Craftsman 139.53225SRT1 Owner`s manual

OWNER’S
MANUAL
Model No.
139.53525SRT
139.53627SRT
139.53636SRT
139.53640SRT
139.53641SRT
For Residential Use
Only
Caution:
Read and follow all
safety rules and
operating instructions
before first use of this
product.
®
1/2 HP
GARAGE DOOR OPENER
■
■
■
■
■
■
■
Fasten the manual
near the garage door
after installation.
Complies with UL 325
regulations effective
January 1, 1993
■
Safety Precautions
Assembly
Installation
Adjustment
Care and Maintenance
Operation
Troubleshooting
Parts List
®
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Contents
Page
A review of safety alert symbols.................................2
You'll need tools..........................................................3
Safety information regarding garage door locks
and ropes ..................................................................3
Testing your garage door for sticking, binding
and balance...............................................................3
Illustration of sectional door installation .....................4
Illustration of one-piece door installation ...................5
Carton inventory..........................................................6
Hardware inventory.....................................................7
Assembly section - pages 8 – 11
Assemble T-rail .........................................................8
Attach cable pulley bracket.......................................8
Install trolley ..............................................................9
Fasten T-rail to opener .............................................9
Install chain/cable ...................................................10
Attach sprocket cover .............................................10
Tighten the chain and cable ...................................11
Installation section - pages 11 – 27
Installation safety instructions.................................11
Determine header bracket location
Sectional door .......................................................12
One-piece door .....................................................13
Install the header bracket .......................................14
Attach the T-rail to header bracket .........................15
Position the opener.................................................16
Hang the opener .....................................................17
Install the wall control .............................................18
Contents
Page
Install the light and lens .................................................19
Attach emergency release rope and handle.................19
Electrical requirememts .................................................20
Safety reversing sensor information..............................21
Install the safety reversing sensor...........................22, 23
Fasten door bracket (sectional door) ............................24
Fasten door bracket (one-piece door)...........................25
Connect door arm to trolley (sectional door).................26
Connect door arm to trolley (one-piece door) ...............27
Adjustment section - pages 28 – 30
Travel limit adjustments.................................................28
Force adjustments .........................................................29
Test the safety reversing sensor ...................................30
Test the safety reverse system ....................................30
Operation safety instructions...........................................31
Care of your opener.........................................................31
Maintenance schedule ....................................................31
Operation of your opener ................................................32
Receiver and remote control programming ....................33
Having a problem? ....................................................34, 35
Repair parts, rail assembly..............................................36
Repair parts, installation ..................................................36
Repair parts, opener assembly .......................................37
Accessories......................................................................38
Index ................................................................................39
How to order repair parts.................................................40
Maintenance agreement..................................................40
Warranty ..........................................................................40
Start by reviewing these important safety alert symbols
When you see these Safety Symbols on the following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the corresponding instructions. The hazard may
come from something mechanical or from electric shock. Read the instructions carefully.
WARNING
WARNING
WARNING WARNING
WARNING
WARNING
Mechanical
Electrical
When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage
to your garage door and/or the garage door opener if you do not comply with the corresponding
instructions. Read the instructions carefully.
CAUTIONCAUTION
CAUTION
This garage door opener is designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the safety instructions contained in this manual.
2
You'll Need Tools
During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below.
Pencil
Carpenter's
Level
1
2
Hack Saw
Tape Measure
Wire Cutters
Drill
Stepladder
Claw Hammer
3/16", 5/16" and
5/32" Drill Bits
1/2" and 7/16" Sockets
and Wrench
Pliers
Screwdriver
WARNING
Adjustable End Wrench
CAUTION
To avoid damage to the garage door and
opener, disable locks before installing and
operating the opener. Use a wood screw or nail
to hold locks in the "open" (unlocked)
position.
Operation at other than 120V 60 Hz will cause
opener malfunction and damage.
An unbalanced garage door might not reverse
when required and someone under the door
could be seriously injured or killed.
If your garage door binds, sticks or is out of
balance, call for professional garage door
service. Garage doors, door springs, cables,
pulleys, brackets and their hardware are under
extreme tension and can cause serious injury
or death. Do not try to loosen, move or adjust
them yourself!
Ropes left on a garage door could cause
someone to become entangled and killed.
Remove all ropes connected to the door before
installing and operating the opener.
Before you begin, complete the following test to
make sure your door is balanced, and is not
sticking or binding:
• Lift the door about halfway as shown. Release the
door. It should stay in place, supported entirely by
its springs.
• Raise and lower the door to see if there is any
binding or sticking.
Identify the type and height of your door and any
special conditions that exist and any additional
materials that may be required by referring to the lists
on page 4 or page 5.
SECTIONAL DOOR
ONE-PIECE DOOR
3
SECTIONAL Door Installation
Before you begin, survey your garage area to
see whether any of the conditions below apply
to your installation.
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door
with glass panels, etc.).
See page 24 for details.
FINISHED CEILING
Support bracket &
fastening hardware
is required.
See page 17.
Slack in Chain Tension
is Normal When
Garage Door is Closed
Header Wall
———
Extension
Spring
OR
Torsion
Spring
Door
Center
Access Door
———
——
Safety
Reversing
Sensor
Safety Reversing Sensor
Floor must be level
across width of door.
Header
Bracket
Based on your particular requirements, there are
several installation steps which might call for
materials and/or hardware not included in the carton.
• Step 1, page 12 - Look at the wall or ceiling above
the garage door. The header bracket must be
securely fastened to structural supports.
• Step 5, page 17 - Do you have a finished ceiling in
your garage? If so, a support bracket and
additional fastening hardware may be required.
• Safety reversing sensor, page 21 - Depending
upon garage construction, wood blocks may need
to be fastened to mounting locations before
sensors are installed.
• Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor will require hardware not
provided.
• Step 11, page 24 - Do you have a steel, aluminum,
fiberglass or glass panel door? If so, horizontal
and vertical reinforcement is required.
• Look at the garage door where it meets the floor.
It must close on the floor all the way across.
Otherwise, the safety reverse system may not
work properly. See page 30. Floor or door should
be repaired.
• If your door is more than 7 feet high, see the
longer rails available on page 38.
Cable Pulley
Bracket
Trolley
Cable
Garage
Door
Spring
Closed Position
Rail Assembly
Emergency Release
Rope & Handle
Straight
Door
Arm
Header
Wall
Curved
Door
Arm
Door Bracket
Garage
Door
• The opener can be installed within 2 feet to the left
or right of the door center if there is a torsion spring
or center bearing plate in the way of the header
bracket or door bracket area. If your door has
extension springs, the opener must be installed
in the center of the door. See pages 12 and 24.
• Do you have an access door in addition to the
garage door? If not, Model 53702 Emergency
Key Release is required. See page 38.
You may find it helpful to refer back to this page as
you proceed with the installation of your opener.
4
One-Piece Door without Track
ONE-PIECE Door Installation
Before you begin, survey your garage area to
see whether any of the conditions below apply
to your installation.
Slack in chain tension
is normal when
garage door is closed.
FINISHED CEILING
Support bracket
& fastening
hardware is required.
See page 17.
Header
Wall
Closed Position
Cable
Pulley Bracket
Trolley
Cable
Access Door
Header
Bracket
T-rail
Door Bracket
Straight
Door
Arm
Header
Wall
Safety
Reversing
Gap between floor and bottom Sensor
Safety
of door must not exceed 1/4".
Reversing Sensor
Emergency
Release
Rope & Handle
Curved
Door
Arm
Garage
Door
One-Piece Door with Track
Based on your particular requirements, there are
several installation steps which might call for
materials and/or hardware not included in the carton.
• Step 1, page 13 - Look at the wall or ceiling above
the garage door. The header bracket must be
securely fastened to structural supports.
• Step 5, page 17 - Do you have a finished ceiling in
your garage? If so, a support bracket and
additional fastening hardware (not supplied) may
be required.
• Safety reversing sensor, page 21 - Depending on
garage construction, wood blocks may need to be
securely fastened to mounting locations before
sensors are installed.
• Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor will require hardware that
is not provided.
• Step 11, page 25 - Generally, a one-piece door
does not require reinforcement. If your door is
lightweight, you can refer to the information
relating to sectional doors on page 24.
• Step 11, page 25 - Depending on your door's
construction, you might need additional mounting
hardware for the door bracket.
• Do you have an access door in addition to the
garage door? If not, Model 53702 Emergency Key
Release is required. See page 38.
• The gap between the bottom of the garage
door and the floor cannot exceed 1/4".
Otherwise, the safety reverse system may not
work properly. See page 30. The floor or the door
should be repaired.
Access
Door
Safety
Reversing
Sensor
Safety
Reversing
Sensor
Floor must be level
across width of door
Closed Position
Header
Wall
Cable
Pulley Bracket
Header
Bracket
Garage
Door
Cable
Curved
Door Arm
Door
Bracket
Straight
Door
Arm
Trolley
Chain
T-rail
Emergency Release
Rope & Handle
You may find it helpful to refer back to this page
as you proceed with the installation of your
opener.
5
Opener Carton Inventory
Your garage door opener is packaged in two cartons which contain all parts illustrated below. If anything is
missing, carefully check the packing material. Parts may be "stuck" in the foam. Hardware for assembly and
installation is shown on page 7.
Models 53824 (2), 53637 (2),
53635 (2), 53629 (1), 53628 (2),
53425 (1), 53325 (1)
Three-Function Remote Control
with Visor Clip (1)
Model 53225 only
Models 53637,
53635, & 53425
Model 53635 only
Multi-Function
Keyless Entry
Single-Function Remote Control
with Visor Clip (1)
Lighted Console
Wall Control
Model 53824 only
Models 53225,
53325, 53628, 53629
SEARS /CRAFTSMAN
LOCK
LIGHT
Model 53629 only
Cable
Pulley Bracket
Deluxe Wall Control
Lighted Push Button
Wall Control
and Hardware
Three-Function
Compact Remote Control
2-Conductor
Bell Wire
White & White/Red
T-Rail
Center Section
Trolley
Models 53824, 53637, 53635,
53629, 53628, 53425, 53325
RAGE
TO GA
DOOR
T-Rail
End Sections
Door Bracket
Door Bracket Plate
Sprocket Cover
Light Lens
G
MO
UN
NL
TO
Y
"C" Wrap (2)
ILIN
CE
UP
Header Bracket
Chain and Cable
in Dispensing Carton
Safety Reversing Sensor
Mounting Bracket
With Square Holes (2)
Hanging Brackets
Curved Door
Arm Section
Safety Reversing Sensor
Mounting Bracket
With Slot (2)
Safety Labels
and
Literature
(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with
2-Conductor White & White/Black Bell Wire
attached
6
Straight Door
Arm Section
Separate all hardware from the packages in the rail carton and the opener carton, as
shown below, for the assembly and installation procedures.
Assembly Hardware
Hex Screw
5/16" - 18 x 7/8" (3)
Washered Screw
5/16" - 18 x 1/2" (2)
(mounted in opener)
Nut
5/16" - 18 (5)
Carriage Bolts
1/4" - 20 x 1/2" (4)
Trolley Threaded Shaft (1)
Master Link (2)
Lock Nut
1/4" - 20 x 7/16" (4)
Lock Washer
5/16" (4)
Installation Hardware
ASE
GRE
RAIL . 83A4
O
N
NOTIC
Hex Screw
5/16"- 18 x 7/8" (4)
E
Rail Grease
Handle
Lag Screw
5/16"-18 x 1-7/8" (4)
Nut 5/16" - 18 (6)
Lock Washer 5/16" (6)
Rope
Screw
6AB x 1" (2)
Carriage Bolt
5/16"-18 x 2-1/2" (2)
Clevis Pin
5/16" x 2-3/4" (1)
Insulated
Staples (10)
Dry Wall Anchors (2)
Clevis Pin
5/16" x 1" (2)
Ring
Fastener (3)
Safety Reversing Sensor
Installation Hardware
Lag Screw
1/4 x 1-1/2" (4)
Hex Screw
1/4-20 x 1-1/2" (2)
Carriage Bolts
1/4" - 20 x 1/2" (4)
Lock Nut
1/4" - 20 (4)
Wing Nut (2)
Screw
#10 - 32 x 3/8" (4)
Lock Nut
#10 x 32 (4)
Insulated
Staples (20)
7
Assembly Section: Pages 8 – 11
To avoid installation difficulties, do not run the garage door opener until instructed to do so.
Make sure bolt necks are
seated in the square
holes and rails are
aligned before you
tighten lock nuts. (See
right and wrong views).
Improper assembly can
cause jerky trolley
operation, noise and/or
nuisance door reversals.
Assembly Step 1
Assemble the T-rail & Attach
the Cable Pulley Bracket
• Align the 3 T-rail sections on a flat surface exactly
as shown. The end sections are identical. Make
A is
sure the "arrow label" on the center section
Be
st
u
pointing toward the door.
M
ail
T-r
• Insert the carriage bolts so the square
bolt necks
&
t
ke
seat in the square holes in Bthe
rac T-rail end sections
il
Ra
and pass through the round
holes in T-rail center
section. Assemble lock nuts, ensure alignment and
Lock Washer
Nut
tighten. 5/16"
Right
Wrong
T-RAIL BACK
(TO OPENER)
1/4'' Lock Nut
T-rail
(End Section)
5/16"
Brace
T-rail
(Center Section)
If T-rail is not assembled
EXACTLY as shown, trolley
will not travel smoothly
along length of rail or it will
hit against the nuts.
Carriage Bolt
1/4"-20x1/2"
TO
GA
RAG
ED
OO
R
Brace
T-rail
(End Section)
Hardware Shown Actual Size
Cable pulley bracket
attaches to FRONT
END of T-rail
Square Carriage
Bolt Holes
Carriage Bolts
1/4" - 20 x 1/2"
Lock Nut
1/4" - 20 x 7/16"
T-RAIL FRONT
(TO DOOR)
Hex Screw
5/16" - 18 x 7/8"
• Position the cable pulley bracket on the front end of the
T-rail as shown. Fasten securely with the hardware.
Nut
5/16" - 18
Lock Washer
5/16"
Hex Screws
5/16"-18x7/8"
Cable Pulley
Bracket
ed
ign
e
tB
Al
s
ail
t&
Mu
ke
ac
r
il B
T-r
Ra
Lock Washer
5/16"
Right
Nut
5/16"
8
Wrong
When tightening
the screws, be
sure to keep
bracket parallel
to the rail.
Otherwise, the
rail may bow
when opener is
operated.
Hardware Shown
Actual Size
Assembly Step 2
Install the Trolley on the T-rail
• Attach the threaded shaft to the trolley with the
lock washer and nuts as shown.
Lock Washer
5/16"
Nut
5/16"-18
Trolley
Lock Washer
5/16"
Outer Nut
5/16"
Trolley
Threaded Shaft
Inner Nut
5/16"
TO
GA
R
AG
E
DO
OR
Trolley
Temporary Stop
Screwdriver
• As a temporary stop, insert a screwdriver into the
hole in the front end of the T-rail.
• Slide the trolley assembly along the rail to the
screwdriver stop.
If trolley hits against any nuts on the T-rail, the
bolts and nuts were attached from the wrong
side and must be repositioned. Review Step 1.
Assembly Step 3
CAUTION
Fasten the T-rail to the Opener
To fasten rail, use only those screws mounted
in the top of the opener. Any other screws will
cause serious damage to the opener.
• Place the opener on packing material to protect
the cover. For convenience, put a support under
the cable pulley bracket.
• Remove the (2) 5/16"-18x1/2" washered screws
mounted in the top of the opener.
• Align the holes in the back section of the T-rail with
the holes in the opener.
• Fasten the rail with the (2) washered screws
previously removed. Tighten securely.
Remember to use only these screws! Any other
screws will cause serious damage to the opener.
• Insert a 5/16"-18x7/8" hex screw into the trolley
stop hole in the T-rail as shown. Tighten securely
with a 5/16" lock washer and nut. This screw limits
trolley travel in the UP direction.
Washered Screw
5/16"-18x1/2"
Hex Screw
5/16"-18x7/8"
Trolley
Stop Hole
T-rail
(Back Section)
Lock Washer
5/16"
Nut
5/16"-18
Hardware Shown Actual Size
Hex Screw
5/16"-18x7/8"
Nut
5/16"
Lock Washer
5/16"
9
Use Only This
Type and Size
Screw
Assembly Step 4
WARNING
Install the Chain/Cable &
Attach the Sprocket Cover
Serious injury can result if fingers become
entangled in moving opener sprocket. Attach
sprocket cover securely. Never operate opener
while your hand is near the opener sprocket.
Dispensing Carton
Figure 2
Leave Chain and Cable
Inside Dispensing
Carton to Prevent Kinking.
Opener
Sprocket
Keep Chain and Cable
Taut When Dispensing
• Detach the cable loop from the carton and fasten it
to the trolley with a master link from the hardware
bag. See master link procedure, Figure 1.
• With the trolley against the screwdriver, dispense
the cable around the pulley.
• Proceed back around the opener sprocket,
Master Link
Figure 2. Be sure sprocket teeth engage the
chain.
Clip-On
Spring
Continue forward to the trolley threaded shaft,
Figure 3.
Master
Link Cap
Master Link
• Use the second master link to connect the
Clip-On Spring
chain to the flat end of the shaft. Check
to make sure the chain is not
Master
Link Cap
twisted.
Cable
Loop
• Remove the screwdriver.
Master Link
Clip-On Spring
Figure 3
Master
Link Master
Cap Link
Clip-On Spring
Flat End
of Trolley
Threaded Shaft Master
Link Cap
Flat End
of Trolley
Threaded Shaft
Chain
T-rail
Cable
Loop
Pin Notch
Trolley
Pin
Master
Link Bar
Trolley
Cable
Pulley
Master
Link Bar
Install Chain and Cable
In This Direction
Cable
Pulley
Figure 1
Master Link Procedure:
Push pins of master link bar
through cable loop and hole in
front end of trolley. Push cap
Sprocket
over pins and into notches.
Slide clip-on spring over cap
and into notches until both
pins are securely locked.
Install Chain and Cable
In This Direction
Sprocket
Cover
Back Tab Slot
Front Tab S
Top of Opener
Front Tab Slot
To attach the sprocket cover:
• Insert the back tab in the opener slot. Squeeze the
cover slightly and insert the front tab in the slot on
the mounting plate.
Mounting
Plate
10
Assembly Step 5
Tighten the Chain & Cable
Outer Nut
• Spin the inner nut and lock washer down the
threaded shaft, away from the trolley.
• To tighten the chain, turn outer nut in the direction
shown. As you turn the nut, keep the chain
from twisting.
• When the chain is approximately 1/2" above the
base of the T-rail at its midpoint, re-tighten the
inner nut to secure the adjustment.
Sprocket noise can result if chain is either too
loose or too tight.
When installation is complete, you may notice some
chain droop with the door closed. This is normal. If
the chain returns to the position shown when the
door is open, do not re-adjust the chain.
Lock
Washer
Inner Nut
To Tighten Outer Nut
To Tighten
Inner Nut
Trolley
Chain
1/2 Inch
NOTE: During future maintenance, ALWAYS
pull the emergency release handle to disconnect
trolley before adjusting chain.
Base of T-rail
You have now finished assembling your garage door opener. Please read the following
warnings before proceeding to the installation section:
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING
WARNING
To reduce the risk of severe injury or death to persons:
1.
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.
2. Install only on a properly balanced and lubricated garage door. An improperly balanced door
may not reverse and could result in severe injury or death. Repairs to cables, spring assemblies
and other hardware must be made by a professional service person before installing opener.
3. Disable all locks and remove all ropes connected to the garage door before installing the opener.
Ropes connected to a garage door can cause entanglement and death.
4. If possible, install door opener 7 feet or more above floor with the emergency release handle
mounted 6 feet above the floor.
5. Do not connect the opener to power source until instructed to do so.
6. Locate the Wall Control within sight of the door at a minimum height of 5 feet where small
children cannot reach and away from all moving parts of the door.
7. Install the User Safety Instruction Label on the wall adjacent to the control button and the
Maintenance Instruction Label in a prominent location on the inside of the garage door.
8. Upon completion of the installation, the door must reverse when it comes in contact with a
one-inch high object or a 2x4 laid flat on the floor.
9. Do not wear watches, rings or loose clothing while installing or servicing an opener. Jewelry or
loose clothing can be caught in the mechanism of the garage door or the opener.
11
Installation Section: Pages 12 – 27
Installation Step 1
WARNING
Determine Header Bracket Location
If the header bracket is not rigidly fastened to
a structural support on the header wall or
ceiling, the safety reverse system may not
work properly (see page 30). The door might
not reverse when required, and could cause
serious injury or death.
The garage door springs, cables, pulleys,
brackets and their hardware are under extreme
tension. Do not attempt to loosen, move or
adjust them yourself. Serious personal injury
or death could result. Call for professional
garage door service.
Installation procedures vary according to
garage door types. Follow the instructions
which apply to your door.
SECTIONAL Door and
ONE-PIECE Door With Track
Header
Wall
Finished
Ceiling
Vertical
Guideline
2x4
Structural
Supports
• Close the door and mark the inside
vertical centerline of the garage door.
• Extend the line onto the header wall
above the door.
Remember, you can fasten the
header bracket within 2 feet of the
left or right of the door center only if
a torsion spring or center bearing
plate is in the way; or you can attach
it to the ceiling (refer to page 14)
when clearance is minimal. (It may
be mounted on the wall upside down
if necessary, to gain approximately
1/2".)
If you need to install the header bracket
on a 2x4 (on wall or ceiling), use lag
screws (not supplied) to securely fasten
the 2x4 to structural supports as shown
here and on page 13.
Vertical
Guideline
Ceiling
• Open your door to the highest
point of travel as shown. Draw
an intersecting horizontal line
on the header wall 2" above
the high point. This height will
provide travel clearance for the
top edge of the door.
Door clearance brackets are
available for sectional doors
when headroom clearance is
less than 2". See accessory
page 38.
Header
Wall
2"
Header
Wall
2"
Track
Track
Highest Point
of Travel
Highest Point
of Travel
Door
Door
Sectional door
with curved track
Proceed to Step 2, page 14.
12
One-piece door
with horizontal track
ONE-PIECE Door Without Track
Read the Safety instructions on page 12. They also apply to doors without tracks.
Unfinished
Ceiling
Header Wall
Vertical
Centerline
• Close the door and mark the
inside vertical centerline of
your garage door. Extend the
line onto the header wall
above door.
If headroom clearance is
minimal, you can install the
header bracket on the ceiling.
See page 14.
• If you need to install the
header bracket on a 2x4 (on
wall or ceiling), use lag screws
(not supplied) to securely
fasten the 2x4 to structural
supports as shown.
2x4
Structural
supports
2x4
Vertical
Centerline of
Garage Door
OPTIONAL CEILING MOUNT
FOR HEADER BRACKET
Header Wall
Header
Wall
Highest Point
of Travel
Highest Point
of Travel
Distance
Door
Jamb
Hardware
Distance
Door
Pivot
One-piece door without track
jamb hardware
One-piece door without track
pivot hardware
• Open your door to the highest point of travel as
shown. Measure the distance from the top of the
door to the floor. Subtract the actual height of the
door. Add 8" to the remainder. (See Example).
• Close the door and draw an intersecting horizontal
line on the header wall at the determined height.
If the total number of inches exceeds the height
available in your garage, use the maximum
height possible, or refer to page 14 for ceiling
installation.
EXAMPLE
Distance from top of door
(at highest point of travel) to floor...........................92"
Actual height of door .............................................-88"
Remainder................................................................4"
Add .........................................................................+8"
Bracket height on header wall ..............................=12"
(Measure UP from top of CLOSED door.)
Proceed to Step 2, page 14.
13
You can attach the header bracket either to the
wall above the garage door, or to the ceiling.
Follow the instructions which will work best for
your particular requirements.
Installation Step 2
Install the Header Bracket
Fasten the Header Bracket to the Wall
• Center the bracket on the vertical guideline with
the bottom edge of the bracket on the horizontal
line as shown (with the arrow pointing toward the
ceiling).
Header
Wall
Y
NL
TO
UN
G
• Mark either set of bracket holes (do not use the
holes designated for ceiling mount). Drill 3/16" pilot
holes and fasten the bracket securely to a structural
support with the hardware provided.
Wall
Mounting Holes
Vertical
Center
Line
Lag Screws
5/16"x18x1-7/8"
MO
ILIN
CE
UP
CEILING MOUNT ONLY
Header
Bracket
UP
2x4
Structural
Support
Door
Spring
The nail hole is for positioning
only. You must use lag screws to
mount the header bracket.
2"
Garage
Door
Highest
Point of Travel
(of Garage Door)
Optional
Wall Mounting
Holes
Hardware Shown Actual Size
Vertical
Center
Line
Lag Screw
5/16"-18x1-7/8"
Fasten the Header Bracket to the Ceiling
• Extend the vertical guideline onto the ceiling as
shown.
• Center the bracket on the vertical mark, no more
than 6" from the wall. Make sure the arrow is
pointing toward the wall. The bracket can be
mounted flush against the ceiling when clearance
is minimal.
• Mark holes designated for ceiling mount only. Drill
3/16" pilot holes and fasten bracket securely to a
structural support with the hardware provided.
Finished
Ceiling
Vertical
Center Line
Header
Bracket
UP
6" Maximum
Door
Spring
Ceiling Mounting Holes
Lag Screws
5/16"x18x1-7/8"
CEILING MOUNT ONLY
UP
Header
Wall
Garage
Door
The nail hole is for positioning only.
You must use lag screws to mount
the header bracket.
14
Vertical
Center Line
Installation Step 3
Attach the T-rail to the Header Bracket
• Position the opener on the garage floor below the
header bracket. Use packing material as a
protective base.
If the door spring is in the way you'll need help.
Have someone hold the opener securely on a
temporary support to allow the T-rail to clear the
spring.
• Position the cable pulley bracket against the header
bracket.
• Align the bracket holes and join with a clevis pin as
shown.
• Insert a ring fastener to secure.
Header Wall
Header
Bracket
Cable
Pulley
Bracket
Ring Fastener
T-rail
Header Bracket
Clevis Pin
5/16"x2-3/4 "
Cable
Pulley
Bracket
T-rail
Garage
Door
Temporary
Support
Hardware Shown Actual Size
Clevis Pin
5/16"x2-3/4"
Ring Fastener
15
Installation Step 4
CAUTION
Position the Opener
To prevent damage to steel, aluminum,
fiberglass or glass panel doors, do not rest the
opener on the door without using a 2x4.
Follow instructions which apply to your door
type as illustrated.
SECTIONAL Door & ONE-PIECE Door with Track
A 2x4 laid flat is convenient for setting an ideal
door-to-T-rail distance.
• Raise the opener onto a stepladder.
You will need help at this point if the ladder is
not tall enough.
• Open the door all the way and place a 2x4 laid flat
on the top section beneath the T-rail.
If the top panel hits the trolley when you raise
the door, pull down on the trolley release arm to
disconnect the inner and outer sections. The
trolley can remain disconnected until Step 12 is
completed.
T-rail
2x4
Laid Flat
Door
Stepladder
Trolley
Release Arm
Trolley
ONE-PIECE Door without Track
• With the door fully open and parallel to the floor,
measure the distance from the floor to the top of
the door.
• Using a stepladder as a support, raise the opener
to the same distance as the door from the floor (it
will be at a slight angle as shown).
• The top of the door should be level with the top of
the opener. Do not position the opener more than
2" above this point.
Top of Opener
Top
of Door
Stepladder
16
Installation Step 5
WARNING
Hang the Opener
The opener could fall and injure someone if it
is not properly secured. Fasten the opener
securely to structural supports of the garage.
Two representative installations are shown.
Yours may be different. Hanging brackets should
be angled, Figure 1, to provide rigid support. On
finished ceilings, Figure 2, attach a sturdy metal
bracket to structural supports before installing the
opener. The bracket and fastening hardware are not
supplied. See accessory page 38.
• Measure the distance from each side of the opener
to the structural support.
• Cut both pieces of the hanging bracket to required
lengths.
• Drill 3/16" pilot holes in the structural supports.
• Attach one end of each bracket to a support with
5/16"x1-7/8" lag screws.
• Fasten the opener to the hanging brackets with
5/16"-18x7/8" screws, lock washers and nuts.
• Check to make sure the T-rail is centered over the
door (or in line with the header bracket if the
bracket is not centered above the door).
• Remove the 2x4. Operate the door manually. If the
door hits the rail, raise the header bracket.
Figure 1
Structural
Supports
Measure
Distance
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
Figure 2
Bracket
(Not Supplied)
Grease the top and underside of the
E
rail surface where the trolley
AS
RE
IL G 3A4
RA
8
.
O
slides. A tube of grease is
N
supplied.
— Finished Ceiling —
(Not Supplied)
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
Hardware Shown Actual Size
Lag Screw
5/16"-18x1-7/8"
Nut 5/16"-18
Hidden
Support
Lag Screws
5/16"x1-7/8"
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
Hex Screw
5/16"- 18x7/8"
Lag Screws
5/16"x1-7/8"
Lock Washer 5/16"
17
Installation Step 6
WARNING
Install the Deluxe Lighted
Console Wall Control
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
Install the Wall Control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it
clearly, and there are no obstructions to door
travel.
• Strip 1/4" of insulation from one end of the bell
wire; connect the wire to the two screw terminals
on the back of the Wall Control: white to 2, and
white/red to 1.
• Locate the Wall Control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all
moving parts of the door and door hardware.
Fasten the Wall Control securely with 6ABx1"
screws. If installing into drywall, drill 5/32" holes
and use the anchors provided.
• Run the bell wire up the wall and across the ceiling
to the opener. Use insulated staples to secure the
wire in several places. Be careful not to pierce the
wire with a staple, thereby resulting in a short.
• Receiver terminal screws and the antenna are
located on the right side panel of the opener.
Position the antenna wire as shown.
• Then connect the bell wire to the opener terminal
screws: white to 2; white/red to 1.
• Remember to affix the User Safety Instruction
label to the wall near the Wall Control, and the
Maintenance Instruction label in a prominent
location on the inside of the garage door.
If the label adhesive will not adhere to your garage
wall surface (or becomes loose with time) use tacks
to secure the label alongside the Wall Control.
Do NOT connect the power and operate the
opener at this time. The trolley will travel to the
full open position but will not return to the close
position until the sensor beam is connected and
properly aligned.
See Safety Reversing Sensor Instructions
beginning on page 21.
Page 32 explains how to operate the opener using
the lighted push bar and the Lock & Light features
available on the Deluxe Lighted Console Wall
Control.
Outdoor Key Switch Accessory Connections
To opener terminal screws: white to 2; white/red to 1
Hardware Shown Actual Size
Screw
6ABx1"
Dry Wall Anchors
Opener
Terminal Screws
Insulated
Staples
1
2
3
9
1
7
RED
WHITE
3
9
1
7
3
5
5
KG
KG
SEARS /CRAFTSMAN
1
2
LOCK
Wall Control
Terminal Screws
LIGHT
Lighted
Push Bar
Antenna
18
Installation Step 7
Install the Lights and the Lenses
Install the lights:
• Install a 75 watt maximum light bulb in each
socket. The lights will turn ON and remain lit for
approximately 4-1/2 minutes when power is
connected. Then the lights will turn OFF.
• If the bulbs burn out prematurely due to vibration,
replace them with standard neck "Garage Door
Opener" bulbs.
Lens
Tab
Lens
Guide
Lens
Slot
Install the lenses:
Lens
Tab
• Apply slight pressure on the sides of each lens
and slide the tabs into the slots in the side panels.
• For convenience, the lenses may be installed
after Adjustment Step 4 on page 30.
• Reverse the procedure to remove the lenses.
Lens
Tab
Installation Step 8
WARNING
Attach the Emergency
Release Rope and Handle
Do not use the red handle to pull the door
open or closed. The rope knot could become
untied and you could fall. Use the emergency
release only to disengage the trolley and, if
possible, only when the door is closed.
Garage doors are heavy. If the door is open
when the handle is pulled, the door could
close inadvertently if it is not properly
balanced. Serious injury may result to persons
under the door. Make sure the doorway is clear
of persons and obstructions before pulling
handle when door is open.
Overhand
Knot
Trolley
NOT
ICE
Overhand
Knot
• Thread one end of the rope through the hole in the
top of the red handle so "NOTICE" reads right side
up as shown. Secure with an overhand knot.
The knot should be at least 1" from the end of the
rope to prevent slipping.
• Thread the other end of the rope through the hole in
the release arm of the outer trolley.
• Adjust rope length so the handle is 6 feet above the
floor. Secure with an overhand knot .
If it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.
Trolley
Release Arm
Rope
75 Watt Max.
Light Bulb
Emergency
Release Handle
19
Installation Step 9
WARNING
Electrical Requirements
To prevent electrocution or fire, installation
and wiring must be in compliance with local
electrical and building codes.
Do NOT use an extension cord, 2-wire adapter,
or change the plug in any way to make it fit
your outlet.
To reduce the risk of electric shock, your garage
door opener has a grounding type plug with a third
grounding pin. This plug will only fit into a grounding
type outlet.
If the plug doesn't fit into the outlet you have,
contact a qualified electrician to install the proper
outlet.
To avoid installation difficulties,
do not run the opener at this time.
Right
RIGHT
Wrong
WRONG
If permanent wiring is required by your local code, refer to the following procedure:
WARNING
To prevent electrocution, remove power from
the garage door opener and from the circuit
you plan to use for the permanent connection.
Permanent
Wiring
Connections
To make a permanent connection through the
7/8" diameter hole in the top of the opener
(according to local code):
• Remove the opener cover screws and set the
cover aside.
• Remove the attached 3-prong cord.
• Connect the black (line) wire to the screw on the
brass terminal; the white (neutral) wire to the
screw on the silver terminal; and the ground wire
to the green ground screw. The opener must be
grounded.
• Reinstall the cover.
Ground Tab
Green
Ground
Screw
Ground
Wire
Black
Wire
White Wire
To avoid installation difficulties,
do not run the opener at this time.
20
Black
Wire
The Safety Reversing System
Information you'll need before you begin the installation of the safety reversing sensor.
The safety reversing sensor must be connected
and aligned correctly before the garage door
opener will move in the down direction. This is a
required safety device and cannot be disabled.
WARNING
Without a properly working safety reversing
sensor, persons (particularly children) could
be injured or killed by a closing garage door.
Read and follow all instructions.
To protect small children, install the safety
reversing sensor so that the beam will be no
higher than 4"-6" above the garage floor.
Disconnect power to the garage door opener
before installing the safety reversing sensor.
Installation procedures are the same for sectional
and one-piece doors.
The brackets must be securely fastened to a solid
surface such as the studs on either side of the door,
or add a piece of wood at each location if installing in
masonry construction.
Be sure power to the opener is disconnected.
The sending eye transmits an invisible light beam to
the receiving eye. The units can be installed on
either side of the garage door as long as the sun
never shines directly into the receiving eye lens.
Look at the label on the connector end of each case
to identify the sensors.
The brackets must be connected and fastened so
that the sending and receiving eyes face each other
as shown in Figure 1.
If an obstruction breaks the light beam while the
garage door is closing, the door will stop and
reverse to full open position and the opener lights
will flash for 5 seconds.
The invisible light beam path must be unobstructed.
No part of the garage door (or door tracks, springs,
hinges, rollers or other hardware) can interrupt the
beam while the door is closing. If it does, use a piece
of wood to build out each sensor mounting location to
the minimum depth required for light beam clearance.
Sensor Beam
4-6" max.
above floor
Sensor Beam
4-6" max.
above floor
Invisible Light Beam
Protection Area
Figure 1: Facing the door from inside the garage
21
Installation Step 10
Install the Safety Reversing Sensor
Figure 2
Figures 2 and 3 show assembly of brackets and
"C" wrap based on the recommended installation of
the sensors as shown on page 21.
However, Figures 4 and 5 are variations which may
fit your installation requirements better. Make sure
the wraps and brackets are aligned so the
sensors will face each other across the garage
door.
• Fasten the "C" wraps to the mounting brackets
having square holes, using the hardware shown
in Figure 2.
• Connect each assembly to a slotted bracket, using
the hardware shown in Figure 3.
Note the alignment of the brackets for left and
right sides of the door.
• Finger tighten the lock nuts.
• Use bracket mounting holes as a template to
locate and drill (2) 3/16" diameter pilot holes on
both sides of the garage door, 4"-6" above the
floor but not exceeding 6". (See warning on
page 21.)
• Attach bracket assemblies with 1/4"x1-1/2" lag
screws as shown in Figure 3.
• Adjust right and left side bracket assemblies to the
same distance out from the mounting surface.
Make sure all door hardware obstructions are
cleared. Tighten the nuts securely.
Mounting Bracket
With Square Holes
"C" Wrap
#10-32
Lock Nuts
#10-32x3/8"
Screws
Figure 3
1/4x1-1/2"
Lag Screws
1/4-20x1/2" Carriage Bolts
(with square shoulder)
Inside
Garage
Wall
1/4"-20
Lock Nuts
Mounting Bracket
with Slot
Mounting Bracket
with Square Holes
"C" Wrap
Hardware Shown Actual Size
#10x32
Lock Nut
#10-32x3/8"
Screw
1/4x1-1/2"
Lag Screw
1/4"-20x1/2"
Carriage Bolts
Staples
1/4"-20
Lock Nut
Figure 5
Figure 4
Alternate Wall Mount
Alternate Floor Mount
Inside
Garage
Wall
Inside
Garage
Wall
Indicator Light
Sensor
Mounting Bracket
with Slot
Mounting Bracket
with Square Holes
Mounting Bracket
with Square Holes
"C" Wrap
"C" Wrap
Sensor
Mounting Bracket
with Slot
Attach with
concrete anchors
(not provided)
Indicator Light
Garage
Floor
Garage
Floor
22
• Insert the wire connector into each
sensor and push until you hear a
click, Figure 6. The white tab on the
sensor should be flush with the back
of the connector.
Figure 6
Safety Sensor
Tab should be
flush with back
of connector
White Tab
Push connector in
until you hear a click
Wire Connector
Figure 7
Connect Wire to
Opener Terminals
Bell Wire
Finished
Ceiling
Sensor
Connections
Wall Control
Connections
(dotted line)
1
2
3
Bell Wire
OPENER TERMINAL SCREWS
• Center each sensor unit in a "C" wrap with lenses
pointing toward each other across the door.
• Secure sensors with the hardware shown. Finger
La to
oreja
debe q
tighten the wing nut on the receiving eye
allow
paño con la
for final adjustment. Securely tighten thealsending
posterior del con
eye wing nut.
Wing Nut
Wire
"C" Wrap
Empujar el conector
hasta que escuche
un chasquido leve.
Indicator Light
Sensor
Invisible Light Beam
Protection Area
Sensor
Sensor
1/4-20x1-1/2"
Hex Bolt
Trouble Shooting
1. If the sending eye indicator light does not glow
steadily after installation, check for:
• Electric power to the opener.
• A short in the white or white/black wires. These
can occur under staples or at screw terminal
connections.
• Incorrect wiring between sensors and opener.
• An open wire (wire break).
2. If the sending eye indicator light glows steadily but
the receiving eye indicator light doesn't:
• Check alignment.
• Check for an open wire to the receiving eye.
• Run paired wires from both sensors to the opener.
Use insulated staples to secure wire to wall and
ceiling.
• Strip 1/4" of insulation from each set of wires.
Separate white and white/black wires sufficiently to
connect to the opener terminal screws: white to 2
and white/black to 3.
• Plug in the opener. Make sure the Lock Feature is
off. Green indicator lights in both the sending and
receiving eyes will glow steadily if wiring
connections and alignment are correct.
If the indicator light is off in the receiving eye (and
the invisible light beam path is not obstructed),
alignment is required.
• Loosen the receiving eye wing nut to allow slight
rotation of unit. Adjust sensor vertically and/or
horizontally until the green indicator light glows
with a steady light.
• When indicator lights are glowing steadily in both
units, tighten the wing nut in the receiving eye unit.
Hardware Shown Actual Size
1/4-20x1-1/2"
Hex Bolt
23
Wing Nut
Installation Step 11
CAUTION
Fasten Door Bracket
To prevent damage to steel, aluminum,
fiberglass or glass panel doors, always
reinforce the inside of the door both vertically
and horizontally with an angle iron.
Follow instructions which apply to your door
type as illustrated below or on page 25.
A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should
cover the height of the top panel.
The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of
angle iron are used to create a "U"-shaped support. The best solution is to check with your garage door
manufacturer for an opener installation door reinforcement kit.
SECTIONAL Door Installation Procedure
Header
Bracket
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, aluminum, steel,
doors with glass panel, etc).
Figure 1
Vertical
Reinforcement
Door
Bracket
Location
Lock Washer
5/16"
Carriage Bolt
5/16"-18x2-1/2"
Vertical
Guideline
Door
Bracket
Vertical
Guideline
Nut
5/16"-18
Figure 2
Inside Edge
of Door or
Reinforcement Board
Door
Bracket
• Center the door bracket on the previously marked
vertical guideline used for the header bracket
installation.
• Position the bracket on the face of the door within
the following limits:
A) The top edge of the bracket 2"-4" below the top
edge of the door.
B) The top edge of the bracket directly below any
structural support across the top of the door.
• Mark and drill 5/16" left and right fastening holes.
Secure the bracket as shown in Figure 1 if there is
vertical reinforcement.
If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes
for the door bracket, position the door plate over the
door bracket as shown in Figure 2. Fasten securely
with hardware shown in Figure 1.
Door Bracket
Plate
Hardware Shown Actual Size
Nut 5/16-18
Lock Washer 5/16"
Carriage Bolt
5/16"-18x2-1/2"
24
All ONE-PIECE Door Installation Procedure
Please read and comply with the warnings and reinforcement instructions on page 24.
They apply to one-piece doors also.
Header Wall
– Finished Ceiling –
2x4 Support
Header
Bracket
Door
Bracket
Horizontal and vertical
reinforcement is needed for
lightweight garage doors
(fiberglass, aluminum, steel,
door with glass panel, etc.).
Optional
Placement
of Door
Bracket
Vertical
Centerline of
Garage Door
Nut
5/16"-18
Lock Washer
5/16"
Door
Bracket
Top of Door
(Inside Garage)
Top Edge
of Door
Optional
Placement
For a door with no
exposed framing or for
the optional installation,
use 5/16"x1-1/2" lag
screw (not supplied) to
fasten door bracket.
• Center the bracket on the top of the door, in line
with the header bracket as shown. Mark holes.
• Drill 5/16" pilot holes and fasten the door bracket
with hardware supplied.
If the door has no exposed framing, drill 3/16" pilot
holes and fasten the bracket with 5/16"x1-1/2" lag
screws (not supplied) to the top of the door.
The door bracket may be installed on the top
edge of the door if required for your installation.
(Refer to the dotted line optional placement
drawing.) Drill 3/16" pilot holes and substitute
5/16"x1-1/2" lag screws (not supplied) to fasten
the bracket to the door.
Carriage Bolt
5/16"-18x2-1/2"
Hardware Shown Actual Size
Nut 5/16"-18
Lock Washer 5/16"
Carriage Bolt
5/16"-18x2-1/2"
25
Installation Step 12
Connect Door Arm to Trolley
Follow instructions which apply to your door
type as illustrated below and on page 27.
SECTIONAL Doors Only
Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley
from the inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in
Figures 1, 2 and 3.
Figure 1:
• Fasten straight door arm section to outer trolley
with a clevis pin. Secure the connection with a ring
fastener.
• Fasten curved door arm to the door bracket in the
same way as shown.
Figure 2:
• Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far
apart as possible to increase door arm rigidity.
Inner Trolley
Outer Trolley
Lock
Washers
5/16"
Clevis
Pin
Ring
Fastener
Rope
Emergency
Release
Handle
Nuts
5/16"-18
Door
Bracket
Straight
Door Arm
Door Bracket
Curved
Door Arm
Clevis Pin
Screws
5/16"-18x7/8"
Figure 1
Figure 2
Hole Alignment Alternative
Figure 3:
• If holes in curved arm are above holes in straight
arm, disconnect straight arm. Cut about 6" from
the solid end. Reconnect to trolley with cut end
down as shown.
• Bring arm sections together.
• Find two pairs of holes that line up and join with
screws, lock washers and nuts.
Lock
Washers
5/16"
Hardware Shown Actual Size
Nuts
5/16"-18
Nut 5/16"-18
Lock Washer 5/16"
Screws
5/16"-18x7/8"
Ring Fastener
Cut This End
Figure 3
Hex Screw
5/16"-18x7/8"
Clevis Pin
5/16"x1"
Proceed to Adjustment Step 1, page 28. Trolley will re-engage automatically when the opener is operated.
26
All ONE-PIECE Doors
Door
Bracket
Assemble the Door Arm:
• Fasten the straight and curved door arm sections
together to the longest possible length, with a 2 or
3 hole overlap.
• With the door closed, connect the straight door
arm section to the door bracket with a clevis pin.
• Secure with a ring fastener.
Ring
Fastener
Lock
Washers
5/16"
Clevis Pin
Nuts
5/16"-18
Straight
Arm
Screws
5/16"-18x7/8
Curved
Door Arm
On one-piece doors, before connecting the door arm to the trolley the travel limits must be adjusted. Limit adjustment screws are located on the left side panel as shown on page 28. Follow adjustment procedures below.
Fully Closed
Trolley
Fully Open
Trolley
Door Arm
Closed
Door
Door Arm
Connector Hole
Open Door
Door Arm
Connector Hole
Door with
Backward Slant
Door Arm
Adjustment Procedures for One-Piece Doors
Open Door Adjustment:
Decrease UP limit
• Turn the UP limit adjustment screw counterclockwise 5-1/2 turns.
• Press the Wall Control push bar. The trolley will
travel to the fully open position.
• Manually raise the door to the open position
(parallel to the floor), and lift the door arm to the
trolley. The arm should touch the trolley just in
back of the door arm connector hole. Refer to the
fully open trolley/door arm positions in the
illustration. If the arm does not extend far enough,
adjust the limit further. One full turn equals 2" of
trolley travel.
Closed Door Adjustment:
Decrease DOWN limit
• Turn the DOWN limit adjustment screw clockwise
5 complete turns.
• Press the Wall Control push bar. The trolley will
travel to the fully closed position.
• Manually close the door and lift the door arm to the
trolley. The arm should touch the trolley just ahead
of the door arm connector hole. Refer to the fully
closed trolley/door arm positions in the illustration. If
the arm is behind the connector hole, adjust the limit
further. One full turn equals 2" of trolley travel.
Connect the door arm to the trolley.
• Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may
be necessary to lift the door slightly to make the connection.
• Secure with a ring fastener.
• Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position
as shown in the illustration, decrease the UP limit until the door is parallel to the floor.
27
Adjustment Section: Pages 28 – 30
Adjustment Step 1
WARNING
Adjust the UP and DOWN Limits
Do not make any limit adjustments until the
safety reversing sensors are completely
installed.
Improper adjustment of the travel limits will
interfere with the proper operation of the
safety reverse system. The door might not
reverse properly when required and could
seriously injure or kill someone under it. Test
the safety reverse system following all
adjustments to the travel limits. See page 30.
Limit adjustment settings regulate the points at
which the door will stop when moving up or down.
The door will stop in the up direction if anything
interferes with door travel. The door will reverse in
the down direction if anything interferes with the
door travel (including binding or unbalanced doors).
To operate the opener, press the Wall Control push
bar. Run the opener through a complete travel
cycle.
• Does the door open and close completely?
• Does the door stay closed and not reverse
unintentionally when fully closed?
If your door passes both of these tests, no limit
adjustments are necessary.
Left Side Panel
RESIDENTIAL DOOR OPENER
Sears, Roebuck & Co. - USA
®
VOLTS
120
AMP.
Hz
5.0
H.P.
196L
LISTED
MFG. DATE
60
IN ALL CORRESPONDENCE REGARDING
THIS ARTICLE ALWAYS MENTION
MODEL
SERIAL NO.
FOR SERVICE INFORMATION ON RADIO CONTROLS REFER TO MODEL
NOS. ON RECEIVER AND TRANSMITTER UNITS. ORDER
REPLACEMENT PARTS BY MAIL OR THRU ANY OF OUR RETAIL STORES.
ASSEMBLED IN MEXICO
132B1632-11
Limit Adjustment
Screws
INCREASE INCREASE
DOWN
UP
TRAVEL
TRAVEL
Adjustment Label
Adjustment procedures are outlined below. Run the opener through a complete travel cycle after each
adjustment.
Repeated operation of the opener during adjustment procedures may cause the motor to overheat and
shut off. Simply wait 15 minutes and try again.
Read the procedures carefully before proceeding to Adjustment Step 2. Use a screwdriver to make limit
adjustments.
How and When to Adjust the Limits
If the door does not open completely
but opens at least five feet
Increase up travel. Turn the UP limit adjustment
screw clockwise. One turn equals 2" of travel.
If door does not open at least 5 feet: Adjust the
UP (open) force as explained in Adjustment Step 2.
If the opener reverses in fully closed position
Decrease down travel. Turn the DOWN limit
adjustment screw clockwise. One turn equals 2" of
travel.
If the door reverses when closing and
there is no visible interference to travel cycle
If the opener lights are flashing, the Safety Reversing
Sensor is obstructed. Remove the obstruction.
Test the door for binding: Pull the emergency release
handle. Manually open and close the door. If the door
is binding, call for garage door service. If the door is
not binding or unbalanced, adjust the DOWN (close)
force. See Adjustment Step 2.
If the door does not close completely
Increase down travel. Turn the DOWN limit
adjustment screw counterclockwise. One turn
equals 2" of travel.
If door still won't close completely, try lengthening
the door arm. (See Page 26.)
If you have adjusted the door arm to the maximum
length and the door still will not close completely,
lower the header bracket. See Installation Step 1,
pages 12 and 13.
28
Adjustment Step 2
WARNING
Adjust the Force
Too much force on the door will interfere with
the proper operation of the safety reverse
system. The door might not reverse properly
when required and could seriously injure or
kill someone under it. Do not increase the
force beyond the minimum amount required
to close the door. Do not use the force
adjustments to compensate for a binding or
sticking garage door. Test the safety reverse
system following all adjustments to force
levels. See page 30.
Force adjustment controls are located on the right
side panel of the opener. Force adjustment settings
regulate the amount of power required to open and
close the door.
The door will stop in the up direction if anything
interferes with its travel. The door will reverse in the
down direction if anything interferes with its travel
(including binding or unbalanced doors).
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down
direction and stops in the up direction. Weather
conditions can affect the door movement, so
occasional adjustment may be needed.
The maximum force adjustment range is 260 degrees,
about 3/4 of a complete turn. Do not force controls
beyond that point. Turn force adjustment controls
with a screwdriver.
Force Adjustment
Controls
1
3
2
9
1
7
9
1
7
3
9
3
9
1
7
3
5
5
KG
KG
1
7
3
5
5
KG
KG
Right Side Panel
Adjustment Label
How and When to Adjust the Forces
Test the DOWN (close) force
Grasp the door bottom when the door is about
halfway through DOWN (close) travel. The door
should reverse. Reversal halfway through down
travel does not guarantee reversal on a two-inch
obstruction. See page 30. If the door is hard to
hold or doesn't reverse, decrease the DOWN (close)
force by turning the control counterclockwise.
Make 10 degree turn adjustments until the door
reverses normally. After each adjustment, run the
opener through a complete cycle.
Make 10 degree turn adjustments until the door stops
easily. After each adjustment, run the opener through
a complete travel cycle.
If the door doesn't open at least 5 feet
Increase UP (Open) force by turning the control
clockwise. Make 10 degree turn adjustments until
door opens completely. Re-adjust the UP limit if
necessary. After each adjustment, run the opener
through a complete travel cycle.
If the door reverses during the down (close) cycle
and the opener lights aren't flashing
Increase DOWN (close) force by turning the control
clockwise. Make 10 degree turn adjustments until the
door completes a close cycle. After each adjustment,
run the opener through a complete travel cycle. Do
not increase the force beyond the minimum
amount required to close the door.
Test the UP (open) force
Grasp the door bottom when the door is about
halfway through UP (open) travel. The door should
stop. If the door is hard to hold or doesn't stop,
decrease UP (open) force by turning the control
counterclockwise.
29
Adjustment Step 3
WARNING
Test The Safety Reversing Sensor
Without a properly working safety reversing
sensor, persons (particularly children) could be
seriously injured or killed if trapped by a closing
garage door. Repeat this test once a month.
• Press the remote control push button to open the
door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the
door. The door will not move more than an inch,
and the opener light(s) will flash.
Professional service is required if the opener
closes the door when the safety reversing
sensor is obstructed.
The garage door opener will not close from a
remote control if the indicator light in either
sensor is off (alerting you to the fact that the
sensor is misaligned or obstructed).
The garage door can be closed by pressing and
holding the Wall Control push bar until down travel
is completed.
Safety Reversing Sensor
Adjustment Step 4
Safety Reversing Sensor
WARNING
Test the Safety Reverse System
Failure to test and adjust the safety reverse
system may result in serious injury or death to
persons trapped by a closing garage door.
Repeat this test once a month and adjust as
needed.
Test:
• Place a one-inch board (or a 2x4 laid flat) on the
floor, centered under the garage door.
• Operate the door in the down direction. The door
must reverse on striking the obstruction.
GARAGE DOOR
Adjustment:
If the door stops on the obstruction, it is not traveling
far enough in the down direction.
• Increase the DOWN limit by turning the DOWN
limit adjustment screw counterclockwise 1/4 turn.
• Repeat the test.
On a sectional door, make sure limit
adjustments do not force the door arm beyond a
straight up and down position. See the
illustration on page 26.
• When the door reverses on the one-inch board,
remove the obstruction and run the opener through
3 or 4 complete travel cycles to test adjustment.
If the door will not reverse after repeated
adjustment attempts, call for professional
garage door service.
One-inch Board
(or a 2x4 laid flat)
Important safety check
Repeat Adjustment Steps 1, 2 and 4 after:
• Each adjustment of door arm length, force controls
or limit controls.
• Any repair to or adjustment of the garage door
(including springs and hardware).
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
30
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Do not permit children either to operate or to play with the opener. Keep remote control in a
location inaccessible to children.
3. Operate opener only when the door is in full view and free from any obstruction. Keep the door in
sight until it is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
4. Check safety reversal system monthly. See page 30. The garage door MUST reverse on contact
with a one-inch (or a 2x4 board laid flat) object placed on the floor. If an adjustment is made to
either the force or the limit of travel, both adjustments may be needed and the safety reversal
system must be checked. Failure to properly adjust the opener may result in severe injury or death.
5. If possible, use the emergency release only when the door is in a closed position. Caution should
be taken whenever the disconnect cord is actuated with the door open. Weak or broken springs
may cause the door to fall rapidly, causing injury or death to persons.
6. KEEP GARAGE DOORS PROPERLY BALANCED. See page 3. An improperly balanced door may not
reverse when required and could result in severe injury or death. Repairs to cables, spring
assemblies and other hardware must be made by a professional garage door person.
7. Disconnect the electric power to the garage door opener before making any repairs or removing the
covers.
8.
SAVE THESE INSTRUCTIONS.
Care of Your Opener
The remote control
The opener must learn the code of any new remote
control. Page 33 explains how to program your
receiver and how to erase all codes if required. Self
service of your receiver is not recommended. If
service is needed, contact your nearest Sears
Service Center.
Limit and force adjustment controls
Limit Controls
Force Controls
9
INCREASE INCREASE
DOWN
UP
TRAVEL
TRAVEL
Adjustment Label
(Located on the left side panel)
1
7
3
9
1
7
3
5
5
KG
KG
Adjustment Label
(Located on the right side panel)
The remote control battery
The green test light should glow and the opener
should operate when the remote control is activated.
If the green test light is dim or does not come on,
replace the battery.
The 12 Volt battery should produce power for at least
a year.
Dispose of your old battery properly.
Weather conditions may cause some minor
changes in door operation requiring some readjustments, particularly during the first year of
operation.
Pages 28 and 29 refer to the limit and force
adjustments. Only a screwdriver is required. Follow
the instructions carefully.
Repeat the safety reverse test (page 30) after any
adjustment of limits or force.
Maintenance Schedule
Once a Month
Manually operate door. If it is unbalanced or
binding, call for professional garage door service.
Check to be sure door opens & closes fully.
Adjust limits and/or force if necessary.
(See pages 28 and 29.)
Repeat the safety reverse test. Make any
necessary adjustments (See page 30).
Twice a Year
Check chain tension. Disconnect trolley first.
Adjust if necessary (See page 11).
Once a Year
Oil door rollers, bearings and hinges
The opener does not require additional
lubrication.
Do not grease the door tracks.
31
Operation of Your Opener
Activate the opener with any of the following
devices:
1. The 3-Function Remote control. Hold large push
button down until the door starts to move.
2. The Wall Control. Hold push bar down until the
door starts to move.
3. The Key Switch or Keyless Entry.
When the Opener is Activated:
1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for
entry and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
7. The garage door will reverse in the closing cycle
when the invisible beam is broken. If fully open, the
door will not close when the beam is broken. The
sensor has no effect in the opening cycle.
If the sensor is not installed, or not aligned correctly,
the door can't close from any portable remote control.
It can be closed with the Wall Control, the Key
Switch, or the Keyless Entry, however, by pressing
and holding the push bar until down travel is
complete. If you release the push bar too soon, the
door will reverse.
The opener lights will blink for 5 seconds when the
safety reversing sensor causes the door to reverse.
Opener Lights will turn on under the following
conditions: When the opener is initially plugged in;
when the power is interrupted; when the opener is
activated. They will turn off automatically after 4-1/2
minutes or provide constant light when the Light
feature is activated. Bulb size is 75 watts maximum.
WARNING
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage. If possible, use the emergency
release rope and handle only when the door is
fully closed.
Trolley
Release Arm
Trolley
NO
TIC
E
Emergency
Release Handle
(Pull Down)
To open the door
manually:
The door should be
fully closed if possible.
Pull down on the red
emergency release
handle and lift the door
manually. To
reconnect the door to
the opener, press the
Wall Control push bar.
Manual disconnect
position
The lockout feature
prevents the trolley from
reconnecting automatically.
Pull the emergency handle
down and back (toward the
opener). The door can then
be raised and lowered
manually as often as
necessary. To disengage
the Lockout Feature, pull
the emergency handle
straight down. The trolley
will reconnect on the next
UP or Down operation.
Trolley
Release Arm
Trolley
NOTICE
Emergency
Release Handle
(Pull Down & Back
Towards Opener)
Lockout position
Operation of the Deluxe Lighted Console Wall Control
Lighted Push Bar
Press to open or close the door.
Press again to reverse the door during the closing
cycle or to stop the door while it's opening.
Light Feature
Press the Light button. If the opener lights are off,
they will turn on.
If the opener lights are on, (even in the 4-1/2 minute
automatic cycle) they will turn off.
But if you use the Light button to turn the lights on
and then activate the opener, the lights will turn off
after 4-1/2 minutes.
The Light button will not control the opener lights
when the door is in motion.
Lock Feature
The Lock feature is designed to prevent operation of
the door from portable remote controls. However, the
door will open and close from the Wall Control push
bar, the Key Switch and the Multi-Function Keyless
Entry.
To Activate:
Press and hold the Lock button for 2 seconds. The
push bar light will flash as long as the Lock feature
is on.
To turn off:
Press and hold the Lock button again for
2 seconds.The push bar light will stop flashing.
Normal operation will resume. The Lock feature will
also turn off whenever the "SRT" button on the
opener end panel is activated.
32
Receiver and Remote Control Programming
To comply with FCC rules, adjustment or modifications of this receiver
and/or transmitter are prohibited, except for changing the code setting or
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.
WARNING
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death. Do not allow children
to operate the wall push button(s) or remote
control(s).
A moving garage door could injure or kill
someone under it. Activate the opener only
when you can see the door clearly, it is free of
obstructions, and is properly adjusted.
Your 53000SRT series garage door opener (with
receiver "SRT" button) has been factory set to
operate with the large push button on the remote
control(s). However, you can use either of the two
small buttons, if you prefer. And, the 3-function
remote control(s) can also activate additional
garage door openers and/or light controls.
Below are instructions for programming your opener
to match the other buttons on your remote controls
and any additional remote controls you may
purchase. See available accessories on page 38.
53000SRT Series Garage Door Openers
(With "SRT" Button)
Figure 1
Mini 3-Function
Remote Control
Your "SRT" garage door opener will operate with as
many as four "SRT" portable remote controls and
one Multi-Function Keyless Entry.
Select a remote control push
button to operate opener
To Add A Remote Control
1. Select a remote control push button to operate
the receiver.
2. Press and hold the selected remote control push
button, Figure 1.
3. Then press and release the "SRT" button on the
right side panel of the opener in Figure 2. The
opener light will flash once.
Now the opener will operate when the remote
control push button is pressed.
If you release the remote control push button
before the opener light flashes, the opener will
not accept the code.
Standard 3-Function Remote Control
Figure 2
Garage Door Opener
(With "Smart" Button)
To Change the Selected Push Button
On the Same Remote control
If you decide to use a different remote control button
than originally programmed into the opener, you
must erase all the learned codes and reprogram
each remote control used to operate the garage
door opener.
1
To Erase All Remote control Codes
• Press and hold the "SRT" button on the opener
panel until the indicator light turns off (about 6
seconds). All the codes the opener has learned
will be erased.
• To reprogram, repeat Steps 1, 2 and 3 for each
remote control in use.
3
2
9
1
7
"SRT"
Button
3
33
1
7
3
5
5
KG
KG
Indicator
Light
END PANEL
Code programming instructions are also located
on the opener panel.
9
Having a Problem?
Situation
Probable Cause and Solution
The opener doesn't
operate from either
the Wall Control or
the remote control:
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light,
check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.)
2. Have you disabled all door locks? Review installation instruction warnings on Page 11.
3. Is there a build-up of ice or snow under the door? The door may be frozen to the
ground. Remove any restriction.
4. The garage door spring may be broken. Have it replaced.
5. Repeated operation may have tripped the overload protector in the motor. Wait
15 minutes. Try again.
Opener operates
from the remote
control, but not from
the Wall Control:
1. Is the Wall Control lit? If not, remove the bell wire from the opener terminal screws.
Short the red and white terminals by touching both terminals at the same time with a
piece of wire. If the opener runs, check for a faulty wire connection at the Wall
Control, a short under the staples, or a broken wire.
2. Are the wiring connections correct? Review Step 6, page 18.
The door operates
from the Wall Control,
but not from the
remote control:
1. If your model has the Lock feature, make sure the lock is Off.
2. Is any wall push button flashing? Your opener needs to re-learn a remote control
code. Refer to Instructions on the opener panel.
3. Does the battery test light glow when the remote control push button is pressed? If
not, replace the battery.
4. Program the receiver to match the remote control code.
5. Repeat the receiver programming procedure with all remote controls.
The remote control
has short range:
1. Check the battery test light. If the light is dim, replace the battery.
2. Change the location of the remote control in your car.
3. Check to be sure the antenna on the side or back panel of opener extends fully
downward.
4. Some installations may have shorter range due to a metal door, foil backed
insulation, or metal garage siding.
Opener noise is
disturbing in living
quarters of home:
If operational noise is a problem because of proximity of the opener to the living
quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to
minimize vibration to the house and is easy to install.
The garage door
opens and closes
by itself:
1. Be sure that all remote control push buttons and battery indicator lights are off.
2. Remove the bell wire from the Wall Control terminals and operate from the remote
control only. If this solves the problem, the Wall Control is faulty (replace), or there is
an intermittent short on the wire between the Wall Control and the opener.
The door doesn't
open completely:
1. If the door has been working properly but now doesn't open all the way, increase the
up force. See page 29.
2. Is something obstructing the door? Remove the obstruction or repair the door.
3. If door opens at least 5 feet, the travel limits may need to be increased. One turn
equals 2 inches of travel. See page 28.
Repeat the safety reverse test after the adjustment is complete.
The door stops but
doesn't close
completely:
Review the travel limits adjustment procedures on page 28.
Repeat the safety reverse test after any adjustment of door arm length, close
force or down limit.
34
Having a Problem? (continued)
Situation
Probable Cause & Solution
The door opens but
won't close:
1. If the opener lights blink, check the safety reversing sensor. See page 23.
2. If the opener lights do not blink and it is a new installation, check the down force.
See Adjustment Step 2, page 29. For an existing installation, see below.
Repeat the safety reverse test after the adjustment is complete.
The door reverses for
no apparent reason
and opener lights
don't blink:
1. Is something obstructing the door? Pull the red emergency release handle. Operate
the door manually. If it is unbalanced or binding, call for professional garage door
service.
2. Clear any ice or snow from the garage floor area where the door closes.
3. Review the force adjustment procedures on page 29.
4. If door reverses in the fully closed position, decrease the travel limits (page 28).
Repeat safety reverse test after adjustments to force or travel limits. The need
for occasional adjustment of the force and limit settings is normal. Weather
conditions in particular can affect door travel.
The door reverses for
no apparent reason
and opener lights
blink for 5 seconds
after reversing:
Check the safety reversing sensor. Remove any obstruction or align the receiving eye.
See page 23.
The opener lights:
. . . don't turn on:
Replace the light bulbs (75 watts maximum). Use a standard neck garage door opener
bulb if regular bulb burns out.
. . . don't turn off:
Is the Light feature on? Turn it off.
The opener strains or
maximum force is
needed to operate
door:
The door may be out of balance or the springs are broken. Close the door and use the
emergency release to disconnect the trolley. Open and close the door manually. A properly
balanced door will stay in any point of travel while being supported entirely by its springs. If it
does not, disconnect the opener and call a professional garage door serviceman. Do not
increase the force to operate the opener.
The opener motor
hums briefly, then
won't work:
1. The garage door springs are broken. See above.
2. If the problem occurs on the first operation of the opener, door may be locked. Disable
the door lock. If the chain was removed and reinstalled, the motor may be out of phase.
Remove the chain; cycle the motor to the down position. Observe the drive sprocket.
When it turns in a clockwise direction and stops in the down position, reinstall the chain.
Repeat the safety reverse test after the adjustment is complete.
The opener won't
operate due to
power failure:
1. Use the emergency release to disconnect the trolley. The door can be opened and closed
manually. When the power is restored, press the Wall Control push bar and trolley will
automatically reconnect (unless trolley is in lockout position.) See page 32.
2. The Emergency Key Release accessory (for use on garages with no service door)
disconnects the trolley from outside the garage in case of power failure.
The chain droops
or sags:
It is normal for the chain to droop slightly in the closed door position. Use the
emergency release to disconnect the trolley. If the chain returns to normal height when
the trolley is disengaged and the door reverses on a one-inch board, no adjustments
are needed (see page 11).
35
Repair Parts
Rail Assembly Parts
4
2
3
1
6
5
E
AS
RE
IL G 3A4
.8
NO
RA
RAGE
TO GA
DOOR
4
7
KEY
NO.
PART
NO.
1
2
3
4
5
6
7
1A995
41A3489
1B3117
183B110
83A4
41A3473
41B2616
DESCRIPTION
41A3534
Master link kit
Complete trolley assembly
T-rail – center section
T-rail – end section (each)
Rail grease
Chain and cable
Cable pulley bracket assembly
NOT SHOWN
Rail assembly hardware kit (includes
hardware illustrated on page 7).
Installation Parts
2
1
KEY
NO.
PART
NO.
1
2
3
4
41A4086-1
41A4166
41A4086A
41A4481
5
6
41A3888
41A3592
7
8
9
10
11
12
13
14
10A14
29C128
41A2828
217A238
12B380
12B374
41A4353
41A4373A
15
16
17
18
19
20
178B35
178B34
12B350
12B484
12B483
12B485
41A3535
41A4116
114A1903
4
SEARS /CRAFTSMAN
LOCK
9
5
LIGHT
NOT
3
ICE
6
DESCRIPTION
Lighted console wall control
Lighted push button wall control
Deluxe lighted wall control
Single-function remote control housing & screw
only (no circuit board)
3-function remote control housing & screw only
3-function compact remote control
housing & screw only
12V battery
Remote control visor clip
Emergency rope & handle assy.
2-conductor bell wire - white & white/red
Door bracket plate
Door bracket
Header bracket w/clevis pin & fastener
Safety sensor kit
(receiving and sending eyes)
with 3' 2-conductor bell wire attached
Curved door arm section
Straight door arm section
Hanging brackets
Square hole bracket
"C" wrap bracket
Slotted bracket
NOT SHOWN
Installation hardware bag (includes hardware
illustrated on page 7).
Safety sensor hardware
Owner's manual
36
10
8
7
C
VD
12
CE
ILI
NG
MO
UN
T ON
LY
UP
13
12
11
15
16
17
14
18
19
20
Repair Parts
Opener Assembly Parts
1
2
4
9
7
3
5
6
8
20
8
19
3
18
10
11
12
9
5
15
17
13
14
16
Brown
Wire
(Down)
Contact
LIMIT SWITCH
ASSEMBLY
DN
UP
Drive
Gear
Center Limit
Contact
KEY PART
NO. NO.
1
2
31D380
41C4220A
3
41A2817
4
5
6
41B4245
41C4253
41A4315-6B
7
8
41A4351
175B88
DESCRIPTION
Sprocket cover
Gear and sprocket assembly
Complete with:
Spring washer
Thrust washer
Retaining ring
Bearing plate
Roll pins (2)
Drive gear and worm gear
Helical gear w/retainer and grease
Drive/worm gear kit w/grease
Roll pins (2)
Line cord
Wire harness assembly w/plug
Receiver logic board assembly
Complete with:
Logic board
End panel w/all labels
End panel w/all labels
Light socket
KEY
NO.
PART
NO.
9
10
11
12
13
108D46
30B363
12A373
41A3150
41D3058
14
15
16
17
18
19
20
41A3474
41A2818
41D3452
41C4398A
41A2826
41A2822A
41A4352
41A2825
37
(Up)
Contact
Grey
Wire
Yellow
Wire
DESCRIPTION
Lens
Capacitor - 1/2HP
Capacitor bracket
Terminal block w/screws
Universal replacement motor &
bracket assembly
Complete with: Motor, worm,
bracket, bearing assembly,
RPM sensor
Cover
Helical gear & retainer w/grease
Limit switch assembly
RPM sensor assembly
Shaft bearing kit
Interrupter cup assembly
End panel
NOT SHOWN
Opener assembly hardware kit
(includes screws not designated by
a number in illustration).
Accessories
Sears offers many useful accessories for your garage door opener. They are illustrated below with
Sears model numbers and descriptions.
53702
Emergency Key Release:
Required for a garage with NO
access door.
53759
3-Function Compact Remote
Control:
With key ring & Velcro fastening
strip.
53703
Outdoor Key Switch:
Opens the garage door automatically
from outside when remote control is
not handy.
53773
Wire-In Light Control:
Controls interior or exterior lights.
Wires into the electrical box like a
dimmer switch.
53704
8 Foot Rail Extension
To allow an 8 foot door to open fully.
53774
Plug-In Light Control:
Controls interior lights. Plugs into a
wall receptacle.
53705
10 Foot Rail Extension:
To allow a 10 foot door to open fully.
53776
Multi-Function Keyless Entry:
Enables homeowner to operate
garage door opener from outside
by entering code on specially
designed keyboard.
53709
Door Clearance Brackets:
(For Sectional Doors Only)
Replace top brackets and rollers on
door to reduce height of door travel.
For use when installing opener in
garage with low headroom
clearance.
53779
3-Function Standard Size
Remote control:
Includes visor clip.
53714
Support Bracket:
For finished ceilings or where you require additional support based on garage construction.
Includes bracket and fastening hardware.
38
Index
Access Door/Outside Key Release Accessory ...............................................................................................4, 5
Chain Tension ..............................................................................................................................................4, 5, 11
Electrical Safety Warnings........................................................................................................................2, 20, 31
Garage Door
Testing for balance, binding and sticking...................................................................................................3, 28, 31
Determining high point of travel:
Sectional door...................................................................................................................................................12
One-piece door .................................................................................................................................................13
Disabling existing locks....................................................................................................................................3, 11
Door clearance brackets (for garages with low headroom) ...........................................................................12, 38
Force controls
Adjustment procedures.................................................................................................................................4, 29
Problems that might require force adjustments ..........................................................................................34, 35
Safety warnings ..........................................................................................................................................29, 31
Door hardware .....................................................................................................................3, 9, 11, 12, 18, 31, 32
Maintenance instruction label ........................................................................................................................11, 28
Reinforcement requirements ...........................................................................................................................4, 24
Removing of all ropes .......................................................................................................................................3, 11
Possible door damage ...................................................................................................................................16, 24
Travel limits
Adjustment procedures.....................................................................................................................................28
Problems that might require limit adjustments............................................................................................34, 35
Safety warnings ..........................................................................................................................................28, 31
Manual (Emergency) Release Rope & Handle
Lockout feature ....................................................................................................................................................32
Manual disconnect...............................................................................................................................................32
Safety warnings .................................................................................................................................11, 19, 31, 32
Opener Terminals
Wall control connections......................................................................................................................................18
Safety reversing sensor connections...................................................................................................................23
Outdoor key switch accessory connections.........................................................................................................18
Operational Noise
Sprocket noise .....................................................................................................................................................11
Vibration noise (isolator kit) .................................................................................................................................34
Receiver and Remote Control
Programming the receiver ...................................................................................................................................33
Erasing all codes .................................................................................................................................................33
Activating other openers ......................................................................................................................................33
Safety warning .....................................................................................................................................................33
Problems with remote control operation ..............................................................................................................34
Safety Reverse Test Procedure..........................................................................................................................30
Testing required.................................................................................................................................11, 30, 34, 35
Safety reverse system problems
Securing header bracket to wall .......................................................................................................................12
Adjusting travel limits ........................................................................................................................................28
Applying excessive force on the door ...............................................................................................................29
Buckling or uneven floor .................................................................................................................................4, 5
Safety Warnings.........................................................2, 3, 9, 11, 12, 16, 18, 19, 20, 21, 24, 28, 29, 30, 31, 32, 33
User Instruction Label for garage wall ........................................................................................................11, 18
39
®
OWNER’S
MANUAL
GARAGE DOOR OPENER
For the repair or replacement parts you need
Call 7 am – 7 pm, 7 days a week
Model No.
139.53225SRT1
139.53325SRT1
139.53425SRT1
139.53628SRT1
139.53629SRT1
139.53635SRT1
139.53637SRT1
139.53824SRT1
1-800-366-PART
(1-800-366-7278)
For in-home major brand repair service
Call 24 hours a day, 7 days a week
1-800-4-REPAIR
(1-800-473-7247)
For the location of a
Sears Repair Service Center in your area
Call 24 hours a day, 7 days a week
1-800-488-1222
For information on purchasing a Sears
Maintenance Agreement or to inquire
about an existing Agreement
Call 9 am – 5 pm, Monday-Saturday
1-800-827-6655
The model number
label is located under
the light lens on the
front end panel of
your opener.
When requesting
service or ordering
parts, always provide
the following
information:
■
■
■
■
Product Type
Model Number
Part Number
Part Description
114A1903B
SEARS WARRANTY
FULL 90 DAY WARRANTY ON GARAGE DOOR OPENER
For 90 days from the date of purchase, Sears will repair any defect in material or
workmanship at no charge.
LIMITED WARRANTY
From the 91st day until one year from the date of purchase, Sears will furnish
replacement parts for any defective parts, free of charge. You pay for labor.
LIMITED WARRANTY ON 1/2 HP AND 1/3 HP MOTORS
FOR CRAFTSMAN OPENERS
1/2HP MOTOR: After 1 year and through 5 years, Sears will furnish replacement
parts for any defective parts in motor, free of charge. You pay for labor.
1/3HP MOTOR: After 1 year and through 3 years, Sears will furnish replacement
parts for any defective parts in motor, free of charge. You pay for labor.
LIMITATION ON LIABILITY
Sears will not be liable for loss or damage to property or any incidental or
consequential loss or expense from property damage due directly or indirectly
from the use of this product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty does not cover repairs necessary because of operator abuse or
negligence, including failure to install, adjust and operate the opener according to
instructions contained in the owner's manual.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST
SEARS STORE OR SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
SEARS ROEBUCK AND COMPANY, Dept. 817WA, Hoffman Estates, IL 60179
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
©1995, All Rights Reserved
Printed in Mexico