advertisement
Table of Contents
Windows Vista / Windows 7 ...................................................................... 12
http://www.sapido.com.tw/
2
User Manual v1. 0.0
http://www.sapido.com.tw/
3
User Manual v1. 0.0
Wan Type Auto Detection.......................................................................... 92
http://www.sapido.com.tw/
4
User Manual v1. 0.0
Communications Regulation Information ....................................................... 102
http://www.sapido.com.tw/
5
User Manual v1. 0.0
FCC Caution
FCC Part 15.19 Caution:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation
2. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
3. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Statement in User’s Manual (for calss B)
FCC Section 15.105
“Federal Communications Commission (FCC) Statement”
This equipment has been tested and found to comply with the limits for a lass B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver. http://www.sapido.com.tw/
6
User Manual v1. 0.0
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
CE Statement of Conformity
Our product has been tested in typical configuration by Ecom Sertech Corp and was found to comply with the essential requirement of “Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility” (89/336/EEC; 92/31/EEC;
93/68/EEC) http://www.sapido.com.tw/
7
User Manual v1. 0.0
Chapter 1 Introduction
1.1 Product Appearance
LED Indicator Status Description:
LED Function
Power indication
System status
&
WPS status
Wire less activity
WAN port activity
LAN port activity
Color Status
Green
Description
On Power is being applied to this product
On System is ready to work
Green
Blin king
Reset / Firmware update in progress
120ms
WPS function in progress
On Wire less is active
Green
Blin king
Wire less Tx/ Rx activity
30ms
On 1000Mbps Ethernet is connected
Green
Blin king
1000Mbps Ethernet Tx/Rx activ ity
30ms
On 10/ 100Mbps Ethernet is connected
Green
Blin king
10/ 100Mbps Ethernet Tx/Rx act ivity
120ms
On 1000Mbps Ethernet is connected
Green
Blin king
1000Mbps Ethernet Tx/Rx activ ity
30ms
On 10/ 100Mbps Ethernet is connected
Green
Blin king
10/ 100Mbps Ethernet Tx/Rx act ivity
120ms http://www.sapido.com.tw/
8
User Manual v1. 0.0
Chapter 2 System and Network Setup
The GR297n provides many Internet connecting ways, including Gigabit Ethernet and
802.11n Wi-Fi / 3.5G , to meet different users’ need. GR297n has intelligent Plug-n-Play and can detect user’s environment to make connecting Internet more easily..
GR297n has firewall and WEP/WPA/WPS to make the network environment more secure when many devices are sharing bandwidth. It is designed for home user and business user and is a secure, reliable, easy-to-use network solution.
GR297n has Green AP function. When it is standby, system will save power. It also supports
IEEE 802.3az standard and saving 80% power in Ethernet part
High Power WiFi
By increasing the transmission power of WiFi, the wireless WiFi has a wider coverage than the average and better connection quality.
Green AP Power-saving function
When Wireless and CPU are full loading, the output power of wireless and CPU will reach maximum. When Wireless and CPU are standby, system will decrease the output power of wireless and CPU. System will enable this function automatically without any setup by user.
This function will decrease the temperature and enlarge the battery life.
IEEE 802.3az supported
First, it detects link status, allowing each port on the switch to power down into a standby or
‘sleep’ mode when a connected device, such as a computer, is not active. Second, it detects cable length and adjusts the power accordingly.
USB File Sharing
GR297n has 2 USB 2.0 port to connect external hard disk or flash driver. User can easily share files through the built-in Samba Server functionality.
Gigabit Ethernet
GR297n has Gigabit Ethernet and is 10X faster than normal Ethernet.
2.1 Build Network Connection
Administrator can manage the settings for WAN, LAN, Wireless Network, NTP, password,
VPN, Firewall, etc. http://www.sapido.com.tw/
9
User Manual v1. 0.0
Please confirm the network environment or the purpose before setting this product.
2.2 Connecting
GR297N
Prepare the followings before the connection:
PC or Notebook for setup
Ethernet cable
1. Make sure you are under “Router Mode”.
2. Connect GR297N to xDSL/ Cable modem with the Ethernet cable, WAN to LAN.
3. Turn on your Computer.
2.3 Network setup
After the network connection is built, the next step is setup the router with proper network parameters, so it can work properly in your network environment. Before you connect to the wireless router and start configuration procedures, your computer must be able to get an IP address from the wireless router automatically (use dynamic IP address). If it’s set to use static IP address, or you’re unsure, please follow the below instructions to configure your computer with dynamic IP address:
If the operating system of your computer is….
Windows 2000 - please go to section 2.3.1
Windows XP - please go to section 2.3.2
Windows Vista/Win7 - please go to section 2.3.3
2.3.1 Windows 2000
http://www.sapido.com.tw/
10
User Manual v1. 0.0
Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Dial-up Connections icon, double click Local Area
Connection, and Local Area Connection Properties window will appear. Select “Internet
Protocol (TCP/IP)”, then click “Properties”.
1. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”.
2.3.2 Windows XP
1. Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Internet Connections icon, click Network http://www.sapido.com.tw/
11
User Manual v1. 0.0
Connections, then double-click Local Area Connection, Local Area Connection Status window will appear, and then click “Properties”.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”.
2.3.3 Windows Vista / Windows 7
http://www.sapido.com.tw/
12
User Manual v1. 0.0
1. Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Click View Network Status and Tasks, and then click Manage Network
Connections. Right-click Local Area Network, then select “Properties”. Local Area
Connection Properties window will appear, select “Internet Protocol Version 4 (TCP / IPv4)”, and then click “Properties”.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. http://www.sapido.com.tw/
13
User Manual v1. 0.0
2.4 Router IP Address Lookup
After the IP address setup was completed, please clicks “start” → “run” at the bottom-lower corner of your desktop:
Input “cmd”, and then click “OK”.
Input “ipconfig”, then press “Enter” key. Please check the IP address followed by “Default
Gateway” (In this example, the gateway IP address of router is 192.168.1.1) http://www.sapido.com.tw/
14
User Manual v1. 0.0
NOTE: If the IP address of Gateway is not displayed, or the address followed by ‘IP Address’ begins with
“169.x.x.x”, please recheck network connection between your computer and router, and / or go to the beginning of this chapter, to recheck every step of network setup procedure.
2.4.1 Log into Web GUI
After your computer obtained an IP address from wireless router, please start your web browser, and input the IP address of the wireless router in address bar, and the following message should be shown. Please click “admin” to login the GR297N .
Enter the User name and Password in to the blank and then Click
Login
. The default values for User Name and Password are
admin
(all in lowercase letters).
Users can set or change user name and password used for accessing the web management interface in this section. http://www.sapido.com.tw/
15
User Manual v1. 0.0
Input User Name and New Password, then input Confirm Password again.
Chapter 3 Internet Connection
This Chapter describes how to setup GR297N to the internet. The GR297N is delivered with the following factory default parameters.
Default IP address: 192.168.1.1
Default IP subnet mask: 255.255.255.0
Web login user name: admin
Web login password: admin
3.1 Using as a broadband router
Open a Web browser, and enter http://192.168.1.1
(Default Gateway) into the blank. http://www.sapido.com.tw/
16
User Manual v1. 0.0
Enter the User name and Password into the blank and then click
Login
. The default values for User Name and Password are
admin
(all in lowercase letters).
Download pdadd
Status page
Logout
3.2 Home button menu
Click Home button icon to enter MENU as below.
http://www.sapido.com.tw/
17
User Manual v1. 0.0
Item
Internet Setup
A
P
WiFi AP
Firmware Upgrade
Parental control
Office Control
File Menu
Webcam server
VPN Server
http://www.sapido.com.tw/
Description
There are several different method to access Internet
,
PPPoE
、
DHCP
、
Static IP
、
PP TP
、
L2TP
、
WiFi ISP
If a router is already set at the house, and you want to make the wireless LAN communication
When you connect to the internet wirelessly through PC and wireless device without wireless LAN function equipped.
This function allows you upgrade the GR297N firmware to new version. Please note do not power off the devic e during the upload because it may crash the system.
You can use URL filter
、
MAC Filter Schedule and Wireless
Schedule to limit access Internet.
For office environment
, there are Multiple AP
、
Wireless Access
Cont rol
、
IP Filtering
、
IP Binding and QoS
There are Samba Storage and FTP server features
For image record
PPTP/L2TP
general setup introduction.
18
User Manual v1. 0.0
DoS
Remote management
Advance Setup
Status
Factory Default
Reboot
Logout
Denial of Service
This page allow you to access the GUI on WAN.
Advance setting menu
You could check WAN, LAN, Client net work in status.
You could reset the current configuration to factory default.
This function is used to reboot
This page is used to logout. http://www.sapido.com.tw/
19
User Manual v1. 0.0
3.3 Internet Setup
Click
Internet Setup
icon to enter WAN setup as below
.
The Internet Setup is depended on the service that you contract with the provider. The GR297N provides five selections for the Internet Mode type,
PPPoE, DHCP, Static IP ,
PPTP and L2TP
、
WiFi ISP
、
3.5G
、
Smart Phone
、
LTE.
Check with your ISP if you don’t know the WAN type.
.
http://www.sapido.com.tw/
20
User Manual v1. 0.0
3.3.1 PPPoE
Item
User Name
Password
Wireless AP
SSID
Encryption
3.3.2 DHCP
Description
Input your us er name provided by your ISP. If you don’t know, please check with your ISP.
Input the password provided by your ISP.
Turn on/ off wireless
Service S et identifier, users can define to any or keep as default.
Select wireless encryption type form the drop-down list. http://www.sapido.com.tw/
21
User Manual v1. 0.0
Item
MAC type
Wireless AP
SSID
Encryption
Description
Select
"Universal” or “Specific"
Universal
: clone controller PC mac address as GR297n WAN mac address
Specific
: use GR297n itself mac address
Turn on/ off wireless
Service S et identifier, users can define to any or keep as default.
Select wireless encryption type form the drop-down list. http://www.sapido.com.tw/
22
User Manual v1. 0.0
3.3.3 Static IP
Item
IP Address
Subnet Mask
Gateway
DNS
Wireless AP
SSID
Encryption
3.3.4 PPTP
Description
Enter the IP address which is provided by your ISP.
Please enter the Subnet Mask address
Input ISP Default Gateway Address.
Input DNS information which is provided by your ISP
Turn on/ off wireless
Service S et identifier, users can define to any or keep as default.
Select wireless encryption type form the drop-down list. http://www.sapido.com.tw/
23
User Manual v1. 0.0
Item
Addre ss Mode
IP Address
Gateway
Server IP Address
Description
Select
"Dynamic"
or
"Static"
Input your IP address or domain name
Input ISP Default Gateway Address.
Input your server IP address provided by your ISP. If you don’t know, please check with your ISP.
Input PPTP account provided by your ISP.
User Name
Password
MTU Size
Input the password provided by your ISP.
Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
Enable MPPE Encryption
Microsoft Point-t o-Point Encryption (MPPE ) provides data security for the PPTP connection that is between the VPN client and VPN server.
Enable MPPC Compre ssion
Microsoft Point-to-Point Compression (MPPC) is a scheme used to compress Point-t o-Point Protocol (PPP) packets between Cisco and Microsoft client devices. The MPPC algorit hm is designed to optimize bandwidth utilization in order to support multiple simultaneous connections. The MPP C algorithm us es a
Lempel-Ziv (LZ) based algorithm with a continuous history buffer, called a dictionary
Wireless AP
Turn on/ off wireless
SSID
Service S et identifier, users can define to any or keep as default. http://www.sapido.com.tw/
24
User Manual v1. 0.0
Encryption
3.3.5 L2TP
Select wireless encryption type form the drop-down list.
Item
Addre ss Mode
IP Address
Gateway
Server IP Address
User Name
Password
MTU Size
Wireless AP
SSID
Encryption
http://www.sapido.com.tw/
Description
Select
"Dynamic"
or
"Static"
Input your IP address or domain name
Input ISP Default Gateway Address.
Input your server IP address provided by your ISP. If you don’t know, please check with your ISP.
Input PPTP account provided by your ISP.
Input the password provided by your ISP.
Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
Turn on/ off wireless
Service S et identifier, users can define to any or keep as default.
Select wireless encryption type form the drop-down list.
25
User Manual v1. 0.0
3.3.6 WiFi ISP
GR297n WAN get IP address from other wireless AP and LAN/Wireless LAN client get IP from GR297n.
Item
Survey
Pre-Shared Key
Extend SSID
Encryption
3.3.7 3.5G
Description
List all available wireless AP
Input the wireless AP key which you want to connect
Provide SSID for wireless client which want to connect to GR297n
Select wireless encryption type form the drop-down list. http://www.sapido.com.tw/
26
User Manual v1. 0.0
Item
Mode
Network Traffic Moni tor
Limit Internet Traffic
Connection Speed
SIM PIN
Authenti cation
Wireless AP
SSID
Encryption
3.3.8 Smartphone
Description
Input your us er name provided by your ISP. If you don’t know, please check with your ISP.
BRC70n will record 3.5G traffic usage volume
User can limit 3.5G traffic usage volume to prevent over budget
Provide 3 kinds of speed
, auto is recommended
SIM card P IN number
Provide 3 kinds of authentication methods
, auto is recommended
Turn on/ off wireless function
Service S et identifier, users can define to any or keep as default.
Select wireless encryption type form the drop-down list. http://www.sapido.com.tw/
27
User Manual v1. 0.0
Item
Service
Region
ISP
APN
User Name
Password
Phone number
Authenti cation
Wireless AP
SSID
Encryption
http://www.sapido.com.tw/
Description
GR297n support 4 kinds of smart phon e , Nokia 、 Black Berry 、
Samsung 、 iPhone and Andriod phone
iPhone do not need to do any setting
,
all you need is to turn on iphone hotspot function and connect it to GR297n USB port
Select correct phone service region
Select correct phone service ISP
Please check 3.5G ISP to get APN data
Please check 3.5G ISP to get user name
Please check 3.5G ISP to get password
Please check 3.5G ISP to number data
Provide 3 kinds of authentication methods
, auto is recommended
Turn on/ off wireless function
Service S et identifier, users can define to any or keep as default.
Select wireless encryption type form the drop-down list.
28
User Manual v1. 0.0
3.3.9 LTE
Item
Mode
Network Traffic Moni tor
Limit Internet Traffic
Connection Speed
SIM PIN
Authenti cation
Wireless AP
SSID
Encryption
Description
Input your us er name provided by your ISP. If you don’t know, please check with your ISP.
BRC70n will record 3.5G traffic usage volume
User can limit 3.5G traffic usage volume to prevent over budget
Provide 3 kinds of speed
, auto is recommended
SIM card P IN number
Provide 3 kinds of authentication methods
, auto is recommended
Turn on/ off wireless function
Service S et identifier, users can define to any or keep as default.
Select wireless encryption type form the drop-down list.
3.4 A
P
If a router is already set at the house, and you want to make the wireless LAN communication.
This mode does not support
WAN
、
DHCP
、
NAT
、
DDNS
、
QoS
、
Firewall
、 http://www.sapido.com.tw/
29
User Manual v1. 0.0
Static/Dynamic route
、
VPN Server features.
Item
Wireless AP
SSID
Encryption
Wireless AP
Description
Turn on/ off wireless
Service S et identifier, users can define to any or keep as default.
Select wireless encryption type form the drop-down list.
Turn on/ off wireless
3.5 WiFi AP
When you connect to the internet wirelessly through PC and wireless device without wireless LAN function equipped. This mode does not support
WAN
、
DHCP
、
NAT
、
DDNS
、
QoS
、
Firewall
、
Static/Dynamic route
、
VPN Server features.
http://www.sapido.com.tw/
30
User Manual v1. 0.0
http://www.sapido.com.tw/
31
User Manual v1. 0.0
Chapter 4 GUI Function Setup
4.1 Firmware Upgrade
This function can upgrade the firmware of the router. There are two methods for user upgrade firmware: Auto upgrade and Manual upgrade.
Caution: To prevent that firmware upgrading is interrupted by other wireless signals and causes failure.
We recommend users to use wired connection during upgrading.
Note : The firmware upgrade will not remove your previous settings.
4.1.1 Auto upgrade
It provide auto detect new firmware from Internet, and user can select to upgrade new version or not.
4.1.2 Manual upgrade
If you download firmware from website, you can upgrade firmware manual as below.
http://www.sapido.com.tw/
32
User Manual v1. 0.0
4.2 Parental Control
Parental
Control
provide URL Filtering and MAC Filter Schedule for setup
4.2.1 URL Filtering
URL Filtering is used to restrict users to access specific websites in internet http://www.sapido.com.tw/
33
User Manual v1. 0.0
Item
Enable URL Filtering
URL Address
Apply
Current Filter Table
Delete Selected & Delete
All
Description
Please select Enable MAC Filtering to filter MAC addresses
Please enter the MAC address that needs to be filt ered.
Click on Apply to save the setting data.
It will display all ports that are filt ering now.
Click
Delete Selected
will delete the selected item. Click
Delete All
will delet e all items in this table.
Notes: This function will not be in effect when the Virtual Server is enabled. Please disable Virtual Server before activate the URL Filtering function.
4.2.2 MAC Filter Schedule
When enabled, filtering will be based on the MAC address of LAN computers. Any computer with its MAC address on this list will be blocked from accessing the Internet. http://www.sapido.com.tw/
34
User Manual v1. 0.0
Item
Enable MAC Filtering
Description
Please select Enable MAC Filtering to filter MAC addresses. http://www.sapido.com.tw/
35
User Manual v1. 0.0
4.2.3 Wireless Schedule
Wireless available schedule, this page allows you setup the wireless schedule rule. Please do not forget to configure systeim before enable this feature
4.3 Office Control
Office control provide
Multiple AP
、
Wireless Access Control
、
IP Filtering
、
IP Binding
、
QoS http://www.sapido.com.tw/
36
User Manual v1. 0.0
4.3.1 Multiple AP
The GR297n can register up to 4 SSIDs (wireless LAN group). It can be used as if there are multiple wireless LAN access points with one product.
Item
Enable
SSID
Data Rate
Acce ss
http://www.sapido.com.tw/
Description
Enable or disable the service.
Enter the SSID
Select the data transmission rate.
Enable this function can let clients use two access types: a. LAN+WAN: the client can access to the Internet and access in the router’s GUI.
37
User Manual v1. 0.0
Acti ve Client List
b. WAN: the client can only access to the Internet.
Display the properties of the client which is connecting successfully.
4.3.2 Wireless Access Control
Access Control allows user to block or allow wireless clients to access this router. Users can select the access control mode, then add a new MAC address with a simple comment and click on “Apply Change” to save the new addition. To delete a MAC address, select its corresponding checkbox under the Select column and click on “Delete
Selected” button.
4.3.3 IP Filtering
When enabled, LAN clients are blocked / filtered from accessing the Internet based on their IP addresses http://www.sapido.com.tw/
38
User Manual v1. 0.0
Item
Enable IP Filtering
Local IP Address
Protocol
Apply
Current Filter Table
Delete Selected & Delete
All
Description
Please select Enable IP Filtering to filter IP addresses.
Please enter the IP address that needs to be filtered.
Please select the protocol type of the IP address
Click on
Apply
to add the setting data
It will display all ports that are filt ering now.
Click
Delete Selected
will delete the selected item. Click
Delete All
will delet e all items in this table.
4.3.4 IP Binding
This function allows you reserve IP addresses, and assign the same IP address to the network device with the specified MAC address any time it requests an IP address. This is almost the same as when a device has a static IP address except that the device must still request an IP address from the DHCP server.
Item
Enable Static DHCP
IP Address
MAC addre ss
Static DHCP Li st
Delete Selected & Delete
All
Description
Select enable to use Static DHCP function
Please enter IP address to limit
Please enter MAC address to limit
It will display all IP and MAC address you made.
Click
Delete Selected
will delete the selected item. Click
Delete All
will delet e all items in this table. http://www.sapido.com.tw/
39
User Manual v1. 0.0
4.3.5 QoS
The QoS can let you classify Internet application traffic by source/destination IP address and port number.
To assign priority for each type of application and reserve bandwidth can let you have a better experience in using critical real time services like Internet phone, video conference …etc.
Item
Enable QoS
Description
Check “Enable QoS” to enable QoS function for the WAN port. You also can uncheck “Enable QoS ” to disable QoS function for the WAN port.
Manual Uplink Speed
Manual Downlink Speed
Set the downlink speed by manual to assign the download or upload bandwidth by the unit of Kbps.
Mode
Set the uplink speed by manual to assign the download or upload bandwidth by the unit of Kbps.
Select Guaranteed minimum bandwidth or Restricted maximum bandwidth
MAC Addre ss
Uplink Bandwidth
Percentage
Set MAC Address if the address type is by MAC Address
LAN device bandwidt h of uplink bandwidth http://www.sapido.com.tw/
40
User Manual v1. 0.0
Download Bandwidth
Percentage
Add
Delete Selected & Delete
All
LAN device bandwidt h of download bandwidt h
Add the setting data
Click
Delete Selected
will delete the selected item. Click
Delete All
will delet e all items in this table.
4.4 File Menu
Only support one USB disk for Samba and FTP
4.4.1 Samba Storage
Item
Share mode
User mode
4.4.2 FTP server
Description
User can access USB disk without account and password
User need account to access USB disk
( login account is “admin”
, password is “admin”
)
. http://www.sapido.com.tw/
41
User Manual v1. 0.0
Item
Enable FTP Server
Enable Anonymous to
Login
Enable FTP Access from
WAN
Description
FTP server start or stop
Agree anonymous account login to FTP server
Allow user access device FTP server from WAN side
( internet
)
FTP Server Port
Default FTP server port is 21
Idle Connection Time-Out
FTP process should have an idle timeout, which will terminat e the process and close the control connection if the server is inactive (i.e., no command or data transfer in progress) for a long period of time
Account li st
APP Link
Add FTP user account
Provide some ipad/iphone samba app for user download http://www.sapido.com.tw/
42
User Manual v1. 0.0
4.5 Webcam server
Webcam server only support one webcam
GR297n provides 2 kinds file forma
t :
AVI for local USB disk only
JPG for USB disk or FTP server
http://www.sapido.com.tw/
43
User Manual v1. 0.0
Item
Enable Webcam
Acce ss from WAN
Connection Port
Preview
Archi ve Format Setting
Description
Webcam start or stop
Allow user to see webcam image from WAN side
( internet
)
Define webcam access por t , d efault is 8080
See webcam image
Set remote FTP server information for recording webcam image
4.6 VPN Server
The VPN Server function providing PPTP/L2TP mode are designed to allow users to an external network device / computer and office local area network to establish a secure network connection. And User can safe login office local area network and access to personal documents, files Sharing and other resources. It provides the most convenient VPN encryption. http://www.sapido.com.tw/
44
User Manual v1. 0.0
Item
Enable Setting
Connection Type
VPN Server IP
Remote IP range
Authenti cation Protocol
MPPE Encryption Mode
(RC4)
User Name
Password
Current Filter Table
Delete Selected & Delete
All
Description
Check this option, will start the VPN Server feature.
Provide PPTP or L2TP access connection type.
Input the IP address of VPN server
It is the IP range of assigned to the VPN Client
It is provided three types of authentication protocol
It is provided three encryption modes
Input the login name of the client user
Input the login password of the client user
It will display all ports that are filt ering now.
Click
Delete Selected
will delete the selected item. Click
Delete All
will delet e all items in this table.
4.7 DoS
Home:
http://www.sapido.com.tw/
45
User Manual v1. 0.0
Item
Home
Enterprise:
Description
Check “
Home
” to enable DoS function for prevention. You also can check “
No Prevention
” to disable DoS function. http://www.sapido.com.tw/
46
User Manual v1. 0.0
Item
Enterprise
Description
Check “
Enterprise
” to enable DoS function for prevention. You also can check “
No Prevention
” to disable DoS function.
4.8 Remote Management
This page allows you to access the GUI on WAN.
http://www.sapido.com.tw/
47
User Manual v1. 0.0
Item
HTTP Connection Port
Enable Web Server Access on WAN
Description
Users can access GUI by this port
, default is 80
Allow user access GUI from WAN side
4.9 Status
You could check WAN, LAN, Client net work and USB device information
WAN information
http://www.sapido.com.tw/
48
User Manual v1. 0.0
LAN information
http://www.sapido.com.tw/
49
User Manual v1. 0.0
Client information
http://www.sapido.com.tw/
50
User Manual v1. 0.0
USB device information
http://www.sapido.com.tw/
51
User Manual v1. 0.0
4.10 Factory Default
You could reset the current configuration to factory default.
4.11 Reboot
This function is used to reboot
4.12 Logout
This page is used to logout http://www.sapido.com.tw/
52
User Manual v1. 0.0
http://www.sapido.com.tw/
53
User Manual v1. 0.0
Chapter 5 Advance Setup
5.1 Internet Mode
5.1.1 Internet Setup
Please refer Internet Setup
5.1.2 AP
Please refer AP
5.1.3 WiFi AP
Please refer WiFi AP
5.1.4 WiFi ISP
Please refer WiFi ISP
5.2 IP Config
5.2.1 WAN
5.2.1.1 PPPoE
http://www.sapido.com.tw/
54
User Manual v1. 0.0
Item
User Name
Password
Service Name
Connection Type
MTU Size
DNS
Clone Mac Address
Save & Apply
http://www.sapido.com.tw/
Description
Input your us er name provided by your ISP. If you don’t know, please check with your ISP.
Input the password provided by your ISP.
Input the service name provided by your ISP.
Three types for select:
Continue s, Connect on Demand,
and
Manual.
Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
Select
Attain DNS Automatically
. Or select
Set DNS Manually
, if you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C
Address"
Click on Save to save the setting dat e, the Apply button for execute current configuration.
55
User Manual v1. 0.0
5.2.1.2 DHCP
Item
Host Name
MTU Size
DNS
Clone Mac Address
Save & Apply
5.2.1.3 Static IP
Description
You can keep the default as the host name, or input a specific name if required by your ISP.
Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
Select
Attain DNS Automatically
. Or select
Set DNS Manually
, if you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C
Address"
Click on Save to save the setting dat e, the Apply button for execute current configuration. http://www.sapido.com.tw/
56
User Manual v1. 0.0
Item
IP Address
Subnet Mask
Gateway
MTU Size
DNS
Clone Mac Address
Save & Apply
5.2.1.4 PPTP
Description
Enter the IP address which is provided by your ISP.
Please enter the Subnet Mask address
Input ISP Default Gateway Address, .
Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
Input DNS information which is provided by your ISP
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C
Address"
Click on Save to save the setting dat e, the Apply button for execute current configuration. http://www.sapido.com.tw/
57
User Manual v1. 0.0
Item
Server IP Address
User Name
Password
Description
Input your server IP address provided by your ISP. If you don’t know, please check with your ISP.
Input PPTP account provided by your ISP.
Input the password provided by your ISP.
MTU Size
Enable MPPE Encryption
Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
Microsoft Point-t o-Point Encryption (MPPE ) provides data security for the PPTP connection that is between the VPN client and VPN server.
Enable MPPC Compre ssion
Microsoft Point-to-Point Compression (MPPC) is a scheme used to compress Point-t o-Point Protocol (PPP) packets between Cisco and Microsoft client devices. The MPPC algorit hm is designed to optimize bandwidth utilization in order to support multiple simultaneous connections. The MPP C algorithm us es a
Lempel-Ziv (LZ) based algorithm with a continuous history buffer, called a dictionar
DNS
Clone Mac Address
Select
Attain DNS Automatically
. Or select
Set DNS Manually
, if you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C http://www.sapido.com.tw/
58
User Manual v1. 0.0
Save & Apply
5.2.1.5 L2TP
Address"
Click on Save to save the setting dat e, the Apply button for execute current configuration.
Item
Server IP Address
User Name
Password
MTU Size
DNS
Clone Mac Address
Save & Apply
http://www.sapido.com.tw/
Description
Input your server IP address or Host Name provided by your ISP.
If you don’t know, please check with your ISP.
Input PPTP account provided by your ISP.
Input the password provided by your ISP.
Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
Select
Attain DNS Automatically
. Or select
Set DNS Manually
, if you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C
Address"
Click on Save to save the setting dat e, the Apply button for execute current configuration.
59
User Manual v1. 0.0
5.2.1.6 3.5G
Item
Mode
Network Traffic Moni tor
Limit Internet Traffic
Connection Speed
SIM PIN
Authenti cation
DNS
http://www.sapido.com.tw/
Description
Input your us er name provided by your ISP. If you don’t know, please check with your ISP.
BRC70n will record 3.5G traffic usage volume
User can limit 3.5G traffic usage volume to prevent over budget
Provide 3 kinds of speed
, auto is recommended
SIM card P IN number
Provide 3 kinds of authentication methods
, auto is recommended
Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your
60
User Manual v1. 0.0
Clone Mac Address
Save & Apply
5.2.1.7 Smartphone
ISP in DNS 1 2 3.
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C
Address"
Click on Save to save the setting dat e, the Apply button for execute current configuration.
Item
Service
http://www.sapido.com.tw/
Description
GR297n support several kinds of smart phon e , Nokia 、 Black Berry 、
Samsung 、 iPhone 、 Andriod phone
iPhone do not need to do any setting
,
all you need is to turn on iphone hotspot function and connect it
61
User Manual v1. 0.0
SIM PIN
APN
User Name
Password
Phone number
Authenti cation
DNS
Clone Mac Address
Save & Apply
5.2.1.8 LTE to GR297n USB port
SIM card P IN number
Please check 3.5G ISP to get APN data
Please check 3.5G ISP to get user name
Please check 3.5G ISP to get password
Please check 3.5G ISP to number data
Provide 3 kinds of authentication methods
, auto is recommended
Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C
Address"
Click on Save to save the setting dat e, the Apply button for execute current configuration. http://www.sapido.com.tw/
62
User Manual v1. 0.0
Item
Mode
Network Traffic Moni tor
Limit Internet Traffic
Connection Speed
SIM PIN
Authenti cation
DNS
Clone Mac Address
Description
Input your us er name provided by your ISP. If you don’t know, please check with your ISP.
BRC70n will record 3.5G traffic usage volume
User can limit 3.5G traffic usage volume to prevent over budget
Provide 3 kinds of speed
, auto is recommended
SIM card P IN number
Provide 3 kinds of authentication methods
, auto is recommended
Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C
Address" http://www.sapido.com.tw/
63
User Manual v1. 0.0
Save & Apply
Click on Save to save the setting dat e, the Apply button for execute current configuration.
5.2.2 LAN
Use this page to set up the local IP address and subnet mask for your router.
Please select
LAN Interface Setup
under the
IP Config
menu and follow the instructions below to enter the LAN setting page to configure the settings you want.
Item
IP Address
Subnet Mask
Gateway
DHCP
http://www.sapido.com.tw/
Description
The default value of LA N IP address is
192.168.1. 1
for this router.
Input Subnet Mask, normally it is 255.255.255.0.
Input ISP Default Gateway Address. If you don’t know, please check with your ISP.
Enable or disable DHCP services. The DHCP server will automatically allocat e an unused IP address from the IP address
64
User Manual v1. 0.0
DHCP Client Range
DHCP Lease Time
Static DHCP
Domain Name
802.1d Spanning Tree
pool to the requesting computer if enabled.
Define the DHCP client range and then the DHCP server will assign an IP to the requesting computer from t his range. The
Show Client
will display every assigned IP address, MAC address, and ex pired time. The default range is 192.168.1.100 -
192.168.1.200.
IP avaliable time
The name of device
IEEE 802. 1d Spanning Tree Protocol (STP)
is a link layer network protocol t hat ensures a loop-free topology for any bridged
LAN. The main purpos e of S TP is to ensure that you do not create loops when you have redundant paths in your net work. Loops are deadly to a network.
Copy the MAC address from the device you had registered to your
ISP if your ISP asks for the specific MAC A ddress.
Clone MAC
Addre ss
5.2.3 DDNS
You can assign a fixed host and domain name to a dynamic Internet IP address. Each time the router boots up, it will re-register its domain-name-to-IP-address mapping with the DDNS service provider. This is the way Internet users can access the router through a domain name instead of its IP address.
Note: make sure that you have registered with a DDNS service provider before enabling this feature. http://www.sapido.com.tw/
65
User Manual v1. 0.0
Please enter Domain Name, User Name/Email, and Password/Key. After entering, click on
Apply Changes to save the setting, or you may click on Reset to clear all the input data.
Item
Enable/Disable DDNS
Service Provider
User Name/Email
Password/Key
Save & Apply
Description
Select enable to use DDNS function. Each time your IP address to
WAN is changed, and the information will be updated to DDNS service provider automatically.
Choose correct Service Provider from drop-down list, here including
DynDNS, TZO, ChangeIP, Eurodns, OVH, NO-IP, ODS, Regfish embedded in
GR297N
.
User name is used as an identity to login Dynamic-DNS service.
Password is applied to login Dynamic-DNS servic e.
Click on “Save” to save the setting data. The “A pply” button can execute current configuration
5.3 IPv6 Config
http://www.sapido.com.tw/
66
User Manual v1. 0.0
Item
Origin Type
WAN Link Type
PPPoE
Child Prefix Address
Static IP
Router Name
DNS v6
Description
SLAA
C 、 DHCPv6 、 IP 。 Please check ISP to get correct type
PPPo
E 、 IP
Use IPv4 PPPoE account and password to do IPv6 connect
Check ISP to get this data
Check ISP to get IP address and default gateway IP address
Router domain
Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your
ISP in DNS http://www.sapido.com.tw/
67
User Manual v1. 0.0
5.4 Wireless
5.4.1 Basic Settings
This page is used to configure the parameters for wireless LAN clients who may connect to your Access Point. Here you may change wireless encryption settings as well as wireless network parameters http://www.sapido.com.tw/
68
User Manual v1. 0.0
Item
Di sable Wireless
Band
Mode
Network Type
SSID
Channel Width
Control Sideband
Channel Number
Broadband SSID
WMM
Data Rate
Associate Clients
Enable MAC Clone
(Single Ethernet Client)
Enable Universal Repeater
Mode (Acting a s AP and
Description
Turn off the wireless service.
Select the frequency. It has 6 options: 2.4 GHz
(B/G/N/B+G/G+N/B+G+N).
Select the mode. It has 3 modes to select: (AP, Client, WDS,
AP+WDS).
Multiple AP: Please check Section 4.1.2.1.
* In Wi-Fi AP mode only support Client mode.
Infrastructure
: one of the two methods for connecting to wireless networks with Wi-Fi enabled devices such as laptops, Pda’s I-phone etc. These devices are connected to wireless network with the help of Access point (AP). Wireless
Access Points are usually routers or switches which are connected to internet by Ethernet port.
Ad hoc
:
By using ad hoc mode, devices are capable for communicating directly with each other. No Access point
(routers / switches) is required for communication between devic es and all devic es in the range connect in peer to peer communication mode.
Service S et identifier, users can define to any or keep as default.
Please select the channel width, it has 3 options: 20MHz / 40MHz /
Auto
Enable this function will control your router use lower or upper channel.
Please select the channel; it has Auto, 1, 2~11 or 13 options.
User may choose to enable
Broadca st SSID
Enable / Disable Wi-Fi Multimedia
Please select the data transmission rate. or not.
Check the AP connectors and the Wireless connecting status.
Clone the MAC address for ISP to identify.
Allow to equip with the wireless way conjunction upper level, provide the bottom layer user link in wireless and wired way in the http://www.sapido.com.tw/
69
User Manual v1. 0.0
Client simultaneousl y)
meantime.
(The IP that bottom layer obtains is from upper level.) Please also check Section 4.1.2.2
SSID of Extended Interface
While linking the upper level device in wireless way, you can set
SSID to give the bottom layer user search.
Multiple AP
GR297n can register up to 4 SSIDs (wireless LAN group).
It can be used as if there are multiple wireless LAN access points with one product. Each SSID could be set with different data rate, WMM and access type
Save & Apply
Click on “Save” to save the setting data. The “A pply” button can execute current configuration
5.4.2 Advanced Settings
Item
Fragment Threshold
RTS Thre shold
http://www.sapido.com.tw/
Description
To identify the maxima length of packet, the over length packet will be fragmentized. The allowed range is 256-2346, and default length is
2346.
This value should remain at its default setting of 2347. The range is
0~2347. Should you encounter inconsistent data flow, only minor modifications are recommended. If a net work packet is smaller than the present RTS threshold size, the RTS/CTS mechanism will not be enabled. The router sends Request to Send (RTS ) frames to a particular receiving station and negotiates the sending of a data
70
User Manual v1. 0.0
Beacon Interval
Preamble Type
IAPP
Protection
Aggregation
Short GI
WLAN Partition
20/40MHz Coexist
RF Output Power
frame. After receiving an RTS, the wireless station responds with a
Clear to Send (CTS ) frame to acknowledge the right to begin transmission. Fill the range from 0 to 2347 into this blank.
Beacons are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. The allowed setting range is 20-1024 ms..
PLCP is Physical layer convergence protocol and PPDU is PLCP protocol data unit during transmission, the PSDU shall be appended to a PLCP preamble and header to create the PPDU. It has 2 options: Long Preamble and Short Preamble.
Inter-Access Point Protocol is a recommendation that describes an optional extension to IEEE 802. 11 that provides wireless access-point communications among multivendor systems.
Please select to enable wireless protection or not.
Enable this function will combine several packets to one and transmit it. It can reduce the problem when mass packets are transmitting.
Users can get better wireless transmission efficiency when they enable this function.
Shut down th e c om m unic ation betw een th e c onnec ted wireles s LAN de vic es .
If y ou s et up as "Ena ble d", dev ic es c onnec ted with the router, s uc h as a pr inte r, wi ll not be a ble to us e.
Default Sett ing: "Dis ab led "
Config ure 2 0/40 MHz c oe xis tin g s c hem e.
If yo u s et u p as "Ena ble d", "20 MHz " and "40 MHz " w ill c oexis t.
Norm all y us e as "Dis abl ed".
Default Sett ing: "Dis ab led "
Users can adjust RF out put power to get the best wireless net work environment. Users can choose from 100%, 70%, 50%, 35%, and
15%.
5.4.3 Security
Here users define the security type and level of the wireless network. Selecting different methods provides different levels of security.
Please note that using any encryption may cause a significant degradation of data throughput on the wireless link.
There are five Encryption types supported: “None”, “WEP”, “WPA”, ”WPA2”, and “WPA-Mixed”.
Enabling WEP can protect your data from eavesdroppers. If you do not need this feature, select “None” to skip the following setting http://www.sapido.com.tw/
71
User Manual v1. 0.0
Item
WEP
WPA / WPA2
WPA-Mixed
802.1x Authenti cation
Radius
Personal (Pre-Shared
Key)
http://www.sapido.com.tw/
Description
W E P is t he mos t ge ne r al e nc ry pt i on s c h em e am on g wir el es s LA N s ec u rit y, c on fig u re t h e c om mo n e nc ry pt ed k ey (W E P K ey ) f or ac c es s p oint an d wi r eles s LA N ha nds et .
W E P k ey lengt h a re " 6 4b it " , " 128 bit " , a nd " 2 5 6bit " ( This pr od uc t c or res po nds up t o 12 8bit ), la rg er t he va lu e is , mor e t h e c h ar ac t e r c a n b e s et , a nd enc ry pt i on s t r en gt h will en ha nc e d.
* I f y o u c on fi gu r e t he enc ry pt io n k ey as " 5 l et t e rs in hal f -wi dt h alp ha bet s a nd nu mb ers " o r " H ex a dec i mal i n 1 0 digit s " , pl eas e s elec t " 6 4- bit " .
* I f y o u c on fi gu r e t he enc ry pt io n k ey as " 1 3 l et t ers i n hal f -wi dt h alp ha bet s a nd nu mb ers " o r " H ex a dec i mal i n 2 6 digit s " , pl eas e s elec t " 1 28 -b it " .
W PA / W PA 2 is wir eles s LA N s ec urit y s t an da r d w hic h is s t ren gt h en o ve r W E P. On W PA -P S K / W PA 2-P S K , us es enc ry pt e d k ey c all ed pr e-s ha re d k ey, a nd s et up c omm on enc ry pt io n k ey fo r ac c es s p oint an d w ir eles s LA N h a nds et lik e W E P. The re ar e " A E S " a nd " TK IP " as e nc ry pt io n s c hem e. " TK IP " aut o mat ic ally up d at es t h e k ey at r eg ul ar int e r vals , c hec k a nd a pp r o ve t he c o mmu nic at i o n, s o it c an c ommu nic at e s a fe r t h an W E P k ey w hic h us es s in gle enc ry pt io n k ey fo r lo ng t im e. " A E S " is ha rd er t o d ec od e c omp ari ng t o " TK IP " , s o it c a n s ay t o ug he r e nc ry pt io n s c hem e t ha n " TK IP "
Support WPA and WPA2 at the same time
For radius server authentication
* I f y o u c on fi gu r e P r e-S ha re d K ey as " Hex ad ec im al in 64 digit s " , pl eas e s elec t " H ex ( 64 c h a rac t e rs ) " .
* I f y o u c on fi gu r e enc ry pt i on k ey i n " 8 t o 63 l et t ers i n hal f -wi dt h alp ha bet s a nd nu mb ers " , pl eas e s el ec t
72
User Manual v1. 0.0
" P as s ph ras e
5.4.4 Access Control
Please refer Wireless Access Control
5.4.5 WPS
This page allows user to change the setting for WPS (Wi-Fi Protected Setup). Using this feature could let your wireless client atomically synchronize it’s setting and connect to the
Access Point in a minute without any hassle. SAPIDO GR297N could support both Self-PIN or PBC modes, or use the WPS button (at real panel) to easy enable the WPS function.
PIN model,
in which a PIN has to be taken either from a sticker label or from the web interface of the WPS device. This PIN will then be entered in the AP or client WPS device to connect.
PBC model,
in which the user simply has to push a button, either an actual or a virtual one, on both WPS devices to connect.
GR297n WPS only support no encryption and WPA2
Please follow instructions below to enable the WPS function.
1. Setup Wireless LAN with WPS PIN :
(1). Get the WPS PIN number from wireless card and write it down. http://www.sapido.com.tw/
73
User Manual v1. 0.0
(2).
(3). Fill in the PIN number from the wireless card in Client PIN Number field, and then click “Start PIN”.
(4). Click PIN from Adapter Utility to complete the WPS process with the wireless router.
(5). Wireless dongle should connect to GR297n http://www.sapido.com.tw/
74
User Manual v1. 0.0
2. Start PBC:
(1). Press the GR297n WPS button and wait for WPS LED blinking
(2). Press the dongle WPS button
(3). Wireless dongle should connect to GR297n
5.4.6 WDS
When selected in the Basic Settings page and enabled here, Wireless Distribution System
(WDS) enables the router to be used as a wireless bridge. Two Wireless-N Routers in bridge mode can communicate with each other through their wireless interfaces. To accomplish this, all wireless routers should be set to the same channel and the MAC address of other AP /
Routers should be entered in the table.
The WDS explanation is as the following picture.
Router_A
:
Set the connection mode to “AP+WDS” from “Wireless Basic Setting”, and then select the channel number (in this example is "11”). Click Apply Changes to save the setting. http://www.sapido.com.tw/
75
User Manual v1. 0.0
Please check the MAC address
Enable WDS function from the page – “WDS Setting”, and then fill in the MAC address of Router_B. Click Apply Changes to save the setting data. http://www.sapido.com.tw/
76
User Manual v1. 0.0
Select encryption for security
Rout er_B mac address
The WDS AP List will show the WDS device MAC address.
Router_B
:
Setup Router_B WDS. http://www.sapido.com.tw/
77
User Manual v1. 0.0
Select encryption for security
Rout er_A mac address
Router_B LAN PC will get IP address from Router_A.
If you failed the WDS setting, please check you setting with refer to the list below.
Wireless Mode
LAN IP Address
Router_A
AP+WDS
Set the same segment as the router B(Note 1)
Router_B
WDS
Set the same segment as the router_A (Note 1)
Security
Example :192.168.1.1
Set the same security as
Rout er_B
Enable
Example :192.168.1.2
Set the same security as
Rout er_A
Disable DHCP
Note 1: LA N IP address should be under the same segment but cannot be the same number. http://www.sapido.com.tw/
78
User Manual v1. 0.0
5.4.7 Schedule
Please refer Wireless Schedule
5.5 NAT
This section contains configurations for the GR297N ’s advanced functions such as: virtual server, and DMZ to provide your network under a security environment.
5.5.1 DMZ
The DMZ feature allows one local user to be exposed to the Internet for special-purpose applications like Internet gaming or videoconferencing. When enabled, this feature opens all ports to a single station and hence renders that system exposed to intrusion from outside.
The port forwarding feature is more secure because it only opens the ports required by that application.
Item
Enable DMZ
DMZ Host IP Address
Description
It will enable the DMZ service if you select it.
Please enter the specific IP address for DMZ host.
5.5.2 Virtual Server
The Virtual Server feature allows users to create Virtual Servers by re-directing a particular range of service port numbers (from the WAN port) to a particular LAN IP address. http://www.sapido.com.tw/
79
User Manual v1. 0.0
Item
Enable Virtual Server
Addre ss
Protocol
Description
Select to enable virt ual server or not.
Specify the IP address which receives the incoming packets.
Select the protoc ol type.
Public Port Range
Private Port Range
Enter the port number, for example 80-80.
Enter the port number, for example 20-22.
Current Port Forwarding
Table
It will display all port forwarding regulation you made.
Delete Selected & Delete
All
Click
Delete Selected
will delete the selected item. Click
Delete All
will delet e all items in this table.
Please find the following figure to know that what the virtual server is. The web server is located on 192.168.1.100, forwarding port is 80, and type is TCP+UDP. http://www.sapido.com.tw/
80
User Manual v1. 0.0
5.6 AirCloud Storage
Please refer File Menu
5.7 AirCloud Monitor
Please refer Webcam server
5.8 VPN Server
Please refer VPN server
5.9 Firewall
5.9.1 DoS
Please refer DoS
http://www.sapido.com.tw/
81
User Manual v1. 0.0
5.5.2 QoS
Item
Enable QoS
Automatic uplink speed
Manual Uplink speed
Automatic downlink speed
Manual Downlink speed
Addre ss Type
Local IP Address
Description
Check “Enable QoS” to enable QoS function for the WAN port. You also can uncheck “Enable QoS ” to disable QoS function for the WAN port.
Check the Automatic uplink speed.
Input
uplink
bandwidth manually
Check the Automatic downlink speed.
Input
downlink
bandwidt h manually
Set QoS by IP Address or MAC address
Set local IP Address if the address type is by IP Address http://www.sapido.com.tw/
82
User Manual v1. 0.0
MAC Addre ss
Mode
Uplink Bandwidth
Downlink Bandwidth
Set MAC Address if the address type is by MAC Address
Select Guaranteed minimum bandwidth or Restricted maximum bandwidth
Key in the bandwidth.
Key in the bandwidth.
5.5.3 Port Filtering
When enabled packets are denied access to Internet/filtered based on their port address.
Item
Enable Port Filtering
Port Range
Protocol
Add
Current Filter Table
Delete Selected & Delete
All
Description
Select Enable Port Filtering to filter ports.
Enter the port number that needs to be filtered.
Please select the protocol type of the port.
Click on
Add
to save the setting data.
It will display all ports that are filt ering now.
Click
Delete Selected
will delete the selected item. Click
Delete All
will delet e all items in this table.
Port 80 has been blocked as the following illustrate. http://www.sapido.com.tw/
83
User Manual v1. 0.0
IP: 192.168.1.x
Port: 80-80
5.5.4 IP Filtering
Please refer IP Filtering
5.5.5 Mac Filter Schedule
Please refer Mac Filter Schedule
5.5.6 URL Filtering
Please refer URL Filtering
5.5.7 IP Binding
Please refer IP Binding
5.5.8 VLAN
http://www.sapido.com.tw/
84
User Manual v1. 0.0
Item
Forwarding Rule
Tag
VID
Priority
CIF
Description
Bridge or NAT mode
Add VLAN tag to packet
Set VLAN ID
(
1~ 4096
)
It indicates the frame priority level. Values are from 0 (best effort) to
7 (highest); 1 represents the lowest priority
Enable or Disable CIF
5.10 System
This section including
Wake on LAN, Change Username/Password, Upgrade Firmware,
Profiles Save, Remote Management, Time Zone, UPnP, Route Setup, VPN Passthrough, and Wan Type Auto Detection
. It is easy and helpful for users making more detailed settings.
5.10.1 Wake on Lan
Switch your computer ON through your LAN or the Internet . To support WOL you must have a computer with Motherboard that supports WOL, as well as a Network Controller (NIC) supporting http://www.sapido.com.tw/
85
User Manual v1. 0.0
this function. Most of the newer Motherboard (circa 2002 and On), have an On Board NIC that supports WOL. Otherwise you need to install a PCI NIC that is WOL capable.
5.10.2 Change Password
Users can set or change user name and password used for accessing the web management interface in this section.
Input User Name and New Password, then input Confirm Password again.
5.10.3 Firmware Upgrade
Please refer Firmware Upgrade
5.10.4 Profiles Save
http://www.sapido.com.tw/
86
User Manual v1. 0.0
Users can create a backup file that contains current router settings. This backup file can be used to restore router settings. This is especially useful in the event you need to reset the router to its default settings.
1. Save Configuration
(1). Click Save
(2). Please click “Save” to save the configuration to your computer.
(3). Select the location which you want to save file, then click Save. http://www.sapido.com.tw/
87
User Manual v1. 0.0
2. Load configuration file
(1). Tap “browse” and select configuration file then click Open
(2). Click Upload to upload configuration file to GR297N .
(3). After 60 seconds, GR297N will reboot automatically. http://www.sapido.com.tw/
88
User Manual v1. 0.0
5.10.5 Remote Management
Please refer Remote Management
5.10.6 Time Zone
Users can synchronize the local clock on the router to an available NTP server (optional).
To complete this setting, enable NTP client update and select the correct Time Zone.
Item
Time Zone Select
Enable NTP client update
Automatically Adjust
Daylight Saving
NTP Server
Save & Apply
Description
Please select the time zone.
Please select to enable NTP client update or not.
Please select to enable Automatically Adjust Daylight Saving or not.
Please select the NTP server from the pull-down list, or you can enter the NTP server IP address manually.
Click on Save to save the setting dat e, the Apply button for execute current configuration.
5.10.7 UpnP
http://www.sapido.com.tw/
89
User Manual v1. 0.0
UPNP
Universal Plug and Play (UPnP) is a standard of networking protocols promulgated by the UPnP Forum. The goals of UPnP are to allow devices to connect seamlessly and to simplify the implementation of networks in the home (data sharing, communications, and entertainment) and in corporate environments for simplified installation of computer components. GR297N supports UPnP function, and can cooperate with other UPnP devices. When you activate UPnP, please click My Network Places. Users will see an Internet
Gateway Device icon. By click the icon, users can enter the GUI of the router. If you do not wish to use UPnP, you can disable it.
AV UPNP
AV UPnP media server is the UPnP-server that provides media library information and streams media-data (like audio/video/picture/files) to UPnP-clients on the network. It is a computer system or a similar digital appliance that stores digital media, such as photographs, movies, or music and shares these with other devices. User can plug in
USB disk to product USB port and use AV UPnP client to play USB disk media-data
(like audio/video/picture/files)
5.10.8 Route Setup
Dynamic routing is a distance-vector routing protoc ol, which employs the hop count as a routing metric. RIP prevents routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for RIP is 15
Static routing is a data communication concept describing one way of configuring path selection of rout ers in computer networks. It is the type of routing characterized by the absence of communication between rout ers regarding the current topology of the net work. This is achieved by manually adding routes to the router routing table. http://www.sapido.com.tw/
90
User Manual v1. 0.0
Item
Enable Dynamic Route
NAT
Transmit
Receive
Description
Enable or Disable dy namic route
Enable or Disable NAT function
There are 3 options
:
1. Disable
: do not send any RIP packet out
2. Send RIP 1 packet out
3. Send RIP 2 packet out
There are 3 options
:
4. Disable
: do not rec eive any RIP packet
5. Only receive RIP 1 packet
6. Only receive RIP 2 packet
Item
Enable Static Route
IP Address
Subnet Mask
Gateway
http://www.sapido.com.tw/
Description
Enable or Disable dy namic route
Destination IP address
Destination IP subnet mask
Gateway IP address for destination
91
User Manual v1. 0.0
Metric
Interface
Metric number on router’s routing table
Static route rule for LA N or WAN interface
5.10.9 VPN Passthough
Virtual Private Networking (VP N) is typically used for work-related net working. For VP N tunnels, the router supports IPSec, Pass-through, PPTP Pass-through, and L2TP Pass-through.
Item
IPSec Pass-through
PPTP Pass-through
L2TP Pass-through
IPV6 Pass-through
Description
Internet Protocol Security (IPSec) is a suite of protocols used to implement secure exchange of packets at the IP layer. To allow
IPSec tunnels to pass through the router, IPSec Pass-through is enabled by default. To disable IPSec Pass-through , select Disable
Point-to-P oint Tunneling Protocol is the method used to enable
VPN sessions to a Windows NT 4.0 or 2000 server. To allow PPTP tunnels to pass through the router, PPTP Pass-through is enabled by default. To disable PP TP Pass-through, select Disable.
To allow the L2TP net work traffic to be forwarded to its destination without the network address translation tasks.
Allow IPV 6 packet to be forwarded to its destination without the network address translation tasks.
5.10.10 Wan Type Auto Detection
http://www.sapido.com.tw/
92
User Manual v1. 0.0
http://www.sapido.com.tw/
93
User Manual v1. 0.0
Chapter 6 Q & A
6.1 Installation
1. Q: Where is the XDSL Router installed on the network?
A: In a typical environment, the Router is installed between the XDSL line and the LAN.
Plug the XDSL Router into the XDSL line on the wall and Ethernet port on the Hub
(switch or computer).
2. Q: Why does the throughput seem slow?
A: To achieve maximum throughput, verify that your cable doesn’t exceed 100 meter. If you have to do so, we advise you to purchase a bridge to place it in the middle of the route in order to keep the quality of transmitting signal. Out of this condition you would better test something else.
Verify network traffic does not exceed 37% of bandwidth.
Check to see that the network does not exceed 10 broadcast messages per second.
Verify network topology and configuration.
6.2 LED
1. Why doesn’t GR297N power up?
A: Check if the output voltage is suitable, or check if the power supply is out of order.
2. The Internet browser still cannot find or connect to GR297N after verifying the IP address and LAN cable, the changes cannot be made, or password is lost.
A: In case GR297N is inaccessible; you can try to restore its factory default settings.
Please press the “Reset” button and keep it pressed for over 7 seconds and the light of STATUS will vanish. The LEDs will flash again when reset is successful.
3. Why does GR297N shut down unexpectedly?
A: Re-plug your power adapter. Then, check the STATUS indicator; if it is off, the internal flash memory is damaged. For more help, please contact with your provider.
6.3 IP Address
http://www.sapido.com.tw/
94
User Manual v1. 0.0
1. Q: What is the default IP address of the router for LAN port?
A: The default IP address is 192.168.1.1 with subnet mask 255.255.255.0
2. Q: I don't know my WAN IP.
A: There are two ways to know.
Way 1: Check with your Internet Service Provider.
Way 2: Check the setting screen of GR297N . Click on
Status & Log
item to select
Network Configuration
on the Main Menu. WAN IP is shown on the WAN interface.
3. How can I check whether I have static WAN IP Address?
A: Consult your ISP to confirm the information, or check Network Configuration in
GR297N ’s Main Menu.
4. Will the Router allow me to use my own public IPs and Domain, or do I have to use the IPs provided by the Router?
A: Yes, the Router mode allows for customization of your public IPs and Domain.
6.4 OS Setting
1. Why can’t my computer work online after connecting to GR297N ?
A: It’s possible that your Internet protocol (TCP/IP) was set to use the following IP address. Please do as the following steps. (Windows 2000 & XP)
Start
>
Settings
>
Network and Dial-up Connections
> double click on
Internet Protocol(TCP/IP)
> select
obtain IP address automatically
>
Click on
OK
button. Then, open Internet browser for testing. If you still can’t go online, please test something else below.
Verify network configuration by ensuring that there are no duplicate IP addresses.
Power down the device in question and ping the assigned IP address of the device. Ensure no other device responds to that address.
Check that the cables and connectors or use another LAN cable.
2. Q: Why can't I connect to the router's configuration utility?
http://www.sapido.com.tw/
95
User Manual v1. 0.0
A: Possible Solution 1: Make sure that your Ethernet connect properly and securely.
Make sure that you've plugged in the power cord.
Possible Solution 2: Make sure that your PC is using an IP address within the range of 192.168.1.2 to 192.168.1.254. Make sure that the address of the subnet mask is
255.255.255.0. If necessary, the Default Gateway data should be at 192.168.1.1. To verify these settings, perform the following steps:
Windows 2000, or XP Users:
1. Click on Windows
Start
> click on
Run
> input
cmd
> click on
OK
button.
2. At the DOS prompt, type ipconfig/all.
3. Check the IP Address, Subnet Mask, Default Gateway data. Is this data correct? If the data isn't correct. Please input
ipconfig/release
> press
Enter
> input
ipconfig/renew
> press
Enter
.
Possible Solution 3: Verify the connection setting of your Web browser and verify that the HTTP Proxy feature of your Web browser is disabled. Make these verifications so that your Web browser can read configuration pages inside your router. Launch your
Web browser.
Internet Explorer Users:
1. Click on
Tools
>
Internet Options
>
Connections tab
.
2. Select
never dial a connection
, click on
Apply
button, and then click on
OK
button.
3. Click on
Tools
and then click on
Internet Options
.
4. Click on
Connections
and then click on
LAN Settings
.
5. Make sure none of the check boxes are selected and click on
OK
button.
6. Click on OK button.
Netscape Navigator Users:
1. Click on
Edit
>
Preferences
> double-click
Advanced
in the Category window.
2. Click on
Proxies
> select
Direct connection to the Internet
> click on
OK
button.
3. Click on
Edit again
and then click on
Preferences
.
4. Under category, double-click on
Advanced
and then click on
Proxies
.
5. Select
Direct connection to the Internet
and click on
OK
button.
6. Click on
OK
button.
3. Q: Web page hangs, corrupt downloads, or nothing but junk characters is being displayed on the screen. What do I need to do?
http://www.sapido.com.tw/
96
User Manual v1. 0.0
A: Force your NIC to 10Mbps or half duplex mode, and turn off the "Auto-negotiate" feature of your NIC as a temporary measure. (Please look at the Network Control
Panel, in your Ethernet Adapter's Advanced Properties tab.)
4. Q: Why can't I connect to the Web Configuration?
A: you can remove the proxy server settings in your web browser.
6.5
GR297N
Setup
1. Q: Why does GR297N ’s setup page shut down unexpectedly?
A: If one of the pages appears incompletely in GR297N ’s setup pages, please click on
Logout item on the Main Menu before shutting it down. Don’t keep it working. Then, close Internet browser and open it again for going back to the previous page.
2. Q: I don’t know how to configure DHCP.
A: DHCP is commonly used in the large local network. It allows you to manage and distribute IP addresses from 2 to 254 throughout your local network via GR297N .
Without DHCP, you would have to configure each computer separately. It’s very troublesome. Please Open
Internet browser
> Input
192.168.1.1 in the website blank field
> Select
DHCP Server under
the
IP Config Menu
. For more information, please refer to 3.3.2 (Router Mode) or 4.3.1 (AP Mode).
3. Q: How do I upgrade the firmware of GR297N ?
A: Periodically, a new Flash Code is available for GR297N on your product supplier’s website. Ideally, you should update GR297N ’s Flash Code using
Firmware
Upgrade
on the
System Management
menu of GR297N Settings.
4. Q: Why is that I can ping to outside hosts, but cannot access Internet websites?
A: Check the DNS server settings on your PC. You should get the DNS servers settings from your ISP. If your PC is running a DHCP client, remove any DNS IP address setting. As the router assign the DNS settings to the DHCP-client-enabled PC.
5. Q: GR297N couldn’t save the setting after click on Apply button?
A: GR297N will start to run after the setting finished applying, but the setting isn’t written into memory. Here we suggest if you want to make sure the setting would be written into memory, please reboot the device via
Reboot
under
System Management
directory
.
http://www.sapido.com.tw/
97
User Manual v1. 0.0
6.6 Wireless LAN
1. Q: Why couldn’t my wireless notebook work on-line after checking?
A: Generally, Wireless networks can sometimes be very complicated to set up, particularly if you're dealing with encryption and products from different vendors. Any number of variables can keep your workstations from talking to each other. Let's go over some of more common ones.
For starters, verify that your router and your workstation are using the same SSID descriptions. SSID acts as a password when a mobile device tries to connect to the wireless network. The SSID also differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID. A workstation will not be permitted to connect to the network unless it can provide this unique identifier. This is similar to the function of your network's
Workgroup or Domain name.
When you're experiencing conductivity problems, it is always best to keep things simple. So next you are going to do is that, please disable any WEP encryption you might have configured.
Successful implementation of encryption also includes the use of a shared key. A
HEX key is the most common, but other formats are also used. This key identifies the workstation to the router as a trusted member of this network. Different manufacturers can implement this key technology in ways that might prevent them from working correctly with another vendor's products. So pay attention to detail is going to be the key to a successful installation.
Next make sure the router and the NIC are configured to use the same communications channel. There are normally 11 of them, and the default channel can also vary from vendor to vendor. You might also want to confirm that the router has DHCP services enabled and an address pool configured. If not, the NIC won't be able to pick up an IP address. I have run across a few access points that offer DHCP services but do not assign all of the needed IP information to the NIC. As a result, I was able to connect to the network, but could not browse the web. The point is, don't assume anything. Verify for yourself that all of the required settings are being received by the workstation.
Finally, you might want to keep the system you're trying to configure in the same room as the router, at least during the initial configuration, in order to minimize potential interference from concrete walls or steel beams. http://www.sapido.com.tw/
98
User Manual v1. 0.0
2. Q: My PC can’t locate the Wireless Access Point.
A: Check the following:
Your PC is set to Infrastructure Mode. (Access Points are always in Infrastructure
Mode.)
The SSID on your PC and the Wireless Access Point are the same. Remember that the SSID is case-sensitive. So, for example “Workgroup” does NOT match
“workgroup”.
Both your PC and the Wireless Access Point must have the same setting for
WEP. The default setting for the Wireless Router is disabled, so your wireless station should also have WEP disabled.
If WEP is enabled on the Wireless Router, your PC must have WEP enabled, and the key must match.
If the Wireless Router’s Wireless screen is set to Allow LAN access to selected
Wireless Stations only, then each of your Wireless stations must have been selected, or access will be blocked.
To see if radio interference is causing a problem, see if connection is possible when close to the Wireless Access Point. Remember that the connection range can be as little as 100 feet in poor environments.
3. Q: Wireless connection speed is very slow.
A: The wireless system will connect at highest possible speed, depending on the distance and the environment. To obtain the highest possible connection speed, you can experiment with following:
Access Point location: Try adjusting the location and orientation of the Access
Point.
Wireless Channel: If interference is the problem, changing to another channel may show a marked improvement.
Radio Interference: Other devices may be causing interference. You can experiment by switching other devices off, and see if this helps. Any “noisy” devices should be shielded or relocated.
RF Shielding: Your environment may tend to block transmission between the wireless stations. This will mean high access speed is only possible when close to the Access Point.
4. Q: Some applications do not run properly when using the Wireless Router.
http://www.sapido.com.tw/
99
User Manual v1. 0.0
A: The Wireless Router processes the data passing through it, so it is not transparent.
Use the Special Application feature to allow the use of Internet applications which do not function correctly. If this does solve the problem, you can use the DMZ function.
This should work with almost every application, but:
It is a security risk, since the firewall is disabled.
Only one (1) PC can use this feature.
5. Q: I can’t connect to the Wireless Router to configure it.
A: Check the following:
The Wireless Router is properly installed, LAN connections are OK, and it is powered ON.
Make sure that your PC and the Wireless Router are on the same network segment.
If your PC is set to “Obtain an IP Address automatically” (DHCP client), restart it.
If your PC uses a Fixed (Static) IP address, make sure that it is using an IP
Address within the range 192.168.1.129 to 192.168.1.253 and thus compatible with the Wireless Router’s default IP Address of 192.168.1.254. Also, the
Network Mask should be set to 255.255.255.0 to match the Wireless Router. In
Windows, you can check these settings by using Control Panel ~ Network to check the Properties for the TCP/IP protocol.
6. Q: The WinXP wireless interface couldn’t communicate the WEP with SAPIDO
GR297N’s wireless interface.
A: The default WEP of WinXP is
Authentication Open System - WEP
, but the WEP of
SAPIDO GR297N is only for
Shared Key - WEP
, it caused both sides couldn’t communicate. Please select the WEP of WinXP from Authentication Open System to
Pre-shared Key - WEP
, and then the WEP wireless interface between WinXP and
SAPIDO GR297N would be communicated.
6.7 Support
1. Q: What is the maximum number of IP addresses that the XDSL Router will support?
A: The Router will support to 253 IP addresses with NAT mode. http://www.sapido.com.tw/
100
User Manual v1. 0.0
5. Q: Is the Router cross-platform compatible?
A: Any platform that supports Ethernet and TCP/IP is compatible with the Router.
6.8 Others
1. Q: Why does the router dial out for PPPoE mode very often?
A: Normally some of game, music or anti-virus program will send out packets that trigger the router to dial out, you can close these programs. Or you can set the idle time to 0, then control to dial out manually.
2. Q: What can I do if there is already a DHCP server in LAN?
A: If there are two DHCP servers existing on the same network, it may cause conflict and generate trouble. In this situation, we suggest to disable DHCP server in router and configure your PC manually. http://www.sapido.com.tw/
101
User Manual v1. 0.0
Chapter 7 Appendices
7.1 Operating Systems
1. Microsoft
:
Windows 2000, XP, Vista, Windows 7.
2. Apple
:
Mac OS X 10.4.7, Leopard and the following related versions.
3. Linux
:
Redhat 9, Fedora 6 & 7, Ubuntu 7.04 and the following related versions.
7.2 Browsers
1. Internet Explorer ver. 6 and 7 and the following related versions.
2. FireFox ver. 2.0.0.11 and the following related versions.3.
3. Safari ver. 3.04 and the following related versions.
7.3 Communications Regulation Information
Should any consumers need to learn more information, services and supports, please contact the supplier of your product directly. http://www.sapido.com.tw/
102
User Manual v1. 0.0
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Table of Contents
- 6 FCC Caution
- 8 Introduction
- 8 Product Appearance
- 9 System and Network Setup
- 9 Build Network Connection
- 10 Connecting GR297N
- 10 Network setup
- 10 Windows 2000
- 11 Windows XP
- 12 Windows Vista / Windows 7
- 14 Router IP Address Lookup
- 15 Log into Web GUI
- 16 Internet Connection
- 16 Using as a broadband router
- 17 Home button menu
- 20 Internet Setup
- 21 PPPoE
- 21 DHCP
- 23 Static IP
- 23 PPTP
- 25 L2TP
- 26 WiFi ISP
- 26 3.5G
- 27 Smartphone
- 29 LTE
- 29 AP
- 30 WiFi AP
- 32 GUI Function Setup
- 32 Firmware Upgrade
- 32 Auto upgrade
- 32 Manual upgrade
- 33 Parental Control
- 33 URL Filtering
- 34 MAC Filter Schedule
- 36 Wireless Schedule
- 36 Office Control
- 37 Multiple AP
- 38 Wireless Access Control
- 38 IP Filtering
- 39 IP Binding
- 40 QoS
- 41 File Menu
- 41 Samba Storage
- 41 FTP server
- 43 Webcam server
- 44 VPN Server
- 45 DoS
- 47 Remote Management
- 48 Status
- 52 Factory Default
- 52 Reboot
- 52 Logout
- 54 Advance Setup
- 54 Internet Mode
- 54 Internet Setup
- 54 AP
- 54 WiFi AP
- 54 WiFi ISP
- 54 IP Config
- 54 WAN
- 54 PPPoE
- 56 DHCP
- 56 Static IP
- 57 PPTP
- 59 L2TP
- 60 3.5G
- 61 Smartphone
- 62 LTE
- 64 LAN
- 65 DDNS
- 66 IPv6 Config
- 68 Wireless
- 68 Basic Settings
- 70 Advanced Settings
- 71 Security
- 73 Access Control
- 73 WPS
- 75 WDS
- 79 Schedule
- 79 NAT
- 79 DMZ
- 79 Virtual Server
- 81 AirCloud Storage
- 81 AirCloud Monitor
- 81 VPN Server
- 81 Firewall
- 81 DoS
- 82 5.5.2 QoS
- 83 Port Filtering
- 84 IP Filtering
- 84 Mac Filter Schedule
- 84 URL Filtering
- 84 IP Binding
- 84 VLAN
- 85 System
- 85 Wake on Lan
- 86 Change Password
- 86 Firmware Upgrade
- 86 Profiles Save
- 89 Remote Management
- 89 Time Zone
- 89 UpnP
- 90 Route Setup
- 92 VPN Passthough
- 92 Wan Type Auto Detection
- 94 Q & A
- 94 Installation
- 94 LED
- 94 IP Address
- 95 OS Setting
- 97 GR297N Setup
- 98 Wireless LAN
- 100 Support
- 101 Others
- 102 Appendices
- 102 Operating Systems
- 102 Browsers
- 102 Communications Regulation Information