Emerson MVME55006E Technical data

MVME7616E Transition Module
Installation and Use
6806800A43B
August 2008
©
Copyright 2008 Emerson
All rights reserved.
Trademarks
Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service
marks of Emerson Electric Co. © 2008 Emerson Electric Co.
All other trademarks are the property of their respective owners.
Intel® is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
Microsoft®, Windows® and Windows Me® are registered trademarks of Microsoft Corporation; and Windows XP™ is a trademark of
Microsoft Corporation.
PICMG®, CompactPCI®, AdvancedTCA™ and the PICMG, CompactPCI and AdvancedTCA logos are registered trademarks of the
PCI Industrial Computer Manufacturers Group.
UNIX® is a registered trademark of The Open Group in the United States and other countries.
Notice
While reasonable efforts have been made to assure the accuracy of this document, Emerson assumes no liability resulting from any
omissions in this document, or from the use of the information obtained therein. Emerson reserves the right to revise this document
and to make changes from time to time in the content hereof without obligation of Emerson to notify any person of such revision or
changes.
Electronic versions of this material may be read online, downloaded for personal use, or referenced in another document as a URL to
a Emerson website. The text itself may not be published commercially in print or electronic form, edited, translated, or otherwise altered
without the permission of Emerson,
It is possible that this publication may contain reference to or information about Emerson products (machines and programs),
programming, or services that are not available in your country. Such references or information must not be construed to mean that
Emerson intends to announce such Emerson products, programming, or services in your country.
Limited and Restricted Rights Legend
If the documentation contained herein is supplied, directly or indirectly, to the U.S. Government, the following notice shall apply unless
otherwise agreed to in writing by Emerson.
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (b)(3) of the Rights in Technical
Data clause at DFARS 252.227-7013 (Nov. 1995) and of the Rights in Noncommercial Computer Software and Documentation clause
at DFARS 252.227-7014 (Jun. 1995).
Contact Address
Emerson Network Power - Embedded Computing
2900 South Diablo Way, Suite 190
Tempe, AZ 85282
USA
Contents
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpacking the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Serial Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Transition Module and P2 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
19
19
22
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.1
3.2
3.3
3.4
3.5
3.6
4
13
13
13
14
15
15
16
16
18
18
18
Hardware Preparation and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1
2.2
2.3
2.4
3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Port Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P2 Adapter Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Three-row P2 Adapter (MVME761-001) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Five-Row P2 Adapter (MVME761-011) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectors and Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCC Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P2 Signal Multiplexing (P2MX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Interface Module Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COM1 and COM2 Asynchronous Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Asynchronous/Synchronous Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
27
29
30
31
Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P2 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Asynchronous Serial Port Connectors (J5/J6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Asynchronous/Synchronous serial Port connectors (J7/J8) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel I/O Port Connector (J4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Connector (J9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P2 Adapter Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MVME7616E Transition Module Installation and Use (6806800A43B)
35
35
36
37
38
39
39
3
Contents
4.7.1
4.7.2
4.7.3
4.7.4
4.7.5
4
3-Row P2 Adapter (J2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-Row P2 Adapter (J3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-Row P2 adapter (J1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMC I/O, 5-Row P2 Adapter (J3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-Row P2 adapter (J4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
40
41
42
43
MVME7616E Transition Module Installation and Use (6806800A43B)
List of Tables
Table 1-1
Table 1-2
Table 1-3
Table 1-4
Table 1-5
Table 1-6
Table 3-1
Table 4-1
Table 4-2
Table 4-3
Table 4-4
Table 4-5
Table 4-6
Table 4-7
Table 4-8
Table 4-9
Table 4-10
Table 4-11
SIM Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MVME761 Transition Module Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-Row P2 Adapter Connectors (MVME761-001) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-Row P2 Adapter Connectors (MVME761-011) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transition Module Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MVME761-0x1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P2 signal multiplexing sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P2 Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COM1 and COM2 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Port 3 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Port 4 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel I/O Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10Base-T/100Base-TX Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-bit SCSI Connector (3-Row P2 adapter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VME Connector (3-Row P2 adapter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16-bit SCSI Connector (5-Row P2 adapter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMC I/O Connector (5-Row P2 adapter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VME Connector (3-Row P2 adapter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MVME7616E Transition Module Installation and Use (6806800A43B)
15
16
17
17
17
18
28
35
36
37
37
38
39
39
40
41
42
43
5
List of Tables
6
MVME7616E Transition Module Installation and Use (6806800A43B)
List of Figures
Figure 1-1
Figure 1-2
Figure 1-3
Figure 2-1
Figure 2-2
Figure 2-3
Figure 2-4
Figure 3-1
Figure 3-2
Figure 3-3
Figure 3-4
Figure 3-5
Figure 3-6
Figure 3-7
Figure 3-8
Figure 3-9
RTM Front Panel and Components Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Three Row P2 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Five Row P2 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Port Interface Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SIM Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the SIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transition Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-Row DIN Backplane P2 Adapter Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-Row DIN Backplane P2 Adapter Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiplex Signal Timing Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA-574 DTE Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA232-DCE Copnfirguration Port 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA232-DCE Configuration Port 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA232-DTE Configuration Port 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA232-DTE Configuration Port 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MVME7616E Transition Module Installation and Use (6806800A43B)
14
15
16
19
20
21
23
26
26
27
29
30
31
32
33
34
7
List of Figures
8
MVME7616E Transition Module Installation and Use (6806800A43B)
About this Manual
Overview of Contents
This manual is divided into the following chapters and appendices:
Chapter 1, General Information
Chapter 2, Hardware Preparation and Installation
Chapter 3, Functional Description
Chapter 4, Connector Pin Assignments
MVME7616E Transition Module Installation and Use provides general information, hardware
preparation, installation instructions and support information for the MVME7616E-001 and
MVME7616E-011 Transition Modules. These transition modules are used as the interface
between the variants of the MVME51005E and MVME55006E Single Board Computers. A P2
adapter module and cable are supplied with the MVME7616E. The MVME7616E will hereafter
be referred to as the MVME761.
As of the printing date of this manual, these I/O module models are available:
Model Number
Description
MVME7616E-001
MVME7616E-011
3-Row Rear Transition Module and P2 Adaptor
5-Row Rear Transition Module and P2 Adaptor
MVME761P26E-001
MVME761P2-6E011
3-Row, P2 Adapter Module Only
5-Row, P2 Adapter Module Only
Related Product
MVME51005E
MVME51105E
MVME Series MVME51005E Single Board Computer
MVME55006E
MVME Series MVME55006E Single Board Computer
IPMC7616E-001
IPMC7616E-002
Multifunction rear I/O PMC module; Ultra-Wide SCSI, one parallel port, three
asynchronous and one synchronous/asynchronous serial port
SIM232DCE5E
SIM232DTE5E
EIA232-DCE serial interface module
EIA232-DTE serial interface module
MVME7616E Transition Module Installation and Use (6806800A43B)
9
About this Manual
Abbreviations
This document uses the following abbreviations:
Abbreviation
Description
AC
Alternating Current
CFM
Cubic Feet per Minute
D/C
Direct Current
DCE
Data Communications Equipment
DIN
Deutsches Insitut für Normung eV
DTE
Data Terminal Equipment
EMI
Electro-Magnetic Interference
ESD
Electro-Static Discharge
FCC
Federal Communications Commission
GND
Ground
I/O
Input/Output
IC
Integrated Circuit
IEEE
Institute of Electrical and Electronics Engineers
PMC
PCI Mezzanine Card
RF
Radio Frequency
RTM
Rear Transition Module
SCSI
Small Computer System Interface
SIM
Serial Interface Module
VME
Versamodule Eurocard
Conventions
The following table describes the conventions used throughout this manual.
10
Notation
Description
0x00000000
Typical notation for hexadecimal numbers (digits
are 0 through F), for example used for addresses
and offsets
0b0000
Same for binary numbers (digits are 0 and 1)
bold
Used to emphasize a word
Screen
Used for on-screen output and code related
elements or commands in body text
Courier + Bold
Used to characterize user input and to separate it
from system output
Reference
Used for references and for table and figure
descriptions
MVME7616E Transition Module Installation and Use (6806800A43B)
About this Manual
Notation
Description
File > Exit
Notation for selecting a submenu
<text>
Notation for variables and keys
[text]
Notation for software buttons to click on the screen
and parameter description
...
Repeated item for example node 1, node 2, ...,
node 12
.
Omission of information from example/command
that is not necessary at the time being
.
.
..
Ranges, for example: 0..4 means one of the
integers 0,1,2,3, and 4 (used in registers)
|
Logical OR
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury
Indicates a hazardous situation which, if not
avoided, may result in minor or moderate injury
Indicates a property damage message
No danger encountered. Pay attention to
important information
Summary of Changes
This manual has been revised and replaces all prior editions.
Part Number
Publication Date
Description
6806800A43A
June 2006
First edition
6806800A43B
August 2008
Updated to Emerson style.
MVME7616E Transition Module Installation and Use (6806800A43B)
11
About this Manual
Comments and Suggestions
We welcome and appreciate your comments on our documentation. We want to know what you
think about our manuals and how we can make them better.
Mail comments to us by filling out the following online form:
http://www.emersonnetworkpowerembeddedcomputing.com/ > Contact Us > Online Form
In “Area of Interest” select “Technical Documentation”. Be sure to include the title, part number,
and revision of the manual and tell us how you used it.
12
MVME7616E Transition Module Installation and Use (6806800A43B)
General Information
1.1
1
Overview
This manual provides general information, hardware preparation, installation instructions, and
a functional description for the MVME761-001 and MVME761-011 Transition Modules.
The MVME761-0x1Transition Module provides the interface between the MVME5100 or
MVME5500
Single Board Computer VMEmodules and various peripheral devices. This module provides
industry standard connectors to simplify customer cable requirements for the serial port, printer,
and Ethernet signals.
1.2
Features
The features of the MVME761-0x1 Transition Module include:
z
1.3
Industry-standard connectors for these interfaces:
–
Two EIA-574 asynchronous serial ports (DTE)
–
Two asynchronous/synchronous serial ports, configured for EIA-232-D (DCE or DTE)
–
One parallel port (IEEE Standard 1284-I compliant)
–
10Base-T/100Base-TX Ethernet
z
Two 60-pin Serial Interface Module (SIM) connectors for configuring the
asynchronous/synchronous serial ports
z
Single-width board
z
Electro-Magnetic Interference (EMI) and Electro-Static Discharge (ESD) protection
General Description
The MVME761-0x1 Transition Module provides the interface between the standard Ethernet,
parallel port, and the serial port connectors on a variety of single board computers. All port I/O
controllers reside on the host VMEmodules. The MVME761 transition module Ethernet and
parallel port circuitry is passive. The serial port circuitry provides multiplexing and buffering
functions (refer to P2 Signal Multiplexing (P2MX) on page 27). The multiplexing function is
transparent to the user.
Both MVME761-0x1 models use the same transition module. The MVME761-001 comes with
a P2 adapter that connects to a 3-row DIN chassis backplane. The MVME761-011 comes with
a P2 adapter that connects to a 5-row DIN chassis backplane.
MVME7616E Transition Module Installation and Use (6806800A43B)
13
General Information
Serial Port Interface Modules
Figure 1-1 shows the MVME761 transition module component layout and the front panel. See
Table 1-2 for a list of the front panel port connectors.
Figure 1-1
RTM Front Panel and Components Side
MVME
761-001
COM1
J5
COM2
J6 DTE
1
DCE
J2
3
SERIAL 3
60
J1
59
2
1
J7
SERIAL 4
60
J12
59
2
1
J8
DTE
DCE
J3
1
3
PARALLEL
J4
P2
10/100 BASET
J9
1910 9609
1.4
Serial Port Interface Modules
You may configure the asynchronous/synchronous serial ports (ports 3 and 4) to the
appropriate interface by installing a Serial Interface Module (SIM). A SIM is a small “plug-in”
printed circuit board that converts the TTL-level synchronous or asynchronous port signals to
industry standard voltage levels used by the ports. The SIM contains the receiver and
transmitter circuits for converting the input and output signals of the host VMEmodule to the
appropriate serial data communication protocol.
14
MVME7616E Transition Module Installation and Use (6806800A43B)
P2 Adapter Boards
General Information
The SIMs for the MVME761 are listed in the following table.
Table 1-1 SIM Part Numbers
Interface
Model Number
Part Number
EIA-232-D DCE
SIM232DCE5E
01-W3876B11A
EIA-232-D DTE
SIM232DTE5E
01-W3877B11A
Additional SIMs may be released. Please see your Emerson representative for a complete list
of SIMS that are available for the MVME761-0x1.
1.5
P2 Adapter Boards
The P2 adapters route the asynchronous and synchronous port, printer port, and Ethernet
signals to the MVME761 transition module.
1.6
Three-row P2 Adapter (MVME761-001)
The P2 adapter for the MVME761-001 mounts onto a 3-row, 96-pin P2 backplane connector.
The 50-pin male connector, J2, carries the 8-bit SCSI signals from the host VMEmodules. To
run SCSI devices, you may install an additional transition module that is equipped with a SCSI
port, such as the MVME712B.
Figure 1-2
Three Row P2 Adapter
50
49
J2 2
1
J3
2
1
64
63
C1
25
1
J1
1
R1
9
C5
C6
C4
+
17
C3
C7
R2
U1
C
B
A
C2
CR1
U2
+
32
C
B
A
P1
1933 9610
This P2 adapter, and the cable for connecting to the MVME761 transition module, can be
ordered separately as model MVME761P2-001.
MVME7616E Transition Module Installation and Use (6806800A43B)
15
General Information
1.7
Five-Row P2 Adapter (MVME761-011)
Five-Row P2 Adapter (MVME761-011)
The P2 adapter for the MVME761-011 mounts onto a 5-row, 160-pin P2 backplane connector.
The 68- pin female connector, J1, carries 16-bit SCSI signals from the host VMEmodules. It also
has a 64-pin male connector, J3, for PMC I/O.
Figure 1-3
Five Row P2 Adapter
J1
1
J3
33
2
1
64
63
2
1
64
63
J5
J4
1
25
1
U1
9
C8
+
U2
17
U3
25
C9
9
R4
17
+
1
D
C
B
A
Z
CR1
32
D
C
B
A
Z
P1
1999 9701
This P2 adapter, and the cable for connecting to the MVME761 transition module, can be
ordered separately as model MVME761P2-011.
1.8
Connectors and Cables
The connectors on the MVME761 transition module and the P2 adapters are listed in the
following tables. The port connectors are located on the front panel, which is shown in Figure
1-1. See Table 1-5 on page 17 for a list of the cables. See Chapter 4, Connector Pin
Assignments.
The cable used for connecting the MVME761 transition module to the P2 adapter is provided
with the MVME761-0x1
1. You will need to purchase or fabricate the port cables.
Table 1-2 MVME761 Transition Module Connectors
16
Type
Number
Description
COM1 and
COM2
J5
J6
9-pin male DIN asynchronous serial port connector
Serial port 3
Serial port 4
J7
J8
26-pin female HD-26 synchronous serial port connector
MVME7616E Transition Module Installation and Use (6806800A43B)
Connectors and Cables
General Information
Table 1-2 MVME761 Transition Module Connectors (continued)
Type
Number
Description
Parallel port
J4
36-pin female parallel port connector
10Base-T,
100Base-TX
J9
8-pin female RJ-45 Ethernet port connector
SIM
J1, J12
60-pin female connector
VME
P2
64-pin male connector to J2 on the P2 adapter
Table 1-3 3-Row P2 Adapter Connectors (MVME761-001)
Type
Number
Description
VME
P1
96-pin female DIN 41612 connector to the chassis backplane
J3
64-pin male connector for output to P2 on the MVME761 transition module
J2
50-pin male IDC connector for internal SCSI devices
SCSI
Table 1-4 5-Row P2 Adapter Connectors (MVME761-011)
Type
Number
Description
VME
P1
160-pin female DIN 41612 connector to the chassis backplane
J4
64-pin male connector for output to P2 on the MVME761 transition
module
PMC I/O
J3
64-pin male connector for PMC I/O
SCSI
J1
68-pin female IDC connector for internal SCSI devices
Table 1-5 Transition Module Cables
Part Number
Description
Included with the
MVME761-0x1
64-line flat ribbon cable with 96-pin DIN connectors that connects P2 on
the MVME761transition module to J3 on the 3-row P2 Adapter or J4 on
the 5-row P2 adapter; 13 inches long. (30-W2799B02A).
User-supplied
EIA-232-D DTE or DCE cable (pins used depend on the processor
VMEmodule)
User-supplied
Centronics- type parallel printer cable, male-to-male
User-supplied
20-conductor cable; usually supplied with the modem
User-supplied
6-conductor cable; usually supplied with the modem
CBL761HD26DB25
Straight-through adapter cable with male HD-26 connector and female
DB-25 connector, 3 feet long. (30-NW9302B27)
If you supply your own 64-line cable to connect the P2 adapter to the MVME761 transition module, the
cable should not be longer than 1.5 feet. A longer cable is likely to cause problems, especially for the
Ethernet and parallel port signals.
MVME7616E Transition Module Installation and Use (6806800A43B)
17
General Information
1.9
Specifications
Specifications
The MVME761 transition module specifications are shown in the next table.
Table 1-6 MVME761-0x1 Specifications
Characteristics
Specifications
Power Requirements
+12 Vdc, 100 mA typical, 200 mA maximum
-12 Vdc, 100 mA (for some of the SIMs)
Operating temperature
0o to 55o C at chassis point of entry of forced air (approximately
5 CFM)
Storage temperature
-40o to +85o C
Relative Humidity
5% to 90% (non-condensing)
Board Size
(excluding front panel)
Height: 9.187 inches(233.35 mm)
Height: 3.200 inches(80.00 mm)
Thickness: 0.063 inches (1.60 mm)
1.10
Cooling Requirements
The MVME761-0x1 is tested to operate under forced air cooling with an incoming air
temperature range of 0 degrees C to 55 degrees C. Adequate cooling can be achieved with air
flowing over the module at 5 cubic feet per minute. The exact amount of airflow required for
cooling depends on the ambient air temperature and the type, number, and location of modules
and other heat sources.
1.11
FCC Compliance
The MVME761-0x1 was tested in an FCC-compliant chassis, and meets the requirements for
Class A equipment. For minimum RF emissions, it is essential that you implement the following
conditions:
18
z
Install shielded cables on all external I/O ports
z
Connect conductive chassis rails to earth ground to provide a path for connecting shields
to earth ground
z
Tighten all front panel screws
MVME7616E Transition Module Installation and Use (6806800A43B)
Hardware Preparation and Installation
2.1
2
Overview
This chapter provides unpacking instructions, hardware preparation, and installation
instructions for the MVME761 transition module, the P2 adapter, and the Serial Interface
Modules (SIMs).
2.2
Unpacking the Hardware
The MVME761 is packed in an antistatic wrapper to protect it from static discharge. Emerson
strongly recommends that you use an antistatic wrist strap and a conductive foam pad when
handling the equipment. Electronic components can be extremely sensitive to electrostatic
discharge (ESD). After removing the board from the protective wrapper, place it component
side up on a grounded, static-free surface. Do not slide the board over any surface.
Unpack the equipment from the shipping carton. Refer to the packing list and verify that all the
items are present. Save the packing material for storing and reshipping of the equipment.
2.3
Installing the Serial Interface Modules
Configure the serial ports 3 and 4 for the required interface by installing the appropriate SIM.
See Table 1-1 on page 15 for a list of the serial port interface types.
Prior to installing the SIMs, set the jumpers on header J2 (for serial port 3) and header J3 (for
serial port 4) for either DCE or DTE. Set the jumper to position:
z
1-2 if the SIM is for a DTE interface
z
2-3 if the SIM is for a DCE
Figure 2-1
1
2
DTE
Serial Port Interface Jumper Setting
3
1
2
3
DCE
MVME7616E Transition Module Installation and Use (6806800A43B)
19
Hardware Preparation and Installation
Installing the Serial Interface Modules
You must set the jumpers and install the SIMs prior to installing the MVME761 transition module
in the system chassis.The SIMs plug into connector J1 (for serial port 3) or J12 (for serial port
4) on the MVME761 transition module.
Figure 2-2
SIM Configuration
Mounting Hole
P1
Alignment
Key
Mounting Hole
11637 9610
Procedure
Install the SIMs on the MVME761 transition module per the following procedure:
1. Align the SIM so that P1 on the SIM lines up with the appropriate SIM connector (J1
for serial port 3 or J12 for serial port 4) on the transition module. Note the position
of the alignment key on P1. See Figure 2-2 on page 20.
2. Place the SIM onto the transition module SIM connector, making sure that the
mounting holes also line up with the standoffs on the transition module as shown in
Figure 2-3 on page 21.
3. Gently press the top of the SIM to seat it on the transition module SIM connector. If
the SIM does not seat with gentle pressure, re-check the alignment of the
connectors.
20
MVME7616E Transition Module Installation and Use (6806800A43B)
Installing the Serial Interface Modules
Hardware Preparation and Installation
Do not force the SIM onto the transition module.
4. Secure the SIM to the transition module standoffs with the two Phillips-head screws
provided. Do not over tighten the screws.
Figure 2-3
Installing the SIM
1911 9609
MVME7616E Transition Module Installation and Use (6806800A43B)
21
Hardware Preparation and Installation
2.4
Installing the Transition Module and P2 Adapter
Installing the Transition Module and P2 Adapter
Install the MVME761 transition module and P2 adapter in the system chassis. The P2 adapter
is required because the P2 connector on the transition module is not compatible with the P2
connector on the chassis backplane.
ESD
Use ESD
protection
Emerson strongly recommends that you use an antistatic wrist strap and a conductive
foam pad when installing or upgrading a system. Electronic components, such as disk
drives, computer boards, and memory modules, can be extremely sensitive to
electrostatic discharge (ESD). After removing the component from its protective
wrapper or from the system, place the component flat on a grounded, static-free surface
(and, in the case of a board, component side up). Do not slide the component over any
surface.
If an ESD station is not available, you can avoid damage resulting from ESD by wearing
an antistatic wrist strap (available at electronics stores) that is attached to an active
electrical ground. Note that a system chassis may not be grounded if it is unplugged.
Install the MVME761-0x1 in the system chassis according to the procedures in this chapter.
An MVME5100/MVME5500 module that is designed for use with an MVME712M
Transition Module will be damaged if you use it with an MVME761-0x1 Transition
Module.
Connecting modules while power is applied may result in damage to components on
the module.
Dangerous voltages, capable of causing death, are present in this equipment. use
extreme caution when handling, testing, and adjusting.
22
MVME7616E Transition Module Installation and Use (6806800A43B)
Installing the Transition Module and P2 Adapter
Figure 2-4
Hardware Preparation and Installation
Chassis Connections
VME BACKPLANE
Host Board
MVME761 Transition Module
P1
30-W2799B02A
64-CONDUCTOR
P2 ADAPTER
P2
P1
P2
J3 ON THE 3-ROW P2 ADAPTER
J4 ON THE 5-ROW P2 ADAPTER
ENCLOSURE BOUNDARY
11654.00 9610
Procedure
Follow these steps to configure, install, and cable the transition module.
1. Turn all equipment power OFF and disconnect the power cable from the AC power
source.
2. Remove the chassis cover per the instructions in the equipment user's manual.
3. If the chassis has a rear card cage, remove the filler panel(s) from the appropriate
card slot(s) at the rear of the chassis.
4. If necessary, move some of the other modules to allow space for the cables
connected to the P2 adapter and the transition module.
5. Install the jumper on header J1 (on the 3-row P2 adapter or header J5 on the 5-row
P2 adapter) if you are supporting SCSI devices.
6. Attach the P2 adapter, for either the 3-row or 5-row version, to the backplane
connector that is directly in line with the P2 connector on the host VMEmodule.
7. Orient pin 1 of the P2 adapter’s connector with pin 1 of the backplane connector.
MVME7616E Transition Module Installation and Use (6806800A43B)
23
Hardware Preparation and Installation
Installing the Transition Module and P2 Adapter
8. Attach the 64-conductor cable (furnished with the MVME761-0x1) to the P2 adapter
(J3 on the 3-row version, J4 on the 5-row version). Be sure to orient cable pin 1 with
connector pin 1.
9. Attach the 64-conductor cable to connector P2 on the transition module. Be sure to
orient cable pin 1 with connector pin 1.
10.Insert the transition module into the chassis slot, and tighten the attaching screws.
Make sure there is good contact with the transverse mounting rails in order to
minimize RF emissions.
11.Install the chassis cover, making sure that cables are not pinched by the cover.
12.Connect the power cable to the AC power source.
24
MVME7616E Transition Module Installation and Use (6806800A43B)
Functional Description
3.1
3
Overview
This chapter provides information on MVME761 transition module and SIM circuitry, P2 signal
multiplexing, and the configuration of the serial ports.
3.2
Circuitry
The MVME761 transition module and the Serial Interface Modules (SIMs) convert the TTL level
signals to and from the MVME5100, and MVME5500 modules to the reception and
transmission levels specified by the appropriate port interface standard.
The MVME761 transition module contains a small amount of “house keeping” circuitry. Bulk
capacitors are on the power sources (+5Vdc, +12Vdc, and -12Vdc). Pullup resistors put the
inputs to the host board in a known high even when no SIM is installed.
MVME7616E Transition Module Installation and Use (6806800A43B)
25
Functional Description
Circuitry
The block diagram for the MVME761 transition module is shown in Figure 3-1. The block
diagram for the 3-row DIN backplane P2 adapter is shown in Figure 3-2. The block diagram for
the 5-row DIN backplane P2 adapter is shown in Figure 3-3.
Figure 3-1
Transition Module Block Diagram
10Base-T
100Base-TX
Parallel
COM1
COM2
Serial 3
Serial 4
Serial Interface
Module (SIM)
Serial Interface
Module (SIM)
Buffers
EIA-232-D
P2 Multiplex Function
64-Pin DIN Connector
11638.00 9611
Figure 3-2
3-Row DIN Backplane P2 Adapter Block Diagram
8-bit Single-ended SCSI
64-pin Connector to MVME761 Transition Module
SCSI
Terminators
3-Row Backplane Connector
11639.00 961
26
MVME7616E Transition Module Installation and Use (6806800A43B)
P2 Signal Multiplexing (P2MX)
Figure 3-3
Functional Description
5-Row DIN Backplane P2 Adapter Block Diagram
16-bit Single-ended SCSI
SCSI
Terminators
64-pin Connector to MVME761 Transition Module
PMC I/O
5-Row Backplane Connector
11752.00 9703
3.3
P2 Signal Multiplexing (P2MX)
Because of a limited number of pins on the P2 connector, both the VME processor board and
the MVME761 transition module multiplex and demultiplex some of the P2 signals. This
function, called P2MX is transparent to the software and the user.
Four pins are used for the signal multiplexing:
z
MXCLK
z
MXSYNC#
z
MXDO
z
MXDI
MVME7616E Transition Module Installation and Use (6806800A43B)
27
Functional Description
P2 Signal Multiplexing (P2MX)
Sixteen time slots are defined and allocated. The signal multiplexing sequences are listed in the
following table..
Table 3-1 P2 signal multiplexing sequence
MXDO (from the MVME510x/MVME550x)
MXDI (from the MVME7616E)
Time Slot
Signal Name
Time Slot
Signal Name
0
RTS3
0
CTS3
1
DTR3
1
DSR3/MID1
2
LLB3/MODSEL
2
DCD3
3
RLB3
3
TM3/MID0
4
RTS4
4
RI3
5
DTR4
5
CTS4
6
LLB4
6
DSR4/MID3
7
RLB4
7
DCD4
8
IDREQ#
8
TM4/MID2
9
DTR1
9
RI4
10
DTR2
10
RI1
11
Reserved
11
DSR1
12
Reserved
12
DCD1
13
Reserved
13
RI2
14
Reserved
14
DSR2
15
Reserved
15
DCD2
z
MXCLK is the 10MHz bit clock for the time-multiplexed data lines, MXDO and MXDI.
z
MXSYNC# is asserted for one bit time at Time Slot 15 by the MVME5100 and MVME5500
MXSYNC# is used by the MVME761 transition module to synchronize with the VME
modules.
z
MXDO is the time-multiplexed output line from the main board and MXDI is the timemultiplexed line from the MVME761 transition module. A 16-to-1 multiplexing scheme is
used with a 10MHz bit rate.
MXSYNC# is clocked out using the falling edge of MXCLK and MDXO is clocked out with the
rising edge of the MXCLK. MXDI is sampled at the rising edge of MXCLK (the transition module
synchronizes MXDI with MXCLK’s rising edge).
28
MVME7616E Transition Module Installation and Use (6806800A43B)
Serial Interface Module Circuitry
Functional Description
The timing relationships among MXCLK, MXSYNC#, MXDO, and MXDI are illustrated in the
next figure.
Figure 3-4
Multiplex Signal Timing Chart
Time Slot 15
Time Slot 0
Time Slot 1
Time Slot 2
Time Slot 3
MXDO
Reserved
RTS3
DTR3
LLB3
RLB3
MXDI
DCD2
CTS3
DSR3
DCD3
TM3
MXCLK
MXSYNC#
11640.00 9611
3.4
Serial Interface Module Circuitry
Each Serial Interface Module has a 60-pin connector that provides all signal and power
connections to the MVME761 transition module.
TTL-level signals
All TTL-level signals, with the exception of data and clocks, are active low. The pullup resistors
on the MVME761 transition module drive all TTL inputs to the SIM to a known logic level.
SIMs
The SIMs have surge suppression circuitry for all port signals going to the external connector.
This consists of a series resistor and a dual 15V clamp diode to chassis ground. All series
resistors are 100 ohms except on the EIA-530 balanced drives, which use 10 ohm series
resistors.
EIA-232-D SIMs employ MC145406 ICs as line transmitters to convert the TTL output signals
from the host VMEmodule to EIA-232-D voltage levels. As line receivers, the MC145406 ICs
convert the EIA-232-D input signals to TTL voltage levels which are sent to the VME module.
The MC145406 transceiver IC requires a series diode on the +12V supply and a clamp diode
to logic ground on the -12V supply. The diodes are located on the transition module rather than
on the SIM due to space limitations.
For all port interfaces, the SIMs support the transmitter signal element timing as either input or
output signals.
MVME7616E Transition Module Installation and Use (6806800A43B)
29
Functional Description
3.5
COM1 and COM2 Asynchronous Serial Ports
COM1 and COM2 Asynchronous Serial Ports
The asynchronous serial port (COM1 and COM2) configuration is shown in the next figures..
Figure 3-5
EIA-574 DTE Port Configuration
DB9
TXD
SOUT1
3
RTS
RTS1#
7
DTR
DTR1#
4
RXD
SIN1
2
COM1
CTS
CTS1#
8
DSR
6
DSR1#
DCD
DCD1#
RI
RI1#
1
9
GND
5
PC87308
P2/P2MX
DB9
TXD
SOUT2
3
RTS
RTS2#
7
DTR
DTR2#
4
RXD
SIN2
2
CTS
CTS2#
COM2
8
DSR
DSR2#
6
DCD
DCD2#
1
RI
RI2#
9
GND
5
VME Module
30
MVME761
Transition Module
MVME7616E Transition Module Installation and Use (6806800A43B)
Asynchronous/Synchronous Serial Ports
3.6
Functional Description
Asynchronous/Synchronous Serial Ports
The asynchronous/synchronous serial port (Port 3 and Port 4) interface configuration diagrams
are on the following pages.
Figure 3-6
EIA232-DCE Copnfirguration Port 3
MVME761
VME MODULE
Z85230 SCC
EIA232-DCE SIM
HD26
TXD
3
RTS#
5
RXD
2
CTS#
4
DCD#
20
J18
TRXC
J2
3
2
3
2
1
1
15
17
24
RTXC
P2/P2MX
DCE
Z8536 CIO
DTR#
8
LLB#
25
RLB#
22
DSR#
6
RI#
21
TM#
18
7
Header J18 1-2
MVME7616E Transition Module Installation and Use (6806800A43B)
Header J2 2-3
31
Functional Description
Asynchronous/Synchronous Serial Ports
Figure 3-7
EIA232-DCE Configuration Port 4
VME MODULE
MVME761
Z85230 SCC
EIA232-DCE SIM
HD26
TXD
3
RTS#
5
RXD
2
CTS#
4
DCD#
20
J17
J19
J3
1
2
3
2
3
1
15
17
J16
TRXC
1
2
RTXC
3
24
P2/P2MX
DCE
Z8536 CIO
DTR#
8
LLB#
25
RLB#
22
DSR#
6
RI#
21
TM#
18
7
Headers: J16 2-3
J17 1-2
J19 1-2
32
Header J3 2-3
MVME7616E Transition Module Installation and Use (6806800A43B)
Asynchronous/Synchronous Serial Ports
Figure 3-8
Functional Description
EIA232-DTE Configuration Port 3
VME MODULE
MVME761
Z85230 SCC
EIA232-DTE SIM
HD26
TXD
2
RTS#
4
RXD
3
CTS#
5
DCD#
8
J18
TRXC
J2
3
2
3
1
1
24
2
15
17
RTXC
P2/P2MX
DTE
Z8536 CIO
DTR#
20
LLB#
18
RLB#
21
DSR#
6
RI#
22
TM#
25
7
Header J18 2-3
MVME7616E Transition Module Installation and Use (6806800A43B)
Header J2 1-2
33
Functional Description
Figure 3-9
Asynchronous/Synchronous Serial Ports
EIA232-DTE Configuration Port 4
MVME761
VME MODULE
Z85230 SCC
EIA232-DTE SIM
HD26
TXD
2
RTS#
4
RXD
3
CTS#
5
DCD#
8
J17
J19
J3
1
2
3
3
1
24
2
15
J16
TRXC
1
2
RTXC
3
17
P2/P2MX
DTE
Z8536 CIO
DTR#
20
LLB#
18
RLB#
21
DSR#
6
RI#
22
TM#
25
7
Headers: J16 2-3
J17 2-3
J19 1 2
34
Header J3 1-2
MVME7616E Transition Module Installation and Use (6806800A43B)
Connector Pin Assignments
4.1
4
Overview
This chapter provides the pin assignments for the P2 connector and front panel port connectors
on the MVME761 transition module, as well as for the SCSI and PMC I/O connectors on the P2
adapters.
4.2
P2 Connector
Signaling and power from the host VMEmodules are received through connector P2, a 64-pin
DIN connector. Because the P2 adapter reroutes some of the signals, connector P2 on the
MVME761 transition module is not pin-for-pin compatible with connector P2 on the host
VMEmodules.
The pin assignments and signal mnemonics for the MVME761 transition module P2 connector
are listed in the following table.
Table 4-1 P2 Connector Pin Assignments
Row A Pins
Row C Pins
Pin
Signal
Pin
Signal
1
C- (R- for RJ-45 J9)
1
C+ (R+ for RJ-45 J9)
2
T-
2
T+
3
R-
3
R+
4
+12VF
4
PRSTB#
5
GND
5
PRD0
6
PRD1
6
PRD2
7
PRD3
7
PRD4
8
PRD5
8
PRD6
9
PRD7
9
GND
10
PRACK#
10
GND
11
PRBSY
11
PRPE
12
PRSEL
12
INPRIME#
13
PRFAULT#
13
GND
14
AUTOFD#
14
GND
15
SELIN#
15
GND
16
TXD3
16
RXD3
17
RTXC3
17
TRXC3
MVME7616E Transition Module Installation and Use (6806800A43B)
35
Connector Pin Assignments
Asynchronous Serial Port Connectors (J5/J6)
Table 4-1 P2 Connector Pin Assignments (continued)
Row A Pins
4.3
Row C Pins
Pin
Signal
Pin
Signal
18
GND
18
TXD1_232
19
GND
19
RXD1_232
20
GND
20
RTS1_232
21
CTS1
21
GND
22
TXD4
22
GND
23
RXD4
23
GND
24
RTXC4
24
GND
25
TRXC4
25
GND
26
No Connect
26
-12VF
27
MSYNC#
27
GND
28
MCLK
28
GND
29
TXD2_232
29
GND
30
RXD2_232
30
GND
31
RTS2_232
31
CTS2_232
32
MDO
32
MDI
Asynchronous Serial Port Connectors (J5/J6)
The interface for the asynchronous serial ports, COM1 and COM2, is provided with two
standard DB9 connectors, J5 and J6. The connector shields for these ports are tied to chassis
ground. The pin assignments and signal mnemonics for these connectors are listed in Table
4-2.
Table 4-2 COM1 and COM2 Pin Assignments
36
Pin
Signal
1
DCD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI
MVME7616E Transition Module Installation and Use (6806800A43B)
Asynchronous/Synchronous serial Port connectors (J7/J8)
4.4
Connector Pin Assignments
Asynchronous/Synchronous serial Port
connectors (J7/J8)
The interface for the asynchronous/synchronous serial ports 3 and 4 is provided by two HD-26
connectors, J7 and J8. The connector shields for these ports are tied to chassis ground.
The pin assignments and signal mnemonics for serial ports 3 and 4 are listed in the following
tables.
Table 4-3 Serial Port 3 Pin Assignments
Pin
Signal
Pin
Signal
1
No Connect
14
SP3_P14
2
TXD3
15
TXCI3
3
RXD3
16
SP3_P16
4
RTS3
17
RXCI3
5
CTS3
18
LLB3
6
DSR3
19
SP3_P19
7
GND
20
DTR3
8
DCD3
21
RLB3
9
SP3_P9
22
RI3
10
SP3_P10
23
SP3_P23
11
SP3_P11
24
TXCO3
12
SP3_P12
25
TM3
13
SP3_P13
26
No Connect
Table 4-4 Serial Port 4 Pin Assignments
Pin
Signal
Pin
Signal
1
No Connect
14
SP4_P14
2
TXD4
15
TXCI4
3
RXD4
16
SP4_P16
4
RTS4
17
RXCI4
5
CTS4
18
LLB4
6
DSR4
19
SP4_P19
7
GND
20
DTR4
8
DCD4
21
RLB4
9
SP4_P9
22
RI4
10
SP4_P10
23
SP4_P23
11
SP4_P11
24
TXCO4
12
SP4_P12
25
TM4
MVME7616E Transition Module Installation and Use (6806800A43B)
37
Connector Pin Assignments
Parallel I/O Port Connector (J4)
Table 4-4 Serial Port 4 Pin Assignments (continued)
4.5
Pin
Signal
Pin
Signal
13
SP4_P13
26
No Connect
Parallel I/O Port Connector (J4)
The interface for the parallel port is a standard IEEE P1284-C, 36-pin connector, J4. The
functionality of each signal depends on the mode of operation of this bidirectional Parallel
Peripheral Interface. Refer to the IEEE P1284 D2.00 Standard for a complete description of
each signal function. The connector shield is tied to chassis ground.
The pin assignments and signal mnemonics for this connector are listed in Table 4-5.
Table 4-5 Parallel I/O Connector Pin Assignments
38
Pin
Signal
Signal
Pin
1
PRBSY
GND
19
2
PRSEL
GND
20
3
PRACK_
GND
21
4
PRFAULT_
GND
22
5
PRPE
GND
23
6
PRD0
GND
24
7
PRD1
GND
25
8
PRD2
GND
26
9
PRD3
GND
27
10
PRD4
GND
28
11
PRD5
GND
29
12
PRD6
GND
30
13
PRD7
GND
31
14
INPRIME_
GND
32
15
PRSTB_
GND
33
16
SELIN_
GND
34
17
AUTOFD_
GND
35
18
Pull-up
No Connect
36
MVME7616E Transition Module Installation and Use (6806800A43B)
Ethernet Connector (J9)
4.6
Connector Pin Assignments
Ethernet Connector (J9)
The 10Base-T/100Base-TX Ethernet interface is a RJ-45 connector, J9. The connector shield
is tied to chassis ground. The pin assignments and signal mnemonics for this connector are
listed in Table 4-6.
Table 4-6 10Base-T/100Base-TX Pin Assignments
Pin
Signal
1
TD+
2
TD-
3
RD+
4
Terminated
5
Terminated
6
RD-
7
Terminated
8
Terminated
4.7
P2 Adapter Connectors
4.7.1
3-Row P2 Adapter (J2)
The 8-bit SCSI connector on the 3-row DIN backplane P2 Adapter is a 50-pin connector, J2.
The pin assignments and signal mnemonics for this connector are listed in Table 4-7.
Table 4-7 8-bit SCSI Connector (3-Row P2 adapter)
Pin
Signal
Signal
Pin
1
GND
TERMPWR
26
2
SDB0
GND
27
3
GND
GND
28
4
SDB1
GND
29
5
GND
GND
30
6
SDB2
GND
31
7
GND
ATN
32
8
SDB3
GND
33
9
GND
GND
34
10
SDB4
GND
35
11
GND
BSY
36
12
SDB5
GND
37
MVME7616E Transition Module Installation and Use (6806800A43B)
39
Connector Pin Assignments
3-Row P2 Adapter (J3)
Table 4-7 8-bit SCSI Connector (3-Row P2 adapter) (continued)
4.7.2
Pin
Signal
Signal
Pin
13
GND
ACK
38
14
SDB6
GND
39
15
GND
RST
40
16
SDB7
GND
41
17
GND
MSG
42
18
DBP
GND
43
19
GND
SEL
44
20
GND
GND
45
21
GND
D/C
46
22
GND
GND
47
23
GND
REQ
48
24
GND
GND
49
25
No Connect
O/I
50
3-Row P2 Adapter (J3)
The pin assignments and signal mnemonics for this connector are listed in Table 4-8.
Table 4-8 VME Connector (3-Row P2 adapter)
40
Pin
Signal
Signal
Pin
1
C+
DCD3
33
2
C-
DTR3
34
3
T+
TXD1
35
4
T-
GND
36
5
R+
RXD1
37
6
R-
GND
38
7
PRSTB_L
RTS1
39
8
+12VF
GND
40
9
PRD0
GND
41
10
GND
CTS1
42
11
PRD2
GND
43
12
PRD1
TXD4
44
13
PRD4
GND
45
14
PRD3
RXD4
46
15
PRD6
GND
47
16
PRD5
RTS4
48
MVME7616E Transition Module Installation and Use (6806800A43B)
5-Row P2 adapter (J1)
Connector Pin Assignments
Table 4-8 VME Connector (3-Row P2 adapter) (continued)
4.7.3
Pin
Signal
Signal
Pin
17
GND
GND
49
18
PRD7
TRXC4
50
19
GND
DTR4
51
20
PRACK_L
CTS4
52
21
PRPE
GND
53
22
PRBSY
DCD4
54
23
PRINIT_L
GND
55
24
PRSEL
RTXC4
56
25
GND
GND
57
26
PRFAULT_L
TXD2
58
27
GND
GND
59
28
TXD3
RXD2
60
29
GND
CTS2
61
30
RXD3
RTS2
62
31
CTS3
DCD2
63
32
RTS3
DTR2
64
5-Row P2 adapter (J1)
The 16-bit SCSI connector on the 5-row DIN backplane P2 Adapter is a 68-pin connector, J1.
The pin assignments and signal mnemonics for this connector are listed in Table 4-9.
Table 4-9 16-bit SCSI Connector (5-Row P2 adapter)
Pin
Signal
Signal
Pin
1
GND
SDB12
35
2
GND
SDB13
36
3
GND
SDB14
37
4
GND
SDB15
38
5
GND
DBP1
39
6
GND
SDB0
40
7
GND
SDB1
41
8
GND
SDB2
42
9
GND
SDB3
43
10
GND
SDB4
44
11
GND
SDB5
45
12
GND
SDB6
46
MVME7616E Transition Module Installation and Use (6806800A43B)
41
Connector Pin Assignments
PMC I/O, 5-Row P2 Adapter (J3)
Table 4-9 16-bit SCSI Connector (5-Row P2 adapter) (continued)
4.7.4
Pin
Signal
Signal
Pin
13
GND
SDB7
47
14
GND
DBP0
48
15
GND
GND
49
16
GND
GND
50
17
TERMPWR
TERMPWR
51
18
TERMPWR
TERMPWR
52
19
No Connect
No Connect
53
20
GND
GND
54
21
GND
ATN
55
22
GND
GND
56
23
GND
BSY
57
24
GND
ACK
58
25
GND
RST
59
26
GND
MSG
60
27
GND
SEL
61
28
GND
D/C
62
29
GND
REQ
63
30
GND
O/I
64
31
GND
SDB8
65
32
GND
SDB9
66
33
GND
SDB10
67
34
GND
SDB11
68
PMC I/O, 5-Row P2 Adapter (J3)
The PMC I/O connector on the 5-row DIN backplane P2 Adapter is a 64-pin connector, J3. The
pin assignments and signal mnemonics for this connector are listed in Table 4-10.
Table 4-10 PMC I/O Connector (5-Row P2 adapter)
42
Pin
Signal
Signal
Pin
1
GND
GND
33
2
PMCIO0
PMCIO16
34
3
GND
GND
35
4
PMCIO1
PMCIO17
36
5
GND
GND
37
6
PMCIO2
PMCIO18
38
MVME7616E Transition Module Installation and Use (6806800A43B)
5-Row P2 adapter (J4)
Connector Pin Assignments
Table 4-10 PMC I/O Connector (5-Row P2 adapter) (continued)
4.7.5
Pin
Signal
Signal
Pin
7
GND
GND
39
8
PMCIO3
PMCIO19
40
9
GND
GND
41
10
PMCIO4
PMCIO20
42
11
GND
GND
43
12
PMCIO5
PMCIO21
44
13
GND
GND
45
14
PMCIO6
PMCIO22
46
15
GND
GND
47
16
PMCIO7
PMCIO23
48
17
GND
GND
49
18
PMCIO8
PMCIO24
50
19
GND
GND
51
20
PMCIO9
PMCIO25
52
21
GND
GND
53
22
PMCIO10
PMCIO26
54
23
GND
GND
55
24
PMCIO11
PMCIO27
56
25
GND
GND
57
26
PMCIO12
PMCIO28
58
27
GND
GND
59
28
PMCIO13
PMCIO29
60
29
GND
GND
61
30
PMCIO14
PMCIO30
62
31
GND
GND
63
32
PMCIO15
PMCIO31
64
5-Row P2 adapter (J4)
The J4 connector on the 5-row P2 adapter is a VME, 64-pin male connector used for output to
the P2 connector on the MVME761.
Table 4-11 VME Connector (3-Row P2 adapter)
Pin
Signal
Signal
Pin
1
C+
DCD3
33
2
C-
DTR3
34
MVME7616E Transition Module Installation and Use (6806800A43B)
43
Connector Pin Assignments
5-Row P2 adapter (J4)
Table 4-11 VME Connector (3-Row P2 adapter) (continued)
44
Pin
Signal
Signal
Pin
3
T+
TXD1
35
4
T-
GND
36
5
R+
RXD1
37
6
R-
GND
38
7
PRSTB_L
RTS1
39
8
+12VF
GND
40
9
PRD0
GND
41
10
GND
CTS1
42
11
PRD2
GND
43
12
PRD1
TXD4
44
13
PRD4
GND
45
14
PRD3
RXD4
46
15
PRD6
GND
47
16
PRD5
RTS4
48
17
GND
GND
49
18
PRD7
TRXC4
50
19
GND
DTR4
51
20
PRACK_L
CTS4
52
21
PRPE
GND
53
22
PRBSY
DCD4
54
23
PRINIT_L
GND
55
24
PRSEL
RTXC4
56
25
GND
GND
57
26
PRFAULT_L
TXD2
58
27
GND
GND
59
28
TXD3
RXD2
60
29
GND
CTS2
61
30
RXD3
RTS2
62
31
CTS3
DCD2
63
32
RTS3
DTR2
64
MVME7616E Transition Module Installation and Use (6806800A43B)
Index
Numerics
100Base-TX 13, 39
10Base-T 13, 39
A
asynchronous serial port
signals 36
asynchronous/synchronous serial port
configurations 31
signals 37
B
backplane connector 15, 16
C
cables
64-line flat ribbon 17
EIA-232 17
modem 17
P2 adapter 15
printer 17
shielded 18
circuitry
MVME761 25
SIMs 29
Class A equipment 18
COM1/COM2 pin assignments 36
connectors 16
MVME761
J4, parallel port 38
J5/J6, serial ports 36
J7/J8, serial ports 37
J9, Ethernet 39
P2 35
RJ-45 39
P2 adapter 3-row
J2, SCSI connector 39
J3, VME 40
P2 adapter 5-row
J1, SCSI 41
J3, PMC I/O 42
J4, VME 43
SIM 29
cooling requirements 18
D
DIN connector 35
E
EIA-232-D, circuitry 29
EMI,ESD 13
ESD precautions 22
Ethernet 13
Ethernet pin assignments 39
Ethernet signals 39
F
FCC compliance 18
features 13
G
grounding 18
I
I/O controllers 13
installation
MVME761 22
P2 adapter 22
SIMs 19
J
jumper settings, SCSI devices 23
L
line transmitters 29
M
model numbers 9
multiplexing function 13
MVME761
board size 18
cables 17
circuitry 25
connectors 16, 35
description 13
installation 22
pin assignments (P2) 35
specifications 18
O
operating temperature 18
output to P2 connector (MVME761) 40, 43
P
P2 Adapter 13
P2 adapter connectors 39
P2 adapter, 3-row 15
P2 adapter, 5-row 16
P2 adapter, connectors 16
P2 adapter, installation 22
P2 adapter, pin assignments 39
parallel port pin assignments 38
MVME7616E Transition Module Installation and Use (6806800A43B)
45
parallel port signals 38
part numbers
P2 adapter, 3-row 15
P2 adapter, 5-row 16
SIM 14
pin assignments 35
Ethernet connector J9 39
P2 connector (MVME761) 35
parallel port J4 (MVME761) 38
PMC I/O, J3 (P2 adapter 5-row) 42
SCSI connector J2 (P2 adapter 3-row) 39
SCSI, J1 (P2 adapter 5-row) 41
serial port (MVME761) 36
serial port 3/4 (MVME761) 37
VME connector J4 (P2 adapter 5-row) 43
VME connector, J3 (P2 adapter 3-row) 40
pin compatibility for P2 connectors 35
PMC I/O 16
PMC I/O connector (P2 adapter 5-row) 42
port configurations 30
port connectors, location 16
port interfaces 14
port signals 36, 38
power requirements 18
power source 25
procedures
cabling the transition module 24
installing SIMs 20
product description 9, 13
R
relative humidity 18
RF emissions 18
running SCSI devices 15
46
S
SCSI connector 41
SCSI connector pin assignments 39, 41
SCSI connector, 3-row (P2 adapter) 39
SCSI connector, 5-row (P2 adapter) 41
SCSI devices 15
SCSI port 15
Serial Interface Module, see SIM
serial port
configurations 30, 31–??
signals 36
serial port 3 pin assignments 37
serial port 4 pin assignments 37
serial ports 13, 14, 25
series resistors 29
signal multiplexing 25
signals, TTL-level 29
SIM 13
circuitry 25, 29
description 14
installation 19
part numbers 14
specifications 18
storage temperature 18
surge suppression 29
T
temperature 18
TTL-level signals 29
V
variants 9
VMEmodules, supported 13
MVME7616E Transition Module Installation and Use (6806800A43B)