Bosch HBN 5405.0 A Technical data

BOSCH
INSTALLATION INSTRUCTION' MANUAL
for
Bosch Electric Built-in
Single & Double Oven Models HBN 64.J65,.166.,
BEFORE YOU BEGIN, READ THESE
INSTRUCTIONS
COMPLETELY
AND CAREFULLY
IMPORTANT:
Save these instructions for _e local electrical inspector's nse'_
INSTALLER:
Please leave this manual w_th owner for future reference.
|
OWNER: Please keep this manual for future reference
/
J
Table of Contents
INTRODUCTION
.............................................................................................................................
Tools You Will Need ...................................................................................................................
3
Power
3
Requirements
Choosing
.............
Oven Location
Steps for Installation
TECHNICAL
.........
.............................................................................................................
3
....................................................................................................................
3
DATA ....................................................................................................................
[....
4
Single
oven ...................................................................................................................................
4
Double
oven ..................................................................................................................................
4
UNDERCOUNTER
SINGLE
WALL
INSTALLATION
INSTALLATION
WIRING
...............................
OVEN .........................................................................................
A
L SUPPLY
REQUIREMENTS
CONNECTING
ELECTRICAL
..................................................................................
OVEN ............................................................................................................................
DOUBLE
(ELECTRIC
.i
..........................................................................................
OVEN ............................................................................................................................
SINGLE
.
,.
,.°,***°°,,
......................................................................................................
TO 208 VOLT
CONNECTIONS
......
. ...........
.................................
CIRCUIT
.. ...........................
:.................................................
.................................................................
3-WIRE
BRANCH
CIRCUIT ..............................
4-WIRE
BRANCH
CIRCUIT .....................................................................................................
FINAL
2
,
CHECKLIST
........................................................................................................................
5
5
6
6
7
8
8
9
10
10
11
INTRODUCTION
Please
read
these
instructions
COMPLETELY
AND CAREFULLY.
They will save you time .and
effort and help to ensure optimum oven performmace. Be sure to observe all WARNINGS.
These
installation
instructions
are
• use by a qualified installer. In addition
structions the oven shall be installed:
int_ndad
for
to these in-
• In the United States, in accordance with the National Electric Code/State
and Municipal codes
and/or local codes.
• In Canada,
tric Code
in accordance
with Canadian
C22.1-1ateSt
edition/Provincial
Municipal
codes
followed
at all times.
If installing your oven in Canada please
check tO make sure that you have a model
with the UL Canadian
listing mark, as
shown below:
The UL Canadian listing mark consists of the circled UL symbol preceded
by the letter "C", as
showm This should appear on the oven's rating
plate along with the UL United
States listing
mark, which is the circled UL symbol above but
not preceded by the letter "C".
TOOLS
YOU
The following
WILL
tools "are needed to install your new
and straightedge
screwdriver
• Level
• Wire cutters
and wire stripper
• I" hole saw
• Hand or saber saw.
POWER
CHOOSING
OVEN
LOCATION
Carefully select the location where the oven will
be placed. The oven should be located for convenient use in the kitchen,
but away from strong
drafts. Strong drafts may be caused by open doors
or windows, or by heating and/or air conditioning
vents or fans. Make sure that electrical power can
be provided to the location selected.
STEPS
FOR
INSTALLATION
.'
The following pages provide the necessary information for proper installation
of the oven arranged as follows:
• Technical
Data
Cutout
Dimensions,
and Mounting instructions
> Undercounter
Installation,
Single
>Wall Installation,
Single Oven
>Wall Installation,
Double
Required
for:
Oven
or ruler
• Pencil
• Phillips
It is recommended that you have the electrical
wiring and hook-up of your oven performed by a
qualified elcc_iciam After installation is comflete have the electrician show you where the
main disconnect is and which of the circuit breakers/fuses are for the oven.
• Installation
Clearances
NEED
oven:
• Tape measure
The oven must be supplied with copper wires
ONLY.
and/or local codes.
The,_ shall be carefully
Note:
Elecand
•,aT208 volt circuit must be used, wiring inside the
oven must be modified. See Connection
to a 208
Volt Circuit, in this manuai. A circui[ breaker or
time-delay
fuse sized not to exceed the circuit rating of the appliance specified on the rating plate
located on the frame behind the door of the oven
is recommended.
REQUIREMENTS
The oven must be supplied with the proper voltage and frequency.
The oven is manufactured
to
be connected
to a three wire or four wire, single
phase, 240 volt, 60 Hz AC electrical supply on a
separate, circuit fused on both sides of the line. If
• Electrical
Oven
Supply and Wiring
• Modifications
Volt Circuit.
required
• Electrical
Connections
B'ranch Circuit.
• Final Checklist.
Requirements
if Connecting
for
3-wire
to 208
or
4-wire
TECHNICAL
SINGLE
DATA
OVEN
For cutout dimensions
Preparing
see following
sections titled:
Location
Single Oven
Models
Electrical Ratings
and Maximum Connected
Load
Convection
Oven
Hertz
Amperes
@240V/208V
Watts
@240V/208V
HBN 642A UC 240/208
60
13.1/13.3
3,150/2,775
Yes
HBN 645A UC 240/208
60
13.1/13.3
3,150/2,775
Yes
HBN 646A UC 2401208
60
13.1/13.3
3,150/2,775
Yes
DOUBLE
Volts
OVEN
For cutout dimensions
Preparing
sec following
sections titled:
Location
Double Oven
Models
Electrical Ratings
and Maximum Connected Load
Convection
Oven
(_p_ot_m)
Hertz
Amperes
@240V/208V
Watts
@240V/208V
HBN 652A UC 2401208
60
26.3/24.8
6,300/5,150
Yes/No
HBN 655A UC 240/208
60
26.3/24.8
6,300/5,150
Yes/No
[-IBN 656A UC 240/208
60
26.3/24.8
6,300/5,150
Yes/No
HBN 662A UC 240/208
60
26.3/24.8
6,300/5,150
Yes/Yes
HBN 665A UC 240/208
60
26.3/24.8
6,300/5,150
Yes/Yes
HBN 666A UC 240/208
60
26.3/24.8 6,300/5,150
Yes/Yes
4
Volts
UNDERCOUNTER
--
INSTALLATION,
SINGLE
m
L
I
O_n elec_l_ supply:
LocateJun_onboxIn
_lJa_mt cabinetor below
bottomsupportsurface.
I
I
I
!
I
I
_"
I
openingwidth
'1
I
Bottom supper sud_,e must
be solid, le_i_ and able to
supper at least of 150 Ibs.
\
I
I
I
114"min. distance
b_'ween ovln door
frme md -,,'jas*nt
_ doom or dmw_ fron'=
F-toe spa_
anm
2e.._" ._flh of oven do_- frame
maintain minimum spadng u ahown.
Secure oven to cabinet using 1he
prodded, Screws should be _
_lrOUgh
rnoun_g holes In 1he _
Indicted |n I_
frame (o-r_mdoor to ase frame and mounting
bolas). Do notove_ghten sa_ws.
Note: Decorsthteinserts must
maintain minimum spacing as shown.
Refer to and follow Notes and Warning
listed under Wall Installation,
Single
Oven (facing
page)
WALL
INSTALLATION,
SINGLE OVEN
Secureoven to cabinet uSklgthe screws
movlded. Screws should be Inserted
.= Ihrough the mountln_ holes In _e
posi_ora _ldicat_d in me frame (o_m
! doorto see flame and mounlJngho_esI.
Donot ov_tighten screws.
Nnte:
Do not slide oven across floor. Damage to floor covering or floor could result.
.
The oven support surface must be a
minimum
3/4" thick plywood
platform, solid, level and flush with the
bottom of the cabinet cutout.
.
.
4
Use extreme caution when moving
installing the oven. It is very heavy.
or
Be very careful when moving or installing the oven to avoid damage to
the oven frame or damage to the cabinets.
.
6. Be careful when placing
oven. DO
NOT pinch the conduit between
the
oven back or wall and the inner cabinet wall or floor.
Be sure to level oven. An oven that is
not level may provide poor or inconsistent baking results.
%
Securely
fasten oven to cabinet
using the
screws provided. Failure to do so could result
in oven moving or tipping during use and
causing damage to the oven or cabinets or personal injury.
WALL
INSTALLATION,
DOUBLE
OVEN
Secure oven to cabinet using the screws
provided. Screws should be inserted
through the mounting holes in the
positions indicated in the frame (open
door to see frame and mounting holes).
Do not overtightan screws,
Note:
Do not slide oven across floor. Damage to floor covering or floor could result.
.
The oven support surface must be a
minimum
3/4" thick plywood
platform, solid, level and flush with the
bottom of the cabinet cutout.
3. Use extreme caution when moving
installing the oven. It is very heavy.
or
4. Be very careful when moving or in-,
stalling the oven to avoid damage to
the oven frame or damage to the cabinets.
.
Be sure to level oven.
not level may provide
sistent baking results.
6. Be careful when' placing
oven. DO
NOT pinch the conduit
between
the
oven back or wail and the inner cabinet wall or floor.
An oven that is
poor or incon-
Securely
fasten oven to cabinet
using the
screws provided. Failure to do so could result
in oven moving or tipping during use and
causing damage to the oven or cabinets or personal injury.
ELECTRICAL
SUPPLY
Before installing the oven have a qualified electrician verify that your home is provided with adequate electrical service and that the addition of
the oven will not overload the branch circuit on
which it is to be installed. A separate three-wire
or four-wire single phase, 240 Volt, 60 Hz., or a
208 Volt, 60 Hz. branch circuit is required.
Note:
For use with 208 V, 60 Hz supply voltage
the wiring must be modified as shown in
Connecting to 208 Volt Circuit.
WIRING
When making the wire connections, use the entire
length of the conduit provided (3 fee0. The conduit must not be cut.
Before making connections make sure the power
is off and read and observe the following:
1.
A. separate three-wire or four wire, single
phase, 240 Volt, 60 Hz. or 208 Volt, 60 Hz
branch circuit is required for the oven.
The oven must be connected with COPPER
WIRE ONLY.
.
3.
In the United States:
Wiring must conform to the National Electrical Code, ANSI/NFPA
No. 70 latest edition.
You can obtain a copy of the National Electrical Code by writing:
National Fife Protection Association
For hook-up of the oven you will need to have an
approved junction box installed where it will be
easily reached
through
the front of the cabinet
where the oven will be located. The oven has 3
feet of conduit. Allow two to three feet of slack in
the line so that the oven can be moved if servicing
is ever necessary.
DO NOT shorten the flexible
conduit.
B atterymarch Park
Quincy, MA 02269
• Electrical
ground is required on this appliance. The free end of the green wire (the
ground wire) must be connected
to a suitable ground.
This wire must remain
grounded
to the
Canadian Standards Association
178 Rexdale Boulevard
Rexdale (Toronto), Ontario, Canada
M9W 1R3
Wire size (COPPER WIRE ONLY) and connections must be suitable for the rating of the
appliance per the National Electrical Code
requirements. The flexible armored cable extending from the oven should be connected
directly to the junction box.
.
The junction box should be located so as to
allow as much slack as possible between the
junction box and the oven so it can be moved
if servicing is ever required.
.
oven.
• If cold water pipe is interrupted
by plastic,
non-metallic
gaskets, union connections
or
other insulating materials,
DO NOT use for
grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the NEUTRAL
or
GROUNDING
circuit. A fuse in the NEUTRAL or GROUNDING
circuit could result
in an electrical shock.
• Check with a qualified electrician if you are
in doubt as to whether
the appliance
is
properly grounded.
Failure to follow these instructions
could result in serious injury or death.
8
..
In Canada:
W'tring must conform to Canadian Electrical
Code C22.1- latest edition. You can obtain
copies of the Canadian Electrical Code by
writing:
ELECTRICALSHOCKHAZARD
• The electrical power to the oven branch circuit must be shut off while line connections
are being made.
• Do not use an extension cord with this appliance.
REQUIREMENTS
.
A U.L. listed conduit connector must be provided at each end oftbe power supply cable.
CONNECTING
To connect to 208 volt circuit:
TO 208 V CIRCUIT
The ovens are pre-wired for connection
to 240
volt, 60 Hertz supply. If connecting
to a 208 volt,
60 Hz. supply a jumper must be used across, two
terminals.
For the double oven models ther'e are
two jumpers, one for the upper oven and one for
the lower oven. For the single ovens there is one
jumper.
Please refer to figures below for placement
jumper for 208 volt, 60 hertz connection.
1
.
Remove the access panel(s) lQcated on the
back of the oven(s).
Loosen the first and second screws in the terminal block as shown in applicable figure
above.
3.
Place the metal jumper between the first
and second screws and tighten screws to
hold jumper in place.
4.
Replace
of
access panel(s).
Placing of jumper for single oven
or upper oven of double oven,
for connection to 208 volt, 60 Hz.
B_om
Jumper
After
JL_nper
Placing of jumper for lower oven
of double oven, for connection to
208 volt, 60 Hz.
Before
Jumper
After
Jumper
ELECTRICAL
CONNECTIONS
3-WIRE
This appliances is manufactured
with a green
GROUND wire connected to the oven chassis.
After making sure that the power has been turned
off connect the flexible conduit from the oven to
the junction box using a U.L. listed conduit connector. Figures A and B and the instructions provided below present the most common way of
connecting the ovens. Your local codes and ordinances, of course, take precedence to these instructions. Complete electrical connections according to local codes and ordinances.
,klncSon I_x
Redwlr_,_
BRANCH
Refer to Figure A, where local codes allow the
connection of GROUND wire from the oven to
the branch circuit NEUTRAL wire (grey or white
colored wire):
• If local codes permit, connect the green
GROUND wire from the oven and the white
wire from the oven to the branch circuit NEUTRAL wire (grey or white colored wire).
• Connect the red and black leads from the cooktop to the corresponding leads in the junction
box.
allb_ from
_
Grounded Neut_l
B
_
Immo,_m
Figure
4-WIRE
Refer
BRANCH
to Figure
CIRCUIT
CIRCUIT
B:
• Connect
the green GROUND
wire from the
oven to the GROUND
wire in the junction box
(bare or green colored wire).
U.L-kded
_
€ondtdt connector
A.
". Connect the red and black leads from the oven
to the corresponding leads in the junction box.
• Connect the white wire from the oven to the
NEUTRAL (grey or white) wire in the junction
box.
_Ungrounded
Neutral
Black wlr_
Cable
from oven
Figure B.
lO
U.L-_ed
conduit connector
.
FINAL
CHECK LIST
you have modified the oven(s) for use on 208
volt the voltage reading between the black
and red wires should be 190 to 208 volts.
To prevent improper connections
leading to damage of electrical components and so voiding the
warranty, the following steps must be performed:
Set the time of day by pressing the Set
Clock button and pressing the plus (+) or minus (-) button, to the right of the display to
set the correct time. Once the time is set depress the Set Clock button to enter the time.
A "beep" will sound and the Set Clock symbol in the upper right wiU disappear.
.
Check the electrical
requirements
and make
sure you have the correct elec_ical
supply
and that the oven is properly grounded.
,
.
3.
Make sure all control
sition.
knobs are in the off po-
Turn the Mode Selector knob to Manual position, the Selector knob to Bake and turn the
Temperature
knob to 350 *F. The cooling
fan, the oven lights and the heat light should
come on to indicate that the oven is heating.
The heat light will turn off when the set temperature (350 *F),is reached. Turn Temperature knob to off. If you have installed a double oven repeat test for second oven.
.
Turn on the power supply to the oven. When
the oven is first turned on the display will
come on showing all the call-outs and then
will become blank with the Set Clock symbol in the upper fight corner, as shown below.
SET
.
To check
the other
oven
functions
the Using the Oven Controls
Use and Care Manual.
section
refer
to
of the
8.
4.
Check power at the jtmetion box wires using
a volt meter having a range of 0-250 VAC. If
you have installed the oven for use on 240
volt supply you should find that the voltage
reading
between
the black and red wires
(Line to Line) should be 220 to 240 volts. If
If the oven is working properly turn the Selector knob(s) and the Temperature Control
knob(s) to their off positions and press in the
knobs so that they are flush with the oven
and turn off the power supply to the oven.
9. Place the cover on the junction box and
make sure the cover is securely fastened and
turn on the power to the oven.
10. Leave these INSTALLATION
instructions
as well as the USE AND CARE MANUAL
with the owner.
11