INVERTER
Plug-in option
FR-A7AR
FR-A7AR E kit
INSTRUCTION MANUAL
Relay output function
PRE-OPERATION INSTRUCTIONS
INSTALLATION AND WIRING
(FR-A700/F700 SERIES)
INSTALLATION AND WIRING
(FR-E700 SERIES (E kit))
RELAY OUTPUT
1
2
3
4
Thank you for choosing this Mitsubishi Inverter plug-in option.
This instruction manual gives handling information and
precautions for use of this equipment. Incorrect handling might
cause an unexpected fault. Before using the equipment, please
read this manual carefully to use the equipment to its optimum.
Please forward this manual to the end user.
This section is specifically about
safety matters
Do not attempt to install, operate, maintain or inspect this
product until you have read through this instruction manual and
appended documents carefully and can use the equipment
correctly. Do not use this product until you have a full
knowledge of the equipment, safety information and
instructions.
In this instruction manual, the safety instruction levels are
classified into "WARNING" and "CAUTION".
WARNING
CAUTION
Assumes that incorrect handling may
cause hazardous conditions, resulting
in death or severe injury.
Assumes that incorrect handling may
cause hazardous conditions, resulting
in medium or slight injury, or may
cause physical damage only.
CAUTION level may lead to a serious
Note that even the
consequence according to conditions. Please follow the
instructions of both levels because they are important to
personnel safety.
SAFETY INSTRUCTIONS
1. Electric Shock Prevention
WARNING
• While power is on or when the inverter is running, do not
open the front cover. You may get an electric shock.
• Do not run the inverter with the front cover or wiring cover
removed. Otherwise, you may access the exposed highvoltage terminals and charging part and get an electric shock.
• If power is off, do not remove the front cover except for wiring
or periodic inspection. You may access the charged inverter
circuits and get an electric shock.
• Before starting wiring or inspection, check to make sure that
the indication of the inverter operation panel is off, wait for at
least 10 minutes after the power supply has been switched off,
and check that there are no residual voltage using a tester or
the like. The capacitor is charged with high voltage for some
time after power off and it is dangerous.
• Any person who is involved in the wiring or inspection of this
equipment should be fully competent to do the work.
• Always install the plug-in option before wiring. Otherwise,
you may get an electric shock or be injured.
• Do not touch the plug-in option with wet hands. Otherwise
you may get an electric shock.
• Do not subject the cables to scratches, excessive stress,
heavy loads or pinching. Otherwise you may get an electric
shock.
A-1
2. Injury Prevention
3) Usage
WARNING
CAUTION
• Apply only the voltage specified in the instruction manual to
each terminal. Otherwise, burst, damage, etc. may occur.
• Ensure that the cables are connected to the correct terminals.
Otherwise, burst, damage, etc. may occur.
• Always make sure that polarity is correct to prevent damage, etc.
Otherwise, burst, damage may occur.
• While power is on or for some time after power-off, do not touch
the inverter as it is hot and you may get burnt.
3. Additional Instructions
Also note the following points to prevent an accidental failure,
injury, electric shock, etc.
1) Transportation and mounting
CAUTION
• Do not install or operate the plug-in option if it is damaged or
has parts missing.
• Do not stand or rest heavy objects on the product.
• Check that the mounting orientation is correct.
• Prevent other conductive bodies such as screws and metal
fragments or other flammable substance such as oil from
entering the inverter.
2) Trial run
CAUTION
• When parameter clear or all parameter clear is performed,
reset the required parameters before starting operations.
Each parameter returns to the initial value.
• For prevention of damage due to static electricity, touch
nearby metal before touching this product to eliminate static
electricity from your body.
4) Maintenance, inspection and parts replacement
CAUTION
• Do not test the equipment with a megger (measure insulation
resistance).
5) Disposal
CAUTION
• Treat as industrial waste.
CAUTION
• Before starting operation, confirm and adjust the parameters.
A failure to do so may cause some machines to make
unexpected motions.
A-2
• Do not modify the equipment.
• Do not perform parts removal which is not instructed in this
manual. Doing so may lead to fault or damage of the inverter.
6) General instruction
All illustrations given in this manual may have been drawn with
covers or safety guards removed to provide in-depth
description. Before starting operation of the product, always
return the covers and guards into original positions as specified
and operate the equipment in accordance with the manual.
— CONTENTS —
1 PRE-OPERATION INSTRUCTIONS
1
1.1
Unpacking and Product Confirmation .............................................................................................1
1.2
1.3
Parts ....................................................................................................................................................3
Specifications.....................................................................................................................................4
1.1.1
1.1.2
Packing confirmation (FR-A700/F700 series)................................................................................................. 1
Packing confirmation (FR-E700 series (E kit)) ............................................................................................... 2
2 INSTALLATION AND WIRING (FR-A700/F700 SERIES)
2.1
2.2
2.3
Pre-Installation Instructions .............................................................................................................5
Installation Procedure .......................................................................................................................6
Wiring..................................................................................................................................................8
3 INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
3.1
3.2
3.3
12
Pre-Installation Instructions ...........................................................................................................12
Installation Procedure .....................................................................................................................12
Wiring................................................................................................................................................18
4 RELAY OUTPUT
4.1
4.2
4.3
4.4
4.5
4.6
5
21
Internal Block Diagram....................................................................................................................21
Terminals ..........................................................................................................................................22
Parameter List ..................................................................................................................................22
Output Signal List (FR-A700/F700 series) .....................................................................................23
Output Signal List (FR-E700 series)...............................................................................................25
Connection Diagram When Using Electronic Bypass Sequence Function (FR-A700/F700
series) ...............................................................................................................................................26
I
1
1.1
PRE-OPERATION INSTRUCTIONS
Unpacking and Product Confirmation
Take the plug-in option out of the package, check the product name, and confirm that the product is as you
ordered and intact.
This product is a plug-in option dedicated for the FR-A700/F700/E700 series.
1.1.1
Packing confirmation (FR-A700/F700 series)
Check the enclosed items.
Plug-in option
Mounting screw (M3 × 6mm) Hex-head screw for option
......................................... 1 .............. 2 (Refer to page 6.) mounting (5.5mm)
............... 1 (Refer to page 6.)
5.5mm
1
1
PRE-OPERATION INSTRUCTIONS
1.1.2
Packing confirmation (FR-E700 series (E kit))
Check the enclosed items.
Plug-in option
............................................... 1
Mounting screw (M3 × 6mm)
Front cover for plug-in option
............ 2 (Refer to page 14, 17) ...............1(Refer to page 14, 17)
Option protective cover *1
...................... 1(Refer to page 14)
Option small cover *2
Insulation sheet
................... 1(Refer to page 17) ...............1(Refer to page 14, 17)
*1
Used with the FR-E720-3.7K (FR-E720-175) or less and FR-E740-7.5K (FR-E740-170) or less.
*2
Used with the FR-E720-5.5K (FR-E720-240) or more and FR-E740-11K (FR-E740-230) or more.
CAUTION
• In place of the inverter front cover, install a provided front cover for plug-in option.
2
PRE-OPERATION INSTRUCTIONS
1.2
Parts
Terminal
block
Front view
Mounting
hole
Rear view
Connector
Connect to the inverter
option connector
(Refer to page 14, 17)
Terminal layout
2A
Mounting
hole
Mounting hole
1A
2B
1B
2C
1C
1
3A
3B
3C
3
PRE-OPERATION INSTRUCTIONS
1.3
Specifications
(1) Types of output signal
1 changeover contact output (three relays are provided)
(2) Contact capacity
230VAC .......... 0.3A
30VDC ............ 0.3A
CAUTION
• The contacts should be used within the rated capacity to prevent contacts weld resulting from faster
contacts wearing.
4
2
INSTALLATION AND WIRING (FR-A700/F700 SERIES)
2.1
Pre-Installation Instructions
Make sure that the input power of the inverter is off.
CAUTION
With input power on, do not install or remove the plug-in option. Otherwise, the inverter and
plug-in option may be damaged.
For prevention of damage due to static electricity, touch nearby metal before touching this
product to eliminate static electricity from your body.
2
5
INSTALLATION AND WIRING (FR-A700/F700 SERIES)
2.2
Installation Procedure
1)Remove the inverter front cover.
1)
2)Mount the hex-head screw for option
mounting into the inverter screw hole
(on earth plate). (size 5.5mm,
tightening torque 0.56N⋅m to 0.75N⋅m)
Screw hole for
option mounting
Inverter side
option
connector
Screw hole for
option mounting
(on earth plate)
Hex-head screw
for option mounting
2)
3)
4) Mounting
3)Securely fit the connector of the plug-in
option to the inverter connector along
the guides.
4)Securely fix the both right and left sides
of the plug-in option to the inverter with
the accessory mounting screws.
(Tightening torque 0.45N⋅m to
0.55N⋅m) If the screw holes do not lineup, the connector may not have been
plugged snugly. Check for loose
plugging.
screws
REMARKS
• Remove a plug-in option after removing two screws on both left and right sides.
(When the plug-in option is mounted in the connector 3 (connector 1 for the FR-F700 series), it is easier to remove
the plug-in option after removing a control circuit terminal block.)
6
INSTALLATION AND WIRING (FR-A700/F700 SERIES)
CAUTION
•
•
•
When used with other plug-in options, always connect the FR-A7AR to the connector 1 to prevent malfunction.
Only one type of option per inverter may be used. When two or more options are mounted, priority is in
order of inverter option connectors 1, 2 and 3, the options having lower priority are inoperative.
When the inverter cannot recognize that the option is mounted due to improper
Mounting
Error
installation, etc., "
to
" (option alarm) are displayed for the FRPosition
Display
A700 series. The errors shown differ according to the mounting positions
Connector 1
(connectors 1, 2, 3).
Connector 2
Connector 3
•
•
•
The FR-F700 series has one connection connector for the plug-in option. When the inverter can not
recognize that the option unit is mounted due to improper installation, etc., "
" (option alarm) is
displayed.
Take care not to drop a hex-head screw for option mounting or mounting screw during mounting and removal.
Pull out the option straight to remove. Otherwise, the connector may be damaged.
2
7
INSTALLATION AND WIRING (FR-A700/F700 SERIES)
2.3
Wiring
(1) Untwist the twisted pair shielded cables after stripping its sheath.
Also, perform protective treatment of the shield to ensure that it will not
make contact with the conductive area.
Shield
(perform protective treatment)
Sheath
Strip off the sheath about the size as in the right figure. If the length of the
sheath pealed is too long, a short circuit may occur among neighboring
wires. If the length is too short, wires might come off.
Wire the stripped cable after twisting it to prevent it from becoming loose.
(Do not solder it.)
Use a bar type terminal as required.
Twisted pair
shielded cable
Cable stripping size
6mm
REMARKS
• Information on bar terminals
Commercially available product examples (as of September, 2006)
Wire Size
Bar Terminal Model
With insulation sleeve Without insulation sleeve
(mm2)
0.3 to 0.5
Al 0,5-6WH
A 0,5-6
M3
0.5 to 0.75
Al 0,75-6GY
A 0,75-6
Bar terminal crimping tool: CRIMPFOX ZA3 (Phoenix Contact Co., Ltd.)
Terminal
Screw Size
When using the bar terminal (without insulation sleeve),
use care so that the twisted wires do not come out.
8
Maker
Phoenix Contact
Co.,Ltd.
INSTALLATION AND WIRING (FR-A700/F700 SERIES)
(2) Loosen the terminal screw and insert the cable into the terminal.
Screw Size
M3
Tightening Torque
0.5N⋅m to 0.6N⋅m
Cable Size
Screwdriver
0.3mm2 to 0.75mm2
Small
flat-blade screwdriver
(Tip thickness: 0.4mm/tip width: 2.5mm )
CAUTION
• Undertightening can cause cable disconnection or malfunction. Overtightening can cause a short circuit or
malfunction due to damage to the screw or unit.
2
9
INSTALLATION AND WIRING (FR-A700/F700 SERIES)
(3) For wiring of the FR-A700 series 22K* or less and the FR-F700 series 30K* or less, route wires between
the control circuit terminal block and front cover. If cables can not be routed between the control circuit
terminal block and front cover due to the increased number of cables, remove a hook of the front cover
and use a space become available.
For wiring of the FR-A700 series 30K* or more and the FR-F700 series 37K* or more, use the space
on the left side of the control circuit terminal block.
Cut off
with a
nipper,
etc.
Cut off a hook on the inverter
front cover side surface.
(Cut off so that no portion is left.)
FR-A700 series 22K* or less
and FR-F700 series 30K* or less
Control circuit
terminal block
FR-A700 series 30K* or more
and FR-F700 series 37K* or more
*The inverter type of 22K and 30K of FR-A700 series, 30K and 37K of FR-F700 series in each -NA, -EC versions are as follows.
NA
A700
F700
10
FR-A720-22K
FR-A740-22K
FR-A720-30K
FR-A740-30K
FR-F720-30K
FR-F740-30K
FR-F720-37K
FR-F740-37K
FR-A720-00900-NA
FR-A740-00440-NA (FR-A760-00330-NA)
FR-A720-01150-NA
FR-A740-00570-NA (FR-A760-00550-NA)
FR-F720-01250-NA
FR-F740-00620-NA
FR-F720-01540-NA
FR-F740-00770-NA
EC
⎯
FR-A740-00620-EC
⎯
FR-A740-00770-EC
⎯
FR-F740-00620-EC
⎯
FR-F740-00770-EC
INSTALLATION AND WIRING (FR-A700/F700 SERIES)
REMARKS
• When the hook of the inverter front cover is cut off for wiring, the protective structure (JEM1030) changes to open
type (IP00).
CAUTION
When performing wiring using the space between the inverter front cover and control circuit
terminal block, take care not to subject the cable to stress.
After wiring, wire offcuts must not be left in the inverter. They may cause a fault, failure or
malfunction.
2
11
3
INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
3.1
Pre-Installation Instructions
Make sure that the input power of the inverter is off.
CAUTION
With input power on, do not install or remove the plug-in option. Otherwise, the inverter and
plug-in option may be damaged.
For prevention of damage due to static electricity, touch nearby metal before touching this
product to eliminate static electricity from your body.
3.2
Installation Procedure
The FR-E700 series has one connection connector for the plug-in option.
CAUTION
•
Always perform wiring to the main circuit terminals and control circuit terminals before installing the
option. Wiring cannot be performed after installing the option.
•
When the inverter cannot recognize that the option is mounted due to improper installation, etc., "
(option alarm) is displayed.
Take care not to drop a mounting screws during mounting and removal.
Pull out the option straight to remove. Otherwise, the connector may be damaged.
•
•
12
"
INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
z For FR-E720-3.7K (FR-E720-175) or less, FR-E740-7.5K (FR-E740-170) or less
(1) Remove the front cover from the inverter. (For removing the front cover, refer to the FR-E700 series
instruction manual.)
(2) Remove the PU cover from the front cover. Open the PU cover with a driver, etc. and remove it in the
direction of arrow as shown below.
(1) Front cover
*
(2) PU cover
* Open the PU cover, then open it toward the arrow
direction to remove.
REMARKS
• Because the voltage class, model name and serial (only voltage class is labeled for the FR-E740-5.5K (FR-E740120) or more) are stated on the PU cover, replace a PU cover of a plug-in option front cover with the removed PU
cover from the inverter.
3
13
INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
(3) Install the option protective cover.
(4) Correctly install the insulating sheet between the inverter and plug-in option. (Refer to page 15 for
installation method of an insulation sheet.)
(5) Securely fit the connector of the plug-in option to the inverter connector along the guides.
(6) Securely fix the both top and bottom of the plug-in option to the inverter with the accessory mounting
screws.(tightening torque 0.45N⋅m to 0.55N⋅m) If the screw holes do not line-up, the connector may not
have been plugged snugly. Check for loose plugging.
(7) Remove the PU cover provided on the front cover for plug-in option and install the other PU cover,
which was removed in (2).
(8) When wiring to the plug-in option is completed, install the front cover for plug-in option to the inverter.
(4) Insulation sheet
(Available only
Front cover
for FR-A7AR)
for plug-in option
plug-in option
(8)
(5)
Option connector
of inverter
(7) Replace
(3) Option protective cover
(6)
Mounting screws
14
INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
z Installation of an insulation sheet
For FR-A7AR, put an insulation sheet under the screw platform of inverter (A of the following figure) and
fit the insulation sheet to the screw position on the inverter side (B of the following figure).
A
B
CAUTION
• If an insulation sheet is not installed, the inverter and plug-in option may malfunction.
3
15
INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
z For FR-E720-5.5K (FR-E720-240) or more, FR-E740-11K (FR-E740-230) or more
(1) Remove the front cover 1 and 2 from the inverter. (For removing the front cover, refer to the FR-E700
series instruction manual.)
(2) Remove the PU cover from the front cover 2. For removing the PU cover, refer to page 13.
(3) Cut off the dummy cover of the front cover 1 with a nipper, etc. and make a space for installing the
option small cover.
Front cover 1
(1)
Front cover 2
(1)
(2)
(3)
PU cover
Dummy cover
Cut off the edges so that no burr is left.
REMARKS
• Because voltage is stated on the PU cover, replace a PU cover of a plug-in option front cover with the removed PU
cover from the inverter.
16
INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
(4) Correctly install the insulating sheet between the inverter and plug-in option. (Refer to page 15 for
installation method of an insulation sheet.)
(5) Securely fit the connector of the plug-in option to the inverter connector along the guides.
(6) Securely fix the both top and bottom of the plug-in option to the inverter with the accessory mounting
screws. (tightening torque 0.45N⋅m to 0.55N⋅m) If the screw holes do not line-up, the connector may
not have been plugged snugly. Check for loose plugging.
(7) Remove the PU cover provided on the front cover for plug-in option and install the other PU cover,
which was removed in (2).
(8) When wiring to the plug-in option is completed, install the front cover for plug-in option to the inverter.
(9) Install the option small cover to the front cover 1.
(10) Install the front cover 1 to the inverter.
(5) Option connector of inverter
Front cover for
plug-in option (4) Insulation sheet
(10)
(8)
(7) Replace
(9)
plug-in option
(6) Mounting screws
3
Option small cover
17
INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
3.3
Wiring
(1) Untwist the twisted pair shielded cables after stripping its sheath.
Also, perform protective treatment of the shield to ensure that it will not
make contact with the conductive area.
Shield
(perform protective treatment)
Sheath
Strip off the sheath about the size as in the right figure. If the length of the
sheath pealed is too long, a short circuit may occur among neighboring
wires. If the length is too short, wires might come off.
Wire the stripped cable after twisting it to prevent it from becoming loose.
(Do not solder it.)
Use a bar type terminal as required.
Twisted pair
shielded cable
Cable stripping size
6mm
REMARKS
• Information on bar terminals
Commercially available product examples (as of September, 2006)
Wire Size
Bar Terminal Model
With insulation sleeve Without insulation sleeve
(mm2)
0.3 to 0.5
Al 0,5-6WH
A 0,5-6
M3
0.5 to 0.75
Al 0,75-6GY
A 0,75-6
Bar terminal crimping tool: CRIMPFOX ZA3 (Phoenix Contact Co., Ltd.)
Terminal
Screw Size
When using the bar terminal (without insulation sleeve),
use care so that the twisted wires do not come out.
18
Maker
Phoenix Contact
Co.,Ltd.
INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
(2) Loosen the terminal screw and insert the cable into the terminal.
Screw Size
Tightening Torque
Cable Size
Screwdriver
M3
0.5N⋅m to 0.6N⋅m
0.3mm2 to 0.75mm2
Small
flat-blade screwdriver
(Tip thickness: 0.4mm/tip width: 2.5mm )
CAUTION
• Undertightening can cause cable disconnection or malfunction. Overtightening can cause a short circuit or
malfunction due to damage to the screw or unit.
3
19
INSTALLATION AND WIRING (FR-E700 SERIES (E kit))
(3) When wiring the FR-E700 series, if a hook of the front cover for the plug-in option impedes wiring, cut
off the hook and perform wiring.
Cut off with a
nipper, etc.
Cut off a hook at the bottom
of the option cover.
(Cut off so that no portion is left.)
REMARKS
•
When the option protective cover or option small cover is not fitted or wire is not passed through even if
the hook of the front cover of the plug-in option has been cut off, the protective structure (JEM1030)
changes to open type (IP00).
CAUTION
When wiring, take care not to subject the cable to stress.
After wiring, wire offcuts must not be left in the inverter. They may cause a fault, failure or
malfunction.
20
4
4.1
RELAY OUTPUT
Internal Block Diagram
You can select any three output signals (RUN, SU, FU, etc.) available with an inverter as standard, and
output them as relay contact signals.
Refer to page 23, 25 of the Instruction Manual (detailed) for details.
The following is the internal block diagram of the FR-A7AR.
1C
RA1
1B
1A
2C
Connector
Controller
RA2
2B
2A
3C
RA3
3B
3A
21
4
RELAY OUTPUT
4.2
Terminals
Terminal Symbol
2A
1A
1B
1C
2A
2B
2C
3A
3B
3C
1A
2B
1B
2C
1C
3A
3B
3C
Description
Relay RA1's normally open contact terminal
Relay RA1's normally closed contact terminal
Relay RA1's contact common terminal
Relay RA2's normally open contact terminal
Relay RA2's normally closed contact terminal
Relay RA2's contact common terminal
Relay RA3's normally open contact terminal
Relay RA3's normally closed contact terminal
Relay RA3's contact common terminal
*The operation of each relay depends on the output signal selected.
4.3
Parameter List
By installing this plug-in option, the parameters below are extended.
Set the values according to need.
*1
*2
Parameter Number
Name
Initial Value
320
321
322 *1
RA1 output selection
RA2 output selection
RA3 output selection
0
1
2 (4) *2
When the FR-A7AR and FR-A7AC (support FR-A700 series only) are mounted to inverter at the same time, Pr.
322 can not be set nor displayed.
For the FR-E700 series only, the initial value of Pr. 322 is "4".
Use Pr. 320 to Pr. 322 to select signals used for relay output. (Refer to page 23, 25 for signal types.)
REMARKS
• When an option alarm (
22
to
) occurs, all outputs are tuned off.
RELAY OUTPUT
4.4
Output Signal List (FR-A700/F700 series)
For details of signal definitions, refer to Pr. 190 to Pr. 196 (Output terminal function selection) of the inverter
(FR-A700/F700 series) manual.
Setting
Signal
Positive Name
logic
0
1
RUN
SU
2
IPF
3
4
5
6
7
8
10
11
12
13
14
15
16
17
18
19
OL
FU
FU2
FU3
RBP
THP
PU
RY
Y12
Y13
FDN
FUP
RL
MC1
MC2
MC3
Function
Inverter running
Up to frequency
Instantaneous power failure/
undervoltage
Overload alarm
Output frequency detection
Second output frequency detection
Third output frequency detection *1
Regenerative brake prealarm *2
Electronic thermal relay function prealarm
PU operation mode
Inverter operation ready
Output current detection
Zero current detection
PID lower limit
PID upper limit
PID forward/reverse rotation output
Electronic bypass MC1
Electronic bypass MC2
Electronic bypass MC3
Setting
Signal
Positive Name
logic
20
25
26
27
28
30
31
32
33
34
35
36
39
41
42
43
44
45
BOF
FAN
FIN
ORA
ORM
Y30
Y31
Y32
RY2
LS
TU
Y36
Y39
FB
FB2
FB3
RUN2
RUN3
46
Y46
Function
Brake opening request *1
Fan fault output
Heatsink overheat pre-alarm
Orientation completion *1
Orientation fault *1
Forward rotation output *1
Reverse rotation output *1
Regenerative status output *1
Operation ready 2 *1
Low speed output *1
Torque detection *1
In-position *1
Start-time tuning completion signal *1
Speed detection *1
Second speed detection *1
Third speed detection *1
Inverter running 2 *1
Inverter running and start command is on
During deceleration at occurrence of
power failure (retained until release)
23
4
RELAY OUTPUT
Setting
Signal
Positive Name
logic
47
64
70
71
72
73
74
75
76
77
78
84
*1
*2
*3
*4
PID
During PID control activated
Y64 During retry
SLEEP PID output interruption
Commercial-power supply side motor 1
RO1
connection RO1 *4
Commercial-power supply side motor 2
RO2
connection RO2 *4
Commercial-power supply side motor 3
RO3
connection RO3 *4
Commercial-power supply side motor 4
RO4
connection RO4 *4
RIO1 Inverter side motor 1 connection RIO1 *4
RIO2 Inverter side motor 2 connection RIO2 *4
RIO3 Inverter side motor 3 connection RIO3 *4
RIO4 Inverter side motor 4 connection RIO4 *4
RDY Position control preparation ready *1
Setting
Signal
Positive Name
logic
85
86
87
88
89
90
91
94
95
96
97
98
99
9999
Y85
Y86
Y87
Y88
Y89
Y90
Y91
ALM2
Y95
REM
ER
LF
ALM
⎯
Function
DC feeding *1
Control circuit capacitor life *3
Main circuit capacitor life *3
Cooling fan life *3
Inrush current limit circuit life *3
Life alarm
Alarm output 3 (power-off signal)
Alarm output 2
Maintenance timer signal
Remote output
Minor fault output 2 *1
Minor fault output
Alarm output
No function
They can be set for the FR-A700 series only.
For the FR-F700 series, this function is available with the 75K (FR-F720-03160, FR-F740-01800) or more.
Pr. 190 to Pr. 196 can not be set.
Setting can be made only for FR-F700 series NA, EC and CH version.
REMARKS
• Negative logic can not be set.
24
Function
RELAY OUTPUT
4.5
Output Signal List (FR-E700 series)
For details of signal definitions, refer to Pr. 190 to Pr. 192 (Output terminal function selection) of the inverter
(FR-E700 series) manual.
Setting
Signal
Positive Name
logic
0
1
3
4
7
8
11
12
13
14
15
16
20
RUN
SU
OL
FU
RBP
THP
RY
Y12
Y13
FDN
FUP
RL
BOF
Function
Inverter running
Up to frequency
Overload alarm
Output frequency detection
Regenerative brake prealarm
Electronic thermal relay function prealarm
Inverter operation ready
Output current detection
Zero current detection
PID lower limit
PID upper limit
PID forward/reverse rotation output
Brake opening request
Setting
Signal
Positive Name
logic
25
26
FAN
FIN
46
Y46
47
64
90
91
95
96
98
99
9999
PID
Y64
Y90
Y91
Y95
REM
LF
ALM
⎯
Function
Fan fault output
Heatsink overheat pre-alarm
During deceleration at occurrence of
power failure (retained until release)
During PID control activated
During retry
Life alarm
Alarm output 3 (power-off signal)
Maintenance timer signal
Remote output
Minor fault output
Alarm output
No function
REMARKS
• Negative logic can not be set.
25
4
RELAY OUTPUT
4.6
Connection Diagram When Using Electronic Bypass Sequence
Function (FR-A700/F700 series)
When using the electronic bypass sequence function with the FR-A7AR mounted to the FR-A700/F700
series inverter, it is recommended to use either connection shown below.
(1) Recommended connection example 1
MC2
MCCB
MC1
Power
supply
(2) Recommended connection example 2
When using relay output of the FR-A7AR,
set the alarm output signal (ALM) instead
of the MC1 signal and output it from
contacts B and C.
26
Inverter
R/L1
U
S/L2
V
T/L3
W
R1/L11
S1/L21 FR-A7AR
MC1 A
C
MC2 A
C
A
MC3
C
Motor
MC3
IM
MC1
MC3
MC2
MC2
MC3
MC2
MCCB
Power
supply
MC1
Inverter
R/L1
U
S/L2
V
T/L3
W
R1/L11 FR-A7AR
S1/L21
B
ALM C
A
MC2 C
MC3 A
C
Motor
MC3
IM
MC1
MC3
MC2
MC2
MC3
MEMO
27
REVISIONS
*The manual number is given on the bottom left of the back cover.
Print Date
May, 2004
Dec., 2004
*Manual Number
Revision
IB(NA)-0600166ENG-A First edition
IB(NA)-0600166ENG-B Partial modification
Board shape change
Addition
Compatible with the FR-F700-NA series
Sep., 2005
IB(NA)-0600166ENG-C
Addition
Compatible with the FR-A700 series
Dec., 2007
IB(NA)-0600166ENG-D
Addition
Compatible with the FR-E700 series
28
IB(NA)-0600166ENG-D