Bosch 36 V-LI Operating instructions

Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
www.bosch-pt.com
GBH 36 V-LI Compact Professional
1 619 929 797 (2007.12) T / 306
de
en
fr
es
pt
it
nl
Originalbetriebsanleitung
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
Oorspronkelijke
gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el
tr
pl
cs
sk
hu
ru
uk
Πρωτότυπο οδηγιών χρήσης
Orijinal işletme talimat
Instrukcją oryginalną
Původním návodem k
používání
Pôvodný návod na použitie
Eredeti használati utasítás
Одлинник руководства по
эксплуатации
Оригінальна інструкція з
експлуатації
ro Instrucţiuni de folosire
originale
bg Оригинално ръководство
за експлоатация
sr Originalno uputstvo za rad
sl Izvirna navodila
hr Originalne upute za rad
et Algupärane kasutusjuhend
lv Instrukcijām
oriģinālvalodā
lt Originali
instrukcija
3|
A
B
10
1
9
2
X
16
16
D
C
4
19
18
18
17
E
1 619 929 797 | (3.12.07)
F
4
Bosch Power Tools
4|
H
G
X
21
20
16
J
I
6
1 619 929 797 | (3.12.07)
22
23
24
25
9
4
26
Bosch Power Tools
5|
5
4
1
2
3
6
7
8
9
10
11
12
16
15
1 619 929 797 | (3.12.07)
14
13
Bosch Power Tools
English | 17
General Power Tool
Safety Warnings
en
WARNING Read all safety warnings and all
instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away
while operating a power tool. Distractions can cause you to lose control.
2) Electrical safety
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing
and use common sense when operating
a power tool. Do not use a power tool
while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating
power tools may result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce
risk of electric shock.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on
the switch or energising power tools that
have the switch on invites accidents.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your
body is earthed or grounded.
d) Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected situations.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges and moving parts.
Damaged or entangled cords increase the
risk of electric shock.
Bosch Power Tools
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewellery or long hair can
be caught in moving parts.
1 619 929 797 | (3.12.07)
18 | English
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that
may affect the power tool’s operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
1 619 929 797 | (3.12.07)
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack
may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a
connection from one terminal to another.
Shorting the battery terminals together
may cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that
the safety of the power tool is maintained.
Machine-specific
Safety Warnings
f Wear hearing protection. Exposure to noise
can cause hearing loss.
f Always use the auxiliary handle supplied
with the machine. Loss of control can cause
personal injury.
f Use appropriate detectors to determine if
utility lines are hidden in the work area or
call the local utility company for assistance.
Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can
lead to explosion. Penetrating a water line
causes property damage or may cause an
electric shock.
Bosch Power Tools
English | 19
f When working with the machine, always
hold it firmly with both hands and provide
for a secure stance. The power tool is guided
more secure with both hands.
f Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held
more secure than by hand.
f Keep your workplace clean. Blends of materials are particularly dangerous. Dust from
light alloys can burn or explode.
f Always wait until the machine has come to
a complete stop before placing it down. The
tool insert can jam and lead to loss of control
over the power tool.
f Avoid unintentional switching on. Ensure the
On/Off switch is in the off position before inserting battery pack. Carrying the power tool
with your finger on the On/Off switch or inserting the battery pack into power tools that
have the switch on invites accidents.
f Do not open the battery. Danger of shortcircuiting.
Protect the battery against heat, e.g.,
also against continuous sun irradiation
and fire. There is danger of explosion.
f In case of damage and improper use of the
battery, vapours may be emitted. Provide
for fresh air and seek medical help in case
of complaints. The vapours can irritate the
respiratory system.
f When the battery is defective, liquid can
escape and come into contact with adjacent
components. Check any parts concerned.
Clean such parts or replace them, if required.
f Use the battery only in conjunction with your
Bosch power tool. This measure alone protects the battery against dangerous overload.
Functional Description
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or
serious injury.
While reading the operating instructions, unfold
the graphics page for the machine and leave it
open.
Bosch Power Tools
Intended Use
The machine is intended for hammer drilling in
concrete, brick and stone. It is also suitable for
drilling without impact in wood, metal, ceramic
and plastic. Machines with electronic control
and right/left rotation are also suitable for
screwdriving.
Product Features
The numbering of the product features refers to
the illustration of the machine on the graphics
page.
1
2
3
4
5
6
7
8
9
Depth stop
SDS-plus tool holder
Dust protection cap
Locking sleeve
Vibration damper
Rotational direction switch
On/Off switch
Selector switch for drilling/hammer drilling
Button for depth stop adjustment
10 Wing bolt for adjustment of auxiliary handle
11 Battery*
12 Battery unlocking button
13 Temperature control indicator
14 Battery charge-control indicator
15 Button for charge-control indicator
16 Auxiliary handle
17 Securing screw for key type drill chuck*
18 Key type drill chuck*
19 SDS-plus adapter shank for drill chuck*
20 Extraction sleeve of the dust extraction
attachment*
21 Clamping screw for the dust extraction
attachment*
22 Depth stop of the dust extraction
attachment*
23 Telescopic pipe of the dust extraction
attachment*
24 Wing bolt of the dust extraction attachment*
25 Guide pipe of the dust extraction
attachment*
26 Universal bit holder with SDS-plus shank*
*The accessories illustrated or described are not
included as standard delivery.
1 619 929 797 | (3.12.07)
20 | English
Technical Data
Rotary Hammer
GBH 36 V-LI
Compact
Professional
Article number
3 611 J03 R..
Speed control
z
Right/left rotation
z
Rated voltage
V=
36
Rated power input
W
430
Output power
W
320
bpm
0 – 4850
J
0 – 1.7
Impact frequency at
rated speed
Impact energy per stroke
Rated speed
rpm
Tool holder
0 – 1500
SDS-plus
Spindle collar diameter
mm
48
Drilling diameter, max.:
– Concrete
– Steel
– Wood
mm
mm
mm
18
13
30
max. diameter screw
mm
6
kg
2.9
Weight according to
EPTA-Procedure 01/2003
Please observe the article number on the type plate
of your machine. The trade names of the individual
machines may vary.
Noise/Vibration Information
Measured values determined according to
EN 60745.
Typically the A-weighted noise levels of the
product are: Sound pressure level 91 dB(A);
Sound power level 102 dB(A). Uncertainty
K =3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined according to EN 60745:
Hammer drilling into concrete: Vibration emission value ah =10 m/s2, Uncertainty K=1.5 m/s2.
1 619 929 797 | (3.12.07)
The vibration emission level given in this information sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another.
It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main applications of the tool. However
if the tool is used for different applications, with
different accessories or poorly maintained, the
vibration emission may differ. This may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times
when the tool is switched off or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the
total working period.
Identify additional safety measures to protect
the operator from the effects of vibration
such as: maintain the tool and the accessories,
keep the hands warm, organisation of work
patterns.
Declaration of Conformity
We declare under our sole responsibility that the
product described under “Technical Data” is in
conformity with the following standards or standardization documents: EN 60745 according to
the provisions of the directives 2004/108/EC,
98/37/EC (until Dec. 28, 2009), 2006/42/EC
(from Dec. 29, 2009 on).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
09.10.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Bosch Power Tools
English | 21
Assembly
Battery Charging
f Use only the battery chargers listed on the
accessories page. Only these battery chargers are matched to the lithium ion battery of
your power tool.
Note: The battery is supplied partially charged.
To ensure full capacity of the battery, completely charge the battery in the battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any
time without reducing its service life. Interrupting the charging procedure does not damage the
battery.
The lithium ion battery is protected against
deep discharging by the “Electronic Cell Protection (ECP)”. When the battery is empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
WARNING Do not continue to press the
On/Off switch after the machine
has been automatically switched off. The battery can be damaged.
Removing the Battery
The battery 11 is equipped with two locking levels that should prevent the battery from falling
out when pushing the battery unlocking button
12 unintentionally. As long as the battery is inserted in the power tool, it is held in position by
means of a spring.
To remove the battery 11:
– Push the battery against the base of the
power tool (1.) and at the same time press
the battery unlocking button 12 (2.).
– Pull the battery out of the power tool until a
red stripe becomes visible (3.).
– Press the battery unlocking button 12 again
and pull out the battery completely.
Bosch Power Tools
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator 14 indicate the charge condition of
the battery 11. For safety reasons, it is only possible to check the status of the charge condition
when the machine is at a standstill.
Push button 15 to indicate the charge condition
(also possible when the battery is removed).
The battery charge-control indicator automatically goes out after approx. 5 seconds.
LED
Capacity
Continuous lighting 3 x green
≥2/3
Continuous lighting 2 x green
≥1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
When no LED lights up after pushing button 15,
then the battery is defective and must be replaced.
During the charging procedure, the three green
LEDs light up one after the other and briefly go
out. The battery is fully charged when the three
green LEDs light up continuously. The three
LEDs go out again approx. 5 minutes after the
battery has been fully charged.
The battery is equipped with a NTC temperature
control which allows charging only within a temperature range of between 0 °C and 45 °C. A long
battery service life is achieved in this manner.
Auxiliary Handle
f Operate your machine only with the auxiliary
handle 16.
Rotating the Auxiliary Handle (see figure A)
The auxiliary handle 16 can be set to any position
for a secure and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle 10 in anticlockwise direction and set
the auxiliary handle 16 to the required position.
Then tighten the wing bolt 10 again in clockwise
direction.
Adjusting the Drilling Depth (see figure B)
The required drilling depth X can be set with the
depth stop 1.
Press the button for the depth stop adjustment
9 and insert the depth stop into the auxiliary
handle 16.
1 619 929 797 | (3.12.07)
22 | English
The knurled surface of the depth stop 1 must
face downward.
Insert the SDS-plus drilling tool to the stop into
the SDS-plus tool holder 2. Otherwise, the movability of the SDS-plus drilling tool can lead to
incorrect adjustment of the drilling depth.
Pull out the depth stop until the distance between the tip of the drill bit and the tip of the
depth stop correspond with the desired drilling
depth X.
Selecting Drill Chucks and Tools
For hammer drilling, SDS-plus tools are required
that are inserted in the SDS-plus drill chuck.
For drilling without impact in wood, metal,
ceramic and plastic as well as for screwdriving,
tools without SDS-plus are used (e. g., drills
with cylindrical shank). For these tools, a keyless chuck or a key type drill chuck are required.
Changing the Key Type Drill Chuck
To work with tools without SDS-plus (e.g., drills
with cylindrical shank), a suitable drill chuck
must be mounted (key type drill chuck or keyless chuck, accessories).
Mounting the Key Type Drill Chuck
(see figure C)
Screw the SDS-plus adapter shank 19 into a
key type drill chuck 18. Secure the key type drill
chuck 18 with the securing screw 17. Please
observe that the securing screw has a lefthand thread.
Changing the Tool
The dust protection cap 3 largely prevents the
entry of drilling dust into the tool holder during
operation. When inserting the tool, take care
that the dust protection cap 3 is not damaged.
f A damaged dust protection cap should be
changed immediately. We recommend having this carried out by an after-sales service.
Inserting SDS-plus Drilling Tools (see figure E)
The SDS-plus drill chuck allows for simple and
convenient changing of drilling tools without the
use of additional tools.
Clean and lightly grease the shank end of the
tool.
Insert the tool in a twisting manner into the tool
holder until it latches itself.
Check the latching by pulling the tool.
As a requirement of the system, the SDS-plus
drilling tool can move freely. This causes a certain radial run-out at no-load, which has no
effect on the accuracy of the drill hole, as the
drill bit centres itself upon drilling.
Removing SDS-plus Drilling Tools
(see figure F)
Push back the locking sleeve 4 and remove the
tool.
Inserting Drilling Tools without SDS-plus
Note: Do not use tools without SDS-plus for hammer drilling! Tools without SDS-plus and their
drill chucks are damaged by hammer drilling.
Inserting the Key Type Drill Chuck
(see figure D)
Insert a key type drill chuck 18 (see “Changing
the Key Type Drill Chuck”, page 22).
Clean the shank end of the adapter shank and
apply a light coat of grease.
Open the key type drill chuck 18 by turning until
the tool can be inserted. Insert the tool.
Insert the key type drill chuck with the adapter
shank into the tool holder with a turning motion
until it automatically locks.
Insert the chuck key into the corresponding
holes of the key type drill chuck 18 and clamp
the tool uniformly.
Check the locking effect by pulling the key type
drill chuck.
Set the selector switch 8 to the “Drilling” symbol.
Removing the Key Type Drill Chuck
Turn the sleeve of the key type drill chuck 18
with the drill chuck key in anticlockwise direction until the drilling tool can be removed.
Push the locking sleeve 4 toward the rear and
pull out the key type drill chuck 18.
1 619 929 797 | (3.12.07)
Removing Drilling Tools without SDS-plus
Bosch Power Tools
English | 23
Dust Extraction with the Dust
Extraction Attachment (Accessory)
f Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one’s health. Touching or breathing-in the dusts can cause allergic reactions and/or lead to respiratory infections of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in
connection with wood-treatment additives
(chromate, wood preservative). Materials
containing asbestos may only be worked by
specialists.
– Use dust extraction whenever possible.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filterclass respirator.
Observe the relevant regulations in your
country for the materials to be worked.
Mounting the Dust Extraction Attachment
(see figure G)
For dust extraction, the dust extraction attachment (accessory) is required. When drilling, the
dust extraction attachment retracts so that the
attachment head is always close to the surface
at the drill hole.
Press the button for depth stop adjustment 9
and remove the depth stop 1. Press button 9
again and insert the dust extraction attachment
into the auxiliary handle 16 from the front.
Connect an extraction hose (diameter 19 mm,
accessory) to the extraction sleeve 20 of the
dust extraction attachment.
The vacuum cleaner must be suitable for the
material being worked.
When vacuuming dry dust that is especially
detrimental to health or carcinogenic, use a
special vacuum cleaner.
Adjusting the Drilling Depth on the Dust
Extraction Attachment (see figure H)
The required drilling depth X can also be adjusted when the dust extraction attachment is
mounted.
Bosch Power Tools
Insert the SDS-plus drilling tool to the stop into
the SDS-plus tool holder 2. Otherwise, the movability of the SDS-plus drilling tool can lead to
incorrect adjustment of the drilling depth.
Loosen the wing bolt 24 on the dust extraction
attachment.
Without switching the power tool on, apply it
firmly to the drilling location. The SDS-plus drilling tool must face against the surface.
Position the the guide pipe 25 of the dust extraction attachment in its holding fixture in such
a manner that the head of the dust extraction attachment faces against the surface to be drilled.
Do not slide the guide pipe 25 further over the
telescopic pipe 23 of the dust extraction attachment than required, so that as much as possible
of the scale 23 on the telescopic pipe remains
visible.
Retighten the wing bolt 24 again. Loosen the
clamping screw 21 on the depth stop of the dust
extraction attachment.
Move the depth stop 22 on the telescopic pipe
23 in such a manner that the clearance X shown
in the figure corresponds with the required drilling depth.
Tighten the clamping screw 21 in this position.
Operation
Starting Operation
Inserting the Battery
f Use only original Bosch lithium ion batteries with the voltage listed on the nameplate
of your power tool. Using other batteries can
lead to injuries and pose a fire hazard.
Set the rotational direction switch 6 to the centre position to protect the power tool against
accidental starting.
Insert the charged battery 11 from the front into
the base of the power tool. Push the battery
completely into the base until the red stripe can
no longer be seen and the battery is securely
locked.
1 619 929 797 | (3.12.07)
24 | English
Setting the Operating Mode
With the selector switch for drilling/hammer
drilling 8, the operating mode of the machine is
selected.
Note: Change the operating mode only when the
machine is switched off! Otherwise, the machine can be damaged.
To change the operating mode, turn the selector
switch for “drilling/hammer drilling” 8 to the requested position.
Position for hammer drilling in concrete or stone
Position for drilling without impact
in wood, metal, ceramic and plastic
as well as for screwdriving
Reversing the Rotational Direction
(see figure I)
The rotational direction switch 6 is used to reverse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 7 actuated.
Right rotation: Push the rotational direction
switch 6 left to the stop.
Left rotation: Push the rotational direction
switch 6 right to the stop.
For hammer drilling and drilling, always set the
direction of rotation to right rotation.
Switching On and Off
To start the machine, press the On/Off switch 7.
When starting the machine for the first time, a
starting delay is possible, as the electronic system of the power tool has to configure itself first.
To switch off the machine, release the On/Off
switch 7.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on power tool can be variably adjusted, depending on
how far the On/Off switch 7 is pressed.
Light pressure on the On/Off switch 7 results in
low speed/impact rate. Further pressure on the
switch increases the speed/impact rate.
1 619 929 797 | (3.12.07)
Safety Clutch
f If the tool insert becomes caught or
jammed, the drive to the drill spindle is interrupted. Because of the forces that occur,
always hold the power tool firmly with both
hands and provide for a secure stance.
f If the power tool jams, switch the machine
off and loosen the tool insert. When switching the machine on with the drilling tool
jammed, high reaction torques can occur.
Temperature Control Indicator
The red LED of the temperature control indicator 13 signals that the battery or the electronics
of the power tool (when the battery is inserted)
are not within the optimum temperature range.
In this case, the power tool will not operate at
full capacity.
Temperature control of the battery:
– The red LED 13 lights up continuously after
inserting the battery into the charger: The
battery is not within the charging temperature range between 0 °C and 45 °C and cannot be charged.
– The red LED 13 flashes when pushing button
15 or pressing the On/Off switch 7 (when the
battery is inserted): The battery is not wihin
the temperature range for operation of
– 10 °C to +60 °C.
– For battery temperatures over 70 °C, the
power tool switches off until the battery is in
the optimal temperature range again.
Temperature control of the power tool electronics:
– The red LED 13 lights up continuously when
pressing the On/Off switch 7: The temperature of the machine's electronics is below
5 °C or above 75 °C.
– At a temperature above 90 °C , the electronics of the power tool switch off until the temperature is within the allowable temperature
range again.
Bosch Power Tools
English | 25
Working Advice
Maintenance and Service
Vibration Damper
Maintenance and Cleaning
The integrated vibration damper reduces occurring vibrations.
The soft grip handle increases the safety against
slipping off and thus provides for a better grip
and handling of the power tool.
Inserting Screwdriver Bits (see figure J)
f Apply the power tool to the screw/nut only
when it is switched off. Rotating tool inserts
can slip off.
To work with screwdriver bits, a universal bit
holder 26 with SDS-plus shank (accessory) is required.
Clean the shank end of the adapter shank and
apply a light coat of grease.
Insert the universal bit holder with a turning
motion into the tool holder until it automatically
locks.
Check the locking effect by pulling the universal
bit holder.
Insert a screwdriver bit into the universal bit
holder. Use only screwdriver bits that match the
screw head.
To remove the universal bit holder, pull the locking sleeve 4 toward the rear and remove the universal bit holder 26 out of the tool holder.
Recommendations for Optimal Handling
of the Battery
Protect the battery against moisture and water.
Store the battery only within a temperature
range between 0 °C and 45 °C. As an example,
do not leave the battery in the car in summer.
Occasionally clean the venting slots of the battery using a soft, clean and dry brush.
A significantly reduced working period after
charging indicates that the battery is used and
must be replaced.
Observe the notes for disposal.
Bosch Power Tools
f Before any work on the machine itself
(e.g. maintenance, tool change, etc.) as well
as during transport and storage, remove the
battery from the power tool. There is danger
of injury when unintentionally actuating the
On/Off switch.
f For safe and proper working, always keep
the machine and ventilation slots clean.
f A damaged dust protection cap should be
changed immediately. We recommend having this carried out by an after-sales service.
Clean the tool holder 2 each time after using.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article
number given on the type plate of the machine.
Spare Parts
Auxiliary handle
(without depth stop) . . . . . . . . . 1 612 025 078
After-sales service and customer
assistance
Our after-sales service responds to your questions
concerning maintenance and repair of your product as well as spare parts. Exploded views and information on spare parts can also be found under:
www.bosch-pt.com
Our customer consultants answer your questions
concerning best buy, application and adjustment
of products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
1 619 929 797 | (3.12.07)
26 | English
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: + 61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Transport
The battery is tested according to UN document
ST/SG/AC.10/11/Rev.3 Part III, subsection 38.3.
It has effective protection against internal overpressure and short circuiting as well as devices
for the prevention of violent rupture and dangerous reverse current flow.
The lithium-equivalent content in the battery is
below applicable limit values. Therefore, the battery is not subject to national or international
regulations pertaining to dangerous mediums,
neither as an individual component nor when inserted into a machine. However, the regulations
governing dangerous goods may be relevant
when transporting several batteries. In this case,
it can be necessary to comply with special conditions (e.g., concerning the packaging). For more
information, please refer to the instruction sheet
(in English) under the following Internet address:
http://purchasing.bosch.com/en/start/
Allgemeines/Download/index.htm.
1 619 929 797 | (3.12.07)
Disposal
The machine, accessories and packaging should
be sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into household waste!
According the European Guideline
2002/96/EC for Waste Electrical
and Electronic Equipment and its
implementation into national
right, power tools that are no longer usable
must be collected separately and disposed of in
an environmentally correct manner.
Battery packs/batteries:
Li-ion:
Please observe the instructions in section “Transport”,
page 26.
Do not dispose of battery packs/batteries into
household waste, fire or water. Battery packs/
batteries should be collected, recycled or disposed of in an environmental-friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries
must be recycled according the guideline
91/157/EEC.
Batteries no longer suitable for use can be
directly returned at:
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Subject to change without notice.
Bosch Power Tools