Craftsman 315.269221 Operator`s manual

Operator's Manual
F E S S I 0
NAL
PROFESSIONAL
CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model Nos.
315.269221
(3/8 in., 9.6 Volt)
315.269261
(1/2 in., 12 Volt)
315.269271
(1/2 in., 14.4 Volt)
MODELS 315.269221
Save this manual
future reference
_,
for
• Safety
• Features
• Assembly
• Operation
• Maintenance
• Parts List
MODELS 315.269261 / 315.269271
CAUTION:
Read and
follow all Safety Rules and
Operating Instructions before
first use of this product.
Customer
Help
Line:
1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman
Visit the Craftsman web page: www.sears.com/craftsman
983000-188
1-03
Estates,
IL 60179
USA
•
•
Warranty..........................................................................................................................................................
2
Introduction
.......................................................................................................................................................
3
•
•
•
•
•
GeneralSafetyRules ........................................................................................................................................
3-4
SpecificSafetyRules.........................................................................................................................................
4-5
Symbols..........................................................................................................................................................
6
ProductSpecifications
.........................................................................................................................................
7
Features..........................................................................................................................................................
7-9
• Assembly.........................................................................................................................................................
10-11
• Operation
.........................................................................................................................................................
12-16
• Maintenance
.....................................................................................................................................................
17
• Accessories.....................................................................................................................................................
17
•
•
Exploded
ViewAndRepairPartsList.....................................................................................................................
18-19
PartsOrdering/ Service ...............................................................................................................................................
20
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
PROFESSIONAL
CORDLESS DRILL-DRIVER
If this rRnFTSMRN Professional Cordless Drill-Driver fails due to a defect in material or workmanship within one year
from the date of purchase, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO THE NEAREST SEARS STORE OR
SEARS SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179
,_
Look for this symbol to point out important
involved.
safety precautions.
It means attention)((
Your safety is
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears
Retail Stores. Always wear eye protection which is marked to comply with ANSI Z87.1.
r
SAFETY AND INTERNATIONAL
SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance, and repair information.
MEANING
Do not expose to rain or use in damp locations.
2
Yourdrill-driverhasmanyfeaturesformakingyourdrilling
operations
morepleasantandenjoyable.Safety,
performance
anddependability
havebeengiventop
priorityin thedesignofthisdrill-drivermakingiteasyto
maintainandoperate.
_1_ CAUTION:Carefullyreadthroughthisentireowner's
manualbeforeusingyournewdrill-driver.Payclose
attentiontotheSpecificSafetyRules/ Symbols,
_
Personal Safety
Warnings and Cautions. If you use your drill-driver
properly and only for it's intended use, you will enjoy
years of safe, reliable service.
WARNING: Read and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
SAVE THESE
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
INSTRUCTIONS
Work Area
•
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
•
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
•
•
•
Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached
to a rotating part of the tool may result in personal
injury.
•
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables
better control of the tool in unexpected situations. Do
not use on a ladder or unstable support.
•
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Safety
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery. Use battery
only with charger listed.
MODEL
BATTERY PACK CHARGER
315.269221
Item No. 9 11030 Item No. 9 11040
(981400-001)
(981399-001 )
315.269261
Item No. 9 11031 Item No. 9 11040
(981401-001)
(981399-001 )
315.269271
•
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery
pack. Carrying tools with your finger on the switch or
inserting the battery pack into a tool with the switch on,
invites accidents.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you
to lose control.
Electrical
•
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
Item No. 9 11033
(981403-001)
Item No. 9 11040
(981399-001 )
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack
listed.
3
Tool Use and Care
•
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
•
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp
cutting edges are less likely to bind and are easier to
control.
•
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is
dangerous and must be repaired.
•
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation, if damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
•
Use only accessories that are recommended by
the manufacturer
for your model. Accessories that
may be suitable for one tool, may create a risk of injury
when used on another tool.
•
•
•
•
Disconnect battery pack from tool or place the switch
in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such
Service
preventivesafety measures reduce risk of starting the tool
accidentally.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
•
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
•
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden
wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
Additional
fire or heat. This will reduce the risk of explosion and
possible injury.
Rules For Safe Operation
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
•
,_
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 16 is
recommended for an extension cord 100 feet or less
in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
Important
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
For best results, your battery tool should be
charged in a location where the temperature is
more than 50°F but less than 100°F. Do not store
outside or in vehicles.
Rules for Battery Tools
•
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing accessories. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not place battery tools or their batteries
WARNING:
Batteries vent hydrogen gas and can
explode in the presence of a source of ignition, such
as a pilot light. To reduce the risk of serious personal
injury, never use any cordless product in the presence of open flame. An exploded battery can propel
debris and chemicals. If exposed, flush with water
immediately.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
near
4
,_llb WARNING:
Never use a battery that has been
dropped or received a sharp blow. A damaged battery
is subject to explosion. Properly dispose of a dropped
battery immediately. Failure to heed this warning can
result in serious personal injury.
Save these instructions. This manual contains
•
Do not operate charger with a damaged cord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
important safety and operating instructions for
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
_,
CAUTION: To reduce risk of injury, charge only
nickel-cadmium and nickel metal hydride type
rechargeable batteries. Other types of batteries
may burst causing personal injury and damage.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
•
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
•
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
To reduce the risk of electric shock, unplug
charger from outlet before attempting any maintenance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
A
To reduce risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting charger. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce
the risk of serious personal injury.
_
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
b. That extension cord is properly wired and in
good electrical condition; and
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
c. That wire size is large enough for AC ampere
rating of charger as specified below:
50'
100'
Cord Size (AWG)
16
16
16
WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemicallytreated lumber.
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
Cord Length (Feet) 25'
DANGER: RISK OF ELECTRIC SHOCK. DO NOT
TOUCH UNINSULATED PORTION OF OUTPUT
CONNECTOR OR UNINSULATED BATTERY
TERMINAL.
Note: AWG = American Wire Gage
SAVE THESEINSTRUCTIONS
5
--
m
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
Volts
Voltage
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
min
Minutes
Time
'_
Alternating Current
Type or a characteristic of current
Direct Current
Type or a characteristic of current
no
No Load Speed
Rotational speed, at no load
.../min
Revolutions or Reciprocation
V
A
L
Per Minute
Safety Alert Symbol
Revolutions, strokes,
surface speed, orbits etc. per minute
Indicates danger, warning or caution.
It means attention!!! Your safety is
involved.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations with them, deserve your careful attention and understanding. The safety warnings do
not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for
proper accident prevention measures.
SYMBOL
MEANING
SAFETY ALERT SYMBOL:
Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
,_
DANGER:
to obey
a safety warning
result
injuryshock
to yourself
or to others.
Always
followFailure
the safety
precautions
to reducewillthe
risk in
of serious
fire, electric
and personal
injury.
WARNING:
to obey
a safety to
warning
serious
injury
to yourself
or to others.
Always
follow Failure
the safety
precautions
reduce can
the result
risk of infire,
electric
shock
and personal
injury.
CAUTION:
obey afollow
safetythe
warning
result intoproperty
or fire,
personal
injury
to
yourself or to Failure
others. toAlways
safety may
precautions
reduce damage
the risk of
electric
shock
and personal injury.
NOTE:
Advises you of information or instructions vital to the operation or maintenance of the equipment.
6
PRODUCT
DRILL-DRIVER
SPECIFICATIONS:
315.269221
315.269261
315.269271
Chuck
3/8 in. Keyless
1/2 in. Keyless
1/2 in. Keyless
Motor
DC Motor 9.6 Volt
DC Motor 12 Volt
DC Motor 14.4 Volt
Gear Train
Two Speed
Two Speed
Two Speed
Switch
Variable Speed
Variable Speed
Variable Speed
No Load Speed
0-300 RPM (Low)
0-300 RPM (Low)
0-350 RPM (Low)
0-1200 RPM (High)
0-1200 RPM (High)
0-1400 RPM (High)
Clutch
24 Positions
24 Positions
24 Positions
Maximum Torque
250 in.lbs
360 in.lbs
410 in.lbs
Item No. 9 11040
Item No. 9 11040
Item No. 9 11040
(981399-001
(981399-001
(981399-001
CHARGER
)
120 V, 60 Hz, AC only
120 V, 60 Hz, AC only
120 V, 60 Hz, AC only
Charging Voltage
9.6 - 24 Volt
9.6 - 24 Volt
9.6 - 24 Volt
Charge Rate
1 Hour
1 Hour
1 Hour
Item No. 9 11030
Item No. 9 11031
Item No. 9 11033
(981400-001)
(981401-001
(981403-001
KNOW YOUR
PACK
DRILL-DRIVER
See Figure 1.
Before attempting to use your drill-driver, familiarize
yourself with all operating features and safety
requirements.
_h,
)
Input
BATTERY
,_
)
WARNING: Carefully read through this entire
operator's manual before using your new drill-driver.
Pay close attention to the Rules For Safe Operation,
Warnings and Cautions. If you use your drill-driver
properly and only for what it is intended, you will enjoy
years of safe, reliable service.
WARNING: Do not allow familiarity with your drilldriver to make you careless. Remember that a careless fraction of a second is sufficient to inflictsevere
injury.
KEYLESS
CHUCK
Your drill-driver has a keyless chuck that allows you to hand
tighten or release drill bit in the chuck jaws.
SWITCH
To turn your drill-driver ON, depress the switch trigger.
Release switch trigger to turn your drill-driver OFF.
)
SWITCH
)
LOCK
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use.
VARIABLE
SPEED
This tool has a variable speed switch that delivers higher
speed with increased trigger pressure. Speed is controlled
by the amount of switch trigger depression.
TWO SPEED
GEAR
TRAIN
Your drill-driver has a two speed gear train designed for
drilling or driving at HI or LO speeds. A slide switch is
located on top of your drill to select either HI or LO speed.
FORWARD/REVERSE
(DIRECTION
SELECTOR
OF ROTATION SELECTOR)
Your drill-driver has a forward/reverse
selector located
above the switch trigger.
WRIST
STRAP
A wrist strap is provided to reduce the chances of dropping
your drill-driver. Place one hand through the wrist strap
when carrying tool.
WARNING:
If any parts are missing, do not operate
your drill-driver until the missing parts are replaced.
Failure to do so could result in possible serious
personal injury.
TWOSPEED
GEAR
TRAIN
(HI-LO)
TORQUE
_
"
MODELNO.315.269221
(3/8 in. KeylessChuck, 9.6 Volt)
ADJUSTMENT
RING
CHARGER
YELLOWLIGHT"ON" ANDRED
LIGHTFLASHINGINDICATES
DEFECTIVEBATTERYPACK
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
KEYLESS
CHUCK
TRIGGER
RED LIGHT"ON" INDICATES
FASTCHARGINGMODE
GREENLIGHT"ON" INDICATESFULLY
CHARGEDANDSLOW CHARGING
TO MAINTAINBATTERYPACK
BATTERY
PACK
>' SCREWDRIVERBITS
Fig. 1
WRISTSTRAP
8
MODEL NO. 315.269261 (1/2 in. Keyless Chuck, 12 Volt)
MODEL NO. 315.269271 (1/2 in. Keyless Chuck, 14.4 Volt)
TORQUE
ADJUSTMENTRING
) SPEED
GEARTRAIN(HI-LO)
KEYLESS
CHUCK
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
SWITCH
TRIGGER
BATTERYPACK
" WRISTSTRAP
Fig. 2
CHARGER
_ee Figure
Your charger has a "key hole" hanging feature for convenient, space saving storage. Screws should be installed so that
center distances are 4-1/8 inches apart.
4-1/8 in.
CHARGER
BATTERYPACKSHOWN
IN CHARGER
BACKSIDE OF CHARGER
Fig. 3
9
AUTO-SPINDLE
LOCK
_ILWARNING:
Make sure to insert drill bit straight into
chuck jaws. Do not insert drill bit into chuck jaws at
an angle and then tighten, as shown in Figure 5. This
could cause drill bit to be thrown from drill, resulting in
possible serious personal injury or damage to the
chuck.
Your cordless drill has an auto-spindle lock. This feature
makes installing and removing bits much easier. When the
switch trigger is released and the motor comes to a
complete stop, you may hear a click. The click you hear
indicates the auto-spindle lock has engaged and locked
the spindle. With the spindle locked, you can easily install
or remove bits by turning the chuck sleeve with one hand.
The auto-spindle lock disengages when the motor starts
again.
UNLOCK
DRILLBIT
CHUCKJAWS
WRONG
Fig. 5
LOCK
REMOVING
BITS
See Figure 3.
RIGHT
INSTALLING
Fig. 4
BITS
See Figure 4.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure ;'1.
•
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Also, raise the front of your drill slightly to keep the bit
from falling out of the chuck jaws.
•
Insert drill bit straight into chuck the full length of the
jaws as shown in Figure 4.
•
Tighten the chuck jaws on drill bit. To tighten, grasp
and hold the drill with one hand, while rotating the
chuck sleeve with your other hand.
Note: Rotate the chuck sleeve in the direction of the
arrow marked LOCK to tighten chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws.
10
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 11.
•
Loosen the chuck jaws from drill bit.
•
To loosen, grasp and hold the drill with one hand,
while rotating chuck sleeve with your other hand.
Note: Rotate chuck sleeve in the direction of the arrow
marked UNLOCK to loosen the chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws.
•
Remove drill bit from chuck jaws.
TO ATTACH
BATTERY
TO REMOVE
PACK TO DRILL
BATTERY
PACK
FROM DRILL
Gee Figure 6.
Gee FigureZ
Note: Battery pack is shipped in a low charge condition.
Therefore, it must be charged prior to use. Refer to page 12,
"CHARGING BATTERY PACK" for charging instructions.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. Gee Figure if.
•
Depress latch located on front of battery pack (1) to
release battery pack.
•
Pull forward on battery pack (2) to remove from drill.
•
•
•
Lock the switch trigger by placing the direction of
rotation selector in center position. Gee Figure ff.
Align raised ribs on battery pack with grooves on
bottom of drill, then attach battery pack to drill as
shown in Figure 6.
Make sure latch on battery pack snaps into place and
battery pack is secured to drill before beginning
operation.
DEPRESSLATCHTO
RELEASEBATTERYPACK
RAISEDRIBS
LATCH
PULL
FORWARD
TO REMOVE
GROOVES
BATTERYPACK
BATTERYPACK
Fig. 6
_,
CAUTION: When attaching battery
drill, be sure raised ribs and grooves
and latch snaps into place properly.
assembly can cause damage to drill
pack.
pack to your
align properly
Improper
and battery
11
Fig. 7
&
If after one hour red light is still flashing, this indicates a
defective battery pack and should be replaced.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
CHARGING
BATTERY
Green light on indicates battery pack is fully charged
and slow charging to maintain battery pack.
Yellow light on and red light flashing indicates defective
battery pack. Return battery pack to your nearest Sears
Repair Center for checking or replacing.
PACK
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until light on front of charger changes
from red to green.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged.
TO CHARGE
•
Charge battery pack only with the charger provided.
•
Make sure power supply is normal house voltage,
120 volts, 60 Hz, AC only.
•
Connect charger to power supply.
•
Attach battery pack to charger by aligning raised ribs
on battery pack with grooves in charger, then slide
battery back onto charger. See Figure 8
•
When your battery pack becomes fully charged, the red light
will turn OFF and the green light will turn ON.
•
After normal usage, 1 hour of charging time is required to be
fully charged. A minimum charge time of 1-1/2 hours is
required to recharge a completely discharged tool.
•
The battery pack will become slightly warm to the touch while
charging. This is normal and does not indicatea problem.
•
Do net place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
•
When the batteries become fully charged, unplug your
charger from power supply and remove the battery
pack.
LED FUNCTION
LED WILL BE LIGHTED TO INDICATE STATUS OF
CHARGER AND BATTERY PACK:
BATTERY
TO
REMOVE
CHARGER
•
Red LED Lighted = Fast Charging Mode.
•
Green LED Lighted = Fully Charged And Slow
Charging To Maintain Battery Pack.
•
Red LED Flashing = Hot Or Deeply Discharged
Battery Pack. Also Defective Battery Pack After 1
Hour.
•
Yellow LED Lighted and Red LED Flashing =
Defective Battery Pack.
IMPORTANT
TO
ATTACH
INFORMATION
FOR
RECHARGING
HOT BATTERIES
Under extreme continuous use, the batteries in your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 1 hour before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the red light on your
battery charger to flash. When battery pack cools down,
red light will glow continuously indicating fast charging
mode, 1 hour charge time. Once the battery pack cools
down, it will recharge battery pack in fast charging mode
as normal.
GROOVES
Fig. 8
•
OF CHARGER
Red light should turn on. Red light indicates fast
charging mode.
Note: This situation only occurs when extreme continuous
use of your drill causes the batteries to become hot. It
does not occur under normal circumstances. Refer to
If red light is flashing, this indicates battery pack is
deeply discharged or hot.
If battery pack is hot, red light should become steady
after battery pack has cooled down.
"CHARGING BATTERY PACK" for normal recharging of
batteries. If the charger does not charge your battery pack
under normal circumstances, return both the battery pack
and charger to your nearest Sears repair center for
electrical check.
If battery pack is deeply discharged, red light should
become steady after voltage has increased, normally
within 60 minutes.
12
SWITCH
SWITCH
LOCK
See Figure
See Figure 11.
To turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
The switch trigger can be locked in the OFF position. This
feature can be used to prevent the possibility of accidental
starting when not in use. To lock switch trigger, place the
direction of rotation selector in center position.
SELECTORWITH
REVERSE
CENTERLOCKPOSITION
TRIGGER
VARIABLE
Fig. 9
SPEED
FORWARD
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression.
_lb
Note: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal
part of the switch function.
REVERSIBLE
TWO SPEED
See Figure I I.
GEAR TRAIN
See Figure 10.
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be
positioned to the left of the switch for drilling. The drilling
direction is reversed when the selector is to the right of
the switch. When the selector is in center position, the
switch trigger is locked.
Your drill has a two-speed gear train designed for drilling
or driving at LO (1) or HI (2) speeds. A slide switch is
located on top of your drill to select either LO (1) or HI (2)
speed. When using drill in the LO (1) speed range, speed
will decrease and unit will have more power and torque.
When using drill in the HI (2) speed range, speed will
increase and unit will have less power and torque. Use
LO (1) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.
TWO SPEED
GEARTRAIN(HI-LO)
Fig. 11
,_1t CAUTION: To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direction of rotation or the two speed gear train
(hi-lo).
LO
SPEED
To stop, release switch trigger and allow the chuck to
come to a complete stop.
HI
SPEED
Fig. 10
13
KEYLESS
ADJUSTABLE
CHUCK
See Figure 12
TORQUE
CLUTCH
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and
the size of screw you are using.
A keyless chuck has been provided with your drill to allow
for easy installation and removal of bits. As the name
implies, you can hand tighten or release drill bits in the
chuck jaws. Arrows on the chuck indicate which direction
to rotate the chuck sleeve in order to LOCK (tighten) or
UNLOCK (release) the chuck jaws. Loosen the chuck
sleeve by rotating it counterclockwise with one hand.
Insert drill bit straight into the chuck the full length of the
jaws, and tighten securely by rotating the chuck sleeve in
clockwise direction.
TO ADJUST
UNLOCK
(Release)
TORQUE
•
Identify the twenty four torque indicator settings
located on the front of your drill. See Figure 13.
•
Rotate adjusting ring to the desired setting.
1 - 4
For driving small screws.
5 - 8
For driving screws into soft
material.
9 - 12
For driving screws into soft and
hard materials.
DRILLBIT
• 13 - 16
For driving screws in hard wood.
• 17 - 20
For driving large screws.
• 21 -,11
For heavy drilling.
Note: Remember the two-speed feature (HI-LO) when
setting torque. The amount of torque will vary depending
on which speed setting you have your drill-driver. Switching to LO speed will increase torque. Switching to HI
speed will decrease torque.
CHUCKJAWS
ADJUSTINGRING
LOCK
(Tighten)
TO DECREASE
TORQUE
CHUCKSLEEVE
Fig. 12
_lh, WARNING:
Do not hold chuck sleeve with one hand
and use power of the drill to tighten chuck jaws on
drill bit. Chuck sleeve could slip in your hand or your
hand could slip and come in contact with rotating drill
bit. This could cause an accident resulting in serious
personal injury.
TO INCREASE
TORQUE
Fig. 13
14
When drilling hard smooth surfaces use a center punch to
mark desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However,
the low speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate
your drill at a low speed until the hole is started.
The material to be drilled should be secured in a vise or
,t_tb WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
APPLICATIONS
(Use drill-driver only for the purpose listed below)
•
Drilling in wood.
•
Drilling in ceramics, plastics, fiberglass, and laminates.
•
•
Drilling in both hard and soft metals.
Using driving accessories, such as driving screws with
screwdriver bits.
•
Mixing paints.
with clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
_,
DRILLING
Gee Figure14.
WARNING:
Be prepared for binding or bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
i
c
I
I
I
Fig. 14
15
CHUCK
Insert hex key in chuck and tighten chuck jaws
securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It
can now be unscrewed by hand. See Figure 17.
REMOVAL
Gee Figures15,16,and 17.
The chuck must be removed in order to use some
accessories. To remove:
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 1/.
•
Insert a 5/16 inch or larger hex key into the chuck of
your drill and tighten the chuck jaws securely.
•
Tap the hex key sharply with a mallet in a clockwise
direction. See Figure 15. This will loosen the screw in
the chuck for easy removal.
MALLET
CHUCKJAWS
Fig. 17
TO RETIGHTEN
HEX KEY
CHUCK
The chuck may become loose on spindle and develop a
wobble. Periodically check chuck screw for tightness.
KEYLESS
CHUCK
To tighten, follow these steps:
Fig. 15
•
A LOOSE
Open chuck jaws and remove hex key. Remove the
chuck screw by turning it in a clockwise direction. See
FigureIG.
•
Lock the switch trigger by placing the direction of
rotation selector in center position, geeFigure 11.
•
Open the chuck jaws.
•
Insert hex key into chuck and tighten chuck jaws
securely. Tap hex key h sharply with a mallet in a
clockwise direction. This will tighten chuck on the
spindle.
•
Open the chuck jaws and remove hex key.
•
Tighten the chuck screw.
Note: The chuck screw has left hand threads.
Note: The screw has left hand threads.
SCREWDRIVER
Fig. 16
16
_tb
Do net abuse power tools. Abusive practices can
WARNING:
When servicing use only identical
Craftsman replacement parts. Use of any other
parts may create a hazard or cause product damage.
damage tool as well as workpiece.
Only the parts shown on parts list, page 17, are intended
to be repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc.
_l_
,_
WARNING:
Do not attempt to modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
•
Store and charge your batteries in a cool area.
Temperatures above normal room temperature will
shorten battery life.
•
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
BATTERIES
The battery pack for your drill-driver is equipped with
nickel-cadmium rechargeable batteries. Length of service
from each charging will depend on the type of work you
are doing.
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do net disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry,
could result in a serious burn.
All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
To obtain the longest possible battery life, we suggest the
following:
To preserve natural resources, please
recycle or dispose of batteries properly.
BATTERY PACK
FOR RECYCLING
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium
batteries in ordinary trash.
A
Consult your local waste authority for information
regarding available recycling and/or disposal options.
The following
Purchase
recommended
these accessories
accessories
are currently
REMOVAL
AND PREPARATION
WARNING:
Upon removal, cover the battery pack's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
available
at Sears Retail Stores.
if your drill is Model No. 315.269221
•
6-Pc. Extra Length Magnite Power Bit Set
•
17-Pc. Power Screwdriver/Nutdriver
•
30-Pc. Power Screwdriver/Nutdriver
•
High Speed Bits (For Wood or Metal)......3/4
Purchase
these accessories
Set and Case
if your drill is Model
No. 315.269261
or 315.269271
•
6-Pc. Extra Length Magnite Power Bit Set
•
High Speed Bits......1/2 in. Max.
•
30-Pc. Power Screwdriver/Nutdriver
Set and Case
•
Wood Boring Bits......1-1/2 in. Max.
•
17-Pc. Power Screwdriver/Nutdriver
Set and Case
,_
WARNING:
The use of attachments
or accessories
not listed
17
might be hazardous.
Set and Case
in. Max.
--
CRAFTSMAN
3/8 in. PROFESSIONAL
CORDLESS
MODEL NO, 315.269221
DRILL-DRIVER
--
in all correspondence regarding your CRAFTSMAN 318 in. PROFESSIONAL CORDLESS DRILL-DRIVER
The
model
number repair
will beparts.
found on a plate attached to the motor housing. Always mention the model number
or when
ordering
SEE BACK
PAGE FOR PARTS
ORDERING
INSTRUCTIONS
5
PARTS
Key
No.
LIST
Part
Number
Description
1
616478-003
Screw (Special) ................................................................................
t
2
981502-001
Chuck (ttern No..9- 20955) ................................................................
t
3
981501-001
Quan.
Logo Plate ........................................................................................
t
4
* Item No. _911030
Battery Pack (961400-001) ..............................................................
t
5
* Item No. 9 11040
Charger (961399-001 ) ......................................................................
t
3073064
Carrying Case - Not Shown .............................................................
t
983000-188
Operator's Manual
6
* Can Be Purchased Thru RSOS (Retail Special Order System)
18
1
--
CRAFTSMAN
1/2 in. PROFESSIONAL
CORDLESS
DRILL-DRIVER
MODEL NOS. 315.269261 / 315,269271
--
The model number will be found on a plate attached to the motor housing. Always mention the model number
in all correspondence regarding your CRAFTSMAN
or when ordering repair parts.
SEE BACK
PAGE
1/2 in. PROFESSIONAL
FOR PARTS
ORDERING
CORDLESS DRILL-DRIVER
INSTRUCTIONS
2
1
3
5
4
PARTS
Key
No.
LIST
Part
Number
Description
1
975379-000
Screw (Special) ................................................................................
t
2
981503-001
Chuck (item No..9. 20956) ................................................................
t
981501-001
Logo Plate ........................................................................................
t
3
4
5
6
Quan.
* Item No. 9 11031
Battery Pack (981401-001 ) (Model No. 315.269261 ) ...................... t
• Item No. 9 11033
Battery Pack (981403-001)
* Item No. _911040
Charger (981399-001 ) ......................................................................
3051718
3051719
Carrying CaseCarrying Case-
983000-188
Operator's Manual
(Model No. 315.269271 ) ...................... t
Not Shown (Model No. 315.269261)
Not Shown (Model No. 315.269271)
* Can Be Purchased Thru RSOS (Retail Special Order System)
19
t
.................... t
.................... t
|
Get it fixed, at your home or ours!
Your Home
For repair-in
your home-of
all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime,
day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced
1-800-827-6655
(U.S.A.)
1-800-361-6665
Para pedir servic=o de reparacion
a domicdio, y para ordenar piezas:
1-888-SU-HOGAR
_, Marca
rT
• c Marque
Reg_strada
/
IH
de commerce
(Canada
Au Canada pour service
en fran(;a=s:
1-800-LE-FOYER
sM
Mc
(1-800-533-6937)
www.sears
ca
(1-888-784-6427)
_, Registered Trademark /
by Sears:
"_Trademark / _F
"'_Serv=ce Mark of Sears Roebuck and Co
TF
Marca
ID
/_
de Fabnca
Marque
! sTI Marca de Servlclo
deposee
de Sears
Roebuck
de Sears,
and Co
Roebuck
and Co
_, Sears,
Roebuck
and Co