Yamaha DPX-1 Owner`s manual

01EN_DPX-830_EX-cv_new.fm Page 1 Monday, December 26, 2005 8:21 PM
DPX-830
DPX-830
© 2006
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
Printed in Japan
871D460A20
Digital Cinema Projector
Projecteur Cineme Numerique
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
IMPORTANT SAFETY INSTRUCTIONS
7
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
8
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
9
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
10
11
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
12
For Canadian customers
13
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian ICES003.
14
15
IMPORTANT!
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the bottom of the unit.
Retain this Owner’s Manual in a safe place for future reference.
Please read all these instructions regarding your projector and retain
them for future reference. Follow all warnings and instructions
marked on the projector.
1
2
3
4
5
6
i
Read instructions: All the safety and operating instructions
should be read before the appliance is operated.
Retain instructions: The safety and operating instructions
should be retained for future reference.
Warnings: All warnings on the appliance and in the operating
instructions should be adhered to.
Instructions: All operating instructions must be followed.
Cleaning: Unplug this projector from the wall outlet before
cleaning it. Do not use liquid aerosol cleaners.
Attachments and equipment: Never add any attachments
and/or equipment without the approval of the manufacturer as
such additions may result in the risk of fire, electric shock or
other personal injury.
16
17
18
Water and moisture: Do not use this projector near water or
in contact with water.
Accessories: Do not place this projector on
an unstable cart, stand, tripod, bracket or
table. Use only with a cart, stand, tripod
bracket, or table recommended by the
manufacturer or sold with the projector. Any
mounting of the appliance should follow the
manufacturer's instructions and should use a
mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with care.
Quick stops, excessive force and uneven surfaces may cause the
appliance and cart combination to overturn.
Ventilation: Slots and openings in the cabinet are provided for
ventilation, ensuring reliable operation of the projector and to
protect it from overheating. Do not block these openings or
allow them to be blocked by placing the projector on a bed,
sofa, rug, or bookcase. Ensure that there is adequate ventilation
and that the manufacturer's instructions have been adhered to.
Power sources: This projector should be operated only from
the type of power source indicated on the marking label. If you
are not sure of the type of power, please consult your appliance
dealer or local power company.
Power-cable protection: Power-supply cables should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them. Pay particular attention to
cords at plugs, convenience receptacles, and points where they
exit from the appliance.
Overloading: Do not overload wall outlets and extension
cords as this can result in a fire or electric shock.
Objects and liquids: Never push objects of any kind through
openings of this projector as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the projector.
Servicing: Do not attempt to service this projector yourself.
Refer all servicing to qualified service personnel.
Damage requiring service: Unplug this projector from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
(a) If the power-supply cable or plug is damaged.
(b)If liquid has been spilled, or objects have fallen into the
projector.
(c) If the projector does not operate normally after you follow
the operating instructions. Adjust only those controls that are
covered by the operating instructions. An improper
adjustment of other controls may result in damage and may
often require extensive work by a qualified technician to
restore the projector to its normal operation.
(d)If the projector has been exposed to rain or water.
(e) If the projector has been dropped or the cabinet has been
damaged.
(f) If the projector exhibits a distinct change in performance this indicates a need for service.
Replacement parts: When replacement parts are required,
be sure that the service technician has used replacement parts
specified by the manufacturer or parts having the same
characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
Safety check: Upon completion of any service or repair to
this projector, ask the service technician to perform safety
checks determining that the projector is in a safe operating
condition.
Connection cable: Use the supplied RS-232C and RGB
cables with this equipment to keep interference within the limits
of an FCC/EN55022 Class B device.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party:
Address:
Yamaha Electronics Corporation
6660 Orangethorpe Avenue
Buena Park, CA90620
Telephone:
Fax:
714-522-9105
714-670-0108
Type of Equipment:
Projector
Model Name:
DPX-830
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See the owner’s manual instructions if interference to radio reception is suspected.
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void
your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow
all installation instructions. Failure to follow instructions
could void your FCC authorization to use this product in the
USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will not
result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the operation of
other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is
found to be the source of interference, which can be determined
by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please
contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
ii
Caution: Read this before operating this unit.
Warning
Place of installation
•
This unit must be grounded
•
Do not use this projector in a computer room
This projector is not for use in a computer room as defined in
the Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANIS/NFPA 75.
For safety reasons, refrain from setting the projector at any place
subjected to high temperature and high humidity. Maintain an
operating temperature, humidity and setting as specified below:
•
Unplug immediately if there is something wrong with
your projector
Do not operate if smoke, strange noise or odor comes out of
the projector. It might cause fire or electric shock. If this
happens, unplug immediately and contact your dealer.
•
Never remove the cabinet
This projector contains high voltage circuitry. An inadvertent
contact may result in an electric shock. Except as specifically
explained in the owner's manual, do not attempt to service
this product yourself. Contact your dealer when you want to
fix, adjust or inspect the projector.
•
Operating temperature: between 41°F (5°C) and 95°F (35°C).
•
Operating humidity: between 30% and 90%
•
Never put any heat-producing device under the projector. The
projector may overheat.
•
Do not install the projector near any equipment that produces a
strong magnetic field. Also refrain from installing near the
projector any cable carrying a large current.
•
Do not install the projector in a place that is unstable or subject
to vibration; otherwise, it may fall and cause serious injury
and/or damage to the unit.
•
Do not stand the projector on its side; otherwise, it may fall and
cause serious injury and/or damage to the unit.
•
Do not modify this projector
It can lead to fire or electric shock.
•
Do not tilt the projector more than 10° right/left or 15°
forward/backward; otherwise, it may cause a lamp explosion.
•
Do not continue using this projector if you drop or
break it
Unplug the projector and contact your dealer for inspection.
It may lead to fire if you continue using it.
•
Do not place the projector near an air conditioning unit or heater
to avoid hot air to the vents of the projector.
•
Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
•
Do not face the projector lens towards the sun
It can lead to fire.
•
Use correct voltage
If you use incorrect voltage, it can lead to fire.
•
Do not place the projector on uneven or unstable
surfaces
Place the projector on a leveled and stable surface only.
•
Do not look into the lens when it is operating
It may cause serious eye injury.
•
Do not turn off the main power abruptly or unplug the
projector during operation
It can lead to lamp breakage, fire, electric shock or other
trouble. Always wait for the fan to turn off before turning the
main power off.
•
Avoid all contact with the air exhaust vents and
bottom plate
The air exhaust vents and bottom plate heat up during
operation and may cause personal injury or damage to other
equipment. Do not touch them, place other equipment in front
of the air exhaust vents, or set the projector on a desk which is
easily affected by heat.
•
Do not look into the air exhaust vent when the
projector is operating
Heat, dust, etc. may blow out of it and cause injury to your
eyes.
•
Do not block the air intake and exhaust vents
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality and/or
fire.
This unit is not disconnected from the AC power source as long
as it is connected to the wall outlet, even if this unit itself is
turned off. This state is called the standby mode. In this state,
this unit is designed to consume a very small quantity of power.
iii
– Other components, as they may cause damage and/or discoloration on
the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage to this
unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid may cause
electrical shock to the user and/or damage to this unit.
European compliance notice
This video projector complies with the requirements of the EC
Directive 89/336/EEC “EMC Directive” as amended by Directive
92/31/EEC and 93/68/EEC, and 73/23/EEC “Low Voltage
Directive” as amended by Directive 93/68/EEC.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3-pin plug fitted. For details, refer to the instructions
described below.
Note
•
The plug severed from the mains lead must be destroyed, as a plug
with a bared flexible cord is hazardous if engaged in a live socket
outlet.
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN-AND-YELLOW:
EARTH
BLUE:
NEUTRAL
BROWN:
LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be
connected to the terminal in the plug which is marked by the
letter “E” or the safety earth symbol or coloured GREEN or
GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the
terminal marked with the letter “N” or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal marked with the letter “L” or coloured RED.
Table of contents
1 Getting started
2
Inappropriate places for installation .....................2
Accessory check ..................................................3
Inserting the batteries into the remote control......4
2 Controls and functions
5
Projector overview ...............................................5
Remote control overview .....................................6
Using the picture quality adjusting buttons .....6
3 Using the remote control
7
Operational range ................................................7
Reception angle ...................................................7
4 Installation
8
Setting up the screen ...........................................8
Mounting the projector on the table .....................8
Adjusting the projection angle ..............................8
Mounting the projector on the ceiling ...................9
Screen size and projection distance ..................10
5 Connections
11
Basic home theater system connection .............11
Connecting to a video player, etc.......................12
Connecting to a DVD player or
HDTV decoder ...................................................12
HDMI or DVI connections ..................................13
D-SUB connections............................................13
Connecting to a computer ..................................14
TRIGGER terminal .............................................15
Plugging in the power cable ...............................15
6 Projection
8 Adjusting video images
27
Selecting the gamma mode (GAMMA) ............. 27
Customizing the gamma mode (GAMMA) ........ 27
Adjusting brightness (CONTRAST and
BRIGHTNESS).................................................. 27
CONTRAST ................................................. 27
BRIGHTNESS.............................................. 27
Selecting the color temperature
(COLOR TEMP.) ............................................... 28
Customizing the color temperature
(COLOR TEMP.) ............................................... 28
About color temperature .............................. 28
Adjusting color (SATURATION and HUE) ........ 29
SATURATION .............................................. 29
HUE ............................................................. 29
Sharpening or softening images
(SHARPNESS).................................................. 29
LPF (Progressive filter) ..................................... 29
9 MEMORY function
30
Saving memory settings.................................... 30
10 Adjusting computer images
31
Adjusting computer images............................... 31
Simple method to adjust the image
position......................................................... 31
11 Replacing the lamp
32
Interval of lamp replacement............................. 32
Replacing the lamp ........................................... 33
Maintenance...................................................... 33
16
12 Attaching a lens filter and cap 34
Viewing video images ........................................16
KEYSTONE adjustment................................17
IRIS button ....................................................17
Examples of the aspect ratio.........................18
Setting the aspect ratio .................................18
Viewing computer images ..................................19
AUTO / AUTO SYNC buttons .......................20
Connecting to a notebook computer .............20
Attaching a commercially available lens filter.... 34
Attaching the lens cap....................................... 34
7 Menu
21
Menu overview ...................................................21
How to set the menus ...................................22
Menu settings.....................................................23
13 Troubleshooting
35
Troubleshooting ................................................ 35
14 Indicators
38
Normal conditions ............................................. 38
Abnormal conditions.......................................... 38
15 Specifications
39
Projector specifications ..................................... 39
Dimension drawings.......................................... 41
1
1 Getting started
◆ Inappropriate places for installation
If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place to
install this unit by avoiding the places listed below.
1. Places where the temperature and humidity vary greatly
• Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely
low.
• This unit must be used within a temperature range of 41°F (5°C) to 95°F (35°C).
• This unit must be used within a humidity range of 30% to 90%
2. Places without adequate ventilation
•
•
•
•
•
•
Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.
Do not cover the ventilation slots of this unit. Covering the slots will obstruct heat dissipation.
Install this unit on the firm surface.
Do not cover this unit with a tablecloth, etc.
Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.
If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.
3. Places where it gets dusty
• If the filter is blocked with dust, the temperature of this unit may become too high.
4. Places with too much vibration or impact
• Vibration and impact can damage parts of this unit.
5. Places where this unit gets exposed to water or high humidity
• If this unit is exposed to water of high humidity, it may cause a fire or electrical shock.
6. Unstable places
• If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.
7. In close proximity to a radio or stereo
• The unit may interfere with reception if placed in close proximity to a radio or television receiver.
8. Uneven surfaces
• Slanting the projector more than 10° right and left or 15° front and rear may cause problems (such as the lamp exploding).
Warning
• To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.
*DLPTM, DMDTM, DarkChip2TM, and DarkChip3TM are registered
trademarks of the Texas Instruments corporation of America.
* HDMI, the HDMI logo and High-Definition Multimedia Interface
are trademarks or registered trademark of HDMI Licensing LLC.
2
◆ Accessory check
The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.
■ Cables
■ Power supply parts
mini D-SUB
15-pin
(For US)
D-SUB 9-pin
8-pin
mini D-SUB
15-pin
(For Europe)
RGB cable for PC
(WF76940)
RS-232C cable
(WF76930)
Power cable
• Used for adjustment by service person.
■ Remote control parts
■ Others
ON
W
TO
PO
AU
ER
A
RM
SP
NO
ST
AN
T
PE
EC
AS
AL
DB
CT
SQ
MI
Y
HD
UE
E
CO
UB
HID
EZ
D-S
S.
.
IN
MP
T
OM
PU
ZO
DPX-830
VID
EO
Digital Cinema Projector
Projecteur Cineme Numerique
S-V
O
R
IDE
TE
NU
EN
ME
1
M
.
O
NT
EM
CO
Y
2
R
YS
IG
TN
A
BR
MM
KE
GA
HT
3
SH
G
P
IN
EM
TT
P
C.T
AR
SE
IR
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
IS
R
D
P-8
1
Remote control
R03 (Size-AAA) battery (two)
Lens cap
Owner’s manual
Important
• The supplied power cables are to be used exclusively for this product. Never use them for other products.
• The power cables for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.
• The provided power cable for the U.S. is rated at 120 V. Never connect this cable to any outlet or power supply using other
voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power
cable separately.
3
◆ Inserting the batteries into the remote control
1
3
2
1. Remove the rear lid of the remote control.
2. Check the polarity markings (+, –) of the batteries, and set
them correctly, inserting their (–) side first.
• If the battery is inserted from the (+) side first, inserting the (–)
side becomes difficult because the coil spring end hits on the
battery side. If the battery is forced to insert in this way, the
outer label of the battery may get ripped and cause a shortcircuit and heating.
3. Attach the rear lid.
Important
• Use two size-AAA batteries (R03).
• Replace the two batteries with new ones when the remote
control is slow to operate.
Caution
•
•
•
•
•
•
•
•
•
•
4
Using the wrong type of battery may cause an explosion.
Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
Dispose of used batteries according to your local regulations.
Batteries may explode if misused. Do not recharge, disassemble, or dispose of in fire.
Be sure to handle the battery according to the instructions.
Load the battery with its positive (+) and negative (–) sides correctly oriented as indicated on the remote control.
Keep batteries out of reach of children and pets.
Remove the batteries, if the remote control is not used for a long time.
Do not combine a new battery with an old one.
If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with
your eyes, rinse them with water and then consult your doctor.
2 Controls and functions
◆ Projector overview
1
Top view
Bottom
view
3
2
8
12
9
10
11
10
11
4
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
5
Side view
6
7
FOCUS ring
ZOOM ring
Control panel
Air intake vent
Remote control sensor (Front)
Air intake vent
Air exhaust vent
Adjustment foot (Front)
Lamp cover (see page 33)
Adjustment feet (Rear)
Foot adjustment buttons (Left/Right)
Air intake vent
Control panel
1. STANDBY/ON,
2. AUTO SYNC,
5
1
6
AUTO SYNC
2
7
3
8
3.
4.
5.
6.
7.
button
button
D-SUB/HDMI,
button
MENU button
STATUS indicator
POWER indicator
KEYSTONE, ENTER button
8. VIDEO/S/COMP.,
9.
button
button
Important
9
MENU
• While the menu is on the screen, the KEYSTONE button
functions as the ENTER button and the D-SUB/HDMI,
VIDEO/S/COMP., and AUTO SYNC buttons function as
the , , and
buttons respectively.
4
DIGITAL CINEMA PROJECTOR DPX-830
Rear panel
1
2
3
4
5
COMPONENT
AC IN
Y
HDMI
SERIAL
PB/CB
PR/CR
D-SUB
S-VIDEO
USB
TRIGGER
1.
2.
3.
4.
5.
6.
7.
VIDEO
8.
6
7 8
9 10
11
9.
10.
11.
AC IN
HDMI input terminal
D-SUB input terminal
Remote control sensor (Rear)
COMPONENT input terminals
Air exhaust vent
SERIAL terminal
• Used for adjustment by service person.
USB terminal
• Used for adjustment by service person.
TRIGGER terminal
• Used for the optional electric screen.
S-VIDEO input terminal
VIDEO input terminal
5
◆ Remote control overview
1
ON
POWER
STANDBY
2
ASPECT
3
AUTO
ASPECT
HIDE
4
5
NORMAL
SQUEEZ
S. ZOOM
HDMI
COMP.
VIDEO
6
D-SUB
INPUT
7
S-VIDEO
11
12
14
16
18
13
15
17
ENTER
19
8
9
10
MENU
KEYSTN
20
MEMORY
1
2
3
CONT.
BRIGHT
C.TEMP
GAMMA
SHARP
IRIS
SETTING
1.
2.
3.
4.
5.
6.
IR signal transmitter
ON ( I ) button
AUTO button
NORMAL button
HDMI button
D-SUB button
7.
8.
9.
10.
Cursor buttons ( / / / )
MENU button
MEMORY buttons
The picture quality adjusting buttons*
* See the below for the picture quality adjusting buttons.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
STANDBY ( ) button
HIDE button
ASPECT button
S. ZOOM (Smart zoom) button
SQUEEZ (Squeeze) button
VIDEO button
COMP. (Component) button
S-VIDEO button
ENTER button
KEYSTN (Keystone) button
21. IRIS button (see page 17)
21
RDP-81
Important
• When you press a button on the remote control, the buttons
on the remote control will light up. Wait approximately 6
seconds after releasing the button for the lights to turn off.
Using the picture quality adjusting buttons
When you press either of the picture quality adjusting buttons, the message for adjusting the picture quality appears. Adjust the picture quality
by pressing the
and
buttons. The picture quality adjustment can be made alternatively in the IMAGE menu (see page 23).
CONT. (CONTRAST) ..................................... Adjusts the contrast of the projected image.
GAMMA.......................................................... Selects one of the preset gamma modes.
BRIGHT (BRIGHTNESS) .............................. Adjusts the brightness of the projected image.
SHARP (SHARPNESS) .................................. Adjusts the sharpness of the projected image.
C. TEMP (COLOR TEMPERATURE) ........... Selects one of the preset color temperatures.
6
3 Using the remote control
◆ Operational range
Front panel
Operate the remote control within a distance of 10 m from the
projector, pointing the light beam at the remote control sensor (front
or rear) of the projector.
Rear panel
AC IN
30˚
ON
30˚
30˚
POWER
STANDBY
ON
POWER
ASPECT
STANDBY
ASPECT
AUTO
ASPECT
HIDE
AUTO
ASPECT
HIDE
SQUEEZ
S. ZOOM
NORMAL
SQUEEZ
S. ZOOM
HDMI
COMP.
VIDEO
HDMI
COMP.
VIDEO
S-VIDEO
D-SUB
INPUT
INPUT
S-VIDEO
ENTER
ENTER
MENU
KEYSTN
MENU
MEMORY
1
CONT.
GAMMA
KEYSTN
MEMORY
2
3
BRIGHT
C.TEMP
CONT.
SHARP
IRIS
GAMMA
1
2
3
BRIGHT
C.TEMP
SHARP
IRIS
SETTING
SETTING
RDP-81
RDP-81
Angle to sensor
10 m
(approximate value)
30° left and right
(approximate value)
30˚
NORMAL
D-SUB
Distance to sensor
Caution
• Keep the remote control sensor out of direct sunlight or
fluorescent lamp light.
• Keep the remote control sensor at least 2 m away from
fluorescent lamps. Otherwise, the remote control may
malfunction.
• If there is an inverter-operated fluorescent lamp near the
remote control, the remote control operation may become
unstable. On this occasion, stick a commercially available
protection sticker on one of the sensors that is closer to
the fluorescent lamp.
When operating the remote control, keep the distance from the remote
control to the projector via the screen within about 5 m. The operable
range of the remote control, however, depends on the characteristics
of the screen.
STA
PO
W
BY
HID
AS
AU
ND
ER
ON
PE
AS
PE
S.
CT
SQ
TO
NO
RM
E
CT
UE
OM
VID
CO
AL
MP
EO
S-VI
.
IN
HD
ZO
EZ
PU
DE
O
T
MI
D-S
UB
EN
TE
R
KE
YS
TN
3
ME
M
NU
EM
O
RY
C.T
2
BR
1
CO
IG
GAM
MA
EM
P
IR
HT
SH
NT.
AR
IS
P
SE
TT
IN
G
RD
P-8
1
◆ Reception angle
Vertical directions
20˚
20˚
10˚
10˚
Vertical directions (ceiling mount)
20˚
20
20˚
20
7
4 Installation
◆ Setting up the screen
Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the projection angle of the projector as
shown below.
Important
• Before setting up the screen, be sure to set SCREEN ASPECT in the SETUP menu to either 16:9 or 4:3.
• Install the screen and projector so that the projector’s lens is placed at the horizontal position of the screen center.
• Do not install the screen where it is exposed to direct sunlight or lighting. Light directly reflecting on the screen makes the
projected images whitish and hard to view.
◆ Mounting the projector on the table
Determine the distance from the screen to the projector according to the size of the images to be projected (see page 10).
W
A
B
Height of the
projected image
Screen
A=B
STANDBY/ON
POWER
STATUS
AUTO SYNC
ENTER
MENU
DIGITAL CINEMA PROJECTOR DPX-830
Projected distance
• Do not place this projector on a carpet or blanket because the intake vent on the bottom surface will be blocked and the inside of the
projector will overheat, causing a breakdown or fire.
• Depending on the installation conditions, warm air that is emitted from the exhaust vents may flow into the intake vent, causing the projector
to display “Over Temperature” and then stop projecting images. If this happens, clear the area around the exhaust vent.
◆ Adjusting the projection angle
This projector is provided with three feet for adjusting the projection angle on the bottom surface. Adjust the projection angle depending on
the position of the projector.
For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the adjustment
feet on the bottom of the projector.
1. Tilt the projector upwards to the appropriate angle.
2. Press the foot adjustment buttons next to the adjustment
feet (rear), and the adjustment feet will come out.
3. Release the buttons to lock the adjustment feet (rear) to
that position.
4. Rotate the adjustment feet (rear) for fine adjustment.
• If necessary, rotate the adjustment foot (front) for fine
adjustment.
Screen
Adjustment feet (rear)
After using the projector
Put the adjustment feet (rear) back into the projector by pressing the foot adjustment buttons.
When projected images are distorted to a trapezoid
When the screen and the projector are not placed perpendicularly to each other, projected images become trapezoidal. If you cannot make the
projector and the screen perpendicular to each other by mechanical adjustments, adjust keystone (see page 17).
8
◆ Mounting the projector on the ceiling
To view images projected by the ceiling mounted projector from the front:
When the projector is installed on the ceiling, the special ceiling mount bracket, which is commercially available, is required. Be sure to ask a
certified installation specialist for installation of the projector. Contact your dealer for details.
• Yamaha assumes no responsibilities for any damage caused by use of other manufacturer’s ceiling bracket and by inadequate installation
conditions even within the warranty period.
• When installing the projector on the ceiling, set LOCATION in the SETUP menu to FRONT/CEILING.
• Ask your installation specialist to provide a breaker. When you do not use the projector, be sure to shut down the main power by the breaker.
• When the projector is installed on the ceiling, projected images may appear darker than those projected when the projector is installed on the
floor.
• Do not install the projector where the exhaust vents are exposed to air emitted by an air conditioning. Such installation may cause a
breakdown.
• Do not install the projector near a fire alarm because it emits hot air from its exhaust vents.
Optional part
Ceiling mount bracket
PMT-L71 (low ceilings)
PMT-H75 (high ceilings)
To view images projected on a translucent screen from behind:
Be sure to ask a certified installation specialist for installation of the projector. Contact your dealer for details.
• To view images projected from behind the screen, set LOCATION in the SETUP menu to REAR/TABLE.
9
◆ Screen size and projection distance
Refer to the following diagram to determine the screen size.
Hd
A
Screen size
Height of the
projected image
When the aspect ratio of the screen is 16:9
Center of the lens
B
Projected distance (L)
Width of the projected image
Diagonal
inch cm
40
102
60
152
80
203
100 254
150 381
200 508
250 635
275 699
Screen size 16:9
Height A
Width B
inch cm inch cm
20
50
35
89
29
75
52
133
39
100
70
177
49
125
87
221
74
187 131 332
98
249 174 443
123 311 218 553
135 342 240 609
Projected distance (L)
Min.
Max.
inch
m
inch
m
56
1.4
68
1.7
85
2.2
103
2.6
114
2.9
139
3.5
143
3.6
174
4.4
216
5.5
262
6.6
289
7.3
349
8.9
362
9.2
–
–
398 10.1
–
–
Hd
inch
6.6
9.9
13.2
16.5
24.7
32.9
41.2
45.3
cm
17
25
33
42
63
84
105
115
• The above figures are approximate and may be slightly different from the actual
measurements.
When the aspect ratio of the screen is 4:3
When the aspect ratio of the screen is 4:3, the positional relation between the projected image and the screen is as shown below. Refer to the
following table for installation.
Hd
A
Screen size
Height of the
projected image
When the aspect ratio of the image is 4:3
Center of the lens
B
Width of the projected image
Projected distance (L)
Diagonal
inch cm
40
102
60
152
80
203
100 254
150 381
200 508
250 635
275 699
Screen size 4:3
Height A
inch cm
24
61
36
91
48
122
60
152
90
229
120 305
150 381
165 419
Width B
inch cm
32
81
48
122
64
163
80
203
120 305
160 406
200 508
220 559
Project distance (L)
Min.
Max.
inch
m
inch
m
65
1.6
79
2.0
98
2.5
119
3.0
132
3.3
159
4.0
165
4.2
200
5.1
248
6.3
300
7.6
332
8.4
–
–
–
–
–
–
–
–
–
–
D
Hd
A
D
Height of the
projected image
C
Height of the screen
B
Center of the lens
Width of the projected image
Diagonal
inch
cm
40
102
60
152
80
203
100
254
150
381
200
508
250
635
300
762
Screen size 4:3
Height C
inch
cm
24
61
36
91
48
122
60
152
90
229
120
305
150
381
180
457
Projected distance (L)
Width B
inch
cm
32
81
48
122
64
163
80
203
120
305
160
406
200
508
240
610
Size of the projected image 16:9
Height A
Blank space (D)
inch
cm
inch
cm
18.0
46
3.0
8
27.0
69
4.5
11
36.0
91
6.0
15
45.0
114
7.5
19
67.4
171
11.3
29
89.9
228
15.0
38
112.4
286
18.8
48
134.9
343
22.6
57
• The above figures are approximate and may be slightly different from the actual measurements.
10
inch
6.8
10.2
13.6
17.0
25.5
34.0
42.5
46.8
cm
17
26
35
43
65
86
108
119
• The above figures are approximate and may be slightly different from the actual
measurements.
When the aspect ratio of the image is 16:9
Screen size
Hd
Project distance (L)
Min.
Max.
inch
m
inch
m
51
1.3
63
1.6
78
2.0
95
2.4
105
2.7
127
3.2
132
3.3
159
4.0
198
5.0
240
6.1
265
6.7
320
8.1
332
8.4
401
10.2
398
10.1
–
–
Hd
inch
6.0
9.1
12.1
15.1
22.7
30.2
37.8
45.3
cm
15
23
31
38
58
77
96
115
5 Connections
◆ Basic home theater system connection
Important
• Make sure that the power of the projector and that of the video equipment are turned off.
• Connection methods and terminal names may differ depending on the video equipment you are connnecting. Refer to the
instruction manual for the video equipment.
• Use of a long cable may affect the quality of the projected image.
PB/CB
Y
PR/CR
COMPONENT
AC IN
HDMI
SERIAL
Y
D-SUB
PB/CB
PR/CR
S-VIDEO
USB
TRIGGER
VIDEO
Video player
DVD player
Set-top box or digital tuner
11
◆ Connecting to a video player, etc.
Using the VIDEO terminal
1. Connect one end (yellow) of a commercially available video
cable to the VIDEO input terminal of this projector.
2. Connect the other end (yellow) of the video cable to the
VIDEO output terminal of the video equipment.
Video player, etc.
To VIDEO
output terminal
2
COMPONENT
Y
PB/CB
VIDEO
1 To
input terminal
PR/CR
S-VIDEO
Video cable
(commercially available)
VIDEO
Using the S-VIDEO terminal
1. Connect one end of the commercially available S-video
cable to the S-VIDEO input terminal of this projector.
2. Connect the other end of the S-video cable to the S-VIDEO
output terminal of the video equipment.
Video player, etc.
To S-VIDEO
output terminal
2
COMPONENT
Y
PB/CB
PR/CR
1 To S-VIDEO
input terminal
S-VIDEO
VIDEO
S-VIDEO cable
(commercially available)
When a TV tuner or VCR is connected:
When you use this projector with a TV tuner or VCR connected, no image may appear or a No Signal message may appear on the screen when
you change to a channel that is not being received. In this case, set the channels of the TV tuner or VCR again. To avoid this problem, use the
TV tuner or VCR with its channel skip function enabled. (Only channels that are being received will be displayed.)
◆ Connecting to a DVD player or HDTV decoder
This projector can be connected to a video equipment such as a DVD player or HDTV decoder. Be sure to connect component video output
terminals of the video equipment to the COMPONENT input terminals of this projector.
• Images may not be projected correctly depending on the type of
DVD player you use.
• It may take some time before an image is displayed on the screen
depending on the type of the input signal.
Component cable
(commercially available)
PB/CB
PR/CR
Y
COMPONENT
Y
PR/CR
PB/CB
PB/CB
PR/CR
Y
S-VIDEO
VIDEO
DVD player or HDTV decoder
12
◆ HDMI or DVI connections
You can project high-quality images by connecting the HDMI input terminal of this projector to video equipment having a HDMI output
terminal or a DVI-D output terminal. In addition, this projector supports HDCP and is able to receive encrypted digital video data that are
output from DVD players.
• HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital video data for the
purpose of copy protection.
• HDMI (High-Definition Multimedia Interface) is fully backward compatible with computers, displays and consumer electronics equipments
incorporating the DVI standards.
• Depending on the video equipment you wish to connect, this projector may not display any image or not operate correctly. In such cases,
refer to the instruction manual for the connected video equipment.
Equipment having a DVI-D terminal
Equipment having a HDMI terminal
AC IN
HDMI
SERIAL
D-SUB
USB
TRIGGER
To DVI-D terminal
To HDMI terminal
To HDMI terminal
DVI-HDMI conversion cable
(commercially available)
HDMI cable (commercially available)
When you connect this projector and DVI-Digital equipment (such as DVD player) by using the HDMI
terminal or DVI-D terminal, black color may appear light and pale depending on the type of the connected
equipment.
• This depends on the black level setting of the connected equipment. There are two kinds of methods to digitally transfer image data, in
which different black level settings are employed respectively. Therefore, the specifications of the signals output from DVD players differ
depending on the type of the digital data transfer method they use.
• Some DVD players are provided with a function to switch the methods to output digital signals. If your DVD player has such function, set it
as follows:
EXPAND or ENHANCED
NORMAL
• Refer to the instruction manual of your DVD player for details.
• When your digital equipment does not have such function, adjust the BRIGHTNESS to +16 and CONTRAST to -17 in the IMAGE menu of
this projector, or adjust the black color by viewing the image.
◆ D-SUB connections
You can project high-quality images by connecting the D-SUB terminal of this projector to video equipment having a D-SUB output terminal
or BNC terminal.
Equipment having a BNC terminal
Equipment having a D-SUB terminal
AC IN
SERIAL
To BNC terminal
D-SUB
HDMI
USB
To D-SUB terminal
TRIGGER
To D-SUB terminal
RGB cable
BNC to D-SUB cable (commercially available)
• Use the supplied RGB cable when connecting the projector and the equipment.
• For video equipment having a BNC terminal, use a commercially available BNC to D-SUB cable when connecting to this projector.
13
◆ Connecting to a computer
Important
• Make sure that the power of the projector and that of the computer are turned off.
• When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor.
• This projector may not display any image or not operate correctly depending on the computer you wish to connect. In such
cases, refer to the instruction manual of the connected computer.
For analog connections:
To D-SUB terminal
1
To monitor port
2
RGB cable
1. Connect one end of the supplied RGB cable to the D-SUB
terminal of this projector.
2. Connect the other end of the RGB cable to the monitor port
of the computer.
• Additional devices, such as a conversion connector and an
analog RGB output adapter, are required depending on the type
of the computer to be connected.
• This projector does not support 3-line signals (SYNC-ONGREEN signals).
COMPONENT
HDMI
Y
D-SUB
SERIAL
PB/CB
PR/CR
S-VIDEO
USB
TRIGGER
VIDEO
For digital connections:
To HDMI terminal
1
2
To DVI
terminal
DVI-HDMI
conversion cable
(commercially
available)
COMPONENT
HDMI
SERIAL
Y
D-SUB
PB/CB
S-VIDEO
USB
TRIGGER
VIDEO
14
PR/CR
1. Connect one end of a commercially available DVI-HDMI
conversion cable to the HDMI terminal of this projector.
2. Connect the other end of the DVI-HDMI conversion cable to
the DVI terminal of the computer.
• Additional devices, such as a conversion connector and an
analog RGB output adapter, are required depending on the type
of the computer to be connected.
• When viewing images being input from a digital-connected
computer, press the HDMI button on the remote control.
• Turn on the power of the projector before that of the computer.
• Using a long cable may decrease the quality of projected
images.
• The signal input from the HDMI terminal does not output
through the D-SUB terminal.
◆ TRIGGER terminal
The TRIGGER terminal on the rear of the projector is a terminal that outputs 12 V signal to control an externally connected equipment when
images are projected.
To use the TRIGGER terminal, set TRIGGER OUT to ON in the
SETUP menu. (The factory default is OFF.) Use the following
steps to change the setting.
COMPONENT
Y
HDMI
AC IN
SERIAL
PB/CB
PR/CR
D-SUB
S-VIDEO
USB
TRIGGER
VIDEO
With the SETUP menu:
(See page 23 for menu setting.)
1. Display the SETUP menu.
2. Select TRIGGER OUT by pressing the
3. Select ON by pressing the
To TRIGGER terminal
or
or
button.
button.
To exit from the menu:
4. Press the MENU button several times.
Ring (NC)
• Do not use the signal output from the TRIGGER terminal as
a power for other equipment.
• Do not link the TRIGGER terminal with an audio terminal
of other equipment. This may cause a damage.
• The rated current for the TRIGGER terminal is 200 mA. If
you use a current exceeding this rating, a failure may occur.
• For information about electric screens, please contact screen
manufacturers.
Tip (12 V)
Sleave (ground 0 V)
◆ Plugging in the power cable
For US
For Europe
HDMI
AC IN
SERIAL
Earthing
terminal
D-SUB
USB
SERIAL
TRIGGER
1
HDMI
AC IN
USB
TRIGGER
2
Power cable
Earthing
terminal
D-SUB
1
2
Power cable
1. Plug the supplied power cable into the AC IN of this projector.
2. Plug the other end of the power cable into a power outlet.
• The power cables for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.
• This projector uses the power plug of three-pin grounding type. Do not take away the grounding pin from the power plug. If the power
plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.
• The provided power cable for the U.S. is rated at 120 V. Never connect this cable to any outlet or power supply using other voltages or
frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power cable separately.
15
6 Projection
◆ Viewing video images
Preparation:
• Always remove the lens cap before operating the projector.
• Turn on the power of the connected video equipment.
FOCUS ring
ZOOM ring
ON ( I )
button
HDMI button
ON
POWER
STANDBY
ASPECT
AUTO
ASPECT
HIDE
NORMAL
SQUEEZ
S. ZOOM
COMP.
VIDEO
HDMI
INPUT
D-SUB button
STANDBY/ON
button
D-SUB
S-VIDEO
COMP. button
VIDEO button
S-VIDEO button
ENTER
STANDBY/ON
POWER
STATUS
AUTO SYNC
ENTER
MENU
KEYSTN
MENU
MEMORY
DIGITAL CINEMA PROJECTOR DPX-830
1
2
3
CONT.
BRIGHT
C.TEMP
SHARP
IRIS
GAMMA
SETTING
D-SUB/HDMI
button
RDP-81
VIDEO/S/COMP.
button
1. Confirm the POWER indicator lights up red.
• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the STANDBY/ON
button may not work after the power cable is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the
STANDBY/ON button to turn back on the POWER indicator.
2. Press the STANDBY/ON ( ) button on the projector or ON ( I ) button on the remote control.
• It may take about one minute for the lamp to light up.
• The lamp fails to light up on rare occasions. If this happens, wait for a few minutes and then try again.
• Do not cover the lens with the lens cap while the lamp is on.
3. Select an input source.
• Press the VIDEO/S/COMP. or D-SUB/HDMI button on the projector, or press one of the input selector buttons (VIDEO, S-VIDEO,
COMP., HDMI, or D-SUB) on the remote control to select the input you desire. Be sure to select the input source that is corresponding
to the terminal in use.
–The input source is switched to VIDEO, S-VIDEO or COMPONENT at every press of the VIDEO/S/COMP. button on the projector.
–The input source is switched between D-SUB and HDMI at every press of the D-SUB/HDMI button on the projector.
• There may be a delay before an image is displayed on the screen depending on the type of the input signal.
• Some images become easier to view when the setting of aspect ratio is changed (see page 18).
4. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their
specified sizes.
5. Adjust the position of the projector so that the projector and the screen are perpendicular to each other (see page 8).
• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle (see page 8).
6. Adjust the size of the projected image by turning the ZOOM ring.
7. Adjust the focus by turning the FOCUS ring.
Repeat steps 4 to 7, if necessary.
Important
• When a 4:3 image is continuously displayed for a long time before displaying a 16:9 image, the afterimages of the black
bars on each side may appear on the 16:9 image screen. Consult your dealer in this case.
• Do not display a still picture for a long time because the afterimages may persist on the screen.
16
To stop projecting:
1. Press the STANDBY/ON ( ) button on the projector or the STANDBY (
• A confirmation message is displayed.
• To cancel the procedure, wait a while or press the MENU button.
) button on the remote control.
2. Press the STANDBY/ON ( ) button on the projector or the STANDBY ( ) button on the remote control again.
• The lamp goes out and the projector goes into a cooling period. In this condition, the POWER indicator turns red and the STATUS
indicator blinks green.
3. Wait about one minute for the STATUS indicator to be off and the POWER indicator to be steadily lit in red.
• During this one minute period, the intake and exhaust fans rotate to cool the lamp.
• The fan may make loud sounds during a cooling period.
Caution
• Do not unplug the power cable while the STATUS indicator is blinking. Unplugging the power cable immediately after use
may damage the lamp or reduce lamp life.
KEYSTONE adjustment
Use to correct vertical and horizontal image distortion caused by
tilting the projector.
1. Press the KEYSTONE (ENTER) button on the control area
of the projector or the KEYSTN button on the remote
control.
2. Adjust the projection angle by pressing
buttons as shown.
,
,
Press
button
,
To exit from the menu:
3. Press the KEYSTONE (ENTER) button on the control area
of the projector or the KEYSTN button on the remote control
again.
Press
button
Press
button
Press
button
Important
• When the keystone adjustment is applied, the correct aspect ratio may not be obtained.
• When the keystone adjustment is applied, the resolution lowers. In addition, vertical stripes appear and straight lines bend
in images with complicated patterns. To prevent such symptoms, keep the screen and the projector perpendicular to each
other as much as possible.
• When the keystone adjustment is applied, the distorted image may appear for a while.
• The projected image may be distorted depending on the setting value of the keystone adjustment and the type of the input
signals. In such cases, adjust the setting value within the range where the projected image is not distorted.
• The setting value displayed at the time of the keystone adjustment may vary depending on the type of the input signal.
IRIS button
The IRIS function adjusts the contrast optically by opening and
closing the lens aperture. Select OPEN to increase the brightness of
the image. Select CLOSE to deepen the black level of the image while
reducing the brightness.
1. Press the IRIS button on the remote control.
• The current setting appears.
IRIS
:
CONT.
BRIGHT
C.TEMP
GAMMA
SHARP
IRIS
IRIS button
SETTING
CLOSE
2. Change the setting by pressing the IRIS button again while
the current setting is being displayed.
IRIS
:
OPEN
17
Examples of the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Display pattern changes according to the
setting of SCREEN ASPECT in the INITIAL menu. The following table is in the case of 16:9 screen. Change the setting according to the type
of the input video signal.
: Image area
NORMAL
Original image size
Displays the image
while keeping the
input aspect ratio.
SQUEEZE
Squeezed image is
expanded to 16:9.
SUBTITLE ZOOM*1
Cinema scope image
is enlarged and
displayed together
with subtitles.
ZOOM*1
Vista image is
enlarged and
displayed together
with subtitles.
SMART ZOOM*2
Image is enlarged to
16:9 while the center
aspect ratio remains
unchanged.
THROUGH
Input signal is
displayed in its
original size.
4:3 image (480i, 576i,
480p, 576p, and PC)
4:3 Squeezed
(480i, 576i, 480p, 576p)
Sub Title
Sub Title
4:3 LetterBox
(CinemaScope with subtitles)
(480i, 576i, 480p, 576p)
Sub Title
Sub Title
Sub Title
Sub Title
Sub Title
4:3 LetterBox (Vista image)
(480i, 576i, 480p, 576p)
Not available.
Not available.
Not available.
16:9 image (720p, 1080i)
*1: Available only when the input signal is 480p or 576p.
*1: When ASPECT is set to SUBTITLE ZOOM or ZOOM, display position can be changed with the
or button on the remote control.
*2: OVER SCAN and BLACK MASK in the SIGNAL menu are not available in the SMART ZOOM mode.
• Bold frames
are recommended modes.
• This projector is equipped with a function to change the aspect ratio. If you select an aspect ratio that is inconsistent with that of the input signal, images around the screen edges
may be hidden or deformed. When viewing original video works reflecting the authors’ intentions, you are recommended to keep their aspect ratios unchanged.
• It may be an infringement of the rights protected by the copyright law to project images compressed or enlarged by changing the aspect ratio in public areas, such as inside and
outside shops and hotels, for commercial or public viewing purposes.
Setting the aspect ratio
With the remote control:
With the INITIAL menu:
1. ASPECT button
• Every time you press the ASPECT button, the aspect mode
changes from DEFAULT to NORMAL, SQUEEZE,
SUBTITLE ZOOM, ZOOM, SMART ZOOM, THROUGH
and back to DEFAULT. DEFAULT is automatically set to either
NORMAL or SQUEEZE depending on the input signal.
(See page 22 for how to set the menus.)
1. Display the INITIAL menu.
2. Select ASPECT by pressing the
or
* The available aspect mode differs depending on the input signals.
2. NORMAL, SQUEEZ, S.ZOOM button
• NORMAL, SQUEEZ, S.ZOOM (SMART ZOOM) buttons on
the remote control enable you to select the aspect mode
directly.
* Depending on the input signals, these buttons may not function.
TV60
INITIAL
ASPECT
DEFAULT
To exit from the menu:
4. Press the MENU button several times.
ON
POWER
STANDBY
ASPECT
ASPECT button
NORMAL button
18
AUTO
ASPECT
HIDE
NORMAL
SQUEEZ
S. ZOOM
S.ZOOM button
SQUEEZ button
button.
3. Select your desired aspect ratio by pressing the
button.
or
◆ Viewing computer images
Preparation:
• Always remove the lens cap before operating the projector.
• Turn on the power of the connected computer.
FOCUS ring
ZOOM ring
ON ( I ) button
ON
POWER
STANDBY
ASPECT
AUTO button
AUTO
ASPECT
HIDE
NORMAL
SQUEEZ
S. ZOOM
HDMI
COMP.
VIDEO
INPUT
D-SUB button
STANDBY/ON
button
D-SUB
S-VIDEO
ENTER
STANDBY/ON
POWER
STATUS
AUTO SYNC
ENTER
MENU
KEYSTN
MENU
MEMORY
DIGITAL CINEMA PROJECTOR DPX-830
AUTO SYNC
button
1
2
3
CONT.
BRIGHT
C.TEMP
SHARP
IRIS
GAMMA
SETTING
D-SUB/HDMI
button
RDP-81
1. Confirm the POWER indicator lights up red.
• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the STANDBY/ON
button may not work after the power cable is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the
STANDBY/ON button to turn back on the POWER indicator.
2. Press the STANDBY/ON ( ) button on the projector or ON ( I ) button on the remote control.
• It may take about one minute for the lamp to light up.
• The lamp fails to light up on rare occasions. If this happens, wait for a few minutes and then try again.
• Do not cover the lens with the lens cap while the lamp is on.
3. Select an input source.
• Press the D-SUB/HDMI button on the projector or the D-SUB button on the remote control that is corresponding to the terminal in use.
–The input source is switched between D-SUB and HDMI at every press of the D-SUB/HDMI button on the projector.
• There may be a delay before an image is displayed on the screen depending on the type of the input signal.
• Images may not be projected in the correct position depending on the type of the input signal. If this happens, press the AUTO SYNC
button on the projector or the AUTO button on the remote control (see page 20).
4. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their
specified sizes.
5. Adjust the position of the projector so that the projector and the screen are perpendicular to each other (see page 8).
• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle (see page 8).
6. Adjust the size of the projected image by turning the ZOOM ring.
7. Adjust the focus by turning the FOCUS ring.
Repeat steps 4 to 7, if necessary.
Important
• When a 4:3 image is continuously displayed for a long time before displaying a 16:9 image, the afterimages of the black
bars on each side may appear on the 16:9 image screen. Consult your dealer in this case.
• Do not display a still picture for a long time because the afterimages may persist on the screen.
19
To stop projecting:
1.
Press the STANDBY/ON ( ) button on the projector or the STANDBY (
• A confirmation message is displayed.
• To cancel the procedure, wait a while or press the MENU button.
) button on the remote control.
2. Press the STANDBY/ON ( ) button on the projector or the STANDBY ( ) button on the remote control again.
• The lamp goes out and the projector goes into a cooling period. In this condition, the POWER indicator turns red and the STATUS
indicator blinks green.
3. Wait about one minute for the STATUS indicator to be off and the POWER indicator to be steadily lit in red.
• During this one minute period, the intake and exhaust fans rotate to cool the lamp.
• The fans may make loud sound during the cooling period.
Caution
• Do not unplug the power cable while the STATUS indicator is blinking. Unplugging the power cable immediately after use
could damage the lamp or reduce lamp life.
AUTO / AUTO SYNC buttons
When the image being input from the computer is displaced, carry out the following procedure:
1. Disable the screen saver if it has been enabled.
2. Display a bright image (such as a full-screen display of the Recycle Bin window).
3. Press the AUTO button on the remote control or the AUTO SYNC button on the projector.
The projector automatically makes optimum positional settings for the input signal.
• If the image is not projected in the correct position even after you press the AUTO or AUTO SYNC button several times, change the
settings in the SIGNAL menu to put the image in the correct position (see page 31).
• When you carry out this procedure with a dark image, the image may be displaced.
Connecting to a notebook computer
When the projector is connected to a notebook computer, images may not be projected in some cases. If this happens, set the computer so that
it can output signals externally. The setting procedure varies depending on the type of the computer. Refer to the instruction manual of your
computer.
20
7 Menu
◆ Menu overview
Menus are not displayed when no signal is received by the projector.
IMAGE
GAMMA
CONTRAST
BRIGHTNESS
COLOR TEMP.
SATURATION *1*3
HUE
*1*3
SHARPNESS *1*3
BrilliantColor TM
SET UP
SCREEN ASPECT
VERTICAL LOCATION
LAMP MODE
AUTO POWER ON
AUTO POWER OFF
SPLASH SCREEN
HIDE SCREEN COLOR
LOCATION
TRIGGER OUT
TEST PATTERN
INITIAL
*2
ASPECT
MENU POSITION
PROGRESSIVE MODE *3
COLOR SYSTEM *3
SET UP LEVEL *1*3
SCART INPUT *3
LANGUAGE
RESET ALL
SIGNAL
HORIZ.POSITION *3
VERT.POSITION *3
*3
PHASE
TRACKING *1*3
*3
OVER SCAN
D-SUB INPUT *3
*1
BLACK MASK
SYNC NOISE MASK *1*3
A/D SETTING
After selecting the items marked with
DEFAULT
DYNAMIC
STANDARD
CINEMA
CUSTOM1 , CUSTOM2
± 30
± 30
NATIVE
HIGH
MID
LOW
CUSTOM
± 10
± 10
±5
ON, OFF
GAMMA - CUSTOM1
GAMMA - CUSTOM2
REFERENCE
H
M
L
DYNAMIC, STANDARD, CINEMA
±5
±5
±5
CONTRAST R
CONTRAST G
CONTRAST B
BRIGHTNESS R
BRIGHTNESS G
BRIGHTNESS B
COLOR TEMP. - CUSTOM
± 30
± 30
± 30
± 30
± 30
± 30
16:9, 4:3
± 26
STANDARD, CINEMA
ON, OFF
OFF, 5, 10, 15, 30, 60 min
ON, OFF
BLUE, BLACK
FRONT/TABLE, REAR/TABLE, FRONT/CEILING, REAR/CEILING
ON, OFF
CROSS HATCH , WHITE , BLACK
DEFAULT, NORMAL, SQUEEZE, SUBTITLE ZOOM, ZOOM, SMART ZOOM, THROUGH
UPPER LEFT, UPPER RIGHT, LOWER LEFT, LOWER RIGHT
AUTO, VIDEO
AUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60
DEFAULT, 0%, 3.75%, 7.5%
ON, OFF
, ENGLISH, ESPANÕL, DEUTSCH, FRANÇAIS, ITALIANO,
EXECUTE
*2
0 - 999
*2
0 - 999
0 - 31
*2
0 - 9999
*2
100 - 90%
AUTO, RGB, COMPONENT
EXECUTE
ON
OFF
EXECUTE
BLACK MASK
SYNC NOISE MASK
A/D SETTING
*1
TOP
*1
BOTTOM
*1
LEFT
*1
RIGHT
BEGIN
END
CLAMP POSITION *3
CLAMT WIDTH *3
VERT. SYNC *1
*3
LPF
0 - 38
0 - 38
0 - 95
0 - 95
0 - 99
0 - 99
*2
0 - 63
*2
1 - 63
AUTO, OFF
ON, OFF
, press the ENTER button.
*1: Not available with certain signals.
*2: The defaul value and the setting range differ depending on the input signal.
*3: See next page for availability and unavailability.
21
SATURATION
HUE
SHARPNESS
PROGRESSIVE MODE
COLOR SYSTEM
SET UP LEVEL
SCART INPUT
HORIZ. POSITION
VERT. POSITION
PHASE
TRACKING
OVER SCAN
D-SUB INPUT
SYNC NOISE MASK
Unavailable when the input source is HDMI or D-SUB source is an RGB signal.
Available only when the VIDEO or S-VIDEO source is NTSC or 4.43NTSC signal.
Unavailable when the D-SUB or HDMI source is a computer signal.
Available only when the input signal is TV50, TV60, 480i or 576i.
Available only when the input source is VIDEO or S-VIDEO.
Unavailable when the input source is HDMI, and also when the D-SUB source is a computer signal.
Available only when the input source is D-SUB.
Unavailable when the input source is HDMI.
Unavailable when the input source is HDMI.
Available when the input source is COMPONENT and D-SUB, except RGBCs (576i) signal.
Available only when the D-SUB source is a computer signal.
Unavailable when the VIDEO or S-VIDEO source is NTSC, 4.43NTSC, PAL-M, PAL-60 signal.
Available only when the input source is D-SUB except RGBCs (576i) signal.
Available when the input source is COMPONENT 720p, 1080i signal and D-SUB 720p, 1080i computer
signal.
Available when the input source is COMPONENT and D-SUB, except RGBCs (576i) signal.
Available when the input source is COMPONENT and D-SUB, except RGBCs (576i) signal.
Available only when the COMPONENT or D-SUB source is a 480i/p, 576i/p signal, except RGBCs (576i)
signal.
CLAMP POSITION
CLAMP WIDTH
LPF
How to set the menus
Following describe how to set AUTO POWER OFF time as an
example.
1. Press the MENU button.
• If no signal is input, the menu does not appear.
TV60
4. Press the
or
button to select an item to adjust.
AUTO POWER ON
OFF
AUTO POWER
OFF
SPLASH
SCREEN
OFF
ON
5. Set the selected item by pressing the
IMAGE
2. Press the
or
button to select a menu to use.
• SETUP menu is selected in this example.
TV60
AUTO POWER
ON
AUTO POWER
OFF
SPLASH
SCREEN
or
button.
OFF
30 min
ON
To exit from the menu:
SETUP
6. Press the MENU button several times.
3. Press the ENTER button (or
button).
Important
TV60
SETUP
SCREEN ASPECT
VERTICAL
LOCATION
LAMP MODE
AUTO POWER
ON
AUTO POWER
OFF
22
16:9
0
CINEMA
OFF
OFF
• If the MENU button does not function, unplug the
power cable from the wall outlet. Wait about 10
minutes, plug the power cable in, and try again.
◆ Menu settings
The following items in the menus enable you to customize this projector.
1. IMAGE menu
TV60
IMAGE
GAMMA
DEFAULT
CONTRAST
0
BRIGHTNESS
0
COLOR TEMP.
MID
SATURATION
0
HUE
0
SHARPNESS
0
BrilliantColor TM
OFF
ITEM
SETTING
FUNCTION
GAMMA
DEFAULT
The appropriate gamma mode is automatically selected depending on the input signal. Select
DEFAULT for normal use.
DYNAMIC
Select to secure the contrast even when the room lighting is increased to some extent.
STANDARD
Select to gain the halftone to make the skin color more vibrant even in a dark scene. This
mode is suitable for TV viewing.
CINEMA
Select when watching movies in dim lighting as in a theater.
CUSTOM 1
CUSTOM 2
,
Use to customize the gamma mode (see page 27).
CONTRAST
± 30
Use to adjust the contrast of the projected image (see page 27).
BRIGHTNESS
± 30
Use to adjust the brightness of the projected image (see page 27).
COLOR TEMP.
NATIVE
Select this option when projecting the image without adjusting the color temperature.
H
Select for a high color temperature (see page 28).
M
Select for a balanced color temperature (see page 28)
L
Select for a low color temperature (see page 28)
CUSTOM
Use to customize the color temperature (see page 28)
SATURATION
± 10
Use to adjust the color richness of the projected image (see page 29).
HUE
± 10
Use to adjust the color tint of the projected image (see page 29).
SHARPNESS
±5
Use to adjust the sharpness of the projected image (see page 29).
BrilliantColor
ON, OFF
Select ON to increase the brightness of the projected image by boosting the midtone color
levels while ensuring more vibrant colors. Select OFF when viewing the scene (i.e. a live
indoor concert) that is already high in contrast. In such a case, the color and contrast appears
more natural with BrilliantColor deactivated.
TM
• DEFAULT depends on the two signal types below:
1. Video signals (TV50, TV60, 480i/p, 576i/p, 720p50/60, 1080i50/60)
2. Computer signals (VGA, XGA, etc.)
See page 40 for a complete listing for the signal specifications.
• Memory function saves up to 3 patterns of the IMAGE menu for each input terminal (see page 30).
• BrilliantColorTM uses BrilliantColorTM technology of Texas Instruments of USA.
23
2. SETUP menu
TV60
SETUP
16:9
SCREEN ASPECT
VERTICAL
LOCATION
0
LAMP MODE
CINEMA
AUTO POWER
ON
AUTO POWER
OFF
SPLASH
SCREEN
HIDE SCREEN
COLOR
LOCATION
OFF
OFF
ON
BLUE
FRONT/TABLE
TRIGGER OUT
TEST PATTERN
OFF
CROSS HATCH
ITEM
SETTING
FUNCTION
SCREEN ASPECT
16:9, 4:3
Use to select the screen size.
VERTICAL
LOCATION
± 26
Use to adjust the position (height) of the projected image.
LAMP MODE
STANDARD
Select when using the projector in a bright environment.
CINEMA
Select to moderate the intensity of the lamp. The operating sound is reduced and the lamp
lifetime becomes longer.
AUTO POWER ON
ON, OFF
When ON is selected, the lamp is automatically lit when the power cord is plugged in the
wall outlet. Select ON when using the projector mounted on the ceiling.
AUTO POWER
OFF
OFF, 5 – 60min
Use to set the time elapsed before the projector enters the stand-by mode when there is no
signal input from the source.
SPLASH
SCREEN
ON, OFF
Select ON to display the splash screen when the power is turned on
HIDE SCREEN
COLOR
BLUE, BLACK
Use to select the backbround when there is no signal inputted from the selected source.
LOCATION
FRONT/TABLE
Select when viewing images from the front with the projector installed on the floor.
REAR/TABLE
Select when viewing images projected from behind of the screen with the projector installed
on the floor.
FRONT/CEILING
Select when viewing images from the front with the projector installed on the ceiling.
REAR/CEILING
Select when viewing images projected from behind of the screen with the projector installed
on the ceiling.
TRIGGER OUT
ON, OFF
Selec ON when there is a signal received at the TRIGGER OUT terminal
TEST PATTERN
CROSS HATCH
Select to display the test cross hatched pattern.
WHITE
Select to display the maximum brightness image.
BLACK
Select to display the minimum brightness image.
• Do not change the setting of the LAMP MODE frequently. This could damage the lamp.
• To exit from the TEST PATTERN, press any buttons on the remote control.
24
3. INITIAL menu
TV60
INITIAL
ASPECT
MENU POSITION
DEFAULT
UPPER LEFT
PROGRESSIVE
MODE
AUTO
COLOR SYSTEM
SET UP LEVEL
AUTO
DEFAULT
OFF
SCART INPUT
LANGUAGE
RESET ALL
ENGLISH
EXECUTE
ITEM
SETTING
FUNCTION
ASPECT
DEFAULT
The appropriate aspect ratio is automatically selected depending on the input signal. Select
DEFAULT for normal use.
NORMAL
Select to project images with an aspect ratio of 4:3.
SQUEEZE
Select to project images with an aspect ratio of 16:9.
SUBTITLE ZOOM
Select to project subtitled letter box format software.
ZOOM
Select to enlarge and project images of CinemaScope size or Vista size.
SMART ZOOM
Select to stretch the left and right edges of a 4:3 image without altering the image center to
project a 16:9 image that fills the screen.
THROUGH
Select to project images in their original size as input.
MENU POSITION
4 positions
Use to change the position of the menu being displayed on the screen.
PROGRESSIVE
MODE
AUTO
Detects the video and film contents and convert into opitmized progressive frames
automatically.
VIDEO
Force to convert using motion-adaptive I/P conversion for video contents only.
COLOR SYSTEM
8 options
When AUTO is selected, the appropriate video format is automatically selected depending on
the input signal. If the image is not displayed correctly, select the desired video format manually.
SET UP LEVEL
DEFAULT, 0%,
3.75%, 7.5%
Select the black level of the projected image. SET UP LEVEL is automatically set to 7.5%
when you select any language except
(Japanese) in the LANGUAGE menu. Select
DEFAULT for normal use.
SCART INPUT
ON, OFF
Select ON when connecting the projector to the equipment having a SCART terminal that can
output RGB signal. SCART terminal is used mainly in Europe. Select OFF for normal use.
LANGUAGE
10 languages
Use to select the language used in the menu.
RESET ALL
EXECUTE
Use to reset the settings of the menu (excluding LANGUAGE) to its factory presets. It may
take few seconds that the projector is reset to its factory presets.
• DEFAULT depends on the two signal types below:
1. Video signals (TV50, TV60, 480i/p, 576i/p, 720p50/60, 1080i50/60)
2. Computer signals (VGA, XGA, etc.)
See page 40 for a complete listing for the signal specifications.
25
4. SIGNAL menu
TV60
SIGNAL
HORIZ. POSITION
0 - 999
VERT. POSITON
0 - 999
PHASE
0 - 31
TRACKING
0 - 999
OVER SCAN
100 - 90%
D-SUB INPUT
AUTO
BLACK MASK
EXECUTE
SYNC NOISE
MASK
ON
A/D SETTING
EXECUTE
ITEM
SETTING
FUNCTION
HORIZ. POSITION
0 – 999*
Use to adjust the horizontal position of the projected image.
VERT. POSITION
0 – 999*
Use to adjust the vertical position of the projected image. The adjustable range varies
depending on the type of the input signal. In some cases, the image may stay in the same
position even when the setting value is changed.
PHASE
0 – 31*
Use to eliminate flickering or blur, if it appears while viewing the projected image.
TRACKING
0 – 9999*
Use to eliminate vertical wide stripes, if it appears, while viewing the projected image.
OVER SCAN
100% – 90%*
Use to adjust the over scan ratio for the video signals.
D-SUB INPUT
AUTO
When the projector detects the three-wire system (YCBCR/ YPBPR) or five-wire system
(RGBHV), it automatically selects either COMPONENT or RGB accordingly.
RGB
Select this option when connecting the projector to high definition video equipment having
R, G, and B output terminals.
COMPONENT
Select this option when connecting the projector to a DVD player or other equipments having
Y, CB, and CR (or Y, PB, and PR) component video output terminals.
EXECUTE
Use to adjust the image when the noise appears on the projected image.
BLACK MASK
SYNC NOISE MASK
A/D SETTING
TOP
Adjust the image when the noise appears on the top part of the image.
BOTTOM
Adjust the image when the noise appears on the bottom part of the image.
LEFT
Adjust the image when the noise appears on the left part of the image.
RIGHT
Adjust the image when the noise appears on the rigtht part of the image.
ON
, OFF
Use to adjust the image when flagging occurs near the top of the screen.
BEGIN
Use to adjust the start of the sync noise mask position.
END
Use to adjust the end of the sync noise mask position.
EXECUTE
Use to adjust the Analog Digital conversion parameters.
CLAMP POSITION Use to correct solid white or solid black in the projected image.
CLAMP WIDTH
Use to correct solid black in the projected image.
VERT. SYNC
Use to adjust the image when its motion does not run smoothly.
LPF
Use to reduce the streak noise appeared on the image. (see page 29).
* The default value and the setting range differ depending on the input signals.
• Horizontal strips may appear on the enlarged projected image.
• When changing a horizontal or vertical position to a large extent, noise may appear.
• When you select COMPONENT as an input source, the setting of D-SUB INPUT will be changed to COMPONENT automatically.
• OVER SCAN and BLACK MASK are not available when the aspect ratio is set to SMART ZOOM (see page 18).
• OVER SCAN is not available when the aspect ratio is set to THROUGH (see page 18).
• If you increase the OVER SCAN setting when the projector is receiving the video signals, noise may appear on the screen. In such case,
decrease the OVER SCAN setting.
26
8 Adjusting video images
◆ Selecting the gamma mode (GAMMA)
You can select a preset gamma mode by using the menu (see page 23).
1. Display the IMAGE menu.
2. Select GAMMA by pressing the
or
button.
3. Select your desired gamma mode by pressing the
• Select DEFAULT for normal use.
or
button.
To exit from the menu:
4. Press the MENU button several times.
◆ Customizing the gamma mode (GAMMA)
To customize and store the gamma mode, carry out the following procedure.
1. Select GAMMA in the IMAGE menu.
7. Repeat step 5 to 6 for optimum adjustiment result.
2. Press the
or
button to selcet CUSTOM 1
or
CUSTOM 2 .
3. Press the ENTER button.
• The GAMMA-CUSTOM1 menu appears as shown.
To exit from the menu:
8. Press the MENU button several times.
To activate the customized gammma mode:
1. Press GAMMA button on the remote control.
• The current setting appears.
GAMMA - CUSTOM1
CINEMA
REFERENCE
C
H
1
0
M
0
L
0
GAMMA
:
DEFAULT
2. Press the
or
button to select GAMMA - CUSTOM1
or GAMMA - CUSTOM2.
4. Press the
or
button to select REFERENCE.
5. Select the desired gamma mode from DYNAMIC,
STANDARD, or CINEMA.
GAMMA
:
CUSTOM1
To exit from the menu:
6. Press the
or
button to select an item from H (High),
M (Middle), or L (Low), and then adjust the level of each
item by pressing the
or
button.
3. Press the GAMMA button on the remote control.
◆ Adjusting brightness (CONTRAST and BRIGHTNESS)
You can make adjustments for the brightness of the projected image using the menu (see page 23).
1. Display the IMAGE menu.
2. Select CONTRAST or BRIGHTNESS by pressing the
3. Adjust the selected item by pressing the
or
or
button.
button.
To exit from the menu:
4. Press the MENU button several times.
CONTRAST
Select to adjust the bright areas (white level) in the image. Increase this figure by pressing the
image or decrease this figure by pressing the
button to reduce the contrast of the image.
button to increase the contrast clarity of the
BRIGHTNESS
Select to adjust the overall brightness of the image. Increase this figure by pressing the
figure by pressing the
button to render a darker image.
button to render a brighter image or decrease this
27
◆ Selecting the color temperature (COLOR TEMP.)
You can select a preset color temperature (white tone) using the menu (see page 23).
1. Display the IMAGE menu.
2. Select COLOR TEMP. by pressing the
or
button.
3. Select your desired color temperature by pressing the
or
button.
To exit from the menu:
4. Press the MENU button several times.
◆ Customizing the color temperature (COLOR TEMP.)
To customize and store the color temperature, carry out the following procedure.
1. Select COLOR TEMP. in the IMAGE menu.
6. Repeat step 4 and 5 for optimum adjustment results.
2. Press the
or
button to select CUSTOM .
3. Press the ENTER button.
• The COLOR TEMP. - CUSTOM menu appears as shown.
To exit from the menu:
7. Press the MENU button several times.
To activate the stored color temperature settings:
COLOR TEMP. - CUSTOM
CONTRAST R
0
CONTRAST
G
CLAMP WIDTH
1
0
CONTRAST B
0
BRIGHTNESS R
0
BRIGHTNESS G
0
BRIGHTNESS B
0
1. Press C.TEMP on the remote control.
• The current setting appears.
COLOR TEMP.
2. Press the
or
5. Press the
item.
or
NATIVE
button to select CUSTOM
COLOR TEMP.
4. Press the
or
button to select an item from
CONTRAST R (red), CONTRAST G (green),
CONTRAST B (blue), BRIGHTNESS R (red),
BRIGHTNESS G (green), and BRIGHTNESS B (blue).
:
.
: CUSTOM
To exit from the menu:
3. Press the C.TEMP button on the remote control.
button to adjust the value of each
About color temperature
There are different kinds of white color. Color temperature is a way to show the differences in white. With the higher color temperature, white
area of the image appears reddish, with the lower color temperature, white area of the image appears bluish. This projector adjusts the color
temperature by changing the values of the blue and red contrasts.
To raise the color temperature:
Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).
To reduce the color temperature:
Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).
Important
• If you set all of CONTRAST R, G and B to negative value, the original brightness of the image can not be obtained even
when you maxmize CONTRAST in the IMAGE menu.
28
◆ Adjusting color (SATURATION and HUE)
You can adjust the color of the projected image using the menu (see page 23).
1. Display the IMAGE menu.
2. Select SATURATION or HUE by pressing the
or
3. Adjust the selected item by pressing the
button.
or
button.
To exit from the menu:
4. Press the MENU button several times.
SATURATION
Use to adjust the richness of the color in the projected image. Increase this figure by pressing the
this figure by pressing the
button to render a lighter color.
• Unavailable when the input source is HDMI or D-SUB source is an RGB signal.
button to render a richer color or decrease
HUE
Use to adjust the tint of the projected image. Increase this figure by pressing the button to render a greenish image or decrease this figure by
pressing the
button to render a reddish image.
• Available only when the VIDEO or S-VIDEO source is NTSC or 4.43NTSC signal.
◆ Sharpening or softening images (SHARPNESS)
You can adjust the sharpness of the projected image using the menu (see page 23).
1. Display the IMAGE menu.
2. Select SHARPNESS by pressing the
or
3. Adjust the selected item by pressing the
• Increase this figure by pressing the
image noise.
button.
or
button.
button to render a sharper image, or reduce it by pressing the
button to give a softer image with less
To exit from the menu:
4. Press the MENU button several times.
◆ LPF (Progressive filter)
You can select whether or not to enable the LPF. This item is normally set to OFF.
Vertical or horizontal streak noise may appear on the projected image depending on the type of the DVD player you use. In such cases, you can
reduce such streak noise by enabling the LPF. However, projected images become softened slightly.
1. Select A/D SETTING in the SIGNAL menu.
2. Press the
or
button to select EXECUTE
3. Press the ENTER button.
4. Press the
or
button to select LPF.
5. Press the
or
button to choose ON or OFF.
To exit from the menu:
EXECUTE
.
CLAMP
POSITION
0
CLAMP WIDTH
1
VERT. SYNC
OFF
LPF
OFF
6. Press the MENU button several times.
29
9 MEMORY function
◆ Saving memory settings
The memory function saves up to 3 patterns of the image quality settings for each input source. Following is the list of items that can be saved.
• GAMMA*
• SATURATION
• CONTRAST
• HUE
• BRIGHTNESS
• SHARPNESS
• COLOR TEMP.*
• BrilliantColorTM
* You can not change the customized setting in GAMMA and COLOR TEMP. for each memory number.
1. Press one of the MEMORY buttons on the remote controll where you wish to store the settings.
2. Adjust the each item listed above in the IMAGE menu.
• The settings are automatically stored.
• You can also use the picture quality adjusting bottons on the remote control (see page 6).
MENU
KEYSTN
MEMORY
1
2
3
CONT.
BRIGHT
C.TEMP
SHARP
IRIS
GAMMA
MEMORY buttons
Picture quality adjusting
buttons
SETTING
To exit from the menu:
3. Press the MENU button several times.
To activate the stored memory settings:
1. Press one of the MEMORY buttons on the remote control.
• The image quality settings that are stored in the selected memory is activated.
MEMORY 1
To exit from the menu:
2. Press the same MEMORY button that you selected in step 1.
Important
• When the input source is changed, the projector automatically reverts to the previousely selected memory setting.
• When RESET ALL in the INITIAL menu is selected, all the settings that are stored in the memory will be cleared (see page
25).
30
10 Adjusting computer images
This projector automatically and properly projects video signals supplied from the computer. However, some video signals may not be
projected depending on the type of the computer. In such cases, press the AUTO SYNC button on the projector or the AUTO button on the
remote control (see page 20). When the signal is still not projected properly, adjust the projected image using the SIGNAL menu.
◆ Adjusting computer images
Carry out the following procedures according to the symptoms.
(See page 22 for how to set the menus)
Wide strips appear................................................. Adjust TRACKING in the SIGNAL menu.
The projected image flickers or the projected image is blurred
.............................................................................. Adjust PHASE in the SIGNAL menu.
The projected image is displaced horizontally ..... Adjust HORIZ. POSITION in the SIGNAL menu. Every time the button is
pressed, the image moves to the right. Every time the button is pressed, the
image moves to the left.
The projected image is displaced vertically.......... Adjust VERT. POSITION in the SIGNAL menu. Every time the button is
pressed, the image moves down. Every time the button is pressed, the
image moves up.
The top part of the image flags ............................. Change the setting of SYNC NOISE MASK in the SIGNAL menu. Select
ON
, press the ENTER button, and adjust BEGIN or END to minimizethe
flagging.
Wide strips appear................................................. Adjust CLAMP POSITION or CLAMP WIDTH in the A/D SETTING.
The motion does not run smoothly ....................... Adjust VERT. SYNC. in the A/D SETTING. Select AUTO for normal use.
Noise appears on the right or left half of the image
.............................................................................. Adjust LEFT or RIGHT in the BLACK MASK.
Noise appears on the top or bottom part of the image
.............................................................................. Adjust TOP or BOTTOM in the BLACK MASK.
1. Display the SIGNAL menu.
2. Press the
or
button to select an item to adjust.
3. Adjust the selected item by pressing the
or
button.
To exit from the menu:
4. Press the MENU button several times.
Simple method to adjust the image position
To adjust the horizontal position:
1. Align the left edge of the image with the left side of the screen by adjusting HORIZ. POSITION. Then, align the right edge of
the image with the right side of the screen by adjusting TRACKING.
2. Repeat the previous step to complete the adjustment of the horizontal position.
To adjust the vertical position:
3. Align the upper edge of the image with the upper side of the screen by adjusting VERT. POSITION.
31
11 Replacing the lamp
This projector is equipped with a lamp to project images. This lamp is a consumable, so it may burn out or its brightness may decrease during
use. If this happens, replace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new, commercially available lamp
that is exclusive to this projector. Contact your dealer for purchase of the lamp.
Warning
• This product contains a high intensity lamp that contains a small amount of mercury. Disposal of this material may be
regulated due to environmental considerations. For disposal information in the United States, refer to the Electronic
Industries Alliance web site: www.eiae.org
• Be careful not to drop the lamp screws into the projector. Do not put a metal piece or flammable object into the projector.
Using the projector with any foreign object present inside may result in electric shock or fire. If you can’t remove the foreign
object from the inside, contact your dealer for removal.
• Be sure to install the lamp securely. If the lamp is not installed properly, it will not illuminate. Improper installation may also
result in fire.
• Do not shake the removed lamp or lift it above your face. You may injure your eye by flying or falling glass fragments.
• Do not replace the lamp immediately after use because the lamp cover is very hot. You may get burned. Turn off the power
using the STANDBY/ON button. After the lamp goes out, wait about two minutes until the intake and exhaust fans for cooling
the lamp stop rotating. Then unplug the power cable, and wait at least one hour to allow the lamp to cool down enough to
the touch.
◆ Interval of lamp replacement
The recommended interval of lamp replacement is about 3000 hours* of consecutive use when the LAMP MODE in the SETUP menu is set to
CINEMA. Such interval differs depending on the operating environment and may be shorter than 3000 hours*. Decrease in luminescence and/
or color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 2250 hours, the indicator will blink
alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator will be lit red only) and the lamp replacement
message will appear on the screen for one minute everytime the lamp is turned on. When the lamp has been used for about 2850 hours, the
replacement message (LAMP EXCHANGE) will appear on the screen for one minute every 15 hours thereafter.
When the lamp operation time exceeds 3000 hours*, the projector automatically shuts off and can not be
used until the lamp is replaced and the lamp operation time is reset.
*When the LAMP MODE is set to STANDARD, this duration will be decreased to 2000 hours.
Caution
• Be sure to use the replacement lamp cartridge PJL-725. Other lamp cartridges are not suitable for use in this projector.
• Do not remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a
breakdown.
• This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may explode or fail
to illuminate permanently because of an impact, scratch, or deterioration through use. The period of time until explosion or
permanent failure to illuminate varies considerably from lamp to lamp, depending on operation conditions. Therefore, the
lamp may explode soon after the start of use.
• The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the lamp replacement
warning appears, replace it with a new one immediately, even if the lamp is still lighting normally.
• When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and the gas
charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains mercury. Be careful not
to breathe it and avoid it from entering your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see
a doctor immediately.
• In the event that the high-pressure mercury lamp has exploded, glass fragments may have been scattered inside the
projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace the lamp
by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments.
• Do not replace the lamp with the projector installed on the ceiling. Glass fragments may fall from the projector, entering your
eye or mouth and causing injury.
• When placing the projector upside down to replace the lamp or conduct maintenance, be sure that the projector is securely
placed before working with it.
◆ Replacement lamp cartridge (Option)
Spare lamp
32
PJL-725
◆ Replacing the lamp
Warning
(a)
(c)
(b)
1.
2.
(f)
(d)
3.
4.
5.
(e)
(g)
(h)
6.
7.
8.
9.
• Do not replace the lamp immediately after using the
projector because the lamp would be extremely hot
and it may cause burns.
Carefully turn the projector upside-down (a).
Loosen the screw (b) using a Phillips screwdriver (+), and
remove the lamp cover (c).
Loosen the lamp screws (d) using a Phillips screwdriver (+).
Pull up the handle (e).
Pull out the lamp box by the handle while holding the
projector (f).
• Pull the lamp box out of the projector slowly. If it is pulled out
quickly, the lamp may break scattering glass fragments.
• Do not spill liquid on the removed lamp box or place it near any
flammable object or where children can reach to prevent fire
and injury.
Load a new lamp box securely into the projector in the right
orientation (g).
Put the handle back to the original position (h).
• Make sure that the handle is locked.
Tighten the screws (d) using a Phillips screwdriver (+).
Tighten the screw (b) using a Phillips screwdriver (+) to
secure the lamp cover.
Reset of the lamp operation time
Plug in the power cable and reset the lamp operation time by pressing and holding the
at the same time.
,
, and STANDBY/ON buttons on the control panel
Important
•
•
•
•
•
•
Unless these three buttons are pressed at the same time, the lamp operation time is not reset.
Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.
The projector does not turn on if the lamp cover is not attached securely.
Be sure to reset the lamp operation time whenever you replace the lamp, otherwise the lamp may not be turned on.
Do not reset the lamp operation time unless you replace the lamp.
This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due
to environmental considerations.
◆ Maintenance
Caution
• Be sure to turn off the lamp and unplug the power cable from the wall outlet before you perform any maintenance on the
projector.
Cleaning the projector and the ventilation grilles
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with
diluted mild detergent, and then wipe them with a dry cloth.
To protect the surface of the projector from fading or deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzine or thinner to clean it.
• Do not let rubber or plastic materials contact with projector.
Cleaning the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only
recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.
33
12 Attaching a lens filter and cap
◆ Attaching a commercially available lens filter
Closed position
(no lens filter)
(a)
(b)
1. Carefully turn the projector upside-down.
2. Loosen the screw (a) using a Phillips screwdriver (+), and
remove the stopper (b).
3. Place a lens filter (c).
4. Rotate the stopper 180° and reinsert it into its original
location (d).
5. Tighten up the screw (e) using a Phillips screwdriver (+).
Important
• Be sure to use a 67 mm lens filter for this projector.
• Not all 67 mm lens filters are compatible with this
projector.
To hold a lens filter
(e)
(d)
(c)
◆ Attaching the lens cap
Attach the supplied lens cap when not using the projector to prevent the lens from becoming dirty or damaged. Insert the lens cap until it is
securely placed. (It should make a clicking sound.)
Important
• Do not force the lens cap onto the projector.
• Make sure that the YAMAHA name on the lens cap is aligned parallel to the top and bottom edges of the projector.
• The lens cap can be placed over the lens filter if a lens filter has been installed.
34
13 Troubleshooting
◆ Troubleshooting
Refer to the chart below when this projector does not function properly. If the problem you are experiencing is not listed below or if the
instructions do not help, stop using the projector and contact your dealer.
No image appears on the screen.
Problem
Solution
Power can not be turned on.
• Check whether the indicators are on or off and how they are lightning.
POWER
Off
STATUS
Off
Solution
• Connect the power cable to the projector.
• Plug the power cable into a wall outlet.
• If any objects are blocking the air intake or exhaust vent, remove them and carry out the
following.
1.
2.
3.
4.
Off
Steady red
Blinking
orange
Blinking
green
•
•
•
•
Unplug the power cable from the wall outlet.
Make sure that the projector has cooled off.
Plug the power cable into the wall outlet.
Press the STANDBY/ON button.
If any objects are blocking the air intake or exhaust vent, remove them.
Don't expose the air exhaust vents to hot air emitted from a heating appliance.
Clean the ventilation grilles.
Relocate the projector to a cooler place.
• After the STATUS indicator stops blinking, press the STANDBY/ON button.
• If you unplug the power cable while the fan is rotating, the lamp may not turn on about
one minute when you plug the power cable next time.
• The lamp can't turn on again for one minute after it goes out.
• Press the STANDBY/ON button several times.
• Replace the lamp. (The lamp is at the end of its life.)
Steady red
• Attach the lamp cover on the bottom.
Off
Blinking
red/green
Steady
or
• Unplug the power cable from the wall outlet and contact your dealer.
Blinking
No image appears on the
screen.
•
•
•
•
•
•
•
•
Projected images suddenly
disappear.
Check that the lens cap is removed.
It may take about one minute for the lamp to light up.
The lamp fails to light up on rare occasions. In such cases, wait for a few minutes and then try again.
If the projector was turned off before the lamp cooled down completely, the fans may start rotating and the
STANDBY/ON button may not function when you plug the power cable into the wall outlet next time.
Wait for the fans to stop and press the STANDBY/ON button to turn on the lamp again.
Check that the intake vent is clean.
Check that the lamp cover is closed (see page 33).
Check that the cables connected to the external equipments are not broken.
If an extension cable is being used, replace it with the supplied cable for troubleshooting purposes. If
images are now displayed correctly, add an RGB signal amplifier to the extension cable.
• The air intake or exhaust vent may be blocked. In such cases, the STATUS indicator blinks orange. After
removing the objects blocking the intake vent and/or exhaust vents and then carry out the following
procedure:
1. Wait for the air intake or exhaust fan to stop (or wait for the STATUS indicator to go out.)
2. Unplug the power cable from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cable into the wall outlet.
5. Press the STANDBY/ON button.
6. When the STATUS indicator is steady red, it is indicating that the lamp should be replaced.
Replace the lamp with a new, commercially available lamp.
35
Problem
Solution
“NO SIGNAL” is displayed.
• Turn on the power of the connected equipment, or check whether there is something wrong with the
connected equipment.
• Check whether the external equipment outputs signals. (Check this especially when the external equipment
is a notebook computer.)
• Check that the cable connected to the external equipment is not defective.
• Check that the projector is connected to the external equipment using the correct terminals.
• Check that the connected equipment is correctly selected as the input source.
• If an extension cord is being used, replace it with the supplied cable and check whether images are
projected correctly. If images are now projected correctly, add an RGB signal amplifier to the extension
cord.
Images are not displayed correctly.
Problem
Solution
Projected images are shaking. • Check that the signal being output by the external equipment is not intermittent.
Projected images are
• Connect the cable plug firmly.
displaced.
• Press the AUTO button on the remote control or AUTO SYNC button on the projector (see page 20).
• Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu (see page 31).
Projected images are
distorted.
• Adjust the projector and the screen so that they are perpendicular to each other (see page 8).
Projected images are dark.
• Adjust BRIGHTNESS and CONTRAST in the IMAGE menu (see page 27).
• Replace the lamp (see page 32).
Projected images are blurred. • Adjust the focus (see page 16 and 19).
• Clean the lens.
•
•
•
•
Press the
or
button on the remote control to eliminate flicker.
Adjust TRACKING and PHASE in the SIGNAL menu (see page 31).
Adjust BRIGHTNESS and CONTRAST in the IMAGE menu (see page 27).
Adjust the projector and the screen so that they are perpendicular to each other (see page 8).
White dots are seen on
projected images.
Black dots are seen on
projected images.
• This symptom is normal for a DLPTM projector and is not a malfunction. (A very small number of pixels
may stay lit or out, but it is not a malfunction. Pixels of 99.99% or more are effective.)
Rainbow effect is seen on
projected images.
• This is due to color breaking noise that occurs in a DLPTM system and is not a malfunction.
Fine streaks are seen on
projected images.
• This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace
the focus a little.
Projected images become
wavy.
• Connect the cable plugs to external equipments securely.
• Keep the projector away from equipments that emit interfering radio waves.
• When the keystone adjustment is carried out, the image may not be displayed correctly because of the type
of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of
keystone correction is as small as possible.
Hue is not appropriate.
• Check that the cable connected to the external equipment is not defective.
Tint in projected images is
incorrect.
• Check that D-SUB INPUT in the SIGNAL menu is correctly set (see page 26).
• Check that the cable connected to the external equipment is not defective.
Only the motion areas in the
images supplied from the
computer are not displayed.
• This is caused by the computer being used. Contact the manufacturer of your computer.
Projected images are
obscured.
• Match the output resolution of your computer with the resolution of the projector. For the method to
change the output resolution of the computer, contact the manufacturer of your computer (see page 40).
• Some images and texts appear obscured during the keystone adjustment. In such cases, use the projector
without applying the keystone adjustment (see page 17).
36
Others
Problem
Solution
The exhaust vents emit warm • This air comes out after cooling the inside of the projector. It may feel hot, but this is not a malfunction.
air.
The menu can not be used.
• The microcomputers inside the projector may be wrongly operating because of noise.
➜Press the STANDBY/ON button to turn off the lamp and unplug the power cable from the wall outlet.
Wait about 10 minutes, plug the power cable in, and try again.
“TEMPERATURE!!” is
displayed.
• This indication appears when the ambient temperature rises high. When the ambient temperature stays
high, the lamp goes out.
➜Eliminate any causes of the rise in the ambient temperature.
• This indication appears when the air intake or exhaust vent is blocked. When they are kept blocked, the
lamp goes out.
➜Remove the objects blocking the air intake or exhaust vent.
The
• This mark appears when ineffective operation is carried out. This is not a product malfunction.
mark appears.
The remote control does not
function easily or at all.
•
•
•
•
Check that the battery is loaded in the remote control or the battery is not weak (see page 4).
Check that the remote control sensor is not exposed to direct sunlight or fluorescent light.
Use the remote control within its operation range (see page 7).
Use the remote control at least 10 cm away from the projector.
Abnormal sound is heard.
• Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions.
If the following problem occurs after the lamp is replaced, check the following first.
Problem
Solution
The projector does not turn
on.
• Fit the lamp cover securely (see page 33).
• Reset the lamp operating time (see page 33).
The STATUS indicator
blinks.
• Reset the lamp operating time (see page 33).
37
14 Indicators
This projector has two indicators, each of which shows the operation condition of the projector.
Refer to Troubleshooting for additional indication signals.
POWER indicator
STATUS indicator
STANDBY/ON button
◆ Normal conditions
POWER
STATUS
CONDITION
NOTE
Stand-by.
Steady red
Off
Warming up period (about 1 minute).
Steady green
The STANDBY/ON button cannot be used
until the STATUS indicator is steady green.
Blinking green
The projector is ready.
Steady green
Steady green
Cooling down period (lasts under 2 minutes; normal when
shutting down).
Steady red
Do not unplug the projector until the
STATUS indicator is off.
Blinking green
◆ Abnormal conditions
POWER
STATUS
Abnormal temperature
• The ventilation grilles are clogged with dust or dirt.
• The room temperature is high.
Steady green
or
CONDITION
Blinking orange
SOLUTION
• Clean the ventilation grilles.
• Relocate the projector to a cooler place.
• Remove any objects blocking the
ventilation grilles.
Steady red
Steady red
Steady green
Steady red
Steady red
Blinking
green/red
Blinking
green/red
Blinking green
Blinking green/red
Blinking red
Steady red
Abnormal when it occurs except while shutting down. The
protection circuit is working or the lamp is in an abnormal
condition.
• Wait until the STATUS indicator goes out,
then press the STANDBY/ON button.
• If the above solution is not effective,
replace the lamp.
Lamp operation time warning. (Total lamp operation time
reached 2250 hours*1 while the power was on.)
Replace the lamp.
Change with a new lamp if this problem
recurs.
Lamp operation time warning. (Total lamp operation time
reached 2250 hours*1 while the power was off.)
Lamp operation time warning. (Total lamp operation time
reached 3000 hours*1, *2 while the power was off.)
The lamp cover isn’t closed.
Close the cover correctly.
Abnormal.
Contact your dealer.
Off
Steady or Blinking
*1: When LAMP MODE of the SETUP menu is set to CINEMA.
*2: When LAMP MODE is set to STANDARD, this duration will be decreased to 2000 hours.
38
15 Specifications
◆ Projector specifications
The specifications and outside appearance of the projector are subject to change without prior notice.
Type
DLP™ projector
Model
DPX-830
Display Technology
0.65-inch Single chip DMD
Pixel 1280 × 768 = 983040 pixels
Projection lens
F 2.4 – 2.6 f= 23 – 27.6 mm
Light-source lamp
200 W
Image size (Projection distance)
40" min. to 275" max. (Projection distance 1.4 to 10.1 m (16:9 screen))
Maximum resolution
Computer signal
Maximum resolution: 1280 x 1024 dots (Analog) / compressed
Panel resolution: 1280 × 768 dots
Video signal
NTSC / PAL / SECAM / 4.43NTSC / PAL-M / PAL-N / PAL-60
Component signal
480i, 480p, 576i, 576p, 720p, 1080i
Panel resolution: 1280 × 768 dots
Input terminal
Control terminal/
Others
[Signal type]
Analog RGB
Digital RGB
Video input
S-Video input
Component video input
[Terminal type]
D-SUB 15P
HDMI
RCA × 1
S
RCA × 3, D-SUB 15P
USB
For service person
SERIAL
RS-232C (8P): For service person
TRIGGER
DC 12 V, Max.200 mA (Stereo mini jack)
Operating temperatures
+41°F (+5°C) to +95°F (+35°C)
Rated voltage
AC100 - 240 V, 50/60 Hz
Power consumption
280 W / 2.9 A
Power consumption (standby)
8W
[Line]
1
1
1
1
2
Dimensions
360 mm (W) × 102 mm (H) × 290 mm (D) *Not including protrusions.
Weight
3.9 kg
Others
S-video input
Luminance signal: Vp-p=1.0 V 75 Ω (negative sync)
Chrominance signals: Vp-p=0.286 V 75 Ω (burst signal)
Video input
Vp-p=1.0 V 75 Ω (negative sync)
Component video
input
YCBCR: Vp-p=1.0 V 75 Ω (Y) (negative sync)
Vp-p=0.7 V 75 Ω (CB, CR)
Analog RGB input
RGB: Vp-p=0.7 V 75 Ω (negative sync)
HD: TTL-level (negative or positive polarity)
VD: TTL-level (negative or positive polarity)
Digital input (HDMI) HDMI interface (TMDS single link)
39
◆ Composite / S-video signal specifications
Signal mode
Resolution
(H × V)
Horizontal frequency
(kHz)
Vertical frequency
(Hz)
Default mode for
16:9 screen
(H × V)*1
Default mode for
4:3 screen
(H × V)*2
Through mode
(H × V)
TV60 (525i)
–
15.73
59.94
1280 × 720
1024 × 576
–
TV50 (625i)
–
15.63
50.00
1280 × 720
1024 × 576
–
◆ Component signal specifications
Signal mode
Resolution
(H × V)
Horizontal frequency
(kHz)
Vertical frequency
(Hz)
Default mode for
16:9 screen
(H × V)*1
Default mode for
4:3 screen
(H × V)*2
Through mode
(H × V)
480i (525i)
–
15.73
59.94
1280 × 720
1024 × 576
–
576i (625i)
–
15.63
50.00
1280 × 720
1024 × 576
–
480p (525p)
–
31.47
59.94
1280 × 720
1024 × 576
–
576p (625p)
–
31.25
50.00
1280 × 720
1024 × 576
–
720p 60 (750p 60)
–
45.00
60.00
1280 × 720
1024 × 576
–
720p 50 (750p 50)
–
37.50
50.00
1280 × 720
1024 × 576
–
1080i 60 (1125i 60)
–
33.75
60.00
1280 × 720
1024 × 576
–
1080i 50 (1125i 50)
–
28.13
50.00
1280 × 720
1024 × 576
–
◆ Digital RGB / Component signal specifications
Signal mode
Resolution
(H × V)
Horizontal frequency
(kHz)
Vertical frequency
(Hz)
Default mode for
16:9 screen
(H × V)*1
Default mode for
4:3 screen
(H × V)*2
Through mode
(H × V)
480p (525p)
–
31.47
59.94
1280 × 720
1024 × 576
–
576p (625p)
–
31.25
50.00
1280 × 720
1024 × 576
–
720p 60 (750p 60)
–
45.00
60.00
1280 × 720
1024 × 576
–
720p 50 (750p 50)
–
37.50
50.00
1280 × 720
1024 × 576
–
1080i 60 (1125i 60)
–
33.75
60.00
1280 × 720
1024 × 576
–
1080i 50 (1125i 50)
–
28.13
50.00
1280 × 720
1024 × 576
–
VGA 60
640 × 480
31.47
59.94
960 × 720
1024 × 768
–
Through mode
(H × V)
◆ Analog RGB signal specifications
40
Signal mode
Resolution
(H × V)
Horizontal frequency
(kHz)
Vertical frequency
(Hz)
Default mode for
16:9 screen
(H × V)*1
Default mode for
4:3 screen
(H × V)*2
576i (625i)*3
–
15.63
50.00
1280 × 720
1024 × 576
–
720p 60 (750p 60)
–
45.00
60.00
1280 × 720
1024 × 576
–
720p 50 (750p 50)
–
37.50
50.00
1280 × 720
1024 × 576
–
1080i 60 (1125i 60)
–
33.75
60.00
1280 × 720
1024 × 576
–
1080i 50 (1125i 50)
–
28.13
50.00
1280 × 720
1024 × 576
–
PC98
640 × 400
24.82
56.42
1152 × 720
1024 × 640
640 × 400
CGA70
640 × 400
31.47
70.09
1152 × 720
1024 × 640
640 × 400
CGA84
640 × 400
37.86
84.13
1152 × 720
1024 × 640
640 × 400
VGA60
640 × 480
31.47
59.94
960 × 720
1024 × 768
640 × 480
VGA72
640 × 480
37.86
72.81
960 × 720
1024 × 768
640 × 480
VGA75
640 × 480
37.50
75.00
960 × 720
1024 × 768
640 × 480
VGA85
640 × 480
43.27
85.01
960 × 720
1024 × 768
640 × 480
SVGA56
800 × 600
35.16
56.25
960 × 720
1024 × 768
800 × 600
SVGA60
800 × 600
37.88
60.32
960 × 720
1024 × 768
800 × 600
SVGA72
800 × 600
48.08
72.19
960 × 720
1024 × 768
800 × 600
SVGA75
800 × 600
46.88
75.00
960 × 720
1024 × 768
800 × 600
SVGA85
800 × 600
53.67
85.06
960 × 720
1024 × 768
800 × 600
XGA60
1024 × 768
48.36
60.00
960 × 720
1024 × 768
*4
XGA70
1024 × 768
56.48
70.07
960 × 720
1024 × 768
*4
XGA75
1024 × 768
60.02
75.03
960 × 720
1024 × 768
*4
XGA85
1024 × 768
68.68
85.00
960 × 720
1024 × 768
*4
MAC13
640 × 480
35.00
66.67
960 × 720
1024 × 768
640 × 480
MAC16
832 × 624
49.72
74.55
960 × 720
1024 × 768
832 × 624
MAC19
1024 × 768
60.24
75.02
960 × 720
1024 × 768
*4
SXGA60
1280 × 1024
60.02
63.98
900 × 720
960 × 768
*4
*1:
*2:
*3:
*4:
When ASPECT in the INITIAL menu is set to DEFAULT, and SCREEN ASPECT in the SETUP menu is set to 16:9.
When ASPECT in the INITIAL menu is set to DEFAULT, and SCREEN ASPECT in the SETUP menu is set to 4:3.
Available with RGB-CS (4 line) sources from SCART terminal.
Same resolution as the DEFAUL mode depending on the each SCREEN ASPECT.
Important
• This projector can recognize 1280 × 768 pixels as the maximum resolution, however, it is programmed to recognize 1280 ×
720 or 1024 × 768 pixels as the normal resolution depending on the screen aspect.
• If the resolution and frequency of your computer are not shown on the table, find the compatible resolution and frequency by
changing the resolution of your computer.
• In the case of XGA, the right side of the image may not appear. In this case, adjust TRACKING in the SIGNAL menu.
• TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are input to the VIDEO or S-VIDEO signal,
the signal mode is indicated as TV60 or TV50. When they are input to the COMPONENT terminal, the signal mode is
indicated as 480i or 576i.
• This projector cannot be connected to other equipment via an RGB-CS (4 line) connection.
Connectors
SERIAL (8-pin)
D-SUB (Mini D-SUB 15-pin)
12
3
5
6
1 19
1
10
5
HDMI (HDMI - 19 pin)
6
15
8
11
2 18
Pin No.
Name
I/O
Pin No.
Spec.
Pin No.
Spec.
Pin No.
Spec.
Pin No.
Spec.
1
TXD
IN
1
R(RED) / CR
9
–
1
TMDS Data2+
11
2
–
–
2
G(GREEN) / Y
10
GND
TMDS Clock
Shield
3
–
–
3
B(BLUE) / CB
11
GND
2
TMDS Data2
Shield
12
TMDS Clock-
4
GND
–
4
GND
12
DDC Data
3
TMDS Data2-
13
-
5
–
–
5
GND
13
HD/CS
4
TMDS Data1+
14
-
6
–
–
6
GND
14
VD
5
15
SCL
7
RXD
OUT
7
GND
15
DDC Clock
TMDS Data1
Shield
8
–
–
8
GND
6
TMDS Data1-
16
SDA
7
TMDS Data0+
17
DDCGround
8
TMDS Data02
Shield
18
+5 V Power
9
TMDS Data0-
19
Hot Plug Detect
10
TMDS Clock+
290
◆ Dimension drawings
69
102
360
2
(Unit: mm)
41
01EN_DPX-830_EX-cv_new.fm Page 1 Monday, December 26, 2005 8:21 PM
DPX-830
DPX-830
© 2006
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
Printed in Japan
871D460A20
Digital Cinema Projector
Projecteur Cineme Numerique
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING