NEVER Operate:
●Without first viewing owner's manual and quick start guide.
●With more than one passenger.
●On hills steeper than 15 degrees
●On public roads
●On paved surfaces-pavement may seriously affect handling and control.
●With Non-CFMOTO approved accessories.
ALWAYS:
●Keep hands and feet inside vehicle.
●Reduce speed and use extra caution when carrying a passenger.
●Operate slowly in reverse-avoid sharp turns or sudden braking.
●Make sure passenger reads and understands all safety labels
●Watch for branches or other hazards that could enter vehicle.
G
Locate and Read Owner's manual, Follow all INSTRUCTIONS and WARNINGS. If Owner'
s manual is missing, contact a CFMOTO dealer for replacement.
Read, understand, and follow all of the instructions and safety precautions in
this manual and on all product labels. Failure to follow the safety precautions
could resullt in serious injury or death.
The engine exhaust gas from this product contains CO, which is deadly gas and
could cause headache, giddy, disgusting or lose consciousness, even death.
Instructions
Thank you for purchasing a CFMOTO vehicle, and welcome to our worldwide family of CFMOTO owners.
We proudly produce an exciting line of utility and recreational products.
●All terrain vehilce (ATV)
●Utility vehicle (patrol, forest protecting and hunting)
●Motorcycles
CFMOTO, a company which is specialized in production of liquid-cooled engine, is the top- level supplier
in China. Compared to same displacement of air-cooled engine, engine cooling effect is better, oil
temperature can be adjusted more freely, more powerful and lower fuel consumption, longer engine
working life.
For safe and enjoyable operation of your vehcile, be sure to follow the instructions and recommendations in this owner's manual. Your manual contains instructions for minor maintenance, but
informations about major repairs is outlined in the CFMOTO service manual and should be performed
only by CFMOTO service dealer and technician.
Your CFMOTO dealer knows your vehicle best and is interested in your total satisfaction. Be sure to
return to your dealerhship for all of your service.
Due to constant improvements in the design and quality of production components,
some minor discrepancies may result between the actual vehicle and the information
presented in this publication. Depictions and/or procedures in this publication are
intended for reference use only.
Table of Contents
VIN No.…………………………………………………………………………………… 2
Safety……………………………………………………………………………………………… 3
Features and Controls………………………………………………………………………… 31
Operation……………………………………………………………………………………… … 51
Emission control systems……………………………………………………………………… 71
Maintenance……………………………………………………………………………………… 72
Specification…………………………………………………………………………………… 120
Troubleshooting…………………………………………………………………………………123
Circuit layout…………………………………………………………………………………… 128
-1-
Vehicle Identification Number
Record your vehicle's identification number and engine serial number in the spaces provided, remove
“ignition” key and store it in a safe place for duplicating spare key if keys are lost, otherwise ignition
key can only be replaced.
① Vehicle Identification No.:
② Engine Serial No.:
-2-
SAFETY
Rider Safety
The following signals or symbols appear throughout this manual and on your vehicle. Your safety is
involved when words or symbols are used. Become familiar with these meanings before reading the
manual.
The safety alert warning indicates a potential hazard that may result in serious injury or death.
CAUTION
A caution indicates a situation that may result in damage to your vihicle.
NOTE
A note alert you to important informations or instructions.
-3-
Safety Decals and Locations
Warning decals have been placed on your vehicle for your protection.
Read and follow the instructions of the decals on the vehicle very
carefully. If any of the decals depicted on the vehicle in this manual
differ from the decals on your vehicle, always read and follow the
instrctions of decals on your vehicle.
①Cargo box warning② Towing load waring
Warning
●Passengers can be thrown off. This can cause
serious injury or death.
●Never carry passengers in cargo box.
●Max. load of cargo box:100kg
●Towing bracket veritcal load:50kg,Towing load:125kg(including cargo)
③ Tire pressure and overload warning
Improper tire, tire pressure or overloading can
cause loss of control resulting in SEVERE INJURY OR DEATH.
Tire pressure:PSI(kpa)
Front tire:10(70)Rear tire: 12(84)
Maximum weight capacity:
Including driver, passenger, cargo and accessories:250kg
Reduce speed and allow greater distance for braking when
Carrying cargo. Overloading or carrying tall, off-center or
Unsecured loads will increase your risk to control. Loads should be
centered and carried as low as possible in box. For stability on rough
or hill terrain, reduce speed and cargo. Be careful if load extends over
the side of box.
-4-
Safety Decals & Locations
Cab frame① warning
Warning
●ALWAYS WEAR YOUR SEAT BELT
and make sure passenger wears seat belt.
●VEHICLE OVERTURN can cause severe injury or death.
The cab frame is not designed or intended to rollover protection.
Shift caution
Caution
To avoid transmission damage, Shift only when vehicle is stationary or at idle.
When vehicle is stopped, place shift in the parked position.
Age warning
Warning
Operating this vehicle if you're under age of 16 increase your chance of
Severe injury or death. Never operating this vehicle under age 16 or without
valid driver's licence.
Overturn warning
Warning
Improper operation can cause this vehicle to overturn and lead to serious injury or death.
This vehicle handles differently than cars, trucks or other off-road vehicles. In order to avoid
oveturns
●Avoid sharp overturns
●Never turn when applying heavy throttle.
●Never make abrupt steering maneuvers.
●Operate at speeds appropriate for your skills, the conditions
And the terrain.
●DO NOT do power slides, “donuts”, jumps or other
Jumping stunts.
-5-
Safety Decals and Locations
Passenger safety warning①
Operation warning②
Warning
Never carry passenger under age 12
Never carry more than one passenger
Never ride after using drugs or alcohol
To reduce the risk of SEVERE INJURY or DEATH,
Never carry a passenger under age 12 or too small to
Firmly plant feet on the floor and securely grasp hand holds.
The passenger must always
●Wear seat belt.
●Use an approved helmet and protective gear.
●Securely grasp hand holds and plant feet firmly on the floor.
●Tell operator to slow down or stop if uncomfortable get-off
and walk if conditions require.
●Keep hands and feet inside vehicle at all times.
●Watch for branches, brush, and other hazards that could enter vehicle.
-6-
Safety decals and Locations
Pre-ride warning
① Driving warning
Always use approved helmet and protective gear for operator and passenger.
Never use with drugs or alcohol.
Improper vehicle use can result in SEVERE INJURY or DEATH.
Never operate:
●Without first reading and understanding of safety guide.
●With more than one passenger.
●On hilles steeper than 15 degrees.
●On paved surfaces-pavement may seriously affect handling
Or control.
●With Non-CFMOTO genuine parts or accessories. They may
seriously affect stability.
Always:
●Keep hands and feet inside vehicle.
●Reduce speed and use extra caution when carrying passenger
●Operate slowly in reverse- avoid sharp turns or sudden braking.
●Make sure passenger reads and understands all safety labels.
●Watch for branches or other hazards that could enter vehicle.
Locate and read owner's manual, follow all instructions and warnings. If owner's
Maunal is missing, contact CFMOTO dealer for detailed information.
-7-
Safety Warning and Locations
Pre-ride warning
①4WD operation warning
Must stop or at idle when changing
2WD and 4WD switch to avoid damage
of transmission parts
When Diff-lock is locked, it will enhance vehicle's
maneuverability, please keep low speed and
enough braking distance to avoid out of control.
②Air filter ventilator warning
●DO NOT cover air filter ventilator to avoid
damage of engine.
●Keep air entering through ventilator smoothly.
-8-
Rider safety
Failure to follow the warning contained in this manual can result in severe injury or death.
Your CFMOTO vehicle is not a toy and can be hazardous to operate. This vehicle handles
differently than cars, trucks or other off-road vehicles.A collision or rollover can occur quickly
even during routine maneuvers like turning, or driving on hilles or over obstacles if you take
improper precautions.
Read and understand your owner's manual and all warning before operating the vehicle.
Always heed the following instructions and procedures which are outlined further detailes
within your owner's manual.
●Read this manual and all labels carefully, following the operating procedures described.
●Never carry a passenger until you have operated this vehicle at least 2 hours and have completed the New
Operator Driving procedures outlined on pages 57-58.
●Operation is prohibited for anyone under 16 years of age or anyone without valid driving licence.
●Never carry a passenger under age 12. Make sure any passenger is tall enough to comfortably and safely
reach the hand holds and place both feet on the floor.
●Riders should wear seat belts at all times. Seat belts reduce the severity of injury in the event of sudden
stop or accident.
●Helmet and eye protection are required for both operator and passenger at all times.
●Always keep hands and feet inside vehicle.
●Never allow a passenger to ride in the cargo box. Never carry more than one passenger.
●Never permit a guest to operate this vehicle unless the guest has read this manual and all products label
and has completed the New Operator Driving procedures outlined on pages 58-59.
●To reduce tipover risk, be especially careful when encounting obstacles and slopes and braking on hills or
during turns.
●Never operate with Non-CFMOTO genuine accessries which may seriously affect vehicle's stability and
could cause the vhicle to overturn.
-9-
Rider safety
●This vehicle handles differently than cars, trucks or other off-road vehicles. Turning improperly can result in
an overturn. Avoid sharp turns. Never turn while applying heavy throttle. Never make abrupt steering maneuvers. Operate at speeds appropriate for your skills, the conditions and terrain.Do not do power slides,
“donuts”, jumps or other driving stunts.
●Never operate at excessive speeds. Always travel at speed appropriate for your skills, your passenger's
skills and operation conditions.
●This vehicle is for off-road only. Never operate on public roads and always avoid paved surfaces.
●Never use drugs or alcohol before or during driving.
●Always inpsect your vehicle before driving each time to make sure it's in safe operating condition. Always
follow the inspection and maintenance procesures and schedules described in this manual.
●Always keep both hands on the steering wheel during operation. A passenger should always be seated in
the passenger seat with both feet on the floor and both hands firmly grasping securely the hand holds.
●Always travel slowly and pay extra attention when driving on unfamiliar terrain. Be alert to changing terrain.
●Never operate on excessively rough, slippery and loose terrain.
●Always follow properly turning procedures described in this manual. Practice turning at low speeds before
attempt to faster turn at higher speeds.
●Always have this vehicle checked by authorized CFMOTO dealer if it has been involved in an accident.
●Always follow proper procedures for climbing hills as described in this manual. Check the terrain carefully
before attempt to climb a hill. Never climb hills with excessively slippery or loose surfaces. Never open
throttle suddenly or make sudden gear changes. Never go over the top of hill at high speeds.
-10-
Rider Safety
Always follow the proper procedures outlined in this manual for traveling downhill and for braking on
hills. Check the terrain carefully before descending a hill. Never travel downhill at high speed. Avoid going
downhill at an angle, which would cause the vehicle to lean sharply to one side. Travel straight down the
hill where possible.
Avoid crossing the side of a hill.
Always check for obstacles before operating in a new area. Never attempt to operate over large obstacles such as rocks or fallen trees. Always follow the proper procedures outlined in this manual when operating
over obstacles.
Always be careful of skidding or sliding. On slippery surfaces such as ice, travel slowly and exercise
caution to reduce the chance of skidding or sliding out of control.
Never operate in fast-flowing water or in water that exceeds the recommended maximum depth. See
page 65. Wet brakes may have reduced stopping ability. To dry out the pads, apply the brakes lightly several times while driving slowly.
Always be sure there are no obstacles or people behind your vehicle when operating in reverse. When
it's safe to proceed in reverse, move slowly. Avoid making sharp turns in reverse.
Always use the proper size and type of tires specified for your vehicle. Always maintain proper tire
pressure.
Never exceed the stated load capacity for this vehicle. Cargo should be properly distributed and securely
attached. Reduce speed and follow the instructions in this manual for hauling cargo or pulling a trailer. Allow
a greater distance for braking.
Always turn off the engine before refueling. Make sure the refueling area is well ventilated and free of
any source of flame or sparks. Gasoline is extremely flammable. See page 30 for fuel safety warnings.
Remove flammable material containers from the box before filling.
Always remove the ignition key when the vehicle is not in use to prevent unauthorized use or accidental
starting.
FOR MORE INFORMATION ABOUT SAFETY, please contact with your distributor.
-11-
Rider Safety
Modifications to your vehicle may negatively impact vehicle stability and result in serious injury
or death. Failure of critical machine components may result from operation with any modifications,
especially those that increase speed or power. This vehicle may become less stable at speeds
higher than those for which it is designed. Loss of control may occur at higher speeds.
Your vehicle vehicle is designed to provide safe operation when used as directed.
Do not make any modifications to this vehicle.
Never operate with accessories not approved by CFMOTO for use on this vehicle.
The operator must check all safety components before each ride.
Make sure your vehicle is in excellent operating condition at all times.
Equipment Modifications
We are concerned for the safety of our customers and for the general public. Therefore, we design accessories
for your vehicle that take into consideration safe vehicle handling and stability. Never operate with accessories not approved by CFMOTO for use on this vehicle. Non-approved accessories may seriously affect
vehicle stability and could cause the vehicle to overturn.
Do not install on a CFMOTO vehicle any equipment that may increase the speed or power of the vehicle,
or make any other modifications to the vehicle for these purposes. Any modifications to the original equipment
of the vehicle create a substantial safety hazard and increase the risk of bodily injury.
The warranty on your vehicle is terminated if any equipment has been added to the vehicle, or if any modifications have been made to the vehicle, that increases its speed or power.
NOTE: The addition of certain accessories, including (but not limited to) mowers, blades, tires, sprayers, or
large racks, may change the handling characteristics of the vehicle. Use only CFMOTO-approved accessories, and familiarize yourself with their function and effect on the vehicle.
-12-
Safe Riding Gear
Always wear appropriate clothing when riding a CFMOTO vehicle. Wear protective clothing for comfort and
to reduce the chance of injury.
Eye Protection
Long Sleeves
Gloves
Sturdy footwear
-13-
Long Pants
Helmet
Safe Riding Gear
Helmet
Wearing a helmet can prevent a severe head injury. Whenever riding this CFMOTO vehicle, always wear
a helmet that meets or exceeds established safety standards.
Approved helmets in the USA and Canada bear a U.S. Department of Transportation (DOT) label.
Approved helmets in Europe, Asia and Oceania bear the ECE 22.05 label and the E-Mark label.
Eye Protection
Do not depend on eyeglasses or sunglasses for eye protection. Whenever riding a CFMOTO vehicle,
always wear shatterproof goggles or use a shatterproof helmet face shield. CFMOTO recommends
wearing approved Personal Protective Equipment (PPE) bearing markings such as VESC or CE. Make sure
protective eye wear is kept clean.
Gloves
Wear gloves for comfort and for protection from sun, cold weather and other elements.
Boots
Wear sturdy footwear. Do not ride a CFMOTO vehicle with bare feet.
Clothing
Wear long sleeves and long pants to protect arms and legs.
-14-
Rider Safety
Age Restrictions
This vehicle is an ADULT VEHICLE ONLY. Operation is prohibited for anyone under 16 years of age or anyone
without a valid driver's license. Never operate with a passenger under the age of 12. Make sure any passenger is tall enough to comfortably and safely reach the hand holds and place both feet on the floor.
Know Your Vehicle
As the operator of the vehicle, you are responsible for your personal safety, the safety of others (including
your passenger), and the protection of our environment. Read and understand your owner's manual, which
includes valuable information about all aspects of your vehicle, including safe operating procedures.
We strongly advise you to strictly follow the recommended maintenance program outlined in your owner's
manual. This preventive maintenance program is designed to ensure that all critical components on your
vehicle are thoroughly inspected at specific intervals.
-15-
Rider Safety
Know Your Riding Area/Tread Lightly
Your CFMOTO vehicle is an off-road vehicle. Familiarize yourself with all laws and regulations concerning the operation of this vehicle in your area. Respect the environment in which you ride your vehicle. Find
out where the designated riding areas are by contacting your CFMOTO dealer, a local riding club, or
local officials.
Help keep our trails open for recreational vehicle use. Operate with respect for the terrain, avoid littering,
and always stay on the designated trails.
Trail Etiquette
Always practice good etiquette when riding. Allow a safe distance between your vehicle and other vehicles
operating in the same area.
Communicate to oncoming operators by signaling the number of vehicles in your group. When stopping,
move your vehicle to the edge of the trail as far as possible to allow others to pass safely.
-16-
Rider Safety
POTENTIAL HAZARD
Operating this vehicle without proper instruction
WHAT CAN HAPPEN
Loss of control and accident resulting in serious injury or death
HOW TO AVOID THE HAZARD
The risk of an accident is greatly increased if the operator does not know how to operate
the vehicle properly in different situations and on different types of terrain.
All operators must read and understand the owner's manual and all warning and instruction labels before
operating the vehicle.
POTENTIAL HAZARD
Turning improperly
WHAT CAN HAPPEN
Loss of control, accident or overturn resulting in serious injury or death
HOW TO AVOID THE HAZARD
Avoid sharp turns. Never turn while applying heavy throttle. Never make abrupt steering maneuvers.
Operate at speeds appropriate for your skills, the conditions and the terrain. DO NOT do power slides,
“donuts”, jumps or other driving stunts. Practice turning at slow speeds before attempting to turn at
faster speeds.
POTENTIAL HAZARD
Riding in this vehicle without wearing the seat belt
WHAT CAN HAPPEN
Serious injury or death in the event of an accident or sudden stop
HOW TO AVOID THE HAZARD
Always make sure the seat belts are secured for both the operator and passenger before riding.
-17-
Rider Safety
POTENTIAL HAZARD
Failure to follow the minimum age recommendations for this vehicle
WHAT CAN HAPPEN
Serious injury or death (the child or others)
HOW TO AVOID THE HAZARD
Operation is prohibited for anyone under 16 years of age or anyone without a valid driver's license. Never
operate with a passenger under the age of 12.
Make sure any passenger is tall enough to comfortably and safely reach the hand holds and place both feet
on the floor.
POTENTIAL HAZARD
Riding this vehicle without wearing an approved helmet and eye
protection
WHAT CAN HAPPEN
Head injury, eye injury or death in the event of an accident
HOW TO AVOID THE HAZARD
Operator and passenger:
Always wear an approved helmet that fits properly. Always wear eye
protection (goggles or face shield).
-18-
Rider Safety
POTENTIAL HAZARD
Riding this vehicle after consuming alcohol or drugs
WHAT CAN HAPPEN
Accident resulting in serious injury or death due to affected judgment,
balance and perception and slower reaction time
HOW TO AVOID THE HAZARD
Never consume alcohol or drugs before or while riding this vehicle.
POTENTIAL HAZARD
Removing hands from the steering wheel or hand holds or removing feet from the floor while riding
WHAT CAN HAPPEN
Loss of control and accident resulting in serious injury or death
HOW TO AVOID THE HAZARD
The operator should always keep both hands on the steering wheel during operation. A passenger should
securely grasp the hand holds and plant both feet firmly on the floor.
POTENTIAL HAZARD
Failure to inspect the vehicle before operating
Failure to properly maintain the vehicle
WHAT CAN HAPPEN
Accident, equipment damage
HOW TO AVOID THE HAZARD
Always inspect your vehicle before each use to make sure it's in safe
operating condition.
Always follow the inspection and maintenance procedures and schedules
described in the owner's manual.
-19-
Rider Safety
POTENTIAL HAZARD
Using accessories not approved by CFMOTO for use on this vehicle
WHAT CAN HAPPEN
Loss of control, accident or overturn resulting in serious injury or death
HOW TO AVOID THE HAZARD
Never operate with accessories not approved by CFMOTO for use on this vehicle. Non-approved accessories may seriously affect vehicle stability.
POTENTIAL HAZARD
Operating this vehicle on paved surfaces, including sidewalks, paths, parking lots, and driveways
WHAT CAN HAPPEN
Loss of control and accident resulting in serious injury or death
HOW TO AVOID THE HAZARD
This vehicle's tires are designed for off-road use only, not for use on pavement. Paved surfaces may seriously
affect handling and control of the vehicle, and may cause the vehicle to go out of control.
Avoid operating the vehicle on pavement. If you must operate on a paved surface, travel slowly and do not
make sudden turns or stops.
POTENTIAL HAZARD
Operating this vehicle on public streets, roads or highways
WHAT CAN HAPPEN
Collision with another vehicle
HOW TO AVOID THE HAZARD
Never operate this vehicle on any public street, road or highway, including dirt or gravel.
In many areas it's illegal to operate vehicles of this type on public streets, roads and highways.
-20-
Rider Safety
POTENTIAL HAZARD
Improperly operating over obstacles
WHAT CAN HAPPEN
Loss of control or overturn resulting in serious injury or death
or death
HOW TO AVOID THE HAZARD
Before operating in a new area, check for obstacles.
Avoid operating over large obstacles such as rocks and fallen
trees when possible. If unavoidable, use extreme caution and
operate slowly.
POTENTIAL HAZARD
Skidding or sliding
WHAT CAN HAPPEN
Loss of control, accident or overturn resulting in serious injury or death
HOW TO AVOID THE HAZARD
Always follow proper procedures for operating on slippery surfaces as described in the owner's manual.
When operating on slippery surfaces such as ice or loose gravel, reduce speed and use extra caution to
reduce the chance of skidding or sliding out ofcontrol.
Do not operate on excessively slippery surfaces.
-21-
Rider Safety
POTENTIAL HAZARD
Operating through deep or fast-flowing water
WHAT CAN HAPPEN
Loss of traction, loss of control, overturn or accident resulting
in serious injury or death
HOW TO AVOID THE HAZARD
Always follow proper procedures for operating in water as described in the
owner's manual.
Never operate in fast-flowing water or in water that exceeds the
recommended maximum depth.
POTENTIAL HAZARD
Improperly operating in reverse
WHAT CAN HAPPEN
Collision with an obstacle or person, resulting in severe injury or death
HOW TO AVOID THE HAZARD
Always follow proper procedures for operating in reverse as described
in the owner's manual.
Before shifting into reverse gear, always check for obstacles or people
behind the vehicle. When it's safe to proceed, back slowly.
Avoid making sharp turns in reverse.
-22-
Rider Safety
POTENTIAL HAZARD
Overloading the vehicle or carrying/towing cargo improperly
WHAT CAN HAPPEN
Loss of control, accident due to instability and changes in vehicle
handling
HOW TO AVOID THE HAZARD
Always follow the instructions in the owner's manual for carrying
cargo or pulling a trailer.
Never exceed the stated load capacity for this vehicle.
Cargo should be properly distributed and securely attached.
Reduce speed when carrying cargo or pulling a trailer. Allow a
greater distance for braking.
POTENTIAL HAZARD
Operating this vehicle with improper tires or with improper or uneven
tire pressure
WHAT CAN HAPPEN
Loss of control, accident or overturn resulting in serious injury or death
HOW TO AVOID THE HAZARD
Always use the size and type of tires specified for your vehicle.
Always maintain proper tire pressure.
-23-
Rider Safety
POTENTIAL HAZARD
Climbing hills improperly
WHAT CAN HAPPEN
Loss of control or overturn resulting in serious injury or death
HOW TO AVOID THE HAZARD
Always follow proper procedures for climbing hills as described
in the owner's manual.
Always check the terrain carefully before ascending a hill.
Avoid climbing steep hills (15° maximum).
Use extreme caution when operating on hills, and follow proper
operating
procedures outlined in the owner's manual.
Never climb hills with excessively slippery or loose surfaces.
Never open the throttle suddenly.
Never go over the crest of a hill at high speed. An obstacle, a sharp
drop, or another vehicle or person could be on the other side of the hill.
POTENTIAL HAZARD
Traveling downhill improperly
WHAT CAN HAPPEN
Loss of control or overturn resulting in serious injury or death
HOW TO AVOID THE HAZARD
Always follow proper procedures for traveling down hills as described in the owner's manual.
Always descend a hill with the transmission in forward gear. Never descend a hill with the transmission in neutral.
Always check the terrain carefully before descending a hill.
Never travel down a hill at high speed.
Avoid traveling down a hill at an angle, which would cause the vehicle to lean sharply to one side. Travel straight
downhill
-24-
Rider Safety
POTENTIAL HAZARD
Crossing hills and turning on hills
WHAT CAN HAPPEN
Loss of control or overturn resulting in serious injury or death
HOW TO AVOID THE HAZARD
Avoid operating on steep hills (15° maximum).
Avoid crossing the side of a hill.
POTENTIAL HAZARD
Stalling, rolling backwards while climbing a hill
WHAT CAN HAPPEN
Loss of control or overturn resulting in serious injury or death
HOW TO AVOID THE HAZARD
Maintain a steady speed when climbing a hill.
If you lose all forward speed:
Apply the brakes gradually until the vehicle is fully stopped.
Place the transmission in reverse and slowly allow the vehicle
to roll straight downhill while applying light brake pressure to
control speed.
-25-
Rider Safety
POTENTIAL HAZARD
Operating on excessively rough, slippery .or loose terrain.
WHAT CAN HAPPEN
Loss of control, accident or overturn resulting in serious injury or death.
HOW TO AVOID THE HAZARD
o not operate on excessively rough, slippery .
POTENTIAL HAZARD
Operating this vehicle at excessive speeds
WHAT CAN HAPPEN
Loss of control and accident resulting in serious injury or death
HOW TO AVOID THE HAZARD
Operate at speeds appropriate for your skills, the conditions and the
terrain.
-26-
Rider Safety
POTENTIAL HAZARD
Attempting jumps and other stunts
WHAT CAN HAPPEN
Loss of control, accident or overturn resulting in
seriousinjury or death
HOW TO AVOID THE HAZARD
Never attempt jumps and other stunts.
Avoid exhibition driving.
POTENTIAL HAZARD
Operating on frozen bodies of water
WHAT CAN HAPPEN
Severe injury or death if the vehicle and/or riders
fall through the ice
HOW TO AVOID THE HAZARD
Never operate this vehicle on a frozen body of water.
-27-
Rider Safety
POTENTIAL HAZARD
Failure to use extra caution when operating this vehicle
on unfamiliar terrain
WHAT CAN HAPPEN
Loss of control or overturn resulting in serious injury or death
HOW TO AVOID THE HAZARD
Travel slowly and use extra caution when operating on
unfamiliar terrain.
Always be alert to changing terrain.
POTENTIAL HAZARD
Carrying a passenger in the cargo box
WHAT CAN HAPPEN
Serious injury or death due to a fall from the vehicle or contact
with moving .
components
HOW TO AVOID THE HAZARD
Never allow a passenger to ride in the cargo box.
-28-
Rider Safety
POTENTIAL HAZARD
Operating with more than one passenger
WHAT CAN HAPPEN
Loss of control and accident resulting in serious injury or death
HOW TO AVOID THE HAZARD
Never carry more than one passenger.
Additional passengers can affect the operator's ability to steer
and operate the controls.
Operating a damaged vehicle can result in an accident with serious injury or death. After any overturn or
accident, have a qualified
service dealer inspect the entire vehicle for possible damage, including (but not
limited to) brakes, throttle and steering systems.
Exhaust system components are very hot during and after use of the vehicle.
Hot components can cause serious burns and fire. Do not touch hot exhaust system components. Always
keep combustible materials away from the exhaust system. Use caution when traveling through tall grass,
especially dry grass.
Leaving the keys in the ignition can lead to unauthorized use of the vehicle resulting in serious injury or death.
Always remove the ignition key when the vehicle is not in use.
-29-
Rider Safety
Gasoline is highly flammable and is explosive under certain conditions.
Always exercise extreme caution whenever handling gasoline.
Always stop the engine when refueling.
Always refuel outdoors or in a well ventilated area.
Remove flammable material containers from the box before filling.
Do not smoke or allow open flames or sparks in or near the refueling area or where gasoline is stored.
Never refuel while a person is in the vehicle.
Do not over fill the tank. Do not fill the tank neck.
If gasoline spills on your skin or clothing, immediately wash it off with soap and water and change clothing.
Never start the engine or let it run in an enclosed area. Gasoline powered engine exhaust fumes are poisonous
and can cause loss of consciousness and death in a short time.
-30-
FEATURES AND CONTROLS
Component Locations
Your vehicle is equipped with cab nets on both sides of the vehicle. Cab nets must be used by both operator
and passenger at all times. Promptly replace worn or damaged parts with new one, available from your
authorized CFMOTO dealer.
NOTE: The vehicle illustrated below is shown without cab nets only to allow component identification.
cab frame
seat belt
cargo box
dash
seat
hip bar
fuel tank cap
-31-
shifter
passenge hand hold
Component Locations
storage compartment
radiator
winch Bracket
Steering wheel
Headlights
-32-
Component Locations
Taillight
Muffler
(spark arrestor)
Towing Bracket
Trailer Receiver Hitch Bracket
This vehicle is equipped with a receiver hitch bracket for a trailer hitch.
Trailer towing equipment is not supplied with this vehicle.
To avoid injury and possible damage, always heed the warnings and towing capacities outlined on pages 69-70.
-33-
Rear Service Panel
The rear service panel is located behind the seats on the frame of the vehicle. Remove the seats to access the
service panel. Remove the service panel to access serviceable engine components and clutches.
Seats
Before operating the vehicle, always push down on both seat backs to ensure the latches are secure.
Seat Adjustments
Loosen (do not remove) the four screws located on the seat bottom. Slide the seat forward or rearward to the
desired position. Tighten the four screws ,Torque:(8 Nm). Do not overtighten.
Seat Removal
1. Pull up on the seat latch lever located under the rear edge of the seat.
2. Tilt the seat forward.
3. Lift the seat upward to remove it from the vehicle.
Reverse this procedure to reinstall the seat. Make sure the front edge of
the seat is properly installed to the seat retainer bar. Press down firmly at
the rear of the seat to engage the rear latch.
Seat Latch
Front Seat Retainer
-34-
Steering Wheel
The steering wheel can be tilted upward or downward for rider preference.
Lift and hold the steering wheel adjustment lever while moving the steering
wheel upward or downward.
Release the lever when the steering wheel is at the desired position.
Adjustment
Lever
-35-
Front trunk
FEATURES AND CONTROLS
Remove the front panel and check the front trunk.
Detail messages about cubage of front trunk to
see the page 122.
Front panel
Konb
Front panel
1.Front trunk,radiator and secondary water tank under the
Front panel. Front panel need to be removed for inspection.
2.knob on the front panel,unscrew knob
3.Pull out the front panel by hold of the top panel
4.Remove the left panel.
Fuel cap
Front trunk
Fuel cap near the seat of passenger,
If refuel the 93# or more than. Don't refuel the fuel as low
93# fuel, Remove the inflammable material after refuel.
Fuel tank cap
-36-
Seat Belts
This vehicle is equipped with three-point lap and diagonal seat belts for the operator and passenger.
Riding in this vehicle without wearing the seat belt can result in serious injury or death in the event of an
accident or sudden stop. Always make sure the seat belts are secured for both the operator and passenger before riding.
To wear the seat belt properly, follow this procedure:
1. Pull the seat belt latch downward and across your chest
toward the buckle at the inner edge of the seat. The belt should
fit snugly across your hips and diagonally across your chest.
Make sure the belt is not twisted.
2. Push the latch plate into the buckle until it clicks.
3. Release the strap, it will selftighten.
Seat belt
hook
NOTE:
Press the red release latch on the buckle to release the seat belt.
Seat belt hook
-37-
Seat Belts
Seat Belt Inspection
Inspect all seat belts for proper operation before each use of the vehicle.
1. Push the latch plate into the buckle until it clicks. The latch plate must slide smoothly into the buckle. A click
indicates that it's securely latched.
2. Push the red release latch in the middle of the buckle to make sure it releases freely.
3. Pull each seat belt completely out and inspect the full length for any
damage, including cuts, wear, fraying, dirt, debris or stiffness. If any damage is found, have the seat belt
system checked and/or replaced by an authorized CFMOTO dealer.
switchs
4WD/2WD Ignitio n
switc h Dashboard flameout
SWITCH
switch tum
switch Auxiliary Outlet
Power-in creased switch
Horn switc h
high and low beam swi tch
light
switch
Danger lig ht
switc h
Time adj ust ment sw itch
-38-
Switches
Time adjustment switch
Near the dashboard, use for adjust the hour and minutes by operated the time adjustment switch. Hour by
Shortly pressed to adjust. Minute by long pressed to adjust.
Danger light switch
Front and rear turn light will be lighted when operate the danger light switch.meanwhile, danger light
instruction will be showed on the dashboard.
Ignition Switch
Leaving the keys in the ignition can lead to unauthorized use of the vehicle resulting in serious injury or death.
Always remove the ignition key when the vehicle is not in use.
The ignition switch is a three-position, key-operated switch. Use the ignition switch to start the engine.
See page 54 for starting procedures.The key can be removed from the switch when it is in the OFF position.
OFF
The engine is off. Electrical circuits are off, except accessory as winch motor.
NO
Electrical circuits are on. Electrical equipment can be used.
START
Turn the key to the START position to engage the electric starter.The key returns to
the ON position when released.
Light Switch
”
”、“
Light switch including:“
、“
”
light switch on this position,headlight,instrument light,front and rear sidelights lighted.
light switch on this position,instrument light,front and rear sidelights lighted.
light switch on this position,headlight,instrument light,front and rear sidelights closed. High and lower beam
light switchs
turn on high beam light.
High and lower beam light switch on this position and light switch as
High and lower beam light switch on this position and light switch as
turn on lower beam ligh.
Note:The ignition switch must be in the ON position to operate
-39-
turn switch
Press switch to
Press switch to
,turn on the turn light(left) and indicator light.
,turn on the turn light(right) and indicator light.
Horn switch
Press the switch, horn working.
Aeta switch
Speed is limited base on AWD.if need to more power when drive to overtake, release the speed limited if press
the aeta switch(See page 41.detail instruction for AWD switch and founctions). Reserve the speed
limited function if loosen the aeta switch. Aeta indicator light is lighten when press the switch.
Flameout switch
press
button,engine stopped,press
button,engine operated.
Auxiliary Outlet
Auxiliary outlet voltage:12V;Max outlet current:10A.
-40-
Switchs
4WD switch
2WD to 4WD,stop the vehicle,change the switch to
“ 4WD ” 。
When the switch on 4WD , 4WD indicator lightwill be on
.
4WD to 2WD,stop the vehicle,confirm the rocker ① on the
a ,press the switch to“2WD ”.
Position ○
4WD and 4WD - Lock switch
“LOCK”/“4WD”
①
Lock front wheel drive on 4WD ,confrim 4WD switch on the
b ,then if swith on
“4WD”,stop vehicle, press the rocker ②to ○
the position as“LOCK ” . when locked the 4WD, 4WD-Lock
indicator light will be on . open 4WD-Lock switch,stop the
vehicle,change the switch to“ 4WD”
Note
● when the switch on “ LOCK ” , indicator light is twinkle unitil locked 4WD.
● when the 4WD -Lock indicatior light twinkl e, turn left or right for steering wheel, it is better to front wheel for 4WD
Locked.
● confirm whether it is 4WD -Lock(For example,indicator light is twinkle )and speed limited of Engine unitl it is over.
● when vehicle as 4WD -LOCK .speed limited under 35 km/h (22 mph).if need to full power of engine.Don’ t release the
aeta switch can release the speed limited of 4WD -LOCK .
-41-
Park
P:Park, when vehicle stopped, fllow the arrow direction to operate the park handle for parking
Parking indicator light will be on, if need to be released it that press the release button as the arrow direction.
Gear selector
Gears
L:Low Gear
H:High Gear
N:Neutral
R:Reverse
To change gears, stop the vehicle,and with the engine idling,
move the lever to the desired gear. Do not attempt to shift gears with engine
speed above idle or while the vehicle is moving.
gear shaft
Lock button
NOTE:
Maintaining shift linkage adjustment is important to assure proper transmission function. See your dealer if
you experience any shifting problems.
CAUTION
Do not attempt to shift the transmission while the vehicle is moving or damage to the transmission could result.
Always shift when the vehicle isstationary and the engine is at idle.
Using Low Range and High Range
Condition
Range to Use
Operating at speeds less than 7 PH (11 km/h)
LOW
Operating in rough terrain or over obstacles
LOW
Loading the vehicle onto a trailer
Towing heavy loads
Operating at speeds greater than 7 MPH (11 km/h)
LOW
LOW
High
-42-
Brake Pedal
Depress the brake pedal to slow or stop the vehicle.
Apply the brakes while starting the engine.if feel softly of brake pedal before driving,
inspect the brake fluid whether it is between the superior and lower limited or oil leak of
oil tube,even exhaust the air of channel.
Throttle Pedal
Push the pedal down to increase engine speed.
Spring pressure returns the pedal to the rest position
when released. Always check that the throttle pedal
returns normally before starting the engine. Make sure
there's adequate throttle pedal freeplay. See page 98
for throttle pedal adjustment procedures.
Throttle Pedal
Brake Pedal
-43-
Instrument Cluster
Cooling liquid temperature indicator①
Temperature indicator pointer on the white zond C.Temperature
Is normal.Temperature indicator pointer on the red zone H.
Engine stop and cooling liquid temperature drop down.if
Temperature is frequently overtop,inspect the volumn of
Cooling liquid and inquire the localled dealer.
caution
●if ATV is overweight,engine will be superheating.if like this,
Reduce the load weight in the scope of mas load weight.
●Restart engine. Confirm the temperature pointer in the white
Zone C. when the pointer in the red zone, engine will be
damaged 。
Speedmeter②: display speed.
odometer③: display odo
Fuel gauge④ : display the surplus fuel. “F” fuel total:27L.when pointer in the red zone, show that the
surplus fuel only 4.01,need to refuel.
-44-
4WD indicator light①
switch “2WD”/“4WD” on the position“4WD”. 4WD indicator light will be on.
switch“LOCK”-“4WD”on the position“LOCK -4WD ”,4WD-Lock indicatior light will be on.
4WD indicatior light will be on after vehicle moving due to the mechanical synchronous sets in the front
wheel driving case.
Turn left indicator light②
Switch on the position“”indicator light will be on.
Low gears indicatior light“L”③
Gears on the position“L”,indicator light will be on.
High gears indicator light “H”④
Gears on the position “H” indicator light will be on.
Neutralindicator light“N”⑤
Gears on the position “N” indicator light will be on.
Reverse indicator light “R”⑥
Gears on the position “R” indicator light will be on.
-45-
Instrument Cluster
Parking indicator light “P”⑦
Switch on the position“P”,indicatior light will be on.
Turn right indicator light ⑧
Switch on the position“”,indicator light will be on.
Aeta indicator light ⑨
Press aeta switch,indicator light will be on.
High beam indicator ligth⑩
and light switch on the position
Switch on the position
Sidelights indicator light⑾
Light switch on the position
Indicatior light will be on.
,indicator light will be on.
Malfunction Indicator Lamp ⑿
When vehicle is malfunction,the malfunction indicator lamp will be on.(see page 47).
Clock ⒀
Display time, clock adjustment (see page 39)
Note:
Indicator light is lighten and speedmeter is'not working,inquire the local dealer and insepct the speed sensor
whether it is defect.
-46-
Instrument Cluster
Error code
Error code as four digit blink model:
For example:0650
“0”:blink 10 times;
“6”:blink 6 times;
“5”:blink 5 times;
“0”:blink 10 times;
Refe no Error code Failure Description
14
P0030
P0031
P0032
P0053
P0105
P0106
P0107
P0108
P0112
P0113
15
16
17
1
2
3
7
9
10
11
12
13
-47-
O2 Sensor Heater Contr. Circ/Open
O2 Sensor Heater Contr. Circ. Low
Defects type
Signal defects
Min defects
O2 Sensor Heater Contr. Circ. High
Max defects
O2 Sensor Heater Resistance
Manifold Abs . Pressure or Bar.Pressure Circuit
Manifold Abs.Pressure or Bar.Pressure Range/Performance
Manifold Abs.Pressure or Bar.Pressure Low Input
Manifold Abs.Pressure or Bar.Pressure High Input
Intake Air Temp.Circ. Low Input
Min defects
Max defects
Max defects
Mi n defects
P0116
Intake Air Temp.Circ. High Input
Engine Coolant Temp.Circ. Range/Performance
P0117
Engine Coolant Temp.Circ. Low Input
Max defects
P0118
Engine Coolant Temp.Circ. High Input
Min defects
Instrument Cluster
Error code
Error code as four digit blink model:
For example:0650
“0”:blink 10 times;
“6”:blink 6 times;
“5”:blink 5 times;
“0”:blink 10 times;
Refe no Error code
18
P0122
19
P0123
20
P0130
21
P0131
22
P0132
23
P0133
24
P0134
29
P0170
30
P0171
31
P0172
Failure Description
Throttle Pos.Sensor Circ. Low Input
Throttle Pos.Sensor Circ. High Input
Defects type
Min. error
Max. error
O2 Sensor Circ. Malfunction
O2 Sensor Circ. Low Voltage
O2 Sensor Circ. High Voltage
O2 Sensor Circ. Slow Response
O2 Sensor Circ. No Activity Detected
Fuel Trim, Malfunction
Fuel Trim, System too Lean
Fuel Trim, System too Rich
Signal error
P0202
Cylinder 1- Injector Circuit
Cylinder 2- Injector Circuit
P0261
Cylinder 1- Injector Circuit Low
Min. error
32
P0201
33
36
Only for 2-cylinder
engine
-48-
Instrument Cluster
Error code
Downloading Codes by Following:
E.G. :0650
“0”:blink 10 times;
“6”:blink 6 times;
“5”:blink 5 times;
“0”:blink 10 times;
REF
Error code
37
38
P0262
P0264
Cylinder 2- Injector Circuit Low
39
P0265
51
P0321
P0322
P0444
P0458
P0459
P0501
P0506
P0507
P0508
P0509
Cylinder 2- Injector Circuit High
Engine Speed Reference Mark
Eng.Speed Inp.Circ. No Signal
52
60
61
62
65
66
67
68
69
-49-
Failure Description
Cylinder 1- Injector Circuit High
Evaporative Emiss.System Purge Control Valve Circ. Open
Sort
Serious problem
Signal problem
Evaporative Emission System Purge Control Valve Circuit Low
Evaporative Emission System Purge Control Valve Circuit High
Vehicle Speed Sensor Range/Performance
Idle Control System RPM Lower than Expected
Idle Control System RPM Higher than Expected
Drive pi n of st ep mot or : sho rt ci rcui t to gr ound
Drive pi n of st ep mot or : shor t ci rcui t to bat ter y
Signal problem
Instrument Cluster
Error code
Downloading Codes by Following:
E.G. :0650
“0”:blink 10 times;
“6”:blink 6 times;
“5”:blink 5 times;
“0”:blink 10 times;
REF
Error code
70
75
P0511
76
77
78
79
80
81
85
91
92
93
94
P0563
P0602
P0627
P0628
P0629
P0650
P2177
P2178
P2195
P2196
Failure Description
Sort
P0560
Drive pin of step motor: open circuit
System Voltage Malfunction
Unreasonable problem
P0562
System Voltage Low Voltage
Unimportant problem
System Voltage High Voltage
Serious problem
Control Module Programming Error
Fuel Pump Control Circuit /Open
Fuel Pump Control Circuit Low
Fuel Pump Control Circuit High
Drive circuit error of MIL light
System Too Lean
System Too Rich
O2 Sensor Circ., Slow Response lean
O2 Sensor Circ., Slow Response rich
Signal problem
Unimportant problem
Unimportant problem
-50-
OPERATION
Vehicle Break-In Period
The break-in period for your new CFMOTO vehicle is the first 20 hours of operation, or the time it takes to use
the first two tanks full of gasoline.No single action on your part is as important as a proper break-in period.
Careful treatment of a new engine and drive components will result in more efficient performance and longer
life for these components. Perform the following procedures carefully.
CAUTION
Excessive heat build-up during the first three hours of operation will damage close-fitted engine parts and
drive components. Do not operate at full throttle or more 50KM/H during the first three hours of using.
Use of any oils other than those recommended by us may cause serious engine damage. We recommend
the use of SAE 15/W40 SG oil.
-51-
OPERATION
Vehicle Break-In Period
The break-in period for your vehicle is defined on the previous page.
Please read the information carefully.
Engine and Drivetrain Break-in
1. Fill the fuel tank with gasoline. See page 36.
2. Check the oil level. See page 81. Add the recommended oil as needed to maintain the oil level in
the safe operating range.
3.Complete the New Operator Driving Procedures outlined on pages 57-58
NOTE: Avoid aggressive use of the brakes. See Brake System Break-in.
4. Vary throttle positions. Do not operate at sustained idle.
5.Perform regular checks on fluid levels, controls and areas outlined on the daily pre-ride inspection
checklist. See page 53.
6.Pull only light loads.
7.During the break-in period, change both the oil and the filter at 20 hours or 250km
Brake System Break-in
Apply only moderate braking force for the first 50 stops. Aggressive or overly forceful braking when
the brake system is new could damage brake pads and rotors.
CVT Break-in (Clutches/Belt)
A proper break-in of the clutches and drive belt will ensure a longer life and better performance. Break
in the clutches and belt by operating at slower speeds during the break-in period as recommended.
Pull only light loads. Avoid aggressive acceleration and high speed operation during the break-in period.
-52-
Pre-Ride Inspection
If a proper inspection is not done before each use, severe injury or death could result. Always inspect the
vehicle before each use to ensure it's in proper operating condition.
Item
Brake system/pedal travel
Brake fluid
Front suspension
Rear suspension
Steering
Tires
Wheels/fasteners
Frame nuts, bolts, fasteners
Fuel and oil
Coolant level
Coolant hoses
Throttle
Indicator lights/switches
Air filter, pre-filter
Headlamp
Brake light/tail lamp
Seat Latches
Seat Belts
Cab Nets
-53-
Remarks
Ensure proper operation
Ensure proper level
Inspect, lubricate if necessary
Inspect, lubricate if necessary
Ensure free operation
Inspect condition and pressure
Inspect, ensure fastener tightness
Inspect, ensure tightness
Ensure proper levels
Ensure proper level
Inspect for leaks
Ensure proper operation
Ensure proper operation
Inspect, clean
Check operation, apply CFMOTO dielectric grease when lamp is replaced
Check operation, apply CFMOTO dielectric grease when lamp is replaced
Push down on both seat backs to ensure the latches are secure
Check length of belt for damage, check latches for proper operation
Check for wear or damage, ensure proper installation
Page
43,99
100
78
78
101
4,103
103
44,81
91,92
97
39
95
105
107
34
37
Starting the Engine
Engine exhaust contains poisonous carbon monoxide and can cause loss of consciousness resulting in
severe injury or death. Never run an engine in an enclosed area.
1.Sit in the driver's seat and fasten the seat belt.
2.Place the transmission in PARK.
3.Apply the brakes.
NOTE: Do not press the throttle pedal while starting the engine.
4.Turn the ignition key past the ON/RUN position to START. Engage the starter for a maximum of five
seconds. Release the key when the engine starts.
5.If the engine does not start within five seconds, return the ignition switch to the OFF position and
wait five seconds. Repeat steps 4 and 5 until the engine starts.
6.Vary the engine RPM slightly with the throttle to aid in warm up until the engine idles smoothly.
Stopping the Engine
Operating the vehicle immediately after starting could cause engine damage. Allow the engine to warm up for
several minutes before operating the vehicle.
1.Release the throttle pedal completely and brake to a complete stop.
2.Place the transmission in PARK.
3.Turn the engine off.
A rolling vehicle can cause property damage and serious injury. Always place the transmission in PARK
when stopping the engine.
-54-
Braking
1.Release the throttle pedal completely.
2.Press on the brake pedal evenly and firmly. Practice starting and stopping (using the brakes) until you're
familiar with the controls.
NOTE: When the throttle pedal is released completely and engine speed slows to near idle, the vehicle has
no engine braking.
Failure to allow for increased braking distance when hauling cargo or towing a trailer may result in accident
and injury. Always slow down and allow additional braking distance when towing or hauling cargo.
-55-
Parking the Vehicle
Gasoline is extremely flammable and can be explosive under certain conditions. When parking inside a garage
or other structure, be sure that the structure is well ventilated and that the vehicle is not close to any source
of flame or sparks, including any appliance with pilot lights.
A rolling vehicle can cause property damage and serious injury. Always place the transmission in PARK when
stopping the engine.
1. Stop the vehicle on a level surface. Place the transmission in PARK.
2. Turn the engine off.
3. Remove the ignition switch key to prevent unauthorized use.
-56-
New Operator Driving Procedures
Operating improperly can cause an accident or overturn which could result in severe injury or death. This
vehicle handles differently than cars, trucks or other off-road vehicles. Operators of this vehicle must become
familiar with vehicle handling at slow speeds before operating at faster speeds.
Do not carry a passenger until you have at least two hours of driving experience with this vehicle.
1. Do not carry a passenger until you have at least two hours of driving experience with this vehicle.
2. Do not tow or carry cargo during this period.
3. Select an open area that allows room to familiarize yourself with vehicle operation and handling. Check
your surroundings and determine your path of travel.
4. Keeping both hands on the steering wheel, slowly release the brakes and depress the throttle with your
right foot to begin driving.
-57-
New Operator Driving Procedures
5.Drive slowly at first. On level surfaces, practice starting, stopping, turning, maneuvering, using the throttle and brakes and driving in reverse. Learn how the vehicle handles
when making both left and right turns at a slow speed.
6.Increase speed only after mastering all maneuvers at a slow speed.
7.After you become skilled at making turns and begin to operate at faster speeds, follow
these precautions:
●Avoid sharp turns.
●Never turn while applying heavy throttle.
●Never make abrupt steering maneuvers.
●Operate at speeds appropriate for your skills, the conditions and the terrain.
●DO NOT do power slides, “donuts”, jumps or other driving stunts.
-58-
Driving with a Passenger
1.Complete the New Operator Driving Procedures outlined on pages 57-58.
2.Perform the pre-ride inspection. See page53.
3.Make sure the passenger is at least 12 years of age and is tall enough to comfortably and safely sit in the
passenger seat with the seat belt secured, put both feet on the floor and grasp the hand holds.
4.Make sure the passenger is wearing appropriate riding gear, including an approved helmet and eye
protection. See page 13.
5.Make sure the passenger secures the seat belt.
-59-
Driving with a Passenger
6.Allow a passenger to ride only in the passenger seat.
7.Do not carry more than one passenger. Additional passengers can affect the operator's ability to steer
and operate the controls.
8.Slow down. Always travel at a speed appropriate for your skills, your passenger's skills, and operating
conditions. Avoid unexpected or aggressive maneuvers that could cause discomfort or injury to a passenger.
9.Vehicle handling may change with a passenger and/or cargo on board. Allow more time and distance for
braking.
10.Always follow all operating guidelines as outlined on safety labels and in this manual
-60-
Driving on Slippery Surfaces
When driving on slipperysurfaces such as wet trails,、
loose gravel, or ice, be alert for the possibility of skidding
and sliding. Under these conditions, follow these precautions:
1.Slow down when entering slippery areas.
2.Maintain a high level of alertness, reading the trail
and avoiding quick, sharp turns, which can cause skids.
3.Engage all-wheel drive before wheels begin to lose traction.
4.Correct a skid by turning the steering wheel in the direction of the
skid.
Severe damage to the drive train may occur if the AWD is engaged while the wheels are spinning. Always allow
the wheels to stop spinning before engaging AWD.
Failure to exercise care when operating on slippery surfaces can result in loss of tire traction and cause loss
of control, accident, and serious injury or death.
Never apply the brakes during a skid.
Do not operate on excessively slippery surfaces.
Always reduce speed and use additional caution when operating on slippery surfaces.
-61-
Driving Uphill
Whenever traveling uphill, follow these precautions:
1. Drive straight uphill.
2. Proceed at a steady rate of speed and throttle opening.
Avoid unnecessary changes in speed or direction.
3. Avoid steep hills (15° maximum).
NOTE: If ascending a steeper grade is unavoidable,
engage all-wheel drive before ascending.
4. If the vehicle stalls while climbing a hill,
apply the brakes. Place the transmission in reverse
and slowly allow the vehicle to roll straight downhill
while applying light brake pressure to control speed.
Climbing hills improperly can cause loss of control or vehicle overturn. Always check the terrain carefully
before climbing a hill.
Braking and handling are greatly affected when operating in hilly terrain.Improper operating procedures could
cause loss of control or overturn and result in serious injury or death.
Avoid climbing steep hills (15° maximum).
Use extreme caution when operating on hills, and follow proper operating procedures outlined in the owner's
manual.
Never climb hills with excessively slippery or loose surfaces.
Never open the throttle suddenly.
Never go over the crest of a hill at high speed. An obstacle, a sharp drop, or another vehicle or person could
be on the other side of the hill.
-62-
Driving on a Sidehill (Sidehilling)
Avoid driving across the side of a hill. Control becomes difficult and there is an increased chance of vehicle
overturn when driving on a hillside.
If crossing a hill is unavoidable, follow these precautions:
1.Engage all-wheel drive.
2.Drive slowly and use extreme caution.
3.If the vehicle begins to overturn, or if it feels as if it may overturn, immediately turn downhill.
4.Avoid obstacles and changes in terrain that may lower or raise one side of the vehicle or cause the
vehicle to slide.
5.If the vehicle begins to slide downhill, immediately turn downhill to stop the slide, or stop the vehicle and
maneuver slowly and carefully until the vehicle can be driven straight downhill.
Crossing hillsides or turning on hills can result in loss of control or vehicle overturn, resulting in severe injury
or death. Avoid crossing the side of a hill. Avoid operating on steep hills (15° maximum).
-63-
Driving Downhill
Whenever descending a hill, follow these precautions:
1.Slow down.
2.Always descend a hill with the transmission in forward gear. Never descend a hill with the transmission
in neutral.
3.Travel straight downhill.
4.Apply the brakes lightly to aid in slowing.
Traveling downhill improperly could cause loss of control or vehicle overturn.
Always check the terrain carefully before descending a hill.
Never descend a hill at high speed. Excessive speed may result in loss of vehicle control and lead to serious
injury or death. Always operate slowly when traveling downhill.
Avoid descending a hill at an angle, which would cause the vehicle to lean sharply to one side. Travel straight
downhill.。
-64-
DRIVING
Driving in water
The large tires on your vehicle may cause the vehicle to float in deep or fastflowing
water, which could result in loss of control and lead to serious injury
or death. Never cross deep or fast-flowing water with your vehicle.
Your vehicle can operate through waer with a maximum recommended depth eual to floor level. Follow
these Procedures when operating through water:
1.Determine water depth and current before crossing;
2.Never operate in water that exceeds the maximum
Recommended depth;
3.Choose a crossing where both banks have gradual inclines;。
4.Proceed slowly, avoiding rocks and obstacles;
5.Wet brakes may have reduced stopping ability;
6. To dry out the pads,apply the brakes lightly several times
while driving slowly.
Notes:After running your vehicle in water, it's critical that you
perform the services outlined in the Periodic Maintenance Chart
beginning on page 72. Give special attention to engine oil,
transmission oil,demand drive fluid, rear gearcase oil, and all grease fittings.
Level of footrest board
CAUTION
Immersion can result in major damage if the vehicle isn't serviced correctly and promptly. After immersion,
always take the vehicle to your dealer for service. Do not start the engine. If it's impossible to bring the
vehicle to your dealer before starting the engine, perform the service outlined on page 112, and take the vehicle to
dealershop .
-65-
OPERATION
DRIVE OVER OBSTACLES
1.Be alert! Look ahead and learn to read the terrain you're travelingon. Watch for hazards such as logs, rocks
and low hanging branches
2.Before operating in a new area, check for obstacles.
3.Avoid operating over large obstacles such as rocks and fallen trees.If unavoidable, use extreme caution
and operate slowly.
4.Always have a passenger dismount and move away from the vehicle before operating over an obstacle that
could cause an overturn.
Severe injury or death can result if your vehicle suddenly comes in contact with a hidden obstacle. Not all
obstacles are immediately visible. Reduce speed and travel with caution in unfamiliar terrain.
-66-
OPERATION
Driving in Reverse
Follow these guidelines when operating in reverse:
1.Always check for obstacles or people behind the vehicle;
2.Apply the throttle lightly. Never open the throttle suddenly;
3.Back slowly;
4.Apply the brakes lightly for stopping;
5.Avoid making sharp turns
Failure to use caution when operating in reverse can result in serious injury or death. Before shifting into
reverse, always check for obstacles or people behind the vehicle. When it's safe to proceed, back slowly.
Avoid making sharp turns.
-67-
Parking on an Incline
Avoid parking on an incline if possible. If it's unavoidable, follow these precautions:
1.Place the transmission in PARK;
2.Turn off the engine;
3.Block the rear wheels on the downhill side;
A rolling vehicle can cause property damage and serious injury. Always place the transmission in PARK when
stopping the engine. Always block the downhill side of the wheels if leaving the vehicle on a hill, or park the
vehicle in a sidehill position instead.
-68-
Hauling Cargo
Overloading the vehicle or carrying or towing cargo improperly can altervehicle handling and may cause loss
of control or brake instability. Always follow these precautions when hauling cargo:
Never exceed the stated load capacity for this vehicle.
REDUCE SPEED AND ALLOW GREATER DISTANCES FOR BRAKING WHEN HAULING CARGO.
When operating over rough or hilly terrain, reduce speed and cargo to maintain stable driving conditions.
Always operate the vehicle with extreme care when hauling or towing loads. Slow down and drive in the lowest
gear available.
OPERATE ONLY WITH STABLE AND SAFELY ARRANGED LOADS. When handling off-centered loads
that cannot be centered, securely fasten the load and operate with extra caution. Always attach the
tow load to the hitch point designated for your vehicle.
HEAVY LOADS CAN CAUSE BRAKING AND CONTROL PROBLEMS. Use extreme caution when applying
brakes with a loaded vehicle. Avoid terrain or situations that may require backing downhill.
USE EXTREME CAUTION when operating with loads that extend over the rack sides. Stability and maneuverability may be adversely affected, causing the vehicle to overturn
DO NOT TRAVEL FASTER THAN THE RECOMMENDED SPEEDS. Vehicle should never exceed 10 mph (16
kph) while towing a load on a level grass surface. Vehicle speed should never exceed 5 mph (8 kph)
when towing loads in rough terrain, while cornering, or while ascending or descending a hill.
Driving with passengers in the cargo box can result in
severre injury or death.
Never allow a passenger to ride in the
cargo box. A passenger must always
ride in the passenger seat with the seat
belt fastened securely.
-69-
Hauling cargo
Your CFMOTO vehicle has been designed to carry or tow specific capacities. Reduce speed and allow a greater
distance for braking when carrying cargo.
Loads should be centered and carried as low as possible in the box. For stability on rough or hilly terrain,
reduce both speed and cargo. Exercise caution if the cargo load extends over the side of the box.
Always read and understand the load distribution warnings listed on warning labels and in this manual. Never
exceed the maximum capacities specified for your vehicle. See page 120.
Belt life
To extend belt life, use low gear when hauling or towing heavy cargo.
Towing loads
Towing improperly can alter vehicle handling and may cause loss of control or brake instability, which can
result in serious injury or death. Always follow these precautions when towing:
Never load more than 110 lbs. (55 kg) tongue weight on the towing bracket.
Do not operate the vehicle too fast when towing. Towing a trailer increases braking distance.
Do not tow more than the recommended weight for the vehicle.
Attach a trailer to the trailer hitch bracket only. Do not attach a trailer to any other location, which could result
in loss of control of the vehicle.
TOTAL
MODEL
LOAD
TOWED
WEIGHT
(LEVEL GROUND)
TOTAL
HITCH
VERTICAL
WEIGHT
CF625-3
275.3lbs(125kg)
110ibs(50kg)
CF500-6
275.3lbs(125kg)
110ibs(50kg)
-70-
EMISSION CONTROL SYSTEMS
Noise Emission Control System
Do not modify the engine, intake or exhaust components, as doing so may affect compliance with U.S.A. EPA
noise control requirements (40 CFR 205) and local noise level requirements.
Operation on Public Lands in the U.S.A.
Your vehicle has a spark arrestor that was tested and qualified to be in accordance with the USDA Forest Service Standard 5100-1C.
Federal law requires that this spark arrestor be installed and functional when the vehicle is operated on public
lands.
Operation of off-road vehicles on public lands in the U.S.A. is regulated by 43 CFR 8343. Violations are
subject to monetary penalties. Federal regulations can be viewed online at www.gpoaccess.gov/ecfr/.
Crankcase Emission Control System
This engine is equipped with a closed crankcase system. Blow-by gases are forced back to the combustion
chamber by the intake system. All exhaust gases exit through the exhaust system.
Exhaust Emission Control System
Exhaust emissions are controlled by engine design. An electronic fuel injection (EFI) system controls fuel
delivery. The engine and EFI components are set at the factory for optimal performance and are not
adjustable. The emissions label is located on the lower frame behind the driver's seat
.
Electromagnetic Interference
This spark ignition system complies with Canadian ICES-002. This vehicle complies with European directives
97/24/EC and 89/336/ EEC.
-71-
MAINTENANCE
Periodic Maintenance Chart
.
Careful periodic maintenance will help keep your vehicle in the safest, most reliable condition. Inspection,
adjustment and lubrication of important components are explained in the periodic maintenance chart. Inspect,
clean, lubricate, adjust and replace parts as necessary. When inspection reveals the need for replacement
parts, use genuine parts available from your dealer
NOTE:Service and adjustments are important for proper vehicle operation. If you're not familiar with safe
service and adjustment procedures, have a qualified dealer perform these operations.
Maintenance intervals in the following chart are based upon average riding conditions and an average vehicle
s peed of approximately 30 kilometers per hour. Vehicles subjected to severe use must be inspected
and serviced more frequently.
Severe Use Definition
●Frequent immersion in mud, water or sand
●Racing or race-style high RPM use
●Prolonged low speed, heavy load operation
●Extended idle
●Short trip cold weather operation
Pay special attention to the oil level. A rise in oil level during cold weather can indicate contaminants collecting
in the oil sump or crankcase. Change oil immediately if the oil level begins to rise. Monitor the oil level, and if
it continues to rise, discontinue use and determine the cause or see your dealer.
-72-
Periodic Maintenance Chart
Maintenance Chart Key
▲Perform these operations more often for vehicles subjected to severe use.
E Emission-related service (Failure to conduct this maintenance will not void the emissions warranty but may
affect emissions.)
■Have an authorized dealer perform these services.
Improperly performing the procedures marked with a ■ could result in component failure and lead to
serious injury or death. Have an authorized dealer perform these services.
-73-
Periodic Maintenance Chart
Perform all services at whichever maintenance interval is reached first.
ITEMS
Maintenance Interval
REMARKS
(whichever comes first)
HOURS
CALENDAR MILES(km)
■
▲
Steering
Front suspension
——
——
Pre-Ride
Pre-Ride
——
——
▲
Rear suspension
——
Pre-Ride
——
▲
Tires
Brake fluid level
——
——
Pre-Ride
Pre-Ride
——
——
▲
Brake padal level
Brake system
——
Pre-Ride
——
Wheels /fasteners
Frame fasteners
——
——
Pre-Ride
Pre-Ride
——
——
Engine oil level
——
Pre-Ride
——
Air filter
——
Daily
——
Check, clean frequently, replace if
necessary.
Coolant
——
Daily
——
Inspect level on daily basis, change
everytwo years.
Headlamp /Tail
light
——
Daily
——
Check operation; apply dielectric
grease if replacing
▲
▲
E
Make adjustments as needed. See
Pre-Ride Checklist on page 51
▲Perform these procedures more often for vehicles subjected to severe use.
E Emission-Related Service
■ Have an authorized CFMOTO dealer perform these services.
-74-
Maintanence
Periodic Maintenance Chart
Item
Maintanence
Interval
comes )
first
Calendar Miles(km)
Remarks
(whichever
Hours
▲
Air filter, main element 50
——
300(500)
Brake pad wear
10H
Monthly
100(160)
▲
Inspect periodically
Inspect; clean every 100H or 1000km;
change every 20000km.
E
■
Battery
25H
Monthly
250(400)
Check terminals; clean; test
▲
Main gearcase oil
25H
Monthly
250(400)
Inspect level; change yearly
▲
Rear gearcase oil
25H
Monthly
250(400)
Inspect level; change yearly
▲
Engine breather filter
25H
Monthly
150(250)
Inspect, replace if necessary
Engine
oil
20H
——
150(250)
Replace with oil filter change
■
Throttle cable/ switch,
50H
6M
300(500)
Inspect;
E
etc.
■
Valve clearance
100H
——
600(1000)
Inspect and adjust at the first 20H or 250km
Throttle body air
50H
6M
300(500)
Inspect duct for proper sealing/air leaks
100H
——
600(1000)
Inspect; change every four years
E
▲
change(break-in)
adjust;
lubricate;
replace if
necessary
E
E
intake ducts/flange
E
High-pressure
oil
Perform these procedures more often for vehicles subjected to severe use.
E Emission-Related Service.
■ Have an authorized CFMOTO dealer perform these services.
▲
-75-
Periodic Maintenance Chart
Item
Maintanence Interval
Remarks
(whichever comes first
)
Hours
▲
Calendar Miles(km)
General lubrication 50H
3M
500(800)
Shift linkage
50H
6M
500(800)
Lubricate all fittings, pivots, cables,
etc.
Inspect, lubricate, sdjust
■
Steering
50H
6M
500(800)
lubricate
▲
▲
Front suspension
Rear suspension
50H
50H
6M
6M
500(800)
500(800)
lubricate
lubricate
Cooling system
50H
6M
500(800)
Inspect coolant strength seasonally;
test system presasure yearly
■
E
Fuel system
100H
12M
600(1000)
Check for leak at tank cap, lines, filter,
pump; replace lines every two years
▲
E
▲
Spark plug
100H
——
600(1000)
Inspect at first 250km or 20H. replace
every 6000km.
100H
100H
——
▲
Engine oil change
Oil filter
——
600(1000)
600(1000)
Perform a break-in oil change at 20H
Replace with oil change
▲
Radiator
100H
12M
1000(1600)
Inspect, clean external surface
▲ Perform these procedures more often for vehicles subjected to severe use.
E Emission- Related Service.
■ Have an authorized CFMOTO dealer perform these services.
-76-
Periodic Maintenance Chart
Periodic Maintenance Chart
Item
Maintanence Interval
Remarks
(whichever comes first
)
Hours
▲
▲
Calendar
Miles(km)
Cooling hoses
Engine mounts
100H
100H
——
12M
600(1000)
1000(1600)
Inspect for leaks at the first 20H or 250km
Inspect
Exhaust
muffler/pipe
100H
12M
1000(1600)
Inspect
■
▲
Ignition timing
Wiring
100H
100H
12M
12M
1000(1600)
1000(1600)
Inspect
Inspect for wear,routing, security; apply
dielectric grease to connector subjected
to water, mud, etc.
■
Clutch
Drive belt
100H
600(1000)
300(500)
Inspect; clean; replace worn parts
Inspect,replace every 2000km
50H
100H
12M
1000(1600)
Inspect,replace as needed
■
Front
bearings
■
Brake fluid
Spark arrestor
200H
300H
24M
36M
2000(3200)
3000(4800)
Replace every two years
Clean out
■
■
Idle speed
——
——
——
——
——
——
Adjust as needed
Toe adjustment
Headlight aim
——
——
——
Adjust as needed
wheel
Inspect periodically, adjust when parts
are replaced
Perform these procedures more often for vehicles subjected to severe use.
E Emission-Related Service.
■Have an authorized CFMOTO dealer perform the services.
▲
-77-
Lubrication Recommendations
Check and lubricate all components at the intervals outlined in the Periodic Maintenance Chart beginning on
Page 73, or more often under severe use, such as wet or dusty conditions. Items not listed in the chart should
be lubricated at the general lubrication intervals.
Item
Lube
Method
Engine Oil
SAE15W/40 SG
Brake Fluid
DOT3 or DOT4
Add to proper level on dipstick, See
page 82
Maintain level between fill lines,See
page 92
Transmission Oil(main
gearcase)
Transmission Oil(rear
gearcase)
SAE15W/40 SG or SAE80W/90
Prop Shaft
Control Arm Pivot Bushings,
Front/Rear
U-joint lube
NLGI No.2
Locate fittings and grease
Locate fittings and grease
Stabilizer Bar Bushings,
Front/Rear
NLGI No.2
Locate fittings and grease
See page 85
GL-4
SAE15W/40 SG or SAE80W/90
See page 86
GL-4
-78-
Lubrication Recommendations:
Control Arm Pivot
Bushings, Front/Rear
-79-
Engine Oil
Always check and change engine oil at intervals outlined in the Periodic Maintenance Chart beginning on
page 72. Always change the oil filter whenever changing oil.
SAE15W/40 SG Oil
We strongly recommend use of SAE15W/40 SG Oil,
API certified “S G”oil. If SAE15W/40 SG Oil is
unavailable,choose oil following the right instructions
according to the engine ambient temperature.
Oil may need to be changed more frequently if SAE15W/40 SG oil is not used. Follow the manufacture's
instructions for
ambient temperature operation.
CAUTION
Mixing brands or using a non-recommended oil may cause serious damage to the engine. We recommend use
of SAE15W/40 SG Oil, never use substitute or mix oil brands.
Vehicle operation with insufficient, deteriorated, or contaminated engine oil will cause accelerated wear and
may result in engine seizure, accident and injury. Always perform the maintenance procedure as outlined in
the Periodic Maintenance Chart.
-80-
Engine Oil
Always check and change engine oil at intervals outlined in the Periodic Maintenance Chart beginning on page
72. Always change the oil filter whenever changing oil.
Oil Check
Dipstick
The oil dipstick and fill tube is located on the engine, behind the
passenger seat.
1. Position the vehicle on a level surface.
2. Place the transmission in PARK.Apply the brakes.
3. Start the engine.Allow it to idle for 20-30 seconds.
Stop the engine.
4.Remove both seats.Remove the rear service panel.
See page 34.
5.Remove the dipstick from the left side.
Wipe it dry with a clean cloth.
6.Reinstall the dipstick completely, but do not lock it.
The dipstick must be inserted completely to keep the angle and
depth of the stick consistent.
7.Remove the dipstick and check the level. Maintain the oil level within the upper and lower limit.
Do not overfill.
Oil dipstick
NOTE:Due to the dipstick entry angle into the crankcase,
the oil level will read higher on the bottom side of the dipstick.
Always read the level on the upper surface of the dipstick.
8.Reinstall the dipstick. Seat the lever lock.
Upper limit
Lower limit
-81-
Engine Oil
Oil and Filter Change
CAUTION
Hot oil can cause serious burns to skin. Do not allow hot oil to come into contact with skin.
Always check and change engine oil at intervals outlined in the Periodic Maintenance Chart beginning on
page 72. Always change the oil filter whenever changing oil.
The engine drain plug is located on the bottom of the crankcase.
1. Position the vehicle on a level surface.
Place the transmission in PARK.Apply the brakes
2. Start the engine.Allow it to idle for 2-3minutes.
Stop the engine.
3. Clean the area around the drain plug.
4. Place a drain pan beneath engine crankcase and remove
the drain plug.
5. Allow the oil to drain completely.
6. Reinstall the sealing washer on the drain plug.
NOTE:The sealing surface on drain plug and crankcase
should be clean and free of burrs,nicks or scratches.
7.Drain plug,torque:22ft.lbs(30Nm)
Engine oil Drain plug
-82-
Engine Oil
Oil and Filter Change
8.Using a cap-style oil filter wrench, turn the filter counter-clockwise to remove it.
9.Using a clean dry cloth, clean the filter sealing surface on the crankcase.
10.Lubricate the o-ring on the new filter with a film of fresh engine oil.Check to make sure the o-ring is in good
condition.
11.Install the new filter and turn by hand until the filter gascket contacts the sealing surface,then turn an
additional 1/2 turn with special wrench.
12.Remove the dipstick and fill with 2.5L recommended oil.
13.Place the transmission in PARK.Apply the brakes
14. Start the engine.Allow it to idle for 2 minutes.
15.Stop the engine. Inspect for leaks.
16.Re-check the oil level on the dipstick and add oil as necessary to bring the level to the upper mark on the
dipstick.
17.Dispose of used filter and oil properly.
-83-
Gearcases
Demand Drive Unit(Front Gearcase)
Always check and change engine oil at intervals outlined in the Periodic Maintenance Chart beginning on
page 72.
Refer to the Gearcase Specifications Chart on page 86 for
recommended lubricants, capacities and torque specifications.
Fill Plug
Fluid Check
The fill plug is located
On the bottom right side of the demand drive unit.Maintain the
fluid level even with the bottom thread of the fill plug hole.
1.Position the vehicle on a level surface.
2.Remove the fill plug.Check the fluid level.
3.Add the recommended fluid as needed.
4.Reinstall the fill plug.Torque specifications.
Fluid Change
The drain plug is located on the bottom of the gearcase.
1.Remove the fill plug.
Drain Plug
Front Gearcase
2.Place a drain pan under the drain plug.
3.Remove the drain plug.Allow the fluid to drain completely.
4.Clean the drain plug.
5.Reinstall the drain plug with new o-ring.Torque to specification.
6.Add the recommended fluid. Maintain the fouid level even with the bottom thread of the fill lpug hole.
7.Reinstall the fill plug with new o-ring.Torque to specification.
8.Check for leaks.Discard used fluid properly.
-84-
Gearcases
Rear Gearcase
Always check and change engine oil at intervals outlined in the Periodic Maintenance Chart beginning on
page 72.
FILL Plug
Refer to the Gearcase Specifications Chart on page 86 for
recommended lubricants, capacities and torque specifications.
Fluid Check
The fill plug is located On the right side of the rear gearcase.Maintain the
fluid level even with the bottom thread of the fill plug hole.
1. Position the vehicle on a level surface.
2. Remove the fill plug.Check the fluid level.
3. Add the recommended fluid as needed.
4. Reinstall the fill plug.Torque to specification.
Fluid Change
The drain plug is located on the bottom right side of the
rear gearcase.
1.Remove the fill plug.
Drain Plug
Rear Gearcase
2.Place a drain pan under the drain plug. Remove drain plug.
3.Allow the fluid to drain completely.
4.Clean the drain plug. Torque to specification.
5.Add the recommended fluid. Maintain the fouid level even with the bottom thread of the fill lpug hole.
6.Reinstall the fill plug.Torque to specification.
7.Check for leaks.Discard used fluid properly.
-85-
Gearcase
Gearcase Specification Chart
Use of other fluids may result in improper operation of components.
Gearcase
Lubricant
Capacity
Transmission of
Main Gearcase
(CF188-C)
preliminary:
2800ml
SAE15W/40 SG
change:2500ml
Transmission of
Transfer Case
(196S-C)
SAE15W/40 SG
330ml(preliminary),
280ml(change )
SAE15W/40 SG
or
SAE80W/90 GL-4
300ml(preliminary),
250ml(change )
Drain Plug/Level
Check Plug Torque
30 Nm
preliminary:
2800ml
change:2500ml
Demand Drive Unit SAE15W/40 SG
or
(Front Gearcase)
SAE80W/90 GL-4
Rear Gearcase
Fill Plug Torque
30 Nm
25Nm
25Nm
25Nm
25Nm
-86-
Spark Plugs
CAUTION
Using non-recommended spark plug can result in serious engine damage.
Always use CFMOTO-recommended spark plug. Refer to the specifications section beginning on page 120.
Spark Plug Gap/Torque
Model
Electrode Gap
New Plug Torque
Used Plug Torque
DPR7EA-9(NGK)
0.8-0.9mm
18Nm
18Nm
Spark plug condition is indicative of engine operation.The spark plug firing end condition should be read
after the engine is warmed-up and the vehicle is driven at higher speeds.Immediately check the spark plug for
correct color.See page 88.
A hot exhaust system and engine can cause serious burns. Wear protective gloves when removing a spark
plug for inspection.
-87-
Spark Plugs
Spark Plug Condition
Normal Plug
The normal insulator tip is gray, tan or light brown.There will be few combustion deposits. The electrodes are
not burned or eroded.This indicates the proper type and heat range for the engine and the service.
NOTE: The tip should not be white. A white insulator tip indicates overheating, caused by use of an improper
spark plug or incorrect throttle body adjustments.
Wet Fouled Plug
The wet fouled insulator tip is black. A damp oil film covers the firing end. There may be a carbon layer over
the entire nose.Generally, the electrodes are not worn.General causes of fouling are excessive oil, use of
non-recommended injection oil or incorrect throttle body adjustments.
Spark Plug Removal and Replacement
1. Remove both seats.
2. Remove the rear service panel. See page 34.
3. Remove the spark plug cap.
4. Using the spark plug wrench provided in the tool kit, remove the plug by rotating
it counterclockwise.
SPARK PLUG
5. Reverse the procedure for spark plug installation.
Torque to specification. See page 87.
-88-
Cooling System
Operation
The engine coolant level is controlled or maintained by the recovery system. The recovery system components are the overflow bottle, radiator filler neck, radiator pressure cap and connecting hose. As coolant operating temperature increases, the expanding (heated) excess coolant is forced out of the radiator, past the
pressure cap, and into the overflow bottle. As engine coolant temperature decreases, the contracting
(cooled) coolant is drawn back up from the tank, past the pressure cap, and into the radiator.
Adding or Changing Coolant
To ensure that the coolant maintains its ability to protect the engine, we recommend that the system be completely drained every two years and a fresh mixture of antifreeze and water added. We recommends the
use of 60/40 anti-freeze/coolant or a 50/50 mixture of high quality aluminum compatible anti-freeze/coolant
and distilled water.
Premium 60/40 is already premixed and ready to use. Do not dilute with water.
NOTE: Always follow the manufacturer's mixing recommendations for the freeze protection required in your
area.
Any time the cooling system has been drained for maintenance or repair, replace the coolant. If the recovery
bottle has run dry, the level in the radiator should be inspected. Add coolant as needed.
-89-
Cooling System
Radiator and Cooling Fan
Always check and clean the screen and radiator fins at the intervals outlined in the Periodic Maintenance
Chart beginning on page 72. Do not obstruct or deflect air flow through the radiator by installing unauthorized accessories in front of the radiator or behind the cooling fan. Interference with the radiator air flow can
lead to overheating and consequent engine damage.
CAUTION
Washing the vehicle with a high-pressure hose could damage the radiator
fins and impair the radiator's effectiveness. Using a high-pressure system is
not recommended.
-90-
Cooling System
Coolant Level
FILLER CAP
RESERVIOR
UPPER
Always check and change
LIMIT
the coolant at the intervals
outlined in the Periodic
LOWER
Maintenance Chart beginning
LIMIT
on page 72.
Maintain the coolant level between
the minimum and maximum
marks on the bottle
(when the fluid is cool).
1. Position the vehicle on
RADIATOR
a level surface.
ENGINE OIL RADIATOR
2. Remove the hood. See page 36.
3. View the coolant level in the overflow bottle.
4. If the coolant level is below the safe operating range, remove the
cap and use a funnel to add coolant through the opening. Reinstall the cap.
NOTE: If coolant must be added often, or if the overflow bottle runs completely
dry, there may be a leak in the system. Have the cooling system inspected by your dealer.
-91-
Cooling System
Radiator Coolant Level
Always check and clean the screen and radiator fins at the intervals outlined in the Periodic Maintenance
Chart beginning on page 72. Do not obstruct or deflect air flow through the radiator by installing unautho rized
accessories in front of the radiator or behind the cooling fan. InterInterference with the radiator air flow can
lead to overheating and consequentially, engine damage.
Escaping steam can cause severe burns. Never remove the pressure cap while the engine is warm or hot.
Always allow the engine to cool before removing the pressure cap.
1. Remove the hood. See page 36.
2. Slowly remove the radiator cap.
3. View the coolant level through the opening.
4. Use a funnel and slowly add coolant as needed.
NOTE: This procedure is required only if the cooling system has been drained
for maintenance and/or repair. But if the overflow bottle has run dry, the level in the radiator should also be
inspected.
NOTE: Use of a non-standard pressure cap will not allow the recovery system
to function properly. See your dealer for the correct replacement part.
-92-
Continuously Variable Transmission (CVT) System
Belt slip is responsible for creating excessive heat that destroys belts, wears clutch components and causes
outer clutch covers to fail. Switch
to low range while operating at slower speeds to extend the life of the CVT components (belt, cover, etc.).
Failure to comply with the instructions in this warning can result in severe injury or death.
Do not modify any component of the CVT system. Doing so may reduce its
strength so that a failure may occur at a high speed.
The CVT system has been precision balanced. Any modification will cause the system to be out of balance,
creating vibration and additional loads on components.
The CVT system rotates at high speeds, creating large amounts of force on
clutch components.
Extensive engineering and testing has been conducted
to ensure the safety of this product. However, as the owner, you have the following responsibilities to make
sure this system remains safe:
Always follow all recommended maintenance procedures. See your dealer as outlined in the owner's manual.
This CVT system is intended for use on CFMOTO products only. Do not install it in any other product.
Always make sure the CVT housing is securely in place during operation.
-93-
CVT System
CVT Drying
There may be some instances when water is accidently ingested into the CVT system. Use the following instructions to dry it out before operating.
1. Remove the seats. See page 34.
2. Loosen the lower screws that secure the clutch cover.
3. Allow the water to drain.
4. Tighten the screws.
5. Place the transmission in PARK. Apply the brakes.
6. Start the engine.
7. Apply varying throttle for 10-15 seconds to expel the moisture and
air-dry the belt and clutches. Do not hold the throttle wide open for more than 10 seconds.
8. Allow the engine RPM to settle to idle speed. Apply the brakes. Shift the transmission to the lowest available range.
9. Test for belt slippage. If the belt slips, repeat the process.
10. Take the vehicle to your dealer for service as soon as possible.
-94-
Filter Systems
Air Filter
Always change the air filter at the intervals outlined in the Periodic
Maintenance Chart beginning on page 72.
■Methods to clean or replace air filter element (see picture 2)
●Loosen fix clip 3, remove air filter element cap 2;
●Loosen screw 4, take down air filter element assy 5;
●Take out air filter element 6;
●Clean filter element 6 dust and oil stains with cleaner, dry out, soak filter
element 6 in engine oil, dry it properly; replace the filter element if it damaged;
reinstall filter element 6 and fix it into filter case 1;
●tighten screw 4 in turn, coat filter element cover 2, clamping clip 3.
Do not clean the air filter element with gas or low flash point
solvents.
●If the owner use different air filter from this owner's manual,
first the filter must be familiar with the engine's performance, so that
secure the engine performance, or else, the owner will be responsible for the
engine damage caused by improper filter, also the owner is responsible for
the filter cleaning, maintenance etc.
Attention! Cleaning the air filter elements and inner dirty per 100 hours. Shorten this cycle
when the filter working in dusty and moisture conditions. The filter element too dirty or
improper installment may shorten the engine lifetime.
-95-
Spark Arrestor
Failure to heed the following warnings while servicing the spark arrestor, could result in serious injury or death.
Do not perform clean-out immediately after the engine has been run, as the exhaust system becomes veryhot. Serious burns could result from contact with the exhaust components. Allow components to cool suffic
iently before proceeding.
Wear eye protection and gloves.
Never run the engine in an enclosed area. Exhaust contains poisonous carbon monoxide gas that can cause
loss of consciousness or death in a very short time.
Periodically clean the spark arrestor to remove accumulated carbon.
1.Remove the retaining screw and remove the
arrestor 1 from the end of the muffler 4.
2.Use a non-synthetic brush to clean the
arrestor screen. A synthetic
brush may melt if components are warm.
NOTE: If necessary, blow debris from the
screen with compressed air.
3.Inspect the screen for wear and damage. Replace a worn or
damaged screen.
4.Reinstall the arrestor. Torque screws 3 to:
6-8ft.lbs(8-10Nm)
-96-
Throttle
Failure to check or maintain proper operation of the throttle system can result
in an accident and lead to serious injury or death if the throttle pedal sticks during operation.
Never start or operate this vehicle if it has a sticking or improperly operating throttle pedal.
Immediately contact your dealer for service if throttle problems arise.
Always check the pedal for free movement and return before starting the engine and occasionally during
operation.
Throttle Freeplay
THROTTLE PEDAL
If the throttle pedal has excessive play due to cable stretch or misadjustment,
it will cause a delay in throttle response, especially at
low engine speed.The throttle may also not open fully. If the
throttle pedal has no freeplay, the throttle may be hard to
control,and the idle speed may be erratic. Check the throttle
pedal freeplay at the intervals outlined in the
Periodic Maintenance Chart beginning on page 72.
Adjust the freeplay if necessary.
Throttle Freeplay Inspection
1.Place the transmission in PARK.
2.Apply the brakes. Start the engine. Allow it to warm up
thoroughly.
3.Measure the distance the throttle pedal moves before the engine begins to pick up speed. Freeplay
should be 1/16 to 1/8inches(1.6-3.2mm)
-97-
Throttle System
Throttle Body/Idle RPM
Idle RPM is preset by the manufacturer. If the engine idle speed is not satisfactory, please see your dealer
for adjustment.
Throttle Freeplay Adjustment
THROTTLE CABLE
1.Remove both seats. Remove the rear service
panel. See page 34.
2.Locate the throttle cable adjuster.
3.Squeeze the end of the rubber boot and slide it far
enough to expose the end of the inline cable adjuster.
4.Loosen the adjuster lock nut.
5.Rotate the boot to turn the adjuster until
SHEATH
1/16" to 1/8"(1.6-3.2mm)of freeplay is
achieved at the throttle pedal. See page 97.
NOTE: While adjusting, lightly flip the throttle pedal up and down.
6.Tighten the lock nut.
7.Squeeze the end of the rubber boot and slide it over the cable
adjuster to its original position.
LOCK NUT
ADJUST NUT
-98-
Brakes
The front and rear brakes are hydraulic disc type brakes activated by the
brake pedal. See page 43.
Always check brake pedal travel and the brake fluid reservoir level
before each use of the vehicle.
When applied, the brake pedal should
feel firm. Any sponginess would indicate a possible fluid leak or low
brake fluid level, which must be corrected before riding.
See page 100
for brake fluid information.
If you discover any irregularities in brake system operation, including
excessive pedal travel, contact your dealer for proper diagnosis and repairs.
Operating the vehicle with a spongy brake pedal can result in loss of braking,
which could cause an accident resulting in severe injury or death. Never
operate the vehicle with a spongy-feeling brake pedal.
-99-
Brakes
Brake Fluid
Inspect the level of the brake fluid before each operation. If the fluid level is low add DOT 4 brake fluid only.
Change the brake fluid every two years and any time the fluid becomes contaminated, the fluid level is below
the minimum, or if the type and brand of the fluid in the reservoir are unknown. Access the brake fluid
reservoir
through the left front wheel well.
1.Position the vehicle on a level surface.
2.Place the transmission in PARK.
3.View the brake fluid level in the reservoir. The level should be between the maximum and minimum level
lines.
4.If the fluid level is lower than the lower level line, add brake fluid to the upper line.
5.Apply the brake forcefully for a few seconds and check for fluid leakage around the fittings.
After opening a bottle of brake fluid, always discard any unused portion. Never store or use a partial bottle.
Brake fluid is hygroscopic, meaning it rapidly absorbs moisture from the air. The moisture causes the boiling
temperature of the brake fluid to drop, which can lead to early brake fade and the possibility of accident or
severe injury.
-100-
Brake Inspection
1. Check the brake system for fluid leaks.
2. Check the brake pedal for excessive travel or a spongy feel.
3. Check the friction pads for wear, damage and looseness.
4. Inspect the brake pad wear surface for excessive wear.
5. Change pads when worn to 3/64" (1 mm).
Steering Wheel Inspection
Check the steering wheel for specified freeplay and smooth operation at the intervals outlined in the Periodic
Maintenance Chart beginning on page 74.
1. Position the vehicle on level ground.
2. Lightly turn the steering wheel left and right.
3. There should be 0.8"-1.0" (20- 2 5 mm) of freeplay.
4. If there is excessive freeplay or strange noises, or the steering feels rough or "catchy," have the steering
system inspected by an authorized CFMOTO dealer.
-101-
Suspension Adjustment
The front and rear suspensions are preload adjustable, with five
settings on each axle.
Adjustment Cam
Highest Setting
Lowest Setting
The suspensions are set on the lowest (softest) setting at the factory. This setting is appropriate for nearly
all riding conditions. Since the vehicle is equipped with full skid plates, suspension adjustment is not
necessary.
If desired, the suspension may be adjusted to maintain vehicle clearance height when carrying loads. Please
see your CFMOTO dealer for the tool required to make suspension adjustments. Elevate the vehicle slightly
for easier adjustment.
Always heed the following rules if you make adjustments to this suspension.
Always return the suspension to the lowest ( softest) setting after the load is removed from the vehicle.
The increased suspension height will negatively impact vehicle stability when operating without a load.
Always apply the same adjustment setting to all four wheels.
Never operate the vehicle on the highest (stiffest) or second highest preload settings without a total
combined payload
in the vehicle of 450 lbs. ( 204 kg) or more. Payload includes the driver, passenger, CFMOTO approved
accessories and cargo. Never exceed the stated load capacity for this vehicle. See page 120.
-102-
Tires
Operating your vehicle with worn tires will increase the possibility of skidding, loss of control and an accident,
which could result in serious injury or death.
Always replace tires when the tread depth measures 1/8" (3 mm) or less. Improper tire inflation or the use
of non- standard size or type of tires may adversely affect vehicle handling, which could result in
vehicle damage or personal injury. Always maintain proper tire pressure. When replacing tires, always
use original equipment size and type.
Tire Tread Depth
Always replace tires when tread depth is worn to 1/8" (3 mm) or less.
Axle and Wheel Nut Torque Specifications
Inspect the following items occasionally for tightness, and
if they've
been loosened for maintenance service.
75Nm
Cast Aluminum
Wheel Type
75Nm
Steel
Nut Type
Rim (Aluminum) Nut
Rim (Steel)
Nut
Any
Whe el Se at Su pport Re taining Nu t
NOTE:
-103-
Location
Front and Rear
Front and Rear
Front and Rear
Do not lubricate the stud or the lug nut.
Nut Torque
75Nm
75Nm
120Nm
Tires
Improperly installed wheels can adversely affect tire wear and vehicle
handling, which can result in serious injury or death. Always ensure that all nuts are torqued to specification.
Do not service axle nuts that have a cottepin installed. See your dealer.
Wheel Removal
1. Position the vehicle on a level surface.
2. Place the transmission in PARK.Stop the engine.
3. Loosen the wheel nuts slightly.
4. Elevate the side of the vehicle by placing a suitable stand under the
frame.
5. Remove the wheel nuts and washers.
Remove the wheel.
Steel rim
Wheel Installation
1. Place the transmission in PARK.
2.Place the wheel in the correct position on the
wheel hub. Be sure the valve stem is toward the
outside and rotation arrows on the tire point toward
forward rotation.
3.Attach the wheel nuts and washers and finger
tighten.
4.Carefully lower the vehicle to the ground.
5.Torque the wheel nuts to specification.
See page 103.
Alum allov rim
-104-
Lights
When servicing a halogen lamp, don't touch the lamp with bare fingers.
Oil from your skin leaves a residue, causing a hot spot that will shorten
the life of the lamp.
Poor lighting while driving can result in severe injury or death. Headlight and taillight lenses become
dirty during normal operation. Wash the headlights frequently to maintain lighting quality.Hot components can cause serious burns to skin. Do not service the headlamps until they've cooled sufficiently.
Headlight Lamp Replacement
1.Unplug the headlamp from
the wiring harness. Be sure
Headlamp rear cover
to pull on the connector, not
on the wiring.
2. Turn the lamp counterclockwise to remove it.
3. Install the new lamp1.
NOTE: Make sure the tab on the lamp locates properly
in the housing.
4. Reinstall the harness assembly into the head
light assembly.
Bolt
-105-
Tab
Dust cover
Lamp
Lights
Headlight Beam Adjustment
1.Place the vehicle on a level surface with the headlight approximately 25 ft. (7.6 m) from a wall. Place the transmission in PARK.
2. Measure the distance from the floor to the center of the headlight
and make a mark on the wall at the same height.
3. Apply the brakes. Start the engine. Turn on the headlights.
4. Observe the headlight aim. The most intense part of the headlight
beam should be aimed 8" (20 cm) below the mark placed on the
wall in step 2.
NOTE: Include the weight of a rider on the seat while performing this step.
5. If adjustment is necessary, turn the headlight adjustment screw to
adjust the beam.
6. Repeat steps 4-5 until the beam is properly adjusted.
-106-
Lights
Brake Lights
When the brake pedal is depressed, the brake light comes on. Check the
brake light before each ride.
1. Turn the ignition switch to the ON position.
2. Apply the brakes. The brake light should come on after about 10
mm (0.4 in.) of pedal travel. If the light doesn't come on, check the
bulb.
Vehicle Immersion
CAUTION
If your vehicle becomes immersed, major engine damage can result if the machine is not thoroughly inspected.
Take the vehicle to your dealer before starting the engine.
If it's impossible to take your vehicle to a dealer before starting it, follow the steps outlined below.
1. Move the vehicle to dry land.
2. Check the air box. If water is present, dry the air box and replace the
filter with a new filter. Thoroughly dry the air pre-filter. See page 100.
3. Remove the spark plugs.
4. Turn the engine over several times.
5. Dry the spark plugs and reinstall them, or install new plugs.
NOTE: Attempt to start the engine. If necessary, repeat the drying procedure.
6. Take the vehicle to your dealer for service as soon as possible, whether you succeed in starting it or not.
NOTE: If water has been ingested into the PVT follow the procedure on page
100 for drying.。
-107-
Battery
Your vehicle may have either a sealed battery, which requires little maintenance, or a conventional
battery. A sealed battery can be identi fied by its flat covers on the top of the battery. A conventional
batteryhas six filler caps on the top of the battery.Always keep battery terminals and connections
free of corrosion. If cleaning is necessary, remove the corrosion with a stiff wire brush. Wash with a
solution of one tablespoon baking soda and one cup water. Rinse well with tap water and dry off with
clean shop towels. Coat the terminals with dielectric grease or petroleum jelly. Be careful not to allow
cleaning solution or tap water into a conventional battery.
Battery electrolyte is poisonous. It contains sulfuric acid. Serious burns can result from contact with skin,
eyes or clothing.
Antidote:
External: Flush with water.
Internal: Drink large quantities of water or milk. Follow with milk of magnesia
beaten egg, or vegetable oil. Call physician immediately.
Eyes: Flush with water for 15 minutes and get prompt medical attention.
Batteries produce explosive gases. Keep sparks, flame, cigarettes, etc.
away. Ventilate when charging or using in an enclosed space. Always shield
eyes when working near batteries. KEEP OUT OF REACH OF CHILDREN.
-108-
Battery
Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or
death. When removing the batter always disconnect the negative (black) cable first. When reinstalling the
battery, always connect the negative (black) cable last.
Battery Removal
1. Remove the driver's seat. See page 34.
2. On conventional batteries, remove the battery vent tube.
3. Disconnect the black (negative) battery cable
first.
4. Disconnect the red (positive) battery cable
last.
5. Lift the battery out of the vehicle. Be careful
not to tip a conven-tional battery sideways,
which could spill electrolyte.
。
Anode (black)
Cathode(red)
Storage battery
CAUTION
If electrolyte spills, immediately wash it off with a solution of one tablespoon baking soda and one cup water
to prevent damage to the vehicle.
-109-
BatteryBattery
Installation
Using a new battery that has not been fully charged can damage the bat-tery and result in a shorter life.
It can also hinder vehicleperformance.
Follow the battery charging instructions on page 117 before installing the battery.
1. Ensure that the battery is fully charged.
2. Place the battery in the battery holder.
3. On conventional batteries, install the battery vent tube (sealed bat-teries do not have a vent tube).
NOTE: The vent tube must be free of obstructions and securely installed.
Route the tube away from the frame and vehicle body to prevent contact with electrolyte.
Battery gases could accumulate in an improperly installed vent tube and cause an explosion, resulting
in serious injury or death. Always ensure that the vent tube is free of obstructions and is securely
installed as recommended.
4. Coat the terminals with dielectric grease or petroleum jelly.
5. Connect and tighten the red (positive) cable first.
6. Connect and tighten the black (negative) cable last.
7. Verify that cables are properly routed.
8. Reinstall the driver's seat.
-110-
Battery
Battery Storage
Whenever the vehicle is not used for a period of three months or more,
remove the battery from the vehicle, ensure that it's fully charged, and
store it out of the sun in a cool, dry place. Check battery voltage each
month during storage and recharge as needed to maintain a full charge.
See page 112.
NOTE: Battery charge can be maintained by using a CFMOTO Battery Tender
charger or by charging about once a month to make up for normal selfdischarge. Battery Tender can be left connected during the storage
period, and will automatically charge the battery if the voltage drops
below a pre-determined point.
Battery Fluid
A poorly maintained battery will deteriorate rapidly. Check the battery fluid level often. Battery vol:
12V 18Ah
-111-
Battery
Battery Charging (Conventional Battery)
1. Remove the battery from the vehicle to prevent damage from leaking or spilled electrolyte during charging. See page 109.
2. Charge the battery with a charging output no larger than 1/10 of the battery's amp/hr rating.
Charge as needed to raise the specific grav-ity to 1.270 or greater.
3. Reinstall the battery. See page 110.
Battery Charging (Sealed Battery)
The following battery charging instructions apply only to the installa-tion of a sealed battery.
Read all instructions before proceeding with the installation of this battery.
The sealed battery is already filled with electrolyte and has been sealed
and fully charged at the factory. Never try the sealing strip off or add
any other fluid to this battery.
The single most important thing about maintaining a sealed battery is to
keep it fully charged. Since the battery is sealed and the sealing strip
cannot be removed, you must use a voltmeter or multimeter to measure
DC voltage.
An overheated battery may explode, causing severe injury or death. Always watch charging times carefully.
Stop charging if the battery becomes very warm to the touch. Allow it to cool before resuming charging.
For a refresh charge, follow all instructions carefully.
1. Check the battery voltage with a voltmeter or multimeter. A fully
charged battery will register 12.8 V or higher.
2. If the voltage is less than 12.8 volts, recharge the battery at 1.2 amps
or less until battery voltage is 12.8 or greater.
NOTE: When using an automatic charger, refer to the charger manufacturer's
instructions for recharging. When using a constant current charger,
use the guidelines on the next page for recharging.
-112-
Battery
Battery Charging (Sealed Battery)
NOTE: Always verify battery condition before and 1-2 hours after the end of charging.。
State of Charge
100%
-113-
Voltage
12.8-13.0V
75%-100%
12.5-12.8V
50%-75%
12.0-12.5V
25%-50%
11.5-12.0V
Action
Charge Time
None, check at 3
None required
mos. from date of
manufacture
None required
May need slight charge,
if no
charge given,
check in 3 months
3-6 hours
Needs charge
5-11hours
Needs charge
At least 13 hours,
verify state of charge
Cleaning and Storage
Washing the Vehicle
Keeping your vehicle clean will not only improve its appearance
but it can also extend the life of various components.
CAUTION
High water pressure may damage components.CFMOTO recommends washing the vehicle by hand or with
a garden hose, using mild soap. Certain products, including insect repellents and chemicals, will
damage plastic surfaces.
Do not allow these types of products to contact the vehicle.。
The best and safest way to clean your vehicle is with a garden
hose and a pail of mild soap and water.
1. Use a professional-type washing cloth, cleaning the upper body first
and the lower parts last.
2. Rinse with clean water frequently.
3. Dry surfaces with a chamois to prevent water spots.
Washing Tips
* Avoid the use of harsh cleaners, which can scratch the finish.
* Do not use a power washer to clean the vehicle.
* Do not use medium to heavy duty compounds on the finish.
* Always use clean cloths and pads for cleaning and polishing. Old or
reused cloths and pads may contain dirt particles that will scratch the finish.
-114-
Cleaning and Storage
Washing the Vehicle
If a high pressure water system is used for cleaning (not recommended),
exercise extreme caution. The water may damage components and could
remove paint and decals. Avoid directing the water stream at the following items:
* Wheel bearings
* Radiator
* Transmission seals
* Brakes
* Cab and body panels
* Labels and decals
* Electrical components and wiring
NOTE: If warning and safety labels are damaged, contact your CFMOTO deal
for free replacement.
Grease all zerk fittings immediately after washing. Allow the engine
run for a while to evaporate any water that may have entered the engine
or exhaust system.
Polishing the Vehicle
CFMOTO recommends the use of common household aerosol furniture
polish for polishing the finish on your CFMOTO vehicle. Follow the
instructions on the container.
Polishing Tips
* Avoid the use of automotive products, some of which can scratch the
finish of your vehicle.
* Always use clean cloths and pads for cleaning and polishing. Old or
reused cloths and pads may contain dirt particles that will scratch the finish.
-115-
Cleaning and Storage
Chrome Wheel Care (if equipped)
Proper maintenance will protect chrome wheels from corrosion, preserve wheel life and ensure a “like new” appearance for many years.
NOTE: Chrome wheels exposed to road salt (or salt in the air in coastal areas)
are more susceptible to corrosion if not properly cleaned. Clean
chrome wheels more often if they're exposed to salt or other corrosive
elements.
1. Wash chrome wheels frequently. Use a mild detergent. Never use
abrasive cleaners on plated or painted surfaces.
2. Rinse well with clear water. Soap, detergents, salt, dirt, mud and
other elements can cause corrosion.
3. Polish the clean chrome wheels periodically. Use an automotive
grade chrome polish.
4. Routinely and liberally apply a weather resistant wax to each polished chrome wheel. Choose a product suitable for chrome finishes.
Read and follow the product labels and instructions.
Removing Corrosion
If light rust is found on the chrome finish, use steel wool (#0000-OTT
grade) to remove it. Gently rub the affected areas with the steel wool
until the corrosion has been removed. Clean and polish the wheel as outlined above.
-116-
Cleaning and Storage
Storage Tips
CAUTION
Starting the engine during the storage period will disturb the protective film
created by fogging and damage could occur. Never start the engine during
the storage period.
lean the Exterior
Make any necessary repairs and clean the vehicle as recommended. See page 114.
Stabilize the Fuel
1. Fill the fuel tank.
2. Add CFMOTO Carbon Clean Fuel Treatment or CFMOTO Fuel Stabilizer.
Follow the instructions on the container for the recommended amount.
NOTE: Carbon Clean removes water from fuel systems, stabilizes fuel and
removes carbon deposits from pistons, rings, valves and exhaust sys tems.
3. Allow the engine to run for 15-20 minutes to allow the stabilizer to
disperse through the entire fuel delivery system.
Oil and Filter
Change the oil and filter. See page 83.
Air Filter / Air Box
Inspect and clean or replace the pre-filter and air filter. See page 83.
Clean the air box. Drain the sediment tube.
Fluid Levels
Inspect the fluid levels. Add or change fluids as recommended in the
Periodic Maintenance Chart beginning on page 95
* Demand drive fluid (front gearcase)
* Rear gearcase fluid
* Transmission fluid
* Brake fluid (change every two years and any time the fluid looks dark or contaminated)
* Coolant (test strength/fill)
-117-
Cleaning and Storage
Storage Tips
Inspect and Lubricate
Inspect all cables and lubricate all areas of the vehicle as recommended in the Periodic Maintenance Chart
beginning on page 72.
Fog the Engine
1. Treat the fuel system with CFMOTO Carbon Clean. Follow the instructions on the container. Start the
engine. Allow it to idle for several minutes so the Carbon Clean reaches the injectors. Stop the engine.
2. Remove the spark plugs and add 2-3 tablespoons of Premium 4 Synthetic 0W40 engine oil. To access the
plug holes, use a section of clear 1/4" hose and a small plastic squeeze bottle filled with the premeasured
amount of oil.
NOTE: Do this carefully! If you miss the plug holes, oil will drain from the spark plug cavities into the hole at
the front of the cylinder head, and appear to be an oil leak.
3. Reinstall the spark plugs. Torque to specification.
4. Apply dielectric grease to the inside of each spark plug cap. Do not reinstall the caps onto the plugs at this
step.
5. Turn the engine over several times. Oil will be forced in and around the piston rings and ring lands, coating
the cylinder with a protective film of fresh oil.
6. If CFMOTO fuel system additive is not used, fuel tank, fuel lines, and injectors should be completely drained of gasoline.
7. Reinstall the spark plug caps to the spark plugs.
Battery Maintenance
See pages 110-112 for storage and charging procedures.
Storage Area/Covers
Be sure the storage area is well ventilated.
NOTE: Do not use plastic or coated materials. They do not allow enough ventilation to prevent condensation,
and may promote corrosion and oxidation.
-118-
Cleaning and Storage
Removal from Storage
1. Check the battery electrolyte level and charge the battery if necessary.
Install it in the vehicle. Make sure the battery vent hose is routed properly and that it's not pinched or
restricted in any way.
2. Make sure the spark plug is tight.
3. Fill the fuel tank with fuel.
4. Check all the points listed in the Daily Pre-Ride Inspection section on page 56.
NOTE: Tightness of the bolts, nuts and other fasteners should be checked by an authorized CFMOTO dealer.
5. Lubricate at the intervals outlined in the Periodic Maintenance
Chart beginning on page 72.
Engine exhaust contains poisonous carbon monoxide and can cause loss of consciousness or death. Never
run an engine in an enclosed area.
Transporting the Vehicle
Follow these procedures when transporting the vehicle.
1. Place the transmission in PARK. Stop the engine.
2. Remove the key to prevent loss during transporting.
3. Secure the fuel cap and seats.
4. Always tie the frame of the CFMOTO vehicle to the transporting unit securely with suitable straps or rope.
Do not attach tie straps to the front control arm bolt pockets.
-119-
SPECIFICATIONS
Item
CF625- 3
CF500- 6
Gross Vehicle Weight
495kg( With full Engine Oiland fuel )
495kg(With full Engine Oil and fuel )
Fuel Capa city
27L
27L
Engine Oil Capacity
2800ml(first time ),2500ml( replace) 2800ml( first time ),
2500ml( replace)
Coolant Capacity
2720ml
2720ml
Rear Gearcase Oil Capacity
300ml( first time ), 250ml(replace)
300ml(first time) , 250ml(replace)
Transfer Case Oil Capyacit
330ml( first time ), 280ml( replace)
330ml( first time ), 280ml( replace)
L oadable Weight Capacity
100kg
100kg
Maximum Weight Capacity
250kg(riders/cargo/accessories)
250kg(riders/cargo/accessories)
(Payload)
Receiver Hitch Tongue Capacity 50kg
50kg
Receiver Hitch Towing Capacity
125kg(including trailer and cargo)
125kg(including trailer and cargo)
Overall Length
2630mm
2630mm
Overall Width
1320mm
1320mm
Overall Height
1800mm
1800mm
Wheelbase
1960mm
1960mm
M inimum turning radius
5.0m
5.0m
Ground Clearance
240mm
240mm
-120-
Item
ENGINE NO.
ENGINE TYPE
Displacement
Bore x Stroke
Alternator Output
Compression Ratio
CF625-3
CF500-6
196S-C
CF188-C
Single cylinder、4 valve 4 stroke with
counterbalance
Single cylinder、4 valve 4 stroke with
counterbalance
594ml
493ml
87.5mm×82mm
300W,5000 r/min
96mm×82mm
300W,5000 r/min
10:1
Electric
10.2:1
Starting System
Fuel System
Ignition System
EFI(Electronic fuel injection)
ECU
EFI(Electronic fuel injection)
ECU
Spark Plug / Gap
NGK:DPR7EA-9/0.8-0.9
NGK:DPR7EA-9/0.8-0.9
Front Suspension
Independent double arm
Independent double arm
Rear Suspension
Independent double arm
Independent double arm
Lubrication System
Compression Wet Sump
Compression Wet Sump
Engine Oil
SAE15W/40 SG
SAE15W/40 SG
Driving System Type
Front/Rear gear output
Shift Type
Dual Range/L-H-N-R
Front/Rear gear output
Dual Range/L-H-N-R
Gear Reduction - Low
Gear Reduction – Reverse
Gear Reduction - High
5.857
3.828
3.514
5.857
3.828
3.514
-121-
Electric
Item
Drive Ratio - Front
Drive Ratio - Final
CF500-6
CF625-3
3.667(33/9)
3.667(33/9)
3.667(33/9)
3.667(33/9)
25×8-12 77J
25×8-12 77J
205/80-12 77J
205/80-12 77J
25×10-12 85J
25×10-12 85J
255/65-12 85J
255/65-12 85J
Tire Pressure - Front
70kPa
70kPa
Tire Pressure - Rear
84kPa
84kPa
Brakes, Front/Rear
Foot Activated, 4-wheel hydraulic disc
Foot Activated, 4-wheel hydraulic disc
Front trunk Loadable
10kg
10kg
Headlight
35W/35W×2
35W/35W×2
Brake light/Tail light
21W/5W×2
21W/5W×2
Front turning light
21W×2
21W×2
Rear turning light
10W×2
10W×2
Front position light
5W×2
5W×2
Dashboard
LCD Dashboard
LCD Dashboard
Auxiliary DC Outlet
12V Maximal current:10A
12V Maximal current:10A
Tire Size - Front
Tire Size - Rear
-122-
Drive Belt Wear/Burn
TROUBLESHOOTING
Solution
Possible Cause
Slow/easy clutch engagement
Use low range during loading.
Use low range. See warnings on page 63.
Drive at a higher speed or use low range more frequently.
See page 43
Warm the engine at least 5 minutes. With the transmission in
neutral, advance the throttle to about 1/8 throttle in short bursts,
5 to 7 times. The belt will become more flexible and prevent belt
burning.
Use the throttle quickly and effectively.
Towing/pushing at low RPM/low ground speed
Use low range only.
Utility use/plowing
Use low range only.
Stuck in mud or snow
Shift the transmission to low range and carefully use fast,
aggressive throttle application to engage clutch.
WARNING: Excessive throttle may cause loss of control and
vehicle overturn
Climbing over large objects from a stopped
position
Shift the transmission to low range and carefully use fast, brief,
aggressive throttle application to engage clutch.
WARNING: Excessive throttle may cause loss of control
and vehicle overturn.
Belt slippage from water or snow ingestion into
the PVT system
Dry out the PVT. See page 95. Inspect clutch seals for
damage if repeated leaking occurs.
Clutch malfunction
See your dealer.
Check for fouled plugs or foreign material in gas tank or fuel
lines. See your dealer.
Always warm up the belt by operating below 30 mph for
one mile (5 miles or more when temperature is below freezing).
Driving onto a pickup or tall trailer in high range
Starting out going up a steep incline
Driving at low RPM or ground speed (3-7 MPH)
Insufficient warm-up at low ambient temperatures
Poor engine performance
Slippage from failure to warm up belt
-123-
Drive Belt Wear/Burn
Possible Cause
Wrong or missing belt
mproper break-in
Solution
Install the recommended belt.
Always break in a new belt and/or clutch. See
pages 53 and 43.
Engine Doesn't Turn Over
Possible Cause
Solution
Low battery voltage
Recharge the battery to 12.8 VDC
Loose battery connections
Check all connections and tighten
Loose solenoid connections
Loose electronic control box connections
Check all connections and tighten
Inspect, clean, reinstall connectors
Engine Turns Over, Fails to Start
Possible Cause
Out of fuel
Clogged fuel filter
Water is present in fuel
Old or non-recommended fuel
Fouled or defective spark plugs
Water or fuel in crankcase
Low battery voltage
Mechanical failure
Solution
Refuel
See your CFMOTO dealer
Drain the fuel system and refuel
Replace with fresh recommended fuel
Inspect plugs and replace if necessary
Immediately see your CFMOTO dealer
Recharge the battery to 12.8 VDC
See your dealer
-124-
Engine Backfires
Possible Cause
Solution
Weak spark from spark plug
Incorrect spark plug gap or heat range
Inspect, clean and/or replace spark plugs
Old or non-recommended fuel
Replace with fresh recommended fuel
Set gap to specs or replace plugs
Incorrectly installed spark plug wires
See your dealer
Incorrect ignition timing
See your dealer
Mechanical failure
See your dealer
Loose ignition connections
Check all connections and tighten
Water present in fuel
Replace with fresh recommended fuel
Engine Pings or Knocks
Possible Cause
Poor quality or low octane fuel
ncorrect ignition timing
Incorrect spark plug gap or heat range
-125-
Solution
Replace with recommended fuel
See your dealer
Set gap to specs or replace plugs
Engine Runs Irregularly, Stalls or Misfires
Possible Cause
Solution
Fouled or defective spark plugs
Worn or defective spark plug wires
Inspect, clean and/or replace spark plugs
Incorrect spark plug gap or heat range
Set gap to specs or replace plugs
Loose ignition connections
Check all connections and tighten
Water present in fuel
Replace with new fuel
Low battery voltage
Recharge battery to 12.8 VDC
Kinked or plugged fuel tank vent line
Inspect and replace
Incorrect fuel
Replace with recommended fuel
Clogged air filter
Inspect and clean or replace
Other mechanical failure
See your dealer
Low or contaminated fuel
Add or change fuel, clean the fuel system
Low octane fuel
Replace with recommended fuel
Clogged fuel filter
See your CFMOTO dealer
Fuel is very high octane
Replace with lower octane fuel
See your dealer
-126-
Engine Stops or Loses Power
Possible Cause
Out of fuel
Kinked or plugged fuel vent line
Water is present in fuel
Fouled or defective spark plugs
Worn or defective spark plug wires
Incorrect spark plug gap or heat range
Solution
Refuel
Inspect and replace
Replace with new fuel
Inspect, clean and/or replace spark plug
See your dealer
Loose ignition connections
Set gap to specs or replace plug
Check all connections and tighten
Low battery voltage
Recharge the battery to 12.8 VDC
Incorrect fuel
Replace with fresh recommended fuel
Clogged air filter
Inspect and clean or replace
Other mechanical failure
See your dealer
verheated engine
Clean radiator screen and core, clean engine
exterior, see your dealer
-127-
GEAR SENSOR
FUEL PUMP RELAY
DIMMER SWITCH TURNING SWITCH
BRAKE RELAY
IGNITION SWITCH
LOWBEAM RELAY
SHUT OFF SWITCH HORN SWITCH
HIGHBEAM RELAY FAN RELAY
FLASHER HORN FUSE BOX
OVER RIDE SWITCH
L H N
REVERSE GEAR SENSOR
AUXILIARY RELAY IV
PAR K BRAK E SW ITCH
ALARM SIGNAL SWITCH
ILLUMINATION SWITCH
START RELAY&FUSE
AUXILIARY RELAY III
BATTERY
REGULATOR
RECTIFIER
CLOCK BUTTON SWITCH
START MOTOR
SPEEDOMETER
FUEL GAGUE
ODOMETER SENSOR
TURNNING SLGNAL RH
WATER TEMPERATUURE GAGUE
TURNNING SLGNAL LH
FUEL SENSOR
POSITION INDICATOR
2WD,4WD,4WD
DEAD LOCK INDICATOR
REAR TURNING SIGNAL RH
TROUBLE LAPM
COLOCK
TAIL/BRAKE LIGHT
BEAM
REAR TURNING SIGNAL LH
LINDICATOR
HINDICATOR
TAIL/BRAKE LIGHT
NINDICATOR
PINDICATOR
RINDICATOR
OVER RIDE INDICATOR
REAR LICENSE PLATE LIGHT
FRONT TURNING LIGHT RH
HEADLIGHT RH
FRONT PILOT LIGHT RH
FRONT TURNING SIGHAL LH
HEAD LIGHT LH
FRONT PILOT LIGHT LH
CIGAR LIGHTEER
IAR PRESSURE
DIAGNOSTIC SYSTEM
OIL ATOMIZER GEAR SENSOR
SENSOR
OXYGEN SENSOR
3 PHASE IMAGNETO
THROTTLE POSITION SENSOR IDLE SPEED CONTROL VALVE
AIR TEMPERATUPE
SENSOR
IGNITION COIL AND SPARK PLUG
WATER TEMPERATURE SENSOR
OIL FUEL PUMP
THERMOSWITCH
FAN&MOTOR
AUXILIARY RELAYI AUXILIARY RELAYI
FRONT BRAKE SWITCH
2WD,4WD,4WD
DEADLOCK TRANSITION MOTOR
2WD,4WD,4WD
DEADLOCK TRANSITION MOTOR
CODE
COLOR
RED
RED/
WHITE
BLACK
BLACK/
WHITE
BLACK/
BLACK/
YELLOW BROWN
BLACK/
BLUE
BLACK/
RED
GREEN
GREEN/
RED
GREEN/ GREEN/ GREEN/ GREEN/
YELLOW BLACK WHITE BLUE
GREY/
RED
GREY/
WHITE
GREY/
BLACK
BROWN
BROWN/ BROWN/ BROWN/ BROWN/ BROWN/
BLUE
RED
GREEN WHITE
BLACK
BLUE
BLUE/
RED
BLUE/
BLACK
LIGHT/
GREEN
LIGHT GREEN
/RED
BLUE/
WHITE
BLUE/
GREEN
ORANGE ORANGE ORANGE/ ORANGE/
BLUE
/BLACK WHITE
WHITE
WHITE/ WHITE/
YELLOW BLUE
WHITE/
BROWN
WHITE/
GREEN
LIGHT GREEN/
BLUE
LIGHT/
BLUE
LIGHT BLUE/
WHITE
WHITE/
BLACK
COLOR
LIGHT GREEN/
PINK
P
COLOR
YELLOW YELLOW YELLOW YELLOW
YELLOW /WHITE /RED
/BLUE
/BLACK
GREY
LIGHT GREEN/
GREEN
LIGHT GREEN/
YELLOW
LIGHT GREEN/
BROWN
PURPLE
China
EU1004