
(3) Connector set
Open tool
Options/Peripheral
Equipment
For CNP1/CNP2
Servo amplifier
CNP1 power
connector (Note 2)
(insertion type)
Open tool
Servo Motors
For CNP1
Servo amplifier
CNP1 power
(1)
connector (Note 2)
(insertion type)
Model
Notes: 1
.The wire size shows wiring specification of the connector. Refer to "Selection Example in HIV Wires for Servo Motors" in this catalog for examples of wire size selection.
2.CNP1 and CNP2 connectors, and open tool are supplied with the servo amplifier.
Cautions
3-16
Options/Peripheral Equipment
Details of Optional Cables and Connectors for Servo Amplifiers
Model
CNP1 connector
Open tool
MR-JECNP1-01 (Note 2)
J-FAT-OT
(J.S.T. Mfg. Co., Ltd.)
09JFAT-SAXGDK-H5.0
(J.S.T. Mfg. Co., Ltd.)
Model
CNP1 connector
Open tool
MR-JECNP1-02 (Note 2)
J-FAT-OT-EXL
(J.S.T. Mfg. Co., Ltd.)
07JFAT-SAXGFS-XL
(J.S.T. Mfg. Co., Ltd.)
Model
CNP2 connector
MR-JECNP2-02 (Note 2)
03JFAT-SAXGFK-XL
(J.S.T. Mfg. Co., Ltd.)
Model
Servo amplifier connector
Connector: 10150-3000PE
Shell kit: 10350-52F0-008
(3M)
or an equivalent product
MR-J3CN1
Model
MR-J2M-CN1TBL_M
Junction terminal block connector
Connector: D7950-B500FL
(3M)
Servo amplifier connector
Press bonding type (Note 1)
Connector: 10150-6000EL
Shell kit: 10350-3210-000
(3M)
Notes: 1
.Solder type (connector: 10150-3000PE and shell kit: 10350-52F0-008) (3M) is also usable. Contact the manufacturer directly.
2.CNP1 and CNP2 connectors, and open tool are supplied with the servo amplifier.
3-17
Regenerative Option
MR-RB032
MR-RB12
MR-RB30
MR-RB32
MR-RB50 (Note 1)
40 Ω
40 Ω
13 Ω
40 Ω
13 Ω
30
30
30
30
30
-
100
100
100
100
-
300
300
300
300
-
500
500
Notes: 1
.Be sure to cool the unit forcibly with a cooling fan (92 mm × 92 mm, minimum air flow: 1.0 m3/min). The cooling fan must be prepared by user.
2.The power values in this table are resistor-generated powers, not rated powers.
Servo Motors
MR-JE-10A
MR-JE-20A
MR-JE-40A
MR-JE-70A
MR-JE-100A
MR-JE-200A
MR-JE-300A
Tolerable regenerative power of regenerative option [W] (Note 2)
Servo Amplifiers
Servo amplifier
model
Tolerable
regenerative
power of built-in
regenerative resistor
[W]
10
20
20
100
100
* Cautions when connecting the regenerative option
Options/Peripheral
Equipment
1. The regenerative option causes a temperature rise of 100 °C or higher relative to the ambient temperature. Fully examine heat dissipation, installation position, wires used
before installing the unit. Use flame-retardant wires or apply flame retardant on wires, and keep the wires clear of the unit.
2. Use twisted wires for connecting the regenerative option to the servo amplifier, and keep the wire length to a maximum of 5 m.
3. Use twisted wires for connecting a thermal sensor, and make sure that the sensor does not fail to work properly due to inducted noise.
LVS/Wires
Product List
Cautions
3-18
Options/Peripheral Equipment
Regenerative Option
Dimensions
Connections
[Unit: mm]
MR-RB032
j6 mounting hole
(6)
30
15
(12)
Terminal arrangement
TE1
G3
MR-RB032
144
156
168
G4
P
5
C
Applicable wire size (Note 5):
0.2 mm2 to 2.5 mm2 (AWG 24 to 12)
Mounting screw size: M5
G3
G4
P
C
6
6
12
TE1
(20)
1.6
99
119
Model
MR-RB032
Mass [kg]
0.5
MR-RB12
Terminal arrangement
TE1
G3
(6)
40
36
15
j6 mounting
hole
Disconnect the wires for the built-in
regenerative resistor (P+ and C) and
remove the resistor.
Regenerative option
Servo amplifier
P+
P
C
C
Built-in
regenerative
resistor
(Note 6)
G3
(Note 1)
G4
(Note 4)
5 m or shorter
G4
MR-RBu
P
TE1
144
156
168
C
5
Applicable wire size (Note 5):
0.2 mm2 to 2.5 mm2 (AWG 24 to 12)
Mounting screw size: M5
G3
G4
P
C
Model
MR-RB12
12
6
6
(20)
2
149
169
Mass [kg]
1.1
MR-RB30, MR-RB32
For MR-JE-100A or smaller
142
82.5
P
Terminal arrangement
P
C
30
G4
8.5
10
7
17
90
100
G4
101.5
Terminal screw size: M4
Mounting screw size: M6
82.5
318
335
(30)
Cooling fan intake (Note 3)
Model
MR-RB30
MR-RB32
Mass [kg]
Disconnect the wires for the built-in
regenerative resistor (P+ and C) and
remove the resistor.
Regenerative option
Servo amplifier
G3
G3
C
150
125
8.5
Cooling fan mounting screw (2-M4 screw) (Note 3)
Built-in
regenerative
resistor
2.9
P+
P
C
C
G3
(Note 1)
G4
(Note 4)
5 m or shorter
79
Cooling fan (Note 3)
MR-RB50
For MR-JE-200A or larger
12.5
82.5
350
C
200
217
17
12
(30)
7
120
8
Disconnect P+ and D.
Regenerative option
C
D
G4
Terminal screw size: M4
Mounting screw size: M6
Model
MR-RB50
Servo amplifier
C
G3
Cooling fan intake
162.5
133
2.3
Terminal arrangement
P
162.5
7 × 14
slotted hole
12.5
49
82.5
Cooling fan mounting
screw
(2-M3 screw)
provided on the
opposite side
Mass [kg]
5.6
P
P+
G3
(Note 1)
G4
(Note 4)
5 m or shorter
Cooling fan (Note 2)
Notes: 1
.Create a sequence circuit that turns off the magnetic contactor when abnormal overheating occurs.
2. When using MR-RB50, cool the unit forcibly with a cooling fan (92 mm × 92 mm, minimum air flow: 1.0 m3/min). The cooling fan must be prepared by user.
3.When using MR-RB30 or MR-RB32, it may be necessary to cool the unit forcibly with a cooling fan (92 mm × 92 mm, minimum air flow: 1.0 m3/min), depending on the
operating environment. Refer to "MR-JE-_A Servo Amplifier Instruction Manual" for details. The cooling fan must be prepared by user.
4.G3 and G4 terminals are thermal sensor. G3-G4 opens when the regenerative option overheats abnormally.
5.Refer to "Wires, Molded-Case Circuit Breakers and Magnetic Contactors" in this catalog for examples of wire size selection.
6.MR-JE-10A and MR-JE-20A do not have the built-in regenerative resistor.
3-19
Junction Terminal Block (MR-TB50)
Dimensions
[Unit: mm]
235
Servo Amplifiers
Connect all signals via the junction terminal block.
2-φ4.5
9
50
(25)
50
49
MR-TB50
46.5
2.5
2 4 6 8 10 12 14 16 18 20 2224 26 2830 32 3436 38 40 42 44 4648 50
244
Servo Motors
1 3 5 7 9 11 13 15 17 19 2123 25 2729 31 3335 37 39 41 43 4547 49
25
2
1
Terminal screw size: M3.5
Applicable wire: 2 mm2 maximum
Crimping terminal width: 7.2 mm or shorter
Mounting screw size: M4
Options/Peripheral
Equipment
Radio Noise Filter (FR-BIF)
This filter effectively controls noise emitted from the power supply side of the servo amplifier and is especially effective for radio
frequency bands 10 MHz or lower. The FR-BIF is designed for the input only.
Dimensions
Connections
[Unit: mm]
White
Red Blue Green
j5 hole
MCCB
4
42
29
Leakage current: 4 mA
29
44
58
MC
Terminal block
L1
L2
Power
supply
7
LVS/Wires
Approx. 300
The FR-BIF is designed to be connected with the input only.
Wiring should be as short as possible. Grounding is required.
Be sure to insulate the unused wire when using FR-BIF with 1-phase power.
L3
Servo
amplifier
FR-BIF
This filter is effective in suppressing radio noise emitted from the power supply side or the output side of the servo amplifier, and also in
suppressing high-frequency leakage current (zero-phase current), especially within 0.5 MHz to 5 MHz band.
Dimensions
3
4.5
j3
11.25±0.5
(65)
(65)
(22.5)
2-j5
Use the line noise filter for wires of the power supply (L1, L2, and L3) of the servo amplifier,
and of the motor power (U, V, and W). Pass each of the wires through the line noise filter
equal times in a same direction.
For the power supply, the effect of the filter rises as the number of passes increases, but
generally four passes would be appropriate. For the servo motor power, passes must be four
times or less. Do not pass the grounding wire through the filter. Otherwise, the effect of the
filter is reduced.
Wind the wires to pass through the filter as the required number of passes as shown in
Fig.1. If the wires are too thick to wind, use two or more filters to have the required number
of passes as shown in Fig.2.
Place the line noise filters as close to the servo amplifier as possible for their best
performance.
Fig. 1
Fig. 2
MCCB
MC
Power
supply
Servo amplifier
L1
L2
L3
Line noise filter
Power
supply
MCCB
MC
L1
L2
Servo
amplifier
L3
Line noise filter
Data Line Filter
Surge Killer
Example) E
SD-SR-250 (manufactured by NEC TOKIN Corporation)
ZCAT3035-1330 (manufactured by TDK)
GRFC-13 (manufactured by Kitagawa Industries Co., Ltd.)
Example) Surge killer: CR-50500 (manufactured by Okaya Electric Industries Co., Ltd.)
Diode: A diode with breakdown voltage four or more times greater than the
relay drive voltage, and with current capacity two or more times greater than
the relay drive current.
This filter is effective in preventing noise when attached to the
pulse output cable of the pulse train output controller or the motor
encoder cable.
Attach surge killers to AC relays and AC valves around the servo
amplifier. Attach diodes to DC relays and DC valves.
3-20
Cautions
(110)
95±0.5
Connections
[Unit: mm]
FR-BSF01
Product List
Line Noise Filter (FR-BSF01)
Options/Peripheral Equipment
EMC Filter
The following filters are recommended as a filter compliant with the EMC directive for the power supply of the servo amplifier.
Servo amplifier model
MR-JE-10A to 100A
MR-JE-200A, 300A
EMC filter model
HF3010A-UN (Note 1)
HF3030A-UN (Note 1)
Rated current [A]
10
30
Rated voltage [V AC]
250
250
Fig.
A
B
Notes:1.Manufactured by Soshin Electric Co., Ltd.
A surge protector is separately required to use this EMC filter. Refer to "EMC Installation Guidelines."
Dimensions
HF3010A-UN
110±4
3-M4
32±2
A
M4
4-5.5×7
OUT
(Output side)
85±2
IN
(Input side) 3-M4
Connections
[Unit: mm]
For 3-phase 200 V AC to 240 V AC
258±4
(41)
MCCB
65±4
273±2
Power
supply
288±4
300±5
Leakage
current [mA]
5
Model
HF3010A-UN
EMC filter
OUT
Servo amplifier
MC
1
4
2
5
L2
3
6
L3
L1
E
Mass [kg]
3.5
HF3030A-UN
For 1-phase 200 V AC to 240 V AC
IN
6-R3.25 length 8 OUT
(Input side)
(Output side)
44±1
B
85±1
85±1
210±2
260±5
MCCB
Power
supply
3-M5
125±2
140±1
155±2
3-M5
M4
IN
EMC filter
70±2
140±2
HF3030A-UN
Leakage
current [mA]
5
Mass [kg]
5.5
OUT
Servo amplifier
MC
1
4
2
5
L2
3
6
L3
E
Model
3-21
IN
L1
Power Factor Improving AC Reactor (FR-HAL)
Power factor improving AC
reactor model
Servo amplifier model
FR-HAL-0.4K
Fig.
A
FR-HAL-0.75K
FR-HAL-1.5K
FR-HAL-2.2K
FR-HAL-3.7K
FR-HAL-5.5K
B
Servo Motors
MR-JE-10A
MR-JE-20A
MR-JE-40A
MR-JE-70A
MR-JE-100A
MR-JE-200A
MR-JE-300A
Servo Amplifiers
This boosts the power factor of servo amplifier and reduces the power supply capacity.
Dimensions
Connections
[Unit: mm]
Model
D or shorter
4-d mounting hole (Note 1)
A
Variable dimensions
W1
H
D (Note 3)
D1
D2
d
84
104
104 (Note 2) 84
104 (Note 2) 84
99
99
99
72
74
77
51
56
61
40
44
50
M5
M5
M5
W
(Note 2)
H
Model
Mass [kg]
FR-HAL-0.4K
FR-HAL-0.75K
FR-HAL-1.5K
0.6
0.8
1.1
M4
M4
M4
MCCB
H
W1
7
W or shorter
FR-HAL-2.2K
FR-HAL-3.7K
FR-HAL-5.5K
Model
D2
D1
FR-HAL
Servo amplifier
X
S
Y
T
Z
L1
L2
L3
FR-HAL-2.2K
FR-HAL-3.7K
FR-HAL-5.5K
Variable dimensions
MCCB
W
W1
H
D (Note 3)
D1
D2
d
115 (Note 3)
115 (Note 3)
115 (Note 3)
40
40
40
115
115
115
77
83
83
71
81
81
57
67
67
M6
M6
M6
Mass [kg]
1.5
2.2
2.3
Power
supply
MC
R
FR-HAL
Servo amplifier
X
S
Y
T
Z
L1
L2
Product List
B
R
For 1-phase 200 V AC to 240 V AC
Model
4-d mounting hole (Note 1)
MC
Power
supply
R X S Y T Z
D or shorter
For 3-phase 200 V AC to 240 V AC
Terminal screw size
LVS/Wires
D2
D1
W1
W or shorter
FR-HAL-0.4K
FR-HAL-0.75K
FR-HAL-1.5K
Options/Peripheral
Equipment
R X S Y T Z
L3
Terminal screw size
M4
M4
M4
Cautions
Notes:1.Use this mounting hole for grounding.
2.W ± 2 is applicable for FR-HAL-0.4K to 1.5K.
3.This indicates the maximum dimension. (The dimension varies depending on the bending degree of the Input/Output line.)
3-22
Options/Peripheral Equipment
Servo Support Software
Capacity selection software (MRZJW3-MOTSZ111E)
Specifications
Item
Types of machine component
Item
Output of results
Printing
Data saving
Moment of inertia calculation
function
Description
Horizontal ball screws, vertical ball screws, rack and pinions, roll feeds, rotating tables, carts, elevators,
conveyors, other (direct inertia input) devices
Servo amplifier, servo motor, regenerative option, moment of inertia of load, load to motor inertia ratio,
peak torque, peak torque ratio, effective torque, effective torque ratio, regenerative power, regenerative
power ratio
Prints entered specifications, operating pattern, calculation process, graph of selection process feed
speed (or motor speed) and torque, and sizing results.
Entered specifications, operating patterns and sizing results are saved with a file name.
Cylinder, square block, variable speed, linear movement, hanging, conical, conical base
System requirements
IBM PC/AT compatible model running with the following requirements.
Components
OS (Note 3)
Personal computer (Note 2)
CPU
Memory
Free hard disk space
Communication interface
Browser
Monitor
Keyboard
Mouse
Printer
Communication cable
Capacity selection software (MRZJW3-MOTSZ111E) (Note 1)
Windows 98,
Windows® Me,
Windows® 2000 Professional,
Windows® XP Home Edition/Professional,
Windows Vista® Home Basic/Home Premium/Business/Ultimate/Enterprise,
Windows® 7 Starter/Home Premium/Professional/Ultimate/Enterprise
Pentium® 133 MHz or more
(Windows® 98, Windows® 2000 Professional)
®
Pentium 150 MHz or more
(Windows® Me)
Pentium® 300 MHz or more
(Windows® XP Home Edition/Professional)
1 GHz or more 32-bit (×86) processor
(Windows Vista® Home Basic/Home Premium/
Business/Ultimate/Enterprise)
1 GHz or more 32-bit (×86) or 64-bit (×64) processor (Windows® 7 Starter/Home Premium/Professional/
Ultimate/Enterprise)
24 MB or more
(Windows® 98)
32 MB or more
(Windows® Me, Windows® 2000 Professional)
128 MB or more (Windows® XP Home Edition/Professional)
512 MB or more (Windows Vista® Home Basic)
1 GB or more
(Windows Vista® Home Premium/Business/Ultimate/Enterprise,
Windows® 7 Starter/Home Premium/Professional/Ultimate/Enterprise)
40 MB or more
Windows® Internet Explorer® 4.0 or later
Resolution 800 × 600 or more, 16-bit high color,
Compatible with above personal computers.
Compatible with above personal computers.
Compatible with above personal computers.
Compatible with above personal computers.
Not required
®
Notes:1.Software version C6 or later will be compatible with MR-JE series.
2.This software may not run correctly, depending on a personal computer being used.
3.For 64-bit operating system, this software is compatible with Windows® 7.
3-23
Servo Amplifiers
Servo Support Software
MR Configurator2 (SW1DNC-MRC2-E)
MR Configurator2 can be obtained by either of the following:
•Purchase MR Configurator2 alone.
•Purchase MT Works2: MR Configurator2 is included in MT Works2 with software version 1.34L or later.
•Download MR Configurator2: If you have GX Works2 or MT Works2 with software version earlier than 1.34L, you can download
MR Configurator2 from website free of charge.
Specifications
Diagnosis
Adjustment
Others
Options/Peripheral
Equipment
Test mode
Description
Create/read/save/delete project, system setting, print
Parameter setting, axis name setting, parameter converter
Display all, I/O monitor, graph
Alarm display, alarm onset data, drive recorder, no motor rotation, system configuration, life diagnosis,
machine diagnosis
JOG mode, positioning mode, motor-less operation, DO forced output, program operation, test mode
information
One-touch tuning, tuning, machine analyzer
Servo assistant, parameter setting range update, help display
Servo Motors
Item
Project
Parameter
Monitor
LVS/Wires
System requirements
Components
CPU (recommended)
Memory (recommended)
Free hard disk space
Communication interface
Browser
Monitor
Keyboard
Mouse
Printer
Communication cable
MR Configurator2 (Note 3)
Windows 2000 Professional,
Windows® XP Home Edition/Professional,
Windows Vista® Home Basic/Home Premium/Business/Ultimate/Enterprise,
Windows® 7 Starter/Home Premium/Professional/Ultimate/Enterprise
Desktop PC: Intel® Celeron® processor 2.8 GHz or more
Laptop PC: Intel® Pentium® M processor 1.7 GHz or more
512 MB or more (32-bit OS), 1 GB or more (64-bit OS)
1 GB or more
Use USB port
Windows® Internet Explorer® 4.0 or later
Resolution 1024 × 768 or more, 16-bit high color,
Compatible with above personal computers.
Compatible with above personal computers.
Compatible with above personal computers.
Compatible with above personal computers.
MR-J3USBCBL3M
®
Cautions
Personal computer (Note 1)
OS (Note 2)
Product List
IBM PC/AT compatible model running with the following requirements.
Notes:1.This software may not run correctly, depending on a personal computer being used.
2.For 64-bit operating system, this software is compatible with Windows® 7.
3.Software version 1.19V or later is compatible with MR-JE series.
3-24
MEMO
4
Features of Low-Voltage Switchgear........................................................ 4-1
Wires, Molded-Case Circuit Breakers and Magnetic Contactors............. 4-4
Selection Example in HIV Wires for Servo Motors....................................... 4-4
Low-Voltage Switchgear/Wires
Low-Voltage Switchgear/Wires
Mitsubishi Molded Case Circuit Breakers and Earth Leakage Circuit Breakers
WS-V Series
"WS-V Series" is the new circuit breakers that have a lot of superior aspects such as higher breaking
capacity, design for easy use, standardization of accessory parts, and compliance to the global
standards.
Features
Technologies based on long years of experience are brought together to
achieve improved performance
The new circuit breaking technology "Expanded ISTAC" has improved the currentlimiting performance and upgraded the overall breaking capacity.
Expansion of the conductor under the stator shortens the contact parting time of the
mover as compared to the conventional ISTAC structure.
The current-limiting performance has been improved remarkably. (The maximum
peak current value has been reduced by approx. 10%.)
New circuit breaking technology (Expanded ISTAC)
Grid
Current C
Compact design for ease of use
The thermal adjustable circuit breakers and electronic circuit breakers are smaller.
NF250-SGV
(Compared with our conventional models)
(New model:
105 ✕ 165 ✕ 68 mm)
Types of internal accessories are reduced from 3 types to 1 type
Standardization of internal accessories contributes to a reduction of stock and
delivery time.
Conventional models
Reaction circuit
Fixed conductor
Current B
Volume ratio 79%
(Conventional model:
105 ✕ 165 ✕ 86 mm)
Current
Increased reaction force of
movable conductor
For 32/63AF
Three types
■ Breaking capacity comparison with a conventional model
20 %
UP
250-RG
Model Name
NF250-SGW
Arc
Movable conductor
50 %
UP
250-H
20 %
UP
250-S
WS-V Series
WS Series
38.8%
UP
250-C
20 %
UP
125-RG
20
40
60
80
100
kA at 400 V AC lcu
120
140
160
For 125AF
For 250AF
New models
For 32 to 250AF
One type
Applicable accessories
AL
AX
AL+AX
SHT
UVT
Style
Lineup of UL 489 listed circuit breakers with 54 mm width "Small Fit"
The compact breakers contribute to a size reduction of machines, and IEC 35 mm rail mounting is standard.
NF50-SVFU
NF100-CVFU
NV50-SVFU
NV100-CVFU
For security and standard compliance of machines, F-type and V-type
operating handles are available for breakers with 54 mm width.
Lineup of UL 489 listed circuit breakers for 480 V AC "High Performance"
The breaking capacity has been improved to satisfy the request for SCCR upgrading.
NF125-SVU
4-1
NF125-HVU
NF250-SVU
NF250-HVU
Breaking capacity of UL 489 listed circuit breakers for 480 V AC
(UL 489)
NF125-SVU/NV125-SVU:30 kA
NF125-HVU/NV125-HVU:50 kA
NF250-SVU/NV250-SVU:35 kA
NF250-HVU/NV250-HVU:50 kA
Mitsubishi Magnetic Motor Starters and Magnetic Contactors MS-T Series
Servo Amplifiers
MS-T series is newly released!
The MS-T series is smaller than ever, enabling more compact control panel. The MS-T series is suitable for
MELSERVO-JE series as well as other Mitsubishi FA equipment. In addition, the MS-T conforms to a variety
of global standards, supporting the global use.
Features
Compact
S-T10
*Based on Mitsubishi Electric research as of September 2012 in the general-purpose magnetic contactor industry for 10 A-frame class.
Frame size
11 A
13 A
43
Front view
1/L1
3/L2
5/L3
13
1/L1
3/L2
13
13
1/L1
3/L2
5/L3
13
21
1/L1
3/L2
5/L3
21
1/L1
3/L2
5/L3
2/T1
4/T2
6/T3
13
21
43
31
22
14
2/T1
4/T2
6/T3
14
2/T1
S-N10
4/T2
Front view
6/T3
14
14
S-N11 (Auxiliary 1-pole)
2/T1
4/T2
6/T3
14
22
S-N12 (Auxiliary 2-pole)
43
36
New
MS-T series
5/L3
75
63
53
43
[Unit: mm]
25 A
m!
2/T1
4/T2
6/T3
S-N25
43
63
-10 m
-20
S-T12 (Auxiliary 2-pole)
m!
!
mm
-12 m
S-T20
S-T25
LVS/Wires
S-T10
32
44
S-N20
m!
-7 m
22
Options/Peripheral
Equipment
MS-N series
20 A
Servo Motors
Just 36 mm wide for 10 A-frame type!
General-purpose magnetic contactor with smallest width* in the industry.
The width of MS-T series is reduced by 32% as compared to the prior MS-N series, enabling a more compact panel.
Standardization
Covers provided as standard equipment
Terminal cover and auxiliary contact unit covers are provided as standard
equipment. Not only ensuring your safety, but also saving you time and cost of
selecting and purchasing the covers separately.
rs are
Cove ed as
attachdard.
stan
Covers + Contactor
Coil designation
Coil designation
AC24 V
AC48 V
AC100 V
AC200 V
AC300 V
AC400 V
AC500 V
Rated voltage [V]
50 Hz/60 Hz
24
48 to 50
100 to 127
200 to 240
260 to 300
380 to 440
460 to 550
Cautions
AC12 V
AC24 V
AC48 V
AC100 V
AC120 V
AC127 V
AC200 V
AC220 V
AC230 V
AC260 V
AC380 V
AC400 V
AC440 V
AC500 V
Rated voltage [V]
50 Hz
60 Hz
12
12
24
24
48 to 50
48 to 50
100
100 to 110
110 to 120
115 to 120
125 to 127
127
200
200 to 220
208 to 220
220
220 to 240
230 to 240
240 to 260
260 to 280
346 to 380
380
380 to 415
400 to 440
415 to 440
460 to 480
500
500 to 550
* 12 V type is an order-made product.
Global Standard
Conforms to various global standards
Not only major global standards such as IEC, JIS, UL, CE, and CCC but also ship standards and other country standards are planned
to be certified.
Model
S-T10 to S-T32
MSO-T10 to MSO-T25
TH-T18(KP) to TH-T25(KP)
IEC
International
Applicable Standard
JIS
DIN/VDE
Japan
Germany
BS/EN
England
Europe
Safety Standard
UL
CSA
U.S.A
Canada
Product List
Wide-ranged operation coil rating
The prior series had 14 types of the operation coil rating. Owing to the wide-ranged operation coil rating, the number of
the rating types for the MS-T series is reduced to half, making it easier to select as compared to the prior model.
Consolidating the number of the produced coils type allows not just the reduction of customer storage, but also shortening of delivery time.
: Compliant as standard
EC Directive
CE Marking
Certification Body
TÜV
CCC
GB
Europe
Germany
China
*1, 2
*1
*1.CCC and TÜV approval will be obtained soon.
*2.The Motor Starters will be certified under each type name of the Magnetic contactors and the Thermal Overload Relays on the condition that the Magnetic contactors and
the Thermal Overload Relays are used in combination.
4-2
Low-Voltage Switchgear/Wires
Mitsubishi Magnetic Motor Starters and Magnetic Contactors MS-N Series
Environment-friendly Mitsubishi MS-N series ensures safety and conforms to various global standards. Its
compact size contributes to space-saving in a machine. The MS-N series is suitable for MELSERVO-JE series as
well as other Mitsubishi FA equipment and can be used globally.
Features
Bifurcated contact adopted to achieve high contact reliability
Contact reliability is greatly improved by combining bifurcated moving contact and stationary contact.
This series responds to the various needs such as the application to safety circuit.
S-N35CX
* The MS-T series also has bifurcated contacts.
Mirror contact (auxiliary contact off at main contact welding)
The MS-N series meets requirements of "Control functions in the event of failure" described in
EN 60204-1 "Electrical equipment of machines", being suitable as interlock circuit contact. The MS-N
series is applicable for category 4 safety circuit. We ensure safety for our customers.
* The MS-T series also has mirror contacts.
Main contact welding
Various option units
Various options including surge absorbers and additional auxiliary contact blocks are available.
Gap
Conforms to various global standards
Model
S-N10 to S-N400
MSO-N10 to MSO-N400
TH-N12KP to TH-N400KP
IEC
International
Applicable Standard
JIS
DIN/VDE
Japan
Germany
BS/EN
England
Europe
Safety Standard
UL
CSA
U.S.A
Canada
Auxiliary
normally
closed
contact
: Compliant as standard
EC Directive
CE Marking
Certification Body
TÜV
CCC
GB
Europe
Germany
China
*1
*1.The Motor Starters are certified under each type name of the Magnetic contactors and the Thermal Overload Relays on the condition that the Magnetic contactors and the
Thermal Overload Relays are used in combination.
4-3
Wires, Molded-Case Circuit Breakers and Magnetic Contactors
Servo amplifier model
Molded-case circuit
breaker (Note 4)
MR-JE-20A
30 A frame 5 A
MR-JE-40A
30 A frame 10 A
MR-JE-70A
30 A frame 15 A
MR-JE-100A
30 A frame 15 A
MR-JE-200A
30 A frame 20 A
MR-JE-300A
30 A frame 30 A
S-N10
S-T10
S-N10
S-T10
S-N10
S-T10
S-N10
S-T10
S-N10
S-T10
S-N20 (Note 5)
S-T21
S-N20
S-T21
2 (AWG 14) (Note 1)
3.5 (AWG 12)
Wire size [mm2]
P+, C
U, V, W,
AWG 18 to 14 (Note 3)
2 (AWG 14) (Note 1)
AWG 16 to 10 (Note 3)
Notes:1.Keep the wire length to the regenerative option within 5 m.
2.Be sure to use a magnetic contactor with an operation delay time of 80 ms or less. The operation delay time is the time interval from current being applied to the coil until
closure of contacts.
3.The wire size shows applicable size for the servo amplifier connector.
4.When complying with UL/CSA standard, refer to "MELSERVO-JE Instructions and Cautions for Safe Use of AC Servos" enclosed with the servo amplifier.
5.S-N18 can be used when auxiliary contact is not required.
The following are examples of wire sizes when 600 V grade heat-resistant polyvinyl chloride insulated wires (HIV wires) with a length of
30 m are used. Refer to "HF-KN HF-SN Servo Motor Instruction Manual" when using cab-tire cables for supplying power (U, V, and W) to
HF-SN series.
Servo motor
Product List
HF-KN13(B)J, 23(B)J, 43(B)J, 73(B)J
HF-SN52(B)J, 102(B)J
HF-SN152(B)J, 202(B)J
HF-SN302(B)J
Wire size [mm2]
For power and grounding
For electromagnetic brake (B1, B2)
(U, V, W, ) (general environment)
0.75 (AWG 18) (Note 1, 2, 3)
0.5 (AWG 20) (Note 4)
1.25 (AWG 16) (Note 5)
2 (AWG 14)
1.25 (AWG 16)
3.5 (AWG 12)
LVS/Wires
Selection Example in HIV Wires for Servo Motors
Options/Peripheral
Equipment
30 A frame 5 A
L1, L2, L3,
(Note 2)
Servo Motors
MR-JE-10A
Magnetic contactor
Servo Amplifiers
The following are examples of wire sizes when 600 V grade heat-resistant polyvinyl chloride insulated wires (HIV wires) are used.
The wire size for U, V, W, and varies depending on the servo motor. Refer to "Selection Example in HIV Wires for Servo Motors" in
this catalog for details on wires for each servo motor.
Notes:1.Use a fluorine resin wire of 0.75 mm2 (AWG 18) for wiring to the servo motor power connector.
2.This size is applicable for wiring length of 10 m or shorter. For over 10 m, use MR-PWS2CBL03M-A_-L and extend it with HIV wire of 1.25 mm2 (AWG 16).
3.When complying with UL/CSA standard, extend the wire using MR-PWS2CBL03M-A_-L and HIV wire of 2 mm2 (AWG 14).
4.Use a fluorine resin wire of 0.5 mm2 (AWG 20) when connecting to servo motor electromagnetic brake connector.
5.When complying with UL/CSA standard, use 2 mm2 (AWG 14). Refer to "HF-KN HF-SN Servo Motor Instruction Manual" for details.
Cautions
4-4
Servo amplifiers
Item
MR-JE-A
Model
Rated output
Power supply
MR-JE-10A
0.1 kW
3-phase or 1-phase 200 V AC to 240 V AC
MR-JE-20A
0.2 kW
3-phase or 1-phase 200 V AC to 240 V AC
MR-JE-40A
0.4 kW
3-phase or 1-phase 200 V AC to 240 V AC
MR-JE-70A
0.75 kW
3-phase or 1-phase 200 V AC to 240 V AC
MR-JE-100A
1 kW
3-phase 200 V AC to 240 V AC
MR-JE-200A
2 kW
3-phase 200 V AC to 240 V AC
MR-JE-300A
3 kW
3-phase 200 V AC to 240 V AC
Servo motors
Item
HF-KN series
Without electromagnetic brake
With oil seal
HF-KN series
Without electromagnetic brake
Without oil seal
HF-KN series
With electromagnetic brake
With oil seal
HF-KN series
With electromagnetic brake
Without oil seal
HF-SN series
Without electromagnetic brake
With oil seal
HF-SN series
With electromagnetic brake
With oil seal
Model
Rated output
Rated speed
HF-KN13J
100 W
3000 r/min
HF-KN23J
200 W
3000 r/min
HF-KN43J
400 W
3000 r/min
HF-KN73J
750 W
3000 r/min
HF-KN13
100 W
3000 r/min
HF-KN23
200 W
3000 r/min
HF-KN43
400 W
3000 r/min
HF-KN13BJ
100 W
3000 r/min
HF-KN23BJ
200 W
3000 r/min
HF-KN43BJ
400 W
3000 r/min
HF-KN73BJ
750 W
3000 r/min
HF-KN13B
100 W
3000 r/min
HF-KN23B
200 W
3000 r/min
HF-KN43B
400 W
3000 r/min
HF-SN52J
0.5 kW
2000 r/min
HF-SN102J
1.0 kW
2000 r/min
HF-SN152J
1.5 kW
2000 r/min
HF-SN202J
2.0 kW
2000 r/min
HF-SN302J
3.0 kW
2000 r/min
HF-SN52BJ
0.5 kW
2000 r/min
HF-SN102BJ
1.0 kW
2000 r/min
HF-SN152BJ
1.5 kW
2000 r/min
HF-SN202BJ
2.0 kW
2000 r/min
HF-SN302BJ
3.0 kW
2000 r/min
Encoder cables/Junction cables
Item
Encoder cable
(load-side lead)
Model
Length
Bending life
Long bending life
IP
Application
rating
IP65
For HF-KN (direct connection type)
MR-J3ENCBL2M-A1-H
2m
MR-J3ENCBL5M-A1-H
5m
Long bending life
IP65
For HF-KN (direct connection type)
MR-J3ENCBL10M-A1-H
10 m
Long bending life
IP65
For HF-KN (direct connection type)
For HF-KN (direct connection type)
MR-J3ENCBL2M-A1-L
2m
Standard
IP65
MR-J3ENCBL5M-A1-L
5m
Standard
IP65
For HF-KN (direct connection type)
MR-J3ENCBL10M-A1-L
10 m
Standard
IP65
For HF-KN (direct connection type)
MR-J3ENCBL2M-A2-H
2m
Long bending life
IP65
For HF-KN (direct connection type)
MR-J3ENCBL5M-A2-H
5m
Long bending life
IP65
For HF-KN (direct connection type)
MR-J3ENCBL10M-A2-H
10 m
Long bending life
IP65
For HF-KN (direct connection type)
MR-J3ENCBL2M-A2-L
2m
Standard
IP65
For HF-KN (direct connection type)
MR-J3ENCBL5M-A2-L
5m
Standard
IP65
For HF-KN (direct connection type)
MR-J3ENCBL10M-A2-L
10 m
Standard
IP65
For HF-KN (direct connection type)
Encoder cable
(load-side lead)
MR-J3JCBL03M-A1-L
0.3 m
Standard
IP20
For HF-KN (junction type) (Note 1)
Encoder cable
(opposite to load-side lead)
MR-J3JCBL03M-A2-L
0.3 m
Standard
IP20
For HF-KN (junction type) (Note 1)
Encoder cable
(opposite to load-side lead)
MR-EKCBL20M-H
20 m
Long bending life
IP20
For HF-KN (junction type) (Note 2)
MR-EKCBL30M-H
30 m
Long bending life
IP20
For HF-KN (junction type) (Note 2)
MR-EKCBL40M-H
40 m
Long bending life
IP20
For HF-KN (junction type) (Note 2)
MR-EKCBL50M-H
50 m
Long bending life
IP20
For HF-KN (junction type) (Note 2)
MR-EKCBL20M-L
20 m
Standard
IP20
For HF-KN (junction type) (Note 2)
MR-EKCBL30M-L
30 m
Standard
IP20
For HF-KN (junction type) (Note 2)
Encoder cable
(load-side lead)
MR-J3JSCBL03M-A1-L
0.3 m
Standard
IP65
For HF-KN (junction type) (Note 3)
Encoder cable
(opposite to load-side lead)
MR-J3JSCBL03M-A2-L
0.3 m
Standard
IP65
For HF-KN (junction type) (Note 3)
MR-J3ENSCBL2M-H
2m
Long bending life
IP67
MR-J3ENSCBL5M-H
5m
Long bending life
IP67
MR-J3ENSCBL10M-H
10 m
Long bending life
IP67
MR-J3ENSCBL20M-H
20 m
Long bending life
IP67
MR-J3ENSCBL30M-H
30 m
Long bending life
IP67
MR-J3ENSCBL40M-H
40 m
Long bending life
IP67
MR-J3ENSCBL50M-H
50 m
Long bending life
IP67
MR-J3ENSCBL2M-L
2m
Standard
IP67
MR-J3ENSCBL5M-L
5m
Standard
IP67
MR-J3ENSCBL10M-L
10 m
Standard
IP67
MR-J3ENSCBL20M-L
20 m
Standard
IP67
MR-J3ENSCBL30M-L
30 m
Standard
IP67
Encoder cable
Encoder cable
For HF-KN (junction type) (Note 4),
For HF-SN (direct connection type)
For HF-KN (junction type) (Note 4),
For HF-SN (direct connection type)
Encoder connector sets/Junction connector sets
Item
Model
Description
IP
rating
Application
MR-ECNM
Junction connector × 1,
Servo amplifier connector × 1
IP20
For HF-KN (junction type) (Note 2)
Encoder connector set
(one-touch connection type)
MR-J3SCNS
Straight type
Junction connector or encoder
connector × 1,
Servo amplifier connector × 1
IP67
For HF-KN (junction type) (Note 4),
For HF-SN (direct connection type)
Encoder connector set
(one-touch connection type)
MR-J3SCNSA
Angle type
Encoder connector × 1,
Servo amplifier connector × 1
IP67
For HF-SN
Encoder connector set
Notes:
1. Use this in combination with MR-EKCBL_M-H, MR-EKCBL_M-L, or MR-ECNM.
2. Use this in combination with MR-J3JCBL03M-A1-L or MR-J3JCBL03M-A2-L.
3. Use this in combination with MR-J3ENSCBL_M-H, MR-J3ENSCBL_M-L, or MR-J3SCNS.
4. Use this in combination with MR-J3JSCBL03M-A1-L or MR-J3JSCBL03M-A2-L when using for HF-KN series.
Servo motor power cables
Item
Servo motor power cable
(load-side lead, lead-out)
Model
Length
Bending life
Long bending life
IP
Application
rating
IP65
For HF-KN (direct connection type)
MR-PWS1CBL2M-A1-H
2m
MR-PWS1CBL5M-A1-H
5m
Long bending life
IP65
For HF-KN (direct connection type)
MR-PWS1CBL10M-A1-H
10 m
Long bending life
IP65
For HF-KN (direct connection type)
MR-PWS1CBL2M-A1-L
2m
Standard
IP65
For HF-KN (direct connection type)
MR-PWS1CBL5M-A1-L
5m
Standard
IP65
For HF-KN (direct connection type)
MR-PWS1CBL10M-A1-L
10 m
Standard
IP65
For HF-KN (direct connection type)
MR-PWS1CBL2M-A2-H
2m
Long bending life
IP65
For HF-KN (direct connection type)
MR-PWS1CBL5M-A2-H
5m
Long bending life
IP65
For HF-KN (direct connection type)
MR-PWS1CBL10M-A2-H
10 m
Long bending life
IP65
For HF-KN (direct connection type)
MR-PWS1CBL2M-A2-L
2m
Standard
IP65
For HF-KN (direct connection type)
MR-PWS1CBL5M-A2-L
5m
Standard
IP65
For HF-KN (direct connection type)
MR-PWS1CBL10M-A2-L
10 m
Standard
IP65
For HF-KN (direct connection type)
Servo motor power cable
(load-side lead, lead-out)
MR-PWS2CBL03M-A1-L
0.3 m
Standard
IP55
For HF-KN (junction type)
Servo motor power cable
(opposite to load-side lead,
lead-out)
MR-PWS2CBL03M-A2-L
0.3 m
Standard
IP55
For HF-KN (junction type)
Servo motor power cable
(opposite to load-side lead,
lead-out)
Servo motor power connector sets
Item
Servo motor power connector set
EN compliant
Description
Model
IP
rating
Application
MR-PWCNS4
Straight type
Power connector × 1
IP67
For HF-SN52J, 102J, 152J
MR-PWCNS5
Straight type
Power connector × 1
IP67
For HF-SN202J, 302J
Electromagnetic brake cables
Item
Electromagnetic brake cable
(load-side lead, lead-out)
Model
Length
Bending life
Long bending life
IP
Application
rating
IP65
For HF-KN (direct connection type)
MR-BKS1CBL2M-A1-H
2m
MR-BKS1CBL5M-A1-H
5m
Long bending life
IP65
For HF-KN (direct connection type)
MR-BKS1CBL10M-A1-H
10 m
Long bending life
IP65
For HF-KN (direct connection type)
MR-BKS1CBL2M-A1-L
2m
Standard
IP65
For HF-KN (direct connection type)
MR-BKS1CBL5M-A1-L
5m
Standard
IP65
For HF-KN (direct connection type)
MR-BKS1CBL10M-A1-L
10 m
Standard
IP65
For HF-KN (direct connection type)
MR-BKS1CBL2M-A2-H
2m
Long bending life
IP65
For HF-KN (direct connection type)
MR-BKS1CBL5M-A2-H
5m
Long bending life
IP65
For HF-KN (direct connection type)
MR-BKS1CBL10M-A2-H
10 m
Long bending life
IP65
For HF-KN (direct connection type)
MR-BKS1CBL2M-A2-L
2m
Standard
IP65
For HF-KN (direct connection type)
MR-BKS1CBL5M-A2-L
5m
Standard
IP65
For HF-KN (direct connection type)
MR-BKS1CBL10M-A2-L
10 m
Standard
IP65
For HF-KN (direct connection type)
Electromagnetic brake cable
(load-side lead, lead-out)
MR-BKS2CBL03M-A1-L
0.3 m
Standard
IP55
For HF-KN (junction type)
Electromagnetic brake cable
(opposite to load-side lead,
lead-out)
MR-BKS2CBL03M-A2-L
0.3 m
Standard
IP55
For HF-KN (junction type)
Electromagnetic brake cable
(opposite to load-side lead,
lead-out)
Electromagnetic brake connector sets
Item
Model
Description
IP
rating
Application
Electromagnetic brake connector
MR-BKCNS1
set (one-touch connection type)
Straight type, Electromagnetic
brake connector × 1
IP67
For HF-SN
Electromagnetic brake connector
MR-BKCNS1A
set (one-touch connection type)
Angle type, Electromagnetic
brake connector × 1
IP67
For HF-SN
Junction terminal blocks/Junction terminal block cables
Item
Model
Application
Length
Junction terminal block (50 pins)
MR-TB50
-
For MR-JE-A
Junction terminal block cable
(for MR-TB50)
MR-J2M-CN1TBL05M
0.5 m
For connecting MR-JE-A and MR-TB50
MR-J2M-CN1TBL1M
1m
For connecting MR-JE-A and MR-TB50
Regenerative Options
Item
Regenerative option
Specifications
Model
Application
MR-RB032
Tolerable regenerative power: 30 W,
resistance value: 40 Ω
For MR-JE-10A to MR-JE-100A
MR-RB12
Tolerable regenerative power: 100 W,
resistance value: 40 Ω
For MR-JE-20A to MR-JE-100A
MR-RB30
Tolerable regenerative power: 300 W,
resistance value: 13 Ω
For MR-JE-200A and MR-JE-300A
MR-RB32
Tolerable regenerative power: 300 W,
resistance value: 40 Ω
For MR-JE-70A and MR-JE-100A
MR-RB50
Tolerable regenerative power: 500 W,
resistance value: 13 Ω
For MR-JE-200A and MR-JE-300A
Peripheral cables
Item
Personal computer
communication cable
(USB cable)
Model
MR-J3USBCBL3M
Application
Length
3m
For MR-JE-A
Peripheral connectors
Item
Model
Description
Application
Servo amplifier CNP1
power connector (Note 1)
(insertion type)
MR-JECNP1-01
CNP1 connector × 1, Open tool × 1
For MR-JE-10A to MR-JE-100A
Servo amplifier CNP1
power connector (Note 1)
(insertion type)
MR-JECNP1-02
CNP1 connector × 1, Open tool × 1
For MR-JE-200A and MR-JE-300A
Servo amplifier CNP2
power connector (Note 1)
(insertion type)
MR-JECNP2-02
CNP2 connector × 1
For MR-JE-200A and MR-JE-300A
Connector set
MR-J3CN1
Servo amplifier connector × 1
For I/O signals of MR-JE-A
Servo Support Software
Item
MR Configurator2
Application
Model
SW1DNC-MRC2-E
Servo setup software for AC servo
Notes:
1. CNP1 and CNP2 connectors, and open tool are supplied with the servo amplifier.
Cautions
To ensure safe use
●●To use the products given in this catalog properly, always read the
"Installation Guide" and "Instruction Manual" before starting to use them.
Cautions for model selection
●●Select a servo motor which has the rated torque equal to or higher than
the continuous effective torque.
●●When unbalanced torque is generated, such as in a vertical lift machine,
it is recommended that the unbalanced torque of the machine be kept
under 70% of the servo motor rated torque.
●●Create the operating pattern by considering the settling time (ts).
●●Load to motor inertia ratio
must be below the
Speed
Command pattern
recommended ratio. If the
Actual servo motor
ratio is too large, the
operation
expected performance may
not be achieved, and the
Time
ts
Command time
dynamic brake may be
Positioning time
damaged.
General safety precautions
1. Transportation/installation
●●Combinations of the servo motor and the servo amplifier are
predetermined. Confirm the models of the servo motor and the servo
amplifier to be used before installation.
●●Do not drop or apply strong impact on the servo amplifier and the servo
motor as they are precision devices. They may be damaged from such
stress or shock.
●●When you disinfect or protect wooden packing from insects, take
measures except by fumigation. Fumigating the servo amplifier or
packing the servo amplifier with fumigated wooden packing can cause a
malfunction of the servo amplifier due to halogen materials (such as
fluorine, chlorine, bromine, and iodine) which are contained in fumigant.
●●Do not get on or place heavy objects on the servo amplifier or the servo
motor. Doing so may result in injury or damage.
●●The system must withstand high speeds and high acceleration/
deceleration.
●●To enable high-accuracy positioning, ensure the machine rigidity, and
keep the machine resonance point at a high level.
●●Mount the servo amplifier and the servo motor on nonflammable
material. Mounting them directly on or near flammable material may
result in fires.
●●The regenerative option becomes hot (the temperature rise of 100 °C
or higher) with frequent use. Do not install within flammable objects or
objects subject to thermal deformation. Make sure that wires do not
come into contact with the unit.
●●Securely fix the servo motor onto the machine. Insufficient fixing may
cause the servo motor to dislocate during operation.
●●Install electrical and mechanical stoppers at the stroke end.
●●Mount the servo amplifier vertically on a wall.
●●Do not block intake and exhaust areas of the servo amplifier. Doing so
may cause the servo amplifier to malfunction.
●●When installing multiple servo amplifiers in a row in a sealed cabinet,
leave space around the servo amplifiers as described in Servo Amplifier
Instruction Manual. To ensure the life and reliability of the servo
amplifiers, prevent heat accumulation by keeping space as open as
possible toward the top plate.
2. Environment
●●Use the servo amplifier and the servo motor in the designated
environment.
●●Avoid installing the servo amplifier and the servo motor in areas with oil
mist or dust. When installing in such areas, be sure to enclose the servo
6-1
amplifier in a sealed cabinet, and protect the servo motor by furnishing
a cover or by taking similar measures.
●●Do not use in areas where the servo motor may be constantly subject
to cutting fluid or lubricant oil, or where dew could condense because of
oil mist, overcooling or excessive humidity. Doing so may deteriorate
the insulation of the servo motor.
●●The servo amplifier must not be used with parts which contain halogenseries flame retardant materials (such as bromine) under coexisting
conditions.
3. Grounding
●●Securely ground to prevent electric shocks and to stabilize the potential
in the control circuit.
●●Connect the grounding wire to the cabinet protective earth (PE) terminal
via the servo amplifier protective earth (PE) terminal for the servo motor
grounding.
●●Faults such as a position mismatch may occur if the grounding is
insufficient.
4. Wiring
●●Do not supply power to the output terminals (U, V, and W) of the servo
amplifier or the input terminals (U, V, and W) of the servo motor. Doing
so damages the servo amplifier and the servo motor.
●●Connect the servo motor to the output terminals (U, V, and W) of the
servo amplifier.
●●Match the phase of the input terminals (U, V, and W) of the servo motor
to the output terminals (U, V, and W) of the servo amplifier when
connecting them. If they do not match, the servo motor does not
operate properly.
●●Check the wiring and sequence program thoroughly before switching
the power on.
●●Carefully select the cable clamping method, and make sure that
bending stress and the stress of the cable's own weight are not applied
on the cable connection section.
●●In an application where the servo motor moves, determine the cable
bending radius according to the cable bending life and wire type.
5. Factory settings
●●Select a control mode from position, speed or torque by [Pr. PA01].
Position control mode is set as default. Change the parameter setting
value when using the other control modes.
●●When using the regenerative option, change [Pr. PA02]. The
regenerative option is disabled as default.
6. Operation
●●Do not use a product which is damaged or has missing parts. In that
case, replace the product.
●●Turn on FLS and RLS (Upper/Lower stroke limit), or LSP and LSN
(Forward/Reverse rotation stroke end) in position or speed control mode.
The servo motor will not start if the signals are off.
●●When a magnetic contactor is installed on the primary side of the servo
amplifier, do not perform frequent starts and stops with the magnetic
contactor. Doing so may damage the servo amplifier.
●●When an error occurs, the servo amplifier stops outputting the power
with activation of the protective function, and the servo motor stops
immediately with the dynamic brake.
●●The dynamic brake is a function for emergency stop. Do not use it to
stop the servo motor in normal operations.
●●As a rough guide, the dynamic brake withstands 1000 times of use
when a machine which has load to motor inertia ratio equals to or lower
than the recommended ratio stops from the rated speed every 10
minutes.
●●If the protective functions of the servo amplifier activate, turn the power
off immediately. Remove the cause before turning the power on again. If
operation is continued without removing the cause of the error, the
servo motor may malfunction, resulting in injury or damage.
●●The servo amplifier, the regenerative resistor, and the servo motor can
Servo Amplifiers
be very hot during or after operation. Take safety measures such as
covering them to prevent your hand and/or parts including cables from
coming in contact with them.
7. Others
●●Do not touch the servo amplifier or the servo motor with wet hands.
●●Do not modify the servo amplifier or the servo motor.
Cautions for servo motors
Servo Motors
●●Do not hammer the shaft of the servo motor when installing a pulley or
Options/Peripheral
Equipment
a coupling. Doing so may damage the encoder. When installing the
pulley or the coupling to the key shaft servo motor, use the screw hole
on the shaft end. Use a pulley extractor when removing the pulley.
●●Do not apply a load exceeding the tolerable load onto the servo motor
shaft. The shaft may break.
●●When the servo motor is mounted with the shaft vertical (shaft up), take
measures on the machine side so that oil from the gear box does not
get into the servo motor.
●●Do not use the 24 V DC interface power supply for the electromagnetic
brake. Provide a dedicated power supply to the electromagnetic brake.
●●Do not apply the electromagnetic brake when the servo is on. Doing so
may cause the servo amplifier overload or shorten the brake life. Apply
the electromagnetic brake when the servo is off.
●●Torque may drop due to temperature increase of the servo motor. Be
LVS/Wires
sure to use the motor within the specified ambient temperature.
Product List
Cautions
6-2
Cautions
Warranty
1. Warranty period and coverage
We will repair any failure or defect hereinafter referred to as “failure” in our
FA equipment hereinafter referred to as the “Product” arisen during warranty
period at no charge due to causes for which we are responsible through the
distributor from which you purchased the Product or our service provider.
However, we will charge the actual cost of dispatching our engineer for an
on-site repair work on request by customer in Japan or overseas countries.
We are not responsible for any on-site readjustment and/or trial run that may
be required after a defective unit is repaired or replaced.
[Term]
The term of warranty for Product is twelve (12) months after your purchase
or delivery of the Product to a place designated by you or eighteen (18)
months from the date of manufacture whichever comes first (“Warranty
Period”). Warranty period for repaired Product cannot exceed beyond the
original warranty period before any repair work.
[Limitations]
(1) Y
ou are requested to conduct an initial failure diagnosis by yourself,
as a general rule. It can also be carried out by us or our service
company upon your request and the actual cost will be charged.
However, it will not be charged if we are responsible for the cause of
the failure.
(2) T
his limited warranty applies only when the condition, method,
environment, etc. of use are in compliance with the terms and
conditions and instructions that are set forth in the instruction manual
and user manual for the Product and the caution label affixed to the
Product.
(3) E
ven during the term of warranty, the repair cost will be charged on
you in the following cases;
(i)a failure caused by your improper storing or handling,
carelessness or negligence, etc., and a failure caused by your
hardware or software problem
(ii)a failure caused by any alteration, etc. to the Product made on
your side without our approval
(iii)a failure which may be regarded as avoidable, if your equipment
in which the Product is incorporated is equipped with a safety
device required by applicable laws and has any function or
structure considered to be indispensable according to a
common sense in the industry
(iv)a failure which may be regarded as avoidable if consumable
parts designated in the instruction manual, etc. are duly
maintained and replaced
(v)any replacement of consumable parts (battery, fan, smoothing
capacitor, etc.)
failure caused by external factors such as inevitable
(vi) a
accidents, including without limitation fire and abnormal
fluctuation of voltage, and acts of God, including without
limitation earthquake, lightning and natural disasters
(vii)a failure generated by an unforeseeable cause with a scientific technology that was not available at the time of the shipment of the Product from our company
(viii)any other failures which we are not responsible for or which you
acknowledge we are not responsible for
6-3
2.Term of warranty after the stop of production
(1) We may accept the repair at charge for another seven (7) years
after the production of the product is discontinued. The
announcement of the stop of production for each model can be seen
in our Sales and Service, etc.
(2) P
lease note that the Product (including its spare parts) cannot be
ordered after its stop of production.
3.Service in overseas countries
Our regional FA Center in overseas countries will accept the repair work
of the Product. However, the terms and conditions of the repair work
may differ depending on each FA Center. Please ask your local FA
Center for details.
4.Exclusion of responsibility for compensation against loss of
opportunity, secondary loss, etc.
Whether under or after the term of warranty, we assume no responsibility
for any damages arisen from causes for which we are not responsible, any
losses of opportunity and/or profit incurred by you due to a failure of the
Product, any damages, secondary damages or compensation for
accidents arisen under a specific circumstance that are foreseen or
unforeseen by our company, any damages to products other than the
Product, and also compensation for any replacement work, readjustment,
start-up test run of local machines and the Product and any other
operations conducted by you.
5.Change of Product specifications
Specifications listed in our catalogs, manuals or technical documents
may be changed without notice.
6.Application and use of the Product
(1) F
or the use of our General-Purpose AC Servo, its applications
should be those that may not result in a serious damage even if any
failure or malfunction occurs in General-Purpose AC Servo, and a
backup or fail-safe function should operate on an external system to
General-Purpose AC Servo when any failure or malfunction occurs.
(2) O
ur General-Purpose AC Servo is designed and manufactured as a
general purpose product for use at general industries. Therefore,
applications substantially influential on the public interest for such as
atomic power plants and other power plants of electric power
companies, and also which require a special quality assurance
system, including applications for railway companies and
government or public offices are not recommended, and we assume
no responsibility for any failure caused by these applications when
used.
In addition, applications which may be substantially influential to
human lives or properties for such as airlines, medical treatments,
railway service, incineration and fuel systems, man-operated
material handling equipment, entertainment machines, safety
machines, etc. are not recommended, and we assume no
responsibility for any failure caused by these applications when
used.
We will review the acceptability of the abovementioned applications,
if you agree not to require a specific quality for a specific application.
Please contact us for consultation.
Servo Amplifiers
MEMO
Servo Motors
Options/Peripheral
Equipment
LVS/Wires
Product List
Cautions
6-4
FA Products
PLC
MELSEC-Q Series Universal Model
Introducing the high-speed QCPU (QnUDVCPU) for faster processing of large data volumes.
◎Realize high-speed, high-accuracy machine control with various iQ Platform compatible controllers and multiple CPUs.
◎Easily connect to GOTs and Programming tools using built-in Ethernet port.
◎25 models from 10 k step small capacity to 1000 k step large capacity, are available.
◎Seamless communication and flexible integration at any network level.
Product Specifications
Program capacity
Number of I/O points [X/Y], number of
I/O device points [X/Y]
Basic instruction processing speed
(LD instruction)
External connection interface
Function module
Module extension style
Network
Programmable Controller
10k steps to 1000k steps
256 points to 4096 points/8192 points
120ns to 1.9ns
USB (all models equipped), Ethernet, RS-232, memory card, extended SRAM cassette
I/O, analog, high-speed counter, positioning, simple motion, temperature input,
temperature control, network module
Building block type
Ethernet, CC-Link IE controller network, CC-Link IE field network, CC-Link,
CC-Link/LT, MELSECNET/H, SSCNETⅢ (/H), AnyWire, RS-232, RS-422
MELSEC-L Series
“Light & Flexible” condensing various functions easily and flexibly.
◎CPU equipped as a standard with various functions including counter, positioning and CC-Link.
◎The base-less structure with high degree of freedom saves space in the control panel.
◎Easily confirm the system status and change the settings with the display unit.
◎Seven models are available in program capacities from 20 k steps to 260 k steps.
Product specifications
Program capacity
Number of input/output points [X/Y]
Number of input/output device points
[X/Y]
Basic instruction processing speed
(LD instruction)
External connection interface
Function modules
Unit expansion style
Network
HMI
20 k steps/60 k steps/260 k steps
1024 points/4096 points
8192 points
60 ns/ 40 ns/ 9.5 ns
USB, Ethernet, RS-232, SD memory card, CC-Link (L26CPU-BT/PBT)
I/O, analog, high-speed counter, positioning, simple motion,
temperature control, network module
Base-less structure
Ethernet, CC-Link IE Field network, CC-Link, CC-Link/LT, SSCNETIII(/H),
RS-232, RS-422
Graphic Operation Terminal GOT1000 Series GT16 Model
Full-flat face body integrating all the functions required of a HMI.
◎All models are equipped with Ethernet, RS-422/485 and RS-232 interfaces enabling a
diverse range of communications.
◎A multimedia unit and a video/RGB unit (optional) are supported for smooth recording and
playback of moving images.
◎USB host and device ports are provided as a standard on the front panel. Easily connect to
a personal computer for data exchange.
◎Large 15MB memory capacity allows you to use optional functions and real parts, etc.,
without worrying about memory space.
Product Specifications
Screen size
Resolution
Intensity adjustment
Touch panel type
Built-in interface
Applicable software
Input power supply voltage
6-5
15", 12.1", 10.4", 8.4", 5.7"
XGA, SVGA, VGA
8-step or 4-step adjustment
Analog resistive film
RS-232, RS-422/485, Ethernet, USB, CF card
GT Works3
100 to 240VAC (+10%, -15%), 24VDC (+25%, -20%)
Inverter
FREQROL-A700 Series
High-function, high-performance inverter
◎High-accuracy, high-response speed control using real sensor-less vector control is possible
with a general-purpose inverter having no PLG (encoder) (200% torque/0.3 Hz (3.7 K or less)).
◎Full-scale vector control is possible when used in combination with a motor with PLG (when using option).
◎The built-in noise filter (EMC filter) helps reduce noise generated from the inverter.
◎This series supports IPM motor operation. Use auto tuning to operate with the optimum motor characteristics.
Product Specifications
Inverter capacity
Control method
Output frequency range
PM offline auto tuning
Starting torque
Magnetic motor starters
200V class: 0.4kW to 90kW, 400V class: 0.4kW to 500kW
IPM control, Soft-PWM control, high-carrier frequency PWM control (Select from V/F,
advanced flux vector, or real sensor-less vector), vector control (when using options)
0.2 to 400Hz (real sensor-less vector, upper frequency during vector control is 120Hz)
200V class: 0.4K to 1.5K (150%3%ED), 2.2K/3.7K (100%3%ED)
When using the MM-CF Series, the motor constants, etc., are automatically
measured for operation with the optimum motor characteristics (IPM motors
other than the MM-CF Series, and other IPM motor brands are also supported)
200% 0.3Hz (3.7K or less), 150% 0.3Hz (5.5K or more)
(when using real sensor-less vector, vector control)
MS-T Series
Collection large satisfaction in a small body.
◎The industry-leading smallest dimension* is achieved in a general purpose Magnetic Contactor.
*In general Magnetic Contactors of 10A frame class (our survey in September, 2012)
◎Standard terminal cover improves safety.
◎Wide range of operation coil ratings available. Reducing inventory types and supporting selections.
◎Supporting your overseas business with compliance to various International Standards.
Product specifications
Frame
Applicable standards
Terminal cover
Improved wiring
Operation coil rating
Option units
Robot
10 A to 32 A
Certification to various standards including IEC, JIS, UL and CE (TÜV, CCC
certification pending)
Standard terminal cover improves safety, simplifies ordering, and reduces
inventory, etc.
Wiring and operability are improved with Streamling wiring terminal BC
specifications.
Wide range of operation coil ratings reduces number of coil types from 14 (N
Series) to seven types and simplifies selection.
Diverse lineup includes auxiliary contact blocks, surge absorber unit, and
mechanical interlock unit.
MELFA F Series
High speed, high precision and high reliability industrial robot
◎Compact body and slim arm design, allowing operating area to be expanded and load
capacity increased.
◎The fastest in its class using high performance motors and unique driver control technology.
◎Improved flexibility for robot layout design considerations.
◎Optimal motor control tuning set automatically based on operating position, posture, and
load conditions.
Product Specifications
Degrees of freedom
Installation
Maximum load capacity
Maximum reach radius
Vertical:6 Horizontal:4
Vertical:Floor-mount, ceiling mount, wall mount (Range of motion for J1 is limited)
Horizontal:Floor-mount
Vertical:2-7kg Horizontal:3-20kg
Vertical:504-908mm Horizontal:350-1,000mm
6-6
Global FA Centers
UK FA Center
German FA Center
Russian FA Center
Beijing FA Center
European FA Center
Korean FA Center
Tianjin FA Center
Guangzhou FA Center
Czech Republic FA Center
North American FA Center
Mitsubishi Electric Corp
Shanghai FA Center
Taiwan FA Center
Thailand FA Center
India FA Center
ASEAN FA Center
Brazil FA Center
China
Thailand
Brazil
Shanghai FA Center
MITSUBISHI ELECTRIC AUTOMATION
(CHINA) LTD. Shanghai FA Center
10F, Mitsubishi Electric Automation Center,
No.1386 Hongqiao Road, Changning District,
Shanghai, China
Tel: 86-21-2322-3030 Fax: 86-21-2322-3000 (9611#)
Thailand FA Center
MITSUBISHI ELECTRIC AUTOMATION
(THAILAND) CO., LTD.
Bang-Chan Industrial Estate No.111 Soi Serithai
54, T.Kannayao, A.Kannayao, Bangkok 10230,
Thailand
Tel: 66-2906-3238 Fax: 66-2906-3239
Brazil FA Center
MITSUBISHI ELECTRIC DO BRASIL
COMÉRCIO E SERVIÇOS LTDA.
Rua Jussara, 1750 - Bloco B- Sala 01, Jardim Santa
Cecília - CEP 06465-070, Barueri - SP, Brasil
Tel: 55-11-4689-3000 Fax: 55-11-4689-3016
Beijing FA Center
MITSUBISHI ELECTRIC AUTOMATION
(CHINA) LTD. Beijing FA Center
Unit 908, Office Tower 1, Henderson Centre,
18 Jianguomennei Avenue, Dongcheng District,
Beijing, China
Tel: 86-10-6518-8830 Fax: 86-10-6518-3907
ASEAN
European FA Center
MITSUBISHI ELECTRIC EUROPE B.V.
Polish Branch
32-083 Balice ul. Krakowska 50, Poland
Tel: 48-12-630-47-00 Fax: 48-12-630-47-01
Tianjin FA Center
MITSUBISHI ELECTRIC AUTOMATION
(CHINA) LTD. Tianjin FA Center
Room 2003 City Tower, No.35, Youyi Road,
Hexi District, Tianjin, China
Tel: 86-22-2813-1015 Fax: 86-22-2813-1017
Guangzhou FA Center
MITSUBISHI ELECTRIC AUTOMATION
(CHINA) LTD. Guangzhou FA Center
Room 1609, North Tower, The Hub Center,
No.1068, Xingang East Road, Haizhu District,
Guangzhou, China
Tel: 86-20-8923-6730 Fax: 86-20-8923-6715
Taiwan
Taiwan FA Center
SETSUYO ENTERPRISE CO., LTD.
3F, No.105, Wugong 3rd Road, Wugu District,
New Taipei City 24889, Taiwan, R.O.C.
Tel: 886-2-2299-9917 Fax: 886-2-2299-9963
Korea
Korean FA Center
MITSUBISHI ELECTRIC AUTOMATION
KOREA CO., LTD. (Service)
B1F, 2F, 1480-6, Gayang-Dong, Gangseo-Gu,
Seoul, 157-200, Korea
Tel: 82-2-3660-9630 Fax: 82-2-3663-0475
6-7
ASEAN FA Center
MITSUBISHI ELECTRIC ASIA PTE. LTD.
ASEAN Factory Automation Centre
307 Alexandra Road, Mitsubishi Electric Building,
Singapore 159943
Tel: 65-6470-2480 Fax: 65-6476-7439
India
India FA Center
MITSUBISHI ELECTRIC INDIA PVT. LTD.
India Factory Automation Centre
Emerald House, EL-3, J Block, M.I.D.C., Bhosari,
Pune, 411026, Maharashtra State, India
Tel: 91-20-2710-2000 Fax: 91-20-2710-2100
MITSUBISHI ELECTRIC INDIA PVT. LTD.
India Factory Automation Centre Gurgaon Branch
2nd Floor, Tower A & B, Cyber Greens, DLF
Cyber City, DLF Phase - III, Gurgaon - 122002
Haryana, India
Tel: 91-124-463-0300 Fax: 91-124-463-0399
MITSUBISHI ELECTRIC INDIA PVT. LTD.
India Factory Automation Centre Bangalore Branch
Prestige Emerald, 6th Floor, Municipal No.2,
Madras Bank Road, Bangalore 560001, India
Tel: 91-80-4020-1600 Fax: 91-80-4020-1699
America
North American FA Center
MITSUBISHI ELECTRIC AUTOMATION, INC.
500 Corporate Woods Parkway, Vernon Hills,
IL 60061, U.S.A.
Tel: 1-847-478-2100 Fax: 1-847-478-2253
Europe
German FA Center
MITSUBISHI ELECTRIC EUROPE B.V.
German Branch
Gothaer Strasse 8, D-40880 Ratingen, Germany
Tel: 49-2102-486-0 Fax: 49-2102-486-1120
UK FA Center
MITSUBISHI ELECTRIC EUROPE B.V. UK
Branch
Travellers Lane, Hatfield, Hertfordshire, AL10
8XB, U.K.
Tel: 44-1707-28-8780 Fax: 44-1707-27-8695
Czech Republic FA Center
MITSUBISHI ELECTRIC EUROPE B.V.
Czech Branch
Avenir Business Park, Radicka 751/113e,
158 00 Praha5, Czech Republic
Tel: 420-251-551-470 Fax: 420-251-551-471
Russian FA Center
MITSUBISHI ELECTRIC EUROPE B.V.
Russian Branch St. Petersburg office
Piskarevsky pr. 2, bld 2, lit "Sch", BC "Benua",
office 720; 195027, St. Petersburg, Russia
Tel: 7-812-633-3497 Fax: 7-812-633-3499
Microsoft, Windows, Internet Explorer, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other
countries.
Celeron and Pentium are registered trademarks of Intel Corporation.
Ethernet is a trademark of Xerox Corporation.
All other company names and product names used in this document are trademarks or registered trademarks of their respective companies.
6-8
SERVO AMPLIFIERS & MOTORS
Safety Warning
To ensure proper use of the products listed in this catalog,
please be sure to read the instruction manual prior to use.
Country/Region Sales office
Tel/Fax
USA
MITSUBISHI ELECTRIC AUTOMATION, INC.
500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A.
Tel : +1-847-478-2100
Fax : +1-847-478-2253
Brazil
MITSUBISHI ELECTRIC DO BRASIL COMÉRCIO E SERVIÇOS LTDA.
Rua Jussara, 1750 - Bloco B- Sala 01, Jardim Santa Cecília - CEP 06465-070,
Barueri - SP, Brasil
Tel : +55-11-4689-3000
Fax : +55-11-4689-3016
Germany
MITSUBISHI ELECTRIC EUROPE B.V. German Branch
Gothaer Strasse 8, D-40880 Ratingen, Germany
Tel : +49-2102-486-0
Fax : +49-2102-486-1120
UK
MITSUBISHI ELECTRIC EUROPE B.V. UK Branch
Travellers Lane, Hatfield, Hertfordshire, AL10 8XB, U.K.
Tel : +44-1707-28-8780
Fax : +44-1707-27-8695
Italy
MITSUBISHI ELECTRIC EUROPE B.V. Italian Branch
VIALE COLLEONI 7 - 20864 Agrate Brianza (Milano), Italy
Tel : +39-039-60531
Fax : +39-039-6053-312
Spain
MITSUBISHI ELECTRIC EUROPE, B.V. Spanish Branch
Tel : +34-935-65-3131
Carretera de Rubí 76-80-AC.420, E-08190 Sant Cugat del Vallés (Barcelona), Spain Fax : +34-935-89-1579
France
MITSUBISHI ELECTRIC EUROPE B.V. French Branch
25, Boulevard des Bouvets, F-92741 Nanterre Cedex, France
Tel : +33-1-55-68-55-68
Fax : +33-1-55-68-57-57
Czech Republic MITSUBISHI ELECTRIC EUROPE B.V. Czech Branch
Avenir Business Park, Radicka 751/113e, 158 00 Praha5, Czech Republic
Tel : +420-251-551-470
Fax : +420-251-551-471
Poland
MITSUBISHI ELECTRIC EUROPE B.V. Polish Branch
32-083 Balice ul. Krakowska 50, Poland
Tel : +48-12-630-47-00
Fax : +48-12-630-47-01
Russia
MITSUBISHI ELECTRIC EUROPE B.V. Russian Branch St. Petersburg office
Piskarevsky pr. 2, bld 2, lit "Sch", BC "Benua", office 720; 195027,
St. Petersburg, Russia
Tel : +7-812-633-3497
Fax : +7-812-633-3499
South Africa
ADROIT TECHNOLOGIES
20 Waterford Office Park, 189 Witkoppen Road, ZA-Fourways, South Africa
Tel : +27-11-658-8100
Fax : +27-11-658-8101
China
MITSUBISHI ELECTRIC AUTOMATION (CHINA) LTD.
No.1386 Hongqiao Road, Mitsubishi Electric Automation Center, Changning
District, Shanghai, China
Tel : +86-21-2322-3030
Fax : +86-21-2322-3000
Taiwan
SETSUYO ENTERPRISE CO., LTD.
6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan,
R.O.C.
Tel : +886-2-2299-2499
Fax : +886-2-2299-2509
Korea
MITSUBISHI ELECTRIC AUTOMATION KOREA CO., LTD. (Sales)
3F, 1480-6, Gayang-Dong, Gangseo-Gu, Seoul, 157-200, Korea
Tel : +82-2-3660-9510
Fax : +82-2-3664-8372/8335
Singapore
MITSUBISHI ELECTRIC ASIA PTE. LTD -Industrial Division
307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943
Tel : +65-6473-2308
Fax : +65-6476-7439
Thailand
MITSUBISHI ELECTRIC AUTOMATION (THAILAND) CO., LTD.
Bang-Chan Industrial Estate No.111 Soi Serithai 54, T.Kannayao, A.Kannayao,
Bangkok 10230, Thailand
Tel : +66-2906-3238
Fax : +66-2906-3239
Indonesia
P. T. Autoteknindo Sumber Makmur
Muara Karang Selatan, Block A / Utara No.1 Kav. No. 11, Kawasan Industri
Pergudangan, Jakarta- Utara 14440, P.O.Box 5045, Indonesia
Tel : +62-21-663-0833
Fax : +62-21-663-0832
India
MITSUBISHI ELECTRIC INDIA PVT. LTD.
Emerald House, EL-3, J Block, M.I.D.C., Bhosari, Pune, 411026, Maharashtra
State, India
Tel : +91-20-2710-2000
Fax : +91-20-2710-2100
Australia
MITSUBISHI ELECTRIC AUSTRALIA PTY. LTD.
348 Victoria Road, P.O. Box 11, Rydalmere, N.S.W 2116, Australia
Tel : +61-2-9684-7777
Fax : +61-2-9684-7245
L(NA)03086ENG-B 1307 Printed in Japan (MDOC)
New publication, effective July 2013.
Specifications are subject to change without notice.