NVD Bullet Cameras

Installation Manual

3 Cameras in 1:

EV-1626-NKGQ

(NTSC)

EV-1626-PKGQ

(PAL)

EV-1626-NWGQ

(NTSC)

EV-1626-PWGQ

(PAL)

1

/

3

” Sony Super HAD CCD

12VDC/24VAC

2.8~12mm

6~50mm

OSD with service monitor port

600 TV lines

NVD Bullet Cameras have an ultra-low lux rating of 0.000006 allowing the camera to see in almost total darkness.

Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.

NVD Bullet Cameras

Specifications:

Type

CCD

Resolution

Pickup Elements

Video Output / Service Monitor Port

Video Output Format

Lens (DC Auto Iris)

Minimum Illumination

S/N Ratio

On Screen Display (OSD)

Motion Detection

Backlight Compensation

White Balance

Electronic Shutter

Auto Gain

3-DNR (DNR with 3D filtering)

Day & Night (Color)

Sharpness

Privacy

IP Rating

# of Infrared LEDs

Power Source

Current Draw

Operating Temperature

Dimensions (LxWxH)

Weight

Dimensions:

EV-1626-NKGQ (NTSC)

EV-1626-PKGQ (PAL

EV-1626-NWGQ (NTSC)

EV-1626-PWGQ (PAL)

IR LED Bullet Camera

1 /

3

” SONY Super HAD CCD

600 TV lines

NTSC: 768x494 pixels

PAL: 752x582 pixels

Composite video 1.0Vp-p into 75Ω + test connection

NTSC

2.8~12mm 6~50mm

0.000006-lux (LEDs on) 0.05-lux (LEDs off)

>52dB (weight on)

Built-in and controlled by internal joystick

4 zones

HLC/BLC/Off

ATW / AWC / MANUAL (1800°~10,500° K)

Auto/Manual (adjustable range: 1/60~1/120,000 sec)

Selectable: Low, Middle, High, Off

On/Off (adjustable range: 0~100)

Selectable: Color, Auto, B/W

On/Off (adjustable range: 0~31)

On/Off (8 programmable zones)

IP66

14 (850nm)

12VDC/24VAC Dual Voltage

12VDC: 200mA(LEDs off), 310mA (LEDs on)

24VAC: 2W (LEDs off), 3W (LEDs on)

7” x2 3 /

4

14°~122° F (-10°~50° C)

” x3 1 /

2

” (180x70x90 mm) (with sunshield)

18-oz (500g)

Parts List:

1 x Camera with bracket

1 x Mounting plate

1 x Sunshield

4 x Mounting screws

4 x Hex screws

1 x Hex wrench

1 x DC plug with

terminal block

1 x Service monitor

port connector

2 3 /

4

” (70mm) 7” (180mm)

4 23 /

32

” (120mm)

3 1 /

2

”

(90mm)

2 19 /

32

”

(66mm)

ENFORCER

®

3 15 /

16

” (100mm)

2 SECO-LARM U.S.A., Inc.

Overview:

A. Camera

B. Adjustable sunshield

C. Mounting plate

D. Camera base

E. Hex screws

F. Mounting screws

G. Focus

H. Zoom

I. Service cover

J. Female BNC

B connector

(video out)

K. DC jack

L. DC plug with

A terminal block

M. Service monitor port,

OSD joystick

F

D

Before Starting:

1. Please read this manual carefully and keep it for future reference.

2. Use the camera within given temperature and electrical limits.

3. Do not aim the LEDs directly at the eyes when the

LEDs are on.

4. Do not point the camera at the sun. Heat could damage the camera, even when not in use.

5. Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.

1

G

H

I, M

E

C

K

J

NVD Bullet Cameras

Connect service monitor port connector to service monitor port

OSD joystick

Important:

Do not cut DC jack (K) or female BNC connector (J) as warranty will be voided.

L

6. Do not open or disassemble the camera. There are no field-serviceable parts inside.

7. Do not drop the camera or subject it to strong vibrations.

1 Note: Many video monitors produce strong

electromagnetic fields close to the display CRT,

especially when the monitor is turned on or

during de-Gaussing, which occurs automatically

with many monitors when turning on.

Installation:

1. Run a 12VDC or 24VAC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted.

2

2. Temporarily connect the camera to the power supply. Do not cut DC jack or female BNC connector as warranty will be voided. If needed, use the included SECO-LARM DC plug with

terminal block.

3. Remove service cover and connect included service monitor port connector to service monitor port.

4. Connect the service monitor port connector’s BNC to a test monitor.

5. While watching the monitor, hold the camera against the wall or ceiling by hand where it is to be mounted, then turn the camera until it is certain that this mounting location is correct. Use a pencil to mark the location of the four screw holes in the mounting plate.

6. Mount the mounting plate to the wall or ceiling using the four included mounting screws. If the wall is made of drywall, brick, or similar material,

it may be necessary to use screw anchors

(not included).

7. Mount the camera base to the mounting plate using the four included hex screws.

8. Adjust the camera angle.

9. Adjust zoom and focus. Then use the OSD control joystick to adjust camera settings. (See OSD manual).

10. Disconnect the power supply and service monitor connector.

11. Put the sunshield on the camera.

12. Do a final test of the video camera and monitor.

2 Note: The base also allows for surface running of the wires. However, for a cleaner, more secure installation, run the wires through the wall.

SECO-LARM U.S.A., Inc. 3 3 SECO-LARM U.S.A., Inc. 33 3

NVD Bullet Cameras

Troubleshooting

The screen is blank.

The screen image is dim.

The screen image has poor contrast.

The screen image flickers.

The screen image is distorted.

Check that the camera is powered up.

Check that the power supply’s polarity is correct.

Check that the monitor is powered up.

Check that the video cable connecting the camera to the monitor is connected properly.

Clean the lens using a soft, clean cloth.

Check that the light source is adequate.

Adjust the monitor’s contrast knob.

Change the position of the camera.

Change the position of the camera.

Change the position of the camera.

The camera case is hot. Check that the correct power supply is in use.

IR LEDs do not turn on. Check that the correct power supply is in use.

IMPORTANT

Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

WARNING

Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open the case of this device, as there are no field-serviceable components inside.

FCC COMPLIANCE STATEMENT

Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of three (3) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship.

The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at

SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE

The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

4

®

U.S.A., Inc

.

16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com

Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: [email protected]

PIKHR1

MiEV-1626NxGQ_1105.docx

Made in Korea

SECO-LARM U.S.A., Inc.