Mitsubishi XD70U User manual

DATA PROJECTOR
MODEL
XD70U
User Manual
IMPORTANT
* DLP™ (Digital Light Processing) and DMD (Digital Micromirror Device) are registered trademarks of Texas Instruments Incorporated (U.S.A.).
* DMD is an ultra-precise part developed by Texas Instruments (U.S.A.) which takes the place of liquid crystal (in the
projector).
* VGA and XGA are trademarks or registered trademarks of International Business Machines Corporation (U.S.A.).
* S-VGA is a registered trademark of Video Electronics Standards Association.
* Microsoft, Windows, and PowerPoint are registered trademarks of Microsoft Corporation (U.S.A. and other countries).
* Macintosh is a trademark of Apple Computer Inc. (U.S.A.).
* TMDS is a trademark of Silicon Image, Inc.
Note that even in the absence of explanatory notes, serious attention is paid to the trademarks of the various companies
and to the product trademarks.
XD70
IMPORTANT SAFETY INFORMATION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If
you use another power-supply cord, it may cause
interference with radio and television reception.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN PROJECTOR IS IN THE POWER ON
MODE.
CAUTION
Not for use in a computer room as defined in
the Standard for the Protection of Electronic
Computer/Data Processing Equipment, ANSI/
NFPA 75.
E-1
IMPORTANT SAFETY INFORMATION
CAUTION
Do not look at the laser pointer’s light source.
Be sure to heed the following. Pointing the laser beam at
the eyes could lead to reduced vision or vision impairment.
• Never look at the laser pointer’s light source.
• Do not point the laser beam at people.
• Do not let children use the laser pointer.
This label is located on the side of the remote control.
E-2
IMPORTANT SAFETY INFORMATION
Please read all these instructions regarding your projector
and retain them for future reference. Follow all warnings
and instructions marked on the projector.
1. Read instructions
All the safety and operating instructions should be
read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be retained for future reference.
3. Warnings
All warnings on the appliance and in the operating
instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet before
cleaning it. Do not use liquid aerosol cleaners. Use a
damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk of fire, electric shock or
other personal injury.
7. Water and moisture
Do not use this projector near water or in contact
with water.
8. Accessories
Do not place this projector on an unstable cart, stand,
tripod, bracket or table. Use only with a cart, stand,
tripod bracket, or table recommended by the manufacturer or sold with the projector. Any mounting of
the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved
with care. Quick stops, excessive force and uneven
surfaces may cause the appliance and cart combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided for
ventilation, ensuring reliable operation of the projector and to protect it from overheating. Do not block
these openings or allow them to be blocked by placing the projector on a bed, sofa, rug, or bookcase.
Ensure that there is adequate ventilation and that
the manufacturer's instructions have been adhered
to.
10. Power sources
This projector should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power, please consult
your appliance dealer or local power company.
11. Power-cord protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles, and
points where they exit from the appliance. Do not
put the power cord under a carpet.
12. Overloading
Do not overload wall outlets and extension cords as
this can result in a fire or electric shock.
13. Objects and liquids
Never push objects of any kind through openings of
this projector as they may touch dangerous voltage
points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the
projector.
14. Servicing
Do not attempt to service this projector yourself. Refer all servicing to qualified service personnel.
15. Damage requiring service
Unplug this projector from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
(a) If the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen
into the projector.
(c) If the projector does not operate normally after
you follow the operating instructions. Adjust only
those controls that are covered by the operating
instructions. An improper adjustment of other
controls may result in damage and may often
require extensive work by a qualified technician
to restore the projector to its normal operation.
(d) If the projector has been exposed to rain or water.
(e) If the projector has been dropped or the cabinet
has been damaged.
(f) If the projector exhibits a distinct change in performance - this indicates a need for service.
16. Replacement parts
When replacement parts are required, be sure that
the service technician has used replacement parts
specified by the manufacturer or parts having the
same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock
or other hazards.
17. Safety check
Upon completion of any service or repair to this projector, ask the service technician to perform safety
checks determining that the projector is in a safe
operating condition.
E-3
IMPORTANT SAFETY INFORMATION
WARNING:
Unplug immediately if there is something wrong with
your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric shock.
In this case, unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An inadvertent contact may result in an electric shock. Except
as specifically explained in the Owner's Guide, do not
attempt to service this product yourself. Please contact
your dealer when you want to fix, adjust or inspect the
projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or drop it.
Unplug the projector and contact your dealer for inspection. It may lead to fire if you keep using the equipment.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface only.
Please do not place equipment on unstable surfaces.
Do not look into the lens when it is operating. It may hurt
your eyes.
Never let children look into the lens when it is on.
Do not unplug the projector during operation.
It can lead to lamp breakage, fire, electric shock or other
trouble.
Do not touch Air outlet grille and Bottom plate which
becomes hot.
Do not touch them or put other equipment in front of Air
outlet grille. The heated Air outlet grille and Bottom plate
may cause injury or damage to other equipment. Also,
do not set the projector on the desk which is easily affected by heat.
Do not look into the air outlet grille when projector
is operating.
Heat, dust etc. may blow out of it and hurt your eyes.
Place of installation
For safety’s sake, refrain from setting the projector at
any place subjected to high temperature and high humidity. Please maintain an operating temperature, humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+95°F (+35°C)
• Operating humidity: between 30 and 85%
• Never put any heat-producing device under the projector so that the projector does not overheat.
• Do not attach the projector to a place that is unstable
or subject to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a large
current.
• Place the projector on a solid, vibration free surface:
otherwise it may fall, causing serious injury to a child
or adult, and serious damage to the product.
• Do not stand the projector: it may fall, causing serious
injury and damage to the projector.
• Slanting the projector more than ±10˚(right and left)
or ±15˚ (front and rear) may cause trouble or explosion of the lamp.
• Do not place the projector near air-conditioning unit
or heater to avoid hot air to the exhaust and ventilation hole of the projector.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate the
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
E-4
Major Features
䡵 Lightweight high-intensity projector
The synergy of the DLP™ (Digital Light Processing) display system and our own optical design serve to improve the optical
utilization efficiency. The three primary colors (RGB) required in color expression are reproduced with one DMD (Digital
Micromirror Device of high precision). These factors have enabled a design that offers both high intensity and small size/
lightweight features.
䡵 Sharp, clear picture
The DLP™ display system affords RGB color fidelity and inconspicuous gaps between the individual dots, thereby permitting
the display of small characters and diagrams with distinct clarity.
䡵 Powerful functions for presentations
A wide variety of easy-to-set functions have been built into the projector, from a digital keystone correction function (used
when making settings) that corrects picture distortion, to an auto adjustment function that automatically identifies the PC
signal.
A presentation timer that supports presentations and a security lock function protecting against unauthorized projection have
also been added.
䡵 High contrast ration of 2000:1
Use of a new generation of DMD devices has given birth to an amazing 2000:1 high contrast ratio.
By widening the difference of brightness between black and white, you can see a degree of sharpness that is greater than just
the brightness based on specifications.
䡵 Beautiful reproduction of high-quality images from DVD
Faithful reproduction of color tones gives rise to the display of natural images. High-quality images such as those from DVD
and digital high-definition television broadcasts bring out the display capabilities that are an essential strength of the DLP™
display system projector.
䡵 Lamp-mode switch function for the lamp output
Using the lamp Low-mode will extend the life of the lamp and lower the power consumption.
By switching the lamp mode to suit your operating environment, you will save on lamp cost as well as contribute to energy
conservation and ecology.
E-5
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................................... E-1
Major Features ....................................................................................................................... E-5
Table of Contents ................................................................................................................... E-6
Checking the Supplied Accessories .................................................................................... E-8
Names of the Main Unit Parts ............................................................................................. E-10
Names of the Remote Control Parts/Preparing the Remote Control .............................. E-12
Remote Control Range ............................................................................................. E-13
The Procedure Up to Projecting to the Screen ................................................................. E-14
Placement Guide .................................................................................................................. E-15
Screen Size and Projection Distance ........................................................................ E-15
Connecting Personal Computers and Video Equipment .................................................. E-16
Connections with Personal Computer ....................................................................... E-16
Connect the projector’s RGB connector using the included RGB signal cable. .. E-16
To Output the External Output Signal of a Notebook Computer ......................... E-17
Connections with Composite Signals ........................................................................ E-18
Video Equipment with VIDEO Connectors .......................................................... E-18
Video Equipment with S-VIDEO Connectors ...................................................... E-18
Connections with Component Signals ....................................................................... E-19
When the Video Equipment Has a YCbCr Connector or YPbPr Connector ........ E-19
Connections with the AUDIO Jack ............................................................................ E-20
Power Cable Connections and Switching the Power On/Off ........................................... E-21
Operating ................................................................................................................... E-21
Finishing .................................................................................................................... E-23
Adjustment of the Projection Screen ................................................................................. E-24
Adjustment of the Projection Screen ......................................................................... E-24
Making Adjustments with the Adjusters .............................................................. E-25
General Operation ................................................................................................................ E-26
Input Selection .......................................................................................................... E-26
Automatic Adjustment ............................................................................................... E-26
Selection of Aspect Ratio .......................................................................................... E-27
Freezing a Moving Picture ......................................................................................... E-28
Cancelling Video and Audio Temporarily ................................................................... E-28
Adjustment of the Volume .......................................................................................... E-28
Enlargement of the Image and Video Movement ...................................................... E-29
Using the Presentation Timer .................................................................................... E-30
Using the Laser Pointer ............................................................................................. E-31
Performing Mouse Operations on the Computer
with the Remote Control Unit .................................................................................... E-32
Controlling the Projector from a Computer ................................................................ E-33
Protecting the Projector with the Security Lock ......................................................... E-34
Using the Quick Menu ............................................................................................... E-36
Menu Operation Method ...................................................................................................... E-37
Performing Menu Operations .................................................................................... E-39
List of Item Names Offering Input Selection and Adjustments/Settings .................... E-42
Image ..................................................................................................................................... E-44
Brightness / Contrast / Color / Tint / Sharpness ........................................................ E-44
Picture Adj. / Fine Picture / H Position / V Position .................................................... E-44
Reset ......................................................................................................................... E-45
E-6
Table of Contents
Color ......................................................................................................................................
Quick Color Adj. ........................................................................................................
Gamma .....................................................................................................................
Color Temp. ...............................................................................................................
White .........................................................................................................................
Color Space ..............................................................................................................
White Balance ...........................................................................................................
View .......................................................................................................................................
Aspect .......................................................................................................................
Filter ..........................................................................................................................
Vertical Flip/Horizontal Flip ........................................................................................
Keystone ....................................................................................................................
Keystone Save ..........................................................................................................
Setup .....................................................................................................................................
Auto Source ...............................................................................................................
Auto Power Off ..........................................................................................................
Menu Position ............................................................................................................
Lamp Mode ...............................................................................................................
Input Format ..............................................................................................................
Presentation Timer ....................................................................................................
Option ...................................................................................................................................
Language ..................................................................................................................
On Screen .................................................................................................................
Background ...............................................................................................................
Startup Screen ..........................................................................................................
Security Lock .............................................................................................................
Info. ........................................................................................................................................
Status ........................................................................................................................
Factory Default ..........................................................................................................
Lamp Timer Reset .....................................................................................................
Resolution / Frequency .............................................................................................
Lamp Timer ...............................................................................................................
When an Indicator is Lit or Flashing ..................................................................................
Troubleshooting ...................................................................................................................
Cleaning ................................................................................................................................
Replacing the Lamp Cartridge ............................................................................................
Specifications .......................................................................................................................
Table of Supported Frequency ...........................................................................................
Cabinet Dimensions ............................................................................................................
E-7
E-46
E-46
E-46
E-47
E-47
E-47
E-48
E-49
E-49
E-49
E-50
E-50
E-50
E-51
E-51
E-51
E-52
E-52
E-53
E-53
E-54
E-54
E-54
E-54
E-55
E-55
E-56
E-56
E-56
E-56
E-57
E-57
E-58
E-59
E-60
E-61
E-64
E-65
E-66
Checking the Supplied Accessories
Remove the main unit and the accessories from the box and check that the following items are included.
S-Video cable (Mini DIN 4-pin plug, 2 m / 6.6 feet) [1]
This cable is used in the connection of video equipment that
has an S-video connector. Connections are described on Page
E-18.
No. 777918300
1
U
N
O
E
M
E
ID
S
TA
B
D
N
Y
G
R
B
V
LA
S
E
R
A
TO
U
Q
E
K
IC
U
TE
N
Q
R
FR
EE
ZE
TE
U
M
/
K
L
LIC E
-C C
R AN
C
E
M
TI
L
O
V
R
3
2
M
O
ZO
4
Wireless remote control unit with laser pointer [1] /
Size AAA batteries [2]
This controls the projector. (See Page E-12.)
No. 777998012
RGB signal cable
(Mini D-sub 15-pin, 2 m / 6.6 feet) [1]
This is used in making connections with a personal computer.
See Page E-16 about connections.
No. 777918100
Video cable (RCA pin plug, 2 m / 6.6 feet) [1]
This cable is used in the connection of video equipment that
has a video connector. Connections are described on Page E18.
No. 777918200
Power cable (1.8 m / 5.9 feet) [1]
This power cable supplies power to the unit. See Page E-21
about connections.
No. 777918002 (UL)
Audio cable (Mini plug, 2 m / 6.6 feet) [1]
This cable is used with equipment that has phono type audio
jacks. Connections are described on Page E-20.
No. 777918400
Audio conversion cable (Mini-jack/ RCA pin plug, 15 cm /
0.5 feet) [1]
This cable is used with equipment whose audio connector is
of the phono pin type. Connections are described on Page E20.
No. 777918500
USB cable (type A, 2 m / 6.6 feet) [1]
Used to perform mouse operations on a computer using the
projector’s remote control unit. Connections are described on
Page E-32.
No. 777918600
E-8
Checking the Supplied Accessories
Storage case (for projector and accessories) [1]
This case is designed to hold the projector itself and its
accessories.
Use it when storing the projector.
No. 777919700
HOW TO PUT THE PROJECTOR INTO THE STORAGE CASE
Close the lens shutter or lens cap before putting the projector in its case, then fasten the projector in place with the
Velcro belt. Place the accessories in the storage pocket.
Velcro belt
Pocket
Cable storage pouch [1]
User Manual (CD-ROM edition) [1]
No. 777919101
User Manual (Simplified Edition) [1]
No. 777919001
Security Sheet [1]
No. 777916600
Security Label [1]
No. 777916700
E-9
TA
TU
S
N
TA
S
D
Y
B
S
TA
N
D
B
Y
A
U
TO
S
O
U
R
C
E
Names of the Main Unit Parts
S
Zoom ring [E-24]
Focus ring [E-25]
Exhaust vents
Ventilation slots
Remote control
sensor [E-13]
Adjuster button [E-25]
(Also on opposite side)
Lens
Lens cap
Remove before use. Attach
the lens cap after use to
protect the lens.
Ventilation slots
Lamp cover [E-62]
Adjusters [E-25]
E-10
Names of the Main Unit Parts
STATUS indicator [E-21, 58]
STATUS
STANDBY indicator [E-21, 58]
STANDBY
STANDBY button [E-21]
STANDBY
AUTO button [E-26]
AUTO
SOURCE button [E-26]
SOURCE
Remote control sensor [E-13]
S
TU
TA
S
Y
B
D
N
TA
S
Y
B
D
N
TA
S
TO
U
A
O
S
E
C
B
R
G
U
R
S
E
ID
V
O
AC IN connector [E-21]
O
E
ID
V
IO
D
U
A
E
S
U
O
M
PC
CO
NT
RO
L
Speaker
Built-in security slot
(See description below.)
Ventilation slots
MOUSE connector [E-32]
AUDIO connector [E-20]
RGB
S VIDEO
VIDEO
AUDIO
PC CONTROL
MOUSE
VIDEO connector [E-18]
S-VIDEO connector [E-18]
PC CONTROL connector
(D-Sub 9-pin) [E-33]
RGB connector [E-16, 19]
Built-in Security Slot
This security slot supports the MicroSaver Security System manufactured by
Kensington Microware Inc.
E-11
Names of the Remote Control Parts/Preparing the Remote Control
STANDBY button [E-21, 23]
This button is used to switch ON the
power and set the unit to the
STANDBY mode.
Buttons used for input selection
[E-26]
RGB button and VIDEO button
(VIDEO / S-VIDEO)
Buttons used for menu operations
[E-37]
The , ,
and
buttons are the
select (왖, 왔, 왗 and 왘) buttons.
LASER button [E-31]
(Turns the laser point on and off)
STANDBY
LASER
VIDEO
RGB
AUTO button [E-26]
(Automatic adjustment of the RGB
moving image)
AUTO
MENU
QUICK
QUICK button [E-36]
(Displays a simplified menu)
Q
Buttons used for the PC mouse
function [E-32]
(JOG button and R-CLICK button)
R-CLICK/
CANCEL
ENTER
FREEZE
TIMER button [E-30]
(Presentation timer time setting
display)
MUTE button [E-28]
(Temporarily cancels the video and
audio)
ZOOM button [E-29]
(Digital zoom adjustment)
TIMER
MUTE
FREEZE button [E-28]
(Freezes moving pictures)
VOL button [E-28]
(Volume adjustment)
1
2
VOL
ZOOM
3
4
Infrared transmitter [E-13]
Number buttons [E-34]
(Used for the security lock.)
Laser transmitter [E-31]
L-CLICK button [E-32]
Note:
If a button on the remote control unit is held in continuously for approximately 30 seconds, signal transfer will be suspended. To resume
transferring signals, press the button again.
Also, to use the jog button after signal transfer has been suspended, first press any other button, then press the jog button.
Inserting the Batteries
When using the remote control for the first time, install the batteries that were supplied.
the battery compartment cover (lo1 Slide
cated on the bottom of the remote con-
Leaving a little space in the front, close
3 (A)
the lid, (B) then with the back pressed
trol) and pull off.
tightly, (C) press the lid towards the front.
the polarity (+), (–) of the batteries,
2 Check
and set them correctly, inserting their (–)
(A)
side first.
• If the battery is inserted from the (+) side
first, inserting the (–) side is difficult because
the coil spring end hits on the battery side.
If the battery is forced to insert in this way,
the outer label of the battery may get ripped
and it may cause a short-circuit and heating.
(C)
(B)
* When replacing batteries, purchase two of
the same type of AAA battery.
Caution:
• If the batteries are treated incorrectly, they may cause fire or other contamination due to leakage of the liquid, heating, or they may burst.
(Read the cautions indicated on the battery, too.)
• Do not use a new battery with an old one.
• Load batteries in the correct position.
• Do not heat, take apart, or throw batteries into fire.
• Do not try to racharge batteries. Do not use rechargeable batteries.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes incontact with your eyes, rinse
them with water and then consult your doctor.
E-12
Names of the Remote Control Parts/Preparing the Remote Control
Remote Control Range
Point the infrared transmitter of the remote control toward the remote control sensor located at the front or rear of the main unit
and operate.
Reception of the remote control signal should generally be possible within the range illustrated below.
6m/19.7feet
Side View
Top View
Remote control infrared transmitter
et
.8
fe
/9
3m
30°
30°
30°
Remote control sensor
30°
20°
Remote control infrared transmitter
20°
5m/16.4feet
Remote control sensor
5m/16.4feet
Note:
The range of operation differs according to the usage environment.
Precautions
Handling of the Remote Control
* Do not drop the remote control or handle it inappropriately.
* Do not expose the remote control to water or other liquids. Should the remote control become wet, wipe it dry
immediately.
* Try to avoid use in hot and/or humid locations.
* Please keep button batteries out of the reach of children. If a battery is swallowed, promptly obtain the medical care
of a doctor.
* Remove the batteries from the remote control when it is not going to be used for a long period.
* Some operations (such as menu operations) are available only through the use of the remote control and attention
should be given to its careful handling.
E-13
The Procedure Up to Projecting to the Screen
Perform setup adjustments in the following order.
1 Position the projector
Determine the locations to set up the screen and the projector.
See “Placement Guide” on Page E-15.
2 Connect the video equipment and personal computer
Connect your equipment to the projector.
When making connections with the personal computer’s RGB connector, see “Connections with
Personal Computer” on Page E-16.
When making connections with the video equipment’s video connector or an S-video connector,
see “Connections with Composite Signals” on Page E-18.
When making connections with the video equipment’s YCbCr connector or YPbPr connector,
see “Connections with Component Signals” on Page E-19.
When playing the audio through the built-in speaker of the projector, see “Connections with the
AUDIO Jack” on Page E-20.
3 Opening the lens cap
4 Connecting the power cable and switching on the power
See “Operating” on Page E-21.
See “Finishing” on Page E-23.
5 When selecting the language of menu displays, etc.
(Only when the power is first switched on following purchase)
See “When [Menu Language Select] Is Displayed Upon Switching On the Power” on Page E-22.
6 Switching on the power of the personal computer and video equipment
7 Properly adjust the projection image to the screen
See “Adjustment of the Projection Screen” on Page E-24.
8 Selecting input equipment
See “Input Selection” on Page E-26.
9 Adjust the screen or video image
Adjust the image to the optimum condition as required.
See the Table of Contents for the adjustment items.
About DLP projectors
Though careful attention is paid to providing optimum quality, please note that with DLP type projectors, in rare cases there may
be black spots or bright spots among the picture elements.
Note:
* Please purchase a screen.
* A component cable (Not supplied), which is available separately, is required to connect a DVD player or other equipment with YCbCr
connectors.
* A component cable (Not supplied), which is available separately, is required to connect high definition (HD) video equipment or other
equipment with YPbPr connectors.
E-14
Placement Guide
• Use this information as a guide to find out about the screen size when the projector is placed at a certain location, or
to find out the approximate size of a screen that will be required.
• When suspending the projector from the ceiling, change the projection method. See “Vertical Flip” on E-50.
Screen Size and Projection Distance
• The projection distance over which focussing is adjustable is 1.20 m (3.94 feet) to 9.59 m (31.46 feet). The projector
should be placed within this range.
Screen Size Designation (Inches)
300
"
Height from center of
lens to top edge of
the projection
250
"
200
"
180
"
h1
150
Height from center of
lens to bottom edge
of the projection
"
120
"
100
"
h2
80"
60"
Unit: m (feet)
"
26
9(
26
.5
8–
97
30
–6
6.
64
–7
7.
.9
–9
.7
21
8(
20
.3
17
8(
.3
Width
5.
77
4.
3)
.9
.8
9–
5–
.6
15
3(
.7
–5
8(
.7
–4
3.
97
18
8)
.6
2–
.0
13
.4
10
1(
.8
–3
17
3.
15
.5
12
0–
66
8.
8(
.1
–3
64
2.
0)
43
0.
–1
89
6.
4(
.5
–2
10
2.
)
.3
–8
–6
.15
0(5
1.9
7–
1.5
Lens surface of
the main unit
0)
3)
.23
)
1
(3 .20
.9
4)
.1
.1
8)
5–
31
.4
6)
38.4
Screen size (Diagonal)
Screen Size
Designation (Inches)
Screen Size Width x Height
(m)
(feet)
Projection Distance
(m)
(feet)
Wide – Tele
Height h1
(m)
(feet)
Height h2
(m)
(feet)
Wide – Tele
2.26 0.10
0.33
38.4"
0.78⳯0.59
— – 1.20
— – 3.94 0.69
2.56 ⳯ 1.92
3.54 0.16
0.52
60"
1.22⳯0.91
1.57 – 1.90
5.15 – 6.23 1.08
4.00 ⳯ 3.00
4.69 0.22
0.72
80"
1.63⳯1.22
2.10 – 2.54
6.89 – 8.33 1.43
5.33 ⳯ 4.00
5.87 0.27
0.89
100"
2.03⳯1.52
2.64 – 3.18
8.66 – 10.43 1.79
6.67 ⳯ 5.00
7.05 0.32
1.05
120"
2.44⳯1.83
3.17 – 3.81 10.40 – 12.50 2.15
8.00 ⳯ 6.00
8.83 0.40
1.31
150"
3.05⳯2.29
3.97 – 4.78 13.02 – 15.68 2.69
10.00 ⳯ 7.50
1.61
180"
3.66⳯2.74
4.77 – 5.73 15.65 – 18.80 3.23 10.60 0.49
12.00 ⳯ 9.00
1.77
200"
4.06⳯3.05
5.30 – 6.38 17.39 – 20.93 3.59 11.78 0.54
13.33 ⳯10.00
2.20
250"
5.08⳯3.81
6.64 – 7.98 21.78 – 26.18 4.48 14.70 0.67
16.67 ⳯12.50
2.66
300"
6.10⳯4.57
7.97 – 9.59 26.15 – 31.46 5.38 17.65 0.81
20.00 ⳯15.00
* There is a tolerance of ±5% due to design values.
* This table uses the lens apex and lens center as references and requires that the projector be in a horizontal condition
(with front and rear adjusters fully withdrawn).
E-15
Height
Connecting Personal Computers and Video Equipment
Connecting this unit with a personal computer permits presentation data to be projected as a large screen display at
conferences, lectures, and on other occasions. Furthermore, connecting this unit to a DVD player or other video equipment source in combination with an audio/video amplifier and speaker system will allow you to enjoy convincing home
theater.
Connections with Personal Computer
Please check the following before making connections with the personal computer.
• A suitable resolution for the XD70U is 1024 ⳯ 768 dots (XGA) and the maximum displayable resolution is S-XGA (1280 ⳯
1024 dots).
Make changes to a displayable resolution at the personal computer side. Please check with “Table of Supported Frequency” on
Page E-65.
• The setting method for the personal computer will differ depending on the specific model. Please read the personal computer
instruction manual or the on-line help information, or contact the manufacturer of your personal computer.
Connect the projector’s RGB connector using the included RGB signal cable.
•
•
•
When making connections with the RGB connector of the projector, please make the connection via the supplied RGB signal
cable.
The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “RGB”
using the menu sequence of [Setup] → [Input Format] → [RGB].
See “Input Format” on Page E-53.
If the USB cable is connected to the projector’s MOUSE connector, mouse operations can be performed on the computer from
the projector’s remote control unit.
See “Performing Mouse Operations on the Computer with the Remote Control Unit” on Page E-32.
Note:
* When the input format has been switched, you may be required to reconnect the input signal.
* If the position is off or there are dark vertical bands on the picture, press the AUTO button with the screen as bright as possible (make the
screen as bright as possible by for example displaying the trash window over the entire screen). If the problem persists after pressing the
AUTO button several times, set manually at the “Picture Adjustment” menu.
MONITOR OUT
Personal
computer
RGB signal cable (Supplied item)
Note:
* Before making connections, check the power of the projector and the equipment to be connected is switched off.
* When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook computer
startup procedure as well as the operation that follows startup. Please consult the instruction manual of your notebook computer or the online help.
E-16
Connecting Personal Computers and Video Equipment
To Output the External Output Signal of a Notebook Computer
When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook
computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your
notebook computer or the on-line help while performing the following procedure.
whether a signal is being sent from the notebook computer to the projector.
1 Check
An indication appearing on the liquid crystal display of the notebook computer does not necessarily mean that an external
output signal is being output.
REFERENCE: When “Resolution” or “Frequency” is not displayed under “Info.” on the menu of the projector, this means that
the external output signal is not being output from the personal computer. See “Resolution/Frequency” on Page E-57.
a sign not be output from the notebook computer, please try the operation described below.
2 Should
For an IBM PC/AT compatible computer, press the [Fn] key plus any one of the [F1] to [F10] keys. (See the table below.)
Manufacturer
Model
Key
DELL
All computers
Fn + F8
EPSON
All computers
Fn + F8
FUJITSU
All computers
Fn + F10
iiyama
All computers
Fn + F3
IBM
All computers
Fn + F7
NEC
All computers
Fn + F3
Panasonic
All computers
Fn + F3
SHARP
All computers
Fn + F5
SONY
All computers
Fn + F7
SOTEC
All computers
Fn + F3
TOSHIBA
All computers
Fn + F5
Victor
All computers
Fn + F10
Note: Table information is current to December 2003.
Note:
* When the liquid crystal display of the notebook computer and the projector are displayed at the same time, the projected image might not
be correct even though the liquid crystal display shows a correct indication. Should this occur, stop the simultaneous display of the
notebook computer and try the mode with external output only. Try an operation such as that described in aforementioned Step 2 and try
closing the liquid crystal panel which might result in external output only.
* In some rare cases, the picture may not be displayed, depending on the connected device.
E-17
Connecting Personal Computers and Video Equipment
Connections with Composite Signals
Video Equipment with VIDEO Connectors
• The input setting of the VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project, please
change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input Format]
→ [Video].
See “Input Format” on Page E-53.
Video Equipment with S-VIDEO Connectors
• Make the connection to the S-VIDEO connector of the projector using the supplied S-video cable.
• The input setting of the S-VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project,
please change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input
format] → [S-Video].
See “Input Format” on Page E-53.
Video deck, DVD player, document
camera, etc.
VIDEO
S-VIDEO
Video cable (Supplied item)
S-Video cable (Suppled item)
Note:
The picture may be disturbed when the input format is switched or when the mode is set back to auto. This is not a malfunction. The picture
will return to normal when the input is switched, etc.
E-18
Connecting Personal Computers and Video Equipment
Connections with Component Signals
When the Video Equipment Has a YCbCr Connector or YPbPr Connector
• The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “Component” using the menu sequence of [Setup] → [Input Format] → [RGB].
See “Input Format” on Page E-53.
• When projecting the YCbCr signal or YPbPr signal, if the color of the overall image strongly leans toward being greenish or
another color, change the setting under the menu of [Color] → [Color Space].
See “Color Space” on Page E-47.
Note:
* When the input format has been switched, you may be required to reconnect the input signal.
* In some rare cases, the picture may not be displayed, depending on the connected device.
Component cable (Not supplied)
Green
Blue
Red
Y
Cb
Cr
COMPONENT
COMPONENT
Y
Pb
Pr
Green
Blue
Red
Component cable (Not supplied)
Projecting component signals
Please note that when inputting 480i or 576i signals using a separately sold component cable and viewing video images, depending on the
connected device and the video source being projected, the picture may be disturbed or may not be projected properly.
In such cases, it is possible to achieve a picture with no disturbance that is projected properly by either switching to 480p signals or
connecting using an S-Video cable instead.
E-19
Connecting Personal Computers and Video Equipment
Connections with the AUDIO Jack
* Make the connection to the projector’s AUDIO jack using the supplied audio cable. When the audio jack of the equipment that
is to be connected is of the RCA phono type, make connection via the supplied audio conversion cable.
* The built-in speaker of the projector provides monaural audio. To enjoy convincing audio reproduction, please connect the
audio output of the video equipment to your audio system.
* The built-in speaker outputs the audio of the equipment connected to the AUDIO jack.
White
Audio cable (Supplied item)
AUDIO OUT
L
Audio conversion cable
(Supplied item)
Audio cable (Supplied item)
E-20
R
Red
Power Cable Connections and Switching the Power On/Off
There is an order in which the power cable is connected and the power is switched on/off.
Operating
1 Connect the AC IN connector of the projector and the power outlet using the supplied power cable.
The STANDBY indicator will light in amber, and the unit will enter the standby mode.
STATUS
U
AT
ST
S
ND
STA
BY
AN
ST
DB
Y
AU
To wall outlet
TO
UR
CE
P
C
C
O
N
TR
O
L
SO
STANDBY
S
V
ID
E
O
V
ID
E
O
A
U
D
IO
M
O
U
S
E
Lit amber
R
G
B
Firmly plug in all the way.
2 Switch on the projector power
This indicator is also lit green in Low-mode.
Press the STANDBY button.
STANDBY
(button on main unit)
The first time the power is switched on after purchase, [Menu
Language Select] will be displayed. See Page E-22 for information about language selection.
• When the power is turned on, the STANDBY indicator starts
flashing green, then stops flashing after about 60 seconds. If
the STATUS indicator lights green at this time, the lamp mode
is set to “Low”. See E-52 for instructions on selecting.
• If the power does not come on, see “When the STATUS Indicator is Lit or Flashing” on Page E-58.
If the “Password” input window is displayed: See E-35.
A password is set for this projector.
The projector cannot be used unless the correct password is input.
To turn off the power: See E-23.
STATUS
STATUS
STATUS
STANDBY
STANDBY
STANDBY
Lit amber
Flashing green
(Approximately 60
seconds)
STANDBY
RGB
MENU
Lit green
Power is on
LASER
VIDEO
AUTO
QUICK
Q
The projector is now capable of regular projection.
3 Switch on the power of the connected equipment
Note:
• When the power plug will be unplugged from the power outlet, please place the projector near the power outlet so that it may be reached
easily.
• Press the STANDBY button after the STANDBY indicator is lit in amber.
E-21
Power Cable Connections and Switching the Power On/Off
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Language Select] will be displayed. Follow the procedure described below and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clockwise to focus it. See Page E-25.
Cursor
1 Press the SELECT 왖왔 buttons of the Remote control and align the deep blue cursor with [English].
STANDBY
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
TIMER
MUTE
1
2
VOL
ZOOM
3
4
2 Press the ENTER button to set.
This will set the language and [Menu Language Select] will close.
R-CLICK/
CANCEL
ENTER
FREEZE
TIMER
MUTE
1
2
VOL
ZOOM
3
4
This completes the selection of the display language.
Caution:
[Menu Language Select] will not appear the next time the power is switched on.
Should a change of language become necessary, see “Language” on Page E-54.
E-22
Power Cable Connections and Switching the Power On/Off
Finishing
1 Switch off the power of the connected equipment
2 Switch off the power of the projector
Press the STANDBY button.
STANDBY
RGB
LASER
VIDEO
MENU
AUTO
QUICK
Q
STANDBY
(button on main unit)
The [Power Off] display appears.
When the level gauge reaches maximum, the projection screen
will go off (in about 5 seconds) and the projector will enter the
power-off operation.
Note
* The operation can be cancelled by pressing a button other than
the STANDBY button.
* One more press of the STANDBY button will switch off the power.
Power Off
OK ?
The STANDBY indicator changes to flashing amber and lights a
steady amber after about 90 seconds (when the unit enters the
standby mode).
STATUS
STATUS
STATUS
STANDBY
STANDBY
STANDBY
Lit green
Flashing amber
(Approximately 90
seconds)
Lit amber
Standby mode
3 Unplug the power cable
Check that the STANDBY indicator is lit in amber and then
unplug the power cable.
The STANDBY indicator will go off when the power cable is unplugged.
Warrning
Do not unplug the power cable while the STANDBY indicator is flashing amber. Doing so may shorten the life of the lamp
or damage the projector.
E-23
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
Adjustment of the Projection Screen
1 Turn the zoom ring to adjust the screen size of the projection image.
Adjust the image to match the desired screen size. When outside of the adjustment range, move the projector to the rear or
forward.
Zoom ring
2 Adjust the projection image to the screen.
Check that the screen is set level and vertically.
(1) If the image is shifted to the left or right, move the main unit horizontally. (Align the center of the screen and the center of
the projector lens.)
(2) If the image is shifted vertically, move the image up or down with the adjuster. See “Making Adjustments with the Adjusters” on Page E-25.
(3) If the image is slanted, adjust by turning the right or left adjuster. See “Making Adjustments with the Adjusters” on Page E25.
(4) A projection image such as that illustrated in the diagram is the result of the projector not being perpendicular to the
screen. Set the projector so that it is pointing straight toward the screen.
(5) If the image shows keystone distortion, adjust using remote control or menu operations. See “Keystone” on Page E-50.
(2)
(1)
(3)
(4)
(3)
(5)
E-24
(4)
Adjustment of the Projection Screen
3 Turn the focus ring and adjust the focus of the screen
Focus ring
XD70
Making Adjustments with the Adjusters
TA
TU
S
S
TA
N
D
B
Y
S
TA
N
D
B
Y
A
U
TO
S
O
U
R
C
E
(1)
S
While viewing the projection image, (1) press and hold
the adjuster buttons located at the left and right and, (2)
raise the projector to align the image with the screen, then
release your fingers.
Turn the left and right adjusters for fine adjustment.
Adjust so that there is no shaking of the projector.
(1)
(2)
Adjuster button
Note:
When the projector has a suspended or rear installation is used, the orientation of the projection will need to be changed.
Please see “Vertical Flip” on Page E-50.
E-25
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see “Menu Operation Method” on Page E-37 and the various items on
Pages E-44 to E-57.
Input Selection
This operation selects the input signal to be projected.
STANDBY
Main unit operation: Press the SOURCE button.
AUTO
When Auto Source is On
Whenever the SOURCE button is pressed, the projector automatically selects
another source that has the next input signal.
SOURCE
When Auto Source is Off
The input selection condition used last time will be set.
Each press of the button moves the selection one step in the sequence of RGB →
VIDEO → S-VIDEO. Note that the various input signals will become the signal
type set with [Input Format] See“Input Format” on page E-53.
Remote control operation: Press the desired input selection button.
RGB button ........ Switches the RGB input.
VIDEO button ..... The input switches between VIDEO and S-VIDEO each time the button is
pressed.
STANDBY
When Auto Source is On
When an input signal is not present at the selected source, the projector automatically selects the next source that has an input signal.
When Auto Source is Off
The projector switches to the selected source regardless of whether an input signal is present.
Note:
* When you do not operate source selection, the projector will assume the input selection condition that was previously used.
* See “Auto Source” on Page E-51 for information about the Auto Source on and off
conditions.
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
TIMER
MUTE
1
2
VOL
ZOOM
3
4
Automatic Adjustment
This function automatically adjusts the position shift, screen size, vertical stripes,
and color infidelity of the projected analog RGB input signal.
Normally automatic adjustment is performed at the time of signal selection.
STANDBY
AUTO
Main unit operation/Remote control operation: Press the AUTO button.
A press of the AUTO button starts the automatic adjustment.
SOURCE
Note:
* If the display position is shifted, vertical lines appear on the picture, or the projection
is not good even after using automatic adjustment, please perform image adjustment
manually. See “Picture Adj. / Fine Picture / H Position / V Position” on Page E-44.
* When the image extends beyond the boundaries of the screen or is smaller than the
screen, set Aspect to “Auto”. See “Selection of Aspect Ratio” on Page E-27 and “Aspect” on Page E-49.
STANDBY
RGB
LASER
VIDEO
MENU
AUTO
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
E-26
MUTE
TIMER
General Operation
Selection of Aspect Ratio
This function selects horizontal and vertical picture proportions of the input signal.
The operations are the same. See E-49 [Aspect].
Personal Computer Signal
Auto ............ Automatically enlarges or reduces the image to project a full screen in a ratio of 4:3
Direct .......... Maintains the aspect ratio and projects a picture of the maximum displayable size
Real ............ Projects the input signal without pixel conversion
Input Signal
Auto
Direct
Real
The setting is higher
than the display resolution of the projector.
The setting is lower
than the display resolution of the projector.
Video Signals / Component Signals
Auto ............ While maintaining the aspect ratio, projects a full screen so that no portions extend beyond the boundaries of the screen. The top
and bottom of the 16:9 image becomes black.
Wide ........... Projects to fill the full width with the entire image at 16:9.
(This feature is used to project a squeezed image in a proper aspect ratio.)
Zoom .......... Projects only the 4:3 portion within 16:9 image to fill the screen.
(Portion that extend off screen is cut.)
Aspect ratio selection
Auto
Wide
Zoom
4:3 screen
16:9 screen
Note:
When selection has been made for the “Real” setting of the personal computer signal (i.e., when the input signal and the projector display
resolution are high) and the “Zoom” setting of the video signal, pressing the SELECT 왖왔왗왘 buttons on the remote control will permit
movement of the display position.
E-27
General Operation
Freezing a Moving Picture
This function is used to stop and view a moving picture. Note that the input
image continues to advance even though the picture there is a still picture
condition.
STANDBY
A press of the FREEZE button changes the screen to a still picture. A
further press returns the screen to a moving picture.
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
TIMER
MUTE
1
2
VOL
ZOOM
3
4
Cancelling Video and Audio Temporarily
This function is used to cancel the video and audio at the same time.
STANDBY
A press of the MUTE button will blank the picture and the sound, and
the screen will take on the background color that has been set.
Another press will cause a return to the original conditions.
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
TIMER
MUTE
1
2
VOL
ZOOM
3
4
Adjustment of the Volume
This function adjusts the volume of the built-in speaker.
STANDBY
(1) Press the 왖 or 왔 VOL button to adjust the volume.
The volume adjustment display appears when one of the buttons is
pressed.
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
R-CLICK/
CANCEL
ENTER
The 왖 button increases the volume and the 왔 button decreases the
volume.
(2) Press the CANCEL button to immediately close the display.
The display will close when there has not been an operation in about
10 seconds.
Note:
* Adjustment of the volume will not produce any sound unless an image is
being projected.
* Please make connections to the AUDIO connectors of the projector with the
supplied audio cable.
E-28
(2)
FREEZE
TIMER
MUTE
1
2
VOL
ZOOM
3
4
(1)
General Operation
Enlargement of the Image and Video Movement
This function digitally enlarges the personal computer image and video
image.
(1) Press the ZOOM button to enlarge the image.
The zoom display appears when the ZOOM button is pressed.
STANDBY
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
(2)
R-CLICK/
CANCEL
ENTER
Each press of the 왖 button enlarges the image and each press of the
왔 button makes the image smaller (returning it to 1:1).
Zoom
0
(No enlargement)
Zoom
FREEZE
(3)
TIMER
MUTE
1
2
VOL
ZOOM
3
4
(1)
21
(Approximately 2 times enlargement)
Note:
The degree of enlargement will differ depending on the signal.
(2) Pressing the SELECT 왖왔왗왘 buttons on the remote control at
the time of the zoom operation will cause the display position to
move.
(There will not be any movement when zoom is at 0.)
Zoom
21
(Approximately 2 times enlargement)
Zoom
21
(Movement)
(3) Press the CANCEL button to immediately close the display.
The display will close when there has not been an operation in about
10 seconds.
Note:
After magnifying the image, be sure to use the ZOOM button to bring the gauge
value back to “0”.
The image can also be moved in the following circumstances.
•
•
When “Aspect” is set to “Real” by the signal of the personal computer, and the input resolution is higher than the display
resolution of the projector.
When “Aspect” is set to “Zoom” by the video signal.
Note:
* Zoom and image movement functions are cancelled when the input is switched.
* The greater the zoom enlargement, the less distinct the image will appear. The reason for this is that the dots are being digitally corrected
so that they are not conspicuous.
* Movement of the screen will not be possible when the menu screen is being displayed.
E-29
General Operation
Using the Presentation Timer
The presentation is given while checking the timer displayed
on the screen.
The gauge display allows the remaining time to be known at
a glance.
(1) Press the TIMER button to show the settings display.
The display will close when an operation has not been made
for about 10 seconds.
STANDBY
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
(2)
R-CLICK/
CANCEL
ENTER
CANCEL button
(3)
FREEZE
TIMER
MUTE
(1)
[Timer settings display]
1
2
VOL
ZOOM
3
4
Press the CANCEL button to close the display immediately.
(2) Use the 왗 and 왘 SELECT buttons to set the time.
The setting contents are “Off” and from 10 to 60 minutes (in
10-minute intervals)
Settings can also be made with the SELECT 왗왘 buttons.
(3) Press the ENTER button and start the timer.
• The display of the timer setting will close, the display of the
timer will appear and simultaneously the timer will start.
Gauge (Blue)
[Timer Display]
The blue gauge indicates the remaining time. When the
gauge disappears,the time is up.
The gauge continues to be displayed when the timer is
stopped.
When the remaining time is
“0” (Gray)
• Press the ENTER button to restart the timer. The timer will
start with the same time setting.
• Press the CANCEL button to close the timer display. The
timer setting will return to “Off”.
Moving the Position of the Timer Display
The SELECT 왖왔왗왘 buttons on the remote control permit movement within the movable range of the timer display.
Movable Range of the Timer Display
Note:
* The timer display will be closed while the menu or the quick menu is displayed, and while a message is displayed; however, the timer will
still be operating at such times. Also, the timer will not be displayed unless a signal is being input.
* While the presentation timer is being displayed, screen movement will not be possible in the zoom mode.
E-30
General Operation
Using the Laser Pointer
The remote control unit’s laser pointer can be used to point to the section currently being explained, making presentations more effective.
CAUTION
Do not look at the laser pointer’s light source.
Be sure to heed the following. Pointing the laser beam at
the eyes could lead to reduced vision or vision impairment.
• Never look at the laser pointer’s light source.
• Do not point the laser beam at people.
• Do not let children use the laser pointer.
This label is located on the side of the remote control.
Operation
The red laser beam is emitted from the tip of the remote control
unit while the LASER button is pressed in. Point the remote control unit’s transmitter in the direction you want to indicate.
The laser beam turns off when you release your finger from the
LASER button.
S
TA
N
D
B
Y
R
G
B
LA
E
O
S
U
E
N
ID
E
V
M
R
A
U
TO
Q
U
K
N
Q
IC
E
TE
R
FR
EE
ZE
/
K
L
LIC E
-C C
R AN
C
M
U
TE
TIM
1
E
R
V
O
L
2
3
ZO
O
M
4
LASER
Note:
If a button on the remote control unit is held in continuously for approximately 30 seconds, signal transfer will be suspended. To resume
transferring signals, press the button again.
Also, to use the jog button after signal transfer has been suspended, first press any other button, then press the jog button.
E-31
General Operation
Performing Mouse Operations on the Computer
with the Remote Control Unit
When a computer and the projector are connected, mouse operations can be performed on the computer using the
projector’s remote control unit. When projecting images from the computer, the projector can be operated and mouse
operations on the computer performed with the same remote control unit, making for efficient presentations.
Connecting the computer and projector
Use the USB cable included with the projector to connect the computer’s USB (type A) connector to the projector’s MOUSE
connector.
Note:
* Be sure to plug the cable in securely.
* Depending on the type of connection, the computer’s operating system, etc., it may be necessary to change settings or restart the computer after making the connections.
USB connector
USB cable (mini B to A type) (Supplied item)
Functions of the mouse function buttons
When operating, point the remote control unit’s transmitter towards the remote control sensor on the projector.
L-CLICK button (on back)
Press this to perform the left-click operation.
STANDBY
LASER
VIDEO
RGB
AUTO
MENU
QUICK
JOG buttons
These move the computer’s pointer in the corresponding direction.
Q
R-CLICK button
Press this to perform the right-click operation.
R-CLICK/
CANCEL
ENTER
FREEZE
TIMER
MUTE
1
2
VOL
ZOOM
3
4
INFORMATION
The R-CLICK/CANCEL button is used for both the projector and mouse function. When the R-CLICK/CANCEL button is pressed while a menu is open, the
menu is closed.
Note:
Connections with USB Cables
* For PC/AT compatible computers, this function cannot be used with operating systems other than Windows 98SE, Me, 2000 and XP. For
Macintosh computers, this function cannot be used with operating systems other than OS 9 and later.
* When the cable is disconnected and then reconnected to the USB port of the personal computer or the MOUSE connector of the projector,
allow at least 5 seconds before reconnecting. Do not repeatedly disconnect and reconnect the cable in a momentary fashion. The personal
computer may not be able to correctly identify the projector as a result.
* The supplied USB cable is a dedicated cable for this projector. There is no guaranty that it will work in connections with other USB
equipment.
* This function may not work with some computers.
E-32
General Operation
Controlling the Projector from a Computer
Use the control connector if the projector cannot be operated with the remote control unit, for example when it is
suspended from the ceiling.
Connecting the computer and projector
Use a commercially available serial cable (D-Sub 9-pin, straight) to connect the computer’s RS-232C connector to the projector’s
control connector (PC CONTROL).
RS-232C
connector
Serial cable (D-Sub 9-pin, straight) (commercially available)
Note:
* This function may not work with some computers.
* Specialized knowledge is required to use the control connector. Consult a specialist, such as the person suspending the projector from the
ceiling.
E-33
General Operation
Protecting the Projector with the Security Lock
A password can be registered and the security lock set in order to protect the projector from unauthorized use.
Registering the password
The password is registered using the menus. For instructions on operating the menus, see “Menu Operations” on E-37.
(1) Select “Security Lock” in the “Option” menu and set it to “Enable”.
The menu closes and the password registration display appears.
(2) Use the number buttons (1 to 4) to register the password.
Be sure to input a 4-digit number.
Example: Registering the password “2441”
(1) Press number button “2”. An “ ” (asterisk) appears at the first place.
Next press number buttons “4”, “4” and “1” in that order. Asterisks appear
in all four places.
*
STANDBY
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
(2) Input the password again. An “ ” appears when the input number
matches. If there is a mistake, the asterisks turn off. Start over from step
(1) above.
If the password matches, the password registration display closes.
*
Note:
To cancel the number you have input, press the CANCEL button.
The asterisks disappear and the display returns to the input standby mode at the first
place.
To cancel the password registration mode, press the CANCEL button again. The “Password” display turns off.
This completes password registration.
The “Password” input display appears the next time the power is turned
on.
Note:
Canceling the password (restoring the default)
In the standby mode, cancel the security lock mode using the procedure
described below.
1. Press the AUTO button for 5 seconds to set the security lock clear mode.
(Check that the STATUS indicator has lit green.)
2. Press the AUTO and SOURCE buttons simultaneously for 5 seconds.
(Check that the STATUS indicator is flashing green.)
STATUS
STANDBY
STANDBY
AUTO
SOURCE
Note:
The numbers you have input are not displayed. Be sure to write down the password
and store it in a safe place.
E-34
TIMER
MUTE
1
2
VOL
ZOOM
3
4
General Operation
If the password input display appears when the power is turned on
When a password has been registered, the “Password” input window appears on the projected image when the power is turned
on. The projector continues projecting this image until the correct password is input. At this time, only the STANDBY button (power
off) works. Use the procedure described below to input the registered password. For instructions on registering the password, see
E-34.
Input the password using the number buttons (1 to 4).
Be sure to input the registered 4-digit number.
Example: To input the password “2441”
Press number button “2”. An “ ” (asterisk) appears at the first place.
*
Next press number buttons “4”, “4” and “1” in that order. Asterisks appear in all
four places.
If the password matches, the window turns off and the projector can be used
normally.
[Password input window]
Canceling the password/Changing the password
The password is canceled and changed using the menus. For instructions on operating the menus, see “Menu Operations” on E37.
Canceling the password
Select “Security Lock” in the “Option” menu and set it to “Disable”.
This clears the password and disables the security lock.
The password input display no longer appears when the power is turned on.
Changing the password
After setting “Security Lock” to “Disable” as described above, set it back to “Enable”. The menu closes and the password registration display appears.
Register the new password. See “Registering the password” on E-34.
E-35
General Operation
Using the Quick Menu
This function permits frequently used adjustments to be
performed quickly.
Note that the Quick Menu will not be displayed unless the signal
of the connected equipment is input. Please select the input that
you wish to adjust.
STANDBY
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
(1) A press of the QUICK MENU button brings up the quick
adjustment display.
Further presses cause the adjustment display to change in
sequence.
The adjustment display can be selected with use of either the
SELECT 왖 or 왔 button.
(2) Press the cursor 왗 or 왘 button to make the adjustment.
(3) To close the display immediately, press the CANCEL button.
In the absence of operations for a period of about 10 seconds, the display will close automatically.
(2)
R-CLICK/
CANCEL
ENTER
(3)
FREEZE
TIMER
MUTE
1
2
VOL
ZOOM
3
4
Content of Adjustments and Settings
Example: Brightness adjustment display
Display Item
Adjustment/Setting
Brightness
Adjusts the brightness of the image. See page E-44.
Contrast
Adjusts the contrast of the image. See page E-44.
Keystone
Corrects (vertical) keystone distortion of the screen. See page E-50.
Volume
This function adjusts the volume of the built-in speaker. See page E-28.
Presentation timer
Sets the time of the presentation timer. See page E-30.
Quick Color Adj.
Select the preset color mode. See page E-46.
E-36
(1)
Menu Operation Method
• This section describes only the menu operation method. Please see this item should you need information while
performing menu operations.
• For information about a menu function, adjustment, or setting, please see one of the pages containing such descriptions.
• Adjustments and settings are made by projecting an image and adjusting to an optimum condition.
• The remote control should be pointed toward the remote control sensor of the projector and operated.
• To return the various items that have been changed via the menu to their standard values (i.e., default values at time
of shipping from the factory), see “Factory Default” on Page E-56. (Some items will not return to their initial values.)
• The adjustment/setting items and contents will differ depending on the input selection and the adjustment/setting
items that can be used with the input signal are displayed on the menu.
Names and functions of remote control unit buttons used for menu operations
STANDBY
LASER
VIDEO
RGB
MENU button
Used for menu display and menu closure.
AUTO
QUICK
MENU
Q
SELECT 왖왔왗왘 buttons
Used in the selection of menu names and item names as
well as in setting and adjusting the item contents.
R-CLICK/
CANCEL
ENTER
FREEZE
TIMER
MUTE
1
2
VOL
ZOOM
3
4
CANCEL button
Used to return to menu name selection as well as to close
the menu (and the sub menu display).
ENTER button
Used to set the verification display.
E-37
Menu Operation Method
Menu Screen Names and Functions
Menu Name
This is the title of the menu.
There is a change to the title screen
when the menu is selected.
The cursor moves to the selected menu
name.
Cursor (Deep Blue)
This permits setting/adjustment of the
item located at the cursor position.
Item Name
This is the name of the adjustment or setting.
Icon: Pressing the ENTER button displays the sub menu or setting contents.
Adjustment Bar and Settings Contents
Adjustment Bar: The increases and decreases in bar length express the adjustment condition.
Setting Contents: Displays the contents that have been set.
Sub menu
Adjustment Bar
Item Name
E-38
Settings Contents
Menu Operation Method
Performing Menu Operations
• Only “Setup”, “Options” and “Info.” can be selected when no signal is being input.
• The menu display will close if, after pressing a button, the next button operation is not made within 30 seconds.
• The adjustment and the setting values are stored even when the power is switched off or the plug is disconnected
from the power outlet.
(Note that some items are not stored.)
Preparation
Switch on the power of the connected equipment, start the play operation or another operation, and input
the signal to the projector.
Select the input that you wish to adjust.
The menu display of the description diagram depicts an example in which the “Keystone” item name is selected.
Menu Display
1
Press the MENU button to display the menu
STANDBY
RGB
LASER
VIDEO
AUTO
QUICK
MENU
Q
R-CLICK/
CANCEL
ENTER
FREEZE
MUTE
TIMER
The menu name that existed when the menu was closed previously will be displayed.
Selection of the Menu Name
2
Press the SELECT 왗왘 button to select the menu name
STANDBY
RGB
LASER
VIDEO
MENU
AUTO
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
MUTE
TIMER
Each press of the SELECT 왘 button advances the selection one step in the sequence of “Color” → “View” → “Setup” →
“Option” → “Info.” → “Image”. Each press of the SELECT 왗 button causes a return of one step.
The cursor moves to the selected menu name.
Note:
Please check that the cursor of the item name has disappeared at the time of menu name selection.
Press the CANCEL button to make the cursor disappear.
E-39
Menu Operation Method
Displaying the Cursor
3
Press the 왔 SELECT button to display the item name selection cursor.
STANDBY
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
This condition allows selection of the
item name.
TIMER
MUTE
Selection of the Item Name
4
Press the SELECT 왖왔 button to align the cursor with the item name
STANDBY
LASER
VIDEO
RGB
AUTO
MENU
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
TIMER
MUTE
Items for which the
Icon Is Displayed
Press the ENTER button to display the submenu.
Press the SELECT 왖왔 button and align the cursor with the desired item name.
There are also some items for which the setting display or the verification display will appear. Please see the various item
descriptions.
R-CLICK/
CANCEL
ENTER
FREEZE
Sub menu
TIMER
MUTE
1
2
VOL
ZOOM
3
4
Making Adjustments/Settings
5
Press the SELECT 왗왘 button and make the adjustment (or setting) while viewing the image
When a button is pressed, the image will also change.
STANDBY
RGB
LASER
VIDEO
MENU
AUTO
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
MUTE
TIMER
Adjustment display: Each press of the button results in a change of 1 point and continued presses cause changes to
proceed in order.
Setting display: The setting contents display changes with each press of the button.
E-40
Menu Operation Method
Closing the Menu
6
Press the MENU button and close the menu display
STANDBY
RGB
LASER
VIDEO
AUTO
QUICK
MENU
Q
R-CLICK/
CANCEL
ENTER
FREEZE
MUTE
TIMER
Selecting Another Menu Name with Remote Control Operation
When a sub menu is displayed, press the CANCEL button and close the sub menu.
Press the CANCEL button again to turn off the item name
cursor.
STANDBY
RGB
LASER
VIDEO
MENU
AUTO
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
MUTE
TIMER
Press the SELECT 왗왘 button and select the menu name.
(Menu names cannot be selected when the item name
cursor is displayed.)
STANDBY
RGB
LASER
VIDEO
MENU
AUTO
QUICK
Q
R-CLICK/
CANCEL
ENTER
FREEZE
MUTE
TIMER
Note:
A press of the QUICK button while the menu is displayed will close the menu and display the quick menu. A press of the MENU button while
the quick menu is displayed will close the quick menu and display the menu.
E-41
Menu Operation Method
List of Item Names Offering Input Selection and Adjustments/Settings
The item names that can be adjusted/set will differ depending on the input signal.
u
om t Si
gn
R pon al
G
B en
t
VI
D
E
S- O
VI
D
EO
[Example of Menu Display Items at the Time of Input Signal RGB Selection]
p
Sub Menu
Item Name
Item Name
Image
Brightness
嘷
嘷
嘷
嘷
E-44
Contrast
嘷
嘷
嘷
嘷
E-44
嘷
嘷
E-44
嘷
嘷
E-44
嘷
嘷
E-44
In
Menu name
C
Reference
Page
Color
嘷
Tint
Sharpness
Picture Adj.
嘷
E-44
Fine Picture
嘷
E-45
H Position
嘷
E-45
V Position
嘷
嘷
Reset
Color
E-45
嘷
嘷
嘷
Quick Color Adj.
E-45
E-46
Gamma
嘷
嘷
嘷
嘷
E-46
Color Temp.
嘷
嘷
嘷
嘷
E-47
White
嘷
嘷
嘷
嘷
E-47
Color Space
嘷
E-47
嘷
White Balance
View
嘷
E-48
Aspect
嘷
嘷
嘷
嘷
E-49
Filter
嘷
嘷
嘷
嘷
E-49
Vertical Flip
嘷
嘷
嘷
嘷
E-50
Horizontal Flip
嘷
嘷
嘷
嘷
E-50
Keystone
嘷
嘷
嘷
嘷
E-50
Keystone Save
嘷
嘷
嘷
嘷
E-50
E-42
u
om t Si
gn
R pon al
G
B en
t
VI
D
EO
SVI
D
EO
Menu Operation Method
p
Sub Menu
Item Name
Item Name
Setup
Auto Source
嘷
嘷
嘷
嘷
E-51
Auto Power Off
嘷
嘷
嘷
嘷
E-51
Memu Position
嘷
嘷
嘷
嘷
E-52
Lamp Mode
嘷
嘷
嘷
嘷
E-52
RGB
嘷
嘷
嘷
嘷
E-53
Video
嘷
嘷
嘷
嘷
E-53
S-Video
嘷
嘷
嘷
嘷
E-53
Presentation Timer
嘷
嘷
嘷
嘷
E-53
Language
嘷
嘷
嘷
嘷
E-54
On Screen
嘷
嘷
嘷
嘷
E-54
Background
嘷
嘷
嘷
嘷
E-54
Startup Screen
嘷
嘷
嘷
嘷
E-55
Security Lock
嘷
嘷
嘷
嘷
E-55
Status
嘷
嘷
嘷
嘷
E-56
Factory Default
嘷
嘷
嘷
嘷
E-56
Lamp Timer Reset
嘷
嘷
嘷
嘷
E-56
Resolution
嘷
嘷
嘷
嘷
E-57
Frequency
嘷
嘷
嘷
嘷
E-57
Lamp Timer
嘷
嘷
嘷
嘷
E-57
Input Format
Option
Info.
In
Menu name
C
Reference
Page
E-43
Image
• Perform this operation while projecting the picture for which the adjustment/setting will be made.
• Select the menu name “Image”.
See “Menu Operation Method” on Page E-37 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-42.
Brightness / Contrast / Color / Tint / Sharpness
Picture qualities such as brightness and contrast will change depending on the whether the room is bright or dark. Please adjust to suit your
preference.
Select the desired item name and then adjust with the SELECT 왗왘 buttons.
Item Name
Brightness
Contrast
Color
Tint
Sharpness
SELECT 䊴 Button
Darker
Less contrast
Less dense color
More red
Softer image
SELECT 䊳 Button
Brighter
More contrast
Denser color
More green
Sharper image
Note:
* The adjustment values of the adjustable items are stored according to input source.
* “Tint” can only be adjusted when inputting NTSC composite/S-Video signals or
component signals.
Picture Adj. / Fine Picture / H Position / V Position
Usually, automatic adjustment is performed at the time of signal selection, but when automatic adjustment is not effective, these adjustments
can be performed.
Note:
When the image extends beyond the boundaries of the screen or is smaller than the
screen, check that the “View” → “Aspect” setting is set to “Auto”. See “Aspect” on
Page E-49.
Picture Adj. (Picture Adjustment)
Adjust this when bright and dark vertical bands appear on the screen.
Select the “Picture Adj.” item name and adjust with the SELECT 왗왘 buttons
so that the vertical bands disappear and brightness becomes uniform across
the screen.
E-44
Image
Fine Picture
Adjust this when the picture shows a lack of color fidelity or flickering.
Select the “Fine Picture” item name and adjust with the SELECT 왗왘 buttons
so that the lack of color fidelity or the flickering disappears.
H Position
Adjust this when the picture is shifted to the left or right.
Select the “H Position” item name and adjust with the SELECT 왗왘 buttons.
V Position
Adjust this when the picture is shifted up or down.
Select the “V Position” item name and adjust with the SELECT 왗왘 buttons.
Reset
This function resets (i.e., returns to the standard settings) the adjustment/setting value of the “Image” menu name.
A press of the ENTER button forces the reset.
Note:
* The item name “Fine Picture” at the time of RGB input will not be reset.
* “Reset” of the menu name “Image” can be reset for each input source.
* To reset the adjustments/settings of all the menu items (while noting that there are some items that cannot be reset), see “Factory Default”
on Page E-56.
E-45
Color
• Do the following operation while displaying the image you want to adjust or set.
• Select the menu name “Color”.
See “Menu Operation Method” on Page E-37 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Pages E42.
Quick Color Adj.
Select the preset color mode.
Select the “Quick Color Adj.” item name and select the setting contents with
the SELECT 왗왘 buttons.
Color ........... Select this to prioritize color.
Standard ..... Select this to prioritize brightness.
* When “Color” or “Standard” is selected, the “Gamma”, “Color Temp.” and “White” adjustment
items are displayed in gray and cannot be selected or adjusted.
Custom ....... “Gamma”, “Color Temp.” and “White” adjustment items can be selected
and adjusted
* The selected values for the different adjustment items are stored in the memory so the desired
color adjustments can be set.
Gamma
Gamma corrects the proportion of change of the dark portions from the
bright portions of the input signal.
Set this to reproduce natural color tone or to distinctly project a personal computer picture in a bright conference room.
Select the “Gamma” item name and select the setting contents with the SELECT 왗왘 buttons.
Normal ....... Correction with standard settings
Natural ........ Corrects for natural color tones
Real ............ Corrects with emphasis on brightness
Note:
When “Color” or “Standard” is selected for “Quick Color Adj.”, the “Gamma” adjustment item is displayed in gray and cannot be selected or adjusted.
E-46
Color
Color Temp.
The screen color is affected by the color of the illumination and other
extraneous light.
This function adjusts the white, which is the reference color for video
equipment, and improves the quality of color reproduction. Adjustment
can also be used to enhance skin colors.
Select the item name “Color Temp.” and select the setting contents with the
SELECT 왗왘 buttons.
Low ............
Medium ......
Normal .......
High ............
Produces warm whites (reddish)
Produces warm whites (yellowish)
Produces the white of sunlight
Produces cool whites (bluish)
Note:
When “Color” or “Standard” is selected for “Quick Color Adj.”, the “Color Temp.”
adjustment item is displayed in gray and cannot be selected or adjusted. See “Quick
Color Adj.” on E-46.
White
When projecting, this function is used to emphasize the whites of text or
diagrams on the personal computer.
Select the item name “White” and use the SELECT 왗왘 buttons to select the
setting contents.
Select the desired degree of white from among “Low”, “Medium”, and “High”.
Note:
When “Color” or “Standard” is selected for “Quick Color Adj.”, the “White” adjustment item is displayed in gray and cannot be selected or adjusted. See “Quick Color
Adj.” on E-46.
Color Space
Set this function when a component signal (YPbPr) is projected and the
image is extremely red or extremely green.
Select the item name “Color Space” and use the SELECT 왗왘 buttons to
select a color space setting that provides a normal image.
Selection contents at the time of YPbPr input
BT.709, SMPTE240
Note:
* When the component signal undergoes conversion processing to red, green,
and blue which express the image of the projector, the correct color cannot be
reproduced unless a system compliant with the color difference conversion system of the input signal is used. Color Space serves to make this selection.
* The color space can only be adjusted with high definition TVs.
E-47
Color
White Balance
This function automatically adjusts the black level and the white level of
the analog RGB input signal to suit the personal computer.
1
Select the item name [White Balance] and press the ENTER button.
The display will change to [Input Black Signal].
2
The screen background color of the connected personal computer
will be set to black.
3. Press the ENTER button. The display will change to [Adjusting Black]
and the black level will be adjusted.
4
The adjustment of the black level is completed and the display
changes to [Input White Signal].
5
The screen background color of the connected personal computer
will be set to white.
6
Press the ENTER button. The display will change to [Adjusting White]
and the white level will be adjusted.
[White balance complete] is displayed for a while and the adjustment is
completed.
E-48
View
• Perform this operation while projecting the picture for which the adjustment/setting will be made.
• Select the menu name “View”.
See “Menu Operation Method” on Page E-37 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-42.
Aspect
This function sets the horizontal and vertical picture proportions of the
input signal.
Select the item name “Aspect” and select the setting contents with the SELECT 왗왘 buttons.
Personal Computer Signal
Auto ............ Automatically enlarges or reduces the image to project a full screen in a
ratio of 4:3
Direct .......... Maintains the aspect ratio and projects a picture of the maximum
displayable size
Real ............ Projects the input signal without pixel conversion
Video Signals / Component Signals
Auto ............ While maintaining the aspect ratio, projects a full screen so that no portions extend beyond the boundaries of the screen. The top and bottom of
the 16:9 image becomes black.
Wide ........... Projects to fill the full width with the entire image at 16:9.
(This feature is used to project a squeezed image in a proper aspect ratio.)
Zoom .......... Projects only the 4:3 portion within 16:9 image to fill the screen.
(Portion that extend off screen is cut.)
See “Selection of Aspect Ratio” on Page E-27 for diagrams of projection screen
images that correspond to the input signals.
Note:
Please note that using this monitor for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and projecting
a 4:3 screen in wide mode or leaving a squeezed screen as a compressed image
raises concern about the infringement of the copyright holder’s rights which are
protected by copyright law.
Filter
This function sets the sharpness when the input signal is adjusted to
the resolution of the projector and enlarged or reduced.
Select the item name “Filter” and select the setting contents with the SELECT
왗왘 buttons.
Smaller numerical values result in a sharper picture and larger values result in
a softer picture. Please select your desired setting value.
E-49
View
Vertical Flip/Horizontal Flip
In selecting the method of projecting to the screen, these functions are
set when the projector is in a suspended or a rear screen installation.
XD70
XD70
Select the item name “Vertical Flip” or “Horizontal Flip” and select the setting
contents with the SELECT 왗왘 buttons.
XD70
07D X
XD70
“Vertical Flip” On
“Horizontal Flip” On
XD70
07D X
XD70
XD70
“Vertical Flip” Off
“Horizontal Flip” On
XD70
Keystone
07D X
07D X
Keystone distortion will occur when the projector and screen are on an
angle (in the vertical orientation). This function is used to correct this
distortion.
XD70
XD70
Select the item name “Keystone” and correct the keystone distortion using the
SELECT 왗 왘 buttons.
Press the “왗” button.
Press the “왘” button.
Note:
* The menus and other on-screen displays cannot be adjusted.
* Please note that depending on the projected picture and the projection conditions, it may not be possible to eliminate keystone distortion completely.
Keystone Save
This function is used to save the keystone adjustment values.
Setting Keystone Save to on will set the previous keystone adjustment values
when projecting after the power cable has been disconnected and then reconnected.
Select the item name “Keystone Save” and set with the SELECT 왗왘 buttons.
Off .............. The keystone adjustment values return to the initial values when the power
cable is unplugged.
On ............... The keystone adjustment values are retained in storage even when the
power cable has been unplugged.
Note:
Regardless of whether Keystone Save is set to “On” or “Off”, when projection is
from the standby condition, the picture is projected using the previous keystone
adjustment values.
E-50
XD70
“Vertical Flip” Off
“Horizontal Flip” Off
“Vertical Flip” On
“Horizontal Flip” Off
XD70
Setup
• Select menu name “Setup”.
See “Menu Operation Method” on Page E-37 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-42.
Auto Source
The Auto Source function automatically detects the input signal when
the power supply is switched on and when the input is switched.
Select the item name “Auto Source” and select the setting contents with the
SELECT 왗왘 buttons.
On ............... Switches on the automatic detection function
Off .............. Switches off the automatic detection function
Signal Detection Order When On
The sequence of RGB → VIDEO → S-VIDEO is searched repeatedly.
When a signal is detected, the search is stopped and the image is projected.
Auto Power Off
This function switches off the projector power automatically when the
input of the projector enters a no-signal condition.
Select item name “Auto Power Off” and select the setting contents with the
SELECT 왗왘 buttons.
On ............... The power is switched off when there is no signal.
Off .............. The power is not switch off even when there is no signal.
Operation when Function is On
• The “No Signal Power Off” display appears when a no-signal condition continues for approximately 10 seconds. The power is switched off about 5
minutes after this.
• If a signal is input during the appearance of the display and an operation
button other than the STANDBY button is pressed, the display is closed and
the function is cancelled.
Note:
Some video decks and other equipment output a blue background or other video when playback ends. When this happens, a signal is being
input to the projector and Auto Power Off is not activated.
E-51
Setup
Menu Position
This function sets the display position of the menu.
Select item name “Menu Position” and select the setting contents with the
SELECT 왗왘 buttons.
............. Displays on the left side
............. Displays on the right side
Lamp Mode
Use this if the picture is projected on a small screen and the picture is
too bright or when projecting images in dark rooms.
Select the item name “Lamp Mode” and select the setting contents with the
SELECT 왗왘 buttons.
Low ............ The lamp brightness is set to 80% and the lamp life is extended.
(STATUS indicator is green)
Normal ....... The lamp brightness is set to 100% and the screen is bright.
(STATUS indicator is off)
Note:
Frequent switching this mode can degrade the lamp.
STATUS Indicator
STATUS
STANDBY
E-52
Setup
Input Format
This function is used in setting the input signals of the input connectors.
Normally, this should be set to Auto. When identification is not possible
with Auto, make the setting.
Select the item name “Input Format”, press the ENTER button, and the sub
menu will open.
Select the connector that is to be changed, and select the setting contents
with the SELECT 왗왘 buttons.
[RGB]
This is the signal setting for the RGB connector.
Auto ............ Automatically identifies the signal.
RGB ............ Analog RGB signal is set.
Component . Component signal is set.
[Video] and [S-Video]
[Video] is the color system setting for the VIDEO connector and [S-Video] is
the color system setting for the S-VIDEO connector.
Auto ............ Automatic identification.
NTSC .......... Fixed to the NTSC system.
NTSC 4.43 .. Fixed to the NTSC 4.43 system.
PAL ............. Fixed to the PAL system.
PAL M ......... Fixed to the PAL M system.
PAL N ......... Fixed to the PAL N system.
PAL 60 ........ Fixed to the PAL 60 system.
SECAM ....... Fixed to the SECAM system.
Presentation Timer
The presentation is given while checking the timer displayed on the
screen.
The gauge display allows the remaining time to be known at a glance.
Select the item name “Presentation Timer” and select the setting contents
with the SELECT 왗왘 buttons.
Setting contents: Off, 10 min., 20 min., 30 min., 40 min., 50 min., 60 min.
To start the timer...
Press the MENU button and open the menu.
The timer display will appear at the lower right and the timer will start.
See “Using the Presentation Timer” on Page E-30 for details.
E-53
Option
• Select menu name “Option”.
See “Menu Operation Method” on Page E-37 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-42.
Language
This function sets the language that is displayed on screen in
the messages and menu displays.
Select item name “Language” and press the ENTER button to open
the Language sub menu.
Select the language with the SELECT 왖왔 buttons.
On Screen
This function switches on/off the messages displayed with a black
frame such as the input signal information and the aspect ratio.
Select item name “On Screen” and select the setting contents with the
SELECT 왗왘 buttons.
On ............... The message is displayed.
Off .............. The message is not displayed.
Note:
Even when set to off, messages that are not in a black frame will be displayed.
Example of a display when the
FREEZE button is pressed
Freeze
Background
This function sets the screen color when the input source is nosignal.
Select item name “Background” and select the setting contents with
the SELECT 왗왘 buttons.
Blue ............ Sets a blue screen when there is no signal
Black ........... Sets a black screen when there is no signal
E-54
Option
Startup Screen
This is the selection of whether or not to display the logo screen
at startup time.
Select item name “Startup Screen” and select the setting contents
with the SELECT 왗왘 buttons.
Logo ........... Displays the logo.
Blank .......... Does not display the logo.
Note:
When “Logo” is selected at the startup screen, the “PROJECTOR XD70”
logo is displayed.
Security Lock
A password can be registered and the security lock set in order
to prevent unauthorized use of the projector.
For instructions on using the security function, see “Protecting the
Projector with the Security Lock” on E-34.
Select item name “Security Lock” and select the setting contents with
the SELECT 왗왘 buttons.
Disable ....... The security lock is disabled.
The projector can be operated without inputting the password.
Enable ......... The security lock is enabled.
The security lock is activated when the power is turned on, and
the password must be input in order to operate the projector.
E-55
Info.
• Select menu name “Info.”.
See “Menu Operation Method” on Page E-37 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-42.
Status
This displays information about the equipment.
Select item name “Status” and press the ENTER button.
There is a change to the status display.
Press the CANCEL button to return to the menu.
Display Contents:
Projector model and firmware version.
Factory Default
This function returns the adjustments and settings of all the input sources to the standard factory default values.
Select item name “Factory Default” and press the ENTER button.
There is a change to the display [Press “ENTER” to Factory Default
Set].
Press the ENTER button to initialize.
To cancel, press the CANCEL button and there will be a return to the
menu.
Items that are not set to the factory default:
Projection method, Language and Lamp Timer and Security.
Lamp Timer Reset
This function resets the lamp timer. Be sure to perform the reset
operation when the lamp cartridge has been replaced.
Select item name “Lamp Timer Reset” and press the ENTER button.
There is a change to the display “Press “ENTER” to Lamp Timer Reset”.
Press the ENTER button to initialize.
To cancel, press the CANCEL button and there will be a return to the
menu.
E-56
Info.
Resolution / Frequency
This function displays the resolution and frequency of the detected input signal.
Lamp Timer
This displays the lamp timer.
This projector has an Low mode function. The lamp life will differ between
Normal mode and Low mode.
Lamp Life
Use only in Normal mode: approx.2000 hours
Use only in Low mode: approx.3000 hours
* Lamp life will differ when there has been switching between the modes.
• When Lamp Life Has Been Reached
“Replace the Lamp Cartridge” is displayed on the screen for 10 seconds in
a 1-minute interval.
Please replace the lamp with a new one.
See “Replacing the Lamp Cartridge” on Page E-61 for information about
lamp cartridge replacement.
• When Over 100 Hours Have Elapsed Since Reaching Lamp Life
(Including Low Mode)
[Warning!! System Shutdown] is displayed for 10 seconds and the power is
switched off. Pressing the STANDBY button under this condition will not
switch on the power. Please replace the lamp cartridge.
E-57
When an Indicator is Lit or Flashing
The indicators on the projector’s control panel light or flash to
notify of problems, as described below.
An indicator is also used to notify you of the currently set power
mode (under normal circumstances). See “Power Cable Connections and Switching the Power On/Off” on page E-21.
STATUS indicator
US
AT
ST
Y
DB
AN
ST
Y
DB
STANDBY indicator
AN
ST
TO
AU
Indicator status
STATUS
STANDBY
STATUS
STANDBY
STATUS
STANDBY
Lit red
When the power is on (Lit green)
Standby (Lit amber)
Flashing amber for 60 seconds, then lit
amber
Flashing red
(lit for 1 seconds/off for 1 seconds)
The lamp cover is open.
The lamp cover is not properly mounted. Mount it properly.
Lit red
Flashing red
(lit for 0.5 seconds/off for 0.5 seconds)
STANDBY
Lit red
STANDBY
STATUS
STANDBY
It is time to replace the lamp.
Replace with a new lamp cartridge.
The lamp has reached the end of its service life. The power
will no longer turn on.
The projector can be used for 100 hours after the lamp has reached
the end of its service life.
Replace with a new lamp cartridge.
Lit red
STATUS
STATUS
What you should do
Flashing red
(lit for 0.5 seconds/off for 0.5 seconds)
The temperature is abnormally high.
• The temperature protector has been activated. If the room temperature is high, move the projector to a cool place. If the
projector’s internal temperature is high, check the cooling fan’s
ventilation slots and clean them if they are clogged.
• When the temperature protector is activated, the power turns
off and in some cases will not turn back on immediately. In this
case wait about 90 seconds, then try again.
The fan has stopped.
Unplug the power cable and contact a store that sells the XD70U
for repairs.
Lit amber
Flashing red
(lit for 1 seconds/off for 1 seconds)
When the lamp has burned out during use
Flashing amber for 90 seconds, then lit amber
When the lamp does not come on from the start
Lit amber
The lamp will not light.
Wait at least 90 seconds, then turn the power back on. If the
problem persists, unplug the power cord and contact a store
that sells the XD70U for repairs.
Should an indicator be in a condition other than normal or flash at a rate other than the aforementioned, disconnect the power
cable and contact your store of purchase.
Thermal Protector
When the temperature inside the projector becomes abnormally high, the STATUS indicator flashes red (0.5 seconds on/0.5
seconds off), the STANDBY indicator is a steady red, and at the same time the temperature protector operates and switches off
the power of the projector.
Should this happen, please take the following actions.
1. Switch off the power and disconnect the power plug from the wall outlet.
2. Check the following matters and take the required measures.
When the projector is being used in a location that has a high ambient temperature, set it up again in a cool location. Check the
outflow and intake holes and clean them if they are obstructed.
3. Wait about 60 minutes until the temperature of the projector drops.
If after having performed the above matters, the problem still has not been solved, please contact your store of purchase.
E-58
Troubleshooting
Check the following matters before requesting servicing.
Problem
Power does not turn on
Reference
Page
Check
• Is the power cord plugged into a power outlet?
• Is the lamp cover properly mounted?
• Is the projector’s temperature high? To protect the projector, the power cannot be turned on when the projector’s temperature is abnormally high.
• Has the lamp reached the end of its service life?
E-58
Is a connected input selected?
Is the cable properly connected to the input terminal?
When a computer is connected, are signals being output from the computer?
Does the signal being input have a frequency usable with this projector?
Are the brightness and contrast adjusted to the minimum?
Is the STATUS indicator lit a steady red or flashing red?
When the component signal of the DVD player is connected with the RGB
connector and the image is not output, is [Input Settings] of the RGB connector properly selected?
• For a RGB input, has the picture been properly adjusted?
E-26
E-16 –19
E-57
E-65
E-44
E-58
E-53
Image is distorted
• Is the projector properly installed?
• For trapezoidal (keystone) distortion, perform keystone adjustment.
Please note that depending on the projected picture and the projection conditions, it may not be possible to eliminate keystone distortion completely.
E-24
E-50
Image is out of focus
•
•
•
•
Is the lens properly focused?
Are the screen and projector installed at the proper distance?
Does the projection distance exceed the focusing range?
Is there condensation on the lens, etc.?
If the projector is moved from a cool storage area to a warm place and the
power is turned on, condensation may form on the lens or internal optical
parts. If this happens, wait until the condensation has evaporated before
using the projector.
E-25
E-15
E-15
–
Image is not in proper position and is not displayed
properly
• For a computer input, are the horizontal and vertical positions properly adjusted?
• Does the input signal have a compatible resolution and frequency? Check
the computer’s resolution.
E-45
Video image is crushed
• If the image is crushed in the horizontal or vertical direction or if it is not
displayed over the entire screen, select a different aspect ratio.
E-27
Colors of the overall image
are strange
• When a component signal is being input, is the color space setting proper?
• For a composite input, is the hue properly adjusted?
E-47
E-44
Characters flicker or colors
are offset for RGB inputs
• From the menu, select “Image” and adjust the clock frequency and phase.
E-44, 45
Cannot select the menu
name
• Other than [Settings], [Option] and [Information], selection will not be possible unless a signal is being input to the projector and the image/picture is
projected.
–
Remote control unit does
not operate
• Are the remote control unit’s batteries worn? Replace with new batteries.
• Is there an obstacle between the remote control unit and the projector’s
remote control signal sensor?
• Is the remote control unit outside of range?
• Are you pointing the remote control unit’s transmitter towards the projector’s
remote control signal sensor?
E-12
E-13
• See “When an indicator is lit or flashing”.
E-58
No image is produced
STATUS indicator is lit red
or flashing red
•
•
•
•
•
•
•
E-21
E-63
E-58
E-59
E-44, 45
E-65
E-13
E-13
Cleaning
• Be certain to disconnect the power plug from the power outlet before cleaning.
• Do not spray or otherwise expose the projector, lens, or screen to volatile substances such as insecticides. Do not leave rubber
or vinyl products in contact with the projector for long periods. Doing so could cause them to undergo qualitative changes or the
coatings may peel, etc.
Cleaning a Soiled Projector Main Unit
• Wipe with a lint-free, soft, dry cloth.
When very dirty, wipe with a cloth that has been moistened with a diluted neutral detergent, then finish with a dry cloth. If a
chemically-treated cloth is going to be used, please follow any written warnings.
• Do not wipe with thinner, benzene, or other solvents. Doing so could cause them to undergo qualitative changes or the coatings
may peel, etc.
• When removing the dust of the outflow and intake holes, use the brush attachment on a vacuum cleaner to clean out the dust.
Avoid using the vacuum directly without attaching the adapter as well as the use of a nozzle adapter.
• Do not scratch or otherwise hit the projector body with your nails or other hard object, since this will cause scratches.
Dirty Lens
• Clean using the same method you would use to clean a camera lens: Use a commercial blower for camera use or cleaning
paper for eye glasses. Be careful not to scratch the lens at this time.
Dust of the Intake and Outflow Holes
Dust that collects in the intake and outflow holes will obstruct the ventilation and cause the internal temperature to rise which
could cause damage. Clean this area carefully. As a guideline, clean at least every 100 hours of usage.
• Switch off the power, check that the
STANDBY indicator has changed to
a steadily lit amber, then unplug the
power cable.
• Clean out the holes from the outside
using a vacuum cleaner. Use the
brush adapter of the vacuum cleaner
to do this. Avoid using the vacuum
directly without attaching the adapter
as well as the use of a nozzle adapter.
ST
AT
US
AN
ST
DB
Y
Y
DB
AN
ST
TO
AU
CE
R
G
B
S
V
ID
E
O
V
ID
E
O
A
U
D
IO
M
O
U
S
E
P
C
C
O
N
TR
O
L
UR
SO
Cleaning the Inside of the Projector
Cleaning of the inside of the projector is required about once a year. Failure to clean over a long period while dust has collected
inside the projector could cause a fire or breakdown. Do not clean the inside of the projector by yourself. Please be sure to contact
your dealer.
E-60
Replacing the Lamp Cartridge
• The lamp that is used as a light source in the projector has a limited service life. The rated service life of the lamp is
about 2000 hours (when used in normal mode only). This could be shortened depending on conditions of use and
other factors.
Note that lamp life will be extended when the projector is often used in Low mode. (The rated service life of the lamp
means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from
test conditions at this company.)
• When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp
Cartridge] is displayed on the screen. When this occurs, it is time to replace the lamp cartridge. Please make the
replacement following the procedure below.
• If the projector is used another 100 hours after the lamp’s service life is reached, the power is set to the standby mode
and no longer turns on.
• Contact a store that sells the XD70U for a replacement lamp. Indicate you need a VLT-XD70LP replacement lamp for
the XD70U (order code 41T-577).
CAUTION
• Replacement of the lamp cartridge is performed after switching off the power, waiting for the cooling fan to stop,
disconnecting the power plug from the power outlet, and then leaving the projector for about 60 minutes before
replacement is started. Replacement of the lamp cartridge during operation or immediately after operation stops will
cause burns because of the high temperature.
• Do not remove any screws other than those specified.
• Do not touch the lamp with bare hands. Doing so could shorten the life of the lamp.
• If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can
be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may
cause injury. If this happens, contact your dealer or the store the projector was purchased.
CAUTION
This projector uses a lamp that contains mercury.
Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance :
www.eiae.org
E-61
Replacing the Lamp Cartridge
Preparations: Turning the projector upside-down on top of a soft cloth, etc., so that it does not get scratched makes it easier to
replace the lamp cartridge. Turn the projector right-side up after replacing the lamp cartridge.
1 Unplug the power cord.
2 Turn the projector upside-down.
3 Remove the lamp cover.
(1) Turn the lamp cover’s set screw counterclockwise and
loosen until the screw turns freely. (The screw does
not come off.)
(2) Open the lamp cover a little, then pull it in the direction of the arrow and remove it.
4 Remove the lamp cartridge.
(1) Turn the lamp cartridge’s screw counterclockwise and
loosen them until the screw turn freely. (The screw
do not come off.)
(2) Grasp the lamp cartridge’s handle and pull upward
to remove the lamp cartridge.
E-62
Replacing the Lamp Cartridge
5 Mount the new lamp cartridge.
(1) Push the lamp cartridge in slowly.
(Line it up with the screw holes in the projector.)
(2) Turn the lamp cartridge screw clockwise to tighten
them.
6 Mount the lamp cover.
(1) Set the tip of the lamp cover in place, then close the
lamp cover.
(2) Turn the lamp cover’s screw clockwise to tighten it.
7 Reset the Lamp Timer.
Connect the power cable, switch on the power, and then reset.
Select [Info.] → [Lamp Timer Reset] on the menu and press the ENTER button. There is a change to the initialization
verification display. Press the ENTER button again. See “Lamp Timer Reset” on Page E-56.
Note:
After reaching the lamp service life, if the lamp is used for more than another 100 hours, it will not be possible to switch on the power. Should
this happen, while the projector is in the standby mode, simultaneously holding down the projector’s SOURCE button and AUTO button for
more than 5 seconds will clear the lamp timer. Checking that the STATUS indicator is out will show that the lamp timer has been cleared.
Contact a store that sells the XD70U for a replacement lamp. Indicate you need a VLT-XD70LP replacement lamp for the XD70U (order code
41T-577).
E-63
Specifications
Model
XD70U
Optical
Method of projection :
DMD
Lamp
Projection lens :
Image size
Light Output
Contrast Ratio
DLP™ (single chip DMD)
0.7 inches 1024⳯768 dots
200 W high pressure mercury lamp
Manual zoom (⳯1.2), Manual focus F = 2.6 – 2.9, f = 18.4 – 22.1 mm (f = 0.72 – 0.87 inch)
Minimum: 38.4 inch (at projection distance of 1.2m(3.9 feet) telephoto)
Maximum: 300 inch (at projection distance of 8.0m(26.2 feet) wide)
Standard mode: 2000 lumens
2000:1 (Full on/off)
Electrical
Inputs
Color Reproduction
Resolution
Input Current
Power Requirement
Power Consumption
Video (NTSC3.58/NTSC4.43/PAL/PAL-N/PAL-M/PAL60/SECAM/YCbCr(NTSC, PAL)/
YPbPr(480p, 576p, 1080i, 720p)): (automatic or manual switching)
RGB (Horizontal :15 to 80 kHz, Vertical 50 to 85 Hz)
Full color (16,770,000 colors)
VGA (640⳯480) expansion/true, S-VGA (800⳯600) expansion/true
XGA (1024⳯768) true, S-XGA (1280⳯1024) compression
2.8/1.4 A
100 – 120/220 – 240 V AC, 50/60 Hz
280 watts (250 watts in Low mode)
Mechanical
Dimensions Excluding Stand
Weight
Operational Temperatures
216 mm (W)⳯60 mm (H)⳯252 mm (D) (not including protrusion)
8.5 in.(W)⳯2.4 in.(H)⳯10.3 in.(D) (not including protrusion)
Approximately 2.0 kg / 4.4 lbs
Data projector: 5° to 35°C (41° to 95°F), 30 to 85% humidity
• Specifications and design are subject to change without notice.
E-64
Table of Supported Frequency
The projector automatically identifies the signal input from the computer and selects the optimum resolution as shown on the table
below.
Manual adjustments may be required for some input signals. See “Picture Adj. / Fine Picture / H Position / V Position” on page E44, 45.
Signal
VIDEO(NTSC)
VIDEO(PAL/SECAM)
VESA
Apple Macintosh
HDTV (1080i)
SDTV
(720p)
(576p)
(480p)
Resolution
ⳮ
ⳮ
640
640
720
640
640
720
720
640
640
640
640
800
800
800
800
800
1024
1024
1024
1024
1024
1280
640
823
1024
1152
1920
1920
1280
720
720
⳯ 350
⳯ 350
⳯ 350
⳯ 400
⳯ 400
⳯ 400
⳯ 400
⳯ 480
⳯ 480
⳯ 480
⳯ 480
⳯ 600
⳯ 600
⳯ 600
⳯ 600
⳯ 600
⳯ 768
⳯ 768
⳯ 768
⳯ 768
⳯ 768
⳯ 1024
⳯ 480
⳯ 624
⳯ 768
⳯ 870
⳯ 1080
⳯ 1080
⳯ 720
⳯ 576
⳯ 480
Frequency
Horizonral (kHz)
15.734
15.625
31.5
37.9
31.5
31.5
37.9
31.5
37.9
31.5
37.9
37.5
43.3
35.2
37.9
46.9
48.1
53.7
48.4
56.5
57.7
60.0
68.7
64.0
35.0
49.7
60.2
68.7
33.8
28.1
45.0
31.3
31.5
Vertical (Hz)
60.0
50.0
70.1
85.1
70.0
70.1
85.1
70.0
85.0
60.0
72.8
75.0
85.0
56.3
60.3
75.0
72.2
85.1
60.0
70.1
72.0
75.0
85.0
60.0
66.7
74.5
74.9
75.1
60.0
50.0
60.0
50.0
60.0
* The projector does not support the ADC connector on Apple Macintosh.
Video
嘷
嘷
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
嘷
嘷
嘷
嘷
嘷
嘷
ⳮ
RGB
XGA
SVGA
ⳮ
ⳮ
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
ⳮ
嘷
嘷
嘷
嘷
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
ⳮ
嘷
嘷
嘷
嘷
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
: Supported frequency
: Not supported frequency
The display resolution is 1024⳯768 dots. When displaying a signal with resolutions other than 1024⳯768 dots such as 1280⳯1024,
sizes of characters or lines may be uneven.
E-65
Cabinet Dimensions
SOURCE
AUTO
STANDBY
STANDBY
252 (9.9)
STATUS
60 (2.4)
216 (8.5)
Unit: mm (inch)
E-66
MITSUBISHI ELECTRIC CORPORATION
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan