Philips 52PFL9703D/10 Technical data

Register your product and get support at
www.philips.com/welcome
32PFL9603
32PFL9613
37PFL9603
42PFL9603
42PFL9703
42PFL9803
47PFL9603
47PFL9703
52PFL9703
EN LCD television
IT
Televisore LCD
________________________________ ________________________________
DE LCD-Fernsehgerät
ES
Televisor LCD
________________________________ ________________________________
FR
Téléviseur LCD
PT Televisor LCD
________________________________ ________________________________
NL LCD televisie
EL
TËÏÂfiÚ·Û˘ LCD
________________________________ ________________________________
Downloaded From TV-Manual.com Manuals
Downloaded From TV-Manual.com Manuals
1
1.1
1.2
1.3
Important 3
Safety 3
Care of the screen 3
Recycling 3
7
7.1
7.2
7.3
2
2.1
2.2
Your TV 4
Television overview 4
Product highlights 5
7.4
3
3.1
3.2
3.3
3.4
3.5
3.6
Getting started 5
Position the TV 5
Wall mounting - VESA 6
Remote control batteries 7
Antenna cable 7
Power cable 7
First time installation 7
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Use your TV 8
Switch on or off - Standby 8
Watch TV 9
Watch channels from a digital receiver 9
Watch connected devices 9
Watch a DVD 10
Select a Teletext page 10
Change Ambilight mode 11
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
Use more of your TV 12
Remote Control 12
LightGuide brightness 15
TV menus 15
Picture and sound settings 16
Ambilight 19
Teletext 20
Create favourite channel lists 21
Electronic Programme Guide 22
Timers and locks 24
Subtitles 25
Watch and play photos, MP3... 25
Listen to digital radio channels 27
Software update 28
6
6.1
6.2
6.3
6.4
6.5
6.6
Channel installation 30
Automatic channel installation 30
Manual channel installation 31
Rearrange stored channels 32
Channel management 32
Digital reception test 33
Factory settings 33
Table of contents
Downloaded
From TV-Manual.com Manuals
7.5
7.6
7.7
Connections (DVD, receiver, ...) 34
Connections overview 34
About connections 35
Connect your devices with the
Connection assistant 36
Connect your devices without the
Connection assistant 36
Connection setup 42
Preparing for digital services 43
PC network 44
8
Technical data 50
9
Troubleshooting 52
10
Index 54
ENGLISH
Table of contents
UK Digital TV switchover info 56
Remote control setup codes at the end of this
book.
Register your product and get support at
www.philips.com/welcome.
1
2008 © Koninklijke Philips Electronics
N.V. All rights reserved. Specifications
are subject to change without notice.
Trademarks are the property of
Koninklijke Philips Electronics N.V. or
their respective owners.
Philips reserves the right to change
products at any time without being
obliged to adjust earlier supplies
accordingly.
The material in this manual is believed
adequate for the intended use of the
system. If the product, or its individual
modules or procedures, are used for
purposes other than those specified
herein, confirmation of their validity
and suitability must be obtained. Philips
warrants that the material itself does
not infringe any United States patents.
No further warranty is expressed or
implied.
Warranty
No components are user-serviceable.
Do not open or remove covers and
do not insert objects in the ventilation
slots or insert objects not suitable for
the specific connectors. Repairs may
only be done by Philips Service
Centres and official repairshops. Failure
to do so shall void any warranty, stated
or implied.
Any operation expressly prohibited in
this manual, any adjustments, or
assembly procedures not
recommended or authorised in this
manual shall void the warranty.
Pixel characteristics
This LCD product has a high number
of colour pixels. Although it has
effective pixels of 99,999% or more,
black dots or bright points of light
(red, green or blue) may appear
constantly on the screen.This is a
structural property of the display
(within common industry standards)
and is not a malfunction.
Open source software
This television contains open source
software. Philips hereby offers to
deliver or make available, upon
request, for a charge no more than the
cost of physically performing source
distribution, a complete machinereadable copy of the corresponding
source code on a medium customarily
used for software interchange.
This offer is valid for a period of 3
years after the date of purchase of this
product.
To obtain the source code, write to
Philips Innovative Applications N.V.
Ass. to the Development Manager
Pathoekeweg 11
B-8000 Brugge
Belgium
Compliance with EMF
Koninklijke Philips Electronics N.V.
manufactures and sells many products
targeted at consumers, which, like any
electronic apparatus, in general have
the ability to emit and receive
electromagnetic signals.
One of Philips’ leading Business
Principles is to take all necessary
health and safety measures for our
products, to comply with all applicable
legal requirements and to stay well
within the EMF standards applicable at
the time of producing the products.
Philips is committed to develop,
produce and market products that
cause no adverse health effects.
Philips confirms that if its products are
handled properly for their intended
use, they are safe to use according to
scientific evidence available today.
Philips plays an active role in the
development of international EMF and
safety standards, enabling Philips to
anticipate further developments in
standardisation for early integration in
its products.
Mains fuse (UK only)
This TV is fitted with an approved
moulded plug. Should it become
necessary to replace the mains fuse,
this must be replaced with a fuse of
the same value as indicated on the
plug (example 10A).
1. Remove fuse cover and fuse.
2. The replacement fuse must comply
with BS 1362 and have the ASTA
approval mark. If the fuse is lost,
contact your dealer in order to
verify the correct type.
3. Refit the fuse cover.
In order to maintain conformity to the
EMC directive, the mains plug on this
product must not be detached from
the mains cord.
2
Downloaded
From TV-Manual.com Manuals
Copyrights
VESA, FDMI and the VESA
Mounting Compliant logo are
trademarks of the Video Electronics
Standards Association.
Manufactured under license
from Dolby Laboratories. ‘Dolby’, ‘Pro
Logic’ and the double D symbol G,
are trademarks of Dolby Laboratories.
Manufactured under
license from BBE Sound, Inc. Licensed
by BBE, Inc under one or more of the
following US patents: 5510752,
5736897. BBE and BBE symbol are
registered trademarks of BBE Sound
Inc.
Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States
and/or other countries
® Kensington and MicroSaver are
registered US trademarks of ACCO
World Corporation with issued
registrations and pending applications
in other countries throughout the
world.
DLNA®, the DLNA
logo and DNLA Certified™ are
trademarks, service marks, or
certification marks of the Digital Living
Network Alliance.
All other registered and unregistered
trademarks are the property of their
respective owners.
Important
Read this user manual before you start to use this
product.
Pay attention to this section and closely follow the
instructions. The warranty does not apply to
damage caused by not taking into account the
instructions.
1.1
Safety
• To avoid short circuit, do not expose the product
to rain or water.
• To avoid a risk of fire or electric shock do not
place naked flame sources (e.g. lighted candles)
close to the TV.
• Leave a space of at least 10cm (4 inches) all
around the TV for ventilation.
• Keep away from radiators or other heat sources.
• Do not install the TV in a confined space such as
a book case. Make sure that curtains, cupboards
and so on cannot obstruct the air flow through
the ventilation slots.
• To prevent damage, do not insert any object into
the ventilation slots.
• Make sure the TV cannot fall down. Place the TV
on a solid and flat surface and only use the stand
provided with the TV.
• To prevent damaging the mains cord, do not
place the TV, or anything else, on the cord.
Damage the cord may cause a fire or electric
shock.
• When mounted on a swivel stand or VESA wall
bracket avoid force coming on the mains plugs.
Mains plugs that are partly loosened can cause
arcing or fire.
1.2
• Stationary images
Avoid stationary images as much as possible. If
you cannot, reduce screen contrast and
brightness to prevent damage to the screen.
Stationary images are images that remain on the
screen for a long time. Examples of stationary
images are: on screen menus, teletext pages, black
bars, stock market information,TV channel logos,
time displays, and so on.
1.3
Recycling
• Take the packaging to your local recycling centre.
• Dispose old batteries safely according local
regulations.
• This product is designed and manufactured for
material recycling and re-use.
• Do not dispose this product with other
household waste. Inform yourself or ask your
dealer about local environmentally safe recycling
and local regulations. Uncontrolled waste disposal
harms the environment and human health.
(EEC 2002/96/EC)
Care of the screen
• Unplug the TV before cleaning.
• Clean the surface with a soft damp cloth. Do not
apply any other substance (chemical or
household cleaning agent). This may damage the
screen.
• Do not touch, push or rub or strike the screen
with anything hard as this may scratch, mar or
damage the screen permanently.
• To avoid deformations and colour fading, wipe off
water drops as soon as possible.
Important From TV-Manual.com Manuals
Downloaded
3
ENGLISH
1
2
Your TV
This section gives you an overview of the controls
and functions of this TV.
2.1
Television overview
Controls
Remote control
SOURCE
UNIVERSAL MODE
DEMO
1
2
3
4
5
6
7
LightGuide
Indicator light
Remote control sensor
Volume up and down
Menu
Program/Channel up and down
Power switch
Connectors
1 Back connectors
2 Side connectors
For more info see section 7 Connections.
1
2
3
4
5
6
7
8
9
Switch On or switch to Standby
Watch a connected device - DVD, VCR ...
Programme guide
Volume up + or down Ambilight On or Off
Program/Channel up + and down Menu On or Off
Navigation and Rotary key
Colour keys
For more info see section 5.1 Remote control
overview.
4
Downloaded
From TV-Manual.com Manuals
Your TV
Product highlights
Your new TV is equipped with some of the most
modern audio or video innovations.
Your TV offers the following advantages ...
Full High Definition LCD display
A full HD resolution of 1920x1080p, the highest
resolution of HD sources. It offers a brilliant flickerfree progressive scan picture with optimum
brightness and superb colours.
Ambilight
For a more relaxed viewing experience and
improved perceived picture quality.
Perfect Pixel HD
Offers perfect picture quality from any source.
100Hz Clear LCD (if present)
100Hz Clear LCD gives a superior motion
sharpness, better black level,high contrast with a
flicker-free, quiet image and a larger viewing angle.
DVB-T and DVB-C integrated tuner
Next to normal analogue TV broadcast your TV
receives digital terrestrial and in certain countries
also digital cable TV and radio broadcasts.
3
Get started
ENGLISH
2.2
This section helps you with the positioning and the
first time installation of the TV.
3.1
Position the TV
Carefully read the safety precautions in section 1.1
Safety before you position the TV.
• Large screen TVs are heavy. Carry and handle the
TV with at least two persons.
• The ideal distance from which to watch TV is
three times its diagonal screen size.
• Position the TV where light does not fall directly
on the screen.
• Dim lighting conditions in the room for best
Ambilight effect.
• Position the TV 10 to 20cm away from the wall
for the best Ambilight effect.
• Your TV is equipped with a Kensington Security
Slot at the back of the TV for an anti-theft lock
(not supplied).
Electronic Programme Guide - EPG
The EPG shows the scheduled digital TV
programmes on screen. The guide can remind you
when programmes start, switch the TV on, etc.
HDMI connectors
HDMI connectors for highest quality high definition
connectivity.
On 32” and 37” TV models.
USB connection / PC network connection
Multimedia connection for instantly view or play
your photos or music.
Universal remote control
Your TV remote control is a universal remote
control that can operate other devices such as
DVD players and recorders, digital receivers (STB)
or Home Theatre Systems (HTS) of Philips and
many other brands.
On 42”, 47” and 52” TV models.
MPEG4 broadcast (if available)
A higher quality videostandard offered by HD
transmitted broadcasts.
Your TV
Downloaded
From TV-Manual.com Manuals
5
3.2
Wall mounting - VESA
) Caution
Consider the TV’s weight when you wall mount it.
Improper mounting can result in severe injury or
damage. Koninklijke Philips Electronics N.V. bears
no responsibility for improper mounting or
mounting that results in accident or injury.
Your TV is prepared for VESA compliant wall
mounting. This bracket is not included.
You need one of the VESA codes hereunder to
purchase the bracket that fits your TV.
32” /
37” /
42” /
47” /
52” /
81cm
94cm
107cm
119cm
132cm
VESA
VESA
VESA
VESA
VESA
MIS-F
MIS-F
MIS-F
MIS-F
MIS-F
Unmount the TV stand
‡ Locate the four screws of the TV stand.
The 32” / 81cm TV model has two screws.
On a 32” / 81cm TV model.
200, 200, 6
200, 200, 8
300, 300, 8
400, 400, 8
400, 400, 8
Ask your dealer for more info on stands and
wallmount brackets.
The VESA fixation points
Locate the four fixation points at the back of the
TV.
On other screensizes.
® Unscrew the screws.
Two screws on the 32” / 81cm TV model.
On a 32” / 81cm TV model.
Four screws for other TV screensizes.
Ò Lift the TV off the stand.
On other TV screensizes.
6
Downloaded
From TV-Manual.com Manuals
Your TV
Remote control batteries
‡ Open the battery cover on the back of the
remote control.
® Insert the 3 batteries supplied (Type AAALR03-1,5V). Make sure the + and - ends of the
batteries line up correctly (inside of case is
marked.)
Ò Close the cover.
3.5
Power cable
Keep the mains plug at the wall socket accessible at
all time.
The TV is never powered off completely and
consumes energy unless the mains cord is physically
unplugged.
Although this TV has a very low standby power
consumption, unplug the mains cord if you do not
use the TV for a long time to save energy.
‡ Verify that your mains voltage corresponds with
the voltage printed on the sticker at the back of
the TV. Do not insert the mains cord if the
voltage is different.
® Insert the mains cord tightly.
rNote
Remove the batteries if not using the remote
control for an extended period of time.
3.4
Antenna cable
On 32” and 37” TV models.
‡ Locate the antenna connection at the back of
the TV.
® Insert the antenna cable tightly into the
Antenna x socket.
On 42”, 47” and 52” TV models.
On 42PFL9803,
Your TV
Downloaded
From TV-Manual.com Manuals
7
ENGLISH
3.3
4
Use your TV
Learn how to operate your TV for daily use.
4.1
Turn on or off - Standby
rNote
The TV may take up to 15 seconds to turn on.
To turn on the TV:
• Press B Power at the right of the TV if the
standby indicator is off.
• Press B on the remote control if the standby
indicator is on.
The LightGuide flashes during start up and turns
on completely when the TV is ready for use.
To switch to standby:
• Press B on the remote control.
The LightGuide turns off and the standby
indicator is on.
To turn off:
• Press B Power at the side of the TV.
Both the LightGuide and the standby indicator
turn off.
SOURCE
UNIVERSAL MODE
TELETEXT
SUBTITLE
DEMO
8
Downloaded
From TV-Manual.com Manuals
Use your TV
Watch TV
4.3
4.2.1 Switch channels
‡ To switch TV channels:
• Press a number (1 to 999) or press P+ or Pon your remote control.
• Press Program/Channel - or + on the side
controls of the TV.
® Press R to return to the previously viewed TV
channel or connected device.
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
Watch channels from a
digital receiver
ENGLISH
4.2
‡ Switch on the digital receiver.
The picture from your receiver automatically
appears on the screen.
® Use the remote control of your digital receiver
to select TV channels.
If the picture does not appear:
‡ Press the Source v key.
® Press o or œ to select where you connected
your digital receiver.
Ò Press OK.
SOURCE
SOURCE
UNIVERSAL MODE
CLOCK
TELETEXT
SUBTITLE
DEMO
4.2.2 Adjust volume
‡ To adjust the volume:
• Press V + or - on the remote control
• Press Volume + or - on the side controls
of your TV.
® To mute the sound:
• Press ¬.
• Press ¬ again to restore the sound.
rNote
When you did not connect your devices yet, go to
section 7 Connections.
4.4
Watch connected devices
‡ Switch on the device.
The picture from your device automatically
appears on the screen.
If the picture does not appear:
® Press the Source v key.
Ò Press o or œ to select where you connected
your device.
† Press OK.
ABC
DEF
Use your TVFrom TV-Manual.com Manuals
Downloaded
rNote
When you did not connect your devices yet, go to
section 7 Connections.
9
4.5
Watch a DVD
4.6
‡ Switch on your DVD player.
® Insert a DVD disc in your player.
The DVD picture automatically appears on the
screen.
Ò Press Play πon the DVD player.
If the picture does not appear:
‡ Press the Source v key.
® Press o or œ to select where you connected
your DVD player.
Ò Press OK.
Wait a few seconds until the picture appears.
† Press Play π.
Select a Teletext page
Most TV channels broadcast information through
Teletext.
To watch Teletext:
‡ Press Teletext.
The main index page appears.
® To select a page of your choice:
• Enter the page number with the number keys.
• Press P- or P+ or o or œ or the g key to
view the next or the previous page.
• Press a colour key to select one of the colour
coded items at the bottom of the screen.
• Press R to return to the previously viewed
page.
Ò Press Teletext again to switch Teletext off.
SOURCE
SOURCE
UNIVERSAL MODE
SOURCE
UNIVERSAL MODE
TELETEXT
TELETEXT
SUBTITLE
DEMO
TELETEXT
SUBTITLE
DEMO
rNote
Only for UK: some digital TV channels offer
dedicated digital text services (for example BBC1).
For more information on teletext, see section 5.6
Teletext.
10
Downloaded
From TV-Manual.com Manuals
Use your TV
Change Ambilight mode
ENGLISH
4.7
You can adjust the speed at which Ambilight
responds to the on-screen images.
Adjust the Ambilight mode:
‡ Press Ambilight to switch on.
® Press Mode to adjust Ambilight between a
relaxed and a dynamic setting.
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
CLOCK
The Mode settings are only available if Ambilight
colour is set to Active mode in the Ambilight menu.
When a fixed colour has been selected the Mode
key has no function. See section 5.5 Ambilight.
LoungeLight mode (if available)
When the TV is in standby, you can switch
Ambilight on.
‡ Press Ambilight. Wait until Ambilight lights up.
® Press Mode repeatedly to toggle through the
available Ambilight effects.
For more information on Ambilight, see section 5.5
Ambilight.
à Tip
Dim lighting conditions in the room for best
Ambilight effect.
Use your TVFrom TV-Manual.com Manuals
Downloaded
11
5
Use more of your TV
This section helps you perform advanced TV
operations including how to:
• use the menus
• adjust picture, sound and Ambilight settings
• make use of Teletext
• create favourite channel lists
5.1
Remote control
5.1.1
Remote control overview
•
•
•
•
make advantage of Electronic Programme Guide
set locks and timers
set subtitles and select a subtitle language
view your photos or play your favourite music
from a USB memory device or from your PC or
Home network.
1
Standby B
To switch the TV on or back to standby.
Source v
• To switch the Source menu on or off.
• To select a connected device or to return to
TV.
TV
Sets the remote control in TV mode.
Teletext
To switch teletext on or off.
Colour keys
• Easy selection of teletext pages.
• Easy selection of tasks.
Demo
To switch the Demo menu on and to get a
demonstration of the features of the TV.
Guide a
To switch on or off the Electronic Programme
Guide.
Navigation and rotary key
To navigate (o, œ, p, π) or turn left or right
to go through lists or settings.
2
3
DEMO
4
5
6
7
8
OK
• To display the channel list.
• To activate a setting.
9 Back key g
To select the previous programme or the
previous TXT page.
To remove the channel list.
10 Audio and video keys Ò,π/º,†,‡,®
To operate a DVD player or recorder, Blu-ray
Disc player or VCR.
Cancel (only for UK)
To cancel only Digital text or Interactive
services.
11 Volume V
To adjust the volume.
12 Mute ¬
To mute the sound or restore it.
12
Downloaded
From TV-Manual.com Manuals
Use more of your TV
See section 10 Index to find the section in the
manual about a specific remote control key.
5.1.2 Universal remote control
Your TV remote control is a universal remote
control that can operate other devices such as
DVD players and recorders, digital receivers (Settop boxes – STB) or Home Theatre Systems (HTS)
of Philips and many other brands.
‡ Press DVD, STB or HTS to select a DVD, a
cable receiver (STB) or a Home Theatre (HTS)
device. The key blinks as long as you are in this
control.
UNIVERSAL MODE
SOURCE
UNIVERSAL MODE
TELETEXT
SUBTITLE
DEMO
® Use the relevant keys on the TV remote control
to operate the device.
If the device does not react or operates
incorrectly, you need to set up your remote
control for your particular device.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
See section 5.1.3 Set to operate a particular
device.
Ò Press the TV key to return to normal TV mode.
When no key is pressed for 30 seconds the
remote control switches back to normal TV.
5.1.3 Set to operate a particular device
You can choose from three ways to programme the
remote control for a device of a particular brand.
You can:
- use the Universal remote control assistant to
help you
- enter a brand's setup code or
- start an auto search.
rNote
Possibly the remote control is not compatible with
all types of DVD, cable receivers and Home Theatre
Systems.
Method 1: Use the Universal remote control
assistant
‡ Turn on your device.
® Press the DVD, STB or HTS universal mode key
for 4 seconds to select the universal mode you
need or press Menu Ï and select Setup >
Installation > Remote control assistant and
press π to enter.
- DVD stands for DVD, DVD-R, HDD and Bluray Disc
- STB stands for digital receiver and set-topboxes (cable, satellite)
- HTS for Home Theatre Systems, Audio/Video
systems
The remote control is now in the selected
programming mode. Follow the instructions on
screen.
rNote
Ensure that the TV and the device are within reach
of the remote control.
Method 2: Enter the setup code directly
Instead of using the Universal remote control
assistant, you can also enter a setup code directly.
Find a list of these codes per brand and device at
the end of this manual.
‡ Press the DVD, STB or HTS key and OK at the
same time for 4 seconds to select the universal
mode you need.
® Enter the three-number code for the type and
brand of your device. Some brands have several
setup codes available and you need to select
the known one. You can try them one by one.
13
ENGLISH
13 Number keys
To select a TV channel.
14 Clock
To display the time on screen.
15 Ambilight
To switch Ambilight on or off.
16 Mode
To adjust the dynamic effect of Ambilight
17 Previous channel R
To return to the previously viewed channel
18 +P- Channel up or down
To switch to the next or previous channel in
the channel list.
19 Menu Ï
To switch the menu on or off
20 On screen information i
To show channel or programme information if
available.
21 Dual screen b
To show teletext on the right and the picture
on the left of the screen.
22 Subtitle
To activate or deactivate the subtitle mode.
23 Widescreen Picture format q
To select a picture format.
24 DVD STB HTS
To control connected devices.
If you entered a known code, all universal mode
keys will blink to confirm the selection. If you
entered an unknown code, all universal mode
keys will light up for 2 seconds. Repeat Step 2
with a different code.
Ò Point the remote control at the device, and
press B to test if the code is known for your
device.
If successful try whether you can operate all
functions. If not successful, or if you cannot
operate all functions, repeat Step 1 and 2 with
one of the other setup codes for your brand.
Method 3: Automatic search of all codes
If you are not successful to find the known brand
or code, try an automatic search of all codes. The
automatic search can take several minutes.
If after the automatic search no code is successful, it
is not possible to operate your particular device
with the remote control. In such case, use the
device's own remote control.
‡ Turn on the device you want the TV remote
control to set up for.
®. Point the remote control to the device during
the automatic search.
Ò To select the universal mode you need, press
the DVD, STB or HTS key and the OK key at
the same time for 4 seconds.
The selected universal mode lights up
constantly.
† Press OK to start the automatic search.
Every two seconds, when a new code is sent,
the B key will blink.
Keep pointing the remote control to the device.
º When the device switches off, press OK to
stop the search.
◊Press B to switch on your device.
‹ Press the remote control keys to try if you can
operate all functions. If you cannot operate all
functions, press OK again to continue the
automatic search for a correct code.
≈If you can operate all functions, press the
currently selected universal mode key to
confirm and to quit the automatic search.
5.1.4
Keep the remote control in the
chosen universal mode permanently
If you press the DVD, STB or HTS key the remote
control can operate other devices. When no key is
pressed for 30 seconds the remote control
switches back to normal TV.
You can set the remote control to hold a universal
mode as long as no other universal mode is
pressed. This disables the 30 seconds switch back to
normal TV.
‡ Press the TV key.
® Press OK and ¬ at the same time for 4
seconds. The B key lights up for 2 seconds.
From now on the remote control will not switch
back to normal TV mode.
To return to the 30 seconds switch back to
normal TV mode, follow the same steps 1 and 2.
5.1.5 Device functions overview
When the remote control is set for a particular
device all keys have the same function except the
keys mentioned here.
• DVD player
Menu key = DVD Disc menu
P+/- = DVD Next/Previous track
• DVD Recorder
Ò key = DVD-R previous track
† key = DVD-R next track
• DVD recorder with Hard Disc Drive
Menu key = DVD-R HDD browser
Ò key = DVD-R HDD previous track
† key = DVD-R HDD next track
• Blu-ray Disc player
a key = BD Content menu
Menu key = BD Disc menu
rNote:
To pause the automatic search, press OK. Press o
or œ to search for the codes one by one backward
or forward to locate the known code for your
device or press OK again to continue the
automatic search.
14
Downloaded
From TV-Manual.com Manuals
Use more of your TV
5.3
5.1.6 Remote control setup codes
See the end of this manual.
5.3.1 The menu
‡ Press Menu Ï to show the TV menu.
® Press Menu Ï to quit the TV menu.
5.2
TV menus
ENGLISH
• Digital or Satellite receiver
No change of functions.
• Home Theatre System
Menu key = HTS Disc menu
V key = HTS volume
P+/- = HTS Next/Previous
With the on screen menus you install your TV,
adjust picture, sound and Ambilight settings and
access features. This section gives an overview of
the menus and describes how to navigate.
LightGuide brightness
The LightGuide at the front of the TV indicates the
start up of the TV.
After start up the LightGuide is lit constantly. You
can set the light intensity or let it switch off after
start up.
‡ Press Menu Ï > Setup > Installation >
Preferences > LightGuide brightness.
® Press π to enter the list.
Ò Press o or œ to select the brightness level
from 0 (off) to 4.
The TV menu offers the following items:
TV menu
Smart settings
Picture
Sound
Ambilight
Settings assistant
Features
Setup
• Smart settings
Select this item to set the TV to one of the
predefined settings. Each setting combines
picture, sound and Ambilight.
• Picture
Select this menu item to adjust all picture
settings.
• Sound
Select this menu item to adjust all sound settings.
• Ambilight
Select this menu item to adjust all Ambilight
settings.
• Settings assistant
Use the Settings assistant to guide you through
basic picture, sound and Ambilight settings in an
easy way.
• Features
Select this item for other feature settings.
• Setup
Select this item
- for installation and to update the TV software;
- to make use of the Remote control assistant
which will help you to setup your remote
control to operate other devices;
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
15
- to use the connection assistant which will help
you to connect your devices to the TV.
5.3.2 Use of the menu
Learn to use the menus with this example.
‡ Press Menu Ï.
The TV menu appears on the screen.
◊Press o or œ to adjust the setting.
‹Press p to return to the Picture settings or
press Menu Ï to quit the TV menu.
rNote:
More choices come available when digital channels
are installed and broadcasted.
5.4
TV menu
Smart settings
Picture
Picture and Sound settings
The first time you switched on the TV you have
selected your preferred settings for picture, sound
and Ambilight. The following sections describe how
to modify or read just those settings.
Sound
Ambilight
Settings assistant
Features
Setup
® Press o or œ to select Picture.
ÒPress π to enter the picture settings.
Picture
Contrast
Contrast
Brightness
90
47
Colour
Hue
52
0
Sharpness
4
5.4.1 Smart settings
Sets the TV to one of the predefined settings. Each
setting combines picture, sound and Ambilight.
‡ Press Menu Ï and select Smart settings.
® Press π to enter the list.
Ò Press o or œ to select a setting.
† Press OK.
º Press Menu Ï to quit the TV menu.
Smart settings: Personal, Vivid, Standard, Movie,
Energy saving, Game.
Noise reduction
Tint
...
† Press œ to select Brightness.
Picture
Brightness
Contrast
Brightness
98
47
Colour
Hue
52
0
Sharpness
4
Noise reduction
5.4.2 Settings assistant
Use the Settings assistant to guide you through
basic picture and sound settings in an easy way.
‡ Press Menu Ï, select Follow the instructions
on screen.
® Select Settings assistant and press π to enter.
Ò Press the green key to start the assistant.
† Press p or π to select the left or right side to
make your choice.
º When finished, press the green key to store all
your settings.
Tint
...
º Press π to enter the brightness setting.
Brightness
16
Downloaded
From TV-Manual.com Manuals
Use more of your TV
TV menu
Picture
Smart settings
Picture
Contrast
Brightness
Sound
Colour
Ambilight
Hue
Sharpness
Features
Noise reduction
Setup
Tint
Perfect Pixel HD
Active control
Light sensor
Picture format
Auto format mode
• Contrast
Changes the level of bright parts in the picture
but keeps the dark parts unchanged.
• Brightness
Changes the level of light of the total picture.
• Colour
Changes the level of saturation.
• Hue
If NTSC is broadcasted, this level compensates
the colour variations.
• Sharpness
Changes the level of sharpness of fine details.
• Noise reduction
Filters out and reduces the noise in the picture.
Set the level to Minimum, Medium, Maximum or
Off.
• Tint
Sets the colours to Normal, Warm (reddish) or
Cool (bluish). Select Custom to make a setting of
your own in the Custom menu.
• Custom
Press the green key to select each bar to
change the value of:
- R-WP red whitepoint
- G-WP green whitepoint
- B-WP blue whitepoint
- R-BL red blacklevel
- G-BL green blacklevel
• Perfect Pixel HD
Controls the advanced settings of the Perfect
Pixel HD Engine, resulting in best sharpness,
contrast, colour and motion.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
Picture
Perfect Pixel HD
...
Noise reduction
HD Natural Motion
Tint
100 Hz Clear LCD
Advanced sharpn...
Perfect Pixel HD
Dynamic contrast
ENGLISH
5.4.3 Picture settings
This section describes how to adjust all picture
settings individually.
‡ Press Menu Ï.
® Select Picture and press π to enter the list.
Ò Press o or œ to select a setting.
Active control
Light sensor
MPEG artefact red...
Picture format
Colour enhance...
Auto format mode
- HD Natural Motion
Removes motion judder and reproduces
smooth movement especially in movies.
- 100 Hz Clear LCD (if present)
Gives a superior motion sharpness, better black
level, high contrast with a flicker-free, quiet
image and a larger viewing angle.
- Advanced sharpness
Enables superior sharpness, especially on lines
and contours in the picture.
- Dynamic contrast
Sets the level at which the TV automatically
enhances the details in dark, middle and light
areas of the picture.
- Dynamic backlight
Sets the level at which power consumption can
be reduced by dimming the brightness intensity
of the screen.
Choose for the best power consumption or for
the picture with the best brightness intensity.
- MPEG artefact reduction
Smooths the digital transitions in the picture.
- Colour enhancement
Makes the colours more vivid and improves the
resolution of details in bright colours
• Active control
Corrects all incoming signals in order to provide
the best picture possible.
Switches Active control on or off.
• Light sensor
Adjusts the picture and Ambilight settings on the
lighting conditions of the room. Switches Light
sensor on or off.
• Picture format / Auto format mode
See section 5.4.4 Widescreen picture format.
17
5.4.4 Widescreen picture format
Avoid black bars on the sides or on top and
bottom of the picture. Change the picture format
to a format that fills the screen.
‡ Press q to switch on the Picture format
menu.
UNIVERSAL MODE
TELETEXT
SUBTITLE
DEMO
® Press o or œ to select an available picture
format.
Ò Press OK.
† Press o to shift the picture upwards if subtitles
are hidden.
à Tip
For minimal distortion, select the Auto format
setting.
• Auto format (Not for PC.)
Enlarges the picture automatically to fill the
screen. Subtitles remain visible. You can set Auto
format in two different modes.
‡ In the TV menu, select Picture > Auto format
mode.
® Select Auto-fill to fill the
screen as much as
possible. Select Autozoom to keep the original
picture format but black
bars may be visible.
• Super zoom (Not for HD.)
Removes the black bars on
the side of 4:3 broadcasts.
There is a minimal
distortion.
• 4:3 (Not for HD.)
Shows the classical 4:3
format.
• Movie expand 14:9
(Not for HD.)
Scales the format to 14:9.
18
Downloaded
From TV-Manual.com Manuals
• Movie expand 16:9
(Not for HD.)
Scales the format to 16:9.
• Wide screen
Stretches the format to
16:9.
• Unscaled
(Only for HD and PC.)
Maximum sharpness.
Distortion may appear on
borders. Black bars may
appear with pictures from
your PC.
rNote
Do not forget to name the connection in the
Connection menu. See section 7.5.1 Naming your
devices.
5.4.5 Sound settings
This section describes how to adjust all sound
settings.
‡ Press Menu Ï and select Sound.
® Press π to enter the list.
Ò Press o or œ to select a setting.
TV menu
Sound
Smart settings
Picture
Equalizer
Volume
Sound
Volume - Visually...
Ambilight
Balance
Audio language
Features
Dual I/II
Setup
Mono/Stereo
TV speakers
Surround mode
Headphone volume
Auto volume level...
Delta volume
Auto surround
• Equalizer
Changes the bass and treble of the sound. Select
each bar to change the setting.
• Volume
Changes the volume. When adjusting the volume
with V a volume bar appears. If you do not
want it to appear go to Menu > Setup >
Installation > Preferences and press π to enter
the list and select Volume bar off.
Use more of your TV
5.5
Ambilight
ENGLISH
• Volume – Visually impaired (UK only)
Changes the volume of the selected Visually
impaired audio language in the Setup, Installation
menu. See section 6.1 Automatic installation.
• Balance
Sets the balance of the left and right
loudspeakers to fit best your listening position.
• Audio language
A list of audio languages for the current
programme may be available when digital
channels are installed and broadcasted.
To permanently change the audio language, see
section 6 Channel installation.
• Dual I/II
If broadcasted, you can choose between two
different languages.
• Mono/stereo
If stereo broadcasting is available, you can select
Mono or Stereo per TV channel.
• TV speakers
If you have connected an audio system to your
TV, you can switch off the TV speakers.
If your audio system supports Easylink, see
section 7.2.2 Easylink.
Select Automatic to have the sound from your
TV automatically reproduced by your audio
system.
• Surround mode
To select a more spatial sound if broadcasted or
if available from a connected device.
• Headphone volume
Changes the volume of the headphone.
You can mute the TV speakers with ¬ on the
remote control.
• Auto volume levelling
Reduces sudden volume differences like at the
beginning of commercials or when switching from
one channel to another.
Select on or off.
• Delta volume
Levels out volume differences between channels
or connected devices.
‡ Switch to the channel or device you want to
level out the volume difference.
® Select Delta volume in the Sound menu and
change the volume level.
• Auto surround
Switches the TV automatically to the best
surround sound mode dependant on the
broadcast.
Select on or off.
You can adjust Ambilight settings.
‡ Press Menu Ï and select Ambilight.
® Press π to enter the list.
Ò Press o or œ to select a setting.
TV menu
Ambilight
Smart settings
Ambilight
Active mode
Picture
Sound
Ambilight
Brightness
Colour
Separation
Features
Setup
• Ambilight
Switches Ambilight on or off.
• Active mode
Adjusts the speed at which Ambilight responds to
the on-screen images..
Only available when Active mode has been
selected in the Ambilight colour menu.
Relaxed sets Ambilight to change soft and
smoothly with the images on screen.
Dynamic sets Ambilight to change quick and
responsive.
• Brightness
Changes the light output of Ambilight.
• Colour
Sets the Ambilight colour to either dynamic
behaviour (Active mode) or one of the
predefined Ambilight fixed colours.
Custom allows fine tuning of a fixed colour.
Ambilight
Colour
Ambilight
Active mode
Warm white
Active mode
Brightness
Colour
Separation
Cool white
Blue
Custom
• Separation
Sets the difference in colour level between the
Ambilights at the sides of the TV.
Separation off gives a dynamic but uniform
colour Ambilight.
ç Caution
To avoid bad infrared remote control reception,
place your devices out of sight of Ambilight.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
19
5.6
Teletext
5.6.4
Your TV has a 1200 pages memory that stores
broadcasted teletext pages and subpages to reduce
waiting time.
To select a teletext page see section 4.6 Select a
Teletext page.
5.6.1 Select a teletext language
Some digital TV broadcasters offer the possibility to
select your preferred teletext language. See section
6.1 Automatic installation.
5.6.2 Select pagenumber subpages
A teletext page number can hold several subpages.
The pages are shown on a bar next to the main
pagenumber.
‡ Press Teletext.
® Select a teletext page.
Ò Press p or π to select a subpage.
SOURCE
UNIVERSAL MODE
TELETEXT
TELETEXT
SUBTITLE
DEMO
5.6.3 Select T.O.P. teletext broadcasts
T.O.P. teletext (Table of Pages) is not broadcast by
all TV channels. You can easily jump from one
subject to another without using pagenumbers.
‡ Press Teletext.
® Press i.
The T.O.P. overview appears.
Ò Use p or π, o or œ to select a subject.
† Press OK to view the page.
Dual screen teletext (not available for
channels with Digital Text services)
View the TV channel and teletext next to each
other.
‡ Press b for Dual screen teletext.
® Press Teletext again to show normal teletext.
Ò Press Teletext to switch off teletext.
5.6.5
Search teletext
Quickly jump to a subject linked to a series of
pagenumbers or search for specific words in
teletext pages.
‡ Press Teletext.
® Press OK to highlight the first word or number.
Ò Press p or π, o or œ to jump to the next
word or number on the page.
† Press OK to search a page which holds the
highlighted word or number.
º Press o until no word or number is highlighted
to quit Search.
5.6.6 Enlarge teletext pages
For a more comfortable reading, you can enlarge
the teletext page.
‡ Press Teletext and select a teletext page.
® Press q to enlarge the top part of the page.
Ò Press q again to view the enlarged lower
part of the page.
† Press o or œ to scroll through the enlarged
page.
º Press q again to return to the normal page
size.
UNIVERSAL MODE
TELETEXT
SUBTITLE
DEMO
UNIVERSAL MODE
TELETEXT
SUBTITLE
DEMO
20
Downloaded
From TV-Manual.com Manuals
5.6.7 Teletext menu
With the options in the teletext menu you can
reveal hidden info, let cycle subpages automatically
and change the character setting.
• Reveal
Hide or unhide hidden information on a page,
such as solutions to riddles or puzzles.
• Cycle subpages
If subpages are available for the selected page,
you can make subpages cycle automatically.
Use more of your TV
5.7
Create favourite channel
lists
ENGLISH
• Language
Some languages use a different set of characters.
Switch to the other group to show the text
correctly.
‡ Press Teletext.
® Press Menu Ï.
View the All channels list or set up a Favourite list
of your own with your preferred TV channels and
radio stations.
Teletext menu
Reveal
Off
Cycle subpages
Off
Language
Gr. II
Ò Press o or œ to select an option.
† Press OK to change a setting.
º Press Menu Ï to quit the teletext menu.
◊Press Teletext to switch off teletext.
5.7.1 Select a favourite list
You can select one of the favourite channel lists.
‡ Press OK.
The first time after you have finished the
installation, the All channels list is shown. In
other situations, it brings up the last selected
favourite list.
All channels
5.6.8
....
EXT 3
Digital text services (UK only)
Some digital TV broadcasters offer dedicated digital
text or interactive services (for example BBC1) on
their digital TV channels. These services work as
normal Teletext with the number, colour and
navigation keys to select and navigate.
‡ Press Teletext.
® Press p or π, o or œ to select or highlight
items.
Ò Press one of the colour keys to select an
option.
† Press OK to confirm or activate.
º Press ‡ Cancel to cancel Digital text or
interactive services.
ç Caution
Digital text services are blocked when subtitles are
broadcasted and Subtitle On is set in the Features
menu. See section 5.10 Subtitles.
5.6.9 Teletext 2.5
If broadcasted by the TV channel this teletext offers
more colours and better graphics.
Teletext 2.5 is switched on as a factory setting.
‡ Press Menu Ï on the remote control and
select Setup > Installation > Preferences >
Teletext 2.5 and press π to enter the list.
® Select on or off.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
A
1 Analogue channel 1
2 Digital channel 1
3 Digital channel 2
4 Radio channel 1
....
Select list
® Press the red key to show all favourite lists.
Ò Press o or œ to select a list.
† Press OK.
The selected favourite list appears.
º Press OK again to quit.
5.7.2 To set up a favourite list
Create or modify your own favourite list.
‡ Press OK.
The last selected list appears.
® Press the red key to show all favourite lists.
Ò Press o or œ to select a list.
† Press OK.
º Press the green key to enter the Edit mode.
The selected list brings up a full channel list.
◊Press o or œ to highlight a channel.
‹ Press OK to mark (or unmark) the highlighted
channel. The channel is added to (or removed
from) the selected list.
≈Press the green key again to leave the Edit
mode.
The modified channel list appears again.
21
5.7.3 Select a channel from a favourite list
‡ Press OK.
The last selected channel list appears.
® Use o or œ to highlight a channel.
Ò Press OK.
The TV tunes to that channel.
à Tip
• Use -P+ to go through the TV channels of the
selected favourite list.
• With the number keys you can still select
channels which are not marked as favourite.
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
-
5.8
Electronic Programme
Guide - EPG -
The Electronic Programme guide is an on screen
guide to scheduled digital TV programmes.
You can navigate, select and view programmes by
time, title or genre. There are two types of EPG,
‘Now and Next’ and ‘7 or 8 day’ EPG.
When digital channels are installed and
broadcasted, EPG is available. ‘Now and Next’ is
always available but the ‘7 or 8 day’ EPG is only
available in some countries.
With the EPG menu you can...
• see a list of current broadcasted programmes
• see the next programme
• group programmes by genre
• set reminders when programmes will start
• set up preferred EPG channels
• etc.
CLOCK
5.8.1 Switch on EPG
‡ Press a.
UNIVERSAL MODE
TELETEXT
SUBTITLE
DEMO
The following type of EPG appears:
‘Now and Next’ EPG
Detailed information about the current programme
is shown.
26 BBC1
Tue., 12 Sep
09:17
Title : Commonwealth Games
Info: 7:50 - 12:30 : 280 min
..........
Exit
Next
Press -P+ to change channel.
Or
‘7 or 8 day’ EPG
It may take some time to receive the EPG data.
The list of TV programmes will show.
22
Downloaded
From TV-Manual.com Manuals
Use more of your TV
Tue., 12 Sep
Around
09:55
Next
BBC ONE
07:50 Commonwealth
12:30 Commonwealth
BBC TWO
09:50 Tweenies
10:15 Something Special
five
09:00 The Wright Stuff
10:30 Trisha Goddard
BBC THREE 05:32 This is BBC THREE
BBC FOUR
05:32 This is BBC FOUR
abc1
09:20 Moonlighting
Remind
Watch
13:50 Anastasia
ENGLISH
Programme guide
12:00 This is BBC THREE
12:00 This is BBC FOUR
10:15 Daddio
Jump to ...
Info
0010 - EEN
® Use the colour keys to activate the available
actions at the bottom of the screen.
• Next: to show information about the next
programme.
• Remind: to mark or unmark a programme as a
reminder.
• Watch: to watch or listen to a current
programme.
• Jump to...: to jump to the next or previous day.
• Info: to display information on a selected
programme (if available).
Ò Press a to quit the EPG.
5.8.2
More on ‘7 or 8 day’ EPG
Search by genre, scheduled reminders, etc. are
managed in the Programme guide menu.
‡ Press a on the remote control.
® Press Menu Ï.
The Programme guide menu appears.
Programme guide
What's on
What's on
12:30 South Today
11:50 Working Lunch
Search by genre
Scheduled remind... 11:55 Melrose Place
Preferred EPG ch... 13:00 In aller Freund
Acquire EPG data
Ò Press o or œ to select a menu option.
† Press π to enter.
º Press o or œ to make a selection.
◊Press OK to activate or press the green key to
watch
‹ Press a to quit the EPG.
rNote
Only channels marked as Preferred EPG channels
appear in the Programme guide menu.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
23
5.9
Timers and locks
This section describes how to switch the TV on or
off at a specified time and to lock or unlock the TV.
5.9.1 Automatically switch to standby
Sleeptimer switches the TV to standby after a time.
‡ Press Menu Ï on the remote control and
select Features > Sleeptimer and press π to
enter the sleeptimer bar.
® Press o or œ to set the time up to 180
minutes in steps of 5 minutes. If set to 0
minutes, the Sleeptimer is switched off.
You can always switch off your TV earlier or reset
the time during countdown.
5.9.2 Automatically switch the TV on
On timer switches the TV on automatically to a
specified channel at a specified time, from standby.
‡ Press Menu Ï on the remote control and
select Features > On timer and press π to
enter the On timer menu.
® Use p or π, o or œ to select and enter the
menu items one by one to set a channel, a day
of the week or daily, and a starting time.
Ò Press OK to confirm.
† Press Menu Ï to quit the menu.
à Tip
To switch off the On timer, select Off in the On
timer menu.
5.9.3 Lock TV channels and programmes
Lock TV channels and/or programmes from
connected devices to prevent children from
watching them. Lock and unlock with a four number
code.
Set or change your code
‡ Press Menu Ï on the remote control and
select Features > Set or Change code and press
π to enter your code.
® Enter your code with the number keys.
The Features menu reappears with a message
confirming that your code has been created or
changed.
Did you forget your code ?
‡ Select Change code.
® Press π.
24
Downloaded
From TV-Manual.com Manuals
Ò Enter the overriding code 8-8-8-8.
† Enter a new personal code.
º Confirm your new entered code.
The previous code is erased and the new code
is stored.
5.9.4 Activate or deactivate Child lock
Set your code and you can:
• Lock all channels and devices,
• Lock specific channels and devices,
• Set a time after which all channels and devices
are locked,
• Set the maximum allowed parental rating for
digital channels that are installed and broadcast.
‡ Press Menu Ï.
® Select Features > Child lock and press π.
Ò Enter your code with the number keys.
† Select one of the options.
º Press π.
Lock or unlock all channels and connected devices
‡ Select Lock or Unlock.
Lock a certain programme or all channels from a
certain time
Child lock
Custom lock
Lock
Custom lock
Lock after
Channel lock
Unlock
Parental rating
‡ Select Custom lock.
® Press π to enter the Custom lock menu.
Ò Press π again to enter the Lock after menu.
† Select On to switch on the Timer lock.
º Press p.
◊Select Time.
‹ Press π.
≈Enter the time with o or œ and π.
Ú Press OK.
Lock one or more channels and connected devices
‡ Select Custom lock.
® Press π to enter.
Ò Press o or œ to select Channel lock.
† Press π.
º Press o or œ to select the channel(s) you
want to lock or unlock.
◊Each time press OK to lock or unlock the
channel.
Use more of your TV
5.10.3 Select a digital subtitle language
If subtitle broadcasting is available with digital
channels, you can select a preferred subtitle
language out of a list of broadcasted languages. The
preferred subtitle languages set in the Installation
menu are overruled temporarily.
‡ Press Menu Ï on the remote control and
select Features > Subtitle language and press π
to enter the list of available languages.
® Press o or œ to select a subtitle language.
Ò Press OK.
5.10 Subtitles
5.11 Watch and play your
photos and music
For each TV channel, subtitles can be set, coming
from Teletext or DVB-T (digital) broadcasts.
If digital channels are installed and broadcasted, you
can select your preferred subtitle language.
5.10.1 Subtitling from analogue TV channels
‡ Select an analogue TV channel.
® Press Teletext to switch on Teletext.
Ò Enter the three number pagenumber of the
subtitle page.
† Press Teletext to switch off Teletext.
rNote
The Teletext subtitle page of analogue channels
must be stored for each TV channel separately.
5.10.2 Activate or deactivate subtitling
‡ Press Menu Ï on the remote control and
select Features > Subtitle and press π to enter
the list.
® Press o or œ to select On to show the
subtitles always or On during mute to show the
subtitles only when the sound is muted with the
¬ key on the remote control.
Ò Press p to return to the Features menu.
TV menu
Features
Smart settings
Common interface
Subtitle
Picture
Sound
Ambilight
Subtitle language
Watch pictures or listen to music stored on a USB
device (not supplied with the TV), a camcorder
(only for photos) or from your PC network. Watch
your pictures as a slideshow or listen to a self made
music playlist.
rNote
Philips is not responsible if your USB device is not
supported nor shall Philips accept any liability for
damage or loss of stored data.
5.11.1 Insert the USB device
‡ Insert a device at the side of the TV while the
TV is switched on.
A message appears that a USB device has been
detected.
rNote
In case the USB device does not automatically
break in, press Source v > USB/Memory devices
and press OK.
Select Side and press OK to display your
camcorder content.
5.11.2 Remove the USB device
‡ Press Source v.
® Remove the USB device.
Ò Select TV or another connected device to
watch a programme.
Sleeptimer
Child lock
Features
Set/Change code
Setup
On timer
Demo
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
25
ENGLISH
Set an age rating to a digital programme
Some digital broadcasters have their programmes
rated (depending on your country). When the
rating is higher than your child’s age, the
programme will be locked.
‡ Select Custom lock.
® Press π to enter.
Ò Press o or œ to select Parental rating.
† Press π.
º Press o or œ to select an age rating.
◊Press Menu Ï to quit the Child lock menu.
5.11.3 Watch your pictures, start a
slideshow and play music
Look up your pictures in the Picture album of your
USB device.
‡ Select the Picture folder for the picture files you
have stored on your USB device.
Afrika_2001
Paris_2006
My_car.jpg
Jean.jpg
Mary.jpg
® Press π to enter the Picture folder.
Ò Press o or œ to select a picture or a picture
album.
Picture
Afrika_2001
Afrika_2001
Paris_2005
My_car.jpg
Jean.jpg
Kenya.jpg
Congo.jpg
Victoria.jpg
Mary.jpg
Cairo.jpg
Afrika_2001
USB
Afrika_2001
Kenya.jpg
Kenya.jpg
Afrika_2001
Kenya.jpg
Congo.jpg
Victoria.jpg
Dakar.jpg
Thumbnails
Watch the pictures of a selected album in an
overview.
‡ Select a picture album.
® Press π to enter the picture list.
Ò Press the blue key.
† Press o or œ, p or π to highlight a picture.
º Press OK to watch the picture.
◊Press p to return to the thumbnail overview.
‹ Press the blue key again to go back to the
picture list.
—
Picture
Music
Picture
—
USB
• Slide time
Sets the time lag for the picture transitions:
Short, Medium or Long.
• Rotate
To rotate a picture.
• Start/Show/Pause
To stop, pause and restart the slideshow.
Kenya.jpg
Cairo.jpg
† Press OK to watch the picture or to start a
slideshow of the pictures in the album.
º Press OK to pause the slideshow. Press again to
restart.
◊Press one of the colour keys on the remote
control to perform the corresponding function
shown at the bottom of the screen.
If the function bar at the bottom disappeared,
press any colour key to let it reappear.
‹ Press p and select another picture or another
album.
Slideshow settings
• Details / More details
Shows the picture name, date, size and next
picture in the slideshow.
• Transitions
Shows the list of available transition styles of the
pictures.
Press o or œ to select and press OK to
activate.
26
Downloaded
From TV-Manual.com Manuals
Listen to music
Look up your songs in the Music album of your
USB device.
‡ Select the Music folder for the music files you
have stored on your USB device.
® Press π to enter the Music folder.
Ò Press o or œ to select a song or a music
album.
† Press OK to play the selected song or to play a
song followed by the next song in the same
album.
º Press one of the colour keys on the remote
control to perform the corresponding function
shown at the bottom of the screen.
If the function bar at the bottom disappeared,
press any colour key to let it reappear.
Music settings
• Details
Shows the file name.
• Repeat one/all
Repeat all songs in the album until you stop a
song or only repeat the one song selected until
you stop the song.
• Shuffle
Play songs in a random sequence.
Use more of your TV
ENGLISH
Watch a slideshow with background music
Watch a slideshow of your stored pictures
accompanied with your stored background music.
‡ Select an album of songs first and press OK.
® Highlight the Picture folder and select an album
of pictures and press OK.
5.11.4 Watch photos or listen to music from
your PC
To watch photos and listen to music from a
connected PC, make sure:
- your router and PC are switched on
- a media server software is running on your PC.
See section 7.7 PC network.
‡ Press the Source v key on the remote
control.
® Select PC network and press π.
Wait until the PC content comes on.
Ò Select the content you want to watch or listen
to and press π.
† Use p or π, o or œ to go through the
photo or music files or folders.
º Press OK to watch or listen.
◊Press p to go back to the previous list.
See section 9 Troubleshooting in case of problems
playing files or in case your PC does not appear in
the PC network menu.
5.12 Listen to digital radio
channels
If digital broadcasting is available, digital radio
channels are installed during installation.
To listen to a digital radio channel:
‡ Press OK on the remote control.
The All channels menu is displayed.
® Use the number keys to select a radio channel
available from channel number 400 onwards.
To reorder see section 6.3.3 Reorder the
channels.
Ò Press OK.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
27
5.13 Software update
Philips continually tries to improve its products. To
benefit, update the TV software regularly. To update
your TV software you need a USB Memory device
(not supplied).
Verify that your USB memory device has at least
128Mb free space. Make sure the write protection
is switched off. Some USB devices do not work
with our TV.
5.13.1 Update assistant
The Update assistant helps you to update the TV’s
software.
Step 1:TV identification
The TV has to identify with your USB memory
device.
‡ Press Menu Ï > Setup.
® Press π.
Ò Press o or œ to select Software update.
† Press π.
Setup
Software update
Installation
Update assistant
Current software ...
Software update
Local updates
Announcement
º Press o or œ to select Update assistant.
◊Press π.
‹Press OK to activate.
≈Insert a USB memory device into the USB
connector at the side of the TV.
The TV menu appears.
Ú Press the green key to proceed.
A message appears that the TV has successfully
written its identification file to the USB memory
device.
œ Press the green key again to finish.
π Remove the USB memory device from the TV.
28
Downloaded
From TV-Manual.com Manuals
Step 2: Software download from the PC to
the USB device
‡ Insert the USB memory device into a PC linked
to the internet.
® Locate and open the file update.htm on your
USB device.
Ò Read the instructions on screen and click on
the Send ID button.
If new software is available, the update is
downloaded on the USB memory device.
† Remove the USB memory device from your
PC.
Step 3: Software update transfer to the TV
The downloaded software on the USB memory
device must now be uploaded to your TV.
ç Caution
• Never remove the USB memory device from the
TV during the software update.
• If a power drop occurs during the update, do not
remove the USB memory device from the TV.
When the power retuirns, the TV continues to
update.
‡ Switch on the TV.
® Insert the USB memory device to the USB
connector at the side of the TV.
USB
Ò The TV switches off. The screen stays black for
about 10 seconds. Wait and do not use the
power switch B on the TV.
USB
Use more of your TV
≈The TV switches back on again. The update is
done.
ENGLISH
† The update process starts automatically. Please
wait.
USB
The update is finished when the message
‘Operation successful’ appears on the screen.
Pr
g
Operation Successful! Re
USB
º Remove the USB memory device from the TV.
5.13.2 Software update by digital broadcast
(DVB-T)
Your TV might receive new software from the
digital broadcast system automatically.
If you receive an update message on screen it is
strongly advised to update the software
immediately - select Now.
If you want to be reminded later on, select Later.
Select Cancel to quit the update (not
recommended). If you cancelled the update you can
still update yourself from the TV menu > Setup >
Software update > Local updates.
USB
◊Press B on the remote control.
Do not press more than once and do not use
the Power B switch on the TV.
SOURCE
UNIVERSAL MODE
TELETEXT
SUBTITLE
DEMO
‹ The TV switches off. The screen stays black for
about 10 seconds. Please, wait.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
29
6
Channel installation
The first time you turned on your TV
• you have selected the language of the TV menus
and the country where you are located
• all the available TV Channels have been installed.
This chapter provides instructions on how to
reinstall channels as well as other useful channel
installation features.
rNote:
Re-installation will modify the All channels list and
new added channels will not be added to any
favourite list.
6.1
Automatic installation
This section describes how to search for and store
all available channels automatically.
Step 1: Menu language
Sets the language of the TV menus. Go to a next
step if your language settings are correct.
‡ Press Menu Ï on the remote control and
select Setup > Installation > Languages and
press π to enter Menu language.
® Press o or œ to select your language.
Ò Press OK to confirm.
† Press p to return to the Installation menu.
Installation
Languages
Languages
Menu language
Primary audio
Channel install...
Preferences
Connections assist. Secondary subtitl..
Audio setup
Primary teletext
Secondary teletext
...
Hearing
g impaired
p
Rename devices
• Preferred teletext languages
Select one of the available teletext languages as
primary referred and secondary preferred
language.
• Hearing impaired
Select On to display the hearing impaired subtitle
version of your preferred audio or subtitle
language when available.
• Visually impaired (UK only)
Select to hear the additional commentary audio
(if available) in your selected audio language
through the loudspeakers of your TV or through
the headphones or through both
rNote:
If both Visually impaired and Hearing impaired are
enabled, the Visually impaired language will have
priority for audio, the Hearing impaired for subtitles.
• Preferred audio format
Select your preferred and available audio format
to achieve the best sound reproduction.
Select Advanced for the best sound reproduction
if a Home theatre system is connected to your
TV. Select Standard in all other cases.
Step 2: Select your country
Select the country where you are located.
The TV will install and arrange the TV channels
according to the country selected.
Go to a next step if your country selection is
correct.
‡ Press œ to select Channel installation.
® Press π to enter the Channel installation menu.
Automatic installation is highlighted.
Ò Press π to enter.
† Press OK.
The Country list appears.
º Press o or œ to select your country.
◊Press Next.
Visually im
impaired
m
Pref. audio format
The Languages menu also offers the following
language settings when digital channels are installed
and broadcasted.
• Preferred audio language
Select one of the available audio languages as
primary preferred and secondary preferred
language.
• Preferred subtitle languages
Select one of the available subtitle languages as
primary preferred and secondary preferred
language. See section 5.10 Subtitles.
30
Downloaded
From TV-Manual.com Manuals
Channel install...
Automatic install...
Automatic install... Start now
Installation update
Start-up message
Digital: Test recept...
Analogue: Manual...
Rearrange
Channel installation
rNote
You can do a Channel installation if you are both
connected to a digital antenna and a cable network.
Therefore do the installation twice. To watch the
stored Antenna channels or the stored Cable
channels, you will have to switch between Antenna
or Cable in the Channel installation > Antenna or
Cable menu.
Step 4: Install TV and radio channels
Your TV will search for and store all available digital
and analogue TV channels and all available digital
radio channels.
If you selected Cable in Step 3, a Settings menu is
available. Leave these settings unchanged unless
your provider supplied specific values to use for
Network frequency, Network ID or Symbol rate.
Follow the text on screen to change the settings.
Use the digit keys to enter the numbers. You can
also select to install analogue channels or not.
Step 5 Clock, time zone and daylight saving
selection
Only available when the country selected supports
digital broadcasts.
Go to a next step if this step is not applicable.
‡ Press œ to select Clock.
® Press π to enter.
Ò Press o or œ to select Auto clock mode.
† Press π to enter.
Installation
Clock
...
Auto clock mode
Connections assist. Time zone
Rename devices
Daylight saving
Audio setup
Decoder
Man. network inst.
Clock
Factory settings
Auto clock mode
Select Automatic to instruct your TV to always get
the time correctly. Time zone and Daylight saving
correction are automatically set.
Select Manual when Universal Time Coordinated
(UTC) is not available in your area.
Time zone/Daylight saving
When you selected Auto clock mode manually,
select your local time zone and choose between
Standard (winter) and Daylight saving time
(summer).
‡ Select Start.
The installation may take a few minutes.
In case of Cable selection, the TV can ask to
enter the Network ID supplied by the cable
provider. Enter this ID with the digit keys.
® When the installation is done, press Finish to
return to the Channel installation menu.
Ò Press Menu Ï to quit the menu.
à Tip
When digital channels are found, the list of installed
channels may show some empty channel numbers.
If you want to rename, reorder or uninstall stored
channels, see section 6.3 Rearrange channels.
Channel installation
Downloaded
From TV-Manual.com Manuals
31
ENGLISH
Step 3: Select Antenna or Cable
This selection is only available when this TV is
prepared to receive DVB-C channels in your
country.
Select Antenna to install all digital terrestrial (DVBT) and analogue channels available.
Select Cable to install all digital cable (DVB-C) and
analogue channels available.
‡ Press o or œ to select Antenna or Cable.
® Press Next.
Ò If the TV asks for it, enter the Network ID you
received from your provider.
6.2 Analogue: Manual installation
You can tune-in analogue TV channels channel by
channel manually with Manual installation.
6.2.1 Select the system
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Analogue: Manual
installation.
® Press π to enter the Manual installation menu.
System is highlighted.
Ò Press π to enter the System list.
† Press o or œ to select your country or part
of the world where you are now located.
º Press p to return to the Manual installation
menu.
Channel install...
Analogue: Manual...
Automatic install... System
Installation update Search
Start-up message
6.2.3 Fine tune a channel
Fine tune a found channel when the reception is
poor.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Analogue: manual
installation > Fine tune.
® Press π to enter the Fine tune menu.
Ò Press o or œ to adjust the frequency
† Press p when you finished fine tuning.
º Select Store current channel to store the fine
tuned channel under the current channel
number.
◊Press π to enter.
‹ Press OK.
Done appears.
≈Press Menu Ï to quit the Channel installation
menu.
Fine tune
6.3
Rearrange stored channels
To rename, reorder, uninstall or reinstall stored
channels.
Store as new ch...
Rearrange
6.3.1 Rename a channel
Assign or change a channel name to a channel for
which a name has not yet been entered.
6.2.2 Search for and store a new channel
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Analogue: manual
installation > Search.
® Press π to enter the Search menu.
Ò Press the red key to enter the frequency
yourself or press the green key to search for a
next channel.
à Tip
If you know the frequency, enter the three numbers
of the frequency with the number keys of the
remote control.
† Press p when the new channel has been
found.
º Select Store as new channel to store the new
channel under a new channel number.
◊Press π to enter.
‹ Press OK.
Done appears.
≈Press Menu Ï to quit the channel installation
menu.
32
Downloaded
From TV-Manual.com Manuals
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Rearrange.
® Press π to enter the channel list.
Ò Press o or œ in the channel list to select the
channel you want to rename.
† Press the red key.
º Press p or π to select a character or o or œ to
change the characters. Space, numbers and other
special characters are located between z and A.
◊Press the green key or OK to finish.
à Tip
To delete all characters, press the yellow key.
To delete the highlighted characters, press the blue
key..
6.3.2
Uninstall or reinstall a channel
To uninstall a stored channel so that it is no longer
possible to tune to.
Reinstall an earlier uninstalled channel.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Rearrange.
® Press π to enter the channel list.
Channel installation
6.3.3 Reorder the channels
Change the order of the stored channels.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Rearrange.
® Press π to enter the channel list.
Ò Press o or œ in the channel list to select the
channel you want to reorder.
† Press the yellow key to move up the highlighted
channel in your channel list.
º Press the blue key to move down the
highlighted channel in your channel list.
◊Press Menu Ï to quit the menu.
6.4
6.5
Digital reception test
If you receive Digital TV broadcasting you can verify
the quality and signal strength of a specific channel.
‡ Select a channel.
® Press Menu.
Ò Select Setup > Installation > Channel
installation > Digital:Test reception.
† Press π to enter
º Press OK.
◊Press the green key to start the test.
Information on the quality and the signal
strength of this channel is shown.
‹ Use the cursor keys to change the frequency to
improve the signal or enter a new frequency
directly with the digit keys.
≈Press the green key to store the frequency if
the signal quality and strength are good.
Ú Press the red key to return to the Channel
installation menu.
œ Press Menu to quit the menu.
Channel management
6.4.1 Automatic search
Once a day, at 3 AM, the TV searches for all
available TV channels automatically. Leave your TV in
standby.
Earlier found channels are updated and new
channels are stored. Channels not found by the
search anymore are removed from the channel list.
When Channel management has found or removed
channels, a message at TV start up is shown. You
can activate or deactivate this message.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Startup message.
® Select On or Off.
à Tip
To achieve the best results, contact a specialised
antenna installer.
6.6
Factory settings
You might want to return to the original factory
settings. Only picture, sound and Ambilight settings
will be reset.
‡ Press Menu Ï and select Setup > Installation
> Factory settings.
® Press π to enter the Factory settings menu.
Ò Press OK.
† Press Menu Ï to quit the menu.
6.4.2 Manual search
You can install the updates at any time.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Installation update.
® Press π to enter the Installation update menu.
Ò Press OK.
† Press the green key to start.
The update starts and may take a few minutes.
º When the update is completed, press the red
key to return to the Channel installation menu.
◊Press Menu Ï to quit the menu.
Channel installation
Downloaded
From TV-Manual.com Manuals
33
ENGLISH
Ò Press o or œ in the channel list to select the
channel you want to uninstall or reinstall.
† Press the green key to uninstall or reinstall the
channel.
º Press Menu Ï to quit the menu.
7
Connections
7.1
Connection overview
Side connectors
1 Headphones
Stereo Mini jack
2 Audio L/R
Audio L/R input to be used together with Video
or S-Video on the side of the TV.
3 Video
Video input to be used together with the
Audio L/R on the side of the TV.
4 S-Video
S-Video input to be used together with the
Audio L/R on the side of the TV.
5 USB
USB connector.
6 HDMI Side
HDMI input
7 Common interface
Slot for Conditional Access Modules (CAM)
Back connectors
8 EXT1, EXT2
Scart connectors for DVD,VCR, Digital receiver,
Game console, etc.
9 EXT3
Component Video Y Pb Pr and Audio L/R
connectors for DVD, Digital receiver or Game
console, etc.
VGA and Audio L/R connectors for a PC.
10 Service UART
For service only.
11 Digital Audio Out
Sound output cinch connector for a Home
Theatre System, etc.
12 Audio Out L/R
Sound output cinch connectors for a Home
Theatre System, etc.
13 Antenna input
14 Network
Home network connector.
15 HDMI 1, HDMI 2, HDMI 3
HDMI input connectors for Blu-ray Disc player,
HD Digital receiver or HD Game console, etc.
16 Audio L/R In [DVI to HDMI]
Audio In L/R connectors to be used together
with a DVI to HDMI connection.
34
Downloaded
From TV-Manual.com Manuals
Connections
About connections
7.2.1 What you need to know
Connect your device with the highest possible
quality connection.
Look for the highest quality connection on your
device. Use that connection to your TV.
HDMI - Highest quality ★★★★★
An HDMI connection has the best picture and
sound quality. One cable combines video and audio
signals. Use HDMI for HD ( High Definition) TV
signals. HDMI with EasyLink offers easy operating
of your connected devices when these have the
HDMI CEC standard. See section 7.2.2 EasyLink
A device connected with HDMI to the TV can only
send out audio and video signals to your TV. The
device cannot receive or record audio and video
from your TV.
YPbPr – Higher quality ★★★★
Use the Component Video YPbPr connections
together with Audio Left and Right. Match the cable
colours when you connect.
YPbPr can handle HD TV signals.
Component Video
YPbPr cable
- Red, Green, Blue
Audio L/R cable
- Red, White
Scart - Good quality ★★★
One cable combines video and audio signals.
Scart connectors can handle RGB video but no HD
TV signals.
HDMI cable (max. 5m)
à Tip
DVI to HDMI – Higher quality ★★★★
Use a DVI to HDMI adaptor if your device has only
a DVI connection.
Connect an Audio L/R cable to Audio In L/R (DVI
to HDMI) for sound.
Assign this Audio In to the HDMI 1, 2 or 3 where
the device is connected. See section 7.5.2 Audio
setup (if present).
Scart cable
S-Video - Good quality ★★
Use an S-Video cable together with an Audio L/R
(cinch) cable. Match the cable colours when you
connect.
r Note
HDMI supports HDCP (High-bandwidth Digital
Contents Protection). HDCP is a copy protection
signal that comes with HD content (DVD disc or
Blu-ray Disc).
An S-Video cable
ConnectionsFrom TV-Manual.com Manuals
Downloaded
Audio L/R cable
- Red, White
35
ENGLISH
7.2
Video - Basic quality ★
Use a Video (cinch) cable together with an Audio
L/R (cinch) cable. Match the cable colours when
you connect.
7.2.3 Display synchronised audio out
For the best match of image and sound in speech
on screen, connect a Home Theatre System to
Audio Out L/R or Digital Audio outputs. See
diagrams 7.4.4 and 7.4.8.
Do not connect the audio signal of a DVD player,
digital receiver or other audio/video device directly
to the Home Theatre System.
7.3
Connect with the
Connection assistant
(if available)
Combined Video - yellow and Audio L/R cable
- red and white
7.2.2 HDMI with EasyLink
Connected devices that are compliant with the
HDMI CEC standard can work together.
‡ Press Menu Ï > Setup > Installation >
Preferences and press π to enter the list.
® Press o or œ to select EasyLink.
Ò Press π to enter.
† Press o or œ to select On or Off.
º Select On to activate EasyLink.
Use the Connection assistant to show you how to
connect your devices to your TV. It sets all
necessary settings automatically.
You can also connect your devices without the use
of the Connection assistant. See section 7.4
Connect without the Connection assistant.
‡ Press Menu Ï on the remote control and
select Setup > Installation > Connection
assistant.
® Press π to start the Connection assistant.
Ò Press OK.
EasyLink might not work with devices from other
brands.
7.4
One touch play
Insert a DVD disc and press Play. The TV switches
on from standby and shows the DVD programme
automatically.
System standby
Press the B key on the remote control for more
than 2 seconds to switch the connected devices in
standby.
Connect without the
Connection assistant
The connections shown in this section are
recommendations for the most used cases. Other
solutions are possible.
When a device is connected the TV needs to know
what connection you made. See section 7.5
Connection setup.
System audio control
When you connect an audio system you can listen
to the sound from your TV through your audio
system while the TV speakers are muted. See
section 5.4.5 Sound settings,TV speakers.
rNote
Ensure that all HDMI-CEC features in the HDMICEC devices (for ex. Home Theatre System) are
properly set up.
36
Downloaded
From TV-Manual.com Manuals
Connections
EXT 3
SERVICE
UART
EXT 2
VGA
VGA +
Y Pb Pr
Y
ENGLISH
7.4.1 DVD player
Use a scart cable to connect the device to the
EXT1 input at the back of the TV.
EXT 1
Pb
Pr
DIGITAL
AUDIO
L
L
AUDIO
VGA / Y Pb Pr AUDIO
OUT
OUT
R
R
DVD Player
7.4.2 DVD Recorder or Digital Receiver
Use a scart cable and 2 antenna cables.
EXT 3
SERVICE
UART
EXT 2
VGA
VGA +
Y Pb Pr
Y
EXT 1
Pb
Pr
DIGITAL
AUDIO
L
L
AUDIO
OUT
R
R
VGA / Y Pb Pr AUDIO
OUT
OUT
IN
DVD Recorder / Digital receiver
7.4.3 DVD Recorder and Digital Receiver
Use 3 scart cables and 3 antenna cables.
EXT 3
SERVICE
UART
EXT 2
VGA
VGA +
Y Pb Pr
Y
EXT 1
Pb
Pr
DIGITAL
AUDIO
AUDIO
L
OUT
R
R
VGA / Y Pb Pr AUDIO
L
OUT
OUT
DVD Recorder
ConnectionsFrom TV-Manual.com Manuals
Downloaded
IN
OUT
IN
Receiver / Cable box
37
7.4.4
DVD Recorder and Home Theatre
System
Use a scart cable, 2 antenna cables and 1 digital
audio (cinch) cable.
EXT 3
SERVICE
UART
EXT 2
VGA
VGA +
Y Pb Pr
Y
EXT 1
Pb
Pr
L
L
AUDIO
VGA / Y Pb Pr AUDIO
DIGITAL
DIGITAL
AUDIO
AUDIO
OUT
OUT
OUT
R
R
OUT
DIGITAL
AUDIO
IN
IN
DVD Recorder
Home Theatre System
7.4.5
DVD Recorder and DVD Home
Theatre System
Use 2 scart cables, 2 antenna cables and 1 digital
audio (cinch) cable.
EXT 3
SERVICE
UART
EXT 2
VGA
VGA +
Y Pb Pr
Y
EXT 1
Pb
Pr
L
L
AUDIO
OUT
R
R
VGA / Y Pb Pr AUDIO
DIGITAL
DIGITAL
AUDIO
AUDIO
OUT
OUT
OUT
DVD Recorder
DIGITAL
AUDIO
IN
IN
DVD Home Theatre System
7.4.6 Satellite receiver
Use a scart cable and 2 antenna cables.
EXT 3
SERVICE
UART
EXT 2
VGA
VGA +
Y Pb Pr
Y
EXT 1
Pb
Pr
DIGITAL
AUDIO
AUDIO
L
OUT
R
R
VGA / Y Pb Pr AUDIO
L
OUT
Satellite receiver
38
Downloaded
From TV-Manual.com Manuals
Connections
HD Digital receiver / HD satellite
receiver
Use an HDMI cable and 2 antenna cables.
ENGLISH
7.4.7
NETWORK
L
HDMI
OUT
R
AUDIO IN
[ DVI HDMI ]
HDMI 1
HDMI 2
HDMI 3
OUT
IN
HD Digital receiver / HD Satellite receiver
7.4.8
DVD-R, Home Theatre System and
Digital receiver
Use 3 scart cables, 3 antenna cables and 1 audio
(cinch) cable.
EXT 3
VGA +
Y Pb Pr
Y
EXT 1
Pb
Pr
DIGITAL
DIGITAL
AUDIO
AUDIO
OUT
OUT
L
L
AUDIO
OUT
R
R
VGA / Y Pb Pr AUDIO
SERVICE
UART
EXT 2
VGA
OUT
OUT
IN
DVD Recorder
IN
Digital Receiver
DIGITAL
AUDIO
IN
Home Theatre System
7.4.9 Blu-ray Disc player
Use an HDMI cable.
NETWORK
L
R
AUDIO IN
[ DVI HDMI ]
HDMI 1
HDMI 2
HDMI 3
HDMI
OUT
Blu-ray Disc player
ConnectionsFrom TV-Manual.com Manuals
Downloaded
39
7.4.10 Game console
The most practical connections for a game console
are at the side of the TV.
Connected at the side of the TV
Use the HDMI connection or the S-Video and
Audio L/R connections or the Video and Audio L/R
connections.
Connected at the back of the TV
Use an HDMI connection or the EXT3-YPbPr and
Audio L/R connections for HD quality.
EXT 3
VGA +
Y Pb Pr
VGA
Y
Pb
Pr
EXT 3
VGA +
Y Pb Pr
R
HDMI 1
HDMI 2
VGA / Y Pb Pr AUDIO
L
Connected at the back of the TV
Use an HDMI connection or the EXT3-YPbPr and
Audio L/R connections for HD quality
HDMI 3
VGA
Y
Pb
Pr
HDMI 1
HDMI 2
VGA / Y Pb Pr AUDIO
L
R
HDMI 3
7.4.11 Camcorder
The most practical connection for a camcorder is at
the side of the TV.
Connected at the side of the TV
Use the HDMI connection or the Video and Audio
L/R connections or use the S-Video and Audio L/R
connections.
40
Downloaded
From TV-Manual.com Manuals
Connections
PC to TV connection
Use a PC-TV out cable to S-Video and Audio L/R
cable to connect to the side of the TV.
AUDIO L/R
S-VIDEO
ç Caution
Before connecting the PC, set the PC monitor
refresh rate to 60Hz.
AUDIO L/R
à Tip
Set the TV picture format to Unscaled in the
Picture format menu for maximal PC picture
sharpness. See section 5.4.4 Widescreen picture
format.
DVI to HDMI connection
Use a DVI to HDMI adaptor to connect to the
HDMI side connection.
Connect the Audio L/R at the side for sound.
ENGLISH
7.4.12 Personal Computer
You can connect your PC directly to the TV.
The TV works as a monitor of your PC.
For more features you can connect your PC in a
PC network. See section 7.7 PC network.
As a monitor the PC can be connected at the side
with a DVI to HDMI adaptor or with a PC to TV
cable. Alternatively you can connect the PC at the
back with the VGA connection.
S-VIDEO
VGA connection
Use a VGA cable to connect the PC to the EXT3
connection at the back of the TV.
Connect the Audio L/R to the EXT3 Audio L/R.
VGA
EXT 3
VGA
AUDIO L/R
VGA +
Y Pb Pr
b
Pr
AUDIO L/R
VGA / Y Pb Pr AUDIO
L
R
VGA
DVI-HDMI
HDMI
AUDIO L/R
AUDIO L/R
For supported PC monitor resolutions, see section
8 Technical data.
ConnectionsFrom TV-Manual.com Manuals
Downloaded
41
7.5
Connection setup
The TV needs to know what connections you have
made and which device is connected to which
connector.
If you have used the Connection assistant the
connection setup is already done.
7.5.1 Naming your devices
Name the connected devices for easy selection and
best signal handling.
Assign the type of device (DVD, VCR, Game, ...) to
the connector you use for that device.
‡ Press Menu Ï on the remote control and
select Setup > Installation> Rename devices.
® Press π to enter the list.
Ò Press o or œ to select the connector you
used for the device you connected.
† Press π.
º Press o or œ to select the type of device.
◊Press Menu Ï to quit the menu.
7.5.2 Audio setup (if present)
If you use the Audio In L/R (DVI to HDMI)
connector for a device connected to HDMI at the
back of the TV, assign this Audio In to the HMDI 1,
2 or 3 where the device is connected.
‡ Press Menu Ï on the remote control and
select Setup > Installation > Audio setup.
® Press π twice.
Ò Press o or œ to select the HDMI connection
to link with this Audio In.
Audio setup
Audio in L/R
Audio in L/R
None
HDMI 1
HDMI 2
7.5.3 Decoder channels
Decoders that decode an antenna channel are
connected to EXT1 or EXT2 (scart).
You have to assign the TV channel as a channel to
be decoded. Then assign the connection where the
decoder is connected
‡ Press Menu Ï on the remote control and
select Setup > Installation > Decoder >
Channel.
® Press π to enter the list.
Ò Press o or œ to select the channel to decode.
† Press p and go back to select Status.
º Press o or œ to select the connector used by
the decoder.
◊Press Menu Ï to quit the menu.
Installation
Decoder
...
Channel
Connections assist. Status
Rename devices
Audio setup
Decoder
Man. network inst.
Clock
Factory settings
HDMI 3
42
Downloaded
From TV-Manual.com Manuals
Connections
Preparing for digital
services
ENGLISH
7.6
Scrambled digital TV channels can be decoded with
a Conditional Access Module (CAM) and a Smart
card provided by a digital TV service operator. The
CAM may enable several services depending on the
operator you choose (e.g. Pay TV).
Contact your digital TV service operator for more
information and terms.
7.6.1
Insert a Conditional Access Module CAM
) Warning
Switch off the TV before inserting the CAM.
Look on the CAM for the correct inserting
direction. Incorrect insertion can damage the CAM
and the TV.
‡ Gently insert the CAM into the Common
Interface slot at the side of your TV as far as it
will go.
® Leave the CAM in the Common Interface slot
permanently.
It can take a few minutes before a CAM is
activated. Removing the CAM will deactivate the
digital TV service.
COMMON INTERFACE
7.6.2 Common interface menu
From this menu you access the CAM service you
have installed. The applications and their function,
the content and the messages on screen come
from the CAM service provider.
‡ Press Menu Ï on the remote control and
select Features > Common interface.
This menu option is available when a CAM is
inserted and has made contact with the provider.
ConnectionsFrom TV-Manual.com Manuals
Downloaded
43
7.7
PC network
You can link up your TV on a PC network in your
home. Watch your photos and listen to your music
from any linked PC on the TV. The PC network
feature of this TV is DLNA certified.
You can use Microsoft Windows XP or Vista, Intel
Mac OSX or Linux.
An example of a home PC network.
† Some media server software needs a setting to
share your files with the TV.
In the media server this TV will present itself as
a number - a MAC or IP number.
Have the TV and router switched on for this
number to appear in the media server.
Select the TV number in the media server and
set the server to share files with this number.
For media server software marked with an * in
sections 8 Technical data, a step by step setting
instruction is available. See section 7.7.4 Media
server settings.
A firewall, a security system on your computer,
could also block the network connection.
Allow the media server software to go to the
network.
7.7.1
What you need
To set up your TV in a home PC network you
need:
• a router and a computer in a home network
• a network cable
• recent media server software (Windows, media
Player 11 or similar) on your computer.
For a complete list of compatible media server
software see section 8 Technical data.
7.7.2
Set up a PC network connection
On the TV no special settings are necessary to
connect automatically to the network.
‡ Connect the network cable from your router to
the Network
connector at the back of the
TV.
º Press the Source v key on the remote
control.
◊Select PC network and press π.
It could take some time for the TV to connect.
‹Use the colour and navigation/rotation keys to
browse your folders or play your files.
If the TV cannot connect to the network, study the
server software, router or PC manuals.
7.7.3 Manual network setup
Some expert network settings can be set on the
TV. The DHCP is set to On to automatically
connect to the network.
Press Menu Ï > Setup > Installation > Manual
network installation.
NETWORK
L
R
AUDIO IN
[ DVI HDMI ]
HDMI 1
HDMI 2
HDMI 3
® Switch on the router. Set the router to DHCP
On.
Ò Switch on the computer and start the media
server software.
44
Downloaded
From TV-Manual.com Manuals
Connections
Media servers need to be set for sharing their files
and folders. Follow the instructions closely to set
your specific server.
Windows Media Player v11on Windows Vista
Set for network sharing
Set Network discovery to On. Set File sharing to
On. Go back to the Media Sharing window in
Windows Media Player and check the Share my
media box. Click OK.
ENGLISH
7.7.4 Media server settings
When the TV is connected, by the router, to the
PC and everything is switched On, the Media
sharing window will show the TV as an Unkown
Device. Select the device and click Allow.
In Windows Media Player select Library from the
menu and select Media sharing.
1
2
In the Media Sharing window, check the Share my
media box. Click OK.
You can open the Settings window to change
particular settings on sharing.
When the device icon (the TV) is checked with a
green tick, click OK.
Set folders for sharing
In Windows Media Player select Library from the
menu and select Add to Library.
1
2
If no network connection was found, and you are
unable to check this box, click the Networking
button to show the Network and Sharing Center
window, …
In the Add To Library window, select My folders
and those of others that I can access and click
the Advanced Options button. …
1
2
ConnectionsFrom TV-Manual.com Manuals
Downloaded
45
1
2
With Advanced Options open, you can add
specific folders to the list to share. Click Add.
1
Now everything is set to enjoy music, photos and
videos on your TV.
In the Add Folder window select a folder with
music, photos or videos you want to share with
other devices (your TV). Click OK.
Windows Media Player v11 on Windows XP
Set for network sharing
In Windows Media Player select Library from the
menu and select Media sharing …
1
2
In the Add To Library window the newly added
folder is shown. You can add more folders to
share. Click the OK button to add the files to the
library.
46
Downloaded
From TV-Manual.com Manuals
Connections
With Advanced Options open, you can add
specific folders to the list to share. Click Add.
ENGLISH
In the Media Sharing window, check the Share my
media box.
When the TV is connected, by the router, to the
PC and everything is switched On, the Media
sharing window will show the TV as an Unkown
Device. Select the device and click Allow.
1
1
2
3
You can open the Settings window to change
particular settings on sharing.
When the device icon (the TV) is checked with a
green tick, click OK.
In the Add Folder window select a folder with
music, photos or videos you want to share with
other devices (your TV). Click OK.
Set folders for sharing
In Windows Media Player select Library from the
menu and select Add to Library.
In the Add To Library window the newly added
folder is shown. You can add more folders to
share. Click the OK button to add the files to the
library.
In the Add To Library window, select My folders
and those of others that I can access and click
the Advanced Options button.
ConnectionsFrom TV-Manual.com Manuals
Downloaded
47
Click the Sharing tab.
1
Set folders for sharing
Click the green plus icon and select Add folder…
1
2
Now everything is set to enjoy music, photos and
videos on your TV.
TVersity v.0.9.10.3 on Windows XP
In the Add media pop-up window, click the
Browse button.
Set for network sharing
Click the Settings tab and click the Start Sharing
button.
1
2
1
In the Browse for Folder window select a folder
with music, photos or videos you want to share.
Click OK.
A pop-up window tells you that the media
server service is started. Click OK.
48
Downloaded
From TV-Manual.com Manuals
Now everything is set to enjoy music, photos and
videos on your TV.
Connections
Set for network sharing
In the blue frame click the hard disk name to
browse to a folder with music, photos or videos
you want to share with other devices (your TV).
ENGLISH
Twonky Media v4.4.2 on Macintosh OS X
In Twonky Media click Basic Setup > First steps.
In this window you can change the server name
that appears on your TV.
1
2
Click Select to select the folder for sharing.
Now click Save Changes.
Click Basic Setup > Clients/Security.
Check the box next to Enable sharing for new
clients automatically.
Then click Rescan content directories.
In some cases this might not make all files and
folders available.
Set folders for sharing
Click Support > Troubleshooting and click
Rebuild database to make sure everything
works OK. This rebuilt might take a while.
Click on Basic Setup > Sharing.
Some ‘Content Locations’ might be set already
automatically. To add a folder (a content location)
to be shared on the network click the Browse
button.
Now everything is set to enjoy music, photos and
videos on your TV.
1
2
ConnectionsFrom TV-Manual.com Manuals
Downloaded
49
8
Technical data
Picture / Display
• Display type: LCD Full HD W-UXGA
• Panel resolution: 1920x1080p
• Perfect Pixel HD picture enhancement
• 1080p 24/25/30/50/60Hz processing
• 100 Hz Clear LCD (if present)
Supported display resolutions
• Computer formats
Resolution
Refresh rate
640 x 480p
60Hz (VGA/HDMI)
600 x 800p
60Hz (VGA/HDMI)
1024 x 768p
60Hz (VGA/HDMI)
1280 x 768p
60Hz (VGA/HDMI)
1360 x 765p
60Hz (VGA/HDMI)
1360 x 768p
60Hz (VGA/HDMI)
1280 x 1024p
60Hz (HDMI)
1920 x 1080i
60Hz (HDMI)
1920 x1080p
60Hz (HDMI)
• Video formats
Resolution
Refresh rate
480i
60Hz
480p
60Hz
576i
50Hz
576p
50Hz
720p
50Hz, 60Hz
1080i
50Hz, 60Hz
1080p
24Hz, 25Hz, 30Hz
1080p
50Hz, 60Hz
Tuner / Reception / Transmission
• Antenna input: 75ohm coaxial (IEC75)
• TV system: DVD COFDM 2K/8K,
(MPEG2, MPEG4 if available)
• Video playback: NTSC, SECAM, PAL
• DVD: DVB Terrestrial
(see selected countries on the TV typeplate)
Sound
• Sound system:
- Virtual Dolby Digital
- BBE
Multimedia
• Connections: USB
• Playback formats: MP3, Slideshow (.alb)
JPEG, MPEG1, MPEG2.
50
Downloaded
From TV-Manual.com Manuals
Supported media server software
• Windows Media Player 11 (on Microsoft
Windows XP* or Vista*)
• PacketVideo Twonky Media 4.4.2 (on PC* &
Intel Mac OSX*)
• Sony Vaio media server (on Microsoft Windows
XP or Vista)
• TVersity v.0.9.10.3 (on Windows XP*)
• Nero 8 - Nero MediaHome (on Microsoft
Windows XP)
• DiXiM (on Windows XP)
• Macrovision Network Media Server (on
Windows XP)
• Fuppes (on Linux)
• UShare (on Linix)
• Philips Media Manager (on Microsoft Windows
XP)
• Philips NAS SPD8020
* For this media server software a step by step
setting instruction is available in the online User
manual on www.philips.com/support.
Supported USB/Memory device formats
• FAT 16, FAT 32, NTFS.
Remote control
• Type: RC4492
RC4494 (42PFL9803)
• Batteries: 3 Size AAA-LR03-1,5V type
Connectivity
Back
• EXT1 (scart): Audio L/R, CVBS in, RGB
• EXT2 (scart): Audio L/R, CVBS in, RGB,
• EXT3: Y Pb Pr or VGA, Audio L/R
• HDMI 1 in (HDMI 1.3a for all HDMI
connections)
• HDMI 2 in
• HDMI 3 in
• Audio In L/R (DVI to HDMI)
• Audio Out L/R - display synchronised
• Digital Audio out (coaxial-cinch-S/PDIF) display synchronised
• Network - (RJ45)
Side
• HDMI side in
• S-Video in (Y/C)
• Video in (CVBS)
• Audio L/R in
• Headphone (stereo mini jack)
• USB
• Common interface slot
Technical data
ENGLISH
Power
• Mains power: AC 220-240V (±10%)
• Power and standby power consumption:
See technical specification on www.philips.com
• Ambient temperature: 5°C - 35°C
Specifications are subject to change without notice.
For more specification details of this product see
www.philips.com/support.
Dimensions and weights (approx.)
TV model
32PFL9603D/H 37PFL9603D/H
32PFL9613D/H
- width
- height
- depth
- weight
TV + stand
- width
- height
- depth
- weight
828mm
534mm
109mm
± 19kg
953mm
604mm
101mm
± 25kg
828mm
594mm
220mm
± 20kg
953mm
677mm
242mm
± 28,5kg
Technical data
Downloaded
From TV-Manual.com Manuals
42PFL9603D/H
42PFL9703D/H
42PFL9803H
1054mm
658mm
100mm
± 28kg
1054mm
731mm
265mm
± 32,5kg
47PFL9603D/H
47PFL9703D/H
52PFL9703D/H
1167mm
722mm
101mm
± 35,5kg
1300mm
803mm
127,5mm
± 45,5kg
1167mm
795mm
290mm
± 40,5kg
1300mm
875mm
320mm
± 49kg
51
9
Troubleshooting
Television and remote control
The TV does not switch on
• Verify the mains cord connection.
• Verify if the batteries of the remote control are not
empty or weak.Verify their + / - orientation.
You can use the keys on the TV to switch the TV on.
• Unplug the mains cord, wait a minute and plug it
back in.Try again to switch on.
The TV does not react on the remote control
• Verify if the batteries of the remote control are not
empty or weak.Verify their + / - orientation.
• Clean the remote control and TV sensor lens.
The TV switches off and the red light blinks
• Unplug the mains cord, wait a minute and plug it
back in.Verify if there is enough space for ventilation.
Wait until the TV has cooled down. When the TV
does not restart to standby and the blinking occurs
again, call our Customer Care.
You forgot your code to unlock Child lock
• See section 5.9.3 Set code / Change code.
Wrong language in the TV menu ?
Follow these steps to change the language.
‡ Press Menu Ï on the remote control.
® Use œ to select the last menu line.
Ò Press πthree times.
† Press o or œ to select your language.
º Press OK.
◊Press Menu Ï to quit the menus.
TV channels
Some TV channels are gone
• Verify if the correct channel list is chosen.
• A channel could be uninstalled in the Rearrange
menu.
No digital channels found during installation
• Verify if the TV supports DVB-T or DVB-C in your
country. See the label “Digital TV Country
Compatibility” on the back of the TV.
Picture
LightGuide is on but there is no picture
• Verify if the antenna is connected properly.
• Verify if the correct device is selected.
The sound is on, but there is no picture
• Verify the contrast or brightness setting in the menu.
The TV picture is poor
• Verify if the antenna is connected properly.
• Non-earthed audio devices, neon lights, high
buildings or mountains can influence the picture
quality.Try to improve the picture by changing the
antenna direction or place devices away from the
TV.
• Verify if the correct TV system is chosen in the
Manual installation menu.
• If only a certain channel is poor, try to fine tune this
channel in the Fine tune menu. See section 6.2.3.
The picture has poor colour
• Verify the colour settings in the Picture menu.
Select any of the Reset to standard settings in the
Smart settings menu. See section 5.4.1.
• Verify the connections and cables of the connected
devices.
The TV does not remember my settings when I
switch back on
• Verify if the TV is set to Home in the TV menu >
Setup > Installation > Preferences > Location
menu.
The picture does not fit the screen, it is too big or
too small
• Select a more fitting picture format in the Picture
format menu.
See section 5.4.4 Widescreen picture format.
• Name your connected device in the Connections
menu to obtain the best signal handling.
See section 7.4.1 Naming your devices.
The picture position on screen is not correct
• Some picture signals from some devices do not fit
the screen correctly.You can shift the picture with
the navigation key on the remote control.Verify the
signal output of the device.
Sound
There is a picture but no sound
• Verify the volume is not set to 0.
52
Downloaded
From TV-Manual.com Manuals
Troubleshooting
USB connection
The sound is poor
• Verify if the sound is set to Stereo.
• Verify the Equalizer in the Sound menu.
• Select any of the Smart settings in the menu.
The TV does not show the USB device content
• Set your device (camera) to ‘Mass Storage Class’
compliant.
• The USB device may need specific driver software.
Unfortunately this software cannot be downloaded
to your TV.
I cannot see my files in the Multimedia menu.
• Not all audio and picture files are supported. See
section 8 Technical data.
The sound comes from one speaker only
• Verify if the Balance is not set to extreme left or
right.
Photo and music files do not playback smoothly
• The transfer performance of the USB device limits
the transfer rate.
Sound delay when A HTS-DVD device is connected
• See the user manual of the HTS-DVD device to
adjust the audio sync delay.
If you cannot set A delay, switch off HD Natural
MOtion in the Picture > Perfect Pixel HD menu.
See section 5.4.3 Picture settings.
Personal computer
The PC display on my TV is not stable or is not
synchronised
• Verify if the correct resolution mode is selected on
your PC. See section 8 Technical data.
HDMI connections
Trouble with devices connected with HDMI
• The HDMI - HDCP procedure might take a few
seconds before the TV shows the picture from a
device.
• If the TV does not recognise the device and the
screen shows no picture, try switching from one
device to another and back again to restart the
HDCP procedure.
• If sound interruptions occur persistently, see the user
manual of the device to verify the output settings. If
that does not help, connect an additional audio
cable.
• If a DVI to HDMI adaptor is used, verify if an
additional audio connection is in place to complete
the DVI connection.
• HDMI with EasyLink does not work
- Verify if the connected device supports the HDMI
CEC standard. See the user manual that comes
with the device.
- Verify if the HDMI cable is properly connected.
- Verify if Easylink is activated in the Setup,
Installation, Preferences menu.
- Ensure that the System audio control in your
HDMI CEC audio devices is properly set up. See
the user manual that comes with your audio
device.
I cannot find my PC files on my PC
• Verify if files have been added in the folder.
• Not all file formats are supported. See section 8
Technical data.
PC files are not shown in the PC network menu
• You have to set the PC media server to share files
with the TV. See section 7.7.2 Set up a PC network
connection.
PC files do not play
• See section 8 Technical data for supported file
formats.
If your problem is not solved
Switch your TV off and on again, that may help. If not,
call our Consumer Care or consult our website
www.philips.com/support.
Find the Consumer Care telephone numbers on the
back cover of this manual.
Please, have the TV Model and Product Number
ready before you call.
You can find these numbers on the packaging label or
on the typelabel on the back and bottom of the TV.
) Warning
Never try to repair the TV yourself.
Troubleshooting
Downloaded
From TV-Manual.com Manuals
53
ENGLISH
• Verify the sound has not been muted with the ¬
key.
• Verify if all cables are connected properly.
• If no sound signal is detected, the TV automatically
switches off the sound.
This is proper operation and is not a malfunction.
10 Index
100 Hz Clear LCD 5,17
A
Active control 17
Advanced sharpness 17
Ambilight
active mode 19
LoungeLight 11
menu / settings 19
modes 19
Analogue
manual installation 31
TV channels 31
Antenna
cable 7
connect 7
with devices 34
Audio setup 42
Auto clock mode 31
Auto format 18
Automatic installation 30
Auto surround 19
Auto Volume levelling 19
Channel
management 32
up/down 13
previous 13
rearrange 32
store / install 31
Child lock 24
Clock 13,31
Code 24
Colour
enhancement 17
menu 17
keys 4,12
Common interface (CAM)
menu 43
slot 34,43
Connection
best 35
overview 34
set up 42
Contrast 17
Country selection 30
Custom lock 24
Custom tint 17
B
Balance
sound 19
Batteries 3,7
Blacklevel 17
Blu-ray Disc 39
Brightness 17
ambilight 19
C
CA module 43
Cable
HDMI 35
Scart 35
S-Video 35
Video 36
YPbPr 35
Camcorder 40
Camera (photo) 40
Care of the screen 3
Change code 24
Channel
all channels list 21
favourite list 21
installation 30
lock 24
D
Daylight saving 31
Decoder channel 42
Delta volume 19
Device
connecting 36
naming 42
watch 9
DHCP 44
Digital
audio out 34
subtitle language 25
receiver 37
text services 21
test reception 33
Dual I/II 19
Dual screen 13
DVB-T 5
DVD
connect 37
playback 10
player 37
recorder 37,38
54
Downloaded
From TV-Manual.com Manuals
Dynamic
backlight 17
contrast 17
E
EasyLink 36
Electronic Programme Guide 22
Energy saving 16
Equalizer 18
External 1,2,3 (EXT) 34
F
Factory settings 33
Favourite channel lists 21
Fine tune 32
G
Game console 40
H
HDCP 35
HDMI connection 35
HD digital receiver 39
HD natural motion 17
Headphone
connect 4,34
volume 19
Hearing impaired 30
Home theatre system 38
Hue 17
I
Installation
automatic 30
manual 31
manual network setup 44
menu 30
update 32
K
Kensington Security Slot 5
Key(s)
colour 12
on TV 4
on remote control 4,12
L
Language
menu 30
audio 19
Index
M
Menu key 13
Mono 19
Movie expand 18
MPEG artefact reduction 17
Music 25
Mute key 12
N
Naming devices 42
Network setup 44
Noise reduction 17
O
OK key 12
On timer 24
S
Safety 3
Satellite receiver 38
Scart connection 35
Screen cleaning 3
Search
channels 31
teletext pages 20
Set code 24
Settings assistant 16
Sharpness 17
Sleeptimer 24
Smart settings 16
Software update 28
Sound
menu 18
surround mode 19
Standby 12,24
Super zoom 18
Stationary images 3
Stereo 19
Subtitle 25
language 25
shift 18
Switch on 8
V
VCR
connect 37
VGA 41
Video cable 36
Video formats 50
Visual impaired 30
Volume
bar 18
key 12
visual impaired 19
ENGLISH
Language
subtitle 25
LightGuide 15
Light sensor 17
Location 47
Locks 24
LoungeLight 11
W
Whitepoint 17
Widescreen picture format 18
Y
YPbPr 35
P
Perfect Pixel HD 17
Personal Computer
connect 41
display resolutions 50
Photo viewer 26
Picture
album 26
format 18
menu 17
Position the TV 5
Power cable 7
Preferred audio format 30
R
Radio channel 27
Rearrange channels 32
Recorder 37
Recycling 3
Remote control
assistant 13
batteries 7
mode 13
overview 12
setup code 16
Remote control
universal 13
Rename 32
Reorder 32
T
Table of Pages T.O.P 20
Technical data 50
Teletext 20
digital 21
dual screen 20
language 20
menu 21
page 20
teletext 2.5 21
Time zone 31
Timers 24
Tint 17
Troubleshooting 52
TV speakers 19
U
Universal mode 13
Universal remote control 13
Unmount the stand 6
Unscaled 18
USB
connector 34
device 25
photo viewer 25
Index
Downloaded
From TV-Manual.com Manuals
55
Information about how to
re-tune your TV during the
digital TV switchover.
Keep this user manual safe
- you'll need it.
.........................................
Television in the UK is going digital, bringing us all
more choice and new services. Starting in late 2007
and ending in 2012, television services in the UK
will go completely digital, TV region by TV region.
Please see the next page to find out when your area
switches to digital.
Digital UK is the independent, non-profit organisation leading the process of digital TV switchover in
the UK. Digital UK provides impartial information on
what people need to do to prepare for the move to
digital, and when they need to do it.
56
Downloaded
From TV-Manual.com Manuals
How the switch over affects your
TV equipment :
Your new TV has a digital tuner built in, which
means it is ready to receive the Freeview signal by
simply plugging it into your aerial socket (check if
you can get digital TV through your aerial now, or
whether you'll have to wait until switchover, at
www.digitaluk.co.uk).
When the TV switchover happens in your area, there
are at least two occasions when you will need to
re-tuner your TV in order to continue receiving your
existing TV channels, and also to pick up new ones.
If you have any questions, please contact your
equipment supplier or call Digital UK on ...
0845 6 50 50 50 or visit www.digitaluk.co.uk
How to re-tune:
ENGLISH
Digital UK, the body leading the digital TV switchover, will advise you when you need to re-tuner
during the switchover.
If you choose to connect your TV to satellite or
cable with a digital box then it will no be affected
by switchover, and you won't need to re-tune.
To find out how to re-tune your TV, check this user
manual for details.
Go to section 6.1 Automatic installation and go to
Step 4 Install TV and radio channels.
If you do not re-tune your channels when advised to
do so by Digital UK, you may lose some or all of`
your channels until you do re-tune. You should
re-tune your TV every few months to check for any
new channels.
If you are missing any channels, it may be that they
are not available in your area, or that your aerial
needs upgrading.
When does switchover happen?
* Copeland switches on October 17, 2007
The exact date you switch
depends on the transmitter
you are served by. To check
when you switch, go to
Digital UK's postcode
checker on
www.digitaluk.co.uk.
Check your ITV news service
or look at Teletext page 106
to see what TV region you're
in.
Visit us at digitaluk.co.uk
Call us on 0845 6 50 50 50*
* Calls charged at BT rate of 3p pr minute daytime and
1p per minute evenings and weekends. Rates may vary
for calls from non-BT lines.
Downloaded From TV-Manual.com Manuals
57
Downloaded From TV-Manual.com Manuals
Codici per il telecomando
Códigos de acceso para el mando a distancia
Códigos de introdução no telecomando
Remote control setup codes
Codeeinstellung in die Fernbedienung
Codes de la télécommande
Instelcodes voor de afstandsbediening
DVD
DVD player
DVD recorder
DVD-R HDD
Blu-ray Disc
¶›Ó·Î˜ Έ‰ÈÎÒÓ Î·Ù·¯ÒÚÈÛ˘ ÙËϯÂÈÚÈÛÙËÚ›Ô˘
STB
HTS
Digital receiver Home Theatre Systems
- DVB-T
Amplifier
Satellite receiver
- DVB-S
Cable receiver
- DVB-C
Daewoo 0007, 0008, 0009, 0125, 0139,
0261, 0286
DVD Codes
Jeutech 0056
JVC
0012, 0049, 0106, 0117, 0133, 0214,
Dalton
0069
0215, 0216, 0217, 0237, 0238,
PHILIPS 0000, 0001, 0002, 0003, 0013,
Dansai
0054, 0188
0239, 0240, 0276, 0277, 0278,
0021, 0030, 0049, 0100, 0105,
Daytek
0110, 0121
0107, 0111, 0123, 0127, 0131,
DEC
0060
0135, 0145, 0150, 0153,
Denon 0015, 0039, 0166, 0173, 0184
0154,0155, 0156, 0161, 0163,
Denver 0032, 0060, 0066, 0118, 0172, 0308
Kingavon 0060
0164, 0177, 0193, 0197, 0204,
Denzel
0051
Kiss
0051, 0061
0221, 0225, 0226, 0231, 0232,
Desay
0059
Koda
0060
0233, 0258, 0260, 0271, 0273,
Diamond 0055, 0126
KXD
0062
0275, 0288, 0289, 0295, 0301,
Digitor
Lawson 0126
0310, 0311, 0312, 0318, 0320,
DK Digital 0134, 0292
Lecson
0054
0325, 0333, 0341, 0342, 0343,
Dmtech
0005
Lenco
0060
0354, 0355
LG
0067
Dual
0051
Aiwa
0028, 0109, 0140, 0171, 0303
DVX
0126
Aika
0020
Easy Home
0062
0279, 0293, 0329, 0335
Kenwood
0015, 0043, 0138, 0181, 0186,
0300
0026, 0114, 0160, 0213, 0304,
0324, 0338, 0352, 0359
Life
0022, 0023, 0024
Akura 0066
Eclipse
0055
Lifetec
0022, 0023, 0024, 0037
Alba
0004, 0118, 0119, 0129, 0195, 0256
Elta
0015, 0033, 0136
Limit
0126
Apex
0040
Eltax
0290
Loewe
0021, 0146, 0174
Bang & Olufsen 0071
Emerson 0026
LogicLab 0126
Best Buy 0062
Enzer
0051
Luxor
Bosston
Finlux
0055
Magnavox 0049, 0060, 0100
Brandt 0049, 0115, 0132, 0191
Fisher
0029
Magnum 0024, 0037
Brittannia 0053
Gericom 0144
Marantz 0030, 0164, 0175, 0176
Bush
Global Solutions 0126
Matsui
0132, 0194
0119, 0120, 0134, 0141, 0147,
Global sphere 0126
MBO
0046
0183, 0185, 0189, 0256
0056
0004, 0032, 0050, 0052, 0060, 0064,
0144
Go Video 0018
Mediencom
Cambridge Audio 0055, 0070
Goldstar
Medion 0006, 0022, 0023, 0024, 0037, 0064
CAT
Goodmans 0004, 0060, 0064, 0119, 0144,
0057, 0058
0114
0147, 0169, 0179, 0187, 0236, 0256
Celestial 0068
0053
Metz
0055
MiCO
0055
Centrex 0144
Graetz 0051
Micromaxx 0022, 0023, 0024, 0037
Centrum 0058
Grundig 0021, 0031, 0139, 0144, 0148
Micromedia 0049
CGV
H&B
0060, 0061
Micromega
0105, 0271
Cinevision 0063
Haaz
0055, 0126
Microstar
0022, 0023, 0024, 0037
Classic
Harman/Kardon 0045
Mirror
Clatronic 0060
HiMAX 0062
Mitsubishi 0017, 0101
Conia
0050
Hitachi 0018, 0037, 0051, 0062, 0196, 0209,
Mizuda 0060, 0062
Crypto
0065
0284, 0302, 0317, 0330
C-Tech
0126
0055
0034
CyberHome 0108, 0124, 0137
0064
Monyka0051
Humax 0157
Mustek
Innovation 0022, 0023, 0024, 0037
Mx Onda 0055
Downloaded From TV-Manual.com Manuals
0034, 0256, 0296
1
NAD
0044
Shinco
0035
STB Codes
Naiko 0144
Sigmatek 0062
Nakamichi 0048
Silva
Neufunk 0051
Singer 0055, 0126
0066, 0068, 0069, 0073, 0085,
NU-TEC 0050
Skymaster 0033, 0034, 0126
0087, 0095, 0097, 0098, 0105,
Omni
Skyworth 0066
0109, 0113, 0114, 0117, 0122,
Onkyo 0025, 0049, 0100, 0182
SM Electronic 0126
0124, 0174, 0176, 0184, 0187,
Optim 0054
Sony
0014, 0104, 0109, 0122, 0171, 0178,
0206, 0207, 0208, 0211, 0213,
0192, 0222, 0223, 0224, 0228,
0281, 0282, 0285, 0297, 0298,
Orava 0060
0229, 0230, 0282, 0297, 0306,
0301, 0304, 0325, 0331, 0358,
Orion 0185
0309, 0316, 0323, 0351
0360, 0361, 0386, 0387, 0393,
0053
Optimus
Oritron
0066
0019, 0103
0024
PHILIPS 0000, 0001, 0003, 0020, 0043,
Soundmaster 0126
0395, 0412, 0421, 0429, 0434
Soundmax0126
ABC
Pacific 0126
Standard
AB Sat 0100, 0122, 0123, 0132
Palsonic
Star Cluster
P&B
0060
0052
0126
0126
0432
AGS
0122
Starmedia 0060
Akai
0043, 0105
0200, 0243, 0244, 0245,0246, 0247,
Supervison 0126
Alba
0002, 0003, 0004, 0005, 0031, 0045,
0248, 0249, 0250, 0251, 0252,
Synn
0253, 0254, 0266, 0267, 0274,
Tatung 0125
Alcatel 0430, 0431
0291, 0294, 0313, 0314, 0315,
TCM
Aldes 0004, 0005, 0006, 0072, 0107
Panasonic 0015, 0165, 0184, 0198, 0199,
0126
0087, 0107, 0123, 0209, 0270
0022, 0023, 0024, 0037, 0072, 0073,
0319, 0336, 0347, 0348, 0349,
0074, 0075, 0076, 0077, 0078,
Allsat 0007, 0025, 0042, 0061, 0068, 0105
0356, 0358
0079, 0080, 0081, 0082, 0083,
Allsonic 0005, 0010, 0072, 0108, 0115
Philips Magnavox 0013
0084, 0085, 0086, 0087, 0088,
Alltech 0089, 0123
Pioneer0019, 0103, 0112, 0113, 0116, 0128,
0089, 0090, 0091, 0092, 0134,
Alpha 0105
0210, 0269, 0272
Altai
0149, 0159, 0180, 0201, 0202,
Proline
Teac
0019, 0050, 0126, 0168
Amitronica 0123
0255, 0263, 0305, 0321, 0326,
Tec
0066
Ampere 0008, 0078, 0222
0327, 0328, 0337, 0344, 0345,
Technics 0170, 0184
0346, 0353, 0357
Telefunken
0144, 0194
Tevion 0022, 0023, 0024, 0037, 0069, 0126
Provision 0060
Raite
Thomson
0051
RCA
0035
REC
0052, 0053
RedStar
0078
0203, 0206, 0207, 0208, 0242,
0066
Tokai
Amstrad 0044, 0071, 0078, 0090, 0092, 0096,
0058
0101, 0106, 0123, 0127, 0128,
0155, 0222, 0225, 0274, 0275,
0010, 0011, 0093, 0094, 0095,
0278, 0317, 0388, 0405,
0096, 0097, 0098, 0099, 0102,
Amstrad 0435
0115, 0162, 0167, 0191, 0331, 0332
Anglo 0123
0051, 0066
Ankaro 0005, 0010, 0069, 0072, 0108, 0115,
Toshiba 0013, 0049, 0100, 0142, 0161, 0190,
0123
0126
0211, 0212, 0218, 0218, 0220,
Anttron
Revoy 0061
0234, 0235, 0264, 0265, 0281
Apollo 0002
Reoc
0002, 0005, 0068, 0087
Roadstar 0004, 0052, 0060
TruVision 0062
Rowa 0050, 0144
Vtrek 0065
Rownsonic 0058
Wharfedale 0027, 0055, 0126
Armstrong 0105, 0225
Saba
Arcon 0008, 0009, 0026, 0094, 0222, 0280,
0405
Wintel 0056
ASA
0079
Sabaki 0126
Xbox 0102 ,0115
Asat
0043, 0105
Sampo 0036
Xenon 0334
ASLF
0123
Samsung 0018, 0196, 0205, 0210, 0227,
Xlogic 0126
AST
0014, 0074
0241, 0259, 0270, 0272, 0283,
XMS
Astacom 0095, 0122
0287, 0299, 0322, 0339, 0340
Yakumo 0144
Aston 0053, 0271
Sansui 0055, 0126
Yamada 0144
Astra
Sanyo 0257, 0262, 0285, 0298
Yamaha 0015, 0038, 0131, 0143, 0158, 0184,
0115, 0132
0052
ScanMagic 0256
Schneider 0004, 0005, 0006, 0024
Scott
0069, 0118
SEG
0004, 0042, 0051, 0126, 0152
Sharp 0022, 0044, 0130, 0151, 0268, 0280,
0350
Sherwood 0041
2
Downloaded
From TV-Manual.com Manuals
0271, 0307
0012, 0013, 0037, 0064, 0076, 0082,
0119, 0123, 0225
Astro 0005, 0006, 0010, 0017, 0066, 0087,
0108, 0113, 0114, 0115, 0116,
0119, 0283, 0392
AudioTon 0005, 0025, 0087
Aurora 0126
Austar 0126, 0157
Avalon 0078
Axiel
0122
Daewoo 0123, 0188
Fidelity 0071, 0090, 0116, 0275, 0405
Axis
0010, 0013, 0021, 0077, 0082, 0108,
Dansat 0007, 0061, 0068
Finlandia 0003, 0064
D-Box 0103
Filmnet 0433
Barcom0009
DDC
Filmnet Cablecrypt 0411, 0427
Best
Decca 0023
Filmnet Comcrypt 0411
Blaupunkt 0017, 0066, 0113
Delega 0004
Finlux 0003, 0030, 0064, 0080, 0084, 0292,
Blue Sky 0123, 0128
Dew
Boca
Diamond 0024
Finnsat 0021, 0055
0115, 0405
0009, 0010, 0108, 0115
0037, 0059, 0085, 0091, 0123, 0222,
0004, 0107
0363, 0413
0021, 0077
Digiality 0119
Flair Mate 0123
Boston 0122, 0222
Digipro 0129
Foxtel 0126, 0131, 0157, 0435
Brain Wave 0019, 0075, 0094
Discoverer 0112, 0118
Fracarro 0045, 0102
Brandt 0049, 0334, 0335, 0336
Discovery 0122
France Satellite/TV 0028
Broadcast 0018, 0076
Diseqc 0122
France Telecom 0429, 0434
Broco 0082, 0123
Diskxpress 0009, 0284
Freebox 0210
BSkyB 0101, 0155, 0183, 0216
Distratel 0128
Freecom 0002, 0032, 0113, 0116
BT
Distrisat 0105
Freesat 0089, 0127
BT Satellite 0049, 0095, 0277
Ditristrad 0025
FTE
Bubu Sat 0123
DNR
0094
FTEmaximal 0115, 0123
Bush
DNT
0016, 0043, 0078, 0105
Fuba
0225, 0237, 0242, 0251
0122
0003, 0007, 0020, 0031, 0045, 0061,
0068, 0107, 0200, 0207
BVV
0094
Cabletime 0406, 0407, 0408, 0424, 0426,
0008, 0034, 0085, 0091, 0108, 0277
0002, 0009, 0010, 0012, 0016, 0017,
0028, 0030, 0043, 0064, 0078,
Dong Woo 0036
0108, 0110, 0113, 0115, 0323
Drake 0026, 0327
DStv
0126
Fugionkyo 0129
Dune 0108, 0115
Galaxi 0009
Cambridge 0091, 0116
Dynasat
Galaxis 0005, 0010, 0013, 0021, 0025, 0031,
Canal Satellite 0073, 0109, 0114
Echostar 0016, 0052, 0078, 0102, 0109, 0123,
0428
0121
Canal+ 0047, 0115
0132, 0279, 0286, 0287, 0288,
Channel Master 0004, 0107
0294, 0342, 0343, 0344, 0345
Chaparral 0040
Einhell 0002, 0005, 0071, 0072, 0116, 0123,
0222, 0225, 0275
Cherokee 0122, 0132
0110, 0115, 0126, 0157, 0293,
0295, 0346
Galaxisat 0074
Gardiner 0124
GEC
0409
Chess 0052, 0112, 0118, 0123, 0322
Elap
CityCom 0003, 0022, 0098, 0110, 0119,
Elekta 0006
General Instrument 0425, 0432
Elsat
0092, 0123
GMI
Elta
0002, 0010, 0025, 0043, 0105, 0108,
Goldbox 0073, 0109, 0114
0124, 0157
Clatronic 0019, 0075
0122, 0123
0050, 0072, 0077, 0082, 0108,
Clemens Kamphus 0033
0115
Goldstar 0032
0002
Gooding
Clyde Cablevison 0409
Emanon
CNT
Emme Esse 0010, 0020, 0033, 0102, 0108,
0006
0115, 0121
Colombia 0222
0225
Granada 0064
Grandin 0062, 0111
Columbia 0222
Engel
Columbus 0028
Ep Sat 0003
Grothusen 0002, 0032
Comag 0222
Eurieult 0111, 0127, 0128
Grundig 0003, 0005, 0017, 0020, 0044,
Comcrypt 0433
Eurocrypt 0064
0054, 0065, 0066, 0097, 0101,
Commander 0069
Eurodec 0055
0106, 0113, 0116, 0117, 0126,
Commlink0005, 0072
Europa 0069, 0085, 0105, 0105, 0119
0128, 0155, 0166, 0167, 0169,
Comtec
0021, 0072, 0077
Europhon 0119, 0222
0175, 0282, 0298, 0325, 0388,
Condor
0010, 0108, 0115, 0119
Eurosat 0225
Connexions 0016, 0078, 0108, 0115, 0284
0123
0117, 0412
Goodmans 0003, 0031, 0186, 0195
Eurosky
Conrad 0084, 0085, 0108, 0110, 0115, 0116,
0119, 0222
G-Sat 0068
0119, 0222, 0225
Hanseatic 0039, 0086, 0118
Eurostar 0104, 0110, 0119, 0121, 0124,
Conrad Electronics 0119, 0123
0393, 0405, 0412
0010, 0108, 0110, 0115, 0116,
Haensel & Gretel 0119, 0222
0225
Hantor 0002, 0019, 0036, 0075
0123
Hanuri 0006
Contec 0021, 0022, 0077, 0085
Eutelsat
Cosat 0025
Eutra
Crown 0225
Exator 0002, 0005, 0087
Hauppage 0179, 0198
Cryptovision 0410
Fenner 0112, 0115, 0118, 0123
Heliocom 0008, 0119
Cybermax 0057
Ferguson 0003, 0007, 0020, 0055, 0061,
Helium 0119
0089
Daeryung 0016
Downloaded From TV-Manual.com Manuals
0068, 0182, 0289, 0290, 0291, 0391
Hase & Igel 0094
Hinari 0004, 0068, 0107
3
Lennox 0025
Mnet
0081, 0084, 0113, 0115, 0116,
Lenson
Morgan Sydney 0056
0119, 0122, 0127, 0165, 0322,
Lexus 0105
0323, 0328, 0389, 0413
LG
0032
0019, 0075
Life
0050
0003, 0020, 0212, 0313
Lifesat 0010, 0039, 0050, 0052, 0057, 0086,
Hirschmann 0017, 0033, 0066, 0078, 0079,
Hisawa
Hitachi
0029, 0116
0427, 0433
Morgan’s 0037, 0043, 0085, 0091, 0105,
0123, 0222, 0225
Motorola 0125
Movie Time 0419
0222
0108, 0112, 0115, 0118, 0123,
Mr Zapp 0434
Houston 0025, 0069
0222, 0297, 0303, 0347, 0372
Multichoice
HNE
Humax
0157, 0161, 0163, 0190, 0215,
Lifetec 0010, 0039, 0050, 0052, 0057, 0297,
0303, 0347, 0372
0217, 0296, 0346
Huth
Multitec 0052, 0112, 0347
Lorenzen 0069, 0094, 0096, 0119, 0222
Muratto 0015, 0032, 0074
0069, 0072, 0075, 0076, 0077,
Lorraine 0032
Mysat 0123
0085, 0119, 0130, 0222, 0225, 0272
Lupus 0010, 0108, 0115
Navex 0019, 0075
Luxor 0064, 0084, 0103, 0106, 0116, 0275,
NEC
0005, 0018, 0019, 0021, 0025, 0033,
Hypson0111
0313, 0323, 0388
ID Digital 0157
Imex
0054, 0126, 0433
Multistar 0034, 0036
0111
Lyonnaise 0055
0041, 0067, 0302
Network 0068
Neuhaus
0013, 0025, 0029, 0069, 0082,
0085, 0094, 0116, 0119, 0123
Imperial 0031, 0045
M & B 0086, 0118
Ingelen 0127
Macab 0055, 0434
Neusat 0094, 0123
Innovation 0010, 0039, 0050, 0052, 0057,
Manata 0095, 0111, 0122, 0123, 0222
NextWave 0051, 0130, 0273
Manhattan 0003, 0006, 0020, 0025, 0095,
Nikko 0123, 0225
0297, 0303, 0347, 0372
0122, 0269, 0383
Inernational 0222
Nokia 0003, 0020, 0064, 0079, 0084, 0103,
Interstar 0129
Marantz 0043
0114, 0156, 0170, 0196, 0221,
Intertronic 225
Mascom 0006, 0081
0233, 0235, 0241, 0253, 0254,
Intervision 0025, 0088, 0119
Maspro 0003, 0020, 0040, 0063, 0066, 0089,
0257, 0262, 0263, 0264, 0265,
0332, 0333, 0396, 0400, 0413
0328, 0393, 0412
0103, 0284, 0313, 0323, 0413
Jerrold 0414, 0420, 0422, 0425, 0432
0284, 0310, 0311, 0320, 0323,
0094, 0113, 0117, 0123, 0289,
ITT/Nokia0003, 0020, 0064, 0079, 0084,
Matsui
0049, 0066, 0095, 0107, 0113, 0117,
0122, 0412
Johansson 0019, 0075
JOK
0093, 0095, 0122
Max
0119
JSR
0025
MB
0039, 0086, 0118
JVC
0117, 0186, 0412
Nomex 0058
Nordmende 0002, 0003, 0004, 0006, 0055,
0075, 0107, 0290, 0324, 0391
Noos 0434
Mediabox 0073, 0109, 0114
Nova
Kamm 0123
Mediamarkt 0225
Novis 0019, 0075
Kathrein 0017, 0022, 0034, 0040, 0043, 0066,
Mediasat
Oceanic 0024
0113, 0122, 0123, 0124, 0132,
0013, 0073, 0082, 0109, 0114,
0116
0081, 0087, 0098, 0105, 0110,
Medion 0010, 0039, 0050, 0052, 0057, 0108,
0126
Octagon 0002, 0005, 0021, 0077, 0087
Okano 0033, 0034, 0225
0152, 0157, 0159, 0160, 0189,
0115, 0123, 0222, 0297, 0303,
Ondigital 0070, 0386, 0387
0218, 0283, 0299, 0300, 0324,
0335, 0347, 0372
Optex 0022, 0025
Medison 0123
Optus 0114, 0126, 0130
Kathrein Eurostar 0110
Mega
Orbit 0014
Key West 0222
Melectronic 0124
Klap
0122
Metronic 0002, 0005, 0006, 0009, 0062,
Konig 0119
0072, 0087, 0098, 0111, 0123,
Osat
Kosmos
0124, 0128, 0359, 0366, 0367,
Otto Versand 0017
0368, 0369, 0382
Pace
0362, 0371, 0381, 0392, 0395
KR
0043, 0105
0032, 0033, 0034, 0081
0005, 0087, 0089
Orbitech 0002, 0083, 0085, 0112, 0114,
0116, 0390
0005, 0106, 0388
0003, 0007, 0017, 0020, 0031, 0044,
0061, 0068, 0070, 0101, 0122,
Kreiselmeyer 0017, 0066, 0113
Metz
K-SAT 0123
Micro Electronic 0116, 0119, 0123
0132, 0155, 0183, 0199, 0201,
Kyostar 0002, 0087, 0222
Micro Technology 0082, 0123
0202, 0203, 0205, 0289, 0301,
L&S Electronic 0115, 0222
Micromaxx 0010, 0039, 0050, 0052, 0057,
Lasat
0017, 0066, 0113
0115, 0297, 0303, 0347, 0372
0006, 0010, 0035, 0036, 0037, 0077,
0091, 0108, 0110, 0112, 0115,
Microstar 0010, 0039, 0050, 0052, 0057,
0297, 0303, 0347, 0372
0119, 0222, 0334, 0335, 0336
0307, 0329, 0394
Pacific
0024
Packsat 0122
Palcom
0004, 0012, 0028, 0029, 0107
Lemon 0094
Microtec 0123
Palladium 0116, 0117, 0225, 0412
Lenco 0002, 0032, 0038, 0069, 0082, 0094,
Minerva
Palsat 0112, 0116
0108, 0110, 0115, 0119, 0123, 0277
Leng
0019
0017, 0117, 0412
Mitsubishi 0003, 0017, 0049
Paltec 0012
Mitsumi 0037
Panasat 0120, 0126
4
Downloaded
From TV-Manual.com Manuals
Panasoic 0003, 0020, 0044, 0101, 0155, 0192,
0318
Panda
Sat Team 0123
Start Trak 0002
Satcom 0018, 0039, 0076, 0086, 0118, 0119,
Strong 0002, 0005, 0010, 0032, 0045, 0108,
0114, 0115, 0126, 0129, 0231,
0306
0003, 0007, 0061, 0064, 0113, 0119
0232, 0234, 0238, 0243, 0245,
Patriot 0122, 0222
Satec
Phoenix 0021, 0031, 0068, 0077
Satelco 0108, 0115
Phonotrend 0003, 0005, 0025, 0033, 0072,
Satford 0018, 0076
STVO 0111
Satline
Sumida 0225
0346
Pioneer 0109, 0114, 0197, 0373, 0405, 0415,
0416
0020, 0068, 0123
0088
0253, 0266, 0284
Satmaster 0018, 0076
Sunny Sound 0108, 0115
SatPartner 0002, 0005, 0006, 0019, 0032,
Sunsat 0082, 0123
0033, 0075
Polsat 0055
Sunstar 0037, 0108, 0115, 0222, 0225, 0307
Polytron 0022
Satplus
0112
Super Sat 0121
Predki 0019, 0075
Schacke 0087
Supermax 0130
Preisner 0078, 0085, 0091, 0222
Schneider 0010, 0050, 0052, 0057, 0097,
Systec 0222
0112, 0122, 0285, 0303, 0347, 0385
Premiere 0025, 0047, 0073, 0109, 0114,
0157, 0253, 0254, 0266
Schwaiger 0022, 0024, 0039, 0051, 0068,
Tandberg 0055
Tandy 0005
Priesner 0225
0085, 0086, 0112, 0118, 0119,
Tantec 0003, 0020, 0028, 0029, 0289
Profile 0038, 0122
0128, 0222, 0272, 0299, 0305,
Tatung 0023
Promax0003
0335, 0337, 0339, 0340, 0341,
TCM
Prosat 0004, 0005, 0031, 0045, 0072, 0088,
0346, 0347, 0357, 0370, 0383, 0385
0010, 0039, 0050, 0052, 0057, 0133,
0134, 0135, 0136, 0137, 0138,
Scientific Atlanta 0417, 0418
0139, 0140, 0141, 0142, 0143,
Prosonic 0096
SCS
0144, 0145, 0146, 0147, 0148,
Protek 0024
Sedea Electronique 0129, 0222
Provision 0006
Seemann 0013, 0016, 0082, 0108, 0225
Techniland 0018, 0076
PVP Stereo Visual Matrix 0422
SEG
TechniSat 0016, 0029, 0060, 0083, 0105,
0107, 0270
Pye
0110
0002, 0010, 0019, 0039, 0075, 0086,
0117
Quadral 0004, 0005, 0010, 0072, 0085, 0088,
0095, 0107, 0108, 0115, 0122, 0132
0297, 0303, 0347, 0372
0096, 0108, 0115, 0118, 0139,
0112, 0114, 0116, 0150, 0151,
0229, 0231, 0234, 0250, 0258,
0164, 0185, 0194, 0213, 0214,
0317, 0384
0220, 0224, 0226, 0236, 0239,
0240, 0260, 0267, 0308, 0309,
Quelle 0017, 0071, 0110, 0119, 0275
Seleco
Quiero 0055
Septimo 0128
Radiola 0043, 0105
Servi Sat 0111, 0123
Technology 0126
Radix 0016, 0078, 0089, 0127, 0191, 0247,
Siemens 0017, 0066, 0091, 0113
Technosat 0130
Silva
Technowelt 0119, 0128, 0222
0256, 0380, 0397, 0399
0025, 0102
0032
0390, 0398
Rainbow 0005, 0087, 0089
Skantin 0123
Teco
Rediffusion 0041
Skardin 0013, 0082
Tele+1 0411, 0427, 0433
Redpoint 0013, 0082
Skinsat 0116
Telanor 0004
RedStar 0010, 0108, 0115
SKR
0123
Telasat
RFT
SKY
0125
Teleciel 0087
0005, 0043, 0069, 0072, 0083, 0105
0037, 0225
0039, 0086, 0110, 0118, 0119
Roadstar 0123
Sky Digital 0044
Telecom 0123
Roch
Skymaster0005, 0039, 0052, 0072, 0086,
Teledirekt 0068
0111
Telefunken
0002, 0020, 0049, 0095, 0122,
Rover 0088, 0115, 0123
0088, 0104, 0112, 0118, 0123,
Ruefach 0038
0139, 0149, 0158, 0219, 0227,
0330, 0334, 0335, 0336
Saba
0006, 0020, 0045, 0068, 0093, 0094,
0246, 0249, 0255, 0268, 0321,
Teleka 0005, 0016, 0078, 0081, 0087, 0094,
0095, 0110, 0119, 0122, 0128,
0322, 0347, 0348, 0349, 0350,
0270, 0289, 0290, 0319, 0326,
0351, 0352, 0374
0116, 0119, 0225, 0280, 0393
Telemaster 0006
Skymax 0043, 0105
Telemax 0035
Sabre 0003
SkySat 0112, 0116, 0118, 0119, 0123
Telepiu 0427, 0433
Sagem 0055, 0099, 0434
Skyvision 0025
Telesat 0039, 0086, 0118, 0119
Sakura 0021, 0031, 0077
SL
Telestar 0029, 0112, 0114, 0116
Salora 0041, 0064, 0302, 0307
SM Electronic 0112, 0123
Teletech 0104
Samsung 0002, 0153, 0154, 0162, 0193, 0204,
Smart 0110, 0123, 0127, 0222
Televes 0003, 0056, 0222, 0365
Sony
0044, 0114, 0276
Telewire 0025
SR
0037, 0222, 0225, 0290
Tempo
0334, 0337, 0338, 0339, 0340, 0391
0280
SAT
0004, 0014, 0015, 0074, 0090, 0116,
0405
0094, 0222
Starcom 0432
Sat Cruiser 0130
Starland 0052, 0123
Sat Partner 0116
Starring0019, 0075
Downloaded From TV-Manual.com Manuals
0130
Tevion 0010, 0039, 0050, 0052, 0057, 0123,
0297, 0303, 0347, 0372
5
Thomson 0003, 0011, 0027, 0046, 0049,
Wisi
0228, 0230, 0235, 0236, 0242, 024,
LG
0024, 0098, 0099, 0117, 0118, 0119,
0055, 0073, 0110, 0114, 0119,
0248, 0252, 0259, 0261, 0262,
0122, 0123, 0168, 0172, 0173,
0312, 314, 0315, 0316, 0356, 0375,
Magnavox 0127
0376, 0377, 0378, 0379
Mustek
0177, 0178, 0180, 0181, 0290,
0330, 0391, 0401, 0402, 0403, 0404
Wittenberg 0405
0207, 0314
0012
Panasonic
Woorisat
Thorn 0003, 0007, 0020, 0289, 0291
World 0075
0076, 0077, 0147, 0148, 0149,
Tioko 0022, 0222
Worldsat 0122
0158, 0159, 0160, 0171, 0172,
Tokai
Xrypton 0108, 0115
0173, 0174, 0177, 0189, 0190,
Tonna 0003, 0018, 0025, 0076, 0116, 0123
Xsat
0191, 0195, 0196, 0236, 0237,
Torx
0432
Zaunkonig 0094
TPS
0048
Zehnder 0006, 0009, 0010, 0015, 0034,
Triad
0014, 0015, 0032, 0074, 0312
0105
0006
0010, 0011, 0019, 0035, 0036,
Thorens 0024
0037, 0038, 0039, 0042, 0075,
0123, 0132
0074, 0096, 0098, 0108, 0110,
0286, 0287, 0297, 0298, 0299,
0300, 0301, 0302, 0315, 0318
Pioneer
0025, 0084, 0085, 0138, 0139,
Triasat 0030, 0080, 0116
0115, 0124, 0171, 0219, 0299,
0209, 0210, 0226, 0227, 0249,
Triax
0317, 0381, 0382
0282, 0283, 0284, 0285, 0292,
0017, 0029, 0080, 0110, 0116, 0123,
0222, 0334, 0364
Zenith 0125
0293, 0294, 0310, 0316, 0317
Turnsat 0123
Zinwell 0157
Saba
Tvonics 0182
Zodiac 0005, 0087
Samsung
0101, 0102
UEC
0126, 0131
Uher
0112
Sanyo 0014, 0016, 0082, 0083, 0167
Sharp 0068, 0069, 0070, 0132, 0133, 0134,
HTS Codes
0155, 0181, 0182, 0230, 0238,
Uniden 0042, 0090
Unisat 0021, 0077, 0105, 0222, 0225
0017, 0088, 0089, 0250, 0251,
0252
Twinner 0056, 0111, 0123, 0222, 0365
Philips
0239, 0303, 0304
0000, 0002, 0003, 0004, 0009,
Sony
0006, 0013, 0021, 0029, 0040, 0043,
Unitor 0009, 0019
0020, 0027, 0030, 0031, 0032,
United Cable 0422
0033, 0034, 0052, 0062, 0063,
0049, 0050, 0051, 0116, 0120,
Universum
0064, 0065, 0066, 0067, 0071,
0122, 0123, 0124, 0140, 0141,
0110, 0113, 0117, 0119, 0292,
0078, 0079, 0080, 0081, 0121,
0142, 0143, 0144, 0145, 0146,
0412, 0413
0127, 0161, 0176, 0272, 0273,
0156, 0157, 0175, 0184, 0185,
Variosat 0017, 0066, 0113
0274, 0275, 0276, 0277, 0278,
0186, 0187, 0188, 0192, 0193,
Vega
0279, 0280, 0281, 0295, 0296,
0197, 0198, 0205, 0206, 0207,
0308, 0309, 0312, 0313
0208, 0217, 0218, 0228, 0229,
0017, 0066, 0079, 0090, 0096,
0115
Ventana 0043, 0105
Vestel
0234, 0234, 0255, 0256, 0257,
0096
0260, 0261, 0269, 0270, 0271,
Via Digital 0046
Viasat 0132
Aiwa
Videoway 0423
0163, 0168, 0169, 0170, 0199,
Visionic 0019, 0025, 0052, 0053, 0093, 0122,
0123, 0353, 0354, 0355, 0356
0100
Denon 0058, 0059, 0060, 0061, 0072, 0073
Visiosat122, 140, 156
Denver
Viva
DK digital
0007
Eltax
Vivid
Goodmans 0103, 0104
0005
Vortec 0002, 0070, 0280
Harman/Kardon 0045
V-Tech 0014, 0015, 0074, 0093, 0098, 0124,
Hitachi
0304, 0313
Wela
0022, 0041, 0095, 0096, 0097
JVC 0008, 0015, 0044, 0055, 0056, 0057,
0085
0125, 0126, 0128, 0129, 0150,
Welltech 0112
0151, 0164, 0165, 0183, 0211,
WeTeKom 0112, 0116, 0118
0212, 0213, 0219, 0220, 0221,
Wevasat 0003
0222, 0223, 0224, 0225, 0231,
Wewa 0003
0232, 0233, 0240, 0241, 0242,
Winersat
0019, 0075
Wintergarten 0072
Wisi
0001, 0046, 0107, 0108, 0109, 0110,
Teac
0053, 0054, 0267, 0268
0111, 0112, 0113, 0114, 0115, 0116
Technics 0035, 0047, 0048, 0074, 0152, 0153,
0154, 0166, 0171, 0246, 0247, 0248
0028, 0086, 0087, 0105, 0106
Vivanco0059
0131
TCM
0200, 0201, 0288, 0289, 0290, 0291
Alba
Visiopass 0413, 0429, 0434
0069
0305, 0306, 0311
0023, 0043, 0090, 0091, 0092, 0162,
0262, 0263, 0264, 0265, 0266
Kenwood 0018, 0094, 0155, 0194, 0202,
0003, 0014, 0015, 0016, 0017, 0066,
0074, 0078, 0085, 0093, 0113,
0116, 0119, 0143, 0148, 0223,
6
Downloaded
From TV-Manual.com Manuals
0203, 0204, 0214, 0215, 0216,
0230, 0243, 0244, 0245, 0253, 0254
Thomson
0130, 0131, 0135, 0136, 0137,
0175, 0178, 0179, 0180, 0205
Yamaha 0026, 0093, 0258, 0259
Downloaded From TV-Manual.com Manuals
Contact information
Type no.
Product no.
België / Belgique
078 250 145
€0.06/min
Italia
8403 20086
€0.08/min
Svenska
08 5792 9100
Local
Danmark
3525 8759
Local
Luxembourg
40 6661 5644
Locale
Suomi
09 2311 3415
Local
Deutschland
01803 386 852
€0.09/min
Nederland
0900 8407
€0.10/min
United Kingdom
0870 900 9070
France
0821 611 655
€0.09/min
Norge
2270 8111
Local
E§§A™
0 0800 3122 1280 ¢ˆÚ¿Ó
Österreich
0810 000205
€0.07/min
España
902 888 784
€0.10/min
Portugal
2 1359 1442
Ireland
01 601 1777
Local
Schweiz / Suisse / Svizzera
0844 800 544
Local
Local
Local
Printed in Belgium
Downloaded From TV-Manual.com Manuals