Mitsubishi Electric WD-82CB1 Operating instructions

MITSUBISHI
ELECTRIC
3D DLP®HOME-CINEMA TELEVISION
MODELS
740 Series
840Series
WD-82CB1
BASIC OWNER'S GUID
This manual provides basic connection, setup, and operating instructions. For use of additional features of this television, please visit our website at www.Mitsubishi-tv.com
to view or download a supplemental Owner's Guide. Follow the Support link to the Product Documents page.
•
For questions:
Visit our website at www.mitsubishi-tv.com.
E-mail us at TVsupport@mevsa.com.
Call Consumer Relations at 800-332-2119 for operational or connection
•
For information on System
•
To order replacement
800-553-7278.
assistance.
Reset, please see the back cover.
or additional remote controls, visit our website at www.mitsuparts.com
H;S3mll °
HIGH'DEFINITION
MULTIMEDIA
INTERFACE
6COLOR
_ glWIIglglgl_i
P R O C E S S O R
INTERNETMED_A
or call
2
FCC Declaration
RISK OFELECTRICSHOCK
DONOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the
user of the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying the product.
MAINS DISCONNECTION:
The mains plug is used
as the disconnect device. The mains plug shall remain
readily operable.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
Cet appareil ne doit pas etre expose A des gouttes ou
A des eclaboussures et aucun objet rempli d'un liquide,
comme un vase, ne doit etre place sur I'appareil.
WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.
TV WEIGHT: This TV is heavy. Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and disconnect all cables before moving it.
Stand Requirement
CAUTION: Use these Mitsubishi TV models only with
the Mitsubishi stand model shown here. Other stands
of Conformity
Product:
Projection Television Receiver
Models:
WD-73740, WD-82740
WD-73840, WD-82840, WD-92840
WD-82CB1
Responsible
Party:
Mitsubishi Electric Visual Solutions
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
Telephone:
1 (800) 332-2119
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by
Mitsubishi could cause harmful interference and would
void the user's authority to operate this equipment.
can result in instability and possibly cause injury.
Canadian
Mitsubishi does not design, manufacture or sell matching
bases for 82-inch and 92-inch model televisions. When
For Model WD-82CB1
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe Best conforme
A la norme NMB-003 du Canada.
selecting a stand, base, or other furniture to support the
TV, please make sure it is designed with the appropriate
dimensions for stability and to support the TV's weight plus
the weight of any additional equipment you plan to store.
Custom cabinet installation must allow for proper
air circulation around the television.
For assistance
call 1(800) 332-2119
Notice
Note: Features and specifications described in this
owner's guide are subject to change without notice.
3
Contents
Important
Cleaning
Safety Instructions
................
4
Normally, light dusting with a dry, non-scratching
duster will keep your TV clean. If cleaning beyond this
is needed, please use the following guidelines:
5
First, turn off the TV and unplug the power cord from
the power outlet.
Basic Setup and Operation
Package Contents
.......................
Installing the Remote Control Batteries .........
TV Overview ...........................
5
5
Before You Begin ........................
Remote Control .........................
5
6
Setting Up and Using TV Inputs ..............
7
Basic TV Operation .......................
TV Menus ............................
9
11
Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using a
vacuum cleaner with a brush attachment.
Top and Sides of the TV
•
2 TV Connections
Before You Begin .......................
Connection Types and Audio/Video
Recommendations
Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel, microfiber, or a clean
cloth diaper, lightly moistened with water. Dry with
a second dry, soft, non-abrasive cloth.
12
Quality
....
12
Input and Output Jacks ...................
13
Connection
13
Diagrams ....................
3 TV Features
StreamTV
TM
Internet .....................
17
3D Video .............................
20
Wireless Audio Playback (840 Series) .........
22
Sound Projector (840 Series) ...............
23
For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water
used to moisten the cloth. Rinse with a second
cloth moistened only with water. Dry with a third
dry, soft, non-abrasive cloth.
Appendices
Appendix A: Auto Input Sensing ............
Appendix
B: Lamp-Cartridge
Replacement
Appendix
C: Troubleshooting
..............
26
....
27
Screen
29
•
Mitsubishi
TV Software ....................
32
Warranty
..............................
36
MEVSA Internet
Applications Policy ..........
39
•
•
•
Follow the instructions for the top and sides, wiping
gently in an up and down motion.
Clean the entire screen evenly, not just sections of
the screen.
Do not allow liquid to drip down the screen, as
some liquid may enter the TV through the gap
between the screen and screen frame.
You may purchase Mitsubishi Screen Cleaner,
part number CLEANER-VSS, by calling
1 (800) 553-7278.
General Cleaning Precautions
TV Software
•
•
Do not attempt to update the software of this TV
with software or USB drives not provided by or
authorized by Mitsubishi Electric Visual Solutions
America, Inc. Non-authorized software may damage
the TV and will not be covered by the warranty.
Automatic software updates will be downloaded
over the internet to the TV if StreamTV is set up and
connected to the internet. In Canada, WD-82CB1
users can receive automatic software updates
although StreamTV services will be unavailable.
•
DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
•
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
•
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
•
DO NOT spray liquids or cleaners directly on the
TV's surfaces.
DO NOT scrub or rub the TV harshly. Wipe it
gently.
For assistance
call 1(800) 332-2119
4
Important
Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
1)
Read these instructions.
2)
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
OF ANTENNA
GROUNDING
ANTENNA
I1,1 "_
--_
Do not use this apparatus near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
jANTENNA
y
_""
5)
DISCHARGE
I
(NEC
/.,._ j
LEAD IN WIRE
(N_NDURCT 0 LRS 810-21,
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
T_"_POWER
CLAMPS
SERVICE
ELECTRODE
NATIONAL
Outdoor
E LECTRICAL
Antenna
CODE
810-20)
GROUNDING
1_
_='-
NE C --
UNIT
ARTICLE
_GROUND
8) Do not install near any heat sources such as
11) Only use attachments/accessories
manufacturer.
EXAMPLE
(NEC
ART
GROUNDING
SYSTEM
250,
PART
H)
Grounding
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.
Replacement
Parts
When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
specified by the
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDERIS
PROVIDEDTO CALLTHE CATVSYSTEMINSTALLER'SATTENTION TO ARTICLE820-40 OFTHE NECTHATPROVIDES
GUIDELINESFORTHE PROPERGROUNDINGAND, IN PARTICULAR, SPECIFIESTHATTHE CABLEGROUNDSHALL BE CONNECTEDTO THE GROUNDINGSYSTEMOF THE BUILDING,AS
CLOSETO THE POINTOF CABLEENTRYAS PRACTICAL.
13) Unplug this apparatus
during lightning storms or when unused for long
periods of time.
To Order a Replacement
Lamp Under Warranty
Call (800) 553-7278. Please have model number, serial
number, and TV purchase date available.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
For assistance
call 1(800) 332-2119
Lamp Replacement
For lamp-replacement
instructions,
see Appendix
B.
To Purchase a Replacement
Lamp After Warranty
Visit our website at www.mitsuparts.com
or call
(800) 553-7278. Order new lamp part number
915B455011.
Children and TV Viewing
The American Academy of Pediatrics discourages television viewing for children younger than two years of age.
1BasicSet
and
tion
TV Overview
Package Contents
Please take a moment to review the following list of
items to ensure that you have received everything.
Sample TV controls and
location of the STATUS
indicator. See page 31.
Remote
Control
Two AA
Batteries
Basic
Owner's
Guide
Quick
Setup
Guide
Product
840 Series.
Calibration
Registration
Card
Connection
Jacks
Microphone
.Lamp-Compartment
Door
f
Installing the Remote Control
Batteries
1,
TV Control
Buttons on the control panel duplicate some keys on
the remote control.
Remove the remote control's back cover by
gently pressing in the tab and lifting off the cover.
To display the main menu, press INPUTand VOL+simultaneously for about 10 seconds. Press and hold INPUT
and MOL+for 10 seconds to clear the menu.
Load the batteries, making sure the polarities
(+) and (-) are correct. For best results, insert
the negative (-) end first.
3,
Panel
System Reset
Snap the cover back in place.
If the TV fails to respond to the remote control, the
control-panel buttons, or will not power on/off, perform
System Reset. Press and hold the POWERbutton on the
control panel for ten seconds.
The remote
control
requires two
AA batteries.
Before You Begin
1,
Review the important safety, installation, and operating information at the beginning of this book.
Choose a location for your TV.
®
•
•
JJiIl_
•
See the stand requirements on page 2.
Allow at least four inches of space on all sides
of the TV to help prevent overheating. Overheating may cause premature failure of the TV.
Avoid locations where light may reflect off the
screen.
3,
Install the batteries in the remote control.
4°
Plug the TV into an AC power outlet.
For assistance
call 1(800) 332-2119
6
1. Basic Setup and Operation
Remote Control
Aim the remote control at the TV screen. The
Sleep Timer. Automatically turns off
the TV after the number of minutes
you set.
TV can detect control signals over the entire
screen area.
Number/letter keys
Channel tuning, page 8
Pass-code entry
TOOLSkey shortcuts
Powers TV on or off.
Adds a separator in digital channel
numbers. Clears some menu entries.
Returns to the previous channel.
In menus, steps back one menu.
Mutes the TV speakers.
Displays up to nine favorite
sources.
Displays shortcuts for the number keys.
Press to check if shortcuts are available
for the current device.
VOL Controls volume of TV speakers.
Changes picture shape,
page 10
CH Changes channels; moves to another
PAGE
page in a menu or list.
Connects to internet content,
page 17.
®
Press to select a TV input,
page 8.
Selects a channel number or menu item.
Navigation and adjustment controls
@
@
ChannelView channel listings. Set the
TV clock to receive correct updates.
Video settings
Displays or clears the TV main
menu (page 11). Also steps
back one menu.
TV status or TV help
(_)
Audio settings
Clears all menus and on-screen
displays.
(PAUSE)Freezes a broadcast TV picture
from the ANT (antenna) input.
Playback controls for StreamTV internet services. May apply to compatible devices under HDMI control. See
F1-F4. Function keys for some
StreamTV internet services.
the supplemental Owner's Guide at
www.mitsubishi-tv.com
for setup of
HDMI control.
Mitsubishi iPhone App
Visit the iTunes store for a free app
that turns your Apple iPhone, iPad,
or iTouch into a second remote
control for the TV.
Picture shortcuts
The TOOLS Key and Menu
Press the TOOLSkey to see the Tools menu. Press
number keys to activate shortcuts. Your Tools menu
may differ from the sample, depending on your setup.
•
•
Shortcuts specific to the current device are in the
third column.
Shortcuts may be available for a CEC-enabled
device. See the supplemental Owner's Guide at
www.mitsubishi-tv.com.
For assistance
call 1(800) 332-2119
I
Sound
shortcuts
PICTURE SOUND
I Briqht
I
m 2 _ub I
i woomr t
I Naturall
1_Surroundl
I
INiahtl
TV
....
Device-Specific Shortcuts
Availability varies, depending on equipment features
and setup.
3 CC. Turns closed captions
on/off (ANT and Y composite
_ut_
3D
I
Sample Tools menu, 840 series
on!_
1. Basic Setup and Operation
7
First-Time Power-On
1,
Install batteries in the remote control.
See page 5.
Welcome
Aim the emitter (bulb)
end of the remote control
at the TV and press the
POWERkey (_). Wait for the
Welcome screen.
If you wish to change the
menu language to Espa_ol,
press • then ENTER.
3_
energy-mode selections.
Select Home.
Press • to highlight EXIT.
Press ENTERto clear the menu.
5_
•
Mitsubishi recommends the Home setting,
which produces a picture suitable for home
viewing and uses less power.
•
The Retail setting looks best under the bright
lighting often found in commercial settings. In
this mode, the TV uses more power than when
in the Home setting.
This table compares energy choices offered in the
Welcome screen.
Press • to move to the
4_
Screen Energy Options
Picture Mode
Bright
Lamp Energy
Standard
Brilliant
Bright
Use the Picture > Video menu to change the
Picture Mode.
Use the Setup > Energy menu to change
Lamp Energy.
Setting Up and Using TV Inputs
The ANT (Antenna)
4_
Input
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV's
ANT input. Refer to page 15.
You must perform a channel scan to enable reception of digital channels. If you skip this step, the TV
can receive only analog channels. The channel scan
will search for high-definition and standard-definition
channels available in your area. Note: Direct cable
service will not include scrambled or premium channels.
Memorizing
1,
Channels with Channel Scan
(no cable box). Press ENTERto add a
check.
5_
Select the scan type.
•
For first-time setup, highlight All channels.
•
To scan for channels not already in memory,
highlight Add only new channels.
Press
ENTERto add a check.
&
Highlight Scan and press ENTER.
Channel memorization may take up
to 15 minutes to complete.
Power on the TV.
Press MENUand open the Setup > Channel
Highlight Ant Air if connected to an
over-the-air antenna. Highlight Ant
Cable for service over direct cable
menu.
To stop channel memorization
press CANCEL.
before completion,
At any time after Channel Scan,
Start channel memorization
menu.
3,
•
Use the Setup > Channel > Edit menu to add or
delete individual channels from memory.
•
Repeat the All channels scan if you reposition the
antenna or move the TV to a new geographic area
with a different channel line-up.
from the Setup > Channel
Press • to enter the menu.
For assistance
call 1(800) 332-2119
8
1. Basic Setup and Operation
Setting Up and Using TV Inputs, continued
Setting
Up Inputs with Auto Input Sensing
More About the Input Selection Menu
Connection information starts on page 12. Learn more
about Auto Input Sensing on page 26.
•
To assign helpful names to the icons, see the
Inputs > Name menu.
1,
•
To remove unwanted Antenna, Bluetooth®, or HDMI
device icons from the Input Selection menu, see
the Inputs > Name menu.
•
To rearrange the icons, use the Inputs
menu.
Power on the TV.
Power on the devices to ensure detection.
3°
Connect one device to the TV, making note of the
TV input jack.
The TV will display the New Device Found screen if
the connection type is detectable.
4°
Highlight the device type in the on-screen list and
press ENTER.The name you select here will appear
in the Input Selection menu.
> Order
Detailed information on using these menus
is in the supplemental Owner's Guide at
www.mitsubishi-tv.com.
Watching
Broadcast TV
TV Connected
to an Antenna or Direct Cable
Service (no cable box)
Note: Perform channel memorization to enable reception of digital channels. See page 7.
1,
Press INPUTto display the Input Selection
menu.
Highlight the antenna or cable icon and press ENTER.
Sample New Device Found screen.
5,
Press EXITto close the New Device Found screen.
&
Repeat the preceding steps for each additional
device you want to add.
Sample Input Selection menu, antenna input selected
3° To tune to a channel from the ANT input, use any of
these methods.
•
Selecting
an Input to Watch
1° Press INPUT.
For a two-part digital channel, such as 3-1,
Press _ • and • to highlight an
input icon.
Sample Input Selection menu, DVD input selected
3°
press 3_1_.
•
Press (]_to
a time.
•
Press and hold |to
•
Press _
•
Use the Fav (Favorites) feature to tune to up to
nine favorite channels. See the supplemental
Owner's Guide at .
•
Press I-_to
Press ENTERto switch to the input.
Note:
In most cases, to see a named icon for a connected device (as in the samples), you must first
assign a name either
•
•
When the device is first connected and the
New Device Found menu offers a choice
of names.
By using the Inputs > Name menu to
assign or change a name at any time after
the TV has detected the connection.
For assistance
Enter the channel number using the number
keys on the remote control and press _.
call 1(800) 332-2119
change channels one channel at
speed through channels.
to return to the previous channel.
display ChannelView channel
listings. Highlight a channel number, then press
_to
tune.
•
Set up ChannelView custom channel banks
and use the _
key to tune within predefined
groups of channels.
1. Basic Setup and Operation
9
Basic TV Operation
Audio Controls
Picture
Controlling Sound Volume
To get the best picture under different viewing conditions, set the Picture Mode first before changing other
video settings.
Press V0L to adjust the sound level of
the TV speakers.
1,
Settings
Press VIDEO.
Press • until the Picture Mode
option displays.
Changing Audio Settings
1,
8,
(TV Speakers
Only)
3,
Press AUDIO.
Press • to display the name of the
adjustment you want.
Brilliant
Under very bright lighting
Press •to
Game
With gaming consoles (inputs
named Game or PC only)
Bright
For most daytime viewing
Natural
For most nighttime viewing
change.
Using an External
Sound System
To switch from the internal TV speakers to an external
sound system:
1,
Press AUDIO.
Press • to display the TV Speakers
3,
Press • to make one of these selections:
option.
Press • to select either On (to hear sound from
the TV speakers) or Off (to hear sound from an
external sound system).
4,
Press • to display the name of another adjustment.
6,
Wait a few seconds and the display will clear.
Press •
• to make the adjustment.
More picture adjustments
can be found in these menus:
•
Picture > Video
See page 16 for suggestions on connecting your sound
system to the TV.
•
Picture > Picture Plus
•
Picture > 3D Mode
Disconnecting
•
Picture > Perfect (840 Series only)
an A/V Receiver
When you disconnect an A/V receiver, change the TV
Speakers setting to On to hear sound from the TV
speakers. Use the Sound > Audio > TV Speakers
menu.
HDMI Control
(CEC-Enabled
HDMI A/V Receiver)
The TV's remote control may control some functions of
the A/V receiver. See the supplemental Owner's Guide
at www.mitsubishi-tv.com.
For assistance
call 1(800) 332-2119
10
1. Basic Setup and Operation
Basic TV Operation,
continued
The FORMAT Key and Picture Shape
1
to cycle through picture
shapes for the current
image. The TV will
Press
the FORMAT
key you
remember
the format
last used on each input.
For more on TV formats and signal
types, see the supplemental Owner's
Guide at www.mitsubishi-tv.com.
Sample Uses of the FORMATKey
You can use the FORMATkey to display the image as originally intended or
to reduce or eliminate black areas at the edges.
/
/
High-definition signal with
squarish 4:3 image embedded.
The image is narrower than the
16:9 screen; unused areas at
the sides are filled with black.
Wide Expand mode stretches
the picture sideways to fill the
screen.
Press
Standard 2.35:1 anamorphic
DVD image; unused areas at
the top and bottom are filled
with black (letterbox effect).
Zoom mode. The picture fills
the screen. All four edges are
cropped in this mode.
More TV Features
See the supplemental
www.mitsubishi-tv.com
topics.
Owner's Guide at
for more on these and other
•
Parental controls (Lock menu). Requires first setting
a pass code.
•
TV Clock (Setup > Clock menu). Set the TV Clock if
you plan to use the TV Timer, ChannelView channel
listings, or the TV's Lock by Time feature.
•
ChannelView channel listings. Press the GUIDEkey to
view. See the supplemental Owner's Guide to create
custom collections of channels.
For assistance
call 1(800) 332-2119
•
Changing input names in the Input Selection
(Inputs > Name menu)
menu
•
HDMI control of other A/V devices (CEC)
•
Using theTV with a computer
•
840 Series. Using the TV speakers for center
channel sound for your external surround sound
system.
•
840 Series.
complement
Adding external rear speakers to
the TV's surround sound effect
•
840 Series.
Using an external subwoofer
1. Basic Setup and Operation
11
TV Menus
Picture
Video
Picture+
Reset
Perfect
Advanced
3D Mode
Basic picture settings
Press MENUon the remote control to open
the main menu. Find detailed descriptions
of all menus in the supplemental Owner's
Guide at www.mitsubishi-tv.com.
Specialized picture controls
Reset of sound and picture adjustments
for the current input
840 Series. Fine-tuning of color settings
Highly customized picture adjustments for each input. Mitsubishi
recommends
these adjustments
be
made only by a trained professional
installer.
Setup for 3D viewing. See page 20.
Inputs
Name
HDMI
Control
Order
StreamTV
Sound
Audio
Global
Auto SP
SoundPro
Basic audio settings
840 Series. Also includes subwoofer
and center-channel controls.
Demo
Update
840 Series. Sound Projector settings.
See page 23.
Setup
Menu language
Clock
Set the TV clock to use the TV Timer, to
use ChannelView listings, or to lock the
TV by time.
Timer
Setup for the TV Timer. The Timer tells
the TV to power on automatically at a
time you set. Set the TV clock before
using the TV Timer.
Network
Setup of icons in the Input Selection
menu
740 or 840 Series (U.S. only). Account
deactivation; clears your personal data
from the TV.
Demonstrations
of selected TV features
Instructions for updating TV software.
740 or 840 Series (U.S. only). Controls
to limit TV use by content ratings (composite video and antenna inputs only)
Time
Setup to lock the TV by time of day. Set
the TV clock before using this menu.
Channel
Setup to lock specific channels (antenna
input only)
Settings for closed captions
Energy
Setup for HDMI Control (CEC) of external devices
Lock
Captions
Channel
for TV inputs
840 Series. Settings for the AVR/REAR
OUTPUT jack.
Parental
Language
Name assignments
Panel
Control-panel
lock
Other
740 or 840 Series (U.S. only). Controls
to limit TV use based on rating systems
that may come into effect in the future
(digital channels on the antenna input
only)
Setup for a channel scan on the ANT
input; addition to or deletion of channels
from TV memory
Controls for TV energy usage
Setup for internet connectivity. See page 17.
For assistance
call 1(800) 332-2119
2 TVConnections
Before You Begin
Auto Input Sensing
Surround Sound
The TV's Auto Input Sensing feature automatically recognizes many connections and prompts you to identify
the type of device connected. See pages 8 and 26 for
more on Auto Input Sensing.
The TV accepts PCM stereo or Dolby Digital 5.1 over
the ANT and HDMI inputs and passes the audio out on
the DIGITAL AUDIO OUTPUT jack.
Connection
Types
Use the connection types available on your input
devices that will give the best video quality. For
example, choose HDMI over component video; choose
component video over composite video.
Picture Quality
For best picture quality, route signals directly from the
source device to the TV.
Connection Types and Audio/Video
Quality
VIDEO QUALITY
HDMI
DVI-to-HDMI
Component
Video
®®®
Composite
Video
®
HDMI
Digital
Coaxial Audio
L/R Analog
Audio
®®
l l
For assistance
call 1(800) 332-2119
Stereo
Mini
Plug
®
2. TV Connections
Input and Output Jacks
13
AUDIO/SURROUND OUTPUT
CENTERINPUT
SUBWOOFEROUTPUT
See the Supplemental
www.mitsubishi-tv.com
EXTERNAL CONTROLLER INPUT
Accepts control
signals from an
external controller
or IR repeater when
set up by your professional installer.
,I
AUDIO/SURROUND
Y
R
-OUTPUT-
1
2
3
Composite
video input
(page 15)
I
)',
I
I
DIGITAL
l
" ........
-_',_lofferedonthe__R
HDMI
__t l
I
........ _,840 series.
I
DIGITAL
AUDIO
OUTPUT
(page 20) (page 16)
. ..........
I
I
3D
GLASSES
EMITTER
ANT
Coaxial antenna
input
(page 15)
l
FAdditionaljacks
Owner's Guide at
for use of these jacks.
I
I
I
I
I
I
I
I
CENTER
SUB WOOFER
INPUT
OUTPUT
I
I
I
I
I
I
I
I
usB USBIp
I
III
I
3D
DVI/PC
GLASSES AUD O
EMITTER INPUT
ANT
LAN
4
--Y Pb Pr
Component
video input
(page 14)
@®
I
HDMI
(page 13, page 16)
Inputs are HDMI
HDCP compliant.
USB/USB-P
The left USB port can
accept a wireless network
adapter. See page 18.
DVI/PC
L Calibration
INPUT
Audio
input
(page 15)
Microphone
Input
(840 series,
page 23)
• 840 Series. The right
USB port can power a TV
LAN
accessory such as a wireless subwoofer.
(Ethernet, port
page 17)
HDMI-4 offered
on the 840 series.
L/R
Analog stereo
audio inputs
Connection Diagrams
HDMI Device
Examples: HDTV Cable Box, Satellite Receiver,
or DVD/Blu-ray Player
Required:
HDMI cable.
TV jack panel
Connect an HDMI cable from the TV to the device's
Any device with
HDMI output
HDMI output. HDMI-connectable devices provide
video and audio through a single cable.
HDMI
cable
Mitsubishi recommends using high-speed HDMI cables
to connect newer devices incorporating HDMI technology. See "HDMI Cable Categories" on the opposite page
for more on HDMI cable types.
Note:
This connection carries high-definition video,
3D video, and Dolby Digital 5.1 audio signals.
This connection
(HDCP).
supports copy protection
IIIIIID
!
Incoming from
cable service or
satellite dish
SATELLITE
IN
For assistance
call 1(800) 332-2119
14
2. TV Connections
Y Pb Pr Component
Video Device
Examples: HDTV Cable Box, Satellite Receiver,
or DVD/Blu-ray Player
If your source device has an HDMI output, use the connections for an HDMI device described on the previous
page instead of component video.
TV jack panel
Required:
Component video cables
RCA-type analog audio cables
Note:
•
This connection
signals.
•
carries high-definition
Component
video device
video
Audio
cables
To hear digital surround sound from an A/V
receiver, connect the digital audio output from the
device directly to your digital A/V receiver.
Component
video cables
IN or
SATELLITE IN
|miNi
VCR or DVD Recorder to an
Antenna or Wall Outlet Cable
Incoming from
• cable service or
satellite dish
_
]IGITAL
H_m(
Required:
•
Video cables
Component video cables (red/
blue/green)
or
•
•
•
panel
Composite video cable (usually
yellow)
RCA-type analog audio cables
Two-way RF splitter
Two coaxial cables
Note:
•
Use composite video only
if component video or
HDMI are unavailable. A
composite video connection
cannot carry high-definition
video signals.
•
If your recording device has
an analog-only tuner, you
must use a digital converter
box to enable recording of
digital broadcasts.
Audio
cables
DVD Recorder
or VCR
For assistance
call 1(800) 332-2119
Component
video cables
2. TV Connections
15
DVI Video Device
Examples: Computer
or Older A/V Device
Note:
This connection
signals.
can carry high-definition
The HDMI connection
(HDCP).
video
TV panel
supports copy protection
Connect a DVI device (digital only) to one of the TV's
HDMI input jacks.
Required:
Audio cable with stereo mini-plug
DVI-to-HDMI cable or DVI/HDMI adapter and HDMI
cable
Digital DVI
device
DVI-to-HDMI
cable
Some devices require a connection using an analog
output first in order to view on-screen menus and to
select DVI as the output. Please review your equipment
instructions for DVI connectivity and compatibility.
Antenna
or Cable TV Service
Connect the incoming cable to the TV's ANT input.
Reception over direct cable (no box) is limited to nonscrambled analog and digital channels.
Audio cable
Composite
Video Device
VCR or other device with composite video
output
Note:
This connection does not support high-definition video signals.
Required:
Corn posite video cable (usual Jyyellow)
RCA-type analog audio cables
TV panel
H_3_MJ+
_Nr
G_+
Dr,Pc
AU_U
UHF/VHF
antenna
or
Directcable(nocablebox)
or
cable
box
Notrecomrneded.
Otherconnectiontypesprovide
betterquality
audioandvideo.
AUDIOOUT
®=
Composite
video cable
COMPOSITE
For assistance
call 1(800) 332-2119
16
2. TV Connect_ns
A/V Receiver
A/V Receiver
Most setups require either a digital audio cable or
analog stereo audio cables. To send audio from TV
channels received on the ANT input or devices connected directly to the TV, you must use one of the connections shown below.
Required:
with HDMI
Output
One HDMI cable
This option allows you to view and hear content from
devices connected to an A/V receiver. The A/V receiver
can send audio and video to the TV over a single HDMI
cable.
The TV makes all incoming audio available as an output:
•
Analog incoming audio is available as output in
digital stereo format on the DIGITAL AUDIO OUTPUT
jack. 840 Series. Analog incoming audio is also
available as analog stereo on the AUDIO/SURROUND OUTPUT jacks.
•
Digital
on the
Digital
output
incoming audio is available as digital audio
DIGITAL AUDIO OUTPUT jack. 840 Series.
incoming audio is also available as analog
on the AUDIO/SURROUND OUTPUT jacks.
You can add an optional audio connection from the
TV's audio output. The optional audio connection
allows you to hear, through the A/V receiver, devices
connected to the TV only, e.g., an antenna on the ANT
input.
See page 9 for tips on using an external sound system.
See page 9 for tips on using an external sound system.
TV
TV
f
840 Series
only
HDMI
cable
or
III
AUDIO
®
OPTICAL =......................
,IP_.'_
ii![;]iii
COAXIAL
O
INPUT
A/V receiver back panel
Note:
On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from the
TV as a digital signal. To hear these copy-protected signals through the A/V receiver, use the
connection for an analog A/V receiver.
Check the A/V receiver's Owner's Guide for
information on use of the digital input and
switching between digital sound and analog
stereo sound from the TV.
For assistance
call 1(800) 332-2119
If your A/V receiver converts
all video signals for output
on HDMI, you can use any
connection types from
external devices; content
can be HD or SD video.
Optional
analog or I
digital audiol
connection o
3 TVFeatures
StreamTV
Internet
TM
About StreamTV
2,
Open the Setup > Network
tings.
menu to review set-
740 and 840 Series, U.S. only
Internet services let you access many popular on-line
applications providing both free and paid content.
Required for StreamTV internet media:
•
•
•
•
Broadband internet service (at least 2 Mbps for SD,
4 Mbps for HD, and 8 Mbps for 1080p HDX)
Category-5 Ethernet cable or a wireless router
transmitting to an AzureWave AW-NU231 USB wireless adapter.
Computer access to the websites of content providers when initial account activation is required for
service.
A credit card to cover the cost of paid content.
WD-82CB1
Setup > Network, DHCP connection
3°
Press [-_
Manual
Note:
(Canada)
StreamTV internet services are unavailable in Canada.
Canadian users can, however, receive software updates
and use the iPhone remote control app noted on page
6. Follow the instructions on these pages to connect
the TV to your home internet network.
to clear the menu.
Manual setup is available only for a wired connection.
1° Connect the TV to your network router with a Category-5 Ethernet cable (not supplied).
2° In the Setup > Network
menu, highlight Manual
and press _.
3° Press • to move to the Connection
Home
Network
Setup
Before using StreamTV internet media, you must
connect the TV to the internet using either an Ethernet
cable or a wireless connection as described here.
Note:
840 Series. Make sure the TV is on any input
other than Bluetooth®. Press the INPUTkey to
change.
Data area.
4° Input the connection data.
5° After entering connection data, press _to
connect.
6° Change any of the following if needed:
•
•
•
Default Gateway
DNS
Subnet Mask
Wired Ethernet Connection
DHCP (automatic)
1,
Connect the TV to your network router with a Category-5 Ethernet cable (not supplied).
TV Panel
Router or modem
incoming providing high-speed
internet,
internet service
came "_
Ethernet
For assistance
call 1(800) 332-2119
18
3.
StreamTV
TM
TV Features
Internet, continued
network. Press CH/PAGEto see more networks if the
list fills more than one screen.
Wireless Connection
The TV requires an AzureWave AW-NU231 USB wireless
adapter to communicate with your IEEE 802.11n-compliant wireless network router. The adapter is available from
your Mitsubishi dealer or go to www.mitsubishi-tv.com
and follow the Accessories link.
1,
Disconnect
the Ethernet cable if present.
2,
Connect the wireless adapter to the TV's USB port.
Setup > Network menu after connecting. The active
network is checked and connection data displays.
5°
If connecting to a secure network, enter the
network key or password when prompted. Special
remote control keys you may need:
1
Wireless
adapter
CANCEL •
•
IEEE 802.11 n-compliant wireless
network
router providing
high=speed internet service
Connect the USB adapter to the USB port on the back
of the TV. 840 Series. Use the left USB port.
3°
Open the Setup > Network menu. After a few
moments, detected networks will appear listed on
the screen in order of signal strength.
Digit 1 and special characters
!@#$% ^*_-+=.SPACE?
• •
6,
Clears the password box of an old
entry from a prior session.
Deletes one character during password entry.
Toggle between upper and lower case
Press ENTERto connect.
Using StreamTV Internet Media
1,
2,
840 Series. After establishing internet connectivity
as described in "Home Network Setup," page 17,
switch the TV to any input other than Bluetooth®.
Press the INTERNETkey to display services.
3°
Press ENTERto launch an application.
Troubleshooting
If You Are Unable to Connect to the Internet
Check all power and data connections.
Setup > Network menu, wireless connection
4°
Highlight the desired network and press ENTERto
connect. A check will appear next to the connected
If you can reach the internet with a computer or
other device on the same internet service used by
the TV, consult the router or modem owner's guide
for reset instructions.
If you cannot reach the internet, contact your
service provider. You may be asked for network
information such as the TV's IP address. Go to the
Setup > Network menu to see connection data.
For Further Assistance
If you are having trouble connecting your TV or accessing internet applications, contact Mitsubishi Customer
Care at 1 (800) 332-2119.
For assistance
call 1(800) 332-2119
3.
StreamTV
TM
puter to go to www.VUDU.com/activation.
credit card is required for activation.
U.S. only)
Internet services provided by VUDUTM Apps let you
access many popular on-line applications. In addition
to free content, VUDU's movie service lets you buy and
rent movies through the TV. Visit www.VUDU.com
to learn more about available movie titles, prices, and
services offered.
Getting
1,
with VUDU
If you are having difficulty with your VUDU
account, contact VUDU Customer Care at
www.VUDU.com/support.
Other VUDU Support
Movies
After establishing internet connectivity as described
in "Home Network Setup," page 17, switch the TV to
any input other than Bluetooth®.
3,
Press the INTERNETkey to display services from
VUDU Apps.
Select the VUDU movie service.
4,
Browse the VUDU movie catalog and offerings.
A
Once your account is activated, you can rent and buy
movies using only the TV and the TV's remote control.
From time to time you may notice changes to
the internet interface as new features are added.
Started
19
Internet, continued
VUDU (740 and 840 Series,
Note:
TV Features
Reset your VUDU
account password
Using a computer, go to
www.VUDU.com (reset
requires access to e-mail).
Reset your parental
controls pass code
Call VUDU Customer Care at
1-888-554-VUDU (8838).
When you are ready to rent or buy a movie, you
will be prompted to activate your VUDU account.
Follow the on-screen instructions and use acom-
Using VUDU Apps and VUDU
Movies
Navigate VUDU's menus with the keys on the TV's
remote control. Browse the movie catalog, watch
movie previews, set parental controls, and rent or buy
movies.
Key functions vary according to context
and may change with newer versions of
VUDU.
Some VUDU screens include instructions
identifying available key functions.
/
..........
/
', J
..............
J
"
F
TOOLS. Use the Tools menu to perform A/V reset
while in VUDU movies or some VUDU Apps.
,
LAST.Goes to a previous screen.
CANCEL. Usually acts like the backspace key_
during text entry.
ENTER.Confirms a selection.
0H/PAGE. Jumps to the previous or next page of
menu items.
INTERNET.Displays the VUDU Apps internet menu.
Switch the TV to any input other than Bluetooth®
before connecting to the internet.
\
< I_J,V
•
Directional navigation
•
In VUDU Apps, press • • to display
more applications.
EXIT. Closes the current screen and goes to a
home screen.
GUIDE. In some contexts, returns to the
VUDU home menu.
INF0. In VUDU's movie service, displays
more options for the current selection if
available.
--Playback
keys.
F1. Displays a VUDU help menu if available.
, MITSUBISHI
F2. Displays the VUDU system menu if
available.
For assistance
call 1(800) 332-2119
20
3.
TV Features
3D Video
To display 3D content, your Mitsubishi TV requires:
•
Active-shutter 3D glasses compatible
of the following:
The TV's internal emitters
A matching external synchronization
connected to the TV's back panel
DLP link
Glasses compatible
are:
Using the TV's Internal
with any one
16ft.
Effective range of the
emitters in the vertical
emitter
I<
2s .
Emitters
t
and horizontal planes
with the TV's internal emitters
XPAND model 3DG-Xl03
Mitsubishi 3D TVs
IR glasses made for
16ft.
XPAND model X103 Universal IR glasses
For more information, visit the 3D TV page at
www.mitsubishi-tv.com.
A compatible 3D source device connected to the
TV via HDMI or StreamTV internet and outputting a
3D signal in one of these formats:
Frame Packing 1080p/24-Hz or 720p/60-Hz
Top-Bottom 1080p/24-Hz or 720p/60-Hz
Side-by-Side format, 1080p, 24/30/60-Hz;
720p, 60-Hz
Checkerboard format, 1080p, 60-Hz; (lower resolutions may be supported but will not fill the screen)
16ft.
Initial Setup
1,
Turns off 3D images; displays 3D content
as 2D (you may see two images).
Restores normal TV adjustment options
when viewing an ordinary 2D signal.
If your 3D glasses came with a synchronization emitter,
connect the unit to the 3D GLASSES EMITTER jack.
Place the emitter at the front of the TV where there is a
clear path to the glasses.
Note:
No emitter is required if using the TV's internal
emitters or DLP Link.
Automatic
•
•
Switches the TV to 3D mode and selects the
correct 3D format when the TV detects a 3D
signal from an HDMI 1.4a-compliant device.
Automatically switches the TV out of 3D
mode when receiving a normal 2D signal.
Connecting
2,
Power on the TV and the source device.
3,
Connect the source device to the TV's HDMI input.
4,
When the New Device Found screen displays,
name the input.
Press EXITto close the New Device Found screen.
5,
Choice of Source
Usethe Picture >3D Mode
menuto enable3D video.
For assistance
Formats
If your device is not HDMI 1.4a
compliant, you must choose the
correct setting from this list.
call 1(800) 332-2119
an external emitter
Depth
Adjusts the simulated 3D effect
applied to a 2D image. Available
only when Source Format is set
to 2D+ Depth.
3.
TV Features
21
3D Video, continued
Watching
Other Options in the 3D Menu
3D Video
Glasses
Control Off
Active 3D glasses are required. All glasses in use
at the same time must use the same control type.
Halogen lights, fluorescent lights, or direct sunlight can
interfere with operation of the glasses.
1,
Settings
Note:
°
2D+ Depth
Before watching 3D images from an internet
source, it is important to establish the internet
connection first before enabling 3D mode.
Press MENUand select the Picture > 3D Mode menu.
For Source Format, select Automatic
ENTER. Press EXITto close the menu.
°
If the image looks correct, the device is HDMI
1.4a compliant; always keep the setting at
Automatic for this device.
°
For non-compliant 3D sources, open the
Picture > 3D Mode menu and select a source
format based on how the picture looks:
Top/Bottom
Two images, screen
split horizontally
Notes on Using
When selected, generates a simulated 3D image from an ordinary
2D image. Adjust the effect using
the Depth setting. Requires use of
active-shutter 3D glasses.
the 3D video source is HDMI 1.4a compliant (picture may
still appear as 2D), the following limitations apply:
•
Picture adjustments are limited. To make picture
adjustments while watching normal 2D images from
the device, temporarily set Source Format to Off to
make the full range of adjustments accessible.
•
While receiving a 3D signal,
The FORMATkey is disabled.
The INTERNETkey is disabled.
3D Safety Requirements
Checkerboard
Blurry double image
(always required for
checkerboard signals)
Press EXITto close the menu.
If the image does not appear correct (e.g., objects
appear to be moving in instead of out), open the
Picture > 3D Mode menu. Highlight the Reverse
setting for the current control type and press ENTER
to add a check.
3D Video Settings
3D signals and 3D settings affect some TV functions.
Switch to a non-3D source to regain full TV operation.
If Source Format is set to Automatic or one of the
named 3D formats OR Source Format is set to Off and
•
&
Use Off to prevent IR interference when using an external
emitter.
Use Off for DLP Link if you are
not using DLP Link glasses.
and press
Side by Side
Two images, screen
split vertically
4,
°
Switch the TV to the 3D video device. Press INPUT
then highlight the icon for the 3D video device. Press
ENTER.
3_
The Off settings disable output
from the selected emitter.
°
°
3D Glasses are NOT designed as sunglasses or safety
glasses and do not provide protection. 3D glasses
should be worn only when viewing 3D material.
Do not wear the wireless glasses in any situations
that require unimpaired visual perception.
Children under the age of 5 should not view 3D
programming.
Under normal conditions, 3D viewing is safe for your movies
or games. Some people may experience discomfort, however.
To minimize the potential for experiencing visual problems or
any adverse symptoms:
•
°
When finished watching 3D video:
Read and follow any and all safety warnings that accompany your 3D glasses or 3D source devices.
Maintain a distance of no less than 2 to 2.5 times the
screen height measurement away from the display.
Viewing from too short a distance can strain your eyes.
Take regular breaks, at least 5 minutes after every hour of
3D viewing.
•
If your 3D video device is HDMI 1.4a compliant,
keep the setting on Automatic.
•
°
If you manually selected a source format in the
Picture > 3D menu, open the menu again and
select Automatic or Off.
If you experience any of the following symptoms, discontinue
3D viewing until the symptoms go away:
•
•
nausea, dizziness, or queasiness,
headache, or eyestrain,
For assistance
call 1(800) 332-2119
22
3.
TV Features
3D Video, continued
Wireless Audio Playback (840 Series)
•
blurry vision,
•
double vision that lasts longer than a few seconds,
Do not engage in any potentially hazardous activity (for
example, driving a vehicle) until your symptoms have completely gone away. If symptoms persist, discontinue use and
do not resume 3D viewing without discussing your symptoms
with a physician.
Do not use the glasses where loss of balance or limiting your
field of vision may be dangerous to you.
Do not use near staircases, ledges or balconies. You may
risk falling during or after use.
Epilepsy
WARNING! IF YOU OR ANY MEMBER OF YOUR FAMILY
HAS A HISTORY OF EPILEPSY,CONSULT A PHYSICIAN
BEFORE USING 3D VIDEO OR GAME PRODUCTS.
A small percentage of the population may experience epileptic seizures when viewing certain types of TV images or video
games that contain flashing patterns of light.
The following people should consult a physician before
viewing 3D Games or Video:
•
Anyone with a history of epilepsy, or who has a family
member with a history of epilepsy
•
Anyone who has ever experienced epileptic seizures or
sensory disturbances triggered by flashing light effects.
The TV's built-in speaker array can play audio from a
handheld device using Bluetooth® A2DP (stereo audio)
wireless technology.
Pairing
Device
the TV with an Audio Playback
1,
Turn on the wireless device you wish to use for
playback.
2,
Press [/NPUTIto display the Input Selection
3,
Highlight the Bluetooth
4°
Pair your device with the TV and then connect. Some
devices pair and connect automatically, while others
require you to enter the TV pass code displayed.
5°
Use keys on the TV's remote control to control playback. Not all keys work for all devices.
Resetting
Bluetooth
menu.
icon and press _.
Pairing
or Connection
Perform this reset if the audio device does not connect
properly to the TV.
1,
If the audio device has been previously paired with
the TV, delete the TV from the device's paired list.
Go to the TV's Inputs > Name menu and highlight
the B/uetooth icon. Press _to
select Off.
WARNING! SOME LIGHT PATTERNS MAY INDUCE
SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF
EPILEPSY. DISCONTINUE 3D VIEWING IF YOU EXPERIENCE ANY OF THE FOLLOWING SYMPTOMS:
3,
Press EXIT.
4,
Go to the Inputs > Name menu and highlight the
B/uetooth icon. Press _
to select On.
•
•
•
•
•
5°
Press _.
Involuntary movements, eye or muscle twitching
Muscle cramps
Nausea, dizziness, or queasiness
Convulsions
Disorientation, confusion, or loss of awareness of your
surroundings
Notice Concerning
Format
Compatibility
The Mitsubishi TVs will support the mandatory HDMI
1.4a 3D signals intended for the United States. Specifically, the TVs will support the 3D signals known as
Frame Packing 1080p/24Hz and 720p/60Hz (primarily from Blu-ray players and gaming consoles), Sideby-Side in 1080i/60Hz, 1080p/24Hz/30Hz/60Hz
and
720p/60Hz, Top/Bottom in 1080p/24Hz and 720p/60Hz,
and Checkerboard 1080p/60Hz. However, there may be
some 3D sources that are not compatible with the TVs.
In all cases: (1) 3D sources must connect to the TVs
using the HDMI inputs or via StreamTV TM Internet Media;
and (2) Active Shutter 3D glasses that match the TV's
internal synchronization emitter, or Active Shutter 3D
glasses with their own external matching synchronization emitter connected to the rear of the TV or DLP Link
Active Shutter 3D glasses are required in order to view
3D content.
For assistance
call 1(800) 332-2119
Tips for Wireless
Playback
•
Selecting the Bluetooth icon at a later time will
connect the TV again to the paired device.
•
If the paired device is not available, the TV will
accept pairing from a different device.
•
Once connection is lost, the TV will power off after
five minutes without receiving a signal.
•
To clear a paired device, turn off the Bluetooth icon
(Inputs > Name menu) or pair the TV with a different device.
•
To remove the Bluetooth icon from the Input
Selection menu, turn off the icon in the Inputs >
Name menu.
3.
TV Features
23
Sound Projector (840 Series)
Sound Projector
Technology
The TV's built-in speaker array can be adjusted to
reflect sound off the room walls to create a surround
sound effect. Setup can be performed either manually
or automatically.
•
•
To create the surround sound effect, the room walls
must reflect sound and not be covered with soundabsorbent material.
Connecting the TV
To hear digital surround sound, the TV must be connected to a digital surround sound source. The TV can
receive digital surround sound from:
•
•
Any HDMI jack
The ANT input (from some digital broadcasts)
Other stereo connections
surround sound.
will provide Dolby Pro Logic
Repeat the setup procedure if you reconfigure the
room's walls or furnishings.
Before You Begin
Positioning the TV
•
Center the seating area in front of the TV and at
least six feet away from it.
•
Arrangements
•
If the room is an odd shape, locate the TV to take
best advantage of wall reflections.
•
Avoid locations that may distort sound reflections.
that give good results:
For assistance
call 1(800) 332-2119
24
3.
TV Features
Sound Projector, continued
Auto Setup
Basic Manual
Auto setup uses a calibration microphone to optimize
Sound Projector performance for most room conditions.
Initial Preparation
1,
Note:
1°
Setup
If you have already performed Auto setup, do
not make manual adjustments. Doing so will
erase all settings created during Auto setup.
Press _
and go to Sound > SoundPro.
Position and connect the TV as described under
"Before You Begin" on the previous page.
2,
Power on the TV and external subwoofer, if any.
3°
Plug the microphone cable into the TV's INPUT 1 left
(white) audio jack.
°
Enter the room dimensions and layout information
requested in the screen. To change measurements, press • • or enter numbers on the remote
control's keypad.
°
Press _
Connect microphone to the
right (red) audio input jack.
4°
Place the microphone as described in the guidelines on the previous page.
Start Auto Setup
5°
Press _
and go to Sound > AutoSP.
4°
to exit and save settings.
Play some sample audio to check sound quality.
If further adjustment is needed, use the Custom
menu as described next.
Custom
Menu
Use the Custom menu after defining the room layout.
For a room with large areas of curtains that might affect
sound reflection, do the following:
a.
b.
6,
Highlight START and press _.
Z
Quietly exit the room right away. The calibration
sequence will start in a few seconds and may be
loud. It is important to leave the room as your presence will interfere with the calibration process.
o
Wait for completion
to the room.
of setup before
returning
9° Play some sample audio material to check the
sound quality.
Note:
Do not perform manual adjustments after running Auto setup, as this will erase all settings
defined during Auto setup.
10° Store the microphone out of direct sunlight and
away from heat.
For assistance
call 1(800) 332-2119
c.
d.
Open the curtains fully to improve sound reflection.
Set angles by performing the procedure in
"Adjusting Beam Angles."
CIosethe curtains.
Set levels by performing the procedure in
"Adjusting Levels."
3.
TV Features
25
Sound Projector, continued
1,
From the Sound > SoundPro menu go to the
CUSTOM menu.
Position yourself in your usual viewing location.
Remain in this position, looking at the TV, while
making the following adjustments.
3_
Adjusting Beam Angles
a.
Adjust Center Beam Angle until sound is
about equal in both ears.
b.
Adjust Left Beam Angle to maximize sound
heard from the front left side.
c.
Adjust Right Beam Angle to maximize sound
heard from the front right side.
d.
Adjust Left Surround Beam Angle to where
the sound seems to come from the left rear
side. If this cannot be achieved, make the
setting the same as that for Left Beam Angle.
e=
4_
Adjust Right Surround Beam Angle to where
the sound seems to come from the right rear
side. If this cannot be achieved, make the
setting the same as that for Right Beam Angle.
Adjusting Levels
a.
Adjust Center Level to the mid level.
b.
Adjust the following levels one at a time so that
each one sounds about the same as the center
level:
Left Level
Right Level
Left Surround
Right Surround
5_
Level
Level
c.
Check all sound levels by quickly switching
between them using • V.
d.
Readjust individual levels in small increments
and recheck as above until all sound levels
seem about the same.
Adjusting an External Subwoofer
Note:
Set Sound > Global > Subwoofer to On to
make this adjustment available.
a.
Play sample video or music containing lowfrequency bass sound.
b.
Press [A-U-_O-}.Use • • to display the Subwoofer option.
c.
Press • • to adjust the subwoofer volume.
For assistance
call 1(800) 332-2119
26
Appendices
Appendix A: Auto Input Sensing
About Auto Input Sensing
This TV's Easy Connect TM Auto Input Sensing feature
detects the following connections automatically:
•
•
Analog video jacks
HDMI inputs (when powered on)
Tips on Auto Sensing
•
Choose a different name for each input.
•
The antenna input (ANT) and Bluetooth® are
never auto-detected.
You can remove the unused
icons from the Input Selection menu in the
Inputs > Name menu.
•
Change the device type displayed in the Input
Selection menu by using the Inputs > Name
menu.
•
Some HDMI devices can automatically tell the TV
what name to use in the Input Selection menu
and you will be unable to change the name.
The TV is unable to detect a new connection if the
Auto Input Sensing for Most Devices
When you first connect a device, the TV will:
a.
b.
c.
Detect the connected device and automatically switch to it.
Prompt you to identify the device type.
Repeat these steps for other newly detected
devices.
When You First Connect a Device
•
current input is Bluetooth® or internet.
a different input before connecting.
Switch to
•
Most Device Types. Select the device type from
the on-screen list. The device type you select here
will appear as an icon in the Input Selection menu.
Reactivating
•
A/V Receiver. For an HDMI-equipped A/V
receiver, select AVR from the list of device types if
the A/V receiver is not recognized automatically.
After you disconnect an HDMI device, Auto Input
Sensing is temporarily disabled and the disconnected
device still appears in the Input Selection menu.
HDMI CEC Devices Compatible with the
TV's HDMI Control Feature. Compatible
CEC-enabled HDMI devices are often recognized
automatically by the TV. HDMI Control may allow
you to control some functions of a CEC-enabled
device. See the supplemental Owner's Guide at
www.mitsubishi-tv.com.
Perform these steps:
1,
Auto Input Sensing for an HDMI Input
Power off the device.
Disconnect the HDMI cable.
3,
Press MENUon the TV remote control to enter the
TV main menu.
4,
Go to Inputs > Name.
Highlight the HDMI input name and press ENTERto
select Delete.
&
New Device Found screen for a device with HDMI
control enabled. Select On if you want to enable the
TV's HDMI control of the device. In some cases, as
in the example, you will also be prompted to select a
device name.
Inputs > Name menu with Delete selected for
HDMI-3.
Z
For assistance
call 1(800) 332-2119
Press EXITto clear the menus.
Connect the new device and the New Device
Found screen will display.
Appendices
Appendix B: Lamp-Cartridge
27
Replacement
CAUTION:
If the television is on, press POWER to turn it off. Unplug the television and
allow it to cool for at least one hour before attempting to replace the lamp cartridge.
Lamp
A
A
/_\
The light source for this television is a
lamp, which is part of a lamp cartridge
assembly. The life of the lamp can
vary, based on the lamp itself, the air
temperature around the TV while it is
operating, the selected lamp mode, and
your viewing patterns. Warmer air or
poor ventilation shorten the lamp life, as
does setting Lamp Energy to Bright
and turning the television on and off
frequently.
BURN DANGER!
HOT SURFACES
INSIDE!
Touch lamp cartridge handle only. Do not touch lamp or lamp cartridge housing. Keep lamp cartridge horizontal during removal. Do
not tilt as glass may come out and cause injury. Replace lamp cartridge only with the same part number 915B455011.
WARNING
Mitsubishi warrants the lamp for one (1) year from the date of original
TV purchase at retail.
The lamp cartridge assembly is designed to be replaced by the TV
owner. The cost of labor for a service technician to replace the lamp
is not covered by the warranty.
Ordering
a New Lamp
To Receive
•
Visit
•
Call
and
a Replacement Lamp Cartridge Assembly Under Warranty
our website at www.mitsuparts.com.
(800) 553-7278. Please have model number, serial number,
TV purchase date available.
THE ACCESS PANEL IS
PROVIDED WITH AN INTERLOCK
TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET
RADIATION. DO NOT DEFEAT
ITS PURPOSE OR ATTEMPT TO
SERVICE WITHOUT REMOVING
PANEL COMPLETELY.
To Purchase a Replacement Lamp Cartridge Assembly After Warranty
Visit our website at www.mitsuparts.com
or call (800) 553-7278. Order the following:
Lamp Part Number
Lamp-Substitution
915B455011
Alert
MEVSA recommends that you use only genuine Replacement Lamp Assemblies purchased directly from Mitsubishi or a
Mitsubishi Authorized Dealer or Mitsubishi Authorized Service Center. MEVSA advises that replacement lamps obtained
separately from the Lamp Cartridge and/or Lamp Assemblies obtained from unauthorized sellers may be incorrect for
your television, may not fit or perform properly and may even damage your television. MEVSA can not be responsible
for the performance, reliability or safety of any replacement lamps that are obtained from unauthorized sources.
WARNING
•
Do not remove the lamp cartridge immediately after turning off the television. You may get burned because the
lamp is very hot. Allow the television to cool for at least one hour before replacing the lamp cartridge.
•
Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire.
•
Do not touch the lamp glass element.
•
Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical
shock. If a foreign object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for service.
•
Install the lamp cartridge securely.
•
Do not touch the lamp glass elements.
= MERCURY
It may be very hot and break, causing injuries or burns.
Failure to do so may cause a fire.
Oils from your fingers may cause premature lamp failure.
THE LAMP INSIDE THIS PRODUCT CONTAINS MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance at www.eiae.org
For assistance
call 1(800) 332-2119
28
Appendices
Appendix B: Lamp-Cartridge
Replacement
Replacement,
continued
Procedure
Removing the Old Lamp Cartrldge
1,
Turn off TV power and unplug the TV. Allow the
lamp to cool for at least one hour before proceeding.
After the lamp has cooled, remove the cover of the
lamp compartment, located on the back of the TV.
Refer to figures 1 and 2. Use a #2 (medium) Phillips
screwdriver to loosen the screws securing the
cover.
Keep the screws and cover for re-installation
3,
With a medium Phillips screwdriver, loosen the
screw securing the lamp cartridge until it disengage
from the mating threads. This is a captive screw
and cannot be separated from the lamp cartridge.
4,
Fully open the bag supplied with the replacement
lamp and set the opened bag aside.
Gently grasp the handle of the lamp cartridge and
pull the old cartridge straight out. See figure 3.
Figure 2
lJ
-......
I
Step 3
Figure
Use only replacement
915B455011.
lamp
part number
CAUTION: Do not tilt or rotate the cartridge, as
small glass fragments may fall out.
G,
Without tilting or putting down the lamp cartridge,
insert it into the opened bag. Close the bag while
being careful not to let any glass particles fall out.
Installing the New Lam# Cartrldge
1,
Do not touch the glass parts of the new lamp cartridge. Insert the new cartridge into the TV in the
same orientation as the old cartridge. Push on the
cartridge housing until it is fully seated.
Gently tighten the lamp screw with the screwdriver.
AVOID OVERTIGHTENING!
3,
Replace the plastic cover and retaining screws.
4,
WASH YOUR HANDS THOROUGHLY, AS THIS
LAMP CONTAINS MERCURY.
For assistance
call 1(800) 332-2119
Disposal of the Old Lamp Cartridge
Contact your local authorities or the Electronic Industries
Alliance at www.eiae.org for lamp-disposal or recycling instructions. Do not dispose of the old lamp with
common trash.
Appendices
29
Appendix C: Troubleshooting
TV Reset Comparison
Guide
You can resolve many common TV problems using the
reset functions described in the following table.
IMPORTANT
Before you change sound or picture settings: If
picture or sound settings seem wrong for a broadcast
channel (a channel from the ANT input, a cable box, or
satellite receiver), first check other channels from the
same input before changing settings. If most other
Format
If the picture shape
seems incorrect, use
the FORMATkey to
change the picture
shape.
840 Series.
PerfectColorTM/
PerfecTint TM
Reset
(for the single
current input)
When the color
intensities seem out
of balance, use the
PerfectColor/PerfecTint
reset to reset the color
balances to the original
factory settings.
Both PerfectColor and
PerfecTint are reset at
the same time.
A/V Memory
Reset
(for the single
current input)
When audio and/or video
A/V Reset
(for all inputs)
Channel
Memorization
Press FORMATto cycle through the
picture shapes available for the
signal.
,
While viewing the input to reset,
press MENUand go to Picture >
Perfect.
2.
Press ENTERto display the
PerfectColor adjustment screen.
3.
Press CANCELto reset the colors.
,
While viewing the input to reset,
press MENUand go to Picture >
Reset.
settings for a single input
seem incorrect, use A/V
Memory Reset to return
2.
the input to the original
3.
factory settings.
Press • to highlight Reset.
Press ENTERagain to reset.
The last-used format for the signal
type will be recalled on the input.
Note: Also check the aspect
ratio feature on your cable box or
satellite receiver as this may be
altering the picture.
All PerfectColor/PerfecTint
sliders are reset to the original
center position. The PefectColor/
PerfecTint settings for other
inputs remain unchanged.
Most Audio and Video settings
for the individual input are reset
except for the global settings
for audio Balance, Listen To,
Language, and Advanced.
To reset audio and
video adjustments for
all inputs to the original
factory settings.
While viewing the TV, press the
control-panel buttons INPUTand
VOLUMEDOWNat the same time for at
least two seconds.
Most Audio and Video settings
are returned to the original
factory settings, including global
settings not affected by Picture
> Reset. Settings under Picture
> Advanced are unaffected.
To erase and re-memorize channels on the
ANT input.
1.
All previously memorized channels for the antenna input are
erased and a new set of memorized channels is created. All
channel information in the
FAV menu, ChannelView, and
Channel Lock is deleted. To add
or delete individual channels,
use the Setup > Channel > Edit
menu.
2.
3.
4.
5.
Lock Menu
Pass Code
channels from the same input seem correct, there is
likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix
problems on individual channels also affect all other
channels on the same input.
To change your Lock
menu pass code
Press MENUand go to Setup >
Channel.
Highlight the reception mode,
e.g. Ant Air, and press ENTER.
Highlight All Channels and
press ENTER.
Highlight Scan.
Press ENTERto start channel
memorization.
Press the 9 and LASTkeys simultaneously to temporarily unlock the TV. See
the supplemental Owner's Guide at www.mitsubishi-tv.com
for more.
For assistance
call 1(800) 332-2119
30
Appendix
Appendices
C: Troubleshooting,
continued
Control-Panel
Lock Release
To re-enable the
control-panel buttons
after activation of the
Control-Panel Lock
Press and hold the INPUTbutton on
the control panel for ten seconds. If
the TV is powered off, you can now
cress the POWERbutton to turn it on.
Allows the control panel to be
unlocked if the remote control is
misplaced.
System Reset
If the TV does not turn
on or off, does not
respond to the remote
control or controloanel buttons, or has
audio but no video.
Press and hold the POWERbutton on
The TV will turn off. The green
LED will flash quickly for about
one minute. The changes you
made most recently, before using
SYSTEMRESET,may be lost.
TV Reset
IMPORTANT:
Use this reset
only if other
troubleshooting
has been unsuccessful.
To reset all consumeraccessible settings
and all memories to
the original factory
defaults.
Use TV Reset if the TV
can respond to controls but TV behavior is
abnormal.
CAUTION:
the control panel for ten seconds.
1.
2.
3.
All owner-
oerformed setups and
adjustments will be
erased.
For assistance
call 1(800) 332-2119
While viewing the TV, press
MENUto display the TV main
menu.
With the main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
READ THE ON-SCREEN
WARNING AND INSTRUCTIONS.
•
If you do not wish to use this
reset, press EXITor MENUto
back out.
•
If you wish to continue,
press ENTERto erase all
memories and settings.
The TV will start the initialization
process and then turn off.
The front green LED will start
flashing. All memory and
settings outlined in this Owner's
Guide will need to be set again.
Appendices
Appendix
C: Troubleshooting,
31
continued
Common Picture Problems
Picture does not look like a high-definition picture.
,
Compare the picture to the TV's test picture (Picture > Picture+ menu)
to check if the source signal is supplying a lesser-quality image.
Not all signals are high-definition signals. To receive high-definition
programming from your cable or satellite provider, you must subscribe to the provider's high-definition service. Some over-the-air
broadcasts are in high-definition and can be received with a highquality antenna suited to your location.
2.
TV has sound but no picture.
•
•
•
3.
A color program appears as a black
and white image, or the colors are dim,
or the screen is black.
•
•
•
4.
Picture from an HDMI input is noisy
(poor quality).
•
•
Front-Panel
STATUS
Compare the picture to the TV's test picture (Picture > Picture+
menu) to check the source of the noise.
Upgrade a standard (unmarked) HDMI cable to a high-speed
HDMI cable.
Green O
TVis powered
Green
O
TV powered off, auto-on TV Timer is set.
Normal operation. TV can be turned on at any time.
Green
Q
TV just powered off and lamp is cooling. Sixty seconds after turning off TV, LED
will start to blink. TV can be turned back on before blinking starts or after blinking
stops, but not while the indicator is blinking. Normal operation.
on. Normal operation.
TV is too hot. The TV will display a warning message and shut off if it overheats.
•
Ambient room temperature may be too high. Turn off the TV and let the room
temperature drop.
•
Clear blocked air vents. Ensure at least a four-inch clearance on all sides of the TV.
Off
O Steady On
(D Slow Blinking
_) Fast Blinking
If using component video, check that the red, green, and blue
input cables are correctly connected to the red, green, and blue
component video jacks.
If using composite video, check that the incoming cable is connected the TV's green Y/VIDEO jack.
840 Series. The PerfectColor color balance has been incorrectly
set. Reset the PerfectColor balance.
Light
Key
O
Press MENU on the remote control. If the menu displays, then
there is a problem with the incoming signal.
Check that all video inputs are plugged in firmly to the correct
input jacks.
Press and hold the POWER button on the control panel for ten
seconds to perform System Reset.
Yellow
Lamp access door is not secure or no lamp installed.
TV will not operate until lamp access door is secured. See Appendix
Red
Lamp failure.
Red/
Yellow
TV may require
•
•
•
Replace the lamp. See Appendix
B.
B.
service.
Hold power button on front panel for 10 seconds to reset TV.
If LED continues to flash red and yellow after reset, unplug the TV from the AC
power source. Wait one minute and then plug the set back in.
If LED continues to flash red and yellow, go to www.mitsubishi-tv.com
or call
1-800-332-2119 to receive Authorized Service Center information.
You may be asked to count how many times the LED flashes each color to aid
in troubleshooting.
For assistance
call 1(800) 332-2119
32
Mitsubishi
TV Software
Mitsubishi TV Software
END-USER
LICENSE AGREEMENT
FOR EMBEDDED
SOFTWARE
IMPORTANT
- READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Electric Visual Solutions America, Inc. (MEVSA) for all software pre installed and/or provided along with this television
("Software").
By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software
and treaties.
is protected
by United States copyright
The Software is licensed, not sold.
laws and international
1.
Software
LICENSE GRANT.
MEVSA grants you a non-exclusive,
only with the Mitsubishi television model that included
2.
RIGHTS
Software
Software
Not for Resale. You may not resell or otherwise
has been pre installed.
treaty
provisions,
as well as other intellectual
property
laws
non-transferable,
limited right and license to use one copy of the
this owner's guide and owned by you.
AND LIMITATIONS.
transfer
for value the Software,
except
in conjunction
with a sale of the TV that
Prohibition on Reverse Enqineerinq, Decompilation
and Disassembly.
The Software contains trade secrets or other proprietary
material
in its human perceivable form and to protect them, you may not reverse engineer, decompile,
or disassemble,
or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction
is expressly prohibited by applicable law.
Separation of Components.
than one TV.
No Rental.
The Software
is licensed
as a single product.
You may not rent, lease, lend, or sublicense
Trademarks.
This License
Agreement
or indirectly
via third parties,
update
or change
parts may not be separated
for use on more
the Software.
does not grant you any rights to any trademarks
U_odates. MEVSA may elect, but shall be under no obligation,
enhancements,
or modifications
to the Software.
Depending
directly,
Its component
of MEVSA.
to provide you with customer support and/or software upgrades,
on the Mitsubishi TV model and internet access capability, MEVSA may
such Software,
in whole or in part, at any time and without
notice
to you.
3.
VIOLATIONS.
You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MEVSA of attorneys' fees in connection
with
any violation of this License. You further understand
that you may be held legally responsible for any copyright
infringement or other
violation of intellectual
property rights that is caused, encouraged,
or induced by your failure to abide by the terms of the License. This
license is effective until terminated,
and will terminate immediately
without notice from MEVSA or judicial resolution if you fail to comply
with any provision of this License.
4.
COPYRIGHT.
All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations,
video, audio, music, text, and "applets" incorporated
into the Software), and any accompanying
printed materials are owned
by or licensed to MEVSA. All title and intellectual property rights in and to the content which may be accessed through use of the
Software is the property of the respective content owner and may be protected
by applicable copyright or other intellectual
property laws
and treaties. This License Agreement
grants you no rights to use such content, except that you own the media on which the Software is
recorded, but MEVSA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MEVSA.
5.
EXPORT RESTRICTIONS.
MEVSA is licensing the Software for use within the United States. You agree that you will not
export or re-export the Software.
You specifically
agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed
or restricted the export of goods or services, which currently include, but are not necessarily
limited to Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software
back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development,
or production
of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating
in
U.S. export transactions
by any federal agency of the U.S. government.
You warrant and represent that neither the BXA nor any other U.S.
federal agency has suspended,
revoked, or denied your export privileges.
6.
DISCLAIMER
OF WARRANTY.
EXCEPT
AS OTHERWISE
PROVIDED
IN THIS
LICENSE
OR IN THE LIMITED
WARRANTY
APPLICABLE
TO THE TV, MEVSA MAKES NO OTHER WARRANTIES
OF ANY KIND WHATSOEVER
REGARDING
THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS
ALL WARRANTIES
OF ANY KIND WHATSOEVER,
EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE.
ALL IMPLIED WARRANTIES,
INCLUDING,
WITHOUT LIMITATION,
THE IMPLIED WARRANTIES
OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED
BY MEVSA.
IN
NO EVENT SHALL MEVSA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT,
IN TORT OR OTHERWISE,
FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL
DAMAGES
OF ANY KIND OR NATURE.
BECAUSE SOME
JURISDICTIONS
DO NOT ALLOW THE EXCLUSION
OR LIMITATION
OF IMPLIED WARRANTIES,
THE ABOVE LIMITATION
MAY
NOT APPLY TO YOU.
7.
LIMITATION
OF LIABILITY.
MEVSA SHALL NOT, UNDER ANY CIRCUMSTANCES
BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER
INDIRECT, SPECIAL, INCIDENTAL,
CONSEQUENTIAL
OR
OTHERWISE,
INCLUDING,
BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED
FOR IN RELIANCE
ON THE CONTINUATION
OF THIS LICENSE.
YOU AGREE THAT NEITHER MEVSA'S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL
ESSENTIAL
PURPOSE OF THIS LICENSE.
BECAUSE SOME JURISDICTIONS
DO NOT ALLOW
OF LIABILITY
FOR CONSEQUENTIAL
OR INCIDENTAL
DAMAGES,
THE ABOVE
LIMITATIONS
liability to you for direct damages
for any cause whatsoever
and regardless
of the form
paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL.
For assistance
This License Agreement
will be governed
call 1(800) 332-2119
CONSTITUTE
A FAILURE OF THE
THE EXCLUSION
OR LIMITATION
MAY NOT APPLY TO YOU.
of the action,
by the laws of the State of California.
will
be limited
MEVSA's
to the money
Mitsubishi
TV Software
33
GNU General Public License
Version
Copyright
2, June 1991
(C) 1989, 1991
Free Software
Foundation,
675 Mass Ave, Cambridge,
Everyone
is permitted
to copy and distribute
verbatim
copies
Inc.
MA 02139, USA
of this license
document,
but changing
it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and changeit. By contrast, the GNU General Public Licenseis intended to guarantee your freedom to share and
changefree software--to make surethe software is free for all its users. This General Public Licenseapplies to most of the Free Software Foundation's software and to any other program whose authors
commit to using it. (Someother Free Software Foundationsoftware is covered by the GNU Library GeneralPublic Licenseinstead.) Youcan apply it to your programs, too.
When we speak of free software we are referring to freedom, not price. Our General Public Licensesare designed to makesure that you have the freedom to distribute copies of free software (and charge for
th s serv ce f you w sh, that you rece ve source code or canget t f you want it, that you can changethe software or use pieces of it in new free programs; and that you know you can do thesethings.
To protect your rights, we need to makerestrictions that forbid anyone to deny you these rights or to ask you to surrenderthe rights. Theserestrictions translateto certain responsibilities for you if you
distribute copies of the software, or if you modify it.
Forexample if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. Youmust makesurethat they, too, receive or can get the source
code. And you must show them theseterms so they know the r r ghts.
We protect your rights with two steps: (1)copyright the software, and (2) offer you this licensewhich gives you legal permissionto copy, distribute and/or modify the software.
Also for each author's protection and ours we want to makecertain that everyoneunderstands that there is no warranty for this free software. If the software is modified by someone else and passed on, we
want ts rec p ents to know that what they have s not the or g na, so that anyprob eros ntroduced by others w not ref ect on the or g na authors reputat ons.
Finally,anyfree program is threatenedconstantly by software patents. We wish to avoid the dangerthat redistributors of a free program will individually obtain patent licenses, in effect making the program
proprietary. Toprevent this, we have made it clear {hatany patent must be licensed for everyone'sfree use or not licensedat all.
The precise terms and conditions for copying, distribution and modificationfollow.
GNU GENERALPUBLIC LICENSE
TERMS AND CONDITIONS FORCOPYING DISTRIBUTIONAND MODIFICATION
O. This Licenseapplies to any program or otherwork which contains a notice I_lacedby the copyright hol_lersaying it may be distributed under the terms of this General Public License. The "Program",
below, refers to anysuch nrogram or work, and a "work based on the Program" means eitherthe Pronram or any derivativework under copyright law:that is to sav a work containing the Programor a I_ortion
of it, either verbatim or wi{'l_modifications and/or translated into another language. (Hereinafter,translation is included without limitation in{l_sterm "modification .I Eachlicensee is addressed as "you".
Activities otherthan copying distribution and modification are not covered by this License; they areoutside its scope. The act of running the Program is not restricted, and the output from the Program is
covered on y f ts contents const tute a work based on the Program ndependentof hayng been made by runn ng the Program. Whetherthat sfrue depends on what the Programdoes.
1. You may copy and distribute verbatim copies of the Program'ssource code as you receive it, in anymedium, provided that you conspicuouslyand appropriately publish on each copy anappropriate
copyright notice and disclaimer of warranty keep intact all'the notices that refer to this Licenseand to the absence of any warranty and give anyother recipients of the Program a copy of this Licensealong
w th the Program.
Youmay charge a fee for the physicalact of transferring a copy, and you may at your option offer warranty protection in exchangefor a fee.
2. You may modify your copy or copies of the Programor any portion of it thus forming a work based on the Program and copy and distribute such modifications or work under the terms of Section 1 above,
provided that you also meetall of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the dateof anychange.
b) You must cause any work that you distribute or publish,that in wholeor in part contains or is derived from the Program or anypart thereof, to be licensed as a whole at no charge to all third parties
under the terms of this License.
c) If the modified program normally reads commands interactivelywhen run you must cause it when started running for such interactive use in the most ordinary way to print or display an
announcementinclud]ng anappropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that usersmay redistributethe program under these
conditions, and telling tl_euserhow to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such anannouncement your work based onthe Program
s not required to pr nt an announcement.
These requirementsapply to the modified work as a whole. If identifiable sections of that work are not derived from the Program and can be reasonably considered independent and separate works in themselves then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on
the Program,the d str but on of the who e must be on the terms of th s L cense, whose permss ons for other censees extend to the ent re who e, and thus to each and every part regard ess of who wrote t.
Thus, it is not the intent of this section to claim rightsor contest your rights to work written entirely by you; rather, the intent is to exercisethe right to control the distribution of derivativeor collective works
based on the Program.
In addition mereaggregation of another work not based on the Programwith the Program (or with a work based on the Program)on a volume of a storage or distribution medium does not bring the other
work under the scope of th s L cense.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readablesource code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange;or,
b) Accompany it with a written offer, valid for at least three years,to give anythird party, for a charge no more thanyour cost of phy.sicallyperformingsource distribution, a complete machine-readable
copy of the corresponding source code to be distributed under the terms of Sections "[and 2 above on a medium customarily used for software interchange or,
c) Accompany it with the informationy.oureceived as to the offer to distribute corres£ondingsource code. (This alternativeis allowed only for noncommercialdistribution and only if you receivedthe
program in object code or executable form with such an offer, inaccord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executablework complete source code means all the source code for all modules it contains plus any
associatedinterface definition files plus the scripts used to control compilation and installation of the executable. However as a special exception the source code distributed need not include anythingthat
is normally distributed (in either source or binary form) with the major components (compiler kernel and so on)of the operating system on which the executableruns unless that component itself accompan es the executab e.
If distribution of executable or object code is made by offering accessto copy from a designated place then offering equivalentaccess to copy the source code from the same place counts as distribution of
the source code, even though third parties are not compe ed to copy the source a ong w th the ob ect code.
4. You may not copy modify sublicense or distribute the Programexcept as expressly provided under this License. Any attempt otherwiseto copy modify sublicense or distribute the Program is void and
will automatically terminate your rights under this License. However parties who have receivedcopies or rights from you under this License will not have their licensesterminated so long as such parties
reman n fu comp ance.
5. You arenot required to accept this License, sincejou havenot signed it. However,nothing else grants you permissionto modifXor distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. i nerefore,by modifying or distributing the Program (or anywork based on the _'rogram),you indicateyour acceptance of this Licenseto do so, and all its
terms and conditions for copying, distributing or modifying the Programor works based on it.
6. Eachtime you redistribute the Program (or anywork based on the Program) the recipientautomatically receives a license from the original licensor to copy, distribute or modify the Program subject to
these terms and cond tons. You may not repose any further restr ct ons on the rec p ents exercse of the r ghts granted here n. Youare not respons b e for enforc ng comp ance by th rd part es to th s
License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues),conditions areimposed on you (whether by court order, agreementor
otherwise)that contradict the conditions of this License,they do not excuseyou from the conditions of this License. If you cannot distribute so as to satisfy simultaneouslyyour obligations under this License
and anyother pertinent obligations thenas a consequence you may not distribute the Program at all. For example, if a patent licensewould not permit royalty-free redistribution of t]_eProgram by all those
who rece ve cop es d rect y or nd rect y through you, then the on y way you cou d sat sfy both t and th s L censewou d beto refra n ent re y from d str butlon of the Program.
If any portion of this section is held invalid or unenforceableunder any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not thepurpose of this section to induceyou to infringeany patents or other property right claims or to contest validity of anysuch claims; this section has the sole purposeof protecting the integrity of
the free software distribution system which is implemented by public license practices. Manypeople have made generouscontributions to the wide range of software distributed through that system in reliance on consstent app cat on of that system; t s up to the author/donor to dec de f heor she s w ng to d str bu_esoftware through any othersystem and a censee cannot repose that cho ce.
This section is intended to makethoroughly clear what is believed to bea consequenceof the rest of this License.
8. If the distribution and/or useof the Programis restricted in certain countries either by patents or by copyrighted interfaces,the original copyright holder who places the Program under this License may.
add an explicit geographical distribution limitationexcluding thosecountries so that distribution is permitted only in or among countries not thus excluded. In such case this License incorporates the limitation as if written in t]_ebody of this License.
9. The FreeSoftware Foundation may publish revised and/or new versions of the General Public Licensefrom time to time. Such new versions will be similar in spirit to the presentversion, but may differ in
detail to address new problems or concerns.
Eachversion is given a distinguishing version number. If the Programspecifies a version number of this License which applies to it and "any later version",you have the option of following the terms and conditions either of_hat version or of any laterversion publishedby the FreeSoftware Foundation. If the Program does not specify a version number of this License, you may choose any version ever published
by the Free Software Foundation.
If you are interested in obtaining open source code for this product, please contact Mitsubishi at
1 (800) 332-2119. A nominal handling and mailing charge may apply.
For assistance
call 1(800) 332-2119
34
Mitsubishi
TV Software
10. Ifyou wishtoincorporatepartsoftheProgramintootherfree
programs whose distribution conditions aredifferent, write to the author to ask for permission. For software which is copyrighted bythe
FreeSoftware Foundation write to the Free Software Foundation;we sometimes makeexceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivativesof our
free software and of promot ng the shar ng and reuse of software genera y,
NOWARRANTY
11, BECAUSETHEPROGRAMIS LICENSEDFREEOF CHARGETHERE ISNO WARRANTYFORTHEPROGRAM TO THE EXTENTPERMITTEDBY APPLICABLELAW. EXCEPTWHEN OTHERWISE
STATEDIN WRITINGTHE COPYRIGHTHOLDERSAND/OR OTHI_RPARTIESPROVIDETHE PROGRAM"AS IS" WITHOUTWARRANTYOF ANY KIND EITHEREXPRESSEDOR IMPLIED INCLUDING BUT
NOTLIMITEDTO THE IMPLIEDWARRANTIESOF MERCHANTABILITYANDFITNESSFORA PARTICULARPURPOSE.THE ENTIRERISK ASTO THEQUALITYANDPERFORMANCEO'FTHE PROGRAM
S W TH YOU. SHOULDTHEPROGRAMPROVEDEFECTVE, YOUASSUMETHE COSTOF ALLNECESSARYSERVC NG,REPA R ORCORRECTON.
12. IN NO EVENTUNLESSREQUIREDBYAPPLICABLELAW ORAGREEDTO IN WRITINGWILL ANY COPYRIGHTHOLDER,OR ANY OTHERPARTYWHO MAYMODIFY AND/ORREDISTRIBUTETHE
PROGRAMAS PERMITTEDABOVE, BE LIABLETO YOU FORDAMAGES,INCLUDINGANY GENERAL SPECIAL INCIDENTALOR CONSEQUENTIALDAMAGESARISINGOUTOF THE USEOR INABILITY
TO USETHE PROGRAM(INCLUDINGBUT NOTLIMITEDTO LOSS OF DATAOR DATABEINGRENDEREDINACCURATEOR LOSSESSUSTAINEDBY YOUOR THIRDPARTIESOR A FAILUREOF THE
PROGRAMTO OPERATEWITH ANY OTHERPROGRAMS),EVEN IF SUCHHOLDEROR OTHERPARTYHAS BEENADVISEDOF THE POSSIBILITYOF SUCH DAMAGES.
GNU GENERAL PUBLIC LICENSE
Version3,29 June2007
Copyright@2007FreeSoftwareFoundation{nc.<http://fsf.org/>
Everyones permtted to copyand d strbuteverbatm copes ot th s censedocument,but changng t s not a owed,
Preamble
TheGNUGeneralPublicLicenseis a free,copyleftlicensefor softwareandotherkindsof works.
Thelicensesfor mostsoftwareandotherpracticalworksaredesignedto takeawayyourfreedomto shareandchangethe works,By contrast,the GNUGeneralPublicLicenseis intendedto guaranteeyourfreedomto share
andchangeallversionsof a program-4omakesureit remainsfree softwarefor all _tsusers,We the FreeSoftwareFoundationusefhe GNUGeneralPublicLicensefor mostof oursoftware if@pliesalsoto anyotherwork
released(niswayby its authors._foucanapply it to yourprograms,too.
Whenwe speakof free software,wearerefernngto freedom,not price.OurGeneralPublicLicensesaredesignedto makesurethatyouhavethe freedomto distributecopiesof freesoftware(andchargefor themif youwish),
thatyoureceivesourcecodeor canget it if youwant it,thatyou canchangethe softwareor usepiecesof it in newfree programs,and thatyouknowyoucando thesethings.
Toprotectyour rightswe needto preventofhersfromdenyingyouthesenghtsor askingyouto surrenderthe rights.Thereforeyou havecertainresponsibilities
if youdistributecopiesof the softwareor if youmodifyit: responsibilitiesto respectthe freedomof others.
Forexample,if youdistributecopiesof sucha program,whethergratisor for a fee,youmust passonto the recipientsthe samefreedomsthat youreceived.Youmustmakesurethatthey,too,receiveor canget the source
code.Andyoumustshowthem thesetermsso theyknowtheirrights.
Developers
that usethe GNUGPLprotectyour rightswithtwo steps:(1)assertcopyrightonthe software,and(2)offeryouthis Licensegivingyoulegalpermissionto copy,distributeand/ormodifyit.
Forthe developers'andauthors'protection,the GPLclearlyexplainsthat thereis nowarrantyfor this freesoftware.For bothusers'and authors'sake,the GPLrequiresthat modifiedversionsbemarkedas changed,so that
theirproblemswill not beattributederroneouslyto authorsof previousversions.
Somedevicesaredesignedto denyusersaccessto installor runmodifiedversionsofthe softwareinsidethem,althoughthe manufacturer
cando so,This is fundamentally
incompatiblewiththe aimof protectingusers'freedorato changethe software.The systematicpatternof suchabuseoccursinthe areaof productsfor individualsto use,which is preciselywhereit is most unacceptable.
Therefore,we havedesignedths versionof the GPLto
prohibitthe practicefor thoseproducts.If suchproblemsarisesubstantiallyin otherdomains,westandreadyto extendthis prowsionto thosedomainsinfuture versionsofthe GPL,as neededto protectthe freedomof users.
Finally,everyprogramis threatenedconstantlyby softwarepatents.Statesshouldnot allowpatentsto restrictdevelopmentand useof softwareon general-purpose
computers,but inthosethatdo, we wishto avoidthe special
dangerthat patentsappliedto a free programcouldmakeit effectivelyproprietary.Topreventthis the GPLassuresthat patentscannotbeusedto renderthe programnomfree,
Theprecse termsand condtons for copyrig, d strbut onand roodf cat onfo ow.
TERMSAND CONDITIONS
O,Definitions,
'ThisLicense"refersto version3 of the GNUGeneralPublicLicense.
'Copyright"alsomeanscopyright-likelawsthat applyto otherkindsof works suchas semiconductor
masks.
'TheProgram"refersto anycopyrightableworklicensedunderthis License.Eachlicenseeis addressedas "you"."Licensees"and "recipients"may beindividualsor organizations.
To"modify"a workmeansto copy:fromor adaptall or part of the workina fashionrequiringcopyrightpermissionotherthanthe makingof anexactcopy.The resultingworkis calleda "modifiedversion"of theearlierworkor a
work basedon the ear er worL
A "coveredwork"meanseitherthe unmodifiedProgramor a workbasedon the Program.
To"propagate"a workmeansto doanythingwithit that withoutpermissionwouldmakeyoudirectlyor secondarilyliablefor infringementunderapplicablecopyrightlaw exceptexecutingit ona computeror modifyinga
privatecopy.Propagationincludescopying,distribution(withor withoutmodification),makingavailableto the public,andin somecountriesotheractivitiesas well.
To"convey"awork meansanykindof 15ropagation
that enablesotherpartiesto makeor receivecopies.Mereinteractionwitha userthrougha computernetwork,with notransferof a copy,is not conveying.
Aninteractiveuserinterfaced@lays "AppropriateLegalNotices"to the extentthat it includesa convenientand prominentlyvisiblefeaturethat (1)displaysanappropriatecopyrightnotice,and (2)tellsthe userthatthereis no
warrantyfor the work(exceptto the extentthatwarrantiesareprovided)that licenseesmay conveythe workunderthis Licenseandhowto view a copyof this License.If the interfacepresentsa list of usercommandsor optons, suchas a menu,a promnenttem n the st meetsth s crter on.
1, SourceCode.
The"sourcecode" for a workmeansthe preferredform of the workfor makingmodificationsto it. "Objectcode" meansanynon-source
form of a work.
A "StandardInterface"meansaninterface
thateitheris an officialstandarddefinedby a recognizedstandardsbody,or, inthe caseof interfacesspecifiedfor a particularprogramminglanguage,onethat is widelyusedamong
developersworkinqinthat language.
The"SystemLibraries"of anexecutableworkinclude
. otherthanthe workas a whol_
includedinthe normalformof
_nd(b)
seryesonlyto enableuseofthe workwiththat Ma
)[ement
it.
those
activities,
lot part ofthe work. For
specificallydesignedto
that users can
Source,
2. BasicPermissions.
Allrightsgrantedunderthis Licensearegrantedforthe termof copyrightonthe Program,and areirrevocableprovidedthe stated conditionsaremet.ThisLicenseexplicitlyaffirmsyourunlimitedpermissionto runthe unmodifledProgram.Theoutputfromrunninga coveredwork is coveredby this Licenseonlyif the output givenits content constitutesa coveredwork. ThisLicenseacknowledges
yournghtsof fair useor otherequivalentas
pn
rovidedby copyrightlaw.
Youmaymake,runandpropagatecoveredworksthatyoudo not convey,withoutconditionsso long asyourlicenseotherwiseremainsin force.Youmayconveycoveredworksto othersfor the solepurposeof havingthem
makemodificationsexclusivel#for you,or provideyouwithfacilitiesfor runningthoseworks,providedthat youcomplywiththe termsof this Licenseinconveyingallmaterialfor whichyoudo not controlcopyright.Tiiosethus
makingor runningthe coveredworksfor youmustdo so exclusivelyonyourbehalf,underyourdirectionandcontrol,ontermsthat prohibitthemfrom makinganycopiesof yourcopyrightedmaterialoutsidetheirrelationship
withyou.
Conveyingunderanyothercircumstancesis permittedsolelyunderthe conditionsstatedbelow.Sublicensing
is notallowed;section10makesit unnecessary.
3, ProtectingUsers'LegalRightsFromAnti-Circumvention
Law,
Nocoveredworkshall bedeemedpart of aneffectivetechnologicalmeasureunderanyapplicablelawfulfillingobligationsunderarticle11of the WlPOcopyrighttreatyadoptedon 20December1996,or similarlawsprohibiting
or restrictingcircumventionof suchmeasures.
Whenyou conveya coveredwork youwaiveanylegalpowerto forbid circumvention
of technologicalmeasuresto the extentsuchcircumvention
is effectedby exercisingrightsunderthis Licensewithrespectto the covered
work,andyoud sca m any ntentonto m t operaton or modf cat onof the workas a meansof enforcng, agenst theworks users,youror th rd partes ega r ghtsto forb 8 c rcumventonof technoogca measures.
4, ConveyingVerbatimCopies,
Youmayconveyverbatimcopiesof the Program'ssourcecodeas youreceiveit in anymedium providedthatyou conspicuouslyandappropriatelypublishoneachcopyan appropriatecopyrightnotice keepintactall notices
statingthatthis Licenseandanynon-permissive
termsaddedinaccordwithsectionTapplyto the code;keepintactall noticesofthe absenceof anywarranty;andgiveall recipientsa copyofthis Licensealongwiththe
D.__._(oug_a_.charg
e anypriceor nopricefor eachcopythatyou convey,andyoumay offersupportor warrantyprotectionfore fee.
5, ConveyingModifiedSourceVersions,
or the modificationsto _roduceit fromthe Programin the formof sourcecode underthe termsof section4 providedthatyoualsomeetall of theseconditions:
a reeventdate.
uirementin section4 to 'keep intacta[[notices".
7 additionalterms,to the wholeofthe
redeivedit.
If the workhas
is _oforma largerprogram inor on a volume
of
copyrightarenot usedto limitthe accessdr legalr ghtsof the comp atons usersbeyondwhatthe ndv due workspermt. nc uofthe aggregate.
6. ConveyingNon-SourceForms.
Youmayconveya coveredworkin objectcodeformunderthe termsof sections4 and5 providedthat youalsoconveythe machine-readable
Corresponding
Sourceunderthe termsof this License,inone oftheseways:
a)Oonvey
the objectcode in,or embodiedin, a physicalproduct(includinga physicaldistnbutionmedium),accompaniedby the Corresponding
Sourcefixedon a durablephysicalmediumcustomarilyusedfor softwareinter_
change.
b)Oonvey
the objectcode in,or embodiedin, a physicalproduct(includinga physicaldistributionmedium),accompaniedby a writtenoffer,validfor at leastthreeyearsandvalidfor as long asyou offerspareparts or customer
supportforthat productmodel,to giveanyonewhopossessesthe objectcodeeither(1)a copyof the Corresponding
Sourcefor allthe softwareinthe productfhat is coveredby this License,on a durablephysicalmedium
customarilyusedfor softwareinterchange,
for a pricenomorethanyourreasonablecost of physicallyperformingthis conveyingof source,or (2) accessto copytheCorrespondingSourcefroma networkserverat nocharge.
c)Conveyindividualcopiesof the objectcodewitha copyof thewrittenofferto providethe Corresponding
Source.Thisalternativeis allowedonlyoccasionallyand noncommercially
andonly ifyou receivedthe objectcode
wth suchanoffer, n accordwth subsecton 6b.
Jivalentaccessto the Corres
Sourceinthe samewa_
s. Youneed
Source,you
For assistance
call 1(800) 332-2119
Mitsubishi
TV Software
35
remainobligatedto ensurethat it is availablefor as longas neededto satisfytheserequirements.
e)Oonvey
the objectcode usingpeer-to*peer
transmission,providedyouinformotherpeerswherethe objectcode andCorresponding
Sourceof the workarebeingofferedto the generalpublicat nochargeundersubsection
6d.
Aseparableportionof the objectcode,whosesourcecodeis excludedfromthe CorrespondingSourceas a SystemLibrary,neednot beincludedinconveyingthe objectcode work.
A "UserProduct"is either(1) a "consumerproduct",which meansanytangiblepersonalproper_ywhich is normallyusedfor personal,family,or householdpurposes,or (2)anythingdesignedor soldfor incorporationintoa
dwelling.In determiningwhethera productis a consumerproduct,doubtfulcasesshallbe resolvedinfavor of coverage.Fora particularproductreceivedby a particularuser."normallyused"refersto a typicalor common
useof that classof product,regardlessof thestatusof the particularuseror of the wayin whichthe particularuseractuallyuses,or expectsor is expectedto use.the product.A productis a consumerproductregardlessof
whetherthe producthassubstantialcommercial,industrialor non-consumer
uses.unlesssuchusesrepresentthe onlysignificantmodeof useof the product.
'InstallationInformation"for a UserProductmeansanymethodsproceduresauthorizationkeys or otherinformationrequiredto installandexecutemodifiedversionsof a coveredworkin that UserProductfroma modified
versionof its Corresponding
Source.Theinformationmustsufficeto ensurethat the continuedfunctioningof the modifiedobjectcodeis in nocasepreventedor interferedwithsolelybecausemodificationhasbeen made.
if youconveyanobject codeworkunderthissectionin, or with, or specificallyfor usein, a UserProduct,andthe conveyingoccursas part of a transactioninwhich the rightof possessionanduseofthe UserProductis trans_
ferredto the recipientin perpetuityor for a fixedterm(regardlessof howthe transactionis characterized)theCorrespondingSourceconveyedunderthis sectionmustbeaccompaniedby the InstallationInformation.Butthis
requirement
doesnot apply if neitheryounoranythirdparty retainsthe abilityto installmodifiedobjectcodeonthe UserProduct(forexample,the workhasbeen installedin ROM).
Therequirement
to provideInstallationInformation
does notincludea requirement
to continueto providesupportservice,warranty,or updatesfor a workthat hasbeenmodifiedor installedby the recipient,or forthe User
Produc_inwhich it hasbeenmodifiedor installed.Accessto a networkmaybedeniedwhenthe modificationitself matenallyand adverselyaffectsthe operationof the networkor violatesthe rulesandprotocolsfor communicationacrossthe network.
Corresponding
SourceconveyedandinstallationInformationprovided inaccordwiththis sectionmustbe ina formatthat is publiclydocumented(andwith animplementation
availableto the publicin sourcecodeform),and
mustrequre nospeca passwordor keyfor unpackng,readngor copyng.
7,AdditionalTerms,
'Additionalpermissions"aretermsthat supplementthe termsof this Licenseby makingexceptionsfromoneor moreof itsconditions.Additionalpermissionsthatareapplicableto the entireProgramshallbetreatedas though
theywereincludedin this License,to the extentthatthey arevalid underapplicablelaw.if additionalpermissionsapplyonlyto part of the Program,that partmay beusedseparatelyunderthosepermissions,but the entire
Programremainsgovernedby this Licensewithoutregardto the additionalpermissions.
Whenyouconveya copyof a coveredwork,you mayat youroption removeanyadditionalpermissions
fromthat copy,or from anypartof it.(Additionalpermissions
may bewrittento requiretheirown removalin certaincases
whenyou modifythe work.)Youmayplace additionalpermissionsonmaterial,addedby youto a coveredwork,for Whichyou haveor can giveappropriatecopyrightpermission.
Notwifhstanding
anyotherprovisionof this License,formaterialyouadd to a coveredwork,youmay (ifauthorizedby the copyrightholdersofthat material)supplementthe termsof this Licensewithterms:
a)Disclaimingwarrantyor limitingliabilitydifferentlyfromthe termsof sections15and16 ofthis License;or
b)Requiring
preservationofspecifiedreasonablelegalnoticesor authorattributionsinthat materialor inthe AppropriateLegalNoticesdisplayedby workscontainingit; or
c}Prohibitingmisrepresentation
of the originof thatmaterial,or requiringthat modifiedversionsof suchmateriaIbemarkedmreasonablewaysas differentfrom the originalversionlor
d)Limitingtee usefor publicitypurposesof namesof licensorsor authorsof the material;or
e)Declining
togrant rightsundertrademarklawfor useof sometradenames,trademarks,or servicemarks;or
f)Requiringindemnification
of licensorsandauthorsof that materialby anyonewho conveysthe material(or modifiedversionsof it) withcontractualassumptionsof liabilityto the recipient,for anyliabilitythatthesecontractual
assumptionsdirectlyimposeonthoselicensorsandauthors.
Allothernompermisslve
additionaltermsareconsidered"furtherrestrictions"withinthe meaningof section10.If the Programas youreceivedit or anypart of it containsa noticestatingthat it is governedby this Licensealong
witha termthat is a furtherrestriction,youmay removethat term.If a licensedocumentcontainsa furtherrestrictionbut permitsrelicensingor conveyingunderthis License,youmayaddto a coveredworkmaterialgovernedby
the termsof that licensedocumentprovidedthat the furtherrestrictiondoesnot survivesuchrelicensingor conveying.
ifyou addtermsto a coveredworkin accordwiththis section,youmust place,inthe relevantsourcefiles, a statementof the additionaltermsthat applyto thosefiles, or a noticeindicatingwhereto findthe applicableterms.
Additionalterms,permissiveor nompermissive,
maybe statedinthe formof a separatelywrittenlicense,or statedas exceptions;the aboverequirements
applyeitherway.
8,Termination,
Youmaynot propagateor modifya coveredworkexceptasexpresslyprovidedunderthis License.Anyattemptotherwiseto propagateor modifyit is void andwill automatically
terminateyourrightsunderthis License(includ_
inganypatentlicensesgrantedunderthe third paragraphof section1I).
Howeverif youceaseall violationof this Licensethenyour licensefrom a particularcopyrightholderisreinstated(.a)provisionallyunlessanduntil thecopyrightholderexplicitlyandfinallyterminatesyourlicenseand (b)
permanently,ifthe copyrightholderrailsto notiryyouotthe violationuy somereasonablemeanspriorto 60daysatterthecessation.
Moreover.
yourlicensefroma particularcopyrightholderis reinstatedpermanently
if the copyrightholdernotifiesyouof the violationby somereasonablemeans,this is the firsttime you havereceivednoticeof violationof this
License(foranywork)fromthat copyrightholder,andyoucurethe violationpriorto 30daysafteryourreceiptof the notice.
Termination
of yourrightsunderthis sectiondoesnot terminatethe licenses
of partieswho havereceivedcopiesor rightsfromyou underthis License.if yourrightshavebeenterminatedand not permanentlyreinstatedyoudo
not qua fyto receve new censesfor the samematera undersect on10.
g,AcceptanceNotRequiredfor HavingCopies,
Youarenot requiredto acceptthis Licenseinorderto receiveor runa copyofthe Program.Ancillarypropagationof a coveredworkoccurringsolelyas a consequenceof usingpeer-to-peertransmissionto receivea copy
likewisedoesnot requireacceptance.Howevernothingotherthanthis Licensegrantsyoupermissionto propagateor modifyanycoveredwork. Theseactionsinfringecopyrig_tifyoudo not acceptthis License.Therefore,by
modfy ngor propagatnga coveredwork,you ndcate youracceptanceof th s E_cense
to do so.
10,AutomaticLicensing
of Downstream
Recipients.
Eachtimeyouconveya coveredwork, the recipientautomaticallyreceivesa licensefromthe originallicensors,to run, modifyandpropagatethatwork, subjectto this License.Youarenot responsiblefor enforcingcompliance
by thirdpartieswiththis License.
An "enti!ytransaction"is a transactiontransferringcontrolof anorganizationor substantiallyallassetsof one or subdividinganorganizationor mergingorganizations.
If propagationof a coveredworkresultsfrom anentity
transactioneachpartyto thattransactionwho receivesa copyof the workalsoreceiveswhateverlicensesto the workthe party'spredecessor
in interesthador could giveunderthe previousparagraphplusa rightto posses
_
sionof the Corresponding
Sourceof the workfromthe predecessorininterest,ifthe predecessorhasit or can getit withreasonableefforts.
Youmaynot imposeanyfurther restrictionsonthe exerciseof the rightsgrantedor affirmedunderthis License.Forexampleyoumaynot imposea licensefee,royalty,or otherchargefor exerciseof rightsgrantedunderthis
L cense,andyoumay not n tate tgat on nc udnga cross-ca m or counterca m n a awsut a egngthatanypatentc a m is nfr ngedby makng, us ng,se ng,offerngfor sa e, or mportngthe Programor anyport onof t.
11, Patents,
A "contributor"is a copyrightholderwhoauthorizesuseunderthis Licenseof the Programor a workonwhichthe Programis based.Theworkthus licensed
is calledthe contributor's"contributorversion".
A contributor's"essentialpatentclaims"areall patentclaimsownedor controlledby the contributor,whetheralreadyacquiredor hereafteracquiredthat wouldbeinfringedby somemannerpermittedby this Licenseof making,using,or sellingits contributorversion,but do not includeclaimsthat wouldbeinfringedonlyas a consequenceof furthermodificationofthe contributorversion.For purposesof this definition,"control" includesthe rightto
grantpatentsublicensesina mannerconsistentwiththe requirements
ofthis License.
Eachcontributorgrantsyoua non*exclusiveworldwide,royalty-freepatentlicenseunderthe contributor'sessentialpatentclaims,to make,use,sell,offerfor sale,importand otherwiserun,modifyandpropagatethe contents
of ts contrbutorverson.
Inthe followingthreeparagraphs,a "patentlicense"is anyexpressagreementor commitment,howeverdenominated,not to enforcea patent(suchas anexpresspermissionto practicea patentor covenantnotto suefor patent infringement).
To"gran]"sucha patentlicenseto a partymeansto makesuchan agreementor commitmentnot to enforcea patentagainsttheparty.
If youconveya coveredwork,knowinglyrelyingon a patentlicense,and the Corresponding
Sourceof the workis not availablefor anyoneto copy,freeof chargeandunderthe termsofthis License,througha publiclyavailable
networkserveror otherreadilyaccessiblemeansthenyoumusteither(1)causethe CorrespondingSourceto beso availableor (2)arrangeto depriveyourseffofthe benefitof the patentlicensefor this particularwork or (3)
arrangeina mannerconsistentwiththe requirements
of this Licenseto extendthe patentlicense:[odownstreamrecipients."Knowinglyrelying"meansyou haveactualknowledgethat but for the patentlicenseyourconveyingthe coveredwork ina country or yourrecipient'suseofthe coveredworkina country wouldinfringeoneor more_dentifiable
patentsinthai country'_hatyouhavereasonto believearevalid.
If,pursuantto or in connectionwitha singletransactionor arrangement,
youconvey,or propagateby procuringconveyanceof, a coveredwork, andgrant a patentlicenseto someofthe partiesreceivingthe coveredwork
authorizingthemto use,propagate,modifyor conveya specificcopy offhe coveredwork,thenthe patentlicenseyougrantis automatically
extendedto all recipientsof the coveredworkandworksbasedonit.
A patentlicenseis "discnminatory"if it doesnot includewithinthe scopeof its coverage,prohibitsthe exerciseof, or is conditionedonthe non-exercise
of one or moreof the rightsthatarespecificallygrantedunderthis
License.Youmaynot conveya coveredworkif youarea partyto anarrangement
with a thirdpartythat is inthe businessof distributingsoftware underwhich youmakepaymentto the thirdpartybasedonthe extentof
youractivityof conveyingthe work.andunderwhichthe thirdpart!!grants,to anyofthe partieswhowouldreceivethe coveredworkfromyou, a discriminatorypatentlicense(a)inconnectionwithcopiesof the coveredwork
conveyedby you(or copiesmadefrom thosecopies) or (b) pnmanlyfor aridin connectionwithspecificproductsor compilationsthatcontainthe coveredwork unlessyouenteredintothat arrangementor that patentlicense
wasgranted,priorto 28March 2007.
Nothinginthis Licenseshallbeconstruedas excludingor limitinganyimpliedlicenseor otherdefensesto infringementthat mayotherwisebeavailableto youunderapplicablepatentlaw.
12, NoSurrenderof Others' Freedom,
If conditionsareimposedonyou(whetherby courtorder,agreementor otherwise)that contradictthe conditionsof this Licensetheydo not excuseyou fromthe conditionsof this License.If youcannotconveya coveredwork
so as to satisfysimultaneouslyyourobligationsunderthis Licenseandanyotherpertinentobligationsthenas a consequence
you maynot conveyitat all.Forexample,if youagreeto termsthat obligateyoufo collecta royalty
forfurtherconveyng fromthoseto whomyouconveythe Program,the ony wayyou coud satisfyboththosetermsandth s L censewou d beto refran ent rey fromconveyngthe Program.
13, Usewith the GNUAfferoGeneralPublic License,
Notwithstanding
anyotherprovisionof this License,you havepermissionto linkor combineanycoveredworkwitha work licensedunderversion3 of the GNUAfferoGeneralPublicLicenseintoa singlecombinedwork_and
to conveythe resultingwork. Thetermsof this Licensewill continueto applyto the part which_sthe coveredwork, but the specialrequirements
of the GNUAfferoGeneralPublicLicense,section13,concerninginteraction
througha networkwilrapplyto the combinationassuch.
14, RevisedVersionsof this License.
TheFreeSoftwareFoundationmay publishrevisedand/ornewversionsof the GNUGeneralPublicLicensefromtime to time.Suchnewversionswill besimilarin spiritto the presentversion,but maydifferin detailto address
newproblemsor concerns.
Eachversionis givena distinguishingversionnumber.If the Programspecifiesthat a certainnumberedversionof the GNUGeneralPublicLicense"oranylaterversion"appliesto it,you havethe optionof followingtheterms
andconditionseitherofthat numberedversionor of anylaterversionpublishedby the FreeSoftwareFoundation.If the Programdoesnot specifya versionnumberof the GNUGeneralPublicLicenseyoumaychooseany
versioneverpublishedby the FreeSoftwareFoundation.
If the Programspecifiesthata proxycandecidewhich futureversionsof the GNUGeneralPublicLicensecanbeused that proxy'spublicstatementof acceptanceof a versionpermanently
authorizesyouto choosethatversionfor tile Program.
Laterlicenseversionsmaygiveyouadditionalor differentpermissions.However,noadditionalobligationsareimposed
on anyauthoror copyrightholderas a resultof yourchoosingto follow a laterversion.
15, Disclaimerof Warranty.
THEREISNOWARRANTYTOR
THEPROGRAM.TOTHEEXTENTPERMITTED
BYAPPLICABLELAW.EXCEPT
WHENOTHERWISE
STATEDINWRITINGTHECOPYRIGHT
HOLDERS
AND/OROTHERPARTIES
PROVIDE
THE
PROGRAM
"ASIS"WITHOUTWARRANTY
OF ANYKIND.EITHEREXPRESSED
OR IMPLIEDINCLUDINGBUTNOTLIMITEDTO.THEIMPLIED
WARRANTIES
OF MERCHANTABILITY
ANDFITNESSFORA PARTICULAR
PURPOSE.
THEENTIRERISKASTOTHEQUALITYANDPERFORMANCE
OFTHEPROGRA_ISWITHY_)U.SHOULD
THEPROGRAM
PROVEDEFECTIVE,
YOUASSUMETHECOSTOFALLNECESSARY
SERVICING,
REPAIR
ORCORRECTION.
16, Limitationof Liability.
IN NOEVENT
UNLESSREQUIRED
BY APPLICABLE
LAWORAGREEDTOtN WRITINGWILLANYCOPYRIGHT
HOLDER,ORANY OTHERPARTY
WHOMODIFIES
AND/ORCONVEYS
THEPROGRAM
AS PERMITrED
ABOVE.BELIABLETO YOUFORDAMAGES.
INCLUDINGANYGENERAL.
SPECIALINCIDENTAL
ORCONSEQUENTIAL
DAMAGES
ARISINGOUTOFTHEUSEOR INABILITY
TO USETHEPROGRAM
(INCLUDING
BUTNOT
LIMITEDTO LOSSOFDATAORDATABEINGRENDERED
INACCURATE
OR LOSSE_SUSTAINED
BY YOUORTHIRDPARTIESORA FAILURE
OFTHEPROGRAM
TOOPERATE
WITHANYOTHERPROGRAMS),
EVENIF
SUCHHOLDEROROTHERPARTYHASBEENADVISED
OF THEPOSSIBILITY
OFSUCHDAMAGES.
17, Interpretation
of Sections15and 16,
If the disclaimerof warrantyand limitationof liabilityprovidedabovecannotbegiven locallegaleffectaccordingtotheirterms reviewingcourts shallapplylocal lawthat mostcloselyapproximates
anabsolutewaiverof allcivil
liabilityin connectionwithfhe Program,unlessa warrantyor assumptionof liabilityaccompanies
a copyofthe Programin returnfor a fee.
For assistance
call 1(800) 332-2119
36
Warranty
Mitsubishi Home-Cinema
Television Limited Warranty
MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA, INC. ("MEVSA") warrants as follows to the original purchaser of
this television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects
arising from improper workmanship and/or material:
a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a period
of thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any software incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase at retail. We will
repair or replace, at our option, any defective part without charge for the part. Parts used for replacement may be replaced
with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the
remainder of the original warranty period.
b. Embedded Software. MEVSA warrants that all software developed by MEVSA and _ncorporated into this television set
(the "Embedded Software") will perform in accordance with the functional description of Embedded Software in all material respects, but MEVSA does not warrant that the Embedded Software is error-free. The limited warranty contained in
this section shall continue for a period of one (1)year from the date of the original purchase at retail. If, after prompt notice
within the warranty period, MEVSA determines that the Embedded Software has failed to perform in accordance with such
functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MEVSA shall modify the nonconforming Embedded Software and make available the
modified Embedded Software at no charge to you, which at MEVSA's sole discretion may be fulfilled by means of modification or replacement software contained on a replacement memory card or made available through download via the Internet
or email for Customer installation. The foregoing shall be MEVSA's sole obligation to you under this limited warranty. All
rights under this limited warranty on the Embedded Software also subject to your acceptance of and compliance with the
terms of the Software License Agreement applicable to this television, and this limited warranty on the Embedded Software
shall be null and void if the Embedded Software is modified or changed in any manner except as specifically authorized by
MEVSA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticular
screen if it proves defective. For certain items that are designed to be replaced by the consumer, including (but not limited
to) some Embedded Software and Lamps, the consumer is solely responsible for any replacement labor. For all other parts,
we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one (1) year
from the original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the
applicable warranty time period.
e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the image
using small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of performance and
quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, sometimes a
pixel is continuously active, inactive or the incorrect color. Our standard is clear; MEVSA warrants only that the percentage
of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct
customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your
MITSUBISHI dealer, by writing at the address provided below, calling MEVSA at the 800-332-2119, or by using the support
feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your television
is located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If not, you must
either deliver your television to an authorized service location at your own expense, or pay for any travel and/or transportation costs the service center may charge to and from your home. Actual service labor will be provided without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service. Present
your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please return the
Owner Registration Card so that we can contact you should a question of safety arise which could affect you.
d. To obtain a replacement lamp, order the lamp directly from the MEVSA Parts Department at (800) 553-7278.
For assistance
call 1(800) 332-2119
Warranty
37
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where such
damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than an
authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to carry out any
maintenance as described in the Owner's Guide including air vent cleaning or any product damaged by excessive physical
or electrical stress); any products that have had a serial number or any part thereof altered, defaced or removed; product
use in any manner contrary to the Owner's Guide; freight damage; or any damage caused by acts of God or other factors
beyond the reasonable control of MEVSA, such as power surge damage caused by electrical system or lightning. This
limited warranty also excludes service calls where no defect in the product covered under this warranty is found, service
calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered
under this limited warranty, all costs, expenses or any other damages arising from product installation, or set-ups, any
adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, antenna, cable or satellite systems,
or service of products purchased or serviced outside the U.S.A. Please consult the operating instructions contained in the
Owner's Guide furnished with the product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, MIGHT
ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF
ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MEVSA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF
CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental,
special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the state
where the television was purchased and the laws of such state will govern.
MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
Mitsubishi Home-Cinema Television Limited Warranty (Canada only)
This limited warranty is valid only for products purchased, used and serviced in Canada. MITSUBISHI ELECTRIC
VISUAL SOLUTIONS AMERICA, INC. ("MEVSA") warrants as follows to the original purchaser of this television from an
authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects arising from improper
workmanship and/or material:
a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a period of
thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any software incorporated
into this television) are warranted for a period of one (1)year from the date of the original purchase at retail. We will repair or
replace, at our option, any defective part without charge for the part. Parts used for replacement may be replaced with those
of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the remainder of
the original warranty period.
b. Embedded Software. MEVSA warrants that all software developed by MEVSA and incorporated into this television set
(the "Embedded Software") will perform in accordance with the functional description of Embedded Software in all material respects, but MEVSA does not warrant that the Embedded Software is error-free. The limited warranty contained in this
section shall continue for a period of one (1)year from the date of the original purchase at retail. If, after prompt notice within
the warranty period, MEVSA determines that the Embedded Software has failed to perform in accordance with such functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of
the Embedded Software, then MEVSA shall modify the nonconforming Embedded Software and make available the modified Embedded Software at no charge to you, which at MEVSA's sole discretion may be fulfilled by means of modification or
replacement software contained on a replacement memory card or made available through download via the Internet or email
For assistance
call 1(800) 332-2119
38
Warranty
for Customer installation. The foregoing shall be MEVSA's sole obligation to you under this limited warranty. All rights under
this limited warranty on the Embedded Software also subject to your acceptance of and compliance with the terms of the
Software License Agreement applicable to this television, and this limited warranty on the Embedded Software shall be null
and void if the Embedded Software is modified or changed in any manner except as specifically authorized by MEVSA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticular screen
if it proves defective. For certain items that are designed to be replaced by the consumer, including (but not limited to) some
Embedded Software and Lamps, the consumer is solely responsible for any replacement labor. For all other parts, we will
provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one (1) year from the
original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the
applicable warranty time period.
e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the image using
small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of performance and quality, in
fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MEVSA warrants only that the percentage of properly
functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct
customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your MITSUBISHI dealer or by calling MEVSA at 800-332-2119.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your television
is located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If not, you must
either deliver your television to an authorized service location at your own expense, or pay for any travel and/or transportation
costs the service center may charge to and from your home. Actual service labor will be provided without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service. Present your
sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please return the Owner
Registration Card so that we may contact you should a question of safety arise which could affect you.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where such
damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than an
authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to carry out any
maintenance as described in the Owner's Guide including air vent cleaning or any product damaged by excessive physical or
electrical stress); any products that have had a serial number or any part thereof altered, defaced or removed; product use in
any manner contrary to the Owner's Guide; freight damage; or any damage caused by acts of God or other factors beyond
the reasonable control of MEVSA, such as power surge damage caused by electrical system or lightning. This limited warranty also excludes service calls where no defect in the product covered under this warranty is found, service calls related to
unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered under this limited
warranty, all costs, expenses or any other damages arising from product installation, or set-ups, any adjustments of user
controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for
display or use, connection with any external audio receiver, antenna, cable or satellite systems, or service of products purchased or serviced outside Canada. Please consult the operating instructions contained in the Owner's Guide furnished with
the product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, MIGHT
ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF
ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MEVSA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF
CONTRACT, OR OTHERWISE.
For assistance
call 1(800) 332-2119
Warranty
39
5. Some jurisdictions do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental,
special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from province to province.
MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618
www. Mitsubishi-tv.com
Mitsubishi
Electric
VisualSolutions
America,
Inc. (MEVSA)Internet
Applications
Policy
MEVSA Internet Applications affords the opportunity to access third party Internet product offerings or services ("Third Party
Services") on certain Mitsubishi TVs. The Third Party Services accessible herein are provided as per our agreement with these
third parties. These agreements are subject to change, interruption, suspension (including termination) at any time and for various
reasons. MEVSA makes no warranties or representations that any particular Third Party Service will be accessible, available, function in any particular manner or function at all.
Internet Access Required for Third Party Services; Updates:
To use these Third Party Services, you must obtain high-speed/broadband access to the Internet (such as DSL, cable or T1 lines),
either directly or through devices that access the Internet and pay any service fees associated with such access. In addition, you
must provide all equipment necessary to make such connection to the Internet including a modem or other Internet access device.
Each individual third party Internet product may require different minimum Internet connection speed. The usability and availably
of a functional Mitsubishi television and its internet connected feature may highly be dependent and varied based on high-speed/
broadband internet access, connection speed, bandwidth, other equipment(s), third party applications, firmware updates and other
factors outside of MEVSA'scontrol and/or responsibility which may also be independent of the actual operation of the television. It
is further understood that Mitsubishi televisions are integrated with sophisticated technologies (software and hardware) which may
exhibit delayed boot-up/shutdown time and/or interrupted services. You further understand that the Third Party Services specifications and functionality are constantly evolving and that we may directly, or indirectly via third parties, update or change the Third
Party Services, in whole or in part, at any time and without notice to you. Such updates may be required for you to use certain
aspects of the Third Party services or to continue to connect to the Third Party Services.
Availability of Content on Third Party Services:
MEVSA or said third parties providing Third Party Services reserve the right to delete data from their servers, or prevent access
to their servers or to change data categories, product offerings or service levels for any reason that MEVSA or said third parties
deem sufficient in their sole discretion at any time, without notice. MEVSA may also impose additional or different limits on the use
of or access to certain Third Party Services, in any case and without notice or liability. Some or all of the data or functionality of
the Third Party Services may require additional payment and/or subscription by you. However, in no event will you be charged for
any Third Party Services unless those charges are made known to you in advance. MEVSA makes no warranties or representations of any kind as to the accuracy, currency, or completeness of any information contained on the data servers of such third party
providers of any Third Party Services. Furthermore, we do not review, control, or endorse the content, products or services of
Third Party Services or their data servers.
THIRD PARTY SERVICESARE PROVIDEDSERVICE "AS IS" AND "AS AVAILABLE,"WITHOUT WARRANTY OF ANY KIND
(INCLUDINGANY IMPLIED WARRANTY OF MERCHANTABILITY,NON-INFRINGEMENT,OR FITNESS FOR A PARTICULAR
PURPOSE),TO THE MAXIMUM EXTENTPERMITTED BY LAW. USE OF THE THIRD PARTY SERVICESIS AT YOUR SOLE RISK.
THIS MEANS, FOR EXAMPLE, THAT MEVSA DOES NOT GUARANTEETHAT THE THIRD PARTY SERVICESWILL ALWAYSWORK
PROPERLYOR WORK ATALL. THIS ALSO MEANS WE DO NOT GUARANTEE THATTHE THIRD PARTY SERVICES,CONTENT
OR PRODUCTSWILL BE FREE FROM VIRUSES, HACKS, OR OTHER POTENTIALLYHARMFUL INTRUSIONS. PLEASE NOTE
THAT SOME STATESDO NOT ALLOW SUCH WARRANTY LIMITATIONS,SO THESE LIMITATIONSMAY NOT APPLY TO YOU.
Third Party Services Content Disclaimer:
Certain Third Party Services may include materials from third parties or links to certain third party data servers. You acknowledge
and agree that MEVSA is not responsible for examining or evaluating the content or accuracy of any Third Party Services, their
data servers or related third-party materials. MEVSA does not warrant or endorse and does not assume and will not have any
liability or responsibility for any third-party materials or web sites, or for any other materials, products, or services of third parties.
Links to Third Party Services and any associated links to other data servers are provided solely as a convenience to you. To the
extent provided, content types or descriptions of Third Party Services provided for convenience, and you acknowledge and agree
that MEVSA does not guarantee their accuracy. You understand that by using any of the Third Party Services, you may encounter
content that may be deemed offensive, indecent, or objectionable, which content may or may not be identified as having explicit
language. Nevertheless, you agree to use the Third Party Services at your sole risk and that MEVSA shall have no liability to you for
content that may be found to be offensive, indecent, or objectionable. You agree that you will not use any third-party materials in a
manner that would infringe or violate the rights of any other party, and that MEVSA is not in any way responsible for any such use
by you.
For assistance
call 1(800) 332-2119
MITSUBISHI
ELECTRIC
H_
Website:
E-mail:
www.mitsubishi-tv.com
TVsupport@mevsa.com
Call Consumer
operational
or connection
Relations for
assistance
at 800-332-2119
To order replacement or additional
remote controls or lamp cartridges,
Visit our website www.mitsuparts.com
or call 800-553-7278
Trademark
and License Information
LICENSOR'S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Manufactured under license from Cambridge Mechatronics Ltd.
Rapidfire and the 1... logo are trademarks of Cambridge Mechatronics
Ltd
Apple, iPad, iPhone, iTouch, iTunes, are trademarks of Apple Inc., registered in the U.S. and other countries.
The Bluetooth® word mark and Iogos are registered trademarks owned by Bluetooth SIC, Inc. and any use of such
marks by Mitsubishi Electric is under license. Other trademarks and trade names are those of their respective owners.
f-'f'_
k..._k..j
_,!_...._
I_"_
TM
Manufactured under license from Real Sound Lab, SlA.
CONEQ is a trademark of Real Sound Lab, SIA.
Digital Light Processing@ and DLP® are registered trademarks of Texas Instruments.
Manufactured under license from Dolby Laboratories.
of Dolby Laboratories.
"Dolby," "Pro Logic," and the double-D
HDMI®, the HDMI Logo, and High-Definition Multimedia
Licensing LLC in the United States and other countries.
-_®
symbol are trademarks
Interface are trademarks or registered trademarks of HDMI
Imaging Science Foundation Certified Calibration Controls
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
VUDUTMis a trademark of VUDU, Inc.
XPAND, X3D, X4D, X6D, their respective Iogos and other identifying marks of XPAND and X6D Ltd. are and shall
remain the trade-marks and trade names and exclusive property of X6D Ltd.
"x.v.Color" and the "x.v.Color" logo are trademarks of Sony Corporation.
ChannelView TM, DeepField TM Imager, Easy Connect TM,
EdgeEnhance TM, Plush 1080p® 5G, are trademarks of
Mitsubishi Electric Visual Solutions America, Inc.
SYSTEM RESET
If the TV does not respond to the remote control,
control-panel buttons, or will not power on/off,
press and hold the POWERbutton on the control
panel for ten seconds.
The TV will turn off. Power on the TV and the green
LED will flash quickly for about one minute. Recent
settings changes may be lost.
V45+/V45++/V45CB
© 2011 Mitsubishi Electric Visual Solutions America, Inc.
For Your Records
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
RETAILER NAME
LOCATION
,J
853B740A20