Bosch DCN Wireless Discussion System
Data Brochure
Table of Contents
Introduction
Examples
Example 1
Example 2
Example 3
Example 4
1
4
- Discussion
- Electronic Voting
- Interpretation
- Camera Control
Wireless Discussion Units
5
6
7
8
9
DCN-WD-D Wireless Discussion
DCN-WDD-D Wireless Dual Discussion
DCN-WDV-D Wireless
Discussion Voting
DCN-MICS/L Pluggable Microphone Short/Long Stem
DCN-DISR Rims for Discussion Units
DCN-DISBCM Buttons Chairman (10 sets)
DCN-DISBDD Buttons Dual Use (10 sets)
DCN-WPS Power Supply for Wireless Discussion
9
11
13
13
15
16
16
17
17
Central Control Equipment
18
DCN-WAP Wireless Access Point
DCN-WCCU Wireless Central Control Unit
19
20
Battery Packs
22
DCN-WLIION-D Battery Pack for Wireless Discussion
DCN-WCH05 Charger for 5 Battery Packs
23
24
Accessories
25
DCN-WFCD10 Flight Case for 10 Wireless Discussion
DCN-WFCCCU Flight Case for CCU and WAP
LBC 1259/00 Universal Floorstand
25
25
26
Software
28
DCN-SWSMV Synoptic Microphone and Voting Software
29
Other Applicable Congress Products
30
LBB 3441/10 Under the Chin Headphones
LBB 3442/00 Single Earphone
LBB 3443 Lightweight Headphones
HDP-ILN Induction Loop Neckband
LBB 3015/04 High Quality Dynamic Headphones
LBB 9095/30 Interpreter Headphones
DCN-IDESK Interpreter Desk
DCN-MICS/L Pluggable Microphone Short/Long Stem
PRS-4DEX4 Audio Expander Digital
LBB 4402/00 Audio Expander
LBB 4404/00 CobraNet Interface
DCN-DDI Dual Delegate Interface
LBB 3555/00 DCN Intercom Handset
DCN-FHH Hand Held Microphone
LBB 9600/20 Condenser Handheld Microphone
LBC 1215/01 Microphone Clamp
LBC 1221/01 Floor Stand
LBC 1226/01 Adjustable Boom
DCN-FCS Flush Channel Selector
DCN-FEC Flush End Cap (50 pcs)
LBB 4116 Series DCN Extension Cables
LBB 4117/00 DCN Cable Locking Clamp (25 pcs)
LBB 4118/00 DCN Termination Plug
LBB 4119/00 DCN Connectors (25 pairs)
DCN-DDB Data Distribution Board
LBB 4410/00 Optical Network Splitter
LBB 4414/10 Fiber Interface Without Address
LBB 4416 Series Optical Network Cables
31
31
32
33
33
34
35
37
38
39
41
42
43
44
45
47
47
48
49
50
50
51
51
52
53
54
55
56
www.boschsecurity.com
LBB 4417/00 Set Network Connectors (20 pcs)
56
LBB 4418/00 Cable Connector Tool Kit
57
LBB 4419/00 Cable Couplers (10 pcs)
57
LTC 8200 Allegiant Video Switcher
58
LTC 8555/00 Allegiant Keyboard
59
LTC 5136 Autodome Controller
60
G3A Series AutoDome System
61
LTC 0455 Series Color Camera
62
MON152CL 15-inch Color LCD Flat Panel Display Monitor 63
Bosch Security Systems B.V.
Bosch Security Systems B.V.
www.boschsecurity.com
Introduction | 1
Introduction
Introduction
Introduction
Wireless Discussion System
Innovation
Bosch brings innovation to the congress world, with its new
state-of-the-art and user-friendly Wireless Discussion
System. Suitable for both small and large venues, the Bosch
DCN Wireless Discussion System offers organizations
unparalleled functionality and flexibility. Featuring an awardwinning Wireless Access Point (WAP) that is easy to
position, as well as separate battery packs for simple
charging and changing, the DCN Wireless Discussion System
is designed with the user in mind, whether that user is a
system administrator, chairman or participant.
Range of equipment
The Bosch DCN Wireless Discussion product line includes:
• Wireless Discussion Units
• Wireless Access Point (WAP)
• a central control unit
• congress control software
• information displays and installation equipment
• simultaneous interpretation and optional language
distribution equipment
Maximum flexibility
Conferences and seminars can be set up with a great degree
of freedom due to the Bosch DCN Wireless System’s flexible
design. The WAP can be mounted on a wall, ceiling or
tripod, and is easily positioned for best technical or
aesthetic effect. Individual wireless discussion units can be
added or rearranged by simply picking them up and moving
them. With minimal time required for set-up or break-down,
multiple events can be planned in sequence with virtually no
delays. The DCN Wireless System gives great support to
conferences and seminars anywhere people meet.
www.boschsecurity.com
The system can be further complemented by external
equipment such as PCs, monitors, power amplifiers,
loudspeakers and printers, all of which are easily integrated
into the DCN Wireless Discussion System.
Bosch Security Systems B.V.
2 | Introduction
Easy maintenance
Simple battery maintenance is essential for a wireless
system. The Bosch DCN Wireless System ensures that
battery power is available when needed. Discussion units
use lithium-ion batteries with little or no charge degradation
during their long life. A fully charged battery lasts
approximately 20 hours, which is far longer than most
meetings or conferences. Batteries have a short recharge
time – as little as a few hours – and only the battery packs
need to be removed; the discussion units can remain in
place. Furthermore, each unit has a patent-pending “sleep
mode” to conserve power consumption during longer
breaks,. And, with the remote overview available via the
Congress Control Software, an administrator can view the
power consumption status of all active discussion units.
Secure and stable communication
All signals within the DCN Wireless System are digitally
protected against tapping or eavesdropping. The intelligent
system even features automatic subscription blocking.
Further subscriptions are prevented, even if the
administrator forgets to close the subscription process.
Wireless Discussion System
Contribution equipment
Contribution equipment refers to the units that participants
use to take part in a conference. Depending on the type of
contribution unit used, participants can listen, speak, and
take part in electronic voting. The wireless discussion units
are designed for all kinds of gatherings and meetings and
offer a high level of functionality, digital convenience, and
distinctive styling. The basic discussion unit has a
microphone with an on/off button and status indicators;
more advanced units have dual discussion possibilities (for
two participants) and voting functionality. All discussion
units can be configured as a chairman unit.
Superb Sound and Speech Quality
The sound quality of the DCN Wireless System is first rate –
up to 20 kHz. Each robust unit produces crystal-clear sound
due to a very high signal-to-noise ratio. Units are also
protected against interference from other mobile equipment
using WiFi, Bluetooth or microwave signals. Being a mobile
phone-proof system, participants can leave their mobile
phones switched on during meetings without disrupting the
discussion system signal.
Bosch Security Systems B.V.
The WAP is linked to the WCCU using Bosch's proprietary
optical network, which provides digital optical
communication and power supply over a single cable. The
second optical network connector on the WAP allows the
system network to be expanded from a single branch to a
redundant loop configuration. In this ‘loop-through’
configuration, DCN Wireless can be interfaced with
compatible Bosch equipment such as Audio Expanders,
CobraNet™ interfaces and the Integrus language distribution
system.
Secure wireless communication between the WAP and the
discussion units is in the 2.4 GHz band, which is license-free
worldwide.
Central control equipment
The Bosch Wireless Central Control Unit (CCU) is the heart
of the congress management system. The CCU can operate
stand-alone to provide automatic conference control, or be
administered by an operator via a PC if more extensive
management is required. All CCUs can control up to 150
discussion units (such as delegate and chairman units) and
up to 93 Interpreter desks.
Fully automatic conference proceedings
In basic mode, the CCU automatically manages conference
proceedings and does not require operator control. It
provides basic microphone management, simultaneous
interpretation with up to 32 high-quality audio channels
including floor and voting facilities. This effectively allows
unsupervised control of even large, international
conferences.
www.boschsecurity.com
Introduction | 3
Operator control via a PC
Although the CCU offers basic functionality automatically,
there is extended functionality with operator control via a
PC. Specially developed Bosch Congress Control Software
is easy to install and gives precise control over the Bosch
DCN Wireless Discussion System. Highly user-friendly, the
discussion unit icons of the synoptic control interface are
easily assigned to various operating functions. Operators
can view on/off status of each unit, the identity of its user,
and many other key properties. The software has a
Windows™ look and feel and allows on-the-spot coverage
testing of whether all the units are correctly receiving the
signal. If voting units are used, results can be shown on a
large display screen and logged if desired. The software is
optimized for touch screens, and features a multi-lingual
graphical user interface (GUI). If the PC fails, the CCU will
revert to a default operation enabling conference
proceedings to continue.
Advanced audio coupling
It is possible to extract and insert both digital (AES/EBU or
SPDIF) and analog audio. Other advanced audio coupling
techniques include CobraNet™, a system which allows
distribution of many real-time, high-quality digital audio
channels over an Ethernet network using CAT5 cables. Made
up of software, hardware and a network protocol,
CobraNet™ makes it easy to distribute audio in buildings
and connect the Bosch DCN Wireless Discussion System to
other audio CobraNet™ compatible devices such as Audio
Recorders and Audio Mixers.
Simultaneous interpretation and language distribution
equipment
The DCN Wireless Discussion System supports simultaneous
interpretation via Bosch Interpreter desks. Integrus, a digital
and wireless infrared language distribution system, is
connected to the optical network and enables sound to be
distributed reliably across 32 channels via the Integrus
infrared digital transmitter. Equipped with individual
Integrus receivers, participants can receive their language
channel while moving around freely, without any loss of
contact or quality.
Interpreter Desk for multi-lingual sessions
The Bosch DCN Next Generation Interpreter Desk
accommodates up to 32 high-quality audio channels, all with
an audio-bandwidth of 20 kHz. Up to six desks can be
installed per interpreter booth. Each desk can be used
stand-alone or as part of a system. When used stand-alone,
the desk’s built-in microprocessor is manually programmed
to allocate language channels, channel routing and
interlocks.
www.boschsecurity.com
Delegate with Wireless Discussion Unit
Integrus IR digital technology
Integrus incorporates IR digital technology that conforms to
IEC 60603 part 7. IR digital technology ensures maximum
sound quality with a signal-to-noise ratio of 80 dB. Integrus
also incorporates a special operation mode to couple rooms.
This means that multiple systems, located in separate
rooms, can provide exactly the same language. For more
information about Integrus, see the Integrus Data Brochure.
Information screens
Information screens are ideal for quick and effective
information distribution to many conference participants. A
display shows the image of the current speaker, who has the
floor, and who has a request to speak. Displays also show
results when voting is used.
Automatic camera control
The system can automatically show an image of the current
speaker on monitors or projection screens in the main hall,
lobby, interpreters’ booths, breakout rooms or anywhere
else required. Delegate information appears along with the
image. For a general overview of all delegates the system
can switch to fixed-angle cameras.
Camera control and configuration is automatic, so the
system can be run without an operator. Bosch Auto- Dome
cameras are ideal for this application and especially useful
when video conferencing between sites.
Camera control ensures that participants always have
appropriate details on the current speaker.
Bosch Security Systems B.V.
4 | Examples
Examples
Bosch Security Systems B.V.
www.boschsecurity.com
Examples | 5
Example 1 - Discussion
Introduction
The wireless system can be adjusted to meet any discussion
requirement: from a basic set-up requiring no operator to a
fully interactive voting arrangement.
Shopping List
1.
Bosch Wireless Central Control Unit
2.
Personal computer with Bosch DCN Control Software
3.
Bosch Battery Pack Charger
4.
Bosch Wireless Access Point
5.
Bosch Dual Wireless Discussion Unit
www.boschsecurity.com
Bosch Security Systems B.V.
6 | Examples
Example 2 - Electronic Voting
Introduction
For interactive situations where polling and voting are
important, discussion units with voting functionality can be
used in the DCN Wireless Discussion System.
Shopping List
1.
Bosch Wireless Discussion Unit with Voting
(delegate/chairman mode)
2.
Bosch Wireless Central Control Unit
3.
Personal computer with Bosch DCN Control Software
4.
Large Screen
5.
Bosch Wireless Access Point
6.
Bosch Battery Pack Charger
Bosch Security Systems B.V.
www.boschsecurity.com
Examples | 7
Example 3 - Interpretation
Introduction
Interpreters are located in soundproof booths and are
equipped with Bosch interpreter units. In combination with
the DCN Wireless Discussion System, the Integrus System
allows sound to be digitally distributed and received in CD
HiFi audio quality.
Shopping List
1.
Bosch Wireless Discussion Unit
2.
Bosch Wireless Access Point
3.
Bosch Battery Pack Charger
4.
Bosch Autodome Camera
5.
Interpreter Desk
6.
Bosch Integrus digital infrared language distribution system
7.
Infrared radiator
www.boschsecurity.com
Bosch Security Systems B.V.
8 | Examples
Example 4 - Camera Control
Introduction
The system can automatically show an image of the current
speaker on monitors or projection screens. Delegate
information appears along with the image. For a general
overview of all delegates the system can switch to fixedangle cameras. Camera control and configuration is
automatic, so the system can be run without an operator.
Shopping List
1.
Bosch Wireless Discussion Unit
2.
Bosch Wireless Central Control Unit
3.
Bosch Wireless Access Point
4.
Bosch Autodome Camera
5.
Personal computer with Bosch DCN Control Software
6.
Bosch Battery Pack Charger
Bosch Security Systems B.V.
www.boschsecurity.com
Wireless Discussion Units | 9
DCN-WD-D Wireless Discussion
Wireless Discussion Units
The unit also accommodates two headphone connections,
so the speaker can be heard clearly even with excessive
background noise. To prevent acoustic feedback the built-in
loudspeaker is muted when the microphone is on. If
enabled, the headphones volume is also automatically
reduced to prevent acoustic feedback when the microphone
is on.
Rims are available in a range of colors to match the interior
(DCN-DISR, to be ordered separately).
The unit can be used as a delegate unit or as a chairman
unit (DCN-DISBCM chairman buttons to be ordered
separately).
Simple battery maintenance is essential in a wireless
system. A unique feature of Bosch's wireless discussion
units are the separate rechargeable battery packs (DCNWLIION, to be ordered separately). These Lithium-ion
battery packs can be removed and replaced in a matter of
seconds, providing maximum flexibility in recharge
scheduling.
Features
X
Used as delegate or chairman unit
X
Separate battery pack, easy to change and charge
X
Advanced power saving techniques
X
Low susceptibility to electromagnetic interference
X
Auto microphone-off
X
Auto-search for own network
X
Auto switch-off when out of range
Functions
Controls and Indicators
On front
• Microphone button with a red or green illuminated ring.
Red indicates microphone is active, green indicates
request-to-speak accepted
• Headphone volume control buttons
On rear
Introduction
• Out-of-range indicator
To the participant the most important part of a conference
system is the discussion unit. Bosch has built on the elegant
design of the DCN Next Generation discussion units to
create a new series of wireless discussion units with
unrivalled looks and features.
• Battery low indicator
Maximum speech intelligibility is guaranteed at all times.
Operating in the 2.4 GHz (license free) band the wireless
discussion units produce crystal-clear sound due to a very
high signal-to-noise ratio. The system is also protected
against interference from other wireless equipment such as
mobile phones, Bluetooth devices and WiFi networks.
Interconnections
Wireless communication means extra security
considerations. The DCN Wireless system and discussion
units therefore feature multiple-layer protection to prevent
eavesdropping and unauthorized access. Digital protection
ensures the information within the system remains
confidential.
The DCN-WD-D Wireless Discussion Unit enables
participants to speak, register a request-to-speak, and listen
to the speaker.
A socket is provided to connect the pluggable microphones
which are available in short and long stem versions (DCNMICS and DCN-MICL, to be ordered separately).
www.boschsecurity.com
Under base
• Recessed ‘De-init’ switch
• Mode select switches (delegate, chairman, etc.)
• Socket for pluggable microphone
• Two 3.5 mm (0.14 in) headphone sockets stereo jack
type
• DC power input from DCN-WPS (accessible when battery
pack is removed)
Technical Specifications
Electrical
Frequency response
Headphone load impedance
Output power
Mechanical
Mounting
Dimensions (H x W x D)
without microphone
Weight
without battery
with battery
30 Hz - 20 kHz
> 32 ohm< 1k ohm
2 x 15 mW/32 ohm
Tabletop
61 x 190 x 160 mm (2.4 x 7.5 x 6.3 in)
485 g (1.07 lb)
700 g (1.54 lb)
Bosch Security Systems B.V.
10 | Wireless Discussion Units
Mechanical
Color top
Color base
Silver (RAL 9022)
Charcoal (PH 10736)
Ordering Information
DCN-WD-D Wireless Discussion
pluggable microphone, dark base, wireless
DCN-MICS Pluggable Short Microphone
length 310 mm (12.2 inch)
DCN-MICL Pluggable Long Microphone
length 480 mm (18.9 inch)
DCN-DISRH-SR Rim High Gloss Silver (10 pcs)
silver, high gloss, set of 10
DCN-DISR-SR Rim Silver (10 pcs)
silver, set of 10
DCN-DISR-D Rim Dark (10 pcs)
dark, set of 10
DCN-DISRMH Rim Metal High Gloss (10 pcs)
metal, high gloss, set of 10
DCN-DISRMS Rim Metal Semi Gloss (10 pcs)
metal, semi gloss, set of 10
DCN-DISBCM Buttons Chairman (10 sets)
set of 10
DCN-WLIION-D Battery Pack for Wireless
Discussion
charcoal color, lithium-ion, 7.2 VDC, 4800 mAh
DCN-WPS Power Supply for Wireless
Discussion
powers wireless discussion units if no battery
pack is present
DCN-WFCD10 Flight Case for 10 Wireless
Discussion
light grey, holds 10 wireless discussion units and
2 charging units
Bosch Security Systems B.V.
DCN-WD-D
DCN-MICS
DCN-MICL
DCN-DISRH-SR
DCN-DISR-SR
DCN-DISR-D
DCN-DISRMH
DCN-DISRMS
DCN-DISBCM
DCN-WLIION-D
DCN-WPS
DCN-WFCD10
www.boschsecurity.com
Wireless Discussion Units | 11
DCN-WDD-D Wireless Dual
Discussion
The unit also accommodates two separate headphone
connections with individual volume control on either side of
the unit, allowing one unit to serve two delegates. It can be
converted to a full dual-use unit by replacing the
microphone button with two separate buttons for individual
microphone control and individual delegate identification
(DCN-DISBDD dual-use buttons, to be ordered separately).
To prevent acoustic feedback the built-in loudspeaker is
muted when the microphone is on. If enabled, the
headphones volume is also automatically reduced to prevent
acoustic feedback when the microphone is on.
Different rims are available to allow matching with the
interior (DCN-DISR, to be ordered separately).
The unit can be used as:
• a single delegate unit
• a dual delegate unit
• a chairman unit (DCN-DISBCM chairman buttons, to be
ordered separately)
• a single delegate unit with auxiliary button (to be used as
an usher call, for example).
Features
X
Two separate headphone connections with individual
volume control
Simple battery maintenance is essential in a wireless
system. A unique feature of Bosch's wireless discussion
units are the separate rechargeable battery packs (DCNWLIION, to be ordered separately). These Lithium-ion
battery packs can be removed and replaced in a matter of
seconds, providing maximum flexibility in recharge
scheduling.
X
Useable as single/dual delegate or chairman unit
X
Separate battery pack, easy to change and charge
X
Advanced power saving techniques
X
Low susceptibility to electromagnetic interference
X
Auto microphone-off
Functions
X
Auto-search for own network
Auto switch-off when out of range
Controls and Indicators
X
Introduction
To the participant the most important part of a conference
system is the discussion unit. Bosch has built on the elegant
design of the DCN Next Generation discussion units to
create a new series of wireless discussion units with
unrivalled looks and features.
Maximum speech intelligibility is guaranteed at all times.
Operating in the 2.4 GHz (license free) band, the wireless
discussion units produce crystal-clear sound due to a very
high signal-to-noise ratio. The system is also protected
against interference from other wireless equipment such as
mobile phones, Bluetooth devices and WiFi networks.
Wireless communication means extra security
considerations. The DCN Wireless system and discussion
units therefore feature multiple-layer protection to prevent
eavesdropping and unauthorized access. Digital protection
ensures the information within the system remains
confidential.
The DCN-WDD-D Wireless Dual Discussion Unit enables
participants to speak, register a request-to-speak, and listen
to the speaker.
On front
• Microphone button with a red or green illuminated ring
(red indicates microphone is active, green indicates
request-to-speak accepted)*
• Two individual headphone volume control buttons
On rear
• Out-of-range indicator
• Battery low indicator
Under base
• Recessed ‘De-init’ switch
• Mode select switches (delegate, chairman, etc.)
Interconnections
• Socket for pluggable microphone
• Two 3.5 mm (0.14 in) headphone sockets stereo jack
type
• DC power input from DCN-WPS (accessible when battery
is removed)
* When unit is used in Dual Delegate mode, this function is
available individually.
A socket is provided to connect the pluggable microphones
which are available in short and long stem versions (DCNMICS and DCN-MICL, to be ordered separately).
www.boschsecurity.com
Bosch Security Systems B.V.
12 | Wireless Discussion Units
Technical Specifications
Electrical
Frequency response
Headphone load impedance
Output power
Mechanical
Mounting
Dimensions (H x W x D)
without microphone
Weight
without battery
with battery
Color top
Color base
30 Hz - 20 kHz
> 32 ohm< 1k ohm
2 x 15 mW/32 ohm
Tabletop
61 x 190 x 160 mm (2.4 x 7.5 x 6.3 in)
500 g (1.10 lb)
715 g (1.57 lb)
Silver (RAL 9022)
Charcoal (PH 10736)
Ordering Information
DCN-WDD-D Wireless Dual Discussion
dual delegate, pluggable microphone, dark base,
wireless
DCN-DISBDD Buttons Dual Use (10 sets)
set of 10
DCN-MICS Pluggable Short Microphone
length 310 mm (12.2 inch)
DCN-MICL Pluggable Long Microphone
length 480 mm (18.9 inch)
DCN-DISRH-SR Rim High Gloss Silver (10 pcs)
silver, high gloss, set of 10
DCN-DISR-SR Rim Silver (10 pcs)
silver, set of 10
DCN-DISR-D Rim Dark (10 pcs)
dark, set of 10
DCN-DISRMH Rim Metal High Gloss (10 pcs)
metal, high gloss, set of 10
DCN-DISRMS Rim Metal Semi Gloss (10 pcs)
metal, semi gloss, set of 10
DCN-DISBCM Buttons Chairman (10 sets)
set of 10
DCN-WLIION-D Battery Pack for Wireless
Discussion
charcoal color, lithium-ion, 7.2 VDC, 4800 mAh
DCN-WPS Power Supply for Wireless
Discussion
powers wireless discussion units if no battery
pack is present
DCN-WFCD10 Flight Case for 10 Wireless
Discussion
light grey, holds 10 wireless discussion units and
2 charging units
Bosch Security Systems B.V.
DCN-WDD-D
DCN-DISBDD
DCN-MICS
DCN-MICL
DCN-DISRH-SR
DCN-DISR-SR
DCN-DISR-D
DCN-DISRMH
DCN-DISRMS
DCN-DISBCM
DCN-WLIION-D
DCN-WPS
DCN-WFCD10
www.boschsecurity.com
Wireless Discussion Units | 13
DCN-WDV-D Wireless
Discussion Voting
The unit has five voting buttons. The yellow indicator rings
around the voting buttons confirm vote selections.
The unit also accommodates two headphone connections,
so the speaker can be heard clearly even in situations with
excessive background noise.
To prevent acoustic feedback the built-in loudspeaker is
muted when the microphone is on. If enabled, the
headphones volume is also automatically reduced to prevent
acoustic feedback when the microphone is on.
A socket is provided to connect the pluggable microphones
which are available in short and long stem versions (DCNMICS and DCN-MICL, to be ordered separately).
The unit can be used as:
• a delegate unit
• a chairman unit (DCN-DISBCM chairman buttons to be
ordered separately)
• a delegate unit with auxiliary button (can be used as an
usher call for example)
Features
X
Five voting buttons
X
Usable as delegate or chairman unit
X
Separate battery pack, easy to change and charge
X
Advanced power saving techniques
X
Low susceptibility to electromagnetic interference
X
Auto microphone-off
X
Auto-search for own network
X
Auto switch-off when out of range
Introduction
To the participant the most important part of a conference
system is the discussion unit. Bosch has built on the elegant
design of the DCN Next Generation discussion units to
create a new series of wireless discussion units with
unrivalled looks and features.
Maximum speech intelligibility is guaranteed at all times.
Operating in the 2.4 GHz (license free) band the wireless
discussion units produce crystal-clear sound due to a very
high signal-to-noise ratio. The system is also protected
against interference from other wireless equipment such as
mobile phones, Bluetooth devices and WiFi networks.
Wireless communication means extra security
considerations. The DCN Wireless system and discussion
units therefore feature multiple-layer protection to prevent
eavesdropping and unauthorized access. Digital protection
ensures the information within the system remains
confidential.
Simple battery maintenance is essential in a wireless
system. A unique feature of Bosch's wireless discussion
units are the separate rechargeable battery packs (DCNWLIION, to be ordered separately). These Lithium-ion
battery packs can be removed and replaced in a matter of
seconds, providing maximum flexibility in recharge
scheduling.
Functions
Controls and Indicators
On front
• Five voting buttons with indicator rings around the
buttons
• Unit activity / delegate presence indicator
• Microphone button with a red or green illuminated ring.
Red indicates microphone is active, green indicates
request-to-speak accepted
• Headphone volume control buttons
On rear
• Out-of-range indicator
• Battery low indicator
Under base
• Recessed ‘De-init’ switch
• Mode select switches (delegate, chairman, etc.)
Interconnections
• Socket for pluggable microphone
• Two 3.5 mm (0.14 in) headphone sockets stereo jack
type
• DC power input from DCN-WPS (accessible when battery
The DCN-WDV-D Wireless Discussion Unit with Voting
enables participants to speak, register a request-to-speak,
listen to the speaker, and vote.
A socket is provided to connect the pluggable microphones
(DCN-MICS and DCN-MICL, to be ordered separately).
www.boschsecurity.com
is removed)
Technical Specifications
Electrical
Frequency response
30 Hz - 20 kHz
Bosch Security Systems B.V.
14 | Wireless Discussion Units
Electrical
Headphone load impedance
Output power
Mechanical
Mounting
Dimensions (H x W x D)
without microphone
Weight
without battery
with battery
Color top
Color base
> 32 ohm< 1k ohm
2 x 15 mW/32 ohm
Tabletop
61 x 190 x 160 mm (2.4 x 7.5 x 6.3 in)
505 g (1.11 lb)
720 g (1.58 lb)
Silver (RAL 9022)
Charcoal (PH 10736)
Ordering Information
DCN-WDV-D Wireless Discussion Voting
voting, pluggable microphone, dark base, wireless
DCN-DISBDD Buttons Dual Use (10 sets)
set of 10
DCN-MICS Pluggable Short Microphone
length 310 mm (12.2 inch)
DCN-MICL Pluggable Long Microphone
length 480 mm (18.9 inch)
DCN-DISRH-SR Rim High Gloss Silver (10 pcs)
silver, high gloss, set of 10
DCN-DISR-SR Rim Silver (10 pcs)
silver, set of 10
DCN-DISR-D Rim Dark (10 pcs)
dark, set of 10
DCN-DISRMH Rim Metal High Gloss (10 pcs)
metal, high gloss, set of 10
DCN-DISRMS Rim Metal Semi Gloss (10 pcs)
metal, semi gloss, set of 10
DCN-DISBCM Buttons Chairman (10 sets)
set of 10
DCN-WLIION-D Battery Pack for Wireless
Discussion
charcoal color, lithium-ion, 7.2 VDC, 4800 mAh
DCN-WPS Power Supply for Wireless
Discussion
powers wireless discussion units if no battery
pack is present
DCN-WFCD10 Flight Case for 10 Wireless
Discussion
light grey, holds 10 wireless discussion units and
2 charging units
Bosch Security Systems B.V.
DCN-WDV-D
DCN-DISBDD
DCN-MICS
DCN-MICL
DCN-DISRH-SR
DCN-DISR-SR
DCN-DISR-D
DCN-DISRMH
DCN-DISRMS
DCN-DISBCM
DCN-WLIION-D
DCN-WPS
DCN-WFCD10
www.boschsecurity.com
Wireless Discussion Units | 15
DCN-MICS/L Pluggable
Microphone Short/Long Stem
Ordering Information
DCN-MICL Pluggable Long Microphone
length 480 mm (18.9 inch)
DCN-MICL
Features
X
Uni-directional microphone on adjustable stem
X
Built-in plop and windshield
Introduction
The innovative, stylish and ergonomically designed
microphone with an adjustable stem simply plugs directly
into a Discussion unit, Concentus, flush-mounted
Microphone Connection panes or Interpreter desk. It has a
uni-directional response for optimum performance even in
noisy conditions, and has low susceptibility to interference
from mobile phones.
Functions
Controls and Indicators
• Red or green illuminator. Red indicates microphone is
active, green indicates request-to-speak accepted
Interconnections
• Connector to plug and fasten the microphone
Technical Specifications
Mechanical
Mounting
Length
DCN-MICS
DCN-MICL
Weight
DCN-MICS
DCN-MICL
Color top
Plug and fasten into Discussion units, Concentus, flush mounted Microphone connection panels and Interpreter desks
310 mm (12.2 in)
480 mm (18.9 in)
100 g (0.22 lb)
115 g (0.25 lb)
Silver (RAL 9022)
Ordering Information
DCN-MICS Pluggable Short Microphone
length 310 mm (12.2 inch)
www.boschsecurity.com
DCN-MICS
Bosch Security Systems B.V.
16 | Wireless Discussion Units
DCN-DISR Rims for Discussion
Units
Introduction
A rim completes the discussion units. A variety of rims with
different finishes are available to allow matching with any
interior.
DCN-DISBCM Buttons Chairman
(10 sets)
Introduction
DCN-DISBCM buttons for Chairman Discussion Units replace
the single microphone button on a discussion unit when
used in chairman mode. These buttons can also be used for
the discussion unit in auxiliary control mode.
Technical Specifications
Mechanical
Mounting
Color base
DCN-DISRH-SR
DCN-DISR-SR
DCN-DISR-D
DCN-DISRMH
DCN-DISRMS
Click and fit on any discussion unit
Silver (RAL 9022) high gloss
Silver (RAL 9022)
Charcoal (PH 10736)
High gloss metal
Semi gloss metal
Technical Specifications
Mechanical
Mounting
Color
Click and fit on any Discussion unit
Silver (RAL 9022)
Ordering Information
DCN-DISBCM Buttons Chairman (10 sets)
set of 10
Ordering Information
DCN-DISRH-SR Rim High Gloss Silver (10 pcs)
silver, high gloss, set of 10
DCN-DISR-SR Rim Silver (10 pcs)
silver, set of 10
DCN-DISR-D Rim Dark (10 pcs)
dark, set of 10
DCN-DISRMH Rim Metal High Gloss (10 pcs)
metal, high gloss, set of 10
DCN-DISRMS Rim Metal Semi Gloss (10 pcs)
metal, semi gloss, set of 10
Bosch Security Systems B.V.
DCN-DISBCM
DCN-DISRH-SR
DCN-DISR-SR
DCN-DISR-D
DCN-DISRMH
DCN-DISRMS
www.boschsecurity.com
Wireless Discussion Units | 17
DCN-DISBDD Buttons Dual Use
(10 sets)
DCN-WPS Power Supply for
Wireless Discussion
Features
X
Powers wireless discussion units if no battery pack is
present
Introduction
The DCN-WPS power supply enables wireless discussion
units to be used without a battery.
The DCN-WPS does not provide any battery charging
capability (a DCN-WCH05 charging unit is required). The
unit comes complete with a 1.5 m cable and international
mains supply connectors (Euro, UK, Rest of World).
Introduction
DCN-DISBDD buttons for Dual Use Discussion Units replace
the single microphone button on a discussion unit when
used in dual delegate mode.
Technical Specifications
Mechanical
Mounting
Color
Click and fit on any Discussion unit
Silver (RAL 9022)
Ordering Information
DCN-DISBDD Buttons Dual Use (10 sets)
set of 10
www.boschsecurity.com
DCN-DISBDD
Technical Specifications
Electrical
Rated input voltage
Rated output voltage
100-240 VAC (50 – 60 Hz), 150 mA
9 VDC (500 mA)
Mechanical
Dimensions (H x W x D)
Weight (per package)
Color
65 x 57 x 28 mm (25.6 x 22.4 x 11 in)
approx. 100 g (0.22 lb)
Black
Ordering Information
DCN-WPS Power Supply for Wireless Discussion
powers wireless discussion units if no battery
pack is present
DCN-WPS
Bosch Security Systems B.V.
18 | Central Control Equipment
Central Control Equipment
Bosch Security Systems B.V.
www.boschsecurity.com
Central Control Equipment | 19
DCN-WAP Wireless Access Point
Installation/Configuration Notes
DCN-WAP mounted on a LBC 1259/00 floor stand
Features
X
Compact and elegant (iF design award winner 2006)
X
Single cable for power and communication
X
Mountable on ceiling, wall, or floor stand for best
Technical Specifications
Electrical
Power consumption
4W
reception
X
Secure, digitally protected, wireless communication
X
Typical range 30 m (100 ft)
Introduction
The DCN Wireless Access Point (WAP) links the central
control unit (WCCU) and the wireless discussion units. To
ensure security, data exchange between the WAPs and the
wireless discussion units is digitally protected.
The WAP is linked to the WCCU using Bosch's proprietary
optical network, which provides digital optical
communication and power supply over a single cable. The
second optical network connector on the WAP allows the
system network to be expanded from a single branch to a
redundant loop configuration. In this ‘loop-through’
configuration, DCN Wireless can be interfaced with
compatible Bosch equipment such as Audio Expanders,
CobraNet™ interfaces and the Integrus language distribution
system.
Secure wireless communication between the WAP and the
discussion units is in the 2.4 GHz band, which is license-free
worldwide.
The WAP unit’s award winning design enables it to be
placed unobtrusively on a wall, ceiling, or floor stand by
using the universal mounting bracket.
Mechanical
Mounting
Dimensions (H x W x D)
with bracket
Weight
with bracket
without bracket
Color
Ceiling, Wall or Floor Stand (using included bracket)
59 x 284.5 x 201 mm (2.3 x 11.2 x 7.9 in)
907 g (2 lb)
643 g (1.4 lb)
Light grey (RAL 000 7500)
Ordering Information
DCN-WAP Wireless Access Point
light grey color, universal mounting bracket included
DCN-WFCCCU Flight Case for CCU and WAP
light grey, holds wireless central control unit(s),
access point & cable
LBC 1259/00 Universal Floorstand
lightweight aluminum construction, foldable,
M10 x 12 reducer flange
DCN-WAP
DCN-WFCCCU
LBC1259/00
Functions
Controls and Indicators
• LEDs show status of wireless system
Interconnections
• Two optical network connections (second connection can
be used in ‘loop-through’ network)
www.boschsecurity.com
Bosch Security Systems B.V.
20 | Central Control Equipment
DCN-WCCU Wireless Central
Control Unit
• Voting control for parliamentary voting procedure when
using PC and DCN-SWSMV software
• Simultaneous interpretation function with up to 31
language channels, plus one floor channel via Integrus
language distribution system
• Basic intercom function
• Automatic camera control
• Extended conference facilities when using PC and DCNSWSMV software
• Adjustable sensitivity for audio inputs and outputs
• Audio insertion facility to connect external audio
processing devices or telephone couplers
• Configuration of WCCU and system via a display and a
single rotary push button
• Each WCCU can be assigned a unique name by the
installer for easy identification
Features
• VU meter readings of audio inputs and outputs
(monitored using a headphone)
X
Optical network interface for easy connection
X
Single branch or redundant loop networks
X
Control for up to 150 wireless discussion units
• Handgrips for easy transport
X
Additional control for up to 93 interpreter desks
Controls and Indicators
X
Serial ports for PC and camera control
At the front
• 19” (2U) housing for table top or rack mounting
Introduction
• Mains on/off switch
The DCN-WCCU is the brain of the DCN Wireless system. It
provides control for up to 150 wireless discussion units and
93 interpreter units.
• 2 x 16 Character LCD display for status information and
The WCCU uses Bosch's proprietary optical network for easy
connection to the wireless access point and other Bosch
congress equipment. Networks can be set-up in single
branch or redundant loop configurations, depending on the
installed equipment.
At the rear
For connection to DCN-IDESK interpreter desks, the WCCU
has two outlet sockets for DCN trunk-cables.
In combination with a PC and the Conference Control
Software (DCN-SWSMV), the WCCU brings greater
sophistication to conference control.
CCU configuration
• Rotary control to navigate through the LCD menus
• Four red LED overload indicators (2 for the DCN network
outputs, 2 for the optical connections)
Interconnections
• Euro mains socket with built-in fuse
• Two DCN outlet sockets to connect DCN-IDESK
interpreter desks, plus extension power supplies. Each
socket is protected against short-circuit (2 x six-pole
circular sockets)
• Two optical network connectors for a Wireless Access
Point, Audio Expanders or Integrus TX
• Two three-pole XLR balanced audio line inputs with
Functions
• Optical network to:
–
–
couple the WCCU to the WAP
allow a variety of audio contribution and distribution
facilities (can connect to other Bosch congress
equipment, such as: Integrus transmitter for infra-red
language distribution; Audio Expanders, and
CobraNet™ interfaces)
• DCN trunk to connect to DCN-IDESK interpreter desks
optional galvanic separation.
• Two stereo Cinch unbalanced audio line inputs
• Two three-pole XLR balanced audio line output with
galvanic separation.
• Two stereo Cinch unbalanced audio line outputs
• One headphone output 3.5 mm (0.14”) stereo
• Two RS-232 serial data connectors for controlling PC and
diagnostics
• Basic microphone management facilities
• Three operational microphone modes:
–
Open: microphone button control with request-tospeak (Auto)
– Override: microphone button with override of
activated microphones (FIFO)
– PTT: Push To Talk (push and hold button to speak)
• Up to 4 open microphones (3 for delegates and 1 for the
chairman)
Bosch Security Systems B.V.
www.boschsecurity.com
Central Control Equipment | 21
Parts Included
Ordering Information
Quantity
Component
1
DCN-WCCU Wireless Central Control Unit
1
System installation and user instruction CD-ROM
1
Mains cable, 1.7 m (5.5 ft)
plus:
19” rack mounting brackets, detachable feet and
mounting accessories
Technical Specifications
Electrical
Supply voltage
Power consumption
DCN system supply
Optical network supply
Total supply power
RS-232 connection
100 - 240 VAC +/- 10 %
50 – 60 Hz
170 W
40 VDC, max 65 W per DCN socket
40 VDC, max 65 W
130 W
2 x nine-pole Sub-D female socket
Frequency response
THD at nominal level
Cross talk attenuation
Dynamic range
Signal-to-noise ratio
30 Hz - 20 kHz (-3 dB at nominal level)
< 0.5 %
> 85 dB at 1 kHz
> 90 dB
> 87 dBA
Audio inputs
XLR nominal input
XLR maximum input
Cinch nominal input
Cinch maximum input
12 dBV (+/- 6 dB)
+12 dBV
24 dBV (+/- 6 dB)
+0 dBV
Audio outputs
XLR nominal output
XLR maximum output
Cinch nominal output
Cinch maximum output
12 dBV (+6 / -24 dB)
+12 dBV
24 dBV (+6 / -24 dB)
+0 dBV
Mechanical
Mounting
Dimensions (H x W x D)
for tabletop use, with feet
for 19” rack use, with brackets
in front of brackets
behind brackets
Weight
Color
DCN-WFCCCU Flight Case for CCU and WAP
light grey, holds wireless central control unit(s),
access point & cable
DCN-WCCU-UL Wireless Central Control Unit UL/
CSA
for the North-America region
DCN-WFCCCU
DCN-WCCU-UL
Accessories
LTC 8200/50 Allegiant Video Switcher
rated voltage 220 to 240 VAC (50/60 Hz)
LTC 8200/60 Allegiant Video Switcher
rated voltage 120 VAC (50/60 Hz)
LTC 0455/11 Color Camera
1/3-inch, 540 TVL, PAL, DSP, 12 VDC/24 VAC,
50 Hz
LTC 0455/21 Color Camera
1/3-inch, 540 TVL, NTSC, DSP, 12 VDC/24 VAC,
60 Hz
LTC 0455/51 Color Camera
1/3-inch, 540 TVL, PAL, DSP, 230 VAC, 50 Hz
LTC 0455/61 Color Camera
1/3-inch, 540 TVL, NTSC, DSP, 120 VAC, 60 Hz
LTC 8555/00 Compact Full-function Keyboard
variable speed joystick
G3ACPW2CW Color AutoDome Kit
18x color, indoor pendant, wall mount, clear
dome, white, 230 VAC, 50 Hz
LTC 5136/51 Autodome Controller
with 16 outputs for AutoDomes or for Allegiant
Receiver/Drivers units, 230 VAC, 50/60 Hz
G3ACS5C Color AutoDome Kit
18x color, indoor drop ceiling, clear dome, 24
VAC, 50 Hz
LTC 5136/61 Autodome Controller
with 16 outputs for AutoDomes or for Allegiant
Receiver/Drivers units, 110 VAC, 50/60 Hz
LTC8200/50
LTC8200/60
LTC0455/11
LTC0455/21
LTC0455/51
LTC0455/61
LTC8555/00
G3ACPW2CW
LTC5136/51
G3ACS5C
LTC5136/61
Tabletop or mounted in a 19” rack
92 x 440 x 400 mm
(3.6 x 17.3 x 15.7 in)
88 x 483 x 400 mm
(3.5 x 19 x 15.7 in)
40 mm (1.6 in)
360 mm (14.2 in)
7 kg (15.4 lbs)
Charcoal (PH 10736) with silver
Ordering Information
DCN-WCCU Wireless Central Control Unit
for all regions except North-America
www.boschsecurity.com
DCN-WCCU
Bosch Security Systems B.V.
22 | Battery Packs
Battery Packs
Bosch Security Systems B.V.
www.boschsecurity.com
Battery Packs | 23
DCN-WLIION-D Battery Pack for
Wireless Discussion
Mechanical
Color
Charcoal (PH 10736)
Ordering Information
DCN-WLIION-D Battery Pack for Wireless Discussion
charcoal color, lithium-ion, 7.2 VDC, 4800 mAh
DCN-WCH05 Charger for 5 Battery Packs
DCN-WLIION-D
DCN-WCH05
Features
X
Long service life without charge degradation
X
20 hours typical use from a full charge
X
Fully recharges in 3 hours
X
Built-in microprocessor controls charging cycle
X
Lithium-ion technology
Introduction
This rechargeable battery is the power source of the
wireless discussion units.
The battery is a high capacity Lithium-ion type, capable of
providing up to 20 hours typical use from a full charge. Fully
charging the DCN-WLIION from empty takes just 3 hours.
Lithium-ion cells avoid the charge degradation issues
associated with other rechargeable battery types. This
offers maximum flexibility for scheduling recharges (no
requirement to fully discharge batteries before recharging).
The ‘intelligent’ battery has a built-in microprocessor to
control charging current and prevent overloading.
Functions
Controls and Indicators
• Charge capacity LEDs and push-to-test button
Interconnections
• Power / charge connector
Technical Specifications
Electrical
Output Voltage
Capacity
7.2 VDC
4800 mAh
Mechanical
Dimensions (H x W x D)
Weight
61.5 x 136 x 22 mm (2.4 x 5.5 x 0.9 in)
215 g (0.47 lb)
www.boschsecurity.com
Bosch Security Systems B.V.
24 | Battery Packs
DCN-WCH05 Charger for 5
Battery Packs
Technical Specifications
Electrical
Supply Voltage
Maximum power consumption
100 - 240 VAC +/- 10 %
50 – 60 Hz
190 W
Mechanical
Dimensions (H x W x D)
Weight (without batteries)
Color
340 x 195 x 82 mm (13.4 x 7.6 x 3.2 in)
1.4 kg (3.08 lb)
Charcoal (PH 10736)
Ordering Information
DCN-WCH05 Charger for 5 Battery Packs
DCN-WCH05
Features
X
Simultaneous charging of up to 5 battery packs
X
Recharges from empty in 3 hours
X
Loop-through mains connector
X
Auto-ranging PSU, 100 – 240 VAC
Introduction
This unit can simultaneously re-charge up to 5 DCN-WLIION
battery packs. The charging status of each pack is shown on
individual charge capacity indicator LEDs.
The unit is suitable for tabletop use, or can be wallmounted.
The loop-through mains voltage connector allows a
maximum number of charging units to be connected in
series to share from the same mains outlet:
• A maximum 5 chargers can be connected in series for 100
- 127 VAC, 50 - 60 Hertz regions
• A maximum 10 chargers can be connected in series for
220 - 240 VAC, 50 - 60 Hertz regions
Functions
Controls and Indicators
• Charge capacity indicator LEDs on each bin
• Mains power indicator LED
Interconnections
• Mains supply connector
• Loop-through mains connector
• Battery pack charging connector
Bosch Security Systems B.V.
www.boschsecurity.com
Accessories | 25
DCN-WFCD10 Flight Case for 10
Wireless Discussion
DCN-WFCCCU Flight Case for
CCU and WAP
Features
Features
Accessories
Holds 10 wireless discussion units and microphones
X
Robust construction with reinforced corners
Also holds 2 battery chargers and 10 batteries
X
Easy to carry and store
X
Robust construction with reinforced corners
X
Shaped interior
X
Easy to carry and store
X
Holds WCCU, WAP and network cabling
X
Shaped foam interior simplifies (un)packing
Introduction
X
X
Introduction
The DCN-WFCD10 Flight Case accommodates up to 10
wireless discussion units complete with battery packs and
microphones (long or short stems).
The case also holds 2 DCN-WCH05 charging units.
Technical Specifications
Mechanical
Dimensions (H x W x D)
Weight
Color
The DCN-WFCCU Flight Case provides a secure
transportation and storage solution for:
• a Wireless Central Control Unit, Wireless Access Point
and optical network cable
• 2 x Wireless Central Control Units (if dividing foam
partition is removed from case)
Technical Specifications
500 x 770 x 300 mm (19.7 x 30.3 x 12 in)
9 kg (19.8 lb)
Light grey
Mechanical
Dimensions (H x W x D)
Weight
Color
480 x 510 x 295 mm
(18.9 x 20.1 x 11.46 in)
6 kg (13.2 lb)
Light grey
Ordering Information
DCN-WFCD10 Flight Case for 10 Wireless Discussion
light grey, holds 10 wireless discussion units and
2 charging units
www.boschsecurity.com
DCN-WFCD10
Ordering Information
DCN-WFCCCU Flight Case for CCU and WAP
light grey, holds wireless central control unit(s),
access point & cable
DCN-WFCCCU
Bosch Security Systems B.V.
26 | Accessories
LBC 1259/00 Universal
Floorstand
Accessories
For storage and ease of transport, a carrier bag is available
with two inside compartments with separate zippers for
holding two universal floorstands (LBC 1259/00). The bag,
with Bosch logo, is made from sturdy black weather-proof
nylon. Two handles are fitted for carrying the bag by hand or
over the shoulder.
LM1-CB Carrier Bag (optional)
Installation/Configuration Notes
Features
X
Multi-purpose, lightweight aluminum stand
X
For mounting a loudspeaker, wireless access point or
Integrus radiator
X
Double-braced folding base
X
Reducer flange for different mountings
X
Hand-adjustable
X
Carrier bag for two pieces as optional accessory
Introduction
This universal floorstand provides effective mounting
solutions for loudspeaker installations, a Wireless Access
Point of the DCN-Wireless system, or a radiator of the
Integrus digital language distribution system. They are
manufactured and finished to the same high standards as all
Bosch products, assuring excellent quality and guaranteed
compatibility throughout the range. The LBC 1259/00 is
suited to a wide range of applications where a secure yet
transportable mounting solution is required.
LBC 1259/00 with DCN Wireless Access Point, LBB 451x/00 Infra-red
Radiator and XLA 3200 Line Array Loudspeaker
Parts Included
Quantity
Component
1
LBC 1259/00 Universal Floorstand
1
36 mm (1.42 in) reducer flange with (M10 x 12) threaded pin
1
M10 securing knob for WAP mounting bracket
Functions
Adjustable and safe
The LBC 1259/00 floorstand is hand-adjustable using a
spring-loaded locking screw for heights between 1.4 and
2.2 m (4.6 and 7.2 ft). An extra safety bolt on the support
can be tightened to ensure the stand remains extended.
This lightweight stand has a double-braced folding base for
extra strength, and a wide leg span to ensure stability.
Adaptable
The floorstand is standard supplied with a 36 mm (1.42 in)
reducer flange with an M10 x 12 threaded pin to mount
different sized equipment, and with an M10 knob to fix the
Wireless Access Point mounting bracket.
Bosch Security Systems B.V.
Technical Specifications
Mechanical
Length
standing
folded
Width
legs extended
legs folded
Weight
Max. load
Material
Tube diameter
Thread
1.375 to 2.185 m (54 to 86 in)
1.20 m (47 in)
980 mm (38.6 in)
130 mm (5.1 in)
3.5 kg (7.7 lb)
50 kg (110.2 lb)
Aluminum
36 mm (1.42 in)
1/2" Whitworth
www.boschsecurity.com
Accessories | 27
Mechanical
Carrier bag accessory
Dimensions (L x D)
Weight
Color
Material
1.25 m x 27 mm (49 x 1.06 in)
750 g (1.65 lb)
Black with light grey handles
Nylon
Ordering Information
LBC 1259/00 Universal Floorstand
lightweight aluminum construction, foldable,
M10 x 12 reducer flange
LM1-CB Carrier Bag for two floorstands LBC
1259/00
www.boschsecurity.com
LBC1259/00
LM1-CB
Bosch Security Systems B.V.
28 | Software
Software
Bosch Security Systems B.V.
www.boschsecurity.com
Software | 29
DCN-SWSMV Synoptic
Microphone and Voting Software
• Microphone control mode allows you to observe and
control the state of each individual microphone.
Microphones can be switched on and off, or placed in the
‘request to speak’ queue.
• Battery and signal view mode shows the remaining
battery charge time and the signal strength for each
wireless discussion unit
• Voting result mode shows individual results in different
colors according to votes cast
Note:
The different symbols in the various modes are
specially designed so that they are also easily
identified by persons with the visual disability of
color blindness.
The application provides parliamentary voting functionality.
The system operator can summon delegates to vote, as well
as starting and stopping voting sessions. Final vote results
can be automatically printed or exported to a file; the
software can also be configured to send real-time voting
information to Microsoft PowerPoint® for display.
Features
X
Synoptic room overview for monitoring and controlling
the microphones
X
Voting control with individual results
X
Real-time voting results displayed in Microsoft
PowerPoint®
X
On-screen help in many languages
Introduction
The DCN-SWSMV Synoptic Microphone and Voting Software
provides a range of conference facilities when used in
combination with a DCN Wireless or DCN Next Generation
system. The available functions include automatic seat
assignment, synoptic microphone monitoring and control,
and voting management.
Although it offers many powerful features, the software is
extremely easy to use thanks to its innovative design. The
application moves away from traditional control panels and
buttons and replaces them with a highly intuitive graphic
user interface. All functions are controlled from a single
window making the software suitable for touch screen
operation. The software features on-screen help in most
major languages.
Real-time voting results in Microsoft PowerPoint®
Ordering Information
DCN-SWSMV Synoptic Microphone and Voting
Software
DCN-SWSMV
The user interface is based on a graphical representation of
the conference venue. When a device is connected to the
system it is automatically recognized and an icon is created
for it on the on-screen room layout. The icons display
information about device status and can be used by the
operator to select individual devices for remote control
functions. If a device becomes disconnected from the
system, a red cross is displayed on top of its icon to alert
the operator.
The Synoptic Microphone and Voting Software can operate
in the following modes, depending on the required task:
• Assignment mode allows you to assign names to
microphone icons. The positions of the icons on the room
layout can also be changed using the standard windows
‘drag & drop’.
www.boschsecurity.com
Bosch Security Systems B.V.
30 | Other Applicable Congress Products
Other Applicable Congress Products
Bosch Security Systems B.V.
www.boschsecurity.com
Other Applicable Congress Products | 31
LBB 3441/10 Under the Chin
Headphones
LBB 3442/00 Single Earphone
Features
X
Lightweight single earphone
X
Left or right ear use
Features
X
Lightweight stereo headphones
X
Ergonomic design for use under the chin
Functions
X
Replaceable ear tips
Right-angled, gold-plated jack plug
Interconnections
X
• 1.2 m (4 ft) cable terminated with 3.5 mm (0.14 in) jack
plug
Functions
Interconnections
Technical Specifications
• 1.2 m (4 ft) cable terminated with 3.5 mm (0.14 in) right-
Electrical
Impedance
Audio frequency response
Power handling capacity
Sensitivity (1 kHz)
32 ohm
100 Hz - 5 kHz (-10 dB)
5 mW
114 dB SPL/earpiece at 1 mW/earpiece
Mechanical
Weight
Color
25 g (0.06 lb)
Dark grey
angled stereo jack plug
Technical Specifications
Electrical
Impedance
Audio frequency response
Power handling capacity
Sensitivity (1 kHz)
150 ohm per earpiece
50 Hz – 5 kHz (-10 dB)
60 mW
107 dB SPL/earpiece at 1 mW/earpiece
Mechanical
Weight
Color
33 g (0.07 lb)
Black
Ordering Information
LBB 3442/00 Single Earphone
LBB3442/00
Ordering Information
LBB 3441/10 Under the Chin Headphones
LBB 3441/50 Ear Tips for LBB 3441 (500
pairs)
www.boschsecurity.com
LBB3441/10
LBB3441/50
Bosch Security Systems B.V.
32 | Other Applicable Congress Products
LBB 3443 Lightweight
Headphones
Ordering Information
LBB 3443/00 Lightweight Headphones
LBB 3443/10 Lightweight Headphones Durable
Cable
LBB3443/00
LBB3443/10
Accessories
LBB 3443/50 Foam Ear Pads for LBB 3443
(50 pairs)
replacement foam ear pads
HDP-LWSP Solid Ear Pads for LBB 3443 (50
pairs)
washable replacement ear pads
LBB3443/50
HDP-LWSP
Features
X
Lightweight with high quality sound reproduction
X
Replaceable ear pads
X
Available with normal or durable cable
X
Separate available solid washable ear pads
Functions
These headphones can be fitted with an optional set of
washable ear pads.
Washable ear pads
Interconnections
• 1.3 m (4.25 ft) cable terminated with gold-plated 3.5 mm
(0.14 in) angled stereo jack plug
Technical Specifications
Electrical
Impedance
Audio frequency response
Power handling capacity
Sensitivity (1 kHz)
32 ohm per earpiece
50 Hz - 20 kHz (-10 dB)
50 mW
98 dB SPL/earpiece at 1 mW/earpiece
Mechanical
Weight
Finish
70 g (0.16 lb)
Charcoal (PH 10736) with silver
Bosch Security Systems B.V.
www.boschsecurity.com
Other Applicable Congress Products | 33
HDP-ILN Induction Loop
Neckband
LBB 3015/04 High Quality
Dynamic Headphones
Features
X
Lightweight
X
Used with ‘T-coil’ hearing aids
Features
Functions
This induction loop neckband can be used with:
• Integrus receivers
X
Durable dynamic headphones
X
Replaceable ear pads
X
High-quality sound reproduction
X
Gold-plated stereo jack plug
• CCS800 unit
• DCN unit
The neckband magnetically couples the sound signal from
the headphone output to a ‘T-coil’ hearing aid.
Interconnections
• 0.9 m (3ft) cable terminated with a 3.5 mm (0.14 in)
gold-plated plug
• 1.5 m (5 ft) cable terminated with a 3.5 mm (0.14 in)
stereo jack plug
Electrical
Impedance
Audio frequency response
Power handling capacity
Sensitivity (1 kHz)
45 g (0.10 lb)
Charcoal with silver
Ordering Information
HDP-ILN Induction Loop Neckband
Interconnections
Technical Specifications
Technical Specifications
Mechanical
Weight
Color
Functions
HDP-ILN
Mechanical
Weight
Color
720 ohm per earpiece
250 Hz - 13 kHz (-10 dB)
200 mW
97 dB SPL/earpiece at 0 dBV/system
96 dB SPL/earpiece at 1 mW/earpiece
110 g (0.24 lb)
Dark grey
Ordering Information
LBB 3015/04 High Quality Dynamic Headphones
LBB 9095/50 Ear pads for LBB 3015 LBB
9095 (25 pairs)
www.boschsecurity.com
LBB3015/04
LBB9095/50
Bosch Security Systems B.V.
34 | Other Applicable Congress Products
LBB 9095/30 Interpreter
Headphones
Features
X
Durable and dynamic
X
Replaceable ear pads
X
High-quality sound reproduction
Introduction
Lightweight, dynamic headphones for direct connection to
DCN-IDESK Interpreters Desk.
Functions
Interconnections
• 2.2 m (7 ft) cable terminated with a 6.3 mm (0.25 in)
stereo jack plug
Technical Specifications
Electrical
Impedance
Audio frequency response
Power handling capacity
Sensitivity (1 kHz)
Mechanical
Weight
Color
720 ohm per earpiece
250 Hz - 13 kHz (-10 dB)
200 mW
97 dB SPL/earpiece at 0 dBV/system
96 dB SPL/earpiece at 1 mW/earpiece
125 g (0.28 lb)
Black/grey
Ordering Information
LBB 9095/30 Interpreter Headphones
LBB 9095/50 Ear pads for LBB 3015 LBB
9095 (25 pairs)
Bosch Security Systems B.V.
LBB9095/30
LBB9095/50
www.boschsecurity.com
Other Applicable Congress Products | 35
DCN-IDESK Interpreter Desk
• Easy programming via menus on the display after entering
the programming mode
• Microphone key with surrounding red “on-air” indicator
and green for “booth not in use”
• Mute key
• Help key
• Slow (speak slowly) key
• Operator and chairman intercom call keys
• Message key with yellow LED indicator
• Telephone and Intercom call yellow LED indicators
• A and B channel engaged yellow LED indicators
• Rotary step control for channel settings (and other
Features
X
Low susceptibility to mobile phone interference
X
Ergonomic design with features for visually impaired
X
Up to 31 interpretation channels and the original floor
X
X
• LCD with backlighting showing selected and activated
output channel with channel numbers and abbreviated
language names
language with an audio bandwidth of 20 kHz
• Loudspeaker rotary volume control
A graphic LCD with backlighting for bright information
• Headphone rotary volume control
display in dark conditions
• Headphone rotary bass and treble tone controls
5 pre-select keys for relay languages with activation
• Beep on/off key
indication at the display
X
functions).
Pressing this button sets the selection to the first
available channel
Compliant to ISO 2603
Introduction
The DCN-IDESK is a single-user interpreter desk with a
stylish and modern design. It fully conforms to
internationally agreed standards. Clear positioning per
functional area of the desk controls allows intuitive
operation without mistakes.
A socket is provided to connect the pluggable microphones
(DCN-MICS and DCN-MICL, to be ordered separately).
• Five Relay language pre-select keys
• Floor/auto-relay key with green LED indicators
• Rotary step control (same as for speaking section) to
select the relay languages for the relay pre-select keys
and the loudspeaker channel. Pressing this button sets
the selection to the first available channel
• LCD with backlighting, showing selected relay language
with channel numbers, abbreviated names and quality
indicators. Also the selected loudspeaker channel with
abbreviated name is shown
Interconnections
• Socket for pluggable microphone
Functions
• A maximum of six desks can be installed per booth
• Tabletop and flush mountable
• Pluggable microphone (DCN-MICS)
• Ergonomic design
Controls and Indicators
• A and B output channel with status and selection
indication at the display
• All channels have channel number, language names and
• Headphone or headset connector (five-pole 180° Din type
socket wired according to IEC 574-3)
• 6.3 mm (0.25 in) and 3.5 mm (0.14 in) stereo jack
headphone connectors
• 2 m (78.7 in) DCN cable with molded six-pole circular
connector
• Six-pole circular socket for loop-through connection to
the DCN network
• Eight-pole modular jack connector for connection to
booth telephone, intercom and booth on-air sign
quality level indicated at the display
• Features for visually impaired such as a small bump on
the middle button, and beeps to indicate microphone on/
off and double relay selected
• Built-in loudspeaker with language channel selector
• Speech timer to indicate elapsed time of interpretation
• Speak slowly facility to alert the current speaker to slow
down
Technical Specifications
Electrical
Headphone connection
Frequency response
Load impedance
Output power
30 Hz - 20 kHz
> 32 ohm
2 x 30 mW/32 ohm
Headset connection
Frequency response
Load impedance
30 Hz - 20 kHz
> 32 ohm
• Help request to an operator or usher
• Booth telephone and intercom indicator
• Automatic headset selection when headset connected
www.boschsecurity.com
Bosch Security Systems B.V.
36 | Other Applicable Congress Products
Electrical
Output power
Nominal microphone input
level
Overload microphone input
level
Mechanical
Mounting
Dimensions (H x W x D)
(with microphone)
Slope
Weight
Color top
Color base
DCN-IDESK-L
DCN-IDESK-D
60 mW/32 ohm
7 mVrms
> 124 mVrms
Free-standing or mounted on a table
82 x 330 x 170 mm (3.2 x 13 x 6.7 in)
25 degrees
1.3 kg (2.87 lb)
Silver (RAL 9022)
Light grey (RAL 000 7500)
Charcoal (PH 10736)
Ordering Information
DCN-IDESK-L Interpreter Desk Light
with light base
DCN-IDESK-D Interpreter Desk Dark
with dark base
Bosch Security Systems B.V.
DCN-IDESK-L
DCN-IDESK-D
www.boschsecurity.com
Other Applicable Congress Products | 37
DCN-MICS/L Pluggable
Microphone Short/Long Stem
Ordering Information
DCN-MICL Pluggable Long Microphone
length 480 mm (18.9 inch)
DCN-MICL
Features
X
Uni-directional microphone on adjustable stem
X
Built-in plop and windshield
Introduction
The innovative, stylish and ergonomically designed
microphone with an adjustable stem simply plugs directly
into a Discussion unit, Concentus, flush-mounted
Microphone Connection panes or Interpreter desk. It has a
uni-directional response for optimum performance even in
noisy conditions, and has low susceptibility to interference
from mobile phones.
Functions
Controls and Indicators
• Red or green illuminator. Red indicates microphone is
active, green indicates request-to-speak accepted
Interconnections
• Connector to plug and fasten the microphone
Technical Specifications
Mechanical
Mounting
Length
DCN-MICS
DCN-MICL
Weight
DCN-MICS
DCN-MICL
Color top
Plug and fasten into Discussion units, Concentus, flush mounted Microphone connection panels and Interpreter desks
310 mm (12.2 in)
480 mm (18.9 in)
100 g (0.22 lb)
115 g (0.25 lb)
Silver (RAL 9022)
Ordering Information
DCN-MICS Pluggable Short Microphone
length 310 mm (12.2 inch)
www.boschsecurity.com
DCN-MICS
Bosch Security Systems B.V.
38 | Other Applicable Congress Products
PRS-4DEX4 Audio Expander
Digital
• Two 3-pole XLR AES/EBU stereo inputs for 2 audio
channels per input
• Two Cinch SPDIF stereo inputs for 2 audio channels per
input
• Two 3-pole XLR AES/EBU stereo outputs for 2 audio
channels per output
• Two Cinch SPDIF stereo outputs for 2 audio channels per
output
• Eight control inputs to enable audio inputs and audio
outputs
• Five control outputs to indicate channel engaged state
Parts Included
Features
Quant.
Component
X
Stylish and modern design (IF award)
1
PRS-4DEX4 Digital Audio Expander
X
Room coupling facility
1
Set of mounting brackets for 19” rack
X
Versatile audio distribution facility
1
Set of feet
X
AES/EBU or SPDIF
Sample-rate converters (8 – 96 kHz)
1
Set of connectors
X
X
Optical network coupling
X
Redundant network capability
Introduction
The digital audio expander can contribute audio to and
distribute audio from the system. Typical applications are
room coupling and audio distribution.
Functions
• Automatic Gain Control
• Audio input channels for floor and interpretation
channels
• Audio output channels for floor and interpretation
channels (16-bit 44.1 kHz)
• Flexible routing of floor and interpretation channels
Technical Specifications
Electrical
Supply voltage
Power consumption
24 to 48 VDC
6W
Frequency response
THD at nominal level
30 Hz - 20 kHz
< 0.5 %
Mechanical
Mounting
Dimensions (H x W x D)
for tabletop use, with feet
for 19” rack use, with brackets
• Configuration of the Digital Audio Expander via a display
and a single rotary push button
• Each Digital Audio Expander can be assigned a unique
name by the installer for easy identification
• VU meter readings to monitor audio inputs and audio
in front of brackets
behind brackets
Weight
Color
Tabletop or mounted in a 19” rack
92 x 440 x 400 mm
(3.6 x 17.3 x 15.7 in)
88 x 483 x 400 mm
(3.5 x 19 x 15.7 in)
40 mm (1.6 in)
360 mm (14.2 in)
6 kg (13.2 lbs)
Charcoal (PH 10736) with silver
outputs. The audio can be monitored using headphones
• 19” (2U) housing for tabletop or rack mounting
• Handgrips for easy transportation
• Unit is powered from the network
Controls and Indicators
Ordering Information
PRS-4DEX4 Audio Expander Digital
PRS-4DEX4
• 2 x 16 Character LCD display for status display and
configuration of the Audio Expander
• Rotary control to navigate through the LCD menus
Interconnections
Front
• One stereo headphone output 3.5 mm (0.14 in)
Back
• Two optical network connections for connecting to CCU
Bosch Security Systems B.V.
www.boschsecurity.com
Other Applicable Congress Products | 39
LBB 4402/00 Audio Expander
• Four three-pole XLR balanced audio line inputs with
galvanic separation
• Four stereo Cinch unbalanced audio line inputs
• Four three-pole XLR balanced audio line outputs with
galvanic separation
• Four stereo Cinch unbalanced audio line outputs
• Eight control inputs to enable audio inputs and audio
outputs
• Five control outputs to indicate channel engaged state
Parts Included
Features
Quantity
Component
X
Stylish and modern design (IF award)
1
LBB 4402/00 Audio Expander
X
Room coupling facility
1
Set of mounting brackets for 19” rack
X
Versatile audio distribution facility
1
Set of feet
X
Optical network for coupling to the CCU
1
Set of connectors
X
Redundant network capability
Introduction
The audio expander can contribute audio to and distribute
audio from the system. Typical applications are room
coupling and audio distribution.
Functions
• Redundant network cabling can be either single branch
or redundant loop
• Audio line inputs (of which 2 can be configured as
microphone input) for floor and interpretation channels
• Audio line outputs for floor and interpretation channels
• Flexible routing of floor and interpretation channels
• Adjustable sensitivity for the audio inputs
• Adjustable level for the audio outputs
• Configuration of the Audio Expander via a display and a
single rotary/push button
• Each Audio Expander can be assigned a unique name by
the installer for easy identification
• VU meter readings to monitor audio inputs and audio
outputs. The audio can be monitored using a headphone
• 19” (2U) housing for table top or rack mounting
• Handgrips for easy transportation
• The unit is powered from the network
Controls and Indicators
• 2 x 16 Character LCD display for status display and
configuration of the Audio Expander
• Rotary/push control to navigate through the LCD menus
Interconnections
Front
• One stereo headphone output 3.5 mm (0.14 in)
Back
• Two optical network connections for connecting to the
CCU
www.boschsecurity.com
Technical Specifications
Electrical
Supply voltage
Power consumption
Frequency response
THD at nominal level
Crosstalk attenuation
Dynamic range
Signal-to-noise ratioo
Audio line inputs
XLR nominal input
XLR maximum input
Cinch nominal input
Cinch maximum input
Audio mic inputs
Nominal input
Maximum input
Phantom supply
Audio line outputs
XLR nominal output
XLR maximum output
Cinch nominal output
Cinch maximum output
24 to 48 VDC
7.6 W (DC)
30 Hz to 20 kHz (-3 dB at nominal level)
<0.5%
>85 dB at 1 kHz
>90 dB
>87 dBA
0 dBV (±6 dB)
+12 dBV
+12 dBV (±6 dB)
0 dBV
57 dBV (±6 dB)
26 dBV
12 V ±1 V at 15 mA
12 dBV (+6 / -24 dB)
+12 dBV
24 dBV (+6 / -24 dB)
0 dBV
Mechanical
Dimensions (H x W x D)
for tabletop use, with feet
92 x 440 x 400 mm
(3.6 x 17.3 x 15.7 in)
for 19” rack use, with brackets 88 x 483 x 400 mm
in front of brackets
(3.5 x 19 x 15.7 in)
behind brackets
40 mm (1.6 in)
360 mm (14.2 in)
Weight
7 kg (15.4 lbs)
Mounting
Tabletop, 19”-rack
Color
Charcoal (PH 10736) with silver
Bosch Security Systems B.V.
40 | Other Applicable Congress Products
Ordering Information
LBB 4402/00 Audio Expander
Bosch Security Systems B.V.
LBB4402/00
www.boschsecurity.com
Other Applicable Congress Products | 41
LBB 4404/00 CobraNet Interface
• Two optical network connections
• Two RJ45 Ethernet connectors for the CobraNet™
• Eight control inputs to enable audio inputs and audio
outputs for floor and interpretation channels
• Five control outputs to indicate channel engaged state
Parts Included
Features
X
Stylish and modern design (IF award)
X
Room coupling facility
X
Versatile audio distribution facility
X
CobraNet™ compatible using Ethernet
X
Optical network for coupling to the CCU
X
Redundant network cabling
Introduction
The CobraNet™ Interface can interface audio from the DCN
system to a CobraNet™ network using standard Ethernet
networks. Typical applications are room coupling and audio
distribution over long distances.
CobraNetTM is a registered trademark of Peak Audio, a
Division of Cirrus Logic, Inc.
Functions
Quantity
Component
1
LBB 4404/00 CobraNet Interface
1
Set of mounting brackets for 19” rack
1
Set of feet
1
Set of connectors
Technical Specifications
Electrical
Supply voltage
Power consumption
Frequency response
THD at nominal level
24 to 48 VDC
10.5 W (DC)
30 Hz to 20 kHz
<0.5%
CobraNetTM
Physical layer
Channels
Ethernet
4 in / 4 out per interface
Compliance
Audio Transport
Sample Rate
Latency
Max 64 on CobraNetTM
IEEE 802.3
16 / 20 / 24-bit
48 kHz
5.33 ms
• Redundant network cabling can be either single branch
or redundant loop
• Flexible routing of floor and interpretation channels
• Configuration of the CobraNet™ Interface audio channel
routing via a display and a single rotary push button
• Automatic Gain Control
• Configuration of the CobraNet™ Interface with software
tools included
• Each CobraNet™ Interface can be assigned a unique name
by the installer for easy identification
• VU meter readings to monitor audio inputs and audio
outputs. The audio can be monitored using a headphone
• 19” (2U) housing for table top or rack mounting
• Handgrips for easy transportation
Mechanical
Dimensions (H x W x D)
for tabletop use, with feet
92 x 440 x 400 mm
(3.6 x 17.3 x 15.7 in)
for 19” rack use, with brackets88 x 483 x 400 mm
(3.5 x 19 x 15.7 in)
in front of brackets
40 mm (1.6 in)
behind brackets
360 mm (14.2 in)
Weight
Mounting
Color
7 kg (15.4 lbs)
Tabletop, 19”-rack
Charcoal (PH 10736) with silver
• The unit is powered from the network
Controls and indicators
• 2 x 16-character LCD display for status display and audio
channel routing of the CobraNet™ Interface
Ordering Information
LBB 4404/00 CobraNet Interface
LBB4404/00
• Rotary control to navigate through the LCD menus
Interconnections
Front
• One stereo headphone output 3.5 mm (0.14 in)
Back
www.boschsecurity.com
Bosch Security Systems B.V.
42 | Other Applicable Congress Products
DCN-DDI Dual Delegate Interface
Controls and Indicators
• Three Switches per input with the following possibilities:
–
–
Microphone or line selection
Asymmetrical microphone input, symmetrical
microphone/ line input, or symmetrical microphone
input with phantom power selection
– Input attenuation selection of 0, 6, 12 or 18 dB +/3 dB input level fine adjustment potentiometer per
input Interconnection
• Remote control inputs (switches) and outputs (LEDs)
matching the DCN microphones and control panels
• Switch to select the different modes of the DCN-DDI:
Features
X
Dual Delegate mode for two microphones and two voting
and card panels
X
Two microphone/line inputs
X
Outputs to headphones or loudspeakers
X
Range of mounting options
X
Use for entrance/exit registration
X
Shared microphone with dual microphone control
Introduction
The Dual Delegate Interface is intended for use in flush
mounted custom solutions. It enables a number of functions
to be added, making it suitable for chairmen and delegates.
Such functions include facilities for connecting a Voting
Panel, with or without a Card reader (DCN-FVCRD or DCNFV). In addition, two separate audio inputs are provided that
can also be used as line inputs. Each input can be assigned
its own seat number, allowing the DCN-DDI to serve two
delegate positions.
Settings are available to assign the Dual Delegate Interface
for use as a delegate unit, a dual delegate, chairman unit,
entrance/exit unit or ambient microphone. The ambient
microphone is located in the conference venue, and
automatically switched on when no other delegate unit or
chairman unit microphones are active. In this way,
interpreters always have audio contact with conference
venue.
–
–
–
–
–
–
–
Note:
Dual delegate
Chairman
Dual delegate, one microphone
Dual delegate, muted loudspeakers
Single delegate
Entrance/Exit
Ambient microphone
To use the entrance/exit mode, PC control
software is also required.
Interconnections
• Two RJ11 connectors for Microphone Control Panel DCNFMIC, Priority Panel DCN-FPRIOB, Voting Panel DCN-FV
and Voting and Card Panel DCN-FVCRD
• RJ11 connector for Intercom Handset LBB 3555/00
• Two balanced audio inputs for line (0 dB), or microphone
(-60 dB) sources, with or without a phantom power
supply (2 x eight-pole 262° DIN-type socket)
• Six-pole circular connector for loop-through system
cabling
• 2 m (78.7 in) cable terminated with a molded six-pole
circular connector
• Two 3.5 mm (0.14 in) stereo jack sockets for connection
to headphones or to loudspeaker panel (DCN-FLSP).
Technical Specifications
Mechanical
Mounting
Dimensions (H x W x D)
(excl. cables)
Weight
Color
On wall, under tabletop or seat, in arm rest
or in cable duct
35 x 100 x 170 mm (1.4 x 3.9 x 6.7 in)
500 g (1.10 lb)
Charcoal (PH 10736)
Functions
• The loudspeaker output is switched off when the
corresponding input is switched on
• The unit can be mounted free-standing on a tabletop,
mounted on a wall, or discreetly mounted into tabletops
or into the arm rests of chairs, etc.
Ordering Information
DCN-DDI Dual Delegate Interface
for flush mounted custom solutions
DCN-DDI
• The unit is suitable for Hand-Held Microphones (DCNFHH) or Pluggable Microphones (DCN-MIC) with
Microphone Connection Panel (DCN-FMIC) and
Microphone Control Panel (DCN-FMICB)
• The unit provides a single connection for an Intercom
Handset (LBB 3555/00).
Bosch Security Systems B.V.
www.boschsecurity.com
Other Applicable Congress Products | 43
LBB 3555/00 DCN Intercom
Handset
Features
X
Ideal for intercom applications
X
For use with all Concentus and Dual Delegate Interface
X
Can be permanently mounted to wall, chair or tabletop
Introduction
Lightweight and compact, this robust and attractively styled
handset and cradle enables private 2-way conversation
between conference participants. The handset is hard-wired
to the cradle by a coiled cable, 0.5 m (19.6 in) long when
coiled, and 2 m (78.7 in) uncoiled. The cable is terminated
with a six-pole RJ45 connector for connection to Concentus
and Dual Delegate Interface. When used in permanent
installations, the unit is easily mounted to a tabletop or wall
using the two screws.
Functions
Interconnections
• Six-pole RJ45 socket
Technical Specifications
Mechanical
Mounting
Dimensions (H x W)
Weight
Color
Tabletop or wall-mounted using the 2
screw holes on the cradle
53 x 210 mm (2.08 x 8.26 in)
250 g (0.55 lb)
Charcoal (PH 10736)
Ordering Information
LBB 3555/00 DCN Intercom Handset
with coiled handset cable with 2 m reach, sixpole RJ45 connector
www.boschsecurity.com
LBB3555/00
Bosch Security Systems B.V.
44 | Other Applicable Congress Products
DCN-FHH Hand Held Microphone
Ordering Information
DCN-FHH Hand Held Microphone
cable length 5 m (16.4 ft)
DCN-FHHC Hand Held Microphone
with coiled cable, length un-coiled 1.4 m (4.6 ft)
DCN-FHH
DCN-FHHC
Features
X
Light, portable microphone
X
Built-in plop and windshield
X
On/off switch and LED status indicators
Introduction
The DCN-FHH is a uni-directional, condenser microphone
with built-in plop and windshield. It comfortably fits into
one hand and is ideal for applications where the speaker is
on the move. Two of these microphones can be connected
to the Dual Delegate Interface DCN-DDI.
Functions
Controls and Indicators
• Condenser microphone with built-in plop and windshield
• Microphone on/off or request-to-speak button
• ‘Microphone on’ indicator (red LED)
• ‘Request-to-speak’ confirmation indicator (green LED)
Technical Specifications
Mechanical
Mounting
Dimensions (H x W)
Cable length
DCN-FHH
DCN-FHH-C
Weight
Color
Using clamp LBC 1215/01 the microphone may be mounted on a stand, wall or
on a chair
215 x 30 mm (8.5 x 1.2 in)
5 m (16.4 ft)
Coiled 0.4 m (1.3 ft), un-coiled 1.4 m
(4.6 ft)
350 g (0.77 lb)
Charcoal (PH 10736)
Bosch Security Systems B.V.
www.boschsecurity.com
Other Applicable Congress Products | 45
LBB 9600/20 Condenser
Handheld Microphone
Installation/Configuration Notes
Circuit diagram
Circuit diagram
Features
X
Condenser transducer
X
Unidirectional
X
High speech intelligibility
X
Low sensitivity to case noise and vibrations
X
Phantom powered
X
Rugged construction
X
Modern non-reflecting matt black finish
Introduction
This condenser microphone is based on an electric
transducer element in a sturdy housing with shielding
against wind and wind bursts (pops). It is intended for
public address and sound reinforcement applications, such
as in churches, theaters, and congress centers.
Functions
The handheld LBB 9600/20 is an excellent microphone with
almost frequency independent, unidirectional directivity. Its
low equivalent input noise level and insensitivity to stray
electrostatic and electromagnetic fields keep the audio
signal free from spurious noise.
The microphone has an on/off slide-switch and a 3-pin,
lockable XLR plug. It uses a phantom power supply, which is
available on all microphone inputs on Bosch public address
amplifiers.
It comes with a push-on clip with a Whitworth-threaded
screw fitting, and a multi-thread adaptor (3/8", ½", and 5/
8") for mounting. The supplied 7 m (23 ft) connection cable
has 3-pin, lockable male and female XLR connectors.
Accessories
A number of accessories, such as extension cables, table
stands and floor stands are also available. See the separate
microphone accessories data sheet.
www.boschsecurity.com
Frequency response
Technical Specifications
Electrical*
Phantom power supply
Voltage range
Current consumption
Performance
Polar pattern
Frequency range
Sensitivity
Rated output impedance
Equivalent input noise level
11 V to 52 V (acc. to DIN 45596 and
IEC 268-15A)
<1.5 mA
Unidirectional
100 Hz to 16 kHz
2 mV/Pa +/--3 dB
(-54 dB rel. to 1 V/Pa)
200 ohm
26 dB (A)
* Technical performance data acc. to IEC 60268-4
Mechanical
Dimensions (D x L)
Weight
Color
Switch
54 x 170 mm (2.13 x 6.69 in)
245 g (8.64 oz)
Black
On/off slide
Bosch Security Systems B.V.
46 | Other Applicable Congress Products
Mechanical
Cable type
Cable length
Connector
7 m (23 ft)
3-pin XLR (male)
Environmental
Operating temperature
Storage temperature
Relative humidity
-20 °C to +55 °C (-4 °F to +131 °F)
-40 °C to +70 °C (-40 °F to +158 °F)
<95%
Ordering Information
LBB 9600/20 Condenser Handheld Microphone
7 m (23 ft) cable, 3-pin lockable male and female XLR connectors
LBC 1102/02 Cable Transformer
for galvanic separation
LBC 1221/01 Floor Stand
three folding legs, adjustable length with twist
clamp
LBC 1226/01 Adjustable Boom
maximum reach of 670 mm (2.12 ft); length 840
mm (2.76 ft)
LBC 1227/01 Table Stand
with 3/8" Whitworth stud; 130 mm (5.12 in) diameter
Bosch Security Systems B.V.
LBB9600/20
LBC1102/02
LBC1221/01
LBC1226/01
LBC1227/01
www.boschsecurity.com
Other Applicable Congress Products | 47
LBC 1215/01 Microphone Clamp
Features
X
Quick-release universal microphone clamp
X
Spring-loaded microphone holder
X
Friction angular adjustment
X
Screws onto a 3/8", 1/2" or 5/8" Whitworth thread
X
Holds microphone stem with 19 to 32 mm diameter
LBC 1221/01 Floor Stand
Features
X
Adjustable from 850 to 1600 mm (2.79 to 5.25 ft) with
twist clamp
X
Three folding legs (360 mm; 1.18 ft) for stability
X
Column terminates in male 3/8" Whitworth thread
Introduction
The 1215/01 Microphone Clamp is available for all Bosch
hand-held microphones.
Technical Specifications
Mechanical
Weight
Color
Technical Specifications
Mechanical
Dimensions (folded)
Weight
Color
850 x 110 mm (33.46 x 5.25 in)
2.4 kg (6.43 lb)
matt black
60 g (0.13 lb)
Matt black
Ordering Information
Ordering Information
LBC 1215/01 Microphone Clamp
spring-loaded microphone holder, friction angular adjustment
www.boschsecurity.com
LBC1215/01
LBC 1221/01 Floor Stand
three folding legs, adjustable length with twist
clamp
LBC 1226/01 Adjustable Boom
maximum reach of 670 mm (2.12 ft); length 840
mm (2.76 ft)
LBC1221/01
LBC1226/01
Bosch Security Systems B.V.
48 | Other Applicable Congress Products
LBC 1226/01 Adjustable Boom
Features
X
Adjustable in reach and angle (quick-release screw
clamp)
X
Maximum reach of 670 mm (2.12 ft)
X
Fits onto 3/8" Whitworth thread
Technical Specifications
Mechanical
Length
Weight
Color
840 mm (2.76 ft)
700 g (1.88 lb)
matt black
Ordering Information
LBC 1226/01 Adjustable Boom
maximum reach of 670 mm (2.12 ft); length 840
mm (2.76 ft)
LBC 1221/01 Floor Stand
three folding legs, adjustable length with twist
clamp
Bosch Security Systems B.V.
LBC1226/01
LBC1221/01
www.boschsecurity.com
Other Applicable Congress Products | 49
DCN-FCS Flush Channel Selector
Technical Specifications
Electrical
Frequency response
Headphone Load
impedance
Output power
Mechanical
Mounting
Dimensions (H x W x D)
Weight
Color
30 Hz - 20 kHz
> 32 ohm < 1 k ohm
2 x 15 mW/32 ohm
Flush mounted
40 x 100 x 100 mm (1.6 x 3.9 x 3.9 in)
0.3 kg (0.66 lb)
Silver (RAL 9022)
Ordering Information
Features
X
Stylish and modern design (IF award)
X
Automatically adapts to available channels
X
Built-in “Silent” function
X
No audio output until the headphone is connected
X
Flush mountable in tabletops, on top or at the front, or in
DCN-FCS Flush Channel Selector
flush mounted, silver
DCN-FCS
arm rests of seats
Introduction
The DCN-FCS is a compact and stylish single-user audio
channel selector for listening by headphone. It provides a
choice of up to 32 high-quality audio channels used for
distribution of interpretation and floor channels.
Functions
• Built-in “Silent” function; no audio output until one of the
keys has been pressed to eliminate audible noise from
the headphones when not in use
• Upon insertion of a headphone the default “floor”
channel (channel 0) is selected with a comfortable
headphone volume and the dimmed backlighting is
activated
Controls and Indicators
• Two push-buttons (up/down) for channel selection
• Two push-buttons (up/down) for headphone volume
control
• Backlit 2-digit LCD for channel number indication
Interconnection
Interconnections
• 3.5 mm (0.14 in) stereo jack headphone connector
• Connector for external headphone
• 2 m (78.7 in) cable with a molded six-pole circular
connector
• Six-pole circular connector for loop-through
interconnection
www.boschsecurity.com
Bosch Security Systems B.V.
50 | Other Applicable Congress Products
DCN-FEC Flush End Cap (50 pcs)
LBB 4116 Series DCN Extension
Cables
Features
X
Stylish and modern design (IF award)
Introduction
Matching end caps give a finishing touch to the flush
mounted devices. Two end caps are needed per flush mount
position.
Introduction
Cable terminated at both ends with a molded six-pole
circular connector (male and female). The extension to the
type number gives the length of the cable.
Technical Specifications
Mechanical
Mounting
Dimensions (H x W)
Weight
Color
Click-to-fit in DCN-FCOUP couplings
40 x 20 mm (1.57 x 0.79 in)
2 g (0.004 lb)
Silver (RAL 9022)
Ordering Information
DCN-FEC Flush End Cap (50 pcs)
flush mounted, silver, set of 50
Technical Specifications
Mechanical
Dimensions (dia.)
Material
Color
6 mm (0.24 in)
PVC
Grey
DCN-FEC
Ordering Information
LBB 4116/00 DCN Installation Cable 100m
100 m (328 feet), without connectors
LBB 4116/02 DCN Extension Cable 2m
2 m (6.6 feet), terminated with connectors
LBB 4116/05 DCN Extension Cable 5m
5 m (16.0 feet), terminated with connectors
LBB 4116/10 DCN Extension Cable 10m
10 m (33.0 feet), terminated with connectors
LBB 4116/15 DCN Extension Cable 15m
15 m (49.2 feet), terminated with connectors
LBB 4116/20 DCN Extension Cable 20m
20 m (66.0 feet), terminated with connectors
LBB 4116/25 DCN Extension Cable 25m
25 m (82.0 feet), terminated with connectors
Bosch Security Systems B.V.
LBB4116/00
LBB4116/02
LBB4116/05
LBB4116/10
LBB4116/15
LBB4116/20
LBB4116/25
www.boschsecurity.com
Other Applicable Congress Products | 51
LBB 4117/00 DCN Cable Locking
Clamp (25 pcs)
LBB 4118/00 DCN Termination
Plug
Introduction
Introduction
Matching clamps for male/female cable connectors such as
those on the DCN Extension Cable (LBB 4416). One clamp
per male/ female connector required.
The termination plug is specially designed for use with
opened-ended DCN cabling.
Ordering Information
Ordering Information
LBB 4117/00 DCN Cable Locking Clamp (25 pcs)
set of 25
www.boschsecurity.com
LBB 4118/00 DCN Termination Plug
LBB4118/00
LBB4117/00
Bosch Security Systems B.V.
52 | Other Applicable Congress Products
LBB 4119/00 DCN Connectors
(25 pairs)
Introduction
The set DCN Connectors contains 25 female and 25 male
connectors that can be used with the 100 m (328 ft) DCN
Installation Cable LBB 4116/00.
Ordering Information
LBB 4119/00 DCN Connectors (25 pairs)
Bosch Security Systems B.V.
LBB4119/00
www.boschsecurity.com
Other Applicable Congress Products | 53
DCN-DDB Data Distribution
Board
Technical Specifications
Electrical
External supply
7.5 – 35 VDC.
Mechanical
Dimensions (H x W)
100 x 200 mm (3.93 x 7.87 in)
Ordering Information
DCN-DDB Data Distribution Board
DCN-DDB
Features
X
Drives hall displays
X
Allows transparent data transport for remote control of
external equipment
X
Speak slowly and help indicator control
Introduction
The DCN-DDB is a printed circuit board that is used with
digital equipment such as hall displays, recorder systems
and camera controllers to provide the data communication
link to the DCN Next Generation. Transparent data transport
between data communication boards in the DCN Next
Generation system is possible, i.e. for remote control of
slide projectors, lights, blinds, projection screens etc. It is
intended for mounting in external equipment, and includes
an RS232 communication port with a baud rate of 9600 or
1200 baud - selectable by an onboard dip switch. Optocouplers isolate it from the DCN Next Generation system. It
can be powered by DCN Next Generation system supply or
an external power source. Other function is to control
indicators to show speak slowly and help request from
interpreters. When the interpreter presses the speak slowly
or help button another output control of the DDB is
activated, which can control an indicator of the chairman or
operator’s position.
Functions
Controls and Indicators
• Initialization button with LED indication
Interconnections
• 2 m (78.7 in) cable terminated with a molded six-pole
circular connector
• Multi-pole PCB connector for:
– External initialization button and LED
– 8-bit parallel data input and output
• Nine-pole D-sub socket for RS232 output
www.boschsecurity.com
Bosch Security Systems B.V.
54 | Other Applicable Congress Products
LBB 4410/00 Optical Network
Splitter
Mechanical
Color
Charcoal grey
Ordering Information
LBB 4410/00 Network Splitter
LBB4410/00
Features
X
Redundant network connection
X
Powered externally (48 VDC) or from the CCU
X
External power is not fed into the main cable run
X
Automatically powered from the external power supply
X
Maximum power feed to tap-off outlets can be reduced
X
Repeater function to extend the cable length by 50 meter
(164 ft)
Introduction
The optical network splitter is used in conjunction with the
system installation to tap off two branches from the optical
network cable run.
Functions
Controls and Indicators
• Power on indicator
• Error indicator
• 2 LEDs for diagnostics
• Jumpers to select maximum power fed to the tap offs
Interconnections
• 2 optical network connection for main run
• 2 optical network connection for tap off
• External power supply connector
Technical Specifications
Mechanical
Mounting
Dimensions (H x W x D)
Weight
2 screws in bracket
200 x 82.5 x 28.9 mm
(7.8 x 3.2 x 1.1 in)
0.3 kg (0.66 lb)
Bosch Security Systems B.V.
www.boschsecurity.com
Other Applicable Congress Products | 55
LBB 4414/10 Fiber Interface
Without Address
Ordering Information
LBB 4414/10 Fiber Interface
no network address, multimode
LBB4414/10
Features
X
Redundant network connection
X
Powered externally (48 VDC) or from the CCU
X
Automatically powered from the external power supply
Introduction
The fiber interface is used in conjunction with the system
installation to convert from plastic optical network cable to
glass optical fiber and vice versa.
Functions
Controls and Indicators
• Power on indicator
• Error indicator
• 2 LEDs for diagnostics
• 2 control inputs (for future use)
Interconnections
• 1 optical network connection for plastic optical fiber
• 1 optical network connection for glass optical fiber
• External power supply connector
Technical Specifications
Mechanical
Mounting
Dimensions (H x W x D)
Weight
Color
www.boschsecurity.com
2 screws in bracket
200 x 82.5 x 28.9 mm
(7.8 x 3.2 x 1.1 in)
0.3 kg (0.66 lb)
Charcoal grey
Bosch Security Systems B.V.
56 | Other Applicable Congress Products
LBB 4416 Series Optical
Network Cables
LBB 4417/00 Set Network
Connectors (20 pcs)
Introduction
This is a special cable with 2 plastic fibers for data and
audio communication and 2 copper cores for the power
supply. The cable is supplied with the network connectors
fitted. This cable can be used to connect the CCU to audio
expanders.
The network cables are supplied in different lengths. The
extension (/xx) on the type number indicates the length of
the cable. Only the LBB 4416/00 is without connectors. The
connectors are available separately (LBB 4417/00).
Introduction
The set contains 20 connectors that can be used with the
network cable LBB 4416/00 to make up to ten custom
cables. The cable/connector toolkit LBB 4418/00 is required
for assembly.
Ordering Information
LBB 4417/00 Set Network Connectors (20 pcs)
LBB4417/00
Ordering Information
LBB 4416/00 Network Cable 100 m
without the network connectors fitted
LBB 4416/01 Network Cable Assembly 0.5 m
with the network connectors fitted
LBB 4416/02 Network Cable Assembly 2 m
with the network connectors fitted
LBB 4416/05 Network Cable Assembly 5 m
with the network connectors fitted
LBB 4416/10 Network Cable Assembly 10 m
with the network connectors fitted
LBB 4416/20 Network Cable Assembly 20 m
with the network connectors fitted
LBB 4416/50 Network Cable Assembly 50 m
with the network connectors fitted
Bosch Security Systems B.V.
LBB4416/00
LBB4416/01
LBB4416/02
LBB4416/05
LBB4416/10
LBB4416/20
LBB4416/50
www.boschsecurity.com
Other Applicable Congress Products | 57
LBB 4418/00 Cable Connector
Tool Kit
LBB 4419/00 Cable Couplers
(10 pcs)
Introduction
Cable couplers are used to couple LBB 4416/xx network
cable assemblies for extension.
Parts Included
Quantity
Component
1
Standard cutting pliers
1
Stripping pliers
1
Crimping pliers
Ordering Information
LBB 4419/00 Cable Couplers (10 pcs)
1
Plastic optical fiber cutting/stripping tool
1
Plastic optical fiber positioning and indent tool
1
Torx screw driver
1
Spare cutting system
LBB4419/00
Ordering Information
LBB 4418/00 Cable Connector Tool Kit
LBB 4418/50 Spare cutting system
www.boschsecurity.com
LBB4418/00
LBB4418/50
Bosch Security Systems B.V.
58 | Other Applicable Congress Products
LTC 8200 Allegiant Video
Switcher
Electrical
Rated voltage
Voltage range
120 VAC (50/60 Hz)
100 to 140 VAC
Power consumption
50 W
LTC 8200/50 and LTC 8200/60
Video input signal
0.5 Vpp to 2 Vpp
(composite negative sync.)
Gain
Unity ± 2 % (75 W)
Video bandwidth (-3dB)
25 MHz
Features
X
16 camera inputs and five video outputs
X
Control of AutoDome® Series dome cameras
X
Compact single bay construction
Mechanical
Mounting
Dimensions (H x W x D)
Weight
Rack mounting brackets included
40 x 440 x 305 mm
(1.7 x 17.3 x 12 in)
4 kg (8.8 lbs)
Introduction
The LTC 8200 Allegiant Video Switcher provides automatic
camera switching in conference venues. It is easily
configured using the DCN Next Generation Automatic
Camera Control software, and an Allegiant Keyboard. It
ensures that cameras are automatically switched to cover
the speaking delegate in conferences.
The LTC 8200 has 16 video inputs for connecting cameras.
Either fixed or dome cameras can be connected. There are
also five video outputs used to connect hall displays or
monitors.
Ordering Information
LTC 8200/50 Allegiant Video Switcher
rated voltage 220 to 240 VAC (50/60 Hz)
LTC 8200/60 Allegiant Video Switcher
rated voltage 120 VAC (50/60 Hz)
LTC8200/50
LTC8200/60
Up to four Allegiant Keyboards can be connected.
Functions
Controls and Indicators
• 48-character on-screen display
Interconnections
• 16 x BNC Video inputs
• 5 x monitor outputs
• Console, RS232 port for external PC or control interface
(CCU of DCN system) - 9-pin D-type connector
• Biphase out, multiple ports (12 for LTC 8200) for camera
control - removable screw terminal connection blocks.
• Keyboards, Multiple ports (4 for LTC 8200) for keyboard
connection - 6-pin RS485 ports for Allegiant Keyboard
use.
Technical Specifications
Electrical
LTC 8200/50
Rated voltage
Voltage range
Power consumption
220 to 240 VAC (50/60 Hz)
198 to 264 VAC
50 W
LTC 8200/60
Bosch Security Systems B.V.
www.boschsecurity.com
Other Applicable Congress Products | 59
LTC 8555/00 Allegiant Keyboard
Features
X
Full-function, ergonomically-designed keyboard
X
Variable speed joystick control
X
48-character on-screen display
Introduction
The LTC 8555/00 Allegiant Keyboard is used with the LTC
8200 Allegiant Video Switcher. It provides a convenient
means of operating and configuring the switcher. It is
equipped with a variable-speed pan and tilt joystick control
for positioning cameras, and also has an attractive screen
for displaying camera information.
Functions
The Allegiant Keyboard and Allegiant Video Switcher are
used with the DCN Next Generation Automatic Camera
Control software. A range of Allegiant Keyboard accessories
is available, including a keyboard extension cable, keyboard
extension kit and keyboard rack mount kit.
Controls and Indicators
• Joystick control
• On-screen display
Technical Specifications
Mechanical
Dimensions (H x W x D)
Weight
51 x 220 x 155 mm
(2 x 8.7 x 6.1 in)
0.55 kg (1.2 lbs)
Ordering Information
LTC 8555/00 Compact Full-function Keyboard
variable speed joystick
www.boschsecurity.com
LTC8555/00
Bosch Security Systems B.V.
60 | Other Applicable Congress Products
LTC 5136 Autodome Controller
Mechanical
Weight
0.55 kg (1.2 lbs)
Ordering Information
LTC 5136/51 Autodome Controller
with 16 outputs for AutoDomes or for Allegiant
Receiver/Drivers units, 230 VAC, 50/60 Hz
LTC 5136/61 Autodome Controller
with 16 outputs for AutoDomes or for Allegiant
Receiver/Drivers units, 110 VAC, 50/60 Hz
LTC5136/51
LTC5136/61
Features
X
Full-function, ergonomically-designed keyboard
X
Variable speed joystick control
Introduction
This AutoDome® Controller provides the same functionality
as an Allegiant Keyboard and Allegiant video switcher to
configure and control a Bosch AutoDome® system. It is
required in DCN Next Generation systems with Direct
Camera Control to preposition an AutoDome® system. The
AutoDome® is temporarily connected for this purpose to the
AutoDome® Controller for setting the prepositions as
required for the different DCN Next Generation microphone
units. After positioning the settings, the AutoDome® system
is connected to the DCN Next Generation CCU. The
AutoDome® Controller is also needed to change the
programmed pre-positions when required.
Functions
Controls and Indicators
• Joystick control
• On-screen display
Technical Specifications
Electrical
LTC 5136/51
Rated voltage
Voltage range
Power consumption
220 to 240 VAC (50/60 Hz)
195.5 to 253 VAC
6W
LTC 5136/61
Rated voltage
Voltage range
120 VAC (50/60 Hz)
105 to 132 VAC
Power consumption
6W
Mechanical
Dimensions (H x W x D)
101 x 220 x 155 mm
(4 x 8.7 x 6.1 in)
Bosch Security Systems B.V.
www.boschsecurity.com
Other Applicable Congress Products | 61
G3A Series AutoDome System
Direct Camera control
The DCN Next Generation can also be used in the Direct
Camera Control (DCC) mode. A single AutoDome system is
then directly connected to a CCU for automatic camera
control. The video output of the AutoDome system is
connected to a monitor or other video display device. The
DCC mode is available both for DCN Next Generation standalone systems without a control PC and for DCN Next
Generation systems with control PC. Setting AutoDome
system pre-positions in DCN Next Generation systems with
DCC requires use of AutoDome controller, both for DCN
Next Generation stand-alone systems and PC-controlled
DCN Next Generation systems. The DCC mode can only be
used in combination with:
• a Bosch AutoDome
• Central Control Unit DCN-CCU or DCN-CCUB
Features
X
Integral camera pan/tilt and receiver/driver system
X
360 degrees observation
X
High-speed pan/tilt operation
X
Up to 99 prepositions
Introduction
The G3A Series AutoDome System allows total observation
of a large area with a single camera system. The system,
with its built-in camera, driver and integral highspeed pan
and tilt, provides 360° observation. It is possible to program
the system with up to 99 pre-positions.
Functions
The Bosch G3A Series AutoDome System is ideal for
conference venues. Its powerful auto-focus zoom lens allows
it to produce clear, close-up shots of speaking delegates, in
all sizes of congress venue. The high-speed pantilt operation
means it can quickly switch positions, and the 360° angle of
operation means all seating positions can be covered. It is
comprised of a camera/lens module, a backbox/ power
supply module and a dome module. The dome system is a
compact, lightweight system containing a high-performance
1/4-inch color CCD camera with an 18:1 auto-iris, auto-focus
zoom lens. Additional zoom power is provided by a 12 x
digital electronic zoom. Integral high-speed pan/tilt and
variable speed operation allow accurate, high-speed camera
positioning. The camera, lens and pan/tilt module can easily
be removed from the domed enclosure to simplify
installation and service. The cameras can be either
suspended or in a pendant mount. The camera/lens modules
are available in two versions, the in-ceiling AutoDome kit for
PAL/NTSC and pendant AutoDome kit, including wall mount
for PAL/NTSC.
www.boschsecurity.com
Technical Specifications
Camera type
TV standard
Power
Clear bubble
Power supply
G3ACS5C
G3ACPW2CW
In-ceiling
Pendant
PAL
PAL
24 VAC / 50 Hz
230 VAC / 50 Hz
Yes
Yes
No transformer includ- Transformer included in Wall
ed. Use PSU TC220PSX- mount
24
For more information about cameras, refer to the CCTV Data
Book
Ordering Information
G3ACS5C Color AutoDome Kit
18x color, indoor drop ceiling, clear dome, 24
VAC, 50 Hz
G3ACPW2CW Color AutoDome Kit
18x color, indoor pendant, wall mount, clear
dome, white, 230 VAC, 50 Hz
G3ACS5C
G3ACPW2CW
Bosch Security Systems B.V.
62 | Other Applicable Congress Products
LTC 0455 Series Color Camera
Electrical
LTC 0455/21
12 VDC
24 VAC
60 Hz
LTC 0455/51 230 VAC
50Hz
LTC 0455/61 120 VAC
60Hz
Power Consumption
Imager
10.8-39 VDC
NTSC
12-28 VAC
45-65 Hz
85-265 VAC
PAL
45-65 Hz
85-265 VAC
NTSC
45-65 Hz
4 W, excluding lens
Interline transfer CCD,
1/3-inch image format
Active Pixels
PAL Models
NTSC Models
Mechanical
Connectors
Features
X
1/3-inch format CCD imager
X
High sensitivity
X
Easy to install
X
Accepts AC or DC voltages
Introduction
The LTC 0455 series are compact rugged, 1/3-inch image
format digital color CCD cameras. They are ideal for
overview cameras in conference venues. Their superior
sensitivity, high resolution and picture quality provide
optimal performance in virtually all situations. The LTC 0455
cameras also come with a lens wizard that automatically
detects the type of lens installed and provides an OSD guide
that allows the installer to easily adjust the lens level and
focus without special tools or filters.
Functions
Bilinx Technology
The LTC 0455 series cameras incorporate Bilinx. Bilinx is a
bidirectional communication capability embedded in the
video signal of all Bosch Dinion cameras. With Bilinx
technicians can check status, change camera settings and
even update firmware from virtually anywhere along the
video cable. Bilinx reduces service and installation time,
provides for more accurate set-up and adjustment, and
improves overall performance. In addition, Bilinx uses the
standard video cable to transmit alarm and status messages,
providing superior performance without additional
installation steps.
Power
LTC 0455/11 and
LTC 0455/21
LTC 0455/51
LTC 0455/61
Camera mounting
Lens mounting
Dimensions
(H x W x D)
Weight
752 H x 582 V
768 H x 494 V
- Video Output: BNC
- Video/DC-iris connector: 4-pin EIA-J
Push type connectors, polarity independent,
isolated from video output terminals
2-wire power cord with Euro plug
2-wire power cord with polarized plug
Top and Bottom, 1/4-inch 20 UNC
C and CS
58 x 66 x 122 mm
(2.28 x 2.6 x 4.8 inch)
including connectors
0.45 kg (0.99 lb)
For more information about cameras, refer to the CCTV Data
Book
Ordering Information
LTC 0455/11 Color Camera
1/3-inch, 540 TVL, PAL, DSP, 12 VDC/24 VAC,
50 Hz
LTC 0455/21 Color Camera
1/3-inch, 540 TVL, NTSC, DSP, 12 VDC/24 VAC,
60 Hz
LTC 0455/51 Color Camera
1/3-inch, 540 TVL, PAL, DSP, 230 VAC, 50 Hz
LTC 0455/61 Color Camera
1/3-inch, 540 TVL, NTSC, DSP, 120 VAC, 60 Hz
LTC0455/11
LTC0455/21
LTC0455/51
LTC0455/61
Technical Specifications
Electrical
Model No.
LTC 0455/11
Rated Voltage
12 VDC
24 VAC
50 Hz
Voltage Range
10.8-39 VDC
12-28 VAC
45-65 Hz
Bosch Security Systems B.V.
System
PAL
www.boschsecurity.com
Other Applicable Congress Products | 63
MON152CL 15-inch Color LCD
Flat Panel Display Monitor
Electrical
Aspect Ratio
Mechanical
Cabinet
Dimensions
LCD Panel with Base
(W x D x H)
LCD Panel Only (W x D x H)
Weight
4:3
Material: ABS94V0 plastic
Finish: Charcoal
391 x 183 x 395 mm
(15.4 x 7.2 x 15.6 in.)
391 x 70 x 306 mm (15.4 x 2.75 x 12 in.)
LCD panel with base: 4.9 kg (10.8 lb)
LCD panel only: 3.6 kg (8.0 lb)
For more information about monitors, refer to the CCTV
Data Book
Ordering Information
Features
X
Provides 500 TV lines of resolution
X
Y/C (S-video) and loop-through video and audio inputs
X
Analog VGA input
X
Space saving, compact design
X
50% Less power consumption than conventional CRT
monitors
X
NTSC and PAL formats
X
Picture-in-picture feature
X
Universal power source
X
Front panel control lockout
X
On-screen display (OSD) for setup and adjustment
MON152CL 15-inch Color LCD Flat Panel Display Monitor
38 cm (15 in.), PAL/NTSC, 500 TV lines of high
resolution, PIP, CVBS, VGA and audio, 120/
230 VAC, 50/60 Hz
MON151PS Power Supply
for remote powering of one (1) MON151CL, or
one (1) MON152CL or for one (1) MON171CL,
120/230 VAC, 50/60 Hz
MON151RK Rack Mount Kit
for one (1) MON151CL or for one (1)
MON152CL; Height: 31.12 cm (12.25 in.),
Width: 48.26 cm (19 in.)
MON152CL
MON151PS
MON151RK
Introduction
The MON152CL is a high-resolution, high performance liquid
crystal display (LCD) video monitor. It can be used as an
operator display with the DCN Automatic Camera Control
software. Available in an ergonomic, aesthetically pleasing
design, this state-of-the-art monitor includes a 38-cm (15inch) color thin film transistor (TFT) active matrix LCD panel
with 1024 by 768 pixels.
Technical Specifications
Electrical
Rated Voltage
Voltage Range
Power at Rated Voltage
Sync Format
LCD Panel
Screen Size (H x V)
Viewable Picture Area
Pixel Pitch (H x V)
Resolution
www.boschsecurity.com
120/230 VAC, 50/60 Hz
90 to 264
38 W
PAL/NTSC
TFT LCD
304.1 x 228.1 mm (12 x 9 in.)
38 cm (15 in.) measured diagonally
0.297 x 0.297 mm
1024 x 768 pixels; 500 TVL typical
Bosch Security Systems B.V.
64 | Other Applicable Congress Products
Bosch Security Systems B.V.
www.boschsecurity.com
| 65
D
DCN-DDB Data Distribution Board . . . . . . . . . . . . . . . . . 53
DCN-DDI Dual Delegate Interface . . . . . . . . . . . . . . . . . . 42
DCN-DISBCM Buttons Chairman (10 sets) . . . . . . . . . . 16
DCN-DISBDD Buttons Dual Use (10 sets) . . . . . . . . . . . 17
DCN-DISR Rims for Discussion Units . . . . . . . . . . . . . . . 16
DCN-FCS Flush Channel Selector . . . . . . . . . . . . . . . . . . 49
DCN-FEC Flush End Cap (50 pcs) . . . . . . . . . . . . . . . . . . 50
DCN-FHH Hand Held Microphone . . . . . . . . . . . . . . . . . . 44
DCN-IDESK Interpreter Desk . . . . . . . . . . . . . . . . . . . . . . 35
DCN-MICS/L Pluggable Microphone
Short/Long Stem . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 37
DCN-SWSMV Synoptic Microphone and Voting
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DCN-WAP Wireless Access Point . . . . . . . . . . . . . . . . . . . 19
DCN-WCCU Wireless Central Control Unit . . . . . . . . . . . 20
DCN-WCH05 Charger for 5 Battery Packs . . . . . . . . . . . 24
DCN-WD-D Wireless Discussion . . . . . . . . . . . . . . . . . . . . . 9
DCN-WDD-D Wireless Dual Discussion . . . . . . . . . . . . . . 11
DCN-WDV-D Wireless Discussion Voting . . . . . . . . . . . . 13
DCN-WFCCCU Flight Case for CCU and WAP . . . . . . . . 25
DCN-WFCD10 Flight Case for 10 Wireless Discussion. 25
DCN-WLIION-D Battery Pack for Wireless Discussion . 23
DCN-WPS Power Supply for Wireless Discussion . . . . . 17
LBB 4416 Series Optical Network Cables . . . . . . . . . .
LBB 4417/00 Set Network Connectors (20 pcs). . . . .
LBB 4418/00 Cable Connector Tool Kit . . . . . . . . . . . .
LBB 4419/00 Cable Couplers (10 pcs) . . . . . . . . . . . . .
LBB 9095/30 Interpreter Headphones . . . . . . . . . . . . .
LBB 9600/20 Condenser Handheld Microphone . . . . .
LBC 1215/01 Microphone Clamp . . . . . . . . . . . . . . . . . .
LBC 1221/01 Floor Stand . . . . . . . . . . . . . . . . . . . . . . . .
LBC 1226/01 Adjustable Boom . . . . . . . . . . . . . . . . . . .
LBC 1259/00 Universal Floorstand . . . . . . . . . . . . . . . .
LTC 0455 Series Color Camera . . . . . . . . . . . . . . . . . . .
LTC 5136 Autodome Controller . . . . . . . . . . . . . . . . . . .
LTC 8200 Allegiant Video Switcher . . . . . . . . . . . . . . . .
LTC 8555/00 Allegiant Keyboard . . . . . . . . . . . . . . . . . .
56
56
57
57
34
45
47
47
48
26
62
60
58
59
M
MON152CL 15-inch Color LCD Flat Panel Display
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
P
PRS-4DEX4 Audio Expander Digital . . . . . . . . . . . . . . . . 38
E
Example 1 - Discussion . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example 2 - Electronic Voting . . . . . . . . . . . . . . . . . . . . . . .
Example 3 - Interpretation . . . . . . . . . . . . . . . . . . . . . . . . .
Example 4 - Camera Control . . . . . . . . . . . . . . . . . . . . . . . .
5
6
7
8
G
G3A Series AutoDome System . . . . . . . . . . . . . . . . . . . . . 61
H
HDP-ILN Induction Loop Neckband . . . . . . . . . . . . . . . . . 33
I
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
L
LBB 3015/04 High Quality Dynamic Headphones . . . . . 33
LBB 3441/10 Under the Chin Headphones . . . . . . . . . . 31
LBB 3442/00 Single Earphone . . . . . . . . . . . . . . . . . . . . . 31
LBB 3443 Lightweight Headphones . . . . . . . . . . . . . . . . 32
LBB 3555/00 DCN Intercom Handset . . . . . . . . . . . . . . . 43
LBB 4116 Series DCN Extension Cables . . . . . . . . . . . . 50
LBB 4117/00 DCN Cable Locking Clamp (25 pcs) . . . . 51
LBB 4118/00 DCN Termination Plug . . . . . . . . . . . . . . . . 51
LBB 4119/00 DCN Connectors (25 pairs) . . . . . . . . . . . 52
LBB 4402/00 Audio Expander . . . . . . . . . . . . . . . . . . . . . 39
LBB 4404/00 CobraNet Interface . . . . . . . . . . . . . . . . . . 41
LBB 4410/00 Optical Network Splitter . . . . . . . . . . . . . . 54
LBB 4414/10 Fiber Interface Without Address . . . . . . . 55
www.boschsecurity.com
Bosch Security Systems B.V.
1 | DCN Wireless Discussion System
Tradition of quality and innovation
For over 100 years, the Bosch name has stood
for quality and reliability. Bosch Security
Systems proudly offers a wide range of fire,
intrusion, social alarm, CCTV, management
and communication systems and components
to help you find the solution for any application.
We are the global supplier of choice for
innovative technology backed by the highest
level of service and support. When you need
solutions you can rely on, choose Bosch.
Bosch Security Systems
For further information see
www.boschsecurity.com
or send an e-mail to
emea.securitysystems@bosch.com
© Bosch Security Systems, 2007
Printed in The Netherlands
Modifications reserved
CO-EH-en-05_F01U517474_04