Vitek VTC-IRE70 Specifications
Add to my manuals24 Pages
Vitek VTC-IRE70 is a high-resolution camera that delivers crystal clear images with 700TVL resolution, capturing every detail. Its Sony 960H EX-view CCD and Effio-E image signal processors ensure accurate color reproduction, even in scenes with high spatial frequency. The 2D noise reduction signal processing reduces noise and enhances image quality, while the Advanced IR Optimizer helps prevent over-saturation of IR-illuminated video. With 70 Infrared LEDs and Infrared LED Dynamic Intensity Control, the camera provides clear vision in total darkness up to 300 feet.
advertisement
VTC-IRE70/650
Long Range IR Bullet Camera
• High Density 1/3” EX-VIEW CCD & Effio-E DSP
• 700TVL High Resolution
• Advanced IR Optimizer helps reduce over saturation of IR illuminated video without engaging the Image Signal Processor chip.
• 70 Infrared LEDs at 850nm enable viewing in total darkness up to 300 feet
• Infrared LED Dynamic Intensity Control with Automatic Brightness Adjustment of IR LEDs to help prevent washed out images when objects are too close
• 0.003 Lux (F1.2 @ 40IRE) / 0 Lux with IR LEDs On
• E-WDR by Adaptive Tone Reproduction
• 6-50mm Varifocal Auto Iris IR Lens with External Adjustments for Focus and
Zoom
• True Day/Night by ICR - Infrared Cut Removal
• 2DNR Noise Reduction
• Motion Detection, Privacy Masking & Highlight Masking
• Dual Glass Compartments to Eliminate Glare
• OSD (On Screen Display) menu and Camera ID
• Secondary Video Output & OSD Control Joystick are accessible inside a gasket sealed removable side panel
• Gasket-sealed external focus and zoom controls with clutch mechanism to eliminate over-tightening for ease of installation and adjustment
• Heavy Duty IP68 rated weather/vandal resistant aluminum construction is
100% water and dust proof
• 24VAC/12VDC Dual Voltage
Table of contents
1. Safety Instructions and Notes ....................................................................................................................................................... 2
2. General Descriptions ......................................................................................................................................................................... 3
3. Supplied Items ..................................................................................................................................................................................... 3
4. Part names ............................................................................................................................................................................................. 4
5. Installation Instructions .................................................................................................................................................................. 5
5.1. Mounting The Camera ................................................................................................................................... 5
5.2. Power Supply Connections .......................................................................................................................... 5
6. Setup Menu ........................................................................................................................................................................................... 5
6.1
6.2
6.2.1
6.2.2
In the Menu ........................................................................................................................................................ 5
Main Menu .......................................................................................................................................................... 6
Main Menu-‐1 ...................................................................................................................................................... 6
Main Menu-‐2 ...................................................................................................................................................... 7
6.8
6.9
6.10
6.11
6.12
6.3
6.3.1
6.3.2
6.4
6.5
6.6
6.7
Shutter/AGC Menu .......................................................................................................................................... 7
Shutter/AGC> Auto Setup Menu ............................................................................................................... 8
Shutter/AGC> Manual Setup Menu .......................................................................................................... 9
Lens Menu ........................................................................................................................................................... 9
Day/Night Menu ............................................................................................................................................. 10
Picture Adjust Menu ...................................................................................................................................... 11
White Balance Menu ..................................................................................................................................... 12
ATR (Adaptive Tone Reproduction) Menu .......................................................................................... 13
Backlight Menu ................................................................................................................................................ 14
NR Menu ............................................................................................................................................................. 14
Motion Detection Menu ............................................................................................................................... 15
Privacy Menu .................................................................................................................................................... 16
6.13
6.14
6.15
Language Menu ............................................................................................................................................... 16
Camera ID Menu .............................................................................................................................................. 17
Camera Reset .................................................................................................................................................... 17
6.16 EXIT ...................................................................................................................................................................... 17
7. Specifications ...................................................................................................................................................................................... 18
8. Dimensional Drawings .................................................................................................................................................................... 19
1
WARNING
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.
This symbol is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
Caution
To prevent electric shock and risk of fire hazards, do NOT use other than specified power source.
Warning (NTSC version) -- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.
Caution -- Any changes or modifications in construction of this device that are not approved by the party responsible for compliance could void the user's authority to operate the equipment.
1. Safety Instructions and Notes
• Please read these safety and operating instructions before operating the camera.
• Keep the manual in a safe place for later reference.
• Pay attention to safety when laying the connection cable and observe that the cable is not subjected to
heavy loads, kinks, damage or moisture.
• Never open the device to expose boards or lenses. The warranty becomes void if repairs are undertaken
by unauthorized persons.
• Only authorized service centers may perform maintenance or repairs.
• Use only a mild detergent to clean the housing.
• Keep the window surface clean of dirt or dust, which may reflect infrared light into the lens at night.
• The camera should never be operated in an environment that exceeds the technical specifications,
as this may result in the destruction of the product and will also void the factory warranty.
2
2. General Descriptions
The VTC-IRE70/650 camera is an ultra high resolution camera that realizes over 700 TV Lines of resolution and delivers crisp color reproduction with its Sony 960H EX-view CCD and Effio-E image signal processors.
Effio-E digital imaging system:
•
Delivers crystal clear images with 700TVL resolution that accurately captures every aspect of any scene
•
Color signal processing provides the optimum balance between the luminance and chroma signals for high color reproducibility even for the detailed scenes that contain very high spatial frequency
• Incorporates 2D noise reduction signal processing
ICR mechanism:
•
Enhances its sensitivity about 10x at night
•
•
Accepts Infrared Light
24VAC/12VDC dual power design:
•
Offers the flexibility of installation
Ensures reliability
Main features:
• High Density 1/3” EX-VIEW CCD & Effio-E DSP
• 700TVL High Resolution
• Advanced IR Optimizer helps reduce over saturation of IR illuminated video without engaging the Image
Signal Processor chip.
• 70 Infrared LEDs at 850nm enable viewing in total darkness up to 300 feet
• Infrared LED Dynamic Intensity Control with Automatic Brightness Adjustment of IR LEDs to help prevent
washed out images when objects are too close
• 0.003 Lux (F1.2 @ 40IRE) / 0 Lux with IR LEDs On
• E-WDR by Adaptive Tone Reproduction
• 6-50mm Varifocal Auto Iris Lens with External Adjustments for Focus and Zoom
• True Day/Night by ICR - Infrared Cut Removal
• 2DNR Noise Reduction
• Motion Detection, Privacy Masking & Highlight Masking
• Dual Glass Compartments to Eliminate Glare
• OSD (On Screen Display) menu and Camera ID
• Secondary Video Output & OSD Control Joystick are accessible inside a gasket sealed removable side
panel
• Gasket-sealed external focus and zoom controls with clutch mechanism to eliminate over-tightening for
ease of installation and adjustment
• Heavy Duty IP68 rated weather/vandal resistant aluminum construction is 100% water and dust proof
• 24VAC/12VDC Dual Voltage
3. Supplied Items
• 1x VTC-IRE70/650 IR Bullet camera
• 1x Sunshield panel with attachment screw
• 1x 5mm Hex L-wrench (a)
• 1x 3mm Hex L-wrench (b)
• 4x Wall fixing screws (c) with 4x anchors (d)
• 1x Installation and Operating Instructions
• 1x Mounting template
• 1x Video Sub-out cable (e)
• 1x Mounting Plate (g) 4x Mounting Bolts (f)
3
4. Part Names
4.1 Front view ⓐ ⓑ ⓒ ⓐ Sunshield attachment thumb screw ⓑ IR LED Panel ⓒ Double Glass Window
4.2 Rear side view ⓓ Sunshield ⓔ OSD (On Screen Display Control) Cover ⓕ Arm Assembly ⓖ Mounting Bracket Foot
① Focus adjustment
② Zoom adjustment
① ② ⓓ ⓔ ⓖ ⓕ
4
5. Installation Instructions
• Make sure the power is not applied before installation.
• Once the camera is installed, you must first connect the low voltage (AC24V or DC12V). Then, plug the
AC adapter into the AC outlets to avoid an improper reset and damage from a possible surge voltage.
5.1. Mounting the camera on the wall
1) Drill 4 holes into the wall or ceiling using the supplied
template
2) Insert the anchors into the drilled holes
3) Match ( foot mount holes) to the drilled holes
4) Affix the mounting bracket by using supplied screws
5.2. Power Supply Connections
The VTC-IRE70/650 can operate with either 24AC or 12VDC, dual voltage power.
It is required that the polarity-matched connection is made for 12VDC supply, otherwise IR LEDs, will not operate at night.
Primary and secondary grounds are completely isolated to avoid possible ground-loop problems.
Clamp connectors of power input
AC24V/DC12V (RED WIRE)
AC24V/GND (BLACK WIRE)
6. SETUP Menu
6.1 In the Menu
The setup menu can be accessed and controlled with the OSD joy stick on the side of camera.
Five commands are available with the joy stick.
VIDEO
SUB-OUT connector
Joy stick
SYMBOL descriptions for joystick operation
1.
2.
▲
,
▼
,
◀
,
►
- Denotes the direction of Joystick lever operation.
●
- Denotes “ENTER” by pressing straight down on the Joystick lever
In the menu, use
▲
,
▼
to move menu,
◀
,
►
to change the settings and press ● to select or enter.
5
The FACTORY DEFAULT in this manual may NOT be the same as the default values set by the FACTORY due to feature improvements or customer requirements.
To enter menu, press ● when MENU is not active.
6.2 MAIN menu
Follow the chart for submenu settings.
MAIN menu-1 MAIN menu-2
6.2.1 MAIN menu-1
MAIN menu-1
SHUTTER
/AGC
LENS
DAY/NIGHT
PICT ADJUST
WHITE BAL
ATR
BACKLIGHT
NEXT
EXIT
Default
AUTO
AUTO
AUTO
-
ATW
OFF
OFF
SAVE ALL
Descriptions
Sets the parameters related to the shutter mode and AGC for AUTO and
MANUAL settings. See '6.3 SHUTTER/AGC menu' for details.
Selects the lens type, AUTO or MANUAL. AUTO supports DC auto-iris lens only. See '6.4 LENS menu' for details.
DAY/NIGHT mode for AUTO only with IR LED version.
AUTO – Camera switches DAY from/to NIGHT automatically by the built-in light sensor.
BURST, DELAY CNT, DAY→NIGHT, NIGHT→DAY can be set.
See '6.5 DAY/NIGHT menu' for details.
Sets MIRROR, BRIGHTNESS, CONTRAST, SHARPNESS, HUE or GAIN.
See '6.6 PICT ADJUST menu' for details.
Sets ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK.
See '6.7 WHITE BAL menu' for details.
Sets ON/OFF for enabling/disabling ATR (Adaptive Tone Reproduction) compensation for the better dynamic range (E-WDR) of the image.
See '6.8 ATR menu' to adjust the dynamic ranges.
Selects BACKLIGHT mode out of OFF, HLC or BLC. Areas and gains for
HLC and BLC are factory preset and not user adjustable.
Moves to MAIN menu-2.
Exits the setup menu. To save the changes, move cursor to 'SAVE ALL' and press ● button before exiting the setup menu
Saves all parameters by pressing ● button when cursor is on 'SAVE ALL'
6
6.2.2 MAIN menu-2
MAIN menu-2 Default
NR -
Descriptions
Sets the noise reduction parameters for NR MODE and Y LEVEL,
C LEVEL. See '6.9 NR menu' for details.
MOTION DET OFF
Sets ON/OFF for enabling/disabling MOTION DET.
See '6.10 MOTION DET menu' for the parameter settings.
PRIVACY OFF
Sets ON/OFF for enabling/disabling PRIVACY.
See '6.11 PRIVACY menu' for the parameter settings.
LANGUAGE ENGLISH
CAMERA ID OFF
CAMERA
RESET
BACK
EXIT
SAVE ALL
6.3 SHUTTER/AGC menu
Selects 1 out of 7 languages.
Sets ON/OFF for enabling/disabling of ID display.
Factory default ID is Software version of camera.
User programmed camera ID will be lost and restored with Factory default
ID by CAMERA RESET. See '6.12 ID menu' for editing ID.
Restores FACTORY DEFAULT.
To save the restored parameters, move cursor to 'SAVE ALL' and press ● button before exiting the setup menu.
Returns to MAIN menu-1.
Exits the setup menu.
To save the changes, move cursor to 'SAVE ALL' and press ● button before exiting the setup menu
Saves all settings by pressing ● button when cursor is on 'SAVEALL'
This menu explains how to control/select SHUTTER, AUTO IRIS and AGC to get the best image for high luminance and the low luminance according to the scene.
For example, to reduce the ‘wash out’ and extend the dynamic range for highlighted scene, you will use
SHUTTER+AUTO IRIS in outdoor daylight. This mode may show color rolling or video level hunting problems in certain lighting condition such as fluorescent lights.
For Flickerless mode which reduces flickers by NTSC cameras under 50Hz light or PAL camera under
60Hz light, MAIN>SHUTTER/AGC>MANUAL>SHUTTER must be set to 1/100 (NTSC), 1/120 (PAL) and
MAIN>SHUTTER/AGC>AUTO>MODE to AUTO IRIS. Normal shutter speed with an auto iris lens should be set to 1/60 (NTSC) and 1/50 (PAL) for the best sensitivity.
This is a complicated menu so please proceed with care when handling the Shutter.
To enter SHUTTER/AGC menu, press ● button at MAIN menu-1>SHUTTER/AGC.
7
6.3.1 SHUTTER/AGC>AUTO SETUP menu
AUTO SETUP
MODE
BRIGHT-
NESS
Default
AUTO
IRIS
032
Descriptions
Sets the shutter mode from AUTO IRIS or SHUT+AUTO IRIS when
MAIN>LENS>AUTO menu, but it is fixed to SHUT if in the
MAIN>LENS>MANUAL menu.
AUTO IRIS - Light level is controlled by an auto iris lens only.
For proper auto iris operation, the auto iris operation mode in MAIN>
LENS>AUTO>MODE must be set to AUTO.
The shutter speed is fixed to the setting at MAIN>SHUTTER/AGC>
MANUAL> SHUTTER.
Set SHUTTER to 1/60 (NTSC) or 1/50 (PAL) for the best sensitivity
unless it is in Flickerless mode.
To set Flickerless mode, MAIN>SHUTTER/AGC>MANUAL>SHUTTER
must be set to 1/100 (NTSC), 1/120 (PAL) and MAIN>SHUTTER/AGC>
AUTO>MODE to AUTO IRIS.
SHUT+AUTO IRIS- Light level is controlled by the combination of an
auto iris lens and a shutter control to improve the highlight from wash-
out and extend the dynamic range. Shutter speed can vary between
1/60 (1/50) ~ 1/10,000sec.
This mode enhances the overall video quality of daylight but may show more smear over a bright spot light or may show color rolling or video level hunting under certain lighting conditions such as fluorescent lights.
Adjusts the brightness of the image with an auto iris lens or a shutter speed control + an auto iris lens.
MODE AGC Sets AGC to compensate the video level when the scene is dim.
BRIGHT-
NESS x0.50
Sets the brightness level which starts AGC from x0.25, x0.50, x0.75 and x1.0 of full video level.
If set to x0.50, the camera will start AGC when the video level goes down below the 50% level.
NOTICE: The setting AUTO IRIS at SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE MODE will be
changed to SHUT+AUTO IRIS if MAIN menu-1>LENS is changed to MANUAL.
As a result of this, the lens iris can NOT be fully opened when MAIN menu-1>LENS>
AUTO IRIS> MODE is OPEN.
This can be recovered by setting SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE MODE
to AUTO IRIS.
8
6.3.2 SHUTTER/AGC>MANUAL SETUP menu
MANUAL
SETUP
Default
MODE
SHUT
+AGC
Descriptions
Compensates the video level by the manual shutter control and AGC.
SHUTTER
1/60
(1/50)
Sets the manual shutter to 1/60(1/50), 1/100(1/120), 1/250,1/500,1/1000,
1/2000, 1/4000 or 1/10000.
Manual shutter is only useful when luminance is unchanged.
AGC 6.00
Sets AGC gain in dB. Higher gain compensates brighter but noise increases.
Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44.8dB.
6.4 LENS menu
To enter LENS menu, press ● button at MAIN menu-1>LENS>AUTO.
AUTO IRIS
TYPE
MODE
SPEED
Default
DC
AUTO
080
MUST BE SET TO DC ONLY.
This camera does NOT support video type auto iris lens.
AUTO – Lens iris is automatically controlled according to the scene’s light level.
OPEN – Lens is fully opened regardless of the light level.
CLOSE – Lens is fully closed.
Descriptions
Adjusts the iris control speed.
The lower the value, the faster the speed.
If the speed is too slow or fast, the iris control may be unstable.
9
6.5 DAY/NIGHT menu
To enter DAY/NIGHT menu, press ● button at MAIN menu-1>DAY/NIGHT.
IMPORTANT ACTIVITY!!!
DAY->NIGHT and NIGHT->DAY operations m ust be exam ined and verified at the final installation.
Block the lens for a few seconds for NIGHT mode then release and let it return to DAY mode.
If camera stays at NIGHT mode for more than 10sec, slightly decrease NIGHT→DAY THRES and repeat the fore-mentioned steps.
If the scene is too dim or lens iris was adjusted too low (near close), it may not return to DAY.
DAY/NIGHT Default
IR
OPTIMIZER
OFF
Descriptions
IR OPTIMIZER feature can reduce the over-saturation in video caused by the
narrow emitting IR LEDs
OFF – Disables IR OPTMIZER.
ON – Enables IR OPTIMIZER.
MODE AUTO
There are two modes available by how to manage IR OPTIMIZER.
AUTO – Reducing the over-saturation is automatically adjusted along with the
location of the subject.
CENTE R – Center area is prioritized to reduce the over-saturation.
Over-saturation in the side area could be ignored.
LEVEL 015
Overall brightness is adjusted when IR OPTIMIZER is working.
High value in LEVEL increases the brightness but the over-saturation could occur.
Low value in LEVEL decreases the brightness and the dim area could be darker.
10
6.6 PICT ADJUST menu
To enter PICT ADJUST menu, press ● button at MAIN menu-1>PICT ADJUST.
PICT ADJUST Default
MIRROR
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
GAIN
OFF
000
120
128
128
128
Descriptions
Picture will be flipped horizontally if it turns ON.
Increases or decreases the brightness of the picture.
This is different from that of DC iris lens and simply increases or decreases the digital gain of video.
Do not increase this too much, or the dynamic range for the highlight area will decrease.
Increases or decreases the contrast of the picture.
Increases or decreases the sharpness of the picture.
Too much sharpness can make the image appear harsh and will show more noise. It may also show line flicker at the edge of object in the picture.
Adjusts hue for NTSC version only
Increases or decreases the color gain of the picture
11
6.7 WHITE BAL menu
White balance can be set to ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK.
ATW (Auto Tracking White balance) and PUSH (Full pull-in) is continuously monitoring/analyzing the color
temperature of the incoming light and correcting the white balance.
ATW limits the color temperature range to about 2,500˚K~8,500˚K to reduce the excessive compensation
for a large object that has a single color.
PUSH has no limits between about 1,800˚K~10,500˚K, but it may over-compensate the white balance for
a large object that has a single color.
In cases under 2,500˚K such as halogen light, ATW may stop and if so, PUSH mode is recommended.
USER1 and USER2 are a fixed white balance which is user-programmable by R-GAIN and B-GAIN and
useful only for consistent/steady lighting.
ANTI CR (Anti Color Rolling) can reduce color rolling under fluorescent lighting when the camera
operates in shutter control mode without an auto iris lens. (NTSC version only).
MANUAL white balance is a kind of fixed white balance that is user-programmable by B-GAIN, (R-GAIN
will be automatically adjusted in accordance with B-GAIN) and useful only with consistent/steady lighting.
PUSH LOCK is a fixed white balance where the white balance is compensated only while ● button is
pressed at MAIN>WHITE BAL>PUSH LOCK and finishes the white balance when ● button is released.
To enter ATW (MANUAL) menu, press ● button at MAIN menu-1>WHITE BAL>ATW(MANUAL).
ATW
SPEED
DELAY CNT
ATW FRAME
ENVIRON-
MENT
Default
250
001
X2.00
INDOOR color temperature.
Descriptions
Sets the AWB compensating speed. Lower value makes AWB faster.
CAUTION If AWB is too fast, it may produce color oscillation.
Adjusts the AWB compensation period to next update of AWB.
The smaller value will update AWB more frequently.
A higher value than x1.00 will extend the ATW range at lower and higher
Selects INDOOR or OUTDOOR.
The ATW is optimized for limited applications.
INDOOR - Optimized for Indoor installation and it compensates ATW for low color temperature such as incandescent lights.
OUTDOOR - Optimized for outdoor sunlit applications and compensates
ATW for high color temperature such as daylight.
Determines the ATW range with respect to the fundamental range.
12
MANUAL WB
LEVEL
Default
064
Descriptions
Adjusts the manual white balance by LEVEL, (B-GAIN).
6.8 ATR (Adaptive Tone Reproduction) Menu
The ATR feature improves the dynamic range and the visibility of the image by providing the optimal gradation compensation of the image in one field. This is achieved by two ways of image processing, luminance compression and contrast enhancement, so that the tone can be enhanced in highlighted and dark areas.
To enter ATR menu, press ● button at MAIN menu-1>ATR.
ATR
LUMINANCE
CONTRAST
Default
MID
MID the entire image can converge toward the medium level.
LOW will compensate minimally and HIGH will be averaging the image more. With a HIGH setting, the image may look less contrastive and noise may increase in the dark area.
Adjusts the strength of the image contrast.
If set to too high, the dark area may lose detail and the high luminance area may saturate.
Descriptions
Compresses the highlighted areas and enhances the dark areas so that
13
6.9 BACKLIGHT menu
To enter BACKLIGHT menu, press ● button in MAIN menu-1>BACKLIGHT.
The Backlight Compensation – BLC – function is used to brighten an image in the foreground with a highly lit area behind it such as sunlight, limiting the affect of silhouetting.
BLC OFF BLC ON
The Highlight Compensation – HLC – function is used to black out highlighted areas that may blind the camera, in order to enable a clear visual image of objects, such as the license plates of an oncoming vehicle or other objects that may be obstructed by headlamps.
HLC OFF
6.10 NR menu
To enter NR menu, press ● button at MAIN menu-2>NR.
HLC ON
14
NR
NR MODE
Y LEVEL
C LEVEL
Default
Y/C
006
004
6.11 MOTION DET menu
Indicates the noise reduction strength for the luminance signal.
A higher value performs a stronger noise reduction, which makes the image less sharp.
Indicates the noise reduction strength for the chrominance signal.
A higher value performs a stronger noise reduction and makes the image less sharp.
Descriptions
Selects OFF, Y, C or Y/C, which noise reduction is performed with.
Up to 4 motion detection areas are available and each area is programmable in size and location.
The motion is displayed by means of blocks when MAIN menu-2>MOTION DET and MOTION
DET>BLOCK DISP are ON.
To enter MOTION DET menu, press ● button at MAIN menu-2>MOTION DET>ON.
MOTION DET
DETECT
SENSE
BLOCK DISP
MONITOR
AREA
AREA SEL
Default
080
ON
OFF
1/4
Descriptions
Adjusts the sensitivity for detecting motion. Higher value is more sensitive.
Enables or disables display blocks for the area where motion is detected.
Displays four motion windows as programmed in sizes and positions.
Selects one of AREA1~AREA4 to be adjusted.
TOP (BOTTOM) -
(bottom) border of the selected window at AREA SEL.
LEFT (RIGHT) -
◀
button moves up and
►
button moves down the top
◀
button moves left and
►
button moves right the left
(right) border of the selected window at AREA SEL
15
6.12 PRIVACY menu
Up to 8 privacy areas are available and each area is programmable in size and location.
The number of privacy areas is limited to four when MOTION DET>MONITOR AREA is ON.
The privacy areas are masked with the color selected in PRIVACY>COLOR.
To enter PRIVACY menu, press ● button at MAIN menu-2>PRIVACY>ON.
PRIVACY
AREA SEL
COLOR
TRANSP
MOSAIC
Default
1/8
1
1.00
OFF
TOP (BOTTOM) - top (bottom) border of the selected window at AREA SEL.
LEFT (RIGHT) -
◀
button moves up and
►
button moves down on the
◀
button moves left and
►
button moves right on the left
(right) border of the selected window at AREA SEL.
0.00 - Mask is fully transparent and not visible.
0.50 - Mask is 50% transparent.
0.75 - Mask is 25% transparent.
1.00 - Mask is not transparent.
AREA SEL.
Descriptions
Selects one of AREA1~AREA8 to be adjusted.
Sets one of 8 colors for the selected mask window at AREA SEL.
Transparency rate for the mask can be adjusted.
Enables or disables the mosaic effect for the selected mask window at
6.13 LANGUAGE menu
Seven languages, ENGLISH, JAPANESE, DEUTCH (German), FRANCAIS (French), RUSSIAN,
PORTUGUES (Portuguese) and ESPANOL (Spanish), are available with this camera.
16
6.14 CAMERA ID menu
Up to 40 characters can be input for camera ID.
To enter CAMERA ID menu, press ● button at MAIN menu-2>CAMERA ID.
CAMERA ID input line
COMMAND LINE
Use ▲ ,
▼
,
◀
,
►
buttons to move a block cursor in the character table and press ● button to input the selected character.
To move the character input position on CAMERA ID input line, move a cursor to ←→ on COMMAND LINE and press ● button on ← or →.
To clear CAMERA ID input line, move a cursor to CLR on COMMAND LINE and press ● button.
To set the location of CAM TITLE to be displayed on the monitor, move a cursor to POS and press ● button and then menu disappears and CAMERA ID will be displayed on the monitor.
Move CAMERA ID by using ▲ ,
▼
,
◀
,
►
buttons and press ● button to fix.
Menu will appear again.
To finish CAM TITLE menu, press ● button on RET on command line.
6.15 CAMERA RESET
Camera loads Factory defaults.
To save them, go to SAVE ALL and press ● button.
6.16 EXIT
Exits SETUP MENU and returns to the normal display
17
7
. Specifications
VTC-IRE70/650
Image Device
Resolution
Minimum illumination
Effective Pixels
S/N Ratio
Electronic Iris
Infrared LEDs
IR Distance
Day/Night
Built-In Lens
Iris Mode
White Balance
Gain Control
Flicker Reduction
Video Output
TV System
Scan Frequency
Synchronization
Light Compensation
Noise Reduction
E-WDR
Motion Detection
Privacy Mask
OSD Language
Water Resistance
Construction
Power Source
Power Consumption (12VDC)
Power Consumption (24VAC)
Operating Conditions
Length (Ceiling Mounted)
Length (Wall Mounted)
Width (Camera)
Width (Camera w/Sun Shield)
Height
1/3” High Density Sony EX-VIEW CCD & Effio-E DSP (960H)
700 TV lines
0.003Lux / F1.2 (0 Lux with IR LEDs ON)
976(H) x 494(V)
More than 50dB with AGC OFF at 50IRE
1/60 to 1/100,000 sec.
70 850nm IR LEDs
Over 300 Feet
True Day/Night by ICR
6-50mm DC A/I, Switched IR Cut Filter D/N Lens
DC Drive Iris Control (Internally Fixed)
1,800~10,500ºK Automatic Tracking
Auto
Yes
VBS 1Vpp +/- 10%, 75ohm
2:1 Interlace
59.94Hz(V), 15.734Khz(V)
Internal/Line Lock (Default: Internal)
HLC (Highlight Compensation) / BLC (Backlight Compensation)
2DNR
YES by ATR (Adaptive Tone Reproduction)
YES (24 x 16 Grid)
Up to 8 Programmable Mask Areas
English, Japanese, German, French, Russian, Portuguese, Spanish
IP68
Aluminum Housing
12VDC/24VAC (Dual Voltage)
110mA / 800mA (IR OFF/ON)
120mA / 820mA (IR OFF/ON)
-4ºF~+122ºF (-20ºC~+50ºC) / 85% RH Max
N/A
11.25" (286mm)
3.6" (91mm)
4.7" (119mm)
8.5" (216mm)
Weight 4.4 lbs. (1996g)
● Design and specifications are subject to change for product improvements without prior notice.
18
8. Dimensional Drawings
214mm / 8.4in
172mm
6.8in
280.2mm / 11.03in
228.5mm
9in
72.1mm / 2.8in
58mm 2.3in
58mm
2.3in
72.1mm
2.8in
19
100mm
3.93in
THE MIGHTY DOME
THE ULTRA VERsATILE DOME CAMERA sERIEs
The Mighty Series Dome cameras include models produced with the new Pixim-Powered Seawolf Wide Dynamic Range
DSP and the Sony Effio Day Night DSP. The Highest resolution Analog camera line up to date offers 700 TV Lines of Resolution, up the coax OSD Control and low light capability up to 0.00008 lux. Created to meet and solve the challenges brought on by varying lighting conditions and display clear, crisp images more accurately than ever before.
A long list of mounting and configuration options are also available for this camera including extreme low temperature
Heater and built in UTP.
Mighty Domes Conventional Cameras
Mighty Domes Conventional Cameras
UTP Interface, Standard
Heater/Blower kits available for all weather protection all the way down to -60*F!
FEATURES:
• High Resolution of 700 TVL incorporating Pixim Seawolf
DSP for WDR & Sony Effio for Day/Night.
• Ultra Versatile Design with Infinity Ball Mount for
Any Viewing Angle
• OSD (On Screen Display) with Joystick control for
Camera Function Setup
• Secondary Video Output (Cable Included)
• True Mechanical Day/Night function available
Mighty Dome Inside
(Shown in Black)
• Options include 24VAC with Heater/Blower (down
-60°F) & UTP Transmission options.
• Vandal Resistant Version is Fully Gasket Sealed with an IP686 Water tight NEMA Rating
•
• 1” Conduit Knockout
Semi-Flush or Surface Mountable
• EXTENSIVE mounting options available
• With Night Watch DSS Low Light Color
Technology
• IR Corrected Lens Options Lens options: 2.9-10mm,
9-22mm, and 18-50mm
• 24VAC/12VDC Dual Voltage Operation
• Available in Ivory or Black
OSD Joystick Controls to
Fully Gasket Sealed IP68
Rated Weatherproof
Design. (Outdoor Vandal
Version Only)
Can be Surface Mounted with Included Surface
Mount Casing or Semi-
Flush Mounted for Sleek,
Low Profile Installation.
Secondary Video
Output Enables Ease of Adjustment after
Installation.
Friction Fit Ball Mount
Camera Module Can
Achieve Virtually Any
Viewing Angle.
The Mighty Dome Vandal base has been designed to manage and protect video and power cables without the need for external adaptors.
VT-EHP
8 & 16 Channel Digital Video Recorders
The highest recorded resolution in a Real Time Analog
DVR, the EHP delivers “D1” – 704 x 480 @ 480pps maximum frames per second. All of the powerful features and applications of the EH Family can be found in the EHP plus a built in DVD/RW, Jog Shuttle for ease of playback,
Individual video loop through, individual alarm inputs & outputs as well as Point-of-Sale (POS) integration and search functions. Available configurations of 8 and 16 channels with a maximum 8 Terabytes internal storage and
HDD Mirror redundancy place this DVR at the pinnacle of the VITEK EH Lineup.
Video Input
IPS (Display / Recording)
Video Output
BNC Output
Audio In/Out
Storage
Archive
USB Port
System Control
Network
RJ-45 Ethernet Port
Playback Rate
PTZ
Point of Sale (POS)
Motion Area Setting
Recording Resolution Setting
Recording Quality Control
Player
E-mail notification
System Configuration
Bandwidth limit
Two-Way Audio
Case Form Factor
FEATURES:
• 8 or 16 Video Inputs with Main, 4 Spot, and 1080P HDMI outputs
• H.264 Compression
• 4 Alarm Inputs / 1 Relay Out
• Up to 480fps Live Display & 480fps Recording (VT-EHP16) /
240/240 (VT-EHP8)
• Built-in Point-of-Sales support
• Built-in Data Redundancy
• Remote Viewing over a LAN or Internet
• Free Applications for iPhone, iPad, iTouch and Droid Devices
• 500GB to 8TB Internal Storage Options (up to 8TB @ 4x2TB)
• Email Event Notification with Snapshot
• CMS Central Management Software (Included)
• MAC Client Software (Included)
• Control locally via Front Panel, USB Mouse or with the Included IR
Remote control
• PTZ Control over RS-485
VT-EHP8 VT-EHP16
8 Channels
240 / 240
16 Channels
480 / 480
HDMI - 1 1080P (1920 x 1080) / VGA - 1 SXGA (1280 X1024)
Monitor: 1 Composite (BNC) / Spot: 4 Composite (BNC)
4 Line In (RCA) / 1 Line Out (RCA), CODEC : G.711 (64Kbps)
Up to 4 Internal HDD (SATA) / Internal DVD-RW / E-SATA
CD/DVD-RW / USB Device / Network
2 Front + 1 Rear
Front Panel, USB Mouse, Joystick Controller, Included IR Remote Control
TCP/IP, HTTP, DHCP (DDNS)
10M/100M/1Gbps
240 fps @ 704x480 480 fps @ 704x480
2 - RS-485 - Supports most of PTZ protocols with up to 255 Presets
YES
Adjustable Grid (16 x 12)
By each camera for different resolution setting(CIF/2CIF/D1)
4 Levels (Low/Standard/High/Highest)
Backup player, Window Media Player and HDD PC Viewer
E-mails to specific users to notify events
Full setup configuration over network
YES: Adjustable by User
YES
2U
Remote Viewing Apps for iPhone, iPad
& Android
Included VT-EH CMS Software allows remote viewing and control of multiple
VT-EH Series DVR’s even when located at multiple locations!
VT-EHP8 Rear Connections VT-EHP16 Rear Connections
Remote Viewing from anywhere using
Internet Explorer
VITEK LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is non-transferable and extends only to the original buyer or end user customer of a Vitek Authorized Reseller.
The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.
The product must not have been tampered with in any way or the guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized
Reseller.
28492 Constellation Road ValenCia, Ca 91355
WWW.ViteKCCtV.CoM | 888-ViteK-70
VeRsion 2
09/2012
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project