Samsung RC120MHXGA Unit installation

EHS mono_RC***MHXGA_IM_E_34411A(2).indd 50
2012-04-06 오전 8:59:15
RC✴✴✴MHXGA
RC✴✴✴MHXEA
Air to Water Heat Pump
Mono Outdoor Unit
installation manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/register
E S F I P D DB98-34411A(2)
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 51
2012-04-06 오전 8:59:16
Contents
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Product specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Application examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Main components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Piping work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Testing operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cylinder unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Safety precautions
Carefully follow the precautions listed as below because they are essential to guarantee the safety of SAMSUNG product.
WARNING
• Always disconnect a power supply of Air-Water Heat Pump before servicing it or accessing
components inside the unit.
• Verify that installation and testing operations shall be performed by qualified personnel.
• To prevent serious damage on the system and injuries to users, precautions and other
notices shall be observed.
Warning
ffCarefully read the content of this manual before installing the air to water heat pump and store the manual in a safe place
in order to be able to use it as reference after installation.
ffFor maximum safety, installers should always carefully read the following warnings.
ffStore the operation and installation manual in a safe location and remember to hand it over to the new owner if the air
conditioner is sold or transferred.
ffStore the user and installation manual in a safe location and remember to hand it over to the new owner if the air to
water heat pump is sold or transferred.
ffThis manual explains how to install Air-Water Heat Pump. The use of other types of units with different control systems
may damage the units and invalidate the warranty. The manufacturer shall not be responsible for damages arising from
the use of non compliant units.
ffThe air conditioner is compliant with the requirements of the Low Voltage Directive (72/23/EEC), the EMC Directive
(89/336/EEC) and the Directive on pressurized equipment (97/23/EEC).
ffThe manufacturer shall not be responsible for damage originating from unauthorized changes or the improper
connection of electric and hydraulic lines. Failure to comply with these instructions or to comply with the requirements
set forth in the “Operating limits” table, included in the manual, shall immediately invalidate the warranty.
ffFailure to comply with these instructions or to comply with the requirement on the Operating Range (Heat: -20~25°C/
Cool: 10~46°C) set forth in the Product Specification (p.5) shall immediately invalidate the warranty.
ffDo not use the units if you see some damages on the units and recognize something bad such as loud noisy, smell of
burning.
ffIn order to prevent electric shocks, fires or injuries, always stop the unit, disable the protection switch and contact
SAMSUNG’s technical support if the unit produces smoke, if the power cable is hot or damaged or if the unit is very noisy.
ffAlways remember to inspect the unit, electric connections, refrigerant tubes and protections regularly. These operations
shall be performed by qualified personnel only.
ffThe unit contains moving parts and electrical parts, which should always be kept out of the reach of children.
2
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 2
2012-04-06 오전 8:57:26
ENGLISH
ffDo not attempt to repair, move, alter or reinstall the unit by unauthorized personnel, these operations may cause product
damage, electric shocks and fires.
ffDo not place containers with liquids or other objects on the unit.
ffAll the materials used for the manufacture and packaging of the air to water heat pump are recyclable.
ffThe packing material and exhaust batteries of the remote controller(optional) must be disposed of in accordance with
local regulations.
ffThe air to water heat pump containing a refrigerant must be disposed in authorized center or returned to retailer as
special wastes.
ffWear protective gloves to unpack, move, install, and service the unit to avoid your hands being injured by the edge of the
parts.
ffDo not touch the internal parts (water pipes, refrigerant pipes, heat exchangers, etc) while running the units. And if you
need to adjust and touch the units, have enough time for the unit can be cooled and be sure to wear protective gloves.
ffIn case of refrigerant leakage, try to avoid getting in contact with the refrigerant because this could result in severe
wounds.
ffWhen you install the Air to water heat pump in a small room, you must consider a proper ventilation to prevent a leakage
level within the maximum permissible limit.
-- In that case, you may die from suffocation by some possibility.
ffMake sure to safely dispose of packing materials. Packing materials, such as nails and other metal or wooden pallets may
cause children get injured.
ffInspect the product shipped and check if damaged during transport. If the product has some damages, DO NOT INSTALL
and immediately discuss about the damages with the carrier or retailer (if the installer or the authorized technician has
collected the material from the retailer.)
ffOur units shall be installed in compliance with the spaces described in the installation manual, to ensure accessibility
from both sides and allow repairs or maintenance operations to be carried out. If the units installed without complying
with procedures described in manual, additional expenses can be asked because special harnesses, ladders, scaffolding
or any other elevation system for repair service will NOT be considered part of the warranty and will be charged to the
end customer.
ffAlways make sure that the power supply is compliant with local safety standards.
ffVerify that the voltage and frequency of the power supply comply with the specifications and input power is sufficient to
ensure the operation of any other domestic appliance connected to the same electric lines. Always verify that the cut-off
and protection switches are suitably selected.
ffAlways verify that electric connections (cable entry, section of leads, protections…) are compliant with the electric
specifications and with the instructions provided in the wiring scheme. Always verify that all connections comply with
the standards applicable to the installation of air to water heat pumps. Devices disconnected from the power supply
should be completely disconnected in the condition of overvoltage category.
ffDo not connect the earth wire to the gas pipe or water pipe, lighting rod, surge absorber, or telephone earth wire. If
earthing is not complete, it may cause an electric shock or fire.
ffBe sure to install both an earth leakage detector and circuit breaker with specified capacity in accordance with relevant
local and national regulations.
-- If it is not installed properly, it may cause electric shocks and fire.
ffMake sure that the condensed water runs well out of the unit at low ambient temperature. Drain pipe and cond heater
can frost/ice can not grow. If drain work is not effective for releasing condensed water, it can make the units get damaged
by massive ice and system can be stop , covered by ice.
ffInstall the power cable and communication cable of the indoor and outdoor unit at least 1m away from the electric
appliance.
ffProtect the unit from rats or small animals. If an animal makes a contact with the electric parts, it can cause malfunctions,
smoke or fire. Please instruct the customer to keep the area around the unit clean.
3
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 3
2012-04-06 오전 8:57:26
Product specifications
Product line-up
Line-up
Remark
Chassis
Heat pump units
Model name
Auxiliary parts
RC120MHXEA
RC120MHXGA
RC140MHXEA
RC140MHXGA
RC160MHXEA
RC160MHXGA
RC090MHXEA
-
MIM-E03A
Requisite
Standard models:
NH200CHXEA
NH300CHXEA
Option
Control kit
Cylinder unit
Accessories
ffKeep supplied accessories until the installation is finished.
ffHand the installation manual over to the customer after finishing installation.
ffThe quantities are indicated in parentheses.
Installation manual (1)
Drain plug (1)
Fastener-nut(1)
Rubber-cover wire(2)
Drain cap (1)
4
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 4
2012-04-06 오전 8:57:28
Type
Unit
RC090MHXEA
Power source
-
1P, 220~240VAC 50Hz
RC120MHXEA
RC120MHXGA
RC140MHXEA
RC140MHXGA
RC160MHXEA
RC160MHXGA
1P, 220~240VAC 50Hz 1P, 220~240VAC 50Hz 1P, 220~240VAC 50Hz
3P, 380~415VAC 50Hz 3P, 380~415VAC 50Hz 3P, 380~415VAC 50Hz
kg
83
113
113
113
-
Rotary inverter
Rotary inverter
Rotary inverter
Rotary inverter
Condenser
-
Brazing type
48 plates
Brazing type
72 plates
Brazing type
72 plates
Brazing type
72 plates
Evaporator
-
Ø7, FP 1.6, L850
Ø7, FP 1.7, L950
Ø7, FP 1.7, L950
Ø7, FP 1.7, L950
Fan & Motor
-
Propeller, Ø520,
3-blade
BLDC Inverter
Propeller, Ø520,
3-blade
BLDC Inverter
Propeller, Ø520,
3-blade
BLDC Inverter
Propeller, Ø520,
3-blade
BLDC Inverter
Flow switch
LPM
Base heater
W
150
150
150
150
Refrigerant
g
1,400 (R410A)
2,200 (R410A)
2,200 (R410A)
2,200 (R410A)
Noise
(Heat/Cool, Pressure)
dBA
63/ 60
64/62
64 / 62
64 / 62
Water connection
(In/Out)
Inch
1.0 / 1.0
1.0 / 1.0
1.0 / 1.0
1.0 / 1.0
Leaving water
temperature
°C
Cooling : 5 ~ 25
Heating : 25 ~ 55
Cooling : 5 ~ 25
Heating : 25 ~ 55
Cooling : 5 ~ 25
Heating : 25 ~ 55
Cooling : 5 ~ 25
Heating : 25 ~ 55
Operating range
(Heat/Cool)
°C
-20~35 / 10~46
-20~35 / 10~46
-20~35 / 10~46
-20~35 / 10~46
ENGLISH
Weight(Kg)
Compressor
16 ± 1.5
16 ± 1.5
16 ± 1.5
16 ± 1.5
Magnetic (decreasing) Magnetic (decreasing) Magnetic (decreasing) Magnetic (decreasing)
Weight (net)
Kg
83
113
113
113
Size (WxHxD, net)
mm
940 x 998 x 330
940 x 1,420 x 330
940 x 1,420 x 330
940 x 1,420 x 330
5
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 5
2012-04-06 오전 8:57:28
Application examples
WARNING
• The application examples given below are for illustration purposes only.
• When the SAMSUNG Air-to-Water Heat Pump system is used in series with another heat source (e.g. gas
boiler), ensure that the return water temperature not exceed 55°C.
• The unit is only to be used in a closed water system. Application in an open water circuit can lead to excessive
corrosion of the water piping.
• SAMSUNG can not be put responsible for incorrect or unsafe situations in the water system. Make sure that the
boiler, radiators, convectors, solar collectors, UFHs, FCUs, additional pumps, pipings, and controls in the water
system are in accordance with relevant local laws and regulations under the installer's responsibility.
• By-pass valve shall be installed for space heating loops. When one of loops or all loops are closed , water flow
rate could be low condition. To keep flow rate approximately and prevent flow stop, the by-pass valve shall be
installed between supply collector and return collector.
• SAMSUNG shall not be held liable for any damage resulting from not observing this rule.
• SAMSUNG do not provide Specific Pressure relief valve and flow switch. Installers and end-users shall consider
how to install the above parts in overall water system. If pressure relief valve and flow switch are not installed
in appropriate position, the water system can not be operated as designed.
Application #1
Mono outdoor + Control kit
Outdoor
Mechanical room
Indoor
TT
r
cto
lle
co
lar
So
Zone controller #2
DHW sensor input
& Booster heater output
Air-vent
45°C
Solar pump
TT
EE
Solar signal input
Supply header
50 ~ 55°C
Booster
heater
Return header
Back up boiler operation
output
DHW tank
Radiators or convectors
Wired controller
Zone Controller #1
Shut-Off &
Drain valve
Control Kit
Secondary
pump
Primary
pump 3-way valve
Strainer
Outdoor unit
Pressure
relief valve
3.0 bar
RR
Y
Primary EE
pump
Expansion
tank
Mixing Tank
40°C
Supply header
Return header
Air-vent
Under- Floor Heating Coils
Drain
6
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 6
2012-04-06 오전 8:57:29
Application #2
Mono outdoor + Cylinder unit
RF Receiver
Wired controller
Return header
From city water
Control Kit
(provided by SAMSUNG)
Room thermostat
(Wireless)
Hot water Supply
P
Radiators or convectors
ENGLISH
Expansion Vessel
Supply header
T
F
Room thermostat (option)
(Wired)
Supply header
Return header
Under-floor heating coils
Indoor 
Outdoor 
Outdoor unit
Cylinder unit
7
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 7
2012-04-06 오전 8:57:31
Main components
Dimensions(Overall)
Heat pump for R410A.
1-Fan chassis
ffRC090MHX✴
(Unit : mm)
384
330
360
620
675
528
537
998
973
940
2-Fan chassis
ffRC120MHX✴/RC140MHX✴/RC160MHX✴
(Unit : mm)
360
384
330
620
1420
1395
940
8
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 8
2012-04-06 오전 8:59:00
RC120MHX/RC140MHX/RC160MHX
Dimensions
(Water pipe)
RC090MHX
RC090MHX✴
RC120MHX/RC140MHX/RC160MHX
RC120MHX✴/RC140MHX✴/RC160MHX✴
RC090MHX
ENGLISH
513.4
513.4
151.5
244.4
151.5
244.4
(Unit : mm)
83.5
(Unit : mm)
(Unit : mm)
(Unit : mm)
83.5
(Unit : mm)
(Unit : mm)
9
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 9
2012-04-06 오전 8:59:03
Main components
RC090✴
③
②
①
NO.
Name
Note.
①
PHE
48P
②
Base heater
SUS316L, 150W
③
Water fitting
BSPP 1" Male
10
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 10
2012-04-06 오전 8:59:04
RC120✴/RC140✴/RC160✴
ENGLISH
①
④
⑤
③
②
NO.
Name
Note.
①
PHE
72P
②
Base heater
SUS316L, 150W
③
Water hose in
Rubber hose
④
Water hose out
Rubber hose
⑤
Water fitting
BSPP 1" Male
11
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 11
2012-04-06 오전 8:59:04
Functional diagram
RC090MHX✴/RC120MHX✴/RC140MHX✴/RC160MHX✴
4WAY
v/v
T/S #6
HP s/w
T/S #1(TW1)
S/V
S/V
PHE
T/S #2(TW2)
T/S #4
T/S #3
Comp
Filter
Exp. v/v
Accum
T/S #5
Filter
Part
Description
PHE
Plate heat exchanger
T/S #1
For water outlet temp sensor
T/S #2
For water inlet temp sensor
T/S #3
For PHE out temp
T/S #4
For discharge temp
T/S #5
For cond temp
T/S #6
For ambient temp sensor
S/V
Service valve ¼ inch
Accum
Accumulator
TW2
PHE inlet water temperature
TW1
PHE outlet water temperature
12
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 12
2012-04-06 오전 8:59:05
Installing the unit
Moving the outdoor unit
ENGLISH
ffSelect the moving route in advance.
ffBe sure that moving route is safe from weight of the outdoor unit.
ffDo not slant the product more than 30˚when carrying it. (do not lay the product down sideways)
ffThe surface of the heat exchanger is sharp. Be carefule not to be injured while moving and installing.
Moving the outdoor unit by wire rope
ffFasten the outdoor unit by two 8m or longer wire ropes as shown at the
figure. To prevent from damage or scratches, insert a piece of cloth between
the outdoor unit and rope, then move the unit.
Wire rope
Plate protection
cloth
❋❋ The appearance of the unit may be
differ ent from the picture depending
on the model.
Moving the outdoor unit with a fork lift
ffInsert the fork into the wooden pallet at the bottom of the outdoor unit
carefully. Be careful that the fork does not damage the outdoor unit.
Wooden pallet
Fork lift
13
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 13
2012-04-06 오전 8:59:05
Installing the unit
Deciding on where to install the outdoor unit
Decide the installation location regarding the following condition and obtain the user’s approval.
ffThe outdoor unit must not be placed on its side or upside down, as the compressor lubrication oil will run into the cooling
circuit and seriously damage the unit.
ffChoose a location that is dry and sunny, but not exposed to direct sunlight or strong winds.
ffDo not block any passageways or thoroughfares.
ffChoose a location where the noise of the Air to Water Heat Pump when running and the discharged air do not disturb
any neighbours.
ffChoose a position that enables the pipes and cables to be easily connected to the other hydrauric system.
ffInstall the outdoor unit on a flat, stable surface that can support its weight and does not generate any unnecessary noise
and vibration.
ffPosition the outdoor unit so that the air flow directly stream towards the open area.
ffPlace the outdoor unit where there are no plants and animals because they may cause malfunction of outdoor unit.
ffMaintain sufficient clearance around the outdoor unit, especially from a radio, computer, stereo system, etc.
ffWhen installing the outdoor unit near seashore, make sure it is not directly exposed to sea breeze. If you can not find an
adequate place without direct sea breeze, make sure to apply anti-corrosion coating on the heat exchanger.
ffInstall the outdoor unit in a place (such as near buildings etc.) where it can be prevented from sea breeze which can
damage the outdoor unit.
Sea breeze
Outdoor
unit
Sea breeze
Sea
Outdoor
unit
Sea
ffIf you cannot avoid installing the outdoor unit by the seashore, construct a protection wall around to block the sea
breeze.
Protection wall
Outdoor
unit
Sea breeze
• Protection wall should be constructed with a solid material such
as concrete to block the sea breeze and the height and the width
of the wall should be 1.5 times larger than the size of the outdoor
unit. Also, secure over 700mm between the protection wall and
the outdoor unit for exhausted air to ventilate.
Sea
ffInstall the outdoor unit in a place where water can drain smoothly.
❋❋ If you cannot find a place satisfying above conditions, please contact manufacturer. Make sure to clean the sea water
and the dust on the outdoor unit heat exchanger.
14
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 14
2012-04-06 오전 8:59:06
CAUTION
CAUTION
Do not install the outdoor unit in a snowy and cold area (low temperature and high humidity area - where the
temperature is below -7°C and humidity is higher than 85%) because according to operation condition (defrost,
etc.), ice may be formed in the drain route.
If the ice is accumulated, it may cause critical damage to the product.
ex) lakeside of cold area in winter time, seashore, alpine region and etc.
ENGLISH
ffDo not install the Air to Water Heat Pump in following places.
• The place where there is mineral oil or arsenic acid. There is a chance that parts may get damaged due to burned resin.
The capacity of the heat exchanger may reduce or the Air to Water Heat pump may be out of order.
• The place where corrosive gas such as sulfurous acid gas generates from the vent pipe or air outlet. The copper pipe or
connection pipe may corrode and refrigerant may leak.
• The place where there is a danger of existing combustible gas, carbon fiber or flammable dust. The place where thinner
or gasoline is handled.
• This device must be installed according to the national electrical rules.
• With an outdoor unit having net weight upper than 60kg, we suggest do not install it suspended on wall, but
considering floor standing one.
ffIf the outdoor unit is installed at a height, ensure that its base is firmly fixed in position.
ffMake sure that the water dripping from the drain hose runs away correctly and safely.
ffWhen you install the outdoor unit at wayside, you should install it above 2m height or make sure that the heat from the
outdoor unit shouldn't be in direct contact with passersby. (The ground for application :The revision of regulation for
facility in building by the law of the Ministry of Construction and Transportation.
15
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 15
2012-04-06 오전 8:59:06
Installing the unit
Space requirements for outdoor unit
When installing 1 outdoor unit
❋❋ When the air outlet is towards the wall
2,000 or more
600 or more
300 or more
❋❋ The upper part of the outdoor unit and the air outlet
is towards the wall
1,500 or more
600 or more
❋❋ When 3 sides of the outdoor unit are blocked by the
wall
300 or more
300 or more
1,500 or more
300 or more
❋❋ When the air outlet is opposite the wall
1,500 or more
300 or more
(Unit : mm)
❋❋ The upper part of the outdoor unit and the air outlet
is opposite the wall
❋❋ When front and rear side of the outdoor unit is
towards the wall
16
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 16
2012-04-06 오전 8:59:06
When installing more than 1 outdoor unit
ENGLISH
1500 or more
(Unit : mm)
300 or more
❋❋ When the air outlet is towards the wall
300 or more
600 or more
600 or more
600 or more
600 or more
600 or more
❋❋ When front and rear side of the outdoor unit is towards the wall
1500 or more
600 or more
3000 or more
3000 or more
500 or
more
300 or more
500 or
more
1500 or more
300 or more
❋❋ When 3 sides of the outdoor unit are blocked by the wall
300 or more
❋❋ The upper part of the outdoor unit and the
air outlet is opposite the wall
300 or more
❋❋ When front and rear side of the outdoor unit is towards the wall
CAUTION
• The units must be installed according to distances declared, in order to permit accessibility from each side, either
to guarantee correct operation of maintenance or repairing products. The unit’s parts must be reachable and
removable completely under safety condition (for people or things).
17
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 17
2012-04-06 오전 8:59:06
Installing the unit
Outdoor unit installation
The outdoor unit must be installed on a rigid and stable base to avoid any increase in the noise level and vibration,
particularly if the outdoor unit is to be installed in a location exposed to strong winds or at a height, the unit must be fixed to
an appropriate support(wall or ground).
ffFix the outdoor unit with anchor bolts.
CAUTION
(Unit : mm)
344
• When tightening the anchor bolt, tighten the rubber washer
to prevent the outdoor unit bolt connection part from
corroding.
• Make a drain outlet around the base for outdoor unit
drainage.
• If the outdoor unit is installed on the roof, you have to check
the ceiling strength and waterproof the unit.
384
Anchor bolt hole
328
NOTE
• The anchor bolt must be 20mm or higher from the base
surface.
620
940
Outdoor unit support
Soft rubber designed to cut off vibration
from rack to wall. (not supplied with
product)
Outdoor
unit
Anchor bolt
20mm
Designed to cut off residual vibration from
outdoor unit to rack. (not supplied with
product)
Outdoor unit
support
Base surface
ffOutdoor unit installed on the wall by rack
-- Ensure the wall will be able to suspend the weight of rack and outdoor unit ;
-- Install the rack close to the column as much as possible ;
-- Install proper grommet in order to reduce noise and residual vibration transferred by outdoor unit towards wall.
CAUTION
When installing air guide duct
• Check and make sure that screws do not damage the copper pipe.
• Secure air guide duct on guard fan.
18
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 18
2012-04-06 오전 8:59:07
Drain work
While Air-Water Heat Pump is running in heating mode, Ice can begin accumulate on the surface of condenser.
To prevent Ice from growing, system go into De-frost mode and then Ice on the surface changes to water.
Dropped water from condenser shall be eliminated through running drain holes to prevent Ice growing at low temperature.
WARNING
≥100mm
ENGLISH
ffIn case there is not enough space for drainage out of the unit, additional drain
works are required. Follow the description as below
-- Make space more than 100mm between the bottom of the outdoor unit and
the ground for installation of the drain hose.
-- Insert the drain plug into the hole on the bottom of the outdoor unit.
-- Connect the drain hose to the drain plug.
-- Make sure dusts or small branches should not go into the drain hose.
• If drain work is not enough, it can lead to system performance degration and system damages.
Drain hole Ø20 x 4ea
Air discharge side
30 mm
Drain plug x 1ea
Drain cap x 3ea
1. Prepare a water drainage channel around the foundation, to drain waste water from around the unit.
2. If the water drainage of the unit is not easy, please build up the unit on a foundation
of concrete blocks, etc. (the height of the foundation should be maximum 150mm).
3. If you install the unit on a frame, please install a waterproof plate within 150mm of
the underside of the unit in order to prevent the invasion of water from the lower
direction.
4. When installing the unit in a place frequently exposed to snow, pay special attention
to elevate the foundation as high as possible.
5. If you install the unit on a building frame, please install a waterproof plate (field
supply) (within 150mm of the underside of the unit) in order to avoid the drain
water dripping. (See figure)
19
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 19
2012-04-06 오전 8:59:08
Installing the unit
Selecting a location in cold climates
NOTE
• When operating the unit in a low outdoor ambient temperature, be sure to follow the instructions described
below.
ffTo prevent exposure to wind, install the unit with its suction side facing the wall.
ffNever install the unit at a site where the suction side may be exposed directly to wind.
ffTo prevent exposure to wind, install a baffle plate on the air discharge side of the unit.
ffIn heavy snowfall areas it is very important to select an installation site where the snow will not affect the unit. If lateral
snowfall is possible, make sure that the heat exchanger coil is not affected by the snow (If necessary construct a lateral
canopy)
1. Construct a large canopy.
2. Construct a pedestal.
-- Install the unit high enough off the ground to prevent it being buried under
snow.
ffThe outdoor unit should be installed with consideration of the direction of strong winds. These can make the unit turn
over, so the side of the unit should be set to face the wind, not the front of the unit.
Strong wind
Strong wind
blown air
20
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 20
2012-04-06 오전 8:59:09
Piping work
CAUTION
ENGLISH
Water connections must be made in accordance with the outlook diagram delivered with the unit, respecting the water
in- and outlet. If air, moisture or dust gets in the water circuit, problems may occur. Therefore, always take into account the
following when connecting the water circuit:
ffUse clean pipes only.
ffHold the pipe end downwards when removing burrs.
ffCover the pipe end when inserting it through a wall so that no dust and dirt enter.
ffUse a good thread sealant for the sealing of the connections.
The sealing must be able to withstand the pressures and temperatures of the system.
ffWhen using non-brass metallic piping, make sure to insulate both materials from each other
to prevent galvanic corrosion.
ffBecause brass is a soft material, use appropriate tooling for connecting the water circuit.
Inappropriate tooling will cause damage to the pipes.
• Be careful not to deform the unit piping by using excessive force when connecting the piping. Deformation of
the piping can cause the unit to malfunction.
• Always use two wrenches (spanners) for tightening or loosening the water connections, and tighten
connections with a torque wrench as specified in below table. If not, connections and parts can be damaged
and leaks.
• The unit is only to be used in a closed water system. If applications are in open water circuit, it will generate Heat
exchangers fouling, Corrosion, Leak.
Name
Tightening torque
1
BSPP1
350~380 kgf•cm
34 ~ 37 N•m
2
Flow switch
72~82 kgf•cm
7 ~ 8 N•m
Flushing and air-purging
When filling water, the following start-up procedure should be followed.
1. All system components and pipes must be tested for the presence of leaks.
2. Preparation of a make-up water assembly or flushing unit is recommended for installation
and service.
3. Before connecting pipes to the hydro unit, flush water pipes clean to remove contaminants
during hours using a flushing unit or tap water pressure if it is adequate (at 2 to 3 bar)
4. Fill water into the hydro unit by opening service valves.
5. Purge the air. (Fill with a flushing unit with sufficient capacity: avoid aerating the water)
6. Circulate for long enough to ensure that all air has been bled from the complete water
piping system.
CAUTION
• After installations, commissioning should be performed by qualified
representatives. Unless flushing and air-purging works are performed
adequately, it might result in malfunctions.
Flushing unit
(or purging cart)
21
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 21
2012-04-06 오전 8:59:10
Piping work
CAUTION
• Before installing/commissioning the unit, make sure to check the following points :
-- The maximum water pressure of the unit is 2.8 bar static pressure.
-- The operating range of water temperature is 15~55˚C at heating conditions and 5~25˚C at cooling
conditions.
-- The minimum required water flow for operation is 16 liters/min. At all times the required water flow-rates
should remain. Otherwise, the unit can stop due to a lack of water.
-- Water quality must be according to EN directive 98/83 EC.
-- If the unit and the pipes are exposed to freezing temperature, It can cause damage to the hydraulic system.
Special care must be taken to prevent freezing of the total water system.
-- The unit is designed to be used in a closed-loop system. Do not use any other components which are designed
only for a open-loop system.
-- Never use Zn-coated parts in the water circuit.
-- All hydraulic parts including field piping must be insulated to reduce heat loss and condensation.
-- It is recommended to install the make-up water assembly to feed small quantities of water to the system
automatically, replacing the minor water losses and maintaining the system pressure.
-- Drain taps must be provided at all low points of the system to permit complete drainage of the circuit for
maintenance use.
-- Make sure that the check valves are correctly installed in the system (field supply).
-- Flush pipes out with clean water to remove contaminants in pipes during installation.
-- The strainer(water filter) must be cleaned after flushing the pipes, and it should be cleaned periodically.
Replace strainer when necessary.
-- Charging : Charge the water until a pressure of 1.5~2.0bar by using make-up water assembly(Field supply).
(The water pressure indicated on the manometer will vary depending on the water temperature)
The nominal water pressure in the system should remain about 1.0 bar at all times to avoid air entering the
water system.
-- Air purging; Make sure that air should be vented from the system at start-up or after installing/ servicing.
The air vent valve must be opened during charging the water (at least 2 turns) in order to removeall air in the
circuit, and a make-up water assembly allows water into the system continuosly.
-- In case that the water piping would be located in a higher position than the air vent of the unit, it is necessary
to add an additional ones in the highest position of water circuit. The air vent should be located both where
water temperatures are the highest and where the height of pipes are the highest.
-- Always use materials which are compatible with water used in the system and with the materials used on the
indoor unit.
-- Select piping diameter in relation to required water flow and available ESP of the pump.
-- Use chemical cleaning agents(Begin with acid , finish with alkali).
-- Do not operate the system with closed valves because it results in damaging the heat pump.
22
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 22
2012-04-06 오전 8:59:10
Freeze protection
Frost can make some damage on the hydraulic system. It is because it is installed outside house nomally. To avoid taking risks
of freezing problem, special cares such as Anti-freezing fluid are required as below. Ethylene glycol concentration can vary
depeding on outdoor temperature where our system is installed, fill in Ethylene glycol by mixing as below.
Outdoor temperature
Ethylene Glycol(%)
23°F (–5°C)
10
14°F (–10°C)
20
5°F (–15°C)
25
–10°F (–20°C)
35
ENGLISH
WARNING
Ethylene Glycol Is Toxic
Ethylene glycol is toxic if swallowed, and therefore is a hazard to animals and small children.
Ethylene glycol must be handled in accordance with relevant local laws and regulations.
Setting capacity and pre-pressure of the expansion vessel
2.5
Pre-pressure(bar)
When it is required to change the default pre-pressure of
the expansion vessel(1 bar), keep in mind the following
guidelines:
ffUse only dry nitrogen to set the expansion vessel prepressure.
ffInappropriate setting of the expansion vessel
pre-pressure will lead to malfunction of the system.
Therefore, the pre-pressure should only be adjusted by a
licensed installer.
2.0
1.5
Operation range
1.0
0.5
0.0
150
200
250
300
350
Total water volume(ℓ)
Installation height
difference(a)
Water volume
< 220 Litres
> 220 Litres
<7m
No pre-pressure adjustment required.
Actions required:
• Pre-pressure must be decreased, calculate
according to “Calculating the pre-pressure of
the expansion vessel”.
• Check if the water volume is lower than
maximum allowed water volume.
>7m
Actions required:
• Pre-pressure must be increased, calculate the
appropriate value following by “Calculating
the pre-pressure of the expansion vessel”.
• Check if the water volume is lower than
maximum allowed water volume.
Expansion vessel of the unit too small for the
installation.
(a) Installation height difference: height difference(m) between the highest point of the water circuit and the indoor unit. If
the unit is located at the highest point of the installation, the installation height is considered 0m.
Calculating the pre-pressure of the expansion vessel
ffThe pre-pressure(Pg) to be set depends on the maximum installation height difference(H) and is calculated as below :
Pg=(H/10+0.3) bar
23
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 23
2012-04-06 오전 8:59:10
Piping work
Unit resistance and PHE resistance by glycol concentrate
The unit is composed of water pipes and PHE basically.
To ensure correct operation and predict the expected performance, Flow and Resistance table can be used and Flow and
Resistance characteristic is dependent on Glycol concentration.
RC090✴✴
200
180
160
140
kPa
120
100
80
60
40
20
0
0
10
20
30
40
50
60
70
80
90
WATER
EG 10%
EG 20%
EG 40%
EG 45%
LPM
RC120/140/160✴✴
200
180
160
140
kPa
120
100
80
60
40
20
0
0
10
20
30
40
50
60
70
80
90
WATER
EG 10%
EG 20%
EG 40%
EG 45%
LPM
Changing Glycol concentration can cause the pressure drop of the system and it can leads to make flow rate rather slow. Just
in case performance degration, installer shall be careful of flow rate changes.
24
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 24
2012-04-06 오전 8:59:10
Flow switch
Flow switch is not integrated part in MONO Unit. But the installation is essential to operate MONO Unit.
Flow switch is provided by Samsung control kit as a sub component.
CAUTION
ENGLISH
• Flow switch shall be installed described by installation manual of Mono unit or Control kit.
• All electric wiring works shall be implemented by manuals which Samsung provided.
• Before completing the installation works, make sure to check if the flow switch is installed in horizontal and
if flow direction is in parallel with pipe direction. (Straight length of In and Out pipe of flow switch shall have
5 times length in diameter)
Charging water
After installation is completed, the following procedures shall be used to charge water into the hydro unit.
ffConnect water lines to water connections of Air-Water Heat Pump.
ffAir vent valve shall be open at least 2turns so that air can be eliminated
in the system.
Water Oulet
ffOpen the service valve in the water supply connection.
ffWater pressure of supply line shall be over 2.0 bar for good charging
Water Inlet
work.
ffStop water supply when the pressure gauge of hydro unit indicates
RC160✴✴
around 2.0 bar.
CAUTION
RC090✴✴
• There shall be enough space for Service works.
• Water pipe and connections shall be cleaned by using water or cleaner before operating the unit at first time.
• Considering E.S.P and water pump performance, select water plumbing specification and under floor loofs.
• Make sure to calculate the total resistance of piping system and determine the size of pipes before selecting the
required head of pumps. If the pressure loss of total water system is over than designed pressure, an external
water pump shall be installed on piping system in series.
• Do not connect power supply while water is charging.
• When initial installation or re-installation is required, remove air by air vent valve in water plumbings which are
installed by local installers to prevent air trap in the system while charging water.
• Make sure that back flow preventer (check valves) shall be installed on main supply line to prevent from
contaminating the city water.
-- It is recommended to install the make-up water assembly to prevent from contaminating the city water.
-- Check valves in the make-up water assembly can prevent running water inside hydro unit from contaminating
water supplies during installation or maintenance works.
25
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 25
2012-04-06 오전 8:59:10
Piping work
Pressure relief valve
MONO Unit does not have a pressure relief valve. The valve shall prevents abnomal water pressure from damaging the the
system by opening at 3.0 bar.
• Make certain that the discharged water out of drain pan does not affect other elements.
CAUTION
Filter / Strainer
Installation of Filter / Strainer is mandatory for water system. The Filter or Strainer shall be located in front of inlet pipe of PHE.
While operating the system, some dust and foreign materials can circulate the system and can make the whole system not
work well due to blockage of heat exchangers and corrosion in some components.
Filter mesh : #30
Piping insulation
The complete water circuit, inclusive all piping, must be insulated to prevent condensation during cooling operation and
reduction of the heating and cooling capacity as well as prevention of freezing of the outside water piping during winter
time. The thickness of the sealing materials must be at least 9 mm with (0.035 W/mK) in order to prevent freezing on the
outside water piping.
If the temperature is higher than 86°F (30°C) and the humidity is higher than RH 80%, then the thickness of the sealing
materials should be at least 20 mm in order to avoid condensation on the surface of the sealing.
26
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 26
2012-04-06 오전 8:59:10
Wiring
CAUTION
• During the unit installation make first refrigerant connections and then electrical connections. If unit is
uninstalled first disconnect electrical cables, then refrigerant connections.
• Connect the air conditioner to grounding system before performing the electrical connection.
• When installing the unit, you shouldn't use inter connection wire.
ENGLISH
Two electronic cables must be connected to the outdoor unit.
ffThe connection cord between indoor unit and outdoor unit.
ffThe power cable between outdoor unit and auxiliary circuit breaker.
ffSpecially for Russian and European market, before installation, the supply authority should be consulted to determine the
supply system impendance to ensure compliance.
Example of EHS system
When using ELB for 1 phase
MCCB
1Ø
Power cable
Communication cable
ELB
or
Outdoor Unit
Communication cable
ELCB
1Ø
ELCB(30A)
Grounding
Control kit
1Ø
Grounding
When using ELB for 3 phase 4 wires
MCCB
3Ø
Power cable
Communication cable
ELB
or
Outdoor Unit
Communication cable
ELCB
3Ø
ELCB(30A)
Grounding
Control kit
Power cable (1Ø)
1Ø
Grounding
❋❋ If an outdoor unit is installed in a place in danger of an electric leak or submergence, you must install the ELB.
❋❋ Installation of control kit must be followed its Installation manual.
27
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 27
2012-04-06 오전 8:59:11
Wiring
Power Cable Specifications
1 phase
Rated
Voltage Range
Outdoor unit
MCA
MFA
Fuse cut-off
current
Maximum
MCA✴1.25 +
Current in normal
Total fuse in unit
Additional Load
operation
Hz
Volts
Min
Max
RC090MHXEA
50
220-240
198
264
22 A
27.5 A
40 A
RC120MHXEA
50
220-240
198
264
28 A
35 A
40 A
RC140MHXEA
50
220-240
198
264
30 A
37.5 A
40 A
RC160MHXEA
50
220-240
198
264
32 A
40 A
40 A
ffThe power cable is not supplied with air conditioner.
ffSupply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible cord (Code
designation IEC:60245 IEC 57 / CENELEC:H05RN-F)
ffEquipment complying with EN/IEC 61000-3-12.
Indoor Unit
Load
Power supply
No Heater
(Water Pump, Valve, Wired RMC)
MIM-E03A
Booster Heater (3kw)
Booster Heater (~3kw)
+ Backup Heater (~3kw)
1Ø, 220-240V,
50Hz
Power cable
MAX. length
mm2,wires
m
A
1.5 / 3
<10m
10
2.5 / 3
10m<L<20m
10
4.0 / 3
<10m
20
6.0 / 3
10m<L<20m
20
6.0 / 3
<10m
40
8.0 / 3
10m<L<20m
40
Type GL
ffThe Power cable is not supplied with the heat pump.
ffFor power cable, use the grade H07RN-F materials in 1Ø system.
ffIf you connect Backup Heater at separated power cable, you can reduce wire size. (Please refer to indoor unit installation
manual)
28
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 28
2012-04-06 오전 8:59:11
3 Phase
Rated
Voltage Range
Outdoor unit
MCA
MFA
Fuse cut-off
current
Volts
Min
Max
RC120MHXGA
50
380-415
342
457
10 A
12.5 A
25 A
RC140MHXGA
50
380-415
342
457
11 A
13.8 A
25 A
RC160MHXGA
50
380-415
342
457
12 A
15 A
25 A
ENGLISH
Maximum
MCA✴1.25 +
Current in normal
Total fuse in unit
Additional Load
operation
Hz
ffThe power cable is not supplied with air conditioner.
ffSupply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible cord (Code
designation IEC:60245 IEC 57 / CENELEC:H05RN-F)
ffThis equipment complies with IEC 61000-3-12 provided that the short-circuit power Ssc is greater than or equal to
3.3[MVA] at the interface point between the user's supply and the public system. It is the responsibility of the installer or
user of the equipment to ensure, by consultation with distribution network operator if necessary, that the equipment is
connected only to a supply with a short-circuit power Ssc greater than or equal to 3.3[MVA].
29
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 29
2012-04-06 오전 8:59:11
Wiring
Between indoor unit and outdoor unit connection cable specifications(Common in use)
Communication cable
Home server
0.75mm², 2wires
0.75mm², 2wires
ffFor Indoor Power Cable, use the grade H07RN-F or H05RN-F materials.
When installing the indoor unit in a computer room or network room, use the
double shielded (Tape aluminum / polyester braid + copper ) cable of FROHH2R
type.
1-phase terminal block spec
AC power : M5 screw
Communication : M4 screw
L
15
N
9.95
12
3-phase terminal block spec
AC power : M4 screw
L1(R) L2(S) L3(T)
9.95
Communication : M4 screw
N
11.55
9.95
30
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 30
2012-04-06 오전 8:59:12
Wiring diagram of power cable
When using ELB for 1 phase and 3 phase
ff1 phase
ENGLISH
L
N
Cable tie
Power Supply
Electrical component box
MCCB
ELB
Main power cable
MCCB
Communication cable
ff3 phase
L1(R) L2(S) L3(T)
N
Indoor Unit
ffThe appearance of the unit may be different
from the picture depending on the model.
Cable tie
3 Phase 4 Wires power
cable (AC 380V)
CAUTION
Communication
cable
• You should connect the power cable into the power cable terminal and fasten it with a clamp.
• The unbalanced power must be maintained within 2% of supply rating.
-- If the power is unbalanced greatly, it may shorten the life of the condenser. If the unbalanced power is
exceeded over 4% of supply rating, the indoor unit is protected, stopped and the error mode indicates.
• To protect the product from water and possible shock, you should keep the power cable and the connection
cord of the indoor and outdoor units within ducts. (with appropriate IP rating and material selection for your
application)
• Ensure that main supply connection is made through a switch that disconnects all poles, with contact gap of a
least 3 mm.
• Devices disconnected from the power supply should be completely disconnected in the condition of
overvoltage category.
• Keep distances of 50mm or more between power cable and communication cable.
31
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 31
2012-04-06 오전 8:59:12
Wiring
Wiring diagram of connection cord
1 phase
3 phase
L
N
Control kit
L
N
F2
F1
L
Control kit
L1(R) L2(S) L3(T)
N
F2
F1
N
NOTE
F2
Cable
tie
Cable
tie
Main power cable
F1
Communication cable
3 Phase 4 Wires power
cable (AC 380V)
Communication
cable
• Lay the electrical wiring so that the front cover does not rise up when doing wiring work and attach the
front cover securely.
• Ground wire for the indoor unit and outdoor unit connection cable must be clamped to a soft copper
tin-plated eyelet terminal with M4 screw hole (NOT SUPPLIED WITH UNIT ACCESSORIES).
Connecting the power terminal
ffConnect the cables to the terminal board using the compressed ring terminal.
ffCover a solderless ring terminal and a connector part of the power cable and then connect it.
Silver solder
32
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 32
2012-04-06 오전 8:59:12
d1
16 (0.02)
25 (0.03)
35 (0.05)
50 (0.07) 70 (0.10)
8 (3/16)
8 (3/16)
8 (3/16)
8 (3/16)
8 (3/16)
22 (7/8)
24 (1)
16
(10/16)
±0.2
(±0.007)
12 (1/2)
16.5
(10/16)
16
(10/16)
22 (7/8)
±0.3 (±0.011)
±0.3 (±0.011)
9 (3/8)
11.5 (7/16)
13.3 (1/2)
+0.3
(+0.011)
-0.2
(-0.007)
+0.5 (+0.019)
-0.2 (-0.007)
+0.5 (+0.019)
-0.2 (-0.007)
5.8 (1/4)
7.7 (5/16)
9.4 (3/8)
Allowance [mm(inch)]
±0.2 (±0.007)
±0.2
±0.2
(±0.007) (±0.007)
±0.2 (±0.007)
±0.2 (±0.007)
Min. [mm(inch)]
6 (1/4)
7.9 (5/16) 9.5 (5/16)
11 (3/8)
12.5 (1/2)
E
F
Min. [mm(inch)]
5 (3/16)
L
Max. [mm(inch)]
20 (3/4)
9 (3/8)
9 (3/8) 13 (1/2)
28.5
30 (133 (1(1-1/8)
3/16)
5/16)
Standard dimension
8.4 (18.4 (18.4 (14.3 (3/16)
[mm(inch)]
3/16)
3/16)
3/16)
d2
+ 0.2
+0.4
+0.4
+0.4
Allowance [mm(inch)] (+0.007) (+0.015) (+0.015) (+0.015)
0(0)
0(0)
0(0)
0(0)
1.15
1.45
t
Min. [mm(inch)]
0.9 (0.03)
(0.04)
(0.05)
15 (5/8)
13 (1/2)
34 (1-3/8)
13 (1/2)
43 (111/16)
38 (1-1/2)
8.4 (1-3/16)
8.4 (1-3/16)
+0.4 (+0.015)
0(0)
+0.4 (+0.015)
0(0)
1.7 (0.06)
1.8 (0.07)
±0.3
±0.4
(±0.011) (±0.011)
17.5
13.5 (1/2)
(11/16)
+0.5
+0.5
(+0.019) (+0.019)
-0.2
-0.4
(-0.007) (-0.015)
11.4
13.3 (1/2)
(7/16)
+0.3
(+0.011)
±0.4
(±0.015)
-0.2
(-0.007)
17.5
18.5 (3/4)
(11/16)
14 (9/16) 20 (3/4)
50 (2)
ENGLISH
Nominal dimensions for
4/6 (0.006/0.009) 10 (0.01)
cable [mm2(inch)]
Nominal dimensions for
4 (3/8) 8 (3/16) 8 (3/16)
screw [mm(inch)]
Standard dimension
9.5 (3/8) 15 (9/16) 15 (9/16)
[mm(inch)]
B
±0.2
Allowance [mm(inch)]
±0.2 (±0.007)
(±0.007)
Standard dimension
5.6 (1/4)
7.1 (1/4)
[mm(inch)]
+0.3
D
+0.3 (+0.011)
(+0.011)
Allowance [mm(inch)]
-0.2 (-0.007)
-0.2
(-0.007)
Standard dimension
3.4 (1/8)
4.5 (3/16)
[mm(inch)]
51 (2)
8.4 (18.4 (13/16)
3/16)
+0.4
+0.4
(+0.015) (+0.015)
0(0)
0(0)
2.0
1.8 (0.07)
(0.078)
ffConnect the rated cables only.
ffConnect using a driver which is able to apply the rated torque to the screws.
ffIf the terminal is loose, fire may occur caused by arc. If the terminal is connected too firmly, the terminal may be
damaged.
Tightening Torque (kgf • cm)
CAUTION
M4
12.0~15.0
M5
20.0~25.0
Communication : F1, F2
3phase AC power : L1(R), L2(S), L3(T), N
1phase AC power : L, N
• When connecting cables, you can connect the cables to the electrical part or connect them through the holes
below depending on the spot.
• Run transmission wiring between the indoor and outdoor units through a conduit to protect against external
forces, and feed the conduit through the wall together with refirgerant piping.
• Remove all burrs at the edge of the knock-out hole and secure the cable to the outdoor knock-out using lining
and bushing with an electrical insulation such as rubber and so on.
• Must keep the cable in a protection tube.
• Keep distances of 50mm or more between power cable and communication cable.
• When the cables are connected through the hole, remove the Plate bottom.
33
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 33
2012-04-06 오전 8:59:12
Testing operations
1. Check the power supply between the outdoor unit and the auxiliary circuit breaker.
• 1 phase power supply : L, N
• 3 phases power supply : R,S,T,N
2. Check the CONTROL KIT
1) Check that you have connected the power and communication cables correctly. (If the power cable and
communication cables one mixed up or connected incorrectly, the PCB will be damaged.)
2) Check the temp. sensor, drain pump/hose, and display are connected correctly.
3. Press K1 or K2 on the outdoor unit PCB to run the test mode and stop.
KEY
K1
KEY operation
7-segment display
Press once : Heating test run
" " " " "BLANK" "BLANK"
Press twice : Defrost test run
" " " " "BLANK" "BLANK"
Press 3times : Finishing test mode
-
Press once : Cooling test run
K2
" " " " "BLANK" "BLANK"
Press twice : Finishing test mode
K3
Reset
K4
View mode
-
7-segment display
Refer to View mode display
KEY (K1~K4)
ON
1 2 3 4
5 6
7 8
4. View Mode : When the K4 switch is pressed, you can see information about our system state as below.
Number of
press
Display contents
Display
Segment 1
Segment 2
Segment 3
Segment 4
Units
0
Communication State
1s digit of Tx
10s digit of Rx
1s digit of Rx
1
Order frequency
1
100s digit
10s digit
1s digit
Hz
2
2
100s digit
10s digit
3
0
10s digit
1s digit
0 : split
1 : mono
1s digit
Hz
4
Current frequency
Type of Outdoor unit
(Mono/Split)
Outdoor air sensor
5
Discharge sensor
5
10s digit
1s digit
°C
6
PHE (Eva) sensor
6
+/-
10s digit
1s digit
°C
7
Cond sensor
7
+/-
10s digit
1s digit
°C
8
Current
8
10s digit
1s digit
First decimal
9
Fan RPM
Target discharge
temperature
EEV
9
1000s digit
100s digit
10s digit
A
100s digit
10s digit
1s digit
°C
B
1000s digit
100s digit
10s digit
step
3
10
11
10s digit of Tx
4
+/100s digit
0
°C
A
rpm
34
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 34
2012-04-06 오전 8:59:13
Number of
press
12
Segment 1
Segment 2
C
0
Not used exchanger
capacity
Protection control
Segment 3
Segment 4
0
0
Frequency state
0 : Normal
1 : Hold
2 : Down
3 : Up_limit
4 : Down_limit
Units
kW
D
0 : air
conditioning
1 : heating
Protection
control
0 : no protection
control
1 : freezing
2 : non-stop
defrosting
3 : over-load
4 : discharge
E
100s digit
10s digit
1s digit
°C
F
set
-
100s digit
10s digit
1s digit
long-1
Temperature of Heatsink
at PBA
The Quantity of
connected Indoor Unit
Main Micom version
Year(Hex)
Month(Hex)
Day(two digit)
Day(One digit)
-
long-1and 1
Inverter Micom version
Year(Hex)
Month(Hex)
Day(two digit)
Day(One digit)
-
long-1and 2
EEPROM version
Year(Hex)
Month(Hex)
Day(two digit)
Day(One digit)
-
14
15
ENGLISH
13
Display
Display contents
5. DIP Switching setting
KEY
ON (default)
OFF
Remark
K5
Auto Address
(Outdoor unit recognize the address of indoor
unit by random access.)
Manual Address
(Outdoor unit recognize the address of indoor
unit by rotary switch of indoor unit.)
In Monobloc K5
must be'ON'
K6
Operating time of base heater is 15min.
Operating time of base heater is 20min.
Base heater will
operate under 0°C
K7
Anti-stack snow mode ON
Anti-stack snow mode OFF
K8
Enable base heater
K9
Silence operation
K10
Disable base heater
K9
ON
ON
OFF
OFF
K10
ON
OFF
ON
OFF
Mode
Disable silence mode
Silence mode Step.1
Silence mode Step.2
Silence mode Step.3
K11
X
K12
X
K13
K14
Whole current control
K13
ON
ON
OFF
OFF
K14
ON
OFF
ON
OFF
Not defined
Not defined
Mode
Limit total current: 1_Down
Limit total current: 1_Down_OP1
Limit total current: 1_Down_OP2
Limit total current: 1_Down_OP3
K15
X
Not defined
K16
X
Not defined
35
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 35
2012-04-06 오전 8:59:13
Trouble shooting
WARNING
• Incorrect handling of thermostat, safety valve or other valves may lead to tank rupture. When servicing the unit
follow instructions carefully:
• Always turn off main power supply when water supply is being shut off.
• Test the free operation of the safety valve regularly by opening the valve ensuring the water flows freely.
• Electrical connection and all servicing of the electrical components should only be carried out by an authorized
electrician.
• Fitting and all servicing of plumbing fixtures should only be carried out by an authorized installer.
• When replacing the thermostat, safety valve or any other valve or part supplied with this unit, use only approved
parts of the same specification.
Error codes
If the unit has some problems and does not work normally, error code is shown on the OUTDOOR UNIT main PBA or LCD
of the wired remote controller.
Display
Explanation
Error Source
101
CONTROL KIT / OUTDOOR UNIT wire connection error
CONTROL KIT,
OUTDOOR UNIT
162
EEPROM Error
CONTROL KIT
201
CONTROL KIT/OUTDOOR UNIT communication error (Matching error)
CONTROL KIT,
OUTDOOR UNIT
202
CONTROL KIT/OUTDOOR UNIT communication error (3 min)
CONTROL KIT,
OUTDOOR UNIT
203
Communication error between INVERTER and MAIN MICOM (6 min)
OUTDOOR UNIT
221
OUTDOOR UNIT temperature sensor error
OUTDOOR UNIT
231
Condenser temperature sensor error
OUTDOOR UNIT
251
Discharge temperature sensor error
OUTDOOR UNIT
320
OLP sensor error
OUTDOOR UNIT
403
Detection of OUTDOOR UNIT compressor freezing (During cooling operation)
OUTDOOR UNIT
404
Protection of OUTDOOR UNIT when it is overload (during Safety Start, Normal
operation state)
OUTDOOR UNIT
416
Discharge of a compressor is overheated
OUTDOOR UNIT
419
OUTDOOR UNIT EEV operation error
OUTDOOR UNIT
425
Power source line missing error (only for 3-phase model)
OUTDOOR UNIT
440
Heating operation blocked (outdoor temperature over 35°C)
OUTDOOR UNIT
441
Cooling operation blocked (outdoor temperature under 9°C)
OUTDOOR UNIT
458
OUTDOOR UNIT fan1 error
OUTDOOR UNIT
461
[Inverter] Compressor startup error
OUTDOOR UNIT
462
[Inverter] Total current error/PFC over current error
OUTDOOR UNIT
463
OLP is overheated
OUTDOOR UNIT
36
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 36
2012-04-06 오전 8:59:13
Display
Explanation
Error Source
[Inverter] IPM over current error
OUTDOOR UNIT
465
Compressor V limit error
OUTDOOR UNIT
466
DC LINK over/low voltage error
OUTDOOR UNIT
467
[Inverter] Compressor rotation error
OUTDOOR UNIT
468
[Inverter] Current sensor error
OUTDOOR UNIT
469
[Inverter] DC LINK voltage sensor error
OUTDOOR UNIT
470
EEPROM read/write error
OUTDOOR UNIT
471
[Inverter] OTP error
OUTDOOR UNIT
474
IPM(IGBT Module) or PFCM temperature sensor Error
OUTDOOR UNIT
475
OUTDOOR UNIT fan2 error
OUTDOOR UNIT
484
PFC Overload Error
OUTDOOR UNIT
485
Input current sensor error
OUTDOOR UNIT
500
IPM is overheated
OUTDOOR UNIT
554
Gas leak error
OUTDOOR UNIT
601
Communication error between the CONTROL KIT and wired remote controller
Wired Remote
Controller
602
Wired remote controller Master/Slave setting error
Wired Remote
Controller
604
Communication tracking error between the CONTROL KIT and wired remote controller
CONTROL KIT,
Wired Remote
Controller
607
Communication error between the Master and Salve wired remote controllers
Wired Remote
Controller
901
Water inlet (PHE) temperature sensor error(open/short)
OUTDOOR UNIT
902
Water outlet (PHE) temperature sensor error(open/short)
OUTDOOR UNIT
903
Water outlet (backup heater) temperature sensor error.
CONTROL KIT
904
DHW tank temperature sensor error
CONTROL KIT
906
Refrigerant gas inlet (PHE) temperature sensor (open/short)
OUTDOOR UNIT
911
Flow switch and water pump error (F/S signal is OFF for 10 sec. during the water pump
signal is ON)
CONTROL KIT
912
Flow switch and water pump error (Water pump signal is OFF for 60sec during the F/S
signal is ON)
CONTROL KIT
ENGLISH
464
37
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 37
2012-04-06 오전 8:59:13
Maintenance
Listed checks and inspections shall be implemented regularly so that the unit can operate as design intention in production
site.
Always switch off the unit and remove power cable from the electric source before carrying out any maintenance or repair
works.
Mentioned actions shall be carried out at least once a year by qualified personnel.
1. Water pressure
• Check if the water pressure is above 0.3 bar. If necessary, supplement water.
2. Water filter
• Use water filter which is available for cleaning and clean it regularly.
3. Water pressure relief valve
• Check for correct operation of the pressure relief valve.
-- The valve will work over the designated pressure.
-- If there is leakage of water or water splashed in normal condition, please contact your local installer.
4. Glycol
• Record and check the glycol concentration and the pH-value in the system at least once a year.
-- A Ph-valve below 8.0 indicates that a significant portion of the inhibitor has been depleted and that more inhibitor
needs to be added.
-- When the Ph-value is below 7.0 then oxidation of the glycol occurred, the system should be drained and flushed
thoroughly before severe damage occurs.
-- Make sure that the disposal of the glycol solution is done in accordance with relevant local and national regulation.
Using service valve
To open the service valve
1. Open the cap and turn the stop valve counterclockwise by using a hexagonal
wrench.
2. Turn it until the axis is stopped.
NOTE
• Do not apply excessive force to the stop valve and always use special
instruments. Otherwise, the stopping box can be damaged and the
back sheet can leaks.
• If the watertight sheet leaks, turn the axis back by half, tighten the
stopping box, then check the leakage again. If there is no leakage any
more, tighten the axis entirely.
Body Cap
Spindle
O-Ring
3. Tighten the cap securely.
To close the service valve
1.
2.
3.
4.
Remove the cap.
Turn the stop valve clockwise by using a hexagonal wrench.
Tighten the axis until the valve reached the sealing point.
Tighten the cap securely.
CAUTION
• When you use the service port, always use a charging hose, too.
• Check the leakage of refrigerant gas after tightening the cap.
• Must use a spanner and wrench when you open/tighten the service valve.
38
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 38
2012-04-06 오전 8:59:13
Adding refrigerant
The Heat Pump unit is provided to users with basic amounts of refrigerants as initial setting values. While using the unit or
doing refrigerant piping works, there can be some loss of refrigerants compared to initial amounts. To run the units properly,
keep the amount of refrigerant which SAMSUNG designated.
Procedures as below is describing how to adding the amount of refrigerant.
• R410A Shall be added as liquid phase.
• Adding and recharging works shall be by Service valves.
ENGLISH
WARNING
1. Connect the manifold gauge and purge the manifold gauge.
2. Open the manifold gauge valve of the liquid side service valve and add the liquid refrigerant.
3. If you cannot fully recharge the additional refrigerant while the outdoor unit is stopped, use the key on PCB in the Heat
Pump to run for recharging the remaining refrigerant.
Adding refrigerants in running condition
1.
2.
3.
4.
Press the function key for adding refrigerant.
After 30 minutes of operation, open the service valve on low pressure side in Heat Pump.
Open the valve for low pressure side in the manifold gauge to recharge the remaining refrigerant.
After completing, close the valves in manifold gauge and eliminate the hoses from service valves.
Manifold gauge
High pressure side
Low pressure side
Low pressure side
High pressure side
Service valve
Scale
Important information regulation regarding the refrigerant used
CAUTION
• Inform user if system contains 3 kg or more of fluorinated greenhouse gases. In this case, it has to be checked
for leakage at least once every 12 months, according to regulation n°842/2006. This activity has to be covered
by qualified personnel only. In case situation above (3 kg or more of R-410A), installer (or recognised person
which has responsability for final check) has to provide a maintenance book, with all the information recorded
according to REGULATION(EC) N° 842/2006 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 17 May
2006 on certain fluorinated greenhouse gases.
39
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 39
2012-04-06 오전 8:59:14
Cylinder unit
Safety information
(Before installing a cylinder unit, please read this manual thoroughly to ensure that you know how to safely and efficiently
install a new appliance.)
WARNING
• If you don’t follow the safety precautions, you may get the risk of serious wound or death.
ffThe installation must be done by the manufacturer or its service agent or a qualified person in order to avoid a hazard.
-- Installation by an unqualified person may cause a water leakage, electric shock or fire and so on.
ffThe electric work must be done by service agent or qualified persons according to national wiring regulations and use
only rated cable.
-- Use certified power cable in the market suggested here and do electric work according to installation manual
otherwise, electric shock or fire may occur.
ffInstall the outdoor unit correctly according to the installation manual.
-- An incorrect installation may cause a water leakage, electric shock or fire and so on.
ffManufacturer is not responsible for accidents due to incorrect installation.
ffUse certified parts in the market and supplied parts from the factory.
-- All wiring, components and materials to be procured on the site must comply with the applicable local and national
codes. If you don’t use the certified parts and tools, it can cause trouble to the air conditioner and bring into injury.
ffInstall the cylinder unit on a hard and even place that can support its weight.
-- If the place cannot support its weight, the outdoor unit may fall down and it may cause injury.
ffFix the outdoor unit securely on foundation as it can fall over strong wind or earthquake.
-- If the outdoor unit is not properly fixed, it turns over and accidents may occur.
ffSecure power cable with a conduit, which is accessory part for cylinder unit, not to be pulled out by external force.
-- If fixing is incomplete, it can cause trouble with a heat generation, electric shock or fire and so on.
ffThe disinfection function field settings must be configured by the installer according to local laws and regulations.
ffAttach the service cover to the cylinder unit and outdoor unit securely without any gaps. If there are any gaps, there is
potential risk of fire or electric shock due to dust or water.
ffMake sure to earth the unit. Do not connect the earth wire to the gas pipe or water pipe, lighting rod, surge absorber, or
telephone earth wire. If earthing is not complete, It may cause an electric shock or fire.
40
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 40
2012-04-06 오전 8:59:14
General information
CAUTION
ENGLISH
ffSAMSUNG Eco Heating system with cylinder unit is designed to withstand SAMSUNG durability and reliability
requirements. We cannot guarantee neither good operation nor reliability of total system with other brand tanks.
ffThe piping, valves and system configuration of cylinder unit should be followed a relevant local or national regulations.
ffA pressure relief valve in accordance with an opening pressure of max. 0.9MPa should be connected.
ffThe electrical box must be opened by a licensed electrician.
ffSwitch off the power supply before opening the electrical box lid.
ffMake sure that the installation location of cylinder unit including piping and valves is frost free.
• Cylinder unit shall be located and installed indoors (garage, multipurpose room, boiler room).
• Always ensure that the ambient temperature around unit have to be above 0°C around the year.
• If the unit and the pipes are exposed to freezing temperature, It can cause damage to the hydraulic system.
Special care must be taken to prevent freezing of the total water system.
• If the unit stops for a long time because of a power supply failure, pump operating failure, or winter vacation,
drain all water from the system.
• Cylinder unit shall be always full of water. Check that water is fully filled with water by opening the pressure relief
valve. Air present in the water system may cause malfunction or fire.
• Water quality must be according to EN directive 98/83 EC.
• Make certain that back flow preventer (check valves) must be installed on main supply line to prevent from
contaminating the city water. It is recommended to install the make-up water assembly to prevent from
contaminating the city water. Check valves in the make-up water assembly can prevent running water inside
hydro unit from contaminating water supplies during installation or maintenance works.
• Before running the cylinder unit, check if valves are opened for inlet and outlet port of water pumps. And make
sure to have direction of valve slot be straight in horizontal.
(O)
(X)
41
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 41
2012-04-06 오전 8:59:14
Cylinder unit
Main components
④
⑥
⑤
③
⑦
⑧
①
②
⑨
Installed
Packaged
No.
1
2
3
4
5
6
7
8
9
-
Part
Water pump
2 Way valve
Control kit
Wired Remote Controller
RF Receiver
Air vent
Combination valve
Relief valve
Tundish
Expansion Tank
Wireless Thermostat
Qty
2
3
1
1
1
1
1
1
1
1
1
-
Flow Switch (16 lpm)
1
42
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 42
2012-04-06 오전 8:59:14
Water tank specifications
Detailed information for the DHW Tank are described in the following table.
Description
Volume capacity
Capacity
Electric element
Heating coil
Insulation
Insulation jacket
Dimensions
Connections
Weight
ℓ
NH300CHXEA
AISI 444 / DIN 1.4521
192
279
kW
3
Material
-
INCOLOY 825
Voltage
V/Hz
1P, 230~, 50
-
Duplex LDX 2101
Material quality
Heating Area
Material quality
Thickness
Material quality
m2
0.8
-
Polyurethane form
mm
40
-
Epoxy-coated mild steel – white
Vessel
mm
585 x 1130
585 x 1580
Net
mm
692 x 702 x 1200
692 x 702 x 1600
Packing
mm
800 x 900 x 1600
Cold water inlet
inch
BSPP 3/4"
Hot water outlet
inch
BSPP 3/4"
Recirculation
inch
BSPP 1/2"
Flow & Return
inch
BSPP 3/4"
Sensor pocket(s)
mm
ø8.05 mm inside, 1/2" thread
Overall
kg
Max. Water temperature
Other
Standard
NH200CHXEA
ENGLISH
Pressure vessel
Material quality
Unit
Packaging
Adjustable legs
800 x 900 x 2050
67
81
°C
70
-
Eco Foam - PUF
pcs
3
43
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 43
2012-04-06 오전 8:59:14
Cylinder unit
Space requirements
Positions of water inlet and outlet pipe are affected by the layout of cylinder unit. The layout of pipes and other components
except cylinder unit are the responsibility of installers. The cylinder unit must be laid out in accordance with the illustrations
as below to prevent any water leakage and malfunction.
ffObserve the clearances and dimensions as seen below during installing the water tank.
NOTE
• The installation space mentioned above is minimum suggested clearance.
• To secure enough service space and performance of system, take account of more sufficient space.
• Be sure to install unit in a place strong enough to withstand its weight.
[Total weight 365 kg, Tank(65 kg), Water(300 kg)]
30°
113°
110
220
475/630
H
296+h
33°
41°
48°
Volume
H
h
200
1130
800
300
1580
1250
44
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 44
2012-04-06 오전 8:59:14
Wiring diagram
CAUTION
• Turn on the cylinder unit and outdoor unit after completing electric wiring works.
• Do not disassemble the wirings out of the unit while the unit is operating.
• Circuit breaker shall be installed for safety and maintenance .
40.4
ENGLISH
ffMake sure of an earthing.
-- Do not connect the earth wire to the gas pipe, water pipe, lighting rod or telephone wire. If earthing is incomplete,
electric shock or fire may occur.
Wiring diagram
66T
1
1
4
4
2
Date code
Cal lot No.
59T 4117
2
59T
N
ø5.56
2 holes
L
42.52
50.8
63.5
Outer casing
Electrical connections – Technical Data:
Electric element
2.6 kW 230V 1 phase, 1 1/4” connection with O-ring seal
Adjustable
Electric output can be reduced by cutting one bridge on the element.
Thermostat
40~70°C (preset 60°C)
Safety cut-off
85°C
Electric central
Internally connected from factory. Splash proof IP21.
45
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 45
2012-04-06 오전 8:59:15
Cylinder unit
Switch box layout
Control Kit
46
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 46
2012-04-06 오전 8:59:15
Electrical connections
Procedure
WARNING
ENGLISH
• Switch off the power supply before making any connections.
• Use a thermal grease in temp. sensor pocket after installing electric connections.
• It is of great importance that the heater is filled with water before the electricity is hooked up, or else- the
warranty is not valid. If the heater is installed and not used, it must be flushed with water once a week.
• Be aware that the domestic hot water temperature at the hot water tap will be equal to the value selected in
field setting mode. If this high domestic hot water temperature can be a potential risk for human injuries, a
mixing valve (field supply) shall be installed at the hot water outlet connection of the domestic hot water tank.
This maximum allowable hot water temperature shall be selected according to local laws and regulations.
• Attach the service cover to the Hydro unit and cylinder unit securely without any gaps. If there are any gaps,
there is potential risk of fire or electric shock due to dust or water.
ffConnections to be made in the electrical box of cylinder unit
1. Connect the booster heater power supply and thermal protection cable.
2. Make sure to ensure strain relief of the cable.
47
EHS mono_RC***MHXGA_IM_E_34411A(2).indd 47
2012-04-06 오전 8:59:15