Vibe Space 12 D4 Specifications

PHONES
(044) 360-7-130
(050) 336-0-130
(063) 788-0-130
(067) 233-0-130
(068) 282-0-130
Internet store of
autogoods
ICQ
294-0-130
597-0-130
SKYPE
km-130
CAR RECEIVERS — Receivers • Media receivers and stations • Native receivers • CD/DVD changers • FM-modulators/USB adapters • Flash memory • Facia plates and adapters • Antennas • Accessories |
CAR AUDIO — Car audio speakers • Amplifiers • Subwoofers • Processors • Crossovers • Headphones • Accessories | TRIP COMPUTERS — Universal computers • Model computers • Accessories |
GPS NAVIGATORS — Portable GPS • Built-in GPS • GPS modules • GPS trackers • Antennas for GPS navigators • Accessories | VIDEO — DVR • TV sets and monitors • Car TV tuners • Cameras • Videomodules
• Transcoders • Car TV antennas • Accessories | SECURITY SYSTEMS — Car alarms • Bike alarms • Mechanical blockers • Immobilizers • Sensors • Accessories | OPTIC AND LIGHT — Xenon • Bixenon • Lamps
• LED • Stroboscopes • Optic and Headlights • Washers • Light, rain sensors • Accessories | PARKTRONICS AND MIRRORS — Rear parktronics • Front parktronics • Combined parktronics • Rear-view mirrors
• Accessories | HEATING AND COOLING — Seat heaters • Mirrors heaters • Screen-wipers heaters • Engine heaters • Auto-refrigerators • Air conditioning units • Accessories | TUNING — Vibro-isolation
• Noise-isolation • Tint films • Accessories | ACCESSORIES — Radar-detectors • Handsfree, Bluetooth • Windowlifters • Compressors • Beeps, loudspeakers • Measuring instruments • Cleaners • Carsits
• Miscellaneous | MOUNTING — Installation kits • Upholstery • Grilles • Tubes • Cable and wire • Tools • Miscellaneous | POWER — Batteries • Converters • Start-charging equipment • Capacitors
• Accessories | MARINE AUDIO AND ELECTRONICS — Marine receivers • Marine audio speakers • Marine subwoofers • Marine amplifiers • Accessories | CAR CARE PRODUCTS — Additives • Washer fluid •
Care accessories • Car polish • Flavors • Adhesives and sealants | LIQUID AND OIL — Motor oil • Transmission oil • Brake fluid • Antifreeze • Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in
Kyiv and other cities, delivery by ground and postal services. Our experienced
consultants will provide you with exhaustive information and help you to chose
the very particular thing. We are waiting for you at the address
http://130.com.ua
a
u
.
m
o
c
.
0
3
1
������������������
To ensure maximum performance and safety,
please follow this manual. Please retain the
manual for future reference after installation
�����������������������
Autogood products Internet store “130”
�������������
�����������������������
Congratulations on purchasing your VIBE Space subwoofer. Please read this manual in order to fully understand how to get the
best results from your subwoofer and ensure that all advice on how to look after the Subwoofer is followed.
Thank you for buying VIBE. We hope you enjoy listening to your product as much as we enjoyed creating it.
VIBE R&D Division
����������������
All VIBE products carry a full twelve months warranty period, valid from
the date of the original receipt and proof of purchase. In order to
validate this warranty, the warranty card should be returned to VIBE
within seven days of the original purchase date. The original receipt
and packaging are should also be retained for this twelve month period.
If at any stage during the warranty period you have a problem with the
product then it should be returned to the point of purchase, in its
original packaging, complete with no items missing.
a
u
.
m
o
If the store is unable to fix the product it may have to be returned to VIBE
This process takes around 7 working days and no costs will be
occurred.
A full description of VIBE's warranty information can be found on our
website:
c
.
0
����������������������������
3
1
A written version can also be obtained from
VIBE warranty Dept
What is not covered.
●
●
●
●
●
●
●
●
●
●
Damage to product due to improper installation
Subsequent damage to other components
Damage caused by exposure to moisture, excessive heat, chemical cleaners and/or UV radiation
Damage through negligence, misuse, accident or abuse, repeated returns for the same fault may be considered abuse
Any cost or expense related to the cost of removal or re-installation of the product
Damage caused by amplifier clipping or distortion
Items repaired or modified by any unauthorized repair facility
Return shipping on non defective items
Products returned without a returns authorization number
Damage to product due to the use of sealant
International warranty
Contact your international Vibe audio dealer or distributor concerning specific procedures for your country’s warranty policies
.
Warning
Vibe subwoofers are capable of sound pressure levels that can cause permanent damage to your hearing and those around you,
please use common sense when listening to your car audio system and Practice safe sound.
2
Autogood products Internet store “130”
Run in procedure
VIBE recommends that you follow the run in procedure for the subwoofer detailed below.
When your Subwoofer is used for the first time, like most brand new items it is naturally very stiff and rigid. It will take time for
the moving parts of this Subwoofer to loosen up before the Subwoofer will be ready to deliver its full potential.
For the first 30 hours it is recommended that you play the Subwoofer initially at low to medium volumes, gradually increasing the
volume level as time progresses.
As a guide, if you listen to your Subwoofer for 1 hour every day it will take a month for the subwoofer to run in properly.
You will notice a big change in the sound of the Subwoofer over this period. As the spider and surround begin to run in the sound
will get deeper and harder, also the output of the Subwoofer will increase as the suspension loosens up.
The Subwoofer is like your car’s engine, it needs a few thousand miles before you can drive it to its full potential. Driving it into the
redline from the first day will mean engine damage is certain and will not be covered by warranty.
Failure to follow this simple procedure is the most common reason for a Subwoofer to fail after a very short period of time.
Wiring options
The Space subwoofer has a dual 2 ohm or 4 ohm voice coil. Below are a few different wiring examples, please check with your
amplifier manufacturer as to which wiring method is most suitable.
The Space subwoofer terminal included 2 bridging clips to make coverting the wiring from series to parallel easy.
Please see the diagram below for wiring examples.
a
u
.
m
o
single woofer configuration
Space 12 D2
Space 12 D2
c
.
0
Space 12 D4
Space 12 D4
3
1
1 Ohm - parallel wiring
4 Ohm - series wiring
2 Ohm - parallel wiring
Autogood products Internet store “130”
8 Ohm - series wiring
3
Twin woofer configuration
4 Ohm - series / parallel wiring
2 Ohm - series / parallel wiring
a
u
.
m
o
Installation
The Space subwoofer can be installed in a variety of different ways, the most suitable will depend upon your application.
Free-air installation
c
.
0
The VIBE Space Subwoofer can be mounted free-air, but this does not mean that the woofer can work without any form of
enclosure. What it does mean is that the enclosure can be very large and therefore the subwoofer can utilise the vehicles boot as an
enclosure.
The Subwoofer needs to be mounted to a rigid panel as excess vibration will result in poor sound quality. The panel or baffle, should
also seal the output from the front of the Subwoofer from the output from the rear otherwise poor sound quality, known as phase
error, will occur. This simply means that the output from the rear of the woofer will cancel out the output from the front resulting in a
loss of bass.
As the enclosure in free-air applications is so large it is worth noting that the power handling of the Subwoofer is reduced to half that
of the same woofer in a measured enclosure. Please take this into account when choosing your amplifier.
The sound quality of a free-air mounted Subwoofer will not match that of the same subwoofer mounted in a measured enclosure.
However in applications where building a traditional enclosure is impossible, free-air mounting will add increased bass response to
your system.
3
1
4
Autogood products Internet store “130”
Sealed enclosure installation
The most basic and simple of all speaker enclosures is the sealed enclosure otherwise referred to as an acoustic suspension
design. They are called acoustic suspension enclosures because the air inside the box acts like a brake to control the woofer.
The sealed enclosure is the easiest design to build and tune, as long as you work within the minimum and maximum
recommended volumes you cannot get it wrong. The smaller enclosures produce a tighter punchy bass, the larger enclosures
produce a deeper bass. Sealed enclosures offer high power handling, tight response and smooth low end roll off and cone
motion is better controlled at all frequencies because of the constant pressure on the back of the woofer.
Sealed enclosures are ideally suited to rock, jazz and live music.
PRODUCT
Space
12
TIGHT BASS
1.0 cu.ft
DEEP BASS
2 cu.ft
a
u
.
m
o
For twin enclosures simply double the volume. E.G. 2 x Space 12 in deep bass enclosure will be 4.00cuft
c
.
0
Ported enclosure installation
A ported or vented enclosure is not much more complex than a sealed design. It consists of a box with a hole in it.
The vented enclosure has to be correctly designed in order to function correctly. The vent in the enclosure interacts with the air
in the cabinet and the woofer to increase output and reduce cone excursion at and around the tuning frequency.
At the tuning frequency of the enclosure almost all of the bass is being produced by the vent, not the woofer. It is more difficult to
achieve good performance as the enclosure volume and port volume are critical but the results are worth it as the ported box is
up to 3 times as loud as the same woofer in a sealed box. It is also possible with the correct tuning to add a “bump” in the
response of the enclosure to boost bass at a preferred frequency. Vented enclosures are best suited to dance, R&B,
electronically produced music and high SPL applications.
3
1
PRODUCT
VOLUME
Space
2 cu.ft
12
PORT
2 x 3” ports, 6” length
For twin enclosures simply double both the volume and the porting. E.G. for 2 x Space
12 the enclosure will be 4cu. ft with 2 x 4” ports
Many other ported options exist, please contact VIBE for more information
Autogood products Internet store “130”
5
Enclosure construction
a
u
.
m
o
Enclosure Volume
To work out the volume required for your enclosure please refer to recommended enclosure volumes specified for your
Subwoofer. These are listed in cubic feet. To convert cubic feet to litres multiply the cubic feet by 28.3. If you use this formula
calculating your enclosure size will be easy .1 cubic foot is expressed as 12” x 12” x 12” = 1728 cubic inches
c
.
0
3
1
6
Autogood products Internet store “130”
If we require a volume of 2.5cuft then we multiply this by 1728 2.5 x 1728= 4320 cubic inches.
We now take 2 known enclosure dimensions that we will use, e.g height and width and divide this figure by them which will give us
the depth, for example our height is 15”, our width is 20”.
So our depth is 14.4” for this enclosure.
Note : this formula is for the INTERNAL dimensions, please add the thickness of the material used to construct the enclosure to
the formula to give you the outside dimensions.
a
u
.
m
o
So assuming we are using 1 inch material we need to add 2 thicknesses to each internal dimension to allow for material top and
bottom, so the external dimensions for this enclosure would be 17 x 22 x 16.4 inches.
c
.
0
The displacement of the woofer and the displacement of the port must also be added to the required volume before you calculate
the required sizes needed to build your enclosure.
3
1
NOTE- When using a port you must leave a gap at least equal to the shortest measurement of the port between the rear of the
enclosure and the port.
Autogood products Internet store “130”
7
a
u
.
m
o
c
.
0
3
1
Copyright
All content included in this manual such as text, graphics, logos, icons, images and data, are the property of VIBE Technologies Limited (herein referred to as "VIBE", "us" or "we") and its
affiliate or their content and technology providers, and are protected by United Kingdom and International copyright laws. All rights reserved.
VIBE Turbo Port, Vibe TurboVent, Pressure Board, Super Driver, VIBE Pulse, VIBE Power, VIBE Digital, VIBE MAG Plugs, Ferrite Loaded, VIBE Solid Core, VIBE OCC, VIBE FLAT,
BlackAir, BlackBox, Space, MonoBox, SA-K, SR, QB69, ICC, Bass Enhance, Bass Enhance+, QBass, SpeedBass, PowerBass and all stylised representations of product names, or the
abbreviations of product names, as logos are all trademarks of VIBE. Graphics and logos are trademarks or trade dress of VIBE Technologies Ltd or its subsidiaries.
VIBE's trademarks and trade dress may not be used in connection with any product or service that is not VIBE's, in any manner that is likely to cause confusion among customers or in any
manner that disparages or discredits VIBE. All other trademarks not owned by VIBE or its subsidiaries that appear in this manual are the property of their respective owners, who may or
may not be affiliated with, connected to, or sponsored by VIBE or its subsidiaries.
TO THE FULLEST EXTENT PERMITTED AT LAW, VIBE IS PROVIDING THIS MANUAL AND ITS CONTENT ON AN "AS IS" BASIS AND MAKES NO (AND EXPRESSLY DISCLAIMS
ALL) REPRESENTATIONS OR WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WITH RESPECT TO THIS MANUAL OR THE INFORMATION, CONTENT, MATERIALS OR
PRODUCTS INCLUDED IN THIS MANUAL INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IN ADDITION, VIBE DOES NOT REPRESENT OR WARRANT THAT THE INFORMATION CONTAINED IN THIS MANUAL IS COMPLETE OR CURRENT, AND THAT ALL
SPECIFICATIONS AND INFORMATION CONTAINED WITHIN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE.
VIBE RECOMMEND CAUTION WHEN LISTENING TO MUSIC REPRODUCED THROUGH VIBE EQUIPMENT. VIBE EQUIPMENT IS CAPABLE OF PRODUCING SOUND AND SOUND
PRESSURE LEVELS THAT CAN PERMANENTLY DAMAGE HEARING OF YOU AND THAT OF OTHERS. FOR SAFE AND ENJOYABLE LISTENING, THE SOUND SHOULD BE CLEAR
WITHOUT DISTORTION AT A COMFORTABLE VOLUME.
BY USING ANY VIBE EQUIPMENT, YOU AGREE TO TAKE FULL RESPONSIBILITY FOR YOUR OWN SAFETY AND THE SAFETY OF OTHERS WHEN LISTENING TO MUSIC AT
HIGH VOLUMES THROUGH EQUIPMENT YOU HAVE PURCHASED. USE OF ANY VIBE EQUIPMENT CONSTITUTES AGREEMENT TO THIS DISCLAIMER.
Except as specifically stated in this manual, to the fullest extent permitted at law, neither VIBE nor any of its affiliates, directors, employees or other representatives will be liable for damages
arising out of or in connection with the use of this manual or the information, content, materials or products included.
This is a comprehensive limitation of liability that applies to all damages of any kind, including (without limitation) compensatory, direct, indirect or consequential damages, loss of data,
income or profit, loss of or damage to property and claims of third parties. For the avoidance of doubt, VIBE does not limit its liability for death or personal injury to the extent only that it
arises as a result of negligence of VIBE, its affiliates, directors, employees or other representatives.
8
Autogood products Internet store “130”
Parameters for Space 12 D2 / D4
RMS power
Peak power
Min, Input wattage
Diameter in inches
Z- Nominal Impedance in Ohms
Revc = DC voice coil resistance in Ohms
Fo = Free air resonance frequency in Hz
Sd = Piston area in square meters
Vas = Equivalent acoustic volume in cubic litres
Cms = Mechanical suspension compliance
Mmd = Diaphram mass in grams
Mms = Mechanical mass of cone and free air load in grams
BL = The magnetic strength of the motor structure
Qms = Mechanical Q factor of driver
Qes = Electrical Q factor of driver
Qts = the system’s Q at resonance (Fc)
n0 = The reference efficiency of the system in %
SPL = Speaker’s SPL 1 watt at 1meter in dB:
Voice Coil Diameter in inches
Mounting Depth in mm
Mounting Diameter in mm
Magnet weight in oz
Space 12
1000
3000
500
12”
Dual 2 Ohm / Dual 4 Ohm
3.9
30
53
39.21
0.113
232
238.5
16.13
6.322
0.547
0.504
0.2
88
3
170
285
120
a
u
.
m
o
In order to protect your purchase and aid your
warranty please fill in the following form and
keep it safe for your future reference:
c
.
0
3
1
Model Number:
Serial Number:
Purchased From:
KEEP IT SAFE
Staple your receipt here:
Date of Purchase:
Autogood products Internet store “130”
9
a
u
.
m
o
c
.
0
3
1
Autogood products Internet store “130”
FLATBASS™ 13 SPK Bass speaker cable
There are many powerful bass amplifiers on today’s market – the ever increasing power is putting huge strains on speaker wire
– VIBE present a new breed of speaker cable specially developed for BASS applications – the VIBE FLATBASS speaker cable
offers SolidCores™ that can handle and sustain considerably more power than conventional speaker cable.
Model: FlatBass 13 SPK – 13 gauge SolidCore™ flat BASS speaker cable
VIBE 140 amp circuit breaker
Big systems require big protection – The VIBE circuit breaker is rated at a massive 140 amps and offers critical protection to
your system – if the system over powers or short circuits the breaker will cut in and save your equipment. No need to replace
expensive fuses, system is reset via a simple switch – also offers safe and instant system shutdown.
Model: CB140 – 140 amp circuit breaker
FLAT Y 2M / FLAT Y 2F RCA Y leads
Our professional quality full range OFC Y-interconnect guarantees a pure and strong signal. With a flat
design and ferrite loaded gold plated plugs interference is greatly reduced. The FLAT-Y Interconnect is
available in 1 male – 2 female FLAT Y 2F and 2 male – 1 female FLAT Y 2M configurations.
Model: FLAT Y 2f – 1 pair RCA Y lead 1male to 2 female
Model: FLAT Y 2m – 1 pair RCA Y lead 2male to 1female
VIBE BC10 level controller
The VIBE BC10 gain level controller is a perfect addition to any subwoofer system, the BC10 allows the level of the amplifier to be
controlled from the driver’s seat giving the user easy adjustment of gain level. Particularly useful for adjusting the gain level for
amplifiers controlling subwoofers. The BC10 controller is RCA input and output making it compatible with any system allowing gain
level adjustment of any amplifier it is connected to. It can also be used with full range amplifiers.
Model: BC10 – RCA Gain level control
Slick level remote
A new addition to the Slick range of amplifiers is the Slick level control which allows level adjustment of the amplifier from the front of
the car - Simply plug the supplied cable into the Slick remote level port on the end panel of the amplifier and remote gain control is
yours, it is that easy.
Model: SLR1 – optional remote for use with all Slick amplifiers
VIBE PortPlug™
The VIBE PortPlug allows easy tuning of the VIBE CBR bass enclosures. The PortPlug™ is used to tightly
seal the VIBE TurboPort™ in the enclosure to either create a sealed enclosure for better transient
response or in the case of a multi ported enclosure re-tune the enclosure using only 1 PortPlug™
Model: PP25 – PortPlug™ for 2.5” TurboPort™
Model: PP30 - PortPlug™ for 3” TurboPort™
a
u
.
m
o
VIBE official Merchandise
MPS – VIBE polo shirt with embroidered VIBE logo on front and rear
MTS – VIBE T-shirt with small VIBE printed logo on front.
MCD – VIBE CD, containing exclusive VIBE bass tracks as featured on the Bass Tunnel and VIBE Dredd.
MCC – VIBE CD case, metallic silver CD case with VIBE logo.
VFL – VIBE fleece with embroidered logo on the front and large on back.
VTD – VIBE tax disc holder, stylish silver tax disc holder featuring VIBE logo.
VIBE SD4/5 subwoofer defender grill
The new VIBE subwoofer defender not only provides protection for your sub but also adds style with its metallic
badge and black rubberised steel construction allow it to integrate perfectly with the VIBE EVO enclosures
Model: SD4 – sub grill fits both 10” and 12” subwoofers
Model: SD5 – sub grill fits 15” subwoofers
c
.
0
3
1
VIBE GB41 banana plug
The VIBE GB41 banana plugs are the easy and convenient way to quickly remove your bass enclosure without
having to constantly re-thread your speaker cable into the box terminal, simply attach the speaker cable to the
VIBE GB41 banana plug and you have a reliable quick release solution. Designed for optimum use with the TP-2
and QP-4 terminal, our professional gold plated 4mm banana plugs are polarity marked and feature rubber
shrouds.
Model: GB41 – Gold Banana plug
VIBE DB6 non fused distribution block
The VIBE DB6 non fused distribution block is a professional non fused distribution block which gives easy
connection for up to 5 amplifiers. The VIBE DB6 has 2 x 4AWG input and 4 x 8AWG outputs which can be
used for power distribution or ground distribution giving a common grounding point for all system
components eliminating the risk of ground loop interference.
Model: DB6 non fused distribution block
VIBE FD4 fused distribution block
The VIBE FD4 fused distribution block is a professional AGU fused distribution block which gives easy
connection for up to 4 amplifiers. The VIBE FD4 has 1 x 4AWG input and 4 x 8AWG outputs each
individually fused up to a maximum of 80 amps (AGU fuses available separately)
Model: FD4 – 4 way AGU fused distribution block, 1 x 4 gauge input 4 x 8 gauge outputs
VIBE CT0 / CT4 compression fit ring terminal
The VIBE CT range of gold plated ring terminals are professional compression fit designed for maximum
conductivity when connecting power cable to the vehicle battery. The VIBE RT compression fit terminals are
the best way to connect heavy gauge power cable to the vehicles battery.
Model: CT0 – 0 gauge compression fit ring terminal
Model: CT4 – 4 gauge compression fit ring terminal
VIBE RT4 / RT8 crimp on ring terminal
The professional range of VIBE RT gold plated ring terminals for connecting power cable to the vehicle
battery. Packed in pairs and include red and black rubber over boots with are easy crimp design.
Model: RT8 – 1 pair of 8 gauge crimp on ring terminals with PVC overboots
Model: RT4 – 1 pair of 4 gauge crimp on ring terminals with PVC overboots
VIBE AGU30, AGU60, AGU80 fuses
The VIBE AGU fuse series are the perfect companion to the VIBE FD4 fused distribution block and the Active
and stereo system wiring kits.
Model: AGU30 – 1 pair 30 amp AGU fuses to fit all AGU fuse holders
Model: AGU60 – 1 pair 60 amp AGU fuses to fit all AGU fuse holders
Model: AGU80 – 1 pair 80 AGU fuses to fit all AGU fuse holders
All Accessories are available direct, for next day delivery call 0870 765 8423
For more product info see www.vibeaudio.co.uk
Autogood products Internet store “130”
���������������������������������������������������������
The VIBE CriticalLink range of cabling has been developed to achieve the critical link between source (headunit), amplifier and speakers –
VIBE audio equipment is high quality, using anything less than the VIBE CriticalLink™ range of cables will severely compromise your
equipment and will not allow it to perform to its maximum potential.
NOTE: Your audio equipment will only ever be as good as the cables you use to connect it. The link between your audio equipment is critical
for a bigger cleaner sound.
��������������������������������������������������������������������������������������
�������������������������������.
All Accessories are available direct, for next day delivery call 0870 765 8423
For more product info see www.vibeaudio.co.uk
BASS SYSTEM KIT
The VIBE 3000watt BASS KIT is specifically designed to gain maximum output from high power Bass systems. Featuring the best BASS specific
cables from the VIBE CriticalLink™ Range.
Contents of this Kit:
FLATLINES™ 4AWG PWR Power and Ground cable
FLATBASS™ RCA SolidCore™ Interconnect
FLATBASS™ 13 SPK Bass speaker cable
FLATLINES ™ remote 18
VIBE 140 amp circuit breaker
All cable is terminated with crimped terminal rings in place and accessory fitting kit
COMPATIBILITY
This kit is compatible with the majority of amplifiers on the market – VIBE recommends this kit for all VIBE BASS monoblock amplifiers new, current
and old models.
Model: Bass Kit – Bass specific amplifier wiring kit
STEREO SYSTEM KIT
The VIBE 1500 watt STEREO KIT is specifically designed to gain maximum output from high power full range systems. Combining the best full
range cables from the VIBE CriticalLink ™ range.
Contents of this Kit:
FLATLINES™ 8AWG PWR Power and Ground cable
VIBE FLATSTEREO™ RCA - OFC high definition full range interconnect
FLATLINES ™ remote 18
FLATSTEREO™ speaker cable
AGU Fuse Holder
All cable is terminated with crimped terminal rings in place and accessory fitting kit
COMPATIBILITY
This kit is compatible with the majority of amplifiers on the market – VIBE recommends this kit for all VIBE full range STEREO amplifiers new,
current and old models. FLATLINES™ 8 PWR Power
Model: Stereo Kit – full range stereo amplifier wiring kit
ACTIVE SYSTEM KIT
a
u
.
m
o
The VIBE 1500watt ACTIVE BASS KIT is specifically designed to gain maximum output from high power Active Bass systems (Bass Boxes).
Featuring BASS specific components from the VIBE CriticalLink™ range.
Contents of this Kit:
FLATLINES™ 8AWG PWR Power and Ground cable
FLATBASS™ RCA SolidCore™ Interconnect
FLATLINES ™ remote 18
AGU Fuse Holder
FastPlug™
COMPATIBILITY
This kit is compatible with the majority of amplifiers on the market – VIBE recommends this kit for all VIBE active bass enclosures new, current and
old models.
Model: Active Kit – Bass specific active enclosure wiring kit
c
.
0
3
1
The VIBE 1.5 farad power capacitor is a must for any high performance audio system. VIBE’s 1.5 farad power capacitor
bridges the gap between the vehicles battery and the amplifiers ensuring rapid smooth current flow resulting in louder
tighter bass and clean crisp midrange and treble. The built in digital voltage display constantly and accurately displays the
systems DC voltage. An all new VIBE power distribution block is built into the top of the capacitor to allow easy wiring into
the system and also will allow 3 amplifiers to be wired directly to the capacitor for maximum current flow to the amplifiers.
Model: PC15
The Deltabox line driver is the ideal solution for those looking to install multiple amplifiers from a single RCA preout. Most people use
RCA “Y” splitters for this task unaware of the signal degradation caused. The Deltabox not only divides the signal but also isolates and
boosts the signal up to a maximum of 9 volts independently for each of the 3 output channels giving much cleaner sound and
excellent signal to noise ratio. For SPL competition the Deltabox is an essential tool as each of the outputs can be split 4 times giving
control of 12 amplifiers from a single gain enabling precise adjustment of the system without having to reset every amplifier
individually. Additionally if your headunit has a weak preout or you wish to run multiple amps but only have one output the Deltabox™
is your ideal solution. Model: DELTABOX
The VIBE FastPlug™ (pat. pending), is a product long overdue. Designed and developed by VIBE Engineers the plug
offers safe, fast removal of your active bass enclosure (bass box) or amplifier. You may wish to remove your
system for security reasons, or for the full use of your boot space, whatever the reason the VIBE FastPlug makes
it easy and safe.
The plug is a heavy duty connector that connects positive, negative and remote wires. It is made up of 2 parts –
one end to connect to your equipment and the other to your power source – made from high quality ABS plastic
the device is tough and hard wearing. Model: FASTPLUG
FLATLINES™ Power and Ground Cable
VIBE FlatLines™ power cable has been developed to maximises voltage transfer from battery to amplifier - The cable has 2 main lines
running side by side which are made up of fine copper strands - This design makes the cable flat allowing us to make very slim heavy duty
power cable which is highly flexible easing installation.
Available in: system kits, by the roll or by the metre
Model: FLATLINES 8 PWR – 8gauge red power cable Model: FLATLINES 8 GND – 8gauge black power cable
Model: FLATLINES 4 PWR – 4gauge red power cable Model: FLATLINES 4 PWR – 4gauge red power cable
Model: FLATLINES 0 PWR – 0gauge red power cable Model: FLATLINES 0 GND – 0gauge black power cable
FLATSTEREO™ High Definition full range Interconnect
The VIBE FLATSTEREO RCA is an OFC high definition full range interconnect – delivering the fullest signal possible from source to
amplifier - the cable make up has been developed to run flat with left and right cables running parallel both with individual screening but
sharing an outer FLAT jacket easing installations.
Available in:
Model: FlatStereo RCA 1m – 1 metre full range interconnect
Model: FlatStereo RCA 5m - 5 metre full range interconnect
FLATBASS™ – SolidCore™ Bass interconnect
The VIBE FLATBASS™ interconnect has been specifically developed for use in BASS SYSTEMS - the cable make up has a unique super
FLAT™ design easing installation - Its trick ingredient is oversized SolidCore™ OFC signal wires - allowing a heavier voltage to be passed
down the cable. This is the central wire that caries the main signal from source to amplifier.
Available in:
Model: FlatBass RCA 1m – 1 metre BASS interconnect
Model: FlatBass RCA 5m - 5 metre BASS interconnect
FLATFLEX™ High Definition speaker cable
The delivery of power and signal to the speaker is the final CriticalLink™ in any audio system – VIBES FlatFlex OFC high definition
speaker cable is produced from super fine OFC copper strands collectively picking up all the detail in your music – the multi strands
are aligned in a row making the cable super FLAT™ which can be run invisibly under carpets.
Available in:
Model: FlatFlex 16 SPK – 16 gauge High definition flat flexible speaker cable
Model: FlatFlex 12 SPK – 12 gauge High definition flat flexible speaker cable
Autogood products Internet store “130”