Craftsman 139.53637SRT1 Owner`s manual

SEARS
OWNER'S
MANUAL
Model No.
139.53525SRT
139.53627SRT
139.53636SRT
139.53640SRT
139.53641SRT
For Residential
I:RRFTSMRNo
Use
1/2 HP
GARAGE DOOR OPENER
Only
Caution:
Read and follow
• Safety Precautions
all
safety rules and
operating instructions
before first use of this
• Assembly
• Installation
• Adjustment
• Care and Maintenance
product.
• Operation
Fasten the manual
• Troubleshooting
• Parts List
near the garage door
after installation.
Complies with UL 325
regulations effective
January !, 1993
/11 ii
"N_
Sears,
Roebuck
and Co., Hoffman
Estates,
IL 60179 U.S.A.
Contents
Page
A review of safety alert symbols ................................. 2
You'll need tools .......................................................... 3
Contents
Page
Install the light and lens ................................................. 19
Safety information regarding garage door locks
and ropes .................................................................. 3
Electrical requirememts ................................................. 20
Safety reversing sensor information .............................. 21
Testing your garage door for sticking, binding
and balance ............................................................... 3
Illustration of sectional door installation ..................... 4
Install the safety reversing sensor ........................... 22, 23
Fasten door bracket (sectional door) ............................ 24
Illustration of one-piece door installation ................... 5
Carton inventory .......................................................... 6
Hardware inventory ..................................................... 7
Assembly section - pages 8 - 11
Assemble T-rail ......................................................... 8
Attach cable pulley bracket ....................................... 8
Install trolley .............................................................. 9
Fasten T-rail to opener ............................................. 9
Install chain/cable ................................................... 10
Attach sprocket cover ............................................. 10
Tighten the chain and cable ................................... 11
Installation section - pages 11 - 27
Installation safety instructions ................................. 11
Determine header bracket location
Sectional door ....................................................... 12
One-piece door ..................................................... 13
Install the header bracket ....................................... 14
Attach the T-rail to header bracket ......................... 15
Position the opener ................................................. 16
Hang the opener ..................................................... 17
Install the wall control ............................................. 18
Start by reviewing
Attach emergency release rope and handle ................. 19
Fasten door bracket (one-piece door) ........................... 25
Connect door arm to trolley (sectional door) ................. 26
Connect door arm to trolley (one-piece door) ............... 27
Adjustment
section - pages 28 - 30
Travel limit adjustments ................................................. 28
Force adjustments ......................................................... 29
Test the safety reversing sensor ................................... 30
Test the safety reverse system .................................... 30
Operation safety instructions ........................................... 31
Care of your opener ......................................................... 31
Maintenance schedule .................................................... 31
Operation of your opener ................................................ 32
Receiver and remote control programming .................... 33
Having a problem? .................................................... 34, 35
Repair parts, rail assembly .............................................. 36
Repair parts, installation .................................................. 36
Repair parts, opener assembly ....................................... 37
Accessories ...................................................................... 38
Index ................................................................................ 39
How to order repair parts ................................................. 40
Maintenance agreement .................................................. 40
Warranty .......................................................................... 40
these important safety alert symbols
When you see these Safety Symbols on the following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the corresponding instructions. The hazard may
come from something mechanical or from electric shock. Read the instructions carefully.
Mechanical
Electrical
When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage
to your garage door and/or the garage door opener if you do not comply with the corresponding
instructions. Read the instructions
carefully.
This garage door opener is designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the safety instructions contained in this manual.
You'll Need Tools
During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below.
Pencil
Level
Hack Saw
Tape Measure
Wire Cutters
CIaw Hammer
3/16", 5/16" and
5/32" Dritt Bits
D)
StepIadder
ts
An unbalanced garage door might not reverse
when required and someone under the door
could be seriously injured or killed.
If your garage door binds, sticks or is out of
balance, call for professional
garage door
service. Garage doors, door springs, cables,
pulleys, brackets and their hardware are under
extreme tension and can cause serious injury
or death. Do not try to loosen, move or adjust
them yourself!
Ropes left on a garage door could cause
someone to become entangled
and killed.
Remove all ropes connected to the door before
installing and operating the opener.
Identify the type and height of your door and any
special conditions that exist and any additional
materials that may be required by referring to the lists
on page 4 or page 5.
Screwdriver
Adjustable
End Wrench
To avoid damage to the garage door and
opener, disable locks before installing and
operating the opener. Use a wood screw or nail
to hold locks in the "open"
(unlocked)
position.
Operation at other than 120V 60 Hz will cause
opener malfunction and damage.
Before you begin, complete the following test to
make sure your door is balanced, and is not
sticking or binding:
• Lift the door about halfway as shown. Release the
door. It should stay in place, supported entirely by
its springs.
• Raise and lower the door to see if there is any
binding or sticking.
ONE-PIECE
DOOR
Before you begin, survey your garage area to
see whether any of the conditions below apply
to your installation.
Horizontal
FINISHED CEILING
Support bracket &
fastening hardware
is required
See page 17
and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steet, aluminum, door
with glass panels, etc)
See page 24 for details
i _ Header
Stack in Chain Tension
is NormaI When
Garage Door is Closed
Wail
Extension
Spring
OR
Torsion
Access
Door
Spring
O
Safety
Sensor
Floor must be level
across width of door.
Safety Reversing
Sensor
Header
_racket
Based on your particular requirements, there are
several installation steps which might call for
materials and/or hardware not included in the carton.
Closed Position
Cable PulIey
_
Bracket
Rail Assembly
'//_
• Step 1, page 12 - Look at the wall or ceiling above
the garage door. The header bracket must be
securely fastened to structural supports.
Cable
<_;TX_
-- Door
Tr°llle
........
h............
/ /
Emergency Release
Rope & Handle
• Step 5, page 17 - Do you have a finished ceiling in
your garage? tf so, a support bracket and
additional fastening hardware may be required.
/_:/ Straight
/,_7_
Door
s! iArm
• Safety reversing sensor, page 21 - Depending
upon garage construction, wood blocks may need
to be fastened to mounting locations before
sensors are installed.
Header
Wall
Garage
Door
• Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor will require hardware not
provided.
_
Door
Arm "
Door Bracket
• The opener can be installed within 2 feet to the left
or right of the door center if there is a torsion spring
or center bearing plate in the way of the header
bracket or door bracket area. If your door has
extension springs, the opener must be installed
in the center of the door. See pages 12 and 24.
• Step 11, page 24 - Do you have a steel, aluminum,
fiberglass or glass panel door? If so, horizontal
and vertical reinforcement is required.
• Look at the garage door where it meets the floor.
It must close on the floor all the way across.
Otherwise, the safety reverse system may not
work properly. See page 30. Floor or door should
be repaired.
• Do you have an access door in addition to the
garage door? If not, Model 53702 Emergency
Key Release is required. See page 38.
You may find it helpful to refer back to this page as
you proceed with the installation of your opener.
• If your door is more than 7 feet high, see the
longer rails available on page 38.
4
One-Piece
Before you begin, survey your garage area to
see whether any of the conditions below apply
to your installation,
Door without
Track
FINISHED CEILING
Support bracket
& fastening
hardware is required.
See page 17.
Slack in chain tension
is normal when
garage door is ctosed.
Header
Wall
Closed Position
Cable
Pulley Bracket
Cabie
Access Door
Trolley
O
Emergency
Release
Straight
Door
Arm
Curved
Door
Arm
Rope
&HandIe
ge
Door
Reversing
) between floor and bottom
Sensor
Safety
of door must not exceed 1/4".
Reversing Sensor
One-Piece
Door with Track
Based on your particular requirements, there are
several installation steps which might call for
materials and/or hardware not included in the carton.
• Step 1, page 13 - Look at the wall or ceiling above
the garage door. The header bracket must be
securely fastened to structural supports.
• Step 5, page 17 - Do you have a finished ceiling in
your garage? tf so, a support bracket and
additional fastening hardware (not supplied) may
be required.
• Safety reversing sensor, page 21 - Depending on
garage construction, wood blocks may need to be
securely fastened to mounting locations before
sensors are installed.
• Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor will require hardware that
is not provided.
• Step 11, page 25 - Generally, a one-piece door
does not require reinforcement. If your door is
lightweight, you can refer to the information
relating to sectional doors on page 24.
• Step 11, page 25 - Depending on your door's
construction, you might need additional mounting
hardware for the door bracket.
• Do you have an access door in addition to the
garage door? If not, Model 53702 Emergency Key
Release is required. See page 38.
• The gap between the bottom of the garage
door and the floor cannot exceed 1/4",
Otherwise, the safety reverse system may not
work properly. See page 30. The floor or the door
should be repaired.
Access
Door
I
I
• ;afet-_
Floor must be level
across width of door
Safety
Reversing
Sensor
_g
Sensor
Closed Position
Cable
Cable
Trotley
I
I_
Pulley Bracket
HW° I r
\ eaderDurved
UoorArm_- /
Bracket
J_
y/z,,/_
Garage -- _///:1
Door
°°°°°°°l°°°°}J
I
_ Door
Bracket
Straight
Door
Chain
I
I
T-rail
I
I Emergency
Release
J_-
Rope & Haedte
Arm
You may find it helpful to refer back to this page
as you proceed with the installation of your
opener.
Opener Carton inventory
Your garage door opener is packaged in two cartons which contain all parts illustrated below. If anything is
missing, carefully check the packing material. Parts may be "stuck" in the foam. Hardware for assembly and
installation is shown on page 7.
Modets 53824 (2), 53637 (2),
53635 (2), 53629 (1), 53628 (2),
53425 (1), 53325 (1)
Three-Function
Remote Controt
with Visor Clip (1)
Mode153225
only
Models 53637,
53635, & 53425
Model 53635 only
Multi-Function
Keylees Entry
Single-Function
Remote ControI
with Visor Drip (1)
Lighted ConeoIe
Wall ControI
Modet
Models 53225,
53325, 53628, 53629
53824
only
_€_
Model 53629 only
Deluxe Wall Control
Pulley Bracket
Three-Function
Compact
Remote Control
2-Conductor
Lighted Push Button
Wall Controt
and Hardware
Be,Wire
White & White/Red
/
/
_
_//_
_/
_<_/
y./_
T-Ro,
J
Door Bracket
Modets 53824, 53637, 53635,
53629, 53628, 53425, 53325
End
sections
Door Bracket
Plate
Sprocket
Light Lens
Cover
"C" Wrap (2)
Header Bracket
Chain and Cable
in Dispensing
Safety
Reversing
Mounting
With
Square
Carton
Sensor
Hanging Brackets
Bracket
Holes
(2)
Curved Door
Arm Section
Safety Reversing Sensor
Mounting Bracket
With Stot (2)
Safety Labets
and
Literature
(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with
2-Conductor White & White/Black BelI Wire
attached
Straight Door
Arm Section
Separate all hardware from the packages in the rail carton and the opener
shown below, for the assembly
and installation procedures.
Assembly
carton,
as
Hardware
i
Washered
Screw
5/16" - 18 x 1/2" (2)
(mounted in opener)
Hex Screw
Nut
5/16" - 18 x 7/8" (3)
5/16" - 18 (5)
Carriage Bolts
1/4"- 20 x 1/2" (4)
Master Link (2)
©
©
Trolley Threaded
Shaft (1)
Lock Nut
1/4" - 20 x 7/16"
Lock Washer
5/16" (4)
Installation
(4)
Hardware
,1111111111
Hex Screw
5/16"- 18 x 7/8" (4)
Rail Grease
Handte
5/16"-18 x 1-7/8"
©
©
(4)
Nut 5/16" - 18 (6)
Lock Washer
5/16" (6)
Rope
Screw
Carriage Bott
5/16"-18 x 2-1/2" (2)
6AB x 1" (2)
Dry Wail Anchors (2)
O
o]
Clevis Pin
Insulated
CIevis Pin
5/16" x 2-3/4" (1)
Staples (10)
5/16" x 1" (2)
Ring
Fastener (3)
Safety Reversing Sensor
Installation Hardware
©
Carriage Botts
1/4"- 20 x 1/2" (4)
Lock Nut
1/4"- 20 (4)
Wing Nut (2)
©
Hex Screw
1/4-20 x 1-1/2" (2)
Screw
#10 -32 x 3/8"(4)
Lock Nut
#10 x 32 (4)
Insulated
Staples (20)
Assembly Section: Pages 8To avoid installation
Assembly
Assemble
difficulties,
do not run the garage door opener
Make sure
Step 1
bolt necks
until instructed to do so.
are
seated in the square
holes and rails are
the T=rail & Attach
the Cable Pulley
11
aligned before you
tighten lock nuts, (See
right and wrong views).
Improper assembly
can
cause jerky trolley
operation,
noise and/or
Bracket
Align the 3 T-rail sections on a flat surface exactly
as shown. The end sections are identical. Make
sure the "arrow label" on the center section is
pointing toward the door.
Right
Wrong
nuisance door reversals.
T-RAIL
(TO
Insert the carriage bolts so the square bolt necks
seat in the square holes in the T-rail end sections
and pass through the round holes in T-rail center
section. Assemble lock nuts, ensure alignment and
tighten.
BACK
OPENER)
T-rait
1/4" Lock Nut
(End Section)
\
@
Brace
T-rail
if T-rail
is not assembled
(Center Section)
EXACTLY
as shown, trolley
will not travel smoothly
along length of rail or it will
hit against the nuts.
Brace
\
T-rail
(End Section)
Hardware Shown Actual Size
Cable pulley bracket
attaches to FRONT
END of T-rait
©
Square Carriage
Bolt Holes
Lock Nut
1/4" - 20 x 7/16"
Carriage Botts
1/4" - 20 x 1/2"
T-RAIL FRONT
(TO DOOR)
Hex Screw
Position the cable pulley bracket on the front end of the
T-rail as shown. Fasten securely with the hardware.
5/16" - 18 x 7/8"
Nut
5/16"
- 18
Lock Washer
5/16"
Hex Screws
5/16"-18x7/8"
When tightening
the screws,
be
sure to keep
bracket
parallel
to the rai!.
Right
Lock Washer
5/16"
Wrong
Otherwise,
the
rail may bow
when opener is
operated.
Assembly
Install
Hardware Shown
Actual Size
Step 2
the Trolley on the T-rail
• Attach the threaded shaft to the trolley with the
lock washer and nuts as shown.
©
Lock Washer
5/16"
Nut
5/16"-18
Lock Washer
5/16"
Outer Nut
Trolley
Threaded Shaft
Inner Nut
5/16"
TroIiey
Temporary Stop
Screwdriver
• As a temporary stop, insert a screwdriver into the
hole in the front end of the T-rail.
\
• Slide the trolley assembly along the rail to the
screwdriver stop.
If trolley hits against any nuts on the T-rail, the
bolts and nuts were attached from the wrong
side and must be repositioned. Review Step 1.
Assembly
Fasten
Step 3
the T-rail to the Opener
• Place the opener on packing material to protect
the cover. For convenience, put a support under
the cable pulley bracket.
Remove the (2) 5/16"-18x1/2" washered screws
mounted in the top of the opener.
Washered Screw
5/16"-18xl/2"
Align the holes in the back section of the T-rail with
the holes in the opener.
Hex Screw
5/16"-18x7/8"
Fasten the rail with the (2) washered screws
previously removed. Tighten securely.
Remember to use only these screws! Any other
screws will cause serious damage to the opener.
Insert a 5/16"-18x7/8" hex screw into the trolley
stop hole in the T-rail as shown. Tighten securely
with a 5/16" lock washer and nut. This screw limits
trolley travel in the UP direction.
Hardware Shown Actual Size
D©
Hex Screw
5/16"- 18x7/8"
Nut
5/16"
Lock Washer
5/16"
Trotley
Stop
T-rail
(Back Section)
5/16"
5/16"-18
Assembly
Step 4
Install the Chain/Cable
&
Attach the Sprocket
Cover
Dispensing
Serious injury can result if fingers become
entangled in moving opener sprocket. Attach
sprocket cover securely. Never operate opener
while your hand is near the opener sprocket.
Carton
Opener
Sprocket
Figure 2
Leave Chain and Cable
Inside Dispensing
Carton to Prevent Kinking.
Keep Chain and CabIe
Taut When Dispensing
• Detach the cable loop from the carton and fasten it
to the trolley with a master link from the hardware
bag. See master link procedure, Figure 1.
• With the trolley against the screwdriver, dispense
the cable around the pulley.
Figure 3
Master Link
• Proceed back around the opener sprocket,
Figure 2. Be sure sprocket teeth engage the chain.
Continue forward to the trolley threaded shaft,
Figure 3.
Master Link
• Use the second master link to connect the
CIip-On Spring
chain to the flat end of the shaft. Check
to make sure the chain is not
Mast
Link Cap
twisted.
Clip-On Spring
_ _
i
Master
Link Cap
Flat End
i
i
i
i
of TrolIey
Threaded Shaft
; _
Chain
• Remove the screwdriver.
T-rail
Cable
Loop
_.
Pin Notch
Master
LinkBar
Sable
Pulley
Figure
1
Master Link Procedure:
Install Chain and Cabte
In This Direction
Push pins of master link bar
through cable loop and hole in
front end of trolley. Push cap
over pins and into notches.
Slide clip-on spring over cap
and into notches until both
Sprocket
Cover
Back Tab Slot
pins are securely locked.
Top of Opener
To attach the sprocket
Front Tab Slot
cover:
• Insert the back tab in the opener slot. Squeeze the
cover slightly and insert the front tab in the slot on
the mounting plate.
Mounting
Plate
10
Assembly
Step 5
Tighten the Chain & Cable
Outer Nut
• Spin the inner nut and lock washer down the
threaded shaft, away from the trolley.
Lock
Washer
Inner Nut
\\
/
• To tighten the chain, turn outer nut in the direction
shown. As you turn the nut, keep the chain
from twisting.
• When the chain is approximately 1/2" above the
base of the T-rail at its midpoint, re-tighten the
inner nut to secure the adjustment.
TroIley
_
Sprocket noise can result if chain is either too
loose or too tight.
Chain
When installation is complete, you may notice some
chain droop with the door closed. This is normal. If
the chain returns to the position shown when the
door is open, do not re-adjust the chain.
1/2 Inch
NOTE: During future maintenance, ALWAYS
pull the emergency release handle to disconnect
trolley before adjusting chain.
Base of T-rait
You have now finished assembling your garage door opener. Please read the following
warnings before proceeding to the installation section:
IMPORTANT INSTALLATION INSTRUCTIONS
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW
ALL INSTALLATION
INSTRUCTIONS.
2. Install only on a properly balanced and lubricated garage door. An improperly balanced door
may not reverse and could result in severe injury or death. Repairs to cables, spring assemblies
and other hardware must be made by a professional service person before installing opener.
3. Disable all locks and remove all ropes connected to the garage door before installing the opener.
Ropes connected to a garage door can cause entanglement and death.
4. If possible, install door opener 7 feet or more above floor with the emergency release handle
mounted 6 feet above the floor.
5. Do not connect the opener to power source until instructed to do so.
6. Locate the Wall Control within sight of the door at a minimum height of 5 feet where small
children cannot reach and away from all moving parts of the door.
7. Install the User Safety Instruction Label on the wall adjacent to the control button and the
Maintenance Instruction Label in a prominent location on the inside of the garage door.
8. Upon completion of the installation, the door must reverse when it comes in contact with a
one-inch high object or a 2x4 laid fiat on the floor.
9. Do not wear watches, rings or loose clothing while installing or servicing an opener. Jewelry or
loose clothing can be caught in the mechanism of the garage door or the opener.
11
Installation
Installation
Determine
Section:
Step 1
Header
Bracket
Location
If the header bracket is not rigidly fastened to
a structural support on the header wall or
ceiling, the safety reverse system may not
work properly (see page 30). The door might
not reverse when required, and could cause
serious injury or death.
Installation procedures vary according to
garage door types. Follow the instructions
which apply to your door.
The garage door springs,
cables, pulleys,
brackets and their hardware are under extreme
tension. Do not attempt to loosen, move or
adjust them yourself. Serious personal injury
or death could result. Call for professional
garage door service.
Finished
Header
Wall
Pages 12 - 27
Vertical
GuideIine
Ceiling
2x4
• Close the door and mark the inside
vertical centerline of the garage door.
• Extend the line onto the header wall
above the door.
Structural
Remember, you can fasten the
header bracket within 2 feet of the
left or right of the door center only if
a torsion spring or center bearing
plate is in the way; or you can attach
it to the ceiling (refer to page 14)
when clearance is minimal. (It may
be mounted on the wall upside down
if necessary, to gain approximately
1/2".)
If you need to install the header bracket
on a 2x4 (on wall or ceiling), use lag
screws (not supplied) to securely fasten
the 2x4 to structural supports as shown
here and on page 13.
Ceiting
Header
• Open your door to the highest
point of travel as shown. Draw
an intersecting horizontal line
on the header wall 2" above
the high point. This height will
provide travel clearance for the
top edge of the door.
Door clearance brackets are
available for sectional doors
when headroom clearance is
less than 2". See accessory
page 38.
,
i
2"
I
Header
_Wall
Highest Point
of Travel
Door
Sectional door
with curved track
Proceed
Track
to Step 2, page 14.
12
One-piece door
with horizontal track
Track
Read the Safety instructions
on page 12. They also apply to doors without
tracks.
Unfinished
Header Wail
\
Vertical
Centeriine
2x4
• Close the door and mark the
inside vertical centerline of
your garage door. Extend the
line onto the header wall
above door.
If headroom clearance is
minimal, you can install the
header bracket on the ceiling.
See page 14.
OPTIONAL
FOR
CEILING
HEADER
MOUNT
BRACKET
• If you need to install the
header bracket on a 2x4 (on
wall or ceiling), use lag screws
(not supplied) to securely
fasten the 2x4 to structural
supports as shown.
Header Wail
_:_l
Ij
Highest Point
One-piece door without track
jamb hardware
• Open your door to the highest
shown. Measure the distance
door to the floor. Subtract the
door. Add 8" to the remainder.
One-piece door without track
pivot hardware
EXAMPLE
point of travel as
from the top of the
actual height of the
(See Example).
Distance from top of door
(at highest point of travel) to floor ........................... 92"
Actual height of door ............................................. -88"
Remainder ................................................................
4"
• Close the door and draw an intersecting horizontal
line on the header wall at the determined height.
Add .........................................................................
If the total number of inches exceeds the height
available in your garage, use the maximum
height possible, or refer to page 14 for ceiling
installation.
Proceed
+8"
Bracket height on header wall .............................. =12"
(Measure UP from top of CLOSED door.)
to Step 2, page 14.
13
Installation
Install
You can attach the header bracket either to the
wall above the garage door, or to the ceiling,
Follow the instructions which will work best for
your particular requirements.
Step 2
the Header
Bracket
Fasten the Header
• Center the bracket on the vertical guideline with
the bottom edge of the bracket on the horizontal
line as shown (with the arrow pointing toward the
ceiling).
Bracket
to the Wall
• Mark either set of bracket holes (do not use the
holes designated for ceiling mount). Drill 3/16" pilot
holes and fasten the bracket securely to a structural
support with the hardware provided.
Wail
Mounting Holes
__ Header
Wall
_
//
/
Lag Screws
5/16"x18x1-7/8"
2x4
Structural
Support
Door
Spring
The nail hole is for positioning
only You must use lag screws to
mount the header bracket.
Optional
Wall Mounting
Holes
Door
Highest
Point of Travel
(of Garage Door)
Hardware Shown Actual Size
Vertical
Center
Line
'>
5/16"-18xl
Fasten the Header
Bracket
-7/8"
to the Ceiling
• Extend the vertical guideline onto the ceiling as
shown.
• Center the bracket on the vertical mark, no more
than 6" from the wall. Make sure the arrow is
pointing toward the wall. The bracket can be
mounted flush against the ceiling when clearance
is minimal.
• Mark holes designated for ceiling mount only. Drill
3/16" pilot holes and fasten bracket securely to a
structural support with the hardware provided.
>_
Door
Spring
Ceiling Mounting Holes
The nail hote is for positioning only.
You must use lag screws to mount
the header bracket.
14
t _
Screws
5/16"x18x1-7/8"
Installation
Step 3
Attach the T-rail to the Header
--
Bracket
• Position the opener on the garage floor below the
header bracket. Use packing material as a
protective base.
Header WalI
If the door spring is in the way you'll need help.
Have someone hold the opener securely on a
temporary support to allow the T-rail to clear the
spring.
Header
Bracket
Cable
Putley
Bracket
• Position the cable pulley bracket against the header
bracket.
• Align the bracket holes and join with a clevis pin as
shown.
• Insert a ring fastener to secure.
Ring Fastener
Header Bracket
0
i
C_
\\
Ctevis Pin
5/16"x2-3/4 "
I
Cable
Pulley
Bracket
Door
Temporary
Support
Hardware Shown Actual Size
°1
Clevis Pin
5/16"x2-3/4"
O
Ring Fastener
15
Installation
Position
Step 4
the Opener
Follow instructions
type as illustrated.
which apply to your door
A 2x4 laid fiat is convenient for setting an ideal
door-to-T-rail distance.
2x4
Laid Fiat
• Raise the opener onto a stepladder.
You will need help at this point if the ladder is
not taft enough.
• Open the door all the way and place a 2x4 laid fiat
on the top section beneath the T-rail.
Door
If the top panel hits the trolley when you raise
the door, pull down on the trolley release arm to
disconnect the inner and outer sections. The
trolley can remain disconnected
until Step 12 is
completed.
Tro, y
• With the door fully open and parallel to the floor,
measure the distance from the floor to the top of
the door.
Top of Opener
1I
• Using a stepladder as a support, raise the opener
to the same distance as the door from the floor (it
will be at a slight angle as shown).
Top
• The top of the door should be level with the top of
the opener. Do not position the opener more than
2" above this point.
t
16
of Door
nstallation Step 5
Hang the Opener
Two representative installations are shown.
Yours may be different. Hanging brackets should
be angled, Figure 1, to provide rigid support. On
finished ceilings, Figure 2, attach a sturdy metal
bracket to structural supports before installing the
opener. The bracket and fastening hardware are not
supplied. See accessory page 38.
Figure 1
/ Supports
/
• Measure the distance from each side of the opener
to the structural support.
• Cut both pieces of the hanging bracket to required
lengths.
Measure
Distance
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
• Drill 3/18" pilot holes in the structural supports.
• Attach one end of each bracket to a support with
5/16"xl-7/8" lag screws.
• Fasten the opener to the hanging brackets with
5/18"-18x7/8" screws, lock washers and nuts.
• Check to make sure the T-rail is centered over the
door (or in line with the header bracket if the
bracket is not centered above the door).
• Remove the 2x4. Operate the door manually. If the
door hits the rail, raise the header bracket.
Figure 2
5/16" Lock Washer
5/16"- 18
Hardware Shown Actual Size
Lag Screw
5/16"-18xl -7/8"
©
Hex Screw
5/16"- 18x7/8"
Nut 5/16"-18
©
Lock Washer 5/16"
17
',
Screws
5/16"xl-7/8"
Installation
Step 6
Install the Deluxe Lighted
Console Wall Control
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
• Strip 1/4" of insulation from one end of the bell
wire; connect the wire to the two screw terminals
on the back of the Wall Control: white to 2, and
white/red to 1.
Install the Wall Control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted,
you can see it
clearly, and there are no obstructions to door
travel.
• Locate the Wall Control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all
moving parts of the door and door hardware.
Fasten the Wall Control securely with 6ABxl"
screws. If installing into drywall, drill 5/32" holes
and use the anchors provided.
• Run the bell wire up the wall and across the ceiling
to the opener. Use insulated staples to secure the
wire in several places. Be careful not to pierce the
wire with a staple, thereby resulting in a short.
Do NOT connect the power and operate the
opener at this time. The trolley will travel to the
full open position but will not return to the close
position until the sensor beam is connected and
properly aligned.
• Receiver terminal screws and the antenna are
located on the right side panel of the opener.
Position the antenna wire as shown.
• Then connect the bell wire to the opener terminal
screws: white to 2; white/red to 1.
See Safety Reversing Sensor Instructions
beginning on page 21.
• Remember to affix the User Safety Instruction
label to the wall near the Wall Control, and the
Maintenance instruction label in a prominent
location on the inside of the garage door,
Page 32 explains how to operate the opener using
the lighted push bar and the Lock & Light features
available on the Deluxe Lighted Console Wall
Control.
If the label adhesive will not adhere to your garage
wall surface (or becomes loose with time) use tacks
to secure the label alongside the Wall Control.
Outdoor Key Switch Accessory Connections
Hardware Shown Actual Size
6ABxl"
Dry Wall Anchors
To opener terminal screws: white to 2; white/red to 1
Insulated
Staples
Opener
Terminal Screws
©©
©
Wall Control
Terminal Screws
Lighted
Push Bar
18
Installation
I
Step 7
Install the Lights and the Lenses
Install the lights:
• Install a 75 watt maximum light bulb in each
socket. The lights will turn ON and remain lit for
approximately 4-1/2 minutes when power is
connected. Then the lights will turn OFF.
75WattMax
Lens
_
Light Bulb
Tab
Lens
Guide
• If the bulbs burn out prematurely due to vibration,
replace them with standard neck "Garage Door
Opener" bulbs.
Lens
.... Stot
Install the lenses:
Lens
Tab
• Apply slight pressure on the sides of each lens
and slide the tabs into the slots in the side panels.
• For convenience, the lenses may be installed
after Adjustment Step 4 on page 30.
Lens _
Tab
• Reverse the procedure to remove the lenses.
Installation
Step 8
Attach the Emergency
Release Rope and Handle
Do not use the red handle to pull the door
open or closed. The rope knot could become
untied and you could fall. Use the emergency
release only to disengage the trolley and, if
possible, only when the door is closed.
Garage doors are heavy. If the door is open
when the handle is pulled, the door could
close inadvertently
if it is not properly
balanced. Serious injury may result to persons
under the door. Make sure the doorway is clear
of persons and obstructions
before pulling
handle when door is open.
Tro,
°v£h° nd
Rope
_
Overhand
Knot
• Thread one end of the rope through the hole in the
top of the red handle so "NOTICE" reads right side
up as shown. Secure with an overhand knot.
The knot should be at least 1" from the end of the
rope to prevent slipping.
Release Arm
_
Emergency
Release Handle
• Thread the other end of the rope through the hole in
the release arm of the outer trolley.
)
• Adjust rope length so the handle is 6 feet above the
floor. Secure with an overhand knot.
If it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.
19
Installation
Electrical
Step 9
Requirements
To prevent electrocution
or fire, installation
and wiring must be in compliance with local
electrical and building codes.
Do NOT use an extension cord, 2-wire adapter,
or change the plug in any way to make it fit
your outlet.
To reduce the risk of electric shock, your garage
door opener has a grounding type plug with a third
grounding pin. This plug will onlyfit into a grounding
type outlet.
If the plug doesn't fit into the outlet you have,
contact a qualified electrician to install the proper
outlet.
To avoid installation difficulties,
do not run the opener at this time.
Right
If permanent
wiring is required
Wrong
by your local code, refer to the following
procedure:
Permanent
Wiring
Connections
To make a permanent connection through the
7/8" diameter hole in the top of the opener
(according to local code):
Ground Tab
• Remove the opener cover screws and set the
cover aside.
Green
Ground
Screw
• Remove the attached 3-prong cord.
• Connect the black (line) wire to the screw on the
brass terminal; the white (neutral) wire to the
screw on the silver terminal; and the ground wire
to the green ground screw. The opener must be
grounded.
• Reinstall the cover.
Black
Wire
Wire
White Wire
To avoid installation difficulties,
do not run the opener at this time.
2O
Black
Wire
The Safety Reversing System
Information
you'll need before you begin the installation
The safety reversing sensor must be connected
and aligned correctly before the garage door
opener will move in the down direction. This is a
required safety device and cannot be disabled.
of the safety reversing
sensor.
Without a properly working safety reversing
sensor, persons (particularly children) could
be injured or killed by a closing garage door.
Read and follow all instructions,
Installation procedures are the same for sectional
and one-piece doors.
To protect small children, install the safety
reversing sensor so that the beam will be no
higher than 4"-6" above the garage floor.
Disconnect power to the garage door opener
before installing the safety reversing sensor.
Be sure power to the opener is disconnected.
The brackets must be securely fastened to a solid
surface such as the studs on either side of the door,
or add a piece of wood at each location if installing in
masonry construction.
The sending eye transmits an invisible light beam to
the receiving eye. The units can be installed on
either side of the garage door as long as the sun
never shines directly into the receiving eye lens.
Look at the label on the connector end of each case
to identify the sensors.
The brackets must be connected and fastened so
that the sending and receiving eyes face each other
as shown in Figure 1.
The invisible light beam path must be unobstructed.
No part of the garage door (or door tracks, springs,
hinges, rollers or other hardware) can interrupt the
beam while the door is closing. If it does, use a piece
of wood to build out each sensor mounting location to
the minimum depth required for light beam clearance.
If an obstruction breaks the light beam while the
garage door is closing, the door will stop and
reverse to full open position and the opener lights
will flash for 5 seconds.
Sensor Beam
4-6" max
above floor
Sensor Beam
4-6" max.
above floor
Invisible Light Beam
Protection Area
Figure 1: Facing the door from inside the garage
21
Installation
install
Step 10
the Safety Reversing
Sensor
Figure 2
Figures 2 and 3 show assembly of brackets and
"C" wrap based on the recommended installation of
the sensors as shown on page 21.
Mounting Bracket
With Square Holes
/
However, Figures 4 and 5 are variations which may
fit your installation requirements better. Make sure
the wraps and brackets are aligned so the
sensors will face each other across the garage
door.
"C" Wrap
#10-32
Lock Nuts
#10-32x3/8"
Screws
• Fasten the "C" wraps to the mounting brackets
having square holes, using the hardware shown
in Figure 2.
• Connect each assembly to a slotted bracket, using
the hardware shown in Figure 3.
Note the alignment of the brackets
right sides of the door.
Figure 3
for left and
1/4x1-1/2"
• Finger tighten the lock nuts.
1/4-20xl/2" Carriage Bolts
(with square shoulder)
Lag Screws
Inside
Garage -Wa
• Use bracket mounting holes as a template to
locate and drill (2) 3/16" diameter pilot holes on
both sides of the garage door, 4"-6" above the
floor but not exceeding 6". (See warning on
page 21 .)
• Attach bracket assemblies with 1/4"x1-1/2" lag
screws as shown in Figure 3.
g Bracket
,vith Slot
• Adjust right and left side bracket assemblies to the
same distance out from the mounting surface.
Make sure all door hardware obstructions are
cleared. Tighten the nuts securely.
/1/4
/
//
_
"C" Wrap
Mounting
Bracket
%
20
Lock Nuts
_otes
Hardware Shown Actual Size
©
#10-32x3/8"
Screw
_
©
I I I I I I I Ill/[Ix!_11!I,I I I I I I I_'_
#10x32
Lock Nut
Lag Screw
1/4"-20x 1/2"
Carriage Botts
Staples
1/4"-20
Lock Nut
Figure 5
Alternate
Wall Mount
Alternate Floor Mount
Inside
Garage
Wail
I
sensor
Indicator Light
Mounting Bracket
with Slot
Mounting Bracket
with Square HoIes
Mounting Bracket
with Square Holes
j/J
,C!' Wrap
Sensor
Mounting Bracket
with Slot
Attach with
anchors
(net provided)
Indicator Light
Garage
Ftoor
Garage
Ftoor
22
• Insertthewireconnectorintoeach
sensorandpushuntilyouheara
click,Figure6.Thewhitetabonthe
sensorshouldbeflushwiththeback
oftheconnector.
Figure 6
Safety Sensor
<
_
Tab
J
I
shoutd
be
flush with back
onnector
/
Push connector
Wire Connector
"
in
until you hear a click
Figure 7
Connect Wire to
Opener Terminals
BelI Wire
__
Finished
__
o._.--"_
Cei,ing
"__
..........
_
Sensor
Connections
Betl Wire
OPENER
TERMINAL
SCREWS
• Center each sensor unit in a "C" wrap with lenses
pointing toward each other across the door.
• Secure sensors with the hardware shown. Finger
tighten the wing nut on the receiving eye to allow
for final adjustment. Securely tighten the sending
eye wing nut.
Wing Nut
"C"
j.Wire
Indicator Light
/
Sensor
Invisible Light Beam
Protection Area
Sensor
Sensor
1/4-20x 1- 1/2"
Hex Bo(t
Trouble Shooting
• Run paired wires from both sensors to the opener.
Use insulated staples to secure wire to wall and
ceiling.
1. If the sending eye indicator light does not glow
steadily after installation, check for:
• Strip 1/4" of insulation from each set of wires.
Separate white and white/black wires sufficiently to
connect to the opener terminal screws: white to 2
and white/black to 3.
• Electric power to the opener.
• A short in the white or white/black wires. These
can occur under staples or at screw terminal
connections.
• Plug in the opener. Make sure the Lock Feature is
off. Green indicator lights in both the sending and
receiving eyes will glow steadily if wiring
connections and alignment are correct.
• Incorrect wiring between sensors and opener.
• An open wire (wire break).
2. If the sending eye indicator light glows steadily but
the receiving eye indicator light doesn't:
If the indicator light is offin the receiving eye (and
the invisible light beam path is not obstructed),
alignment is required.
• Check alignment.
• Check for an open wire to the receiving eye.
• Loosen the receiving eye wing nut to allow slight
rotation of unit. Adjust sensor vertically and/or
horizontally until the green indicator light glows
with a steady lighL
Hardware Shown Actual Size
1/4-20x 1-1/2"
Hex Bott
• When indicator lights are glowing steadily in both
units, tighten the wing nut in the receiving eye unit.
23
Installation
Step 11
Fasten Door Bracket
To prevent
damage
to steel, aluminum,
fiberglass
or glass panel doors, always
reinforce the inside of the door both vertically
and horizontally with an angle iron.
Follow instructions which apply to your door
type as illustrated below or on page 25.
A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should
cover the height of the top panel.
The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of
angle iron are used to create a "U"-shaped support. The best solution is to check with your garage door
manufacturer for an opener installation door reinforcement kit.
/
Header
Bracket
reinforcement
is needed for lightweight garage doors
(fiberglass, aluminum, steel,
doors with glass paeet, etc).
Figure 1
Door
\
Bracket
Lock Washer
5/16"
Location
Carriage BoIt
5/16"-18x2-1/2"
Door
Bracket
j_
Nut/
Vertical _
Guideline
5/16"-18
Figure 2
Inside Ed(
of Door or
Reinforcement Board
Door
• Center the door bracket on the previously marked
vertical guideline used for the header bracket
installation.
Door Bracket
Plate
• Position the bracket on the face of the door within
the following limits:
A) The top edge of the bracket 2"-4" below the top
edge of the door.
Hardware Shown Actual Size
©
B) The top edge of the bracket directly below any
structural support across the top of the door.
• Mark and drill 5/16" left and right fastening holes.
Secure the bracket as shown in Figure 1 if there is
vertical reinforcement.
Nut 5/16-18
If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes
for the door bracket, position the door plate over the
door bracket as shown in Figure 2. Fasten securely
with hardware shown in Figure 11
©
Lock Washer 5/16"
Carriage Bolt
5/16"-18x2-1/2"
24
Please read and comply with the warnings
They apply to one-piece doors also.
Header Wall
and reinforcement
instructions
on page 24.
- Finished Ceiling 2x4 Support
Header
Bracket
Door
Bracket
HodzontaI and vertical
reinforcement is needed for
lightweight garage doors
(fibergIass, aluminum, steel,
door with glass paneI, etc.)
OptionaI
PIacement
of Door
Bracket
VerticaI
Garage Door
For a
exposed framing or for
theo_on,
use_
screw (not supplied) to
fasten door bracket
_
_
v
±
..............
_C_aS,
riage_B°]t,,
,_
5/16"-18x2-1/2"/
"_
/
_
• Center the bracket on the top of the door, in line
with the header bracket as shown. Mark holes.
Hardware Shown Actual Size
• Drill 5/16" pilot holes and fasten the door bracket
with hardware supplied.
©
If the door has no exposed framing, drill 3/16" pilot
holes and fasten the bracket with 5/16"x1-1/2" lag
screws (not supplied) to the top of the door.
Nut 5/16%18
The door bracket may be installed on the top
edge of the door if required for your installation.
(Refer to the dotted line optional placement
drawing.) Drill 3/16" pilot holes and substitute
5/16"x1-1/2" lag screws (not supplied) to fasten
the bracket to the door.
©
Lock Washer 5/16"
Carriage Bolt
5/16"-18x2-1/2"
25
/
/
Installation
Connect
Step 12
Door Arm to Trolley
Follow instructions which apply to your door
type as illustrated below and on page 27.
Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley
from the inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in
Figures 1, 2 and 3.
Figure 1:
Figure 2:
• Fasten straight door arm section to outer trolley
with a clevis pin. Secure the connection with a ring
fastener.
• Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far
apart as possible to increase door arm rigidity.
• Fasten curved door arm to the door bracket in the
same way as shown.
Inner Trolley
/ /
/ /
Lock
Washers
II
I_
R°pe
5/16"//
EmergenNuts "'_._ _
Rsitg e r
lil
I_
_/85/ 16"- 1 8 "'_
Door
Clevis P,n _
_
t"_f_
Z'Jk
ReleasCY
Pin
B
._
/t¢,_/
/_L-
_5
/lS c!18x7
----Handle
/
Straight
Figure
DCUrr\Ard
Figure 2
1
Hole Alignment
Alternative
Figure 3:
• If holes in curved arm are above holes in straight
arm, disconnect straight arm. Cut about 6" from
the solid end. Reconnect to trolley with cut end
down as shown.
• Bring arm sections together.
• Find two pairs of holes that line up and join with
screws, lock washers and nuts.
Hardware Shown Actual Size
©o
Nut 5/16%18
Lock Washer
5/16"
Screws
5/16"-18x7/8"
Ring Fastener
O,,,,,,,,,,Dol
Hex Screw
5/16"-18x7/8"
Figure 3
Clevis Pin
5/16"xl"
Proceed to Adjustment Step 1, page 28. Trolley will re-engage automatically when the opener is operated.
26
Door
Bracket
Assemble the Door Arm:
Ring
• Fasten the straight and curved door arm sections
together to the longest possible length, with a 2 or
3 hole overlap.
• With the door closed, connect the straight door
arm section to the door bracket with a clevis pin.
• Secure with a ring fastener.
5/16"-18x7/8
Curved
Door Arm
On one-piece doors, before connecting the door arm to the trolley the travel limits must be adjusted. Limit adjustment screws are located on the left side panel as shown on page 28. Follow adjustment procedures below.
Fully Closed
Trotley
Fully Open
Trolley
I I
I I
I I
\
\
Door Arm
Connector Hole
I
I
I
I
II
!
Closed
Door
Open Door
Adjustment
Door with
Backward Slant
Procedures
Open Door Adjustment:
Decrease UP limit
Door Arm
for One-Piece
Doors
Closed Door Adjustment:
Decrease DOWN limit
• Turn the UP limit adjustment screw counterclockwise 5-1/2 turns.
• Turn the DOWN limit adjustment screw clockwise
5 complete turns.
• Press the Wall Control push bar. The trolley will
travel to the fully open position.
• Press the Wall Control push bar. The trolley will
travel to the fully closed position.
• Manually raise the door to the open position
(parallel to the floor), and lift the door arm to the
trolley. The arm should touch the trolley just in
back of the door arm connector hole. Refer to the
fully open trolley/door arm positions in the
illustration. If the arm does not extend far enough,
adjust the limit further. One full turn equals 2" of
trolley travel.
• Manually close the door and lift the door arm to the
trolley. The arm should touch the trolley just ahead
of the door arm connector hole. Refer to the fully
closed trolley/door arm positions in the illustration. If
the arm is behind the connector hole, adjust the limit
further. One full turn equals 2" of trolley travel.
Connect
the door arm to the trolley.
• Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may
be necessary to lift the door slightly to make the connection.
• Secure with a ring fastener.
• Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open 3osition
as shown in the illustration, decrease the UP limit until the door is parallel to the floor.
27
Adjustment
Adjustment
Section:
Pages 28 - 30
Step 1
Adjust the UP and DOWN
Limits
Do not make any limit adjustments until the
safety reversing sensors are completely
installed.
Improper adjustment of the travel limits will
interfere
with the proper operation
of the
safety reverse system. The door might not
reverse properly
when required and could
seriously injure or kill someone under it. Test
the safety
reverse
system
following
all
adjustments to the travel limits. See page 30.
Limit adjustment settings regulate the points at
which the door will stop when moving up or down.
The door will stop in the up direction if anything
interferes with door travel. The door will reverse in
the down direction if anything interferes with the
door travel (including binding or unbalanced doors).
000
Left Side Panel
To operate the opener, press the Wall Control push
bar. Run the opener through a complete travel
cycle.
• Does the door open and close completely?
\\
\
• Does the door stay closed and not reverse
unintentionally when fully closed?
\\
If your door passes both of these tests, no limit
adjustments are necessary.
LimitAdjustment
Screws
INCREASE
DOWN
UP
TRAVEL
TRAVEL
Adjustment
Labet
Adjustment procedures are outlined below. Run the opener through a complete travel cycle after each
adjustment.
Repeated operation of the opener during adjustment procedures may cause the motor to overheat and
shut off. Simply wait 15 minutes and try again.
Read the procedures carefully before proceeding to Adjustment Step 2. Use a screwdriver to make limit
adjustments.
How and When
to Adjust the Limits
If the door does not open completely
but opens at leastfive feet
If the opener reverses in fully closed position
Decrease down travel. Turn the DOWN limit
adjustment screw clockwise. One turn equals 2" of
travel.
Increase up travel. Turn the UP limit adjustment
screw clockwise. One turn equals 2" of travel.
If door does not open at least 5 feet: Adjust the
UP (open) force as explained in Adjustment Step 2.
If the door reverses when closing and
there is no visible interference to travel cycle
If the door does not close completely
Increase down travel. Turn the DOWN limit
adjustment screw counterclockwise. One turn
equals 2" of travel.
If the opener lights are flashing, the Safety Reversing
Sensor is obstructed. Remove the obstruction.
Test the door for binding: Pull the emergency
handle. Manually open and close the door. If
is binding, call for garage door service. If the
not binding or unbalanced, adjust the DOWN
force. See Adjustment Step 2.
If door still won't close completely, try lengthening
the door arm. (See Page 26.)
If you have adjusted the door arm to the maximum
length and the door still will not close completely,
lower the header bracket. See Installation Step 1,
pages 12and 13.
28
release
the door
door is
(close)
Adjustment
Adjust
Step 2
the Force
Too much force on the door will interfere with
the proper operation of the safety reverse
system. The door might not reverse properly
when required and could seriously injure or
kill someone under it. Do not increase the
force beyond the minimum amount required
to close the door. Do not use the force
adjustments to compensate for a binding or
sticking garage door. Test the safety reverse
system following
all adjustments
to force
levels. See page 30.
Force adjustment controls are located on the right
side panel of the opener. Force adjustment settings
regulate the amount of power required to open and
close the door.
The door will stop in the up direction if anything
interferes with its travel. The door will reverse in the
down direction if anything interferes with its travel
(including binding or unbalanced doors).
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down
direction and stops in the up direction. Weather
conditions can affect the door movement, so
occasional adjustment may be needed.
Force Adjustment
Controls
The maximum force adjustment range is 260 degrees,
about 3/4 of a complete turn. Do not force controls
beyond that point. Turn force adjustment controls
with a screwdriver.
000
Right Side Panel
Adjustment
Label
How and When to Adjust the Forces
Test the DOWN (close) force
Make 10 degree turn adjustments until the door stops
easily. After each adjustment, run the opener through
a complete travel cycle.
Grasp the door bottom when the door is about
halfway through DOWN (close) travel. The door
should reverse. Reversal halfway through down
travel does not guarantee reversal on a two-inch
obstruction. See page 30. If the door is hard to
hold or doesn't reverse, decrease the DOWN (close)
force by turning the control counterclockwise.
If the door doesn't open at least 5 feet
Increase UP (Open) force by turning the control
clockwise. Make 10 degree turn adjustments until
door opens completely. Re-adjust the UP limit if
necessary. After each adjustment, run the opener
through a complete travel cycle.
Make 10 degree turn adjustments until the door
reverses normally. After each adjustment, run the
opener through a complete cycle.
If the door reverses during the down (close) cycle
and the opener lights aren't flashing
Test the UP (open) force
Increase DOWN (close) force by turning the control
clockwise. Make 10 degree turn adjustments until the
door completes a close cycle. After each adjustment,
run the opener through a complete travel cycle. Do
not increase the force beyond the minimum
amount required to close the door.
Grasp the door bottom when the door is about
halfway through UP (open) travel. The door should
stop. If the door is hard to hold or doesn't stop,
decrease UP (open) force by turning the control
counterclockwise.
29
Adjustment
Step 3
Test The Safety Reversing
Sensor
Without a properly working safety reversing
sensor, persons (particularly children) could be
seriously injured or killed if trapped by a closing
garage door. Repeat this test once a month,
• Press the remote control push button to open the
door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the
door. The door will not move more than an inch,
and the opener light(s) will flash.
Professional service is required if the opener
closes the door when the safety reversing
sensor is obstructed.
The garage door opener will not close from a
remote control if the indicator light in either
sensor is off(alerting you to the fact that the
sensor is misaligned or obstructed).
The garage door can be closed by pressing and
holding the Wall Control push bar until down travel
is completed.
Adjustment
Safety Reversing Sensor
Safety Reversing
Sensor
Step 4
Test the Safety Reverse
System
Failure to test and adjust the safety reverse
system may result in serious injury or death to
persons trapped by a closing garage door.
Repeat this test once a month and adjust as
needed.
Test:
• Place a one-inch board (or a 2x4 laid flat) on the
floor, centered under the garage door.
GARAGE
DOOR
h
• Operate the door in the down direction. The door
must reverse on striking the obstruction.
Adjustment:
If the door stops on the obstruction, it is not traveling
far enough in the down direction.
• Increase the DOWN limit by turning the DOWN
limit adjustment screw counterclockwise 1/4 turn.
• Repeat the test.
_
j
On a sectional door, make sure limit
adjustments do not force the door arm beyond a
straight up and down position. See the
illustration on page 26.
• When the door reverses on the one-inch board,
remove the obstruction and run the opener through
3 or 4 complete travel cycles to test adjustment.
Important
If the door will not reverse after repeated
adjustment attempts, call for professional
garage door service.
safety check
Repeat Adjustment Steps 1, 2 and 4 after:
• Each adjustment of door arm length, force controls
or limit controls.
• Any repair to or adjustment of the garage door
(including springs and hardware).
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
30
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Do not permit children either to operate or to play with the opener. Keep remote control in a
location inaccessible to children.
3. Operate opener only when the door is in full view and free from any obstruction. Keep the door in
sight until it is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
4. Check safety reversal system monthly. See page 30. The garage door MUST reverse on contact
with a one-inch (or a 2x4 board laid fiat) object placed on the floor. If an adjustment is made to
either the force or the limit of travel, both adjustments may be needed and the safety reversal
system must be checked. Failure to properly adjust the opener may result in severe injury or death.
5. If possible, use the emergency release only when the door is in a closed position. Caution should
be taken whenever the disconnect cord is actuated with the door open. Weak or broken springs
may cause the door to fall rapidly, causing injury or death to persons.
6. KEEP GARAGE DOORS PROPERLY BALANCED. See page 3. An improperly balanced door may not
reverse when required and could result in severe injury or death. Repairs to cables, spring
assemblies and other hardware must be made by a professional garage door person.
7. Disconnect the electric power to the garage door opener before making any repairs or removing the
covers.
8.SAVE THESE INSTRUCTIONS.
Care of Your Opener
The remote control
Limit and force adjustment controls
Limit Controls
The opener must learn the code of any new remote
control. Page 33 explains how to program your
receiver and how to erase all codes if required. Self
service of your receiver is not recommended. If
service is needed, contact your nearest Sears
Service Center.
Force Controls
Adjustment Label
(Located on the teft side panel)
Adjustment Labet
(Located on the right side panel)
The remote control battery
Weather conditions may cause some minor
changes in door operation requiring some readjustments, particularly during the first year of
operation.
The green test light should glow and the opener
should operate when the remote control is activated.
If the green test light is dim or does not come on,
replace the battery.
Pages 28 and 29 refer to the limit and force
adjustments. Only a screwdriver is required. Follow
the instructions carefully.
The 12 Volt battery should produce power for at least
a year.
Dispose of your old battery properly.
Repeat the safety reverse test (page 30) after any
adjustment of limits or force.
Maintenance
Once a Month
Schedule
Twice a Year
Manually operate door. If it is unbalanced or
binding, call for professional garage door service.
Check chain tension. Disconnect trolley first.
Adjust if necessary (See page 11 ).
Once a Year
Check to be sure door opens & closes fully.
Adjust limits and/or force if necessary.
(See pages 28 and 29.)
Oil door rollers, bearings
and hinges
The opener does not require additional
lubrication.
Repeat the safety reverse test. Make any
necessary adjustments (See page 30).
Do not grease the door tracks.
31
Operation of Your Opener
Activate the opener with any of the following
devices:
1. The 3-Function Remote control. Hold large push
button down until the door starts to move.
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage.
If possible,
use the emergency
release rope and handle only when the door is
fully closed.
2. The Wall Control. Hold push bar down until the
door starts to move.
3. The Key Switch or Keyless Entry.
When the Opener is Activated:
1. tf open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
To open the door
manually:
The door should be
fully closed if possible.
Pull down on the red
emergency release
handle and lift the door
manually. To
reconnect the door to
the opener, press the
Wall Control push bar.
3. If opening, the door will stop (allowing space for
entry and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
ease Arm
5. If obstructed while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
7. The garage door will reverse in the closing cycle
when the invisible beam is broken. If fully open, the
door will not close when the beam is broken. The
sensor has no effect in the opening cycle.
Emergency
ReIease Handte
(Pull Down)
Manual disconnect
position
If the sensor is not installed, or not aligned correctly,
the door can't close from any portable remote control.
It can be closed with the Wall Control, the Key
Switch, or the Keyless Entry, however, by pressing
and holding the push bar until down travel is
complete. If you release the push bar too soon, the
door will reverse.
The lockout feature
prevents the trolley from
Pull
the emergency
handle
reconnecting
automatically.
down and back (toward the
opener). The door can then
be raised and lowered
manually as often as
necessary. To disengage
the Lockout Feature, pull
the emergency handle
straight down. The trolley
will reconnect on the next
UP or Down operation.
Opener Lights will turn on under the following
conditions: When the opener is initially plugged in;
when the power is interrupted; when the opener is
activated. They will turn off automatically after 4-1/2
minutes or provide constant light when the Light
feature is activated. Bulb size is 75 watts maximum.
Operation
I"- '"'1F_-_7"--
Tro_Fe
Iease Arm
The opener lights will blink for 5 seconds when the
safety reversing sensor causes the door to reverse.
Lighted
__
__
Tro;ley
/_ _
y
Emergency
ReIease Handte
(Pall Down & Back
Towards Opener)
Lockout position
of the Deluxe Lighted Console Wall Control
Lock Feature
Push Bar
Press to open or close the door.
The Lock feature is designed to prevent operation of
the door from portable remote controls. However, the
door will open and closefrom the Wall Control push
bar, the Key Switch and the Multi-Function Keyless
Entry.
To Activate:
Press again to reverse the door during the closing
cycle or to stop the door while it's opening.
Light Feature
Press the Light button. If the opener lights are off,
they will turn on.
Press and hold the Lock button for 2 seconds. The
push bar light will flash as long as the Lock feature
is on.
If the opener lights are on, (even in the 4-1/2 minute
automatic cycle) they will turn off.
But if you use the Light button to turn the lights on
and then activate the opener, the lights will turn off
after 4-1/2 minutes.
To turn off:
Press and hold the Lock button again for
2 seconds.The push bar light will stop flashing.
Normal operation will resume. The Lock feature will
also turn off whenever the "SRT" button on the
opener end panel is activated.
The Light button will not control the opener lights
when the door is in motion.
32
Receiver and Remote Control Programming
To comply with FCC rules, adjustment or modifications
of this receiver]
and/or transmitter are prohibited, except for changing the code setting or I
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE|
PARTS.
J
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death. Do not allow children
to operate the wall push button(s) or remote
control(s).
A moving garage door could injure or kill
someone under it. Activate the opener only
when you can see the door clearly, it is free of
obstructions, and is properly adjusted.
Your 53000SRT series garage door opener (with
receiver "SRT" button) has been factory set to
operate with the large push button on the remote
control(s). However, you can use either of the two
small buttons, if you prefer. And, the 3-function
remote control(s) can also activate additional
garage door openers and/or light controls.
Below are instructions for programming your opener
to match the other buttons on your remote controls
and any additional remote controls you may
3urchase. See available accessories on page 38.
53000SRT
Series Garage Door Openers
(With "SRT" Button)
Figure 1
Mini 3-Function
Remote Control
Your "SRT" garage door opener will operate with as
many as four "SRT" portable remote controls and
one Multi-Function Keyless Entry.
Select a remote controt push
button to operate opener
To Add A Remote Control
1. Select a remote control push button to operate
the receiver.
2. Press and hold the selected remote control push
button, Figure 1.
3. Then press and release the "SRT" button on the
right side panel of the opener in Figure 2. The
opener light will flash once.
Standard 3-Function
Now the opener will operate when the remote
control push button is pressed.
Remote Control
Garage Door Opener
(With "Smart" Button)
If you release the remote control push button
before the opener light flashes, the opener will
not accept the code.
©
©
To Change the Selected Push Button
On the Same Remote control
If you decide to use a different remote control button
than originally programmed into the opener, you
must erase all the learned codes and reprogram
each remote control used to operate the garage
door opener.
To Erase All Remote control Codes
• Press and hold the "SRT" button on the opener
panel until the indicator light turns off (about 6
seconds). AIIthe codes the opener has learned
will be erased.
"SRT"
Button
• To reprogram, repeat Steps 1,2 and 3 for each
remote control in use.
Indicator
Light
END PANEL
Code programming instructions are also located
on the opener panel.
33
Figure 2
Having a Problem?
Situation
Probable
Cause and Solution
The opener doesn't
operate from either
the Wall Control or
the remote control:
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light,
check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.)
2. Have you disabled all door locks? Review installation instruction warnings on Page 11.
3. Is there a build-up of ice or snow under the door? The door may be frozen to the
ground. Remove any restriction.
4. The garage door spring may be broken. Have it replaced.
5. Repeated operation may have tripped the overload protector in the motor. Wait
15 minutes. Try again.
Opener operates
from the remote
control, but not from
the Wall Control:
1. Is the Wall Control lit? If not, remove the bell wire from the opener terminal screws.
Short the red and white terminals by touching both terminals at the same time with a
piece of wire. If the opener runs, check for a faulty wire connection at the Wall
Control, a short under the staples, or a broken wire.
2. Are the wiring connections correct? Review Step 6, page 18.
The door operates
from the Wall Control,
but not from the
remote control:
1. If your model has the Lock feature, make sure the lock is Off.
2. Is any wall push button flashing? Your opener needs to re-learn a remote control
code. Refer to Instructions on the opener panel.
3. Does the battery test light glow when the remote control push button is pressed? If
not, replace the battery.
4. Program the receiver to match the remote control code.
5. Repeat the receiver programming procedure with all remote controls.
The remote control
has short range:
1. Check the battery test light. If the light is dim, replace the battery.
2. Change the location of the remote control in your car.
3. Check to be sure the antenna on the side or back panel of opener extends fully
downward.
4. Some installations may have shorter range due to a metal door, foil backed
insulation, or metal garage siding.
Opener noise is
disturbing in living
quarters of home:
If operational noise is a problem because of proximity of the opener to the living
quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to
minimize vibration to the house and is easy to install.
The garage door
opens and closes
by itself:
Be sure that all remote control push buttons and battery indicator lights are off.
2. Remove the bell wire from the Wall Control terminals and operate from the remote
control only. If this solves the problem, the Wall Control is faulty (replace), or there is
an intermittent short on the wire between the Wall Control and the opener.
The door doesn't
open completely:
1. If the door has been working properly but now doesn't open all the way, increase the
up force. See page 29.
2. Is something obstructing the door? Remove the obstruction or repair the door.
.
3. If door opens at least 5 feet, the travel limits may need to be increased. One turn
equals 2 inches of travel. See page 28.
Repeat the safety reverse test after the adjustment is complete.
The door stops but
doesn't close
completely:
Review the travel limits adjustment procedures on page 28.
Repeat the safety reverse test after any adjustment of door arm length, close
force or down limit.
34
Having a Problem? (continued)
Situation
Probable
Cause
& Solution
The door opens but
won't close:
1. If the opener lights blink, check the safety reversing sensor. See page 23.
2. If the opener lights do not blink and it is a new installation, check the down force.
See Adjustment Step 2, page 29. For an existing installation, see below.
Repeat the safety reverse test after the adjustment is complete•
The door reverses for
no apparent reason
and opener lights
don't blink:
1. Is something obstructing the door? Pull the red emergency release handle. Operate
the door manually, tf it is unbalanced or binding, call for professional garage door
service.
2. Clear any ice or snow from the garage floor area where the door closes.
3. Review the force adjustment procedures on page 29.
4. If door reverses in the fully closed position, decrease the travel limits (page 28).
Repeat safety reverse test after adjustments to force or travel limits• The need
for occasional adjustment of the force and limit settings is normal• Weather
conditions in particular can affect door travel•
The door reverses for
no apparent reason
and opener lights
blink for 5 seconds
after reversing:
Check the safety reversing sensor. Remove any obstruction or align the receiving eye.
See page 23.
The openerl_h_:
•.. don't turn on:
Replace the light bulbs (75 watts maximum). Use a standard neck garage door opener
bulb if regular bulb burns out.
•.. don't turn off:
Is the Light feature on? Turn it off.
The opener strains or
maximum force is
needed to operate
door:
The door may be out of balance or the springs are broken. Close the door and use the
emergency release to disconnect the trolley. Open and close the door manually. A properly
balanced door will stay in any point of travel while being supported entirely by its springs. If it
does not, disconnect the opener and call a professional garage door serviceman.Do not
increase the force to operate the opener.
The opener motor
hums briefly, then
won't work:
The garage door springs are broken. See above.
2. If the problem occurs on the first operation of the opener, door may be locked. Disable
the door lock. If the chain was removed and reinstalled, the motor may be out of phase.
Remove the chain; cycle the motor to the down position. Observe the drive sprocket.
When it turns in a clockwise direction and stops in the down position, reinstall the chain.
.
Repeat the safety reverse test after the adjustment is complete•
The opener won't
operate due to
power failure:
1. Use the emergency release to disconnect the trolley. The door can be opened and closed
manually. When the power is restored, press the Wall Control push bar and trolley will
automatically reconnect (unless trolley is in lockout position.) See page 32.
2. The Emergency Key Release accessory (for use on garages with no service door)
disconnects the trolley from outside the garage in case of power failure.
The chain droops
or sags:
It is normal for the chain to droop slightly in the closed door position. Use the
emergency release to disconnect the trolley. If the chain returns to normal height when
the trolley is disengaged and the door reverses on a one-inch board, no adjustments
are needed (see page 11 ).
35
Repair Parts
1
2
3
4
5
6
7
1A995
41A3489
1B3117
183Bl10
83A4
41A3473
41B2616
Master
link kit
Complete
trolley
T-rail - center
assembly
section
T-rail - end section
(each)
Rail grease
Chain
and cable
Cable
pulley
bracket
assembly
NOT SHOWN
41A3534
Installation
KEY
NO.
PART
NO.
1
2
3
4
41A4086-1
41A4166
41A4086A
41A4481
5
6
41A3888
41A3592
7
8
9
10
11
12
13
14
10A14
29C128
41A2828
217A238
12B380
12B374
41A4353
41A4373A
15
16
17
18
19
20
178B35
178B34
12B350
12B484
12B483
12B485
41A4116
114A1903
kit (includes
page 7).
Parts
6
DESCRIPTION
7
Lighted console wall control
Lighted push button wall control
Deluxe lighted wall control
Single-function
remote control housing & screw
only (no circuit board)
3-function
remote control housing & screw only
3-function
compact
remote control
housing & screw only
12V battery
Remote control visor clip
Emergency
rope & handle assy.
2-conductor
bell wire - white & white/red
Door bracket
Door bracket
8
16
plate
Header bracket w/clevis pin & fastener
Safety sensor kit
(receiving and sending eyes)
with 3' 2-conductor
bell wire attached
Curved door arm section
ol
el
Straight door arm section
Hanging brackets
Square hole bracket
"C" wrap bracket
Slotted bracket
18
Installation
hardware
bag (includes
illustrated
on page 7).
Safety sensor hardware
Owner's manual
oi
el
_I
oi
el
_I
NOT SHOWN
41A3535
Rail assembly hardware
hardware
illustrated
on
hardware
el
J
36
Repair Parts
Opener Assembly
Parts
I
7
20
19
18
Brown
Wire
(Down)
Contact
\\[p_
LIMIT SWITCH
ASSEMBLY
Drive_
Gear
. . _ ....
Center Limit
Contact
KEY
NO.
PART
NO.
DESCRIPTION
1
31D380
Sprocket
2
41 C4220A
Gear and sprocket
Complete
with:
Spring
Thrust
cover
assembly
washer
washer
Retaining ring
Bearing plate
41A2817
Line cord
5
6
41C4253
Wire harness
41A4315-6B
Receiver
Complete
assembly
logic board
with:
Logic board
End panel w/all
labels
labels
7
41A4351
End panel w/all
8
175B88
Light socket
Lens
10
30B363
Capacitor-
11
12A373
Capacitor
12
41A3150
Terminal
13
41D3058
Universal
and grease
Roll pins (2)
41B4245
DESCRIPTION
108D46
w/plug
assembly
'_
Yetlow
Wire
1/2HP
bracket
block w/screws
replacement
bracket, bearing
RPM sensor
gear kit w/grease
4
NO.
9
gear
gear w/retainer
Drive/worm
PART
NO.
_r-]/
_
bracket assembly
Complete
with: Motor,
Roll pins (2)
Drive gear and worm
Helical
KEY
(Up)
Contact
14
41A3474
Cover
15
41A2818
Helical
16
41D3452
Limit switch
17
41C4398A
RPM sensor
18
41A2826
Shaft
19
41A2822A
Interrupter
20
41A4352
End panel
motor
&
worm,
assembly,
gear & retainer
w/grease
assembly
assembly
bearing
kit
cup assembly
NOT SHOWN
41A2825
Opener
(includes
a number
37
assembly
hardware
kit
screws not designated
in illustration).
by
Accessories
Sears offers many useful accessories for your garage door opener. They are illustrated below with
Sears model numbers and descriptions.
53702
53759
Emergency Key Release:
3-Function Compact Remote
Control:
Required for a garage with NO
access
53703
door.
With key ring & Velcro fastening
strip.
53773
Outdoor Key Switch:
Opens the garage door automatically
from outside when remote control is
not handy.
53704
Wire-In Light Control:
H
......
ii
8 Foot Rail Extension
53774
To allow an 8 foot door to open fully.
53705
10 Foot Rail Extension:
Door Clearance
53776
%
Brackets:
53779
(For Sectional Doors Only)
Multi-Function
Keyless
Entry:
Enables homeowner to operate
garage door opener from outside
by entering code on specially
designed keyboard.
3-Function Standard Size
Remote control:
Includes visor clip.
Replace top brackets and rollers on
door to reduce height of door travel.
For use when installing opener in
garage with low headroom
clearance.
53714
Plug-In Light Control:
Controls interior lights. Plugs into a
wall receptacle.
To allow a 10 foot door to open fully
53709
Controls interior or exterior lights.
Wires into the electrical box like a
dimmer switch.
Support Bracket:
For finished ceilings or where you require additional support based on garage construction.
Includes bracket and fastening hardware.
38
Index
Chain Tension ..............................................................................................................................................
4, 5, 11
Electrical Safety Warnings ........................................................................................................................
2, 20, 31
Garage Door
Testing for balance, binding and sticking ...................................................................................................
Determining high point of travel:
Sectional door ...................................................................................................................................................
3, 28, 31
One-piece door .................................................................................................................................................
Disabling existing locks ....................................................................................................................................
Door clearance brackets (for garages with low headroom) ..............................................................................
Force controls
Adjustment procedures .................................................................................................................................
Problems that might require force adjustments ..........................................................................................
Safety warnings ..........................................................................................................................................
Door hardware .....................................................................................................................
3, 9, 11, 12, 18,
Maintenance instruction label ........................................................................................................................
Reinforcement requirements ...........................................................................................................................
Removing of all ropes .......................................................................................................................................
Possible door damage ...................................................................................................................................
Travel limits
Adjustment procedures .....................................................................................................................................
Problems that might require limit adjustments ............................................................................................
Safety warnings ..........................................................................................................................................
Manual (Emergency) Release Rope & Handle
Lockout feature ....................................................................................................................................................
Manual disconnect ...............................................................................................................................................
Safety warnings .................................................................................................................................
12
13
3, 11
38
4, 29
34, 35
29, 31
31, 32
11, 28
4, 24
3, 11
16, 24
28
34, 35
28, 31
32
32
11, 19, 31, 32
Opener Terminals
Wall control connections ......................................................................................................................................
Safety reversing sensor connections ...................................................................................................................
Outdoor key switch accessory connections .........................................................................................................
Operational Noise
Sprocket noise .....................................................................................................................................................
Vibration noise (isolator kit) .................................................................................................................................
18
23
18
11
34
Receiver and Remote Control
Programming the receiver ...................................................................................................................................
Erasing all codes .................................................................................................................................................
Activating other openers ......................................................................................................................................
Safety warning .....................................................................................................................................................
Problems with remote control operation ..............................................................................................................
33
33
33
33
34
Safety Reverse Test Procedure ..........................................................................................................................
30
Testing required .................................................................................................................................
11, 30, 34, 35
Safety reverse system problems
Securing header bracket to wall .......................................................................................................................
12
Adjusting travel limits ........................................................................................................................................
28
Applying excessive force on the door ...............................................................................................................
29
Buckling or uneven floor .................................................................................................................................
4, 5
Safety Warnings .........................................................
2, 3, 9, 11, 12, 16, 18, 19, 20, 21,24, 28, 29, 30, 31, 32, 33
User Instruction Label for garage wall ........................................................................................................
39
11, 18
SEARS
I:RRFTSMRN
OWNER'S
MANUAL
GARAGE DOOR OPENER
For the repair or replacement parts you need
Call 7 am - 7 pm, 7 days a week
1-800-366-PART
Model No.
139.53225SRT1
139.53325SRTI
139.53425SRTI
139.53628SRTI
139.53629SRTI
139.53635SRTI
139.53637SRT1
139.53824SRTI
(1-800-366-7278)
For in-home major brand repair service
Call 24 hours a day, 7 days a week
1-8OO-4-REPAIR
(1-800-473-7247)
For the location of a
Sears Repair Service Center in your area
Call 24 hours a day, 7 days a week
1-8OO-488-1222
A
For information on purchasing a Sears
Maintenance Agreement or to inquire
about an existing Agreement
Call 9 am - 5 pm, Monday-Saturday
SEARS
1-8OO-827-6655
The model number
label is located under
America's
the light lens on the
front end panel of
SEARS WARRANTY
FULL 90 DAY WARRANTY ON GARAGE
Repair
Specialists
DOOR OPENER
For 90 days from the date of purchase, Sears wilt repair any defect in material or
workmanship at no charge.
LIMITED WARRANTY
From the 93 st day until one year from the date of purchase, Sears will furnish
rep(acement parts for any defective parts, free of charge. You pay for labor.
LIMITED WARRANTY ON 1/2 HP AND 1/3 HP MOTORS
FOR CRAFTSMAN OPENERS
I/2HP MOTOR: After 1 year and through 5 years, Sears will furnish replacement
parts for any defective parts in motor, free of charge. You pay for labor.
your opener,
When requesting
service or ordering
parts, always provide
the following
information:
I/3HP MOTOR: After 1 year and through 3 years, Sears
parts for any defective parts in motor, free of charge. You
LIMITATION ON LIABILITY
Sears will not be liable for loss or damage to property
consequential
loss or expense from property damage
from the use of this product.
will furnish replacement
pay for labor.
or any incidental or
due directly or indirectly
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty does not cover repairs necessary because of operator abuse or
negligence, including failure to install, adjust and operate the opener according to
instructions contained in the owner's manual,
[] Product Type
[] Model Number
[] Part Number
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST
BEARS STORE OR SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state,
[] Part Description
SEARS
Sears,
114A1903B
Roebuck
and Co.,
@1995,
ROEBUCK AND COMPANY,
Hoffman
All Rights
Estates,
Reserved
IL 60179
Dept. 817WA, Hoffman Estates,
IL 60179
U.S.A.
Printed
in Mexico