Samsung SND-6011R Setup guide

NETWORK CAMERA
Network Setup Guide
CONTENTS
CHECKING NETWORK
CONFIGURATION
3
Selecting the network type
11
Configure the network on the PC used for IP
configuration
Launching IP Installer
Configuring IP installer values
How to configure port forwarding
Login
Installing the program needed to launch the
webviewer after connecting to network camera
3
NETWORK CONFIGURATION
11
SETUP SCREEN
37
12
19
22
27
31
37
web viewer-Network Setup
checking network configuration
Configure the network after checking the following.
1. Check whether to use a DDNS server.
- Check whether to use a DDNS for remote monitoring from outside, or to configure the system in the form of
a local network for monitoring only inside the local network.
3. Before installation, check the number and locations of network cameras and the location of the monitoring PC.
4. Check the network devices to be connected to a network camera, such as IP router/hub.
5. Check the port forwarding, ports and protocol required for establishing a camera connection path.
SELECTING THE NETWORK TYPE
Select the type of network that you want to configure based on the following information.
If DDNS server is not used:
As shown in the image below, if the monitoring PC and network camera are connected to the same router, they
will have the same IP range.
Install the IP installer on the local monitoring PC and use the PC for IP configuration.
EX1)
WAN
Modem
Router
Local monitoring PC
Network camera1
...
Network camera n
...
Network camera n
EX2)
WAN
Modem
Router
Local monitoring PC
Network camera 1
Network camera 1
Hub
...
Network camera n
English _3
● CHECKING NETWORK CONFIGURATION
2. Check whether to use a static IP or dynamic IP.
checking network configuration
EX3)
WAN
Modem
Router
Hub
Local monitoring PC
Network camera 1
...
Network camera n
EX4)
WAN
Modem
Router
Hub
Network camera 1
Local monitoring PC
4_ Checking network configuration
...
Network camera n
As shown in the image below, if the monitoring PC and network camera are connected to different routers, the
network camera cannot be configured, even if the IP installer is installed in the local monitoring PC.
In this case, connect the configuration PC or notebook to the router (1) to set up the network camera.
EX5)
● CHECKING NETWORK CONFIGURATION
WAN
Modem
Configuration PC
Router(1)
Network camera 1
...
Network camera n
Router(2)
Local monitoring PC
M
 Remove the PC or laptop for IP configuration after the configuration.
English _5
checking network configuration
If DDNS server is used:
As shown in the image below, if the monitoring PC and network camera are connected to the same router, they
will have the same IP range.
Install the IP Installer on the local PC and use the PC for IP configuration.
EX1)
DDNS
Server
External remote
monitoring PC
Internet
Modem
Router
Local monitoring PC
Network camera1
...
Network camera n
EX2)
DDNS
Server
External remote
monitoring PC
Internet
Modem
Router
Local monitoring PC
Network camera 1
...
Network camera n
Network camera 5
6_ Checking network configuration
Hub
...
Network camera n
EX3)
DDNS
Server
External remote
monitoring PC
Internet
● CHECKING NETWORK CONFIGURATION
Modem
Router
Hub
Local monitoring PC
Network camera1
...
Network camera n
EX4)
DDNS
Server
Internet
External remote
monitoring PC
Modem
Router
Hub
Network camera1
...
Network camera n
Local monitoring PC
English _7
checking network configuration
As shown in the image below, if the monitoring PC and network camera are connected to different routers, the
network camera cannot be configured, even if the IP installer is installed in the local monitoring PC.
Connect another PC or laptop for IP configuration to router (1) and configure the network camera.
EX5)
DDNS
Server
Internet
External remote
monitoring PC
Modem
Configuration PC
Router(1)
Network camera 1
...
Network camera n
Router(2)
Local monitoring PC
As shown in the image below, if the monitoring PC and the network camera are connected to the DSL/Cable/
PPPoE modem directly without connecting to the local network, connect another PC or laptop and use the PC
to configure a network camera IP.
EX6)
DDNS
Server
Internet
External remote
monitoring PC
DSL/Cable/PPPoE
Modem
Network camera
Configuration PC
M
 Remove the PC or laptop for IP configuration after the configuration.
8_ Checking network configuration
If the network environment makes it difficult to configure an IP for the
network camera in a typical way:
J
 It is difficult to change and configure the network, so it is recommended to ask the network administrator of the site to
replace router (2) with a general hub, and connect the network camera.
EX1)
DDNS
Server
Internet
External remote
monitoring PC
Modem
Router(1)
Router(2)
Local monitoring PC
Network camera 1
...
Network camera n
EX2)
DDNS
Server
Internet
External remote
monitoring PC
Modem
Router(1)
Router(2)
Local monitoring PC
Network camera 1
...
Network camera n
English _9
● CHECKING NETWORK CONFIGURATION
As shown in the image below, if two or more routers are located at the upper layer of the network camera, it will
generally be impossible to configure the network camera.
In this environment, it is necessary to convert the router (2) into a general hub equipment (by turning off the
DHCP function in the Router Setup menu so that the IP addresses of the router (1) and (2) do not crash with
each other to make the router (2) operates as it were a general hub equipment) or double port forwarding of
the routers (1) and (2).
checking network configuration
EX3)
WAN
Modem
Router(1)
Router(2)
Local monitoring PC
Network camera 1
...
Network camera n
...
Network camera n
EX4)
WAN
Modem
Router(1)
Router(2)
Local monitoring PC
10_ Checking network configuration
Network camera 1
network configuration
How to check the IP range of the router connected to the network camera.
1. Click Start  Run Windows in the Windows screen and enter “cmd”.
2. Type “ipconfig” in the command window.
Information about the IP of the PC for IP configuration connected to the router will be displayed.
 If the same gateway and subnet mask are used, the IP range is the same because the network camera is
connected to the same router.
Router
Network camera 1
...
Network camera n
IP Installer of PC for
IP configuration
CONFIGURE THE NETWORK ON THE PC USED FOR IP
CONFIGURATION
Connect a PC to configure IP
To launch the IP installer program for IP configuration, connect the PC to the same router in order to have the
same IP range as the network camera.
M
 If there is a local PC within the same IP range, launch the IP installer on the local PC to configure the network.
If there is no local PC within the same IP range, connect another PC to configure an IP.
Router(1)
Network camera 1
IP Installer of PC for
IP configuration
Router(2)
...
Network camera n
English _11
● NETWORK CONFIGURATION
M
network configuration
How to configure the network environment of the PC used for IP
configuration
1. Open the network environment configuration menu of the
PC connected to the router.
2. Path : Control panel  Network and Sharing Center 
Change adapter settings  Local Area Connection 
Properties  Internet Protocol Version (TCP/IPv4)  Properties
3. Select "Obtain an IP address automatically" and "Obtain
DNS server address automatically.”
M
 If the IP range of the PC used for IP configuration is different
from that of the network camera, the camera will not be
detected, even if you click [Search].
LAUNCHING IP INSTALLER
What is IP Installer?
The IP Installer, launched on the PC for IP configuration, receives MAC address information transmitted from the
network devices with the IP range of the router, and detects network cameras.
If the IP configuring PC (on which the IP Installer is installed) and the network camera are connected to different
routers and their IP ranges are different, the IP Installer cannot detect network cameras.
EX1) In the following network structure, a MAC address of the network camera is not transmitted to outside
router (2), and a network camera is not detected on the IP Installer of the local PC.
Router(1)
Router(2)
Network camera 1
IP Installer of PC for
IP configuration
...
Network camera n
EX2) The IP configuring PC, on which the IP Installer is installed, must be located in the same IP range of the
router with the network camera in order to detect network cameras.
Router(1)
Network camera 1
IP Installer of PC for
IP configuration
12_ network configuration
Router(2)
...
Network camera n
If DDNS server is not used:
In the following case, launch the IP Installer on the local monitoring PC.
EX1)
● NETWORK CONFIGURATION
WAN
Modem
Router
Local monitoring PC
Network camera1
...
Network camera n
...
Network camera n
EX2)
WAN
Modem
Router
Local monitoring PC
Network camera 1
Network camera 1
Hub
...
Network camera n
English _13
network configuration
EX3)
WAN
Modem
Router
Hub
Local monitoring PC
Network camera 1
...
Network camera n
EX4)
WAN
Modem
Router
Network camera 1
Hub
...
Network camera n
Local monitoring PC
In the following case, connect another configuring PC to router (1) and launch the IP Installer.
EX5)
WAN
Modem
Configuration PC
Router(1)
Network camera 1
Router(2)
Local monitoring PC
14_ network configuration
...
Network camera n
If DDNS server is used:
In the following case, launch the IP Installer on the local monitoring PC.
EX1)
● NETWORK CONFIGURATION
DDNS
Server
External remote
monitoring PC
Internet
Modem
Router
Local monitoring PC
Network camera1
...
Network camera n
EX2)
DDNS
Server
External remote
monitoring PC
Internet
Modem
Router
Local monitoring PC
Network camera 1
...
Network camera n
Network camera 5
Hub
...
Network camera n
English _15
network configuration
EX3)
DDNS
Server
External remote
monitoring PC
Internet
Modem
Router
Hub
Local monitoring PC
Network camera1
...
Network camera n
EX4)
DDNS
Server
Internet
External remote
monitoring PC
Modem
Router
Hub
Local monitoring PC
16_ network configuration
Network camera1
...
Network camera n
In the following case, connect another configuring PC to router (1) and launch the IP Installer.
EX5)
DDNS
Server
Internet
External remote
monitoring PC
● NETWORK CONFIGURATION
Modem
Configuration PC
Router(1)
Network camera 1
...
Network camera n
Router(2)
Local monitoring PC
In the following case, connect the configuring PC directly to the network camera and launch the IP Installer.
EX6)
DDNS
Server
Internet
External remote
monitoring PC
DSL/Cable/PPPoE
Modem
Network camera
Configuration PC
English _17
network configuration
Buttons used in IP Installer
b c
Item
m
Description
Device Name
Model name of the connected camera.
Click the column to sort the list by model name.
However, search will be stopped if clicked during the search.
b
Alias
This function is not currently implemented.
c
Mode
Displays either <Static>, <Dynamic> or <PPPoE> for the current network connection status.
MAC(Ethernet)
Address
Ethernet address for the connected camera.
Click the column to sort the list by Ethernet address.
However, search will be stopped if clicked during the search.
IP Address
IP address.
Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
Protocol
Network setting for the camera.
The factory default is “IPv4”.
Cameras with the IPv6 setting will be displayed “IPv6”.
URL
DDNS URL address enabling access from the external Internet.
However, this will be replaced with the <IP Address> of the camera if DDNS registration has failed.
IPv4
Scans for cameras with the IPv4 setting.
IPv6
Scans for cameras with the IPv6 setting.
Activated in an IPv6 compliant environment only.
Search
Scans for cameras that are currently connected to the network.
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
18_ network configuration
Item
Description
Auto Set
The IP Installer automatically configures the network settings.
Manual Set
You should configure the network settings manually.
m
Exit
Exits the IP Installer program.
CONFIGURING IP INSTALLER VALUES
How to configure with a static IP
Notice for Setup with a Static IP
If assigning a static IP to the network camera: If the range of the assigned static IP is close to that of
network devices (such as PC and printer to which IP addresses are assigned), it may cause an IP
assignment error or an IP collision with other network devices after the router is turned off/on or reset. For
this reason, it is recommended to assign IP addresses that are not usually used in other network devices.
Ex) If network devices such as printer and PC use between 192.168.1.1 and 192.168.1.10 in the router:
The network camera should use between 192.168.1.101 and 192.168.1.200.
How to configure IP manually using [Manual Set]:
1. Launch the IP Installer on the PC for IP configuration.
2. Click the [Search] button. A list of network devices using IP
addresses located at the same router is displayed.
3. Check the MAC address information and select a device to
configure.
4. Click the [Manual Set] button. A window to configure an
address and port pops up.
5. Enter the IP range information assigned by the network
administrator or the IP range information (IP Address,
Subnet Mask, Gateway, HTTP Port, VNP Port) that you
want to assign.
6. Type the password authentication number for camera
access and click the [OK] button. Configuration is now
complete.
M
 The password for camera access is identical to the “admin” login password.
Default value is “4321”.
 HTTP Port is used to connect to the camera using web browser.
Default value is “80”.
 VNP Port is to control video transmission.
Default value is “4520”.
English _19
● NETWORK CONFIGURATION
network configuration
How to configure an IP address automatically using [Auto Set]:
1. Launch the IP Installer on the PC for IP configuration.
2. Click the [Search] button. A list of network devices using IP
addresses located at the same router is displayed.
3. Check the MAC address information and select a device to
configure.
4. Click on the [Auto Set] button.
[Auto Setting] window with IP Address, Subnet Mask and
Gateway entered pops up.
5. Type the password authentication number for camera
access and click the [OK] button. Configuration is now
complete.
M
 The password for camera access is identical to the “admin”
login password.
Default value is “4321”.
 VNP Port is to control video transmission.
Default value is “4520”.
Notice for Installer Setup
1. If two or more network cameras are connected to the router, you should configure the IP and portrelated parts differently.
Category
Camera #1
Camera #2
IP related settings
IP Address
Subnet Mask
Gateway
192.168.1.100
255.255.255.0
192.168.1.1
192.168.1.101
255.255.255.0
192.168.1.1
Port related settings
HTTP Port
VNP Port
8080
4520
8081
4521
2. If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar of
the Internet browser before you can access the camera
ex) http://IP address : HTTP Port  http://192.168.1.100:8080)
20_ network configuration
How to configure with a dynamic IP
J
 If the network camera is set to use a dynamic IP, the monitoring PC program in the local network environment or
in an external remote location may not detect the network camera. This is because IP and port may be changed
when the router power is reset or recovered from a failure.
To solve such problems, it is recommended to set up the port forwarding in the higher router layer.
Refer to “How to configure port forwarding” to learn more about how to configure port forwarding. (Page 22)
How to check and configure a dynamic IP address
1. Launch the IP Installer on the PC for IP configuration.
2. Click the [Search] button.
A list of network devices, whose IP addresses were
assigned by the DHCP of the IP router located at the same
router, is displayed.
3. Check the MAC address information and select a device to
configure.
4. Click the [Manual Set] button. You can check assigned IP
from DHCP in the generated window.
5. Click the [OK] button. Configuration is now complete.
M
 The password for camera access is identical to the “admin”
login password.
Default value is “4321”.
 HTTP Port is used to connect to the camera using web browser.
Default value is “80”.
 VNP Port is to control video transmission.
Default value is “4520”.
English _21
● NETWORK CONFIGURATION
Notice for Setup with a Dynamic IP
A dynamic IP allows you to use IP address resources effectively. It is needed when assigning an IP address
using a DHCP server in a LAN environment, when assigning an IP address using a DHCP of a router in a
local network, or when connecting a network camera to a modem that supports DHCP.
network configuration
HOW TO CONFIGURE PORT FORWARDING
What is port forwarding?
If using a dynamic IP through the DHCP configuration of a router, the port forwarding function allows the
router to assign a static IP and camera for a specific network camera when a monitoring PC program
connects to a specific network camera.
In addition, when the router power is reset or recovered from a failure and its IP and port are changed, it
prevents the monitoring PC program from not finding its network camera.
J
 When a monitoring PC program connects to an internal network camera using a DDNS server, port forwarding
must be set. If the network camera’s IP and port are not configured through port forwarding, a connection cannot
be made.
External remote
monitoring PC
DDNS
Server
Internet
Modem
Router
Port forwarding port
allocation
ports XXX
ports YYY
Network camera1
22_ network configuration
...
Network camera n
External remote
monitoring PC
● NETWORK CONFIGURATION
DDNS
Server
Internet
Modem
Router
Network camera1
...
Network camera n
Setting up Port Range Forward for several network cameras
When several network cameras are connected to one Broadband Router device, you should forward the TCP
943 port of the router to the TCP 943 port of a connected camera.
User

M

Internet
Start
943
3000
3001
4520
4521
8080
8081
Broadband Router
End
Protocol
943
TCP
3000
TCP/UDP
3001
TCP/UDP
4520
TCP/UDP
4521
TCP/UDP
8080
TCP/UDP
8081
TCP/UDP
IP Address
192.168.1.100
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101


Camera1 (192.168.1.100)
HTTP Port
8080
Device port
4520
RTSP Port
3000
Policy Server Port
943
Camera2 (192.168.1.101)
HTTP Port
8081
Device port
4521
RTSP Port
3001
Policy Server Port
943
 TCP 943 port is a port for the Silverlight policy server of a camera, you cannot change the Silverlight policy server port
of a camera.
 Set manually in router setup menu to set port forwarding.
Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play)
function.
After connecting the network camera, set <Quick connect> of <Samsung DDNS> to <On> in the “Setup 
Network  DDNS” menu.
English _23
network configuration
How to configure the CISCO router
1. From the Setup menu of the Broadband Router, select
<Applications & Gaming> - <Port Range Forward>.
For setting the port range forward for a third-party
Broadband Router, refer to the user guide of that
Broadband Router.
2. Select <TCP> and <UDP Port> for each connected
camera to the Broadband Router.
Each port number for the Broadband Router should match
that specified in <Setup> - <Network> - <Port> from the
camera’s web viewer menu.
3. When done, click [Save Settings].
Your settings will be saved.
M
 Above sample instructions are based on the CISCO’s Broadband Router.
 The settings may differ depending on the connected Broadband Router model.
For more information, refer to the user manual of the applicable router.
24_ network configuration
Setting page addresses for each router manufacturer and how to log in to each router
M
 The following information may be subject to change by the manufacturer.
Router Manufacturer
Setting page IP address
ID / Password
http://192.168.123.254
admin/admin
Zio
http://192.168.10.1
Wavecast
http://192.168.200.254
http://192.168.25.1
admin/admin
Linksys
http://192.168.1.1
admin/1234 blank/admin
Belkin
http://192.168.2.1
Netgear
http://192.168.0.1
admin/password
admin/1234
Netop
http://192.168.0.1
admin/admin
Neple
http://192.168.10.1
admin
Levelone
http://192.168.123.254
NETWEEN
http://192.168.1.1
NEXT
http://192.168.100.1
http://192.168.0.1
Imation
http://192.168.10.1
ASUS
http://192.168.10.1
SMC
http://192.168.2.1
iptime
http://192.168.0.1
QookHub
HomeHub
http://172.30.1.254
http://172.30.1.254:8899
ktuser/megaap
ktroot/nespot
LGU+ (model name NAPL,CAPL)
http://192.168.123.254
admin
MyLGtv
http://192.168.219.1
user/power
admin/power
Sktelesys
http://192.168.15.1:62207
root/skb_ipdcp
SK broadband(DVW-2000N)
http://192.168.25.1
admin/admin
SKtv (MW-2010R)
http://192.168.20.1
admin/skbiptv
root/1234 or admin
Anygate
http://192.168.10.1
Buffalo
http://192.168.11.1
root/blank
Unicorn
http://192.168.123.254
admin or admin/admin
LG axler
http://192.168.10.1
D-link
http://192.168.0.1
● NETWORK CONFIGURATION
Samsung
admin/admin
smcadmin
admin/blank
English _25
network configuration
How to enter the port forwarding menu of each router manufacturer
M
 The following information may be subject to change by the manufacturer.
Router Manufacturer
Enter the settings menu of each
Samsung
Advanced Settings  Forwarding  Virtual Server (Port forwarding)
Zio
NAT  Port forwarding
Wavecast
Advanced Settings  Port forwarding, Firewall  Port forwarding
Linksys
Applications & Gaming  Port Range Forward
Belkin
Firewall  Virtual Server
Netgear
Advanced  Port forwarding  Add Custom Service
Netop
Firewall settings  Virtual server settings
Neple
Advanced feature settings  Virtual server
Levelone
Forwarding rule  Virtual server
NETWEEN
Advanced settings  NAT  Port forwarding
NEXT
NAT  Virtual server (Port forwarding)
Imation
Advanced feature settings  Virtual server
ASUS
NAT settings  Virtual server
SMC
Advanced settings  NAT  Virtual server settings
iptime
Administrative tools  Advanced settings  Port forwarding settings
QookHub
HomeHub
Advanced settings  Traffic management  Port forwarding settings
LGU+ (model name NAPL,CAPL)
Advanced settings  NAT settings  Port forwarding
MyLGtv
Network settings  NAT settings  Port forwarding at the bottom
Sktelesys
Firewall  Policies  Port Forwarding
SK broadband (DVW-2000N)
Firewall  Port forwarding
SKtv (MW-2010R)
NAT  Port Forwarding
Anygate
Expert settings  Traffic management  Port forwarding
Buffalo
Game port  Port forwarding
Unicorn
Virtual server  Port forwarding, Port forwarding  Virtual server
LG axler
Advanced menu  Port forwarding
D-link
Advanced  Port forwarding (or virtual server)
26_ network configuration
LOGIN
Login by connecting to a network camera.
● NETWORK CONFIGURATION
Camera connection (login) through the IP Installer
1. Launch the IP Installer.
2. Click the [Search] button to find connected cameras.
3. Select the network camera that you want to connect and
double-click on it.
An Internet browser is launched.
4. Enter the <User name> and <Password> to login when
the login window appears.
Camera connection (login) through the Internet browser)
1. Launch the Internet browser.
2. Enter the IP address of the network camera in the address bar.
Ex) IP address (IPv4): http://192.168.1.100
IP address (iPv6): [2001:230:abcd:ffff:0000:0000:ffff:1111]
3. If HTTP port is not ‘80’, enter the IP address and HTTP port
number of the network camera.
Ex) Enter “http://192.168.1.100:8080”
4. Enter the <User name> and <Password> to login when
the login window appears.
English _27
network configuration
Description of DDNS Server Operation
1. Main DDNS-related information
- DDNS URL address: http://www.samsungipolis.com/Product ID
2. DDNS server operation
① To use the Samsung DDNS, visit the iPOLiS homepage (www.samsungipolis.com) and login with the
product ID of camera 1/camera 2 installed in the site.
② Sign up for a membership and register your product on the DDNS server.
③ Connect the camera 1/camera 2 through the webview.
You may check the option of Samsung DDNS activation in the DDNS configuration menu to use the
DDNS.
 The camera periodically transmits its own IP address to the DDNS server on the network once a camera product ID is
M
registered on the DDNS server and the camera DDNS option is activated.
 When an external remote monitoring PC attempts to connect to camera 1/camera 2 for the purpose of monitoring, it
connects to the DDNS server to receive the latest address of camera 1/camera 2.
 The external remote monitoring PC receives the latest IP address from the DDNS server and connects to camera 1/
camera 2 using the latest IP address to receive video images.
DDNS
Server
External remote
monitoring PC
Internet
c
Router
Network
camera 1
c
Modem
...
b
28_ network configuration
Network
camera n
Register the product on the DDNS server.
b
Connect to camera 1/camera 2 through the webviewer
and check the option of Samsung DDNS activation.
c
Camera1/ camera 2 periodically transmits its own IP
address to the DDNS server.
It connects to the DDNS server to receive the latest
address of camera 1/camera 2.
The external remote monitoring PC receives the latest IP
address from the DDNS server and connects to camera 1/
camera 2 using the latest IP address to receive video
images.
Log in the camera by using a remote PC through the DDNS server
DDNS registration
1. Visit the Samsung DDNS Site http://www.samsungipolis.
com to sign up for a membership.
● NETWORK CONFIGURATION
2. From the top menu bar, select <DDNS SERVICE> - <MY
DDNS>.
3. Click [PRODUCT REGISTRATION].
4. Enter the product ID.
 You must perform the duplicate check for the ID that you entered.
5. Select a <CLASSIFICATION > and specify the <MODEL
NUMBER>.
6. Specify the product location with a description if necessary.
7. Click [REGISTRATION ].
English _29
network configuration
Accessing the network camera connected to the local network.
Since using the IP Installer on a remote computer that is not in the Broadband Router’s network cluster is not
allowed, users can access cameras within a Broadband Router’s network by using the camera’s DDNS URL.
1. Before you can access a camera in the Broadband Router network, you should have set the port range
forward for the Broadband Router.
2. Launch an Internet browser on an external remote monitoring PC.
3. Type a DDNS URL address (http://www.samsungipolis.com/Product ID) in the address bar to connect to
the camera.
4. Enter the <User name> and <Password> to login when the login window appears.
Login
When connecting to a camera through the web browser, the login window on the left appears.
Type the name and password of the user to connect to the camera.
1. Enter “admin” in the <User Name> input box.
The administrator ID, “admin”, is fixed and can not be
changed.
2. Enter “4321” in the <Password> input box.
3. Click [OK].
If you have logged in successfully, you will the Live Viewer
screen.
M
 The default user ID is “admin”, and the default password is
“4321”.
 For security purposes, ensure that you change the password in
<System> - <User>.
 The default password can be exposed to a hacking thread so it
is recommended to change the password after installing the
product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
30_ network configuration
INSTALLING THE PROGRAM NEEDED TO LAUNCH THE WEBVIEWER
AFTER CONNECTING TO NETWORK CAMERA
Installing Silverlight Runtime
To install on Windows OS
1. Click <Click Here>.
2. When the file download dialog pops up, click <Run>.
3. When the download is completed, click <Run>.
4. The Silverlight Runtime installation page will be displayed.
<Install now> to proceed with the installation.
5. When done, click <Close>.
English _31
● NETWORK CONFIGURATION
If your PC has not installed Silverlight Runtime or has just installed an old runtime version, you will be redirected
to the Silverlight Runtime installation page automatically when accessing the web viewer.
network configuration
To install on MAC OS
1. Run the file trailing with “.dmg”.
2. Run the install package file automatically created, ending with “.pkg”.
3. Click <Continue>.
4. Select your language on the language selection screen, and
click <Continue>.
5. Click <Agree>.
32_ network configuration
6. Click <Install>.
● NETWORK CONFIGURATION
7. Enter the password of the account currently logged in, and
click <Install Software> and continue.
8. Once completed, click <Close>.
English _33
network configuration
Installing STW WebViewer Plugin
If connecting to a camera for the first time, you will see the installation message. Then, install the required
WebViewer Plugin to access the camera and control the video from it in real time.
1. When the monitoring page is accessed for the very first
time, the installation page is displayed. Click [Click Here] to
begin installation.
J
 If the plug-in installation file download status is suspended at 99% in the Internet Explorer browser, retry it after
selecting “Release SmartScreen filter” in “Tool  SmartScreen filter”.
2. Click [Run] in the message window.
3. Click [Yes] when the notice window saying that all browser
windows will be closed.
4. When the old version of the Web Viewer Plug-in is installed,
a notice window saying the old version will be deleted is
displayed.
Click [Yes] when the notice window is displayed.
M
 Steps 4 and 5 will be skipped if no Web Viewer Plug-in is
installed.
5. Click [OK].
The old version of Web Viewer Plug-in is deleted.
34_ network configuration
6. Click [Install] to begin installation of the Web Viewer Plug-in.
● NETWORK CONFIGURATION
7. Click [Finish].
STW Web Viewer Plug-in installation is completed.
English _35
network configuration
Using the Live Screen
b
c
Item
b
c
Description
Monitoring
Move to the monitoring screen.
Playback
Switch to the monitoring screen that plays recording data in the SD memory.
Setup
Move to the Setup screen.
Viewer Screen
 You can use the mouse wheel to activate the digital zooming in Viewer screen.
Profile type
 When the Web Viewer is connected, the profile information currently using is displayed.
Screen
Optimization
The video size of the camera will switch to as big as the Web browser.
Fix the resolution
Regardless of the resolution setup configured in the camera, it sets the resolution to 640x480. Press it
again to switch back to the default resolution.
Full Screen
Switch the current video to the maximum size of the monitor.
Capture
Saves the snapshot as an image file in the .bmp or .jpg format.
Audio/Microphone
Control
 Only the Audio volume can be controlled.
Alarm output
Activate the Alarm Out port.
Hide the context
menu
The left-corner context menu will disappear but only the menu icon.
36_ network configuration
Displays the Live video on the screen.
You can select a profile type in <Video profile> under the <Video & Audio> setup menu.
Enable Audio and Microphone are control the Audio volume.
setup screen
WEB VIEWER-NETWORK SETUP
Interface
1. From the Setup menu, select the <Network (
)> tab.
네트워크
설정
● SETUP
SCREEN
2. Click <Interface>.
3. Set the <Interface> and <IPv6 setup> as necessary.
• IP type : Select an IP connection type.
- Manual : Specify the IP address, Subnet mask,
Gateway, DNS1, and DNS2.
- DHCP : Specify the DNS1 and DNS2.
- PPPoE : Specify the DNS1, DNS2, ID and Password.
 If you set it to <Manual>, you should specify the IP, Subnet
mask, Gateway, DNS 1 & 2 manually.
•
•
•
•
•
MAC address : Shows the MAC address.
IP address : Displays the current IP address.
Subnet mask : Displays the <Subnet mask> for the set IP.
Gateway : Displays the <Gateway> for the set IP.
DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.
4. Set the <IPv6 setup>.
 Set to <Use> to use IPv6 address.
• Default : Use the default IPv6 address.
• DHCP : Display and use the IPv6 address obtained from the DHCP server.
• Manual : Enter IP address and gateway manually and use it.
5. When done, click [Apply (
J
)].
 The IP addressing system will be defaulted to DHCP. If no DHCP server is found, the previous settings will be restored
automatically.
 Once completed with editing, click [Apply (
)] to apply changes and the browser exits. After a while, connect
again with the changed IP.
English _37
setup screen
Port
1. From the Setup menu, select the <Network (
)> tab.
2. Click <Port>.
3. Type in each item in the Port menu as necessary.
 Neither the port range between 0 and 1023 nor port 3702 is
available.
• HTTP port : HTTP port used to access the camera via the
web browser.
The default is 80(TCP).
 Setting the HTTP port for Safari and Google Chrome browsers to
65535 is not allowed by security policy.
•
•
•
•
M
Device port : Set a port used to transfer video signals with the Samsung protocols.
RTSP port : Used to transfer videos in the RTSP mode; the default is 554.
Web streaming port : Used to transfer videos to the Web Viewer; the default is 4520.
Silverlight policy port : Silverlight is used to permit to acquire a network connection; the default is 943.
 If changed the HTTP port, the browser exits.
Afterwards, address should contain the newly assigned HTTP port trailing the IP.
ex) IP address: 192.168.1.100, HTTP port : Assigned 8080  http://192.168.1.100:8080
(If HTTP port is set to 80, no need to specify the port number)
 The port range of the Web Streaming is between 4502 and 4534. If the Device port is with this effective range, the
Web Streaming port should be specified the same as the Device port.
 You cannot change the Web Streaming/Silverlight policy server port of a camera.
4. When done, click [Apply (
)].
DDNS
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of a camera into a
general Host Name so that the user can easily remember it.
1. From the Setup menu, select the <Network (
)> tab.
2. Click <DDNS>.
3. Select the <DDNS> connection type.
4. Type in the DDNS items according to the selected type.
• Samsung DDNS : Select this if you use the DDNS server
provided by Samsung Techwin.
- Product ID : Enter the product ID that is registered with
the Samsung DDNS service.
- Quick connect : It sets port forwarding automatically
when used with a UPnP (Universal Plug and Play) supporting router.
38_ setup screen
• Public DDNS : Select one of provided public DDNS servers when you use a public DDNS server.
- Service : Select desired public DDNS service server.
- Host name : Enter the name of the host that is registered with the DDNS server.
- User name : Enter the user name for the DDNS service.
5. When done, click [Apply (
J
네트워크
설정
● SETUP
SCREEN
- Password : Enter the password for the DDNS service.
)].
 If selected <Quick connect>, be sure to select Samsung DDNS service.
To connect to the Samsung DDNS in camera setup
1. From the DDNS setup page, set <DDNS> to <Samsung
DDNS>.
2. Provide the <Product ID> that you registered product ID
with the DDNS site.
3. Click [Apply (
)].
When the connection is successfully made, you will see the
message of <(Success)> on the screen.
Configuring public DDNS in Camera Settings
1. Open the DDNS settings page and select <Public DDNS> for <DDNS>.
2. Enter the corresponding site’s host name, user name and password.
3. Click [Apply (
)] button.
If the connection properly establishes, <(Success)> appears.
4. When done, click [Apply (
M
)].
 To use DDNS service properly, both DDNS setup and the router’s port forwarding setup are required.
For port forwarding setup, refer to “How to configure port forwarding”. (page 22)
English _39
setup screen
IP filtering
You can create a list of IPs that you want to grant or deny access to them.
1. From the Setup menu, select the <Network (
)> tab.
2. Click <IP filtering>.
3. Select <Filtering type>.
• Deny : If selecting this, access from those IPs that are
added to the filtering will be restricted.
• Allow : If selecting this, access from only those IPs that are
added to the filtering will be accepted.
)] button.
4. Click the [Add (
The IP list will be created.
5. Provide the IP that you want to grant or deny access from.
When you enter an IP address and a Prefix, the list of IP addresses available will appear in the right-side filter
range column.
M
 If selected <Allow> for IP Filtering and <IPv6 setup> of <Interface> is set to <Use>, both IPv4 and IPv6 addresses
of the computer currently configuring should be assigned.
 The IP address of the computer used for the current setup cannot be added to <Deny>, it should be added to
<Allow>.
 Only the IP addresses that are set to <Use> will be displayed in the filter column.
6. Select an IP to delete from the list.
Click the [Delete (
)] button.
7. When done, click [Apply (
)].
SSL
You can select a secure connection system or install the public certificate for this purpose.
1. From the Setup menu, select the <Network (
)> tab.
2. Click <SSL>.
3. Select a secure connection system.
 To access the camera using HTTPS mode, you have to type the IP
address for the camera in the form of “https://<Camera_IP>”.
If you failed to configure the Web viewer settings in HTTPS mode
with Internet Explorer, edit the Internet options as follows: <Menu
 Tools  Internet Options  Advanced  Security  Uncheck
TLS 1.0, and check TLS 1.1, TLS 1.2>
4. Search for the public certificate that you want to install on the camera.
To install the certificate on the camera, you need to provide a certificate name (it can be arbitrarily assigned
by the user), certificate file issued from the certification authority and a key file.
 The <HTTPS (Secure connection mode using the public certificate)> item will be active only if there exists a public
certificate installed.
5. When done, click [Apply (
40_ setup screen
)].
Installing the certificate
1. Enter the certificate name.
2. Select the certificate file to be installed and certificate key, and click [Install (
)] button.
Deleting the certificate
)] button.
2. To delete a public certificate, you should access the network video decoder in the mode of <HTTP (Do not
use secure connection)> or <HTTPS (Secure connection mode using a unique certificate)>
802.1x
When connecting network, you can choose whether using 802.1x protocol, and then install the certification.
1. From the Setup menu, select the <Network (
)> tab.
2. Click <802.1x>.
3. Set the <IEEE 802.1x setting(EAPOL using EAP-TLS)>.
• Enable IEEE 802.1x : Specify the use of the 802.1x
protocol.
• EAPOL version : Select version 1 or 2.
• ID : Enter the client certificate ID.
• Password : Enter the client private key password. If the
key file used is not encrypted, you don’t need to enter it.
J
 If the connected network device does not support the 802.1x protocol, the protocol will not operate properly even if
you set it.
4. Install/remove the certificate.
• CA certificates : Select a public certificate that contains the public key.
• Client certificate : Select a public certificate that contains the client certificate key.
• Client private key : Select a public certificate that contains the client private key.
5. When done, click [Apply (
)].
To install/remove 802.1x related certificates
1. Press the [Browse (
)] button for each item and select a certificate to install.
2. If no certificate is installed, you will see “Not Available” appearing next to the selected item.
3. Press the [Install (
)] button to start installation with a message of “Installed” next to the item.
4. Press the [Delete (
)] button to remove the certificate.
English _41
네트워크
설정
● SETUP
SCREEN
1. Click [Delete (
setup screen
QoS
You can specify the priority to secure a stable transfer rate for a specific IP.
1. From the Setup menu, select the <Network (
)> tab.
2. Click <QoS>.
)] button.
3. Click the [Add (
The IP list will be created.
4. Enter an IP address to which you will apply QoS.
M
 The default prefix for IPv4 is 32;
For DSCP, the default is set to 63.
 Only the IP addresses that are set to <Use> can be prioritized.
5. Select an IP to delete from the list.
Click the [Delete (
)] button.
6. When done, click [Apply (
)].
SNMP
With the SNMP protocols, the system or network admin can monitor the network devices on a remote site, and
configure the environment settings.
1. From the Setup menu, select the <Network (
)> tab.
2. Click <SNMP>.
3. Specify the <SNMP>.
• Enable SNMP v1 : SNMP version 1 will be active.
• Enable SNMP v2c : SNMP version 2 will be active.
- Read community : Provide the name of the read
community where you can access to the SNMP
information.
The default name is <public>.
- Write community : Provide the name of the write community where you can access to the SNMP
information. The default name is <write>.
• Enable SNMP Trap : SNMP trap is used to send important events and conditions to the Admin.
- Community : Enter the trap community name to receive messages.
- IP address : Enter the IP address to which messages will be sent.
- Authentication failure : It specifies whether an event shall be generated when the community information
is invalid.
- Network connection : It specifies whether an event shall be generated when the network disconnection
is restored.
• Enable SNMP v3 : SNMP version 3 will be active.
- Password : Specify the default password for SNMP version 3. The default password is <admin4321>.
 The default password can be exposed to a hacking thread so it is recommended to change the password after installing the
product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
 Password should be longer than 8 characters, no more than 16 characters.
4. When done, click [Apply (
J
)].
 SNMP v3 is only able to be set when the secure connection mode is HTTPS.
Refer to “SSL”. (page 40)
42_ setup screen
Link-Local IPv4 address
An additional IP address may be assigned to assess the camera from the Link-Local network.
1. From the Setup menu, select the <Network (
)> tab.
2. Click <Link-Local IPv4 address>.
네트워크
설정
● SETUP
SCREEN
3. Set the <Link-Local IPv4 address>.
• Auto configure : It specifies Able or Disable for the LinkLocal IPv4 address.
• IP address : Display the assigned IP address.
• Subnet mask : Display the subnet mask of the assigned
IP.
4. When done, click [Apply (
)].
UPnP discovery
Cameras can be automatically searched in the client and operating system in support of the UPnP protocol.
1. From the Setup menu, select the <Network (
)> tab.
2. Click <UPnP discovery>.
3. Set the <UPnP discovery>.
• UPnP discovery : It specifies Able or Disable for UPnP
Discovery.
• Friendly name : Display the camera name.
Friendly name is displayed in the format of SAMSUNG<Model Name>-<MAC Address>.
M
 In the Windows operating system which basically supports
UPnP, the cameras connected to the network are displayed.
4. When done, click [Apply (
)].
Bonjour
Cameras can be automatically searched in the client and operating system in support of the Bonjour protocol.
1. From the Setup menu, select the <Network (
)> tab.
2. Click <Bonjour>.
3. Set the <Bonjour>.
• Bonjour : It specifies Able or Disable for Bonjour.
• Friendly name : Display the camera name.
Friendly name is displayed in the format of SAMSUNG<Model Name>-<MAC Address>.
4. When done, click [Apply (
M
)].
 In the Mac operating system, which support Bonjour by default, the connected cameras are automatically displayed in
the Bonjour bookmark of the Safari web browser.
If the Bonjour bookmark is not displayed, check Bookmarks Setup in the “Preference” menu.
English _43
setup screen
FTP / E-mail
You can configure the FTP/E-mail server settings so that you can transfer the images taken with camera to your
PC if an event occurs.
1. From the Setup menu, select the <Event (
)> tab.
2. Click <FTP / E-mail>.
3. Select <FTP configuration> or <E-mail configuration>
and enter / select a desired value.
• FTP configuration
- Server address : Enter the IP address of the FTP server
that you transfer the alarm or event images to.
- ID : Enter the user ID with which you will log in to the
FTP server.
- Password : Enter the user account password for logging
into the FTP server.
- Upload directory : Specify the FTP path where you will
transfer the alarm or event images.
- Port : The default port of the FTP server is 21; however, you can use a different port number according
to the FTP server settings.
- Passive mode : Select <On> if you need to connect in passive mode due to the firewall or the FTP
server settings.
• E-mail configuration
- Server address : Enter the IP address of the email server that you transfer the alarm or event images to.
- Use authentication : Select whether to use authorization.
- Use SSL : Specify the use of SSL.
- ID : Enter the user ID for logging into the email server.
- Password : Enter the user account password for logging into the email server.
- Port : The default port of the email server is 25; however, you can use a different port number according
to the email server settings.
- Recipient : Enter the address of the email recipient.
- Sender : Enter the address of the email sender. If the sender address is incorrect, the email from the
sender may be classified as SPAM by the email server and thus may not be sent.
- Subject : Enter a subject for your email.
- Body : Provide the text for the massage. Attach the alarm or event images to the email that you are
preparing.
4. When done, click [Apply (
44_ setup screen
)].
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
www.samsungipolis.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325